Radar Vectors
Certification Standard Current Issued May 31, 2024 Flight Standards Service 56 pages Copy saved Nov 19, 2026

FAA-S-8081-8C Flight Instructor Practical Test Standards for Glider Category

Official source ↗ Open PDF

FAA-S-8081-8C U.S. Department of Transportation Federal Aviation Administration

FLIGHT INSTRUCTOR

Practical Test Standards

for

Glider Category

November 2023

FLIGHT STANDARDS SERVICE

Washington, DC 20591

FOREWORD FAA-S-8081-8C, Flight Instructor Practical Test Standards for Glider Category is published by the FAA to establish the standards for flight instructor certification practical tests for the glider category. FAA inspectors and designated evaluators shall conduct practical tests in compliance with these standards. Instructors and applicants should find these standards helpful in practical test preparation.

FOREWORD

Material in FAA-S-8081-8C supersedes FAA-S-8081-8B, Flight Instructor Practical Test Standards for Glider dated, October 2006.

Table of Contents Introduction … 6 General Information … 6 PTS Concept … 6 PTS Description … 6 Abbreviations/Acronyms … 8 Use of the PTS … 9 Special Emphasis Areas … 10 Practical Test Prerequisites … 10 Aviation English Language Standard … 10 Aircraft and Equipment Requirements … 11 Evaluator Responsibility … 11 Flight Instructor Responsibility … 11 Satisfactory Performance … 12 Unsatisfactory Performance … 12 Letter of Discontinuance … 13 ADM, Risk Management, CRM, and SRM … 13 Applicant’s Use of Checklists … 13 Use of Distractions During Practical Tests … 13 Positive Exchange of Flight Controls … 14 Additional Rating Table … 15 CHECKLISTS: Applicant’s Practical Test Checklist … 16 Evaluator’s Practical Test Checklist … 17 AREAS OF OPERATION: I. FUNDAMENTALS OF INSTRUCTING … 20

Table of Contents

A. The Learning Process … 20 B. Human Behavior … 20 C. The Teaching Process … 20 D. Teaching Methods … 21 E. Critique and Evaluation … 21 F. Flight Instructor Characteristics and Responsibilities … 21 G. Planning Instructional Activity … 21

II. TECHNICAL SUBJECT AREAS … 22

A. Aeromedical Factors … 22 B. Visual Scanning and Collision Avoidance … 22 C. Use of Distractions During Flight Training … 22 D. Principles of Flight … 23 E. Elevators, Ailerons, and Rudder … 23 F. Trim, Lift, and Drag Devices … 23 G. Glider Weight and Balance … 23 H. Navigation and Flight Planning … 24 I. Regulations and Publications … 24 J. National Airspace System … 24 K. Logbook Entries and Certificate Endorsements … 25

Table of Contents › lll. PREFLIGHT PREPARATION 26

lll. PREFLIGHT PREPARATION … 26

A. Certificates and Documents … 26 B. Weather Information … 26 C. Operation of Systems … 27 D. Performance and Limitations … 27

IV. PREFLIGHT LESSON ON A MANEUVER TO BE PERFORMED IN FLIGHT … 28

A. Maneuver Lesson … 28 V. PREFLIGHT PROCEDURES … 29

A. Assembly … 29 B. Ground Handling … 29 C. Preflight Inspection … 30 D. Flight Deck Management … 31 E. Visual Signals … 31

Table of Contents › VI. AIRPORT AND GLIDERPORT OPERATIONS 32

VI. AIRPORT AND GLIDERPORT OPERATIONS … 32

A. Radio Communications … 32 B. Traffic Patterns … 32 C. Airport, Runway, and Taxiway Signs, Markings, and Lighting … 33

VII. LAUNCHES AND LANDINGS … 34 AERO TOW

A. Before Takeoff Check … 34 B. Normal and Crosswind Takeoff … 34 C. Maintaining Tow Positions … 35 D. Slack Line … 36 E. Boxing The Wake … 36 F. Tow Release … 37 G. Abnormal Occurrences … 37 GROUND TOW (AUTO OR WINCH)

Table of Contents › GROUND TOW (AUTO OR WINCH)

H. Before Takeoff Check … 38 I. Normal and Crosswind Takeoff … 38 J. Abnormal Occurrences … 39

SELF-LAUNCH

K. Engine Starting … 39 L. Taxiing … 40 M. Before Takeoff Check … 40 N. Normal and Crosswind Takeoff and Climb … 41 O. Engine Shutdown In Flight … 42 P. Engine Restart In Flight … 42 Q. Abnormal Occurrences … 43

Table of Contents › LANDINGS

LANDINGS

R. Normal and Crosswind Landing … 43 S. Slips to Landing … 44 T. Downwind Landing … 45

VIII. FUNDAMENTALS OF FLIGHT … 46

A. Straight Glides … 46 B. Turns To Headings … 46

IX. PERFORMANCE AIRSPEEDS … 47

A. Minimum Sink Airspeed … 47 B. Speed-To-Fly … 47

X. SOARING TECHNIQUES … 48

Table of Contents › X. SOARING TECHNIQUES 48

A. Thermal Soaring … 48 B. Ridge and Slope Soaring … 48 C. Wave Soaring … 49

Xl. PERFORMANCE MANEUVERS … 51

A. Steep Turns … 51 B. Recovery From a Spiral Dive … 51

XII. SLOW FLIGHT, STALLS, AND SPINS … 52

A. Maneuvering at Minimum Control Airspeed … 52 B. Stall Recognition and Recovery … 52 C. Spins … 53

Table of Contents › XIII. EMERGENCY OPERATIONS 55

XIII. EMERGENCY OPERATIONS … 55

A. Simulated Off-Airport Landing … 55 B. Emergency Equipment and Survival Gear … 55

XIV. POSTFLIGHT PROCEDURES … 56

A. After-Landing and Securing … 56

Introduction

General Information

The FAA has developed the PTS for use by FAA inspectors and evaluators when conducting the practical test.

Introduction

Throughout this PTS the following titles will be referred to as an evaluator: ASI, pilot examiner (other than administrative pilot examiners), TCE, chief instructor, assistant chief instructor, or check instructor of a pilot school holding examining authority, or authorized instructor (as applicable).

Information considered directive in nature is described in this PTS in terms such as “shall” and “must,” indicating the actions are mandatory. Guidance information is described in terms such as “should” and “may,” indicating the actions are desirable or permissive, but not mandatory.

This PTS is available for download, in PDF format, from www.faa.gov.

Comments regarding this PTS may be emailed to [email protected].

Introduction › PTS Concept

PTS Concept

14 CFR part 61 specifies the subject areas in which knowledge and skill must be demonstrated by the applicant before the issuance of a certificate. The practical test standards contain the Areas of Operation and specific Tasks in which competency shall be demonstrated. The FAA will revise this PTS whenever it is determined that changes are needed in the interest of safety. Per 14 CFR part 61, section 61.43, adherence to the practical test standards is mandatory.

Introduction › PTS Description

PTS Description

The Flight Instructor PTS for Glider includes the AREAS OF OPERATION and TASKS required for the issuance of an initial flight instructor certificate and for the addition of a category and/or class rating to that certificate.

Areas of Operation are phases of the practical test arranged in a logical sequence within this standard. They begin with Fundamentals of Instructing and end with Postflight Procedures. The evaluator may conduct the practical test in any sequence that will result in a complete and efficient test; however, the ground portion of the practical test must be accomplished before the flight portion.

Tasks are specific knowledge areas, flight procedures, or maneuvers appropriate to an Area of Operation.

Note is used to emphasize special considerations required in the Area of Operation or Task.

Reference identifies the publication(s) that describe(s) the Task. Descriptions of Tasks are not included in the standards because this information can be found in the current issue of the listed reference. Publications other than those listed may be used, for references if their content conveys substantially the same meaning as the referenced publications.

This PTS is based on the following reference list: 14 CFR part 1 Definitions and Abbreviations 14 CFR part 23 Airworthiness Standards: Normal Category Airplanes 14 CFR part 43 Maintenance, Preventive Maintenance, Rebuilding, and Alteration 14 CFR part 61 Certification: Pilots, Flight Instructors, and Ground Instructors 14 CFR part 91 General Operating and Flight Rules AC 60-28 FAA English Language Standard for an FAA Certificate Issued Under 14 CFR Parts 61, 63, 65, and 107 AC 61-65 Certification: Pilots and Flight and Ground Instructors AC 61-67 Stall and Spin Awareness Training AC 61-94 Pilot Transition Course for Self Launching or Powered Sailplanes (Motorgliders) AC 61-98 Currency Requirements and Guidance for the Flight Review and Instrument Proficiency Check AC 90-48 Pilots’ Role in Collision Avoidance AC 90-66 Non-Towered Airport Flight Operations AIM Aeronautical Information Manual FAA-H-8083-1 Weight and Balance Handbook FAA-H-8083-9 Aviation Instructor’s Handbook FAA-H-8083-13 Glider Flying Handbook FAA-H-8083-25 Pilot’s Handbook of Aeronautical Knowledge FAA-H-8083-28

Aviation Weather Handbook FAA-S-8081-22 Private Pilot PTS for Glider FAA-S-8081-23 Commercial Pilot PTS for Glider NOTAM Notice to Air Missions 49 CFR part 830 NTSB: Notification and Reporting of Aircraft Accidents or Incidents and Overdue Aircraft, and Preservation of Aircraft Wreckage, Mail, Cargo, and Records Other Glider Flight Manual Chart Supplements NOTE: Users should reference the current edition of the reference documents listed above. The current edition of all FAA publications can be found at: www.faa.gov.

The Objective lists the important elements that must be satisfactorily performed to demonstrate competency in a TASK. The Objective includes:

1. specifically what the applicant must be able to do; 2. conditions under which the TASK is to be performed; 3. acceptable performance standards, and 4. safety considerations, when applicable. The evaluator determines that the applicant meets the TASK Objective through the demonstration of competency in various elements of knowledge and/or skill. The Objectives of TASKS in certain AREAS OF OPERATION, such as Fundamentals of Instructing and Technical Subjects, include only knowledge elements. Objectives of TASKS in AREAS OF OPERATION that include elements of skill, as well as knowledge, also include common errors, which the applicant shall be able to describe, recognize, analyze, and correct. The Objective of a TASK that involves pilot skill consists of four parts. The four parts include determination that the applicant exhibits:

Introduction › Abbreviations/Acronyms

1. Instructional knowledge of the elements of a TASK. This is accomplished through descriptions, explanations, and simulated instruction. 2. Instructional knowledge of common errors related to a TASK, including their recognition, analysis, and correction. 3. The ability to demonstrate and simultaneously explain the key elements of a TASK. The TASK demonstration must be to the COMMERCIAL PILOT skill level; the teaching techniques and procedures should conform to those set forth in FAA-H-8083-9, Aviation Instructor's Handbook; and FAA-H-8083-13, Glider Flying Handbook. 4. The ability to analyze and correct common errors related to a TASK. Abbreviations/Acronyms

14 CFR Title 14 of the Code of Federal Regulations AC Advisory Circular ADM Aeronautical Decision-Making AELS Aviation English Language Standard AKTR Airman Knowledge Test Report AIM Aeronautical Information Manual AIRMET(s) Airmen’s Meteorological Information ASI Aviation Safety Inspector ATC Air Traffic Control CFIT Controlled Flight Into Terrain CG Center of Gravity CRM Crew Resource Management FAA Federal Aviation Administration FSO Flight Standards Office NOTAM Notice to Air Missions NTSB National Transportation Safety Board PIREP(s) Pilot Weather Reports PTS Practical Test Standards RPM Revolutions Per Minute SIGMET(s) Significant Meteorological SRM Single-Pilot Resource Management SOP Standard Operating Procedures SUA Special Use Airspace

Introduction › Use of the PTS

TFR Temporary Flight Restrictions U.S. United States of America Use of the PTS The FAA requires that all practical tests be conducted in accordance with the appropriate PTS. Applicants must be evaluated in all Tasks included in the Areas of Operation of the appropriate practical test standard unless otherwise noted. All of the procedures and maneuvers in the private pilot and commercial pilot PTS have been included in the flight instructor PTS; however, to permit completion of the practical test for initial certification within a reasonable timeframe, the evaluator shall select one or more TASKS in each AREA OF OPERATION. In certain AREAS OF OPERATION, there are required TASKS which the evaluator must select. These required TASKS are identified by a NOTE immediately following each AREA OF OPERATION title. In preparation for each practical test, the evaluator shall develop a written “plan of action. The evaluator will vary each “plan of action” to ensure that all TASKS in the appropriate PTS are evaluated during a given number of practical tests.

Except for required TASKS, the evaluator should avoid using the same optional TASKS in order to avoid becoming predictable. The “plan of action” for a practical test for initial certification shall include one or more TASKS in each AREA OF OPERATION and shall always include the required TASKS. The “plan of action” for a practical test for the addition of an aircraft category and/or class rating to a flight instructor certificate, shall include the required AREAS OF OPERATION as indicated in the Additional Rating Table at the beginning of each standard. The required TASKS appropriate to the additional rating(s) sought shall be included. Any TASK selected for evaluation during the practical test shall be evaluated in its entirety. The flight instructor applicant should be prepared in all knowledge and skill areas and must demonstrate the ability to instruct effectively in all TASKS included in the AREAS OF OPERATION of the appropriate PTS to pass the practical test.

Throughout the flight portion of the practical test, the evaluator shall evaluate the applicant's ability to demonstrate and simultaneously explain the selected procedures and maneuvers, and to give flight instruction to students at various stages of flight training and levels of experience. The term “instructional knowledge” means the “what,” “why,” and “how” of a subject matter topic, procedure, or maneuver. It also means that the flight instructor applicant's discussions, explanations, and descriptions should follow the recommended teaching procedures and techniques explained in FAA-H-8083-9, Aviation Instructor's Handbook. Some TASKS within the Areas of Operation require the analysis and correction of common errors. The purpose for including common errors in certain TASKS is to assist the evaluator in determining that the flight instructor applicant has the ability to recognize, analyze, and correct such errors, which is essential for flight instructor duties.

The evaluator shall not simulate any condition that may jeopardize safe flight or result in possible damage to the aircraft. The common errors listed in the TASK Objectives may or may not be found in the TASK References; however, the FAA considers their frequency of occurrence justification for their inclusion in the TASK Objectives. The evaluator shall place special emphasis on the applicant's demonstrated ability to teach precise aircraft control and sound judgment in aeronautical decision-making. Evaluation of the applicant's ability to teach judgment shall be accomplished by asking the applicant to describe the oral discussions and the presentation of practical problems that would be used in instructing students in the exercise of sound judgment. The evaluator shall also emphasize the evaluation of the applicant's demonstrated ability to teach spatial disorientation, wake turbulence and low-level wind shear avoidance, checklist usage, positive exchange of flight controls, and any other directed special emphasis areas.

Use of the PTS › Special Emphasis Areas

Special Emphasis Areas Evaluators and authorized instructors must place special emphasis upon areas of aircraft operation considered critical to flight safety. Among these are:

Introduction › Practical Test Prerequisites

1. positive aircraft control; 2. procedures for positive exchange of flight controls; 3. stall and spin awareness (if appropriate); 4. collision avoidance; 5. wake turbulence and low level windshear avoidance; 6. runway incursion avoidance; 7. CFIT; 8. aeronautical decision making/risk management; 9. checklist usage; 10. spatial disorientation; 11. TFR; 12. SUA; 13. aviation security; 14. wire strike avoidance; and 15. other areas deemed appropriate to any phase of the practical test or proficiency check. Although these areas may not be specifically addressed under each TASK, they are essential to flight safety and will be evaluated during the practical test or proficiency check. In all instances, the applicant’s actions will be evaluated in accordance to the standards of the TASKs and the ability to use good judgment with reference to the special emphasis areas listed above. Practical Test Prerequisites 14 CFR part 61, section 61.39 and subpart H, provides practical test and certification prerequisites.

Aviation English Language Standard The evaluator must determine that the applicant meets FAA AELS. An applicant for an FAA certificate or rating must be able to communicate in English in a discernible and understandable manner with ATC, pilots, and others involved in preparing an aircraft for flight and operating an aircraft in flight. This communication may or may not involve radio communications. An applicant for an FAA certificate issued in accordance with 14 CFR part 61 who cannot hear or speak due to a medical deficiency may be eligible for an FAA certificate with specific operational limitations. For additional information, reference AC 60- 28, FAA English Language Standard for an FAA Certificate Issued Under 14 CFR parts 61, 63, 65, and 107, as amended. If the applicant's ability to meet the FAA AELS comes into question before starting the practical test, the evaluator will not begin the practical test.

An evaluator who is not an ASI1 will check the box, Referred to FSO for Aviation English Language Standard Determination, located on the bottom of page 2 of the applicant’s Airman Certificate and/or Rating Application, FAA form 8710-1 or Airman Certificate and/or Rating Application-Sport Pilot, FAA form 8710-11, as applicable. The evaluator will refer the applicant to the appropriate FSO. If the applicant's ability to meet the FAA AELS comes into question after the practical test begins, an evaluator who is not an ASI will discontinue the practical test and check the box, Referred to FSO for Aviation English Language Standard Determination, on the application. The evaluator will also issue a

1 ASIs may assess an applicant’s English language proficiency in accordance with FAA Order 8900.1.

Introduction › Evaluator Responsibility

Notice of Disapproval of Application, FAA Form 8060-5 with the comment “Does Not Demonstrate FAA AELS” in addition to any unsatisfactory Task(s). In either case, the evaluator must complete and submit the application file through normal application procedures and notify the appropriate FSO of the referral. Aircraft and Equipment Requirements 14 CFR part 61, section 61.45 provides requirements for aircraft and equipment for the practical test. Evaluator Responsibility The evaluator conducting the practical test is responsible for determining that the applicant meets the acceptable standards of teaching ability, knowledge, and skill in the selected TASKS. The evaluator makes this determination by accomplishing an Objective that is appropriate to each selected TASK, and includes an evaluation of the applicant's:

Introduction › Flight Instructor Responsibility

1. ability to apply the fundamentals of instructing; 2. knowledge of, and ability to teach, the subject matter, procedures, and maneuvers covered in the TASKS; 3. ability to perform the procedures and maneuvers included in the standards to at least the COMMERCIAL PILOT skill level2 while giving effective flight instruction; and 4. ability to analyze and correct common errors related to the procedures and maneuvers covered in the TASKS. It is intended that oral questioning be used at any time during the ground or flight portion of the practical test to determine that the applicant can instruct effectively and has a comprehensive knowledge of the TASKS and their related safety factors. During the flight portion of the practical test, the evaluator shall act as a student during selected maneuvers. This will give the evaluator an opportunity to evaluate the flight instructor applicant’s ability to analyze and correct simulated common errors related to these maneuvers.

The evaluator will also evaluate the applicant’s use of visual scanning and collision avoidance procedures, and the applicant’s ability to teach those procedures. Flight Instructor Responsibility An appropriately rated flight instructor is responsible for training the flight instructor applicant to acceptable standards in all subject matter areas, procedures, and maneuvers included in the TASKS within each AREA OF OPERATION in the appropriate flight instructor PTS. Because of the impact of their teaching activities in developing safe, proficient pilots, flight instructors should exhibit a high level of knowledge, skill, and the ability to impart that knowledge and skill to students. The flight instructor shall certify that the applicant is:

1. able to make a practical application of the fundamentals of instructing; 2. competent to teach the subject matter, procedures, and maneuvers included in the standards to students with varying backgrounds and levels of experience and ability; 3. able to perform the procedures and maneuvers included in the standards to at least the COMMERCIAL PILOT skill level while giving effective flight instruction; and

2 Commercial Pilot skill level is defined as performing a procedure or maneuver within the tolerances listed in the FAA commercial pilot PTS. If the maneuver appears only in the private pilot PTS, the term means that the applicant’s performance is expected to be more precise than indicated by the stated tolerances.

Introduction › Satisfactory Performance

4. competent to pass the required practical test for the issuance of the flight instructor certificate with the associated category and class ratings or the addition of a category and/or class rating to a flight instructor certificate. Throughout the applicant's training, the flight instructor is responsible for emphasizing the performance of, and the ability to teach, effective visual scanning and collision avoidance procedures. Satisfactory Performance 14 CFR part 61, section 61.43(a), describes the satisfactory completion of the practical test for a certificate or rating.

Introduction › Unsatisfactory Performance

Unsatisfactory Performance If, in the judgment of the evaluator, the applicant does not meet the standards of performance of any Task performed, the associated Area of Operation is failed and, therefore, the practical test is failed. 14 CFR part 61, section 61.43(c) – (f) provides additional unsatisfactory performance requirements and parameters. Typical areas of unsatisfactory performance and grounds for disqualification are:

1. Any action or lack of action by the applicant that requires corrective intervention by the evaluator to maintain safe flight. 2. Failure to use proper and effective visual scanning techniques to clear the area before and while performing maneuvers. 3. Consistently exceeding tolerances stated in the Objectives. 4. Failure to take prompt corrective action when tolerances are exceeded. When a disapproval notice is issued, the evaluator will record the applicant's unsatisfactory performance in terms of Area of Operations and specific Task(s) not meeting the standard appropriate to the practical test conducted. The Area(s) of Operation/Task(s) not tested and the number of practical test failures must also be recorded. If the applicant fails the practical test because of a special emphasis area, the Notice of Disapproval must indicate the associated Task (e.g.: Area of Operation VI, Airport and Gliderport Operations, failure to use proper collision avoidance procedures).

Letter of Discontinuance › Use of Distractions During Practical Tests

Letter of Discontinuance When a practical test is discontinued for reasons other than unsatisfactory performance (e.g., equipment failure, weather, or illness) FAA Form 8710-1, Airman Certificate and/or Rating Application, and, if applicable, the AKTR, is to be returned to the applicant. The evaluator at that time prepares, signs, and issues a Letter of Discontinuance to the applicant. The Letter of Discontinuance should identify the Areas of Operation and their associated Tasks of the practical test that were successfully completed. The applicant should be advised that the Letter of Discontinuance must be presented to the evaluator when the practical test is resumed and made part of the certification file. ADM, Risk Management, CRM, and SRM Throughout the practical test, the evaluator evaluates the applicant’s ability to use good aeronautical decision-making procedures in order to identify risks.

The evaluator accomplishes this requirement by developing scenarios that incorporate as many TASKs as possible to evaluate the applicant’s risk management in making safe aeronautical decisions. For example, the evaluator may develop a scenario that incorporates weather decisions and performance planning. The applicant’s ability to utilize all the assets available in making a risk analysis to determine the safest course of action is essential for satisfactory performance. The scenarios should be realistic and within the capabilities of the aircraft used for the practical test. In assessing the applicant’s performance, the evaluator should take note of the applicant’s use of CRM and, if appropriate, SRM. CRM/SRM is the set of competencies that includes situational awareness, communication skills, teamwork, task allocation, and decision-making within a comprehensive framework of SOP. SRM specifically refers to the management of all resources onboard the aircraft, as well as outside resources available to the single-pilot.

If an applicant fails to use ADM, including CRM/SRM, as applicable in any Task, the evaluator will note that Task as failed. Applicant's Use of Checklists Throughout the practical test, the applicant is evaluated on the use of an appropriate checklist. Proper use is dependent on the specific TASK being evaluated. The situation may be such that the use of the checklist, while accomplishing elements of an Objective, would be either unsafe or impractical, especially in a single-pilot operation. In this case, a review of the checklist after the elements have been accomplished would be appropriate. Division of attention and proper visual scanning should be considered when using a checklist. Use of Distractions During Practical Tests Numerous studies indicate that many accidents have occurred when the pilot has been distracted during critical phases of flight.

To evaluate the applicant’s ability to utilize proper control techniques while dividing attention both inside and outside the flight deck, the evaluator shall cause a realistic distraction during the flight portion of the practical test to evaluate the applicant's ability to divide attention while maintaining safe flight.

Letter of Discontinuance › Positive Exchange of Flight Controls

Positive Exchange of Flight Controls During flight training, there must always be a clear understanding between students and flight instructors of who has control of the aircraft. Prior to flight, a briefing should be conducted that includes the procedure for the exchange of flight controls. A positive three-step process, subsequently described, in the exchange of flight controls between pilots is a proven procedure and one that is strongly recommended. When the instructor wishes the student to take control of the aircraft, he or she will say, “You have the flight controls.” The student acknowledges immediately by saying, “I have the flight controls.” The flight instructor again says, “You have the flight controls.” When control is returned to the instructor, follow the same procedure. A visual check is recommended to verify that the exchange has occurred. There should never be any doubt as to who is flying the aircraft.

ADDITIONAL RATING TABLE

ADDITIONAL RATING TABLE

Flight Instructor Glider

ADDITION OF A GLIDER CATEGORY RATING TO A FLIGHT

INSTRUCTOR CERTIFICATE

AREAS OF OPERATION FLIGHT INSTRUCTOR CERTIFICATE AND RATING HELD

ASE AME RH RG IAH

I NO NO NO NO NO

II YES YES YES YES YES

III YES YES YES YES YES

IV NO NO NO NO NO

Flight Instructor Glider

V YES YES YES YES YES

VI YES YES YES YES YES

VII YES* YES* YES* YES* YES*

VIII YES YES YES YES YES

IX YES YES YES YES YES

X YES YES YES YES YES

XI YES YES YES YES YES

XII YES** YES YES YES YES

XIII YES YES YES YES YES

XIV YES YES YES YES YES

LEGEND

ASE Airplane Single-Engine AME Airplane Multiengine RH Rotorcraft Helicopter RG Rotorcraft Gyroplane IAH Instrument Airplane/Helicopter

* An Evaluator shall select the kind of launch based on the applicant’s qualifications. ** Task C not required.

NOTE: The applicant who has satisfactorily accomplished ground and flight training and received an endorsement from an authorized instructor on ground tow, aero tow, and/or selflaunch procedures will be evaluated in only one kind of launch procedure. The applicant’s instructing privileges will include each kind of launch for which previously endorsed.

Flight Instructor Glider › APPLICANT’S PRACTICAL TEST CHECKLIST

APPLICANT’S PRACTICAL TEST CHECKLIST

Flight Instructor—Glider EVALUATOR’S NAME:

LOCATION:

DATE/TIME:

ACCEPTABLE AIRCRAFT

□ Aircraft Documents:

Airworthiness Certificate

Registration Certificate

Operating Limitations

□ Aircraft Maintenance Records:

Record of Airworthiness Inspections and Current Status of Applicable Airworthiness

EVALUATOR’S NAME: › ACCEPTABLE AIRCRAFT

Directives

□ Pilot’s Operating Handbook and FAA-Approved Glider Flight Manual

PERSONAL EQUIPMENT

□ PTS

□ Current Aeronautical Charts

□ Computer and Plotter

□ Flight Plan and Flight Log Forms

□ Current AIM, Charts Supplements, and Appropriate Publications

PERSONAL RECORDS

□ Identification - Photo/Signature ID

EVALUATOR’S NAME: › PERSONAL RECORDS

□ Pilot Certificate

□ Completed FAA Form 8710-1, Airman Certificate and/or Rating Application with Instructor’s

Signature (if applicable)

□ AKTR

□ Pilot Logbook with Appropriate Instructor Endorsements

□ FAA Form 8060-5, Notice of Disapproval of Application (if applicable)

□ Approved School Graduation Certificate (if applicable)

□ Evaluator’s Fee (if applicable)

Flight Instructor Glider › EVALUATOR’S PRACTICAL TEST CHECKLIST

EVALUATOR’S PRACTICAL TEST CHECKLIST

Flight Instructor—Glider APPLICANT'S NAME: LOCATION: DATE/TIME:

I. FUNDAMENTALS OF INSTRUCTING

A. The Learning Process B. Human Behavior C. The Teaching Process D. Teaching Methods E. Critique and Evaluation F. Flight Instructor Characteristics and Responsibilities G. Planning Instructional Activity

DATE/TIME: › II. TECHNICAL SUBJECT AREAS

II. TECHNICAL SUBJECT AREAS

A. Aeromedical Factors B. Visual Scanning and Collision Avoidance C. Use of Distractions During Flight Training D. Principles of Flight E. Elevators, Ailerons, and Rudder F. Trim, Lift, and Drag Devices G. Glider Weight and Balance H. Navigation and Flight Planning I. Regulations and Publications J. National Airspace System K. Logbook Entries and Certificate Endorsements

DATE/TIME: › III. PREFLIGHT PREPARATION

III. PREFLIGHT PREPARATION

A. Certificates and Documents B. Weather Information C. Operation of Systems D. Performance and Limitations

IV. PREFLIGHT LESSON ON A MANEUVER TO BE PERFORMED IN FLIGHT

A. Maneuver Lesson

V. PREFLIGHT PROCEDURES

A. Assembly B. Ground Handling C. Preflight Inspection D. Flight Deck Management E. Visual Signals

DATE/TIME: › VI. AIRPORT AND GLIDERPORT OPERATIONS

VI. AIRPORT AND GLIDERPORT OPERATIONS

A. Radio Communications B. Traffic Patterns C. Airport, Runway, and Taxiway Signs, Markings, and Lighting VII. LAUNCHES AND LANDINGS AERO TOW

A. Before Takeoff Check B. Normal and Crosswind Takeoff C. Maintaining Tow Positions D. Slack Line E. Boxing The Wake F. Tow Release G. Abnormal Occurrences GROUND TOW (AUTO OR WINCH)

DATE/TIME: › SELF-LAUNCH

H. Before Takeoff Check I. Normal and Crosswind Takeoff J. Abnormal Occurrences SELF-LAUNCH

K. Engine Starting L. Taxiing M. Before Takeoff Check N. Normal and Crosswind Takeoff and Climb O. Engine Shutdown In Flight P. Engine Restart In Flight Q. Abnormal Occurrences LANDINGS

R. Normal and Crosswind Landing S. Slips to Landing T. Downwind Landing VIII. FUNDAMENTALS OF FLIGHT

DATE/TIME: › IX. PERFORMANCE AIRSPEEDS

A. Straight Glides B. Turns to Headings IX. PERFORMANCE AIRSPEEDS

A. Minimum Sink Airspeed B. Speed-To-Fly

X. SOARING TECHNIQUES

A. Thermal Soaring B. Ridge and Slope Soaring C. Wave Soaring XI. PERFORMANCE MANEUVERS

A. Steep Turns B. Recovery From a Spiral Dive XII. SLOW FLIGHT, STALLS, AND SPINS

DATE/TIME: › XIII. EMERGENCY OPERATIONS

A. Maneuvering at Minimum Control Airspeed B. Stall Recognition and Recovery C. Spins XIII. EMERGENCY OPERATIONS

A. Simulated Off-Airport Landing B. Emergency Equipment and Survival Gear XIV. POSTFLIGHT PROCEDURES

A. After-Landing and Securing

I. AREA OF OPERATION: FUNDAMENTALS OF INSTRUCTING NOTE: The evaluator will select at least TASKs E and F. A. TASK: THE LEARNING PROCESS REFERENCE: FAA-H-8083-9. Objective. To determine that the applicant exhibits instructional knowledge of the elements of the learning process by describing:

I. AREA OF OPERATION: FUNDAMENTALS OF INSTRUCTING › B. TASK: HUMAN BEHAVIOR

1. The definition and characteristics of learning. 2. Practical application of the laws of learning. 3. Factors involved in how people learn. 4. Recognition and proper use of the various levels of learning. 5. Principles that are applied in learning a skill. 6. Factors of forgetting and retention. 7. How the transfer of learning affects the learning process. 8. How the formation of habit patterns affects the learning process. B. TASK: HUMAN BEHAVIOR REFERENCE: FAA-H-8083-9. Objective. To determine that the applicant exhibits instructional knowledge of the elements of human behavior by describing:

I. AREA OF OPERATION: FUNDAMENTALS OF INSTRUCTING › C. TASK: THE TEACHING PROCESS

1. Control of human behavior. 2. Development of student potential. 3. Relationship of human needs to behavior and learning. 4. Relationship of defense mechanisms to student learning and pilot decision-making. 5. General rules that a flight instructor should follow during student training to ensure good human relations. C. TASK: THE TEACHING PROCESS REFERENCE: FAA-H-8083-9. Objective. To determine that the applicant exhibits instructional knowledge of the elements of the teaching process by describing:

1. Preparation of a lesson for a ground or flight instructional period. 2. Presentation of knowledge and skills, including the methods, which are suitable in particular situations. 3. Application, by the student, of the knowledge and skills presented by the instructor. 4. Review of the material presented and the evaluation of student performance and accomplishment.

I. AREA OF OPERATION: FUNDAMENTALS OF INSTRUCTING › D. TASK: TEACHING METHODS

D. TASK: TEACHING METHODS REFERENCE: FAA-H-8083-9. Objective. To determine that the applicant exhibits instructional knowledge of the elements of teaching methods by describing:

1. The organization of a lesson (i.e., introduction, development, and conclusion). 2. The lecture method. 3. The guided discussion method. 4. The demonstration-performance method. 5. Computer and/or video assisted instruction. E. TASK: CRITIQUE AND EVALUATION REFERENCE: FAA-H-8083-9. Objective. To determine that the applicant exhibits instructional knowledge of the elements of critique and evaluation by describing:

I. AREA OF OPERATION: FUNDAMENTALS OF INSTRUCTING › E. TASK: CRITIQUE AND EVALUATION

1. Purpose and characteristics of an effective critique. 2. Difference between critique and evaluation. 3. Characteristics of effective oral questions and what type to avoid. 4. Responses to student questions. 5. Characteristics and development of effective written tests. 6. Characteristics and uses of performance tests, specifically, the FAA PTS.

I. AREA OF OPERATION: FUNDAMENTALS OF INSTRUCTING › F. TASK: FLIGHT INSTRUCTOR CHARACTERISTICS AND RESPONSIBILITIES

F. TASK: FLIGHT INSTRUCTOR CHARACTERISTICS AND RESPONSIBILITIES REFERENCE: FAA-H-8083-9. Objective. To determine that the applicant exhibits instructional knowledge of the elements of flight instructor characteristics and responsibilities by describing:

1. Characteristics and qualifications of a professional flight instructor. 2. Role of the flight instructor in dealing with student stress, anxiety, and psychological abnormalities. 3. Flight instructor's responsibility with regard to student pilot supervision and surveillance. 4. Flight instructor's authority and responsibility for endorsements and recommendations. 5. Flight instructor's responsibility in the conduct of the required FAA flight review. G. TASK: PLANNING INSTRUCTIONAL ACTIVITY REFERENCE: FAA-H-8083-9. Objective. To determine that the applicant exhibits instructional knowledge of the elements of planning instructional activity by describing:

I. AREA OF OPERATION: FUNDAMENTALS OF INSTRUCTING › G. TASK: PLANNING INSTRUCTIONAL ACTIVITY

1. Development of a course of training. 2. Content and use of a training syllabus. 3. Purpose, characteristics, proper use, and items of a lesson plan. 4. Flexibility features of a course of training, syllabus, and lesson plan required to accommodate students with varying backgrounds, levels of experience, and ability.

II. AREA OF OPERATION: TECHNICAL SUBJECT AREAS › A. TASK: AEROMEDICAL FACTORS

II. AREA OF OPERATION: TECHNICAL SUBJECT AREAS

NOTE: The evaluator will select TASK K and at least one other TASK. A. TASK: AEROMEDICAL FACTORS REFERENCES: FAA-H-8083-13; AIM. Objective. To determine that the applicant exhibits instructional knowledge of the elements related to aeromedical factors by describing:

II. AREA OF OPERATION: TECHNICAL SUBJECT AREAS › B. TASK: VISUAL SCANNING AND COLLISION AVOIDANCE

1. Hypoxia, its symptoms, effects, and corrective action. 2. Hyperventilation, its symptoms, effects, and corrective action. 3. Middle ear and sinus problems, their causes, effects, and corrective action. 4. Spatial disorientation, its causes, effects, and corrective action. 5. Motion sickness, its causes, effects, and corrective action. 6. Effects of alcohol and drugs, and their relationship to safety. 7. Effects of dehydration and their relationship to flight safety. 8. Carbon monoxide poisoning, its symptoms, effects, and corrective action (self-launch). 9. How evolved gas from scuba diving can affect a pilot during flight. 10. Stress and fatigue causes, effects, and corrective actions. 11. Visual illusions. B. TASK: VISUAL SCANNING AND COLLISION AVOIDANCE REFERENCES: FAA-H-8083-25; AC 90-48; AIM. Objective. To determine that the applicant exhibits instructional knowledge of the elements of visual scanning and collision avoidance by describing:

1. Relationship between a pilot’s physical or mental condition and vision. 2. Environmental conditions and optical illusions that affect vision. 3. “See and avoid” concept. 4. Practice of “time sharing” of attention inside and outside the flight deck. 5. Proper visual scanning technique. 6. Relationship between poor visual scanning habits, aircraft speed differential, and increased collision risk. 7. Appropriate clearing procedures. 8. Situations, which involve the greatest collision, risk.

II. AREA OF OPERATION: TECHNICAL SUBJECT AREAS › C. TASK: USE OF DISTRACTIONS DURING FLIGHT TRAINING

C. TASK: USE OF DISTRACTIONS DURING FLIGHT TRAINING REFERENCE: AC 61-67. Objective. To determine that the applicant exhibits instructional knowledge of the elements related to use of distractions during flight training by describing:

1. Flight situations where pilot distraction can be a causal factor related to aircraft accidents. 2. Selection of realistic distractions for specific flight situations. 3. Relationship between division of attention and flight instructor’s use of distractions. 4. Difference between proper use of distractions and harassment.

II. AREA OF OPERATION: TECHNICAL SUBJECT AREAS › D. TASK: PRINCIPLES OF FLIGHT

D. TASK: PRINCIPLES OF FLIGHT REFERENCES: FAA-H-8083-13. Objective. To determine that the applicant exhibits instructional knowledge of the elements related to principles of flight by describing:

1. Glider and airfoil design characteristics. 2. The three axes of rotation and stability about those axes. 3. Lift/drag relationship. 4. Forces acting on a glider in straight flight and turns. 5. Stalls and spins. E. TASK: ELEVATORS, AILERONS, AND RUDDER REFERENCES: FAA-H-8083-13. Objective. To determine that the applicant exhibits instructional knowledge of the elements related to elevators, ailerons, and rudder by describing:

II. AREA OF OPERATION: TECHNICAL SUBJECT AREAS › F. TASK: TRIM, LIFT, AND DRAG DEVICES

1. Purpose of each primary control. 2. Location, attachments, and system of control. 3. Direction of movement relative to airflow. 4. Effect on glider control. 5. Proper technique for use. 6. Adverse yaw. F. TASK: TRIM, LIFT, AND DRAG DEVICES REFERENCES: FAA-H-8083-13; Glider Flight Manual. Objective. To determine that the applicant exhibits instructional knowledge of the elements related to trim, lift, and drag devices by describing:

II. AREA OF OPERATION: TECHNICAL SUBJECT AREAS › G. TASK: GLIDER WEIGHT AND BALANCE

1. Purpose. 2. Location, attachments, and system of control. 3. Direction of trim movement relative to airflow and the primary control surface. 4. Effect on glider control. 5. Proper technique for use. G. TASK: GLIDER WEIGHT AND BALANCE REFERENCES: FAA-H-8083-1; Glider Flight Manual. Objective. To determine that the applicant exhibits instructional knowledge of the elements of glider weight and balance by describing:

1. Weight and balance terms. 2. Effect of weight and balance on performance. 3. Determination of total weight, CG, and changes that occur when adding, removing, or shifting weight. 4. Purpose and effect of removable ballast on performance.

II. AREA OF OPERATION: TECHNICAL SUBJECT AREAS › H. TASK: NAVIGATION AND FLIGHT PLANNING

H. TASK: NAVIGATION AND FLIGHT PLANNING REFERENCES: FAA-H-8083-13; AIM. Objective. To determine that the applicant exhibits instructional knowledge of the elements related to navigation and flight planning by describing:

1. Terms used in navigation. 2. Importance of using proper and current aeronautical charts. 3. Features of aeronautical charts to include identification of various types of airspace and symbols. 4. Method of plotting a course and selecting prominent en route checkpoints. 5. Fundamentals of pilotage and dead reckoning. 6. Importance of a weather check and the use of good judgment in making a “go/no-go” decision. 7. Construction of a flight profile to determine minimum flight altitude required at “go-ahead points.” 8. Factors that should be considered in the selection of a suitable landing area in the event an offairport landing must be accomplished. I. TASK: REGULATIONS AND PUBLICATIONS REFERENCES: 14 CFR parts 1, 61, 91; 49 CFR part 830; AC 61-94; AIM; Glider Flight Manual. Objective. To determine that the applicant exhibits instructional knowledge of the elements related to regulations and publications, their purpose, general content, availability, and method of revision by describing:

II. AREA OF OPERATION: TECHNICAL SUBJECT AREAS › J. TASK: NATIONAL AIRSPACE SYSTEM

1. 14 CFR parts 1, 61, and 91. 2. 49 CFR part 830. 3. Flight Information Publications. 4. PTS. 5. Glider Flight Manual, if applicable. J. TASK: NATIONAL AIRSPACE SYSTEM REFERENCES: 14 CFR part 91; AIM. Objective. To determine that the applicant exhibits instructional knowledge of the elements related to the national airspace system by describing:

1. General dimensions and operating requirements of airspace classes. 2. Operating limitations associated with controlled, uncontrolled, special use, and other airspace, TFRs.

II. AREA OF OPERATION: TECHNICAL SUBJECT AREAS › K. TASK: LOGBOOK ENTRIES AND CERTIFICATE ENDORSEMENTS

K. TASK: LOGBOOK ENTRIES AND CERTIFICATE ENDORSEMENTS REFERENCES: 14 CFR part 61; AC 61-65, AC 61-98. Objective. To determine that the applicant exhibits instructional knowledge of the elements related to logbook entries and certificate endorsements by describing:

1. Required logbook entries for instruction given, including type of launches. 2. Required student pilot certificate endorsements, including appropriate logbook entries. 3. Preparation of a recommendation for a pilot practical test, including the appropriate logbook entry. 4. Required endorsement of a pilot logbook for the satisfactory completion of an FAA flight review. 5. Required flight instructor records.

III. AREA OF OPERATION: PREFLIGHT PREPARATION › A. TASK: CERTIFICATES AND DOCUMENTS

III. AREA OF OPERATION: PREFLIGHT PREPARATION NOTE: The evaluator will select at least one TASK. A. TASK: CERTIFICATES AND DOCUMENTS REFERENCES: 14 CFR parts 43, 61, 91; FAA-H-8083-13; Glider Flight Manual. Objective. To determine that the applicant exhibits instructional knowledge of the elements related to certificates and documents by describing:

III. AREA OF OPERATION: PREFLIGHT PREPARATION › B. TASK: WEATHER INFORMATION

1. Requirements for issuance of pilot and flight instructor certificates and ratings, and the privileges and limitations of those certificates and ratings. 2. Medical fitness. 3. Airworthiness and registration certificates. 4. Glider flight manuals. 5. Glider maintenance/inspection requirements and associated records. B. TASK: WEATHER INFORMATION REFERENCES: FAA-H-8083-13, FAA-H-8083-28; NOTAM. Objective. To determine that the applicant exhibits instructional knowledge of the elements related to weather information by describing:

1. Importance of a thorough weather check. 2. Various sources for obtaining weather information. 3. Use of weather reports, forecasts, and charts, including stability charts. 4. Use of PIREPs, SlGMETs, and AlRMETs. 5. Recognition of aviation weather hazards and their effects on glider operations. 6. Factors to be considered in making a “go/no-go” decision. 7. The relationship of the following factors to the lifting process—

a. pressure and temperature lapse rates. b. atmospheric instability. c. thermal index and thermal production. d. cloud formation and identification. e. frontal weather. f. land, sea, and valley breezes. g. orographic lift. h. mountain waves.

III. AREA OF OPERATION: PREFLIGHT PREPARATION › C. TASK: OPERATION OF SYSTEMS

C. TASK: OPERATION OF SYSTEMS REFERENCES: FAA-H-8083-13; Glider Flight Manual. Objective. To determine that the applicant exhibits instructional knowledge of the elements related to the operation of systems of the glider used for the practical test, by describing:

1. Magnetic compass. 2. Yaw string or inclinometer. 3. Airspeed indicator and altimeter. 4. Variometer and total energy compensator. 5. Gyroscopic instruments. 6. Electrical. 7. Landing gear and brakes. 8. Avionics. 9. Oxygen equipment. D. TASK: PERFORMANCE AND LIMITATIONS REFERENCES: FAA-H-8083-13; Glider Flight Manual. Objective. To determine that the applicant exhibits instructional knowledge of the elements related to performance and limitations by describing:

III. AREA OF OPERATION: PREFLIGHT PREPARATION › D. TASK: PERFORMANCE AND LIMITATIONS

1. Determination of weight and balance condition. 2. Use of performance charts and other data for determining performance in various phases of flight. 3. Effects of density altitude, wind, and other atmospheric conditions on performance. 4. Applicable performance speeds, and their uses. 5. Relationship between airspeeds and load factors. 6. Purpose and effect of water ballast on performance. 7. Factors to be considered in determining that the required performance is within the glider’s capabilities and limitations.

IV. › A. TASK: MANEUVER LESSON

IV. AREA OF OPERATION: PREFLIGHT LESSON ON A MANEUVER TO BE PERFORMED IN FLIGHT

NOTE: The evaluator shall select at least one maneuver from AREAS OF OPERATION VlI through Xll, and ask the applicant to present a preflight lesson on the selected maneuver as the lesson would be taught to a student. Previously developed lesson plans from the applicant’s library may be used. A. TASK: MANEUVER LESSON REFERENCES: FAA-H-8083-9, FAA-H-8083-13; Glider Flight Manual. Objective. To determine that the applicant exhibits instructional knowledge of the selected maneuver by:

1. Using a lesson plan that includes all essential items to make an effective and organized presentation. 2. Stating the objective. 3. Giving an accurate, comprehensive oral description of the maneuver, including the elements and associated common errors. 4. Using instructional aids, as appropriate. 5. Describing the recognition, analysis, and correction of common errors.

V. AREA OF OPERATION: PREFLIGHT PROCEDURES › A. TASK: ASSEMBLY

V. AREA OF OPERATION: PREFLIGHT PROCEDURES NOTE: The evaluator will select at least one TASK. A. TASK: ASSEMBLY REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to assembly by describing—

a. selection of a suitable assembly area and sufficient crewmembers for assembly. b. importance of following a checklist. c. proper handling of components. d. cleaning and lubricating parts, as appropriate. e. post-assembly inspection, to include accounting for parts, tools, and making a positive

control check.

2. Exhibits instructional knowledge of common errors related to assembly by describing—

a. poor planning with regard to selection of a suitable assembly area, or the availability of

sufficient number of crewmembers for assembly. b. failure to use a checklist. c. careless handling of components. d. failure to clean and lubricate parts, as appropriate. e. omission, or careless performance, of a post-assembly inspection, including a

positive control check.

V. AREA OF OPERATION: PREFLIGHT PROCEDURES › B. TASK: GROUND HANDLING

3. Demonstrates and simultaneously explains assembly from an instructional standpoint. B. TASK: GROUND HANDLING REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to ground handling by describing—

a. selection and use of proper ground handling equipment for existing conditions. b. proper positioning and use of a sufficient number of crewmembers. c. proper positioning and securing of controls. d. precautions to be taken with regard to the canopy(ies). e. importance of ensuring that placards or cautions are observed when handling glider

structure. f. importance of following a suitable route, using an appropriate speed, and being aware of obstructions.

2. Exhibits instructional knowledge of common errors related to ground handling by describing—

V. AREA OF OPERATION: PREFLIGHT PROCEDURES › C. TASK: PREFLIGHT INSPECTION

a. failure to select and use proper ground handling equipment. b. hazards of attempting to move the glider with an insufficient number of crewmembers. c. failure to properly position or secure controls. d. failure to secure canopy(ies). e. failure to follow directions stated on placards. f. poor choice of route, use of inappropriate speed, and lack of obstruction awareness. 3. Demonstrates and simultaneously explains ground handling from an instructional standpoint. 4. Analyzes and corrects common errors related to ground handling. C. TASK: PREFLIGHT INSPECTION REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to a preflight inspection, as appropriate, to the glider used for the practical test, by describing—

a. reasons for the preflight inspection, items that should be inspected, and how defects are

detected. b. importance of using an appropriate checklist. c. inspection of oxygen system, if applicable. d. detection of visible structural damage. e. determination that glider components are properly assembled and attachments secure,

including flight controls. f. ballast management, including CG weights and water ballast. g. inspection of towline, tow hitch, weak link, and release mechanism. h. use of sound judgment in determining whether glider is in condition for safe flight.

2. Exhibits instructional knowledge of common errors related to a preflight inspection by describing—

a. failure to use, or improper use of, the checklist. b. hazards that may result from allowing distractions to interrupt a preflight inspection. c. inability to recognize discrepancies.

3. Demonstrates and simultaneously explains a preflight inspection from an instructional standpoint. 4. Analyzes and corrects common errors related to a preflight inspection.

V. AREA OF OPERATION: PREFLIGHT PROCEDURES › D. TASK: FLIGHT DECK MANAGEMENT

D. TASK: FLIGHT DECK MANAGEMENT REFERENCES: 14 CFR part 91; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements of flight deck management by describing—

a. proper arranging and securing of essential materials and equipment in the flight deck. b. proper use and/or adjustment of flight deck items, such as safety belts, shoulder harnesses,

rudder pedals, seats, and parachutes. c. occupant briefing on emergency procedures, and use of safety belts and shoulder

harnesses.

2. Exhibits instructional knowledge of common errors related to flight deck management by describing—

a. failure to place and secure essential materials and equipment for easy access during

flight. b. improper adjustment of equipment and controls. c. failure to brief occupants on emergency procedures, and use of safety belts and shoulder

harnesses.

V. AREA OF OPERATION: PREFLIGHT PROCEDURES › E. TASK: VISUAL SIGNALS

3. Demonstrates and simultaneously explains flight deck management from an instructional standpoint. E. TASK: VISUAL SIGNALS NOTE: The applicant’s competence with regard to emergency signals may be evaluated through oral testing. REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to visual signals by describing the—

a. pre-launch signals, including purpose of and proper response to each. b. launch signals, including purpose of and proper response to each. c. airborne signals, including purpose of and proper response to each. d. emergency signals, including purpose of and proper response to each.

2. Exhibits instructional knowledge of common errors related to visual signals by describing the—

a. improper transmission of pre-launch and launch signals to crewmembers. b. improper response to launch signals. c. improper transmission of airborne signals to tow pilot. d. improper response to airborne signals from tow pilot. e. improper transmission of, or response to, airborne emergency signals.

3. Demonstrates and simultaneously explains visual signals from an instructional standpoint. 4. Analyzes and corrects common errors related to visual signals.

VI. AREA OF OPERATION: AIRPORT AND GLIDERPORT OPERATIONS › A. TASK: RADIO COMMUNICATIONS

VI. AREA OF OPERATION: AIRPORT AND GLIDERPORT OPERATIONS NOTE: The evaluator shall select at least one TASK. A. TASK: RADIO COMMUNICATIONS REFERENCES: FAA-H-8083-25; AIM; FAA-S-8081-22, FAA-S-8081- 23. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements of radio communications by describing—

a. selection and use of appropriate radio frequencies. b. recommended procedure and phraseology for radio voice communications, as described in

the AIM. c. receipt, acknowledgment of, and compliance with, ATC clearances and other instructions. d. prescribed procedure for radio communications failure. e. interpretation of, and compliance with, ATC light signals. 2. Exhibits instructional knowledge of common errors related to radio communications by describing—

VI. AREA OF OPERATION: AIRPORT AND GLIDERPORT OPERATIONS › B. TASK: TRAFFIC PATTERNS

a. use of improper frequencies. b. improper techniques and phraseologies when using radio voice communications. c. failure to acknowledge, or properly comply with, ATC clearances and other instructions. d. use of improper procedures for radio communications failure. e. failure to understand, or to properly comply with, ATC light signals. B. TASK: TRAFFIC PATTERNS REFERENCES: AC 90-66; FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to traffic patterns by describing—

a. segments (or legs) and procedures applicable to flying a normal glider traffic pattern. b. importance of pilot awareness of co-existing traffic patterns/runways, use of proper visual

scanning technique, and maintenance of spacing on other aircraft. c. completion of pre-landing checklist. d. appropriate airspeed and proper technique for wind drift correction. e. selection of touchdown and stop points. f. appropriate corrections and compensations for lift and sink areas. g. considerations for wind shear. h. proper planning and use of flaps, spoilers, and/or dive brakes.

2. Exhibits instructional knowledge of common errors related to traffic patterns by describing—

a. failure to scan properly and have appropriate spacing. b. poorly planned entry leg. c. improper correction for wind drift. d. rough or uncoordinated control technique. e. poor judgment in the selection of touchdown and stop points. f. failure to maintain appropriate airspeed. g. failure to apply needed corrections at various points in the pattern.

h. hazards of a low base leg and a low uncoordinated turn to final.

3. Demonstrates and simultaneously explains traffic patterns from an instructional standpoint. 4. Analyzes and corrects common errors related to traffic patterns.

VI. AREA OF OPERATION: AIRPORT AND GLIDERPORT OPERATIONS › C. TASK: AIRPORT, RUNWAY, AND TAXIWAY SIGNS, MARKINGS, AND LIGHTING

C. TASK: AIRPORT, RUNWAY, AND TAXIWAY SIGNS, MARKINGS, AND LIGHTING REFERENCES: AIM; FAA-H-8083-9; FAA-S-8081-22, FAA-S-8081- 23. Objective. To determine that the applicant exhibits instructional knowledge of the elements of airport, runway, and taxiway signs, markings, and lighting by describing:

1. Identification and proper interpretation of airport, runway, and taxiway signs, and markings. 2. Identification and proper interpretation of airport, runway, and taxiway lighting.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › A. TASK: BEFORE TAKEOFF CHECK

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS NOTE: Evaluator will select kind of launch based on the applicant’s qualifications. AERO TOW NOTE: The evaluator will select at least one TASK. A. TASK: BEFORE TAKEOFF CHECK REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to the before takeoff check by describing— a. reason for performing each checklist item. b. establishment, with crewmembers, of a proper course of action, including visual signals,

speeds, wind, and emergency procedures. c. proper procedure for setting altimeter, checking and adjusting controls, and closing and

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › B. TASK: NORMAL AND CROSSWIND TAKEOFF

securing canopy(ies). d. use of the appropriate hitch for the type of launch to be conducted. e. proper procedure for checking towline hookup and release mechanism. f. importance of reviewing takeoff emergency procedures. g. method used for ensuring adequate clearance from other traffic. 2. Exhibits instructional knowledge of common errors related to the before takeoff check by describing— a. omission or improper accomplishment of essential items. b. failure to use proper visual signals. c. failure to check or properly adjust controls. d. failure to follow proper procedure for checking towline hookup and release mechanism. e. hazards of failing to review takeoff emergency procedures. 3. Demonstrates and simultaneously explains the before takeoff check from an instructional standpoint. 4. Analyzes and corrects common errors related to the before takeoff check. B. TASK: NORMAL AND CROSSWIND TAKEOFF REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to a normal and crosswind takeoff by describing—

a. glider configuration and positioning on the runway. b. initial positioning of controls. c. use of proper pre-launch and launch visual signals. d. directional control during takeoff roll. e. crosswind control technique.

f. proper lift-off attitude, maintenance of alignment with the towplane, and climbout technique.

2. Exhibits instructional knowledge of common errors related to a normal and crosswind takeoff by describing—

a. improper glider configuration. b. improper initial positioning of flight controls. c. use of improper visual signals. d. failure to maintain alignment behind towplane before towplane becomes airborne. e. improper position relative to towplane during liftoff. f. improper glider position, in crosswind, after towplane becomes airborne.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › C. TASK: MAINTAINING TOW POSITIONS

3. Demonstrates and simultaneously explains a normal or crosswind takeoff from an instructional standpoint. 4. Analyzes and corrects common errors related to a normal or crosswind takeoff. C. TASK: MAINTAINING TOW POSITIONS REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to maintaining tow positions by describing—

a. high tow and low tow, including purpose, recognition, and control technique for each. b. wake turbulence associated with towplane. c. proper technique for transitioning between high-tow and low-tow positions. d. proper technique for performing turns on tow. e. over-control and under-control while on tow.

2. Exhibits instructional knowledge of common errors related to maintaining tow positions by describing—

a. faulty technique with regard to proper vertical and lateral positions during high tow and low

tow. b. faulty technique during transition between high tow and low tow. c. inadvertent entry into towplane wake turbulence. d. initiation of a turn too early or at an angle of bank greater than that of the towplane. e. initiation of a turn too late or at an angle of bank less than that of the towplane.

3. Demonstrates and simultaneously explains maintaining tow positions from an instructional standpoint. 4. Analyzes and corrects common errors related to maintaining tow positions.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › D. TASK: SLACK LINE

D. TASK: SLACK LINE REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to slack line by describing—

a. situations that lead to development of slack line. b. hazards of slack line. c. techniques, which can be used to correct slack line in various situations.

2. Exhibits instructional knowledge of common errors related to slack line by describing—

a. failure to take corrective action at the first indication of slack line development. b. use of an improper technique to correct slack line. c. a faulty corrective technique, which can result in excessive stress on towline, weak link,

and glider structure.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › E. TASK: BOXING THE WAKE

3. Demonstrates and simultaneously explains slack line from an instructional standpoint. 4. Analyzes and corrects common errors related to slack line. E. TASK: BOXING THE WAKE REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to boxing the wake by describing—

a. performance of a rectangular pattern that keeps glider slightly outside the wake. b. proper control technique and coordination. c. importance of maintaining a taut towline.

2. Exhibits instructional knowledge of common errors related to boxing the wake by describing—

a. performance of an excessively large rectangle (moving too far from the wake). b. inappropriate control coordination and technique. c. abrupt or rapid changes of position.

3. Demonstrates and simultaneously explains boxing the wake from an instructional standpoint. 4. Analyzes and corrects common errors related to boxing the wake.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › F. TASK: TOW RELEASE

F. TASK: TOW RELEASE REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to tow release by describing—

a. why release should be accomplished with normal tension on towline. b. advisability of ensuring that area is clear of other aircraft prior to release. c. clearing turn, which should be made by glider and towplane immediately after release. d. situations when an immediate release should be accomplished.

2. Exhibits instructional knowledge of common errors related to tow release by describing—

a. lack of tension on the towline. b. failure to clear area prior to release. c. failure to make proper turn after release. d. release in close proximity to aircraft other than towplane.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › G. TASK: ABNORMAL OCCURRENCES

3. Demonstrates and simultaneously explains tow release from an instructional standpoint. 4. Analyzes and corrects common errors related to tow release. G. TASK: ABNORMAL OCCURRENCES REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23. Objective. To determine that the applicant exhibits instructional knowledge of elements related to abnormal occurrences by describing:

1. Why glider pilot and towplane pilot should agree on a course of action prior to flight. 2. Proper glider pilot response in the event of—

a. towplane power loss during takeoff. b. towline break. c. towplane power failure at altitude. d. glider release failure. e. glider and towplane release failure.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › H. TASK: BEFORE TAKEOFF CHECK

GROUND TOW (AUTO OR WINCH) NOTE: The evaluator will select at least one TASK. H. TASK: BEFORE TAKEOFF CHECK REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to the before takeoff check by describing—

a. reason for performing each checklist item. b. establishment, with crewmembers, of a proper course of action, including visual signals,

speeds, wind, and emergency procedures. c. proper procedure for setting altimeter, checking and adjusting controls, and closing and

securing canopy(ies). d. use of the appropriate hitch for the type of launch to be conducted. e. proper procedure for checking towline hookup and release mechanism. f. importance of reviewing takeoff emergency procedures. g. method used for ensuring adequate clearance from other traffic.

2. Exhibits instructional knowledge of common errors related to the before takeoff check by describing—

a. omission or improper accomplishment of essential items. b. failure to use proper visual signals. c. failure to check or properly adjust controls. d. failure to follow the proper procedure for checking the towline hookup and release

mechanism. e. Hazards of failure to review takeoff emergency procedures.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › I. TASK: NORMAL AND CROSSWIND TAKEOFF

3. Demonstrates and simultaneously explains the before takeoff check from an instructional standpoint. 4. Analyzes and corrects common errors related to the before takeoff check. I. TASK: NORMAL AND CROSSWIND TAKEOFF REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to a normal and crosswind takeoff by describing—

a. proper calculation of launch airspeed. b. glider configuration and positioning on the runway. c. initial positioning of controls. d. use of proper pre-launch and launch visual signals. e. directional control during takeoff roll. f. crosswind control technique. g. pitch attitude and groundtrack during climb.

h. proper technique for making adjustments of airspeed and for porpoising. i. proper towline release technique.

2. Exhibits instructional knowledge of common errors related to a normal and crosswind takeoff by describing—

a. improper glider configuration. b. improper initial positioning of flight controls. c. use of improper visual signals. d. improper crosswind technique. e. improper climb profile. f. faulty corrective action for adjustment of airspeed and porpoising. g. exceeding maximum launch airspeed. h. improper towline release technique and timing.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › J. TASK: ABNORMAL OCCURRENCES

3. Demonstrates and simultaneously explains a normal or a crosswind takeoff from an instructional standpoint. 4. Analyzes and corrects common errors related to a normal or a crosswind takeoff. J. TASK: ABNORMAL OCCURRENCES REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant exhibits instructional knowledge of elements related to abnormal occurrences by describing:

1. Why the glider pilot and crewmembers should agree on a course of action prior to launch. 2. Proper glider pilot response in the event of—

a. overrunning the towline. b. launch power failure or towline break. c. inability to release towline. d. porpoising.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › K. TASK: ENGINE STARTING

3. Methods for emergency release or severance of towline. SELF-LAUNCH NOTE: The evaluator will select at least one TASK. K. TASK: ENGINE STARTING REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements of engine starting by describing—

a. importance of using the appropriate checklist. b. safety precautions related to engine starting. c. effect of atmospheric conditions on engine starting. d. starting procedure, as appropriate. e. adjustment of engine controls during start. f. prevention of glider movement during and after engine start.

2. Exhibits instructional knowledge of common errors related to engine starting by describing—

a. failure to use or improper use of the checklist. b. improper or unsafe starting procedure. c. excessively high RPM after starting. d. failure to ensure proper clearance of propeller.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › L. TASK: TAXIING

3. Demonstrates and simultaneously explains engine starting from an instructional standpoint. 4. Analyzes and corrects common errors related to engine starting. L. TASK: TAXIING REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to taxiing by describing—

a. proper brake check and correct use of brakes. b. compliance with airport surface markings, signals, and clearances. c. how to control direction and speed. d. control positioning for various wind conditions. e. techniques used to avoid other aircraft and hazards, considering wingspan and

maneuvering space required.

2. Exhibits instructional knowledge of the common errors related to taxiing by describing—

a. improper use of brakes. b. failure to comply with markings, signals, or clearances. c. hazards of taxiing too fast. d. improper positioning of flight controls for various wind conditions. e. failure to consider wingspan and space required to maneuver during taxiing.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › M. TASK: BEFORE TAKEOFF CHECK

3. Demonstrates and simultaneously explains taxiing from an instructional standpoint. 4. Analyzes and corrects common errors related to taxiing. M. TASK: BEFORE TAKEOFF CHECK REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the before takeoff check by describing—

a. positioning glider to avoid creating hazards. b. division of attention inside and outside the flight deck. c. importance of following a checklist and responding to each item. d. reasons for ensuring suitable engine temperatures and pressures for run-up and takeoff. e. method used to determine that the glider is in a safe operating condition. f. importance of reviewing takeoff performance airspeeds, expected takeoff distances, wind, and emergency procedures. g. methods for ensuring that takeoff area is free of hazards. h. methods of ensuring adequate clearance from other traffic.

2. Exhibits instructional knowledge of common errors related to the before takeoff check by describing—

a. improper positioning of the glider. b. failure to use or improper use of the checklist. c. acceptance of marginal engine performance. d. improper check of flight controls. e. hazards of failure to review takeoff and emergency procedures. f. failure to check for hazards and other traffic.

3. Demonstrates and simultaneously explains the before takeoff check from an instructional standpoint. 4. Analyzes and corrects common errors related to the before takeoff check.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › N. TASK: NORMAL AND CROSSWIND TAKEOFF AND CLIMB

N. TASK: NORMAL AND CROSSWIND TAKEOFF AND CLIMB REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to a normal and crosswind takeoff and climb by describing—

a. alignment with takeoff path. b. initial positioning of flight controls. c. power application. d. directional control during acceleration on the surface. e. crosswind control technique during acceleration on the surface. f. lift-off attitude and airspeed. g. climb attitude, power setting, and airspeed. h. crosswind correction and track during climb. i. use of checklist, as appropriate.

2. Exhibits instructional knowledge of common errors related to a normal and crosswind takeoff and climb by describing—

a. improper initial positioning of flight controls. b. improper power application. c. inappropriate removal of hand from throttle. d. poor directional control. e. improper use of ailerons. f. improper pitch attitude during liftoff. g. failure to establish and maintain proper climb attitude and airspeed. h. drift during climb.

3. Demonstrates and simultaneously explains a normal or crosswind takeoff and climb from an instructional standpoint. 4. Analyzes and corrects common errors related to a normal or crosswind takeoff and climb.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › O. TASK: ENGINE SHUTDOWN IN FLIGHT (if applicable)

O. TASK: ENGINE SHUTDOWN IN FLIGHT (if applicable) REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to engine shutdown in flight by describing—

a. establishment of manufacturer’s recommended power setting to ensure engine cooling

prior to shutdown. b. establishment of appropriate airspeed. c. shutdown of unnecessary electrical equipment, if appropriate. d. manufacturer’s recommended propeller feathering, positioning, and stowing procedure. e. selection of proper static source, if appropriate.

2. Exhibits instructional knowledge of common errors related to engine shutdown in flight by describing—

a. failure to set engine at idle for the specified period of time. b. initiation of feathering procedure at an inappropriate airspeed. c. failure to follow manufacturer’s recommended propeller feathering, positioning, and

stowing procedure. d. improper setting of electrical equipment. e. failure to maintain positive aircraft control while performing engine shutdown procedures.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › P. TASK: ENGINE RESTART IN FLIGHT (if applicable)

3. Demonstrates and simultaneously explains engine shutdown in flight from an instructional standpoint. 4. Analyzes and corrects common errors related to engine shutdown in flight. P. TASK: ENGINE RESTART IN FLIGHT (if applicable) REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to engine restart in flight by describing—

a. establishment of the proper airspeed. b. altitude available to consider restart. c. manufacturer’s propeller repositioning and unfeathering procedure. d. operation of engine controls. e. procedure for starting engine by starter or by windmilling. f. proper engine warm-up procedure. g. selection of proper static source, if appropriate. h. proper setting of electrical equipment. i. proper adjustment of propeller pitch.

2. Exhibits instructional knowledge of common errors related to engine restart in flight by describing—

a. failure to establish recommended airspeed. b. performance of improper propeller repositioning and unfeathering procedure. c. failure to properly operate engine controls. d. failure to follow prescribed procedure for starting engine by starter or windmilling. e. improper procedure for warm-up. f. improper setting of electrical equipment. g. failure to maintain positive aircraft control while performing engine restart procedures.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › Q. TASK: ABNORMAL OCCURRENCES

3. Demonstrates and simultaneously explains engine restart in flight from an instructional standpoint. 4. Analyzes and corrects common errors related to engine restart in flight. Q. TASK: ABNORMAL OCCURRENCES REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant exhibits instructional knowledge of the elements related to abnormal occurrences by describing recommended pilot action for:

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › R. TASK: NORMAL AND CROSSWIND LANDING

1. Partial or complete power failure or failure to gain restart. 2. Smoke or fire during ground or flight operations. 3. Loss of engine oil pressure. 4. Low fuel pressure. 5. Engine overheat. 6. Electrical system malfunction. 7. Canopy opening in flight. LANDINGS NOTE: The evaluator will select at least one TASK. R. TASK: NORMAL AND CROSSWIND LANDING REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to a normal and crosswind landing by describing—

a. obstructions and other hazards, which should be considered. b. how to determine wind speed and direction. c. proper glidepath to the selected touchdown area, at the recommended airspeed. d. proper use of flaps, spoilers, and dive brakes. e. coordination of flight controls and use of trim. f. crosswind control technique. g. timing, judgment, and control technique during roundout and touchdown. h. directional control after touchdown. i. appropriate wing attitude and proper use of brakes after touchdown.

2. Exhibits instructional knowledge of common errors related to a normal and crosswind landing by describing—

a. poor judgment of glidepath and improper use of flaps, spoilers, and dive brakes. b. rough, hesitant, or uncoordinated control technique. c. improper airspeed control. d. improper correction for crosswind. e. improper technique during roundout and touchdown. f. poor directional control after touchdown. g. improper use of brakes.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › S. TASK: SLIPS TO LANDING

3. Demonstrates and simultaneously explains a normal or a crosswind landing from an instructional standpoint. 4. Analyzes and corrects common errors related to a normal or a crosswind landing. S. TASK: SLIPS TO LANDING REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to slips to landing by describing—

a. forward, side, and turning slips, with and without the use of drag devices. b. obstacles and other hazards, which should be considered. c. possible airspeed indication errors. d. proper control usage and crosswind technique. e. timing, judgment, and control technique during transition from slip to touchdown. f. directional control after touchdown. g. appropriate wing attitude and proper use of brakes after touchdown.

2. Exhibits instructional knowledge of common errors related to slips to landing by describing—

a. failure to establish recommended glider configuration. b. failure to use proper technique to achieve touchdown accuracy. c. rough, hesitant, or uncoordinated use of controls. d. improper correction for crosswind. e. improper technique during roundout and touchdown. f. poor directional control after touchdown. g. improper use of brakes.

3. Demonstrates and simultaneously explains a slip to landing (without use of drag devices) from an instructional standpoint. 4. Analyzes and corrects common errors related to a slip to \landing.

VlI. AREA OF OPERATION: LAUNCHES AND LANDINGS › T. TASK: DOWNWIND LANDING

T. TASK: DOWNWIND LANDING REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to a downwind landing by describing—

a. obstructions and other hazards, which should be considered. b. windspeed above which a downwind landing should not be attempted. c. length of the final approach compared with that of a normal landing. d. proper glidepath to selected touchdown area, at the re commended airspeed. e. proper use of flaps, spoilers, and dive brakes to achieve accuracy of touchdown. f. coordination of flight controls and use of trim. g. appropriate correction for wind. h. timing, judgment, and control technique during roundout and touchdown. i. directional control after touchdown. j. appropriate wing attitude and proper use of brakes after touchdown.

2. Exhibits instructional knowledge of common errors related to a downwind landing by describing—

a. poor judgment of glidepath and the improper use of flaps, spoilers, and dive brakes. b. rough, hesitant, or uncoordinated use of controls. c. unintentional slowing of airspeed due to higher groundspeed. d. improper correction for wind. e. improper technique during roundout and touchdown. f. poor directional control after touchdown. g. improper use of brakes.

3. Demonstrates and simultaneously explains a downwind landing from an instructional standpoint. 4. Analyzes and corrects common errors related to a downwind landing.

VIII. AREA OF OPERATION: FUNDAMENTALS OF FLIGHT › A. TASK: STRAIGHT GLIDES

VIII. AREA OF OPERATION: FUNDAMENTALS OF FLIGHT NOTE: The evaluator will select at least one TASK. A. TASK: STRAIGHT GLIDES REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to straight glides by describing—

a. pitch attitude and airspeed. b. establishment and maintenance of a precise ground track. c. effect of flaps, spoilers, and dive brakes. d. use of smooth and coordinated control applications. e. use of trim.

2. Exhibits instructional knowledge of common errors related to straight glides by describing—

a. rough or erratic pitch attitude and airspeed control. b. failure to establish and maintain proper wind drift correction. c. effect of improper use of controls when using flaps, spoilers, and dive brakes. d. rough, uncoordinated, or inappropriate control applications. e. failure to trim or improper use of trim.

VIII. AREA OF OPERATION: FUNDAMENTALS OF FLIGHT › B. TASK: TURNS TO HEADINGS

3. Demonstrates and simultaneously explains straight glides from an instructional standpoint. 4. Analyzes and corrects common errors related to straight glides. B. TASK: TURNS TO HEADINGS REFERENCES: FAA-H-8083-9; FAA-H-8083-13, FAA-S-8081-22, FAA-S-8081-23. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to turns to headings by describing—

a. proper pitch attitude, angle of bank, and airspeed. b. roll-in and roll-out technique. c. changes in lift, drag, and load factor. d. adverse yaw. e. use of smooth and coordinated control applications.

2. Exhibits instructional knowledge of common errors related to turns to headings by describing—

a. rough or uncoordinated use of controls during roll-in and roll-out. b. failure to establish desired angle of bank. c. lack of precision in completion of a turn to a heading.

3. Demonstrates and simultaneously explains turns to headings from an instructional standpoint. 4. Analyzes and corrects common errors related to turns to headings.

IX. AREA OF OPERATION: PERFORMANCE AIRSPEEDS › A. TASK: MINIMUM SINK AIRSPEED

IX. AREA OF OPERATION: PERFORMANCE AIRSPEEDS NOTE: The evaluator will select at least one TASK. A. TASK: MINIMUM SINK AIRSPEED REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to minimum sink airspeed by describing—

a. related aerodynamic factors. b. use of this speed. c. establishment and maintenance of this speed.

2. Exhibits instructional knowledge of common errors related to minimum sink airspeed by describing—

a. incorrect determination of this speed. b. rough or erratic pitch attitude and airspeed control.

IX. AREA OF OPERATION: PERFORMANCE AIRSPEEDS › B. TASK: SPEED-TO-FLY

3. Demonstrates and simultaneously explains minimum sink airspeed from an instructional standpoint. 4. Analyzes and corrects common errors related to minimum sink airspeed. B. TASK: SPEED-TO-FLY REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23; Glider Flight Manual. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to speed-to-fly by describing—

a. factors related to the determination of speed-to-fly. b. use of this speed. c. establishment and maintenance of this speed for a given situation.

2. Exhibits instructional knowledge of common errors related to speed-to-fly by describing—

a. improper determination of this speed. b. rough or erratic pitch attitude and airspeed control.

3. Demonstrates and simultaneously explains speed-to-fly from an instructional standpoint. 4. Analyzes and corrects common errors related to speed-to-fly.

X. AREA OF OPERATION: SOARING TECHNIQUES › A. TASK: THERMAL SOARING

X. AREA OF OPERATION: SOARING TECHNIQUES NOTE: The evaluator will select at least one TASK. The TASK selected will be appropriate to the geographical location and existing atmospheric conditions. If conditions do not permit a demonstration of soaring skills, applicants will be expected to demonstrate satisfactory instructional knowledge of the selected TASK through oral testing. A. TASK: THERMAL SOARING REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to thermal soaring by describing—

a. the process by which thermals are produced. b. recognition of the presence of a thermal. c. initial entry into a thermal. d. analysis of a thermal’s structure and determination of the direction of turn to remain within

a thermal. e. coordinated use of controls and proper planning to remain within a thermal. f. importance of maintaining orientation with ground references, wind, and other aircraft. g. importance of maintaining proper airspeeds in and between thermals. h. use of proper techniques to re-enter a thermal.

2. Exhibits instructional knowledge of common errors related to thermal soaring by describing—

a. failure to maintain proper airspeeds in and between thermals. b. poor division of attention resulting in failure to recognize \when entering or flying out of a

thermal. c. improper technique during initial entry into a thermal. d. faulty control coordination and planning to remain within a thermal. e. faulty division of attention in maintaining orientation with ground references and wind. f. failure to properly scan for other aircraft. g. poor planning and technique when attempting to re-enter a thermal.

X. AREA OF OPERATION: SOARING TECHNIQUES › B. TASK: RIDGE AND SLOPE SOARING

3. Demonstrates and simultaneously explains thermal soaring from an instructional standpoint. 4. Analyzes and corrects common errors related to thermal soaring. B. TASK: RIDGE AND SLOPE SOARING REFERENCES: FAA-H-8083-9, FAA-H-8083-13; FAA-S-8081-22, FAA-S-8081-23. Objective. To determine that the applicant:

1. Exhibits instructional knowledge of the elements related to ridge and slope soaring by describing—

a. terrain features and wind conditions that create orographic lift. b. importance of an accurate estimate of terrain height. c. initial entry into an area of lift. d. importance of smooth, precise, and coordinated use of controls. e. maintenance of a safe lateral distance from the terrain. f. use of proper techniques to re-enter an area of lift. g. procedures for approaching and crossing ridges.

h. importance of planning to fly within a safe gliding distance of an acceptable landing area. i. maintenance of orientation with ground references and other aircraft. j. importance of being constantly alert for changing weather conditions.

2. Exhibits instructional knowledge of common errors related to ridge and slope soaring by describing—

a. hazards of approaching the ridge or slope lift area at approximately a 90° angle or from the

downwind side. b. failure to maintain proper airspeed while in the area of lift. c. poor division of attention resulting in failure to promptly recognize when leaving the area of

lift or entering a high sink area. d. poor control coordination. e. poor division of attention in maintaining orientation with ground references and wind. f. failure to properly scan for other aircraft. g. failure to plan the flight so an acceptable landing area is within gliding distance.

Continue reading ↓ 120 of 133 passages shown