AC 00-6B Aviation Weather
This advisory circular (AC) was published by the Federal Aviation Administration (FAA) Flight Standards Service (AFS), with contributions from the National Weather Service (NWS). The publication began in 1943 as CAA Bulletin No. 25, Meteorology for Pilots, which at the time contained weather knowledge considered essential for most pilots. As aircraft flew farther, faster, and higher, and as meteorological knowledge grew, the bulletin became obsolete. It was revised in 1954 under a new title, The Pilots’ Weather Handbook, and updated again in 1965. In 1975 it was revised under its current title.
This document is cancelled. It may have been replaced. Check the official source before relying on it.
AC 00-6B_FAA Web
U.S. Department of Transportation Federal Aviation Administration
Advisory Circular
Subject: Aviation Weather Date: 8/23/16 AC No: 00-6B Initiated by: AFS-400 Change:
This advisory circular (AC) was published by the Federal Aviation Administration (FAA) Flight Standards Service (AFS), with contributions from the National Weather Service (NWS). The publication began in 1943 as CAA Bulletin No. 25, Meteorology for Pilots, which at the time contained weather knowledge considered essential for most pilots. As aircraft flew farther, faster, and higher, and as meteorological knowledge grew, the bulletin became obsolete. It was revised in 1954 under a new title, The Pilots’ Weather Handbook, and updated again in 1965. In 1975 it was revised under its current title.
Previous editions have suffered one common problem—they dealt in part with weather services that continually change, in keeping with current techniques and service demands. As a result, each edition was somewhat outdated almost as soon as it was published, its obsolescence growing throughout the period it remained in print.
In 1975, in order to alleviate this problem, the authors completely rewrote the AC. They streamlined it into a clear, concise, readable book, and omitted all reference to specific weather services.
The 1975 text remained valid and adequate for many years. Its companion manual, the current edition of AC 00-45, Aviation Weather Services, supplements this AC. In 2015, this supplement was updated concurrently with this text. This was done to reflect changes brought about by new products and services, particularly since this information is now available through the Internet. The companion AC describes current weather services and formats, and uses real world examples of weather graphics and text products.
The two manuals can be downloaded for free via the Internet in PDF format. Print versions are also sold separately at nominal cost, allowing pilots the opportunity to own a reference copy of the supplement to keep current with aviation weather services.
New scientific capabilities now necessitate an update to this AC. In 1975, aviation users were not directly touched by radar and satellite weather. In 2016, much of what airmen understand about the current atmosphere comes from these important data sources. This AC is intended to provide basic weather information that all airmen must know. This document is intended to be used as a resource for pilot and dispatcher training programs.
This AC cancels AC 00-6A, Aviation Weather for Pilots and Flight Operations Personnel.
John Barbagallo Deputy Director, Flight Standards Service
iii
CONTENTS Paragraph Page
Chapter 1. The Earth’s Atmosphere … 1-1
1.1 Introduction … 1-1
1.2 Composition … 1-1
1.2.1 Air Parcel … 1-2
1.3 Vertical Structure … 1-2
1.3.1 Troposphere … 1-2
1.3.2 Stratosphere … 1-3
1.3.3 Mesosphere … 1-4
1.3.4 Thermosphere … 1-5
1.3.5 Exosphere … 1-5
1.4 The Standard Atmosphere … 1-5
Chapter 2. Heat and Temperature … 2-1
2.1 Introduction … 2-1
2.2 Matter … 2-1
2.3 Energy … 2-1
2.4 Heat … 2-1
2.5 Temperature … 2-1
2.5.1 Temperature Measurement … 2-1
2.5.2 Temperature Scales … 2-1
2.6 Heat Transfer … 2-3
2.6.1 Radiation … 2-3
2.6.2 Conduction … 2-6
2.6.3 Convection … 2-7
2.7 Thermal Response … 2-8
2.8 Temperature Variations with Altitude … 2-11
2.8.1 Atmospheric Sounding … 2-12
2.8.2 Isothermal Layer … 2-12
2.8.3 Temperature Inversion … 2-12
iv
Chapter 3. Water Vapor … 3-1
3.1 Introduction … 3-1
3.2 The Hydrologic Cycle … 3-1
3.2.1 Evaporation … 3-2
3.2.2 Transpiration … 3-2
3.2.3 Sublimation … 3-2
3.2.4 Condensation … 3-2
3.2.5 Transportation … 3-2
3.2.6 Precipitation … 3-2
3.2.7 Runoff … 3-2
3.2.8 Infiltration … 3-2
3.2.9 Groundwater Flow … 3-3
3.2.10 Plant Uptake … 3-3
3.3 Saturation … 3-3
3.4 Relative Humidity … 3-3
3.5 Dewpoint … 3-4
3.6 Temperature-Dewpoint Spread (Dewpoint Depression) … 3-4
3.7 Change of Phase … 3-5
3.7.1 Latent Heat … 3-5
Chapter 4. Earth-Atmosphere Heat Imbalances … 4-1
4.1 Introduction … 4-1
4.2 The Earth-Atmosphere Energy Balance … 4-1
4.3 Heat Imbalances Between Earth’s Surface and the Atmosphere … 4-3
4.3.1 Sensible Heating … 4-3
4.3.2 Latent Heat … 4-4
4.4 Heat Imbalance Variations with Latitude … 4-4
4.5 Seasons … 4-5
4.6 Diurnal Temperature Variation … 4-7
Chapter 5. Atmospheric Pressure and Altimetry … 5-1
5.1 Introduction … 5-1
v
5.2 Atmospheric Pressure … 5-1
5.2.1 Barometer … 5-2
5.2.2 Atmospheric Pressure Units … 5-2
5.2.3 Station Pressure … 5-3
5.2.4 Pressure Variation … 5-3
5.2.5 Sea Level Pressure … 5-5
5.2.6 Constant Pressure Surface … 5-7
5.3 Density … 5-10
5.3.1 Volume Effects on Density … 5-10
5.3.2 Changes in Density … 5-11
5.3.3 Density Effects on Pressure … 5-11
5.3.4 Temperature Effects on Density … 5-12
5.3.5 Water Vapor Effects on Density … 5-12
5.4 Altimetry … 5-13
5.4.1 Altitude … 5-13
5.5 Density Altitude … 5-16
Chapter 6. Weather Charts … 6-1
6.1 Introduction … 6-1
6.2 Weather Observation Sources … 6-1
6.3 Analysis … 6-2
6.3.1 Analysis Procedure … 6-2
6.4 Surface Chart … 6-6
6.5 Constant Pressure Chart … 6-7
Chapter 7. Wind … 7-1
7.1 Introduction … 7-1
7.2 Naming of the Wind … 7-1
7.3 Forces That Affect the Wind … 7-1
7.3.1 Pressure Gradient Force (PGF) … 7-1
7.3.2 Coriolis Force … 7-2
7.3.3 Friction Force … 7-4
7.4 Upper Air Wind … 7-5
7.5 Surface Wind … 7-6
vi
Chapter 8. Global Circulations and Jet Streams … 8-1
8.1 Non-Rotating Earth Circulation System … 8-1
8.2 Rotating Earth Circulation System … 8-1
8.3 Jet Streams … 8-2
8.3.1 Introduction … 8-2
8.3.2 Direction of Wind Flow … 8-3
8.3.3 Location … 8-4
Chapter 9. Local Winds … 9-1
9.1 Description … 9-1
9.2 Hazards … 9-2
9.3 Sea Breeze … 9-2
9.3.1 Sea Breeze Front … 9-3
9.3.2 Effects of Coastline Shape … 9-3
9.4 Land Breeze … 9-4
9.5 Lake Breeze … 9-5
9.6 Valley Breeze … 9-7
9.7 Mountain-Plains Wind System … 9-8
9.8 Mountain Breeze … 9-9
Chapter 10. Air Masses, Fronts, and the Wave Cyclone Model … 10-1
10.1 Air Masses … 10-1
10.1.1 Air Mass Classification … 10-1
10.1.2 Air Mass Modification … 10-2
10.2 Fronts … 10-3
10.3 The Wave Cyclone Model … 10-7
10.4 Dryline … 10-9
Chapter 11. Vertical Motion and Cloud Formation … 11-1
11.1 Introduction … 11-1
11.2 Vertical Motion Effects on an Unsaturated Air Parcel … 11-1
11.3 Vertical Motion Effects on a Saturated Air Parcel … 11-2
11.4 Common Sources of Vertical Motion … 11-5
11.4.1 Orographic Effects … 11-5
11.4.2 Frictional Effects … 11-6
vii
11.4.3 Frontal Lift … 11-6
11.4.4 Buoyancy … 11-7
Chapter 12. Atmospheric Stability … 12-1
12.1 Introduction … 12-1
12.2 Using a Parcel as a Tool to Evaluate Stability … 12-1
12.3 Stability Types … 12-1
12.3.1 Absolute Stability … 12-1
12.3.2 Neutral Stability … 12-2
12.3.3 Absolute Instability … 12-3
12.3.4 Conditional Instability … 12-4
12.3.5 Summary of Stability Types … 12-6
12.4 Processes that Change Atmospheric Stability … 12-7
12.4.1 Wind Effects on Stability … 12-7
12.4.2 Vertical Air Motion Effects on Stability … 12-7
12.4.3 Diurnal Temperature Variation Effects on Stability … 12-8
12.5 Measurements of Stability … 12-9
12.5.1 Lifted Index … 12-9
12.5.2 Convective Available Potential Energy … 12-10
12.6 Summary … 12-11
Chapter 13. Clouds … 13-1
13.1 Introduction … 13-1
13.2 Cloud Forms … 13-1
13.3 Cloud Levels … 13-2
13.4 Cloud Types … 13-2
13.4.1 High Clouds … 13-2
13.4.2 Middle Clouds … 13-5
13.4.3 Low Clouds … 13-9
Chapter 14. Precipitation … 14-1
14.1 Introduction … 14-1
14.2 Necessary Ingredients for Formation … 14-1
14.3 Growth Process … 14-1
14.4 Precipitation Types … 14-3
viii
Chapter 15. Adverse Wind … 15-1
15.1 Introduction … 15-1
15.2 Crosswind … 15-1
15.3 Gust … 15-1
15.4 Tailwind … 15-2
15.5 Variable Wind/Sudden Wind Shift … 15-2
15.6 Wind Shear … 15-2
Chapter 16. Weather, Obstructions to Visibility, Low Ceiling, and Mountain Obscuration .... 16-1
16.1 Weather and Obstructions to Visibility … 16-1
16.1.1 Fog … 16-1
16.1.2 Mist … 16-5
16.1.3 Haze … 16-5
16.1.4 Smoke … 16-5
16.1.5 Precipitation … 16-5
16.1.6 Blowing Snow … 16-6
16.1.7 Dust Storm … 16-6
16.1.8 Sandstorm … 16-6
16.1.9 Volcanic Ash … 16-7
16.2 Low Ceiling and Mountain Obscuration … 16-8
16.2.1 Low Ceiling … 16-8
16.2.2 Mountain Obscuration … 16-9
Chapter 17. Turbulence … 17-1
17.1 Introduction … 17-1
17.2 Causes of Turbulence … 17-1
17.2.1 Convective Turbulence … 17-1
17.2.2 Mechanical Turbulence … 17-3
17.2.3 Wind Shear Turbulence … 17-5
17.3 Turbulence Factors … 17-6
Chapter 18. Icing … 18-1
18.1 Introduction … 18-1
18.2 Supercooled Water … 18-1
ix
18.3 Structural Icing … 18-1
18.3.1 Rime Icing … 18-1
18.3.2 Clear Icing … 18-1
18.3.3 Mixed Icing … 18-2
18.3.4 Icing Factors … 18-2
18.3.5 Icing in Stratiform Clouds … 18-4
18.3.6 Icing in Cumuliform Clouds … 18-4
18.3.7 Icing with Fronts … 18-4
18.3.8 Icing with Mountains … 18-5
18.3.9 Icing Hazards … 18-6
18.4 Engine Icing … 18-7
18.4.1 Carburetor Icing … 18-7
18.4.2 High Ice Water Content (HIWC) … 18-7
Chapter 19. Thunderstorms … 19-1
19.1 Introduction … 19-1
19.2 Necessary Ingredients for Thunderstorm Cell Formation … 19-1
19.3 Thunderstorm Cell Life Cycle … 19-1
19.4 Thunderstorm Types … 19-2
19.5 Factors that Influence Thunderstorm Motion … 19-5
19.6 Hazards … 19-6
19.6.1 Lightning … 19-6
19.6.2 Adverse Wind … 19-6
19.6.3 Downburst … 19-6
19.6.4 Turbulence … 19-8
19.6.5 Icing … 19-8
19.6.6 Hail … 19-9
19.6.7 Rapid Altimeter Changes … 19-10
19.6.8 Static Electricity … 19-10
19.6.9 Tornado … 19-10
x
Chapter 20. Weather Radar … 20-1
20.1 Principles of Weather Radar … 20-1
20.1.1 Antenna … 20-1
20.1.2 Backscattered Energy … 20-1
20.1.3 Power Output … 20-2
20.1.4 Wavelengths … 20-2
20.1.5 Attenuation … 20-3
20.1.6 Resolution … 20-4
20.1.7 Wave Propagation … 20-7
20.1.8 Intensity of Precipitation … 20-9
Chapter 21. Tropical Weather … 21-1
21.1 Circulation … 21-1
21.1.1 Subtropical High Pressure Belts … 21-1
21.1.2 Trade Wind Belts … 21-3
21.1.3 The Intertropical Convergence Zone (ITCZ) … 21-5
21.1.4 Monsoon … 21-5
21.2 Transitory Systems … 21-7
21.2.1 Remnants of Polar Fronts and Shear Lines … 21-7
21.2.2 Tropical Upper Tropospheric Trough (TUTT) … 21-8
21.2.3 Tropical Wave … 21-9
21.2.4 West African Disturbance Line (WADL) … 21-10
21.2.5 Tropical Cyclones … 21-11
Chapter 22. Arctic Weather … 22-1
22.1 Introduction … 22-1
22.2 Climate, Air Masses, and Fronts … 22-1
22.2.1 Long Days and Nights … 22-2
22.2.2 Land and Water … 22-2
22.2.3 Temperature … 22-2
22.2.4 Clouds and Precipitation … 22-2
22.2.5 Wind … 22-3
22.2.6 Air Masses—Winter … 22-3
xi
22.2.7 Air Masses—Summer … 22-3
22.2.8 Fronts … 22-3
22.3 Arctic Peculiarities … 22-3
22.3.1 Effects of Temperature Inversion … 22-3
22.3.2 Light Reflection by Snow-Covered Surfaces … 22-3
22.3.3 Light from Celestial Bodies … 22-3
22.4 Weather Hazards … 22-4
22.4.1 Fog and Ice Fog … 22-4
22.4.2 Blowing and Drifting Snow … 22-4
22.4.3 Frost … 22-4
22.4.4 Whiteout … 22-4
Chapter 23. Space Weather … 23-1
23.1 The Sun—Prime Source of Space Weather … 23-1
23.2 The Sun’s Energy Output and Variability … 23-1
23.3 Sunspots and the Solar Cycle … 23-1
23.4 Solar Wind … 23-1
23.5 Solar Eruptive Activity … 23-2
23.6 Geospace … 23-2
23.7 Galactic Cosmic Radiation … 23-3
23.8 Geomagnetic Storms … 23-4
23.9 Solar Radiation Storms … 23-4
23.10 Ionospheric Storms … 23-5
23.11 Solar Flare Radio Blackouts … 23-5
23.12 Effects of Space Weather on Aircraft Operations … 23-6
23.12.1 Communications … 23-6
23.12.2 Navigation and Global Positioning System (GPS) … 23-6
23.12.3 Radiation Exposure to Flight Crews and Passengers … 23-6
23.12.4 Radiation Effects on Avionics … 23-6
xii
List of Figures
Figure 1-1. Vertical Structure of the Atmosphere … 1-4
Figure 1-2. U.S. Standard Atmosphere within the Troposphere … 1-6
Figure 2-1. Comparison of Kelvin, Celsius, and Fahrenheit Temperature Scales … 2-3
Figure 2-2. Radiation Example … 2-4
Figure 2-3. Temperature’s Effect on Radiation Wavelength … 2-5
Figure 2-4. Solar Zenith Angle … 2-6
Figure 2-5. Heat Transfer Examples … 2-8
Figure 2-6. Specific Heat Capacity: Water Versus Sand … 2-10
Figure 2-7. Variation of Mean Daily Temperatures for San Francisco (Maritime) and Kansas City (Continental) … 2-11
Figure 2-8. Sounding with an Isothermal Layer … 2-12
Figure 2-9. Sounding with a Temperature Inversion … 2-13
Figure 3-1. The Hydrologic Cycle … 3-1
Figure 3-2. Temperature Effects on Relative Humidity … 3-4
Figure 3-3. Temperature-Dewpoint Spread Effect on Relative Humidity … 3-5
Figure 3-4. Latent Heat Transactions when Water Undergoes Phase Transition … 3-6
Figure 4-1. Earth-Atmosphere Energy Balance … 4-1
Figure 4-2. Greenhouse Effect on Nighttime Radiational Cooling … 4-2
Figure 4-3. Development of a Thermal … 4-3
Figure 4-4. Example of Convection in the Atmosphere … 4-4
Figure 4-5. Solar Zenith Angle Variations with Latitude … 4-5
Figure 4-6. Solar Zenith Angle Variations with Northern Hemisphere Seasons … 4-6
Figure 4-7. Average Seasonal Temperature Variation in the Northern Hemisphere … 4-6
Figure 4-8. Clear Sky Diurnal Temperature and Radiation Variations Over Land … 4-7
Figure 5-1. Air Has Weight … 5-1
Figure 5-2. Aneroid Barometer … 5-2
Figure 5-3. Station Pressure … 5-3
Figure 5-4. Air Pressure in the Standard Atmosphere … 5-4
Figure 5-5. Temperature Effect on Pressure … 5-5
Figure 5-6. Reduction of Station Pressure to Sea Level … 5-5
Figure 5-7. Surface Chart Pressure Patterns … 5-7
Figure 5-8. Weather Balloon and Radiosonde … 5-8
xiii
Figure 5-9. 500 Millibar Constant Pressure Chart … 5-9
Figure 5-10. Density is Mass (Weight) per Volume … 5-10
Figure 5-11. Volume Effects on Density … 5-10
Figure 5-12. Pressure Effects on Density in the Atmosphere … 5-11
Figure 5-13. Temperature Effects on Density … 5-12
Figure 5-14. Water Vapor Effects on Density … 5-12
Figure 5-15. True Versus Indicated Altitude … 5-13
Figure 5-16. Pressure Change Effects on Altimeter Readings … 5-14
Figure 5-17. Temperature Change Effects on Altimeter Readings … 5-15
Figure 5-18. High Density Altitude Effects on Flight … 5-17
Figure 6-1. Weather Observation Sources … 6-1
Figure 6-2. Analysis Procedure Step 1: Determine the Optimal Contour Interval and Values to be Analyzed … 6-3
Figure 6-3. Analysis Procedure Step 2: Draw the Isopleths and Extrema … 6-4
Figure 6-4. Analysis Procedure Step 3: Interpret Significant Weather Features … 6-6
Figure 6-5. Example of a Surface Chart … 6-7
Figure 6-6. Example of a 500 Millibar Constant Pressure Chart … 6-8
Figure 7-1. Direction of Pressure Gradient Force … 7-1
Figure 7-2. Magnitude of Pressure Gradient Force … 7-2
Figure 7-3. Illustration of Coriolis Force … 7-2
Figure 7-4. Coriolis Force Variations Across the Earth … 7-3
Figure 7-5. Coriolis Force Magnitude Variations with Wind Speed … 7-4
Figure 7-6. Friction Force Magnitude Variations with Terrain Roughness … 7-4
Figure 7-7. Friction Force Magnitude Variations with Wind Speed … 7-4
Figure 7-8. Geostrophic Wind … 7-5
Figure 7-9. Upper Air Wind Flow … 7-5
Figure 7-10. Surface Wind Forces … 7-6
Figure 7-11. Surface Wind Flow … 7-6
Figure 8-1. Non-Rotating, Non-Tilted, Waterless, Earth Circulation System … 8-1
Figure 8-2. Earth Circulation System … 8-2
Figure 8-3. Speed Relative to the Earth’s Axis Versus Latitude … 8-3
Figure 8-4. Three Cell Circulations and Jet Stream Location … 8-4
Figure 8-5. Polar and Subtropical Jet Streams … 8-4
xiv
Figure 8-6. Jet Stream Wind Speeds … 8-5
Figure 9-1. Local Wind Circulation … 9-1
Figure 9-2. Sea Breeze … 9-2
Figure 9-3. Sea Breeze Front … 9-3
Figure 9-4. Effects of Coastline Shape on a Sea Breeze … 9-4
Figure 9-5. Land Breeze … 9-5
Figure 9-6. Lake Breeze … 9-6
Figure 9-7. Sea Breeze/Lake Breeze Example … 9-7
Figure 9-8. Valley Breeze … 9-7
Figure 9-9. Mountain-Plains Wind System … 9-8
Figure 9-10. Mountain Breeze … 9-9
Figure 10-1. Air Mass Classification … 10-2
Figure 10-2. Air Mass Modification—Warm, Moist Air Mass Moving Over a Cold Surface … 10-2
Figure 10-3. Lake Effect … 10-3
Figure 10-4. Fronts … 10-4
Figure 10-5. Cold Front … 10-5
Figure 10-6. Warm Front … 10-5
Figure 10-7. Stationary Front … 10-6
Figure 10-8. Occluded Front … 10-6
Figure 10-9. Wave Cyclone Model—Stage 1 … 10-7
Figure 10-10. Wave Cyclone Model—Stage 2 … 10-7
Figure 10-11. Wave Cyclone Model—Stage 3 … 10-8
Figure 10-12. Wave Cyclone Model—Stage 4 … 10-8
Figure 10-13. Wave Cyclone Model—Stage 5 … 10-8
Figure 10-14. Dryline Example … 10-9
Figure 11-1. Unsaturated Ascending/Descending Air Parcel Example … 11-2
Figure 11-2. Ascending Air Parcel that Becomes Saturated Example … 11-3
Figure 11-3. Descending Air Parcel Example … 11-4
Figure 11-4. Orographic Effects Example … 11-5
Figure 11-5. Frictional Effects … 11-6
Figure 11-6. Frontal Lift … 11-7
Figure 12-1. Absolute Stability Example … 12-2
xv
Figure 12-2. Neutral Stability Example … 12-3
Figure 12-3. Absolute Instability Example … 12-4
Figure 12-4. Conditional Instability Example … 12-5
Figure 12-5. Stability Types … 12-6
Figure 12-6. Temperature Lapse Rate Effects on Stability … 12-7
Figure 12-7. Vertical Motion Effects on Stability … 12-8
Figure 12-8. Diurnal Temperature Variation Effects on Stability … 12-9
Figure 12-9. Lifted Index Example … 12-10
Figure 13-1. Cirrus (Ci) … 13-3
Figure 13-2. Cirrocumulus (Cc) … 13-4
Figure 13-3. Cirrostratus (Cs) … 13-5
Figure 13-4. Altocumulus (Ac) … 13-6
Figure 13-5. Altocumulus Standing Lenticular (ACSL) … 13-7
Figure 13-6. Thin Altostratus (As) … 13-8
Figure 13-7. Thick Altostratus (As) or Nimbostratus (Ns) … 13-9
Figure 13-8. Cumulus (Cu) with Little Vertical Development … 13-10
Figure 13-9. Towering Cumulus (TCu) … 13-11
Figure 13-10. Stratocumulus (Sc) … 13-12
Figure 13-11. Stratus (St) … 13-13
Figure 13-12. Stratus Fractus (StFra) and/or Cumulus Fractus (CuFra) of Bad Weather … 13-14
Figure 13-13. Cumulonimbus (Cb) without Anvil … 13-15
Figure 13-14. Cumulonimbus (Cb) with Anvil … 13-16
Figure 14-1. The Collision-Coalescence or Warm Rain Process … 14-2
Figure 14-2. Snow Temperature Environment … 14-3
Figure 14-3. Ice Pellets Temperature Environment … 14-3
Figure 14-4. Freezing Rain Temperature Environment … 14-4
Figure 14-5. Rain Temperature Environment … 14-4
Figure 15-1. Crosswind … 15-1
Figure 16-1. Radiation Fog … 16-1
Figure 16-2. Advection Fog … 16-2
Figure 16-3. Advection Fog Formation … 16-3
Figure 16-4. Frontal Fog Formation … 16-4
Figure 16-5. Haboob … 16-7
xvi
Figure 16-6. Layer Aloft Ceiling Versus Indefinite Ceiling … 16-9
Figure 17-1. Convective Turbulence … 17-2
Figure 17-2. Thermals … 17-2
Figure 17-3. Mechanical Turbulence … 17-3
Figure 17-4. Mountain Waves … 17-4
Figure 17-5. Mountain Wave Clouds … 17-5
Figure 17-6. Wind Shear Turbulence … 17-5
Figure 17-7. Wind Shear Turbulence Associated with a Temperature Inversion … 17-6
Figure 18-1. Icing with Fronts … 18-5
Figure 18-2. Icing with Mountains … 18-6
Figure 19-1. Necessary Ingredients for Thunderstorm Cell Formation … 19-1
Figure 19-2. Thunderstorm Cell Life Cycle … 19-2
Figure 19-3. Multicell Cluster Thunderstorm … 19-3
Figure 19-4. Multicell Line Thunderstorm … 19-4
Figure 19-5. Supercell Thunderstorm … 19-5
Figure 19-6. Factors that Influence Thunderstorm Motion … 19-5
Figure 19-7. Downburst Life Cycle … 19-7
Figure 19-8. Landing in a Microburst … 19-7
Figure 19-9. Thunderstorm with Shelf Cloud … 19-8
Figure 19-10. Vivian, South Dakota Record Hailstone … 19-9
Figure 20-1. Radar Antenna … 20-1
Figure 20-2. Backscattered Energy … 20-2
Figure 20-3. Wavelengths … 20-3
Figure 20-4. Precipitation Attenuation … 20-3
Figure 20-5. Precipitation Attenuation Versus Wavelength … 20-4
Figure 20-6. Beam Resolution … 20-5
Figure 20-7. Beam Resolution Comparison Between WSR-88D and Aircraft Weather Radar … 20-6
Figure 20-8. Normal Refraction … 20-7
Figure 20-9. Subrefraction … 20-8
Figure 20-10. Superrefraction … 20-8
Figure 20-11. Ducting … 20-9
Figure 20-12. Reflectivity Associated with Liquid Targets … 20-10
xvii
Figure 21-1. Mean Worldwide Surface Pressure Distribution and Prevailing Winds Throughout the World in July … 21-2
Figure 21-2. Mean Worldwide Surface Pressure Distribution and Prevailing Winds Throughout the World in January … 21-2
Figure 21-3. A Shear Line and an Induced Trough Caused by a Polar High Pushing into the Subtropics … 21-8
Figure 21-4. A TUTT Moves Eastward Across the Hawaiian Islands. Extensive Cloudiness Develops East of the Trough … 21-9
Figure 21-5. A Northern Hemisphere Easterly Wave Progressing from A–B … 21-10
Figure 21-6. Vertical Cross Section along Line A–B in Figure 21-5 … 21-10
Figure 21-7. The Tracks of Nearly 150 Years of Tropical Cyclones and their Strength Weave Across the Globe … 21-12
Figure 21-8. Radar Image of Hurricane Katrina Observed at New Orleans, Louisiana, on August 29, 2005 … 21-14
Figure 21-9. Hurricane Andrew Observed by Satellite in 1992 … 21-14
Figure 22-1. The Arctic Circle … 22-1
List of Tables Table 1-1. Composition of a Dry Earth’s Atmosphere … 1-1
Table 1-2. Selected Properties of the Standard Atmosphere … 1-6
Table 2-1. Celsius Temperature Conversion Formulae … 2-2
Table 2-2. Fahrenheit Temperature Conversion Formulae … 2-2
Table 2-3. Heat (Thermal) Conductivity of Various Substances … 2-7
Table 2-4. Specific Heat Capacity of Various Substances … 2-9
Table 3-1. Latent Heat of Water at 0 °C … 3-7
Table 5-1. Units of Pressure … 5-3
Table 5-2. Pressure System Symbols … 5-6
Table 5-3. Common Constant Pressure Charts … 5-9
Table 6-1. Common Isopleths … 6-2
Table 6-2. Common Weather Chart Symbols … 6-5
Table 11-1. Air Parcel Vertical Motion Characteristics … 11-4
Table 13-1. Cloud Forms … 13-1
Table 13-2. Approximate Height of Cloud Bases above the Surface … 13-2
Table 19-1. Enhanced Fujita Scale (Enhanced F Scale) for Tornado Damage … 19-11
Table 21-1. Wind Speed and Characteristic House Damage for the
Saffir-Simpson Hurricane Wind Scale … 21-15
Chapter 1. The Earth’s Atmosphere › 1.2 Composition.
CHAPTER 1. THE EARTH’S ATMOSPHERE
1.1 Introduction. The Earth’s atmosphere is a cloud of gas and suspended solids extending from the surface out many thousands of miles, becoming increasingly thinner with distance, but always held by the Earth’s gravitational pull. The atmosphere is made up of layers surrounding the Earth that holds the air we breathe, protects us from outer space, and holds moisture (e.g., vapor, clouds, and precipitation), gases, and tiny particles. In short, the atmosphere is the protective bubble we live in.
This chapter covers our atmosphere’s composition, vertical structure and the standard atmosphere.
1.2 Composition. The Earth’s atmosphere consists of numerous gases (see Table 1-1) with the top four making up 99.998 percent of all gases. Nitrogen, by far the most common, dilutes oxygen and prevents rapid burning at the Earth’s surface. Living things need it to make proteins. Oxygen is used by all living things and is essential for respiration. Plants use carbon dioxide to make oxygen. Carbon dioxide also acts as a blanket and prevents the escape of heat to outer space.
Table 1-1. Composition of a Dry Earth’s Atmosphere
Gas Symbol Content (by Volume)
Nitrogen N2 78.084%
Oxygen O2 20.947%
Argon Ar 0.934%
Carbon Dioxide CO2 0.033%
Neon Ne 18.20 parts per million
Helium He 5.20 parts per million
Methane CH4 1.75 parts per million
Krypton Kr 1.10 parts per million
Sulfur dioxide SO2 1.00 parts per million
Hydrogen H2 0.50 parts per million
Nitrous Oxide N2O 0.50 parts per million
Xenon Xe 0.09 parts per million
1.3 Vertical Structure. › The vertical depth of the troposphere varies due to temperature…
Gas Symbol Content (by Volume)
Ozone O3 0.07 parts per million
Nitrogen dioxide NO2 0.02 parts per million
Iodine I2 0.01 parts per million
Carbon monoxide CO trace
Ammonia NH3 trace
Note: The atmosphere always contains some water vapor in amounts varying from trace to about four percent by volume. As water vapor content increases, the other gases decrease proportionately.
Weather, the state of the atmosphere at any given time and place, strongly influences our daily routine as well as our general life patterns. Virtually all of our activities are affected by weather, but, of all our endeavors, perhaps none more so than aviation.
1.2.1 Air Parcel. An air parcel is an imaginary volume of air to which any or all of the basic properties of atmospheric air may be assigned. A parcel is large enough to contain a very large number of molecules, but small enough so that the properties assigned to it are approximately uniform. It is not given precise numerical definition, but a cubic centimeter of air might fit well into most contexts where air parcels are discussed. In meteorology, an air parcel is used as a tool to describe certain atmospheric processes, and we will refer to air parcels throughout this document.
1.3 Vertical Structure. The Earth’s atmosphere is subdivided into five concentric layers (see Figure 1-1) based on the vertical profile of average air temperature changes, chemical composition, movement, and density. Each of the five layers is topped by a pause, where the maximum changes in thermal characteristics, chemical composition, movement, and density occur.
1.3.1 Troposphere. The troposphere begins at the Earth’s surface and extends up to about 11 kilometers (36,000 feet) high. This is where we live. As the gases in this layer decrease with height, the air becomes thinner. Therefore, the temperature in the troposphere also decreases with height. As you climb higher, the temperature drops from about 15 °C (59 °F) to -56.5 °C (-70 °F). Almost all weather occurs in this region.
The vertical depth of the troposphere varies due to temperature variations which are closely associated with latitude and season. It decreases from the Equator to the poles, and is higher during summer than in winter. At the Equator, it is around 18-20 kilometers (11-12 miles) high, at 50° N and 50° S latitude, 9 kilometers (5.6 miles), and at the poles, 6 kilometers (3.7 miles) high. The transition boundary between the troposphere and the
1.3 Vertical Structure. › Commercial aircraft often cruise in the lower stratosphere to avoid…
layer above is called the tropopause. Both the tropopause and the troposphere are known as the lower atmosphere.
1.3.2 Stratosphere. The stratosphere extends from the tropopause up to 50 kilometers (31 miles) above the Earth’s surface. This layer holds 19 percent of the atmosphere’s gases, but very little water vapor.
Temperature increases with height as radiation is increasingly absorbed by oxygen molecules, leading to the formation of ozone. The temperature rises from an average -56.6 °C (-70 °F) at the tropopause to a maximum of about -3 °C (27 °F) at the stratopause due to this absorption of ultraviolet radiation. The increasing temperature also makes it a calm layer, with movements of the gases being slow.
Commercial aircraft often cruise in the lower stratosphere to avoid atmospheric turbulence and convection in the troposphere. Severe turbulence during the cruise phase of flight can be caused by the convective overshoot of thunderstorms from the troposphere below. The disadvantages of flying in the stratosphere can include increased fuel consumption due to warmer temperatures, increased levels of radiation, and increased concentration of ozone.
1.3 Vertical Structure. › 1.3.3 Mesosphere.
Figure 1-1. Vertical Structure of the Atmosphere
The regions of the stratosphere and the mesosphere, along with the stratopause and mesopause, are called the middle atmosphere. The transition boundary that separates the stratosphere from the mesosphere is called the stratopause.
1.3.3 Mesosphere. The mesosphere extends from the stratopause to about 85 kilometers (53 miles) above the Earth. The gases, including the number of oxygen molecules, continue to become thinner and thinner with height. As such, the effect of the warming by ultraviolet radiation also becomes less and less pronounced, leading to a decrease in temperature with height. On average, temperature decreases from about -3 °C (27 °F) to as low as -100 °C (-148 °F) at the mesopause. However, the gases in the mesosphere
Chapter 1. The Earth’s Atmosphere › Standard atmosphere is a hypothetical vertical distribution of…
are thick enough to slow down meteorites hurtling into the atmosphere where they burn up, leaving fiery trails in the night sky.
1.3.4 Thermosphere. The thermosphere extends from the mesopause to 690 kilometers (430 miles) above the Earth. This layer is known as the upper atmosphere.
The gases of the thermosphere become increasingly thin compared to the mesosphere. As such, only the higher energy ultraviolet and x ray radiation from the sun is absorbed. But because of this absorption, the temperature increases with height and can reach as high as 2,000 °C (3,600 °F) near the top of this layer.
Despite the high temperature, this layer of the atmosphere would still feel very cold to our skin, because of the extremely thin air. The total amount of energy from the very few molecules in this layer is not sufficient enough to heat our skin.
1.3.5 Exosphere. The exosphere is the outermost layer of the atmosphere, and extends from the thermopause to 10,000 kilometers (6,200 miles) above the Earth. In this layer, atoms and molecules escape into space and satellites orbit the Earth. The transition boundary that separates the exosphere from the thermosphere is called the thermopause.
1.4 The Standard Atmosphere. Continuous fluctuations of atmospheric properties create problems for engineers and meteorologists who require a fixed standard for reference. To solve this problem, they defined a standard atmosphere, which represents an average of conditions throughout the atmosphere for all latitudes, seasons, and altitudes.
Standard atmosphere is a hypothetical vertical distribution of atmospheric temperature, pressure, and density that, by international agreement, is taken to be representative of the atmosphere for purposes of pressure altimeter calibrations, aircraft performance calculations, aircraft and missile design, ballistic tables, etc. (see Table 1-2 and Figure 1-2). Weather-related processes are generally referenced to the standard atmosphere, as are examples in this document.
Table 1-2. Selected Properties of the Standard Atmosphere
Property Metric Units English Units
Sea level pressure 1013.25 hectopascals 29.92 inches of mercury
Sea level temperature 15 °C 59 °F
Lapse rate of temperature in the troposphere
6.5 °C/1,000 meters 3.57 °F/1,000 feet
Pressure altitude of the tropopause 11,000 meters 36,089 feet
Temperature at the tropopause -56.5 °C -69.7 °F
Note: 1 hectopascal = 1 millibar.
Figure 1-2. U.S. Standard Atmosphere within the Troposphere
2.5 Temperature. › The Celsius ( C) scale is the most commonly used temperature scale…
CHAPTER 2. HEAT AND TEMPERATURE
2.1 Introduction. Temperature is one of the most basic variables used to describe the state of the atmosphere. We know that air temperature varies with time from one season to the next, between day and night, and even from one hour to the next. Air temperature also varies from one location to another, from high altitudes and latitudes to low altitudes and latitudes. Temperature can be critical to some flight operations. As a foundation for the study of temperature effects on aviation and weather, this chapter describes temperature, temperature measurement, and heat transfer and imbalances.
2.2 Matter. Matter is the substance of which all physical objects are composed. Matter is composed of atoms and molecules, both of which occupy space and have mass. The Earth’s gravity acting on the mass of matter produces weight.
2.3 Energy. Energy is the ability to do work. It can exist in many forms and can be converted from one form to another. For example, if a ball is located at the edge of a slide, it contains some amount of potential energy (energy of position). This potential energy is converted to kinetic energy (energy of motion) when the ball rolls down the slide. Atoms and molecules produce kinetic energy because they are in constant motion. Higher speeds of motion indicate higher levels of kinetic energy.
2.4 Heat. Heat is the total kinetic energy of the atoms and molecules composing a substance. The atoms and molecules in a substance do not all move at the same velocity. Thus, there is actually a range of kinetic energy among the atoms and molecules.
2.5 Temperature. Temperature is a numerical value representing the average kinetic energy of the atoms and molecules within matter. Temperature depends directly on the energy of molecular motion. Higher (warmer) temperatures indicate a higher average kinetic energy of molecular motion due to faster molecular speeds. Lower (colder) temperatures indicate a lower average kinetic energy of molecular motion due to slower molecular speeds. Temperature is an indicator of the internal energy of air.
2.5.1 Temperature Measurement. A thermometer is an instrument used to measure temperature. Higher temperatures correspond to higher molecular energies, while lower temperatures correspond to lower molecular energies.
2.5.2 Temperature Scales. Many scientists use the Kelvin (K) scale, which is a thermodynamic (absolute) temperature scale, where absolute zero, the theoretical absence of all thermal energy, is zero Kelvin (0 K). Thus, the Kelvin scale is a direct measure of the average kinetic molecular activity. Because nothing can be colder than absolute zero, the Kelvin scale contains no negative numbers.
The Celsius (°C) scale is the most commonly used temperature scale worldwide and in meteorology. The scale is approximately based on the freezing point (0 °C) and boiling point of water (100 °C) under a pressure of one standard atmosphere (approximately sea level). Each degree on the Celsius scale is exactly the same size as a degree on the Kelvin scale.
2.5 Temperature. › The United States uses Fahrenheit ( F) scale for everyday temperature…
Table 2-1. Celsius Temperature Conversion Formulae
From Celsius To Celsius
Fahrenheit [°F] = ([°C] x 9/5) + 32 [°C] = ([°F] – 32) x 5/9
Kelvin [K] = [°C] + 273.15 [°C] = [K] – 273.15
For temperature intervals rather than specific temperatures,
1 °C = 274.15 K and 1 °C = 33.8 °F
The United States uses Fahrenheit (°F) scale for everyday temperature measurements. In this scale, the freezing point of water is 32 degrees Fahrenheit (32 °F) and the boiling point is 212 degrees Fahrenheit (212 °F).
Table 2-2. Fahrenheit Temperature Conversion Formulae
From Fahrenheit To Fahrenheit
Celsius [°C] = ([°F] – 32) x 5/9 [°F] = ([°C] x 9/5) + 32
Kelvin [K] = ([°F] + 459.67) x 5/9 [°F] = ([K] x 9/5) – 459.67
For temperature intervals rather than specific temperatures,
1 °F = 255.93 K and 1 °F = -17.22 °C
The heat source for the surface of our planet is the sun. › 2.6.1 Radiation.
Figure 2-1. Comparison of Kelvin, Celsius, and Fahrenheit Temperature Scales
A thermometer changes readings due to the addition or subtraction of heat. Heat and temperature are not the same, but they are related.
2.6 Heat Transfer. Heat transfer is energy transfer as a consequence of temperature difference. When a physical body (e.g., an object or fluid) is at a different temperature than its surroundings or another body, transfer of thermal energy, also known as heat transfer (or heat exchange) occurs in such a way that the body and the surroundings reach thermal equilibrium (balance). Heat transfer always occurs from a hot body to a cold body. Where there is a temperature difference between objects in proximity, heat transfer between them can never be stopped; it can only be slowed down.
The heat source for the surface of our planet is the sun. Energy from the sun is transferred through space and through the Earth’s atmosphere to the Earth’s surface. Since this energy warms the surface and atmosphere, some of it becomes heat energy. There are three ways heat is transferred into and through the atmosphere: radiation, conduction, convection, or any combination of these. Heat transfer associated with the heat change of water from one phase to another (i.e., liquid water releases heat when changed to a vapor, liquid water absorbs heat when it changes to ice) can be fundamentally treated as a variation of convective heat transfer. The heat transfer associated with water will be discussed later.
2.6.1 Radiation. If you have stood in front of a fireplace or near a campfire, you have felt the heat transfer known as radiation. The side of your body nearest the fire warms, while your other side remains unaffected by the heat. Although you are surrounded by air, the air has nothing to do with this type of heat transfer. Heat lamps that keep food warm work in the same way.
All objects emit (radiate) energy as the heat energy within the object… › 2.6.1.1 Solar and Terrestrial Radiation.
Radiation is the transfer of heat energy through space by electromagnetic radiation. These electromagnetic waves travel at the speed of light and are usually described in terms of wavelength or frequency. Frequencies range from gamma rays on the high end to radio waves on the low end. Also contained in the spectrum are x ray, ultraviolet, visible, infrared, and microwave.
Figure 2-2. Radiation Example
All objects emit (radiate) energy as the heat energy within the object is converted to radiation energy. This transmitted radiation passes through entities such as air, water, or space. Along the way, the radiation can be reflected, which occurs when the wave energy changes direction when encountering an object. Eventually, the radiation is absorbed and the electromagnetic wave energy is converted to heat energy by the absorbing object. The emitting object loses heat energy, and the absorbing object gains heat energy during this process.
2.6.1.1 Solar and Terrestrial Radiation. All objects emit radiation energy, including the sun (solar radiation) and the Earth (terrestrial radiation). An object’s wavelength of maximum radiation is inversely related to its temperature; the hotter (colder) the object, the shorter (longer) the wavelength. The sun’s wavelength of maximum radiation is relatively short and is centered in the visible spectrum. The Earth’s wavelength of maximum radiation is relatively long and is centered in the infrared spectrum.
All objects emit (radiate) energy as the heat energy within the object… › Figure 2-4 illustrates the concept.
Figure 2-3. Temperature’s Effect on Radiation Wavelength
Some of the solar radiation that reaches the Earth’s surface is radiated back into the atmosphere to become heat energy. Dark-colored objects such as asphalt absorb more of the radiant energy and warm faster than light-colored objects. Dark objects also radiate their energy faster than light-colored objects.
2.6.1.2 Solar Zenith Angle. The intensity of incoming solar radiation that strikes the Earth’s surface (insolation) varies with solar zenith angle. Solar zenith angle is the angle measured from the Earth’s surface between the sun and the zenith (i.e., directly overhead). Solar zenith angle varies with latitude, season, and the diurnal cycle (sunrise/sunset).
Figure 2-4 illustrates the concept. Insolation is maximized when the solar zenith angle is zero degrees (0°), which means the sun is directly overhead. With increasing solar zenith angle, the insolation is spread over an increasingly larger surface area (y is greater than x) so that the insolation becomes less intense. Also, with increasing solar zenith angle, the sun’s rays must pass through more of the Earth’s atmosphere, where they can be scattered and absorbed before reaching the Earth’s surface. Thus, the sun can heat the surface to a much higher temperature when it is high in the sky, rather than low on the horizon.
The heat source for the surface of our planet is the sun. › Heat (thermal) conductivity is the property of a substance that…
Figure 2-4. Solar Zenith Angle
2.6.2 Conduction. Conduction is the transfer of energy (including heat) by molecular activity from one substance to another in contact, or through, a substance. Heat always flows from the warmer substance to the colder substance. The rate of heat transfer is greater with larger temperature differences and depends directly on the ability of the substance(s) to conduct heat. During conduction, the warmer substance cools and loses heat energy, while the cooler substance warms and gains heat energy.
Heat (thermal) conductivity is the property of a substance that indicates its ability to conduct heat as a consequence of molecular motion. Units are Watts per meter-Kelvin (W m-1 K-1). Table 2-3 below provides the heat (thermal) conductivity of various substances. Note that air is a poor thermal conductor.
The heat source for the surface of our planet is the sun. › 2.6.3 Convection.
Table 2-3. Heat (Thermal) Conductivity of Various Substances
Material Phase Heat (Thermal) Conductivity (W m-1 K-1)
Silver Solid 429
Copper Solid 401
Aluminum Solid 250
Iron Solid 80
Sand (saturated) Solid 2.7
Water (ice) Solid (0 °C) 2.18
Sandstone Solid 1.7
Limestone Solid 1.26 – 1.33
Glass Solid 1.05
Water (liquid) Liquid 0.58
Sand (dry) Solid 0.35
Soil Solid 0.17 – 1.13
Wood (oak) Solid 0.17
Wood (balsa) Solid 0.055
Snow Solid (<0 °C) 0.05 – 0.25
Air Gas 0.024
Water (steam) Gas (125 °C) 0.016
All measurements are at 25 °C unless otherwise noted.
Note: 1 K equals -272.15 °C.
2.6.3 Convection. Convection is the transport of heat within a fluid, such as air or water, via motions of the fluid itself. This type of heat flow takes place in liquids and gases because they can move freely, and it is possible to set up currents within them. Water boiling in a pot is an example of convection. Because air is a poor thermal conductor, convection
Chapter 2. Heat and Temperature › 2.7 Thermal Response.
plays a vital role in the Earth’s atmospheric heat transfer process. Figure 2-5 illustrates examples of various heat transfer processes.
Figure 2-5. Heat Transfer Examples1
2.7 Thermal Response. Whether by radiation, conduction, convection, or a combination of these, the temperature response to the input (or output) of some specified quantity of heat varies from one substance to another. Specific heat capacity, also known simply as specific heat, is defined as the measure of heat energy required to increase the temperature of a unit quantity of a substance by a certain temperature interval. Specific heat capacity is typically expressed in units of joules per gram-Kelvin (J g-1 K-1). Thus, two different substances with identical temperature measurements do not necessarily possess the same amount of heat energy. When exposed to the same amount of heat energy, a substance with a low specific heat capacity warms up more than a substance with a higher specific heat capacity.
1 The source of this and other material labeled COMET® is the Web site at http://meted.ucar.edu/ of the University Corporation for Atmospheric Research (UCAR), sponsored in part through cooperative agreement(s) with the National Oceanic and Atmospheric Administration (NOAA), U.S. Department of Commerce (DOC). ©1997-2015 University Corporation for Atmospheric Research. All Rights Reserved.
Table 2-4. Specific Heat Capacity of Various Substances
Substance Phase Specific Heat Capacity
(J g-1 K-1)
Water (steam) Gas (100 °C) 4.22
Water Liquid (25 °C) 4.18
Wood (balsa) Solid 2.90
Water (ice) Solid (0 °C) 2.05
Wood (oak) Solid 2.00
Soil (wet) Solid 1.48
Sandy clay Solid 1.38
Air (sea level, dry) Gas 1.01
Asphalt Solid 0.92
Clay Solid 0.92
Aluminum Solid 0.91
Brick (common) Solid 0.90
Concrete Solid 0.88
Glass Solid 0.84
Limestone Solid 0.84
Sand (quartz) Solid 0.83
Soil (dry) Solid 0.80
Granite Solid 0.79
Iron Solid 0.46
Copper Solid 0.39
Mercury Liquid 0.14
Lead Solid 0.13
All measurements are at 25 °C unless otherwise noted.
Note: 1 K equals -272.15 °C.
2.7 Thermal Response. › Heat flow differences are another reason why water bodies warm up and…
\Water has the highest specific heat capacity of any naturally occurring substance. That means it has a much higher capacity for storing heat energy than other substances, such as soil, sand, rock, or air. Water can store large amounts of heat energy while only experiencing a small temperature change.
Figure 2-6 below compares the specific heat capacity of water and sand. The specific heat capacity of water is more than five times that of quartz sand. Thus, 4.18 joules of heat are required to raise the temperature of one gram of water by 1 °C, while only 0.83 joules are required to raise the temperature of one gram of quartz sand by 1 °C. This is one reason why beach sand is hotter than water on a sunny, summer afternoon.
Figure 2-6. Specific Heat Capacity: Water Versus Sand
The difference in specific heat capacities is one of the primary reasons why the temperature of a body of water, such as a lake or the ocean, is less variable with time than the surface temperature of land. Water heats up more slowly than land during the day and during summer, and cools down more slowly at night and during the winter. Thus, a body of water exhibits greater resistance to temperature change, called thermal inertia, than does a land mass.
Heat flow differences are another reason why water bodies warm up and cool down more slowly than land. Incoming solar radiation penetrates water to significant depths, but can only heat the top skin layer of soil and rock. Also, since water is a fluid, its heat energy can be circulated through great volumes and depths via convection. Water temperature changes occur to depths of six meters (20 feet) or more on a daily basis, and 200 to 600 meters (650 to 1950 feet) annually. The process is more problematic over land since heat must be transferred via the slow process of conduction. Land temperature changes occur to depths of only 10 centimeters (4 inches) on a daily basis and 15 meters (50 feet) or less annually.
Chapter 2. Heat and Temperature › 2.8 Temperature Variations with Altitude.
Water is much more resistant to temperature changes than land. It warms up and cools down more slowly than land and helps to moderate nearby air temperature. This is why islands and localities located immediately downwind from the ocean or a large lake (maritime locations) exhibit smaller diurnal and seasonal temperature variations than localities well inland (continental locations). Figure 2-7 illustrates this effect. Although both cities are at approximately the same latitude, the temperature is much less variable at San Francisco (maritime) than Kansas City (continental).
Figure 2-7. Variation of Mean Daily Temperatures for San Francisco (Maritime) and
Kansas City (Continental)
2.8 Temperature Variations with Altitude. A lapse rate of temperature is defined as a decrease in temperature with height. In Table 1-2, it was stated that the temperature decreases 6.5 °C/kilometer (3.57 °F/1,000 feet) in the standard atmosphere. But since this is an average, the exact value seldom exists. In fact, temperature in the troposphere sometimes remains constant or even increases with height. Caution should be taken when using the standard lapse rate to estimate the freezing level. Quite often the boundary layer is dry adiabatic and the estimate of freezing level could be in error.
2.8 Temperature Variations with Altitude. › A surface-based inversion typically develops over land on clear nights…
2.8.1 Atmospheric Sounding. An atmospheric sounding, or simply sounding, is a plot of the vertical profile of one or more atmospheric parameters, such as temperature, dewpoint, or wind above a fixed location. Soundings are used extensively by meteorologists to determine the state of the atmosphere.
2.8.2 Isothermal Layer. An isothermal layer is a layer within the atmosphere where the temperature remains constant with height (see Figure 2-8).
Figure 2-8. Sounding with an Isothermal Layer
2.8.3 Temperature Inversion. A temperature inversion, or simply inversion, is a layer in which the temperature increases with altitude. If the base of the inversion is at the surface, it is termed a surface-based inversion. If the base of the inversion is not at the surface, it is termed an inversion aloft (see Figure 2-9).
A surface-based inversion typically develops over land on clear nights when wind is light. The ground radiates and cools much faster than the overlying air. Air in contact with the ground becomes cool, while the temperature a few hundred feet above changes very little. Thus, temperature increases with height.
2.8 Temperature Variations with Altitude. › The principal characteristic of an inversion layer is its marked…
An inversion may also occur at any altitude when conditions are favorable. For example, a current of warm air aloft overrunning cold air near the surface produces an inversion aloft. Inversions are common in the stratosphere.
The principal characteristic of an inversion layer is its marked stability, so that very little turbulence can occur within it. Turbulence will be discussed at length in Chapter 17.
Figure 2-9. Sounding with a Temperature Inversion
Chapter 3. Water Vapor › 3.2 The Hydrologic Cycle.
CHAPTER 3. WATER VAPOR
3.1 Introduction. Water vapor is the gaseous form of water and one of the most important of all constituents of the atmosphere. It constitutes only a small percentage of the Earth’s atmosphere, varying from only trace amounts to 4 percent by volume, and its amount varies widely in space and time. Approximately half of all of the atmospheric water vapor is found below 2 kilometers (6,500 feet) altitude, and only a minute fraction of the total occurs above the tropopause.
Water vapor is important, not only as the raw material for clouds and precipitation (e.g., rain and snow), but also as a vehicle for the transfer of heat energy and as a regulator of the Earth’s temperatures through absorption and emission of radiation, most significantly in the thermal infrared (i.e., the greenhouse effect). The amount of water vapor present in a given air sample may be measured in a number of different ways, involving such concepts as relative humidity and dewpoint. Before we talk about these subjects, we will first discuss how water cycles through the Earth-atmosphere system.
3.2 The Hydrologic Cycle. The hydrologic cycle (see Figure 3-1) involves the continuous circulation of water in the Earth-atmosphere system. Water vapor plays a critical role in the cycle.
Figure 3-1. The Hydrologic Cycle
3.2.1 Evaporation. Evaporation is the phase transition by which a liquid is changed to a vapor (gas). In meteorology, the substance we are concerned about the most is water, and the primary source is the ocean. On average, about 120 centimeters (47 inches) is evaporated into the atmosphere from the ocean each year. For evaporation to take place, energy is required. The energy can come from any source: the sun, the atmosphere, the Earth, or objects on the Earth, such as humans.
3.2 The Hydrologic Cycle. › 3.2.8 Infiltration.
Everyone has experienced evaporation personally. When the body heats up due to the air temperature, or through exercise, the body sweats, secreting water onto the skin. The purpose is to cause the body to use its heat to evaporate the liquid, thereby removing heat and cooling the body. The same effect can be seen when you step out of a shower or swimming pool. The coolness you feel is from the removal of bodily heat used to evaporate the water on your skin.
3.2.2 Transpiration. Transpiration is the evaporation of water from plants. In most plants, transpiration is a passive process largely controlled by the humidity of the atmosphere and the moisture content of the soil. Of the transpired water passing through a plant, only 1 percent is used in the growth process of the plant. The remaining 99 percent is passed into the atmosphere.
3.2.3 Sublimation. Sublimation is the phase transition by which a solid is changed into vapor (a gas) without passing through the liquid phase. In the atmosphere, sublimation of water occurs when ice and snow (solids) change into water vapor (a gas).
3.2.4 Condensation. Condensation is the phase transition by which vapor (a gas) is changed into a liquid. In the atmosphere, condensation may appear as clouds, fog, mist, dew, or frost, depending upon the physical conditions of the atmosphere.
3.2.5 Transportation. Transportation is the movement of solid, liquid, and gaseous water through the atmosphere. Without this movement, the water evaporated over the ocean would not precipitate over land.
3.2.6 Precipitation. Precipitation results when tiny condensation particles grow through collision and coalescence.
3.2.7 Runoff. Runoff occurs when there is excessive precipitation and the ground is saturated (i.e., cannot absorb any more water). This runoff flows into streams and rivers and eventually back into the sea.
Evaporation of this runoff into the atmosphere begins the hydrologic cycle over again. Some of the water percolates into the soil and into the ground water, only to be drawn into plants again for transpiration to take place.
3.2.8 Infiltration. Infiltration is the movement of water into the ground from the surface.
3.4 Relative Humidity. › An air parcel’s capacity to hold water vapor (at a constant pressure)…
3.2.9 Groundwater Flow. Groundwater flow is the flow of water underground in aquifers. The water may return to the surface in springs or eventually seep into the oceans.
3.2.10 Plant Uptake. Plant uptake is water taken from the groundwater flow and soil moisture.
3.3 Saturation. Saturation is the maximum possible quantity of water vapor that an air parcel can hold at any given temperature and pressure. The term saturated air means an air parcel has all the water vapor it can hold, while unsaturated air means an air parcel can hold more water vapor.
3.4 Relative Humidity. Relative humidity is the ratio, usually expressed as a percentage, of water vapor actually in the air parcel compared to the amount of water vapor the air parcel could hold at a particular temperature and pressure.
𝑅𝑅𝑅𝑅𝑅𝑅𝑅𝑅𝑅𝑅𝑅𝑅𝑅𝑅𝑅𝑅 𝐻𝐻𝐻𝐻𝐻𝐻𝐻𝐻𝐻𝐻𝐻𝐻𝐻𝐻𝐻𝐻= 𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊 𝑣𝑣𝑣𝑣𝑣𝑣𝑣𝑣𝑣𝑣 𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐
𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊𝑊 𝑣𝑣𝑣𝑣𝑣𝑣𝑣𝑣𝑣𝑣 𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐𝑐
While relative humidity is the most common method of describing atmospheric moisture, it is also the most misunderstood. Relative humidity can be confusing because it does not indicate the actual water vapor content of the air, but rather how close the air is to saturation. An air parcel with 100 percent relative humidity is saturated, while an air parcel with relative humidity less than 100 percent is unsaturated.
An air parcel’s capacity to hold water vapor (at a constant pressure) is directly related to its temperature. It is possible to change an air parcel’s relative humidity without changing its water vapor content. Figure 3-2 illustrates the concept below. An air parcel at sea level at a temperature of 30 °C has the capacity to hold 27 grams of water vapor. If it actually held 8 grams, its relative humidity would be 30 percent, and it would be unsaturated. However, if the air parcel’s temperature decreases to 20 °C, its water vapor storage capacity decreases to 15 grams and its relative humidity rises to 53 percent. At 10 °C, the air parcel’s water vapor storage capacity decreases to equal the amount of water vapor it actually holds (8 grams), its relative humidity increases to 100 percent, and it becomes saturated. During this cooling process, the air parcel’s actual water vapor content remained constant, but relative humidity increased with decreasing temperature.
Chapter 3. Water Vapor › Surface temperature-dewpoint spread is important in anticipating fog,…
Figure 3-2. Temperature Effects on Relative Humidity
3.5 Dewpoint. Dewpoint is the temperature an air parcel must be cooled at constant pressure and constant water vapor pressure to allow the water vapor in the parcel to condense into water (dew). When this temperature is below 0 °C (32 °F), it is sometimes called the frost point. Lowering an air parcel’s temperature reduces its capacity to hold water vapor.
3.6 Temperature-Dewpoint Spread (Dewpoint Depression). The difference between an air parcel’s temperature and its dewpoint is the dewpoint depression, or commonly referred to as the spread. Surface aviation weather reports (e.g., Aviation Routine Weather Reports (METAR)/Aviation Selected Special Weather Reports (SPECI)) provide observations of both temperature and dewpoint. The temperature greatly affects the air parcel’s ability to hold water vapor, while the dewpoint indicates the actual quantity of water vapor in the parcel. As the spread decreases, relative humidity increases. When the spread decreases to zero, relative humidity is 100 percent, and the air parcel is saturated. Figure 3-3 below illustrates the relationship between temperaturedewpoint spread and relative humidity.
Surface temperature-dewpoint spread is important in anticipating fog, but has little bearing on precipitation. To support precipitation, air must be saturated through thick layers aloft.
Water has some unique thermal properties which make it a powerful heat… › 3.7.1 Latent Heat.
Figure 3-3. Temperature-Dewpoint Spread Effect on Relative Humidity
Relative humidity (RH) depends on the temperature-dewpoint spread. In Figure 3-3, dewpoint is constant but temperature decreases from left to right. On the left panel, relative humidity is 50 percent, which indicates the air parcel could hold twice as much water vapor as is actually present. As the air parcel cools, the temperature-dewpoint spread decreases while relative humidity increases. When the air parcel’s temperature cools to equal its dewpoint (11 °C), its capacity to hold water vapor is reduced to the amount actually present. The temperature-dewpoint spread is zero, relative humidity is 100 percent, and the air parcel is now saturated.
3.7 Change of Phase. Water changes from one state of matter (solid, liquid, or vapor) to another at the temperatures and pressures experienced near the surface of the Earth. Interestingly, water is the only substance on Earth that exists naturally in all three phases: as water droplets and ice crystals (visible as clouds) and as water vapor.
Water has some unique thermal properties which make it a powerful heat transport mechanism. It has the highest specific heat capacity of any naturally occurring substance (see Table 2-4). That means water has a much higher capacity for storing heat energy (with little resulting temperature change) than other substances. These properties make water an ideal heat transport mechanism, and have important implications on weather and climate.
3.7.1 Latent Heat. Latent heat is the quantity of heat energy either released or absorbed by a unit mass of a substance when it undergoes a phase transition (change of state). Units are typically expressed in terms of joules per gram (J/g). Figure 3-4 below illustrates the latent heat transactions that occur when water undergoes phase transition.
Water has some unique thermal properties which make it a powerful heat… › Sublimation is the phase transition by which a solid is changed to a…
Figure 3-4. Latent Heat Transactions when Water Undergoes Phase Transition
Heat is exchanged between water and its environment during phase transition. Although the temperature of the environment changes in response, the temperature of the water undergoing the phase transition remains constant until the phase change is complete; that is, the available heat, latent heat, is involved exclusively in changing the phase of water and not in changing its temperature. There are six phase transitions, three of which are associated with the absorption of latent heat by water from the environment (melting, evaporation, and sublimation), and three of which are associated with the release of heat energy by water to the environment (freezing, condensation, and deposition).
Melting is the phase transition by which a solid is changed to a liquid. During melting, water absorbs 334 joules per gram due to the latent heat of fusion. Freezing, the reverse process, releases 334 joules per gram back to the environment.
Evaporation is the phase transition by which a liquid is changed to a vapor. During evaporation, water absorbs 2,501 joules per gram due to the latent heat of vaporization. Condensation, the reverse process, releases 2,501 Joules per gram back to the environment.
Sublimation is the phase transition by which a solid is changed to a vapor. During sublimation, water absorbs 2,834 joules per gram due to the latent heat of sublimation. Deposition, the reverse process, releases 2,834 joules per gram back to the environment.
Water has some unique thermal properties which make it a powerful heat… › The amount of energy associated with latent heat exchange should not be…
Table 3-1. Latent Heat of Water at 0 °C
Latent Heat Type Energy Exchange
(J/g)
Latent heat of sublimation 2,834
Latent heat of vaporization 2,501
Latent heat of fusion 334
The amount of energy associated with latent heat exchange should not be understated. An average hurricane releases 52 million trillion (5.2 x 1019) joules per day as water vapor condenses into clouds and precipitation. This is equivalent to about 40 times the total worldwide energy consumption per day in 2005!
Chapter 4. Earth-Atmosphere Heat Imbalances › 4.2 The Earth-Atmosphere Energy Balance.
CHAPTER 4. EARTH-ATMOSPHERE HEAT IMBALANCES
4.1 Introduction. Weather is not a capricious act of nature, but rather the atmosphere’s response to unequal rates of radiational heating and cooling across the surface of the Earth and within its atmosphere. The absorption of incoming solar radiation causes heating, while the emission of outgoing terrestrial radiation causes cooling. However, imbalances in the rate of heating and cooling create temperature gradients.2 Atmospheric circulations and weather are the atmosphere’s never-ending attempt to redistribute this heat and achieve equilibrium.
4.2 The Earth-Atmosphere Energy Balance. The Earth-atmosphere energy balance is the balance between incoming energy from the sun (solar radiation) and outgoing energy from the Earth (terrestrial radiation), as seen in Figure 4-1. When solar radiation reaches the Earth, some is reflected back to space by air (8 percent), clouds (17 percent), or the surface (6 percent). Some is absorbed by water vapor/dust/ozone (19 percent) or by clouds (4 percent). The remainder is absorbed by the Earth’s surface (46 percent).
Figure 4-1. Earth-Atmosphere Energy Balance
100 units of incoming radiation from the sun is balanced by 100 units of outgoing radiation from the Earth.
2 A gradient describes the rate of change of a feature (in this case temperature) per unit of distance.
Chapter 4. Earth-Atmosphere Heat Imbalances › Greenhouse warming is enhanced during nights when the sky is overcast…
However, since the Earth is much cooler than the sun, its radiating energy is much weaker (long wavelength) infrared energy. We can indirectly see this energy radiate into the atmosphere as heat (e.g., rising from a hot road, creating shimmers on hot sunny days). The Earth-atmosphere energy balance is achieved as the energy received from the sun (solar radiation) balances the energy lost by the Earth back into space (terrestrial radiation). In this way, the Earth maintains a stable average temperature.
The absorption of infrared radiation trying to escape from the Earth back to space is particularly important to the global energy balance. Energy absorption by the atmosphere stores more energy near its surface than it would if there was no atmosphere. The average surface temperature of the moon, which has no atmosphere, is -18 °C (0 °F). By contrast, the average surface temperature of the Earth is 15 °C (59 °F). This heating effect is called the greenhouse effect.
Greenhouse warming is enhanced during nights when the sky is overcast (see Figure 4-2). Heat energy from the Earth can be trapped by clouds, leading to higher temperatures as compared to nights with clear skies. The air is not allowed to cool as much with overcast skies. Under partly cloudy skies, some heat is allowed to escape, and some remains trapped. Clear skies allow for the most cooling to take place.
Figure 4-2. Greenhouse Effect on Nighttime Radiational Cooling
4.3 Heat Imbalances Between Earth’s Surface and the Atmosphere. › In this manner, convection transports heat from the Earth’s surface…
4.3 Heat Imbalances Between Earth’s Surface and the Atmosphere. The Earth-atmosphere energy balance numbers (see Figure 4-1) indicate that both sensible heat (7 percent) and latent heat (24 percent) processes transfer heat from the Earth’s surface into its atmosphere. Both processes are necessary to prevent the Earth’s surface from continually heating up and the atmosphere from continually cooling down.
4.3.1 Sensible Heating. Sensible heating involves both conduction and convection. It occurs due to differences in air density. Warm air is less dense than cool air.
On warm sunny days, the Earth’s surface is heated by incoming solar radiation or insolation. However, the heating is somewhat uneven because certain areas of the Earth’s surface absorb more heat from the sun than others. Heat is conducted from the relatively warm ground to the cooler overlying air, which warms a shallow layer of air near the ground. The heated air expands, becomes less dense than the surrounding cooler air, and rises. Through this process, a large bubble of warm air called a thermal rises and transfers heat energy upwards (see Figure 4-3). Cooler, denser air sinks toward the ground to replace the rising air. This cooler air becomes heated in turn, rises, and repeats the cycle.
Figure 4-3. Development of a Thermal
In this manner, convection transports heat from the Earth’s surface into the atmosphere. Because air is a poor conductor of heat (see Table 2-3), convection is much more important than conduction as a heat transport mechanism within the atmosphere.
Chapter 4. Earth-Atmosphere Heat Imbalances › 4.4 Heat Imbalance Variations with Latitude.
Figure 4-4. Example of Convection in the Atmosphere
4.3.2 Latent Heat. The phase transition of water and associated latent heat exchanges (see subparagraph 3.7.1) are largely responsible for transferring the excess heat from the surface of the Earth into its atmosphere. As the Earth’s surface absorbs radiation, some of the heat produced is used to evaporate (vaporize) water from oceans, lakes, rivers, soil, and vegetation. The water absorbs heat energy due to the latent heat of vaporization. Some of this water vapor condenses to microscopic water droplets or deposits as ice crystals that are visible as clouds. During cloud formation, the water vapor changes state, and latent heat is released into the atmosphere. During this process, the excess heat is transferred from the Earth’s surface into its atmosphere.
4.4 Heat Imbalance Variations with Latitude. Global imbalances in radiational heating and cooling occur not only vertically between the Earth’s surface and its atmosphere, but also horizontally with latitude. Since the Earth is essentially spherical, parallel beams of incoming solar radiation strike lower latitudes more directly than higher latitudes (see Figure 4-5); that is, the solar zenith angle is lower, and the sun is more directly overhead in equatorial regions than at the poles. At higher latitudes, solar radiation is spread over a larger area and is less intense per unit surface area than at lower latitudes. Thus, the Earth absorbs more solar radiation at lower latitudes than higher latitudes, which creates heat imbalances and temperature gradients between the Equator and the poles.
Chapter 4. Earth-Atmosphere Heat Imbalances › 4.5 Seasons.
Figure 4-5. Solar Zenith Angle Variations with Latitude
The emission of terrestrial radiation also varies by latitude, but less so than the absorption of solar radiation. Terrestrial radiation emission decreases with increasing latitude due to a drop in temperature with latitude. Thus, at higher latitudes, the annual rate of cooling exceeds the rate of warming, while the reverse is true at lower latitudes.
Averaged over all latitudes, incoming solar radiation must equal outgoing terrestrial radiation. Otherwise, the Earth would be unable to maintain a constant average temperature. About 35° latitude in both hemispheres is where incoming and outgoing radiation is equal. This implies there is annual net cooling at higher latitudes and net warming at lower latitudes. However, we know this is untrue. The excess heat in the tropics must be transported polar by some mechanism(s). This poleward heat transport is accomplished by atmospheric circulations, weather, and ocean currents.
4.5 Seasons. Seasons are caused by the tilt of the Earth’s rotational axis as the Earth orbits the sun (see Figure 4-6). The Earth’s rotational axis is tilted by 23½° from the perpendicular drawn to the plane of the Earth’s orbit about the sun and points the same direction in space all year long. The North Pole is tilted most directly toward the sun Solstice (~December 22). Thus, in the Northern Hemisphere, the longest day of the year
Chapter 4. Earth-Atmosphere Heat Imbalances › Figure 4-7 illustrates the average seasonal temperature variation in…
(lowest solar zenith angle) occurs on the Summer Solstice, while the shortest day of the year (highest solar zenith angle) occurs on the Winter Solstice. Day and night are of equal length (12 hours) worldwide on the Vernal Equinox (~March 21) and the Autumnal Equinox (~September 23).
Figure 4-6. Solar Zenith Angle Variations with Northern Hemisphere Seasons
Figure 4-7 illustrates the average seasonal temperature variation in the Northern Hemisphere for both maritime and continental locations. Note that the warmest (coldest days) of the year occur after the summer (winter) solstice. This is due to the time lag necessary for heat flow processes to fully heat (cool) the surface of the Earth.
Figure 4-7. Average Seasonal Temperature Variation in the Northern Hemisphere
Chapter 4. Earth-Atmosphere Heat Imbalances › Shortly after sunrise, incoming solar radiation received at the Earth’s…
4.6 Diurnal Temperature Variation. Diurnal temperature variation is the daytime maximum and nighttime minimum of air temperature due to variations of insolation caused by the rising and setting of the sun (variations of solar zenith angle) as the Earth rotates around its axis. Figure 4-8 depicts the typical diurnal temperature and radiation variations over land when the sky is clear.
Figure 4-8. Clear Sky Diurnal Temperature and Radiation Variations Over Land
Warming and cooling of the Earth depend on an imbalance between solar and terrestrial radiation. The Earth receives heat during the day through incoming solar radiation. It loses heat to space by outgoing terrestrial radiation both day and night.
Shortly after sunrise, incoming solar radiation received at the Earth’s surface (insolation) becomes greater than outgoing terrestrial radiation and the Earth’s surface warms. Peak isolation occurs around noon, but maximum surface air temperature usually occurs during the midafternoon. This lag is necessary for the air near the ground to heat up due to conduction and convection with the surface. The Earth begins to cool once the rate of outgoing terrestrial radiation exceeds the rate of insolation.
Shortly after sunrise, incoming solar radiation received at the Earth’s… › The magnitude of diurnal temperature variation is primarily influenced…
At night, insolation is absent, but outgoing terrestrial radiation continues and the Earth’s surface continues to cool. Cooling continues until shortly after sunrise, when incoming solar radiation once again exceeds outgoing terrestrial radiation. Minimum surface air temperature usually occurs shortly after sunrise.
The magnitude of diurnal temperature variation is primarily influenced by surface type, latitude, sky cover (e.g., clouds or pollutants), water vapor content of the air, and wind speed. Temperature variation is maximized over land, at low latitudes, with a clear sky, dry air, and light wind. Conversely, temperature variation is minimized over water, at high latitudes, with a cloudy sky, moist air, and strong wind.
Chapter 5. Atmospheric Pressure and Altimetry › Atmospheric pressure is the force per unit area exerted by the weight…
CHAPTER 5. ATMOSPHERIC PRESSURE AND ALTIMETRY
5.1 Introduction. Atmospheric pressure is one of the most basic variables used to describe the state of the atmosphere and is commonly reported in weather observations. Unlike temperature and relative humidity, changes in atmospheric pressure are not as readily sensed by people. However, variations of pressure across the Earth are associated with pressure centers (either high pressure centers or low pressure centers) that cause the wind to blow and can bring important weather changes. Density, which is directly related to pressure, is a property of the atmosphere which can be used by pilots to help determine how their aircraft will perform at various altitudes.
This chapter discusses atmospheric pressure, how it is measured, and how it varies across the Earth. This chapter also covers the altimeter, which is a pressure sensor used by pilots to determine altitude. Finally, density will be discussed, along with its relationship to density altitude.
5.2 Atmospheric Pressure. The atoms and molecules that make up the various layers in the atmosphere are always moving in random directions. Despite their tiny size, when they strike a surface they exert pressure.
Each molecule is too small to feel and only exerts a tiny bit of pressure. However, when we add up all the pressures from the large number of molecules that strike a surface each moment, the total pressure is considerable. This is air pressure. As the density of the air increases, then the number of strikes per unit of time and area also increases.
Since molecules move in all directions, they even exert air pressure upwards as they smash into objects from underneath. Air pressure is exerted in all directions.
Atmospheric pressure is the force per unit area exerted by the weight of the atmosphere. Since air is not solid, we cannot weigh it with conventional scales. Yet, three centuries ago, Evangelista Torricelli proved he could weigh the atmosphere by balancing it against a column of mercury. He actually measured pressure converting it directly to weight.
Figure 5-1. Air Has Weight
Air is composed of matter and, thus, has weight due to the pull of Earth’s gravity.
5.2.1 Barometer. The instrument Torricelli designed to measure pressure was called a barometer. The aneroid barometer is the type mostly commonly used by meteorologists and the aviation community.
Atmospheric pressure is the force per unit area exerted by the weight… › 5.2.2 Atmospheric Pressure Units.
Essential features of an aneroid barometer (see Figure 5-2) are a flexible metal cell and the registering mechanism. Air is taken out of the cell to create a partial vacuum. The cell contracts or expands as pressure changes. One end of the cell is fixed, while the other end moves the registering mechanism. The coupling mechanism magnifies the movement of the cell driving an indicator hand along a scale graduated in pressure unit.
Figure 5-2. Aneroid Barometer
5.2.2 Atmospheric Pressure Units. Atmospheric pressure is expressed in many ways throughout the world (see Table 5-1). Meteorologists worldwide have long measured atmospheric pressure in millibars (mb or mbar), which denote pressure as a force per square centimeter. However, after the introduction of the International System of Units (SI) in 1960, the hectopascal (hPa) was adopted by most countries and is used in the Aviation Routine Weather Report (METAR)/Aviation Selected Special Weather Report (SPECI) code first developed in 1968. Many meteorologists prefer to use the term they learned during their education and work experience. Therefore, some continue to use the term millibars, while others use hectopascals (which are equivalent). The unit inch of mercury (inHg or Hg) is still used in the United States for altimetry.
Atmospheric pressure is the force per unit area exerted by the weight… › 5.2.4 Pressure Variation.
Table 5-1. Units of Pressure
Units of Pressure Standard Atmosphere
Value at Sea Level Common Use
Hectopascals (hPa) 1013.2 hPa METAR/SPECI
Millibars (mb or mbar) 1013.2 mb U.S. Weather Charts
Inches of mercury (inHg or Hg) 29.92 inHg U.S. Aviation
Pounds per square inch (psi) 14.7 psi U.S. Engineering
5.2.3 Station Pressure. The pressure measured at an airport is called station pressure, or the actual pressure at field elevation. Pressure is lower at higher altitudes. Therefore, airports with higher field elevations usually have lower pressure than airports with lower field elevations. For instance, station pressure at Denver is less than at New Orleans (see Figure 5-3).
Figure 5-3. Station Pressure
The next few subparagraphs will examine some factors that influence pressure.
5.2.4 Pressure Variation. Atmospheric pressure varies with altitude and the temperature of the air, as well as with other minor influences, such as water vapor.
5.2.4 Pressure Variation. › 5.2.4.2 Temperature Effects on Pressure.
5.2.4.1 Pressure Changes with Altitude. As we move upward through the atmosphere, the weight of the air above us decreases. If we carry a barometer with us, we can measure a decrease in pressure as the weight of the air above us decreases. Figure 5-4 shows the pressure decrease with height in the standard atmosphere.
Figure 5-4. Air Pressure in the Standard Atmosphere
These standard altitudes are based on standard temperatures. In the real atmosphere, temperatures are seldom standard, so we will explore temperature effects on pressure in the following subparagraphs.
5.2.4.2 Temperature Effects on Pressure. Like most substances, air expands as it becomes warmer and contracts as it cools. Figure 5-5 shows three columns of air: one colder than standard, one with standard temperature, and one warmer than standard. Pressure is equal at the bottom and top of each column. Vertical expansion of the warm column has made it taller than the
Atmospheric pressure is the force per unit area exerted by the weight… › Sea level pressure is typically displayed on surface weather charts.
column at standard temperature. Contraction of the cold column has made it shorter than the standard column. Since the total pressure decrease is the same in each column, the rate of decrease of pressure with height in warm air is less than standard, while the rate of decrease in pressure with height in cold air is greater than standard.
Figure 5-5. Temperature Effect on Pressure
5.2.5 Sea Level Pressure. Since pressure varies greatly with altitude, we cannot readily compare station pressures between stations at different altitudes. To make them comparable, we adjust them to some common level. Mean sea level (MSL) is the most useful common reference. In Figure 5-6 pressure measured at a station at a 5,000-foot elevation is 25 inches; pressure increases about 1 inch of mercury for each 1,000 feet, or a total of 5 inches. Sea level pressure is approximately 25 + 5, or 30 inches of mercury.
Figure 5-6. Reduction of Station Pressure to Sea Level
Sea level pressure is typically displayed on surface weather charts. Pressure continually changes across the Earth, so a sequence of surface charts must be viewed to follow these changing pressures.
5.2.5.1 Sea Level Pressure Analyses (Surface Chart). After plotting sea level pressure on a surface chart, lines are drawn connecting points of equal sea level pressure. These lines of equal pressure are isobars. Hence, the surface chart is an isobaric analysis showing identifiable, organized pressure patterns. Four pressure systems are commonly identified: low, high, trough and ridge (see Table 5-2 and Figure 5-7).
Sea level pressure is typically displayed on surface weather charts. › 5.2.5.1 Sea Level Pressure Analyses (Surface Chart).
Table 5-2. Pressure System Symbols
Pressure
System
Symbol Definition
Low
A minimum of atmospheric pressure in two dimensions (closed isobars) on a surface chart, or a minimum of height (closed contours) on a constant pressure chart. Also known as a cyclone.
High
A maximum of atmospheric pressure in two dimensions (closed isobars) on a surface chart, or a maximum of height (closed contours) on a constant pressure chart. Also known as an anticyclone.
Trough An elongated area of relatively low atmospheric pressure.
Ridge
An elongated area of relatively high atmospheric pressure.
5.2.6 Constant Pressure Surface. › 5.2.6.1 Rawinsonde Observations.
Figure 5-7. Surface Chart Pressure Patterns
5.2.6 Constant Pressure Surface. A constant pressure surface is a surface along which the atmospheric pressure is everywhere equal at a given instant. For instance, the 500 millibar constant pressure surface has a pressure of 500 millibars everywhere on it. The height (altitude) of a constant pressure surface varies primarily due to temperature; these heights can be measured by a rawinsonde.
5.2.6.1 Rawinsonde Observations. The National Weather Service (NWS) takes routine scheduled upper air observations, usually referred to as soundings. A balloon carries a rawinsonde instrument (see Figure 5-8), which consists of radio gear and sensing elements. While in flight, the rawinsonde transmits pressure, temperature, and relative humidity data. Wind speed and direction aloft are obtained by tracking the position of the radiosonde in flight using Global Positioning Satellites (GPS). Most stations around the world take rawinsonde observations. However, meteorologists and other data users frequently refer to a rawinsonde observation as a radiosonde observation.
5.2.6 Constant Pressure Surface. › The same concept applies to height contours on an upper air chart,…
Figure 5-8. Weather Balloon and Radiosonde
5.2.6.2 Constant Pressure Surface Analysis (Upper Air Chart). These heights measured by the rawinsonde (and other types of instruments) are plotted on a constant pressure chart and analyzed by drawing a line connecting points of equal height. These lines are called height contours. What is a height contour?
First, consider a topographic map with contours showing variations in elevation. These are height contours of the terrain surface. The Earth’s surface is a fixed reference, and variations in its height are contoured.
The same concept applies to height contours on an upper air chart, except the reference is a constant pressure surface. Varying heights of the pressure surface are contoured. For example, a 700 millibar constant pressure analysis is a contour map of the heights of the 700 millibar pressure surface. While the contour map is based on variations in height, these variations are small when compared to flight levels, and for all practical purposes, one may regard the 700 millibar chart as a weather chart at approximately 3,000 meters (10,000 feet) above MSL.
5.2.6 Constant Pressure Surface. › A contour analysis (see Figure 5-9) shows highs, ridges, lows, and…
A contour analysis (see Figure 5-9) shows highs, ridges, lows, and troughs aloft just as the isobaric analysis shows such systems at the surface. These systems of highs/ridges and lows/troughs are called pressure waves. These pressure waves are very similar to waves seen on bodies of water. They have crests (ridges) and valleys (troughs) and are in constant movement.
Figure 5-9. 500 Millibar Constant Pressure Chart
Table 5-3. Common Constant Pressure Charts
Chart Pressure Altitude (approximate)
Feet (ft) Meters (m)
100 mb 53,000 ft 16,000 m
150 mb 45,000 ft 13,500 m
200 mb 39,000 ft 12,000 m
250 mb 34,000 ft 10,500 m
300 mb 30,000 ft 9,000 m
500 mb 18,000 ft 5,500 m
700 mb 10,000 ft 3,000 m
850 mb 5,000 ft 1,500 m
925 mb 2,500 ft 750 m
5.3 Density. › 5.3.1 Volume Effects on Density.
5.3 Density. Density is the ratio of any quantity to the volume or area it occupies. Atmospheric density is defined as ratio of the mass (or weight) of the air to the volume occupied by it, usually expressed in kilograms per cubic meter (see Figure 5-10).
Figure 5-10. Density is Mass (Weight) per Volume
5.3.1 Volume Effects on Density. The density of an air parcel varies inversely with its volume. Assuming equal mass, an air parcel with a higher density has a smaller volume than an air parcel with a lower density (see Figure 5-11).
Figure 5-11. Volume Effects on Density
5.3 Density. › As we have already seen, air pressure decreases with height in the…
The shorter parcel (that is, the parcel with the smaller volume) has a higher density than the taller parcel which contains the larger volume. This is due to the fact that the air molecules within the shorter parcel must be compressed within the smaller volume.
5.3.2 Changes in Density. In general, the density of an air parcel can be changed by changing its mass, pressure, or temperature. Boyle’s law says that the density of an ideal gas (ρ, the Greek letter rho) is given by:
Where M is the molar mass, P is the pressure, R is the universal gas constant, and T is the absolute temperature.
5.3.3 Density Effects on Pressure. Density is directly related to pressure. Assuming constant mass and temperature, an air parcel with a higher pressure is denser than an air parcel with a lower pressure.
As we have already seen, air pressure decreases with height in the atmosphere. Therefore, the density also decreases with height (see Figure 5-12). In the atmosphere, pressure has the greatest effect on density in the vertical direction.
Figure 5-12. Pressure Effects on Density in the Atmosphere
5.3 Density. › 5.3.5 Water Vapor Effects on Density.
5.3.4 Temperature Effects on Density. Density is inversely related to temperature. Assuming constant mass and pressure, an air parcel with a higher temperature is less dense than an air parcel with a lower temperature (see Figure 5-13). This is because the warmer air occupies a large volume.
Figure 5-13. Temperature Effects on Density
In the atmosphere, temperature has the most effect on density in the horizontal direction; that is, with horizontal changes of location (e.g., New York City versus Miami), temperature has the greatest effect on density.
5.3.5 Water Vapor Effects on Density. Density of an air parcel is inversely related to its quantity of water vapor. Assuming constant pressure, temperature, and volume, air with a greater amount of water vapor is less dense than air with a lesser amount of water vapor. This is because dry air molecules have a larger mass (weight) than water vapor molecules, and density is directly related to mass (see Figure 5-14).
Figure 5-14. Water Vapor Effects on Density
5.4.1 Altitude. › 5.4.1.2 Indicated Altitude.
5.4 Altimetry. The altimeter is essentially an aneroid barometer. The difference is the scale. The altimeter is graduated to read increments of altitude rather than units of pressure. The standard for graduating the altimeter is the standard atmosphere.
5.4.1 Altitude. Altitude seems like a simple term: it means the vertical elevation of an object above the surface of the Earth. But in aviation, it can have many meanings.
5.4.1.1 True Altitude. Since existing conditions in a real atmosphere are seldom standard, altitude indications on the altimeter are seldom actual or true altitudes. True altitude is the actual vertical distance above MSL. If an altimeter does not indicate true altitude, what does it indicate?
5.4.1.2 Indicated Altitude. Figure 5-13 shows the effect of mean temperature on the thickness of three columns of air. Pressures are equal at the bottoms and tops of the three layers. Since an altimeter is essentially an aneroid barometer, altitude indicated by the altimeter at the top of each column would be the same. To see this effect more clearly, see Figure 5-15. In the warm air column, a pilot would fly at an altitude that is higher than the indicated altitude. In the cold air column, the pilot would fly at an altitude lower than the indicated altitude.
Figure 5-15. True Versus Indicated Altitude
Height indicated on the altimeter also changes with changes in surface… › To ensure the altimeter reading is compatible with altimeter readings…
Height indicated on the altimeter also changes with changes in surface pressure. A movable scale on the altimeter permits the pilot to adjust for surface pressure, but he or she has no means of adjusting the altimeter for mean temperature of the column of air below. Indicated altitude is the altitude above MSL indicated on the altimeter when set at the local altimeter setting. But what is altimeter setting?
5.4.1.2.1 Altimeter Setting. Since the altitude scale is adjustable, a pilot can set his or her altimeter to read true altitude at some specified height. Takeoff and landing are the most critical phases of flight; therefore, airport elevation is the most desirable altitude for a true reading of the altimeter. The altimeter setting is the value to which the scale of the pressure altimeter is set so the altimeter indicates true altitude at field elevation.
To ensure the altimeter reading is compatible with altimeter readings of other aircraft in the vicinity, a pilot must ensure the altimeter setting is current. He or she must adjust it frequently while in flight, according to the nearest surface weather reporting station. Figure 5-16 shows the trouble a pilot can encounter if not vigilant in adjusting the altimeter during flight. As he or she flies from high pressure to low pressure, the plane is lower than the altimeter indicates.
Figure 5-16. Pressure Change Effects on Altimeter Readings
5.4.1 Altitude. › 5.4.1.4 Pressure Altitude.
Figure 5-17. Temperature Change Effects on Altimeter Readings
Figure 5-17 shows that as a pilot flies from warm to cold air, the altimeter reads too high—he or she is lower than the altimeter indicates. Over flat terrain, this lower-than-true reading is no great problem; other aircraft in the vicinity also are flying indicated rather than true altitude, and everyone’s altimeter readings are compatible. If flying in cold weather over mountainous areas, however, a pilot must take this difference between indicated and true altitude into account. He or she must know that the true altitude assures clearance of terrain, and compute a correction to indicated altitude.
5.4.1.3 Corrected (Approximately True) Altitude. If a pilot could always determine mean temperature of a column of air between the aircraft and the surface, flight computers would be designed to use this mean temperature in computing true altitude. However, the only guide a pilot has to temperature below him is free air temperature at his altitude. Therefore, the flight computer uses outside air temperature to correct indicated altitude to approximate true altitude. The corrected (approximately true) altitude is indicated altitude corrected for the temperature of the air column below the aircraft, the correction being based on the estimated deviation of the existing temperature from standard atmosphere temperature. It is a close approximation to true altitude and is labeled true altitude on flight computers. It is close enough to true altitude to be used for terrain clearance, provided the pilot has his altimeter set to the value reported from a nearby reporting station.
5.4.1.4 Pressure Altitude. In the standard atmosphere, sea level pressure is 29.92 inches of mercury (1013.2 millibars). Pressure decreases at a fixed rate upward through the standard atmosphere. Therefore, in the standard atmosphere, a given pressure exists at any specified altitude. Pressure altitude is the altitude (above MSL) shown by the altimeter when set to 29.92 inches of mercury. In other words, it is the altitude associated with a specific pressure
Chapter 5. Atmospheric Pressure and Altimetry › The net results are that high density altitude lengthens a pilot’s…
measured by the static port when the altimeter is set to 29.92. Since pressure is the same everywhere regardless of the specific pressure altitude, a constant pressure surface defines a constant pressure altitude. When a pilot flies a constant pressure altitude, he or she is flying a constant pressure surface.
As discussed earlier, constant pressure surfaces have different heights across them. Therefore, when flying at a specific pressure altitude (i.e., constant pressure surface) a pilot’s true altitude will change with distance. However, since pressure altitudes are flown at or above FL180 (in the United States), a pilot will almost always be above the highest terrain features.
5.5 Density Altitude. Density altitude is the pressure altitude corrected for temperature deviations from the standard atmosphere. Density altitude bears the same relation to pressure altitude as true altitude does to indicated altitude.
Density altitude is indirectly related to atmospheric density; as air density increases (decreases), the density altitude decreases (increases). Airports with higher field elevations (e.g., Denver) have lower pressure, lower density, and, therefore, higher density altitudes than airports with lower field elevations (e.g., New Orleans).
Density altitude equals field elevation during standard atmospheric conditions, but conditions are rarely standard. Density altitude is higher (lower) than standard at airports that report lower (higher) than standard pressures (29.92 inches of mercury) and/or higher (lower) than standard temperatures. Temperature is the most important factor since temperature has the greatest effect on density horizontally in the atmosphere. On hot days, the air becomes less dense, causing high density altitudes. On cold days the air is denser, causing lower density altitudes. Dewpoint (water vapor) is also a contributing factor, but its effects are generally negligible.
Density altitude is an index to aircraft performance. Higher (lower) density altitude decreases (increases) performance. High density altitude is a hazard since it reduces aircraft performance in the following three ways:
1. It reduces power because the engine takes in less air to support combustion.
2. It reduces thrust because there is less air for the propeller to work with, or a jet has less mass of gases to force out of the exhaust.
3. It reduces lift because the light air exerts less force on the airfoils.
A pilot cannot detect the effect of high density altitude on his airspeed indicator. The aircraft lifts off, climbs, cruises, glides, and lands at the prescribed indicated airspeeds; but at a specified indicated airspeed, the pilot’s true airspeed and groundspeed increase proportionally as density altitude becomes higher.
The net results are that high density altitude lengthens a pilot’s takeoff, and landing rolls and reduces his or her rate of climb. Before lift-off, the plane must attain a faster groundspeed, and, therefore, needs more runway; and the reduced power and thrust add a need for still more runway. The plane lands at a faster groundspeed and, therefore,
Chapter 5. Atmospheric Pressure and Altimetry › To compute density altitude, a pilot can set the altimeter to 29.92…
needs more room to stop. At a prescribed indicated airspeed, it is flying at a faster true airspeed, and, therefore, covers more distance in a given time, which means climbing at a shallower angle. Adding to this are the problems of reduced power and rate of climb. Figure 5-18 shows the effect of density altitude on takeoff distance and rate of climb.
Figure 5-18. High Density Altitude Effects on Flight
High density altitude also can be a problem at cruising altitude. When air temperature is higher (warmer) than standard atmosphere, the higher density altitude lowers the service ceiling. For example, if temperature at a pressure altitude of 10,000 feet is 20 °C, density altitude is 12,700 feet. A pilot’s aircraft will perform as though it were at 12,700 feet indicated with a normal temperature of -8 °C.
To compute density altitude, a pilot can set the altimeter to 29.92 inches (1013.2 millibars), read the pressure altitude from the altimeter, obtain the outside air temperature, and then use a flight computer to compute density altitude.
Chapter 6. Weather Charts › 6.2 Weather Observation Sources.
CHAPTER 6. WEATHER CHARTS
6.1 Introduction. A weather chart is a map on which data and analyses are presented that describe the state of the atmosphere over a large area at a given moment in time.
The possible variety of such charts is enormous, but in meteorological history there has been a more or less standard set of charts, including surface charts and the constant pressure charts of the upper atmosphere. Because weather systems are three-dimensional (3-D), both surface and upper air charts are needed. Surface weather charts depict weather on a constant-altitude (usually sea level) surface, while upper air charts depict weather on constant-pressure surfaces.
The National Weather Service (NWS) produces many weather charts that support the aviation community. Refer to the current edition of AC 00-45, Aviation Weather Services, for details.
6.2 Weather Observation Sources. Weather analysis charts can be based on observations from a variety of data sources, including:
• Land surface (e.g., automated surface observing system (ASOS), Automated Weather Observing System (AWOS), and mesonet);
• Marine surface (e.g., ship, buoy, Coastal-Marine Automated Network (C-MAN), and tide gauge);
• Sounding (e.g., radiosonde, dropsonde, pibal, profiler, and Doppler weather radar Velocity Azimuth Display (VAD) wind profile);
• Aircraft (e.g., Aircraft Reports (AIREP), Pilot Weather Reports (PIREP), Aircraft Meteorological Data Relay (AMDAR), and Aircraft Communications Addressing and Reporting System (ACARS)); and
• Satellite.
Figure 6-1. Weather Observation Sources
Land Surface Marine Surface Sounding Aircraft Satellite
The weather chart analysis procedure begins with a map of the plotted… › 6.3.1.1 Step 1
6.3 Analysis. Analysis is the drawing and interpretation of the patterns of various elements on a weather chart. It is an essential part of the forecast process. If meteorologists do not know what is currently occurring, it is nearly impossible to predict what will happen in the future. Computers have been able to analyze weather charts for many years and are commonly used in the process. However, computers cannot interpret what they analyze. Thus, many meteorologists still perform a subjective analysis of weather charts when needed.
6.3.1 Analysis Procedure. The analysis procedure is similar to drawing in a dot-to-dot coloring book. Just as one would draw a line from one dot to the next, analyzing weather charts is similar in that lines of equal values, or isopleths, are drawn between dots representing various elements of the atmosphere. An isopleth is a broad term for any line on a weather map connecting points with equal values of a particular atmospheric variable.
Table 6-1. Common Isopleths
Isopleth Variable Definition
Isobar Pressure A line connecting points of equal or constant pressure.
Contour Line (also called isoheight)
Height A line of constant elevation above MSL of a defined surface, typically a constant pressure surface.
Isotherm Temperature A line connecting points of equal or constant temperature.
Isotach Wind Speed A line connecting points of equal wind speed.
Isohume Humidity A line drawn through points of equal humidity.
Isodrosotherm Dewpoint A line connecting points of equal dewpoint.
The weather chart analysis procedure begins with a map of the plotted data which is to be analyzed (see Figure 6-2). It is assumed that bad or obviously incorrect data has been removed before beginning the analysis process. At first, the chart will appear to be a big jumble of numbers. But when the analysis procedure is complete, patterns will appear, and significant weather features will be revealed.
6.3.1.1 Step 1: Determine the Optimal Contour Interval and Values to be Analyzed. The first step in the weather chart analysis procedure is to identify the maxima and minima data values and their ranges to determine the optimal contour interval and values to be analyzed. The best contour interval will contain enough contours to identify significant weather features, but not so many that the chart becomes cluttered. Each weather element has a standard contour interval on NWS weather charts, but these values can be adjusted in other analyses as necessary.
The weather chart analysis procedure begins with a map of the plotted… › When drawing isopleths and extrema on a weather chart, certain rules…
Figure 6-2. Analysis Procedure Step 1: Determine the Optimal Contour Interval and
Values to be Analyzed
Every contour value must be evenly divisible by the contour interval. So, for example, if the contour interval is every 4 units, a 40-unit contour is all right, but a 41-unit contour is not. In the surface pressure analysis example shown in Figure 6-2, we will perform an isobar analysis beginning at a value of 992 millibars and use a contour interval of 4 millibars, which is standard on the NWS Surface Analysis Chart.
6.3.1.2 Step 2: Draw the Isopleths and Extrema. The second step is to draw the isopleths and extrema (maxima and minima) using the beginning contour value and contour interval chosen in the first step. It is usually easiest to begin drawing an isopleth either at the edge of the data domain (edge of the chart), or at a data point that matches the isopleth value being drawn. Interpolation must often be used to draw isopleths between data points and determine the extrema. Interpolate means to estimate a value within an interval between known values.
When drawing isopleths and extrema on a weather chart, certain rules must be followed:
• The analysis must remain within the data domain. Analysis must never be drawn beyond the edge of the chart where there are no data points. That would be guessing.
• Isopleths must not contain waves and kinks between two data points. This would indicate a feature too small to be supported by the data. Isopleths should be smooth and drawn generally parallel to each other.
• When an isopleth is complete, all data values must be higher than the isopleth’s value on one side of the line and lower on the other.
• A closed loop isopleth must contain an embedded extremum (maximum or minimum).
• When a maximum (minimum) is identified, data values must decrease (increase) in all directions away from it.
• Isopleths can never overlap, intersect, or cross over extrema. It is impossible for one location to have more than one data value simultaneously.
Continue reading ↓ 120 of 407 passages shown