Radar Vectors
FAA Order Cancelled Issued Sep 28, 2009 AJW-331 126 pages Copy saved Nov 18, 2026

Order 8240.36M Flight Inspection Report Processing System (with Change 1 Incorporated)

This document is cancelled. Cancelled by 8240.36N. Check the official source before relying on it.

Official source ↗ Open PDF

Text read by OCR from a scanned file (9 of 126 pages). Check the original, as some words may be misread.

Change 1 Cover

Distribution: Special Addressees Initiated By: Aviation System Standards Flight Inspection Operations Flight Inspection Policy (AJW-331)

CHANGE U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION Change 1 to

8240.36M

5/30/11

SUBJ: Flight Inspection Report Processing System (FIRPS) 1. Purpose of This Change. This Change provides interim guidance to FAA Order 8240.36M, Flight Inspection Report Processing System (FIRPS). 2. Audience. Air Traffic Technical Operations Eastern, Central, and Western Service Areas; Aviation System Standards Flight Inspection Operations Group Offices and crewmembers; Air Force Flight Standards Agency (AFFSA); the 1st Air Force Reserves Unit; and users of FAA Order 8240.36. 3. Where Can I Find This Change? Go to the Directives Management System (DMS) website: https://employees.faa.gov/tools_resources/orders_notices/index.cfm/go/document.list or to the AVN website: http://www.faa.gov/air_traffic/flight_info/avn/flightinspection/onlineinformation/8200/. 4. Cancellation. N 8200.122, Changes to FAA Order 8240.36M, Flight Inspection Report Processing System, dated September 20, 2010, is canceled. 5. Explanation of Policy Change. This Change clarifies examples when entering data on a report, corrects reference locations, and updates report forms to match dated form currently used in FIRPS automated forms application. Incorrect paragraph references updated throughout order.

a. Chapter 2:

(1) Paragraph 12a(8). Changes provide a standardized approach to the codes used in the Flight Operations Management System (FOMS), Flight Management/ Daily Flight Log (FM DFL), and the Flight Inspection Report Processing System (FIRPS). The unsatisfactory (CU, RU, SU) options are being added to the drop-down boxes on the Report Search and Worklist item pages. The Inspection Type codes for the drop-down list on the reports are being changed to match what is entered on the DFL to provide uniformity throughout the process.

(2) Paragraphs 12b(4) and (5), Reversed the order of (4) and (5) and changed title to “Additional Crew Member” to match fields on the form.

8240.36M 5/30/11 Chg 1

b. Chapter 3:

(1) Paragraph 21. Added instructions for using FAA Form 8240-1.

(2) Paragraph 21f. Changed to clarify use of “lighting systems” block and what remarks to make concerning lighting systems that support lower approach minima.

(3) Paragraph 21i. “NDB” added to lead-in title. VOR example changed and ESV DME guidance clarified. Changed Example to “VOR/ R-090/ 45.0nm/ 16,000 ft Revalidation, SAT”. Added, “Each component will have its own ESV entry. When DME is included in the ESV, it will be listed separately, ‘DME/ R-090/ 45.0 nm/ 16,000 ft Revalidation, SAT’ “.

c. Appendix 1. Added FAA Form 8240-4, FI Report – GBAS, to forms listing.

d. Appendix 2:

(1) Paragraph 5. Changed reference for form completion to “Appendix 20”.

(2) Paragraph 5b. Clarified identification feature for commissioning a VOT.

(3) Paragraph 5f(4). Updated reference to form number.

(4) Paragraph 6a. Deleted REF DATE sentence. Moved the information to Paragraph 6b(4) and renumbered it to be Paragraph 6c.

e. Appendix 4. FAA Form 8240-4, Flight Inspection Report—Ground-Based Augmentation System (GBAS), and instructions for completion added.

f. Appendix 5:

(1) Page A5-1, 3rd paragraph. Changed and clarified directions for reporting on lights and lighting aids.

(2) Appendix 5, Paragraph 3f. Changed reference FROM “Chapter 2, Paragraph 12m” TO “Chapter 2, Paragraph 12c”. Clarified directions on reporting facility status for lights and VGSI systems.

(3) Appendix 5, Paragraph 5b. Changed instructions for making remarks on visual aids.

(4) Appendix 5, Paragraphs 6a and c. Drop-down menu item references clarified.

(5) Appendix 5, Paragraph 6c(3)(d). Changed example in 3rdd sentence FROM “For a 4-box system, enter only the angles of Box 2 and Box 3” TO “For a 4-Box system, Box 2 and Box 3 angles required; Box 1 and Box 4 may be reported when measured.”

g. Appendix 6. FAA Form 8240-6, Flight Inspection Report—Precision Approach Radar, dated 7-2005 replaced by form dated 7-2006.

5/30/11 8240.36M Chg 1

h. Appendix 7:

(1) Paragraph 1. Incorrect paragraph references updated.

(2) FAA Form 8240-7, Flight Inspection Report—ILS Worksheet dated 4/2000 replaced by form dated 7-2005.

i. Appendix 8, Paragraph 6h. Changed paragraph for compliance with Policy Memo dated February 18, 2010, Reporting Localizer Clearances. Subject Policy Memo is thus canceled.

j. Appendix 12, Paragraph 3b. Changed ground equipment type examples in the 2nd and 3rd sentences FROM “ASR/9" or "ASR/8” TO “ASR-9” or “ASR-8.” The examples now match how the facilities are entered on the facility data sheets and eliminate a QC question.

k. Appendix 14. Paragraph 3. Incorrect paragraph reference updated.

l. Appendix 17. FAA Form 8240-17, Flight Inspection Report—RNAV replaced so that the current FIRPS form and FAA Order 8240.36M match.

m. Appendix 20, 2nd paragraph. Removed 1st sentence and replaced with, “This form, when required, must be sent to ‘NFDC/ AeroNav Support Specialist (AJV-213)’ via the following email: ‘9-AMC-AVN-DATACHANGE’. Include facility ID, facility type, and state or country code in the subject line of the email message.” FAA Forms 8240-20-1 and 2 changed to reflect email address change. Reference to “AVN” in 4th sentence changed to “AVNIS”.

n. Appendix 21. FAA Form 8240-21, Flight Inspection Report—Controlling Obstacle Evaluations, replaced so that current FIRPS form and Order 8240.36M match.

6. Disposal of Transmittal. After filing the revised pages, the change transmittal should be retained.

PAGE CONTROL CHART

REMOVE PAGES DATED INSERT PAGES DATED

iii and iv 9/28/09 iii and iv 5/30/11 5 9/28/09 5 9/28/09 6 9/28/09 6 5/30/11 9 and 10 9/28/09 9 and 10 5/30/11 15 thru 17 and 18 9/28/09 15 thru 19 (and 20) 5/30/11 A1-1 9/28/09 A1-1 5/30/11 A1-2 9/28/09 A1-2 9/28/09 A2-1 thru 4 9/28/09 A2-1 thru 4 5/30/11

8240.36M Chg 1

5/30/11

PAGE CONTROL CHART (continued)

REMOVE PAGES

DATED

INSERT PAGES

DATED

Appendices 3 -4 (Reserved)

A5-1 and 2 A5-3 A5-4 A6-5 thru A6-7 (and 8) A7-1 A7-2 A7-5 and A7-6 A8-3 A8-4 A12-1 A12-2 A14-1 A14-2 A17-3 A17-4 A20-1 A20-2 and 3 A20-4 and 5 (and 6) A21-1 A21-2

Edward W. Lucke, Jr.

9/28/09

9/28/09 9/28/09 9/28/09 9/28/09 9/28/09 9/28/09 9/28/09 9/28/09 9/28/09 9/28/09 9/28/09 9/28/09 9/28/09 9/28/09 9/28/09 9/28/09 9/28/09 9/28/09 9/28/09 9/28/09

Appendix 3 (Reserved) A4-1 thru A4-7 (and 8) A5-1 and 2 A5-3 A5-4 A6-5 thru A6-7 (and 8) A7-1 A7-2 A7-5 and A7-6 A8-3 A8-4 A12-1 A12-2 A14-1 A14-2 A17-3 A17-4 A20-1 A20-2 and 3 A20-4 and 5 (and 6) A21-1 A21-2

5/30/11 5/30/11 5/30/11 9/28/09 5/30/11 5/30/11 5/30/11 9/28/09 5/30/11 9/28/09 5/30/11 5/30/11 9/28/09 9/28/09 5/30/11 9/28/09 5/30/11 5/30/11 9/28/09 5/30/11 9/28/09 5/30/11

Acting Director of Aviation System Standards

U.S. DEPARTMENTOF TRANSPORTATION FEDERAL FEDERAL AVIATION ADMINISTRATION National Policy ORDER

Cover

8240.36M

Effective Date: 9/28/09 SUBJ: Flight Inspection Report Processing System(FIRPS)

This order provides policy, guidance, and distribution requirements for flight inspection reports and records when using the electronic Flight Inspection Report Processing System (FIRPS).

Flight inspection files (e.g., flight inspection reports, data sheets, oscillographic recordings, electronic media, photographs, correspondence) are federal records. Unless classified by specific authority, they are available, on request, to the public by the authority of the Freedom of Information Act, Title 5, United States Code, Section 552. The policy and legal requirements for records management are contained in other Federal Aviation Administration (FAA) orders.

Guidelines for record disposition are contained in FAA Order 1350.15, Records Organization, Transfer, and Destruction Standards.

Thomas C. Accardi Director of Aviation System Standards

Distribution: Initiated By:Air Traffic Technical Operations AJW-C/E/W/33/32; AFFSA; 1ASF Aviation System Standards Flight Inspection Policy (AJW-331)

This Page Intentionally Left Blank

5/30/11 8240.36M Chg 1

iii

Table of Contents Chapter 1. Introduction

1. Purpose of This Order … 1 2. Audience … 1 3. Where Can I Find This Order? … 1 4. What This Order Cancels … 1 5. Explanation of Policy Changes … 1 6. Computer Generated Forms … 3 7. Definitions, Acronyms, and Abbreviations … 4 8. Information Currency … 4 9 – 10 Reserved … 4 Chapter 2. General Information

TOC

11. General Forms Completion … 5 12. Common Report Data … 7 13. Corrected Copies of Reports … 11 14. Security Classification of Flight Inspection Reports … 11 15. Distribution of Reports and Recordings … 12 16 – 20 Reserved … 14 Chapter 3. Required Report Remarks

21. Remarks Field … 15 22 – 25 Reserved … 19 Appendix 1. Flight Inspection Forms … A1-1

Flight Inspection Report – Continuation Sheet, FAA Form 8240-1 … A1-3 Appendix 2. Flight Inspection Report – VOR, VOR/ DME, VORTAC, TACAN, VOT ... A2-1

FAA Form 8240-2 … A2-8 Appendix 3 (Reserved) Appendix 4. Flight Inspection Report—Ground-Based Augmentation System (GBAS) .... A4-1

FAA Form 8240-4 … A4-3 Appendix 5. Flight Inspection Report – Non-Directional Beacon,

Direction Finding, Visual Aids, Communications … A5-1 FAA Form 8240-5 … A5-5 Appendix 6. Flight Inspection Report – Precision Approach Radar ,

GPN-22/ TPN-25 Continuation Sheet, PAR TPN-22 Continuation Sheet … A6-1 PAR, FAA Form 8240-6 … A6-5 PAR GPN-22/ TPN-25 Continuation Sheet … A6-6 PAR Continuation Sheet … A6-7

8240.36M 5/30/11 Chg 1

iv

Table of Contents

continued Appendix 7. Flight Inspection Report – ILS Worksheet and ILS Continuation Worksheet A7-1

ILS Worksheet, FAA Form 8240-7 … A7-5 ILS Continuation Worksheet, FAA Form 8240-7-1 … A7-6 Appendix 8. Flight Inspection Report – Instrument Landing System (ILS) … A8-1

FAA Form 8240-8 … A8-11 Appendices 9 - 10 (Reserved) Appendix 11. Flight Inspection Report – ILS/ MLS Maintenance Alert … A11-1

FAA Form 8240-11 … A11-2 Appendix 12. Flight Inspection Report – Surveillance Radar … A12-1

FAA Form 8240-12 … A12-5 Appendix 13. Flight Inspection Report – General Characteristics … A13-1

FAA Form 8240-13 … A13-2 Appendix 14. Flight Inspection Report – After Accident Continuation Sheet … A14-1

FAA Form 8240-14 … A14-4 Appendix 15. (Reserved) Appendix 16. Flight Inspection Report – Microwave Landing System (MLS) and MLS Commissioning Data Words … A16-1

FAA Form 8240-16 … A16-5 Appendix 17. Flight Inspection Report – RNAV … A17-1

FAA Form 8240-17 … A17-4 Appendices 18 - 19 (Reserved) Appendix 20. Flight Inspection Report – AVNIS Data Change Submission … A20-1

FAA Form 8240-20-1 … A20-4 FAA Form 8240-20-2 … A20-5 Appendix 21. Flight Inspection Report – Controlling Obstacle Evaluation … A21-1

FAA Form 8240-21 … A21-2

9/28/09 8240.36M

Chapter 1. Introduction 1. Purpose of This Order. This order provides policy, guidance, and distribution requirements for flight inspection reports and records when using the electronic Flight Inspection Report Processing System (FIRPS). 2. Audience. The audience for this order is the Air Traffic Technical Operations, Eastern, Central and Western Service Areas; the Aeronautical Data Support Team, Flight Inspection Operations offices and crewmembers in Aviation System Standards; and special military addressees. 3. Where Can I Find This Order? Go to the Directives Management System (DMS) website: https://employees.faa.gov/tools_resources/orders_notices/ or to the AVN website: http://www.avn.faa.gov/index.asp?xml=fioo/faa8240orders 4. What This Order Cancels. This order cancels FAA Order 8240.36L, dated October 1, 2006. It also cancels the following Notices:

Chapter 1 - Intro

a. Notice 8200.100, FAA Order 8240.36L, Flight Inspection Report Processing System, dated October 1, 2006

b. Notice 8200.104, FAA Order 8240.36L, Flight Inspection Report Processing System (Chapters 2 and 3; Appendices 2, 6, 8, 14, and 17), dated September 5, 2007

c. Notice 8200.105, FAA Order 8240.36L, Flight Inspection Report Processing System (Chapter 2, Appendices 2 and 17), dated October 1, 2007

d. Notice 8200.110, Pen and Ink Change to Appendix 8 of FAA Order 8240.36L, Flight Inspection Report Processing System, dated July 25, 2008

e. Notice 8200.111, FAA Order 8240.36L, After Accident Report, dated March 20, 2009. 5. Explanation of Policy Changes

a. General. In the interest of efficient and effective employment of resources, a change to the flight inspection reports completion process will be implemented. This change will reduce the time and effort presently required for reports completion and processing.

b. Chapter 2:

(1) Paragraph 11a. Redefined report completion responsibility (added Mission Specialist) and eliminated reports completion requirements for inspections not requiring a report. The results of the flight inspection of the select facilities/ procedures must be documented IAW the Daily Flight Log (DFL). This, along with signing the Procedure Package paperwork, when applicable, will satisfy the reporting requirement.

(2) Paragraph 11m. Moved guidance that was located at Paragraph 15f to this location.

8240.36M 9/28/09

(3) Paragraph 12d(5). Added guidance for if a facility identifier is changed.

(4) Paragraph 12d(6). Removed the guidance. The information was provided for the Technical Services Sub-Team but is no longer required here. It has been included in FAA Order 8240.52, Aeronautical Data Management.

(5) Paragraph 12e, Table. Expanded owner code description for “State”.

(6) Paragraph 12h. Deleted 4th sentence and added 5th sentence containing instructions for routes or stand-alone point-in-space fix.

(7) Paragraph 12i. The signatory responsibilities have been modified.. The pilot in command must review all reports and enter his /her crew number on the report.

(8) Paragraph 15b. After Accident (AA) Reports paragraph replaced.

(9) Paragraph 15f. Moved the guidance that was located here to Paragraph 11m.

c. Chapter 3:

(1) Paragraph 21g. Incorporated guidance issued by Notice N 8200.100, FAA Order 8240.36L, Flight Inspection Reporting Processing System.

(2) Paragraph 21l. Removed the guidance. The information was provided for the Technical Services Sub-Team (Data Management) but is no longer required.

(3) Paragraph 21p, second sentence. Changed the word “region” to “service area”.

d. Appendix 1. Corrected Flight Inspection Report-VOR, VOR/ DME, VORTAC, TACAN ORBITAL data form number from “8240-4” to “8240-2”.

e. Appendix 2:

(1) Paragraph e(5)c. VOT inspection authorization changed from Technical Services Sub-Team to Flight Inspection Policy.

(2) Added Paragraph e(6), Transmitter Changes when Conducting an alignment orbit.

(3) Paragraph g(10), second sentence. Removed requirement to report AFIS distance to the nearest mile and changed example.

f. Appendix 6. Paragraph 4a(2), last sentence. Deleted this sentence. We provide guidance at the beginning of the paragraph that this field is not filled out when inspecting a computer generated PAR.

g. Appendix 8:

(1) Paragraph 3r(2), second sentence. Corrected 2 paragraph references that were wrong.

(2) Paragraph 5c. Corrected typos.

(3) Paragraph 6a. Expanded instructions for ILS-1 Altitude reporting.

9/28/09 8240.36M

(4) Paragraph 7a. Expanded instructions for ILS-2 Altitude reporting.

(5) Paragraph 10c. Guidance for sideband reference glide slope reporting added.

(6) Paragraph 10g. Guidance for entering amount of attenuation added.

(7) Paragraph 10h. Guidance for entering amount of attenuation added.

h. Appendix 14:

(1) Paragraph 3, Special Report Review, replaced.

(2) Paragraph 5a(6), Aircraft Type & Number, replaced.

i. Appendix 17:

(1) Paragraph 1, first sentence was deleted. The requirements are explained in Chapter 2, General Forms Completion.

(2) Paragraph 1a. Changed 1st sentence to include instructions for reporting an approach. Changed 4th sentence for clarity regarding reporting instructions for stand-alone point-inspace fix.

(3) Paragraph 1b. Clarified reporting instructions for “Location”.

(4) Paragraph 1d. Changed Control Number instructions to read, “leave blank”.

(5) Paragraph 3b. Added stand-alone point-in-space fix reporting instructions..

(6) Paragraph 3l. Guidance for VNAV reporting clarified.

(7) Paragraph 5. Last sentence. Corrected typo.

(8) Paragraph 6a(1), 1st sentence. Added instructions for step down fix.

(9) Paragraph 6a(3). Added stand-alone point-in-space fix reporting instructions.

j. Appendix 20. Flight Inspection Report—AVNIS Data Change Submission, FAA Form 8240-20, added.

k. Appendix 21. First sentence deleted. The requirements are explained in Chapter 2, General Forms Completion. 6. Computer-Generated Forms. This paragraph provides information on the automation of the flight inspection forms.

a. Implementation. The automated system will expedite flight inspection reporting by reducing the number of errors from manual entries. The system also allows information to be auto-filled from sources such as the Daily Flight Log (DFL), itinerary, and AIRNAV database.

8240.36M 9/28/09

b. Use of Automated Forms. The software package will provide an automated method for completing flight inspection forms. The automated process allows each user to fill in forms, forward the report for crew review, quality control, and archive via system networks.

c. Equipment Requirements. Each user office must have access to the appropriate hardware/ software package. The required software, as well as a user’s guide for the current form software package, may be obtained from the Information Technology Staff.

d. System Description. This electronic form processor has a visual interface and allows each user to work with forms using windows, pictures, and menus on a screen. The completed screen data and form may be printed on bond paper.

e. Some Features of the System. This program allows the user to:

(1) Bring a copy of the form into the work area on a screen.

(2) Tab or select particular fields on the forms with a mouse and type in required data.

(3) Automatically fill in areas on the form by the computer using many designated fields that contain relatively constant facility data.

(4) Fill in forms completely and accurately with many automatic checks and entries.

(5) Fill forms with information from central databases.

(6) Print forms efficiently.

f. Appendix 1, Flight Inspection Forms, contains a listing of forms used in reporting various facilities and types of inspections.

7. Definitions, Acronyms, and Abbreviations. (Refer to Order 8200.1, United States Standard Flight Inspection Manual.) This order contains instructions and guidance material. Directive verbs are used. In this order, the words:

a. Must in the second or third person means that an action is mandatory; "must not" means that an action is prohibited.

b. Will indicates it is understood that an action is to be taken. Do not use "will" when you mean "must."

c. Should means that an action is desirable but not mandatory or, "We would like you to do it, but you don't have to."

d. May means an action is permissive - or "If you want to, go ahead." 8. Information Currency. Comments regarding corrections, clarification, or suggested improvements regarding the content of this order should be forwarded to Flight Inspection Policy, AJW-331, on FAA Form 1320-19, Directive Feedback Information. If an interpretation is urgently needed, you may call the Flight Inspection Operations Group, 405-954-3766, during duty hours. 9 - 10. Reserved.

Chapter 2 - Gen Info

9/28/09 8240.36M

Chapter 2. General Information 11. General Forms Completion

a. Reports. The Flight Inspector or Mission Specialist is responsible for initiating reports for all flight inspections requiring a report.

b. Reporting Numeric Data. Unless otherwise stated, report numerical data to the following accuracy:

(1) Microamperes - To the nearest whole microampere.

(2) Altitude - To the nearest foot, mean sea level (MSL).

(3) Azimuth - To the nearest tenth of a degree.

(4) Percent - To the nearest tenth of a percent.

(5) Mileage - To the nearest tenth of a nautical mile.

(6) Angles - To the nearest hundredth of a degree.

(7) Widths - To the nearest hundredth of a degree.

(8) Latitude – Degrees, minutes, seconds, and hundredths of a second (north/ south).

(9) Longitude – Degrees, minutes, seconds, and hundredths of a second (east/ west).

Note: In accordance with FAA Order 8200.1, United States Standard Flight Inspection Manual, Formulas, the following guidelines must be used in rounding off computations. Measurements and calculations should be carried to one decimal place more than that required for tolerance application. Then apply the following criteria to round off a measurement.

Numerals 1 to 5, round off to zero.

Numerals 6 to 9, round off to the next higher value.

Example: Glidepath Course Width: 0.755 = 0.75

0.756 = 0.76

Exception: If a measurement exceeds a tolerance, it must not be rounded off to an in tolerance condition.

Example: Glidepath Course Width - 0.903 is out of tolerance.

c. Primary and Supplementary Report Forms. The current software for automated form completion must be used. The forms may be filled out by hand only when an interim report is required. Use black ink for data entry.

8240.36M 5/30/11 Chg 1

d. Non-Applicable Portions of Report Forms. If any part of a report form does not apply to the facility inspected or the type inspection conducted, leave it blank. Automated forms have pages that are not always required to complete a report; pages not used when a report is completed may be deleted.

e. Type Inspection. Except for the special checks which meet periodic requirements, IAW Chapter 3, Paragraph 21m, report only one type of inspection per report form (i.e., if a periodic inspection is conducted on one component of a facility concurrently with a commissioning check of another component of the same facility, submit a separate report on each).

f. Facilities Supporting Other NAVAID(s). When a facility's primary purpose is to support a procedure on another NAVAID (e.g., NDB, V/ DME, etc.), the supporting facility must be reported on the "NAVAID(s)" report form, unless otherwise directed in the appropriate appendix.

g. Surveillance Inspection Discrepancies. To report discrepancies of services and airport conditions, use FAA Form 8240-13, Flight Inspection Report--General Characteristics. Report facility discrepancies found during a surveillance inspection on the appropriate facility report form (e.g., ILS, VOR, etc.).

h. Facility Performance. The report must reflect the facility "as left," unless specified otherwise by reporting instructions for a given facility type.

i. Satisfactory/ Unsatisfactory Report Entries. Unless otherwise stated in this order, enter "SAT" or “S” if satisfactory; enter "UNSAT" or “U” if unsatisfactory and refer to Chapter 3, Paragraph 21a.

j. AVNIS Data Change Submission. FAA Form 8240-20, AVNIS Data Change Submission, is provided within FIRPS. The completion requirements are identified in Appendix 20.

k. Precision Runway Monitor (PRM)/ Final Monitor Aid (FMA) Inspections. FAA Form 8240-5-4 is provided within FIRPS. The completion requirements are identified in FAA Order 8200.39.

l. Procedure Inspections. Report SID(s), STAR(s), and SIAP(s) on the form designated for the primary NAVAID of the procedure (e.g., an ASR approach is reported on FAA Form 8240-12, Surveillance Radar; a departure requiring interception of a radial is reported on FAA Form 8240-2, VOR, VOR/ DME, VORTAC, TACAN, VOT). Textual departure procedures not requiring the use of any NAVAID are reported on FAA Form 8240-13, General Characteristics. If procedural changes do not require recorded data, (e.g., MDA raised, controlling obstacle changed with no change in minima, or fixes within the FISSV) include the statement, “No electronic data required.”

m. Radio Frequency Interference Report. Results of Radio Frequency Interference (RFI) investigations will be included with the form designated for the type facility impacted by suspected interference.

9/28/09 8240.36M

12. Common Report Data. Any additional fields or exceptions to the following instructions are specified in the reporting instructions for each type facility. (Ident, date, and page number must be included on all pages of the flight inspection report.) Instructions for reporting common information are as follow:

a. Flight Inspection Report Header:

(1) Identifier (Ident) Field. Enter the facility IDENT listed on the itinerary or:

(a) If the procedure is to a point in space, not a designated airport, and if no ident is assigned, enter the airport identifier assigned by the National Flight Data Center (NFDC).

(b) For a stand-alone point-in-space fix, enter the ARTCC identifier without a “K” prefix (e.g., ZSE).

(c) For routes, enter route name, i.e., Q501, etc.

(d) For a Departure Procedure (DP) or Standard Terminal Arrival Route (STAR), enter the computer code listed on the itinerary.

Note: If the facility identifier is changed, refer to Chapter 3, Paragraph 21h.

(2) Owner Field. Enter the owner code listed on the itinerary.

(a) International. Facilities/ approaches/ procedures owned by the foreign government shown in the location field.

(b) Private. Facilities/ approaches/ procedures owned by nongovernmental interests. For commissioning/ reconfiguration reports only, identify the specific owner (actual corporation or organization) in the “Remarks” section.

(c) State, County, or Municipality. Facilities/ approaches/ procedures owned by a domestic governmental interest other than the Federal Government. For commissioning/ reconfiguration reports only, identify the specific owner in the “Remarks” section.

(d) Other. Facilities owned by the Federal Government other than FAA, such as U.S. Trust Territory, NASA, U.S. State Department. Indicate in the “Remarks” section the actual owning interest.

8240.36M 9/28/09

Owner Code Description A Air Force B Public C Coast Guard E FAA F&E Projects F FAA (Other than F&E( H International Public I International (Generic) J International Private K International Air Force L International Army M International Navy N Navy O Other (Specify in Remarks) P Private R Army S State X Public Special

Note: If facility ownership should change, refer to Chapter 3, Paragraph 21h.

(3) State. Enter the state code for facilities located in the United States. Click on the drop-down box and select the appropriate entry.

(4) Country. Click on the drop-down box and select the appropriate entry.

(5) Region Field. The region designator must be the authorized 3-letter code for the FAA region in which the reported facility/ approach/ procedure is located. For militaryowned facilities and foreign governments, leave blank.

(6) Date(s) of Inspection Field. Record the UTC date(s) of flight inspection as follows:

(a) Inspection started and completed in one day: 2/1/88

(b) Inspection conducted over consecutive days: 1/12-15/89

(c) Inspection conducted over several nonconsecutive days: 8/6, 8, 10/89

(d) Combined inspections: 10/16, 19-21/89.

5/30/11 8240.36M Chg 1

(7) Location Field. Facility location information will be obtained from the AVNIS Facility Data Sheet (do not enter airport name). For shipboard tactical air navigation (TACAN), enter the name of the ship and the hull number (e.g., USS Nimitz - CVN68). For point in space procedures, enter the location as identified on the PC form. For a route or a stand-alone pointin-space fix, leave blank. For DP(s), ODP(s), SID(s), or STAR(s) reported on FAA Forms 8240-13 (General Characteristics) or 8240-17 (RNAV), enter the location as specified on the AVNIS Facility Data Sheet, of the primary airport. For routes reported on FAA Form 8240-17 (RNAV), leave blank.

(8) Inspection Type. Click on the drop-down box and select the appropriate entry.

A After Accident (3) C Commissioning E Site Evaluation P Periodic R Reconfiguration S Scheduled Special(1) U Unscheduled Special V Surveillance (2) Z Radio Frequency Interference

Note 1: Shipboard TACAN(s) will always be a complete "Special" inspection.

Note 2: Surveillance inspections must be considered complete.

Note 3: Includes RADAR inspection involving a "near mid-air collision." See Order 8200.1, Chapter 14, Paragraph 14.12d.

Inspection Type Suffixes

I Incomplete Inspection: Indicates incomplete check (e.g., CI = Commissioning Incomplete, EI = Site Evaluation Incomplete). It is the second character in the dropdown for the inspection type. Explain reason for the incomplete in Remarks. Once the inspection is completed, all report requirements may be included in one report.

U Procedure Unsatisfactory: Applies to Special Procedural Inspections Only. It is the second character in the drop-down for the inspection type. It indicates when an inspection is completed, but unsatisfactory. This may be used when flight procedure inspections are unsatisfactory and need to be returned for rework.

C Procedure Satisfactory with Required Changes: Applies to Special Procedural Inspections Only. It is the second character in the drop-down box for the inspection type It indicates when an inspection is completed satisfactory, but with changes required to the procedure prior to publication and an additional flight check is not required. G Procedure Satisfactory under Gold Standard: Applies to Special Procedural Inspections only. It is the second character in the drop-down box for the inspection type. It indicates when an inspection is completed under Gold Standard.

8240.36M 5/30/11 Chg 1

b. Crew Information:

(1) Pilot-in-Command Crew Number Field. This field must contain the crew number of the pilot-in-command (PIC) of the mission (e.g., VN ###). The PIC crew number certifies the operational status of the facility and the degree to which the facility supports the approved instrument flight procedure(s) inspected. PIC entered crew number certifies the completeness and accuracy of all reported data.

When a flight inspection is accomplished over multiple dates with different flight inspectors in charge and the data obtained is combined on one report, this field must contain the crew number of the PIC during the final date of the check. Additional PIC crew numbers may be added to Remarks with corresponding flight inspection dates.

When a VOT is inspected using a portable ILS/ VOR receiver, the PIC crew number is required if there is a NOTAM issued as a result of the inspection. If a NOTAM is not issued, the PIC crew number is not required.

(2) Second-in-Command Crew Number. This field must contain the crew number of the second-in-command (SIC). When a flight inspection is accomplished over multiple dates and the data obtained is combined on one report, this field must contain the crew number of the SIC during the final date of the check.

When a VOT is inspected using a portable ILS/ VOR receiver, the SIC crew number is not required.

(3) Mission Specialist Crew Number. This field contains the crew number of the Mission Specialist and must be on all flight inspection reports unless his/ her participation is not required for the facility certification. In this case, enter "NA" in place of the crew number. The crew number of the Mission Specialist certifies the reported technical data is complete, accurate, and conforms to national standards and specifications.

(4) Aircraft Number. Enter the aircraft registration number (e.g., N99).

(5) Additional Crew Number. This field may contain the crew number of any additional crew member participating in the mission.

(6) Flight Inspection Field Office (FIFO). Enter the assigned 3-letter code of the office of the PIC conducting the inspection. If the Army accomplished the inspection, enter “Army” in the field. For other non-FAA inspections, enter “Other” and explain in Remarks.

c. Facility Information:

(1) This block contains general information about facility type, components inspected, and inspection results. These fields are dynamic and will be completed according to instructions in the appropriate appendix.

(2) Facility Status/ SIAP(s) Verified. The appropriate facility status must be entered in accordance with Order 8200.1, Chapter 5, Facility Status and Classification. SIAP(s) Verified will be used to indicate flyability of procedure(s) developed on the inspected facility. (See Chapter 3, Paragraph 21g).

d. Notices to Airmen (NOTAM(s)). This block will contain verbatim NOTAM information issued as a result of the flight inspection. (See Chapter 3, Paragraph 21d)

9/28/09 8240.36M

e. Remarks. This block will be completed according to instructions in Chapter 3 of this order (Required Reports Remarks). Additional remarks may be located in the appropriate appendix.

f. Flight Inspection Data. Information entered on the appropriate form will include all data needed to meet checklist items for the type of inspection scheduled. When a Special is completed, the Remarks block will contain enough information to convey what was requested and how the requested requirements were met, including the final result of the inspection.

13. Corrected Copies of Reports. Any report may be edited at any time by the originator before the report has been moved to Archived (A) status. If a report is in “Records Review” (RR) or Specialist Review (SR) status, the Flight Inspection Records Team must be contacted to move the report to “Rejected” status, returning the report to the originator’s pending list.

Amending an “Archived” report may be accomplished by locating the report in FIRPS using the “Select Action” menu “Amend Archived Report” option. This will generate a new Worklist Item with a special “Push Pin” icon and a “+” next to the “Pending” (P) status indicator. The first time a report is amended, “Report Amended #1”, along with the date of the amendment, will appear in the top margin of the report. The number will increase by increment of 1 for each consecutive amendment.

After Accident (AA) reports, if amended, will be annotated as described above. When an “AA” report is amended, the Flight Inspection Records Team must be notified. The “AA” report with the latest amendment date is the final report to be forwarded to investigating authority. (See Paragraph 15c(5) for more “AA” information). 14. Security Classification of Flight Inspection Reports.

a. Guidance. The military organization requiring classification of flight inspection reports must provide classification guidance either by letter or message. The guidance will be maintained on file to justify the initial classification determination (DOD 5200.1-R, Department of Defense Information Security Program Regulation).

b. Classification Markings. Flight inspection reports containing classified information must be marked in accordance with FAA Order 1600.2, National Security Information. Markings will show the degree of classification; name and routing symbol of the FAA employee applying the classification; authority for classification (reference to the military element's letter or message); safeguarding instructions and/or exemption category. If an exemption category is provided, the date the report may be declassified will be provided (if it can be determined). Specific marking instructions can be obtained from the servicing FAA security office.

c. Control of Reports. Control, handling, storage, and transmission of classified flight inspection reports must be accomplished in accordance with FAA Order 1600.2.

d. Files. FIFO(s) must not maintain classified flight inspection facility report files. The Flight Inspection Records Team must contact the Civil Aviation Security Division, AMC- 700, and obtain a security control number for all classified reports.

8240.36M 9/28/09

15. Distribution of Reports and Recordings.

a. General. Flight inspection reports must be sent to the Flight Inspection Records Team within 60 days after finishing the flight inspection. A report may include portions of an inspection (e.g., incomplete, periodic, or commissioning inspections).

All recordings will be forwarded to the Flight Inspection Records team within 15 days following assignment of “Awaiting Recording” status.

b. Recording Preparation for secure shipping to the Flight Inspection Records Team to be archived:

(1) The cover page of each recording should be annotated with the following information:

 Facility Identification and Type  Date(s) of Inspection  Type of Inspection, (e.g., C, S, P, PM, POA)  Aircraft Tail Number  Crew Member Numbers

This requirement may be satisfied by securely taping a copy (draft or final) of the first page of the flight inspection report to the outside of the recordings.

(2) Securely tape the recordings (all 4 sides), or for a large stack of recordings, an envelope may be used.

(3) A copy of the data sheet applicable to the inspection, all paperwork, and worksheets should be placed inside the folds of the recordings. When an FAA Form 8240-20 is required, a copy will be placed in the recording for archive.

(4) All packages must be shipped using boxes or fabric mailers. Padded envelopes must not be used. Shipping of recordings must be accomplished with a carrier allowing tracking of shipment.

(5) All packages must include a list of contents. As a minimum, include a list of facility ID(s), facility type, and the date of the inspection. The FIFO will retain a copy of the shipment list for their records and send a copy to the Flight Inspection Records Team via e-mail. This notification will be kept in suspense until the package arrives. The shipment notification message should be sent to the Flight Inspection Records Team at the following address: 9-AMC- AVN-Flight Inspection Reports/AMC/FAA.

Recording shipment should be made at least bi-weekly by the U.S. Postal Service or Federal Express. Ship the package to:

U.S. Postal Service Federal Express

FAA/ MMAC/ AJW-335A FAA/ MMAC/ AJW-335A

ARB, Room 117 ARB, Room 117

P.O. Box 25082 6500 S. MacArthur

Oklahoma City OK 73125 Oklahoma City OK 73169

9/28/09 8240.36M

c. Standard Distribution:

(1) FAA:

(a) Within the contiguous United States:

1 Service Area Office having jurisdiction over the facility inspected - one electronic copy.

2 Technical Operations having jurisdiction over the facilities inspected - one electronic copy.

(2) Military reports distribution for all Department of Defense (DOD) facilities will be e-mailed to the locations on file with the Flight Inspection Records Team (AJW- 335A). The Flight Inspection Records Team will work with DOD locations for changes, corrections, and deletions of account information.

(3) International. Distribute reports to address provided by customer.

(4) General Characteristics Reports.

(a) When a General Characteristics Report is generated and is not a FIRPS pending list requirement, send an electronic copy to the Flight Inspection Records Team.

(b) The Flight Inspection Records Team must send an electronic copy to the appropriate military command for local distribution, an electronic copy to the Airport Authority responsible for the service, or any other entity as deemed appropriate.

(5) After Accident (AA) Reports. After-accident reports, including FAA Form 8240-14, Flight Inspection Report – After-Accident Continuation Sheet, must be completed and forwarded to the Flight Inspection Records Team within 3 days after completion of the flight inspection. Normal report completion procedures and local QC must be accomplished in the 3day time frame. The Flight Inspection Records Team will mark the report “Specialist Review” (SR) in FIRPS, then notify Flight Inspection Policy an AA report is in SR status. Flight Inspection Policy will review and recommend changes when needed. If unsatisfactory, it will be returned to the originator for changes. The final report must be forwarded to the Flight Inspection Records Team within 7 days of completion of the inspection. The Flight Inspection Records Team must send the entire final AA Report, including FAA Form 8240-14 and the two (2) preceding periodic flight inspection reports, to the Technical Operations Service Area Flight Standards Accident Coordinator/ Investigator within 14 days of completion of the inspection. See Appendix 14 for review and completion requirements prior to the above distribution.

d. ILS/ MLS Maintenance Alert. Flight Inspection Central Operations (FICO) must send an electronic copy of the report to the Technical Operations Service Area engineer or military command. Send a copy to, to be retained with the recordings, to the Flight Inspection Records Team.

e. Private Facility or Procedure Reports. The Flight Inspection Records Team will send a copy of all private special use reports to the proponent specified in the memorandum of agreement.

8240.36M 9/28/09

f. Obstacle Evaluation Form. The Flight Inspection Records Team will send a copy to the National Flight Procedures Office.

g. Radio Frequency Interference Report. The Flight Inspection Records Team will send an electronic copy to the Spectrum Engineering Services Office.

16 - 20. Reserved

Chapter 3 - Req'd Remarks

5/30/11 8240.36M Chg 1

Chapter 3. Required Report Remarks 21. Remarks Field. Briefly note any additional information required to indicate ground-based facility performance or space-based procedural inadequacies. When “Remarks” block is not adequate for all remarks pertaining to an inspection, the continuation sheet (FAA Form 8240-1) may be added as a supplemental page to any report form. For ground-based facilities, do not go into detail about the adjustments made to obtain final results unless the inspection was made especially to ascertain the effect of the adjustments or facility configurations (e.g., engineering projects).

a. Out-of-Tolerance Conditions.

(1) Identify and, if necessary, describe each out-of-tolerance or unsatisfactory condition found. Where there is no provision to identify out-of-tolerance facility/ approach/ procedure performance (e.g., FAA Form 8240-2, Field 7), place an asterisk next to the “as left” data. Place a corresponding asterisk in Remarks and describe the condition and/ or status (corrected/ uncorrected) of the condition.

(2) For military facilities, approaches, or procedures, include a statement that military personnel or units were briefed or advised and the date (e.g., tower/ maintenance briefed 4/26/89).

b. Facility, Approach, or Procedure Narrative. When narrative references are necessary to describe the facility/ approach/ procedure, factual statements of existing conditions must be used; do not attempt to determine causal relationships based on observations. For example:

(1) Observation (Permissible).

"The facility structure has deteriorated at 210. Work was noted on a highway near the facility/ approach/ procedure in that sector."

(2) Unsubstantiated reference (Prohibited).

"The highway construction southwest of the facility/ approach/ procedure is causing deterioration of the course structure."

c. Site Evaluation, Commissioning, and Special Flight Inspection Reports. Remarks for these types of inspections must contain the special control number and/ or procedure number assigned by the FICO and sufficient detail to explain the extent of changes, modifications, and final results so they can be clearly understood by recipients of such reports. Additionally, for a maintenance request or on site request, include the reason for the inspection. This paragraph does not apply to shipboard TACAN inspections.

8240.36M 5/30/11 Chg 1

d. Notice to Airmen (NOTAM(s))/ Restrictions. Record NOTAM(s)/ Restrictions issued, revised, or cancelled as a result of the inspection. Reconfiguration flight inspections require revalidation of previous restriction(s) and, if necessary, issuance of new NOTAM(s)/ Restrictions as appropriate.

Note: During a reconfiguration flight inspection, cancel all existing restrictions and re-issue as necessary using the “Reconfiguration Date”.

Enter the NOTAM/ restriction as published (or as recommended for military facilities) and the date the NOTAM/ restriction information was forwarded to the FICO or appropriate organization. If the previous flight inspector issued the NOTAM or the facility, approach, or procedure restriction remains in effect and is not changed by the present inspection, enter, "NOTAM(s) (restriction) dated … remain in effect," in the Remarks section of NOTAM block. The Facility Status does not determine the requirement for this remark. However, once the NOTAM(s)/ restriction(s) information is included in the DOD Flight Information Publication, United States Government Flight Information Publication, or other appropriate publication, this remark is not required. The current NOTAM information as issued will be maintained in the AVNIS facility data.

e. Facility Status. If a facility/approach/procedure classification status is changed as a result of the flight inspection, enter appropriate remarks to identify the reason for the change along with a verbatim copy of the published NOTAM (see Paragraph 21d). Include who was notified and when.

f. Lighting Systems that Support Lower Approach Minima. Lighting systems that support lower approach minima include Approach Lights (APL), High Intensity Runway Lights (HIRL), Touchdown Zone Lights (TDZL), and Runway Centerline Lights (RCL). When the report form contains a “lighting systems” block, enter the appropriate results (SAT/ UNSAT). In the case where there is no “lighting systems” block, OR when there is a discrepancy, enter a remark identifying the lighting system, the results, and the details of the discrepancy, if any: (e.g., ALSF-1, touchdown zone and centerline lighting, Rwy 11 checked satisfactory; MASLR Rwy 27 checked unsatisfactory, threshold light bar and RAIL inoperative). When conducting a commissioning/ reconfiguration inspection of lighting that supports lower approach minima, either in conjunction with a NAVAID approach or as a separate system, include a list of the relevant instrument approach procedures (SIAP(s)). Note that Commissioning, Reconfiguration, or Special inspections specifically for lighting systems will be reported on FAA Form 8240-5 (see Appendix 5, the beginning section and Paragraphs 3f and 5b).

g. Standard Instrument Approach Procedures (SIAP(s)). A periodic SIAP inspection includes all the standard requirements as listed in Chapter 6 of FAA Order 8200.1, except at Operational Network (OPSNET) airports. The obstacle verification will be scheduled by runway end. If procedural changes do not require recorded data, (Example: MDA raised, controlling obstacle changed with no change in minima, or fixes within the FISSV) include the statement, “No electronic data required.”

Note: If required, report the SIAP information in the following order: Airport name, city, state, SIAP(s), and amendment number (e.g., Tulsa Int’l, Tulsa OK, VOR Rwy 23, Amdt 1).

5/30/11 8240.36M Chg 1

If one of the following circumstance(s) is applicable to the inspection of a SIAP(s), report the results of the inspection appropriately:

(1) Periodic Evaluation. Enter the following in Block 5, Remarks: "SIAP/ SIAP(s) verified IAW Order 8200.1, Chapter 6” or use dedicated SIAP field when provided, entering “SAT” or “UNSAT”.

Note: SIAP(s) at OPSNET airports do not require an obstacle evaluation to complete a periodic inspection. Obstacle evaluation will be by scheduled inspection(s).

(2) New or amended SIAP(s). Report the SIAP information with the statement "SIAP verified IAW Order 8200.1, Chapter 6."

(3) SIAP not checked. During an evaluation when all SIAP(s) are required and all are NOT checked, select SAT/ Incomplete*”. In Remarks, record the incomplete SIAP name with the statement, "SIAP not inspected."

(4) SIAP found unsatisfactory. During an evaluation when all SIAP(s) are required, a SIAP is found satisfactory and another SIAP is found unsatisfactory, select “SAT/ UNSAT*”. In Remarks, record the name of the unsatisfactory SIAP(s) and describe the condition in detail.

(5) More than one SIAP is identified on a single page of the DOD Flight Information Publication or United States Government Flight Information Publication. SIAP verification, when accomplished, must be entered on the appropriate form (i.e., If the SIAP is a compound type, such as an ILS/ TACAN RWY 17, report the ILS part on an ILS form and the TACAN part on a TACAN form).

(6) After Accident Reports. If the information is contained on the after accident continuation sheet, an entry in this field is not required.

h. AVNIS Facility Data. If the facility Location, Identifier, Owner, and/or Equipment is changed, report the revised data on the first facility inspection report following the change. The Remarks block will have the old and the new facility information.

i. Expanded Service Volume (ESV). Include appropriate remarks regarding the status of the ESV check (i.e., if unsatisfactory, explain why). When establishing a fix, state whether the fix displacement area is SAT/ UNSAT. Indicate if the ESV check is an original request or a revalidation.

VOR/ TACAN/ NDB: Whenever the ESV is established or revalidated, define the lower limits by facility component, azimuth (radial From) or beginning and ending azimuth on an arc distance and minimum reception altitude (MRA). (Example: VOR/ R-090/ 45.0 nm/ 16,000 ft Revalidation, SAT). Each component will have its own ESV entry. When DME is included in the ESV, it will be listed separately, “DME/ R-090/ 45.0 nm/ 16,000 ft Revalidation, SAT”. There is no requirement to document on a report the requested upper limit of the ESV; however, if the upper limit is flown or specifically requested to be checked on FAA Form 6050-4, the altitude must be reported.

8240.36M 5/30/11 Chg 1

ILS: Both upper and lower limits are required for localizers and TLS. Azimuth is not required on ILS. (Example: ILS/ L/ 6,000’ – 2,000’/ 28.0 nm ORIG SAT).

j. 75 MHz Marker Beacons that Support an Instrument Approach Procedure. The operation of 75 MHz markers must be documented on the report that certifies the primary NAVAID, (e.g., VOR, ILS, NDB).

(1) Commissioning, change of transmitters or antennas: enter all checklist items checked and their status (Example: "Satisfactory" or "Unsatisfactory"). If dual equipment is installed, document the minor axis width for both transmitters.

(2) Periodic type inspections. For non-ILS, enter a statement to indicate the marker was checked satisfactorily (Example: 75 MHz marker system(s) checked "satisfactory" or "unsatisfactory").

k. Weather Broadcast Information. On commissioning reports only, list all weather broadcast capabilities for each facility inspected.

l. Other. Enter all other remarks required by the appendixes in this order.

m. Special Checks Which Meet Periodic Requirements. When a special check meets periodic requirements, enter the remark, “Periodic requirements met.” (Updating the periodic inspection following an after-accident inspection has to meet specific conditions—see Appendix 14, Paragraph 2c). If necessary, identify which transmitter was completed (Example: xmtr #1—periodic requirements met; xmtr #2—out of service).

n. Critical Area Interference Checks. When a Critical Area Interference Check is accomplished, enter the following, “The FAA does not consider this flight inspection as a valid check of interference caused by aircraft/vehicles in the ILS critical zone.”

o. Structure Tolerance (95% Rule). Notify the FICO when the structure tolerance 95% rule is applied to a Category II/ III facility. The FICO must notify the applicable service area or military command engineering staff upon initial application of these criteria. Enter in Remarks “FICO notified 95% rule applied”. (Ref Order 8200.1, Paragraph 15.21.)

p. Rho-Theta Magnetic Variation Change Inspection. Include remarks detailing the published facility restriction, receiver checkpoint, and ESV radial changes based on the MAGVAR change. For example, a published coverage restriction of 210 - 250 would be changed to 214 - 254 after a MAGVAR change from 2 West to 6 West. Submit the appropriate changes to the Aeronautical Data Support Team on FAA Form 8240-20.

q. Completion of an Inspection Previously Reported as Incomplete. Enter a statement indicating the check completes the inspection requirements of the report dated mm/dd/yy (Example: This completes the requirements for the inspection dated 02/11/02).

r. RFI Checks. Enter a narrative description of checks performed and results obtained. Provide physical description and latitude/ longitude of suspected interference source. For incomplete or unsuccessful checks, report bearings obtained, and aircraft location; provide any information that may aid another crew in locating the source.

5/30/11 8240.36M Chg 1

19 (and 20)

s. 1800 RVR. For CAT I ILS facilities that fail to support a SIAP that allows 1800 RVR authorization with the use of Flight Director (FD) or Autopilot (AP) or Heads-up Display (HUD) to Decision Altitude (DA), include a statement in Remarks, “System does not meet the 1800 RVR requirements. NOTAM issued through FICO, and Flight Inspection Policy notified (date)”.

22 - 25. Reserved.

This Page Intentionally Left Blank

Appendix 1 - FI Forms

5/30/11 8240.36M Chg 1 Appendix 1

Appendix 1. Flight Inspection Forms The FAA flight inspection report forms contained in this order are intended to be computer generated. If this process is not available, local reproduction of the forms included in each appendix is authorized. Handwritten reports must be uploaded to FIRPS by creating a worklist item for archiving purposes.

FAA Form Date Title

8240-1 7/2005 Flight Inspection Report – Continuation Sheet

Note: Use this continuation sheet when additional space is required to document facility performance. Use the same heading information as in the primary report.

8240-2 10/2005 Flight Inspection Report – VOR, VOR/DME, VORTAC, TACAN, VOT

8240-2 10/2005 Flight Inspection Report – VOR, VOR/DME, VORTAC, TACAN, VOT – Radial Data

8240-2 7/2005 Flight Inspection Report - VOR, VOR/DME, VORTAC, TACAN ORBITAL Data

8240-4 8/2010 Flight Inspection Report – Ground-Based Augmentation System (GBAS)

8240-5 7/2005 Flight Inspection Report – Non-Directional Beacon, Direction Finding, Visual Aids, Communications

8240-6 7/2005 Flight Inspection Report – Precision Approach Radar

8240-6 7/2005 Flight Inspection Report – Precision Approach Radar GPN-22 / TPN-25 Continuation Sheet

8240-6 7/2005 Flight Inspection Report – Precision Approach Radar TPN-22 Continuation Sheet

8240-7 7/2005 Flight Inspection Report - ILS Worksheet

8240-7-1 7/2005 Flight Inspection Report - ILS Continuation Worksheet

8240-8 7/2005 Flight Inspection Report – Instrument Landing System

8240-8 7/2005 Flight Inspection Report – Instrument Landing System Azimuth Part I

8240-8 7/2005 Flight Inspection Report – Instrument Landing System Azimuth Part II

8240-8 7/2005 Flight Inspection Report - Endfire Glide Slope Transverse Structure Plot

8240.36M 9/28/09 Appendix 1

FAA Form Date Title

8240-11 7/2005 Flight Inspection Report – ILS/ MLS Maintenance Alert

8240-12 12/2005 Flight Inspection Report – Surveillance Radar

8240-13 10/2005 Flight Inspection Report – General Characteristics

8240-14 7/2005 Flight Inspection Report – After-Accident Continuation Sheet

8240-16 7/2005 Flight Inspection Report – Microwave Landing System

8240-16 7/2005 Flight Inspection Report – MLS Commissioning Data Words

8240-17 12/2005 Flight Inspection Report - RNAV

8240-20 12/2005 AVNIS Data Change Submission

8240-21 10/2005 Flight Inspection Report – Controlling Obstacle Evaluation

9/28/09 8240.36M Appendix 1

A1-3 (and 4)

Flight Inspection Report—Continuation Sheet

FAA Form 8240-1

This Page Intentionally Left Blank

Appendix 2 - VOR Rpt

5/30/11 8240.36M Chg 1 Appendix 2

Appendix 2. Flight Inspection Report--VOR, VOR/ DME, VORTAC, TACAN, VOT

FAA Form 8240-2 FAA Form 8240-2 will be used to report recorded inspection data collected during all flight inspections. When an applicable facility is the primary guidance for a procedure, this form will be used to track procedure amendments. 1. Block 1 - Flight Inspection Report Header. Complete IAW Chapter 2, Paragraph 12.

2. Block 2 - Aircrew Information. Complete as shown in IAW Chapter 2, Paragraph 12.

3. Block 3 - Facility Information.

a. VOR, TACAN, DME Coverage, DME Accuracy, and VOT Fields. Click the appropriate drop-down box to identify all components of the facility being reported. When a VOT is inspected using a PIR, choose “Inspected/ PIR” from the drop-down box. For DME, also indicate the status of the inspection (i.e.”SAT” or “UNSAT”).

b. Voice, Standby Power, and Ident. When any of these items are inspected, click on the drop-down box and select the appropriate entry. Select the type of voice transmission from the drop-down menu and operation status.

c. Type Facility. Use the drop-down menu and select the appropriate entry to indicate the type facility.

d. Facility Status. Use the drop-down menu and select the appropriate entry. Status is determined according to Order 8200.1, Chapter 5.

e. SIAP(s) Verified. Complete IAW Chapter 3, Paragraph 21. Click the dropdown menu and select the appropriate entry.

4. Block 4 - NOTAM(s). Complete as shown in Chapter 3, Paragraph 21.

5. Block 5 - Remarks. Complete IAW Chapter 3. Additionally, after commissioning or reestablishing a receiver checkpoint, describe it in this field. Include the airport name and state (if on an airport), altitude at which check is made (airborne checkpoints), azimuth in degrees magnetic, the distance in miles and the checkpoint description (e.g., Ground Checkpoint: University of IL- Willard, IL, 332, 0.9nm, on runup pad Rwy 14; Airborne Checkpoint: 2,000’, 175, 8.0 nm, over grain elevator at Pesotum; VOT reference point: Approach end of Runway 35R). Notify the Aeronautical Information Specialist, via FAA Form 8240-20 (fill out form IAW Appendix 20) of the establishment or cancellation of receiver Checkpoints.

a. Radial Alignment. Report when radial alignment is authorized by Flight Inspection Policy in lieu of an alignment orbit.

b. VOT. When commissioning a VOT, indicate the identification feature (dots or a series of dots that cannot be interpreted as Morse code).

8240.36M Chg 1 5/30/11 Appendix 2

c. USAF VOR(s). For USAF VOR(s), enter the modulation values found on at least one radial or arc segment flown during the inspection. These values must be reported in the following format: modulations/ radial flown or arc/ start - stop radials/ distance(s) to the nearest mile/ MSL altitude divided by 100. Radial example: AM=30.8, FM=16.4, 9960=29.5/312/16- 12/37. Orbital example: AM=30.9, FM=15.8, 9960=32.1/312 cw 349/40/25.

d. Reference Alignment. Indicate the date Maintenance was notified of ARR/ orbit reference alignment establishment/ re-establishment, IAW Order 8200.1, Chapter 11.

e. Transmitter Changes When Conducting an Alignment Orbit. Include the following remark, “Transmitter changes were accomplished during the alignment orbit IAW Order 8200.1, Paragraph 11.20f(1)(c), beginning with transmitter ___.”

f. VOT Inspected Using a Portable ILS/ VOR Receiver.

(1) Record the PIR detected course deviation, modulation levels, and signal strength.

(2) Record the model, serial number, and calibration date of the PIR.

(3) Add the following statement, “Aviation System Standards Flight Inspection Policy Team authorized VOT flight inspection via PIR.”

(4) Do not add any data in Field 7C (Radial Data) of FAA Form 8240-2.

(5) Place an asterisk in the “Aircraft Number” field.

6. Block 6 - Flight Inspection Data. For a periodic with orbit inspection, report the orbital data in 6A. Do not enter a date in the “Ref Date” field for periodic data. Completion of both 6A and 6B is required when the reference radial and mean orbital alignment are established/ reestablished. This block should also be completed when there is a need to permanently change flight profiles (e.g., direction, distance and /or altitude). The Data Specialist will transfer data from the flight inspection report to the AVNIS data sheet whenever there is a date entered in the “Date Established” field.

Enter the azimuth monitor evaluation results when accomplished.

When out of tolerance condition(s) are found during an orbit, Block 8, Orbital Data, must be reported.

a. Orbital Data. Enter the mean alignment (e.g., + 0.2). Enter the maximum negative and the maximum positive alignment error (include the sign). FIRPS will automatically calculate and enter the “spread”.

Enter the orbit direction (CW or CCW) under the DIR field.

Enter the altitude divided by 100 in this block when the altitude is the same during the entire orbit. If altitude changes were required during the orbit, annotate in Block 5 - Remarks indicating the different altitude(s) divided by 100 and the radial where the altitude change occurred (e.g., Altitude changed on alignment orbit 50/ 015-090, 60/ 091-135, etc.).

5/30/11 8240.36M Chg 1 Appendix 2

Enter the distance the alignment orbit was flown to the nearest tenth of a mile. If the distance changed during the alignment orbit, annotate in Block 5-Remarks indicating the distance changes and the radials where the distance change occurred (e.g. Distance changed on alignment orbit 9/ 015-090, 8/ 091-135, etc).

b. Reference Radial/ Monitor. Select “VOR” or “VOT”. This field requires no ARR data unless a new reference is accomplished or a monitor check is conducted. The ARR data will normally be in the Block 7 Radial Data block of the report.

(1) Reference Radial. For AFIS, enter the azimuth, the segment distance (to the nearest mile), and the altitude flown divided by 100 (Example: 270/ 20-15/ 45). When a Checkpoint is used, enter the azimuth and distance of the reference Checkpoint and the altitude flown divided by 100 (Example: 265.5/ 18.3/ 45).

For VOT, enter the azimuth 360/ from (Example: 360/ from).

(2) Checkpoint. For VOR monitors evaluated airborne, enter the location as detailed above for the Reference Radial. If monitors are checked where the Reference Radial/ Checkpoint was evaluated, enter "Same." If the monitors are established on the ground, enter the azimuth, distance, and the term "Gnd" (Example: 041.1/6.7/Gnd). Describe the airport location in the Remarks field (carrying forward the airport location on subsequent reports is optional).

For VOT monitors, enter "VRP" if VOT Reference Point is used for monitor evaluation. If the “VRP” is not used, enter an * and describe, in Remarks, the Checkpoint location where the evaluation was accomplished.

(3) TX, Alignment, Alarm +, Alarm -. Use the appropriate fields to report the results of the Reference Radial/ monitors.

(a) “TX”. Enter the transmitter evaluated. If a facility has two tranmitters and both are checked, enter the transmitter number as in the example for Dual Transmitters.

(b) Enter the “normal condition” alignment error determined at the Reference Radial/ Checkpoint, or ARR if AFIS is used, in the Reference Radial “Alignment” column.

(c) When monitors are checked, enter the amount of shift. “Alarm +” is clockwise, AFIS code "R" and “Alarm -“ is counterclockwise, (AFIS code L) in the Checkpoint columns. The amount of shift must be referenced to the “normal condition” alignment error measured at the location the monitors are checked. The Checkpoint “Alignment” column will be left blank. See Examples 1 and 2.

8240.36M Chg 1 5/30/11 Appendix 2

Example 1. Single Transmitter

TX ALIGNMENT ALARM + ALARM -

Reference Radial 265.5/ 18.3/ 45 1 -0.4

Checkpoint Same 1 0.9 0.9

Example 2. Dual Transmitter

TX ALIGNMENT ALARM + ALARM -

Reference Radial 270/ 20-15/ 45 1/ 2 -0.4/ -0.5

Checkpoint 042.0/ 6.7 nm/ GND 1/ 2 0.9/ 0.8 0.8/ 0.7

c. Date Established. Enter the month, day, and year that the orbit/ reference radial alignment was established/ re-established for each facility/ component checked.

9/28/09 8240.36M Appendix 2

7. Block 7 - Radial Data

a. Service Designation. Use the drop-down menu and select the appropriate facility.

b. Radial Use. Use the drop-down menu (see table below) for radial use selection. “ESV” or other abbreviations may be used if explained in the “Remarks” portion of the report. This field may be left blank.

Standard examples are as follow:

ARR Automated Flight Inspection System (AFIS) Reference Radial

Ref Reference Radial

V16 Airway

GCP Ground Receiver Checkpoint

ACP Airborne Receiver Checkpoint

Apch Approach

IApch Initial Approach

MApch Missed Approach

Hold Holding Pattern

J180 Jet Route

Dir Direct Route

RNAV Area Navigation (RNAV) Procedures

Null Null Radial

5DEG Offset (Special Check) of VOR APCH

FEDR Feeder

INTX Radial Used to Support a Fix or Intersection

STAR Standard Terminal Arrival Route

SID Standard Instrument Departure

COV Coverage Radial

DP Departure Procedure

c. Azimuth. Enter the magnetic azimuth from the facility (in whole degrees). For RNAV procedures, enter the procedure start/ stop azimuth in tenths of degrees (Example: 120.6 - 060.5). VOT azimuth is entered as "360/ from."

d. Transmitter (s). Identify the transmitter checked. If transmitters were alternated during one check, enter the transmitter with the greatest alignment error first, (Example: 2/ 1 with TX 2 having the greatest error).

8240.36M 9/28/09 Appendix 2

e. MSL Altitude. Enter the altitude divided by 100 (e.g., "20" for 2,000 feet, "7.2" for 720 feet). If altitude changes occurred, enter the highest and lowest altitudes in the order checked (e.g., 20/ 7.2). Leave blank when reporting ground Checkpoints.

f. Distance From/ To. Show the starting point (From) and the termination point (To) in nautical miles from the facility.

g. Roughness/ Scalloping. For in tolerance parameters, enter the maximum amplitude to the nearest tenth of a degree and indicate the distance from the station (Example: 2.2/ 16.0).

For Out-of-tolerance (OT) parameters, enter the amplitude and distance closest to the facility. When reporting OT roughness/ scalloping that meets acceptable aggregate criteria, report the worst case of roughness/ scalloping, the mileage where it occurred, and place an asterisk in the reporting field, e.g., *5.0/ 25.5. In the Remarks block, place a corresponding asterisk and state "Order 8200.1, Paragraph 11.60a (VOR) or 11.60b (TACAN) applied." If OT occurs multiple times on one radial in separate segments, enter each additional segment in the Remarks block.

For RNAV procedures, report maximum roughness/ scalloping and azimuth (Example: 1.5/ 010).

h. Bends/ CMA and Bends. For in tolerance parameters, enter the maximum Bend and Bend/ CMA amplitude to nearest tenth of a degree. Indicate the direction of the bend as “+” or “-“ value, and the distance from the facility where it occurs (Example: + 1.2/ 15.6).

For Out-of-tolerance (OT) paramenters, enter the OT amplitutde and distance closest to the facility. (See above subparagraph when entering multiple OT conditions.)

i. Polarization. Enter an “S” if Satisfactory or “U” if Unsatisfactory. Explain Unsatisfactory conditions in Remarks.

j. Alignment Error. Enter the alignment error, as a "+" or "-" value, and the distance from the facility at which it occurs.

If AFIS average alignment is reported, indicate the alignment and the start-stop distance from the facility thoughout the entire area that was sampled (Example: + 0.5/ 10.2-65.5).

Visual references used in evaluating radial alignment to runway thresholds or airport environments will be reported as “SAT” (Satisfactory) or “UNSAT” (Unsatisfactory).

When an RNAV procedure is evaluated using AFIS orbital techniques, enter the average orbit alignment error and start-stop radials of measured arc.

k. Modulations. Enter "SAT" for satisfactory or "UNSAT" for unsatisfactory. For USAF VOR facilities, enter all modulation values in “Remarks”.

l. Transmitter Difference. Enter the difference of course alignment between transmitters, to the nearest tenth of a degree.

9/28/09 8240.36M Appendix 2

m. Signal Strength. For VOR signal strength in microvolts, enter the actual value. For OT levels, enter value with asterix (Example: “4*”). In Remarks, enter the distance OT occurred. Signal strength exceeding 300 V may be reported as 300+.

Report TACAN signal strength as Satisfactory “SAT”. For Unsatisfactory TACAN signal strength, enter “UNSAT*” and the distance nearest the facility it occurred (Example: UNSAT*/ 25). Enter Remarks “*Maintenance Briefed and date of briefing”.

n. Interference. Enter "SAT" if no interference is observed; enter "UNSAT*" if interference occurs and document the area of interference in the Remarks Block.

8. Block 8 - Orbital Data

a. Block 8A, Transmitter Number (No). Select the appropriate transmitter for VOR and the appropriate transponder for TACAN.

b. Block 8B, DME Distance Unlock. Select the check box when there are unlocks and list the azimuth at which they occur (Example: 012-023, 350-001) in Block 8B.

c. Block 8C, TACAN Azimuth Unlock. Select the check box when there are unlocks and list the azimuth from the facility for the area where unlocks occur (Example: 012-023, 350- 001).

d. Block 8D, Area of interference. Select the check box when there is an area of interference observed to have a detrimental effect on the usability of the facility. List the azimuth from the facility for the area the interference is observed (Example: 012-023, 350-001).

e. Block 8E, VOR Azimuth exceeds 2.5. When radial displacement exceeds  2.5, enter the maximum course displacement and azimuth of occurrence in the appropriate block. Each block represents a 10 segment of the orbit. In the “00” block, an entry of azimuth misalignment from 000 - 009 may be recorded (Example: 2.6/ 006) and in the “10”block, azimuth misalignment from 010 - 019 may be recorded (Example: 2.8/ 017).

f. Block 8F, TACAN Azimuth exceeds 2.5. When a radial displacement exceeds ±2.5º, enter the maximum course displacement and azimuth of occurrence in the appropriate field. Each field represents a 10 segment of the orbit. In the “00” field, an entry of azimuth misalignment from 000 - 009 may be recorded (Example: 2.6/ 006) and in the “10” field, azimuth misalignment from 010 - 019º may be recorded (Example: 2.8/ 017).

g. Block 8G, VOR Coverage – Signal Strength. (Document levels below -93 dbm or 5 V.) If the VOR signal strength drops below -93 dbm or 5 V, enter the lowest value in the appropriate field. Each field represents a 10º segment of the orbit. In the “00” field, SS below 5 µV between radials 000 – 009 may be recorded (Example: 3/ 006) and in the “10” field, SS below 5 V between radials 010 - 019º may be recorded (Example: 4/ 017).

h. Block 8H, TACAN Coverage-Signal Strength (at which Azimuth or Distance Unlock Occurs). When TACAN or DME (U.S. Navy shipboard TACAN) signal strength drops to a level which causes Azimuth or DME unlock, enter in the appropriate field following the example in Paragraph 8g above.

8240.36M 9/28/09 Appendix 2

Flight Inspection Report--VOR, VOR/ DME, VORTAC, TACAN, VOT

FAA Form 8240-2

9/28/09 8240.36M Appendix 2

7. VOR, VOR/DME, VORTAC, TACAN, VOT - RADIAL DATA

Service Designation Radial Use Azimuth Transmitter(s) MSL Altitude Distance From Distance To Roughness/Scalloping Bend/CMA Bends Polarization Aligrinent Error Modulations Transmitter Diff. Signal Strength Interference

Service Designation Radial Use Azimuth Transmitter(s) MSL Altitude Distance From Distance To Roughness/Scalloping Bend/CMA Bends Polarization Alignment Error Modulations Transmitter Diff. Signal Strength Interference

Service Designation Radial Use Azimuth Transmitter(s) MSL Altitude Distance From Distance To Roughness/Scalloping Bend/CMA Bends Polarization Alignment Error Modulations Transmitter Diff. Signal Strength Interference

* Remarks are required for fields marked with an asterisk FAA Form 8240-2 (v1.0 10-2005) Supersedes previous edition PAGE 2 OF 2

8240.36M 9/28/09 Appendix 2

8. VOR. VOR/DME. VORTA VOT - ORBITAL DATA A. TRANSMITTER NO TRANSMITTER 1 TRANSPONDER 1 TRANSMITTER 2 TRANSPONDER 2 B. DME DISTANCE UNLOCK

C. TACAN AZIMUTH UNLOCK

D. AREA OF INTERFERENCE

E. VOR AZIMUTH EXCEEDS 2.5 DEGREES

F. TAC AZIMUTH EXCEEDS 2.5 DEGREES

G. VOR COVERAGE SIGNAL STRENGTH (DOCUMENT LEVELS BELOW -93dbm OR 5 uV)

H. TACAN COVERAGE - SIGNAL STRENGTH (AT WHICH AZIMUTH OR DISTANCE UNLOCK OCCURS)

*Remarks are required for fields marked with an asterisk FAA Form 8240-2 (v1.0 7-2005) Formerly 8240-4

5/30/11 8240.36M Chg 1

Appendix 3

Appendix 3 - Reserved

(Reserved)

This Page Intentionally Left Blank

5/30/11 8240.36M Chg 1 Appendix 4

Appendix 4. Flight Inspection Report—Ground-Based Augmentation System

(GBAS) FAA Form 8240-4 FAA Form 8240-4 must be used for reporting GBAS commissioning, periodic, and special inspections. A separate form will be required for each GBAS located at the airport. Multiple GBAS facilities may be installed depending upon site requirements. 1. Block 1 - Flight Inspection Report Header. Complete IAW Chapter 2, Paragraph 12. 2. Block 2 - Crew Information. Complete IAW Chapter 2, Paragraph 12. 3. Block 3 - GBAS Coverage

Appendix 4 - GBAS

a. Profile. Select drop-down box and enter direction of flight, “CW” for clockwise or “CCW for counter clockwise.

b. Altitude. Enter minimum altitude flown, divided by 100 (e.g. “20” for, 2,000 feet, “7.2” for 720 feet.). If altitude changes occurred, enter the highest and lowest altitudes in the order checked (e.g., 20/ 7.2).

c. Radius. For orbital assessments enter distance in “nm” nautical miles from the reference point on the field. Reference point will be the LAT/ LONG coordinates of the GBAS.

d. Signal Strength. Enter the minimum field strength in dB(s).

e. Dmax nm. For facilities broadcasting Dmax, enter the Maximum Use Distance as defined by the GBAS Facility (e.g., 22.7). If positive course guidance and data continuity cannot be maintained to the Dmax distance, the facility must be restricted.

f. GBAS Frequency. Enter the GBAS Frequency.

g. Polarization. Select the drop-down box and enter the type of polarization associated with the GBAS.

h. SIAP(s) Verified. Select the drop-down box and complete IAW Chapter 3, Paragraph 21g.

i. Facility Status. Use the drop-down menu and select the appropriate entry. Status is determined according to Order 8200.1, Chapter 5. 4. Block 4 - NOTAM(s). Complete IAW Chapter 3, Paragraph 21. 5. Block 5 - Remarks. Complete IAW Chapter 3, Paragraph 21. For commissioning type inspections, if the facility is not FAA owned, identify the owner.

8240.36M Chg 1 5/30/11 Appendix 4

6. Block 6a – VHF Data Broadcast (VDB) Coverage Assessment. Enter the VDB Coverage information.

a. Runway ID. For an approach, enter the runway served by the procedure.

b. Airport ID. Enter the airport identification listed in the SIAP information for each approach procedure.

c. Lower Limit. Select drop-down box and enter an “S” if Satisfactory or “U” if Unsatisfactory. Explain Unsatisfactory conditions in Remarks.

d. Upper Limit. Select drop-down box and enter an “S” if Satisfactory or “U” if Unsatisfactory. Explain Unsatisfactory conditions in Remarks.

e. Left Limit. Select drop-down box and enter an “S” if Satisfactory or “U” if Unsatisfactory. Explain Unsatisfactory conditions in Remarks.

f. Right Limit. Select drop-down box and enter an “S” if Satisfactory or “U” if Unsatisfactory. Explain Unsatisfactory conditions in Remarks.

g. Missed Approach. Select drop-down box and enter an “S” if Satisfactory or “U” if Unsatisfactory. Explain Unsatisfactory conditions in Remarks.

h. Rollout. Select drop-down box and enter an “S” if Satisfactory or “U” if Unsatisfactory. Explain Unsatisfactory conditions in Remarks.

i. CVG MVA (Coverage from Minimum Vector Altitude). Select drop-down box and enter an “S” if Satisfactory or “U” if Unsatisfactory. Explain Unsatisfactory conditions in Remarks.

j. CVG USV (Coverage from Upper Service Volume). Select drop-down box and enter an “S” if Satisfactory or “U” if Unsatisfactory. Explain Unsatisfactory conditions in Remarks. 7. Block 6b – Final Approach Segment (FAS) Data. Enter the FAS Data information

a. Runway. For an approach, enter the runway served by the procedure.

b. Airport ID. Enter the airport identification listed in the SIAP information for each approach procedure.

c. CRC Code. Enter the exact CRC remainder as indicated on FAA Form 8260-10 or equivalent.

d. Channel Number. Enter the assigned Channel number for each SIAP.

e. Reference Path Identifier (RPI). Enter the broadcast Morse code RPI for each SIAP (e.g., G22B).

f. Course Alignment. Enter the actual course error (e.g., L00.01).

5/30/11 8240.36M Chg 1 Appendix 4

g. Glide Path Angle. Enter the proposed commissioned vertical path angle and the actual vertical path angle for the GBAS final approach segment (e.g., 3.00/ 3.02).

h. TCH. Enter the procedurally calculated TCH and the actual derived TCH for the GBAS final approach segment in feet (e.g., 55/ 51). 8. Additional Pages. Use FAA Form 8240-4-3 to add additional VDB coverage assessment and FAS data information. Use FAA Form 8240-4-4 if additional remark information is needed.

8240.36M Chg 1 5/30/11 Appendix 4

Flight Inspection Report—Ground-Based Augmentation System (GBAS)

FAA Form 8240-4 (Page 1 of 4)

5/30/11 8240.36M Chg 1 Appendix 4

light Inspection Report—Ground-Based Augmentation System (GBAS)

FAA Form 8240-4 (Page 2 of 4)

8240.36M Chg 1 5/30/11 Appendix 4

Flight Inspection Report—Ground-Based Augmentation System (GBAS)

FAA Form 8240-4 (Page 3 of 4)

5/30/11 8240.36M Chg 1 Appendix 4

A4-7 (and 8)

Flight Inspection Report—Ground-Based Augmentation System (GBAS)

FAA Form 8240-4 (Page 4 of 4)

This Page Intentionally Left Blank

Appendix 5 - NDB, Comm, DF

5/30/11 8240.36M Chg 1 Appendix 5

Appendix 5. Flight Inspection Report— Nondirectional Beacon,

Direction Finding, Visual Aids, Communications

FAA Form 8240-5 FAA Form 8240-5 will be used to report all commissioning, periodic, special inspections, and after accidents of the aids listed on the form. All bearings will be reported as “FROM” the facility unless there is a specific need to report them as “TO” the facility.

Non-directional beacon (NDB) as a Compass Locator will be reported on FAA Form 8240-8 as part of the ILS inspection or when an associated NDB inspection impacts the ILS procedure. Two (2) reports will be required when NDB and ILS are separate inspections on an itinerary. (Example: An NDB has an approach and supports an ILS: one report is required when the periodic is conducted on the NDB approach only.)

When a discrepancy is found for any lighting system (except VGSI type) in the course of conducting an inspection of a SIAP or NAVAID, it will be reported on the form associated with that SIAP or NAVAID. Note that the “Lighting System” block (on some forms) is intended only for those lights that support lower minima on an approach (SIAP) (e.g., Touchdown Zone (TDZ), Runway Centerline Lights (RCL), High Intensity Runway Light (HIRL) supporting Category I approach minima). All inspections of VGSI systems, (e.g., PAPI and VASI) requiring a report will be reported on this form. All Special, Commissioning, or Reconfiguration inspections of any lighting system will be reported on this form. 1. Block 1 – Flight Inspection Report Header. Complete IAW Chapter 2, Paragraph 12. Exceptions:

a. Identifier (Ident)

(1) Instrument Flight Rules (IFR), airport night evaluations, and general airport lighting (i.e., taxiway lighting): use AVNIS airport identifier.

(3) CONUS visual aids: enter the AVNIS runway identifier. Runway lighting systems (HIRL(s), (MIRL(s), centerline lights, etc.) may require two reports, one report for each end of the same runway (Example: KSNA 19R and KSNA 01L).

(4) International visual aids, including runway lighting systems: enter the AVNIS runway identifier.

(5) Charted Visual Flight Procedures (CVFP(s)): enter the AVNIS airport identifier. Multiple procedures to the same airport may be reported on one report form.

(6) Communications: enter the AVNIS identifier for the facility being checked (Example: KSLC, ZLA).”

b. Location. Complete IAW Chapter 2, Paragraph 12, and include the NDB name in parenthesis if different than the NDB location name. For charted visual flight procedures (CVFP(s)), enter the location listed in the SIAP information.

8240.36M Chg 1 5/30/11 Appendix 5

2. Block 2 - Crew Information – Complete IAW Chapter 2, Paragraph 12. 3. Block 3 - Facility Information. Indicate facility/ component inspected status or as left condition, as appropriate. Use the drop-down menu to select the appropriate entry for the following:

a. Direction Finding

b. Communications

c. Visual aids

d. NDB

e. NDB/ DME

f. Facility Status. Complete IAW Chapter 2, Paragraph 12c. For Communications inspections, leave blank. For all lights (except VGSI systems) it is not intended that discrepancies found during flight inspection will result in restrictions to use of lighting unless a hazard to safety exists. Should it be determined that a significant hazard does exist, the lights status should be classified as “unusable.” When reporting on an inspection to restore a lighting facility previously classified as “unusable,” report its status as “unrestricted” if successful. VGSI systems, (e.g., PAPI and VASI) should always be assigned a status IAW Chapter 2.

g. SIAP(s) Verified 4. Block 4 - NOTAM(s). Complete IAW Chapter 3, Paragraph 21d. If the NDB is associated with an ILS, the restrictions must be added to the ILS AVNIS data sheet. 5. Block 5 - Remarks. Complete IAW Chapter 3.

a. NDB(s). When routes are flown, enter the route name (if assigned), bearing, altitude, and distance flown (Example: B9 030/ 2800/ 45.0). When the NDB is also used as a compass locator associated with an ILS system, enter the ILS identification on commissioning reports only (e.g., compass locator/ LOM/ LMM associated with RGR ILS).

b. Visual Aids. Indicate if the inspection is a night evaluation. Describe the type of lighting system inspected and the results (e.g., ASLF-1, touchdown zone, and centerline lighting, Rwy 11 checked satisfactory). For lighting that supports lower approach minima, on commissioning or reconfiguration inspections only, list the relevant SIAP(s). 6. Block 6 - Flight Inspection Data

a. NDB. Complete Items (4) – (10) below using the drop-down menu to select the appropriate entry. An Unsatisfactory condition requires an explanation in Remarks.

(1) Radio Class Code. Enter the applicable code as it appears on the AVNIS data sheet. Identify UHF facilities by adding "UHF." If inspecting the DME only of an NDB/ DME, leave blank.

(2) Frequency. Enter the frequency of the NDB.

(3) DME Channel. DME channel, when applicable.

9/28/09 8240.36M Appendix 5

(4) Identification

(5) Coverage

(6) Station Passage

(7) Interference

(8) Oscillations

(9) Standby Equipment

(10) Voice. UNSAT must be entered if one or more voice capabilities is OT.

(11) Bearing Accuracy. Required for UHF homing beacons. For other facilities, this field may be left blank.

(12) Standby Power

b. Direction Finding. Any unsatisfactory conditions identified on the report will be explained in Remarks.

(1) Station Passage. Select appropriate entry from drop-down menu. If not required, leave blank.

(2) Standby Power. Select appropriate entry from drop-down menu. If not checked, leave blank.

(3) Checkpoint. For AFIS, leave blank. For manual, describe checkpoints in Remarks.

(4) Aircraft Altitude. Enter the aircraft's altitude over the checkpoint, divided by 100 (e.g., "50" for 5,000 ft).

(5) Aircraft Distance. Enter the distance of the aircraft from the antenna to the nearest mile.

(6) Bearing/ Aircraft. Enter the aircraft's magnetic azimuth, to the nearest degree from the direction finding (DF) antenna.

(7) Bearing/ DF. Enter the bearing, to the nearest degree, issued by the controller.

(8) Bearing/ Error. Enter the difference between the aircraft azimuth and the bearing issued by the controller to the nearest whole degree (e.g., aircraft azimuth 331, issued bearing 333, the error is -2).

(9) Frequency Used. Enter the frequency used to obtain the DF bearing.

Note: Whenever an alignment orbit is flown, it may require several pages of DF checkpoints to satisfy the requirements of a complete orbit.

8240.36M Chg 1 5/30/11 Appendix 5

c. Visual Aids. Multiple lighting systems for one airport may be reported on one form; however all items in this field must be common to all runways listed on one report. If these provisions cannot be met, complete separate forms.

Note: Complete Items (4) – (11) below using the drop-down menu to select the appropriate entry. An Unsatisfactory condition requires an explanation in Remarks.

(1) Facility Inspected. Select the appropriate box/ boxes to indicate the light system(s) inspected. If the visual system inspected is not listed, use the “Other*” box and describe in Remarks. Lighting system will be described in detail in the Remarks section. (Example: “ALS” box checked, Remarks: “ALSF-2, HIRL, REILS commissioned SAT”.)

(2) Runway(s) Served. Enter the designator(s) to the runways served by the lighting system(s) being reported.

(3) Glide Slope Angle

(a) Enter the commissioned angle and the angle determined during the inspection (Example: 3.00/ 2.95).

(b) When the commissioned angle is unknown and/or the angle is not determined during the inspection, enter an asterisk in the "glide slope angle" block (e.g., */ *) and explain in "Remarks".

(c) Use the drop-down menu and select the appropriate entry.

(d) For PAPI(s) systems, report individual box angles in Remarks. (Example: For a 2-box system, enter: Box 1 = 3.25, Box 2 = 2.75. For a 4-box system, Box 2 and Box 3 angles required; Box 1 and Box 4 may be reported when measured.)

(4) Intensity

(5) Angular Coverage

(6) Sequence Flashers

(7) Obstacle Clearance (VGSI)

(8) Focus and Adjustment

(9) Coincidence (PAR/ ILS/ MLS)

(10) Runway Lights

(11) Radio Control System

d. Communications. Select the appropriate box/ boxes to indicate the communication service inspected. If the communication service inspected is not listed, use the “Other*” box and describe in Remarks.

The “Other*” box must be checked in cases where Pilot-to-Forecaster (P/R) or Combined Station Tower (CS/ T) was checked. Several frequencies may be listed on one line when all the results checked in the fields to the right are common to all frequencies listed. Indicate status by using the drop-down menu to select the appropriate entry.

9/28/09 8240.36M Appendix 5

A5-5 (and 6)

Flight Inspection Report—NDB, DF, Visual Aids, Communications

FAA Form 8240-5

This Page Intentionally Left Blank

Appendix 6 - PAR

9/28/09 8240.36M Appendix 6

Appendix 6. Flight Inspection Report--Precision Approach Radar,

GPN-22/ TPN-25 Continuation Sheet, TPN-22 Continuation Sheet

FAA Form 8240-6 Complete one FAA Form 8240-6, Precision Approach Radar, per runway identifier. When necessary, complete the appropriate PAR Continuation Sheet. 1. Block 1. Flight Inspection Report Header. Complete IAW Chapter 2, Paragraph 12. Exceptions:

a. Identifier (Ident). Enter the ident listed in AVNIS for the specific runway. Report only one runway identifer per report.

b. Runway. Enter the applicable runway designator 2. Block 2. Crew Information – Complete IAW Chapter 2, Paragraph 12. 3. Block 3. Facility Information. Indicate facility/ component inspected status or as left condition as appropriate. Use the drop-down menu to select the appropriate entry for the following fields:

a. Controller Performance

b. ILS/ MLS/ VGSI Coincidence

c. Standby Equipment

d. Standby Power

e. Lighting System(s)

f. Frequencies Used. List the frequencies inspected in the appropriate block. If additional space is needed, enter in Remarks.

g. Facility Status. Complete IAW Chapter 2, Paragraph 12m.

h. Published Angle. Enter the "Published Angle" commissioned angle.

i. Published Alternate Angle. Enter the published alternate angle if one is approved.

j. Equipment Type. Enter the type of equipment inspected (Example: MPN-14K, GPN-22, or TPN-19).

8240.36M 9/28/09 Appendix 6

4. Block 4. Generic PAR Approach Run Configurations. Do not enter data in this field when using a PAR Continuation Sheet for other than generic PAR(s).

a. Run: Cursor designation.

b. Moving Target Indicator (MTI). Select the appropriate box to indicate if the MTI feature was used during the approach.

c. Polarization. Select the appropriate box to indicate the type of polarization used during the approach for circular polarization (CP)/ Rain or linear polarization (LP)/ Clear).

d. Desired TX Configuration

e. Transmitter Inspected. From the drop-down menu, select the appropriate entry.

f. Angle (Actual Angle). Enter the measured PAR angle for each transmitter that was checked. If the “Actual Angle” was not determined, leave blank.

g. SAT/ UNSAT. Use the drop-down menu to select the appropriate entry.

h. The "Checks" columns show which runs are required to satisfy commissioning and periodic requirements. 5. Block 5. NOTAM(s). Complete as shown in Chapter 3, Paragraph 21d. 6. Block 6. Remarks. Complete as defined in Chapter 3. Enter additional remarks, such as:

 When PAR equipment has been replaced or when a major modification has been performed.

 When MTI is required on the final approach. (This requirement does not constitute a facility restriction.) 7. Block 7. Flight Inspection Data:

a. Azimuth Radar. For each transmitter type inspected, select the drop-down menu for the parameter checked. Select the appropriate entry for inspection results.

b. Elevation Radar. Glide Slope Alignment, Range Accuracy and Coverage. For each transmitter type inspected, select the drop-down menu for the parameter checked. Select the appropriate entry for inspection results.

9/28/09 8240.36M Appendix 6

8. Flight Inspection Report--Precision Approach Radar Continuation Sheets. When required, complete a separate form for each runway inspected.

Note: Abbreviations used in FAA Forms 8240-6 continuation sheets are as follow:

FTC - Fast Time Constant

ACQ - Acquisition

MTI - Moving Target Indicator

RWY - Runway

CK'S - Checks Required

NOR - Normal

BK UP - Back Up

AUTO - Automatic

COH - Coherent

NON-COH - Noncoherent

CFAR - Constant False Alarm Rate

ALS - Automatic Landing Subsystem

S/N - Serial Number

C - Commissioning

P - Periodic

RCVR CHAN, RC - Receiver Channel 8. Flight Inspection Report—Precision Approach Radar GPN-22/ TPN-25 Continuation Sheet

a. Block 1. General. Runway. Enter the runway designator.

b. Block 2. Computer-Generated Precision Approach Radar Run Configurations

(1) “R”s indicates the required configuration for each run.

(2) Select the appropriate blocks to indicate which configuration was inspected.

(3) Transmitter Used. Select the drop-down menu, and select the appropriate entry.

(4) Angle (Actual Angle). Enter the measured PAR angle for each transmitter inspected. If the “Actual Angle” was not determined, leave blank.

(5) RUN “SAT” or “UNSAT”. Use the drop-down menu to select the appropriate entry to indicate if the approach was satisfactory or unsatisfactory.

(6) The "Checks" columns indicate which runs are required to satisfy commissioning and periodic requirements.

8240.36M 9/28/09 Appendix 6

c. Block 3. Other Information. Enter Receiver Sensitivity, Clutter (rain) Reject, Transmitter Power, etc., in the blocks provided, as required in Order 8200.1, Paragraph 14.23b. Database Change (DBC). 9. Flight Inspection Report--Precision Approach Radar TPN-22 Continuation Sheet

a. Block 1 – General

(1) Runway. Enter the applicable runway designator.

(2) System Serial #. Enter the system serial number provided by Maintenance.

b. Block 2 - Computer Generated Precision Approach Radar Run Configurations.

(1) “R”s indicate the required configuration for each run.

(2) Select the appropriate blocks toindicate which configuration was inspected.

(3) The “Checks ” columns indicate which runs arerequired to satisfy commissioning and periodic requirements.

c. Block 3 – Program Data. Enter transmitter Output Power, Receiver Sensitivity, etc., as required in Order 8200.1, Paragraph 14.23c, Database Change (DBC).

5/30/11 8240.36M Chg 1 Appendix 6

Flight Inspection Report—Precision Approach Radar

FAA Form 8240-6

8240.36M Chg 1 5/30/11 Appendix 6

Flight Inspection Report—Precision Approach Radar

GPN-22/ TPN-25 Continuation Sheet

5/30/11 8240.36M Chg 1 Appendix 6

A6-7 (and 8)

Flight Inspection Report—Precision Approach Radar

Continuation Sheet

This Page Intentionally Left Blank

Appendix 7 - ILS Wksht

5/30/11 8240.36M Chg 1 Appendix 7

Appendix 7. Flight Inspection Report--ILS Worksheet, FAA Form 8240-7

and ILS Continuation Worksheet, FAA Form 8240-7-1 FAA Form 8240-7 must be used for all ILS flight inspections. When printed from the itinerary several blocks are pre-filled from the Facility Data Sheet, allowing the Mission Specialist to complete the form manually as needed. It must be retained with the corresponding recordings. The quantity of information entered In Blocks 1 - 11 is not mandatory. Block 12 should contain sufficient detail to explain the checks completed and the results found. 1. FAA Form 8240-7, ILS Worksheet

a. Block 1 - Location. Complete IAW Chapter 2, Paragraph 12.

b. Block 2 - Identification (Ident). Enter the 3-letter identifier of the ILS facility being inspected.

c. Block 3 - Runway No. Enter the runway number served by the ILS.

d. Block 4 – Date. Enter the date(s) as shown in Chapter 2, Paragraph 12.

e. Block 5 - Owner. Complete as shown in Chapter 2, Paragraph 12.

f. Block 6 - Type Check. Complete as shown in Chapter 2, Paragraph 12.

g. Block 7 - Facility Inspected. Place an “X” in the appropriate block(s) to signify components have been inspected.

h. Block 8 - Facility Status. Enter an “X” in the appropriate block for the localizer front course (F/C), glide slope (GS), and localizer back course (B/C) if inspected.

i. Block 9 - Localizer Data

(1) Width: Enter commissioned course width

(2) CAT: Enter Category

(3) B: Enter Broad alarm maximum width for tolerance applied

(4) S: Enter Narrow (Sharp) alarm minimum width for tolerance applied

(5) Dual Freq: Enter Yes or No

(6) Dual Tx: Enter Yes or No

(7) Voice: Enter Yes or No

(8) ESV: Enter Yes or No

(9) Back Course: Circle Y or N.

8240.36M 9/28/09 Appendix 7

j. Block 10 - Glide Slope Data

(1) Angle: Enter commissioned angle

(2) CAT: Enter category of facility

(3) H: Enter high angle limit (EF enter phase displacement in Remarks)

(4) L: Enter low angle limit (EF enter phase displacement in Remarks)

(5) GS Type: Enter glide slope equipment type (NR, CE, EF, etc.)

(6) Dual Tx: Enter “Y”es or “N”o

(7) ESV: Enter “Y”es or “N”o

(8) GRD Temp: Enter local area temperature used when conducting ILS-2 runs

(9) OAT: Enter outside air temperature used when conducting ILS-2 runs

(10) Baro: Enter barometric pressure used when conducting ILS-2 runs

(11) Alt: Enter MSL altitude ILS-2 runs were flown.

k. Block 11 - Notes: Enter any additional information that may be useful in interpreting the results of the flight inspection. For Best Fit Straight Line (BFSL), identify the runs used for BFSL reporting in Block 11.

l. Block 12 - Enter in chronological order the checks conducted and the results. Use enough detail that a qualified person can interpret the information and correlate the data to the flight inspection recordings.

(1) Run Number (#). Enter the numerical sequence of each check or test. RUN # entry does not have to match AFIS run number.

(2) Facility Configuration (CFG). Enter the number of the transmitter being inspected and the transmitter configuration code as listed below:

Localizer Transmitter Configuration Code

Normal N

Special Requirements Z

Alignment Alarm Left L

Alignment Alarm Right R

Course Width Wide W

Course Width Narrow S

RF Power Alarm P

Localizer, CRS Wide, CLR Wide B

Localizer, CRS NAR, CLR Wide C

9/28/09 8240.36M Appendix 7

Glide Slope Transmitter Configuration Code

Normal N

Wide W

Wide and CLR Demodulation B

Narrow S

Dephase Advance A

Dephase Retard R

Attenuate Middle Antenna M

Attenuate Upper Antenna U

Low Angle Alarm L

High Angle Alarm H

RF Power Alarm P

Special Requirements Z

Transverse Structure (FAF ALT) T

Phase Verification Main Sideband Advance Phase PSA

Phase Verification Main Sideband Retard Phase PSR

Phase Verification Middle Antenna Advance Phase PMA

Phase Verification Middle Antenna Retard Phase PM

Waveguide Glide Slope Configuration Code

Main Sideband Advance MA

Main Sideband Retard MR

Upper Auxiliary Attenuate UZ

Upper Auxiliary Advance UA

Upper Auxiliary Retard UR

Lower Auxiliary Attenuate LZ

Upper and Lower Waveguide Advance ULA

Upper and Lower Waveguide Retard ULR

Main Waveguide Feed Advance FA

Main Waveguide Feed Retard FR

Lower Main Feed Attenuate LMZ

Upper Main Feed Attenuate UMZ

(3) The remaining columns are intended for use as designated. They may be altered if necessary.

(4) Remarks/ Other Data. Enter notes explaining exceptional runs.

8240.36M 9/28/09 Appendix 7

Suggested abbreviations to be used when completing this form:

RWY - Runway

FREQ - Frequency

CW - Commissioned or measured Course Width

CAT - Category of ILS

CE - Capture Effect

NR - Null Reference

SBR - Sideband Reference

EH - Endfire Short

ED - Endfire Standard

EU - Endfire, Upslope Version

WG - Waveguide

ANGLE - Commissioned Glidepath

GND TEMP - Ground Temperature

OAT - Outside Air Temperature

BARO - Barometric Altimeter Setting

ALTITUDE - Altitude to Fly on ILS-2

PW - Path Width

PA - Path Angle

ALN - Alignment

190 A - 190 Microamp Angle

Mod - Modulation

90 Hz Sym - Symmetry of 90 Hertz side of width

SBP - Structure Below Path

Z1 - Localizer & Glide Slope Structure in Zone 1

Z2 - Localizer & Glide Slope Structure in Zone 2

Z3 - Localizer & Glide Slope Structure in Zone 3

Z4 - Localizer Structure in Zone 4

Z5 - Localizer Structure in Zone 5

POL - Polarization

150 CLR - Minimum localizer clearance on 150 Hz side of localizer

90 CLR - Minimum localizer clearance on 90 Hz side of localizer

2. FAA Form 8240-7-1, ILS Continuation Worksheet

a. Block 1 - Notes. Enter any additional information that may be useful in interpreting the results of the flight inspection.

b. Block 2. Complete as detailed above in Paragraph 1l, Block 12.

5/30/11 8240.36M Chg 1 Appendix 7

Flight Inspection Report—ILS Worksheet

FAA Form 8240-7

8240.36M Chg 1 5/30/11 Appendix 7

Flight Inspection Report—ILS Continuation Worksheet

FAA Form 8240-7

Appendix 8 - ILS

9/28/09 8240.36M Appendix 8

Appendix 8. Flight Inspection Report--Instrument Landing System

FAA Form 8240-8 FAA Form 8240-8, Instrument Landing System, is used to report all the components or conditions of an instrument landing system (when necessary). For Transponder Landing Systems (TLS(s)), separate forms are required for each runway or separate approach procedure. This form will also be used to report an ILS SIAP Amendment, allowing the tracking of ILS procedure changes using facility Ident.

Note: Commissionings of visual aids, NDB(s), and after accident reports on NDB(s) must be reported on FAA Form 8240-5. 1. Block 1 - Flight Inspection Report Header. Complete IAW Chapter 2, Paragraph 12. Exceptions:

a. Runway. Enter the applicable runway designator

b. Category. Enter the lowest minima performance category of the facility (I, II, III). 2. Block 2 - Crew Information – Complete IAW Chapter 2, Paragraph 12. 3. Block 3 – Facility Information. Select the drop-down box and enter “Inspected,” “Required/ Not Inspected,” or if not required, leave blank.

a. Localizer

b. Offset (Offset Localizer)

c. Glideslope

d. LDA

e. SDF

f. TLS (When TLS is inspected, use Localizer and Glide Slope fields above to indicate which components are checked.)

g. Other*. Explain in Remarks.

h. DME. ILS DME: Select the appropriate entry for inspection results. When the DME for an ILS approach is provided by a VOR/ DME, VORTAC, or TACAN, enter the facility ident, type (e.g., BLV TAC), and inspection results.

i. Compass Locator. If the identifier of the NDB is different from the ILS (compare the broadcast idents, not the AVNIS idents), enter the identifier. If more than one NDB is a component of the ILS system, report the additional NDB(s) in the Remarks block.

8240.36M 9/28/09 Appendix 8

j. Lighting System (All lighting required to support the lowest authorized visibility)

k. 75 MHz Markers. Complete IAW Chapter 3, Paragraph 21j.

l. SIAP(s). Complete IAW Chapter 3, Paragraph 21g.

m. Publications (Check IAW Order 8200.1, Paragraph 4.34f).

n. Commissioned (Com’d) Width. Enter the tailored or standard course sector width.

o. Commissioned (Com'd) Angle. Enter the commissioned angle.

p. Glide Slope Type. Enter the type of glide slope (e.g., NR, SBR, etc.)

q. Facility Status (F/C, G/S, B/C). Status will be assigned to all components inspected. For internationally owned facilities, leave blank and in Remarks add, “Host nation assigns status.” (An exception to international status may be by MOA.)

r. ILS Classification System. The classification system is a comprehensive method of describing ILS performance, including facility performance provided by Airway Facilities and operational requirements from Air Traffic. A facility’s “Class” of performance is defined by using three characters. Flight inspection will report two of the three characters based on facility performance. When the inspection warrants a change in facility classification, FAA Form 8240-20 must be submitted to Data.

(1) First Field: I, II, or III: Select the category the facility is assigned after the performance requirements are proven by Flight Inspection. (CAT II/ III will not be assigned until the CAT II/ III Procedure passes flight inspection.)

“Special Authorization CAT II Operations to RVR 1600 or 1200” SIAP type inspections: When Flight Inspection Operations checklist items are Satisfactory, enter in Remarks, “This facility supports Facility Performance Class II.” When published, the “Performance Class” field on the Facility Data Sheet will be changed by the Aeronautical Information Specialist from CAT I to CAT II. For future reports, enter CAT II into the ILS Classification System block.

(2) Second Field: A, B, C, T (Threshold), D, or E: Select the character that defines the ILS point to which the localizer conforms to the Facility Performance CAT III course structure tolerances.

Note 1: Performance classification of “D” and “E” must be determined solely by rollout procedures.

Note 2: Satisfactory comparability between rollout and low approach (50 ft): Low approach method may be used for subsequent classification.

Note 3: If the rollout check has been accomplished and documented on the data sheet as “U4/ 5” or “Q4/ 5”, do not report an ILS classificationcode inside Point T.

References:

ICAO Annex 10, Facility Performance CAT III standards FAA Order 6750.24, Appendix 2 FAA Order 8400.13, Appendix 1

9/28/09 8240.36M Appendix 8

(3) Inspection Criteria. When the inspection is performed to a higher standard than the official category because it has been published “Special Authorization CAT II Operations to RVR 1600 or 1200” SIAP, enter the higher standard category. If the facility is not inspected to a higher standard, leave blank.

(4) Rollout. When rollout procedures are established IAW Order 8200.1 for any localizer, document the rollout code. Select the drop-down menu and enter the appropriate code. The available codes include:

(a) S = Rollout accomplished; Rollout and the low approach meet CAT III comparability tolerances.

(b) U4 = Rollout accomplished; Zone 4 results do not meet Category II/ III tolerances.

(c) U5 = Rollout accomplished; Zone 5 results do not meet Category III tolerances.

(d) R4 = Rollout required for evaluation of Zone 4 and Zone 5. Rollout was accomplished; ground results meet Category II/ III requirements but do not compare with results of the 50 ft run in Zone 4.

(e) R5 = Rollout required only for evaluation of Zone 5. Rollout was accomplished; ground results meet Category III requirements; comparison with the 50 ft run was Satisfactory in Zone 4 but Unsatisfactory in Zone 5. 4. Block 4 - NOTAM(s). Complete IAW Chapter 3, Paragraph 21d. Restriction information for NDB(s) used only as Compass Locators must be reported. This restriction status must be entered in the Remarks section of the ILS AVNIS Facility Data Sheet. 5. Block 5 - Remarks. Complete IAW Chapter 3.

a. 75 MHz Marker Beacon(s). See Chapter 3, Paragraph 21.

b. Clearance Below Path. When evaluating clearances to runway threshold on CAT I glide slopes with runway centerline localizers, add Remark, “Clearance Below Path checks to Threshold are “Satisfactory”/ “Unsatisfactory”.

c. Localizer Course Width/Clearance Comparability (Procedure 1 or Procedure 2). Document comparability check results on FAA Form 8240-20. Add Remark, “Course width and clearance comparability verified from an altitude of XXXX ft MSL up to XXXX ft MSL, using procedure X, IAW FAA Order 8200.1, Paragraph 15.21h”, or “Course width and clearance checks must be conducted at an altitude of XXXX ft MSL”.

d. Report localizer phasing (e.g., enter the start/ stop distance from the localizer antenna, the course sector side (90 Hz or 150 Hz), the offset from centerline (in degrees), and the MSL altitude flown).

e. Distance references other than standard used in AFIS require a remark indicating location of distance reference and which reported data is affected by this reference.

8240.36M Chg 1 5/30/11 Appendix 8

6. Block 6 – Instrument Landing System Data- Azimuth (Part I). When type of inspection requires localizer data to be reported, complete this block. Enter results of the check in the appropriate transmitter column. If the localizer transmitter cannot be determined, indicate in Remarks, “LOC TX unknown” and use TX 1 column.

a. ILS-1 Altitude. Leave blank unless an altitude other than the Lower Standard Altitude (LSA) or the established altitude annotated on the datasheet is flown. A comment must also be added in the Remarks section of the report explaining the deviation from LSA or the established altitude. FAA Form 8240-20 will be required if establishing an altitude other than LSA or changing from a previously established true altitude. FAA Form 8240-20 is not required for weather or ATC deviations.

b. TX1/ TX2 CD (Code) Column. Under the appropriate transmitter number enter: "X" for any out-of-tolerance condition found and not corrected during the inspection "C" for any out-of-tolerance condition found and corrected during the inspection. “SS” when structure is “SAT” per Order 8200.1, Paragraph 15.51a. “CS” when clearance is “SAT” per Order 8200.1, Paragraph 15.51c.

Note: An “X” or “C” is not to be entered for any out-of-tolerance found in Zone 4 and 5 on a CAT I localizer (Zone 5 for Category II localizer) when the structure is analyzed for the purpose of defining a facility’s “Class” of performance.

c. TX1/ TX2 Initial Column. Enter the "as found" operating condition in this column, if this parameter was changed or adjusted during the inspection.

d. TX1/ TX2 Final Column. Enter the operating condition at the completion of the inspection. (Use this column to report the results of after accident checks.)

e. Course Width. Enter the measured, normal course sector width.

f. Symmetry. Enter the percent of symmetry of the 90 Hz side.

g. Modulation. Enter the "on course" modulation level in percent.

h. Clearance 150. Enter the minimum value in microamps and the degrees from the course on the 150 Hz side (Front or Back). (Example: 180/ 20.0 means the minimum clearance was 180A at 20.0 from the course.)

Note: Reporting the azimuth to a tenth of a degree to more accurately identify the minimum clearance value is permissible.

When a facility is restricted, enter the minimum clearance value found in the unrestricted area in Block 6. In Remarks, report the minimum clearance found within the restricted area (except when restriction is based on terrain or obstacles).

Note: Do not report the algebraic sign applied to clearances by AFIS.

For a TLS, indicate “S” for Satisfactory or “U” for Unsatisfactory. Explain Unsatisfactory conditions in Remarks. Clearance plots are not required for TLS.

i. Clearance 90. Enter the 90 Hz side results as shown in Subparagraph 6h above.

j. Course Structure - Z1, Z2, Z3, Z4, Z5. Report the maximum course displacement in microamperes and the distance from the threshold. (Report distance from the antenna on backcourse.) (Example Z2: 5/ 0.7 indicates the displacement was 5 µA at 0.7 nm.)

9/28/09 8240.36M Appendix 8

When a facility is restricted from a point in a zone, enter the maximum course displacement in the unrestricted portion of the zone in Block 6. Report the maximum structure found within the restricted area in Remarks.

If distances are referenced to the MAP note in Remarks. When necessary to more accurately locate a structure value in a particular zone, report mileage to the nearest hundredth.

(1) When zones have tolerances which have linear rates of change, report the structure closest to the tolerance limit.

(2) Report the out-of-tolerance furthest from the threshold, antenna (back course), or missed approach point. Report additional out-of-tolerance structure closer to the threshold, antenna (back course), or missed approach in Remarks, if appropriate.

k. Course Structure Rollout. Zone 4 and 5 structure, which is analyzed for the purpose of defining a facility’s “Class” of performance must be reported unless restricted or the data sheet indicates a rollout code of “U4/ 5” or Q4/ 5”. The zones used to identify the normal “Category” of the system must be used to assign facility class. For inspections where Zone 4 and Zone 5 structure are evaluated both through rollout and airborne (50 ft), report the rollout results in this field and the airborne results in Remarks.

l. Vertical Polarization. Enter “S” if Satisfactory or “U” if Unsatisfactory. Enter microamp displacement for unsatisfactory condition in Remarks.

m. Alignment. Enter the course displacement in microamperes, add suffix “L” (left) or “R” (right) from designed course. (Example: 3R is 3 µA right of the course. Enter “CL” (centerline) for no alignment error.)

LDA(s) oriented to a non-descript point-in-space must be reported either Satisfactory (S) or Unsatisfactory (U) (When visual checkpoints are inadequate and AFIS runway updates are impractical).

n. Identification. Enter "S" if Satisfactory or "U" if Unsatisfactory.

o. Power Ratio. Enter the power ratio value in dB.

p. Localizer Only Structure. Report localizer only approach final segment maximum structure. Report the structure closest to the tolerance limit (Example: localizer only structure 14/ 0.4 miles). 7. Block 7 - Instrument Landing System Data – Glide Slope (Part I)). When the type of inspection requires Glide Slope data to be reported, complete this block. Enter the results of check in the appropriate transmitter column. If the Glide Slope transmitter cannot be determined, indicated in Remarks “G/ S TX unknown” and use TX 1 column.

a. ILS-2 Altitude. Leave blank unless an altitude other than the established altitude corrected to true is flown. A comment must also be added in the Remarks section of the report explaining the deviation from the established true altitude. FAA Form 8240-20 will be required if establishing an altitude other than LSA or changing from a previously established altitude. FAA Form 8240-20 is not required for weather or ATC deviations.

8240.36M 9/28/09 Appendix 8

b. TX1/ TX2 CD (Code) Column: “X” for any out-of-tolerance condition found and not corrected “C” for any out-of-tolerance condition found and corrected “SS” when structure is “SAT” per Order 8200.1, Paragraph 15.51a.

c. TX1/ TX2 Initial Column. Enter the “as found” operating condition in this column, if this parameter was changed or adjusted during the inspection.

d. TX1/ TX2 Final Column. Enter the operating condition at the completion of the inspection. (Use this column to report the results of after accident checks.)

e. Angle. Enter the measured, actual glidepath angle.

f. Modulation. Enter the “on path”modulation level in percent.

g. Width. Enter the width of the glidepath envelope in Normal.

h. Structure Below Path. Enter the angle where 190 A of fly-up signal occurs in Normal.

i. Symmetry. Enter the 90 Hz side symmetry of the Normal glidepath envelope in percent.

j. Path Structure Z1, Z2, Z3. Report the maximum on-path displacement in microamperes for each zone and the distance from the threshold. (Example Z2 5/ 0.7 indicates the displacement was 5 A at 0.7 nm). If it is necessary to more accurately identify structure in a particular zone, report mileage to the nearest hundredth.

If a facility is restricted from a point in a zone, enter the maximum on-path displacement in the unrestricted portion of the zone in this field.

(1) When zones have tolerances that have linear rates of change, report the structure closest to the tolerance limit.

(2) Report the out of tolerance furthest from the threshold. Report any additional out-of-tolerance structure closer to the threshold in Remarks, if appropriate.

k. Angle Alignment “B – C”. This value represents the worst (with respect to tolerances) average deviation of Zone 3 best fit straight line angle from commissioned glide slope angle, as measured from Point B to Point C. Report polarity of displacement + or - (Example: +27/ 0.36 is +27 microamps at .36 nm).

Continue reading ↓ 120 of 180 passages shown