Radar Vectors
FAA Order Cancelled Issued Oct 26, 2009 AIR-200 71 pages Copy saved Nov 18, 2026

Order 8130.21G Procedures for Completion & Use Authorized Release Certificate, FAA Form 8130-3, Approval Tag

This document is no longer current. Cancelled by 8130.21H. Check the official source before relying on it.

Official source ↗ Open PDF

U.S. DEPARTMENT OF TRANSPORTATION

U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

National Policy

I

ORDER 8130.21G

10/26/2009

SUBJ: Procedures for Completion and Use of the Authorized Release Certificate, FAA Fonm 8130-3, Airworthiness Approval Tag

This order describes the procedures for completion and use of the Federal Aviation

ORDER 8130.21G

Administration (FAA) Authorized Release Certificate, FAA FOIm 8130-3, Airworthiness Approval Tag. The order describes the use of the fonn for domestic airworthiness approval, conformity inspections, and prepositioning; airworthiness approval of new products and articles; and splitting bulk shipments of previously shipped products and articles. It also provides guidance for the issuance of the fonn for approval for return to service of products and articles, the export airworthiness approval of products and articles, and the electronic exchange of the fonn.

~R~/

Frank P. Paski~z Manager Production and Airworthiness Division, AIR-2oo

Distribution: A-W (IRlFSNN) -3; A-X (CD/FS) -3; A-FFS-O (MAX) Initiated by: AIR-200 A-FAC-O (LTD); AMA-220 (10 copies); AMA-2S0 (10 copies) AFS-600 (3 copies); AEU-1001200

Table of Contents

Paragraph Page

Chapter 1. General Information

Chapter 1. General Information

1-1. Purpose of This Order … 1-1 1-2. Audience … 1-1 1-3. Where Can I Find This Order and FAA Form 8130-3? … 1-1 1-4. Cancellation … 1-1 1-5. Explanation of Policy Changes … 1-1 1-6. Effective Date … 1-2 1-7. Purposes For Which FAA Form 8130-3 Cannot Be Used … 1-2 1-8. Authorization to Issue FAA Form 8130-3 … 1-2 1-9. Information Systems and Automation … 1-3

Chapter 2. Domestic Airworthiness Approvals

Chapter 2. Domestic Airworthiness Approvals

2-1. General Information on Domestic Airworthiness Approvals … 2-1 2-2. Conformity Inspections … 2-2 Figure 2-1. Sample FAA Form 8130-3 for a Conformity Inspection … 2-3 2-3. Domestic Airworthiness Approval of New Products (Aircraft Engines and Propellers) … 2-3 Figure 2-2. Sample FAA Form 8130-3 for Domestic Airworthiness Approval

for an Engine … 2-4 2-4. Domestic Airworthiness Approval of New Articles … 2-4 Figure 2-3. Sample FAA Form 8130-3 for Domestic Airworthiness Approval

for a New Product or Article (Packing List) … 2-5 2-5. Domestic Airworthiness Approval of New Products and Articles at 14 CFR Part 121 and Part 135 Certificate Holders, and 14 CFR Part 145 Certificated Repair Stations … 2-6 Figure 2-4. Sample FAA Form 8130-3 for Airworthiness Approval When Issued

at a Distributor Facility … 2-7 2-6. Prepositioned Products and Articles … 2-7 Figure 2-5. Sample FAA Form 8130-3 for Identification of a Prepositioned

Figure 2-1: picture of page 2Figure 2-1 · page 2
Picture of the page from the copy saved here

Product or Article … 2-9 2-7. Splitting Bulk Shipments of Previously Shipped New Products and Articles … 2-9 Figure 2-6a. Sample FAA Form 8130-3 for Splitting Bulk Shipments … 2-11 Figure 2-6b. Sample FAA Form 8130-3 for Splitting Bulk Shipments (Separate

Sheet of Paper) … 2-11 2-8. Block-by-Block Instructions for Completing FAA Form 8130-3 for Domestic Airworthiness Approvals … 2-12 Figure 2-7. Sample FAA Form 8130-3 for a Direct Shipment Authorization … 2-16 Figure 2-8. Sample FAA Form 8130-3 for Airworthiness Approval for a New

Subcomponent for a PMA Article … 2-17

iii

Paragraph Page

2-9. Lost FAA Form 8130-3 Issued for Domestic Airworthiness Approvals.... 2-18 2-10. Reissuance of FAA Form 8130-3 for Domestic Airworthiness Approvals … 2-18

Figure 2-6a: picture of page 2Figure 2-6a · page 2
Picture of the page from the copy saved here

Chapter 3. Approval for Return To Service of Products and Articles

Chapter 3. Approval for Return To Service of Products and Articles

3-1. General Information on Approval for Return To Service … 3-1 Figure 3-1. Sample FAA Form 8130-3 for a Rebuilt Product or Article … 3-3 3-2. Approval for Return To Service After Maintenance, Preventive Maintenance, Rebuilding, and Alteration — Products and Articles … 3-3 Figure 3-2. Sample FAA Form 8130-3 for Approval for Return To Service … 3-5 Figure 3-3. Sample FAA Form 8130-3 for Dual Release Approval

for Return To Service … 3-6 3-3. Approval for Return to Service — Products and Articles … 3-6 3-4. Issuance of FAA Form 8130-3 for Used Products and Articles Removed from a U.S.-Certificated Aircraft for Installation on Another U.S.-Certificated Aircraft … 3-7 3-5. Block-by-Block Instructions for Completing FAA Form 8130-3 for Approval for Return To Service … 3-8 3-6. Lost FAA Form 8130-3 Issued for an Approval for Return To Service … 3-11 3-7. Reissuance of FAA Form 8130-3 Because of Typographical Errors on the Original … 3-11

Figure 3-1: picture of page 3Figure 3-1 · page 3
Picture of the page from the copy saved here

Chapter 4. Export Airworthiness Approvals of Aircraft Engines, Propellers, or Articles

Chapter 4. Export Airworthiness Approvals of Aircraft Engines, Propellers, or Articles

4-1. General Information on Export Airworthiness Approvals … 4-1 Figure 4-1. Sample FAA Form 8130-3 for Export Airworthiness Approval … 4-4 4-2. New Products and Articles … 4-4 4-3. Used Products … 4-4 4-4. PMA Articles … 4-4 Figure 4-2. Sample FAA Form 8130-3 for Export Airworthiness Approval

for a New Subcomponent for a TSO Authorization Article … 4-5 4-5. Block-by-Block Instructions for Completing FAA Form 8130-3 for Export Airworthiness Approvals … 4-5 Figure 4-3. Sample FAA Form 8130-3 for a Direct Shipment Authorization for

Export … 4-10 4-6. Lost FAA Form 8130-3 Issued for Export Airworthiness Approvals … 4-11 4-7. Reissuance of FAA Form 8130-3 for Export Airworthiness Approvals … 4-11

Chapter 5. Electronic Use of the Authorized Release Certificate, FAA Form 8130-3, Airworthiness Approval Tag

5-1. Purpose of This Chapter … 5-1 5-2. Background on Electronic FAA Form 8130-3 … 5-1 5-3. General Procedures for the Use of Electronic FAA Form 8130-3 … 5-2 5-4. Data Requirements … 5-4

iv

v

Figure 4-1: picture of page 3Figure 4-1 · page 3
Picture of the page from the copy saved here

Paragraph Page

5-5. Use of the Electronic FAA Form 8130-3 … 5-4 5-6. Specific Requirements Other Than Those Listed in ATA Spec 2000, Chapter 16 … 5-5 5-7. User/Installer Responsibilities … 5-7 5-8. Sample Uses of Electronic FAA Form 8130-3 … 5-7 Figure 5-1a. Sample XML Fragment for an Electronic Export Airworthiness

Approval … 5-7 Figure 5-1b. Sample FAA Form 8130-3 for an Electronic Export Airworthiness

Approval … 5-9 Figure 5-2a. Sample XML Fragment for an Electronic Airworthiness Approval … 5-10 Figure 5-2b. Sample FAA Form 8130-3 for an Electronic Airworthiness Approval … 5-11 Figure 5-3a. Sample XML Fragment for an Electronic Conformity Airworthiness

Approval … 5-12 Figure 5-3b. Sample FAA Form 8130-3 for an Electronic Conformity

Airworthiness Approval … 5-13 Figure 5-4a. Sample XML Fragment for an Electronic Approval for Return To

Service … 5-14 Figure 5-4b. Sample FAA Form 8130-3 for an Electronic Approval for Return to

Service … 5-15 5-9. Intent to Use Electronic FAA Form 8130-3 … 5-16 Figure 5-5 Sample Letter of Intent for an Electronic Certification System … 5-16

Figure 5-1a: picture of page 4Figure 5-1a · page 4
Picture of the page from the copy saved here

Appendix A. Acronyms … A-1

Appendix A. Acronyms … A-1

Appendix B. Definitions … B-1

Appendix C. Administrative Information … C-1

Appendix D. FAA Form 1320-19, Directive Feedback Information … D-1

Chapter 1. General Information

1-1. Purpose of This Order. This order describes the procedures for completion and use of the Federal Aviation Administration (FAA) Authorized Release Certificate, FAA Form 8130-3, Airworthiness Approval Tag (FAA Form 8130-3). The order describes the use of the form for the following purposes:

Chapter 1. General Information

a. Domestic airworthiness approval, including conformity inspections, prepositioning of new products or articles pending approval, and splitting bulk shipments of previously produced products and articles;

b. Approval for return to service of products and articles; and

c. Export airworthiness approval of products and articles.

NOTE: For the purposes of this order, the term product refers only to aircraft engines and propellers.

1-2. Audience. FAA personnel, designees, production approval holders (PAH), air agencies, U.S. air carrier certificate holders, and distributors.

1-3. Where Can I Find This Order and FAA Form 8130-3?

a. You can find this order at http://www.faa.gov/regulations_policies/orders_notices/.

b. FAA Form 8130-3 may be obtained through normal distribution channels from the Logistics Center, AML-8000, P.O. Box 25082, Oklahoma City, Oklahoma, 73125. The telephone number is 405-954-8900 (ask for the FAA Forms Inventory Manager). FAA Form 8130-3 also is available from the Customer Care Center, AML-30, at 405-954-3793 or toll free at 1-888-322-9824, or may be obtained on the Internet at http://www.faa.gov/aircraft. The stock number for FAA Form 8130-3 is 0052-00-012-9005.

1-4. Cancellation. FAA Order 8130.21F, Procedures for Completion and Use of the Authorized Release Certificate, FAA Form 8130-3, Airworthiness Approval Tag, dated May 30, 2008, is canceled upon the effective date of this revision (that is, April 14, 2010).

1-5. Explanation of Policy Changes. This revision—

a. Reflects changes and updates appropriate references following publication of Production and Airworthiness Approvals, Part marking, and Miscellaneous Amendments; Final Rule in the Federal Register under docket number FAA-2006-25877.

b. Replaces parts and appliances with the term “article.”

c. Removes references to classes of products.

d. Deletes the term “newly overhauled” and associated guidelines from the description of work performed.

e. Revises acceptable methods for enabling traceability of FAA Form 8130-3 by permitting use of Block 3 of the form in combination with other information on the form.

f. Removes language pertaining to distributors that are accredited in accordance with Advisory Circular (AC) 00-56, Voluntary Industry Distributor Accreditation Program.

g. Combines and moves information on computer-generated forms, information systems, and automation to a new paragraph 1-9.

h. In Chapter 3, permits use of either the term “Inspected” or “Tested” in Block 12 rather than requiring that both terms be entered together.

i. Adds a requirement in Chapter 4 that for exported aircraft engines or propellers, the exporter include total time and if applicable, time since overhauled.

1-6. Effective Date. This Order is effective on April 14, 2010.

1-7. Purposes For Which FAA Form 8130-3 Cannot Be Used. FAA Form 8130-3 is intended to be issued for civil aeronautical products and articles by persons under the jurisdiction of the FAA. Its issuance by persons not described in Chapters 2 and 4 of this order, (i.e., FAA aviation safety inspectors (ASI) or FAA-authorized designees or delegations), or Chapter 3 of this order (i.e., certificate holders under 14 CFR parts 21, 121, 135, or 145) is not authorized. Further purposes for which the form cannot be used are as follows:

a. FAA Form 8130-3 is not a delivery or shipping document, nor should it be used for administrative purposes between two persons.

b. FAA Form 8130-3 may not be issued by organizations or individuals other than those approved/authorized by the FAA within the scope of such an approval/authorization.

c. Aircraft are not to be released using FAA Form 8130-3.

d. FAA Form 8130-3 does not constitute approval to install the product or article on a particular aircraft, aircraft engine, or propeller; however, it does help the end user to determine a product’s or article’s airworthiness approval status.

e. A mixture of production- and maintenance-released products and articles is not permitted on the same FAA Form 8130-3.

f. A mixture of products and articles released against approved and non-approved design data is not permitted on the same FAA Form 8130-3.

1-8. Authorization to Issue FAA Form 8130-3. The following persons may issue FAA Form 8130-3 in accordance with the appropriate chapter of this order:

a. FAA ASIs,

b. Persons with the appropriate function codes in accordance with FAA Order 8100.8, Designee Management Handbook (Order 8100.8) when authorized by their Certificate of Authority (COA), or

c. Persons authorized in accordance with FAA Order 8100.15, Organization Designation Authorization (ODA) Procedures (Order 8100.15).

1-9. Information Systems and Automation.

a. FAA Form 8130-3 may be computer-generated for local reproduction, but must duplicate the format of the original Government-printed form. The overall form as designed must not be changed, nor may any words be added or deleted (with the exception of filling in the blanks). White is the preferred color for the paper; however, if another color is used, the information contained on the form must be legible. You may preprint the text on FAA Form 8130-3 that is required by this order. The size of blocks, in relationship to each other, may vary slightly, but all blocks must remain in their original location. FAA Form 8130-3 also may be reduced in overall size to reduce paper consumption, but not to the extent that it is no longer easily readable and readily recognizable. The details to be entered on the form may be either machine/computer-printed or handwritten using block letters and must be easy to read, with limited use of abbreviations. All entries on the form must be made in permanent ink and be in English. If a deviation to FAA Form 8130-3 becomes necessary, the FAA employee involved should ensure that the deviations are substantiated, documented, and concurred with by the appropriate supervisor. The deviations must be submitted to AIR-200 for review and approval.

b. Approval holders should develop procedures for managing information systems consistent with AC 21-35, Computer Generated/Stored Records. These procedures should include a secured electronic auditing system that reflects all system changes and a secured monitoring system that records all transactions by items such as part number, serial number (when applicable), and quantity shipped.

c. Automation and use of an electronic signature on FAA Form 8130-3 is allowed by all persons who issue the form; however, using automation and electronic signature does not relieve the designee or person authorized to issue FAA Form 8130-3 from verifying that the product or article conforms to FAA-approved design data and is in a condition for safe operation.

Chapter 2. Domestic Airworthiness Approvals

Chapter 2. Domestic Airworthiness Approvals

2-1. General Information on Domestic Airworthiness Approvals.

a. FAA Form 8130-3 is the preferred method for documenting the approval of products and articles considered approved by the Administrator. The FAA recommends that each PAH include FAA Form 8130-3 for all eligible product and article shipments. This will help the aviation authorities and the industry to ensure complete traceability, and ease the movement of products and articles through the aviation system. The PAH authorized representative is encouraged to issue FAA Form 8130-3 with each shipment while minimizing the quantity of forms for bulk shipments (for example, 500 turbine blades shipped on 1 form vs. 500 forms). Issuing FAA Form 8130-3 with all eligible product and article shipments enables the end users to determine airworthiness approval status of the products and articles. Only an FAA ASI or authorized designee/delegation is authorized to issue FAA Form 8130-3 for this function. Except as provided in paragraphs 2-2 and 2-6 of this order, products and articles not produced under an FAA production approval are not eligible to receive an FAA Form 8130-3. FAA Form 8130-3 does not constitute approval to install a product or article on a particular aircraft, aircraft engine, or propeller.

b. FAA Form 8130-3 must be completed as described in paragraph 2-8 of this order.

c. FAA Form 8130-3 must be correlated with the shipment. Additional copies of the original FAA Form 8130-3 may be provided upon request.

d. If FAA Form 8130-3 is issued as an airworthiness approval of a new product or article (this is to include conformity inspections, prepositioning, and splitting of bulk shipments), the issuer should retain a copy of FAA Form 8130-3 for no less than 5 years.

e. The copies of FAA Form 8100-1, Conformity Inspection Report (FAA Form 8100-1), and FAA Form 8130-3 may be retained in their original paper format or in a secure database, provided the database contains all of the information required on FAA Form 8130-3. An acceptable means of compliance is provided in AC 21-35 or AC 120-78, Acceptance and Use of Electronic Signatures, Electronic Recordkeeping Systems, and Electronic Manuals (when applicable). Duplicates of FAA Form 8130-3, including signatures retained in a database, do not need to be graphic images of the original documents.

f. Unique identification is required to enable or provide product or article traceability. The preferred method is a unique form tracking number in Block 3. However, if traceability is provided through other information on the form combined with a number in Block 3, this is also acceptable.

g. The signature of the person authorized to issue FAA Form 8130-3 may be applied electronically to Block 15 from domestic or international locations. With the exception of paragraphs 2-9 and 2-10(b), at the time the signature is authorized to be placed on FAA Form 8130-3, the person whose signature appears on the form must have direct access to the product or article to verify that it conforms to FAA-approved design data and is in a condition for safe operation.

NOTE: The time and location of the authorization of the form issuance may be different from the time and location of the printing of the form.

h. In the case where a product or article is presented for inspection for the issuance of FAA Form 8130-3, and the product or article is sealed in a package that does not afford a visible inspection, the authorized person must request to see the objective evidence to determine that the appropriate inspections were conducted and approved before the issuance of FAA Form 8130-3.

i. Products or articles received without an FAA Form 8130-3 must not be commingled with those received with FAA Form 8130-3. This is to preclude shipment of products and articles that were not received with an original FAA Form 8130-3. When more than one product or article is listed on a supplemental FAA Form 8130-3, the product or article does not need to be from the same quantity or shipment, as long as it was received with an original FAA Form 8130-3 and traceability has been maintained.

j. The User/Installer Responsibilities statements may be placed on either side of the form. If the statements are placed on the back side of the form, a note in Block 13 must reference that fact. When copies of the forms are generated, these statements must be provided with the copies.

2-2. Conformity Inspections. When requested on FAA Form 8120-10, Request for Conformity (FAA Form 8120-10), FAA Form 8130-3 is used to ship a prototype product or article. Any nonconformities/deviations relative to the product or article conformity inspection must have prior aircraft certification office (ACO)/designated engineering representative (DER), ODA, or FAA project manager acknowledgement of disposition. Before signing FAA Form 8130-3, any nonconformities/deviations must be appropriately acknowledged and dispositioned and be annotated in Block 13. Only an FAA ASI or authorized designee/delegation is permitted to sign the form. (Refer to figure 2-1 of this order.) When the request for conformity includes a quantity of articles in excess of those articles subject to the required certification, the tag for those excess articles should indicate they are prepositioned.

Figure 2-1. Sample FAA Form 8130-3 for a Conformity Inspection

2-3. Domestic Airworthiness Approval of New Products (Aircraft Engines and Propellers).

a. FAA Form 8130-3 can be issued for domestic shipments to identify the airworthiness approval status of new products produced under the provisions of 14 CFR part 21. The use of FAA Form 8130-3 for this purpose is optional, but the FAA recommends its use. When used for an airworthiness approval for new products (engines or propellers), the following statement must be entered: “AIRWORTHINESS APPROVAL — ENGINE [or PROPELLER].” (Refer to figure 2-2 of this order.)

Figure 2-2. Sample FAA Form 8130-3 for Domestic Airworthiness Approval for an Engine

b. Authorized FAA ASIs, persons with the appropriate function codes in accordance with Order 8100.8 when authorized by their COA, and persons authorized in accordance with Order 8100.15 may perform this function for new products. These persons must determine that the product meets the FAA-approved design data and is in a condition for safe operation before issuing FAA Form 8130-3. FAA Form 8100-1 will be used to document the conformity inspections.

Figure 2-2: picture of page 11Figure 2-2 · page 11
Picture of the page from the copy saved here

c. An FAA Form 8130-3 for domestic shipments of products to identify airworthiness approval cannot be used as an export approval. Exporters must meet the applicable requirements of 14 CFR part 21, subpart L, Export Airworthiness Approvals (refer to chapter 4 of this order).

2-4. Domestic Airworthiness Approval of New Articles.

a. FAA Form 8130-3 can be issued for domestic shipments to identify the airworthiness approval status of new articles produced by an FAA-approved PAH under the provisions of

14 CFR part 21. The use of FAA Form 8130-3 for this purpose is optional, but the FAA recommends its use. (Refer to figure 2-3 of this order.)

Figure 2-3. Sample FAA Form 8130-3 for Domestic Airworthiness Approval

for a New Product or Article (Packing List)

Figure 2-3: picture of page 12Figure 2-3 · page 12
Picture of the page from the copy saved here

b. A person must determine that the article meets the FAA-approved design data and is in a condition for safe operation before issuing FAA Form 8130-3. The FAA managing office must make the determination of whether an FAA Form 8100-1 has to be completed for each FAA Form 8130-3 issued based on the PAH’s quality system’s health and/or the designee’s previous history, experience, or performance, or if the information can be stored and retrieved in another format (for example, electronic database).

c. Standard parts produced under a production approval are eligible for the issuance of an FAA Form 8130-3 airworthiness approval. Use of FAA Form 8130-3 for this purpose is recommended, but not mandatory. The inclusion of FAA Form 8130-3 helps document the airworthiness and traceability of the standard part.

d. Issuance of FAA Form 8130-3 as an airworthiness approval does not constitute an export approval, because compliance with a specific country’s special import requirements may not have been verified.

e. An original FAA Form 8130-3 to document airworthiness approvals may be issued at PAH facilities, including PAH suppliers and associate facilities identified in the PAH’s approved procedures. The form also may be issued by a designated person at PAH suppliers with direct shipment authorization or associate facilities outside the United States, if the FAA finds there is no undue burden associated with the form’s issuance.

f. FAA Form 8130-3 will not be issued by non-PAH suppliers for products or articles shipped to their PAH’s facilities for use on production products or for proof of the PAH’s source inspection requirements at suppliers. If, however, the supplier has its own production approval for the products and articles, and the products and articles are part of another PAH’s higher level design, then FAA Form 8130-3 may be issued.

2-5. Domestic Airworthiness Approval of New Products and Articles at 14 CFR Part 121 and Part 135 Certificate Holders, and 14 CFR Part 145 Certificated Repair Stations.

a. New products and articles at repair stations certificated under 14 CFR part 145 (Repair Stations), the holder of a U.S. air carrier certificate operating under 14 CFR part 121 (Operating Requirements: Domestic, Flag, and Supplemental Operations), or 14 CFR part 135 (Operating Requirements: Commuter and On Demand Operations and Rules Governing Persons On Board Such Aircraft), with an approved continued airworthiness maintenance program, may be eligible to have an FAA Form 8130-3 issued as a domestic airworthiness approval. All other approvals must be issued in accordance with the appropriate chapter of this order.

b. When completing FAA Form 8130-3, the name and address of the organization where FAA Form 8130-3 was issued must be documented in Block 4, along with the PAH’s name in Block 13. (Refer to figure 2-4 and paragraph 2-8 of this order.)

Figure 2-4. Sample FAA Form 8130-3 for Airworthiness Approval When Issued

at a Distributor Facility

2-6. Prepositioned Products and Articles.

Figure 2-4: picture of page 14Figure 2-4 · page 14
Picture of the page from the copy saved here

a. General. FAA Form 8130-3 may be used to identify airworthiness approval status of prepositioned products or articles before type certificate (TC)/supplemental type certificate (STC) approval.

b. Applicability. Eligible products and articles are production products and articles that are conformed as part of an FAA certification project, and produced under a production certificate (PC) holder’s FAA-approved quality system in accordance with 14 CFR part 21, subpart G, Production Certificates, or subpart F, Production Under Type Certification Only.

c. System Requirements. The PC holder must have a procedure that tracks the configuration of the product or article from the manufacturer through shipment until the TC/STC is issued. The procedures must be adequate to ensure that the requirements of § 21.146(b) and (c) are met.

d. Completion of FAA Form 8130-3 for a Prepositioned Product or Article. The following persons may issue an FAA Form 8130-3 for a prepositioned product or article:

(1) An FAA ASI,

(2) A designated manufacturing inspection representative (DMIR),

(3) An ODA, or

(4) An authorized DAR employed by the PC holder, and

e. Supplemental Information. The following information will be listed in Block 13, Remarks: “Prototype products (articles) pending certification under FAA project number [enter number] that are not eligible for installation on in-service, type-certificated aircraft. Upon approval of the design data the product(s)/article(s) listed above are considered NEW and conform with approved design data and are in a condition for safe operation without further showing.” Block 14 will be marked as “Non-approved design data as specified in Block 13.” (Refer to figure 2-5 of this order.) When the request for conformity includes a quantity of products/articles in excess of those products/articles subject to the required certification, the tag for those excess products/articles should indicate that they are prepositioned.

f. Certification Issuance. After the TC/STC is issued, but before installation, the conforming product or article should be verified as incorporated into the design.

Figure 2-5. Sample FAA Form 8130-3 for Identification of a Prepositioned Product or

Article

2-7. Splitting Bulk Shipments of Previously Shipped New Products and Articles.

a. General.

(1) After an FAA Form 8130-3 is issued for a bulk shipment, a new FAA Form 8130-3 may be used to split bulk shipments of previously shipped new products or articles.

(2) Products or articles received without an FAA Form 8130-3 must not be commingled with those received with FAA Form 8130-3. This is to preclude shipment of products and articles that were not received with an original FAA Form 8130-3. When more than one product or article is listed on a supplemental FAA Form 8130-3, each product or article does not need to be from the same original shipment, as long as it was received with an original FAA Form 8130-3 and traceability has been maintained.

b. Eligibility and System Requirements.

Figure 2-5: picture of page 16Figure 2-5 · page 16
Picture of the page from the copy saved here

(1) Splitting bulk shipments is permitted when the specific products or articles were produced under an FAA production approval to include PAH associate facilities and PAH-approved suppliers having direct shipment authorization.

(2) The facilities authorized to split bulk shipments are PAHs, PAH associate facilities, distributors, PAH-approved suppliers having direct shipment authorization, and those certificate holders described in paragraph 3-1a of this order. This may include PAH associate facilities and PAH-approved suppliers that have direct shipment authorization that are located outside the United States. (This is not considered an export; the act of exporting is when the product or article is found to be airworthy, meets the special conditions of the importing country or jurisdiction, and is transferred from one CAA’s regulatory authority to another CAA’s regulatory authority.)

(3) An authorized facility as described in paragraph 2-7b(2) above must have a written procedure in place explaining how that facility will maintain control of products or articles when splitting bulk shipments.

(4) An authorized facility may split a bulk shipment of previously shipped new products or articles as many times as the original quantity as listed in Block 10 allows.

c. Splitting Bulk Shipments for Procedures and Documentation. For those shipments of products or articles required to be split, the following procedure will be used if an approved electronic system to issue supplemental FAA Forms 8130-3 for this purpose is not in place.

(1) Make a copy of the prior FAA Form 8130-3 received with the original shipment of products or articles. (Refer to figure 2-6a of this order.)

NOTE: If the user responsibilities statements are placed on the back side of the form, the copies of the forms must include these statements.

(2) Include the following written certifying statement (an example) or similar statement: “(Company name) certifies that [this/the attached] document is a true copy of the authorized release certificate. The prior authorized release certificate received by our facility is maintained on file pursuant to our document retention standards. That prior FAA Form Tracking Number is [OEM-549]. The new tracking number for this portion of the split bulk shipment is [S1-054321]. The number of products or articles being shipped under this certification is [500]. Signed [quality control/assurance manager] Dated [month day year]” (Refer to figure 2-6b of this order for an example.) A quality control/assurance manager from that facility must sign and date the written statement. You can include this statement in one of two ways:

(a) Attach the copied FAA Form 8130-3 to a separate sheet of paper. Indicate that the copied FAA Form 8130-3 that accompanies the products or articles is a “certified true copy of the original” maintained on file, or

(b) Apply a stamp form of the statement to the copied FAA Form 8130-3 and complete it.

(3) Maintain the prior FAA Form 8130-3 and a copy of the written “true copy” statement on file.

Figure 2-6a. Sample FAA Form 8130-3 for Splitting Bulk Shipments

Figure 2-6b. Sample FAA Form 8130-3 for Splitting Bulk Shipments (Separate Sheet of

Paper)

2-8. Block-By-Block Instructions for Completing FAA Form 8130-3 for Domestic Airworthiness Approvals.

a. Block 1. Approving National Aviation Authority/Country. FAA/United States. (Preprinted.)

b. Block 2. Authorized Release Certificate, FAA Form 8130-3, Airworthiness Approval Tag. (Preprinted.)

c. Block 3. FAA Form Tracking Number.

(1) Enter the number established by the numbering system. (Refer to paragraph 2-1g of this order.)

(2) The organization that splits bulk shipments of previously shipped products or articles received from a PAH must establish a new tracking number and enter that number on the certifying statement or on the supplemental FAA Form 8130-3. (Refer to paragraph 2-7c of this order.)

d. Block 4. Organization Name and Address.

Figure 2-6b: picture of page 18Figure 2-6b · page 18
Picture of the page from the copy saved here

(1) Enter the full name and physical address (no post office box numbers) of the organization or facility for which the form is being issued, and the PAH certificate or project number (for example, certificate No. LI1R 123K or X9MA123H), as appropriate. A logo or other identification of the organization is permitted if it can be contained within the block.

NOTE: In the case where FAA Form 8130-3 is issued at a PAH’s extension facility and that facility is issued its own project number by the geographic managing office, that project number will be used, along with the full name and address of the extension facility.

(2) When a supplier has direct shipment authorization from a PAH, or conformity inspections are performed on behalf of a PAH/applicant at the supplier’s facility, the following information must be entered:

(a) PAH name and address.

(b) Supplier name and address.

(3) If a supplier to a PAH produces and ships a product or article, the supplier must either have direct shipment authorization from a PC/PAH holder or hold a production approval for each article shipped. If the supplier holds its own production approval, and the products and articles were manufactured and are being shipped under that approval, the information required in paragraph 2-8d(1) must be listed.

(4) When completing FAA Form 8130-3 at a distributor’s facility, enter the name and the address of that facility.

e. Block 5. Work Order/Contract/Invoice Number. To facilitate customer traceability of the product or article, enter the work order number, contract number, invoice number, or similar reference number, and state the number of pages attached to the form, including dates, if applicable. If the shipment list contains the information required in Blocks 6 through 12, the respective blocks may be left blank if an original or true copy of the list is attached to the form. In this case, the following statement must be entered in Block 13: “This is the certification statement for the products and articles listed on the attached document dated … , containing pages … through … ” In addition, the shipping list must cross-reference the form tracking number located in Block 3.

f. Block 6. Item. When FAA Form 8130-3 is issued, a single item number or multiple item numbers (for example, same item with different serial numbers) may be used for the same part number. Multiple items must be numbered in sequence, although not necessarily beginning with the number one (for example, 0040, 0050, 0062, 0063). If a separate listing is used, enter “List Attached” (refer to paragraph 2-8e of this order for further instructions).

g. Block 7. Description. Enter the name or description of the product or article. Preference should be given to the term used in the instructions for continued airworthiness or maintenance data (for example, illustrated parts catalog, aircraft maintenance manual, or service bulletin (SB)).

h. Block 8. Part Number. Enter each part number of the product or article. In the case of an aircraft engine or propeller, the model designation may be used.

i. Block 9. Eligibility. Enter “N/A.”

j. Block 10. Quantity. Enter the quantity of each product or article shipped.

k. Block 11. Serial/Batch Number. If the product or article is required by 14 CFR part 45, Identification and Registration Marking, to be identified with a serial number, enter it here. Additionally, any other serial number not required by regulation also may be entered. If no serial number is entered in this block, enter “N/A.”

l. Block 12. Status/Work. The following table describes what to enter in a specific situation. Only one term may be entered in Block 12, which should reflect the majority of the work performed. The use of upper or lower case in this block does not matter.

Enter— For— “NEW” The production of a new product or article in conformity with the approved design data. “PROTOTYPE” The production of a new product or article in conformity with the non-approved design data.

m. Block 13. Remarks. The use of upper or lower case in this block does not matter.

(1) State any information in this block, either directly or by reference to supporting documentation, necessary for the user or installer to determine the airworthiness of the product or article. If necessary, a separate sheet may be used and referenced from the main FAA Form 8130-3. Each statement must clearly identify the product or article in Block 6 to which it relates. If there is no statement, state “none.”

(2) Below are examples of conditions that could necessitate a statement in this block. These statements may or may not be appropriate depending on the form’s purpose.

(a) “Prototype products (articles) pending certification under FAA project number [enter number] that are not eligible for installation on in-service, type-certificated aircraft. Upon approval of the design data, the product(s)/article(s) listed above are considered new, conform with approved design data, and are in a condition for safe operation without further showing.” Block 14 will be marked as “Non-approved design data specified in Block 13.”

(b) When a new FAA Form 8130-3 is issued to correct errors, the following statement must be entered: “This FAA Form 8130-3 corrects the error(s) in block(s) [enter block numbers corrected] of the FAA Form 8130-3 [enter original form tracking number] dated [enter original issuance date] and does not cover conformity/condition/release to service.”

(c) The purpose of the form (for example, airworthiness approval, conformity, prepositioning).

(d) Attachment when used. Attachments should include the form tracking number of the corresponding FAA Form 8130-3.

(e) Compliance with airworthiness directives (AD) or SBs.

(f) For TSO articles, enter the applicable TSO number.

(g) Information on life-limited parts (for example, total time, total cycles, time since new).

(h) Shelf-life data.

(i) Drawing number and revision level.

(j) Information needed to support shipment with shortages or reassembly after delivery.

(k) Any data not appropriate in other blocks.

(l) When used for conformity, the words “CONFORMITY INSPECTION” must be entered. In addition, an explanation of the product or article use (for example, pending approved data, TC pending, for test only) must be provided. Information concerning a

conformity inspection such as design data, revision level, date, project number, and special instructions as shown on FAA Form 8120-10 must be entered in this block.

(m) When issued at a supplier facility with direct shipment authorization from the PAH, the words “DIRECT SHIPMENT AUTHORIZATION” must be entered in Block 13, and the information from paragraph 2-8d(2) of this order must be entered in Block 4. (Refer to figure 2-7 of this order.)

(n) When FAA Form 8130-3 is issued at a distributor, enter the following statement: “The products/article(s) shipped under this approval was (were) produced by [insert PAH’s name].” (Refer to figure 2-4 of this order.)

(o) When used for an airworthiness approval for new products (engines or propellers), the following statement must be entered: “AIRWORTHINESS APPROVAL — ENGINE [or PROPELLER].” (Refer to paragraph 2-3 of this order.)

(p) When used for prepositioning, the following statement must be made (Refer to figure 2-5 of this order): “Prepositioned products (articles) were conformed to design data under FAA project number [enter number], for the issuance of a TC/STC modification of [enter make and model number]. Product(s)/article(s) conforming to design at issuance of the TC/STC is/are certified as airworthy and is/are in a condition for safe operation without further showing.”

(q) When used for airworthiness approval for a new subcomponent of a PMA/TSO authorization article higher assembly, complete FAA Form 8130-3 with the subcomponent information, and enter a statement in Block 13 indicating that the article is a subcomponent of a PMA or TSO authorization (for example, “This [insert part description] is a subcomponent of a(n) [FAA PMA article/TSO authorization]”) (Refer to figure 2-8 of this order).

Figure 2-7. Sample FAA Form 8130-3 for a Direct Shipment Authorization

1. App, ,,,in,Nod,,,,I A,i.d_

A , ~I, .. ·~. (, .. y,(,.,

FAA/United SI~l es

,.

Figure 2-7: picture of page 23Figure 2-7 · page 23
Picture of the page from the copy saved here

AUTHORIZED RELEASE CERTIFICATE

AUTHORIZED RELEASE CERTIFICATE

F..u. F .. -... 8UI_). AffiWORTHINESS APPROYAL l AC

~ . w;;~o. ·~ .. · ('.0' ... '" 1m … N … b .. : EI-erybody s .A..ilcmft 5upply Co .• 810 Red Baron Way • . A..i\)'wlt!K OK ~ ,1032 \VO 20 20

~. ''',III: .. 1'","",""..-: .. 10. Qa.nlifr. II. ~ .. hIB"'bN ... bt<: II.

\Ving1'!p NI.-\ N/A New

AIRWORTIIINESS . .>.f'I'RO\"AL-DlRECT SHIPMENT AUTIIORIZATION

AIRWORTIIINESS . .>.f'I'RO\"AL-DlRECT SHIPMENT AUTIIORIZATION

o 0_ , ","0<1 ... "odD'" bo BIod< 1~

[") "J'P"""'" ~ .. i .. , d •• _ ... ~ ... in . _,Ii~'H f..- , .... "" .... ,._. ON .. , .PI" .. · ... d"',,. d ... 'p .. ·mHl in nI .. k 11.

… , .. "'_ m 11_ >l … · .. k … ~n ... 1n HI .. k"

_d … l~.d bo Rlo<f: 1l .... , . .. _,H, .... '" ... , … ~i" TIr1. 14. Coolo J ,.<In-oJ … ,;.. •• p'" u .. d ... "'p<" .. ,I ... ,,-.. I.. •• , ['" … -• • p,..,.", tOO' … ~ .. , ... i .. .

D/'. IIR-0024~-C E

D/'. IIR-0024~-C E

IS. U". (uod y):

____ -L __ CA~ prJ3200S C-CC~ … L … ooj

U.~,.,I I"'I~I., · R""I'"">ilbilili",,

A In"peclol'

"n..-. ,~ . H' .... i ... ,oII .. r • .,., .... n' " .•• " .. "' ... ~ … "lOh ,h. _,; .. ,,01 "Jul.~o ... "." .un,· .. 'hio ... , . ... h ... ~~- oIill .. n" ,h •• ,h … -, … , .u'h .. ;, ~· 01 01" .... wh· .• · '1""&.-.1 in BI_ 1. I< ;" ", .. ,,;.1 ,h., ,h. 0, .. '1",,011 ... ""0'" ,h., ""' h .... " ·",01,;" ,,, .,,'h ... ~.· .«."b 9" ,"' … ,,,,,, '. » … , .. , f … ,h … d ... , ,, .ulli .. II,' 0111" ... w',,· ,,..,,ft.-.llu BI_I.

-

F~.I. F" ", ~ I .IO-J (oHll) N~N OO'l-Q(l-()I!-900'

Figure 2-8. Sample FAA Form 8130-3 for Airworthiness

Approval for a New Subcomponent for a PMA Article

n. Block 14. Airworthiness Approval.

Figure 2-8: picture of page 24Figure 2-8 · page 24
Picture of the page from the copy saved here

(1) Place a check in the “Approved design data and are in a condition for safe operation” box if the products and articles were manufactured using FAA-approved design data and found to be in a condition for safe operation. Checking this box and signing Block 15 means that the products and articles listed on the form meet the FAA-approved design data and are in a condition for safe operation.

(2) Place a check in the “Non-approved design data specified in Block 13” box when FAA Form 8130-3 is used for—

(a) Conformity of a prototype product or article certification program.

(b) Prepositioning products or articles before the issuance of a TC/STC.

o. Block 15. Authorized Signature. This space will be completed with the signature of the authorized person. Only an FAA ASI, authorized designee, or person approved to sign under an authorized delegation is authorized to sign this block. An alternative to a handwritten signature (for example, a computer-generated signature; refer to appendix B to this order for definition) is permitted only when authorized by the FAA. The approval signature must be

applied at the time and place of issuance and manually applied, except as provided in paragraph 2-1g of this order.

p. Block 16. Approval/Authorization No. Enter the approval/authorization number of the authorized representative/organization identified in Block 15. If signed by an FAA inspector, the authorization number is the applicable office identifier.

q. Block 17. Name. Enter the typed or printed name of the authorized representative or organization whose signature appears in Block 15.

r. Block 18. Date (m d y). Enter the date on which Block 14 is completed, or in the case of electronically generated forms, the date the conformity determination is made and the form is authorized to be issued. The date must be in the following format: first three letters of the month, two-digit day, and four-digit year, for example, Feb 03 2008. This does not need to be the same as the printing or shipping date, which may occur later. The use or omission of slashes, hyphens, or spaces in the date does not matter.

s. Blocks 19 through 23. Shade, darken, or otherwise mark to preclude inadvertent or unauthorized use.

2-9. Lost FAA Form 8130-3 Issued for Domestic Airworthiness Approvals. If a copy of an FAA Form 8130-3 is requested, a file copy of the original form may be provided by an authorized person, if available.

2-10. Reissuance of FAA Form 8130-3 for Domestic Airworthiness Approvals.

a. Reissuance by a PAH for Returned Products and Articles.

(1) The new products and articles returned to a PAH may be eligible for a new FAA Form 8130-3 if—

(a) The new products and articles were produced under the PAH’s production approval.

(b) The PAH maintains a procedure to accept products and articles back into its quality system.

(c) Tests and inspections are performed in accordance with procedures contained in the PAH’s quality system to determine that the returned product or article still meets the original type design it was produced under and is still in a condition for safe operation.

(2) If the conditions in paragraph 2-10a(1)(a) through (c) are met, a new FAA Form 8130-3 in accordance with chapter 2 of this order may be issued.

(3) If the original FAA Form 8130-3 is returned with the products and articles, the issuer should retain that form on file with (or have reference to) the new FAA Form 8130-3.

b. Reissuance Because of Typographical Errors on the Original. The original issuer may reissue FAA Form 8130-3 if there are typographical errors on the original.

(1) The recipient must provide a written statement and a copy of the incorrect FAA Form 8130-3 to the original issuer that indicates the errors.

(2) The request for a new FAA Form 8130-3 may be honored without reverification of the product or article condition. The new FAA Form 8130-3 is not a statement of current condition and should refer to the previous FAA Form 8130-3 in Block 13 by the following statement: “This FAA Form 8130-3 corrects the error(s) in Block(s) [enter block number(s) corrected] of the FAA Form 8130-3 [enter original form tracking number] dated [enter original issuance date] and does not cover conformity/condition/release to service.” The erroneous form must be marked as such. Both forms should be retained according to the retention period associated with the original.

Chapter 3. Approval for Return To Service of Products and Articles

Chapter 3. Approval for Return To Service of Products and Articles

3-1. General Information on Approval for Return To Service.

a. Air agencies certificated under 14 CFR part 145, or the holder of a U.S. air carrier certificate operating under 14 CFR part 121 or part 135, with an approved continued airworthiness maintenance program may issue an FAA Form 8130-3 for approval for return to service for a product or article maintained or altered under 14 CFR part 43, Maintenance, Preventive Maintenance, Rebuilding, and Alteration.

NOTE: The restriction in this order relating to the original issuance of the form does not apply when the form is used as a maintenance record and approval for return to service. Copies of the original form when used as a maintenance record or an approval for return to service may be provided to the owner/operator or others who require copies of maintenance records as prescribed by the applicable CFRs.

b. A PAH may issue an FAA Form 8130-3 for approval for return to service after rebuilding, altering, or inspecting its product in accordance with §§ 43.3(j) and 43.7(d). The use of FAA Form 8130-3 for this purpose is optional, but the FAA recommends its use. This will help aviation authorities and the industry to ensure complete traceability and ease the movement of products and articles through the aviation system. (Refer to paragraph 3-2a(2) and figure 3-1 of this order.)

NOTE: Rebuilt products and articles accomplished by a manufacturer may not be found acceptable by some European countries, because “rebuilt” is not included within the definition of “maintenance” as defined in 14 CFR part 1 or because the European system does not have a similar system that recognizes “rebuilt.” Therefore, when completing FAA Form 8130-3 for the purpose of “rebuilt,” refer to paragraphs 3-2a(3), 3-5m(3), and 4-5l.

c. FAA Form 8130-3 does not constitute approval to install a product or article on a particular aircraft, aircraft engine, or propeller.

d. Blocks 19 through 23 on FAA Form 8130-3 are used to indicate approval for return to service (along with the information contained in Blocks 1 through 13).

e. FAA Form 8130-3 must be completed as outlined in the Block-by-Block instructions in paragraph 3-5 of this order.

f. FAA Form 8130-3 must be correlated with the shipment. Additional copies of the original FAA Form 8130-3 may be provided upon request.

g. The following statements describe how long a copy of FAA Form 8130-3 completed for approval for return to service should be retained unless the regulatory requirements stipulate otherwise:

(1) If FAA Form 8130-3 is issued as an approval for return to service by an appropriately certificated organization, that is, part 121, 135, or 145, the issuer should retain a copy of FAA Form 8130-3 for a period of 2 years after the work is approved for return to service, unless the work is repeated or superseded. An air carrier’s own manual requirements may require a longer retention period.

(2) If a certificated repair station uses FAA Form 8130-3 as the approval for return to service for a major repair in accordance with 14 CFR part 43, the repair station should retain a copy of the document for 2 years.

h. The copies of FAA Form 8130-3 may be retained in their original paper format or in a secure database, provided the database contains all the information required on FAA Form 8130- 3, complies with AC 120-78 (when applicable), and is available for FAA review upon request. When FAA Form 8130-3 is issued for approval for return to service in accordance with this chapter, a copy of the original FAA Form 8130-3 that accompanied each shipment, or product or article must comply with the recordkeeping requirements of 14 CFR parts 43, 91, 121, 135, and 145. These forms must be retained by the facility where FAA Form 8130-3 is issued. Duplicates of FAA Form 8130-3, including signatures retained in a database, do not need to be graphic images of the original documents. However, when a supplemental FAA Form 8130-3 is issued as described by this order, traceability back through a system that ensures that the products and articles were received with their original FAA Form 8130-3 must be possible.

i. Many part numbers are applied in a nonpermanent manner (for example, ink stamp or paper label). In other cases, maintenance is required in areas where articles are permanently identified. During the maintenance process, these part numbers may be removed or otherwise obscured. If during maintenance the part number is removed or obscured, the persons performing the maintenance must document the part number and, if applicable, serial number, total time and cycles, heat code (if applicable), and any and all part markings on maintenance documents before performing the work. The article information must be reapplied after maintenance per acceptable practices. FAA Form 8130-3, when completed in accordance with this order, may be considered the article’s identification in order to identify the article.

j. Unique identification is required to enable or provide product or article traceability. The preferred method is a unique form tracking number in Block 3. However, if traceability is provided through other information on the form combined with a number in Block 3, this is also acceptable.

k. The signature of the person authorized to issue FAA Form 8130-3 may be applied electronically to Block 20 from domestic and international locations. At the time the signature is authorized to be placed on FAA Form 8130-3, the person whose signature appears on the form must have direct access to the products, articles, forms, and other data to monitor the process, perform spot-checks, and ensure that the work specified on the form was accomplished in accordance with 14 CFR part 43 and, in respect to that work, the items are approved for return to service.

l. The User/Installer Responsibilities statements may be placed on either side of the form. If the statements are placed on the back side of the form, a note in Block 13 must reference that fact. When copies of the forms are generated, these statements must be provided with the copies.

Figure 3-1. Sample FAA Form 8130-3 for a Rebuilt Product or Article

3-2. Approval for Return To Service After Maintenance, Preventive Maintenance, Rebuilding, and Alteration — Products and Articles.

a. Only those persons described in paragraph 3-1a and b, when authorized by § 43.7(c), (d), and (e), may issue an FAA Form 8130-3 for approval for return to service of products and articles that have undergone maintenance, preventive maintenance, rebuilding, or alteration, provided the applicable recordkeeping requirements of §§ 43.9, 91.417, 91.421, 121.380, 135.439, or 145.219 are met. The use of FAA Form 8130-3 for this purpose is optional, but the FAA recommends its use. This will help aviation authorities and the industry to ensure complete traceability and ease the movement of products and articles through the aviation system. (Refer to figure 3-2 of this order.)

(1) All work must be performed under the control of part 121 or part 135 certificate holders having a continued airworthiness maintenance program or an air agency certificated under part 145. This applies to all FAA-certificated repair stations, both domestic and foreign.

(2) A PAH may use FAA Form 8130-3 for approval for return to service of products and articles as set forth in §§ 43.3(j) and 43.7(d). The completion of Blocks 19 through 23 will be used when the PAH rebuilds or alters any product manufactured by it under a TC or PC, TSO authorization, PMA, or product and process specification issued by the Administrator. The PAH completes Block 19 by checking the appropriate box “Other regulation specified in Block 13.” Refer to paragraphs 3-5l and 3-5m(3).

(a) Documentation as outlined in § 43.9 ensures that a PAH has in place a method for tracking the rebuild and/or alteration work performed and who performed it. This documentation method should become part of the FAA-approved quality system.

(b) As a minimum, the PAH quality system should address the PAH’s procedures for rebuild and alteration that—

1) Dictate the data used for rebuilding and alteration. Section 43.7(d) requires that except for minor alterations, products or articles must be worked under technical data approved by the FAA. It is acceptable to rebuild using the same FAA-approved design data used for manufacturing. The PAH may alternatively develop data specifically for rebuilding, as long as that data is FAA-approved.

2) Identify by name and job title all persons authorized to return rebuilt or altered products and articles to service, to include signing of return-to-service documents.

3) Identify the records required for approval for return to service and how to complete them in compliance with § 43.9(a). Concerning the name and signature of the person approving the product/article for approval for return to service, the certificate type and number of the approving person must be documented as well. In the case of PAHs rebuilding their own products and articles, the certificate number is the assigned FAA project number (under 14 CFR part 21, subparts F, Production Under Type Certificate Only; K, Parts Manufacturer Approvals; or O, Technical Standard Order Approvals) or the PC number (under 14 CFR part 21, subpart G, Production Certificates).

(c) Section 43.7(d) authorizes the PAH to return to service any item worked on under § 43.3(j). Any employee of the PAH may therefore issue approval for return-to-service documents, but the PAH should deem them qualified and authorized in writing — the approval for return-to-service documents are signed as part of their approval. Issuing approval for return-to-service documents for rebuild and alteration activities is not a designee function. While the person issuing approval for return-to-service documents may also be an FAA designee, that person must not perform approval for return to service in a designee capacity or record a designee number on any approval for return-to-service document.

(3) When FAA Form 8130-3 is used as an approval for return to service to meet the terms and conditions of a bilateral agreement’s maintenance implementation procedures (MIP), the air agency or air carrier must check the two boxes in Block 19 stating “14 CFR 43.9 Return to Service” and “Other regulations specified in Block 13” and provide the appropriate information in Blocks 12 and 13. This is considered to be a dual release FAA Form 8130-3. (Refer to figure 3-3 to this order.)

(4) If another authority’s approved maintenance data are used to maintain products and articles and those data are not addressed in the provisions of a MIP, FAA Form 8130-3 should not be used.

b. In all cases, an appropriately authorized representative of the air agency, air carrier, or PAH in accordance with § 43.7(c), (d), or (e) must make the approval for return to service of products and articles.

c. European CAAs may recognize an approval for return-to-service FAA Form 8130-3 only from part 145 domestic repair stations or air carriers that also obtained a European Aviation Safety Agency (EASA) part 145 approval appropriately rated for the product or article at the time the product or article was approved for return to service. If a dual release is being applied to FAA Form 8130-3 to satisfy a European CAA or EASA, the air agency, U.S. air carrier, or FAA approval/certification number must be entered in Block 21, along with the following statement in Block 13: “Certifies that the work specified in Blocks 12/13 was carried out in accordance with EASA part 145, and with respect to that work, the component is considered ready for release to service under EASA part 145 Approval Number [insert number: EASA 145-XXX].”

Figure 3-2. Sample FAA Form 8130-3 for Approval for Return To Service

I. Appnning National Avlation 2. 3. Form Tracking Number: Authority/Country:

Figure 3-2: picture of page 32Figure 3-2 · page 32
Picture of the page from the copy saved here

F A.AJUnited States AUTHORIZED RELEASE CERTIFICATE 2004-664 fAA Form 8IJG-3. A IRW ORTHIN~SS APPROVAL TAG 4. Organization Name and Address: ,. 'York Order/Contract/invoice Number: Anyone's Repair Station, 1104 Wing Avenue, Anyplace, TX 22212 (PW8RW813J) W 8851

6. Ttem: 7. Descriptioll ; s. Pftrt Number: ,. Eli::ibility: '". Quantity: ". ScriQllBatch Number: 12. Stolmi\\'ork:

010 Actuator 69A321 N/A 1 3384-L REPAIRED

13. Remarks:

"The work specified has been accomplished in accordance with [insert type of manual or specification. number, and revision date 1-"

14. Certifies the items Idcntifloo above "'cre manufactured In conformity to: ". t2l 14 CFJ{ 43.9 Return to Sen1ce 0 Other regulation spedrled In Block 13

0 Appro\'ed design data and are In a oondilion for safe operatlon. Certifies that unless otherwise spectned In Block 13, the work Identified In Block 12 and descrIbed In Block 13 Was acctllnl'li<hoo In aCCtlrdanc~ wilh ntJ~ 14, Code of 0 Non-approH'd design data ~pectned In Block 13. Federal R~ulalloll'" psrt 43 and in respo,1 10 th_1 work, the lIelll' ar" al'pl'lln.:l f'" relurn to ~r\-ice . ". Authorized Signature: 16. AppronllAulhorlzatJoo No.: 20. Aulliortzed SIgnature: 21. ApprovaIICertlficaleNo.:

d¥d~ PW8RW813J

17. Name (Typed or PrInted): 18. Date (mdy): 22. Name (Typed or PrImed): 23. Date (m dy):

A. T nspector Oct 12 2007

User/lnsh1l1er Responsibilities

It is import.>"'t to Ulldcrsl .• nd that the e~ i stell ce of this documcnt alOlle does not automatically coll~tilutc uuthnrity tn install /lie purtiCOl11p(l11eIlIJaS5Cl11bly.

\Vhcrc llic user/installer pcrfonus >"wrk in accordann: with thc national regulatlons of au ai.J·ft·orthiuc~ authority different than the airworlliiness anthority of the country specified in Block 1, it Is essentlal that thc user/Installer ensures that hl~er airworthiness anthority accepts part~col1lponents/assemblies from the alr..-orthinC!;s authority of/lw conntry specified in Block 1.

Statements In Blocks 14 and 19 do not constltnte Installatlon rertinculon. In all cases, alrcran maintenance records must comain an Installation certlficatlonlssued In accordance with the natlonal regnlations by the nserilnstaller before llie aIrcraft may be nOftTI.

FAA Fum, 8130---3 (6---0J) NSK 0052·1)(1·012·9005

Figure 3-3. Sample FAA Form 8130-3 for Dual Release Approval for Return To Service

3-3. Approval for Return To Service — Products and Articles.

Figure 3-3: picture of page 33Figure 3-3 · page 33
Picture of the page from the copy saved here

a. Products and articles may be inspected and approved for return to service by persons described in paragraph 3-1a of this order. Issuance of FAA Form 8130-3 for this purpose is optional, but the FAA recommends its use. This will help aviation authorities and the industry to ensure complete traceability and ease the movement of products and articles through the aviation system. When used for this purpose, an air agency or air carrier must accomplish the inspection. FAA Form 8130-3 can be used for this purpose, provided the applicable recordkeeping requirements of §§ 43.9, 91.417, 121.380, and 135.439 are met and the quality system includes the following:

(1) Traceability to an FAA-approved source of manufacture of new products and articles.

(2) Monitoring of the current status of the product and article in relation to shelf life and AD compliance. Each functional test/inspection must be performed in accordance with the standards set forth by § 43.13.

(3) Provisions for the retention of all records that may be necessary as part of the airworthiness documentation required by either 14 CFR part 21, 43, 91, 121, 135, or 145 for approval for return to service (for example, AD compliance).

(4) Provisions for documentation (FAA Form 8130-3, Block 13 or an attachment) that clearly states the process used to determine airworthiness, including each reference to invoices, manufacturer maintenance manuals, or other instructions for continued airworthiness and FAAapproved/acceptable technical data. Attachments should include the form tracking number of the corresponding FAA Form 8130-3.

b. In all cases, FAA Form 8130-3 must be signed by the appropriately authorized representative of an FAA-approved air agency, air carrier, or PAH.

c. European CAAs may recognize an approval for return-to-service FAA Form 8130-3 only from 14 CFR part 145 repair stations or air carriers that also obtained an EASA part 145 approval appropriately rated for the product or article at the time the product or article was approved for return to service. If a dual release is being applied to FAA Form 8130-3 to satisfy a European CAA or EASA, the air agency, U.S. air carrier, or FAA approval/certification number must be entered in Block 21, along with the following statement in Block 13: “Certifies that the work specified in Blocks 12/13 was carried out in accordance with EASA part 145 and, with respect to that work, the component is considered ready for release to service under EASA part 145 Approval Number [insert number: EASA 145-XXX].” In addition, both boxes in Block 19 must be checked.

3-4. Issuance of FAA Form 8130-3 for Used Products and Articles Removed from a U.S.-Certificated Aircraft for Installation on Another U.S.-Certificated Aircraft.

a. FAA Form 8130-3 may be issued for approval for return to service of those products and articles removed from a U.S.-certificated aircraft (under an operating certificate in accordance with part 121 or part 135) for use on another aircraft operated under the same air carrier certificate. The removal and installation of products and articles must be accomplished in accordance with the air carrier’s approved maintenance program or other acceptable methods, techniques, and practices; or FAA-approved/accepted data that is acceptable to the air carrier’s approved maintenance program. The use of FAA Form 8130-3 for this purpose is optional.

b. Those products and articles removed from a U.S.-certificated aircraft other than those referenced in paragraph 3-4a must have an airworthiness determination made in accordance with § 43.13(a) and (b) by an FAA-approved air agency or U.S. air carrier. This also includes compliance with applicable ADs, modification status, and total time/cycles for those products and articles as required by §§ 91.417, 121.380, and 135.439. The use of FAA Form 8130-3 for this purpose is optional, but the FAA recommends its use.

3-5. Block-By-Block Instructions for Completing FAA Form 8130-3 for Approval for Return To Service.

a. Block 1. Approving National Aviation Authority/Country. FAA/United States. (Preprinted.)

b. Block 2. Authorized Release Certificate, FAA Form 8130-3, Airworthiness Approval Tag. (Preprinted.)

c. Block 3. FAA Form Tracking Number. Enter the number established by the numbering system. (Refer to paragraph 3-1j of this order.)

d. Block 4. Organization Name and Address. Enter the full name and physical address (no post office box numbers) of the organization or facility for which the form is being issued, and the facility’s certificate number (for example, certificate No. LI1R 123K or X9MA123H), as appropriate. A logo or other identification of the organization is permitted if it can be contained within the block.

e. Block 5. Work Order/Contract/Invoice Number.

(1) Fill in the work order number, contract number, and/or invoice number related to the shipment list, or maintenance release authorization number, and state the number of pages attached to the form, including dates, if applicable. If the shipment list contains the information required in Blocks 6 through 12, the respective blocks may be left blank if an original or true copy of the list is attached to the form. In this case, the following statement must be entered in Block 13: “This is the certification statement for the products and articles listed on the attached document dated … , containing pages … through … ” In addition, the shipping list must cross-reference the form tracking number located in Block 3. (Refer to figure 2-3 of this order.)

(2) If a work order/contract/invoice number is not available, enter “N/A.”

f. Block 6. Item. When FAA Form 8130-3 is issued, a single item number or multiple item numbers (for example, same item with different serial numbers) may be used for the same part number. Multiple items must be numbered in sequence, although not necessarily beginning with the number one (for example, 0040, 0050, 0062, 0063). If a separate listing is used, enter “List Attached” (refer to paragraph 3-5e of this order for further instructions).

g. Block 7. Description. Enter the name or description of the product or article as referenced in a part catalog or overhaul manual. For PAHs that rebuild products or articles in accordance with § 43.3(j), preference should be given to the term used in the instructions for continued airworthiness or maintenance data (for example, illustrated parts catalog or aircraft maintenance manual).

h. Block 8. Part Number. Enter each part number of the product or article. In case of an aircraft engine or propeller, the model designation may be used. If the article being worked is a

subassembly that does not have a part number of its own, enter the next higher assembly number followed by the word “subassembly.”

i. Block 9. Eligibility. Enter “N/A.”

j. Block 10. Quantity. Enter the quantity of each product or article shipped.

k. Block 11. Serial/Batch Number. If the product or article is required by part 45 to be identified with a serial number, enter it here. Additionally, any other serial number not required by regulation also may be entered. If no serial number is entered in this block, enter “N/A.”

l. Block 12. Status/Work. The following table describes what to enter in a specific situation. Only one term may be entered in Block 12, which should reflect the majority of the work performed by the organization. The use of upper or lower case in this block does not matter.

Enter— For— “Overhauled” A process that ensures the product or article is in complete conformity with the applicable service tolerances specified in the type certificate holder’s or equipment manufacturer’s instructions for continued airworthiness, or in the data approved or accepted by the authority. The product or article will be at least disassembled, cleaned, inspected, repaired as necessary, reassembled, and tested in accordance with the approved or accepted data. “See Block 13” Products or articles rebuilt or altered by authorized PAHs in accordance with § 43.3(j). Refer to paragraph 3-5m(3). “Repaired” Repair of defect(s) using an applicable standard. “Inspected” or “Tested” Examination or measurement in accordance with an applicable standard (for example, visual inspection, functional testing, or bench testing). “Modified” Alteration of a product or article to conform to an applicable standard.

NOTE: The applicable standard must be described in Block 13.

m. Block 13. Remarks. The use of upper or lower case in this block does not matter.

(1) Describe the work identified in Block 12 and associated results necessary for the user or installer to determine the airworthiness of the product or article in relation to the work being certified. This can be done either directly or by reference to supporting documentation. If necessary, a separate sheet may be used and referenced from the main FAA Form 8130-3. Each statement must clearly identify which product or article in Block 6 it relates to.

(2) Below are examples of conditions that could necessitate a statement in this block. These statements may or may not be appropriate depending on the form’s purpose.

(a) Data required by § 43.9, including the reference and revision status. If other documents such as work orders, shop travelers, or FAA Form 337, Major Repair and Alteration (Airframe, Powerplant, Propeller, or Appliance), are used by the certificate holder to comply with §§ 43.9 and 43.11, they must be specifically referenced in this block.

(b) Compliance with ADs or service bulletins.

(c) Repairs carried out.

(d) Modifications carried out.

(e) Replacement articles installed.

(f) Life-limited parts status (for example, total time, total cycles, time since new).

(g) Deviations from the customer work order.

(h) Release statements to satisfy a CAA maintenance requirement.

(i) Information needed to support shipment with shortages or re-assembly after delivery.

NOTE: Examples in paragraph 3-5m(2)(h) show the possibility of dual release against both 14 CFR part 43 and another CAA’s maintenance requirement or the single release by a part 145-approved maintenance facility against a CAA maintenance requirement. However, care should be taken to check the relevant box(es) in Block 19 to validate the release. A dual release requires the approved data to be approved/accepted by both the FAA and appropriate CAA.

(3) When an authorized person completes Blocks 19 through 23 for the purpose of rebuilding or altering a product they hold the approval for in accordance with § 43.3(j), the term “SEE BLOCK 13” will be entered in Block 12, and one of the following statements will be entered in Block 13: “REBUILT TO ORIGINAL PAH’S SPECIFICATIONS” or “ALTERED TO ORIGINAL PAH’S SPECIFICATIONS.”

n. Blocks 14 through 18. Shade, darken, or otherwise mark to preclude inadvertent or unauthorized use.

o. Block 19. Approval for Return to Service. Mark the appropriate box(es) indicating which regulations apply to the completed work. If the box “Other regulations specified in Block 13” is marked, then the regulations of the other CAA(s) must be identified in Block 13. At least the left box must be marked, or both boxes may be marked, as appropriate.

(1) The regulations of the other CAA must be specifically identified in Block 13. The completed work can be accomplished in accordance with the regulations of the FAA, or the regulations of the FAA and another CAA. The data used to complete the work must be clearly stated in Block 13 or attached to the form and the attachment identified in Block 13. If the work has been done in accordance with both the regulations of the FAA and another CAA, both boxes

must be checked. (Refer to paragraph 3-2a(3) of this order for dual release instructions.) Attachments should include the form tracking number of the corresponding FAA Form 8130-3.

(2) The phrase “REBUILT (ALTERED OR INSPECTED) TO ORIGINAL PAH’S SPECIFICATIONS” will be entered in Block 13 when a PAH rebuilds, alters, or inspects their product in accordance with § 43.3(j) or § 43.7(d).

p. Block 20. Authorized Signature. This space will be completed with the signature of the authorized person. Only persons specifically authorized are permitted to sign this block. The approval signature must be applied at the time and place of issuance and manually applied, except as provided in paragraph 3-1k of this order.

q. Block 21. Approval/Certificate No. Enter the PAH, air agency, or air carrier certificate number (for example, OTWR165K).

r. Block 22. Name. Enter the typed or printed name of the authorized representative whose signature appears in Block 20.

s. Block 23. Date (m d y). The date to be entered in Block 23 for approval for return to service will be the date on which the original work was completed (refer to § 43.9). The date must be in the following format: first three letters of the month, two-digit day, and four-digit year, for example, Feb 03 2008. This does not need to be the same as the printing or shipping date, which may occur later. The use or omission of slashes, hyphens, or spaces in the date does not matter.

3-6. Lost FAA Form 8130-3 Issued for an Approval for Return To Service. If a copy of an FAA Form 8130-3 is requested, a file copy of the original form may be provided by an authorized person, if available.

3-7. Reissuance of FAA Form 8130-3 Because of Typographical Errors on the Original. The original issuer may reissue FAA Form 8130-3 if there are typographical errors on the original.

a. The recipient must provide a written statement and a copy of the incorrect FAA Form 8130-3 to the original issuer that indicates the errors.

b. Once these actions are taken, the copy of the original form should be reviewed to determine validity of the errors. If the errors are valid, a corrected form may be issued and the words “THIS FORM 8130-3 REPLACES FORM 8130-3 WITH FORM TRACKING NUMBER [insert number], DATED [enter original issuance date]” must be typed in Block 13. The replacement form must have an original signature and the date the signature was applied. The erroneous form must be marked as such. Both forms should be retained according to the retention period associated with the original form.

Chapter 4. Export Airworthiness Approvals of Aircraft Engines, Propellers, or

Chapter 4. Export Airworthiness Approvals of Aircraft Engines, Propellers, or

Articles

4-1. General Information on Export Airworthiness Approvals.

a. Part 21, subpart L contains the procedural requirements for application for and issuance of export airworthiness approvals for aircraft engines, propellers and articles. An FAA ASI or an authorized designee/delegation may perform the export function to determine whether the products/articles conform to the FAA-approved design data, and to determine whether the importing country or jurisdiction requires any special conditions and that the products are in a condition for safe operation. If the PAH knows that the product/article will be installed on a non-U.S.-registered aircraft, or on an aircraft registered in a country where the CAA requires an export airworthiness approval, then the approval should be accomplished regardless of the aircraft’s location. FAA Form 8130-3 does not constitute approval to install a product or article on a particular aircraft, aircraft engine, or propeller.

b. The country or jurisdiction of import may have a requirement that the FAA certify that the exported product/article conforms to that country’s or jurisdiction’s CAA-approved design approval. This is similar to the requirement placed on a CAA to certify that products/articles exported to the United States meet the FAA-approved type design in accordance with 14 CFR part 21, subpart N, Acceptance of Aircraft Engines, Propellers, and Articles for Import. The check in Block 14 (“Approved design data and are in a condition for safe operation”) indicates that the product/article meets the CAA- and FAA-approved design and is in a condition for safe operation.

(1) It is the applicant’s responsibility to meet the special import requirements of the country or jurisdiction to which the product/article is being shipped. In addition, it is the applicant’s responsibility to obtain sufficient data that verifies the product/article being exported conforms to the importing country’s or jurisdiction’s design approval (if any) and any special import requirements. When an applicant notifies the FAA that a product/article does not meet the requirements of the importing country or jurisdiction, the FAA must then obtain a written statement from the CAA of the importing country or jurisdiction signifying its acceptance. Requests for acceptance of these products/articles to the CAA of the importing country or jurisdiction should be transmitted to and received from authority to authority. The FAA must receive a written statement of acceptance from the CAA of the importing country or jurisdiction before export. All noncompliances to the CAA-approved design must be noted in Block 13, Remarks, of FAA Form 8130-3.

(2) The requirements for a specific country or jurisdiction may be found in one or both of the following: (1) a bilateral agreement or (2) a specific document submitted to the FAA for publication that contains import requirements. The FAA Web site http://www.faa.gov/aircraft/air_cert/international contains a listing of the bilateral agreements as well as a listing of requirements submitted to the FAA by importing countries and jurisdictions. Refer to appendix 2 to AC 21-2, Export Airworthiness Approval Procedures, Special Requirements of Importing Countries, now maintained online at http://www.faa.gov/aircraft/air_cert/international/export_aw_proc/sp_req_import/.

(3) If the country or jurisdiction to which a product or article is exported does not have a bilateral agreement with the United States, or has not stated any special import requirements, FAA Form 8130-3 may still be issued as an export approval. In this case, Block 13 should indicate “Export airworthiness approval. No special import requirements for [enter name of country or jurisdiction] stated at time of issuance.”

(4) If a statement is requested by the country or jurisdiction of import to document that country’s or jurisdiction’s design approval data, and no such corresponding design approval data is available, a statement to that effect must be written in Block 13.

(5) If a written statement of acceptance has been received from the importing CAA regarding noncompliance to its approved design, a copy of this written statement of acceptance must be included with FAA Form 8130-3 to meet § 21.331.

(6) The following instructions are to be followed before issuing an export airworthiness approval:

(a) Review. When a written application is required, part II of FAA Form 8130-1, Application for Export Certificate of Airworthiness (FAA Form 8130-1), must be reviewed to determine its accuracy and the validity of the eligibility of the product or article being submitted for FAA export approval. Designees will maintain records of the inspection and issuance or denial of FAA Form 8130-3. These records must be made available for review and evaluation as requested by FAA personnel. FAA Form 8130-1 may be documented electronically instead of formally populating, printing, signing, and retaining it in the paper format.

(b) Inspection. When the application is determined acceptable, the product or article must be inspected to the extent necessary to ensure that it conforms to the FAA-approved design data, is in a condition for safe operation, is properly identified, and meets any design or special requirements of the importing country or jurisdiction. The FAA managing office must make the determination of whether an FAA Form 8100-1 has to be completed for each FAA Form 8130-3 issued for export based on the PAH’s quality system’s health and/or the designee’s previous history, experience, or performance, or if the information can be stored and retrieved in another format (for example, electronic database). If required by the FAA managing office responsible for the designee/designee organization, each designee authorized to issue approvals for export will document the inspection results on FAA Form 8100-1 for periodic review and evaluation by the FAA.

1) When documenting the “nomenclature of item inspected” in Block 9 of the FAA Form 8100-1, also include the form tracking number (Block 3) and item number (Block 6) from the FAA Form 8130-3 completed for the product export airworthiness approval.

2) When applicable, FAA Form 8100-1 must include the results of the inspection, date of issuance, country of destination, description of product, and manufacturer’s invoice or shipping document number.

(c) In the case where a product or article is presented for inspection for the issuance of FAA Form 8130-3, and the product or article is sealed in a package that does not afford a visible inspection, the authorized person must request to see the objective evidence to

determine that the appropriate inspections were conducted and approved before the issuance of FAA Form 8130-3.

c. Splitting of previously exported bulk shipments by a PAH or a PAH’s associate facility is not within the control or jurisdiction of the FAA. Therefore, once products or articles are exported, those items would be under the control or jurisdiction of the receiving authority.

d. FAA Form 8130-3 may be issued for products or articles outside the United States if the FAA finds no undue burden in administering the applicable requirements in accordance with § 21.325(c).

e. FAA Form 8130-3 must be completed as described in paragraph 4-5 of this order. Samples of an FAA Form 8130-3 for export airworthiness approval are found in figures 4-1, 4-2, and 4-3 of this order.

f. FAA Form 8130-3 must be correlated with the shipment. Additional copies of the original FAA Form 8130-3 may be provided upon request.

g. If FAA Form 8130-3 is issued as an export airworthiness approval of a new product or article, the issuer should retain a copy of FAA Form 8130-3 for no less than 5 years.

h. The copies of FAA Form 8100-1 and FAA Form 8130-3 may be retained in their original paper format or in a secure database, provided the database contains all of the information required on FAA Form 8130-3. An acceptable means of compliance is provided in AC 21-35 (or AC 21-43 upon issuance) or AC 120-78 (when applicable), and is available for FAA review upon request. Duplicates of FAA Form 8130-3, including signatures retained in a database, do not need to be graphic images of the original documents.

i. Unique identification is required to enable or provide product or article traceability. The preferred method is a unique form tracking number in Block 3. However, if traceability is provided through other information on the form combined with a number in Block 3, this is also acceptable.

j. The signature of the person authorized to issue FAA Form 8130-3 may be applied electronically to Block 15. With exception of paragraphs 4-6 and 4-7b, at the time the signature is authorized to be placed on FAA Form 8130-3, the person whose signature appears on the form must have direct access to the product or article to verify that it conforms to FAA-approved design data and is in a condition for safe operation, or that any special conditions required by the importing country or jurisdiction are met.

k. An FAA Form 8130-3 issued subsequent to the original finding of airworthiness is considered a recurrent airworthiness approval, for example, a PMA or TSO authorization article that left the PAH’s quality/inspection system and is being presented for export.

Figure 4-1. Sample FAA Form 8130-3 for Export Airworthiness Approval

4-2. New Products and Articles. Export airworthiness approvals for aircraft engines, propellers, and articles are issued in accordance with § 21.331.

4-3. Used Products. Used products or articles are not eligible for an export airworthiness approval unless the importing country’s or jurisdiction’s CAA specifically agrees to accept such used products in accordance with § 21.331(d). Requests for acceptance of these used products to the importing country’s CAA should be transmitted to and received from authority to authority.

4-4. PMA Articles. The following applies when exporting PMA articles using FAA Form 8130-3:

a. Various bilateral agreements with countries have specific additional requirements for the acceptance of U.S. PMA articles into those countries. The applicable bilateral agreement should be reviewed for the specific provisions associated with PMA articles.

b. When a particular bilateral agreement requires such a specific provision for PMA articles, statements must be entered in Block 13, if applicable.

c. The determination of a PMA article’s criticality, as required to be entered in Block 13 when exported to European countries, can only be determined by the actual design approval holder (that is, the FAA-PMA holder).

d. The text of all bilateral agreements can be found at http://www.faa.gov/aircraft/air_cert/international/bilateral_agreements.

Figure 4-2. Sample FAA Form 8130-3 for Export Airworthiness Approval for a

New Subcomponent for a TSO Authorization Article

4-5. Block-By-Block Instructions for Completing FAA Form 8130-3 for Export Airworthiness Approvals.

a. Block 1. Approving National Aviation Authority/Country. FAA/United States. (Preprinted.)

b. Block 2. Authorized Release Certificate, FAA Form 8130-3, Airworthiness Approval Tag. (Preprinted.)

c. Block 3. FAA Form Tracking Number. Enter the number established by the numbering system. (Refer to paragraph 4-1i of this order.)

d. Block 4. Organization Name and Address.

(1) Enter the full name and physical address (no post office box numbers) of the organization or facility for which the form is being issued, and the facility’s certificate number (for example, certificate No. LI1R 123K or X9MA123H), as appropriate. A logo or other identification of the organization is permitted if it can be contained within the block.

Figure 4-2: picture of page 43Figure 4-2 · page 43
Picture of the page from the copy saved here

(2) When a supplier has direct shipment authorization from a PAH, the following information must be entered:

(a) PAH name and address.

(b) Supplier name and address.

(c) PAH certificate or project number (for example, certificate No. PC 700 or PQ0123CE). If the supplier is unsure what number to use, consult the PAH for assistance.

(3) If a supplier produces a product or article as a replacement product or article, the supplier must either have direct shipment authorization or hold a production approval (PMA/TSO authorization) for each replacement product or article shipped. If the supplier holds its own production approval, and the products or articles were manufactured and are being shipped under that approval, the information required in paragraph 4-5d(1) must be listed.

e. Block 5. Work Order/Contract/Invoice Number.

(1) Fill in the work order number, contract number, and/or invoice number related to the shipment list, or maintenance release authorization number, and state the number of pages attached to the form, including dates, if applicable. If the shipment list contains the information required in Blocks 6 through 12, the respective blocks may be left blank if an original or true copy of the list is attached to the form. In this case, the following statement must be entered in Block 13: “This is the certification statement for the products or articles listed on the attached document dated … , containing pages … through … ” (Refer to figure 2-3 of this order.)

(2) In addition, the shipment list must cross-reference the form tracking number located in Block 3. The shipment list may contain more than one item, but it is the responsibility of the shipper to determine whether the CAA of the importing country or jurisdiction will accept bulk shipments under a single FAA Form 8130-3. If the CAA does not permit bulk shipments under a single form, Blocks 6 through 12 of each form must be filled in for each product or article shipped.

(3) If work order/contract/invoice number is not available, enter “N/A.”

f. Block 6. Item. When FAA Form 8130-3 is issued, a single item number or multiple item numbers (for example, same item with different serial numbers) may be used for the same part number. Multiple items must be numbered in sequence, although not necessarily beginning with the number one (for example, 0040, 0050, 0062, 0063). If a separate listing is used, enter “List Attached” (refer to paragraph 4-5e of this order for further instructions).

g. Block 7. Description. Enter the name or description of the product or article as shown on the design data.

h. Block 8. Part Number. Enter each part number of the product or article.

i. Block 9. Eligibility. Enter “N/A.”

j. Block 10. Quantity. Enter the quantity of each product or article shipped.

k. Block 11. Serial/Batch Number. If the product or article is required by part 45 to be identified with a serial number, enter it here. Additionally, any other serial number not required by regulation also may be entered. If no serial number is entered in this block, enter “N/A.”

l. Block 12. Status/Work. The following table describes what to enter in a specific situation. Only one term may be entered in Block 12, which should reflect the majority of the work performed. The use of upper or lower case in this block does not matter.

Enter— For— “New” The production of a new product or article in conformity with the approved design data. “Overhauled” Products or articles overhauled in accordance with § 43.2. Approved design data refers to instructions for continued airworthiness that may be supplied by the holder of the design approval for the product or article in accordance with § 21.50. For overhauled products or articles, FAA-approved/accepted data may have been developed to accomplish the maintenance function to comply with § 21.50. “Prototype” The production of a new product or article in conformity with non-approved design data to support type certification programs. “Inspected” “Repaired” or “Modified”

Other situations, as appropriate.

NOTE: The term “Inspected” includes testing of products and articles.

m. Block 13. Remarks. The use of upper or lower case in this block does not matter.

(1) State any information in this block, either directly or by reference to supporting documentation, necessary for the user or installer to determine the airworthiness of the product or article. Bilateral agreements may require certain statements to be added to the export form; those statements should be entered in this block. If necessary, a separate sheet may be used and referenced from the main FAA Form 8130-3. Each statement must be clearly identified as to the product or article in Block 6 to which it relates. If there is no statement, state “none.”

(2) Below are examples of conditions that could necessitate a statement in this block. These statements may or may not be appropriate depending on the form’s purpose.

(a) “Prototype products (articles) pending certification under FAA project number [enter number] and are not eligible for installation on in-service, type-certificated aircraft. Upon approval of the design data, the product(s)/article(s) listed above are considered new, conform with approved design data, and are in a condition for safe operation without further showing.” Block 14 will be marked as “Non-approved design data specified in Block 13.”

(b) When a new FAA Form 8130-3 is issued to correct errors, the following statement must be entered: “This FAA Form 8130-3 corrects the error(s) in block(s) [enter block numbers corrected] of the FAA Form 8130-3 [enter original form tracking number] dated [enter original issuance date] and does not cover conformity/condition/release to service.”

(c) Attachments when used. Attachments should include the form tracking number of the corresponding FAA Form 8130-3.

(d) For TSO articles, enter the applicable TSO number.

(e) Information on life-limited parts (for example, total time, total cycles, time since new).

(f) Shelf-life data.

(g) Shortages or outstanding work, for example, missing parts on an assembly or reassembly after shipment.

(h) Any data not appropriate in other blocks.

(3) When used by authorized suppliers with properly documented direct shipment authorization from the PAH, the words “DIRECT SHIPMENT AUTHORIZATION” must be entered in Block 13, and the information from paragraph 4-5d(2) of this order must be entered in Block 4. (Refer to figure 4-3 of this order.)

(4) When used for export approval for used products and articles returned to service based on the requirements of 14 CFR part 43, the words “USED (PRODUCT/ARTICLE), SHIPPED PER CAA STATEMENT OF ACCEPTANCE FOR USED (PRODUCT/ARTICLE)” must be entered. Refer to paragraph 4-3, which stipulates that the importing authority must

submit a written statement accepting used products and articles. Refer to applicable bilateral agreements.

(5) If a written statement of acceptance has been received from the importing CAA regarding a noncompliance to its approved design, the noncompliance to the CAA-approved design must be entered in Block 13.

(6) When used for an export for a new subcomponent of a PMA/TSO authorization article higher assembly, complete FAA Form 8130-3 with the subcomponent information, and enter a statement in Block 13 indicating that the part or article is a subcomponent of a PMA or TSO authorization (for example, “This part is a subcomponent of a PMA/TSO authorization”). (Refer to figure 4-2 of this order.)

(7) If a statement is requested by the country to which the product or article is being exported that documents that country’s design approval data, and no such corresponding design approval data is available, a statement to that effect must be written in Block 13.

(8) If the PAH holds the type design data for replacement articles produced under an STC, “Produced by the STC design approval holder” must be entered in Block 13.

(9) If the issuer has found that the product or article meets the special import requirements of the importing country or jurisdiction, Block 13 should indicate: “Export airworthiness approval— this article meets the special requirements of (enter country).” If the importing country or jurisdiction does not have special import requirements applicable to the product or article, then the statement does not need to be included. The finding of compliance with a particular country’s or jurisdiction’s special import requirements should not be interpreted to preclude export or re-export to another country, but the exporter/re-exporter should confirm compliance with the special import requirements of the destination country or jurisdiction.

(10) For exported aircraft engines or propellers, include total time and, if applicable, time since overhauled.

Figure 4-3. Sample FAA Form 8130-3 for a Direct Shipment Authorization for Export

Figure 4-3: picture of page 48Figure 4-3 · page 48
Picture of the page from the copy saved here

n. Block 14. Airworthiness Approval. Place a check in the “Approved design data and are in a condition for safe operation” box if the products and articles were manufactured using FAA-approved design data and found to be in a condition for safe operation. Checking this box and signing Block 15 means that the products and articles listed on the form meet the FAA-approved design data, are in a condition for safe operation, and, in the case of export, meet the importing country’s or jurisdiction’s design approval and meet the special requirements of that importing country or jurisdiction. Also, if “OVERHAULED” is identified in Block 13, check this box.

o. Block 15. Authorized Signature. This space will be completed with the signature of the authorized person. Only an FAA ASI, authorized designee, or person approved to sign under an authorized delegation are authorized to sign this block. An alternative to a handwritten signature (for example, a computer-generated signature) is permitted only when authorized by the FAA. The approval signature must be applied at the time and place of issuance and manually applied, except as provided in paragraph 4-1j of this order.

p. Block 16. Approval/Authorization No. Enter the approval/authorization number of the authorized representative/organization identified in Block 15. If signed by an FAA inspector, the authorization number is the applicable office identifier.

q. Block 17. Name. Enter the typed or printed name of the authorized representative/organization whose signature appears in Block 15.

r. Block 18. Date (m d y). The date must be in the following format: first three letters of the month, two-digit day, and four-digit year, for example, Feb 03 2008. This does not need to be the same as the printing or shipping date, which may occur later. The use or omission of slashes, hyphens, or spaces in the date does not matter.

s. Blocks 19 through 23. Shade, darken, or otherwise mark to preclude inadvertent or unauthorized use.

4-6. Lost FAA Form 8130-3 Issued for Export Airworthiness Approvals. If a copy of an FAA Form 8130-3 is requested, a file copy of the original form may be provided by an authorized person, if available.

4-7. Reissuance of FAA Form 8130-3 for Export Airworthiness Approvals.

a. Reissuance by PAH for Returned Products and Articles.

(1) The new products and articles returned to a PAH may be eligible for a new FAA Form 8130-3 if—

(a) The new products and articles were produced under the PAH’s production approval.

(b) The PAH maintains a procedure to accept products and articles back into their quality system.

(c) Tests and inspections are performed in accordance with procedures contained in the PAH’s quality system to determine that the returned product or article still meets the original type design it was produced under and still is in a condition for safe operation.

(2) If the conditions in paragraphs 4-7a(1)(a) through (c) are met, a new FAA Form 8130-3 in accordance with chapter 4 of this order may be issued.

(3) If the original FAA Form 8130-3 is returned with the products and articles, the issuer should retain that form on file with (or have reference to) the new FAA Form 8130-3.

b. Reissuance Because of Typographical Errors on the Original.

(1) If the recipient finds an error(s) on an FAA Form 8130-3, the recipient must identify the error(s) in writing to the originator. The originator may issue a new FAA Form 8130-3 if the originator can verify and correct the error(s).

(2) The request for a new FAA Form 8130-3 may be honored without reverification of the product or article condition. The new FAA Form 8130-3 is not a statement of current condition and should refer to the previous FAA Form 8130-3 in Block 13 by the following statement: “This FAA Form 8130-3 corrects the error(s) in Block(s) [enter block number(s) corrected] of the FAA Form 8130-3 [enter original form tracking number] dated [enter original issuance date] and does not cover conformity/condition/release to service.” The erroneous form must be marked as such. Both forms should be retained according to the retention period associated with the original form.

Chapter 5. Electronic Use of the Authorized Release Certificate,

FAA Form 8130-3, Airworthiness Approval Tag

5-1. Purpose of This Chapter. This chapter provides guidance on the acceptance and use of the electronic exchange of FAA Form 8130-3, for those entities that elect to comply with the required standards and guidance that governs the use of such electronic documentation for aircraft products and articles.

5-2. Background on Electronic FAA Form 8130-3.

a. The Government Paperwork Elimination Act (GPEA), Public Law 105-277, Title XVII, and the Electronic Signatures in Global and National Commerce Act (E-Sign), Public Law 106-229, encourage use of electronic signatures.

b. Before the enactment of E-Sign on June 30, 2000, the regulations on signatures acknowledging satisfaction of manufacturing and maintenance requirements did not reflect current advances in information storage and retrieval technology. These earlier rules were developed when use of electronic media for the storage and retrieval of data was neither available to, nor contemplated by, the aviation industry or the FAA.

c. As the complexity of aircraft design, manufacturing, and maintenance processes increased, the number of records and documents generated and required to be retained by aircraft manufacturers, owners, operators, and repair facilities expanded dramatically. Electronic information storage and retrieval systems have enhanced significantly the aviation industry’s ability not only to meet FAA record-retention requirements, but also to manufacture, operate, and maintain today’s highly complex aircraft and aircraft systems in a demanding operational environment.

d. The Office of Management and Budget (OMB), Executive Office of the President, has issued OMB Circular A-130, Management of Federal Information Resources. OMB Circular A-130 directs the FAA and other Government agencies to recognize the limitations on electronic recordkeeping systems due to restrictions on the use of electronic signatures. The FAA recognizes this limitation and will now permit the use of electronic signatures on the electronic FAA Form 8130-3. Manufacturers, owners, operators, and maintenance personnel may now use complete electronic recordkeeping systems because the requirement to authenticate documents with non-electronic signatures has been eliminated. Such systems may be used to generate FAA Form 8130-3 that can be properly authenticated with an electronic signature.

e. As a result of the above (GPEA, enactment of E-Sign, and OMB Circular A-130), the FAA and industry formed the Electronic Documentation Project Team (EDPT) to develop an industry specification to enable the electronic exchange of FAA Form 8130-3 for aircraft products and articles. The requirements contained in this chapter for the use of the electronic version of FAA Form 8130-3 and the specifications contained in Air Transport Association (ATA) Specification 2000 (Spec 2000), chapter 16, Electronic Product and Part Regulatory Documentation, is the direct result of the efforts put forth by that team. Not only the

requirements of FAA Form 8130-3 were developed, but corresponding forms used by other authorities (that is, EASA, Transport Canada Civil Aviation (TCCA), etc.) were considered.

f. The use and acceptance of electronic FAA Form 8130-3 (and other corresponding EASA and TCCA forms) offers several distinct advantages over the current paper format:

(1) Through the use of standard data semantics and structures contained in ATA Spec 2000, chapter 16, a higher degree of data reliability and consistency will be achieved.

(2) Through adoption of common, widely available digital security technologies, it is considerably more difficult to forge or alter data without being detected, and the data can more easily be traced directly to the source.

(3) Identifying a document signer (signatory) will be easier through the elimination of traceability difficulties associated with illegible handwritten entries and the deterioration of paper documents.

(4) The frequency of lost, damaged, and unreadable documents can be significantly reduced.

(5) The automated processes for generating, transmitting, and processing data will significantly reduce costly human errors.

(6) The cost and difficulty to store, retrieve, and analyze information can be substantially reduced.

5-3. General Procedures for the Use of Electronic FAA Form 8130-3.

a. The use of the electronic transfer FAA Form 8130-3 procedures is strictly voluntary when issuing FAA Form 8130-3 for its intended purpose as specified in chapters 2, 3, and 4 of this order. If authorized persons elect to implement the following procedures, it must be understood that both the issuer and recipient of the electronic form must comply with the procedures in this chapter. If for whatever reason the data recipient is unable to accept the electronic form, the issuance of the form must be in paper format in accordance with the appropriate chapter of this order.

b. Those authorized persons who elect to issue the electronic FAA Form 8130-3 for products and articles must comply with the guidelines in this chapter, specific block-by-block instructions contained in chapters 2, 3, and 4 as appropriate, and the standardized set of data formats, data requirements (tables 16-2-1 and 16-2-2), business guidelines, and reference documents in the ATA Spec 2000, chapter 16. ATA Spec 2000, chapter 16 is available by contacting ATA at 202-626-4000, or via e-mail at [email protected].

c. ATA Spec 2000, chapter 16 provides the specific extensible markup language (XML) as the standard format for the exchange of electronic FAA Form 8130-3 for products and articles. Chapter 16 also provides the minimum requirements for digital security when issuing and receiving the electronic FAA Form 8130-3 data and the set of tables describing the data elements used for the various uses for the form, including their Text Element Identifiers (TEIs).

d. The following is a brief description of the content of ATA Spec 2000, chapter 16:

Continue reading ↓ 120 of 161 passages shown