Radar Vectors
FAA Order Cancelled Issued Dec 21, 2012 AJT-2 197 pages Copy saved Nov 18, 2026

Order JO 7900.5C Surface Weather Observing

This document is cancelled. Cancelled by JO 7900.5D. Check the official source before relying on it.

Official source ↗ Open PDF

U.S. DEPARTMENT OF TRANSPORTATION ORDER FEDERAL AVIATION ADMINISTRATION JO 7900.5C

Air Traffic Organization Policy

Effective Date:

12/21/2012

SUBJ: Surface Weather Observing

The Federal Aviation Administration (FAA) surface weather observer program is a component of the

National Airspace System (NAS). It combines with other elements of the NAS to ensure the overall safety ofair transportation services. The FAA is committed to providing the resources necessary to ensure the vibrancy of this critical aviation service. This order provides the practices and procedures for weather observation services that support the important role it plays in the mission ofthe FAA.

The practices and procedures set forth in this order apply to all FAA personnel, FAA-contract personnel, and non-Federal Observer personnel who provide aviation weather observation services. Weather observer personnel are required to apply the provision of this order as it pertains to their observational

responsibilities. Observers are expected to exercise experienced judgment when encountering situations not covered by this order.

C Vice President, Terminal Services

Distribution: Initiated By: AJT-2

Table of Contents

Chapter 1. Introduction … 1 1.1. Purpose of This Order. … 1 1.2. Audience. … 1 1.3. Where to Find This Order. … 1 1.4. Cancellation … 1 1.5. Explanation Of Changes … 1 1.6. Abbreviations and Acronyms. … 2 1.7. Relationship to FMH-1 and Other Documents … 2 1.8. Applicability of Procedures and Practices … 2 1.9. User Responsibilities … 3 1.10. Distribution. … 3 1.11. Changing the Order. … 3 1.12. Maintaining the Order. … 3

Chapter 2. Guidelines … 4 2.1. Introduction … 4 2.2. Types of Stations … 4 2.3. General Types of Observations … 5 2.4. Augmentation Requirements … 5 2.5. Backup Requirements … 6 2.6. Long-Line Backup Requirements … 10 2.7. Certification of Personnel and Currency Requirements … 11 2.8. Types and Content of METAR/SPECI Observations. … 12

Chapter 3. General Procedures … 13 3.1. Introduction. … 13 3.2. Definitions … 13 3.3. Aviation Weather Observing Locations. … 14 3.4. General Observing Practices … 15 3.5. Dissemination … 16 3.6. Dissemination Requirements … 16 3.7. Corrections to Transmitted Data … 17 3.8. Delayed Reports … 17 3.9. Rounding Off Numbers. … 17 3.10. Record Keeping and Forms … 17 3.11. Evaluating Weather Sensor Accuracy … 17 3.12. Criteria for SPECI Observations. … 18 3.13. Content of METAR/SPECI Observations. … 19

Chapter 4. General Procedures at Automated Weather Stations … 28 4.1. Purpose. … 28 4.2. Types of Automated Stations … 28 4.3. Certification … 30 4.4. General Procedures … 30 4.5. General Equipment Procedures. … 30 4.6. Procedures at Non-Federal Observation Sites. See Appendix B … 31 4.7. Procedures at Non-Federal AWOS Sites … 31

ii

4.8. Procedures for Handling Aircraft Mishaps at Automated Sites. … 31 4.9. General Requirements for Record Keeping. … 31

Chapter 5. Augmentation Requirements at Automated Weather Stations … 32 5.1. Introduction. … 32 5.2. Validity of Data … 32 5.3. Sign On/Sign Off the Automated Weather Observing Systems. … 32 5.4. Order for Reporting Weather and Obstructions to Visibility. … 33 5.5. Augmentation Observing Procedures. … 34 5.6. Reporting Procedures … 34 5.7. Examples of Augmented Observations. … 36

Chapter 6. Backup Requirements at Automated Weather Stations … 37 6.1. Introduction. … 37 6.2. Summary of Backup Requirements. … 37 6.3. Validity of Data … 38 6.4. Equipment Requirements. … 38 6.5. Procedures for Providing Backup Information. … 39 6.6. Coding of Missing Data … 39 6.7. Procedures for Wind Speed and Wind Direction. … 39 6.8. Procedures for Visibility … 41 6.9. Procedures for Present Weather and Obscurations … 42 6.10. Procedures for Sky Condition. … 43 6.11. Procedures for Temperature and Dew Point. … 46 6.12. Procedures for Altimeter Setting … 47 6.13. Procedures for Documentation. … 47 6.14. Procedures for Communications. … 47 6.15. Disposition of MFIM-10C. … 47 6.16. Examples of Backup Observations. … 47 6.17. Malfunctions/Outages. … 49

Chapter 7. Wind … 50 7.1. Introduction. … 50 7.2. Definitions … 50 7.3. Observing, Determining, and Reporting Procedures. … 50 7.4. Wind Direction. … 50 7.5. Estimating Wind Direction … 51 7.6. Variable Wind Direction. … 51 7.7. Wind Shifts … 51 7.8. Wind Speed. … 52 7.9. Estimating Wind Speed. … 52 7.10. Wind Character (Gusts) … 52 7.11. Peak Wind Speed. … 52 7.12. Calm Wind. … 52 7.13. Conversion of True and Magnetic Winds. : … 52 7.14. Instrumental Evaluation Procedures. … 53

Chapter 8. Visibility … 54 8.1. Introduction … 54

iii

8.2. Definitions … 54 8.3. Visibility Standards. … 54 8.4. Unit of Measure. … 54 8.5. Observing Aids for Visibility … 55 8.6. Tower Visibility Aids … 55 8.7. Selection of Visibility Markers. … 55 8.8. Observation Sites. … 55 8.9. Dark Adaptation. … 55 8.10. Evaluating Visibility … 55 8.11. Evaluating Prevailing Visibility … 56 8.12. Evaluating Sector Visibility. … 56 8.13. Evaluating Variable Visibility … 56 8.14. Reporting Visibility Values … 56 8.15. Control Tower Observations and Actions at Collocated Sites. … 56 8.16. Additional Tower Personnel Action for Tower Visibility. … 56 8.17. Contract Observer Action at Stations with Control Tower. … 57

Chapter 9. Runway Visual Range (RVR) … 58 9.1. Introduction. … 58 9.2. Definitions … 58 9.3. Sensor and Method. … 58 9.4. Observing Positions. … 61 9.5. Day-Night Observations for Transmissometers. … 61 9.6. Automated Long-Line RVR Observations. … 61 9.7. Multiple RVRs … 61 9.8. Units of Measure. … 61 9.9. RVR Based on Transmissometer. … 61 9.10. Automated RVR. … 61 9.11. Limits of RVR. … 61 9.12. Variation in RVR. … 62 9.13. Determining and Reporting RVR (NA LAWRS). … 62 9.14. RVR Procedures (Apply to RVRs Using Transmissometer Technology Only). … 62 9.15. Ten-minute RVR Values (Apply to RVRs Using Transmissometer Technology Only). … 62 9.16. Manually Determined One-minute RVR Values (Apply to RVRs Using Transmissometer. Technology Only). … 63 9.17. Emergency Reporting of Runway Visibility and RVR (Apply to RVRs Using Transmissometer Technology Only) (NA LAWRS) … 63 9.18. Disposing of RVR Recorder Charts (Apply to RVRs Using Transmissometer Technology Only) … 63 9.19. Operation of Equipment. … 63

Chapter 10. Weather Phenomena … 64 10.1. Introduction. … 64 10.2. Precipitation … 64 10.3. Obscurations. … 65 10.4. Other Phenomena … 66 10.5. Qualifiers … 67 10.6. Order for Reporting Multiple Types of Weather and Obscurations. … 67

iv

10.7. Rules for Phenomena Not Occurring at the Point of Observation … 68 10.8. Reporting and Documenting Precipitation. : … 69 10.9. Beginning and/or Ending Precipitation (NA LAWRS). … 69 10.10. Determining and Reporting the Type of Precipitation. … 69 10.11. Determining the Character of Precipitation … 69 10.12. Precipitation Intensity. … 70 10.13. Intensity of Snow, Snow Pellets, Snow Grains, Drizzle, and Freezing Drizzle. … 71 10.14. Reporting Freezing Precipitation. … 71 10.15. Beginning and/or Ending of Freezing Precipitation. … 71 10.16. Intensity of Freezing Precipitation … 71 10.17. Reporting Ice Pellets. A SPECI observation must be taken whenever ice pellets begin, end, or change intensity … 72 10.18. Beginning and/or Ending of Ice Pellets (NA LAWRS) … 72 10.19. Intensity of Ice Pellets … 72 10.20. Reporting Precipitation Amounts (NA LAWRS). … 72 10.21. Priority of Gauges (NA LAWRS). I … 72 10.22. Stick Measurement of Liquid Precipitation (NA LAWRS). … 72 10.23. Determining Water Equivalent of Solid Precipitation by Stick Measurement (NA LAWRS).

(Applies only to the standard 8-inch, nonrecording rain gauge). … 73 10.24. Determination of 6-hour Accumulation of Precipitation (NA LAWRS). … 73 10.25. Depth Measurement of Solid Forms (NA LAWRS). … 73 10.26. Snowfall Within Specified Periods (NA LAWRS). … 74 10.27. Tornado, Waterspout, or Funnel Cloud. … 74 10.28. Reporting Thunderstorms … 75 10.29. Beginning and/or Ending of a Thunderstorm. … 76 10.30. Reporting Hail. … 76 10.31. Beginning and/or Ending of Hail. If SPECI is because of hail, then begin/end time must be recorded in the remarks … 76 10.32. Reporting Lightning … 76 10.33. Reporting Squalls. … 76 10.34. General. … 77 10.35. Observing Obscurations. … 77 10.36. Reporting Obscurations … 77 10.37. Special Procedures for Volcanic Ash … 77 10.38. Operationally Significant Remarks for Obscurations. … 77

Chapter 11. Sky Condition … 78 11.1. Introduction. … 78 11.2. Sky Condition Evaluation. … 78 11.3. Cloud Forms and Obscuring Phenomena. … 78 11.4. Ceiling. … 78 11.5. Celestial Dome … 78 11.6. Cloud. … 78 11.7. Cloud Movement. … 78 11.8. Field Elevation. … 78 11.9. Horizon. … 78 11.10. Interconnected Cloud Layers … 79

v

11.11. Layer … 79 11.12. Layer Amount. … 79 11.13. Layer Height. … 79 11.14. Multiple Layers … 79 11.15. Obscuring Phenomena. … 79 11.16. Sky Cover. … 79 11.17. Sky Cover Classifications … 79 11.18. Summation Amount. … 80 11.19. Summation Principle. … 80 11.20. Surface … 80 11.21. Total Amount. … 80 11.22. Variable Ceiling … 80 11.23. Variable Sky Condition. … 80 11.24. Observing Sites. … 80 11.25. Layer Amounts. … 81 11.26. Summation Layer Amount. … 82 11.27. Layer Heights. … 82 11.28. Evaluation of Multiple Layers. … 83 11.29. Amount of Obscuration … 83 11.30. Determining Amount of Sky Cover. … 83 11.31. Evaluation of Sky Cover Amounts. … 83 11.32. Sky Cover Classification … 83 11.33. Variable Sky Cover … 84 11.34. Non-Uniform Sky Cover. … 84 11.35. Estimated Ceiling Heights … 84 11.36. Variable Ceiling Height … 84 11.37. Significant Clouds. … 85

Chapter 12. Temperature and Dew Point … 86 12.1. Introduction. … 86 12.2. Temperature … 86 12.3. Psychrometer … 86 12.4. Hygrothermometer. … 86 12.5. General. … 86 12.6. Maximum and Minimum Temperature. … 86 12.7. Hygrothermometer (NA LAWRS) … 87

Chapter 13. Pressure … 88 13.1. Introduction. … 88 13.2. Altimeter Setting (ALTSG) … 88 13.3. Atmospheric Pressure. … 88 13.4. Barometric Pressure … 88 13.5. Field Elevation, Ha … 88 13.6. Pressure Altitude, PA (NA CWO) … 88 13.7. Pressure Change (NA LAWRS) … 88 13.8. Pressure Falling Rapidly (NA LAWRS). … 88 13.9. Pressure Rising Rapidly (NA LAWRS). … 89 13.10. Pressure Tendency (NA LAWRS) … 89

vi

13.11. Sea Level Pressure … 89 13.12. Standard Atmosphere. … 89 13.13. Station Elevation, Hp. … 89 13.14. Station Pressure (NA CWO) … 89 13.15. Density Altitude, DA. … 89 13.16. Barometric Elevation, HZ. … 89 13.17. Posted Pressure Correction. … 89 13.18. General (NA LAWRS) … 90 13.19. Rounding Pressure Values. … 90 13.20. Barometers Used to Measure Station Pressure (NA LAWRS/NA CWO) … 90 13.21. Precision Aneroid (NA LAWRS/NA CWO) … 90 13.22. Altimeter Setting (NA LAWRS/NA CWO) … 91 13.23. Digital Altimeter Setting Indicator (DASI) (NA LAWRS) … 91 13.24. Sea Level Pressure … 91 13.25. Determining Altimeter Setting (NA LAWRS) … 91 13.26. Method of Determining Altimeter Setting (NA LAWRS) … 92 13.27. Altimeter Setting Indicator (NA LAWRS) … 92 13.28. Pressure Reduction Computer and Altimeter Setting (NA LAWRS) … 92 13.29. Altimeter Setting Reduction Constant (NA LAWRS) … 92 13.30. Altimeter Setting Table (NA LAWRS) … 92 13.31. Pressure Altitude (PA) (NA LAWRS/NA CWO) … 93 13.32. Local Pressure Altitude Tables (NA LAWRS/NA CWO) … 93 13.33.

Altimeter Setting and Pressure Reduction Computer (NA LAWRS/NA CWO) … 93 13.34. Altimeter Setting and Pressure Altitude Table (NA LAWRS/NA CWO) … 93 13.35. Station Pressure and Pressure Reduction Computer (NA LAWRS/NA CWO). … 94 13.36. Station Pressure and Pressure Altitude Table (NA LAWRS/NA CWO) … 94 13.37. Pressure Related Remarks (NA LAWRS) … 97 13.38. Pressure Falling Rapidly (NA LAWRS). … 97 13.39. Pressure Rising Rapidly (NA LAWRS). … 97 13.40. Pressure Tendency (NA LAWRS) … 97 13.41. Frequency of Pressure Tendency Remark (NA LAWRS). … 97 13.42. Determining Pressure Change (NA LAWRS/NA CWO) … 97 13.43. Determining Pressure Tendency Characteristic (NA LAWRS) … 98 13.44. The provisions of this section are applicable only at LAWRS … 98 13.45. The only pressure related measurement required at LAWRS is the altimeter setting … 98

Chapter 14. Coding and Dissemination … 99 14.1. Introduction. … 99 14.2. Definitions … 99 14.3. Aviation Weather Reports Code. … 99 14.4. Format and Content of the METAR/SPECI Report. … 100 14.5. Coding Missing Data in METAR and SPECI Reports. … 100 14.6. Coding the Body of the METAR or SPECI Report. … 100 14.7. Type of Report (METAR or SPECI) … 100 14.8. Station Identifier (CCCC). … 100 14.9. Date and Time of Report (YYGGggZ). … 101 14.10. Report Modifier (AUTO or COR) … 101

vii

14.11. Wind Group ((dddff(f)Gfmfm(fm)KT)_(dndndnVdxdxdx)). … 101 14.12. Visibility Group (VVVVVSM) … 102 14.13. Runway Visual Range Group (RDRDR/VRVRVRVRFT) or (RDRDR/VnVnVnVnVVxVxVxVxFT) (NA LAWRS) … 102 14.14. Present Weather Group (w’w’) … 103 14.15. Sky Condition Group (NsNsNshshshs or VVhshshs or CLR or SKC) … 106 14.16. Temperature/Dew Point Group (T’T’/T’dT’d) … 108 14.17. Altimeter (APHPHPHPH). … 108 14.18. Remarks (RMK) … 108 14.19. Automated, Manual, and Plain Language Remarks. … 109 14.20. Volcanic Eruptions. … 109 14.21. Funnel Cloud (TORNADIC ACTIVITY_B/E(hh)mm_LOC/DIR_(MOV)) … 109 14.22. Type of Automated Station (AO1 or AO2) … 110 14.23. Peak Wind (PK WIND_ddff(f)/(hh)mm) (NA LAWRS) … 110 14.24. Wind Shift (WSHFT_(hh)mm). … 110 14.25. Tower or Surface Visibility (TWR_VIS_vvvvv or SFC_VIS_vvvvv). … 110 14.26. Variable Prevailing Visibility (VIS_vnvnvnvnvnVvxvxvxvxvx) … 110 14.27. Sector Visibility (VIS_[DIR]_vvvvv). … 110 14.28. Visibility at Second Location((VIS_vvvvv_[LOC]) (NA LAWRS). … 111 14.29. Lightning Frequency (Frequency_LTG(Type)_[LOC]) … 111 14.30.

Beginning and Ending of Precipitation (w’w’B(hh)mmE(hh)mm) (NA LAWRS). … 112 14.31. Beginning and Ending of Thunderstorms (TSB(hh)mmE(hh)mm). … 112 14.32. Thunderstorm Location (TS_LOC_(MOV_DIR)) … 112 14.33. Hailstone Size (GR_[size]) … 113 14.34. Virga (VIRGA_(DIR)) … 113 14.35. Variable Ceiling Height (CIG_hnhnhnVhxhxhx) … 113 14.36. Obscuration (w’w’_[NsNsNs]hshshs) … 113 14.37. Variable Sky Condition (NsNsNs(hshshs)_V_NsNsNs). … 113 14.38. Significant Cloud Type [PLAIN LANGUAGE] … 114 14.39. Ceiling Height at Second Location (CIG_hhh_[LOC]) (NA LAWRS). … 114 14.40. Pressure Rising or Falling Rapidly (PRESRR or PRESFR) (NA LAWRS) … 115 14.41. Seal-Level Pressure (SLPppp) (NA LAWRS) … 115 14.42. Aircraft Mishap (ACFT_MSHP) … 115 14.43. No SPECI Reports Taken (NOSPECI). … 115 14.44. Snow Increasing Rapidly (SNINCR_(inches-hour/inches on ground)) (NA LAWRS) … 115 14.45. Other Significant Information. … 115 14.46. Additive and Automated Maintenance Data. … 115 14.47. Hourly Precipitation Amount (Prrrr) (NA LAWRS) … 116 14.48.

1, 3, and 6 Hourly Ice Accretion Amounts (I1nnn, I3nnn, I6nnn) (NA LAWRS). … 116 14.49. 3- and 6- Hour Precipitation Amount (6RRRR) (NA LAWRS) … 117 14.50. 24-Hour Precipitation Amount (7R24 R24 R24 R24) (NA LAWRS) … 117 14.51. Snow Depth on Ground (4/sss) (NA LAWRS). … 117 14.52. Water Equivalent of Snow on Ground (933RRR) (NA LAWRS). … 118 14.53. Hourly Temperature and Dew Point (TsnT’T’T’snT’dT’dT’d) (NA LAWRS) … 118 14.54. 6-Hourly Maximum Temperature (1snTxTxTx) (NA LAWRS) … 118 14.55. 6-Hourly Minimum Temperature (2snTnTnTn) (NA LAWRS) … 118 14.56. 24-Hour Maximum and Minimum Temperature (4snTxTxTxsnTnTnTn) (NA LAWRS) … 119

viii

14.57. 3-Hourly Pressure Tendency (5appp) (NA LAWRS) … 119 14.58. Sensor Status Indicators. … 120 14.59. Maintenance Indicator … 121 14.60. Transmission Times … 121

Chapter 15. Entries on Observational Forms … 122 15.1. Introduction. … 122 15.2. Entries on Meteorological Form 1M-10C (MF1M-10C). … 122 15.3. Writing Instrument. … 122 15.4. Parenthetical Data … 122 15.5. Missing Data … 122 15.6. Late Observations … 122 15.7. Corrections. … 122 15.8. Heading on Form MF1M-10C at LAWRS … 122 15.9. Heading on Form MF1M-10C at Other Stations (NA LAWRS) … 123 15.10. Entries on Form MF1M-10C by Columns … 123 15.11. Additional Instructions for Part-Time Stations. … 130 15.12. Additive Data Groups (NA LAWRS). … 130 15.13. Tailoring MF1M-10C, Synoptic Data, and Summary of the Day (NA LAWRS). … 130 15.14. Notice of Corrections to Weather Records. … 131

Chapter 16. Operation of Equipment … 134 16.1. Introduction. … 134 16.2. Ice Accretion Indicators … 134 16.3. General. … 134 16.4. General … 134 16.5. Aneroid Barometer or Altimeter Setting Indicator (NA CWO) … 134 16.6. Excessive Drift. … 135 16.7. Inspection Comparisons (NA CWO). … 135 16.8. Electronic Pressure Transducers … 135 16.9. Temperature and Dewpoint Indicators … 135

Appendix A. Abbreviations and Acronyms … 136

Appendix B. Non-Federal Observing (NF-OBS) Program … 142

Appendix C. Limited Aviation Weather Reporting Station (LAWRS) Requirements … 143

C.1 Purpose … 143 C.2 General … 143 C.3 Requirements … 143 C.4 Requirements for LAWRS without an Automated System … 143 C.5 Procedures for LAWRS Using Automated Systems with SPECI Capability … 143 C.6 Procedures for LAWRS with Automated Systems without SPECI Capability … 144 C.7 Observing, Determining, and Reporting Procedures at LAWRS … 145 C.8 Altimeter Setting From Altimeter Setting Indicators (Only LAWRS) … 145 C.9 Determining the Reliability of Altimeter Setting Indicators (Only LAWRS) … 145 C.10 Daily Comparison with an Adjacent Station (Only LAWRS) … 146 C.11 Altimeter Setting From a DASI … 147 C.12 Electronic Pressure Transducers or Other DASIs … 147

ix

Appendix D. Service Standards … 152

D.1 Description … 152 D.2 Determining Level of Service … 153 D.3 Procedures … 153

Appendix E. METAR User Aids … 155

E.1 U.S. METAR/SPECI Code Format with Remarks … 157 E.2 Notations for Reporting Weather Phenomena … 159 E.3 Key to Decode METAR/SPECI Observations … 160 E.4 Weather Phenomena Matrix … 160 E.5 Fahrenheit to Celsius … 163 E.6 Tenth of Degrees Celsius to Whole Degrees Fahrenheit … 165

Appendix F. Transmission (WS FORM B-11) … 166

Appendix G. General Requirements for Measuring Snow Depth … 167

G.1 Purpose … 167 G.2 Description … 167 G.3 FAA Order 7900.5 Guidelines … 167 G.4 List of CWO Sites that will be required to perform snow depth measurements … 168

Appendix H. Glossary … 171

Appendix I. Index … 182

Appendix J. Automated Weather System Operation and Broadcast … 184

Appendix K. Explanation of Changes … 185

List of Figures

Figure A-1: WS Form B-14 … 132 Figure A-2: Example of Entries on MF1M-10C, presents an example of a filled-in MF1M-10C form 133

List of Tables

Table 2-1: Guide to Contents of Automated and METAR and SPECI Observations … 7 Table 3-1: Content of METAR … 19 Table 3-2: Remarks Section of Observation … 21 Table 4-1: Operator Procedures for Providing Augmentation and Backup Information … 30 Table 5-1: Summary of FAA Augmentation Requirements … 33 Table 5-2: Examples of Augmented Observations … 36 Table 6-1: Summary of Long-line Backup Requirements … 37 Table 6-2: Backup Reporting of Wind or Altimeter Setting … 39 Table 6-3: Estimating Wind Speed … 40 Table 6-4: Backup Reporting of Surface Visibility … 41 Table 6-5: Backup Reporting of Weather Phenomena … 42 Table 6-6: Backup and Augmentation Weather and Obscurations … 42 Table 6-7: Backup Reporting of Sky Condition … 43

x

Table 6-8. Priority for Reporting Cloud Layers … 44 Table 6-9: Criteria for Variable Ceiling … 45 Table 6-10: Increments of Reportable Values of Sky Cover Height … 45 Table 6-11: Reportable Contractions for Sky Cover Amount … 46 Table 6-12: Backup Reporting of Temperature and Dew Point … 46 Table 6-13: Automated System without SPECI Capability Backup Observation Examples … 48 Table 6-14: Automated System with SPECI Capability Backup Observation Examples … 49 Table 7-1: Estimating Wind Speed … 52 Table 8-1: Reportable Visibility Values … 55 Table 9-1: RVR Transmittance Conversion Table for Tasker 400 and Equivalent Systems with 250-Foot

Baseline - Contrast Threshold 5.5 Percent … 59 Table 9-2: Tasker 500 RVR Transmittance Conversion Table for 250-Foot Baseline - Contrast

Threshold 5.0 Percent … 59 Table 10-1: Present Weather … 68 Table 10-2: Estimating Intensity of Rain … 70 Table 10-3: Estimating Intensity of Ice Pellets … 70 Table 10-4: Intensity of Rain or Ice Pellets Based on Rate of Fall … 70 Table 10-5: Intensity of Snow or Drizzle Based on Visibility … 70 Table 10-6: Precipitation Intensity Symbols … 71 Table 10-7: Units of Measure for Precipitation … 72 Table 10-8: Type and Frequency of Lightning … 75 Table 11-1: Reporting Contractions for Sky Cover … 81 Table 11-2: Priority for Reporting Layers … 81 Table 11-3: Examples: Summation of Sky Cover … 82 Table 11-4: Increments of Reportable Values for Layer or Ceiling Heights … 83 Table 11-5: Criteria for Variable Ceiling … 84 Table 13-1: Units of Measure of Pressure Parameters … 90 Table 13-2: Barometers Used … 90 Table 13-3: Portion of an Altimeter Setting Table … 92 Table 13-4: Pressure Altitude … 94 Table 14-1: Content of METAR/SPECI … 99 Table 14-2: METAR or SPECI Code Format … 100 Table 14-3: Reporting Visibility Values … 102 Table 14-4: Present Weather … 106 Table 14-5: Reportable Values for Sky Cover Amount … 107 Table 14-6: Increments of Reportable Values of Sky Cover Height … 107 Table 14-7: Type and Frequency of Lightning … 111 Table 14-8: Units of Measure for Precipitation … 116 Table 14-9: Characteristics of Barometer Tendency … 120 Table C-1: LAWRS Requirements for Body of METAR … 147 Table C-2: LAWRS Requirements for Remarks Section … 148 Table C-3: LAWRS Requirements for SPECIs … 150 Table C-4: Backup Reporting of Visibility … 151 Table D-1: Service Standard Levels … 154 Table F-1: WS Form B-11 … 166

xi

Chapter 1. Introduction

1.1. Purpose of This Order. This order prescribes aviation surface weather observing procedures and practices. This order includes practices and procedures for both manual and automated observation locations. Also included are practices and procedures for augmentation of automated observations and backup information in the event of system failure, erroneous or non-representative data. These procedures and practices are intended to provide a framework for identifying meteorological phenomena of importance to aviation and reporting their occurrence.

Chapter 1. Introduction › 1.5. Explanation Of Changes.

1.2. Audience. This order applies to all FAA and FAA-contract personnel, Limited Aviation Weather Reporting Stations (LAWRS) personnel, Non-Federal Observation (NF-OBS) Program personnel, as well as United States Coast Guard (USCG) personnel as a component of the Department of Homeland Security and National Weather Service (NWS) personnel engaged in taking and reporting aviation surface observations.

1.3. Where to Find This Order. This order is available on the FAA Web site at http://faa.gov/air_traffic/publications and http://employees.faa.gov/tools_resources/orders_notices/.

1.4. Cancellation. This order cancels FAA Order 7900.5B, Surface Weather Observing - METAR, effective December 1, 2005.

1.5. Explanation Of Changes. This revision is primarily editorial and does not introduce any hazard into the National Airspace System. General changes to the order are documented below, which provides additional information to assist the user in understanding and locating the new changes included in this order. (See Appendix K)

General:

References for equipment system names (i.e., ASOS, AWOS) were deleted and replaced throughout 7900.5C with: Automated Systems With SPECI Capability, and Automated Systems Without SPECI Capability.

Removed outdated procedures and equipment.

Designated Stations: The published order required many procedures to be followed at ‘designated stations.’ Now the order identifies stations and their applicable procedures.

References previously scattered throughout various chapters have been consolidated into dedicated chapters.

LAWRS requirements previously scattered throughout 7900.5, have been consolidated into Appendix C which makes the document more usable.

Chapters and Paragraphs were deleted and renumbered.

Chapters were renamed to coincide with the purpose and content of the chapters.

Figures and Tables have been updated to identify their new locations in 7900.5C.

1

Chapter 1. Introduction › 1.8. Applicability of Procedures and Practices

1.6. Abbreviations and Acronyms. Appendix A. Abbreviations and Acronyms, contains abbreviations and acronyms used in this order.

1.7. Relationship to FMH-1 and Other Documents

a. Federal Meteorological Handbook No. 1, Surface Weather Observations and Reports (FMH-1). FMH-1 prescribes surface weather observing standards applicable to all Federal agencies engaged in taking and reporting surface aviation observations. FMH-1 also prescribes the standard reporting and coding procedures used in the surface aviation observation. Order 7900.5C prescribes the procedures and practices to be followed by FAA, FAA-contract and NF-OBS personnel for observing, reporting, and coding of surface observations that meet the Federal standards. A brief description of the NF-OBS program (FAA owned ASOS/AWSS only) is provided in Appendix B. Non-Federal Observing (NF-OBS) Program. This order complements, but does not change the standards contained in FMH-1.

b. Automated Weather Observing Systems Handbooks. Handbooks are produced by automated systems manufacturers. However, all systems must be operated in accordance with practices and procedures contained in this order. A partial listing of the applicable handbooks necessary to operate the various automated weather observing systems includes:

(1) Federal Aviation Administration, Operator Instructions, Automated Weather Observing System (AWOS), August 1, 1994, U.S. Department of Transportation, Washington, DC.

(2) NWS ASOS Ready Reference Guide (RSM1005-00038 Rev. H)

1.8. Applicability of Procedures and Practices

a. Applicability. The procedures and practices in this order apply to all facilities that have the capability to comply with the stated procedure or practice. Some procedures and practices vary at LAWRS sites. LAWRS requirements are contained in Appendix C, LAWRS Requirements. At sites ranked as Service Level C, the basic weather observing requirements are the same as a LAWRS observation. LAWRS observers are not required to back up the observation if measuring or observing equipment is not available.

b. Conflicting Information. In case of conflicting information, the procedures and practices in this order take precedence. However, any applicable FAA air traffic orders take precedence over any procedures or practices in this order that are in conflict. Such conflicts should be brought to the attention of the originator of this order.

c. Terminology. Throughout this order, the following terminology applies:

(1) “Must” indicates a procedure or practice that is mandatory at all applicable facilities.

(2) "Should" indicates a procedure or practice that is recommended at all applicable facilities.

(3) "May" indicates a procedure or practice that is optional.

(4) "Will" indicates futurity; it is not a requirement to be applied to current practices.

2

d. Unforeseen Requirements. No set of procedures and practices can cover all possibilities in weather observing. The observer must use good judgment, adhering as closely as possible to this order, to describe phenomena not adequately covered by specific instructions. Suggestions for possible changes in procedures and practices to cover such situations may be made through appropriate channels.

Chapter 1. Introduction › 1.12. Maintaining the Order.

1.9. User Responsibilities. Employee participation in directive writing and upkeep activities is encouraged. Any user who finds a subject matter conflict, an error, obsolete information, or who would like to make recommendations or suggestions should notify Terminal Safety and Operations Support, in writing. FAA Form 1320-19, Directive Feedback Information, is available for this purpose. If clarification or correction is urgently needed, you may call Terminal Safety and Operations Support for guidance, but you should also use the FAA Form 1320-19 as a follow-up to verbal conversation.

1.10. Distribution. This order is distributed to select offices in Washington Headquarters; Air Traffic Organization – Terminal Service Areas; Office of Operations Planning; NAS Weather Office; Flight Standards Service; the Mike Monroney Aeronautical Center; the William J. Hughes Technical Center; the USCG Elizabeth City Facility; the Department of Defense (DOD); all terminal air traffic field facilities; all Alaska flight service stations (FSS); FAA-contract weather; and the National Weather Service (NWS).

1.11. Changing the Order. Changes, additions, deletions, and corrections will be issued as necessary. These changes will be issued by the Director, Terminal Safety and Operations Support.

1.12. Maintaining the Order. Each facility must maintain a copy of the order, complete with changes and supplements for reference purposes. When inserting changes to the order, enter the number, effective date, initials, and date entered on the inside cover of this order.

3

Chapter 2. Guidelines › 2.2. Types of Stations.

Chapter 2. Guidelines

2.1. Introduction. This chapter describes the types of aviation surface weather observing facilities for which the FAA may have responsibility or oversight. This chapter also describes the various types of surface weather reports, including the Aviation Routine Weather Report (METAR) and Aviation Selected Special Weather Report (SPECI), and FAA guidelines regarding the content of each of these types. Also presented are general guidelines regarding augmentation and backup of automated observations. Lastly, this chapter presents FAA guidelines on the certification of observers.

2.2. Types of Stations. The generic types of stations that take aviation weather observations are defined as follows:

a. Automated Station. A facility equipped with a "Federally Procured" automated surface weather observing system that prepares the observation without a certified observer on duty. The various types of automated stations are described in Chapter 4. Observations generated by automated stations will always be identified by the inclusion of the word AUTO in the transmitted report.

b. Augmented Station. A facility with a "Federally Procured" automated surface weather observing system that prepares the METAR/SPECI with a certified observer on duty capable of adding operationally significant weather information to the observation. The observer is completely responsible for the observation even though the automated weather observing system generates the report. At facilities where augmentation is not available full time, the facility is classed as automated during the non-augmented periods.

c. Manual Station. A facility, other than LAWRS, where certified weather observers are responsible for observing, evaluating, and preparing the METAR/SPECI.

d. Towered Station. Any facility with an airport traffic control tower operated by the FAA or operated under an FAA contract.

e. Nontowered Station. Any facility without an FAA or FAA contract airport traffic control tower.

f. Limited Aviation Weather Reporting Station (LAWRS). A facility where observations are taken, prepared, and transmitted by certified FAA control tower personnel, FAA-contract control tower personnel, or Flight Service Station (Alaska only) personnel on a limited basis to support aviation requirements. At these facilities, various degrees of automated sensors and/or other automated equipment may be available.

g. Flight Service Station (FSS). Throughout this order, the term flight service station (FSS) refers to any flight service station or automated flight service station (FSS) in Alaska, which has been directed by FAA headquarters or service area office to provide the observing, augmentation, or backup service indicated.

h. Non-Federal Observing (NF-OBS) Station. A program in which non-Federal observers such as non-Federal control tower (NFCT) controllers, airline personnel, or fixed base operator (FBO) personnel may enter into an agreement with the appropriate FAA Service Area to provide backup and augmentation of the automated system with SPECI capability. NF-OBS observers are certified by

4

Chapter 2. Guidelines › Augmentation Requirements.

NWS. At these facilities, various degrees of automated sensors and/or other automated equipment may be available. However, when on duty, the NF-OBS observer must provide backup and augmentation in accordance with their NF-OBS agreement. Program establishment is contained in Appendix B and responsibilities are described in Chapter 4. General Procedures at Automated Weather Stations.

2.3. General Types of Observations . There are three general types of surface observations:

a. Automated Observation. Any observation which has been prepared and transmitted by an automated observing system without human intervention.

b. Augmented Observation. Any automated observation which has been evaluated by a human observer to which additional weather information has been manually added that is beyond the capabilities of the automated weather observing system and/or is deemed operationally significant. The guidelines concerning augmentation are presented in Paragraph 2.4 Augmentation Requirements. Backup is a method of providing an observation, part of an observation, documentation, or communication of an observation at selected sites when the primary method is unavailable or nonrepresentative. The guidelines concerning backup information are presented in Paragraph 2.5 Backup Requirements.

NOTE- Backing up a failed automated system is not considered a manual observation.

c. Manual Observation. Any observation for which the human observer observes, evaluates, prepares, records, and transmits the observation without the use of an automated observing system. The guidelines for manual observations are presented in Chapter 3. General Procedures.

2.4. Augmentation Requirements. Certified observers are responsible for the completeness and accuracy of the weather observation. Automated weather observing systems are, by design, viewing a smaller area than a human observer. Therefore, the observer is responsible for providing additional information that covers a larger area when operationally significant. Augmentation of automated observations must be provided in accordance with the guidelines presented in the following subsections and as specified for the station’s service level standard (Appendix D. Service Standards). Separate guidelines are presented for the two general types of automated weather observing systems: automated systems with SPECI capability and automated systems without SPECI capability. Procedures and practices to be followed to accomplish the required augmentation are presented in Chapter 4. General Procedures at Automated Weather Stations, and Chapter 5. Augmentation Requirements at Automated Weather Stations.

a. Facilities with an Automated System with SPECI Capability.

(1) ATCT with a Surface-Based Observer. At facilities with an ATCT, and an automated system with SPECI capability, and with a surface-based observer on duty, the surface-based observer must provide augmentation of the automated observation. This augmentation must include, but not be limited to the requirements contained in Service Standards for that level of airport (see Appendix D. Service Standards). At these facilities, the ATCT must routinely provide tower visibility when applicable.

(2) All other facilities with an Automated System with SPECI Capability. At facilities with an ATCT, and an automated system with SPECI capability, but without a surface-based observer on

5

Chapter 2. Guidelines › 2.5. Backup Requirements

duty, the tower observer must provide augmentation of the automated observation. At facilities with surface based observers, augmentation will be the responsibility of the co-located FSS (Alaska only) or other weather observers. This augmentation must include, but not be limited to:

(a) Thunderstorm.

(b) Tornadic activity (including tornado, waterspout, and funnel cloud).

(c) Hail.

(d) Virga.

(e) Volcanic ash.

(f) Any weather elements considered operationally significant by the observer.

b. Facilities with an Automated System without SPECI Capability. At these facilities, the observation is the responsibility of the surface-based observer, if one exists. At towered sites without a surface-based observer, the observation is the responsibility of the LAWRS observer.

REFERENCE­ FAAO JO 7210.3 para 2-9-2d, Receipt and Dissemination of Weather Observations

2.5. Backup Requirements

a. Situations Requiring Backup. Certified observers are responsible for the completeness and accuracy of the weather observation. If the complete automated observation is unavailable due to sensor/system malfunction, communications failure, and/or non-representative data, backup information must be provided in accordance with the guidelines in the following subsections. Backup refers to the observer providing the same reporting capability as that provided by the automated weather sensor, consistent with service level standards specified in Appendix D Service Standards. Backup information is required for long-line dissemination for terminal forecast (TAF) production and for local, ground-toair dissemination to legally sustain local operations at the airport. The "failure" modes mentioned above are defined as follows:

(1) Sensor/system Malfunction. One or more sensors or the entire observing system is (are) not reporting data (for any reason). Provide manual backup and make appropriate maintenance notifications.

(2) Communications Failure. The automated weather observing system and/or long-line communications are malfunctioning, thereby preventing the entry and/or transmission of the observation over long-line networks. When it is apparent that observations are not being transmitted, relay the observations to the tie-in FSS and notify the appropriate office for outage notification.

(3) Non-representative Data. The sensor is reporting data, but the data are incorrect or the sky condition, visibility, and/or present weather sensor(s) is/are accurately reporting conditions in the vicinity of the sensor, but those conditions are not representative of prevailing conditions for the operating areas of the airport and are considered operationally significant. When this occurs, provide manual backup. Outage notification is not required.

6

b. Level of Support. The information specified in these guidelines is the minimum required for each of the situations discussed in the following subsections. The FAA may specify additional information beyond this minimum. The observer is encouraged to add any other appropriate remarks. Procedures and practices to provide the required backup information are presented in Chapter 6. Backup Requirements at Automated Weather Stations.

c. Communications. Automated weather observing system failure may or may not include loss of long-line communications, local communications, or both. The level of backup information to be provided depends on the status of such communications and whether the information is required for long-line or local, ground-to-air dissemination.

Table 2-1: Guide to Contents of Automated and METAR and SPECI Observations

Element of METAR/SPECI Report(s)

Type of Station:

Automated

System without

SPECI

Automated System with SPECI

Capability Manual

Stand-Alone Augmented

Type of Observation: M M S1 M S M S

Type of Report X X X X X X X

Station Identifier X X X X X X X

Date/Time X X X X X X X

Report Modifier (AUTO or COR) X X X X2 X2 X2 X2

Wind Direction Speed, Character X X X X X X X

Visibility X X X X X X X

Runway Visual

Range A/B A/B A/B3 A/B3

Present Weather4 X X X X X X

Sky Condition

< 12,000 feet X X X X X X X

> 12,000 feet A A X X

Temperature X X X X X X X

Dew Point X X X X X X X

Altimeter Setting X X X X X X X

Remarks:

Group 1 ­ Automated, Manual, and Plain Language

Volcanic X X X X

7

Element of METAR/SPECI Report(s)

Type of Station:

Automated

System without

SPECI

Automated System with SPECI

Capability Manual

Stand-Alone Augmented

Eruptions

Tornadic Activity X X X X

Type of Automated Station (AO1,

AO2)

X X X X X

Peak Wind X X X

Wind Shift X X X X X X

Tower or Surface

Visibility X A/B/C A/B/C A/B/C A/B/C A/B/C A/B/C

Variable Prevailing

Visibility

X X X X X X X

Sector Visibility A A X X

Visibility at Second Location X5 X5 X5 X5

Lightning X X X X X X X

Time of Beginning/Ending

of Precipitation

X X X6 X X6

Time of Beginning/Ending of Thunderstorms

X X X X X X X

Thunderstorm

Location X X X X

Hailstone Size X X X X

Virga X X X X

Variable Ceiling

Height X X X X X

Obscurations4 X X X X

Variable Sky

Condition A A X X

Significant Cloud

Types A A X X

Ceiling Height at Second Location X5 X5 X5 X5

8

Element of METAR/SPECI Report(s)

Type of Station:

Automated

System without

SPECI

Automated System with SPECI

Capability Manual

Stand-Alone Augmented

Pressure Rising/Falling

Rapidly

X X X X

Sea-level

Pressure X X X

Aircraft Mishap X X X X

No SPECI Reports Taken X6

Snow Increasing

Rapidly A/B A/B X

Other Significant

Information X X X X

Remarks: Group 2 – Additive and

Automated Maintenance

Data Hourly Precipitation

Amount

X X X

Ice Accretion X X X X

3-6 Hour Precipitation

Amount

X X X

24- Hour Precipitation X X X X

Depth of Snow

on Ground X7 X

Water Equivalent

of Snow on

Ground

X7 X

Hourly Temperature and

Dew Point

X X X

6- Hourly Maximum Temperature

X X X X

6- Hourly Minimum Temperature

X X X X

9

Chapter 2. Guidelines › 2.6. Long-Line Backup Requirements.

Element of METAR/SPECI Report(s)

Type of Station:

Automated

System without

SPECI

Automated System with SPECI

Capability Manual

Stand-Alone Augmented

24- Hour Max/Min Temperature

X X X X

3- Hourly Pressure Tendency

X X X

Sensor Status

Indicators X X X X

Maintenance

Indicator X X X X

AO1 - Automated station does not have precipitation discrimination capability AO2 - Automated station has precipitation discrimination capability AUTO - Appears in weather report of automated system when observer is not logged on M - METAR S - SPECI X - Indicates elements included at all stations A - Indicates elements that are at service level A (where so equipped) B - Indicates elements that are at service level B (where so equipped) C - Indicates elements that are at service level C (where so equipped) 1 All hourly reports are METAR, all others are SPECIs except automated stations without SPECI capability, which are all METAR. 2 COR only 3 Where so equipped. 4 Automated stations report only a limited set of present weather and obstruction to vision elements. 5 At stations equipped with the meteorological discontinuity sensors. 6 Report if precipitation caused the SPECI 7 See Appendix G for applicability

d. Equipment for Backup Observations. Weather observing equipment should be maintained to allow certified observers to perform backup responsibilities in the event of an automated sensor failure. Air traffic managers must coordinate with the Service Area Office, local Technical Operations System Management Office, and the appropriate NWS regional office before initiating action to decommission weather observing equipment.

2.6. Long-Line Backup Requirements. Details on the procedures to provide backup are in Chapter 6. Backup Requirements at Automated Weather Stations. This paragraph specifies the type of minimum backup for various types of facilities.

a. LAWRS ATCTs. At LAWRS ATCTs, certified air traffic control specialists (ATCS) must provide the backup information for long-line transmission that is listed in this section. The required information must be entered into the automated systems with SPECI capability via the operator interface device. At locations with automated systems without SPECI capability, the required information must be phoned to the tie-in Flight Service Station. The following information must be provided at a minimum:

10

Chapter 2. Guidelines › 2.7. Certification of Personnel and Currency Requirements.

(1) Wind.

(2) Visibility to 10 miles.

(3) Present weather and obstructions to vision (see Table 6-6 for required elements).

(4) Sky condition to 12,000 feet.

(5) Temperature/Dew Point.

(6) Altimeter Setting.

(7) Required remarks and operationally significant remarks as deemed appropriate.

NOTE- Precipitation of unknown form may be reported only if the automated sensor is operational and is reporting precipitation of unknown form. However, if the observer can determine the type of precipitation, it should be reported using the allowable elements listed in Table 6-6.

b. Non-LAWRS ATCTs with a Surface-Based Observer. At non-LAWRS towers with a surface-based observer, the surface-based observer must provide, at a minimum, the back-up information for long-line transmission according to the requirements contained in the Service Standards for the service level of the airport. Backup must also include required remarks and operationally significant remarks as deemed appropriate by the observer. At these facilities, ATCT personnel must routinely provide ATCT visibility information to the surface-based observer as required.

c. Nontowered Facilities with a Surface-Based Observer. At all nontowered facilities, the surface-based observer must provide the backup information required by the Service Standards for the service level of the airport. At all facilities with an operator interface device, the required information must be entered into the automated weather observing system via the operator interface device. Backup must also include required remarks and operationally significant remarks as deemed appropriate by the observer.

2.7. Certification of Personnel and Currency Requirements. Before assuming full responsibility for taking any type of surface observation or any part thereof, each person must be certified. The NWS is responsible for certifying all civilian weather observers in one or more of the following observer types. Definitions of these types are presented in Paragraph 3.2 Definitions. Currency requirements are in FAA Order JO 3120.4, Air Traffic Technical Training.

a. NWS and FAA observers.

b. LAWRS observer.

c. Tower visibility observer is certified by the FAA through eLMS.

11

Chapter 2. Guidelines › 2.8. Types and Content of METAR/SPECI Observations.

2.8. Types and Content of METAR/SPECI Observations. The METAR is the primary code format used in the United States to satisfy requirements for reporting surface meteorological data. The METAR may be prepared by automated weather observing systems (with or without augmentation) or by certified weather observers. These data are primarily reported in an alphanumeric coded format for aviation users.

a. A complete METAR contains the type of report, station identifier, date/time of observation, and whether the report is automated (AUTO) or corrected (COR). Weather phenomena in the METAR include wind, visibility, runway visual range (RVR) (where connected), present weather, sky condition, temperature, dew point, and altimeter setting (collectively referred to as "the body of the report"). In addition, significant information elaborating on data reported in the body of the report or coded and plain language data not included in the body of the report may be appended to the report in a section referred to as "remarks." The content varies according to the type of weather station and the automated weather observing system used (see Table 14-1). Some elements of the remarks section are not required at FAA facilities.

b. The METAR is a scheduled observation between 45 and 59 minutes past the hour. However, at automated stations without SPECI capability, METARs are generated every 20 minutes starting at H+00. A SPECI is an unscheduled observation taken when there is a significant change in the observation since the previous METAR observation was taken or if an aircraft mishap has occurred. If an aircraft mishap occurs close to a scheduled METAR, then it would be transmitted as a METAR. SPECI criteria are applicable only to stations that have the capability of evaluating the event. If it is time for a METAR to be issued and SPECI observation criteria are met, the observation will remain designated as a METAR. The criteria for taking SPECI observations are given in Chapter 3. General Procedures.

c. Table 2-1 summarizes the weather elements that are available at automated observing systems with precipitation discrimination capability (AO2) and those without precipitation discrimination capability (AO1). The precipitation discrimination capability indicator, AO1 or AO2, is included in the remarks section of the applicable METAR or SPECI report. This table also shows the additional elements that are available when an observer is present to add information that is beyond the capabilities of the automated observing system (augmentation). This table does not indicate elements that are required for backup or augmentation. These elements are also found in Appendix D. Service Standards.

12

Chapter 3. General Procedures › 3.2. Definitions.

Chapter 3. General Procedures

3.1. Introduction. This chapter prescribes procedures and practices applicable to all facilities and to all types of observations. These general procedures also apply to observations taken to fulfill requirements for augmentation or minimum operational requirements during backup. This chapter also describes the various types of surface observations and prescribes the criteria for taking SPECI observations. Chapters 7 through 16 prescribe procedures and practices to be followed by all personnel engaged in observing and reporting surface-based meteorological conditions. In addition to prescribing standard procedures and practices, these chapters also prescribe differences in procedures and practices applicable to LAWRS observers.

3.2. Definitions.

a. Actual Time Of Observation. The actual time of observation is the time the last element of the observation is observed or evaluated. The actual time of a SPECI must be the time the criteria for the SPECI were met or noted.

b. Aircraft Mishap. Aircraft mishap is an inclusive term to denote the occurrence of an aircraft accident or incident.

c. Aviation Routine Weather Report (METAR). A METAR is a measurement or evaluation of meteorological elements that describe the state of the atmosphere at the surface location(s) where the observation is taken. METAR is a scheduled observation. The METAR is the primary observation code used in the United States to satisfy requirements for reporting surface meteorological data. It contains a report of wind, visibility, RVR (where connected), weather, sky condition, temperature, dew point, and altimeter setting (collectively referred to as "the body of the report"). In addition, coded plain language information that elaborates on the data in the body of the report may be appended to the METAR or SPECI. This significant information is referred to as "remarks." At Manual Observations and augmented stations, the METAR may be abridged to include one or more of the above elements. The contents of METAR observations are given in Table 3-1. METAR observations that also meet the criteria for a SPECI observation are called METAR observations.

d. Aviation Selected Special Weather Report (SPECI). A SPECI is a weather observation that is reported at other than a scheduled time. SPECI must be taken when any of the criteria for a special observation is observed or detected. A SPECI observation is an unscheduled observation taken when any of the criteria given in Paragraph 3.12 Criteria for SPECI Observations have been observed. A SPECI observation must contain the elements in a METAR, plus additional coded or plain language information that elaborates on the data in the body of the report. The SPECI criteria are applicable only to stations that have the capability of evaluating the event. All SPECI must be taken as soon as possible after relevant criteria are observed.

e. Basic Weather Watch. During a Basic Weather Watch, the observer may be required to perform other duties as their observing workload permits. Because of this and other restrictions (station location, structural design, etc.) that may limit the observer’s capability to continuously view and evaluate weather conditions, observers performing a Basic Weather Watch cannot be expected to detect and report all weather changes as they occur. In addition to taking and disseminating required observations, facilities performing a Basic Weather Watch must recheck weather conditions to

13

Chapter 3. General Procedures › 3.3. Aviation Weather Observing Locations.

determine if a new observation (SPECI) is required when advised by any reliable source (for example, tower controller) that existing conditions differ from those reported in the last disseminated observation.

f. Continuous Weather Watch. At facilities performing a Continuous Weather Watch, the observer must monitor weather conditions on a continuous basis. In addition to METAR observations, observers must take and disseminate observations as conditions meeting criteria for SPECI observations occur.

g. Coordinated Universal Time (UTC). UTC is the time in the zero degree meridian time zone, also commonly known as Zulu (Z) time.

h. Local Standard Time (LST). LST is a time based on the geographic location of the facility in one of the legally established time zones of the globe.

i. Observer. The generic term "observer" applies to a number of different types of personnel with various responsibilities for providing weather information. These various types are:

(1) Weather Observer. A person who is certified by the NWS to provide a designated range of weather observation elements. These include NWS, NWS-contract, FAA, and FAA-contract personnel.

(a) LAWRS Observer. An NWS-certified ATCS with weather observation

responsibilities for surface aviation weather elements.

(b) Tower Visibility Observer. An ATCS certified by the Meteorological Coordinator

and Training Consultant to observe and report airport visibility from the control tower.

(2) NF-OBS Observer. A non-Federal observer working under the guidelines of the NF­ OBS program, providing backup and augmentation of the automated system with SPECI capability.

j. Standard Time of Observation. The standard time of observation is the hour to which a METAR observation applies.

k. Weather Watch. Observers must monitor weather conditions via a weather watch. Two types of weather watch are possible: a Basic Weather Watch and a Continuous Weather Watch. Except where specifically indicated throughout this order, all FAA, FAA-contract, and NF-OBS observers including LAWRS must monitor weather conditions via a Basic Weather Watch as described below.

3.3. Aviation Weather Observing Locations. Surface weather observation locations must make routine reports at fixed intervals (METAR reports). Where the capability exists, the routine reports must be supplemented by non-routine reports (SPECI). The observing location is defined as the point or points at which the various elements are observed. In cases where all the measurements are taken at the same point, an observation will be regarded as having a single location. In cases where the various sensors are located to obtain acceptable exposure, the observation location will be regarded as varying with the individual elements in an observation. Normally, multiple observing points are confined to an area within about 2 miles of the station. Weather reports from manual stations may also contain information on phenomena occurring at other than the location of the observation. For example, at a large airport the observation location may be defined as follows:

14

Chapter 3. General Procedures › 3.4. General Observing Practices.

a. For elements such as clouds, prevailing visibility, present weather, and obscurations, the observing location may be coincident with the observer’s physical location or it may be the touchdown area of the primary runway.

b. For temperature, dew point, and wind, the observing location may be the center of the runway complex.

c. For cloud height and ceiling, the observing location may be a point near the approach end of a runway.

d. For the location of lightning, the observing point may be the Airport Reference Point (ARP). The ARP is a permanent airport reference point defined by a latitude/longitude.

e. For tower visibility, the observing location must be the airport traffic control tower (ATCT). (NA LAWRS)

f. Regardless of observing location or the locations of the sensors, there must be only one observation disseminated long-line for an airport. If applicable, a report from a commissioned automated system with SPECI capability must be the observation for that airport. A report from a commissioned automated system without SPECI capability may also be designated as the weather observation for an airport. When the air traffic control facility is not in operation, these systems will be operated in the fully automated mode as the weather observation source.

3.4. General Observing Practices. The general observing practices specified in the following subsections apply to personnel taking either full manual, augmented, backup, or tower visibility observations. They do not necessarily apply to the automated portions of observations, which are controlled by system software. Observers must be alert to situations conducive to significant changes in weather conditions and must take and disseminate SPECI observations as rapidly as feasible whenever changes are noted that meet the criteria specified in Paragraph 3.12 Criteria for SPECI Observations.

a. Order of Observing. Elements having the greatest rate of change must be evaluated last. When conditions are relatively unchanging, the observer must evaluate the elements outdoors first, and then evaluate the elements indoors, with pressure being the last element evaluated.

b. Recency of Observed Elements. Individual elements entered in an observation must, as closely as possible, reflect conditions existing at the actual time of observation. At manual locations, elements entered must have been observed within 15 minutes of the actual time of observation. Gusts and squalls must be reported if observed within 10 minutes of the actual time of observation. METAR observations must be made as close to the scheduled time of the observation as possible to meet filing deadlines, but in no case will these observations be started more than 15 minutes before the scheduled time.

c. Dark Adaptation. When taking observations outdoors at night, sufficient time should be allowed for the observer’s eyes to become adjusted to the darkness.

15

Chapter 3. General Procedures › 3.6. Dissemination Requirements.

d. Weather Not Observed. Observers are not required to report occurrences they have not observed. However, the observer may use information from reliable sources, for example, pilots, airline/airport personnel or other sources deemed acceptable by the observer.

e. Time Disseminated in Reports. All times must refer to the 24-hour clock, for example, 1:47 a.m. must be referred to as 0147; 1:47 p.m. must be referred to as 1347. The times 0000 and 2359 must be used to indicate the beginning and ending of the day, respectively.

f. Time Standards. Times used in weather observations must be:

(1) Local Standard Time (LST). (NA LAWRS). LST is used on MF1M-10Cs to record times of observation and time checks. LST must be entered on all forms throughout the year with no consideration of daylight savings time.

(2) Coordinated Universal Time (UTC). UTC is used on all transmitted data. It is also used on MF1M-10Cs to record times of observations and time checks at LAWRS sites.

g. Accuracy of Time in Observations. The accuracy of the actual time of observation is very important in aviation safety investigations. One clock must be designated as the observing location standard, and a routine procedure set up to assure its accuracy once a day at a minimum. The clock used must be within ± 1 minute of the U.S. Naval Observatory Time. If available, the FAA Coded Time Source (CTS) may be substituted for U.S. Naval Observatory Time.

h. SPECI Observations Upon Resumption Of Observing Function. Observers must take, record, and disseminate a SPECI observation within 15 minutes after returning to duty following a break in normally scheduled observer coverage at the station unless a METAR observation is filed during that 15-minute period

3.5. Dissemination. For purposes of this order, dissemination is the act of delivering a completed report to users. There are two general types of dissemination.

a. Local. Local transmission is the transmission or delivery of a weather report to individuals or groups of users in the service area of the observing location.

b. Long-line. Long-line transmission is the transmission of a weather report beyond the service area of the observing location.

3.6. Dissemination Requirements. All reports must be given local dissemination. At stations with long-line capabilities, reports must be given long-line dissemination. When reports are corrected, the corrected report must be given the same dissemination as the report being corrected. If reports cannot be disseminated simultaneously, local and long-line, they must be disseminated first to the local airport traffic control users, then disseminated long-line. SPECI observations must be completed and transmitted as soon as possible after conditions meeting SPECI criteria are observed or detected. A METAR must be transmitted in accordance with agency guidelines. A METAR entered that also meets the criteria for a SPECI must be disseminated as a METAR. WS Form B-11, METAR/SPECI Report for Transmission, is available from the NWS for those facilities that receive manual observations from observers over the phone. This form is an optional aid for transcribing the observation for transmission. (See Appendix F. Transmission (WS FORM B-11).)

16

3.7. Corrections to Transmitted Data. Once an error has been detected in a transmitted report, a correction must be transmitted as soon as possible. Do not transmit a correction if the original transmitted observation has been superseded by a later report. Transmit the entire corrected report with (COR) as the report designator. Use the original date and time of the report being corrected.

Chapter 3. General Procedures › 3.11. Evaluating Weather Sensor Accuracy

3.8. Delayed Reports. When transmission of a manual observation is delayed until time for the next regularly scheduled report, only the latest report must be transmitted. In the record of observations, the remark Filed But Impractical to Transmit (FIBI) must be appended in parentheses to the report that was not transmitted. The remark FIBI must not be included in any local dissemination of the report. When a SPECI is not transmitted long-line, later SPECIs must be transmitted long-line only when the overall change between the last transmitted report and the current report satisfies the criteria for a SPECI. If the SPECI is not transmitted long-line, the remark FIBI must be appended to the report as described above. All SPECI reports must be disseminated locally. Reports of volcanic eruption must be disseminated, by any means possible, regardless of the delay.

3.9. Rounding Off Numbers. Except where otherwise designated in this order, when computations require that a number be rounded, if the fractional part of a positive number to be dropped is equal to or greater than one-half, the preceding digit must be increased by one. If the fractional part of a negative number to be dropped is greater than one-half, the preceding digit must be decreased by one. In all other cases, the preceding digit must remain unchanged. For example, 1.5 becomes 2, 1.3 becomes 1, -1.5 becomes -1, and -2.6 becomes -3. Refer to Paragraph 13.19 Rounding Pressure Values for rounding of pressure values.

3.10. Record Keeping and Forms

a. Manual Observations. All manual observations, whether complete or partial, must be recorded on form MF1M-10C (does not include automated stations). After completing the form, it must be archived at the facility completing the form. Facilities must prepare an electronic form and SEND TO “[email protected]” Corrected copies of all forms must be retained locally for 90 days. Retention of copies beyond 90 days must be as directed by the Washington Headquarters. All electronic forms must be sent to National Climatic Data Center (NCDC) to the following address: [email protected] by the second working day of each month

b. Automated Weather Observations. Automated weather observations and operator terminal entries are archived on site. No further action is required by FAA, FAA-contract, or NF-OBS facilities. In the event of a complete failure of automated equipment, observers are expected to follow manual observation recording requirements.

3.11. Evaluating Weather Sensor Accuracy

Sensor Evaluations. When the observer has reason to believe that the accuracy or validity of indications from meteorological sensors is questionable, the use of such equipment should be discontinued until necessary corrective maintenance has been accomplished. If the use of such equipment is discontinued, any required back-up procedures or practices must be initiated. FAA personnel and NF-OBS providers must make appropriate maintenance notifications in the event of any equipment outages. .

17

Chapter 3. General Procedures › 3.12. Criteria for SPECI Observations.

NOTE- If the observer believes that the AWSS/AWOS information is inaccurate, then contact the local Technical Operations personnel.

a. If the observer believes that the ASOS information is inaccurate, they should notify the ASOS Operations and Monitoring Center (AOMC) at 1-800-242-8194 OR 8895.

b. Notices to Airmen (NOTAMS). The FSS must accept, categorize, and distribute NOTAMs on all systems and system components following instructions in FAA Order JO 7930.2.

3.12. Criteria for SPECI Observations. The observer must take, record, and disseminate a SPECI observation when any of the following is observed to occur:

a. Wind Shift. Wind direction changes by 45 degrees or more in less than 15 minutes, and the wind speed is 10 knots or more throughout the wind shift.

b. Visibility. Visibility as reported in the body of the report decreases to less than, or if below, increases to equal or exceed:

(1) 3 miles.

(2) 2 miles.

(3) 1 mile.

(4) The lowest standard instrument approach procedure minimum as published in the U.S. Terminal Procedures. If none published, use 1/2 mile.

c. Runway Visual Range (NA LAWRS). The highest value from the designated RVR runway decreases to less than, or if below, increases to equal or exceed 2,400 feet during the preceding 10 minutes.

d. Tornado, Funnel Cloud, or Waterspout.

(1) Is observed.

(2) Disappears from sight or ends.

e. Thunderstorm.

(1) Begins (a SPECI report is not required to report the beginning of a new thunderstorm if one is currently reported).

(2) Ends.

f. Precipitation.

(1) Hail begins or ends.

(2) Freezing precipitation begins, ends, or changes intensity.

18

Chapter 3. General Procedures › 3.13. Content of METAR/SPECI Observations.

(3) Ice pellets begin, end, or change intensity.

g. Squall. Wind speed suddenly increases by at least 16 knots and is sustained at 22 knots or more for at least one minute.

h. Ceiling. The height of the base of clouds covering five eighths or more (for example, broken and overcast) of the sky forms or dissipates below, decreases to less than or, if below, increases to equal or exceed:

(1) 3,000 feet.

(2) 1,500 feet.

(3) 1,000 feet.

(4) 500 feet.

(5) The lowest standard instrument approach procedure minimum as published in the U.S. Terminal Procedures. If none published, use 200 feet.

i. Sky Condition. A layer of clouds or obscuring phenomenon aloft is present below 1,000 feet and no layer aloft was reported below 1,000 feet in the preceding METAR or SPECI observation.

j. Volcanic Eruption. When eruption is first noted.

k. Aircraft Mishap. Upon notification of an aircraft mishap, unless there has been an intervening observation.

l. Miscellaneous. Any other meteorological situation that, in the opinion of the observer, is critical.

3.13. Content of METAR/SPECI Observations. Table 3-1contains the content of METAR observations. The first column of the table lists the elements of the observation both for the body of the report and the remarks section. The second column lists a reference to the section in Chapter 14 that discusses coding of the particular element. The third column presents a brief description of the element. The fourth column indicates whether the element is reported in METAR observations, and the fifth column indicates whether the element is reported in SPECI observations.

Table 3-1: Content of METAR

Body of METAR - Consists of 11 Elements

Element Paragraph Brief Description METAR SPECI

Type of Report (METAR/SPECI) 14-7 METAR is the routine (scheduled) report. SPECI is the non-routine (unscheduled) weather report.

X X

Station Identifier (CCCC) 14-8 ICAO station identifier. Consists of four alphabetic characters, for example, KABC. X X

Date/Time (YYGGggZ) 14-9 Day of the month, followed by the actual time of the report or when the criteria for a SPECI is X X

19

Body of METAR - Consists of 11 Elements

Element Paragraph Brief Description METAR SPECI

met or noted. Group ends with Z to indicate UTC. For example, 251456Z.

Report Modifier (AUTO or

COR) 14-10

AUTO indicates a fully automated report. If not automated report, this field is blank. X X

COR indicates the report is a correction of a previously issued METAR or SPECI X X

Wind (dddff(f)GfmfmfmKT)

(dndndnVdxdxdx) 14-11

True wind direction in tens of degrees using three digits. Speed reported in whole knots (two or three digits). Gusts (G) appended to the speed if observed. Group ends with KT, for example, 23018G26KT. If wind direction varies by 60 ° or more and speed is >6 knots, a variable wind group may also be reported, for example, 180V250. Direction may be reported VRB (variable) if speed is <6 knots or less. For example, VRB05KT. Calm winds are coded 00000KT.

X X

Visibility (VVVVVSM) 14-12

Prevailing visibility in statute miles. A space divides whole miles and fractions. Ends with SM: 1 1/2SM. AUTO: M pref. means "less than": M1/4SM.

X X

Runway Visual Range (RDRDR/VRVRVRVRFT or RDRDR/VNVNVNVNVVXVXV

XVXFT)

14-13

At service level A&B sites (where so equipped), 10-minute RVR value: Reported in hundreds of feet if visibility is < one statute mile or RVR is < 6000 feet. Group ends with FT to indicate feet, for example, R06L/2000FT. Prefixed with either M or P indicates the value is lower or higher than the RVR reportable values, for example, R06L/P6000FT. If variable during the evaluation period, the variability is reported, for example, R06L/2000V4000FT.

A/B A/B

Present Weather (w'w') 14-14

Weather phenomena (other than obscurations) occurring at the station are reported in the body of the report. Weather obscurations are generally reported if visibility < 7 miles (see 14­ 14 for exceptions). Volcanic ash reported with any visibility. Reported in order of decreasing predominance. Maximum of three groups reported (pcpn included in one group; separate groups for other phenomena).

X X

Sky Condition (NsNsNshshshs or VVhshshs

or CLR or SKC)

14-15

Automated stations report no more than three layers up to 12,000 feet; if no layers are detected, CLR is reported. At manual stations up to six layers may be reported; if no layers observed, SKC is reported. Each layer contains the amount (FEW, SCT, BKN, OVC) immediately followed by the height using three digits, for example, FEW015, BKN030. A layer containing CB or TCU is indicated by appending the contraction to the layer height, for example, FEW015TCU. All layers are considered opaque. Vertical Visibility (VV) is

X X

20

Body of METAR - Consists of 11 Elements

Element Paragraph Brief Description METAR SPECI

reported in hundreds of feet for a total obscuration (indefinite ceiling), for example, VV002. Surface-based obscuration (manual only) reported using amount (FEW, SCT, BKN) followed by "000", for example, SCT000; remark reported as "FG SCT000."

Temperature/Dew Point

(T'T'/T' dT' d) 14-16

Temperature and dew point are reported to the nearest whole degree Celsius using two digits, for example, 17/13. Sub-zero values are prefixed with an M, for example, 03/M02.

X X

Altimeter (APHPHPHPH) 14-17

Altimeter is prefixed with an A indicating altimeter in inches of mercury. Reported using four digits; tens, units, tenths, and hundredths of inches of mercury, for example, A2990.

X X

Table 3-2: Remarks Section of Observation

Remarks Section of Observation

Element Paragraph Brief Description METAR SPECI

Volcanic Eruptions 14-20

Volcanic eruptions must be reported whenever first noted. Pre-eruption activity must not be reported. (Use PIREPs to report pre-eruption activity.) Encode volcanic eruptions as described in Chapter 11.

X X

Tornadic Activity (Manual

and Augmented Auto)

(Tornadic activity_B/E(hh)mm

LOC/DIR_(MOV))

14-21

Whenever tornadoes, funnel clouds, or waterspouts begin, are in progress, end, or disappear from sight, the event should be described directly after the "RMK" element. This remark must give, insofar as known, the phenomena, time, location and direction from the station, and direction of movement. The time the tornadic activity began must be reported and prefixed with a "B"; the time the tornadic activity ended or disappeared from sight must be reported and prefixed with an "E", for example, TORNADO B13 DSNT NE.

X X

Type of Automated Station

(AO1, AO2) 14-22

This remark identifies the type of automated station. It must be included in all reports from automated stations. AO1 identifies an automated station without a precipitation discriminator; AO2 identifies an automated station with a precipitation discriminator. The absence of the remark indicates a manual station.

X X

Peak Wind (PK WND

dddff(f)/(hh)mm)

(NA LAWRS

14-23 When the peak wind exceeds 25 knots, the remark must be included in the next METAR report. ddd is the direction of the peak wind, ff(f)

X

21

Remarks Section of Observation

Element Paragraph Brief Description METAR SPECI

is the peak wind speed since the last METAR report, and (hh)mm is the time of occurrence (with only the minutes reported if the hour can be inferred from the report time), for example, PK WND 28045/15.

Wind Shift (WSHFT_(hh)mm) 14-24

At stations with automated systems with SPECI capability and manual stations, when a wind shift occurs, WSHFT followed by a space and the time the wind shift began must be reported (with only the minutes reported if the hour can be inferred from the report time). The contraction FROPA may be entered following the time if it is reasonably certain that the wind shift was the result of frontal passage, for example, WSHFT 30 FROPA.

X X

Tower or Surface Visibility

(TWR VIS) (SFC VIS)

9-3 14-25

If tower visibility or surface visibility is carried in the remarks, use the appropriate set of values and precede the visibility with the appropriate identifier, TWR VIS or SFC VIS, for example, TWR VIS 1.

A/B/C A/B/C

Variable Prevailing Visibility (VIS minVmax) 14-26

Whenever the prevailing visibility is less than 3 statute miles and is variable, this remark must be entered where min is the lowest visibility evaluated and max is the highest visibility evaluated, for example, VIS 1/2V2.

X X

Sector Visibility

(VIS_dd_vv) 14-27

Sector visibility must be reported when it differs from the prevailing visibility by one or more reportable values and either the prevailing or sector visibility is less than 3 miles or considered to be operationally significant. In the remark, dd defines the sector to 8 points of the compass and vv is the sector visibility in SM, for example, VIS N 2.

X X

Visibility at Second Location (VIS vv location)

(NA LAWRS)

14-28

When an automated station uses meteorological discontinuity sensors, remarks must be added to identify site specific visibilities which differ from conditions reported in the body of the report. vv is the visibility value measured at the secondary location. This remark must only be generated when the condition is lower than that contained in the body of the report.

X3 X3

Lightning (Frequency_LTG(type)_

[LOC])

14-29

When lightning is observed at a staffed site, the frequency and location must be reported, along with the type of lightning, if known. For example, OCNL LTG AT AP, FRQ LTGCG VC. When lightning is detected by an automated system within 5NM of the ARP, it is reported as "TS" in the body of the report with no remark; within 5-10NM of the ARP, it must be reported as "VCTS" in the body of the report with no remark; and lightning beyond 10NM from the ARP is reported in remarks as "LTG DSNT"

X X

22

Remarks Section of Observation

Element Paragraph Brief Description METAR SPECI

followed by direction from the ARP, for example, LTG DSNT NE.

Beginning/Ending Time of

Precipitation (WX)B(mm)E(mm)

(NA LAWRS

14-30

At stations with automated systems with SPECI capability and Manual Stations, when precipitation begins or ends, the next METAR report must include the type of phenomena, the beginning and/or ending time (prefixed with a B and/or E). If the beginning or ending of the precipitation type (hail, freezing precipitation, or ice pellets) initiated the SPECI report, then that SPECI report must include the type of phenomena, the beginning and/or ending time, and should be reported in the next METAR report, also.

X X2

Beginning/Ending Time of

Thunderstorms (TS)B(mm)E(mm)

14-31

When thunderstorms begin or end, the SPECI report must include the type of phenomena, the beginning and/or ending time (prefixed with a B and/or E), and should also be reported in the next METAR report, for example, TSB05E45

X X

Thunderstorm Location (TS_LOC_(MOV_DIR)) 14-32 Thunderstorm location and movement must be encoded. For example, TS SE MOV NE. X X

Hailstone Size (GR_

{INCHES}) 14-33

At augmented automated stations and at manual stations, the size of the largest hailstone is coded in 1/4 inch increments, identified with the contraction GR. (If GS is encoded in the body of the report, no size remark is required.)

X X

Virga (VIRGA_{Direction}) 14-34

When precipitation is observed to be falling from clouds but is not reaching the ground because of evaporation, report VIRGA; the direction from the station is optional, for example, VIRGA or VIRGA SW.

X X

Variable Ceiling Height

(CIG minVmax) 14-35

Whenever the ceiling is below 3,000 feet and is variable, enter min as the lowest ceiling height evaluated and max as the highest ceiling height evaluated, for example, CIG 005V010.

X X

Obscurations (w’w’_(NsNsNs) hshshs) 14-36

When the sky condition contains an obscuration either at the surface or aloft, other than clouds, the type of phenomena in the layer, plus the sky cover at the layer and the height must be reported in remarks, for example, FG SCT000 or FU BKN015.

X X

Variable Sky Condition (NsNsNs(hshshs)_V_NsNsNs) 14-37

This remark must identify the layer that is varying and indicate the range of variability. If there are several layers of the same coverage, the variable layer must be identified by including the layer height.

X X

Significant Cloud Types 14-38

When observed, the following clouds are reported in remarks: 1.) Cumulonimbus (CB) or Cumulonimbus Mammatus (CBMAM), distance, direction from the station, direction of movement, for example, CB W MOV E, CB DSNT W. 2.) Towering Cumulus (TCU),

A A

23

Remarks Section of Observation

Element Paragraph Brief Description METAR SPECI

distance, and direction from the station, for example, TCU W. 3.) Altocumulus Castellanus (ACC), direction from station, for example, ACC NW. 4.) Standing Lenticular (stratocumulus SCSL; altocumulus ACSL, or cirrocumulus CCSL) or rotor clouds, direction from the station, for example, ACSL SW-W, APRNT ROTOR CLD NE, CCSL S. Cumulonimbus of any kind and towering cumulus are also identified in the body of the report.

Ceiling Height at Second Location (CIG_ {height}_

{LOC}) (NA LAWRS

14-39

When an automated station uses meteorological discontinuity sensors, remarks must be added to identify site specific sky conditions which differ from conditions reported in the body of the report. This remark must only be generated when the ceiling is lower than that contained in the body of the report. For example, CIG_002_RY11.

X3 X3

Pressure Rising or Falling

Rapidly (PRESRR)

(PRESFR) (NA LAWRS)

14-40

When the pressure is rising or falling rapidly at the time of the observation, the remark Pressure Rising Rapidly (PRESRR) or Pressure Falling Rapidly (PRESFR) must be included.

X X

Sea-Level Pressure

(SLPppp) (SLPNO)

(NA LAWRS)

14-41

At stations with automated systems with SPECI capability and manual stations, this remark begins with SLP and is coded using the tens, units, and tenths of sea-level pressure in hectopascals, for example, SLP982. If sea-level pressure would normally be reported, but is not available, the remark is coded SLPNO.

X

Aircraft Mishap (ACFT_

MSHP) 14-42

If a report was taken to document weather conditions when notified of an aircraft mishap, the remark ACFT MSHP is included in the report, but is not transmitted. This is indicated by putting the remark in parenthesis in the record.

X X

No SPECI Reports Taken

(NOSPECI) 14-43

At staffed stations where SPECI reports are not taken, the remark NOSPECI must indicate that no changes in weather conditions will be reported until the next METAR report.

X2

Snow Increasing Rapidly

(SNINCR_(ii)/(ii))

(NA LAWRS)

14-44

Report SNINCR if snow depth increases by 0.5 inch to the nearest whole inch or more in the past hour, followed by amounts. The remark SNINCR is followed by the depth of increase in the last hour, a solidus, and the total depth of snow on the ground at the time of the report. For example, a snow depth increase of 2 inches in the past hour with a total depth on the ground of 10 inches would be coded "SNINCR 2/10."

X

Other Significant Information (Plain

Language)

14-45

Other significant information important to operations, such as information on fog dispersal operations, runway conditions, or "Last" report from location, etc.

X X

24

Remarks Section of Observation

Group 2`-Additive and Automated Maintenance Data

Element Paragraph Brief Description METAR SPECI

Hourly Precipitation

Amount (Prrrr)

(NA LAWRS)

14-47

At automated stations this remark is included in METAR reports for the water equivalent of all precipitation that has occurred since the last METAR coded in hundredths of an inch, for example, P0009 indicates 9/100ths of an inch of precipitation in the past hour.

X

1-, 3- and 6-Hourly Ice Accretion Amount, I1nnn, I3nnn, I6nnn

(NA LAWRS)

14-48

At automated stations with a freezing rain sensor, this remark is included in METAR/SPECI reports for the ice accretion amount that has occurred in hundredths of an inch during the last 1-hour (I1nnn), 3-hour (I3nnn), and 6-hour (I6nnn) period. No manual backup is required.

X X

3- and 6-Hourly Precipitation Amount,

6RRRR/ (NA LAWRS)

14-49

At stations equipped with automated systems with SPECI capability and Manual stations, this remark is included in 3- and 6-hourly observation; encoded in inches, using tenths, and hundredths, of the amt. 2.17 inches of precipitation would be encoded 60217. When an indeterminable amount of precipitation has occurred, the 6RRRR group is coded 6////. Note: automated systems with SPECI capability automatically report this data.

X

24-Hour Precipitation, 7R24R24R24R24 (NA LAWRS)

14-50

Included in 1200 UTC observation if more than a trace of precipitation has fallen in past 24 hours, coded using the tens, units, tenths, and hundredths of inches, for example, 1.25 inches would be coded 70125.

X

Depth of Snow on the

Ground, 4/sss

(NA LAWRS)

14-51

At stations listed in Appendix G, the total snow depth on ground group is coded in the 0000, 0600, 1200, and 1800 UTC observations whenever there is more than a trace of snow on the ground, and more than a trace of precipitation occurred within the past 6 hours. For example, a snow depth of 21 inches would be coded as "4/021."

X

Water Equivalent of Snow

on Ground (933RRR)

(NA LAWRS)

14-52

At manual stations, this group reported in 1800UTC report if average snow depth is 2 inches or more. 933 is the code indicator for water equivalent of snow on ground. RRR represents the water equivalent of snow on the ground reported in tens, units and tenths of inches using 3 digits, for example, water equivalent of 3.6 inches would be 933036.

X

25

Remarks Section of Observation

Element Paragraph Brief Description METAR SPECI

Hourly Temperature and

Dew Point TsnT’T’T’snT’dT’dT’d

(NA LAWRS)

14-53

At automated stations except AWOS-A, this element is used to report temperature and dew point to the tenth of a degree Celsius. T identifies the group, the sn the sign of the temperature - coded as 1 if the value is below 0 degrees Celsius and 0 if the value is 0 degrees Celsius or higher. TaTaTa is the temperature in tens, units, and tenths of degrees and T'aT'aT'a is the dew point in tens, units and tenths of degrees, for example, a

X

temperature of 2.6 and dew point of -1.5 would be coded in the body as 03/M01 and in remarks as T00261015. If the dew point is missing, report the temperature, if the temperature is missing, do not report either.

6-Hour Maximum Temperature, 1snTxTxTx

(NA LAWRS)

14-54

Report the maximum temperature in past 6hours in tenths of degrees Celsius using 3 digits, where the 1 identifies the maximum temperature group, the sn the sign of the temperature - coded as 1 if the value is below 0 degrees Celsius and 0 if the value is 0 degrees Celsius or higher. The TxTxTx must be the maximum temperature during the last 6

X

hours, for example, a temperature of 1.0 degrees Celsius is coded as 10010, a maximum temperature of -2.1 degrees Celsius is coded 11021.

6 Hour Minimum Temperature, 2snTnTnTn

(NA LAWRS)

14-55

Report the minimum temperature in past 6hours in tenths of degrees Celsius using 3 digits where the 2 identifies the minimum temperature group, the sn the sign of the temperature - coded as 1 if the value is below 0 degrees Celsius and 0 if the value is 0 degrees Celsius or higher. The TnTnTn must be the minimum temperature during the last 6

X

hours, for example, a temperature of -2.1 degrees Celsius is coded as 21021, a minimum temperature of 1.2 degrees Celsius is coded 20012.

24-Hour Maximum and Minimum Temperature,

4snTxTxTxsnTnTnTn (NA LAWRS)

14-56

Reported at midnight (LST); the maximum and minimum temperatures for the day coded in tenths of degrees Celsius using 3 digits where the 4 identifies the maximum/minimum temperature group, the sn the sign of the temperature - coded as 1 if the value is below 0 degrees Celsius and 0 if the value is 0 degrees Celsius or higher. For example, a 24hour maximum temperature of 10.0 degrees Celsius and a 24-hour minimum temperature of -1.5 degrees Celsius is coded 401001015.

X

26

Remarks Section of Observation

Element Paragraph Brief Description METAR SPECI

Pressure Tendency, 5appp

(NA LAWRS) 14-57

At equipped automated stations, include in 3and 6-hourly observations where the 5 identifies the pressure tendency group, the a represents the character of pressure change over the past 3 hours, and ppp is the change in pressure in the past 3 hours. the ppp is coded based on the absolute value of the change of either the station pressure or the altimeter in the past 3 hours coded in tenths of hectopascals and using the tens, units, and tenths digits, for example, a steady increase of 3.2 hectopascals in the past 3 hours would be coded 52032.

X

Sensor Status Indicators 14-58

At equipped automated stations: When automated stations are equipped with a precipitation identifier and that sensor is not working, the remark PWINO is included. When the tipping bucket rain guage is not operating at an automated station equipped with the device, PNO is included in remarks. When automated stations are equipped with a Freezing Rain Sensor and it is not working, the remark FZRANO is included. When automated stations are equipped with a lightning detection system and that sensor is not working, the remark TSNO is included. At an automated station, when the secondary visibility sensor is not working, VISNO_(LOC) is included, and when the cloud height indicator is not working CHINO_(LOC) is included.

X

Maintenance Indicator 14-59 A maintenance indicator sign, $, is included when an ASOS/AWSS detects that maintenance is needed on the system.

X X

X – Indicates elements included at all stations A – Indicates elements that are at service level A (where so equipped) B – Indicates elements that are at service level B (where so equipped) 2 Report if precipitation caused the SPECI. 3 At stations equipped with meteorological discontinuity sensors.

27

Chapter 4. General Procedures at Automated Weather Stations › 4.2. Types of Automated Stations

Chapter 4. General Procedures at Automated Weather Stations

4.1. Purpose. This chapter prescribes procedures and practices to be followed by personnel responsible for observing, reporting, and/or transmitting surface weather information required for augmentation, and/or for sustaining minimum operations in the event of partial or total failure of the automated weather observing system. Practices applicable to LAWRS observers are located in Appendix C.

4.2. Types of Automated Stations

a. FAA, FAA-contract and NF-OBS Stations. There are two major classes of automated surface weather observing systems used at FAA, FAA-contract, and NF-OBS sites: Automated systems with SPECI capability and automated systems without SPECI capability. The augmentation and backup of these systems are described in the next two chapters for all FAA, FAA-contract, and NF-OBS site personnel.

(1) Automated systems with SPECI capability.

(a) Automated Surface Observing System (ASOS) is a type of automated surface

weather observing system developed through a joint FAA/NWS/DOD agreement. FAA ASOSs are installed at designated airports and maintained by the NWS to meet FAA requirements. There are three configurations of ASOS. The first contains at least one of each of the following sensors:

(i) Wind sensor. (ii) Visibility sensor. (iii) Precipitation identification sensor.

(iv) Cloud height indicator sensor.

(v) Temperature and dew point sensors. (vi) Pressure sensors. (vii) Precipitation accumulation sensor. (viii) (Format correctly) (b) The second ASOS configuration which includes the FAA Automated Weather

Sensor System (AWSS) has a freezing precipitation sensor in addition to all of the above sensors. The third configuration has a thunderstorm/lightning sensor. Systems without individual lightning sensors will get thunderstorm reporting via the Automated Lightning Detection and Reporting System (ALDARS). Many sites have an ASOS/ATIS Interface Unit (AAIU) which provides the capability to broadcast current weather from the ASOS over the ATIS ground-to-air radio when the tower is closed. ASOS may also have an interface to new generation RVR equipment. See Chapter 9. Runway Visual Range (RVR).

(c) AWOS-Type FA-29600 -Is an AWOS modified by the FAA to report

METAR/SPECI data.

28

NOTE Any reference to ASOS includes the FAA AWSS and AWOS-Type FA-29600, and any future NextGen system with SPECI capability.

(2) Automated systems without SPECI capability.

(a) Automated Weather Observing System (AWOS). AWOS is a type of automated

surface weather observing system certified and commissioned by the FAA.

(b) The AWOS was developed under a Flight Standards Service-sponsored project

specifically to provide weather information at locations without previous weather observation capabilities. There are five types of AWOS, namely, A, 1, 2, 3, and 4. These five types are used throughout the Advisory Circular and recognized in other FAA orders.

(i) AWOS A. The AWOS A system measures and reports altimeter only.

(ii) b. AWOS I. The AWOS I system measures and reports wind data, e.g., speed,

direction, and gusts; temperature; dew point; altimeter; and density altitude. “Correct lettering”

(iii) AWOS II. The AWOS II system measures and reports all the parameters of

AWOS I system plus visibility.

(iv) d. AWOS III. The AWOS III system measures and reports all the parameters of

AWOS II system plus precipitation accumulation (rain gauge) and cloud height. AWOS III can have optional sensors such as precipitation type/intensity (present weather, P) and/or thunderstorm/lightning (T). i. The addition of an optional sensor will change the designation to AWOS III P or AWOS III T, or AWOS III P/T.

(v) e. AWOS IV. The AWOS IV system measures and reports all the AWOS III

P/T (i.e. AWOS III with both present weather and thunderstorm/lightning) parameters plus freezing rain (Z) and/or runway surface condition (R). The addition of an optional sensor will change the designation to AWOS IV Z, AWOS IV R, or AWOS IV Z/R.

(3) Many AWOSs were installed at airports without previous weather observations, so personnel may not be available to augment or back up the automated weather observations. The most common type of AWOS observation is the AWOS-3. It is identified by AUTO (automated report) in the body of the report and AO1 (automated station without precipitation discriminator) in the remarks section if it is a fully automated report. If it is being augmented/backed up by an observer, it will not have AUTO in the body of the report, and it will have AO1 in the remarks section. (See examples in Table 5-2: Examples of Augmented Observations.)

29

Chapter 4. General Procedures at Automated Weather Stations › 4.5. General Equipment Procedures.

NOTE­ LAWRS observers do not augment automated systems without SPECI capability. See FAA Order 7210.3, Facility Operation and Administration.

b. Non-FAA Stations. In addition to the systems described above, there are various NWS, DOD, and non-Federal automated weather observing systems. All non-Federal automated weather observing systems to be used for aviation must be certified and commissioned by the FAA in accordance with the most current version of FAA Advisory Circular AC 150/5220-16, Automated Weather Observing Systems (AWOS) for Non-Federal Applications.

4.3. Certification. All FAA and contract personnel, including LAWRS personnel, responsible for providing weather observations, augmentation information, tower visibility observations or backup weather information must be certified at least to the level commensurate with current duties. Certification must be in accordance with the provisions of Paragraph 2.7 Certification of Personnel and Currency Requirements.

4.4. General Procedures. At automated weather observing stations, the specified weather information must be taken, recorded and disseminated in accordance with the procedures and practices in this order. Operator procedures for recording and disseminating augmentation and backup information are summarized in Table 4-1: Operator Procedures for Providing Augmentation and Backup Information. Weather information taken and reported should reflect only those conditions seen, or reported by a reliable source, from the usual point of observation and, unless otherwise specified, must have occurred at the time of the observation.

Table 4-1: Operator Procedures for Providing Augmentation and Backup Information

CONDITION LONG-LINE LOCAL

AUGMENTATION Enter data via OID Enter data via OID

BACKUP INFORMATION:

Sensor Failure Edit data via OID Edit data via OID

OID communications failure Provide to Associated FSS Provide to Local Air Traffic Facility and follow other Local Procedures

Erroneous/Non-representative data Edit data via OID Edit data via OID

LEGEND: OID – any automated weather observing system operator interface device

FSS – Automated Flight Service Stations

4.5. General Equipment Procedures. General equipment operating instructions to perform the duties associated with automated weather observing systems are contained in the following publications:

30

Chapter 4. General Procedures at Automated Weather Stations › 4.9. General Requirements for Record Keeping.

a. For all Federal systems, use handbooks, manuals, or Ready Reference Guides as provided by the Government.

b. For all non-Federal systems, use handbooks, manuals, or Ready Reference Guides as provided by the manufacturer.

4.6. Procedures at Non-Federal Observation Sites. See Appendix B.

4.7. Procedures at Non-Federal AWOS Sites. FAA facilities must negotiate a letter of agreement (LOA) with the airport management or appropriate authority at locations where a non-Federal AWOS is installed at an airport with an operating control tower. The LOA must define responsibilities and equipment and coordination requirements; identify special operating conditions; and define local requirements. ATCSs may disseminate only those non-Federal weather observations that are obtained through the weather message switching center or other equivalent documented means. Pilots who want non-Federal AWOS information from sites that do not include automatic long-line dissemination should be provided the appropriate frequency and/or telephone number, if known.

4.8. Procedures for Handling Aircraft Mishaps at Automated Sites. The requirement to record the present weather following an aircraft mishap remains valid at automated sites. At a minimum, a mishap requires weather data from 1 hour before to 1 hour after the mishap occurs. ASOS observations should be archived by the observer or by calling the AOMC (1-800-242-8194). The AOMC has the capability to archive the 5-minute observations from the previous 12 hours of weather observation data from attended and unattended locations. The supervisor or controller-in-charge must ensure that the 5minute observations are archived following notification of an aircraft mishap at a location where an ASOS is operational. AOMC requests must be made within 10 hours of the incident. Archive AWOS data in accordance with the procedures in the AWOS Technical Instruction Book.

4.9. General Requirements for Record Keeping. Automated weather observation data and operator terminal entries are archived on site. No further action is required by FAA, FAA-contract, or NF-OBS facilities. If the automated weather observing system is completely inoperative, follow the record-keeping procedures for manual stations.

31

Chapter 5. Augmentation Requirements at Automated Weather Stations › 5.3. Sign On/Sign Off the Automated Weather Observing Systems.

Chapter 5. Augmentation Requirements at Automated Weather Stations

5.1. Introduction. This chapter prescribes procedures and practices applicable to the augmentation of automated surface observations at all FAA, FAA-contract, and NF-OBS facilities. In addition, this chapter also prescribes specific differences in augmentation procedures and practices applicable to LAWRS observers, as well as tower visibility requirements. FAA guidelines applicable to the augmentation of automated surface observations are presented in Paragraph 2.3 General Types of Observations. Table 5-1: Summary of FAA Augmentation Requirements, summarizes the minimum augmentation requirements by type of facility, which was given previously in Chapter 2. Guidelines.

5.2. Validity of Data. Once an observation has been augmented, the observer must ensure the augmented data is correct prior to transmission.

5.3. Sign On/Sign Off the Automated Weather Observing Systems. In order to ensure the observation is correct and to enter augmentation data into the automated weather observing system, the observer must be signed on when on duty. Sign on must be in accordance with the respective automated weather observing system’s operator handbook or locally prescribed procedures. The "AUTO" tag at the beginning of the observation will be dropped when the observer signs on.

a. Sign On/Sign Off the ASOS.

(1) When using ASOS, several augmented events (for example, tornadic activity, thunderstorm, or hail) automatically generate SPECI observations for the beginning and ending of the event. If one of these events is occurring at the close of augmentation coverage, it will be necessary to end the event, or it will continue to be reported during the hours when there is no augmentation coverage. The observer must end the event immediately after the last hourly METAR is transmitted before going off duty. The ending of the event will automatically generate a SPECI. The observer must cancel this SPECI, enter the AUTO REMARK, and disable the present weather (PREWX). The observer must then sign off the automated weather observing system. This procedure will end the erroneous ending remark in the next observation.

(2) Virga and volcanic ash are events that do not generate SPECIs. Virga is automatically deleted from the observation after the hourly METAR is transmitted. If virga continues to occur, it must be re-entered. If volcanic ash is occurring at the close of augmentation coverage, it will be necessary to end the event, or it will continue to be reported during the hours when there is no augmentation coverage. The observer must end the event immediately after the last hourly METAR is transmitted before going off duty.

32

Chapter 5. Augmentation Requirements at Automated Weather Stations › 5.4. Order for Reporting Weather and Obstructions to Visibility.

Table 5-1: Summary of FAA Augmentation Requirements

ELEMENT

TOWERED with automated system

with SPECI

capability

NONTOWERED with automated

system with

SPECI capability

Automated

System without

SPECI Capability4

with OBS

TOWERED

w/ Automated

System without

SPECI Capability4

w/o OBS w/o OBS1 w/ OBS2 FSS3 or FAA

Contract

Thunderstorm T O F O T

Tornadic Activity5 T O F O T

Hail T O F O T

Virga T O F O T

Volcanic ash T O F O T

Weather6 NA7 NA7 NA7 O T

Tower Visibility T8 T9

Continue reading ↓ 120 of 542 passages shown