Order JO 7900.5E Surface Weather Observing w/ Change 1
This order prescribes aviation surface weather observing procedures and practices. This order includes practices and procedures for both manual and automated observation locations. Also included are practices and procedures for augmentation of automated observations and backup information in the event of system failure, erroneous or non-representative data. These procedures and practices are intended to provide a framework for identifying meteorological phenomena of importance to aviation and reporting their occurrence. OPR Change: AJT-21 to AJR-B (9.20.23)
Text read by OCR from a scanned file (4 of 178 pages). Check the original, as some words may be misread.
Structure Bookmarks › Distribution: Electronic Initiated By: AJT-2
CHANGE
JO 7900.5E U.S. DEPARTMENT OF TRANSPORTATION
CHG 1 FEDERAL AVIATION ADMINISTRATION
Effective Air Traffic Organization Policy Date: 07/1/2021
SUBJ: Surface Weather Observing
1. Purpose. This change amends practices and procedures in Surface Weather Observing.
2. Who this change affects. This order applies to all FAA and FAA-contract personnel, Limited Aviation Weather Reporting Stations (LAWRS) personnel, Non-Federal Observation (NF-OBS) Program personnel, as well as United States Coast Guard (USCG) personnel, as a component of the Department of Homeland Security and engaged in taking and reporting aviation surface observations.
3. Disposition of Transmittal Paragraph. Retain this transmittal sheet until the directive is replaced by a new directive.
PAGE CHANGE CONTROL CHART
Remove Pages Dated Insert Pages Dated 15 thru 29 01/15/20 15 thru 29 07/01/21 72 thru 76 01/15/20 72 thru 76 07/01/21 93 01/15/20 93 07/01/21 96 01/15/20 96 07/01/21 120 01/15/20 120 07/01/21 123 01/15/20 123 07/01/21
4. Administrative Information.
5. Where I can find this order. This order is available on the FAA Web site at Air Traffic Publications and on the My FAA employee website at Orders and Notices.
6. Explanation of Changes. This change adds new criteria for weather observers including LAWRS to issue a SPECI weather observation to report the beginning,ending, or change in intensity of snow. In 2019, an SRM panel determined that this change to SPECI reporting criteria did not change the existing acceptable level of risk for the system.
This change also adds new criteria to issue a SPECI weather observation when the visibility increases/decreases at or below 1/2 statute mile or 1/4 statute mile. Adding the lower visibility SPECI criteria will assist in automatically generating a SNOW SPECI at controlled/uncontrolled airports.
Distribution: Electronic Initiated By: AJT-2
Structure Bookmarks › 2
07/1/2021 JO 7900.5E, Chg 1
ASOS/AWOS-C must also have these new SPECI thresholds added to the system local SPECI criteria until ASOS/AWOS-C software is upgraded.
Paragraph 3.10 is revised to clarify that the NWS MF1M-10C is only completed at manual stations. Table 3-1, Chapter 11, 12 and 13 have also been edited to clarify that weather observers do not augment/edit the additive data groups that the automated weather observation system automatically generates.
7. Distribution. This order is distributed to select offices in Washington Headquarters; Air Traffic Organization; Office of Operations Planning; NAS Weather Office; Flight Standards Service; the Mike Monroney Aeronautical Center; the William J. Hughes Technical Center; the USCG Elizabeth City Facility; the Department of Defense (DoD); all air traffic field facilities; all Alaska flight service stations (FSS); FAA-contract weather; and the National Weather Service (NWS).
Jeffrey U. Vincent Vice President Air Traffic Services Air Traffic Organization
JO 7900.5E, Surface Weather Observing › U.S. DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION
Distribution: Electronic Initiated By: AJT-2
U.S. DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION
Air Traffic Organization Policy
SUBJ: Surface Weather Observing
Effective Date:
01/15/2020
The Federal Aviation Administration (FAA) Surface Weather Observer Program is a component of the National Airspace System (NAS). It combines with other elements of the NAS to ensure the overall safety of air transportation services. The FAA is committed to providing the resources necessary to ensure the vibrancy of this critical aviation service. This order provides the practices and procedures for weather observation services that support the important role it plays in the mission of the FAA.
The practices and procedures set forth in this order apply to all FAA personnel, FAA-contract personnel, and non-Federal Observer personnel who provide aviation weather observation services. Weather observer personnel are required to apply the provision of this order as it pertains to their observational responsibilities. Observers are expected to exercise experienced judgment when encountering situations not covered by this order.
Jeffrey U. Vincent Vice President Air Traffic Services
ORDER JO 7900.5E
Order_JO_7900.5E › Table of Contents
ii
Table of Contents
Chapter 1. Introduction … 1 1.1. Purpose of This Order … 1 1.2. Audience … 1 1.3. Where to Find This Order … 1 1.4. Cancellation … 1 1.5. Explanation of Changes … 1 1.6. Abbreviations and Acronyms … 2 1.7. Relationship to FMH-1 and Other Documents … 2 1.8. Applicability of Procedures and Practices … 3 1.9. User Responsibilities … 3 1.10. Distribution … 4 1.11. Changing the Order … 4 1.12. Maintaining the Order … 4
Chapter 2. Guidelines … 5 2.1. Introduction … 5 2.2. Types of Stations … 5 2.3. Non-Federal Weather Observation (NF-OBS) Station … 5 2.4. General Types of Observations … 5 2.5. Augmentation Requirements … 6 2.6. Backup Requirements … 7 2.7. Evaluating Weather Sensor Accuracy … 8
Chapter 3. General Procedures … 10 3.1. Introduction … 10 3.2. Certification of Personnel and Currency Requirements … 10 3.3. Definitions … 10 3.4. Aviation Weather Observing Locations … 12 3.5. General Observing Practices … 12 3.6. Dissemination … 13 3.7. Corrections to Transmitted Data … 14 3.8. Delayed Reports (Manual Stations Only) … 14 3.9. Rounding Off Numbers … 15 3.10. Record Keeping and Forms … 15 3.11. Criteria for SPECI Observations … 15 3.12. Content of METAR/SPECI Observations … 17
Chapter 4. General Procedures at Automated Weather Stations … 30 4.1. Purpose … 30 4.2. Types of Automated Stations … 30 4.3. Procedures for Handling Aircraft Mishaps at Automated Sites … 31
Chapter 5. Augmentation Requirements at Automated Weather Stations … 32 5.1. Introduction … 32 5.2. Validity of Data … 32 5.3. Sign On/Sign Off the Automated Weather Observing Systems … 32
iii
5.4. Augmentation Observing Procedures … 33 5.5. General Reporting Procedures … 34
Chapter 6. Backup/Editing Requirements at Automated Weather Stations … 37 6.1. Introduction … 37 6.2. Validity of Data … 37 6.3. Equipment Requirements … 37 6.4. Procedures for Providing Backup Information … 39 6.5. Coding of Missing Data … 40 6.6. Procedures for Wind Speed and Wind Direction … 40 6.7. Procedures for Visibility … 40 6.8. Procedures for Present Weather and Obscurations … 41 6.9. Procedures for Sky Condition … 42 6.10. Procedures for Temperature and Dew Point (See Chapter 11) … 42 6.11. Procedures for Altimeter Setting (See Chapter 12) … 43 6.12. Malfunctions/Outages … 44
Chapter 7. Wind … 45 7.1. Introduction … 45 7.2. Definitions … 45 7.3. Observing, Determining, and Reporting Procedures … 45 7.4. Wind Direction … 45 7.5. Estimating Wind Direction … 46 7.6. Variable Wind Direction … 46 7.7. Wind Shifts … 46 7.8. Wind Speed … 47 7.9. Estimating Wind Speed … 47 7.10. Wind Character (Gusts) … 47 7.11. Peak Wind Speed … 47 7.12. Calm Wind … 47 7.13. Conversion of True and Magnetic Winds … 47
Chapter 8. Visibility … 49 8.1. Introduction … 49 8.2. Definitions … 49 8.3. Visibility Standards … 50 8.4. Unit of Measure … 50 8.5. Observing Aids for Visibility … 50 8.6. Selection of Visibility Markers … 50 8.7. Dark Adaptation … 51 8.8. Evaluating Visibility … 51 8.9. Evaluating Prevailing Visibility … 51 8.10. Evaluating Sector Visibility … 51 8.11. Evaluating Variable Visibility … 51 8.12. Reporting Visibility Values … 51 8.13. Control Tower Visibility Observations and Actions at Collocated Sites … 51 8.14. Surface Observer Action at Stations with Control Tower … 52
iv
Chapter 9. Weather Phenomena … 53 9.1. Introduction … 53 9.2. Precipitation … 53 9.3. Obscurations … 54 9.4. Other Phenomena … 56 9.5. Qualifiers … 56 9.6. Order for Reporting Multiple Types of Weather and Obscurations … 57 9.7. Rules for Phenomena Not Occurring at the Point of Observation … 58 9.8. Observing and Reporting Precipitation … 58 9.9. Beginning and/or Ending Precipitation (NA LAWRS) … 58 9.10. Determining and Reporting the Type of Precipitation … 59 9.11. Determining the Character of Precipitation … 59 9.12. Precipitation Intensity … 59 9.13. Intensity of Snow, Snow Pellets, Snow Grains, Drizzle, and Freezing Drizzle … 60 9.14. Reporting Freezing Precipitation … 61 9.15. Beginning and/or Ending of Freezing Precipitation … 61 9.16. Intensity of Freezing Precipitation … 61 9.17. Reporting Ice Pellets … 61 9.18. Beginning and/or Ending of Ice Pellets (NA LAWRS) … 61 9.19. Intensity of Ice Pellets … 61 9.20. Reporting Precipitation Amounts (Automated) … 61 9.21. Snowfall within Specified Periods (See Appendix F) … 62 9.22. Observing and Reporting Tornado, Waterspout, or Funnel Cloud … 62 9.23. Observing and Reporting Thunderstorms … 63 9.24. Beginning and/or Ending of a Thunderstorm … 64 9.25. Reporting Hail … 64 9.26. Beginning and/or Ending of Hail … 64 9.27. Reporting Lightning … 64 9.28. Reporting Squalls … 65 9.29. Observing and Reporting Procedures for Obscurations … 65 9.30. Observing Obscurations … 65 9.31. Reporting Obscurations … 65 9.32. Special Procedures for Volcanic Ash … 65 9.33. Operationally Significant Remarks for Obscurations … 65
Chapter 10. Sky Condition … 66
10.1. Introduction … 66 10.2. Sky Condition Evaluation … 66 10.3. Cloud Forms and Obscuring Phenomena … 66 10.4. Definitions … 66 10.5. Observing Sites … 68 10.6. Layer Amounts … 69 10.7. Summation Layer Amount … 70 10.8. Layer Heights … 70 10.9. Evaluation of Multiple Layers … 71 10.10. Amount of Obscuration … 71 10.11. Determining Amount of Sky Cover … 71
v
10.12. Evaluation of Sky Cover Amounts … 71 10.13. Sky Cover Classification … 71 10.14. Variable Sky Cover … 72 10.15. Non-Uniform Sky Cover … 72 10.16. Estimated Ceiling Heights … 72 10.17. Variable Ceiling Height … 73 10.18. Significant Clouds … 73
Chapter 11. Temperature and Dew Point … 74
11.1. Introduction … 74 11.2. Definitions … 74 11.3. Temperature and Dew Point Observing and Reporting Practices … 74 11.4. Obtaining Readings from a Sling Psychrometer … 74 11.5. Maximum and Minimum Temperature … 75 11.6. Maximum/Minimum Extremes … 75
Chapter 12. Pressure … 76
12.1. Introduction … 76 12.2. Definitions … 76 12.3. Observing, Determining, and Reporting Procedures … 77 12.4. Determining Altimeter Setting … 78 12.5. Pressure Related Remarks … 78
Chapter 13. Coding … 79
13.1. Introduction … 79 13.2. Aviation Weather Reports Code … 79 13.3. Format and Content of the METAR/SPECI Report … 79 13.4. Coding Missing Data in METAR and SPECI Reports … 80 13.5. Coding the Body of the METAR or SPECI Report … 80 13.6. Type of Report (METAR or SPECI) … 80 13.7. Station Identifier (CCCC) … 80 13.8. Date and Time of Report (YYGGggZ) … 80 13.9. Report Modifier (AUTO or COR) … 80 13.10. Wind Group ((dddff(f)Gfmfm(fm)KT)_(dndndnVdxdxdx)) … 81 13.11. Visibility Group (VVVVVSM) … 81 13.12. Runway Visual Range Group (RDRDR/VRVRVRVRFT) or (RDRDR/VnVnVnVnVVxVxVxVxFT) (Automated Only) … 82 13.13. Present Weather Group (w’w’) … 83 13.14. Sky Condition Group (NsNsNshshshs or VVhshshs or CLR or SKC) … 86 13.15. Temperature/Dew Point Group (T’T’/T’dT’d) … 88 13.16. Altimeter (APHPHPHPH) … 88 13.17. Remarks (RMK) … 88 13.18. Automated, Manual, and Plain Language Remarks … 89 13.19. Volcanic Eruptions … 89 13.20. Funnel Cloud (TORNADIC ACTIVITY_B/E(hh)mm_LOC/DIR_(MOV)) … 89 13.21. Type of Automated Station (AO1 or AO2) … 90 13.22. Peak Wind (PK WIND_ddff(f)/(hh)mm) (Automated Only) … 90 13.23. Wind Shift (WSHFT_(hh)mm) … 90
vi
13.24. Tower or Surface Visibility (TWR_VIS_vvvvv or SFC_VIS_vvvvv) … 90 13.25. Variable Prevailing Visibility (VIS_vnvnvnvnvnVvxvxvxvxvx) … 90 13.26. Sector Visibility (VIS_[DIR]_vvvvv) … 90 13.27. Visibility at Second Location((VIS_vvvvv_[LOC]) (Automated Only) … 91 13.28. Lightning Frequency (Frequency_LTG(Type)_[LOC]) … 91 13.29. Beginning and Ending of Precipitation (w’w’B(hh)mmE(hh)mm) (NA LAWRS) … 92 13.30. Beginning and Ending of Thunderstorms (TSB(hh)mmE(hh)mm) … 92 13.31. Thunderstorm Location (TS_LOC_(MOV_DIR)) … 92 13.32. Hailstone Size (GR_[size]) … 93 13.33. Virga (VIRGA_(DIR)) … 93 13.34. Variable Ceiling Height (CIG_hnhnhnVhxhxhx) … 93 13.35. Obscuration (w’w’_[NsNsNs]hshshs) … 93 13.36. Variable Sky Condition (NsNsNs(hshshs)_V_NsNsNs) … 93 13.37. Significant Cloud Type [PLAIN LANGUAGE] … 94 13.38. Ceiling Height at Second Location (CIG_hhh_[LOC]) (Automated Only) … 94 13.39. Pressure Rising or Falling Rapidly (PRESRR or PRESFR) (Automated Only) … 95 13.40. Sea-Level Pressure (SLPppp) (Automated Only) … 95 13.41. Aircraft Mishap (ACFT_MSHP) … 95 13.42.
Snow Increasing Rapidly (SNINCR_(inches-hour/inches on ground) … 95 13.43. Other Significant Information … 95 13.44. Additive and Automated Maintenance Data … 95 13.45. Precipitation Additive Data … 95 13.46. Hourly Precipitation Amount (Prrrr) (Automated Only) … 96 13.47. 1, 3, and 6 Hourly Ice Accretion Amounts (I1nnn, I3nnn, I6nnn) (Automated Only). .96 13.48. 3- and 6- Hour Precipitation Amount (6RRRR) (Automated Only) … 97 13.49. 24-Hour Precipitation Amount (7R24 R24 R24 R24) (Automated Only) … 97 13.50. Snow Depth on Ground (4/sss) (Sites listed in Appendix F) … 98 13.51. Water Equivalent of Snow on Ground (933RRR) (Sites Listed in Appendix F) … 98 13.52. Hourly Temperature and Dew Point (TsnT’T’T’snT’dT’dT’d) (Automated Only) … 98 13.53. 6-Hourly Maximum Temperature (1snTxTxTx) (Automated Only) … 98 13.54. 6-Hourly Minimum Temperature (2snTnTnTn) (Automated Only) … 99 13.55. 24-Hour Maximum and Minimum Temperature (4snTxTxTxsnTnTnTn) (Automated Only) … 99 13.56. 3-Hourly Pressure Tendency (5appp) (Automated Only) … 99 13.57. Sensor Status Indicators … 100 13.58.
Maintenance Indicator … 100
Chapter 14. Entries on Observational Forms … 101
14.1. Introduction … 101 14.2. Entries on Meteorological Form 1M-10C (MF1M-10C) … 101 14.3. Writing Instrument … 101 14.4. Parenthetical Data … 101 14.5. Missing Data … 101 14.6. Late Observations … 101 14.7. Corrections … 101 14.8. Heading on Form MF1M-10C at LAWRS … 102 14.9. Heading on Form MF1M-10C at Other Stations (NA LAWRS) … 102
vii
14.10. Entries on Form MF1M-10C by Columns … 102 14.11. Additional Instructions for Part-Time Stations … 110 14.12. Additive Data Groups (Not Applicable) … 110 14.13. Tailoring MF1M-10C, Synoptic Data, and Summary of the Day (Not Applicable) ... 110 14.14. Notice of Corrections to Weather Records … 111
Appendices
Appendix A. Abbreviations and Acronyms … 113
Appendix B. Mike-in-Hand … 120
Appendix C. Limited Aviation Weather Reporting Station (LAWRS) Requirements ... 121
Appendix D. Service Standards … 127
Appendix E. METAR User Aids … 130
Appendix F. General Requirements for Measuring Snow Depth … 140
Appendix G. Glossary … 144
Appendix H. Automated Weather System Operation and Broadcast … 155
Appendix I. Aviation Weather Observation Quality Control … 156
Appendix J. Aviation Weather Observer Certification Process … 159
List of Tables
Table 3-1: Content of METAR … 17 Table 3-2: Remarks Section of Observation … 20 Table 5-1: Summary of FAA Augmentation Requirements … 33 Table 5-2: Examples of Augmented Observations … 35 Table 6-1: Summary of Long-line Backup Requirements … 37 Table 6-2: Backup and Augmentation Weather and Obscurations … 41 Table 6-3: Automated System without SPECI Capability Backup Observation Examples … 43 Table 6-4: Automated System with SPECI Capability Backup Observation Examples … 43 Table 7-1: Estimating Wind Speed … 47 Table 8-1: Reportable Visibility Values … 50 Table 9-1: Present Weather … 57 Table 9-2: Estimating Intensity of Rain … 59 Table 9-3: Estimating Intensity of Ice Pellets … 60 Table 9-4: Intensity of Rain or Ice Pellets Based on Rate of Fall … 60 Table 9-5: Intensity of Snow or Drizzle Based on Visibility … 60 Table 9-6: Precipitation Intensity Symbols … 60 Table 9-7: Units of Measure for Precipitation … 62 Table 9-8: Type and Frequency of Lightning … 64 Table 10-1: Reporting Contractions for Sky Cover … 69 Table 10-2: Priority for Reporting Layers … 69 Table 10-3: Examples: Summation of Sky Cover … 70 Table 10-4: Increments of Reportable Values for Layer or Ceiling Heights … 71
viii
Table 10-5: Criteria for Variable Ceiling … 73 Table 12-1: Units of Measure of Pressure Parameters … 77 Table 13-1: Content of METAR/SPECI … 79 Table 13-2: METAR or SPECI Code Format … 79 Table 13-3: Reporting Visibility Values … 82 Table 13-4: Present Weather … 86 Table 13-5: Reportable Values for Sky Cover Amount … 87 Table 13-6: Increments of Reportable Values of Sky Cover Height … 87 Table 13-7: Type and Frequency of Lightning … 91 Table 13-8: Units of Measure for Precipitation … 96 Table 13-9: Characteristics of Barometer Tendency … 99 Table C-1: LAWRS Requirements for Body of METAR … 123 Table C-2: LAWRS Requirements for Remarks Section … 124 Table C-3: LAWRS Requirements for SPECIs … 125 Table D-1: Service Standard Levels … 129
Order_JO_7900.5E › Chapter 1. Introduction
Chapter 1. Introduction
1.1. Purpose of This Order. This order prescribes aviation surface weather observing procedures and practices. This order includes practices and procedures for both manual and automated observation locations. Also included are practices and procedures for augmentation of automated observations and backup information in the event of system failure, erroneous or non-representative data. These procedures and practices are intended to provide a framework for identifying meteorological phenomena of importance to aviation and reporting their occurrence.
1.2. Audience. This order applies to all FAA and FAA-contract personnel, Limited Aviation Weather Reporting Stations (LAWRS) personnel, Non-Federal Observation (NF-OBS) Program personnel, as well as United States Coast Guard (USCG) personnel, as a component of the Department of Homeland Security and engaged in taking and reporting aviation surface observations.
1.3. Where to Find This Order. This order is available on the FAA Web site at http://faa.gov/air_traffic/publications and http://employees.faa.gov/tools_resources/orders_notices/.
1.4. Cancellation. This order cancels FAA Order 7900.5D, Surface Weather Observing, effective December 20, 2016.
1.5. Explanation of Changes. This order has been revised to incorporate the changes implemented with NOTICE JO 7900.11, GS/GR Contraction Change. The organizational change from District Manager to General Manager has been incorporated. Obsolete and redundant paragraphs with information that was provided elsewhere in the order or in another FAA directive have been deleted. (e.g. Types and Content of METAR/SPECI have been removed from Chapter 2 since the information is also in Chapter 3)
Paragraph 4.4 prohibits all weather observers from appending Notice to Airmen (NOTAM) to the AWOS/ASOS broadcast.
Backup procedures for ASOS/AWOS-C OID/OT and communication line failures have been revised in paragraphs 6.3g and 6.4, since both systems have the capability to interface with several other automated systems.
Paragraph 6.13 has been added requiring weather observation stations to develop or include in their existing contingency plan, shutdown procedures of their weather-observing duties.
The Chapter for Runway Visual Range (RVR) reporting has been deleted since RVR reporting is completely automated and when the automated RVR interface fails, the RVR readings are not backed up by weather observers. This information has been added to the Visibility chapter.
The Chapter for Operation of Equipment has been deleted. Equipment used by weather observers is installed and maintained by the National Weather Service (NWS) or FAA Technical Operations. The procedures for observers and the equipment used is contained in other chapters.
The Appendix (Index) has been deleted since the order is only distributed electronically.
Appendix I (Aviation Weather Observation Quality Control), I.3 b. has been deleted. Contacting Regional Operations Center (ROC) is no longer a requirement.
Appendix J (Aviation Weather Observer Certification Process), J.9 Transfers has been revised to assist facilities in transferring certifications from one facility to another.
Appendix B Mike-in-Hand is a supplemental service provided by surface weather observers in Alaska. A new Appendix has been added defining Mike-in-Hand services and requirements.
The old Appendix B, Continuity of Service has been removed. Backup procedures for equipment failures are prescribed in Chapter 6. The need for 24-hour notifications through ROC have not been proven to be necessary.
Weather observers are no longer permitted to disable automated sensors without instructions from maintenance personnel.
SPECI criteria has been updated to inform Air Traffic Control Towers (ATCT) of the ability to add site-specific SPECI criteria. The use of “SKC” versus “CLR” has been clarified.
Standalone Weather Sensor System (SAWS) and Surface Weather System (SWS) have been added to the order and procedures for backing up the automated weather system temperature and dew point data has been updated. The definition of Hygrothermometers has been deleted since the equipment is no longer used.
Non-Federal Weather Observers (NF-OBS) currency requirements have been revised to match those of the former Supplemental Aviation Weather Reporting Stations (SAWRS) since both types of facilities are similar in their duties and responsibilities.
Altimeter equipment and comparison checks are removed from the Appendix C, LAWRS. FAA JO 7210.3, Chapter 2, Section 10 provides guidance on the use of altimeter equipment.
1.6. Abbreviations and Acronyms. Appendix A. Abbreviations and Acronyms, contains abbreviations and acronyms used in this order.
1.7. Relationship to FMH-1 and Other Documents
a. Federal Meteorological Handbook No. 1, Surface Weather Observations and Reports (FMH-1). FMH-1 defines surface weather observing standards for all Federal agencies engaged in taking and reporting surface aviation observations. FMH-1 also defines the standard reporting and coding procedures used in surface aviation observation. Order 7900.5D defines the procedures and practices to be followed by FAA, FAA-contract, and NF-OBS personnel for observing, reporting, and coding surface observations that meet the Federal standards. A description of the NF-OBS Program is provided in FAA JO 7210.77, Non-Federal Weather Observation Program Operation and Administration. This order complements, but does not change the standards contained in FMH-1.
b. Automated Weather Observing Systems Handbooks. Handbooks are produced by automated systems manufacturers. However, all systems must be operated in accordance with
practices and procedures contained in this order. A partial listing of the applicable handbooks necessary to operate the various automated weather observing systems includes:
(1) Federal Aviation Administration, Operator Instructions, Automated Weather
Observing System (AWOS), August 1, 1994, U.S. Department of Transportation, Washington, DC.
(2) National Weather Service ASOS Ready Reference Guide (RSM1005-00038).
1.8. Applicability of Procedures and Practices
a. Applicability. The procedures and practices in this order apply to all facilities that have the equipment capability to comply with the stated procedure or practice. Observers are not required to back up an automated sensor if backup equipment is not available. Procedures for coding missing data are contained in Paragraph 6.5 and throughout this order.
b. Conflicting Information. In case of conflicting information, the procedures and practices in this order take precedence. However, any applicable FAA air traffic orders take precedence over any procedures or practices in this order that are in conflict. Such conflicts should be brought to the attention of the originator of this order.
c. Terminology. Throughout this order, the following terminology applies:
(1) Must – indicates a procedure or practice that is mandatory at all applicable
facilities.
(2) Should – indicates a procedure or practice that is recommended at all applicable
facilities.
(3) May – indicates a procedure or practice that is optional.
(4) Will – indicates futurity; it is not a requirement to be applied to current practices.
d. Unforeseen Requirements. No set of procedures and practices can cover all possibilities in weather observing. The observer must use good judgment, adhering as closely as possible to this order, to describe phenomena not adequately covered by cover such situations may be made through appropriate channels.
1.9. User Responsibilities. Employee participation in directive writing and upkeep activities is encouraged. Any user who finds a subject matter conflict, an error, obsolete information, or who would like to make recommendations or suggestions should notify Air Traffic Services, in writing. FAA Form 1320-19, Directive Feedback Information, is available for this purpose. If clarification or correction is urgently needed, you may call Air Traffic Services for guidance, but you should also use the FAA Form 1320-19 as a follow-up to verbal conversation.
1.10. Distribution. This order is distributed to select offices in Washington Headquarters; Air Traffic Organization; Office of Operations Planning; NAS Weather Office; Flight Standards Service; the Mike Monroney Aeronautical Center; the William J. Hughes Technical Center; the USCG Elizabeth City Facility; the Department of Defense (DoD); all air traffic field facilities; all Alaska flight service stations (FSS); FAA-contract weather; and the National Weather Service (NWS).
1.11. Changing the Order. Changes, additions, deletions, and corrections will be issued as necessary. These changes will be issued by the Director, Air Traffic Services.
1.12. Maintaining the Order. Each facility must maintain a copy of the order, complete with changes and supplements for reference purposes. When inserting changes to the order, enter the number, effective date, initials, and date entered on the inside cover of this order.
Order_JO_7900.5E › Chapter 2. Guidelines
Chapter 2. Guidelines
2.1. Introduction. This chapter describes the types of aviation surface weather observing facilities for which the FAA may have responsibility or oversight. This chapter also describes the various types of surface weather reports, including the Aviation Routine Weather Report (METAR) and Aviation Selected Special Weather Report (SPECI), and FAA guidelines regarding the content of each of these types. Also presented are general guidelines regarding augmentation and backup of automated observations. Lastly, this chapter presents FAA guidelines on the certification of observers.
2.2. Types of Stations. The generic types of stations that take aviation weather observations are defined as follows:
a. Automated Station. A facility equipped with an automated surface weather observing system that prepares the observation without a certified observer on duty. The various types of automated stations are described in Chapter 4. Observations generated by automated stations will always be identified by the inclusion of the word AUTO in the transmitted report.
b. Augmented Station. A facility with an automated surface weather observing system that prepares the METAR/SPECI with a certified observer on duty capable of adding operationally significant weather information to the observation. The observer is completely responsible for the observation even though the automated weather observing system generates the report. At facilities where augmentation is not available full time, the facility is classed as automated during the non-augmented periods.
c. Manual Station. A facility where certified weather observers are responsible for observing, evaluating, and preparing the METAR/SPECI without the use of an automated weather observation system (ASOS/AWOS).
2.3. Non-Federal Weather Observation (NF-OBS) Station. A program in which FAA certified, non-Federal observers enter into an agreement with the appropriate FAA Office to provide backup and/or augmentation of the automated system, or provide manual weather observations. NF-OBS observers may include non-Federal control tower (NFCT) controllers, airline personnel, fixed base operator (FBO) personnel, or other entities. At these facilities, various degrees of automated sensors and/or other automated equipment may be available. However, when on duty, the NF-OBS observer must provide backup and/or augmentation in accordance with their NF-OBS agreement. Program establishment is contained in FAA JO 7210.77, Non-Federal Weather Observation Program Operation and Administration.
2.4. General Types of Observations. There are three general types of surface observations:
a. Automated Observation. Any observation, which has been prepared and transmitted by an automated observing system without human intervention.
b. Augmented Observation. Any automated observation, which has been evaluated by a human observer to which additional weather information has been manually added that, is beyond the capabilities of the automated weather observing system and/or is deemed operationally significant. The guidelines concerning augmentation are presented in
Paragraph 2.5, Augmentation Requirements. Backup is a method of providing an observation, part of an observation, documentation, or communication of an observation at selected sites when the primary method is unavailable or non-representative. The guidelines concerning backup information are presented in Paragraph 2.6 Backup Requirements.
NOTE: Backing up a failed automated system (ASOS/AWOS) is not considered a manual observation.
c. Manual Observation. Any observation, for which the human observer observes, evaluates, prepares, records, and transmits the observation without the use of an automated observing system. The guidelines for manual observations are presented in Chapter 3. General Procedures.
2.5. Augmentation Requirements. Certified observers are responsible for the completeness and accuracy of the weather observation. Automated weather observing systems are, by design, viewing a smaller area than a human observer, therefore, the observer is responsible for providing additional information that covers a larger area when operationally significant. Augmentation of automated observations must be provided in accordance with the guidelines presented in the following subsections and as specified for the station’s service level standard (Appendix D, Service Standards). Separate guidelines are presented for the two general types of automated weather observing systems: automated systems with SPECI capability and automated systems without SPECI capability. Procedures and practices to be followed to accomplish the required augmentation are presented in Chapter 4, General Procedures at Automated Weather Stations, and Chapter 5, Augmentation Requirements at Automated Weather Stations.
a. Facilities with an Automated System with SPECI Capability.
(1) ATCT with a Surface-Based Observer. At facilities with an ATCT, and an automated system with SPECI capability, and with a surface-based observer on duty, the surface-based observer must provide augmentation of the automated observation. This augmentation must include, but not be limited to the requirements contained in Service Standards for that level of airport (see Appendix D. Service Standards). At these facilities, the ATCT must routinely provide tower visibility when applicable.
(2) All other facilities with an Automated System with SPECI Capability. At facilities with an ATCT, and an automated system with SPECI capability, but without a surface-based observer on duty, the tower observer must provide augmentation of the automated observation. At facilities with surface based observers, augmentation will be the responsibility of the collocated FSS (Alaska only) or other weather observers. This augmentation must include, but not be limited to:
(a) Thunderstorm.
(b) Tornadic activity (including tornado, waterspout, and funnel cloud).
(c) Hail.
(d) Virga.
(e) Volcanic ash.
(f) Any weather elements considered operationally significant by the observer.
b. Facilities with an Automated System without SPECI Capability. At these facilities, the observation is the responsibility of the surface-based observer, if one exists. At towered sites without a surface-based observer, the observation is the responsibility of the LAWRS observer.
REFERENCE: FAAO JO 7210.3, Para 2-9-2d, Receipt and Dissemination of Weather Observations
2.6. Backup Requirements
a. Situations Requiring Backup. Backup refers to the observer providing the same reporting capability as that provided by the automated weather sensor, consistent with service level standards specified in Appendix D Service Standards. Backup information is required for long-line dissemination for terminal forecast (TAF) production and for local, ground-to-air dissemination to legally sustain local operations at the airport.
(1) Sensor/system Malfunction. One or more sensors or the entire observing system is (are) not reporting data (for any reason). Provide backup using readings from FAA approved backup equipment (if available) and make appropriate maintenance notifications.
(2) Communications Failure (Service A Outage). The automated weather observing system and/or long-line communications are malfunctioning, thereby preventing the entry and/or transmission of the observation over long-line networks.
(a) At manual Automatic Terminal Information Service (ATIS) locations or uncontrolled airports, when it is apparent that observations are not being transmitted, the required information must be relayed to the overlying Air Route Traffic Control Center (ARTCC) Flight Data unit for entry into an FAA approved electronic system (for example, Aeronautical Information System Replacement (AIS-R), System Wide Information Management (SWIM) or similar systems) or, in Alaska, phoned to the tie-in Flight Service Station. Notify the appropriate office of the outage.
(b) At digital ATIS locations, the weather observer must first coordinate and receive approval from the air traffic control tower prior to disseminating reports via the alternate methods (e.g., AIS-R, SWIM, relaying to the ARTCC Flight Data unit). The observer must also ensure that any weather reports entered via alternate methods are promptly relayed to the tower for the ATIS broadcast.
b. Non-representative Data. The sensor is reporting data, but the data is incorrect or the sky condition, visibility, and/or present weather sensor(s) is/are accurately reporting conditions in the vicinity of the sensor, but those conditions are not representative of prevailing conditions for the operating areas of the airport and are considered operationally significant. When this occurs, provide backup using readings from FAA approved backup equipment and/or visibility charts. Outage notification is not required.
c. LAWRS ATCTs and FSS’s. Certified air traffic control specialists (ATCS) must provide the backup information for long-line transmission that is listed in this section. The required information must be entered into the automated systems with SPECI capability via the operator interface device. At locations with automated systems without SPECI capability, the required information must be relayed to the overlying ARTCCs Flight Data unit for entry into an FAA approved electronic system (for example, AIS-R, SWIM or similar systems) or, in Alaska, phoned to the tie-in Flight Service Station. The following information must be provided at a minimum:
(1) Wind.
(2) Visibility to 10 miles.
(3) Present weather and obstructions to vision (see Table 6-2 for required
elements).
(4) Sky condition to 12,000 feet.
(5) Temperature/Dew Point.
(6) Altimeter Setting.
(7) Required remarks and operationally significant remarks as deemed appropriate.
d. ATCTs with a Surface-Based Observer. At locations with a surface-based observer, the surface-based observer must provide, at a minimum, the backup information for long-line transmission according to the requirements contained in the Service Standards for the service level of the airport.
e. Non-towered Stations with a Surface-Based Observer. At all non-towered stations, the surface-based observer must provide the backup information required by the Service Standards for the service level of the airport.
2.7. Evaluating Weather Sensor Accuracy. When the observer has reason to believe that the accuracy or validity of indications from meteorological sensors is questionable, the use of such equipment should be discontinued until necessary corrective maintenance has been completed. If the use of such equipment is a sensor is discontinued, readings from FAA approved backup equipment must be used, and required backup procedures or practices must be initiated. FAA personnel and NF-OBS sponsors must disseminate appropriate maintenance notifications in the event of any equipment outages.
a. Network Enterprise Management Center (NEMC). If the observer believes that the Federal or non-Federal AWOS information is inaccurate requires maintenance, contact the Network Enterprise Management Center (NEMC) NEMC at 1-855-FAA-NEMC (322-6362). FAA Technical Operations is responsible for issuing NOTAMs on AWOS.
b. ASOS Operations and Monitoring Center (AOMC). If the observer believes that the ASOS information is inaccurate, requires maintenance, they should notify the AOMC at 1-800- 242-8194 OR 8895. The National Weather Service is responsible for issuing NOTAMs on ASOS.
Order_JO_7900.5E › Chapter 3. General Procedures
Chapter 3. General Procedures
3.1. Introduction. This chapter prescribes procedures and practices applicable to all facilities and to all types of observations. These general procedures also apply to observations taken to fulfill requirements for augmentation or minimum operational requirements during backup. This chapter also describes the various types of surface observations and prescribes the criteria for taking SPECI observations.
3.2. Certification of Personnel and Currency Requirements. Before assuming full responsibility for taking any type of surface observation or any part thereof, each person must be certified in accordance with Appendix J of this order. The FAA is responsible for certifying all aviation weather observers at FAA sponsored stations, in one or more of the following observer types.
a. FAA contract weather observers.
b. LAWRS observers.
c. NF-OBS observers.
d. Tower visibility observer is certified by the FAA through eLMS.
NOTE: Currency requirements are defined in FAA Order JO 3120.4, Air Traffic Technical Training and Appendix J of this order.
3.3. Definitions.
a. Actual Time of Observation. The actual time of observation is the time the last element of the observation is observed or evaluated. The actual time of a SPECI must be the time the criteria for the SPECI were met or noted.
b. Aircraft Mishap. Aircraft mishap is an inclusive term to denote the occurrence of an aircraft accident or incident.
c. Aviation Routine Weather Report (METAR). A METAR is a measurement or evaluation of meteorological elements that describe the state of the atmosphere at the surface location(s) where the observation is taken. METAR is a scheduled observation. The METAR is the primary observation code used in the United States to satisfy requirements for reporting surface meteorological data. It contains a report of wind, visibility, RVR (where connected), weather, sky condition, temperature, dew point, and altimeter setting (collectively referred to as "the body of the report"). In addition, coded plain language information that elaborates on the data in the body of the report may be appended to the METAR or SPECI. This significant information is referred to as "remarks." At Manual Observations and augmented stations, the METAR may be abridged to include one or more of the above elements. The contents of METAR observations are given in Table 3-1. METAR observations that also meet the criteria for a SPECI observation are called METAR observations.
d. Aviation Selected Special Weather Report (SPECI). A SPECI is a weather observation that is reported at other than a scheduled time. SPECI must be taken when any of the criteria for a special observation is observed or detected. A SPECI observation is an unscheduled observation taken when any of the criteria given in Paragraph 3.11, Criteria for SPECI Observations, have been observed. A SPECI observation must contain the elements in a METAR (Table 3-1, Table 3-2), plus additional coded or plain language information that elaborates on the data in the body of the report. The SPECI criteria are applicable only to stations that have the capability of evaluating the event. All SPECI must be taken as soon as possible after relevant criteria are observed.
e. Weather Watch. Observers must monitor weather conditions via a weather watch. Two types of weather watch are possible: a Basic Weather Watch and a Continuous Weather Watch. All FAA, FAA-contract, and NF-OBS observers including LAWRS must monitor weather conditions via a Basic Weather Watch as described below.
f. Basic Weather Watch. During a Basic Weather Watch, the observer may be required to perform other duties as their observing workload permits. Because of this and other restrictions (station location, structural design, etc.) that may limit the observer’s capability to continuously view and evaluate weather conditions, observers performing a Basic Weather Watch cannot be expected to detect and report all weather changes as they occur. In addition to taking and disseminating required observations, facilities performing a Basic Weather Watch must recheck weather conditions to determine if a new observation (SPECI) is required when advised by any reliable source (for example, tower controller) that existing conditions differ from those reported in the last disseminated observation.
g. Continuous Weather Watch. On a Continuous Weather Watch, the observer must monitor weather conditions on a continuous basis. In addition to METAR observations, observers must take and disseminate observations as conditions meeting criteria for SPECI observations occur.
h. Observer. The generic term "observer" applies to a number of different types of personnel with various responsibilities for providing weather information. These various types are:
(1) Weather Observer. FAA, FAA-contract personnel, and non-Federal personnel who are certified by the FAA to provide a designated range of weather observation elements.
i. LAWRS Observer. An FAA certified ATCS with weather observation responsibilities.
ii. Tower Visibility Observer. An FAA-certified ATCS with tower visibility responsibilities from the control tower.
(2) NF-OBS Observer. A non-Federal observer certified by the FAA, working under the guidelines of the NF-OBS Program, providing backup and/or augmentation of the automated system with SPECI capability.
(3) DoD Aeronautical Meteorological Observer. A non- FAA aeronautical meteorological observer trained and certified by their respective DoD Service that works under the Service's regulations and provides backup and or augmentation of the automated systems with SPECI capability at airfields where the DoD has the responsibility to provide surface weather observations.
3.4. Aviation Weather Observing Locations. Surface weather observation locations must make routine reports at fixed intervals (METAR reports). Where the capability exists, the routine reports must be supplemented by non-routine reports (SPECI). The usual point of observation is defined as the point or points at which the various elements are observed. Normally, multiple observing points are confined to an area within about 2 miles of the station.
a. For elements such as clouds, prevailing visibility, present weather, and obscurations, the observing location may be coincident with the observer’s physical location or it may be the touchdown area of the primary runway.
b. For temperature, dew point, and wind, the observing location may be the center of the runway complex.
c. For cloud height and ceiling, the observing location may be a point near the approach end of a runway.
d. For the location of lightning, the observing point may be the Airport Reference Point (ARP). The ARP is a permanent airport reference point defined by a latitude/longitude.
e. For tower visibility, the observing location must be the airport traffic control tower (ATCT). (NA LAWRS)
3.5. General Observing Practices. The general observing practices specified in the following subsections apply to personnel taking either full manual, augmented, backup, or tower visibility observations. They do not necessarily apply to the automated portions of observations, which are controlled by system software. Observers must be alert to situations conducive to significant changes in weather conditions and must take and disseminate SPECI observations as rapidly as feasible whenever changes are noted that meet the criteria specified in Paragraph 3.11, Criteria for SPECI Observations.
a. Order of Observing. Elements having the greatest rate of change must be evaluated last. When conditions are relatively unchanging, the observer must evaluate the elements outdoors first, and then evaluate the elements indoors, with pressure being the last element evaluated.
b. Recency of Observed Elements. Individual elements entered in an observation must, as closely as possible, reflect conditions existing at the actual time of observation. At manual locations, elements entered must have been observed within 15 minutes of the actual time of observation. Gusts and squalls must be reported if observed within 10 minutes of the actual time of observation. METAR observations must be made as close to the scheduled time as possible to meet filing deadlines, but in no case will these observations be started more than 15 minutes before the scheduled time.
c. Dark Adaptation. When taking observations outdoors at night, sufficient time should be allowed for the observer’s eyes to become adjusted to the darkness.
d. Weather Not Observed. Observers are not required to report occurrences they have not observed. However, the observer may use information from reliable sources, for example, pilots, airline/airport personnel, a commissioned AWOS or other sources deemed acceptable by the observer. Weather Observers must not use the internet or other electronic systems not specifically approved by the FAA.
e. Time Disseminated in Reports. All times must refer to the 24-hour clock, for example, 1:47 a.m. must be referred to as 0147; 1:47 p.m. must be referred to as 1347. The times 0000 and 2359 must be used to indicate the beginning and ending of the day, respectively.
f. Time Standards. Times used in weather observations must be:
(1) Local Standard Time (LST). (NA LAWRS). LST is used on MF1M-10Cs to record times of observation and time checks. LST must be entered on all forms throughout the year with no consideration of daylight savings time.
(2) Coordinated Universal Time (UTC). UTC is used on all transmitted data. It is also used on MF1M-10Cs to record times of observations and time checks at LAWRS sites.
(3) METAR REPORTS. Prepare and code METAR reports for transmission between H+55 and H+00.
(4) SPECI AND DELAYED OR CORRECTED REPORTS. Transmit SPECI, delayed or corrected reports as soon as possible after H+00.
g. Accuracy of Time in Observations. The accuracy of the actual time of observation is very important in aviation safety investigations. One clock must be designated as the observing location standard, and a routine procedure set up to assure its accuracy once a day at a minimum. The clock used must be within ± 1 minute of the U.S. Naval Observatory Time. If available, the FAA Coded Time Source (CTS) may be substituted for U.S. Naval Observatory Time.
h. SPECI Observations upon Resumption of Observing Function. Observers must take, record, and disseminate a SPECI observation within 15 minutes after returning to duty following a break in normally scheduled observer coverage at the station unless a METAR observation is filed during that 15-minute period.
3.6. Dissemination. For purposes of this order, dissemination is the act of delivering a completed report to users.
a. Local. Local transmission is the transmission or delivery of a weather report to individuals or groups of users in the service area of the observing location. All reports must be given local dissemination.
b. Long-line (Service A Circuit). Long-line transmission is the transmission of a weather report beyond the service area of the observing location. At stations with long-line capabilities, reports must be given long-line dissemination.
c. If reports cannot be disseminated simultaneously, local and long-line, they must be disseminated first to the local airport traffic control users, then disseminated long-line.
d. When reports are corrected, the corrected report must be given the same dissemination as the report being corrected.
e. SPECI observations must be completed and transmitted as soon as possible after conditions meeting SPECI criteria are observed or detected.
f. A METAR entered that also meets the criteria for a SPECI must be disseminated as a METAR.
3.7. Corrections to Transmitted Data. Once an error has been detected in a transmitted report, a correction must be transmitted as soon as possible.
a. Do not transmit a correction if the original transmitted observation has been superseded by a later report.
b. Transmit the entire corrected report with (COR) as the report designator. Use the original date and time of the report being corrected.
c. The COR function is used for mistyped/misspelled entries and must not be used as a means of augmenting/editing the automated weather observation system. If a valid weather observation has transmitted and operationally significant weather conditions or SPECI criteria exist, the weather observer should generate a new observation with current sensor data.
NOTE: When a COR is issued, if the ASOS/AWOS-C is set to broadcast the Last Transmitted Observation (LTO), the telephone broadcast will be unavailable until the next METAR/SPECI is issued. If the ASOS/AWOS-C is set to broadcast the One-Minute Observation (OMO), the telephone broadcast is not affected.
3.8. Delayed Reports (Manual Stations Only). When transmission of a manual observation is delayed until time for the next regularly scheduled report, only the latest report must be transmitted. In the record of observations, the remark Filed but Impractical to Transmit (FIBI) must be appended in parentheses to the report that was not transmitted. The remark FIBI must not be included in any local dissemination of the report. When a SPECI is not transmitted long- line, later SPECIs must be transmitted long-line only when the overall change between the last transmitted report and the current report satisfies the criteria for a SPECI. If the SPECI is not transmitted long-line, the remark FIBI must be appended to the report as described above. All SPECI reports must be disseminated locally. Reports of volcanic eruption must be disseminated, by any means possible, regardless of the delay.
c. › Runway Visual Range (NA LAWRS).
07/1/2021 JO 7900.5E, Chg 1
3.9 Rounding Off Numbers. Except where otherwise designated in this order, when computations require that a number be rounded, if the fractional part of a positive number to be dropped is equal to or greater than one-half, the preceding digit must be increased by one. If the fractional part of a negative number to be dropped is greater than one-half, the preceding digit must be decreased by one. In all other cases, the preceding digit must remain unchanged. For example, 1.5 becomes 2, 1.3 becomes 1, -1.5 becomes -1, and -2.6 becomes -3.
3.10 RecordKeepingandForms
a. Manual Observations. All manual observations at manual stations, whether complete or partial, must be recorded on the electronic version of form MF1M-10C (does not include automated/augmented stations). The form is available from the NWS at https://www.weather.gov/surface/forms. After completing the form, it must be archived at the facility for 90 days. Manual Stations must send the electronic form to the National Center for Environmental Information (NCEI) at [email protected] by the second working day of each month. Corrected copies of all forms must be retained locally for 90 days. Retention of copies beyond 90 days must be as directed by the FAA.
b. Automated Weather Observations. Automated weather observations and operator terminal entries are archived on site. No further action is required by FAA, FAA-contract, or NF OBS facilities. In the event of a complete failure of automated equipment, observers are expected to follow manual observation reporting requirements. The MF1M-10C is not required.
3.11 Criteria for SPECI Observations. The observer must take, record, and disseminate a SPECI observation when any of the following is observed tooccur:
a. Wind Shift. Wind direction changes by 45 degrees or more in less than 15 minutes, and the wind speed is 10 knots or more throughout the wind shift.
b. Visibility. Visibility as reported in the body of the report decreases to less than, or if below, increases to equal or exceed:
(1) 3 miles.
(2) 2 miles.
(3) 1 mile.
(4) 1/2 mile.
(5) 1/4 mile.
(6) The lowest standard instrument approach procedure minimum as published in the U.S. Terminal Procedures. If not listed above.
c. Runway Visual Range (NA LAWRS). The highest value from the designated RVR runway decreases to less than, or if below, increases to equal or exceed 2,400 feet during the preceding 10 minutes.
3.10 RecordKeepingandForms › 16
07/1/2021 JO 7900.5E, Chg 1
d. Tornado, Funnel Cloud, or Waterspout.
(1) Is observed.
(2) Disappears from sight or ends.
e. Thunderstorm.
(1) Begins (a SPECI report is not required to report the beginning of a new thunderstorm
if one is currently reported).
(2) Ends.
f. Precipitation.
(1) Hail (including small hail) begins or ends.
(2) Freezing precipitation begins, ends, or changes intensity.
(3) Ice pellets begin, end, or change intensity.
(4) Snow begins, ends, or changes intensity.
g. Squall. Wind speed suddenly increases by at least 16 knots and is sustained at 22 knots or more for at least one minute.
h. Ceiling. The height of the base of clouds covering five eighths or more (for example, broken and overcast) of the sky forms or dissipates below, decreases to less than or, if below, increases to equal or exceed:
(1) 3,000 feet.
(2) 1,500 feet.
(3) 1,000 feet.
(4) 500 feet.
(5) The lowest standard instrument approach procedure minimum as published in the U.S. Terminal Procedures. If none published, use 200 feet.
i. Sky Condition. A layer of clouds or obscuring phenomenon aloft is present below 1,000 feet and no layer aloft was reported below 1,000 feet in the preceding METAR or SPECI observation.
j. Volcanic Eruption. When eruption is first noted.
k. Aircraft Mishap. Upon notification of an aircraft mishap, unless there has been an intervening observation.
Report Modifier COR › X
07/1/2021 JO 7900.5E, Chg 1
l. Miscellaneous. Any other meteorological situation that, in the opinion of the observer, is critical. The local Air Traffic Control facility may also develop site-specific criteria for issuing a SPECI (e.g. additional ceiling criteria, Layers below criteria, Visibility criteria, RVR).Site-specific SPECI criteria can be added to automated weather system by the ASOS/AWOS-C system manager or implemented by the weather observer.
3.12 Content of METAR/SPECI Observations. Table 3-1contains the content of METAR observations. The first column of the table lists the elements of the observation both for the body of the report and the remarks section. The second column lists a reference to the section in 13 that discusses coding of the particular element. The third column presents a brief description of the element. The fourth column indicates whether the element is reported in METAR observations, and the fifth column indicates whether the element is reported in SPECI observations.
Body of METAR Consists of 11 Elements
Element Paragraph Brief Description METAR SPECI
Type of Report (METAR/SPECI)
13.6 METAR is the routine (scheduled) report. SPECI is the
non-routine (unscheduled)
weather report.
X X
Station Identifier
(CCCC)
13.7 ICAO station identifier. Consists of four alphabetic characters, for
example, KABC.
X X
Date/Time (YYGGggZ)
13.8 Day of the month, followed by the
actual time of the report or when the criteria for a SPECI is met or
noted. Group ends with Z to
indicate UTC. For example,
X X
Report Modifier
(AUTO)
13.9 AUTO indicates a fully automated
report. If not automated report,
this field is blank.
X X
Report Modifier
COR
13.9 COR indicates the report is a correction of a previously issued
METAR or SPECI
X X
Present Weather (w'w') › X
07/1/2021 JO 7900.5E, Chg 1
Body of METAR - Consists of 11 Elements
Element
Wind (dddff(f)Gfmfmfm
KT) (dndndnVdxdxdx)
Visibility (VVVVVSM)
Runway Visual
Range (RDRDR/VRVRVRVRF
T Or RDRDR/VNVNVNVNVV
X VXV XVXFT)
Automated Only Do Not
Back Up
Paragraph
13.10
13.11
13.12
Brief Description
True wind direction in tens of degrees using three digits. Speed
reported in whole knots (two or three digits). Gusts (G) appended to
the speed, if observed. Group ends with KT, for example, 23018G26KT.
If wind direction varies by 60° or
more and speed is >6 knots, a variable wind group may also be reported, for example, 180V250.
Direction may be reported VRB (variable) if speed is <6 knots or
less. For example, VRB05KT. Calm winds are coded 00000KT.
Prevailing visibility in statute miles. A space divides whole miles and fractions. Ends with
SM: 1 1/2SM. AUTO: M pref.
means "less than": M1/4SM.
The 10-minute RVR value: Reported in hundreds of feet if visibility is < one statute mile or RVR is < 6000 feet. Group ends
with FT to indicate feet, for example, R06L/2000FT. Prefixed
with either M or P indicates the value is lower or higher than the
RVR reportable values, for example, R06L/P6000FT. If variable during the evaluation period, the variability is reported, for
example, R06L/2000V4000FT.
METAR
X
X
A/B
SPECI
X
X
A/B
Present Weather
(w'w')
13.13 Weather phenomena (other than
obscurations) occurring at the station are reported in the body of
the report. Weather obscurations are generally reported if visibility < 7 miles (see 14-14 for exceptions). Volcanic ash may be reported with
any visibility. Reported in order of
decreasing predominance.
Maximum of three groups reported (pcpn included in one group; separate groups for other
phenomena).
X X
Altimeter (APHPHPHPH) › X
07/1/2021 JO 7900.5E, Chg 1
Body of METAR - Consists of 11 Elements
Element
Sky Condition (NsNsNshshshs or VVhshshs or CLR
or SKC)
Temperature/De
w Point (T'T'/T'dT'd)
Paragraph
13.14
13.15
Brief Description
Automated stations report no
more than three layers up to
12,000 feet; if no layers are detected, CLR is reported. At manual stations, up to six layers
may be reported; if no layers observed, SKC is reported. Each layer contains the amount (FEW,
SCT, BKN, OVC) immediately followed by the height using three
digits, for example, FEW015, BKN030. A layer containing CB or
TCU is indicated by appending the contraction to the layer height,
for example, FEW015TCU. All layers are considered opaque. Vertical Visibility (VV) is reported
in hundreds of feet for a total obscuration (indefinite ceiling), for
example, VV002. Surface-based
obscuration (manual only) reported using amount (FEW, SCT, BKN) followed by "000," for
example,SCT000; remark reported as "FG SCT000".
Temperature and dew point are
reported to the nearest whole degree Celsius using two digits,
for example, 17/13. Sub-zero values are prefixed with an M, for
example, 03/M02.
METAR
X
X
SPECI
X
X
Altimeter (APHPHPHPH)
13.16 Altimeter is prefixed with an A indicating altimeter in inches of
mercury.
Reported using four digits; tens,
units, tenths, and hundredths of inches of mercury, for example,
A2990.
X X
Peak Wind (PK WND dddff(f)/(hh)mm) Automated Remark Only Do Not Back Up › X
07/1/2021 JO 7900.5E, Chg 1
Remarks Section of Observation
Element
Volcanic Eruptions
Tornadic Activity
(Manual and Augmented Auto)
(Tornadic activity_B/E(hh)mm
LOC/DIR_(MOV))
Type of Automated Station (AO1, AO2)
Automated Remark
Only Do Not Back Up
Paragraph
13.19
13.20
13.21
Brief Description
Volcanic eruptions must be reported
whenever first noted. Pre-eruption activity must not be reported. (Use PIREPs to report pre-eruption activity.) Encode volcanic eruptions as described
in Chapter 14.
Whenever tornadoes, funnel clouds, or waterspouts begin, are in progress, end, or disappear from sight, the event should
be described directly after the "RMK" element. This remark must give, insofar
as known, the phenomena, time, location and direction from the station,
and direction of movement. The time
the tornadic activity began must be reported and prefixed with a "B," the
time the tornadic activity ended or disappeared from sight must be reported
and prefixed with an "E," for example,
TORNADO B13 DSNT NE.
This remark identifies the type of automated station. It must be included in all reports from automated stations. AO1
identifies an automated station without a precipitation discriminator; AO2 identifies
an automated station with a precipitation
discriminator.
METAR
X
X
X
SPECI
X
X
X
Peak Wind (PK WND
dddff(f)/(hh)mm)
Automated Remark
Only Do Not Back Up
13.22
When the peak wind exceeds 25 knots, the remark is included in the
next METAR report. ddd is the direction of the peak wind, ff(f) is the
peak wind speed since the last METAR report, and (hh)mm is the time
of occurrence (with only the minutes
reported if the hour can be inferred from the report time), for example, PK
WND 28045/15.
X
Visibility at Second Location (VIS vv location) Automated Remark Only… › X1
07/1/2021 JO 7900.5E, Chg 1
Element Paragraph Brief Description METAR SPECI
Wind Shift (WSHFT_(hh)mm) 13.23
At stations with automated systems with
SPECI capability and manual stations,
when a wind shift occurs, WSHFT followed by a space and the time the wind shift began must be reported (with
only the minutes reported if the hour can be inferred from the report time).
The contraction FROPA may be entered
following the time if it is reasonably certain that the wind shift was the result of frontal passage, for example, WSHFT
30 FROPA.
X X
Tower or Surface Visibility (TWR VIS) (SFC
VIS)
13.24
If tower visibility or surface visibility is
carried in the remarks, use the appropriate set of values and precede
the visibility with the appropriate identifier, TWR VIS or SFC VIS, for
example, TWR VIS 1.
A/B A/B
Variable Prevailing
Visibility (VIS
minVmax)
13.25
Whenever the prevailing visibility is
less than 3 statute miles and is variable, this remark must be entered
where min is the lowest visibility evaluated and max is the highest visibility evaluated, for example, VIS
1/2V2.
X X
Sector Visibility
(VIS_dd_vv) 13.26
Sector visibility must be reported when it differs from the prevailing visibility by
one or more reportable values and, either the prevailing or sector visibility is
less than 3 miles or considered to be operationally significant. In the remark,
dd defines the sector to 8 points of the compass and vv is the sector visibility in
SM, for example, VIS N 2.
X X
Visibility at Second
Location (VIS vv
location)
Automated Remark
Only Do Not Back Up
13.27
When an automated station uses meteorological discontinuity sensors, remarks must be added to identify site-
specific visibilities, which differ from conditions reported in the body of the
report. vv is the visibility value measured at the secondary location.
This remark must only be generated when the condition is lower than that
contained in the body of the report.
X1 X1
Thunderstorm Location (TS_LOC_(MOV_DIR )) › X
07/1/2021 JO 7900.5E, Chg 1
Element
Lightning (Frequency_LTG(type
) _
[LOC])
Beginning/Ending
Time of Precipitation
(WX)B(mm)E(mm)
(NA LAWRS
Beginning/Ending
Time of Thunderstorms (TS)B(mm)E(mm)
Paragraph
13.28
13.29
13.30
Brief Description
When lightning is manually observed,
the frequency and location must be
reported, along with the type of lightning, if known. For example, OCNL LTG OHD, FRQ LTGCG VC NE. When
lightning is detected by an automated
sensor (e.g. ALDARS) within 5NM of
the ARP, it is reported as "TS" in the body of the report with no remark; within
5-10NM of the ARP, it is reported as "VCTS" in the body of the report with no
remark. Beyond 10NM from the ARP lightning is reported in remarks as "LTG
DSNT" followed by direction from the ARP, for example, OCNL LTG DSNT
NE.
At stations with automated systems with
SPECI capability and Manual Stations,
when precipitation begins or ends, the
next METAR report must include the
type of phenomena, the beginning and/or ending time (prefixed with a B and/or E). If the beginning or ending of
the precipitation type (hail, freezing precipitation, or ice pellets), initiated the
SPECI report, then that SPECI report must include the type of phenomena, the beginning and/or ending time, and should be reported in the next METAR
report.
When thunderstorms begin or end, the
SPECI report must include the type of
phenomena, the beginning and/or ending time (prefixed with a B and/or E), and should also be reported in the
next METAR report, for example,
TSB05E45
METAR
X
X
X
SPECI
X
X
X
Thunderstorm
Location (TS_LOC_(MOV_DIR
))
13.31 Thunderstorm location and movement,
if known, must be encoded. For
example, TS SE MOV NE.
X X
TR › station, for example, TCU W.
07/1/2021 JO 7900.5E, Chg 1
Element Paragraph Brief Description METAR SPECI
Hailstone Size (GR_{INCHES}) 13.32
At augmented automated stations and
at manual stations, the size of the largest hailstone is coded in 1/4 inch
increments, identified with the contraction GR. When small hail less
than 1/4 inch in size is occurring, the hailstone size is reported in remarks as
X X
Virga (VIRGA_{Direction}) 13.33
When precipitation is observed to be falling from clouds, but is not reaching
the ground because of evaporation, report VIRGA; the direction from the station is optional, for example, VIRGA
or VIRGA SW.
X X
Variable Ceiling
Height (CIG
minVmax)
13.34
Whenever the ceiling is below 3,000 feet and is variable, enter min as the lowest ceiling height evaluated and max
as the highest ceiling height evaluated,
for example, CIG 005V010.
X X
Obscurations
sNsNs) hshshs) 13.35
When the sky condition contains an obscuration either, at the surface or
aloft, other than clouds, the type of phenomena in the layer, plus the sky cover at the layer and the height must
be reported in remarks, for example,
FG SCT000 or FU BKN015.
X X
Variable Sky
Condition (NsNsNs(hshshs)_V_Ns
NsNs)
13.36
This remark must identify the layer that
is varying and indicate the range of variability. If there are several layers of
the same coverage, the variable layer must be identified by including the layer
height.
X X
Significant Cloud
Types 13.37
When observed, the following clouds
are reported in remarks: 1.) Cumulonimbus (CB) or Cumulonimbus
Mammatus (CBMAM), distance, direction from the station, direction of
movement, for example, CB W MOV E, CB DSNT W. 2.) Towering Cumulus (TCU), distance, and direction from the
A A
station, for example, TCU W. 3.) Altocumulus Castellanus (ACC), direction from station, for example,
ACC NW. 4.) Standing Lenticular (stratocumulus SCSL; altocumulus ACSL, or cirrocumulus CCSL) or rotor
Aircraft Mishap (ACFT_ MSHP) › X
07/1/2021 JO 7900.5E, Chg 1
Element Paragraph Brief Description METAR SPECI
clouds, direction from the station, for
example, ACSL SW-W, APRNT
ROTOR CLD NE, CCSL S.
Cumulonimbus of any kind and towering cumulus are also identified in
the body of the report.
Ceiling Height at Second Location
(CIG_ {height}_
{LOC})
Automated Remark
Only Do Not Back Up
13.38
When an automated station uses meteorological discontinuity sensors, remarks must be added to identify site-
specific sky conditions, which differ from conditions reported in the body of
the report. This remark must only be
generated when the ceiling is lower than that contained in the body of the report. For example, CIG_002_RY11.
X1 X1
Pressure Rising or
Falling Rapidly (PRESRR) (PRESFR)
Automated Remark
Only
Do Not Back Up
13.39
When the pressure is rising or falling rapidly at the time of the observation,
the remark Pressure Rising Rapidly (PRESRR) or Pressure Falling Rapidly
(PRESFR) is included.
X X
Sea-Level Pressure
(SLPppp) (SLPNO)
Automated Remark
Only
Do Not Back Up
13.40
At stations with automated systems with
SPECI capability and manual stations,
this remark begins with SLP and is coded using the tens, units, and tenths
of sea-level pressure in hectopascals,
for example, SLP982. If sea-level pressure would normally be reported, but is not available, the remark is coded
SLPNO.
X
Aircraft Mishap (ACFT_ MSHP) 13.41
If a report was taken to document weather conditions when notified of an
aircraft mishap, the remark ACFT MSHP is included in the report, but is
not transmitted. This is indicated by putting the remark in parenthesis in the
record.
X X
Other Significant Information (Plain Language) › X
07/1/2021 JO 7900.5E, Chg 1
Element
Snow Increasing
Rapidly
(SNINCR_(ii)/(ii))
At Designated sites in
Appendix F)
Paragraph
13.42
Brief Description
Report SNINCR if snow depth increases by 0.5 inch to the nearest whole inch or more in the past hour,
followed by amounts. The remark SNINCR is followed by the depth of increase in the last hour, a solidus, and the total depth of snow on the ground at
the time of the report. For example, a snow depth increase of 2 inches in the
past hour with a total depth on the ground of 10 inches would be coded
"SNINCR 2/10".
METAR
X
SPECI
Other Significant Information (Plain
Language)
13.43
Other significant information important
to operations, such as information on
fog dispersal operations, runway conditions, or "Last" report from a
manual location, etc.
X X
Water Equivalent of Snow on Ground (933RRR) (At Designated sites in… › X
07/1/2021 JO 7900.5E, Chg 1
Group 2`-Additive and Automated Maintenance Data
Element Paragraph Brief Description METAR SPECI
Hourly Precipitation
Amount (Prrrr)
Automated Remark
Only Do Not Back Up
1-, 3- and 6-Hourly Ice Accretion Amount, I1nnn, I3nnn, I6nnn
Automated Remark
Only Do Not Back Up
3- and 6-Hourly Precipitation Amount,
6RRRR/ Automated Remark
Only Do Not Back Up
24-Hour Precipitation, 7R24R24R24R24
Automated Remark
Only Do Not Back Up
Depth of Snow on the
Ground, 4/sss (At Designated Sites
in Appendix F)
13.46
13.47
13.48
13.49
13.50
At automated stations this remark is included in METAR reports for the water
equivalent of all precipitation that has occurred since the last METAR coded in
hundredths of an inch, for example, P0009 indicates 9/100ths of an inch of
precipitation in the past hour. At automated stations with a freezing rain sensor, this remark is included in
METAR/SPECI reports for the ice accretion amount that has occurred in hundredths of an inch during the last 1hour (I1nnn), 3-hour (I3nnn), and 6-hour
(I6nnn) period. No manual backup is
required.
At stations equipped with automated
systems with SPECI capability and Manual stations, this remark is included in 3- and 6-hourly observation; encoded in inches, using tenths, and hundredths,
of the amt. 2.17 inches of precipitation
would be encoded 60217. When an indeterminable amount of precipitation
has occurred, the 6RRRR group is
coded 6////.
Included in 1200 UTC observation if more than a trace of precipitation has fallen in past 24 hours, coded using the
tens, units, tenths, and hundredths of inches, for example, 1.25 inches would
be coded 70125. At stations listed in Appendix F, the total snow depth on ground group is coded in
the 0000, 0600, 1200, and 1800 UTC
observations whenever there is more than a trace of snow on the ground For
example, a snow depth of 21 inches
would be coded as "4/021".
X
X
X
X
X
X
Water Equivalent of
Snow on Ground
(933RRR)
(At Designated sites in
Appendix F)
13.51
At manual stations, this group reported
in 1800UTC report if average snow depth is 2 inches or more. 933 is the code indicator for water equivalent of
snow on ground. RRR represents the water equivalent of snow on the ground
reported in tens, units and tenths of inches using 3 digits, for example, water
equivalent of 3.6 inches would be
933036.
X
07/1/2021 JO 7900.5E, Chg 1
Remarks Section of Observation
Element
Hourly Temperature
6 Hour Minimum Temperature, 2snTnTnTn (NA Automated Remark Only Do Not… › X
and Dew Point Tsn n d d d Automated Remark
Only Do Not Back Up
6-Hour Maximum Temperature,
1snTxTxTx Automated Remark
Only Do Not Back Up
Paragraph
13.52
13.53
Brief Description
At automated stations except AWOS-A,
this element is used to report temperature and dew point to the tenth
of a degree Celsius. T identifies the
group, the sn the sign of the temperature - coded as 1 if the value is
below 0 degrees Celsius and 0 if the value is 0 degrees Celsius or higher.
TaTaTa is the temperature in tens,
units, and tenths of degrees and T'aT'aT'a is the dew point in tens, units
and tenths of degrees, for example, a temperature of 2.6 and dew point of -1.5
would be coded in the body as 03/M01
and in remarks as T00261015.
The maximum temperature in past 6hours in tenths of degrees Celsius using
3 digits, where the 1 identifies the maximum temperature group, the sn the
sign of the temperature - coded as 1 if
the value is below 0 degrees Celsius and 0 if the value is 0 degrees Celsius
or higher. The TxTxTx must be the maximum temperature during the last 6
hours, for example, a temperature of 1.0 degrees Celsius is coded as 10010, a maximum temperature of -2.1 degrees Celsius is coded 11021.
METAR
X
X
SPECI
6 Hour Minimum Temperature, 2snTnTnTn (NA Automated Remark
Only Do Not Back Up
13.54
The minimum temperature in past 6hours in tenths of degrees Celsius using
3 digits where the 2 identifies the minimum temperature group, the sn the
sign of the temperature - coded as 1 if
the value is below 0 degrees Celsius
and 0 if the value is 0 degrees Celsius
or higher. The TnTnTn must be the minimum temperature during the last 6
hours, for example, a temperature of 2.1 degrees Celsius is coded as 21021, a minimum temperature of 1.2 degrees
Celsius is coded 20012.
X
TR › the remark TSNO is included.
07/1/2021 JO 7900.5E, Chg 1
Remarks Section of Observation
Element
24-Hour Maximum and Minimum Temperature, 4snTxTxTxsnTnTnTn Automated Remark
Only Do Not Back Up
Pressure Tendency,
5appp Automated Remark
Only Do Not Back Up
Paragraph
13.55
13.56
Brief Description
Reported at midnight (LST); the maximum and minimum temperatures for the day coded in tenths of degrees
Celsius using 3 digits where the 4
identifies the maximum/minimum temperature group, the sn the sign of
the temperature - coded as 1 if the value is below 0 degrees Celsius and 0
if the value is 0 degrees Celsius or
higher. For example, a 24-hour maximum temperature of 10.0 degrees
Celsius and a 24-hour minimum temperature of -1.5 degrees Celsius is
coded 401001015.
At equipped automated stations, include
in 3- and 6-hourly observations where
the 5 identifies the pressure tendency group, the a represents the character of
pressure change over the past 3 hours, and ppp is the change in pressure in the
past 3 hours. the ppp is coded based on
the absolute value of the change of
either the station pressure or the altimeter in the past 3 hours coded in
tenths of hectopascals and using the
tens, units, and tenths digits, for example, a steady increase of 3.2 hectopascals in the past 3 hours would
be coded 52032.
METAR
X
X
SPECI
Sensor Status
Indicators
Automated Remark
Only Do Not Back Up
13.57
At equipped automated stations: When automated stations are equipped with a precipitation identifier and that sensor is
not working, the remark PWINO is included. When the tipping bucket rain gauge is not operating at an automated station equipped with the device, PNO
is included in remarks. When automated stations are equipped with a
Freezing Rain Sensor and it is not
working, the remark FZRANO is included. When automated stations are
equipped with a lightning detection system and that sensor is not working,
X
the remark TSNO is included. At an automated station, when the secondary
visibility sensor is not working, VISNO_(LOC) is included, and when the cloud height indicator is not working
CHINO_(LOC) is included.
3.10 RecordKeepingandForms › 29
07/1/2021 JO 7900.5E, Chg 1
Remarks Section of Observation
Element Paragraph Brief Description METAR SPECI
Maintenance Indicator
Automated Remark
Only Do Not Back Up
13.58
A maintenance indicator sign, $, is included when an ASOS/AWOS-C detects that maintenance is needed on
the system.
X X
X Indicates elements included at all stations A Indicates elements that are at service level A B Indicates elements that are at service level B 1At stations equipped with meteorological discontinuity sensors.
Order_JO_7900.5E › Chapter 4. General Procedures at Automated Weather Stations
Chapter 4. General Procedures at Automated Weather Stations
4.1. Purpose. This chapter prescribes procedures and practices to be followed by personnel responsible for observing, reporting, and/or transmitting surface weather information required for augmentation, and/or for sustaining minimum operations in the event of partial or total failure of the automated weather observing system. Practices applicable to LAWRS observers are located in Appendix C.
4.2. Types of Automated Stations. There are two major classes of automated surface weather observing systems used at FAA, FAA-contract, and NF-OBS sites: Automated systems with SPECI capability and automated systems without SPECI capability. The augmentation and backup of these systems are described in the next two chapters.
a. Automated systems with SPECI capability.
(1) Automated Surface Observing System (ASOS) is a type of automated surface weather observing system developed through a joint FAA/NWS/DOD agreement. ASOSs are installed at designated airports and maintained by the NWS to meet FAA requirements. ASOS contains at least one of each of the following sensors:
i. Wind speed and direction sensor.
ii. Visibility sensor.
iii. Precipitation identification sensor.
iv. Cloud height indicator sensor.
v. Temperature and dew point sensors.
vi. Pressure sensors.
vii. Precipitation accumulation sensor.
(2) ASOS may also include a freezing precipitation sensor, in addition to all of the above sensors and thunderstorm reporting via the Automated Lightning Detection and Reporting System (ALDARS).
(3) Many sites have an ASOS/ATIS Interface Unit (AAIU), which provides the capability to broadcast current weather from the ASOS over the ATIS/AFIS ground-to-air radio when the tower/FSS is closed.
(4) ASOS may also have an interface to new generation RVR equipment. See Chapter 9, Runway Visual Range (RVR).
(5) FAA AWOS-C (AWOS Type FA-29600) - Is an AWOS modified by the FAA to report METAR/SPECI data similar to an ASOS.
NOTE: Any reference to ASOS includes the AWOS-C and any future NextGen system with SPECI capability.
b. Automated systems without SPECI capability. Automated Weather Observing System (AWOS). AWOS is a type of automated surface weather observing system certified and commissioned by the FAA. Non-Federal AWOS systems are owned and maintained by the airport. A/C 150/5220-16 provides guidance to the owner for commissioning into the NAS. AWOS systems typically disseminate weather reports every 20 minutes and do not issue SPECI observations. ATCT’s with LAWRS certified observers collocated with a non-Federal AWOS must adhere to FAA JO 7210.3, Paragraph 2-9-2 d. At Non-Federal AWOS Sites facilities must:
(1) FAA facilities must negotiate a letter of agreement (LOA) with the airport management or appropriate authority at locations where a non-Federal AWOS is installed at an airport with an operating control tower. The LOA must define equipment maintenance responsibilities and coordination requirements.
(2) ATCS’s may disseminate only those non-Federal weather observations METAR/ SPECI that are obtained through the Weather Message Switching Center (WMSCR) or other equivalent documented means.
(3) Pilots who want non-Federal AWOS information from sites that do not include automatic long-line dissemination should be provided the appropriate frequency and/ or telephone number, if known.
4.3. Procedures for Handling Aircraft Mishaps at Automated Sites. The requirement to record the present weather following an aircraft mishap remains valid at automated sites. At a minimum, a mishap requires weather data from 1 hour before to 1 hour after the mishap occurs.
ASOS observations should be archived by the observer or by calling the AOMC
(1-800-242-8194). The AOMC has the capability to archive the 5-minute observations from the previous 12 hours of weather observation data from attended and unattended locations. The supervisor or controller-in-charge must ensure that the 5-minute observations are archived following notification of an aircraft mishap at a location where an ASOS is operational. AOMC requests must be made within 10 hours of the incident. Archive AWOS data in accordance with the procedures in the AWOS Technical Instruction Book.
4.4. Notice to Airmen (NOTAMs). The ASOS/AWOS is used to observe local weather conditions and broadcast weather information to pilots. All weather observers (LAWRS, CWO, NF-OBS etc.) are prohibited from appending NOTAM information to the automated weather system. Guidance for ATIS broadcasts are contained in FAA JO 7210.3 and 7110.65.
Order_JO_7900.5E › Chapter 5. Augmentation Requirements at Automated Weather Stations
Chapter 5. Augmentation Requirements at Automated Weather Stations
5.1. Introduction. This chapter prescribes procedures and practices applicable to the augmentation of automated surface observations at all FAA, FAA-contract, and NF-OBS facilities. In addition, this chapter also prescribes specific differences in augmentation procedures and practices applicable to LAWRS observers, as well as tower visibility requirements.
5.2. Validity of Data. Once an observation has been augmented, the observer must ensure the augmented data is correct prior to transmission.
5.3. Sign On/Sign Off the Automated Weather Observing Systems. In order to ensure the observation is correct and to enter augmentation data into the automated weather observing system, the observer must:
a. Sign on the automated weather observation system when on duty. Sign on must be in accordance with the respective automated weather observing system’s operator handbook or locally prescribed procedures. The "AUTO" tag at the beginning of the observation will be dropped when the observer signs on.
b. At part-time facilities, the observer must sign off an automated system with SPECI capability at the close of augmentation coverage of the METAR. This includes all surface, LAWRS and tower visibility observers. Prior to signing off the automated weather observation system, the observer must ensure the Present Weather Sensor has been RESET.
c. When using an ASOS (N/A AWOS-C), several augmented events (for example, tornadic activity, thunderstorm, or hail) automatically generate SPECI observations for the beginning and ending of the event. If one of these events is occurring at the close of augmentation coverage, it will be necessary to end the event. The ending of the event will automatically generate a SPECI. (e.g., GR occurring at closing or TS occurring at closing). After the SPECI transmits, Reset/Enable the Present Weather Sensor (PRESWX). The observer must then sign off the automated weather observing system.
NOTE: If a Thunderstorm was reported by ALDARS it is not necessary to end the event prior to closing. ALDARS will generate a SPECI ending the event when lightning is no longer detected.
d. Virga and volcanic ash are events that do not generate SPECIs. Virga is automatically deleted from the observation after the hourly METAR is transmitted. If virga continues to occur, it must be re-entered. If volcanic ash (VA) is occurring at the close of augmentation coverage, it will be necessary to end the event Reset/Enable the Present Weather Sensor (PRESWX) and Enter “Last” in the remarks followed by the remark “VA occurring at closing.”
e. Sign On/Sign Off the AWOS. At AWOS sites, the observer must sign on/sign off the automated weather observing system following the procedures stated in the AWOS Operator’s Instructions.
Table 5-1: Summary of FAA Augmentation Requirements
ELEMENT
TOWERED with
ASOS/AWOS-C
NON-TOWERED
with ASOS/AWOS-C
Non-Fed AWOS site
with Surface Observer
LAWRS with
a Non-Fed
AWOS 2 LAWRS w/ OBS1 FSS or OBS
Thunderstorm T6 O6 F6 O T
Tornadic Activity3 T O F O T
Hail T O F O T
Virga T O F O T
Volcanic ash T O F O T
Weather4 T O F O T
Tower Visibility N/A T5 N/A T5 N/A
1 Towered site with a surface-based observer. 2 Augmentation is provided by manually disseminating 3 Includes tornado, waterspout, and funnel cloud. 4 See Table 6-3 for complete list of required elements. 5 Tower visibility either provided to observer for input or entered via operator interface device. 6 Augmented at Sites without ALDARS capability, Backup at sites with ALDARS capability.
Legend: F - Augmentation provided by certified FSS observer or FAA-contract observer O - Augmentation provided by surface-based observer T - Augmentation provided by certified tower observer
5.4. Augmentation Observing Procedures. Except as specified in the following subsections, observing procedures for augmentation must be the same as specified for the corresponding manual observation in Chapters 7 through 12 depict elements to be augmented for each service level.
a. Observing Tornadic Activity. The term tornadic activity must include funnel clouds, tornadoes, and waterspouts. Observing procedures for tornadic activity are given in Paragraph 9.22, Observing and Reporting Tornado, Waterspout, or Funnel Cloud. A funnel cloud, tornado, or waterspout is considered to begin at the time it is observed by the observer. A funnel cloud, tornado, or waterspout is considered to end at the time it disappears from sight.
b. Observing Thunderstorms. Observing procedures for thunderstorms are given in Paragraph 9.23, Observing and Reporting Thunderstorms and Paragraph 9.24, Beginning and/or Ending of a Thunderstorm. A thunderstorm occurrence begins when thunder is first heard, lightning is observed over the station and the local noise level is sufficient to prevent hearing thunder, or when lightning is detected by an automated sensor within ten miles of the airport. A thunderstorm is considered to end 15 minutes after the last occurrence of any of these criteria.
c. Observing Hail. Observing procedures for hail are given in Paragraph 9.25, Reporting Hail. Hail begins at the time it is first observed falling and ends when it is no longer observed falling. No intensity must be assigned to hail; that is, the observer must not characterize hail as light, moderate, or heavy.
d. Observing Volcanic Ash. Observing procedures for volcanic ash are given in Paragraph 9.32, Special Procedures for Volcanic Ash. The observer must report volcanic ash whenever it is observed at the station.
e. Observing Virga. Virga is defined as precipitation falling from clouds but not reaching the ground. The observer must report virga when observed. Virga is not considered to be present weather or an obscuration.
f. Observing Tower Visibility. Tower visibility is only reported at sites with both an operating control tower and a surface weather observer. Observing procedures for tower visibility are given in Paragraph 8.3, Control Tower Visibility and observations and actions at collocated sites.
5.5. General Reporting Procedures. Report tornadic activity (to include funnel clouds, tornadoes, or waterspouts), thunderstorm, hail, volcanic ash, virga, or tower visibility by making the appropriate entry on the operator's interface device in accordance with procedures in the appropriate handbooks, manuals or Ready Reference Guide. Thunderstorm activity may also be reported by an automated sensor. If Thunderstorm or Lightning activity is reported by an automated sensor, it is not necessary for an observer to duplicate or report the same activity.
a. Reporting Tornadic Activity. The term tornadic activity must include funnel clouds, tornadoes, and waterspouts. These phenomena must be reported in a SPECI observation whenever they are observed or disappear from sight. At sites with an automated system with SPECI capability, the event will continue to be reported automatically until the observer deletes the entry.
b. Reporting Thunderstorms. At sites with automated systems with SPECI capability, entry or deletion of a thunderstorm report must be made by the observer or an automated sensor. The event will continue to be reported automatically until the observer or ALDARS deletes the entry. A SPECI observation is generated automatically for the beginning and ending times of thunderstorms. A thunderstorm occurrence begins when thunder is first heard, when lightning is
observed at the station and the local noise level is sufficient to prevent hearing thunder, or when lightning is detected by an automated sensor within ten miles of the airport. Location and direction of movement of the thunderstorm and the location, type, and frequency of lightning must be reported, if known. LAWRS personnel are only required to annotate the beginning/ending times of thunderstorms.
c. Reporting Hail. At sites with an automated system with SPECI capability, entry or deletion of a hail report must be made. The event will continue to be reported automatically until the observer deletes the entry. Hail begins when it is first observed and ends when it is no longer falling. No intensity must be assigned to hail; that is, the observer must not characterize hail as light or heavy. Hail size should be reported, if known.
d. Reporting Volcanic Ash. “VA” is the standard contraction used for volcanic ash. It will be reported in the body of the report as an obscuration whenever observed. At sites with an automated system with SPECI capability, the event will continue to be reported automatically until the observer deletes the entry. A special observation is not required when volcanic ash is observed. No intensity is assigned to volcanic ash; that is, the observer must not characterize volcanic ash as light, moderate, or heavy. Remarks are optional, but if the volcanic eruption producing the volcanic ash is observed, it must be entered in remarks, and a special observation must be generated.
e. Reporting Virga. When precipitation is observed to be falling from clouds, but is not reaching the ground, the observer must report VIRGA in remarks. There is no standard contraction used for virga. Virga is not considered to be present weather or an obstruction to vision. In remarks, VIRGA is spelled out in full. At sites with an automated system with SPECI capability, the event will continue to be reported automatically until the observer deletes the entry or until after the next hourly observation. The remark VIRGA will not be automatically kept in remarks of the observation past the next hourly observation. If virga persists, it must be re-entered as a remark. No SPECI is required when virga is observed. No intensity is assigned to virga; that is, the observer must not characterize virga as light, moderate, or heavy. The direction of the virga from the site is optional.
f. Reporting Tower Visibility. At towered sites with an automated system with SPECI capability with a surface-based observer, a tower visibility report must be made by notifying the surface-based observer or using the appropriate entry on the operator’s interface device. The reporting of tower visibility must be in accordance with coding and dissemination procedures specified in Paragraph 13.24, Tower or Surface Visibility (TWR_VIS_vvvvv or SFC_VIS_vvvvv).
Table 5-2: Examples of Augmented Observations
Examples of Augmented Observations
Automated system without SPECI capability w/o Aug
METAR KHEF 011755Z AUTO 21020G35KT 1SM OVC010 27/24 A2991 RMK AO1 (NA LAWRS)
Examples of Augmented Observations
Automated system without SPECI capability w/ Aug
METAR KHEF 011755Z 21020G35KT 1SM +TSRA OVC010CB 27/24 A2991 RMK AO1 WEA:TSRA OCNL LTGCG OHD TS OHD MOV E
Automated system with SPECI capability w/o Aug
METAR KGLD 011755Z AUTO 21020G35KT 1SM +RA OVC010 27/24 A2991 RMK AO2 SLP101
Automated system with SPECI capability w/ Aug
METAR KBHM 011755Z 21020G35KT 1SM +TSRA OVC010CB 27/24 A2991 RMK AO2 OCNL LTGCG OHD TSB42 TS OHD MOV E SLP101
Automated system with SPECI capability w/o Aug with ALDARS
METAR KSEG 171753Z AUTO 21020G30KT 1SM TSRA OVC010 27/24 A2991 RMK AO2 LTG DSNT E TSB42 SLP101
Automated system with SPECI capability w/ Aug and ALDARS
METAR KAOO 011753Z 21020G35KT 1SM TSRA OVC010CB 27/24 A2991 RMK AO2 LTG DSNT E TSB42 TS OHD MOV E SLP101
Order_JO_7900.5E › Chapter 6. Backup/Editing Requirements at Automated Weather Stations
Chapter 6. Backup/Editing Requirements at Automated Weather Stations
6.1. Introduction. This chapter presents the procedures and practices for providing the backup weather information required in the event of a partial or total failure of the automated weather observing system or if one or more of the elements within the automated observation are judged erroneous or non-representative. Responsible personnel must provide the backup weather information specified in Chapter 2, Guidelines. During periods when backup is required, augmentation must also be performed.
Table 6-1: Summary of Long-line Backup Requirements
ELEMENT
TOWERED
NON TOWERED WITH OBSERVER1 LAWRS NON-LAWRS WITH
OBSERVER1
Wind T O O
Visibility to 10 Miles T O O
Present Weather & Obscurations2 T O O
Sky Condition to 12K Ft. T O O Temperature/Dew Point T O O
Altimeter Setting T O O
Tower Visibility N/A T N/A
1 Includes all FSS, FAA-Contract, and non-Federal observers. 2 See Table 6- for required elements.
Legend: T - Element provided by certified Air Traffic Control Specialist O - Element provided by surface-based observer
6.2. Validity of Data. Once an observation has been edited/backed up, the observer must ensure the augmented data is correct prior to transmission.
6.3. Equipment Requirements. The following equipment is required to provide the weather information specified in this chapter. Unless stated otherwise, the equipment is required only if that element is required at your facility. References to an "OID/OT" indicate any automated weather observing system operator interface device.
a. Equipment for Wind Direction and Speed. If available, the primary low-level wind shear alert system (LLWAS) sensor or other FAA approved on-site wind equipment (F-420, SAWS, SWS etc.) must be used. Otherwise, the wind direction and speed must be estimated using the Beaufort scale during periods when all automated wind sensors are inoperative.
b. Equipment for Visibility. There is no equipment required for automated visibility sensor backup. However, a current list or visibility chart(s) depicting day and night visibility reference points must be maintained and available at the point of observation for use at each facility. See FAA JO 7210.3.
c. Equipment for Present Weather and Obstructions to Vision. Visual procedures must be used to identify the type(s) of present weather and/or obscurations. If necessary, visual procedures must be used to determine the intensity of precipitation.
d. Equipment for Sky Condition. There is no equipment required for automated sky condition sensor backup. Visual estimates must be made using the manual techniques such as:
(1) Pilot reports (PIREPS) of cloud heights may be used if available. PIREPs normally reference Mean Sea Level (MSL), and must be converted to Above Ground Level (AGL) for inclusion into the METAR/SPECI.
(2) Terminal Aerodrome Forecast (TAF) data.
(3) METAR/SPECI from near-by adjacent airports.
e. Equipment for Temperature and Dew Point. An FAA approved remote readout hygrothermometer (Standalone Weather Sensor System (SAWS), Surface Weather System (SWS)) is an acceptable backup for temperature and dew point. Other acceptable backups are a battery-operated self-contained psychrometer or a stand-alone temperature-measuring device, as approved by FAA.
f. Equipment for Altimeter Setting. Equipment to back up altimeter setting may be any FAA installed and maintained altimeter setting indicator (ASI), digital altimeter setting indicator (DASI), SAWS, SWS, or any other FAA approved facility station pressure instrument.
g. Equipment for OID/OT. Whenever possible, backup of missing or erroneous data must be entered using the ASOS/AWOS-C OID. If the OID fails on automated systems with SPECI capability and the automated systems with SPECI capability observation is currently representative, the observer must continue to maintain oversight of the automated system through other methods. (e.g. relocate to another site with an OID/VDU, Internet, telephone broadcast). Coordinate with the ATCT and disseminate appropriate maintenance notifications to AOMC for ASOS, the NEMC for AWOS-C or Alaskan SOC for AWOS-C in Alaska.
When operationally significant weather is occurring or expected to occur:
(1) If able, arrange for local and long-line communications to be disabled. If long-line communications cannot be disabled, do not enter weather reports into an alternate system (e.g. AISR).
(2) Provide manual backup observations.
(3) Surface observers must coordinate with ATCT; anytime weather reports are disseminated through alternate methods they must be relayed to the ATCT for ATIS broadcast.
NOTE: An ATCT with digital ATIS must manually edit the weather observations that are entered via alternate methods.
(4) Notify all other users that have an ASOS interface OID, VDU, IDS-4, and/or IDSR etc. This may include the TRACON, Airport Operations, Fixed Based Operator and/or other local aviation stakeholders. It is the observer’s responsibility to know where all interfaces and displays are located.
(5) Operationally significant weather is defined as:
i. Marginal VFR conditions (ceilings 1000-3000 feet and/or visibility 3SM -5SM)
ii. IFR conditions (ceilings at or below 1000 feet and/or visibility at or below 3SM)
iii. Thunderstorm activity
iv. Any form of precipitation.
h. Equipment for Communications. No additional equipment is required for the longline communication of weather information.
(1) At manual ATIS locations or uncontrolled airports (including NF-OBS, SAWRS), when long-line communications are unavailable, the report must be relayed to the overlying ARTCCs Flight Data unit for entry into an FAA approved electronic system that provides NAS-wide dissemination (e.g., AIS-R, SWIM, or similar systems). In Alaska, disseminate weather reports to the FSS.
NOTE: If the weather observer has the capability to enter the weather into an FAA approved electronic system without calling the ARTCC they may do so.
(2) At digital ATIS locations, the weather observer must continue to use the OID to augment/edit the METAR/SPECI. The digital ATIS will continue to broadcast the augmented weather reports that are entered by the weather observer. The weather observer must also ensure that all weather reports are entered into their alternate system for NAS-wide dissemination.
6.4. Procedures for Providing Backup Information. At sites with an automated system with SPECI capability, required weather data elements must be entered into the automated weather observing system using the editing procedures for the OID.
For Non-Representative data, enter representative data into the appropriate field using the OID. Do not enter the data in the Remarks. When a certified weather observer edits/augments an automated weather system, it is transparent to the users.
a. Do not turn off report processing off (automated system with SPECI capability) or set the channel out of service (automated system without SPECI capability) unless directed to by maintenance personnel. Turning off report processing will lead to a "$" sign, and the generation of a trouble ticket for the NWS AOMC.
b. Observers must never turn off report processing for altimeter setting without appropriate maintenance notification. Once the report processing for the altimeter setting is turned off, only the appropriate ASOS or AWOS technician can turn the report processing back on.
6.5. Coding of Missing Data. If any element normally included in the body of the observation, except present weather and obscurations, is missing because of sensor failure and the lack of backup equipment, that element may be omitted. If the automated weather observing system's processor is operative, the system will do this automatically. If not operative, these missing elements must be omitted and skipped over. When an element or phenomena does not occur or cannot be observed, the corresponding group and preceding space are omitted from that particular report.
6.6. Procedures for Wind Speed and Wind Direction. FAA approved backup wind equipment (LLWS, WME, F-420, SAWS, SWS etc.) must be used to determine wind direction and speed. If no backup sensor is available, wind speed and direction must be estimated using the Beaufort scale (Table 7-1). When the wind is estimated, enter the estimated wind data into Wind field of the METAR in the same manner as if it were read from instruments.
a. Estimating Wind Direction. Wind direction must be estimated by observing the wind cone or tee, movement of twigs, leaves, smoke, etc., or by facing into the wind in an unsheltered area. When estimating wind direction, note that even small obstacles may cause variations. The movement of clouds, regardless of how low they are, must not be used for estimating the surface wind direction.
b. Estimating Wind Speed. The Beaufort scale (see Table 7-1: Estimating Wind Speed) must be used to estimate wind speed if all other wind speed measuring instruments are out of service.
6.7. Procedures for Visibility. The visibility reported must be a prevailing visibility. The prevailing visibility must be determined using a visibility chart, list or photographs. See FAA JO 7210.3.
NOTE: RVR is not addressed here because an ASOS/RVR automated interface will not be backed up by controllers or weather observers (including LAWRS). If the ASOS/RVR interface fails, the data will be omitted.
a. Reporting Visibility Values. In backing up visibility, the reportable values for visibility must be the manual visibility values as permitted by the current system software installed; see Table 8-1: Reportable Visibility Values. If the actual visibility falls between two reportable values, the lower value must be reported.
b. Tower Visibility. At towered facilities with a surface-based observer, the responsible tower controller must enter the tower visibility into the OID or:
(1) Notify the surface-based observer via landline when the tower prevailing visibility is observed to decrease to less than, or if below, increases to equal or exceed, 4 miles.
(2) Report all changes of one or more reportable values to the surface-based observer when the prevailing visibility at the tower or the surface is less than 4 miles.
(3) As required by FAA directives, use the lower of either the tower or weather station visibility as controlling visibility for aircraft operations.
6.8. Procedures for Present Weather and Obscurations. Present weather and obscurations to vision must be observed and reported in accordance with the manual procedures prescribed in Chapter 9, Weather Phenomena. Reports must include as a minimum those weather phenomena in Table 6-2: Backup and Augmentation Weather and Obscurations, when backing up automated systems with SPECI capability. (If the observer is backing up automated systems with SPECI capability at the close of augmentation/backup coverage, it will be necessary to end the event or it will continue to be reported during the hours when there is no augmentation/backup coverage.) Precipitation of unknown form is generally only reported when the automated weather observing system present weather indicator sensor is operational and is reporting precipitation of unknown form. However, if the observer can determine the type of precipitation, it should be reported according to the guidelines in Table 6-2, via the non-representative data procedures.
NOTE: Except for the Present Weather and Altimeter sensor, when sensor data is backed up or edited by the controller/observer, the sensor will revert to automated mode for the next scheduled METAR. The Present Weather sensor must be reset by the controller/observer or the automated system will continue to report the phenomenon that was manually entered by the controller/observer. Once the altimeter field is edited, the sensor must be reset by a technician.
Table 6-2: Backup and Augmentation Weather and Obscurations
PHENOMENON OBSERVED
REPORT (NOTATION) PHENOMENON OBSERVED
REPORT (NOTATION)
Tornado +FC (in body); TORNADO (in remarks)
Snow Pellets GS
Funnel Cloud FC (in body); FUNNEL CLOUD (in remarks)
Volcanic Ash VA
Waterspout +FC (in body); WATER- SPOUT (in remarks)
Fog (Vsby <5/8) FG
Thunderstorm TS Mist (Vsby ≥ 5/8) BR Rain RA Shallow (ground) Fog
MIFG
Rain Shower Report RA for automated systems with SPECI capability
Patchy Fog BCFG
Drizzle DZ Freezing Fog FZFG Freezing Rain FZRA Blowing Snow BLSN Freezing Drizzle FZDZ Haze HZ Ice Crystals Report SN for automated systems with SPECI capability
Smoke FU
Ice Pellets PL Squalls SQ
PHENOMENON OBSERVED
REPORT (NOTATION) PHENOMENON OBSERVED
REPORT (NOTATION)
Ice Pellet Showers Report PL for automated systems with SPECI capability
Dust DU
Hail GR Snow SN Snow Showers Report SN for automated systems with capability Snow Grains Report SN for automated systems with SPECI capability
6.9. Procedures for Sky Condition. Details on procedures for observing sky condition are included in Chapter 10, Sky Condition. If required, the following procedures for reporting sky condition must apply:
a. Report sky cover up to 12,000 feet, or as specified in the designated service level standard, whichever is greater. (See Appendix D. Service Standards.)
b. Non-opaque cloud layers must be treated as opaque and reported.
c. No more than three layers may be reported; or as specified in the designated service level standard, whichever is greater. (See Appendix D. Service Standards.)
d. "CLR" (clear) must be reported at an automated site when no clouds are visible up to 12,000 feet, or as specified in the designated service level standard, whichever is greater.
NOTE: At all locations with an automated weather observation system that report “CLR” during non-operating hours, the controllers/observers should also report “CLR” during operating hours. Only full-time manual weather stations should use the contraction “SKC”.
6.10. Procedures for Temperature and Dew Point (See Chapter 11). If either or both of the temperature and dew point modules of the automated weather observing system are inoperative, both the temperature and dew point must be reported using readings from FAA approved backup equipment (psychrometer, SAWS, SWS etc.). If approved backup equipment is not available, the temperature/dew point fields are omitted.
a. Reporting Procedures for Temperature. The temperature must be entered as two digits to the nearest whole degree Celsius (C). Sub-zero temperatures must be prefixed with an M (minus). For example, a temperature of 4 degrees Celsius with a dew point of -2oC is coded as 04/M02. See Paragraph 3.9, Rounding Off Numbers for rounding off procedures. A temperature of -0.5oC must be reported as M00 to indicate that the actual temperature is below zero but rounded to zero.
b. Reporting Procedures for Dew Point. The dew point temperature must be entered as two digits to the nearest whole degree Celsius. Sub-zero dew point temperatures must be prefixed with an M. When the dry-bulb temperature is -34.4°C or below, the dew point must be reported as unavailable. For example, when the temperature is -36, it will be reported as M36/.
6.11. Procedures for Altimeter Setting (See Chapter 12). The observer must use an ASI, DASI, SAWS, SWS, or any other altimeter setting source approved by the FAA that meets altimeter and comparison check requirements of the latest version of FAA Order JO 7210.3, Facility Operation and Administration.
a. On an ASOS/AWOS-C, if the altimeter setting is missing, enter the Altimeter setting reading from the approved backup source into the Altimeter field on the OID. The altimeter will need to be re-entered for each weather report until a technician resets and calibrates the pressure sensors.
b. If performing manual weather observations, use the readings from the approved backup source when preparing the METAR/SPECI for transmission.
Table 6-3: Automated System without SPECI Capability Backup Observation Examples
Automated system without SPECI capability observation with all sensors fully operational and no observer or augmenter on duty:
METAR JHW 011255Z AUTO 30005KT 7SM BKN110 06/03 A2991 RMK AO1 SLP101
Automated system without SPECI capability observation with ceilometer and anemometer not operational and no backup observer on duty:
METAR JHW 011255Z AUTO 7SM 06/03 A2991 RMK AO1 SLP101
Automated system without SPECI capability observation with ceilometer and anemometer not operational and with backup observer on duty:
METAR JHW 011255Z 30005KT 7SM BKN110 06/03 A2991 RMK AO1 SLP101
Table 6-4: Automated System with SPECI Capability Backup Observation Examples
Automated system with SPECI capability observation with all sensors fully operational and no observer or augmenter on duty:
METAR KIAD 011255Z AUTO 30005KT 7SM BKN110 06/03 A2991 RMK AO2 SLP101
Automated system with SPECI capability observation with ceilometer and anemometer not operational and no backup observer on duty:
METAR KIAD 011255Z AUTO 7SM 06/03 RMK AO2 SLP101 $
Automated system with SPECI capability observation with ceilometer and anemometer not operational and with backup observer on duty:
METAR KIAD 011255Z 30005KT 7SM BKN110 06/03 A2991 RMK AO2 SLP101 $
Continue reading ↓ 120 of 428 passages shown