Radar Vectors
FAA Order Cancelled Issued May 11, 2001 AJT-2 267 pages Copy saved Nov 18, 2026

Order 7900.5B Surface Weather Observing

This document is cancelled. Cancelled by JO 7900.5C. Check the official source before relying on it.

Official source ↗ Open PDF

Text read by OCR from a scanned file (1 of 267 pages). Check the original, as some words may be misread.

acover.pdf

ORDER 7900.5B

SURFACE WEATHER OBSERVING

May 11, 2001

DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION Distribution: A-W(AT/TO/TX/TA/RS/RU/RW/RN/FS)-2; A-X(AT)-2; Initiated By: ATP-300 A-Y(AY)-2; A-FAT-0 (STD); AND-400 2 cys; ZAT-464; DOD; NWS; USCG Elizabeth City Facility

bforward.pdf › FOREWORD

5/11/01 7900.5B

Page i (and ii)

FOREWORD The Federal Aviation Administration (FAA) recognizes that the aviation weather system is a national system and that continued safe and efficient air transportation requires FAA commitment and leadership to aviation weather services. This order provides the practices and procedures to make weather observations an important part of the FAA’s overall weather services. The practices and procedures set forth in this order apply to all FAA personnel, FAA-contract personnel, and Non-Federal Observer personnel who provide aviation weather observation services. These personnel are required to be familiar with the provisions of this order that pertain to their observational responsibilities and to exercise their judgment if they encounter situations not covered by this order. Bill G. Peacock Director of Air Traffic

ctoc.pdf

5/11/01 7900.5B

Page iii

TABLE OF CONTENTS FOREWORD … i CHAPTER 1. INTRODUCTION … 1

1-1. Purpose … 1 1-2. Distribution … 1 1-3. Cancellation … 1 1-4. Effective Date … 1 1-5. Explanation of Changes … 1 1-6. Abbreviations and Acronyms … 1 1.7 Relationship to FMH-1 and Other Documents … 1 1-8. Applicability of Procedures and Practices … 2 1-9. User Responsibilities … 3 1-10. Changing the Order … 3 1-11. Maintaining the Order … 3 CHAPTER 2. GUIDELINES … 5

2-1. Introduction … 5 2-2. Types of Stations … 5 2-3. General Types of Observations … 6 2-4. Augmentation Requirements … 6 2-5. Backup Requirements … 8 2-6. Long-Line Backup Requirements … 9 2-7. Certification of Personnel and Currency Requirements … 10 2-8. Types and Content of METAR/SPECI Observations … 10 Figure 2-1. Guide to Contents of Automated and Manual Aviation Routine Weather Reports (METAR) and Aviation Selected Special Weather (SPECI) Observations … 12 CHAPTER 3. GENERAL PROCEDURES … 15

3-1. Introduction … 15 3-2. Definitions … 15 3-3. Aviation Weather Observing Locations … 15 3-4. General Observing Practices … 16 3-5. Dissemination … 17 3-6. Dissemination Requirements … 17 3-7. Corrections to Transmitted Data … 17 3-8. Delayed Reports … 17 3-9. Rounding Off Numbers … 18 3-10. Record Keeping and Forms … 18 3-11. Evaluating Weather Sensor Accuracy … 18 3-12. Documentation of Observing Location and Facilities … 19 Figure 3-1. Station Information File … 20

7900.5B 5/11/01

Page iv

CHAPTER 4. GENERAL PROCEDURES AT AUTOMATED WEATHER STATIONS … 21

4-1. Purpose … 21 4-2. Definitions … 21 4-3. Types of Automated Stations … 22 4-4. Certification … 23 4-5. General Procedures … 23 4-6. General Equipment Procedures … 23 4-7. Procedures at Non-Federal Observation (NF-OBS) Sites … 24 4-8. Procedures at Non-Federal AWOS Sites … 24 4-9. Procedures for Handling Aircraft Mishaps at Automated Sites … 24 4-10. General Requirements for Record Keeping … 24 Figure 4-1. Operator Procedures for Providing Augmentation and Backup Information … 26 4-11. - 4-12. Reserved … 27 CHAPTER 5. AUGMENTATION AT AUTOMATED WEATHER STATIONS … 29

5-1. Introduction … 29 5-2. Validity of Data … 29 5-3. Sign On/Sign Off the Automated Weather Observing Systems … 29 Figure 5-1. Summary of FAA Augmentation Requirements … 30 5-4. Order for Reporting Weather and Obstructions to Visibility … 31 5-5. Augmentation Observing Procedures … 31 5-6. Reporting Procedures … 31 5-7. Examples of Augmented Observations … 33 Figure 5-2. Examples of Augmented Observations … 33 5-8. - 5-9. Reserved … 34 CHAPTER 6. BACKUP REQUIREMENTS AT AUTOMATED WEATHER STATIONS … 37

6-1. Introduction … 37 6-2. Summary of Backup Requirements … 37 6-3. Validity of Data … 37 Figure 6-1. Summary of Long-line Backup Requirements … 38 6-4. Equipment Requirements … 38 6-5. Procedures for Providing Backup Information … 39 Figure 6-2. Backup Reporting of Wind or Altimeter Setting … 40 6-6. Coding of Missing Data … 40 6-7. Procedures for Wind Speed and Wind Direction … 40 Figure 6-3. Estimating Wind Speed … 41 Figure 6-4. Backup Reporting of Tower/Surface Visibility … 42

5/11/01 7900.5B

Page v

6-8. Procedures for Visibility … 42 Figure 6-5. Backup Reporting of Weather Phenomena … 43 6-9. Procedures for Present Weather and Obscurations … 43 Figure 6-6. Backup and Augmentation Weather and Obscurations … 44 Figure 6-7. Backup Reporting of Sky Condition … 45 6-10. Procedures for Sky Condition … 45 Figure 6-8. Priority for Reporting Cloud Layers … 46 Figure 6-9. Criteria for Variable Ceiling … 46 Figure 6-10. Increments of Reportable Values of Sky Cover Height … 47 Figure 6-11. Reportable Contractions for Sky Cover Amount … 47 6-11. Procedures for Temperature and Dew Point … 47 Figure 6-12. Backup Reporting of Temperature and Dew Point … 48 6-12. Procedures for Altimeter Setting … 48 6-13. Procedures for Documentation … 48 6-14. Procedures for Communications … 48 6-15. Disposition of MF1M-10C … 48 6-16. Examples of Backup Observations … 48 6-17. Malfunctions/Outages … 49 Figure 6-13. AWOS Backup Observation Examples … 49 Figure 6-14. ASOS Backup Observation Examples … 49 6-18. - 6-19. Reserved … 50 CHAPTER 7. GENERAL PROCEDURES FOR MANUAL OBSERVATIONS … 53

7-1. Introduction … 53 7-2. Observational Procedures … 53 7-3. Definition of Actual Time of Observation … 53 7-4. General Procedures … 53 7-5. Observer Responsibility … 53 7-6. Weather Watch … 53 7-7. Basic Weather Watch … 53 7-8. Continuous Weather Watch … 54 7-9. Types of Manual Surface Observations … 54 7-10. Aviation Routine Weather Reports (METAR) … 54 7-11. Aviation Selected Special Weather Reports (SPECI) … 54 7-12. SPECI Observations Upon Resumption of Observing Function … 54 7-13. Criteria for SPECI Observations … 54 7-14. Content of METAR/SPECI Observations … 56 Figure 7-1. Content of METAR (Manual/Automated) … 57 7-15. - 7.16. Reserved … 68

7900.5B 5/11/01

Page vi

CHAPTER 8. WIND … 71

8-1. Introduction … 71 8-2. Definitions … 71 8-3. Observing, Determining, and Reporting Procedures … 71 8-4. Wind Direction … 71 8-5. Estimating Wind Direction … 72 8-6. Variable Wind Direction … 72 8-7. Wind Shifts … 72 8-8. Wind Speed … 72 8-9. Estimating Wind Speed … 73 Figure 8-1. Corrections to Indicated Wind Speeds … 73 Figure 8-2. Estimating Wind Speed … 73 8-10. Wind Character (Gusts) … 74 8-11. Peak Wind Speed … 74 8-12. Calm Wind … 74 8-13. Conversion of True and Magnetic Winds … 74 8-14. Instrumental Evaluation Procedures … 75 8-15. Recorder Adjustments … 75 8-16. Annotation of Wind Recorder Charts … 75 8-17. Changing Charts … 75 8-18. Disposition … 75 8-19. Conversion of Wind Speed … 76 8-20. Operation of Equipment … 76 Figure 8-3. Conversion of Miles per Hour to Knots … 76 Figure 8-4. Conversion of Knots to Miles per Hour … 76 CHAPTER 9. VISIBILITY … 77

9-1. Introduction … 77 9-2. Definitions … 77 9-3. Visibility Standards … 77 9-4. Unit of Measure … 77 9-5. Observing Aids for Visibility … 77 9-6. Tower Visibility Aids … 78 9-7. Selection of Visibility Markers … 78 9-8. Observation Sites … 78 9-9. Dark Adaptation … 78 9-10. Evaluating Visibility … 78 9-11. Evaluating Prevailing Visibility … 78 9-12. Evaluating Sector Visibility … 78 9-13. Evaluating Variable Visibility … 78 9-14. Reportable Visibility Values … 79 9-15. Control Tower Observations and Actions at Co-Located Sites … 79 9-16. Additional Tower Personnel Action for Tower Visibility … 79 9-17. Weather Station/Contract Observer Action at Stations with Control Tower … 79 Figure 9-1. Reportable Visibility Values … 80 9-18. - 9.19. Reserved … 80

5/11/01 7900.5B

Page vii

CHAPTER 10. RUNWAY VISUAL RANGE … 83

10-1. Introduction … 83 10-2. Definitions … 83 10-3. Sensor and Method … 83 10-4. Observing Positions … 84 10-5. Day-Night Observations for Transmissometers … 84 10-6. Automated Long-Line RVR Observations … 84 10-7. Multiple RVRs … 84 10-8. Units of Measure … 84 10-9. RVR Based on Transmissometer … 84 10-10. Automated RVR … 84 10-11. Limits of RVR … 84 10-12. Variation in RVR … 85 10-13. Determining and Reporting RVR (NA LAWRS) … 85 10-14. RVR Procedures (Apply to RVRs Using Transmissometer Technology Only) … 85 10-15. Ten-Minute RVR Values (Apply to RVRs Using Transmissometer Technology Only) … 85 10-16. Manually Determined One-Minute RVR Values (Apply to RVRs Using Transmissometer Technology Only) … 86 10-17. Emergency Reporting of Runway Visibility and Runway Visual Range (Apply to RVRs Using Transmissometer Technology Only) (NA LAWRS) … 86 10-18. Annotation of RVR Recorder Charts (Apply to RVRs Using Transmissometer Technology Only) … 86 10-19. Disposition of RVR Recorder Charts (Apply to RVRs Using Transmissometer Technology Only) … 87 10-20. Operation of Equipment … 87 Figure 10-1. RVR Transmittance Conversion Table for Tasker 400 and Equivalent Systems with 250-Foot Baseline - Contrast Threshold 5.5 Percent … 88 Figure 10-2. Tasker 500 RVR Transmittance Conversion Table for 250-Foot Baseline - Contrast Threshold 5.0 Percent … 89 10-21. - 10.23. Reserved … 90 CHAPTER 11. WEATHER PHENOMENA … 95

SECTION 1. WEATHER PHENOMENA - GENERAL … 95 11-1. Introduction … 95 11-2. Precipitation … 95 11-3. Obscurations … 96 11-4. Other Phenomena … 98 11-5. Qualifiers … 98 11-6. Order for Reporting Multiple Types of Weather and Obscurations … 98 Figure 11-1. Present Weather … 99 11-7. Rules for Phenomena Not Occurring at the Point of Observation … 99

SECTION 2. OBSERVING AND REPORTING PRECIPITATION … 101 11-8. Reporting and Documenting Precipitation … 101 11-9. Beginning and/or Ending of Precipitation (NA LAWRS) … 101 11-10. Determining and Reporting the Type of Precipitation … 101 11-11. Determining the Character of Precipitation … 101

7900.5B 5/11/01

Page viii

11-12. Precipitation Intensity … 101 Figure 11-2. Estimating Intensity of Rain … 102 Figure 11-3. Estimating Intensity of Ice Pellets … 102 Figure 11-4. Intensity of Rain or Ice Pellets Based on Rate of Fall … 102 Figure 11-5. Intensity of Snow or Drizzle Based on Visibility … 102 Figure 11-6. Precipitation Intensity Symbols … 103 11-13. Intensity of Snow, Snow Pellets, Snow Grains, Drizzle and Freezing Drizzle … 103 11-14. Reporting Freezing Precipitation … 103 11-15. Beginning and/or Ending of Freezing Precipitation … 103 11-16. Intensity of Freezing Precipitation … 103 11-17. Reporting Ice Pellets … 103 11-18. Beginning and/or Ending of Ice Pellets (NA LAWRS) … 103 11-19. Intensity of Ice Pellets … 104 11-20. Reporting Precipitation Amounts (NA LAWRS) … 104 11-21. Priority of Gauges (NA LAWRS) … 104 Figure 11-7. Units of Measure for Precipitation … 104 11-22. Stick Measurement of Liquid Precipitation (NA LAWRS) … 104 11-23. Determining Water Equivalent of Solid Precipitation by Stick Measurement (NA LAWRS) … 104 11-24. Determining Water Equivalent of Solid Precipitation by Weighing (NA LAWRS) … 105 11-25. Estimating the Water Equivalent of Snow (NA LAWRS) … 105 Figure 11-8. New Snowfall to Estimated Meltwater Conversion Table … 106 11-26. Determination of 6-Hour Accumulation of Precipitation (NA LAWRS) … 107 11-27. Depth Measurement of Solid Forms (NA LAWRS) … 107 11-28. Snowfall within Specified Periods (NA LAWRS) … 107

SECTION 3. OBSERVING AND REPORTING TORNADOES, WATERSPOUTS, AND FUNNEL CLOUDS … 109 11-29. Tornado, Waterspout, or Funnel Cloud … 109

SECTION 4. OBSERVING AND REPORTING THUNDERSTORMS, HAIL, LIGHTNING, AND SQUALLS … 110 11-30. Reporting Thunderstorms … 110 11-31. Beginning and/or Ending of a Thunderstorm … 110 11-32. Reporting Hail … 110 11-33. Beginning and/or Ending of Hail (NA LAWRS) … 110 11-34. Reporting Lightning … 111 Figure 11-9. Type and Frequency of Lightning … 111 11-35. Reporting Squalls … 111

SECTION 5. OBSERVING AND REPORTING PROCEDURES FOR OBSCURATIONS … 112 11-36. General … 112 11-37. Observing Obscurations … 112 11-38. Reporting Obscurations … 112 11-39. Special Procedures for Volcanic Ash … 112

5/11/01 7900.5B

Page ix

11-40. Operationally Significant Remarks for Obscurations … 112 CHAPTER 12. SKY CONDITION … 113

SECTION 1. INTRODUCTION TO SKY CONDITION … 113 12-1. Introduction … 113 12-2. Sky Condition Evaluation … 113 12-3. Cloud Forms and Obscuring Phenomena … 113

SECTION 2. DEFINITIONS … 114 12-4. Ceiling … 114 12-5. Celestial Dome … 114 12-6. Cloud … 114 12-7. Cloud Movement … 114 12-8. Field Elevation … 114 12-9. Horizon … 114 12-10. Interconnected Cloud Layers … 114 12-11. Layer … 114 12-12. Layer Amount … 114 12-13. Layer Height … 115 12-14. Multiple Layers … 115 12-15. Obscuring Phenomena … 115 12-16. Sky Cover … 115 12-17. Sky Cover Classifications … 115 12-18. Summation Amount … 115 12-19. Summation Principle … 115 12-20. Surface … 116 12-21. Total Amount … 116 12-22. Variable Ceiling … 116 12-23. Variable Sky Condition … 116

SECTION 3. OBSERVING AND REPORTING PROCEDURES … 117 12-24. Observing Sites … 117 12-25. Layer Amounts … 117 12-26. Summation Layer Amount … 117 12-27. Layer Heights … 117 Figure 12-1. Reportable Contractions for Sky Cover … 118 Figure 12-2. Priority for Reporting Layers … 118 Figure 12-3. Increments of Reportable Values for Layer or Ceiling Heights … 118 12-28. Evaluation of Multiple Layers … 119 12-29. Amount of Obscuration … 119 12-30. Determining Amount of Sky Cover … 119 12-31. Evaluation of Sky Cover Amounts … 119 12-32. Sky Cover Classification … 119 12-33. Variable Sky Cover … 119 12-34. Non-Uniform Sky Cover … 120 12-35. Estimated Ceiling Heights … 120 12-36. Variable Ceiling Height … 121 Figure 12-4. Criteria for Variable Ceiling … 121

7900.5B 5/11/01

Page x

12-37. Significant Clouds … 121 12-38. Cloud Types (NA LAWRS) … 121 12-39. Operation of Equipment … 122 Figure 12-5. Examples: Summation of Sky Cover … 122 Figure 12-6. Convective Cloud-Base Height Diagram … 123 CHAPTER 13. TEMPERATURE AND DEW POINT … 125

13-1. Introduction … 125

SECTION 1. DEFINITIONS … 125 13-2. Temperature … 125 13-3. Hygrometer … 125 13-4. Hygrothermograph … 125 13-5. Hygrothermometer … 125 13-6. Instrument Shelter … 125 13-7. Maximum Thermometer … 125 13-8. Minimum Thermometer … 125 13-9. Psychrometer … 126 13-10. Psychrometric Calculator … 126 13-11. Psychrometric Tables … 126 13-12. Relative Humidity … 126 13-13. Sling Psychrometer … 126 13-14. Townsend Support … 126 13-15. Thermograph … 126 13-16. Wet-Bulb Depression … 126

SECTION 2. TEMPERATURE AND DEW POINT OBSERVING PRACTICES … 127 13-17. Temperature and Dew Point Observing Practices - General … 127 13-18. Dry- and Wet-Bulb Temperatures (NA LAWRS) … 127 13-19. Dew Point Temperatures (NA LAWRS) … 127 13-20. Obtaining Psychrometric Data … 128 13-21. Hygrothermometer (NA LAWRS) … 128 13-22. Manually or Motor Aspirated Psychrometer (NA LAWRS) … 128 Figure 13-1. Chilled Mirror Hygrothermometers - Dew Point Comparison Difference in °F (e.g., HO-83, 1088, etc.) … 129 Figure 13-2. Chilled Mirror Hygrothermometers - Dew Point Comparison Difference in °C (e.g., HO-83, 1088, etc.) … 130 13-23. Psychrometric Computations … 130

SECTION 3. OBSERVING, DETERMINING, AND REPORTING PROCEDURES … 131 13-24. Station Primary System (NA LAWRS) … 131 13-25. Hygrothermometer (NA LAWRS) … 131 13-26. Liquid-in-Glass Thermometer (NA LAWRS) … 131 13-27. Thermograph or Hygrothermograph (NA LAWRS) … 131 13-28. Dry-Bulb and Dew Point Temperature (NA LAWRS) … 131 13-29. Maximum and Minimum Temperature (NA LAWRS) … 132 13-30. Relative Humidity Computations … 132

5/11/01 7900.5B

Page xi

SECTION 4. OBSERVING AND REPORTING PROCEDURES AT LAWRS (ONLY LAWRS) … 133 13-31. Station Primary System (ONLY LAWRS) … 133 13-32. Hygrothermometer Operating Range (ONLY LAWRS) … 133 13-33. Evaluating Hygrothermometer Data (ONLY LAWRS) … 133 13-34. Psychrometer (ONLY LAWRS) … 133 13-35. Dew Point Temperatures (ONLY LAWRS) … 133 13-36. Psychrometer Observing Procedures (ONLY LAWRS) … 134 13-37. Psychrometric Evaluations (ONLY LAWRS) … 134 13-38. Psychrometric Computations (ONLY LAWRS) … 134 13-39. Dew Point Conversion (ONLY LAWRS) … 134 CHAPTER 14. PRESSURE … 135

14-1. Introduction … 135

SECTION 1. DEFINITIONS … 135 14-2. Altimeter Setting (ALTSG) … 135 14-3. Atmospheric Pressure … 135 14-4. Barometric Pressure … 135 14-5. Field Elevation, Ha … 135 14-6. Pressure Altitude, PA … 135 14-7. Pressure Change (NA LAWRS) … 136 14-8. Pressure Characteristic (NA LAWRS) … 136 14-9. Pressure Falling Rapidly (NA LAWRS) … 136 14-10. Pressure Rising Rapidly (NA LAWRS) … 136 14-11. Pressure Tendency (NA LAWRS) … 136 14-12. Sea Level Pressure … 136 14-13. Standard Atmosphere … 136 14-14. Station Elevation, Hp … 137 14-15. Station Pressure … 137 14-16. Density Altitude, DA … 137 14-17. Barometer Elevation, HZ … 137 14-18. Posted Pressure Correction … 137 14-19. Reserved … 137

SECTION 2. OBSERVING, DETERMINING AND REPORTING PROCEDURES (NA LAWRS) … 138 14-20. General (NA LAWRS) … 138 Figure 14-1. Units of Measure of Pressure Parameters … 138 14-21. Rounding Pressure Values … 138 14-22. Barometers Used to Measure Station Pressure (NA LAWRS) … 138 Figure 14-2. Barometers Used … 138 14-23. Precision Aneroid (NA LAWRS) … 138 14-24. Altimeter Setting Indicator (NA LAWRS) … 139 14-25. Digital Altimeter Setting Indicator (DASI) (NA LAWRS) … 139 14-26. Barograph (NA LAWRS) … 139 14-27. Mercury Barometer (NA LAWRS) … 139 14-28. Sea Level Pressure (NA LAWRS) … 140

7900.5B 5/11/01

Page xii

14-29. Determining Altimeter Setting (NA LAWRS) … 141 14-30. Method of Determining Altimeter Setting (NA LAWRS) … 141 14-31. Altimeter Setting Indicator (NA LAWRS) … 141 14-32. Pressure Reduction Computer and Altimeter Setting (NA LAWRS) … 141 14-33. Altimeter Setting Reduction Constant (NA LAWRS) … 142 14-34. Altimeter Setting Table (NA LAWRS) … 142 Figure 14-3. Portion of an Altimeter Setting Table … 142 14-35. Pressure Altitude (PA) (NA LAWRS) … 142 14-36. Local Pressure Altitude Tables (NA LAWRS) … 142 14-37. Altimeter Setting and Pressure Reduction Computer (NA LAWRS) … 142 14-38. Altimeter Setting and Pressure Altitude Table (NA LAWRS) … 143 14-39. Station Pressure and Pressure Reduction Computer (NA LAWRS) … 143 14-40. Station Pressure and Pressure Altitude Table (NA LAWRS) … 143 Figure 14-4. Pressure Altitude … 145 14-41. Pressure Related Remarks (NA LAWRS) … 148 14-42. Pressure Falling Rapidly (NA LAWRS) … 148 14-43. Pressure Rising Rapidly (NA LAWRS) … 149 14-44. Pressure Tendency (NA LAWRS) … 149 14-45. Frequency of Pressure Tendency Remark (NA LAWRS) … 149 14-46. Determining Pressure Change (NA LAWRS) … 149 14-47. Determining Pressure Tendency Characteristic (NA LAWRS) … 149

SECTION 3. OBSERVING, DETERMINING AND REPORTING PROCEDURES AT LAWRS … 150 14-48. Applicability (ONLY LAWRS) … 150 14-49. General (ONLY LAWRS) … 150 14-50. Determining Altimeter Setting (ONLY LAWRS) … 150 14-51. Altimeter Setting from Altimeter Setting Indicators (ONLY LAWRS) … 150 14-52. Determining the Reliability of Altimeter Setting Indicators (ONLY LAWRS) … 150 14-53. Daily Comparison with an Adjacent Station (ONLY LAWRS) … 151 14-54. Altimeter Setting from a Mercury Barometer (ONLY LAWRS) … 151 14-55. Altimeter Setting from a DASI … 151 14-56. Electronic Pressure Transducers or Other DASI's … 151 14-57. - 14-60. Reserved … 152 CHAPTER 15. CODING AND DISSEMINATION … 155

15-1. Introduction … 155 15-2. Definitions … 155 15-3. Aviation Weather Reports Code … 155 Figure 15-1. Content of METAR/SPECI … 156 15-4. Format and Content of the METAR/SPECI Report … 156 Figure 15-2. METAR or SPECI Code Format … 156 15-5. Coding Missing Data in METAR and SPECI Reports … 157 15-6. Coding the Body of the METAR or SPECI Report … 157 15-7. Type of Report (METAR or SPECI) … 157

5/11/01 7900.5B

Page xiii

15-8. Station Identifier (CCCC) … 157 15-9. Date and Time of Report (YYGGggZ) … 157 15-10. Report Modifier (AUTO or COR) … 157 15-11. Wind Group ((dddff(f)Gfmfm(fm)KT)_(dndndnVdxdxdx) … 158 15-12. Visibility Group (VVVVVSM) … 158 Figure 15-3. Reportable Visibility Values … 159 15-13. Runway Visual Range Group (RDRDR/VRVRVRVRFT) or (RDRDR/VnVnVnVnVVxVxVxVxFT) (NA LAWRS) … 159 15-14. Present Weather Group (w'w') … 160 Figure 15-4. Present Weather … 160 15-15. Sky Condition Group (NsNsNshshshs or VVhshshs or CLR or SKC) … 163 Figure 15-5. Reportable Values for Sky Cover Amount … 164 Figure 15-6. Increments of Reportable Values of Sky Cover Height … 164 15-16. Temperature/Dew Point Group (T'T'/T'dT'd) … 164 15-17. Altimeter (APHPHPHPH) … 165 15-18. Remarks (RMK) … 165 15-19. Automated, Manual, and Plain Language Remarks … 165 15-20. Volcanic Eruptions … 165 15-21. Funnel Cloud (Tornadic Activity_B/E(hh)mm_LOC/DIR_(MOV)) … 166 15-22. Type of Automated Station (AO1 or AO2) … 166 15-23. Peak Wind (PK WND_dddff(f)/(hh)mm) (NA LAWRS) … 166 15-24. Wind Shift (WSHFT_(hh)mm) … 166 15-25.

Tower or Surface Visibility (TWR_VIS_vvvvv or SFC_VIS_vvvvv) … 167 15-26. Variable Prevailing Visibility (VIS_VnvnvnvnvnVvxvxvxvxvx) … 167 15-27. Sector Visibility (VIS_[DIR]_vvvvv) … 167 15-28. Visibility at Second Location ((VIS)_vvvvv_[LOC]) (NA LAWRS) … 167 15-29. Lightning Frequency (Frequency_LTG(Type)_[LOC]) … 167 Figure 15-7. Type and Frequency of Lightning … 168 15-30. Beginning and Ending of Precipitation (w'w'B(hh)mmE(hh)mm) (NA LAWRS) … 168 15-31. Beginning and Ending of Thunderstorms (TSB(hh)mmE(hh)mm) … 168 15-32. Thunderstorm Location (TS_LOC_(MOV_DIR)) … 169 15-33. Hailstone Size (GR_[size]) … 169 15-34. Virga (VIRGA_(DIR)) … 169 15-35. Variable Ceiling Height (CIG_hnhnhnVhxhxhx) … 169 15-36. Obscuration (w'w'_[NsNsNs]hshshs) … 169 15-37. Variable Sky Condition (NsNsNs(hshshs) _V_NsNsNs) … 169 15-38. Significant Cloud Type [Plain Language] … 170 15-39. Ceiling Height at Second Location (CIG_hhh_[LOC]) (NA LAWRS) … 170 15-40. Pressure Rising or Falling Rapidly (PRESRR OR PRESFR) (NA LAWRS) … 170 15-41. Sea-Level Pressure (SLPppp) (NA LAWRS) … 171 15-42.

Aircraft Mishap (ACFT_MSHP) … 171 15-43. No SPECI Reports Taken (NOSPECI) … 171 15-44. Snow Increasing Rapidly (SNINCR_(inches-hour/inches on ground)) (NA LAWRS) … 171 15-45. Other Significant Information … 171 15-46. Additive and Automated Maintenance Data … 171

7900.5B 5/11/01

Page xiv

Figure 15-8. Units of Measure for Precipitation … 172 15-47. Hourly Precipitation Amount (Prrrr) (NA LAWRS) … 172 15-48. 1, 3 and 6 Hourly Ice Accretion Amounts (I1nnn, I3nnn, I6nnn) (NA LAWRS) … 172 15-49. 3- and 6-Hour Precipitation Amount (6RRRR) (NA LAWRS) … 173 15-50. 24-Hour Precipitation Amount (7R24R24R24R24) (NA LAWRS) … 173 15-51. Snow Depth on Ground (4/sss) (NA LAWRS) … 173 15-52. Water Equivalent of Snow on Ground (933RRR) (NA LAWRS) … 174 15-53. Cloud Types (8/CLCMCH) (NA LAWRS) … 174 15-54. Duration of Sunshine (98mmm) (NA LAWRS) … 174 15-55. Hourly Temperature and Dew Point (TsnT'T'T'snT'dT'dT'd) (NA LAWRS) … 174 15-56. 6-Hourly Maximum Temperature (1snTxTxTx) (NA LAWRS) … 174 15-57. 6-Hourly Minimum Temperature (2snTnTnTn) (NA LAWRS) … 175 15-58. 24-Hour Maximum and Minimum Temperature (4snTxTxTxsnTnTnTn) (NA LAWRS) … 175 15-59. 3-Hourly Pressure Tendency (5appp) (NA LAWRS) … 175 Figure 15-9. Characteristics of Barometer Tendency … 176 Figure 15-10. 3-Hour Change in Pressure … 177 15-60. Sensor Status Indicators … 178 15-61. Maintenance Indicator … 178 15-62. Transmission Times … 178 CHAPTER 16. ENTRIES ON OBSERVATIONAL FORMS … 179

16-1. Introduction … 179 16-2. Entries on Meteorological Form 1M-10C (MF1M-10C) … 179 16-3. Writing Instrument … 179 16-4. Parenthetical Data … 179 16-5. Missing Data … 179 16-6. Late Observations … 179 16-7. Corrections … 180 16-8. Heading on Form MF1M-10C at LAWRS … 180 16-9. Heading on Form MF1M-10C at Other Stations (NA LAWRS) … 180 16-10. Entries on MF1M-10 by Columns … 180 16-11. Type of Observation (Column 1) … 180 16-12. Time of Observation (Column 2) … 180 16-13. Wind Direction (Column 3) … 180 16-14. Wind Speed (Column 4) … 180 16-15. Wind Gust (Column 5) … 181 16-16. Wind Variability (Column 6) … 181 16-17. Surface Visibility (Column 7a) Tower Visibility (Column 7b) … 181 16-18. Runway Visual Range (Column 8) … 181 16-19. Present Weather (Column 9) … 181 16-20. Sky Condition (Column 10) … 181 16-21. Temperature (Column 11) … 182 16-22. Dew Point Temperature (Column 12) … 182 16-23. Altimeter Setting (Column 13) … 182 16-24. Remarks (Column 14) … 182 16-25. Total Sky Cover (Column 17) … 182 16-26. Dry-Bulb Temperature (Column 19) … 182 16-27. Wet-Bulb Temperature (Column 20) … 182

5/11/01 7900.5B

Page xv

16-28. Station Pressure (Column 22) … 183 16-29. Observers Initials (Column 15) … 183 16-30. Time (Column 26) … 183 16-31. Observation Number (Column 27) … 183 16-32. Maximum Temperature (Column 31) and Minimum Temperature (Column 32) (NA LAWRS) … 183 16-33. Precipitation (Column 33) (NA LAWRS) … 184 16-34. Snowfall (Column 34) (NA LAWRS) … 184 16-35. Snow Depth (Column 35) (NA LAWRS) … 185 16-36. Station Pressure (Column 36) (NA LAWRS) … 186 16-37. Barograph (Column 37) (NA LAWRS) … 186 16-38. Barograph Correction (Column 38) (NA LAWRS) … 186 16-39. 24-Hour Maximum Temperature (Column 57) (NA LAWRS) … 186 16-40. 24-Hour Minimum Temperature (Column 58) (NA LAWRS) … 186 16-41. 24-Hour Precipitation (Column 59) (NA LAWRS) … 186 16-42. 24-Hour Snowfall (Column 60) (NA LAWRS) … 187 16-43. Snow Depth (Column 61) (NA LAWRS) … 187 16-44. Remarks, Notes, and Miscellaneous Phenomena (Block 65) … 188 16-45. Additional Instructions for Part-Time Stations … 188 16-46. Hourly Wind Data … 188 16-47. Additive Data Groups (NA LAWRS) … 189 16-48. Tailoring MF1M-10C, Synoptic Data and Summary of the Day (NA LAWRS) … 189 16-49. Notice of Corrections to Weather Records … 190 16-50. Example Form … 190 Figure 16-1. WS Form B-14 … 191 Figure 16-2. Example of Entries on MF1M-10C … 192 CHAPTER 17. OPERATION OF EQUIPMENT … 193

17-1. Introduction … 193

SECTION 1. CLOUD HEIGHT MEASUREMENT EQUIPMENT … 193 17-2. Preparation of Sky Cover Height Tables for Ceiling Lights … 193 17-3. Ceiling Light … 193 17-4. Maintaining Ceiling Light … 193 17-5. Maintaining Clinometer … 194 17-6. Care and Operation of Ceiling Balloons … 194 Figure 17-1. 10-Gram Balloon Ascension Rates … 196 Figure 17-2. 30-Gram Balloon Ascension Rates … 197

SECTION 2. PRECIPITATION MEASURING EQUIPMENT … 198 17-7. Weighing Rain Gauge … 198 17-8. Changing Weighing Rain Gauge Charts … 198 17-9. Weighing Rain Gauge - Winter Operation … 198 17-10. Weighing Rain Gauge - Summer Operation … 199 17-11. Weighing Rain Gauge - Winding the Clock … 199 17-12. Maintaining the Weighing Rain Gauge … 199 17-13. Weighing Rain Gauge - Dashpot … 199 17-14. Weighing Rain Gauge - Clocks … 199 17-15. Weighing Rain Gauge - Pens … 200 17-16. Weighing Rain Gauge - Bucket … 200

7900.5B 5/11/01

Page xvi

17-17. Weighing Rain Gauge - Evaluation Procedure … 200 Figure 17-3. Evaluation of Precipitation on Weighing Rain Gauge Chart … 201 17-18. Weighing Rain Gauge - Annotation of Charts … 201 17-19. Weighing Rain Gauge - Replacement of Charts … 202 17-20. Clock Inoperative on Weighing Gauge … 202 17-21. Zero Adjustment on Weighing Gauge … 202 17-22. Time Adjustment on Weighing Gauge … 202 17-23. Emptying the Gauge … 202 17-24. Ice Accretion Indicators … 202 17-25. Maintaining the Non-Recording Gauge … 203 17-26. Maintaining the Tipping Bucket Gauge … 203

SECTION 3. VISIBILITY MEASURING EQUIPMENT … 204 17-27. Transmissometer Operation … 204 17-28. Transmissometer Background Measurements and Adjustments … 204 17-29. Transmissometer Daily and Weekly Checks … 204 17-30. Transmissometer Readout Check … 204 Figure 17-4. Transmissometer Conversion Tables … 205 17-31. Transmission Variation … 205 17-32. Transmissometer Outage … 205 17-33. Transmissometer Restored to Service … 206

SECTION 4. PRESSURE MEASURING EQUIPMENT … 207 17-34. Obtaining Station Pressure from Mercury Barometers … 207 17-35. Reading the Mercury Barometer … 207 17-36. Mercury Barometer - Total Correction … 207 Figure 17-5. Mercury Barometer Readings Obtained from Various Types of Scales and Verniers … 208 Figure 17-6. International Table for Mercurial Barometer Temperature Correction … 209 17-37. Mercury Barometer - Scale Reading … 210 17-38. Correction of Mercury Barometer Readings … 210 17-39. Reading Barographs for Station Pressure … 210 17-40. Barograph Time Check … 211 17-41. Barograph Clock and Chart Scale … 211 17-42. Barograms … 211 Figure 17-7. Barogram … 212 Figure 17-8. Example of Intersecting Barogram Trace … 214 17-43. Adjustment of the Barograph Pen for Pressure … 214 17-44. Barograph Adjustment for Time … 214 17-45. Selection of Barogram … 214 17-46. Changing the Barogram … 215 17-47. Maintenance of Pressure Reduction Computer … 215 Figure 17-9. Selection of Barograms … 215

5/11/01 7900.5B

Page xvii

SECTION 5. BAROMETER COMPARISONS … 216 17-48. General … 216 17-49. Requirements for Standardizing Instruments … 216 17-50. Standardizing Procedures … 216 Figure 17-10. Sample of MF1-13, Barometer Comparison (Front) … 217 Figure 17-11. Sample of MF1-13, Barometer Comparison (Back) … 218 17-51. Routine Comparisons … 219 17-52. Disposition of Form MF1-13 … 219 SECTION 6. PERFORMANCE OF ANEROID INSTRUMENTS … 220 17-53. General … 220 17-54. Aneroid Barometer or Altimeter Setting Indicator … 220 17-55. Excessive Drift … 220 17-56. Inspection Comparisons … 220 17-57. Electronic Pressure Transducers … 220 SECTION 7. TEMPERATURE AND HUMIDITY MEASURING EQUIPMENT … 221 17-58. Dry-Bulb Thermometer … 221 17-59. Wet-Bulb Thermometer … 221 17-60. Wet-Bulb Thermometer - Temperature Above Freezing … 221 17-61. Wet-Bulb Thermometer - High Temperature and Low Humidity … 221 17-62. Wet-Bulb Thermometer - Temperatures Below Freezing … 221 17-63. Wet-Bulb Thermometer - Dry-Bulb Temperature Below 2.8 Degrees Celsius … 221 17-64. Psychrometric Ventilation … 222 17-65. Sling Psychrometer Ventilation … 222 17-66. Obtaining Readings from Sling Psychrometer … 222

SECTION 8. TEMPERATURE AND HUMIDITY GRAPHING EQUIPMENT … 223 17-67. Thermograph/Hygrothermograph Time Check Line … 223 17-68. Changing Thermograph/ Hygrothermograph Charts … 223 17-69. Annotation of the Thermograph Chart … 223 17-70. Thermograph/ Hygrothermograph Time Adjustment … 223 17-71. Thermograph/Hygrothermograph Temperature Adjustment … 224 17-72. Thermograph/ Hygrothermograph Disposition … 224 17-73. General Maintenance of Thermograph … 224 17-74. Maintenance of Thermograph Clock … 224 17-75. Maintenance of Thermograph Pen … 225

SECTION 9. HYGROTHERMOMETERS … 226 17-76. Hygrothermometer (HO-83, ASOS 1088, etc.) - General … 226 17-77. Hygrothermometer (HO-83) - Operations … 226 17-78. Hygrothermometer (HO-83) - Instrument Error Indications … 226 17-79. Hygrothermometer (HO-83) - Quality Control … 226 17-80. Hygrothermometer (HO-83, ASOS 1088, etc.) - Comparison Checks (NA LAWRS) … 226

SECTION 10. MEASURING EQUIPMENT - OTHER … 228 17-81. Psychrometric Calculator … 228 17-82. Psychrometric Data … 228

7900.5B 5/11/01

Page xviii

Figure 17-12. Selection of Psychrometric Calculator on Basis of Standard Atmosphere … 228 17-83. Using the Calculator … 228 17-84. Maintenance of Psychrometric Calculator … 228 17-85. Maintenance of Liquid-in-Glass Thermometers … 229 17-86. Maintenance of Psychrometers - Weekly Checks … 229 17-87. Maintenance of Psychrometers - Monthly Checks … 229 17-88. Instrument Shelter - Illumination … 229 17-89. Instrument Shelter - Maintenance … 229

SECTION 11. WIND RETRANSMITTER … 231 17-90. General … 231 17-91. Wind Retransmitter - Weekly Check … 231 Figure 17-13. Wind Speed Comparison Data … 232 17-92. Wind Retransmitter - Other Checks … 232 17-93. - 17-96. Reserved … 232 APPENDIX A. Abbreviations and Acronyms (6 pages) … A-1 APPENDIX B. Non-Federal Observing (NF-OBS) Program (1 page) … B-1 APPENDIX C. LAWRS Requirements (6 pages) … C-1 APPENDIX D. Service Standards (3 pages) … D-1 APPENDIX E. METAR User Aids (10 pages) … E-1 APPENDIX F. METAR/SPECI Report for Transmission (WS Form B-11) (1 page) … F-1

CHAPTER 1. INTRODUCTION › 1-7. RELATIONSHIP TO FMH-1 AND OTHER DOCUMENTS

10/18/05 7900.5B

CHAPTER 1. INTRODUCTION

1-1. PURPOSE This order prescribes aviation surface weather observing procedures and practices applicable to all FAA and FAA-contract personnel engaged in taking and reporting aviation surface observations, including Limited Aviation Weather Reporting Stations (LAWRS) personnel, Non-Federal Observation (NF-OBS) Program personnel, as well as United States Coast Guard (USCG) personnel as a component of the Department of Homeland Security (DHS). This order includes practices and procedures for both manual and automated observation locations. Also included are practices and procedures for augmentation of automated observations and backup information in the event of system failure, erroneous or nonrepresentative data. These procedures and practices are intended to provide a framework for identifying meteorological phenomena of importance to aviation and reporting their occurrence. 1-2. DISTRIBUTION. This order is distributed to select offices in Washington Headquarters; Air Traffic Organization – Terminal Service Areas, Office of Operations Planning, NAS Weather Office, Flight Standards Service, The Mike Monroney Aeronautical Center, The William J. Hughes Technical Center, the USCG Elizabeth City Facility, the Department of Defense, all terminal air traffic field facilities, all Alaska flight service stations, FAA-contract weather, and the National Weather Service (NWS). 1-3. CANCELLATION Order 7900.5A, Surface Weather Observing - METAR, dated July 1, 1996, is canceled.

1-4. EFFECTIVE DATE This order is effective December 1, 2005. 1-5. EXPLANATION OF CHANGES This change incorporates revisions that have occurred since the order was last revised on May 11, 2001. This change:

a. Updates the office of primary responsibility.

b. Updates distribution in accordance with the new Air Traffic Organization.

c. Updates the USCG to a component of DHS.

d. Revises the frequency of snow depth measurements.

e. Clarifies what is used to determine water equivalency of snow. 1-6. ABBREVIATIONS AND ACRONYMS Appendix A, Abbreviations and Acronyms, contains abbreviations and acronyms used within this order. 1-7. RELATIONSHIP TO FMH-1 AND OTHER DOCUMENTS

a. Federal Meteorological Handbook No. 1, Surface Weather Observations and Reports (FMH-1). FMH-1 prescribes surface weather observing standards applicable to all federal agencies engaged in taking and reporting surface aviation observations. FMH-1 also

CHAPTER 1. INTRODUCTION › 1-8. APPLICABILITY OF PROCEDURES AND PRACTICES

7900.5B 5/11/01

Page 2

prescribes the standard reporting and coding procedures used in the surface aviation observation. Order 7900.5B prescribes the procedures and practices to be followed by FAA, FAA-contract and NF-OBS personnel for the observing, reporting, and coding of surface observations which meet the federal standards. A brief description of the NF-OBS program is provided in Appendix B, Non-Federal Observation (NF-OBS) Program. This order complements, but does not change, the standards contained in FMH-1. b. The NWS Observing Handbook No. 7, Surface Observations, (WSOH-7). WSOH-7 provides procedures and practices for NWS and NWS-contract personnel which are similar to those in this order. c. Automated Weather Observing Systems Handbooks. A partial listing of the applicable handbooks necessary to operate the various automated weather observing systems includes: (1) Federal Aviation Administration, Operator Instructions, Automated Weather Observing System (AWOS), August 1, 1994, U.S. Department of Transportation, Washington, D.C. (2) Federal Aviation Administration, ASOS Ready Reference Guide (latest versions). 1-8. APPLICABILITY OF PROCEDURES AND PRACTICES a. Applicability. Except for LAWRS, the procedures and practices in this order apply to all facilities which have the capability to comply with the stated procedure or practice. Some procedures and practices vary at LAWRS sites. These differences are indicated throughout

the order where applicable. LAWRS observers shall comply with all the standard procedures and practices, except for these specifically indicated differences. Those sections which are not applicable to LAWRS are marked NA LAWRS in bold type after the section title. Similarly, sections which apply only to LAWRS are indicated with ONLY LAWRS. LAWRS requirements are excerpted in Appendix C, LAWRS Requirements. At an automated site ranked as Service Level C, the basic weather observing requirements are the same as a LAWRS observation. LAWRS observers are not required to back up the observation if measuring or observing equipment is not available. b. Conflicting Information. In case of conflicting information, the procedures and practices in this order take precedence. However, any applicable FAA air traffic orders take precedence over any procedures or practices in this order which are in conflict. Such conflicts should be brought to the attention of the originator of this order. c. Terminology. Throughout this order, the following terminology applies: (1) “Shall” indicates a procedure or practice which is mandatory at all applicable facilities. (2) “Should” indicates a procedure or practice which is recommended at all applicable facilities. (3) “May” indicates a procedure or practice which is optional. (4) “Will” indicates futurity; it is not a requirement to be applied to current practices.

CHAPTER 1. INTRODUCTION › 1-11. MAINTAINING THE ORDER

10/18/05 7900.5B

Page 3 (and 4)

d. Unforeseen Requirements. No set of procedures and practices can cover all possibilities in weather observing. The observer shall use good judgment, adhering as closely as possible to this order, to describe phenomena not adequately covered by specific instructions. Suggestions for possible changes in procedures and practices to cover such situations may be made through appropriate channels. e. Designated Stations and Service Standards. Throughout this order the phrase “designated stations” appears. This refers to facilities that have been instructed by the FAA to perform a specified task that is not required to be performed at all facilities. In many cases, a facility may be designated to perform a specified task based on the service standards set for an airport. See Appendix D, Service Standards. f. Regional, Field Office and Facility Procedures. The procedures in this order are the minimum requirements. Needs at the service area office and especially at the local level may dictate additional requirements. Service area or field offices may coordinate these additional requirements with the Terminal Services, Safety Operations and Support, Contract Weather Observation, (ATO-T), although it is not required.

1-9. USER RESPONSIBILITIES

Employee participation in directive writing and upkeep activities is encouraged. Any user who finds a subject matter conflict, an error, obsolete information or who would like to make recommendations or suggestions, should notify Safety Operations and Support, in writing. FAA Form 1320-19, Directive Feedback Information, is available for this purpose. If clarification or correction is urgently needed, you may call Safety Operations and Support for guidance, but you should also use the FAA Form 1320-19 as a follow-up to verbal conversation.

1-10. CHANGING THE ORDER

Changes, additions, deletions, and corrections will be issued as necessary. These changes will be issued by the Director of Terminal Safety and Operations Support, Contract Weather Observation, Attn: ATO-T, FAA.

1-11. MAINTAINING THE ORDER Each facility shall maintain a copy of the order, complete with changes and supplements for reference purposes. When inserting changes to the order, enter the number, effective date, initials, and date entered on the inside cover of this order.

eCHAPTER 2.pdf

10/18/05 7900.5B

CHAPTER 2. GUIDELINES 2-1. INTRODUCTION This chapter describes the types of aviation surface weather observing facilities for which the FAA may have responsibility or oversight. This chapter also describes the various types of surface weather reports, including the Aviation Routine Weather Report (METAR) and Aviation Selected Special Weather Report (SPECI), and FAA guidelines regarding the content of each of these types. Also presented are general guidelines regarding augmentation and backup of automated observations. Lastly, this chapter presents FAA guidelines on the certification of observers. 2-2. TYPES OF STATIONS The generic types of stations that take aviation weather observations are defined as follows: a. Automated Station. A facility equipped with an automated surface weather observing system that prepares the observation without a certified observer on duty. The various types of automated stations are described in Chapter 4, General Procedures at Automated Weather Stations. b. Augmented Station. A facility with an automated surface weather observing system that prepares the METAR/SPECI with a certified observer on duty capable of adding operationally significant weather information to the observation. The observer is completely responsible for the observation, even though the automated weather observing system generates the report. At facilities where augmentation is not available full time, the facility is classed as automated during the non-augmented periods.

c. Manual Station. A facility where certified weather observers are responsible for observing, evaluating and preparing the METAR/SPECI. At these facilities, various degrees of automated sensors and/or other automated equipment may be available. However, the observer is completely responsible for the METAR/SPECI. d. Towered Station. Any facility with an air traffic control tower operated by the FAA or operated under an FAA contract. e. Non-Towered Station. Any facility without an FAA or FAA contract air traffic control tower. f. Limited Aviation Weather Reporting Station (LAWRS). A facility where observations are taken, prepared and transmitted by certified FAA or FAA-contract control tower personnel or Flight Service Station personnel on a limited basis to support aviation requirements. At these facilities, various degrees of automated sensors and/or other automated equipment may be available. However, when the facility is open, the LAWRS observer is completely responsible for the METAR/SPECI. At an automated site ranked as Service Level C, the basic weather observing requirements are the same as a LAWRS observation.

g. Flight Service Station. Throughout this order, the term Flight Service Station (FSS) refers to any Flight Service Station, Automated Flight Service Station (AFSS), Auxiliary Flight Service Station, or former FSS airport facility which has been directed by FAA headquarters or service area office to provide the observing, augmentation or backup service indicated.

7900.5B 5/11/01

h. Supplementary Aviation Weather Reporting Station (SAWRS). This program is maintained by the NWS. To obtain more information, contact the nearest NWS Weather Forecast office.

i. Non-Federal Observing (NF-OBS) Station. A program in which Non-Federal observers such as Non-Federal control tower (NFCT) controllers, airline personnel or fixed base operator (FBO) personnel may enter into an agreement with the appropriate FAA region to provide backup and augmentation of the Automated Surface Observing System (ASOS). NF-OBS observers are certified by NWS. At these facilities, various degrees of automated sensors and/or other automated equipment may be available. However, when on duty, the NF-OBS observer shall provide backup and augmentation in accordance with their NF-OBS agreement. Program establishment is contained in Appendix B, Non-Federal Observing (NF-OBS) Program, and responsibilities are described in Chapter 4, General Procedures at Automated Weather Stations. j. A-Paid Station. A facility where contract observers take only hourly observations (METAR). SPECI observations are not taken at these facilities. 2-3. GENERAL TYPES OF OBSERVATIONS There are two general types of surface observations: a. Automated Observation. Any observation which has been evaluated, prepared and transmitted by an automated observing system without human intervention. The automated observing systems to which this order applies include only Automated Surface

Observing Systems (ASOS) and the Automated Weather Observing Systems (AWOS). (1) Augmentation. Any automated observation to which additional weather information has been manually added that is beyond the capabilities of the automated weather observing system and/or is deemed operationally significant. The guidelines concerning augmentation are presented in paragraph 2-4. (2) Backup. A method of providing an observation, part of an observation, documentation, or communication of an observation at selected sites when the primary method is unavailable or non-representative. The guidelines concerning manually provided backup information are presented in paragraph 2-5, Backup Requirements. b. Manual Observation. Any observation for which the human observer observes, evaluates, prepares, records, and transmits the observation without the use of an automated observing system. The guidelines for manual observations are presented in Chapter 7, General Procedures for Manual Observations. 2-4. AUGMENTATION REQUIREMENTS Certified observers are responsible for the completeness and accuracy of the weather observation. Automated weather observing systems are, by design, viewing a smaller area than a human observer. Therefore, the observer is responsible for providing additional information that covers a larger area, when operationally significant. Augmentation of automated observations shall be provided in accordance with the guidelines presented in the following subsections and as specified for the station’s service level standard (Appendix D, Service Standards). Separate guidelines are

5/11/01 7900.5B

presented for the two general types of automated weather observing systems: ASOS and AWOS. Procedures and practices to be followed to accomplish the required augmentation are presented in Chapter 4, General Procedures at Automated Weather Stations, and Chapter 5, Augmentation at Automated Weather Stations. a. Control Tower with ASOS. (1) Control Tower without a Surface-Based Observer. At facilities with a control tower and with ASOS, but without a surface-based observer on duty, the tower observer shall provide augmentation of the automated observation. This augmentation shall include, but not be limited to:

(a) thunderstorm (b) tornadic activity (including tornado, waterspout and funnel cloud)

(c) hail

(d) virga

(e) volcanic ash (f) any weather elements considered operationally significant by the observer (2) Control Tower with a Surface-Based Observer. At facilities with a control tower, with ASOS and with a surfacebased observer on duty, the surface-based observer shall provide augmentation of the automated observation. This augmentation shall include, but not be limited to the requirements contained in Service Standards for that level of airport (see Appendix D, Service Standards). At these facilities, the control tower shall routinely provide tower visibility when applicable.

b. Facilities without Control Towers with ASOS. At these facilities, augmentation shall be the responsibility of the co-located Flight Service Station or contract weather observer (CWO) at designated stations. This augmentation shall include, but not be limited to: (1) thunderstorm (2) tornadic activity (including tornado, waterspout, and funnel cloud) (3) hail (4) virga (5) volcanic ash (6) any weather elements considered operationally significant by the observer c. Facilities with AWOS. At these facilities, the observation shall be the responsibility of the surface-based observer if one exists. At towered sites without a surface-based observer, the observation shall be the responsibility of the LAWRS observer. (Note: Augmentation is not possible at AWOS facilities without an operator interface device.) (Appendix E, METAR User Aids, contains a quick reference for METAR codes.) The augmentation provided by the observer shall be manually entered into the system for transmission via the operator terminal keyboard. If a “hot key” is not available for a particular augmentable element, the augmentation entries shall be manually entered into the remarks portion of the observation and shall be limited to 80 characters including spaces. The following elements shall be provided:

7900.5B 5/11/01

(1) Thunderstorms. (2) Precipitation occurring at the point of observation, limited to type plus intensity. Allowable reports are listed in Figure 6-6, Backup and Augmentation Weather and Obscurations, and in Appendix E, METAR User Aids. (3) Obscurations (alone or in combination with precipitation) at the point of observation. Allowable reports are listed in Figure 6-6 and in appendix E. (4) Operationally significant, localized weather conditions, not listed above, as follows: (a) hail (b) virga (c) tornadic activity* (includes tornado, waterspout, or funnel cloud)

(d) volcanic ash* (e) any weather elements considered operationally significant by the observer Note: Only those episodes of weather phenomena listed above that are occurring within a five mile radius of the airport, and/or that pose an operational hazard for aircraft in the airport area shall be reported. Weather phenomena marked with an asterisk (*) shall be reported immediately using the AWOS manual observation mode for entry and transmission. Because AWOS can only produce observations for longline transmission every 20 minutes, these observations will go out as a METAR, but will

be available for local operations via the oneminute data mode. 2-5. BACKUP REQUIREMENTS a. Situations Requiring Backup. Certified observers are responsible for the completeness and accuracy of the weather observation. If the complete automated observation is unavailable due to sensor/system malfunction, communications failure, and/or non-representative data, backup information shall be provided in accordance with the guidelines in the following subsections. Backup refers to the observer providing the same reporting capability as that provided by the automated weather sensor, consistent with service level standards specified in Appendix D, Service Standards. Backup information is required for long-line dissemination for terminal forecast (TAF) production and for local, groundto-air dissemination to legally sustain local operations at the airport. The “failure” modes mentioned above are defined as follows: (1) Sensor/system Malfunction. One or more sensors or the entire observing system is(are) not reporting data (for any reason). Provide manual backup and make appropriate maintenance notifications. (2) Communications Failure. The automated weather observing system and/or long-line communications are malfunctioning, thereby preventing the entry and/or transmission of the observation over long-line networks. When it is apparent that observations are not being transmitted, relay the observations to the tie-in FSS and notify the appropriate office for outage notification. (3) Non-representative Data. The sensor is reporting data, but the data are incorrect, or the sky condition, visibility and/or

10/18/05 7900.5B

present weather sensor(s) is/are accurately reporting conditions in the vicinity of the sensor, but those conditions are not representative of prevailing conditions for the operating areas of the airport and are considered operationally significant. When this occurs, provide manual backup. Outage notification is not required.

b. Level of Support. The information specified in these guidelines is the minimum required for each of the situations discussed in the following subsections. The FAA may specify additional information beyond this minimum. The observer is encouraged to add any other appropriate remarks. Procedures and practices to provide the required backup information are presented in Chapter 6, Backup Requirements at Automated Weather Stations. c. Communications. Automated weather observing system failure may or may not include loss of long-line communications, local communications, or both. The level of backup information to be provided depends on the status of such communications and whether the information is required for long-line or local, ground-to-air dissemination.

d. Equipment for Backup Observations. Weather observing equipment should be maintained to allow certified observers to perform backup responsibilities in the event of an automated sensor failure. Air Traffic managers shall coordinate with the Service Area Office, local Technical Operations SMO, and the appropriate NWS regional office prior to initiating action to decommission weather observing equipment.

2-6. LONG-LINE BACKUP REQUIREMENTS Details on the procedures to provide backup are in Chapter 6, Backup Requirements at Automated Weather Stations. This paragraph specifies the type of minimum backup for various types of facilities. a. LAWRS Towers. At LAWRS towers, certified air traffic control specialists (ATCS) shall provide the backup information for long-line transmission which is listed in this section. The required information shall be entered into the automated weather observing system via the operator interface device. The following information shall be provided at a minimum: (1) Wind (2) Visibility to 10 miles (3) Present weather and obstructions to vision (see Figure 6-6 for required elements) (4) Sky condition to 12,000 feet (5) Temperature/Dew Point (6) Altimeter setting (7) Required remarks and operationally significant remarks as deemed appropriate (Note: Precipitation of unknown form may be reported only if the automated sensor is operational and is reporting precipitation of unknown form. However, if the observer can determine the type of precipitation, it should be reported using the allowable elements listed in Figure 6-6, Backup and Augmentation Weather and Obscurations.)

7900.5B 5/11/01

b. Non-LAWRS Towers with a Surface-Based Observer. At non-LAWRS towers with a surface-based observer, the surface-based observer shall provide at a minimum the backup information for long-line transmission according to the requirements contained in the Service Standards for the service level of the airport. Backup shall also include required remarks and operationally significant remarks as deemed appropriate by the observer. At these facilities, tower personnel shall routinely provide tower visibility information to the surface-based observer as required. c. Non-Towered Facilities with a Surface-Based Observer. At all non-towered facilities, the surface-based observer shall provide the backup information required by the Service Standards for the service level of the airport. At all facilities with an operator interface device, the required information shall be entered into the automated weather observing system via the operator interface device. Backup shall also include required remarks and operationally significant remarks as deemed appropriate by the observer. 2-7. CERTIFICATION OF PERSONNEL AND CURRENCY REQUIREMENTS Prior to assuming full responsibility for taking any type of surface observation or any part thereof, each person shall be certified. The NWS is responsible for certifying all civilian weather observers in one or more of the following observer types: a. NWS and FAA observers b. LAWRS observer c. Tower visibility observer

d. SAWRS observer e. A-paid observer

Definitions of these types are presented in paragraph 4-2, Definitions. Currency requirements are in Order 3120.4, Air Traffic Technical Training. 2-8. TYPES AND CONTENT OF METAR/SPECI OBSERVATIONS The METAR is the primary code format used in the United States to satisfy requirements for reporting surface meteorological data. The METAR may be prepared by automated weather observing systems (with or without augmentation) or by certified weather observers. These data are primarily reported in an alphanumeric coded format for aviation users. A complete METAR contains the type of report, station identifier, date/time of observation, and whether the report is automated (AUTO) or corrected (COR). Weather phenomena in the METAR include wind, visibility, runway visual range (RVR) (at designated sites), present weather, sky condition, temperature, dew point, and altimeter setting (collectively referred to as “the body of the report”). In addition, significant information elaborating on data reported in the body of the report, or coded and plain language data not included in the body of the report, may be appended to the report in a section referred to as “remarks.” However, the content varies according to the type of weather station and the automated weather observing system used. (See Figure 15-1, Content of METAR/SPECI.) Many parts of the remarks section are not required at FAA facilities. The METAR is a scheduled observation. At manual stations, it is taken between 45 and 59 minutes past the hour. METARs are scheduled on the hour at ASOS sites and every 20 minutes at AWOS sites starting at H+00. A SPECI is an unscheduled

5/11/01 7900.5B

observation taken when there is a significant change in the observation since the previous METAR observation was taken or if an aircraft mishap has occurred. If an aircraft mishap occurs close to a scheduled METAR, then it would be transmitted as a METAR. SPECI criteria are applicable only to stations that have the capability of evaluating the event. If it is time for a METAR to be issued, and SPECI observation criteria are met, the observation will remain designated as a METAR. SPECI observations are not issued at AWOS sites because METARs are issued every 20 minutes. (There are some rare exceptions to this rule.) The criteria for taking SPECI observations are given in Chapter 7, General Procedures for

Manual Observations. Figure 2-1, Guide to Contents of Automated and Manual Aviation Routine Weather Reports (METAR) and Aviation Selected Special Weather (SPECI) Observations, summarizes the weather elements that are available at automated observing systems with precipitation discrimination capability (AO2), and those without precipitation discrimination capability (AO1). The precipitation discrimination capability indicator, AO1 or AO2, is included in the remarks section of the applicable METAR or SPECI report. This figure also shows the additional elements that are available when an observer is present to add information that is beyond the capabilities of the automated observing system (augmentation).

7900.5B 5/11/01

Element of METAR/SPECI Report(s)

Type of Station:

AO1

Augmented

AO1

AO2

Augmented

AO2

Manual Type of Observation: M S1 M S1 M S1 M S1 M S Type of Report X X X X X X X X Station Identifier X X X X X X X X Date/Time X X X X X X X X Report Modifier (AUTO or COR) X X X X4 X4 X4 X4 Wind Direction, Speed, Character X X X X X X X X Visibility X X X X X X X X Runway Visual Range D D D D D Present Weather2 D X X X X X X Sky Condition ≤ 12,000 feet > 12,000 feet

X

X

X

X

X D

X D

X X

X X Temperature X X X X X X X X Dew Point X X X X X X X X Altimeter Setting X X X X X X X X Remarks: Group 1 - Automated, Manual, and Plain Language

Volcanic Eruptions X X X X X Tornadic Activity X X X X X Type of Automated Station (AO1, AO2)

X X X X X X

Peak Wind X X X X X Wind Shift X X X X X X Tower or Surface Visibility D D D D D D D D Variable Prevailing Visibility X X X X X X X X Sector Visibility X D D X X Visibility at Second Location D D D D D D Lightning X D D D D X X Time of Beginning/Ending of Precipitation

X X X5 D X5

Time of Beginning/Ending of Thunderstorms

X3 X3 X X X X

Thunderstorm Location X X X X X AO1 - Automated station does not have precipitation discrimination capability AO2 - Automated station has precipitation discrimination capability AUTO - Appears in weather report of automated system when observer is not logged on M - METAR S - SPECI X - Indicates elements included at all stations D - Indicates elements included only at designated stations Footnote 1: All hourly reports are METAR, all others are SPECIs except AWOS which are all METAR. Footnote 2: Automated stations report only a limited set of present weather and obstruction to vision elements. Footnote 3: ALDARs sites only. Footnote 4: “COR” only. Footnote 5: Report if precipitation caused the SPECI.

Figure 2-1. Guide to Contents of Automated and Manual Aviation Routine Weather Reports (METAR)

and Aviation Selected Special Weather (SPECI) Observations (continued on next page)

5/11/01 7900.5B

Page 13 (and 14)

Element of METAR/SPECI Report(s)

Type of Station:

AO1

Augmented

AO1

AO2

Augmented

AO2

Manual Type of Observation: M S M S1 M S1 M S1 M S Hailstone Size X D D X X Virga X X X X X Variable Ceiling Height X X X X X X X X Obscurations2 D D X X Variable Sky Condition D D X X Significant Cloud Types D D X X Ceiling Height at Second Location D D D D D Pressure Rising/Falling Rapidly D D X X X Sea-level Pressure X X X X D Aircraft Mishap X X X X X No SPECI Reports Taken D Snow Increasingly Rapidly D D D X Other Significant Information D D D D D Remarks: Group 2 - Additive and Automated Maintenance Data

Hourly Precipitation Amount D D X X Ice Accretion X X X X 3-6 Hour Precipitation Amount3 D D X X D 24-Hour Precipitation D D X X D Depth of Snow on Ground D D D Water Equivalent of Snow on Ground D Cloud Types Duration of Sunshine Hourly Temperature and Dew Point X X D 6-Hourly Maximum Temperature D D X X D 6-Hourly Minimum Temperature D D X X D 24-Hour Max/Min Temperature D D X X D 3-Hourly Pressure Tendency X X D Sensor Status Indicators X X X X Maintenance Indicator X X X X AO1 - Automated station does not have precipitation discrimination capability AO2 - Automated station has precipitation discrimination capability AUTO - Appears in weather report of automated system when observer is not logged on M - METAR S - SPECI X - Indicates elements included at all stations D - Indicates elements included only at designated stations Footnote 1: All hourly reports are METAR, all others are SPECIs except AWOS which are all METAR. Footnote 2: Automated stations report only a limited set of present weather and obstruction to vision elements. Footnote 3: 3-Hour precipitation amounts required at designated stations only.

Figure 2-1. Guide to Contents of Automated and Manual Aviation Routine Weather Reports (METAR)

and Aviation Selected Special Weather (SPECI) Observations (concluded from previous page)

5/11/01 7900.5B

CHAPTER 3. GENERAL PROCEDURES 3-1. INTRODUCTION This chapter prescribes procedures and practices applicable to all facilities and to all types of observations. 3-2. DEFINITIONS a. Aircraft Mishap. Aircraft mishap is an inclusive term to denote the occurrence of an aircraft accident or incident. b. Coordinated Universal Time (UTC). UTC is the time in the zero degree meridian time zone, also commonly known as Zulu (Z) time. c. Local Standard Time (LST). LST is a time based on the geographic location of the facility in one of the legally established time zones of the globe. d. Standard Time of Observation. The standard time of observation is the hour to which a METAR observation applies. e. Aviation Routine Weather Report (METAR). A METAR is a measurement or evaluation of meteorological elements that describe the state of the atmosphere at the surface location(s) where the observation is taken. METAR is a scheduled observation. f. Aviation Selected Special Weather Report (SPECI). A SPECI is a weather observation that is reported at other than a scheduled time. SPECI shall be taken when any of the criteria for a special observation is observed or detected.

fCHAPTER 3.pdf

3-3. AVIATION WEATHER OBSERVING LOCATIONS Surface weather observation locations shall make routine reports at fixed intervals (METAR reports). Where the capability exists, the routine reports shall be supplemented by non-routine reports (SPECI). The observing location is defined as the point or points at which the various elements are observed. In cases where all the measurements are taken at the same point, an observation will be regarded as having a single location. In cases where the various sensors are located to obtain acceptable exposure, the observation location will be regarded as varying with the individual elements in an observation. Normally, multiple observing points are confined to an area within about 2 miles of the station. Weather reports from manual stations may also contain information on phenomena occurring at other than the location of the observation. For example, at a large airport the observation location may be defined as follows: a. For elements such as clouds, prevailing visibility, present weather, and obscurations, the observing location may be coincident with the observer's physical location or it may be the touchdown area of the primary runway. b. For temperature, dew point, and wind, the observing location may be the center of the runway complex. c. For cloud height and ceiling, the observing location may be a point near the approach end of a runway.

7900.5B 5/11/01

d. For the location of lightning, the observing point may be the Airport Reference Point (ARP). The ARP is a permanent airport reference point defined by a latitude/longitude. e. For tower visibility, the observing location shall be the Airport Traffic Control Tower (ATCT). (NA LAWRS) f. Regardless of observing location or the locations of the sensors, there shall be only one observation disseminated long-line for an airport. If applicable, a report from a commissioned ASOS shall be designated as the weather observation for that airport. A report from a commissioned AWOS may also be designated as the weather observation for an airport. When the air traffic control facility is not in operation, these systems will be operated in the fully automated mode as the weather observation source. 3-4. GENERAL OBSERVING PRACTICES The general observing practices specified in the following subsections apply to personnel taking either full manual, augmented, backup, or tower visibility observations. They do not necessarily apply to the automated portions of observations, which are controlled by system software. a. Order of Observing. Elements having the greatest rate of change shall be evaluated last. When conditions are relatively unchanging, the observer shall evaluate the elements outdoors first, and then evaluate the elements indoors, with pressure being the last element evaluated. b. Recency of Observed Elements. Individual elements entered in an observation shall, as closely as possible, reflect conditions existing at the actual time of observation. At manual locations, elements entered shall have been observed within 15 minutes of the actual

time of observation. Gusts and squalls shall be reported if observed within 10 minutes of the actual time of observation. METAR observations shall be made as close to the scheduled time of the observation as possible to meet filing deadlines, but in no case shall these observations be started more than 15 minutes before the scheduled time. c. Dark Adaptation. When taking observations outdoors at night, sufficient time should be allowed for the observer's eyes to become adjusted to the darkness. d. Weather Not Observed. Observers are not required to report occurrences they have not observed. However, the observer may use information from reliable sources, for example, pilots, airline/airport personnel or other sources deemed acceptable by the observer. e. Time Disseminated in Reports. All times shall refer to the 24-hour clock, for example, 1:47 a.m. shall be referred to as 0147; 1:47 p.m. shall be referred to as 1347. The times 0000 and 2359 shall be used to indicate the beginning and ending of the day, respectively. f. Time Standards. Times used in weather observations shall be: (1) Local Standard Time (LST). (NA LAWRS). LST is used on MF1M-10Cs to record times of observation and time checks. LST shall be entered on all forms throughout the year with no consideration of daylight savings time. (2) Coordinated Universal Time (UTC). UTC is used on all transmitted data. It is also used on MF1M-10Cs to record times of observations and time checks at LAWRS sites.

5/11/01 7900.5B

g. Accuracy of Time in Observations. The accuracy of the actual time of observation and time checks on recording charts is very important in aviation safety investigations. One clock shall be designated as the observing location standard, and a routine procedure set up to assure its accuracy once a day at a minimum. The clock used shall be within ± 1 minute of the U.S. Naval Observatory Time. If available, the FAA Coded Time Source (CTS) may be substituted for U.S. Naval Observatory Time. 3-5. DISSEMINATION For purposes of this order, dissemination is the act of delivering a completed report to users. There are two general types of dissemination. a. Local. Local transmission is the transmission or delivery of a weather report to individuals or groups of users in the service area of the observing location. b. Long-line. Long-line transmission is the transmission of a weather report beyond the service area of the observing location. 3-6. DISSEMINATION REQUIREMENTS All reports shall be given local dissemination. At designated stations, reports shall be given long-line dissemination. When reports are corrected, the corrected report shall be given the same dissemination as the report being corrected. If reports cannot be disseminated simultaneously, local and long-line, they shall be disseminated first to the local airport traffic control users, then disseminated long-line. SPECI observations shall be completed and transmitted as soon as possible after conditions meeting SPECI criteria are observed or detected. A METAR shall be transmitted in accordance with agency guidelines. A METAR entered that also meets the criteria for a SPECI shall be disseminated as a

METAR. WS Form B-11, METAR/SPECI Report for Transmission, is available from the NWS for those facilities that receive manual observations from observers over the phone. This form is an optional aid for transcribing the observation for transmission. (See Appendix F, METAR/SPECI Report for Transmission.) 3-7. CORRECTIONS TO TRANSMITTED DATA Once an error has been detected in a transmitted report, a correction shall be transmitted as soon as possible. Do not transmit a correction if the original transmitted observation has been superseded by a later report. Transmit the entire corrected report with (COR) as the report designator. Use the original date and time of the report being corrected. 3-8. DELAYED REPORTS When transmission of a manual observation is delayed until time for the next regularly scheduled report, only the latest report shall be transmitted. In the record of observations, the remark Filed But Impractical to Transmit (FIBI) shall be appended in parentheses to the report that was not transmitted. The remark FIBI shall not be included in any local dissemination of the report. When a SPECI is not transmitted longline, later SPECIs shall be transmitted long-line only when the overall change between the last transmitted report and the current report satisfies the criteria for a SPECI. If the SPECI is not transmitted long-line, the remark FIBI shall be appended to the report as described above. All SPECI reports shall be disseminated locally. Reports of volcanic eruption shall be disseminated, by any means possible, regardless of the delay.

7900.5B 5/11/01

3-9. ROUNDING OFF NUMBERS Except where otherwise designated in this order, when computations require that a number be rounded, if the fractional part of a positive number to be dropped is equal to or greater than one-half, the preceding digit shall be increased by one. If the fractional part of a negative number to be dropped is greater than one-half, the preceding digit shall be decreased by one. In all other cases, the preceding digit shall remain unchanged. For example, 1.5 becomes 2, 1.3 becomes 1, -1.5 becomes -1, and -2.6 becomes -3. Refer to paragraph 14-21, Rounding Pressure Values, for rounding of pressure values. 3-10. RECORD KEEPING AND FORMS a. Manual Observations. All manual observations, whether complete or partial, shall be recorded on form MF1M-10C (does not include automated stations). After completing the form, it shall be archived at the facility completing the form. Facilities shall prepare an original and at least one good duplicate copy of each form. The copies shall be legible and suitable for retention and duplication. Corrected copies of all forms shall be retained locally for 90 days. Retention of copies beyond 90 days shall be as directed by the Washington Headquarters. All original forms and the charts from recording instruments shall be mailed to the National Climatic Data Center (NCDC) as follows: (1) By the second working day of each month, mail all MF1M-10Cs for the preceding month, together with all recording charts except those from the ceilometer and transmissometer. (2) To facilitate handling and verification by NCDC, each day's form and

recorder charts shall be placed in chronological order and shall be free of all staples. Mail the original forms and recorder charts to: NCDC Services Center Image Entry 465 Industrial Blvd. London, KY 40741 b. Automated Weather Observations. Automated weather observations and operator terminal entries are archived on site. No further action is required by FAA, FAA-contract or NF-OBS facilities. In the event of a complete failure of automated equipment, observers are expected to follow manual observation recording requirements. 3-11. EVALUATING WEATHER SENSOR ACCURACY a. Sensor Evaluations. When the observer has reason to believe that the accuracy or validity of indications from meteorological sensors is questionable, the use of such equipment should be discontinued until necessary corrective maintenance has been accomplished. If the use of such equipment is discontinued, any required back-up procedures or practices shall be initiated. FAA personnel and NF-OBS providers shall make appropriate maintenance notifications in the event of any equipment outages. If the observer believes that the ASOS information is inaccurate, they should notify the ASOS Operations and Monitoring Center (AOMC). b. Notices to Airmen (NOTAMS). The FSS/AFSS shall accept, categorize, and distribute Notices to Airmen (NOTAMs) on all systems and system components in accordance with the instructions contained in Order 7930.2.

10/18/05 7900.5B

c. Time Entries on Recorder Charts. Time entries (such as those for time checks) on recorder charts shall be made to the nearest minute LST, except at LAWRS sites, where UTC time is entered. d. Time Checks on Recorder Charts. Time checks on the recorder chart of recordingtype instruments shall be made as follows: (1) At the beginning and end of each chart roll. (2) When notified of an aircraft mishap. (3) For each disruption or discontinuity in the trace; e.g., upon return of equipment to service following an outage or periodic maintenance. (4) At the time of the first observation at facilities not operating 24 hours per day. e. Time Adjustments on Recorder Charts. When a recorder is adjusted to the correct time, the observer shall indicate the adjustment on the chart by entering an arrow at the point of the adjustment and writing the time of the adjustment near the arrow.

f. Power and Equipment Failures. The observer shall indicate power and equipment failures on recording-type instruments by entering on the recorder chart at the point of the failure the term POWER FAILURE or EQUIPMENT FAILURE and the time of the failure. When the equipment is returned to service, the observer shall, if necessary, adjust the chart to the correct time and enter a time check. 3-12. DOCUMENTATION OF OBSERVING LOCATION AND FACILITIES An accurate Station Information File shall be maintained at the FAA service area office. This file shall document the equipment (including automated weather observing systems equipment), instrumentation, and the observing program at the facility. The file shall contain, as a minimum, the information specified in the FMH-1 (see Figure 3-1). It is each service area office’s responsibility to ensure that a copy of the Station Information File for each observing location is sent to the National Climatic Data Center (NCDC), Attn: Code EF1100, of the National Oceanic and Atmospheric Administration (NOAA). A copy of the file shall be sent when a station is established, when any data listed in the file changes or is corrected, and when a station closes. This file shall become a part of that station’s archived record.

7900.5B 5/11/01

Physical Characteristics Station Name Airport Name Station Identifier WMO Index Number Time Zone

Latitude/Longitude Climatological Elevation Field Elevation Ground Elevation Station Elevation

Type of Station Description of Significant Topography

Observation Schedule Types of Reports

Schedule for Reports

Hours of Operation

Observation Program Elements Observed Long-Line Communications Circuits

SPECI Transmitted (Y/N)

Sensor Data System Configuration Types of Sensors

Location of Sensors

Non-standard Sensor Siting

Figure 3-1. Station Information File

gCHAPTER 4.pdf

5/11/01 7900.5B

CHAPTER 4. GENERAL PROCEDURES AT AUTOMATED WEATHER

STATIONS 4-1. PURPOSE This chapter prescribes procedures and practices to be followed by personnel responsible for manually observing, reporting and/or transmitting surface weather information required for augmentation, and/or for sustaining minimum operations in the event of partial or total failure of the automated weather observing system. This chapter also describes specific differences in these procedures and practices applicable to LAWRS observers. 4-2. DEFINITIONS a. Observer. The generic term "observer" applies to a number of different types of personnel with various responsibilities for providing weather information. These various types are: (1) Weather Observer. A person who is certified by the NWS to provide a designated range of weather observation elements. These include NWS, NWS-contract, FAA and FAA-contract personnel. (a) LAWRS Observer. An NWS-certified air traffic control specialist (ATCS) with weather observation responsibilities for surface aviation weather elements. (b) Tower Visibility Observer. An ATCS certified by NWS to observe and report airport visibility from the control tower. (2) A-Paid Observer. Contract weather observers who take only hourly observations (METAR). They are certified by

NWS to provide weather information under the terms of a "per-observation" agreement.

(3) NF-OBS Observer. A nonfederal observer working under the guidelines of the NF-OBS program, providing backup and augmentation of the ASOS. b. Surface Weather Observing Stations (1) Automated Station. A facility with an automated weather observing system that prepares the observation for transmission with no certified observer signed on to the system. (a) Augmentation. The manual addition of data to an automated observation which is beyond the capabilities of the automated weather observing system. (b) Backup. An alternative method of providing the weather observation when any portion of the automated observation is unavailable or erroneous due to sensor/system malfunction, communications failure and/or nonrepresentative data. (2) Manual Station. A facility where certified weather observers are responsible for observing, evaluating, and processing the surface aviation observation. At these facilities, various types of automated weather observing systems, sensors and/or other automated equipment may be available. (3) NF-OBS Program. A program whereby a local entity such as a non-federal

7900.5B 5/11/01

control tower (NFCT), airport personnel or fixed-based operator (FBO) may assist, at no cost to the Government, with the augmentation or backup of the automated weather observing system. Observers must be certified by NWS. 4-3. TYPES OF AUTOMATED STATIONS a. FAA, FAA-contract and NF-OBS Stations. There are two major classes of automated surface weather observing systems used at FAA, FAA-contract and NF-OBS sites: ASOS and AWOS. The augmentation and backup of these systems are described in the next two chapters for all FAA, FAA-contract and NF-OBS site personnel. (1) Automated Surface Observing System (ASOS). ASOS is a type of automated surface weather observing system developed through a joint FAA/NWS/DOD agreement. FAA ASOSs are installed at designated airports and maintained by the NWS to meet FAA requirements. There are three configurations of ASOS. The first contains at least one of each of the following sensors:

(a) Wind sensor.

(b) Visibility sensor.

(c) Precipitation identification sensor. (d) Cloud height indicator sensor. (e) Temperature and dew point sensors. (f) Pressure sensors.

(g) Precipitation accumulation sensor. (2) The second ASOS configuration has a freezing precipitation sensor in addition to

all of the above sensors. The third configuration has a thunderstorm/lightning sensor. Systems without individual lightning sensors will get thunderstorm reporting via the Automated Lightning Detection and Reporting System (ALDARS). Many sites have an ASOS/ATIS Interface Unit (AAIU), which provides the capability to broadcast current weather from the ASOS over the ATIS ground-to-air radio when the tower is closed. ASOS may also have an interface to New Generation RVR equipment. See Chapter 10, Runway Visual Range. (3) Automated Weather Observing System (AWOS). AWOS is a type of automated surface weather observing system certified and commissioned by the FAA. The AWOS was developed under a Flight Standards Service-sponsored project specifically to provide weather information at locations without previous weather observation capabilities. There are eight types of AWOS, namely, A, 1, 2, 3, 3P, 3T, 3P/T, and 4. (a) AWOS-A: AWOS-A contains only dual-pressure sensors that measure pressure and report altimeter setting to the pilot. (b) AWOS-1: AWOS-1 contains the AWOS-A sensors plus sensors to measure wind data (speed, direction, and gusts), temperature, and dew point, and to report density altitude. (c) AWOS-2: AWOS-2 contains all the AWOS-1 sensors, plus a visibility sensor. (d) AWOS-3: AWOS-3 contains all the AWOS-2 sensors, plus a cloud height sensor.

5/11/01 7900.5B

(e) AWOS-3P: AWOS-3P contains all the AWOS-3 sensors, plus a precipitation identification sensor. (f) AWOS-3T: AWOS-3T contains all the AWOS-3 sensors, plus a thunderstorm/lightning reporting capability. (g) AWOS-3P/T: AWOS-3P/T contains all the AWOS-3 sensors plus a precipitation identification sensor and a thunderstorm/lightning reporting capability. (h) AWOS-4: AWOS-4 contains all the AWOS-3 sensors, plus precipitation occurrence, type and accumulation; freezing rain; thunderstorm; and runway surface condition sensors. (4) Many AWOSs were installed at airports without previous weather observations, so personnel may not be available to augment or back up the automated weather observations. The most common type of AWOS observation is the AWOS-3. It is identified by AUTO (automated report) in the body of the report and AO1 (automated station without precipitation discriminator) in the remarks section if it is a fully automated report. If it is being augmented/ backed up by an observer, it will not have AUTO in the body of the report and it will have AO1 in the remarks section. (See examples in Figure 5-2, Examples of Augmented Observations.) b. Non-FAA Stations. In addition to the systems described above, there are various NWS, DOD and non-federal automated weather observing systems. All non-federal automated weather observing systems to be used for aviation must be certified and commissioned by the FAA in accordance with the most current version of FAA Advisory Circular

AC 150/5220-16, Automated Weather Observing Systems (AWOS) for Non-Federal Applications. 4-4. CERTIFICATION All FAA and contract personnel, including LAWRS personnel, responsible for providing weather observations, augmentation information, tower visibility observations or backup weather information shall be certified at least to the level commensurate with current duties. Certification shall be in accordance with the provisions of paragraph 2-7, Certification of Personnel. 4-5. GENERAL PROCEDURES At automated weather observing locations, the specified weather information shall be taken, recorded and disseminated in accordance with the procedures and practices in this order. Operator procedures for recording and disseminating augmentation and backup information are summarized in Figure 4-1, Operator Procedures for Providing Augmentation and Backup Information. Weather information taken and reported should reflect only those conditions seen, or reported by a reliable source, from the usual point of observation and, unless otherwise specified, must have occurred at the time of the observation. 4-6. GENERAL EQUIPMENT PROCEDURES General equipment operating instructions to perform the duties associated with automated weather observing systems are contained in the following publications: a. For all federal and non-federal AWOS systems manufactured by Qualimetrics, Inc., the AWOS Operator Instructions.

7900.5B 10/18/05

b. For non-federal AWOS systems manufactured by AAI/SMI, Inc.; Vaisala Inc., Handar Business Unit; the appropriate AWOS user manual as approved by the FAA. c. For ASOS, the ASOS Software User’s Manual or Ready Reference Guide. d. For future automated weather observing systems as may be approved by the FAA, the appropriate operations manual or quick reference guide. 4-7. PROCEDURES AT NON-FEDERAL OBSERVATION (NF-OBS) SITES Upon request from a non-federal entity, a written agreement to provide augmentation and backup of the ASOS at a commissioned ASOS site will be executed between the Service Area Office and the NF-OBS provider. The agreement shall be site-specific and shall contain the hours and the service level at which service will be provided. The minimum level of augmentation shall be the FAA-validated aviation service standard level for that site. Service may be provided at a higher level; however the NF-OBS provider must provide that higher level during all hours of operation. As Service Level D is a stand alone ASOS site, NF-OBS providers operating at these sites shall provide a minimum of level C service. 4-8. PROCEDURES AT NON-FEDERAL AWOS SITES FAA facilities shall negotiate a letter of agreement (LOA) with the airport management or appropriate authority at locations where a nonfederal AWOS is installed at an airport with an operating control tower. The LOA shall define responsibilities, equipment and coordination requirements, identify special operating conditions, and define local requirements. ATCSs may disseminate only those non-federal weather

observations that are obtained through the weather message switching center or other equivalent documented means. Pilots who want non-federal AWOS information from sites that do not include automatic long-line dissemination should be provided the appropriate frequency and/or telephone number, if known. 4-9. PROCEDURES FOR HANDLING AIRCRAFT MISHAPS AT AUTOMATED SITES The requirement to record the present weather following an aircraft mishap remains valid at automated sites. At a minimum, a mishap requires weather data from 1 hour before to 1 hour after the mishap occurs. ASOS observations should be archived by the observer or by calling the ASOS Operations and Monitoring Center (AOMC) (1-800-242-8194). The AOMC has the capability to archive the 5-minute observations from the previous 12 hours of weather observation data from attended and unattended locations. The supervisor or controller-in-charge shall ensure that the 5-minute observations are archived following notification of an aircraft mishap at a location where an ASOS is operational. AOMC requests must be made within 10 hours of the incident. Archive AWOS data in accordance with the procedures in the AWOS Operator Instructions or by calling the AWOS Central Monitoring Center at 1-800-322-0433 or 801-320-2184. 4-10. GENERAL REQUIREMENTS FOR RECORD KEEPING Automated weather observation data and operator terminal entries are archived on site. No further action is required by

5/11/01 7900.5B

FAA, FAA-contract or NF-OBS facilities. If the automated weather observing system is completely inoperative, follow the recordkeeping procedures for manual stations.

7900.5B 5/11/01

OPERATOR PROCEDURES FOR AUGMENTATION AND BACKUP INFORMATION

CONDITION LONG-LINE LOCAL

AWOS w/o Operator Terminal

AUGMENTATION not possible local procedures

BACKUP INFORMATION:

Sensor Failure Manual observation provided to

designated office

local procedures

OT/communications failure Manual observation provided to

designated office

local procedures

Erroneous/Non-representative data Manual observation provided to

designated office

local procedures

AWOS with Operator Terminal

AUGMENTATION Mode 31 Mode 3

BACKUP INFORMATION:

Sensor Failure Mode 3/42 Mode 3/4

OT/communications failure Manual observation provided to

designated office

local procedures

Erroneous/Non-representative data Mode 4 Mode 4

ASOS (all locations)

AUGMENTATION Enter data via OID Enter data via OID

BACKUP INFORMATION:

Sensor Failure Edit data via OID Edit data via OID

OID/communications failure Provide to designated office3 Local procedures

Erroneous/Non-representative data Edit data via OID Edit data via OID

LEGEND: OID/OT - any automated weather observing system operator interface device FOOTNOTES: 1. Enter augmentation in remarks preceded by the code, “WEA:”. 2. Enter the complete observation manually via OT. Partial editing is not possible. 3. Any available communication may be used (For non-LAWRS towers, information is provided only if requested).

Figure 4-1. Operator Procedures for Providing Augmentation

and Backup Information

5/11/01 7900.5B

Page 27 (thru 28)

4-11. - 4-12. RESERVED

hCHAPTER 5w table fix.pdf

5/11/01 7900.5B

CHAPTER 5. AUGMENTATION AT AUTOMATED WEATHER STATIONS 5-1. INTRODUCTION This chapter prescribes procedures and practices applicable to the augmentation of automated surface observations at all FAA, FAA-contract and NF-OBS facilities. In addition, this chapter also prescribes specific differences in augmentation procedures and practices applicable to LAWRS observers, as well as tower visibility requirements. FAA guidelines applicable to the augmentation of automated surface observations are presented in paragraph 2-3, General Types of Observations. Figure 5-1, Summary of FAA Augmentation Requirements, summarizes the minimum augmentation requirements by type of facility, which were given previously in Chapter 2, Guidelines. 5-2. VALIDITY OF DATA Once an observation has been augmented, the observer shall ensure the validity of the augmented data by deleting or changing the data as required. 5-3. SIGN ON/SIGN OFF THE AUTOMATED WEATHER OBSERVING SYSTEMS In order to enter augmentation data into the automated weather observing system, the observer must be signed on. Sign on shall be in accordance with the respective automated weather observing system’s operator handbook or locally prescribed procedures. The “AUTO” tag at the beginning of the observation will be dropped when the observer signs on.

a. Sign On/Sign Off the ASOS. (1) When using ASOS, several augmented events (e.g., tornadic activity, thunderstorm, or hail) automatically generate SPECI observations for the beginning and ending of the event. If one of these events is occurring at the close of augmentation coverage, it will be necessary to end the event or it will continue to be reported during the hours when there is no augmentation coverage. The observer shall end the event immediately after the last hourly METAR is transmitted before going off duty. The ending of the event will automatically generate a SPECI. The observer shall cancel this SPECI, enter the AUTO REMARK and disable the present weather (PREWX). The observer shall then sign off the automated weather observing system. This procedure will end the erroneous ending remark in the next observation. (2) Virga and volcanic ash are events that do not generate SPECIs. Virga is automatically deleted from the observation after the hourly METAR is transmitted. If virga continues to occur, it shall be re-entered. If volcanic ash is occurring at the close of augmentation coverage, it will be necessary to end the event or it will continue to be reported during the hours when there is no augmentation coverage. The observer shall end the event immediately after the last hourly METAR is transmitted before going off duty.

7900.5B 5/11/01

Figure 5-1. Summary of FAA Augmentation Requirements

SUMMARY OF FAA AUGMENTATION REQUIREMENTS

TOWERED

with ASOS

NON- TOWERED with

ASOS

AWOS4

with

TOWERED

w/ AWOS4

ELEMENT

W/O OBS1

W/ OBS2

FSS3

or FAA Contract

OBS w/o OBS

Thunderstorm T O F O T

Tornadic Activity5 T O F O T

Hail T O F O T

Virga T O F O T

Volcanic ash T O F O T

Weather6 NA7 NA7 NA7 O T

Tower Vsby T8 T9

Footnotes: 1. Towered site without a surface-based observer. (LAWRS) 2. Towered site with a surface-based observer. 3. FSS where the FAA was responsible for observation prior to automated system. As long as thunderstorm augmentation is required, other elements shall be provided if the capability to provide them exists. 4. At sites that have an operator terminal. 5. Includes tornado, waterspout, and funnel cloud. 6. Weather and obstructions to vision. See Figure 6-6 for complete list of required elements. 7. Weather is considered a backup requirement for ASOS. 8. Tower visibility either provided to observer for input or entered via operator interface device. 9. At sites with tower. Legend: Blank - Augmentation not provided F - Augmentation provided by certified FSS observer or FAA-contract observer O - Augmentation provided by surface-based observer T - Augmentation provided by certified tower observer OBS - Surface observer

5/11/01 7900.5B

b. Sign On/Sign Off the AWOS. At AWOS sites, the observer shall sign on/sign off the automated weather observing system following the procedures stated in the AWOS Operator’s Instructions. 5-4. ORDER FOR REPORTING WEATHER AND OBSTRUCTIONS TO VISIBILITY See Figure 15-1, Content of METAR/SPECI, and Figure 15-2, METAR or SPECI Code Format, in Chapter 15, Coding and Dissemination. 5-5. AUGMENTATION OBSERVING PROCEDURES Except as specified in the following subsections, observing procedures for augmentation shall be the same as specified for the corresponding manual observation in chapters 7 through 14. Figure D-1, Service Standard Levels, shows elements to be augmented for each service level. a. Observing Tornadic Activity. The term tornadic activity shall include funnel clouds, tornadoes, and waterspouts. Observing procedures for tornadic activity are given in paragraph 11-29, Tornado, Waterspout, or Funnel Cloud. A funnel cloud, tornado, or waterspout is considered to begin at the time it is observed by the observer. A funnel cloud, tornado, or waterspout is considered to end at the time it disappears from sight. b. Observing Thunderstorms. Observing procedures for thunderstorms are given in paragraph 11-30, Reporting Thunderstorms, and paragraph 11-31, Beginning and/or Ending of a Thunderstorm. A thunderstorm occurrence begins when thunder is first heard, lightning is observed over the station and the local noise level is sufficient to prevent hearing thunder, or

when lightning is detected by an automated sensor within ten miles of the airport. A thunderstorm is considered to end 15 minutes after the last occurrence of any of these criteria. c. Observing Hail. Observing procedures for hail are given in paragraph 11-32, Reporting Hail. Hail begins at the time it is first observed and ends when it is no longer falling. No intensity shall be assigned to hail, i.e., the observer shall not characterize hail as light, moderate, or heavy. d. Observing Volcanic Ash. Observing procedures for volcanic ash are given in paragraph 11-39, Special Procedures for Volcanic Ash. The observer shall report volcanic ash whenever it is observed at the station. e. Observing Virga. Virga is defined as precipitation falling from clouds but not reaching the ground. The observer shall report virga when observed. Virga is not considered to be present weather or an obscuration. f. Observing Tower Visibility. Observing procedures for tower visibility are given in paragraph 9-3, Visibility Standards. 5-6. REPORTING PROCEDURES a. General Reporting Procedures. General operator procedures for recording and disseminating augmentation information are summarized in Figure 4-1, Operator Procedures for Providing Augmentation and Backup Information. (1) ASOS. At ASOS sites, report tornadic activity (to include funnel clouds, tornadoes, or waterspouts), thunderstorm, hail, volcanic ash, virga or tower visibility by making the appropriate entry on the operator's interface

7900.5B 5/11/01

device in accordance with procedures in the ASOS Ready Reference Guide. (2) AWOS. At AWOS sites, all augmentation reports shall be made in the remarks of the report and shall be prefixed with the phrase WEA:. The reports shall be entered in accordance with procedures prescribed in the appropriate AWOS Operator’s Instructions or FAA-approved manufacturer's equipment manual. b. Reporting Procedures for Each Weather Observation Element. (1) Reporting Tornadic Activity. The term tornadic activity shall include funnel clouds, tornadoes, and waterspouts. These phenomena shall be reported in a SPECI observation whenever they are observed or disappear from sight. At ASOS sites, the event will continue to be reported automatically until the observer deletes the entry. (2) Reporting Thunderstorms. At ASOS sites, entry or deletion of a thunderstorm report shall be made. The event will continue to be reported automatically until the observer deletes the entry. A SPECI observation is generated automatically for the beginning and ending times of thunderstorms. A thunderstorm occurrence begins when thunder is first heard, when lightning is observed at the station and the local noise level is sufficient to prevent hearing thunder, or when lightning is detected by an automated sensor within ten miles of the airport. Location and direction of movement of the thunderstorm, and the location, type, and frequency of lightning should be reported, if known. LAWRS personnel are only required to annotate the beginning/ending times of thunderstorms.

(3) Reporting Hail. At ASOS sites, entry or deletion of a hail report shall be made. The event will continue to be reported automatically until the observer deletes the entry. Hail begins when it is first observed and ends when it is no longer falling. No intensity is assigned to hail, i.e., hail shall not be characterized as light or heavy. Hail size should be reported, if known. (4) Reporting Volcanic Ash. VA is the standard contraction used for volcanic ash. It will be reported in the body of the report as an obscuration whenever observed. At ASOS sites, the event will continue to be reported automatically until the observer deletes the entry. A special observation is not required when volcanic ash is observed. No intensity is assigned to volcanic ash, i.e., the observer shall not characterize volcanic ash as light, moderate, or heavy. Remarks are optional, but if the volcanic eruption producing the volcanic ash is observed, it shall be entered in remarks and a special observation shall be generated. (5) Reporting Virga.

When precipitation is observed to be falling from clouds but is not reaching the ground, the observer shall report VIRGA in remarks. There is no standard contraction used for virga. Virga is not considered to be present weather or an obstruction to vision. In remarks, VIRGA is spelled out in full. At ASOS sites, the event will continue to be reported automatically until the observer deletes the entry or until after the next hourly observation. The remark VIRGA will not be automatically kept in remarks of the observation past the next hourly observation. If virga persists, it shall be re-entered as a remark. No SPECI is required when virga is observed. No intensity is assigned to virga, i.e., the observer shall not characterize virga as light, moderate, or

5/11/01 7900.5B

heavy. The direction of the virga from the site is optional. (6) Reporting Tower Visibility (NA LAWRS). At towered ASOS sites with a surface-based observer, a tower visibility report shall be made by notifying the surface-based observer or using the appropriate entry on the operator's interface device. Reporting of tower visibility shall be in accordance with coding and

dissemination procedures specified in paragraph 15-25, Tower or Surface Visibility. 5-7. EXAMPLES OF AUGMENTED OBSERVATIONS Examples of augmented weather observations for a typical condition (i.e. thunderstorm) are given in Figure 5-2, Examples of Augmented Observations, for AWOS and ASOS.

Examples of Augmented Observations AWOS w/o Aug METAR KHEF 011755Z AUTO 21020G35KT 1SM OVC010 27/24 A2991 RMK AO1 AWOS w/ Aug METAR KHEF 011755Z 21020G35KT 1SM +TSRA OVC010CB 27/24 A2991 RMK AO1 WEA:TSRA OCNL LTGCG OHD TS OHD MOV E ASOS w/o Aug METAR KGLD 011755Z AUTO 21020G35KT 1SM +RA OVC010 27/24 A2991 RMK AO2 SLP101 ASOS w/ Aug METAR KBHM 011755Z 21020G35KT 1SM +TSRA OVC010CB 27/24 A2991 RMK AO2 OCNL LTGCG OHD TSB42 TS OHD MOV E SLP101 ASOS w/o Aug with ALDARS METAR KSEG 171753Z AUTO 21020G30KT 1SM TSRA OVC010 27/24 A2991 RMK AO2 LTG DSNT E TSB42 SLP101 ASOS w/ Aug and ALDARS METAR KAOO 011753Z 21020G35KT 1SM TSRA OVC010CB 27/24 A2991 RMK AO2 LTG DSNT E TSB42 TS OHD MOV E SLP101

Figure 5-2. Examples of Augmented Observations

7900.5B 5/11/01

Page 34 (thru 36)

5-8. - 5-9. RESERVED

iCHAPTER 6.pdf

5/11/01 7900.5B

CHAPTER 6. BACKUP REQUIREMENTS AT AUTOMATED WEATHER

STATIONS 6-1. INTRODUCTION This chapter presents the procedures and practices for providing the backup weather information required in the event of a partial or total failure of the automated weather observing system or if one or more of the elements within the automated weather observing system observation are judged to be erroneous or nonrepresentative. Responsible personnel shall provide the backup weather information specified in Chapter 2, Guidelines. Facilities designated to perform augmentation shall also augment during periods when backup is required. 6-2. SUMMARY OF BACKUP REQUIREMENTS Figure 6-1, Summary of Long-line Backup Requirements, presents a summary of the backup weather information requirements to support the pilots’ safety and regulatory requirements and the terminal forecast preparation program of NWS. The figure documents the level of backup required in accordance with the service level standards as described in Appendix D, Service Standards. In addition to the observational elements shown in the figures, the minimum functions of communications and observational records to back up the automated weather

observing systems shall be provided for as specified in this chapter. If a partial system failure or erroneous data involves weather elements not required to be provided in accordance with specifications in this chapter, those elements may be treated as missing. Responsible personnel may disable those automated sensors in accordance with applicable equipment manuals. When reverting to the manual mode, responsible personnel shall record justification for reverting on FAA Form 7230-4, Daily Record of Facility Operation, and shall make appropriate maintenance notifications. (Personnel should also record the observation on the NWS meteorological form.) When long-line communications are unavailable, the FSS/Automated Flight Service Station (AFSS) shall disseminate these reports. Dissemination procedures are outlined in Figure 4-1, Operator Procedures for Providing Augmentation and Backup Information. 6-3. VALIDITY OF DATA Once a weather observation is modified through manual actions, the responsible person shall assess the validity of the data by deleting or changing the observation as required.

7900.5B 5/11/01

SUMMARY OF LONG-LINE MINIMUM BACKUP REQUIREMENTS

TOWERED NON ELEMENT

LAWRS

NON-LAWRS

WITH OBSERVER1

TOWERED

WITH OBSERVER1 Wind T O O Visibility to 10 Miles T O O Present Weather & Obscurations2

T O O

Sky Condition to 12K Ft. T O O Temperature/Dew Point T O O Altimeter Setting T O O Tower Visibility T

Footnotes: 1. Includes all FSS, FAA-Contract and non-federal observers. 2. See Figure 6-6 for required elements. Legend: Blank - Element not provided T - Element provided by certified Air Traffic Control Specialist O - Element provided by surface-based observer

Figure 6-1. Summary of Long-line Backup Requirements 6-4. EQUIPMENT REQUIREMENTS The following are minimum requirements for equipment required to provide the weather information specified in this chapter. Unless stated otherwise, the equipment is required only if that element is required at your facility. References to an "OID/OT" indicate any automated weather observing system operator interface device. a. Equipment for Wind Direction and Speed. If available, the primary low-level wind shear alert system (LLWAS) sensor or other onsite wind equipment shall be used. Otherwise, the wind direction and speed may be estimated during periods when all automated wind sensors are inoperative.

b. Equipment for Visibility. There is no equipment required for automated visibility sensor backup. However, a current list or visibility chart(s) depicting day and night visibility reference points shall be maintained and available at the point of observation for use at each facility. c. Equipment for Present Weather and Obstructions to Vision. Visual procedures shall be used to identify the type(s) of present weather and/or obscurations. If necessary, visual procedures shall be used to determine the intensity of precipitation. d. Equipment for Sky Condition. There is no equipment required for automated

5/11/01 7900.5B

sky condition sensor backup. If independent cloud height equipment is available, it should be used to obtain cloud height information. If such equipment is not available, visual estimates shall be made. Pilot reports of cloud heights may be used if available. e. Equipment for Temperature and Dew Point. A remote readout hygrothermometer is an acceptable backup for temperature and dew point. Other acceptable backups are a sling psychrometer, a battery-operated self-contained psychrometer, or a stand-alone temperature measuring device, as approved by FAA. f. Equipment for Altimeter Setting. Equipment to back up altimeter setting may be any FAA installed and maintained altimeter setting indicator (ASI) or digital altimeter setting indicator (DASI), or any other facility station pressure instrument, with certification and calibration traceable to the National Institute of Standards and Technology as defined in FAA Order 7210.3, Facility Operation and Administration. g. Equipment for OID/OT. If the ASOS OID fails, and the ASOS observation is currently representative, the observer shall continue to maintain oversight of the ASOS through the use of other ASOS displays (e.g., Video Display Unit (VDU)) and shall make appropriate maintenance notifications. If significant weather is occurring or expected to occur, after coordinating with ATCT, arrange, through appropriate maintenance channels, for local and long-line communications to be disabled. Notify on-site users that have ASOS displays to turn off power to their display. Provide backup observations. h. Equipment for Communications. No additional equipment is required for the

communication of backup weather information. If the primary communications equipment is unavailable, any appropriate communications media may be used. When long-line communications are unavailable, request that weather information be disseminated by the FSS/AFSS. i. Equipment Requirements for NF-OBS Providers. The NF-OBS provider shall provide and maintain all backup equipment. The cost of procuring, installing, operating, moving (if required), protecting and maintaining all instruments and equipment in accordance with FAA and NWS specifications is to be borne by the provider. The OID, which is part of the ASOS, will be maintained and serviced by the Government. 6-5. PROCEDURES FOR PROVIDING BACKUP INFORMATION General observer procedures for providing required backup information are summarized in Figure 4-1, Operator Procedures for Providing Augmentation and Backup Information. At ASOS sites, required weather data elements shall be entered into the automated weather observing system using the editing procedures for the automated weather observing system operator interface device.

At AWOS sites, entry of data shall be as specified in the AWOS Operators Instructions or the appropriate FAA approved AWOS manufacturer's equipment manual. For non-representative data, the observer may turn report processing off (ASOS) or set the channel out of service (AWOS). The turning off of report processing will lead to a “$” sign, and the generation of a trouble ticket for the NWS ASOS Operations and Monitoring Center (AOMC). Observers shall not turn off report processing for altimeter setting without appropriate maintenance notification. Once the report processing for the altimeter setting is turned off, only an

7900.5B 5/11/01

NWS technician can turn the report processing back on. 6-6. CODING OF MISSING DATA If any element, normally included in the body of the observation, except present weather and obscurations, is missing because of sensor failure, and that element is not required for backup, that element may be omitted. If the automated weather observing system's processor is operative, the system will do this automatically. If not operative, these missing elements shall be omitted and skipped over. When an element or phenomena does not occur, or cannot be observed, the corresponding group and preceding space are omitted from that particular report.

6-7. PROCEDURES FOR WIND SPEED AND WIND DIRECTION General procedures for the reporting of backup weather information for wind are given in Figure 6-2, Backup Reporting of Wind or Altimeter Setting. Alternate equipment, as specified in paragraph 6-4a, Equipment for Wind Direction and Speed, shall be used to determine wind direction and speed as appropriate. If no backup sensor is available, wind speed and direction shall be estimated. The character (gusts) of wind shall be reported from a wind speed recorder if available. Other sensors, or an estimate, shall be used if a wind recorder is not available. a. Estimating Wind Direction. Wind direction shall be estimated by observing the wind cone or tee, movement of twigs, leaves,

BACKUP REPORTING OF WIND OR ALTIMETER SETTING

LOCATION/CONDITION REPORTING PROCEDURES

ALL LOCATIONS WITH SURFACE-BASED OBSERVER PRESENT

Sensor Failure 1. Observer reports manually observed wind1 or altimeter setting2 in body of observation via designated procedures3 and makes appropriate maintenance notification. Non-representative Data 1. Observer may turn report processing off (ASOS) or set channel out of service (AWOS). 2. Observer reports manually observed wind or altimeter setting as above. For sensor failure only make appropriate maintenance notification. OID/OT/communications failure 1. Observer reports system wind or altimeter setting in body of report via designated procedures and makes appropriate maintenance notification.

LAWRS TOWERS All Conditions 1. Tower follows same procedures as above for observers.

NON-LAWRS TOWERS (WITHOUT A SURFACE-BASED OBSERVER) All Conditions 1. No backup information provided. FOOTNOTES: 1. Manual wind observations shall be obtained from the best available approved wind sensor. The LLWAS centerfield wind sensor may be used as an approved wind sensor. If all approved wind sensors are inoperative, the wind shall be estimated. 2. Manual altimeter settings may be obtained from any approved altimeter setting instruments including DASIs. 3. Designated procedures are specified in Figure 4-1.

Figure 6-2. Backup Reporting of Wind or Altimeter Setting

5/11/01 7900.5B

smoke, etc., or by facing into the wind in an unsheltered area. When estimating wind direction, note that even small obstacles may cause variations. The movement of clouds, regardless of how low they are, shall not be used for estimating the surface wind direction.

b. Estimating Wind Speed. The Beaufort Scale (see Figure 6-3, Estimating Wind Speed) shall be used to estimate wind speed if all other wind speed measuring instruments are out of service.

WIND EQUIVALENT -- BEAUFORT SCALE

KTS Specifications

<1 Calm; smoke rises vertically

1-3 Direction of wind shown by smoke drift not by wind vanes

4-6 Wind felt on face; leaves rustle; vanes moved by wind

7-10 Leaves and small twigs in constant motion; wind extends light flag

11-16 Raises dust, loose paper; small branches moved

17-21 Small trees in leaf begin to sway; crested wavelets form on inland waters

22-27 Large branches in motion; whistling heard in telegraph wires; umbrellas used with difficulty

28-33 Whole trees in motion; inconvenience felt walking against the wind

34-40 Breaks twigs off trees; impedes progress

41-47 Slight structural damage occurs

48-55 Trees uprooted; considerable damage occurs

56-71 Widespread damage

Figure 6-3. Estimating Wind Speed

7900.5B 5/11/01

BACKUP REPORTING OF SURFACE/TOWER VISIBILITY

LOCATION/CONDITION REPORTING PROCEDURES

ALL LOCATIONS WITH SURFACE-BASED OBSERVER PRESENT Sensor Failure 1. Observer reports prevailing surface visibility via designated procedures1, 2. 2. At towers, observer reports tower visibility, as required, via augmentation.2 Non-representative Data 1. Observer may turn report processing off (ASOS) or set channel out of service (AWOS). 2. Observer reports surface/tower visibility as above under sensor failure. OID/OT/communications failure 1. Observer reports system visibility via designated procedures.2 2. At towers, observer reports tower visibility, as required, via augmentation.2

LAWRS TOWERS Sensor Failure 1. Tower reports visibility.2 Non-representative Data 1. Tower reports visibility. 2. Tower may turn report processing off (ASOS) or set channel out of service (AWOS). 3. Observers shall not turn off report processing for altimeter setting without appropriate maintenance notification. OID/OT/communications failure 1. Tower reports visibility.2

Footnote: 1. Designated procedures are specified in Figure 4-1. Footnote: 2. Observer or tower shall make appropriate maintenance notification.

Figure 6-4. Backup Reporting of Tower/Surface Visibility

6-8. PROCEDURES FOR VISIBILITY General procedures for the reporting of backup information for visibility are given in Figure 6-4, Backup Reporting of Tower/Surface Visibility. The visibility shall be a prevailing visibility. (Note: RVR is not addressed here because it will not be backed up by FAA controllers (including LAWRS).) a. Reporting Visibility Values. In backing up visibility, the reportable values for visibility shall be the manual visibility values as permitted by the current system software installed; see Figure 9-1, Reportable Visibility Values. If the actual visibility falls between two reportable values, the lower value shall be reported. b. Tower Visibility During Backup (with Surface Observer). During backup

periods at towered facilities with a surface-based observer, the responsible tower controller shall: (1) Notify the surface-based observer when the tower prevailing visibility is observed to decrease to less than, or if below, increases to equal or exceed, 4 miles. (2) Report all changes of one or more reportable values to the surface-based observer when the prevailing visibility at the tower or the surface is less than 4 miles. (3) As required by FAA directives, use the lower of either the tower or weather station visibility as controlling visibility for aircraft operations.

5/11/01 7900.5B

REPORTING OF WEATHER PHENOMENA

LOCATION/CONDITION REPORTING PROCEDURES

ALL LOCATIONS WITH SURFACE-BASED OBSERVER PRESENT Sensor Failure 1. Observer reports manually observed present weather1 in body of observation via designated procedures.2, 3 Non-representative Data 1. Observer may turn report processing off (ASOS) or set channel out of service (AWOS). 2. Observer reports manually observed present weather as above for sensor failure. OID/OT/communications failure 1. Observer reports system weather in body of report via designated procedures.3

LAWRS TOWERS All Conditions 1. Tower follows same procedures as above for observers.

FOOTNOTES: 1. Weather and obscuration requirements are outlined in Figure 6-6. 2. Designated procedures are specified in Figure 4-1. 3. Observer shall make appropriate maintenance notifications.

Figure 6-5. Backup Reporting of Weather Phenomena

6-9. PROCEDURES FOR PRESENT WEATHER AND OBSCURATIONS General procedures for the reporting of backup information for present weather and obscurations are given in Figure 6-5, Backup Reporting of Weather Phenomena. Present weather and obscurations to vision shall be observed and reported in accordance with the manual procedures prescribed in Chapter 11, Weather Phenomena. Reports shall include as a minimum those weather phenomena in Figure 6-6, Backup and Augmentation Weather and Obscurations, when backing up ASOS. (If the observer is

backing up ASOS at the close of augmentation/ backup coverage, it will be necessary to end the event or it will continue to be reported during the hours when there is no augmentation/backup coverage.) Precipitation of unknown form is generally only reported when the automated weather observing system present weather indicator sensor is operational and is reporting precipitation of unknown form. However, if the observer can determine the type of precipitation, it should be reported according to the guidelines in Figure 6-6, via the non-representative data procedures.

7900.5B 5/11/01

Phenomenon

Observed

Report (Notation)

Phenomenon

Observed

Report (Notation)

Tornado +FC (in body); TORNADO (in remarks)

Snow Pellets or Small Hail

GS

Funnel Cloud FC (in body); FUNNEL CLOUD (in remarks)

Volcanic Ash VA

Waterspout +FC (in body); WATER- SPOUT (in remarks)

Fog (Vsby <5/8) FG

Thunderstorm TS Mist (Vsby > 5/8) BR

Rain RA Shallow (ground) Fog

MIFG

Rain Shower Report RA for ASOS * Patchy Fog BCFG

Drizzle DZ Freezing Fog FZFG

Freezing Rain FZRA Blowing Snow BLSN

Freezing Drizzle FZDZ Haze HZ

Ice Crystals Report SN for ASOS * Smoke FU

Ice Pellets PL Squalls SQ

Ice Pellet Showers Report PL for ASOS *

Hail GR

Snow SN

Snow Showers Report SN for ASOS *

Snow Grains Report SN for ASOS *

Explanatory Notes:

1. * Due to limitation on what phenomena ASOS software will accept.

2. A complete list of weather and obscuration elements is provided in Appendix E, METAR User Aids.

3. Augmented ASOS sites without ALDARS: Tornadic activity, thunderstorms, hail, volcanic ash, and virga elements are produced via augmentation, with all other elements above produced via backup.

4. Augmented AWOS sites without ALDARS: All the elements reported above are produced via augmentation.

5. Augmented ASOS or AWOS sites with ALDARS: Thunderstorm reporting is produced via backup if ALDARS should become inoperative, or is unrepresentative.

6. Present weather elements shall be reported in the body of the observation unless software precludes them from being reported in the body, then these elements shall be reported in the remarks portion of the METAR or SPECI.

Figure 6-6. Backup and Augmentation Weather and Obscurations

5/11/01 7900.5B

BACKUP REPORTING OF SKY CONDITION LOCATION/CONDITION REPORTING PROCEDURES ALL LOCATIONS WITH SURFACE-BASED OBSERVER PRESENT Sensor Failure 1. Observer reports manually observed sky condition to 12K feet, or as specified in the designated service level standard, whichever is greater; in body of report via designated procedures1. Non-representative Data 1. Observer may turn report processing off (ASOS) or set channel out of service (AWOS). 2. Observer reports sky condition as above for sensor failure. OID/OT/communications failure 1. Observer reports system sky condition data in body of report via designated procedures.1

LAWRS TOWERS All conditions 1. Tower follows same procedures as above for observers. NON-LAWRS TOWERS (WITHOUT A SURFACE-BASED OBSERVER) All conditions 1. No backup information provided

Footnote: 1. Designated procedures are specified in Figure 4-1. Make appropriate maintenance notification.

Figure 6-7. Backup Reporting of Sky Condition

6-10. PROCEDURES FOR SKY CONDITION General procedures for the reporting of backup weather information for sky condition are given in Figure 6-7, Backup Reporting of Sky Condition. More details on procedures for observing sky condition are included in Chapter 12, Sky Condition. If required, the following procedures for reporting sky condition shall apply: a. Reporting Procedures. (1) Report sky cover up to 12,000 feet, or as specified in the designated service level standard, whichever is greater. (See Appendix D, Service Standards.) (2) Non-opaque cloud layers shall be treated as opaque and reported. (3) No more than three layers shall be reported, and (4) "CLR" (clear) shall be reported at an automated site when no clouds are visible

up to 12,000 feet, or as specified in the designated service level standard, whichever is greater. b. Sky Cover. Sky cover is any clouds or obscuring phenomena aloft detected from the observing location. It shall be evaluated with reference to the surface. All clouds or obscuring phenomena aloft shall be considered opaque sky cover. c. Sky Condition Evaluation. Evaluation of sky condition shall include the amount and height of cloud bases up to 12,000 feet, or as specified in the designated service level standard, whichever is greater. d. Reporting Ceiling. The lowest layer that is reported as broken or overcast shall be the ceiling. If the sky is totally obscured, the height of the vertical visibility shall be the ceiling. e. Vertical Visibility. Vertical visibility shall be either:

7900.5B 5/11/01

(1) The distance that an observer can see vertically into a surface-based obscuring phenomenon. (2) The height corresponding to the top of a ceiling light projector beam. (3) The height at which a balloon completely disappears during the presence of a surface-based obscuring phenomenon. (4) The height determined by the sensor algorithm at an automated station. f. Obscuration. The portion of sky (including higher clouds, the moon, or stars) hidden by weather phenomena either surfacebased or aloft. At designated stations, obscurations are indicated in the remarks of the report. g. Number of Layers Reported. Automated weather observing stations shall report no more than three layers of clouds or one layer for an obscuring phenomena. Manual weather observing stations shall report no more than six layers. If multiple cloud layers are observed below 12,000 feet, up to three layers shall be reported in accordance with the priorities in Figure 6-8, Priority for Reporting Cloud Layers.

Continue reading ↓ 120 of 525 passages shown