Radar Vectors
Advisory Circular Current Issued Jan 30, 1987 AFS-300 65 pages Copy saved Nov 17, 2026

AC 65-2D Airframe and Powerplant Mechanics Certification Guide

Official source ↗ Open PDF

AC 65-20

Airframe &Powerplant

MECHANICS Certification Guide

U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

AIRFRAME AND POWERPLANT MECHANICS

CERTIFICATION GUIDE

Revised

1976

- U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

PREFACE

This guide was prepared by Flight St.andards Service, Federal Aviation Administration, to provide information to prospective airframe and powerplant mechanics and other persons interested in the certification of mechanics. It contains information about the certificate requirements, application procedures, and the mechanic written, orat and practical tests.

This guide supersedes AC 65-2C, Airframe and Powerplant Mechanics Certification Guide, dated 1973.

iii

CONTENTS

Page

PREFACE ----------------------------------------------------------- 111

CoNTE~ ------------------------------ --------------------------- V

INTRODUCTION ---------------- ---- ---------------------------------- V11

ELIGIBILITY REQUIREl\!ENTS FoR CERTIFICATION ----------------------- 1 Eligibility requirements: general ---------------------------------- 1 Knowledge requirements - -- -------------------------------------- 1 Experience requirements ------------------------------------------ 1 Skill requirements ----------------------------------------------- 1 Certificated aviation maintenance technician school students --------- 1

TIIE VVRITTEN 1rESTS --- ----- -------------------------- ----------- - - 3 Written Test Report --------------------------------------------- 4 Retesting after failure ------------------------------------------- 4

AVIATION MECHANIC TEsT CoNTENTS -------------------------------- 5 Aviation :Mechanic General Test ------------------------ - --------- 7 Basic electricty -------------------------------------------------- 7 Aircraft drawings ------------------ --------------------------- 8 Weight and balance -------------------------------------------- 8 Fluid lines and fittings -----------------------------.:.----------- 9 Materials and processes -- --------------------------------------- .9 Ground operation and servicing ------------------------------ --- 10 Cleaning and corrosion control ---------------------------------- 11 Mathematics --------------------------------------------------- 11 Maintenance forms and records ---------------------------------- 12 Basic physics ------------- ------------------------------------- 12 Maintenance publications --------------------------------------- 13 Mechanic privileges and limitations ------------------------------ 13

AnATION MECHANIC AIRFRAME TEsT -------------------- --------- - - - 15 Section 1. Airframe structures -------- --------------------------- 15 Wood Structures - -- ---- ------------ ~--- - ----------------------- 15 Aircraft covering ---------------------------------------------- 15 Aircraft finishes ------- ---------------------------------------- 15 Sheet metal structures --------------------------------------- --- 16 Welding ------------------------------------------------------- 17 Assembly and rigging --------------------------------- --------- 18 Airframe inspection ---- --- ---------- ---------- ----------------- 20 Section 2. Airframe systems and components - ---------- ---------- 21 Aircraft landing gear systems --------------- ---------------- --- 21 Hydraulic and pneumatic power systems ---------------------- --- 21 Cabin atmosphere control systems ------------------------------- 23

v

CONTENTS-Continued

Page Aircraft instrument systems ------------------------------------ 24 Communication and navigation systems -------------------------- 24 Aircraft fuel systems ------------------------------------------- 24 Aircraft electrical systems -------------------------------------- 25 Position and warning systems ----------------------------------- 27 Ice and rain control systems ------------------------------------ 27 Fire protection systems ----------------------------------------- 27

AVIATION MEcHANIC PoWERPLANT TEsT ------------------------------ 29 Section 1. Powerplant theory and maintenance … 29

]Reciprocating engines ------------------------------------------ 29 Turbine e~es ----------------------------------------------- 31 ~~ne inspection ---------------------------------------------- 31 Section 2. Powerplant systems and components -------------------- 33

~ngine instrument systems -------------------------------------- 33 ~~e fire protection systems ----------------------------------- 33

~ngine electrical systems --------------------------------------- 33 Lubrication systems -------------------------------------------- 35 Ignation systenns ----------------------------------------------- 36 Fuel metering systems ------------------------------------------ 37

~ngine fuel systems -------------------------------------------- 39 Induction systems ---------------------------------------------- 39

~ngine cooling systems ----------------------------------------- 40 ~~e exhaust systems ---------------------------------------- 40 Propellers ----------------------------------------------------- 40 ~ AND ~~CAL 1r.EsTS ----------------------------------------- 43 1rhe oral test ---------------------------------------------------- 43 Sample oral test questions -------------------------------------- 43 1rhe practical test ------------------------------------------------ 44 Sample practical test projects ----------------------------------- 44

SA~LE VVRrrTEN 1rEBT ~~TIONS ----------------------------------- 47

RECOMMENDED STUDY MATERIALs

Federal Aviation Regulations (FAR) ----------------------------- 55 FAA Advisory Circulars ----------------------------------------- 55 Miscellaneous FAA publications ---------------------------------- 57

APPENDIX

FEDERAL AVIATION REGULATIONS ------------------------------------- 59 MAP SHOWING FAA REGIONS --------------------------------------- 61 FAA REGIONAL 0F:FrCEs AND FLIGHT STANDARDS DisTRicT. OFFICES ------ 62

Vl

INrRODUCTION

The requirements for a mechanic certificate and ratings, and the privileges, limitations, and general operating rules for certificated mechanics are prescribed in Federal A vi ation Regulations Part 65-Certification: Airmen Other Than Flight Crewmembers. Any person who applies and meets the requirements is entitled to a mechanic certificate.

Briefly, the requirements for a mechanic certificate are concerned with age, language ability, experience, knowledge, and skill. The sections of this guide explain the procedure for either substantiating or demonstrating that each requirement has been met.

The sections that deal with the written test (to demonstrate knowledge) and the oral and praotical tests (to demonstrate skill) describe the types of tests used and what they contain. The subject listings and the sample questions and projects should be helpful during preparation for the tests.

Portions of the Federal Aviation Regulations (FAR) conoerning general eligibility and experience requirements for a mechanic certificate and

ratings have been included~ Since regulations are subject to amenflment,

applicants should be alert for changes that may have occurred since publication of this guide. Change information may be determined by referring to the most recent FAR Status Sheet mentioned in the Appendix, or by checking -with an FAA Flight Standards district office. The F .ARs hav~ been organized and printed in eleven volumes of interrelated Parts. Refer to the

.Appendix, FAR Status Sheet, for information about the FAR rearrangement.

FAA Flight Standards district offices are listed in the appendix and each office serves the geographical area in which it is located. .Applicants should contact the most convenient office.

vii

ELIGffiiLITY REQUIREMENTS FOR CERTIFICATION

Mechanic certificate requirements can be classified as general eligibility requirements, knowledge requirements, experience requirements, and skill requirements. The following excerpts from FAR Part 65 pertain to eligibility for a mechanic certificate and rating(s).

"§ 65.71 Eligibility requirements: general.

(a) To be eligible for a mechanic certificate and associated ratings, a person must­

(1) Be at least 18 years of age; (2) Be able to read, write, speak, and un:derstand the English language, or in the case of an applicant who does not meet this requirement and who is employed outside of the United States by a U.S. air carrier, have his certificate endorsed 'Valid only outside the Unit.ed States';

(3) Have passed all of the prescribed tests within a period of 24 months; and

(4) Comply with the sections of this subpart. that apply to the rating he seeks.

(b) A certificat-ed mechanic who applies for

lUI. a·dditional rating must meet the requirements of § 65.77 and, within a period of 24 months, pass the tests prescribed by § § 65.75 and 65.79 for the additional rating sought.

"§ 65.75 Knowledge requirements.

(a) Each app1i"Cant for a mechanic certificate or rating must, after meeting the applicable experience requirements of § 65.77, pass a wrillten test covering the construction and maintenance of aircraft appropriate to the rating he seeks, the regulations in this subpart, and the applicable provisions of Parts 43 and 91 of this chapter. The basic principles covering the installation and ma.intenan'Ce of propellers are included in the powerplant test.

(b) The applieant must pass each section of the test before applying for the oral and

practical tests prescribed by § 65.79. A report of the written test is sent to the applicant.

"§ 65.77 Experience requirements.

Each applicant for a mechanic certificate or rating must present either an appropriate graduation certificate or certificate of completion from a certificated aviation maintenance technician school or documentary evidence, satisfactory to the Administrator, of­

(a) At least 18 months of practical experience with the procedures, practices, materials,

t~ls, machine t~ls, and equipment generally used in constructing, maintaining, or altering airframes, or powerplants appropriate to the rating sought; or

(b) At least 30 months of practical experience concurrently performing the duties appropriate to both the airframe ami powerplant ratings.''

The documentary evidence specified in § 65.77 may take any of various forms, such

<\S letters from present and former employers, miJita.ry service records, business record·s, etc., as Jong as the F A.A. inspector or advisor who reviews it is able t:o determine that the type and amount of experience meets the requirements.

"§ 65.79 Skill requirements.

Ea·ch applicant for a mechanic certificate or rating must pass an oral and a practical test on the rating he seeks. The tests cover the applicant's basic skill in performing practical projects on the subjects covered by the written test for that rating. An applicant for a powerplant rating must show his ability to make satisfactory minor repairs to, and mirror alterations of, propellers.

"§ 65.80 Certificated aviation maintenance

technician school students. Whenever an aviation maintenance technician school certificated under Part 147 of this

1

chapter shows to an FAA inspector that any of its students has made satisfactory progress at the school and is prepared to take the oral and practical tests prescribed by § 65.79, that student may take those tests during the final

subjects of his training in the approved curriculum, before he meets the applicable experience requirements of§ 65.77 and before he passes each section o£ the written test prescribed by § 65.75."

2

THE ~TTEN TESTS

The written tests required for a mechanic certificate or rating can be taken at FAA Flight Standards district offices and at some selected Flight Service Stations. Some Flight Standards district offices administer mechanic written tests at special locations by prior arrangement, and some Flight Service Stations often administer written tests after the normal workday and on weekends. Contact the local FAA district office for information about time and place where tests are administered.

Most FAA offices that administer written tests recommend that an appointment be made before the intended date of examination so that the appropriate personnel will be on hand to give the tests and to assure that adequate

space is available.

An applicant must have the documentary evidence required by FAR 65.77 reviewed by an FAA inspector to confirm eligibility to take a written Airframe or Powerplant test. Those applicants found to be eligible for testing who are unable to take the test at that time may request the FAA inspector to issue

an Airman Authorization for Written Test, FAA Form 8060-7.

When eligibility has been confirmed or the completed 8060-'7 is presented and sufficient time exists ( 5 hours) to complete the test, the

FAA office test monitor will issue a test booklet, a blank answer sheet, and all materials necessary to take the test. The applicant is not required to furnish any test or reference

materials, nor permitted to use notes or take notes during the test.

Written tests ·for airframe and powerplant mechanic certification consist of three separate tests: (1) Aviation Mechanic General Test;

(2) Aviation Mechanic Airframe, Section 1­

Airframe Structures, and Section 2---Airframe

Systems & Components; and (3) Aviation Mechanic Powerplant, Section 1-Powerplant Theory & Maintenance, and Section 2--­ Powerplant Systems & Components.

Applicants will not be required to take the Aviation Mechanic General Test required for Airframe and/ or Powerplant certification if they can show that they have previously passed it. Proof of passing may be in the form of a mechanic certificate with an alternate rating or an Airman Written Test Report that shows a passing grade on the Aviation Mechanic General Test. I£ an Airman Written Test Report is used, the passing credit must have been earned within the preceding

24 months.

FAA mechanic written tests are made up of objective-type questions of the multiplechoice form. In this type of test, the applicant chooses the best of a number of possible

answers to a question. Each of the FAA mechanic written test questions has one best answer and three wrong or unacceptable alternative answers. The tests do not contain questions designed to trick or mislead the applicant.

· After completion of the test, the applicant's answer sheet is forwarded by the local FAA office to a central location for grading. The minimum passing grade for FAA tests is 70

percent. Written test grades are mailed directly to the applicant using the address entered by the applicant on the answer sheet at the time the test is taken. Five working

days (exclusive of time en route in the mail) are normally required for answer sheets to be processed and grades reported.

3

Written Test Report

Written test grades are reported to applicants on AC Form 8080-2, Airman ·written Test Report. The report indicates the numerical grade for each test section and an expiration date of each test section pa~sed. AC

Form 8080-2 is the only acceptable evidence of having passed any part of the written test

or the entire test.

In addition to grade information, the com~ puter-rendered AC Form 8080-2 provides a coded print~out of the subject areas for which questions were answered wrong. The subject area codes indicated on AC Form 8080-2 correspond to the ·subject headings indicated on pages 7 through 42 of this advisory

circular; however, the number of questions missed cannot be determined by the number of codes listed on AC Form 8080-2.

When an applicant applies for the oral and practical test, the Airman Written Test Re~

port must be surrendered.

If the Airman Written Test Report is lost or destroyed, a duplicate copy may be obtained by sending $2.00 (money order or check pay­

able to FAA) to the Federal Aviation Administration, Airman Certification Branch, P.O. Box 25082, Oklahoma City, Oklahoma

73125. Give the title of the test, the place where it was administered, and the approxi­

mate date that the test was taken.

An applicant who fails a test, or any section

there9f~ may apply for a retest of the test

secyiqn._~s) failed as prescribed in FAR Part 65. The following excerpts from § 65.19 pertain to retesting after failure.

"§ 65.19 Retesting after failure.

An applicant who fails a written, oral, or practical test for a certificate and rating, or

for an additional rating, under this Part may apply for retesting­

(a) After 30 days after the date he failed the test; or

(b) Upon presenting a statement frorh whichever of the following persons is applicable, certifying that he has given the applicant at least 5 hours of additional in~ struction in each of the subjects failed and now considers that the applicant is ready

for retesting …

(3) For the mechanic certificate-a certificated and appropriately rated me~ chanic or ground instructor, or a certifi~ cated repairman who is experienced in

the subject failed."

4

AVIATION MECHANIC TEST CONTENTS

This listing of the subject material covered by the questions in the mechanic tests shows w ha't the applicant should know and be able to do. Each listing contains major headings

(identified by letters A, B, C, etc.) under which are listed one or more action lines. Each action line is ma-de up of 3 elements:

(1) the action, (2) the subject, and (3) the level. For instance, the major heading "C. Weight and Balance" in the General Test has two action lines :

(a) Weigh aircraft-Level 2. ('b) Perform complete weight and balance

check and record data-Level 3. The action lines tell what the end result or objective of the applioant's study and experience should be. Many action lines show more than one action and more than one subject.

The purpt.JSe of the level indicated for each action line is to help limit the amount of study that must be done or the· skill that must be developed to pass the mechanic tests. Three levels have been identified. The higher the level, the more comprehensive the knowledge

and skill required in that subjectarea. A Level 1 action line requires a less extensive knowledge of the subject and no skill demonstration to pass the mechanic tests. A Level 2 action line requires a fairly good understanding of the subject indicated, the theories an<~ principles associ·ated with it, and the ability to perform basic operations. Level 3, the highest level, requires a thorough knowledge of the subject and an understanding of how it relates to the total operation and maintenance

of aircraft. The operations necessary to complete Level 3 items mugt be performed skillfully enough so that, if performed on an aircraft, the aircraft could be returned to service.

A detailed description of the meaning of each level is :

Level 1:

Know-basic facts and principles. Be able to-find information and follow directions and written instructions. No skill demonstration is required. Level 2:

Know and understand-principles, theo­

ries and concepts. Be able to-find and interpret information and perform basic operations. A high level of skiH is not required.

Level 3:

Know, understand, and apply~facts, principles, theories, and concepts. Understand how they rela:te to the total operation and maintenance of aircraft. Be able to-make independent and accurate airworthiness judgments. Perform all operations to a. return-to-service standard. A fairly high skil'l level is required.

Following each action line is a list of statements that describe the specific subjects of mechanic test questions. They are intended to be used during study and while experience is being gained, to helip direct the applicant's attention toward areas covered by the tests.

5

AVIATION MECHANIC

General Test

A. BASIC ELECTRICITY.

Measure capacitance and inductance.- Levell:

The effect of inductive reactance in an electrical circuit.

The interrelationship of capacitive and inductive reactance.

The term that describes the combined resistive forces in an a.c. electrica;l cireuit.

The unit of measurement for capacitance •and inductance.

Calculate and measure electrical power.­ Level 2:

Determine the power furnished by a generator to an electrical system consisting of various electrical units having specific load ratings.

Determine the power required by an electric motor that is operating at a specified

efficiency and load.

Measure voltage, current, resistance, continuity, and leakage.-Level 3:

Use an ohmmeter to check for open or short circuits.

The test instruments used to check continuity.

The basic operating principle o£ d.c. electrica;l instruments.

The baSic operating principles of a galvanometer.

Connect voltmeters and ammeters into an electrical circuit.

The purpose of a shunt resistor when used with an ammeter.

The meaning of prefixes such as micro, mega, kilo, and milli as used in express­

ing electrical quantities.

Determine the relationship of voltage, current, and resistance in electrical circuits. -Level 3:

Determine the current flow in an electrical circuit using variable resistance and volt­

age values. Determine the power requirements of an electrical circuit when ~he voltage and

resistance values are specified. The current relationship in a parallel electrical circuit.

The unit of measurement used to express electrical power.

The principles of electromagnetic induction.

The characteristics of magnets and mag­ netic lines of force.

The factors that affect the voltage drop in an electrical conductor.

Determine the resistance of an electrical device from the wattage and voltage values specified.

Calculate the voltage drop across a re­ sistor.

Read and interpret electrical circuit diagrams.-Level 3:

Trace electrical circuits using aircraft

wiring diagrams.

Identify electrical system malfunctions by reference to circuit diagrams.

Identify the commonly used aircraft elec­ trical sy~bols.

Inspect and service batteries.-Level 3:

Remove spilled el~rolyte and treat all

adjacent surfaoos. Remove and install a battery in an aircraft with a single-wire electrical system.

7

Connect batteries to a constant-current battery charger.

Determine the specific gravity of the bat­ tery electrolyte.

Perform a high-rate-discharge condition test of batteries. The design factors that affect battery voltage and capacity. The factors that determine battery charg­ ing rate on a constant voltage source.

The indications of a shorted battery cell.

The significance of battery capacity

ratings. The effects of increased internal resistance on battery operation. The effects of connecting battery cells in series or parallel. The relative advantages of lead-acid and nickel-cadmium batteries for use in air­

craft. The principles of battery construction. Check battery electrolyte levels. The r~elationship between battery state of charge and the temperature at which the electrolyte will freeze. The purpose of and requirements for ventilating batteries and battery compart­

ments in civil aircraft.

The effect of excessive charging rates on batteries.

B. AIRCRAFT DRAWINGS.

Use drawings, symbols, and schematic diagrams.-Level 2 :

Interpret the various types of lines employed in blueprints and schematics.

Use schematic diagrams to analyze system malfunctions. Extract a specific electrical circuit from a system drawing.

Know why dimensions are used and how they are shown on aircraft drawings.

Use installation diagrams to locate and

identify components.

Draw sketches of repairs and alterations. -Level 3:

Illustrate a major repair or alteration. Use dividers, compass, ruler, T-square, etc., in the development of sketches of repairs and alterations. Use standard drafting procedures.

Use blueprint information.-Level 3:

The information presented in blueprint title blocks. The common symbols used on aircraft blueprints.

Install and modify component parts by reference to blueprints.

Identify the changes made to a blueprint.

Use graphs and charts.-Level 3:

Determine electric cable size and currentcarrying capacity.

Determine engine power requirements.

C. WEIGHT AND BALANCE.

Weigh aircraft.-Level 2:

Use aircraft specifications for weighing purposes. Locate jacks and scales in the correct position.

Prepare aircraft for weighing.

Perform complete weight-and-balance check and record data.-Level 3:

Determine that the forward or rearward center-of-gravity (e.g.) limit is not ex­

ceeded on a specified aircraft. The point of reference for all weight­

and-balance measurements.

~he procedure for computing "minimum fuel." Locate the information that should be krrown to compute weight and balance.

The method of expressing additions or

rem~vals of equipment for weight-andbalance purposes.

Determine the fully loaded center of gravity of an aircraft.

8

Determine the "maximum authorized weight" of an aircraft.

The method of determining aircraft empty weight, when engine oil and hydraulic fluid are contained in supply tanks.

The effect on weight and balance of re­ placing a component with another of different weight and location.

Calculate the maximum cargo or baggage weight that can be carried by an aircraft.

The record requirements for weight--and­ balance data.

The hazards of exceeding aircraft fore and aft center-of-gravity limits.

The critical conditions of helicopter load and balance.

Determine aircraft empty weight and empty weight center of gravity.

Define maximum gross weight.

Determine the moment of an item of equipment.

Account for tare weight When weighing an aircraft.

D. FLUID LINES AND FITI'INGS.

Fabricate and install rigid and flexible fluid lines and fittings.-Level 3:

Single- and double-flare tubing.

Install Military Standard (MS) flareless fittings.

The significance of the identification

stripes that appear on aircrdt hose.

Fabricate and install beaded tubing.

Use lubricants and sealants in the assem­ bly of lines and fittings.

Identify :flexible hydraulic lines.

Install hose clamps.

Determine the bend radii for rigid tubing.

Fa:bricate aluminum tubing using stand­ ard AN flared tube fittings.

Route fluid lines in entry-ways and passenger, crew, or baggage compartments. Repair metal tube lines.

Route fluid lines adja~nt to electrical power cables.

Install rigid tubing.

Select tube-flaring tools. Identify AN fitting materials from color designators.

The maximum reduction in original out­

side diameter allowed when bending a:lum­ inum alloy hydraulic lines. The procedure to follow if scratches are detected on an aluminum alloy tube. The storage requirements for hydraulic hose.

Insta'll flexible hydraulic hose. The lubricant used when assembling oxy­ gen fittings.

E. MATERIALS AND PROCESSES.

Identify and select appropriate nondestructive testing methods.-Level 1 :

The use of radiography in aircraft and component inspection.

The use of ultrasonic inspection methods for detecting cracks.

The applicability of magnetie particle inspection methods to engine crankshafts. The method for detecting surface cracks in aluminum castings and forgings. The teehnique for locating cracks in materials when only one side of the materi'8.1 is a.ccessib1e.

Perform penetrant, chemical etching, and magnetic particle inspections.-Level 2:

The general procedure for performing magnetic particle inspection.

Demagnetize steel parts after magnetic particle inspection.

Clean parts in preparation for penetrant inspection. ·

The visual indications of a subsurface flaw or fracture during magnetic particle inspection.

Locate cracks and blowholes in welded '8.5SeiD.blies.

9

The ptocedure for using dye penetrants.

Distinguish between heat-treated and nonheat-treated aluminum alloys when the

identification marks are not on the material.

Perform basic heat-treating processes.­ Level 2:

The types of aluminum alloys considered to be heat treatable. Anneal copper tubing. The steps in heat treatment of aluminum alloys. The effects of various forms of heat treat­ ment. The effect of incorrect heat treatment on the corrosion-resistant properties of alum­ inum al'loy. Identify the degree of temper for alumi­ num alloy products from code designators. The effect of heating a metal slightly

above its critical temperature, and then rapidly cooling it. The effect of strain hardening on the tensile strength of aluminum aHoy. The relationship between tensile strength and metal hardness.

.Anneal a welded steel part.

Identify and select aircraft hardware and materials.-Level 3:

Identify aluminum alloys from code designators. Identify steel from code designators. The identification markings of AN stand­ ard steel bolts. Identify aircraft ca:ble.

The characteristics of a material that affect its ability to be hammered, rolled, or pressed into various shapes. The SAE system of identifying steel. Determine wrought aluminum alloy com­ position and condition by referring to aluminum codes.

Ins6a'll self-locking nuts.

Detennine the correct length bolt to use.

Determine correct torque values for tightening aircraft nuts and bolts.

Determine rivet composition, condition, shape, and dimension by referring to rivet code.

Identify materials suitable for use for firewalls and exhaust shrouds. Install castle nuts. The strength characteristics of type "A" rivets.

The characteristic of aluminum a:lloy

rivet material that causes some rivets to require several days to reach their ultimate strength. Determine that materials used in aircraft maintenance and repair are of the proper type and confor-m to the appropriate standards.

.The characteristics of aluminum-clad

sheet aluminum alloy. Insped and check welds.-Level 3:

The characteristics of a good weld. The types of stress that w~lded joints can wilihstand. The effect of welding over a previously brazed or soldered joint . Perform precision measurements.-Level 3: Use a micrometer and a caliper to make ·precise measurements.

Measure a small hole using a micrometer and a hole gage. Read and interpret a vernier micrometer scale. Use a dial indicator, V -blocks, and a sur­ face p'late to check alignment of a sha.ft.

F. GROUND OPERATION AND SERV­

ICING. Start, ground operate, move, service, and secure aircraft.-Level 2:

The procedure for extinguishing fires in the engine induction system during starting.

10

Use hand signals to direct aircraft move~ ment. Select and use extei'l'l.al auxiliary power

units for engine starting.

Tie down and secure aircraft for outside storage.

Protect aircraft fuel system from con­ tamination during fueling operations.

Connect and operate ari external source of hydraulic power. Start and operate an engine equipped with a float-type carburetor.

Check a reciprocating engine for liquid lock. Operate hand and electrica:l priming sys­ tems during engine starting. Start and operate an engine equipped witJh a pressure injection carburetor.

Start and operate an engine equipped with an internal supercharger.

Identify and select fuels.-Level 2:

The effect of ethylene dibromide added to aviation gasoline.

The identifying color of various grades of aviation gasoline.

The characteristic of a fuel that affects

its tendency to "vapor lock."

The significance of the numbers used to designate various grades of aviation gasoline.

The relative advantages of gasoline and kerosene for use as fuel for turbine engines.

Determine the type o£ fuel to be used

with a specified aircraft.

The £actors affecting the antiknock dhar­

acteristics of fuel.

G. CLEANING AND CORROSION CON­

TROL. Identify and select cleaning materials.­ Level 3:

The effect of caustic cleaning products on aluminum structures.

The characteristics and use of chemical cleaners.

Clean aluminum and steel engine parts.

The type cleaner for use on high-strength metals.

The methods for cleaning turbine engine compressor blades.

Perform aircraft cleaning and corrosion control.-Level 3:

Protect tires and other ruhber products

from the deteriorating effects of cleaning materials.

The cause and corrective procedures for

fretting corrosion.

Identify and control intergranular cor­ rosion of heat-treated aluminum alloy.

Protect structure against dissimilar-metal corrosiOn.

Prevent and remove rust.

The effect of oi'ly, dirty surfaces on the operation o£ high-performance aircraft.

Protect interior surfaces of closed steel and alummum tubing against corrosion.

The methods of protecting aluminum

alloy parts against corrosion.

Clean and protect battery comp'artments and adjacent areas.

Remove corrosion products such as metal flakes, scale powder, and salt deposits from aluminum.

Clean corrosion-resistant parts by blast cleaning methods.

Use paints and similar organic coatings

for corrosion protection purposes.

H. MATHEMATICS.

Extract roots and raise numbers to a given power.-Level 1:

The method of determining the square or cube of a number.

The procedure for determining square

root

11

Determine areas and volumes of various geometrical shapes.-Level 2:

Calculate the area of rectangles, squares, triangles, circles and trapezoids.

Determine the volume of rectangles, cubes, and cylinders.

Compute the surface area of an airfoil.

Determine cylinder displacement of a reciprocating engine.

Solve ratio, proportion, and percentage problems.-Level 3:

Determine the ratio of two numbers.

Find what percent one number is of another.

Determine the rate percent of a given number.

Calculate the compression ratio of an engme.

Convert decimal numbers to their fraetional equivalent.

Perform algebraic operations involving addition, subtraction, multiplication, and division of positive and negative numbers. -Level3:

Locate the main-wheel weighing point

with reference to the datum.

Determine the distance between the tail or nose gear and the main-wheel weig'ht point.

Calculate the e.g. relative to the datum.

The effects of adding or removing equipment on the empty weight of the aircraft.

I. MAINTENANCE FORMS AND REC­

ORDS.

Write descriptions of aircraft condition and work performed.-Level 3:

Describe the repairs made to an aircraft structure.

State aircraft condition based upon inspection.

Complete required maintenance forms, records, and inspection reports.-Level 3:

Enter the required information in the permanent maintenance records when a minor reopair has been performed.

Prepare and properly dispose of FAA Form 3-37.

The minimum information required to be entered in the maintenance records after maintenance or alteration of aircraft.

Make record entries to indicate compliance with Airworthiness Directives.

The definition of "time in service" with respect .to maintenance records. The record requirements for returning

aircraft to service after·lOO-hour inspection.

The requirement for maintaining a permanent record of aircraft maintenance.

The definition of "r~air" as related to ·aircraft maintenance.

The requirements for a permanent maintenance record.

J. BASIC PHYSICS.

Use the principles of simple machines; sound, fluid, and heat dynamics.-Level 2:

The relationship between temperat~ and heat.

The methods of heat transfer. The forces acting upon a body in circular motion.

The relationship between the pressure and the rate-of-fi'Ow of a liquid through an orifice.

The relationship between the pressure, volume, and temperature of an air mass.

The relationship of work, force, and power.

The effect of air density on engine power output.

The relationship between air velocity and ·pressure on the upper surface of an air­ foil.

12

The effect of atmospheric temperature

and humidity on airfoil lift.

The principles of transmission of power in a hydraulic system.

The relationship of pressure, area, and force.

K. MAINTENANCE PUBLICATIONS.

Select and use FAA and manufacturer's aircraft maintenance specifications, data

~heets, manuals, and publications, and related Federal Aviation Regulations.­ Level 3:

Determine the suit~bility of a propeller for use with a particular engine-airplane combination.

Determine the minimum diameter of a.

propeller type and model when used with a. particular engine.

Locate aircra~t leveling and weighing in'furmation.

Determine engine/propel'ler speed ratios.

The instrument markings required on a

specified type and model aircraft.

The purpose and applica.Jbility of Technical Standard Orders. The purpose and applica.bility of Supplemental Type Certificates. Identify the useful load and empty weight e.g. of an aircraft ·by reference to data.

Use FAA Specifications and Type Certificate Data Sheets.

The applic·abi'lity and requirements for

aircraft airworthiness certificate."

Determine the control surface ffi'(}Vement

limits of a specified aircraft.

Determine seat locations of an aircraft,

using aircraft specifkations.

Use aircra-ft listing to find information about aircraft of limited production.

The purpose and applicability of FAA Airworthiness Directives.

Use "Table of Limits" to determine condition of parts.

Read technical data.-Level 3:

Find specified information in technical reports and manuals.

L. MECHANIC PRIVILEGES AND LIM­

ITATIONS. Exercise mechanic privileges within the limitations prescribed by FAR 65.-Level 3:

The criteria for determining the classification (major, minor, or preventive maintenance) of airframe repairs and alterations. The criteria for determining the classifi­ _cation (major, minor, or preventive maintenance) of powerplant repairs and alterations. The criteria for determining the classification (m'ajor, minor, or preventive maintenance) of propeller repairs and alterations.

Return an aircraft to service a-fter installation of an engine type other ~han that

for which t'he aircraft wa:s originally certificated.

The minimum age requirement for issuance of a mechanic certificate.

The privileges of a mechanic in relation to 100-hour and annual inspections.

The requirements for reporting change of address. The duration or effective period of a. mechanic certificate. The requirements an applicant must meet for issuance of a mechanic certificate.

Determine the maintenance classification

(major repair, minor r~pair, preventive maintenance) of landing gear tire removal, installation, and repair.

Determine the maintenance classification

(major repair, minor repair, preventive maintenance) of servicing landing gear shock struts.

Determine the repair classification (major repair, minor repair, preventive maintenance) of repairs to steel tubing structures by welding.

13

Determine the repair classification (major repair, minor repair, preventive maintenance) of repla:cing the fabric on fabriccovered parts such as wings, :fuselages, stabilizers, and control surfaces.

The recency-of-experience requirements

for certificated mechanics.

The privileges of a mechanic regarding return to service of aircraft after major

repairs.

Determine the maintenance classification

(major repair, mmor repair, preventive mairrtenance) of the replacement of aircraft components with new, rebuilt, or re­ ·paired components of similar design.

14

AVIATION MECHANIC AIRFRAME TEST

Section 1. Airframe Structures

A. WOOD STRUCTURES.

Service and repair wood structures.- Levell:

The general requirements of scarf splice joints. The repair procedure for elongated holes

in wood spars. The permissible wood substitutes for use

in making repairs to wood structures. The procedures for repairing wood rib

capstrips.

The characteristics of glue used in air­ craft construction and repair.

The procedure for sealing the inner sur­

faces of a wooden structure that is to be assembled by gluing.

The general c·haracteristics of the wood commonly used in aircraft construction.

Identify wood defects.-Lev~l2:

Recognize acceptable and nonaccepVa;ble wood defects.

Inspect wood structures.-Level 2:

The effect of moisture content on wood size and strength. The strength characteristics of wood structures. The characteristics of plywood and lami­ nated wood.

B. AIRCRAFT COVERING.

Select and apply fabric and fiberglass covering materials.-Level 1 :

The factors to consider in selecting aircraft fabric. The types of seams commonly used in ·aircraft fabric coverings.

The general requirements for making doped and lapped se~.

The meaning of the term "warp" as used in reference to aircraft textile products.

The precautions to observe when install­

ing surface tape on control surfaces.

Inspect, test, and repair fabrie and fiber· glass.-Level 3:

Determine the condition of aircraft fabric.

Apply a doped-on patch to aircraft fabric.

Make a sewed repair to a. fabric-rovered surface.

The areas on a fabric-covered aircraft most susceptible to corrosion.

C.. AIRCRAFT FINISHES.

Apply trim; Jette~ and touchup paint.- Levell:

The requirements for registration markings.

The relative proportions of identification markings.

The use of color and ornamentation when applying registration marks.

Identify and select aircraft finishing ma· terials.-Level 2:

The characteristics of butyrate and acetate dopes.

The types of thinners used with various types of paint and dope.

The characteristks of fabric rejuvenators.

The types of priming paints generally used on aircraft.

The type paint used to coat the insides of battery compartments.

15

Apply paint and dope.-Level 2: Insp-ect and repair plastics, honeycomb,

The purpose of fungicidal dope m aircraft finishing.

The application of rejuvenator to repair an aged dope finish.

The products and methods used to dope­ proof airframe structures.

The effect of atmospheric conditions on dope during its application.

Sand and rub aircraft finishes. Apply primer to aluminum alloy parts.

Use and maintain a paint spray gun. The purpose of brushing the first coat of dope instead of spraying.

Inspect finishes and identify defects.­ Level 2:

The type of painting defect caused by moving the spray gun in an arc instead of a straight line. The cause of runs and sags in aircraft finishes.

D. SHEET METAL STRUCTURES.

Install special rivets and fasteners.­ Level 2:

Determine correct riv~t length and diameter.

Install a hi-shear rivet.

The precautions concerning rivet fit.

Irrstall deicer boot fasteners.

Irrsta:ll blind-type rivets. The stresses that a rivet is designed to resist.

Inspect bonded structures.-Level 2:

The reason for using metal sandwich panels in high-speed aircraft construction. The use of the metanic "ring" test to inspect for delamination damage of bonded structures.

Evaluate the extent of damage to a bonded structure and determi.ne the type repair

needed.

and laminated structures.-Level 2:

Distinguish between transparent plastic and plate-glass enclosures.

Protect plastics during handling and repair operations.

Remove scratches and surface crazing

from plastic enclosures.

Drill shallow or medium depth holes in plastic materials. The effect of moisture entrapped in honey­ comb structures.

Use a router to remove damaged area

from honeycomb panels.

Cle'an honeycomb panels prior to patching.

Inspect, check, service, and repair windowSy doors, and interior furnishings.­ Level 2:

Clean transparent plastic window and

windshield materials.

Inspection procedures and airworthiness requirements for safety belts. The chanacteristics of acrylic plastic en­ closure materials. Maintain safety belts.

Secure transparent plastic endosures to the aircraft structure.

Protect transparent plastic enclosure ma­ terials during handling and storage.

The physica!l characteristics of transpar­ ent plastic enclosure materials. Form and shape acrylic plastic.

Repair shallow surface scratches in trans­ parent p1astic enclosures.

Inspect and repair sheet-metal structures. ---,Level 3 :

Select and use twist drills.

Select and use a hand file for soft metals.

Prepare dissimilar metals for assembly.

Determine the type, size, and number of rivets for use in structural repairs.

Repair sheet-metal flight control surfaces.

16

The loads acting upon a semimonocoque

fuselage.

The construction characteristics of mono­ coque and semimonocoque structures.

The construction characteristics of canti­

lever wing structures. The types of loads carried by wing spars.

Drill holes in stainless steel.

Define bearing failure as related to sheet­ metal structures.

Define shear failure.

Repair a hole in a stressed-skin metal wmg.

Repair a section of damaged skin using a single-lap sheet splice.

Construct a watertight joint.

Countersink a hole.

Perform the dimpling process.

Select the correct rivet oo accomplish a

repair using a specified material. Repair or splice stringers on the lower

surface of a stressed-skin metal wing. Determine the correct rivet layout and

spacing for a specified repair.

Use proper riveting techniques. Stop drill cracks in sheet metal.

Repair a slightly oversize hole. Repair structural units, such as spars, en­ gine supports, etc., that have been built from sheet me~al. Repair shallow scratches in sheet metal.

Determine the condition of a stressed­ skin metal structure that is known to have been critically loaded.

Use a reamer.

Install conventional rivets.-Level 3:

Prepare sheet metal for installa-tion of flush rivets. Identify and select rivets. Determine the correct rivet length and

diameter. Select and use the correct rivet set :for

specified rivet head styles.

Select and use bucking bars.

Remove rivets.

Determine the condition of a driven rivet.

Determine the circumstances under which 2117 rivets may be used to rep'lace 2017 and 2024 rivets.

Define rivet tipping.

Determine .the correct number of rivets to be used in making a structural sheet­ metal repair.

Handle and insball rivets that require heat treatment prior to use.

Adjust and use an air-operated riveting gun.

The circumstances under which type "A" rivets may be used in aircraft.

The mechanical properties of heat~trea.ted rivets.

Hand form, lay out, and bend sheet metal.-Level 3:

Make a joggle or offset bend.

Bend sheet metal that requires the use of a large radius.

Determine the neutral axis of a bend.

Define bend ra:dius.

Determine the amount of materia·! re­ quired to make a specified bend.

Bend sheet metal to a specified angle.

Lay out and bend a piece of sheet metal using a minimum radius for the type and thickness of material specified.

Lay out a bend in relationship to metal "grain" to minimize the possibility of cracking.

Determine the flat layout dimensions of a component part to be formed by bending.

Form metal by oumping.

E. WELDING.

Weld magnesium and titanium.-Level 1:

The method of cleaning magnesium in preparation for welding.

17

The main function of a flux while weld­ ing magnesium. The types of gases to use when gas-weld­ ing magnesium. The use of butt joints when gas-welding magnesium.

Solder stainless steel.-Level 1:

The use of silver soldering as a method of bonding meta:ls. The preparation of stainless steel for soldering.

The methods of cleaning material after soldering.

Fabricate tubular structures.- Level 1:

The types of tubing splices. The proper welding sequence to use when welding fuselage tubes.

The characteristics of a welded tubing joint.

The protection of the interior of tubular steel that is to be closed by welding. The method'S used to control distortion of steel tube structures during welding repairs. The preparation of tube ends for welding.

Solder, braze, gas-, and arc-weld steel.­ Level 2:

Use cleaning operations to prepare sheet steel for welding. .Ndjust oxyacetylene welding torch to

produce the type flame needed to weld a specified material.

'Select and use filler rod.

The effect of excessive heat on metal. Operate a portruble welding set. Select t'he correct size welding torch tip. The pre-cautions regarding welding over

a previou-sly brazed or soldered joint.

Solder a wire or cable to an electrical component. Sweat-solder a lap joint. Normalize a steel part after welding.

Identify steel parts considered oo be re­ . pairable by we'lding.

The preheating required prior to welding.

Weld aluminum and stainless steel.­ Level 2:

Use a filler rod when \velding aluminum with oxyacetylene.

Use flux when \veMing .aluminum. The purpose and effect of using inert gas

to shield the arc in certain types of welding.

F. ASSEMBLY AND RIGGING.

Rig rotary-wing aircraft.- Level 1 :

The condition of flight that a properly rigged aircraft should maintain. The relationship of thrust and drag of an aircraft during level unaccelerating flight.

The relationship of lift and weight of an aircraft during level unaccelerating flight. The meaning of the term "angle of attack" of an airfoil. The type of control movement used to

induce fol"w.ard flight in a helicopter. The method of controlling vertical flight of a helicopter.

The movement of an aircraft about its axes during normal flight maneuvers. The factors affecting stabi'l1ty of a,n air­ craft about its axes . The methods of maintaining directional

control of a helicopter. The ca,use and effect of rotor blade sta,ll

in helicopters operating at high speeds. The cause of vertical vibration in a two­ blade helicopter rotor system. The preparations required prior to rig­ ging. The method of tracking helicopter main rotor blades.

Rig fi.xed-wing aircraft.- Level 2:

The condition of flight that a properly rigged aircraft should maintain.

18

The factors to consider when rigging vertical stabilizer of single-engine, pro­

peller-driven aircraft. The rel'ationship of thrust and drag of an aircraft during level unaccelera.ting flight.

The effect of incorrect wing incidence angle.

The effect of dihedral on aircraft stability.

Use wing "wash-in" and ''w.ash-out" to

correct aircraft rigging.

The relationship 6f lift and weight of an aircraft during level unaccelerating flight.

The meaning of the term ''angle of at­ tack" of an airfoiL

The effect of fla·ps on aircraft landing speed and approach angle.

The meaning 6f the term ''incidence '8Jlgle" of an airfoiL

The movement of an aircraft about its

axes during normal flight maneuvers.

The relationship. between the center of pressure o£ a wing and its angle.of attack.

The factors affecting stability of an air­ craft aJbout its axes.

~he usual location of aircraft e.g. in re­ lationship to center of lift. The changes in lift and drag of the wings

when an aircra-ft is rolled about its longi­ tudinal axis.

The procedure for establiShing wing angle of incidence prior to repairing wing at­ tachment fittings.

Check alignment of structures.-Level 2:

Prepare fuse:lage for alignment check.

Check alignment of internally braced

wing structure. The significance and method of express­

ing reference positions.

Check alignment of assembled .aircraft.

Assemble air~raft.-Level 3:

The methods of safetying aircraft screws, bolts, and nuts.

Assemble, adjust, and safety caJble turn­ buckles.

The correct method of inserting bolts in aircraft fittings.

Insta:ll a.rrd inspect swaged cahle tenninals and fittings.

Balance and rig movable surfaces.­ Level 3:

The inspection requirements for cable­

operated primary flight control systems.

Handle and make up control ca:bles.

The corrosion protection requirements of control cables.

The effect of overtightening contro'l cables.

The relatiomthip between specified move­ ments of the cockpit controls and the con­ trol surfaces. The relationshitp between specified control movements during flight and t'he move­

ment of the aircraft about its axes. The movement of the controls, control surfaces, and the aircraft a!bout its axes during norm'al flight maneuvers.

Balance control surfaces after repair.

The relationship between specified nrove­ ments of the trim ta:b operating device and the trim mb.

Secure the cockpit flight contrd1:s in pre­ paration for control surface rigging.

The effect of a. worn pulley in a caMe­ operated control system.

The means used to reduce or prevent con­ trol surface flutter.

The purpose and operation of control surface locks. The purpose and operation of differential controls. The purpose and applicabi'lity of fair­ le'ads in a cable-operated control system.

Install and rig the cables in a flight con­ trol system. Splice control cables using Nicopress sleeves.

19

The probable causes of control surface flutter.

The maintenance requirements of control

surface trim tab systems. The purpose of counterweights incorporated in'to the leading edges of some •primary control surfaces. The purpose and function of "spring tabs" and "servo tabs".

Measure control surface movement and

adjust control stops.

The effect of temperature changes on control system -cable tension.

Assemble, adjust, inspect, and safety pushpull tube-type flight control systems.

The types and characteristics of cables used in aircraft primary control systems.

Jack aircraft.~Level 3 :

Determine maximum allowable jacking weight.

The use of correct capacity jacks.

Protect aircraft from damage during lifting and lowering operations.

Use ballast when jacking aircraft with engine removed;

The effects of wind when jacking aircraft.

G. AIRFRAME INSPECTION.

Perform airframe conformity and airworthiness inspections.~Level 3:

The maximum period of time an aircraft can be flown before an annual inspection

is required.

Determine the condition of airframes, airframe systems, and components.

The primary purpose of inspection.

The maximum time an aircraft that car­ ries passengers for hire or is used in flight instruction can be flown before being in­ spected.

Determine that an aircraft is in conform­ ity with FAA Specifications.

Determine that applicable Airworthiness

Directives have been complied with.

Co:n'duct a thorough and detailed inspection of an aircraft.

20

AVIATION MECHANIC AIRFRAME TEST

Section 2. Airframe Systems and Components

A. AIRCRAFT LANDING GEAR SYS·

TEMS.

Inspect, check, service, and repair landing gear, retraction systems, shock struts, brakes, wheels, tires, and steering systems. -Level 3:

Determine .aircraft tire inflation pressures.

The factors affecting the retreading of aircraft tires. Adjust landing gear toe-in.

Install and remove aircraft wheel and brake assem:blies.

Insta;ll tu:bes and tires.

Protect aircraft tires from hydraulic fluids.

Service brake dehoosters.

Service landing gear shock struts.

The effects of increasing temperature on "parked" brakes.

Determine the cause of an oleo strut bot­ toming during taxi operations. The pressure source for actuating power brakes.

Select and install air valves in oleo shock struts.

Observe safety precautions when de­ mounting tire and wheel assemblies. Determine if a brake system requires bleeding; perform brake system b-leeding.

Inspect and adjust multiple-disc brakes.

Install new linings in hydraulically oper­ ated single-'disc brakes. Determine the cause of spongy brake action. Inspect and service .aircraft tires and tubes.

Determine the reason for "dragging"

brakes. The method of equalizing braking pres­ sure on both sides of the rotating disc of a single-disc brake. Operate and check retractable landing gear. Determine the cause of fading brakes. Replace actuating cylinders.

Install brake blocks in an expander-tube brake assembly.

Inspect brake drums. The purpose and function of metering pins in oleo shock struts. Determine the cause of excessive brake pedal travel. The operating princip~es of oloo shock struts during landing. The storage requirements for aircraft

tires and tubes. The effect of a broken return spring in a brake master cylinder.

Determine the cause of grabbing brakes. The pul"pose and operation of a d~booster in a hydraulic power brake system. Detect internal leakage in a brake master cylinder.

The operating principles of servo) ex­ pander-tube, multiple~disc, and single-disc aircraft brakes. The pul"pose and operating principles of brake master cylinders. B. HYDRAULIC AND PNEUMATIC POWER SYSTEMS. Repair hydraulic and pneumatic power system components.-Level 2:

Install packing seals and rings on hydraulic components.

21

Determine the correct seal type to use

with ester-base, petroleum-base, and vegetable-base fluids.

Remove .and install hydraulic selector valves.

Remove and install a spool-type or balanced-type pressure regulator.

Determine the cause of excessive oil in an aircraft pneumatic power system.

The operating principles of a pneumatic power system multistage reciprocating compressor.

Identify hydraulic seals and pa:ckings.

Protect packing rings or seals against thread damage during installation.

Identify and select hydraulic 1luids.­ Level 3:

Determine the fluid type for use in a specified aircraft hydraulic system.

The method of ·measuring the viscosity of a liquid.

Identify ester-base, petroleum-base, and vegeta.ble...base fluids.

Inspect, check, service, troubleshoot, and repair hydraulic and pneumatic power systems.-Level 3:

Determine the air pressure in a hydraulic accumulator.

The location and use of quick-disconnect fittings in hydraulic and pneumatic sys­ tems.

The mounting position of diaphragm and bladder-type hydraulic accumulators.

Service hydraulic reservoirs.

Determine the causes of incorrect system pressure.

Service porous paper and micronic filter­ ing elements.

Adjust the pressure setting of the mam system relief vrulve.

Purge air from a hydraulic system.

The term used to indicate force per unit area.

Identify the types of hydraulic power systems.

The purpose, location, and operation of

a hydraulic fuse.

Protect a hydraulic system against contamination during a component replacement.

Inspect a hydraulic system for water and metal contamination.

Service a pneumatic system moisture separator.

The purpose, location, and operation of an orifice check valve in the wing flap

actuating system. . The purpose, location, and operation of

a wing fl.a·p overload valve.

The purpose, location, and operation of

a hydraulic system pressure regulator.

The purpose, location, and operation o:f a sequence valve.

The purpose, location, and operation of

a crossfiow valve.

The purpose, location, and operation of

a hydraulic system pressure accumulator.

The purpose, location, and operation of a shuttle valve.

The purpose, location, and operation o£ a check valve.

Install and remove engirie-driven hydraulic pumps.

The indications of a worn or damaged hydraulic pump shaft.

The operating prin-ciples of hydraulic hand pumps.

The cause of hydraulic pump chatter during operation.

The operating principles of a constantdisplacement hydraulic pump.

The operating principles of a variabledisplacement hydraulic pump. The purpose of the shear section on the shaft of an engine-driven hydraulic power pump.

22

The purpose and operation of a hydraulic actu'a..ting cylinder.

Determine the cause if a constant-pressure

hydr~ulic system with no external leakage

will not hold pressure when the power pump is not operating.

Determine the cause if an engine-driven power pump will not maintain system

pressure during t'he actuation of a unit in the system. The general features and operating principles of aircraft pneumatic power systems.

The purpose of pressurized reservoirs in some hydraulic systems.

The purpose and location of a standpipe

in some hydraulic reservoirs.

The causes of too frequent cycling of a constant-pressure hydraulic system.

Operate and check a hydraulically aperated flap system. The operating mechanism of most hy­ draulic pressure gauges. The indications of a low fluid supply during system operation.

C. CABIN ATMOSPHERE CONTROL SYSTEMS. Repair heating, cooling, air-conditioning, pressurization, and oxygen system components.-Level 1 :

The usual reasons a surface combustion heater fails to operate. The effects of cracks or holes in an exhaust-type heat exchanger. The usual sources of contamination of a freon system. The method of protecting a freon system from contamination during replacement of a component. Inspect, check, troubleshoot, service, and repair heating, cooling, air-conditionipg,

and pressurization systems.-Level 1:

The operating principles of a thermo­

statically controlled surface combustion heater.

The methods used to control cabin pressure of a pressurized aircraft. The protective features included in the control circuits of surface combustion

heaters. The purpose and operation of check

valves in the delivery air ducts of a pressurization system. The basic principles of providing and contro'lling aircraft pressurization. The inspection requirements of cabin heating systems that utilize an exh:aust

heat exchanger as a source of heated air.

The method of checking a oombustion heater fuel system for leaks. The function of t:he condenser in a freon cooling system. The function of the evaporator in a freon cooling system.

The function of an expansion valve in a freon cooling system.

The location, in relationship to each other, of the units in a freon cooling system. The method oi determining the liquid level in a vapor-cyde cooling system. The procedure for servicing a V'ILpor-cycle air-conditioning system that has lost all its freon charge. The basic operating principles of an aircycle cooling system.

The function of a jet pump in a pressurization and air-conditioning system. The function of ·a mixing valve in an airconditioning system. The function of the negative pressure­

relief valve in a pressurization system. The function of the outflow valve in a

pressurization system. The function and principles of operation of an automatic ca:bin rate-of-climb control system.

Inspect, check, troubleshoot, service and repair oxygen systems.-Level 2:

Check oxygen system for leakage.

23

Service oxygen system with breathing oxygen.

Inspect a breathing oxygen system for contamination.

D. AIRCRAFT INSTRUMENT SYS­ TEMS. Inspect, check, service, troubleshoot, and repair heading, speed, altitude, time, attitude, temperature, pressure, and position indicating systems.-Level 1:

The procedure fur "swinging" an aircraft rn.agnetic compass.

The meth'Ods used to test a static air sys­

te~ for leakage.

The significance of various types of marks on the face of an instrument.

The operating princi!ples of a themlocoup'le temperature-indicating circuit. The service requirements of instrument system filters.

The effect of a ruptured or disconnected static pressure line located inside a pressurized cabin.

Install instruments.- Level 2 :

The installation and connection of shockmounted vacuum instruments to their power system. The types of hardware used to install instruments. The application of operation markings to the glass face of an aircraft instrument.

The protection of instruments during handling. The installation practices necessary to prevent damaging an instrument.

The installation practices used in making hose or tubing connections to the instru­ ments.

E. COMMUNICATION AND NAVIGA·

TION SYSTEMS. Inspect, check, and service autopilot and approach control systems.-Level 1 :

The operating principles of the sensing

device used in an autopilot system.

The purpose and operation of the autopilot.

The purpose of a servomobor in an autopilot system.

The insta:ll'ation requirements for auto­

pilot units.

The function of a position transmitter in an autopilot system.

Inspect, check, and service aircraft elec· tronic communication and navigation sys­

tems.-Level 1:

The FCC regulations pertaining to the operation of two-way radio.

The principal conditions which must be oonsidered in the insta!llation of radio.

The protection of radio equipment from

shock and vibration.

The methods of reducing engine noise in radio receivers.

Inspect and repair antenna and electronic equipment installations.-Level 2:

The preferred location and methods of mounting external antennas.

The procedure for returning an aircraft to service after a radio installation has been made in accordance with approved installation data.

The preferred location for the VOR localizer receiver antenn'a on a sma.l[ aircraft.

F. AIRCRAFT FUEL SYSTEMS.

Check and service fuel dump systems.­ Level 1:

The reasons for requiring fuel dump systems.

The methods used to control the operation of fuel dum'p ~hutes and valves.

The principal safety requirements for a fuel dump system.

The purpose of jettison pumps in fuel dump systems.

24

Perform fuel management, transfer, and defueling.-Level 1:

The precautioPc; required when defueling an aircraft. The tank-to-engine combinations possible

with a crossfeed system.

The method of maintaing e.g. limits

using fuel transfer technique. The arrangement of fuel system controls,

indicators, and warning lights.

Inspect, check, and repair pressure fueling systems.-Level 1:

The method of controlling fuel level during pressure fueling operations. The methods used to operate fueling valves. The protection of integral tanks against overpressure during pressure fueling operations. The arrangement of fueling system contrdls, indicators, arrd warning lights. The precautions required when fueling an aircraft. The purpose and operation of pilot valves.

Repair aircraft fuel system components. -Level 2:

Repair and seal fuel tanks. Pressure test fuel tarrks.

Remove and clean fuel strainers. The precautions to follow when routing

fuel lines. The method of regulating fuel system pressure.

Inspect and repair fluid quantity indicating systems.-Level 2:

The methods used to determine the level of fluid in a tank. The purpose of remote-reading electrica:l gages. Calibrate liquidometer-type fluid quantity indicating systems. The effect of aircraft attitude on fluid

level measuring devices.

Troubleshoot, service, and repair ftuid pressure and temperature warning systems. -Level2 :

Determine and adjust the pressure or

temperature at which warning systems operate. Determine the cause of incorrect warning system indications and make corrections. Test the operation of temperature and pressure warning systems. Inspect, check, service, troubleshoot, and repair aircraft fuel systems.-Level 3:

The fuel system inspection requirements for aircraft operating in areas of high humidity or wide temperature changes. The design and installation requirements

for aircraft fuel tanks. The maintenance requirements of fuel

tank sumps. The marking requirements for fuel filler

openmgs. The purpose o£ 'potassium dichromate in a fuel system. The reason for using booster pumps with engine-driven pumps. The purpose of baffte plates in fuel tanks. The installation and operation require­ ments of fuel valves. The venting requirements of intercon­

nected fuel tanks.

G. AIRCRAFT ELECTRICAL SYSTEMS.

Repair aircraft electrical system components.-Level 2:

Use a "growler" in generator and motor armature inspection and repair. Check the condition of shunt and com­

pound generator field circuits. Locate and use overhaul information for electrical equipment. The procedures for correcting generator brush arcing. Dress or turn the commutator surface of

a motor or generator armature. Flash a generator field.

25

The effect of changes in speed and load on generator output.

The function of a commutator in a direct

current electric motor.

Seat new or replacement generator brushes. The effect of incorrect generator brush spring tension on generator operation.

The methods of reducing armature reac­ tion in aircraft generators. The operating principles of carbon-pile

voltage regulators. The design factors that determine the

number of cycles-per-revolution an alter­ nating current generator will produce..

Determine the speed (r:p.m.) of an elec­ tric motor. The basic principles of generators. The factors that affect the torque pro­

duced by an electric motor. The methods used to protect armature shafts from overloads.

The speed and loa:d characteristics of series-, compound-, and shunt-wound motors. The means employed to control current

and voltage output of aircraft generators.

The methods used to control output fre­ quency and voltage of alternating current

generators. The general operating characteristit'lS of vi!brator-type current and voltage regu­ lators.

The purpose and operation of reverse­ current cutout relays in generator control circuits.

The basic internal electrical circuits of

series-, compound-, and shunt-wound gen­ erators.

The operating principles of magnetic

clutches and brakes commonly used with electric motors.

Instant check, and service airframe electrical wiring, controls, switches, indicators, and protective devices.-Level 3:

The purpose, applicability, and operation of electrical fuses and circuit breakers.

The types and operation of electrical switches.

Install and wire electrical switches.

Splice wiring in aircraft electrical systems.

The characteristics of high-tension and low-tension electrical wiring.

The purpose, applicability, and use of electric·a.J wiring terminal strips.

The criteria for selecting aluminum and copper electrical cables.

Replace terminals on aircraft aluminum and copper electrical cables.

Determine the curren:t-ctt.rrying capacity of an electrical circuit. ­

The installation and maintenance of open wiring electrical systems.

Install electrical Wiring in conduits.

The metliod of protecting electricaUy op­ erated emergency systems from accidental actuation.

The strength requirements for electrical cable terminals.

Select and install electrical bonding jumpers.

The instaUation requirements for electri­ cal junction boxes.

The characteristics of single-wire electri­ cal systems.

The special requirements an electrical bonding jumper must meet if it is re­ quired to carry a ground load for a unit of electrical equipment.

The purpose of shielding electrical wiring and equipment.

The purpose and operation of reversible The use of quick-disconnect electrical electric motors. plugs and sockets.

26

The purpose of static wicks or dischargers.

The American Wire Gage (A.W.G.) system of designating electrical wire sizes.

Inspect, check, troubleshoot, service, and repair alternating current and direct current electrical systems.-Level 3:

The results of short or open circuits in a generator control circuit.

The effect of sticking points in a reversecurrent cutout relay.

The cause and effect o:£ solenoid switch chatter.

The installation and circuit requirements

for anticollision light systems.

The installation and circuit requirements

for position lights.

The method of providing direct current

for battery charging on aircraft that operate only alternating current generators.

The common methods of controlling output current and voltage of compound di­

rect ctirrent generators.

The operating principles and characteris­

tics of inverters.

Determine the output frequency of an alternating current generator.

The operating principles and character­

istics of rectifiers.

The method of providing alternating current in aircraft that operate only direct

current generators.

The electrical device usually used to convert alternating current to a ·lower or higher voltage without a change in fre­

quency.

The operating principles and eharacter­

istics of electrical induction coils.

The operating principles and character­

istics of transformers.

The advantages of using alternating cur­

rent in aircraft.

H. POSITION AND WARNING SYS­

TEMS.

Inspect, check, and service speed· and takeoff-warning systems, electrical brake controls, and antiskid systems.-Levell:

The general requirements for installing skid detectors.

The operating principles of hydraulic brake antiskid systems.

Inspect, check, troubleshoot, service, and repair landing gear position indicating and warning systems.-Level 3:

Determine the cause of a gear unsafe warning signal.

The effect of various electrical faults in

the operation of the landing gear warning system.

I. ICE AND RAIN CONTROL SYSTEMS.

Inspect, check, troubleshoot, service, and repair airframe ice and rain control systems.-Level 2:

Install deicer hoots. The operating principles of anti-icing

systems that utilize heated air in the leading edges of airfoils and intake ducts.

The operating principles of electrically operated anti-icing systems. Protect deicer boots from deterioration.

J. FIRE PROTECTION SYSTEMS.

Inspect, check, and service smoke and carbon monoxide detection systems.-Level 1: The operating principles of smoke and carbon monoxide detection systems.

Inspeet, check, service, troubleshoot, and repair aircraft fire detection and extinguishing systems.-Level 3:

The type of fire-extinguishing agent most

suitaJble for use with electrical fires. The fire-extinguishing agent normally used with built-in aircraft fire-extinguishing systems.

27

Check fire extinguisher container pressure. Determine the cause for the system failing to function. Check continuity and resistance of the Check fire 'Yarning sensors or detectors

ele~trical circuit. for open or short circuits.

28

AVIATION MECHANIC POWERPLANT TEST

Section 1. Powerplant Theory and Maintenance

A. RECIPROCATING ENGINES.

Inspect and repair 14-cylinder or larger radial engine.-Level 1:

The purpose and advantages of using

propeller reduction gearing.

The characteristics of thrust bearings used in large radial engines.

The characteristics of crankshaft bearings used in large radial engines.

The construction characteristics of the

crankshaft and rod assemblies for a tworow radial engine. The loads acting on the power case and nose case of a large radial engine during various conditions of operation.

The methods of classifying r-eCiprocating engines.

The factors that affeot the volumetric efficiency of an engine.

Determine the cylinder firing order for

various types of engines.

Overhaul reciprocating engine.-Level 2:

The purpose and operating principles of

dynamic dampers used in aircraft engines.

The characteristics of various crankshaft designs.

The basic operating principles of fourstroke cycle engines.

The characteristics of various piston pin and knuckle pin retention devices.

The processes used to harden cy Iinder bores. The purpose and applicability of choke­ type or taper-ground cylinders.

The wear characteristics of engine cylinder walls.

The purpose of valve overlap in some engines. The effects o£ various poppet-type valve

face angles. The characteristics of various types of valve operating mechanisms. The operating characteristics of zero-lash hydraulic valve lifters. Time engine valves during engine as­ sembly. Install valve guides. Grind and resurface valves and valve seats. The purpose of using relatively large piston-to-cylinder wall clearances in air­

craft engines. The indications of failed or failing engine bearings. The result of operating an engine at high power settings before the lubricating oil has come up to operating temperature.

Check piston rings for correct end and side clearance. Check valve stems for stretch. Repair a scored aluminum piston. Perform crankshaft "runout." Prepare engine for disassembly before overhaul. Measure inside diameter, taper, and out­ of-round of a cylinder bore. Install cylinders and tighten holddown

nuts. The construction characteristics of air­

cooled engine cylinders.

The construction characteristics and the operating principles of poppet-type engine valves.

29

The construction characteristics of aircraft engine pistons. The types and arrangements of piston

rings used in aircraft engines.

The purpose of using more than one spring on aircraft engine valves.

The operating principles and construction of spur and pinion-type and planetary­

type propeller reduction gearing.

The principles of construction and operation of accessory gear drive trains on reciprocating engines.

Inspect cast and forged engine crankcase

assemblies.

Remove and install studs in engine crankcase and accessory sections.

Inspect, check, service, and repair opposed and radial engines and reciprocating engine installations.-Level 3:

Check and adjust engine valve clearances. Determine the speed and direction of rotation of the cam ring in various radial

engines.

The·effect of excessive or insufficient valve clearance on engine operation.

The relationship between operating valve

clearance and cold valve clearance.

Perform cylinder compression tests.

Perform an ignition system operational

check.

Determine the condition of cable-operated engine control systems.

Check and adjust engine idling spel'ld and mixture.

Detect and determine the cause of a "cold" cylinder.

The purpose of establishing one or more critical ranges for certain engine-propeller combinations.

The operating indications of a worn or

weak engine.

The effect of a leaking oil dilution valve

on engine operation.

The effect of a low oil supply on engine operation. The indications of a correctly functioning engine oil system. The probable cause of oil being thrown out of the breather of a wet-sump engine.

Determine the source and cause of metallic particles found on the oil screen during

engine inspection. The effect of an unbalanced propeller on engine operation. The power settings most desirable for

protracted engine operation. Dilute engine oil in preparation for cold

weather starting operations.

The purpose and operating principles of engine dynamic suspension systems. Install and time a magneto.

Install, troubleshoot, and remove reciprocating engines.-Level 3:

The effect of throttle position upon fuelair mixture in the cylinders during startmg. Pre-oil an overhauled engine before start­ ing.

Install air-cooled engine baffies. The method of hoisting or lifting engines during removal and installation.

The effect of increased engine manifold pressure on master rod bearing load. The effect of air density on engine power output. The causes of engine backfire. The basic operational sequence for in­

creasing or reducing the power output of an engine equipped with a constant-speed propeller. ·The factors that affect an engine's tend­ ency to detonate. The effect of induction system air leaks on engine operation. The indications of a leaking primer sys­ tem during engine operation.

30

The effect of e:x:ha.ust back pressure on

engine power output.

The result of incorrect ·fuel-air mixture adjustments. The indication and effect of carburet{)r

-~mg. Operate and adjust mechanical push-pull control systems.

B. TURBINE ENGINES.

Overhaul turbine engine.-Level 2:

The relationship between rotor speed and total thrust of a turbine engine.

The relationship between turbine inlet temperature and thrust of a turbine engine.

The relationship between operating alti­ tude and thrust of a turi>ine engine. The operating characteristics of turbine

engines equipped with two-spool or "split" compressors. The operating characteristics of fan and bypass turbine engines. The relative gas pressures in various por­ tions of a turbine engine. The function of the nozzle diaphragm in

a turbine engine. The function of the exhaust cone in a turbine engine.

The operating charact~ristics and types of combustion chambers. Remove and install outer combustion­

chamber case and liners. The metho'ds for disassembling compres­ sor sections. The function and location of fuel nozzles.

Inspect, check, service, and repair turbine engines and turbine engine installations.­ Level 2:

The principles of operation of thrust re­

versing systems used with turbine engines. The advantages of a gas turbine geared

to a propeller.

The types of compressors most commonly used in turbine engines.

The construction and operating charac­ teristics of axial-flow compressors.

The advantages of the axial-flow com­ pressor over the centrifugal compressor.

The function and location of the diffuser section. The basic design of turbine blades.

The effect of high ambient temperatures

on turbine .engine operation. The type failures to which turbine com­ ponents are subject. The results of excessive operating tem­

perature.

Install, troubleshoot, and remove turbine engines.-Level 2:

The operating ·principles of a turbine engine. The effect of air density on the thrust of

a turbine engine.

The effect of exhaust nozz'le adjustments on turbine engine operation.

The method of controlling compressor surge. The purpose and operation of fuel con­ trol devices.

The cause of hot spots on the outer combustion casing. The met hod of insuring ignition in com­ bustion chambers rrot equipped with ig­ niter plugs.

Adjust turbine engine fuel controls.

C. ENGINE INSPECTION.

Perform powerplant conformity and airworthiness inspections.~Level 3 :

Determine that applicable Airworthiness Directives are complied with.

Determine that the powerplant conforms with the applicable FAA Specification.

31

AVIATION MECHANIC POWERPLANT TEST

Section 2. Powerplant Systems and Components

A. ENGINE INSTRUMENT SYSTEMS.

Troubleshoot, service, and repair fluid rate-of-flow indicating systems.----Lev~l 2:

The purpose· and operating principles of a fuel-flow indicating syostem. The relationship between fuel .flow and

the power output of an engine.

Inspect, check, service, troubleshoot, and repair engine temperature, pressure, and r.p.m. indicating systems.-Level 3:

The operat'ing ·principles of thermocoupletype temperature indicating systems.

The effect of a broken or leaking manifold pressure gage line. The purpose an'd operating principles of

an exhaust gas .ana1yzer system.

The purpose and operating principles of a manifold pr~ure indicating system.

The operating principles of engine oil temperature indicating systems.

Apply m'arkings to the glass face of en­ gine instruments.

Install tachometer drives. Determine the reason for failure of an

electric tachometer system. The requirements for a carburetor air temperature indicating system. Determine the reason for an off-scale

reading of a ratiometer-type indicating system.

Determine the cause of erratic indications when using a thermocouP'le system.

The purpose and operating principles of

fuel pressure warning systems.

The installation practices for thermo­ couple leads.

The operation and use of sync:hronous motors.

Measure the resistance of thermocouple

leads.

Determine the cause of .an inverse reading in a thermocouple temperature indicating system.

Identify the types and application of thermocouples used to indicate turbine engine temperatures.

B. ENGINE FIRE PROTECTION SYS­

TEMS. Inspect, check, service, troubleshoot, and repair engine fire detection and extinguishing systems.-Level 3 :

Check continuity and resistance of the

electrical circuit.

Determine the causes oi system malfunction. The methods used to release the extin­

guishing agent. The sensing devices used in the detection

systems.

C. ENGINE ELECTRICAL SYSTEMS.

Repair engine electrical system components.-Level 2:

Check the condition of shunt ami compound generator .field circuits. Locate and use overhaul information for electrical equipment. The procedures for correcting generator brush arcing. Check a motor or generator armature to determine that the windings are not grounded. Smooth the commutator surface of a mo­ tor or generator a.rmature.

33

Determine the cause of solder deposits on Determine the output frequency of an althe armature cover plate of a generator. ternating current generator. The purpose of a ripple filter in a gen­ erator power circuit.

The type of electric motor used with

direct-cranking engine starters. The types of voltage regulators used with high output direct current generators.

The results of short or open circuits in a generator control circuit. The effect of sticking ·points in a reverse­ current cutout relay. The method of providing and controlling the field current of a.ircraft generators. The methods of controlling parallel direct current generators. The .methods used to control output fre­ <Juency and voltage of alternating current

generators.

The methods of reducing armature reac­ tion in aircraft generators. The metho'ds of controlling current and

voltage output of compound direct current gene;mtors. The operating principles of -carbon-pile V'Oltage regula.tors. The operating chara·cteristics of series~ wound direct current elootric motors.

The purpose and ·operation of reverse­ current cutout relays in generator control circuits.

The general operating characteristics of vibra.tor-type current and V{)}tage regu­ lators.

Flash a generator field. The effect of changes in speed and load

on generator output. The design factors t:hat determine the

number of cycles per revolution an alter­ nating current generator will produce.

The factors that affect the torque pro­ duced by an electric motor. The function of a commutator in a direct current electic motor.

The methods used to protect armature

shafts from overloads.

Seat ne'v or replacement generator brushes.

The effect of incorrect generator bruS'h spring tension on generator operation.

The speed and loa.d characteristics of

series-, compound-, and shunt-woun'd electric motors.

The basic principles of electric generators.

The basic internal electrical circuits of

series-, compound-, and shunt-wound generators. The applicability and use of intermittentduty·· electric motors.

The operating principles of magnetic clutches and brakes ·commonly used ·with electric motx>rs. The requirements and methods for controlling a malfunctioning generator.

The purpose and operation of reversible electric motors.

Install, check, and service engine electri· cal wiring, controls, switches, indicators, and protective devices.-Level 3:

The purpose, applicaJbility, and operation of electrical fuses and circuit breakers.

The types of electrical switches and their operation. Install and wire electrical switches.

Splice wiring in engine electrical systems.

The characteristics of high-tension and low-tension electrical wiring.

The purpose, appli\lability, and use of

~lectrical wiring terminal strips. The criteria for selecting aluminum and copper electrical cables.

Replace terminals on aircraft aluminum and copper electrical cs:bles.

Types of switches and circuits used to control reversible electric motors.

34

Identify aircraft electric cables. Determine the current-carrying capacity of an electrical circuit.

Install electrical wiring in conduits. Use electric cable selection chart for determining the corre:ct ca'ble to use in specified circumstances.

The strength requirements for electric cable terminals. Select and install electrical bonding jumpers. The installation requirements for electri­ cal junction boxes.

The installation and wiring o£ solen'Oid­

operat~d switches.

The chara-cteristics of single-wire electrical systems. ·

The use of quick-disconnect electrical plugs and sockets.

The American Wire Gage (A.W.G) sys­ tem of designating electrical wire sizes.

The cause and effect of sdlenoid sw.itch chatter.

T·he method of providing dire·ct current

for tbattery charging on aircraft that op­ erate only alternating current generators.

The maximum permissible continuous load on the electrical system.

The sources of alternating current power in aircraft that operate only direct cur­

rent generatoTS.

The operating principles and character­ istics of transformers. Determine the approximate continuous load on an aircraft electrical system.

D. LUBRICATION SYSTEMS.

Identify and select lubrieants.-Level 2 :

The desirable characteristics for aircraft engine lubricating oils.

The meaning and importance of oil viscosity.

The meaning and significance of oil flash point.

The purpose of using synthetic lubricants

for turbine engines. The effect of heat on lU'bricants. The grade designations for aviation oils. The designations for synthetic turbine oil.

The results of operating an engine using an incorrect lubricant.

The functions of engine oil in addition to lubricating the engine.

Repair engine lubrication system components.-Level 2:

Clean and repair aluminum alloy external oillines. ·

Clean external lubrication system components. The function and location o£ an oil temperature regulator. The size requirement for the oil inlet line.

Clean and test oil tanks. The ·purpose and operation of the oil cooler. The operating principles of lubrication pumps.

Inspect, check, service, troubleshoot, and repair engine lubrication systems.- Level 3:

Determine source and cause of metailic particles in the lubricating oil. The purpose and principles of operation of engine oil dilution systems. The expansion space requirements for engine oil supply tanks.

The purpose for changing engine lubricating oil at specified intervals.

The type of lubrication system generally used in high-volume reciprocating engines. The factors that affect the oil consumption of a reciprocating engine. The method normally used to prevent excessive oil from accumulating in the cyl­

inders of inverted engines or the lower cylinders of radial engines.

The method of controlling the oil film on cyliilder walls.

35

The method of lubricating the valve­

operating mechanism in an overhead­ valve engine. The venting requirements of dry-sump and \vet-sump engine lubrication systems.

The effect of broken or leaking lines in various ·parts of the lubrication system. The effect of engine wear on the opera­ tion of the lubrication system.

The operati."lg indications of a low engine oil supply. The method of maintaining a reserve sup­ ply of oil in the engine oil supply tank for use in -propeller feathering. The requirements for marking oil tank fillers. The purpose and operating principles of the lubrication system pressure-relief valve. The purpose and operation of the oil cooler bypass valve. The effect of congealed oil in the heat exehange portion of an oil radiator. The purpo~e, location, and operation of

anti-sludge chambers in the lubrication system of a reciprocating engine. The purpose and operation of the bypass 'feature built into most engine oil filtering

systems. The operating principles of the stacked 'disc, edge filtration type of filter. The characteristics and operating prin­ ciples of dry-sump and wet-sump engine lubricating systems. The purpose, location, and operation of

the oil separator. Adjust engine oil pressure. The purpose of the restricted orifice in the oil pressure gage line. The effect of obstructed rocker box inter­ cylinder oil drain lines on engine oper­ ation. The characteristics and principles of op­ eration of a radial engine oil scavenging

system.

E. IGNITION SYSTEMS.

Overhaul magneto and ignition harness.­ Level 2:

The construction characteristics of mag­

neto main case housings.

The characteristics and construction ma­

terials of magneto pole shoes or coil core extensions. The purpose and methods of ventilating aircraft magneto hou'sings. The materials used in the construction of magneto breaker points. The purpose and use of "keepers" placed across the poles of a rotating magnet that

has been removed from a magneto. Check the strength of a rotating magnet

installed in a magneto. ·

Internally time a magneto during as­ sembly. Determine the rotational speed of a mag­ neto when installed on various types of

engmes. The purpose and location of condensers

in a magneto electrica:l circuit. Determine the condition of magneto breaker points by visual indications.

Lubricate a magneto breaker cam. The effect of cam-follower wear on pivot­ and pivotless-type breaker-·point assem­ blies. The meaning of the term "E-Gap Angle." The characteristics of the rotating mag­

nets commonly used in aircraft magnetos.

Install and adjust breaker points. The characteristics of cams used in air­ craft magnetos to operate the breaker points. The purpose of settmg ignition ca:bles in a plastic insulating material -within some ignition harnesses. Install high-tension ignition cables in a. shielded ignition manifold. The purpose and operation . of impulse couplings used with aircraft magnetos.

36

The results of operating a magneto with a broken impulse coupling spring.

The methods used to secure ignition leads in harnesses and distributor blocks.

Measure breaker point spring tension.

Repair engine ignition system components.-Level 2:

The purpose and operation of magneto breaker points.

Measure the capacity o£ a condenser. Check ignition coil windings for shorts

or open circuits.

Lo'cate and use data associated with igni­ tion system components. The effect of weak magnets on engine operation.

The effect of weak breaker point spring

tension on engine operation.

Clean and inspect spark plugs and igniter plugs. Adju:st spark plug electrodes. The precautions to c>bserve when working

with high~energy ignition systems.

Determine that a distributor is internally timed.

The effect of high resistance in an igni­ tion lead on engine operation. The function and characteristics of igni­ tion harnesses.

Determine the continuity of ignition w1rmg.

The construction and operation of a trans­ former coil for low-tension ignition sys­ tems.

Inspect, check, service, troubleshoot, and repair reciprocating and turbine engine ignition systems.-Level 3:

The purpose of shielding aircraft engine ignition systems. The purpose ·and principles of staggered

~anition timing.

Install and time an ignition system dis­ tributor.

Recognize and interpret basic ignition

analyzer patterns.

The purpose and operating principles of spark advance systems.

The effect of using condensers of incorrect capacity in an ignition system. The operating principles of low-tension

ignition systems. The effect a shorted primary winding in

a low-tension ignition coil has on engine operation.

Install and test magneto ignition switches.

Test an ignition harness for electrical leakage.

The purpose and principles of compen­ sated ignition timing.

The operating periods of turbine engine

ignition systems. The results of using a spark plug oi in­

correct heat range in an engine.

Install and remove spark plugs.

The meaning of "reach" as applied to

spark plug design.

Inspect spark plugs for damaged insulation. The cause and effect of various types of spark plug fouling. The purpose and operation of an ignition booster system. The purpose and operation of an induc­ tion vibrator.

Install and time a magneto equipped with an impulse eoupling.

F. FUEL METERING SYSTEMS.

Inspect, check, and service water injection systems.- Level 1 :

The purpose and effect of injecting water or water-alcohol during periods of high

engine power output. The means used to prevent the freezing

of the water or ADI liquid.

The effect of atmospheric humidity on engine power when using water injection.

37

The effect of exhausting the water supply during takeoff operations utilizing water

injection.

The purpose and effect of the derichment valve in the water~alcohol injection system.

The results of detonation within an engine.

The procedure to follow when detonation

occurs. The factor that determines the amount of water flow during ADI operation.

The method for preventing corrosion of lines and fittings used in ADI systems.

The purpose of the oil-pressure-operated

valve in the ADI system.

Overhaul earburetor.-Level 2:

The fuel metering forces of a conventional float-type carburetor and a pres­ sure-type carburetor.

The rel.&tionship between carburetor ven­ turi size and. engine displacement volume.

The fuel-air mixture requirements of an

engme during idling and during high power settings.

The operation of the idling system of a float-type carburetor and a pressure-type carburetor.

The effect of a. clogged main air ·bleed in a float-type carburetor on engine opera­

tion.

Check and adjust the float level of a floattype carburetor.

The effect of an incorrectly adjusted float level on engine operation.

The effect of a worn or grooved needle valve and seat assembly in a float-type carburetor on engine operation.

The operating principles of a back-suction-type mixture control.

The operating principles of an automatic mixture control.

The operating principles of economizer systems in float-type carburetors.

The effect of a ruptured diaphragm in a pressure-type carburetor on engine oper­

ation. ·

The basic function of a manual mixture control in an aircraft carburetor.

The location and operating principles of discharge nozzles used with pressure carburetors.

Repair engine fuel metering system components.-Level 2:

The operating principles of piston-type and singleand double-diaphragm acceleration pumps.

The operating principles of direct fuel

injection systems.

The purpose and operation of a venturi. The function of a metering jet.

The purpose of an air bleed in a carbu­

retor.

·The purpose of an economizer valve in a carburetor.

Clean carburetor parts.

Repair a. leaking float.

The adjustments that may be made on a

pressure-injection carburetor.

The effect of clogged impact tubes on engine operation.

The function of the synchronizer bar on

fuel injection equipped engines. The function and operation of the ma.in and idling air bleed systems in a float­ type carburetor.

Inspe_ct, check, service, troubleshoot, and repair · reciprocat'ing and turbine engine fuel metering systems.-Level 3:

Adjust idling speed and mixture.

The principles of operation of an auto­ matic fuel control unit used on a turbojet engine.

Trim turbojet engine fuel control systel!l.

The effect of increased altitude on engine fuel-air mixture.

38

The relative burning rates of various fuel­ air mixtures.

The fuel-air mixture requirements of a

reciprocating engine at various power settings. The operating characteristics of engines

with direct cylinder fuel injection systems.

Install, remove, and adjust direct cylinder fuel injecthm system components.

The difference between a fuel injection system and a fuel injection carburetor.

The cause of lean mixtures in a conven­ tional carburetor system. The effect an inoperative vapor vent in a pressure-type caflburetor has on engine operation.

The factors that affect the density of the

air entering the cal.'lburetor.

G. ENGINE FUEL SYSTEMS.

Repair engine fuel system components.­ Level2:

The types of engine-driven fuel pumps

generally used with large reciprocating engines. The purpose and operation of a fuel pump bypass valve.

The purpose and operation of fuel boost

pumps.

Inspect, check, service, troubleshoot, and repair engine fuel systems.-Level 3:

The causes of fuel pres!:)ure fluctuation.

The characteristics of centrifugal-type fuel boost pumps.

The fuel system requirements for aircraft certificated in the "standard" classification.

The usual sources of aircraft fuel system contamination. The purpose and requirements for strain­ ers in fuel tank outlets.

Inspect aircraft fuel tank sumps and fuel strainers. Adjust engine-driven fuel pump output

pressure.

The location and operation of main tuel strainers.

The causes and effects of fuel system vapor lock.

The location and operation of fuel valves.

H. INDUCTION SYSTEMS.

Inspect, check, troubleshoot, service, and repair engine ice and rain control systems. -Level2:

The principles of alcohol injection to control induction system icing.

The effect of ice within the induction system on engine operation.

The operating principles of carburetor air heaters used to prevent or eliminate ice

in an engine induction system.

The method used to prevent the entry of rain into the induction system of a re­

ciprocating engine.

The operating principles of electrically heated inlet ducts. The use of engine bleed air to control engine inlet icing. The causes of carburetor and induction system icing. Inspect, check, service, and repair heat exchangers and superchargers.-Level 2:

The effect of using heated air during

periods of high engine power output. The pressures present in various portions of the induction system of supercharged

and unsupercharged reciprocating engines. The principles of operation and control of tul"bosuperchargers. The principles of operation and control

of integral superchargers.

The purpose and operation of the induction system impeller used in some radial

engmes.

Inspect, cheek, service, and repair carburetor air intake and induction manifolds.­ Level 3:

The position of the carburetOr heat control during engine starting.

39

The purpose and location of the induction system screen in a reciprocating

engine. The purpose and location of the "hot spot" heater in the induction system of some reciprocating engines.

The installation and operation of a multipoint priming system on a radial engine.

The purpose, location, and servicing re­

quirements for carburetor air filters.

The purpose and operation of ram air intake ducts on reciprocating engines.

L ENGINE COOLING SYSTEMS.

Repair engine cooling system components.-Level 2:

The attachment of cylinder head baffies.

The material used in the construction of

air baffies. Reprofile cylinder fins.

The effect of valve adjustment on the heat rejection rate of an engine.

Inspect, check, troubleshoot, service, and repair engine cooling systems.-Level 3 :

The operating principles of the cooling

system of vertically installed air-cooled 'helicopter engines.

The effects of excessive heat in an aircraft engine.

The purpose of fins on engine cylinders.

The effect of incorrectly installed 'baffies on engine operation.

The function and operation of cowl flaps.

The effect of fuel-air ratio on engine cooling. The purpose and operation of cooling air

augmenting systems.

The principles of "pressure ba.ffiing" used

in cooling aircra.ft engines.

The precautions necessary during ground operation of aircraft engines.

J. ENGINE EXHAUST SYSTEMS.

Repair engine exhaust system compo· nents.-Level 2:

The construction characteristics of ex­

haust augmenter tubes.

The materials used in exhaust system

components. The technique for cleaning ceramic-coated exhaust pipes.

Detect and repair cracks in stainless steel exhaust pipes.

The methods used to compensate for the

unequal expansion rate of exhaust system components.

Inspect, check, troubleshoot, service, and repair engine exhaust systems.-Level 3:

Inspect exhaust systems that utilize an

exhaust heat exchanger.

The purpose and operating principles of

the turbines driven by the exhaust gases of a tur!bo-compound engine.

The function and location of exhaust

augmenters.

The cause and effect of "frozen" ball

joints in an exhaust system.

Clean and test exhaust-type heating muffs.

The methods for torquing exhaust system clamps. The purpose and construction of exhaust gas noise suppressors. The effect of exhaust gas leakage on sys­ tem components.

The purpose and operation of engine thrust reversers.

K. PROPELLERS.

Inspect, check, service, and repair propeller synchronizing and ice control sys­

tems.-Level 1 :

The purpose of slinger rings on some

propeller installations.

The method of preventing ice formation on propeller spinners.

40

The operating principles of electrical de­

icing systems for propellers. The purpose of the governor step motor in the synchronizing system.

The purpose of propeller synchronizing

systems.

The operating principles of synchronizing systems. The operating principles of fluid anti­ icing systems.

Identify and select propeller lubricants. -Level2:

The principal requirements for propeller lubricants. The fa:ctors to be considered in selecting an oil or grease for a particular appli­ cation.

Balance propellers.-Level 2 :

The effects of propeller unbalance on en­ gine operation. Detect and correct vertical and horizontal unbalance in a two.Jblade propeller.

Balance a two-blade propeller that uses

a. separate hub for mounting on the engine crankshaft.

Repair propeller control system eompoonents.-Level 2:

Insta:ll oil control plugs in governors. Use manufacturer's data to repair com­

ponents. The purpose and operation of a propeller governor. The forces acting. on a governor to pro­

duce speed control. Determine the direction of rotation for

which a ·propeller governor is set.

Inspect, check, service, and repair fixedpitch, constant-speed, and feathering propellers, and propeller governing systems.­ Level 3:

The purpose and function of the parts of a propeller.

The aerodynamic forces· and loads acting on a rotating· propeller blade.

The operating principles of propeller controls used with turbine engines.

The meaning and significance of "static limits" as related to the installation of a fixed-pitch propeller. The purpose of the metal tipping on a. wood propeller.

Measure propeller blade angle. The meaning of propeller blade "back"

and "face." The method of making changes in the

speed and power output of an engine equipped with a constant-speed pro~er.

The operation of the distributor valve assembly of .a hydromatic propeller.

The normal position of a constant-speed

propeller control during takeoff.

The effect on engine operation of ~hang­

ing propeller pitch settings before a steady oil pressure is obtained after engine starting. The meaning and significance of "critical ranges" established for some engine-pro­

peller combinations. The operation of a propeller during the

feathering cycle. The operation of a propeller during the

reversing cycle.

The ,purpose of placing a propeller in a specified position ·prior to stopping the engine. The relationShip ·between blade position, airspeed, and angle of attack of the propeller blades. The operating principles of two-position and constant-speed counterweight .propellers. The method of lubricating the pitchchanging mechanism of a hydromatic propeller. The method of checking a steel propeller

hub or blade for cracks.

41

The general procedure to be followed when using the chemical etching process

to inspect aluminum alloy propeller blades.

Determine whether a bent a.luminum alloy propeller blade can be repaired by cold

straightening.

Clean and protect aluminum propeller blades.

The procedure for treating minor nicks

and scratches on aluminum propeller blades.

Determine the blade pitch stop settings

on a variable-pitch propeller.

The operating forces used to make blade pitch changes on various types of variablepitch propellers.

The location and purpose of propeller blade cuffs.

Install, troubleshoot, and remove propel­ Iers.-Level 3:

Perform an operational check of propeller

feathering system.

Detect and correct front and rear cone bottoming of a propeller installed on a

splined crankshaft.

The purpose and use of snap rings on propeller installations. The purpose and use of propeller cones in some propeller installations. Determine the amount of contact between a tapered crankshaft and the propeller hub. Install and track a fixed-pitch and con­

stant-speed propeller. Detect and correct looseness in a cable­

operated propeller control system. The most likely indications of a damaged piston-to-dome seal in a hydrom.a.tic pro­

peller. The most likely cause of oil leakage around the rear cone of a hydromatic propeller. Perform an operational check of a pro­

peller reversing system. The constant-speed propeller setting used when checking ignition systems. Adjust a propeller governor so that the ·propeller will operate within the correct range. The purpose and significance of preload­ ing the pitch -changing mechanism in a

hydromatic propeller.

42

ORAL AND PRACTICAL TESTS

Completion of the oral and practical tests is usually the final step in becoming certificated or in adding a rating to a mechanic certificate.

An oral and a practical test must be taken for each rating.

Oral and practical tests are administered by FAA Flight Standards inspectors or by FAA-designated mechanic examiners (DMEs). If an FAA inspector gives the tests, the required facility, tools, materials, and supplies must be furnished or arranged for by the

applicant. The adequacy and suitability of the facilities can be determined at the time

arrangements for the tests are being made.

If a DME gives the tests, he will furnish the facility and can usually arrange to furnish the tools, materials and supplies needed. DMEs

are not paid by the FAA for their services or the use of their facilities and equipment during the examination of mechanic applicants and are authorized to charge a fee for administering oral and practical tests. The names and

addresses of the FAA-designated mechanic examiners in each district can be obtained from the FAA Flight Standards district office that serves the area or from Advisory Circular No.

183--30, Directory of FAA Designated Mechanic Examiners.

The person administering the oral and practical tests will provide an application form

and give detailed instructions on how it should be filled out. He will explain each of the

projects to be assigned during the practical test and give some indication of the level of per­

formance expected.

The oral test may be administered along with the practical test in the form of questions about the projects being performed, or

it may be administered separately, before or after the practical test. The examiner will not attempt to trick or mislead you in any way

with his oral questions or project assignments.

Any assignment or question that you do not

understand should be clarified before continu­

ing with the test.

THE ORAL TEsT

Oral test questions cover the same subjects as the written tests and are intended to show how well the applicant can make use of his knowledge. Oral test questions fall generally

into three types: (a) questions closely related to assigned practical projects-to further ex­

plore the applicant's understanding of the tasks being performed, (b) questions not related to a specific project-to evaluate the applicant's ability in areas in which a skill

demonstration is not practical, and (c) questions to determine whether additional projects need t.o be assigned.

SAMPLE ORAL TEST QuESTIONS

Some examples of the type of questions asked during the oral test are :

1. How would you determine the leveling means for a specific aircraft ~ 2. What is a blind rivet and how is it used~ 3. What is reinforcing tape and how is it used? 4. What is the difference between welding and brazing~ 5. What is a circuit breaker and how does it work~

6. What are two causes of vapor lock in a fuel line~ 7. What is the purpose of a pump-unloading valve in a hydraulic system? 8. What cylinder should be removed last during disassembly of a radial aircraft

engine~ 9. What is detonation and how is it harmfuH 10. How would you check a magneto for correct internal timing ?

11. What is the purpose of an engine oildilution system~ 12. How would you check a propeller for correct track ~ 13. How is the moment of an item of equipment determined in computing aircraft

weight and balance~ 14. What precautions are required when fueling an aircraft ? 15. What are the procedures for correcting generator brush arcing? 16. What is the most common method for determining the state of charge of a leadacid battery ? 17. How would you determine the effect that the installation of a new item of equipment has on the balance of an aircraft~ 18. What is the purpose of a fuel tank sump and how is it inspected? 19. How would you determine the direction of rotation of a direct current motorj 20. Why is a reverse-current cutout relay required in a generator circuit? 21. What type compressor is most commonly used in aircraft turbine engines1 22. What are the installation practices for

th;~rmocouple leads? 23. What is the purpose and operation of the airfoil cooler in an engine lubrica­

tion system? 24. Explain the four-stroke, five-event cycle of a reciprocating engine. 25. What is the purpose of the turbine section in a jet engine? 26. What is an Airworthiness Directive? 27. What is the difference between a twoposition propeller and a constant-speed

propeller? 28. What are the general characteristics of the wood commonly used in aircraft construction? 29. How is stability about the horizontal axis of an aircraft obtained?

THE PRACTICAL TEST

The practical test consists of assigned work projects to test mechanical skill and ability to organize work, select and follow correct procedures, apply appropriate techniques, and ~etermine an acceptable level of workmansh1p.

The person administering the test will select projects that utilize as much as possible equipment and procedures that are familiar to the applicant.

A high level of manipulative skill in performing complex operations is not expected. Some of the basic skills must have been developed, however, and must be demonstrated

during the practical test.

A:pplicant's performance on projects in areas described as Level 3 in the section entitled "The Written Tests" will be expected to meet a return-to-service standard. If a project must be performed in accordance with a manufacturer's instruction or other data, the examiner will expect you to consult the instruction or data.

Any of the operations required to ~mplete the actions in Level 2 and Level 3 actiOn lines are potential practical projects. Notice, for instance, the entry under "E. Welding" of the Airframe Structures section of the listing. This entry is entitled "Solder, braze, gas- and arc-weld steel.-Level2." Since this is a Level 2 action line, the applicant may be asked to perform basic welding operations, but he will not be required to be a highly skilled welder to pass the practical test.

On the other hand, consider the entry under "E. Materials and Processes" of the General section of the listing. The action line, "In"

spect and check welds.-Level 3," indicates that the practical test may include a project that requires the applicant to inspect and make a dependable judgment about the quality of a welded joint. His judgment should be based upon (a) a generalized knowledge of weld­

ing materials, (b) a specific knowledge of the type of welded joint being inspected, and (c) the ability to .find out all the things he needs to know about the weld in order to judge its

quality.

SAMPLE PRAcTicAL TEsT PRoJEcTs

The following are typical of the projects assigned during mechanic practical tests.

1. Safety a turnbuckle. 2. Make a sheet metal splice. 3. Inspect a wood structure.

44

4. Remove, clean, inspect, and reinstall a brake master cylinder. 5. Gas-weld a steel tube. 6. Attach an electrical cable terminal. 1. Make up a section of fuel line and install fittings. 8. Bleed and adjust hydraulic brakes. 9. Compute empty weight center of gravity and the most forward and rearward loaded center of gravity of an aircraft. 10. Time the valves of an engine. 11. Adjust a carburetor float level. 12. Remove, clean, inspect, and reinstall an engine oil filter. 13. Install and time magnetos. 14. Remove and install a propeller. 15. Execute FAA Form 337, Major Repair and Alteration. 16. Perform a gear retraction test on an aircraft. 17. Replace shakeproof cowling fasteners. 18. Perform a fabric strength test. 19. Flash a direct current generator field. 20. Adjust turbine engine fuel controls. 21. Install packing seals and rings on hydraulic components. 22. Remove and install engine-driven hydraulic pumps. 23. Check an oxygen system for leaks. 24. Remove, clean, inspect, and install a fuel strainer. 25. Connect batteries to a constant-current battery charger. 26. Locate cracks in welded assemblies using dye penetrant. 27. Start an engine, and check for proper operation. 28. Adjust idle r.p.m. and mixture on a conventional carburetor.

29. Install engine cylinders and torque the holddown nuts. 30. Perform a cylinder compression test.

Oral and practical tests are graded as soon as they are completed, and the applicant is informed of his grade. If any part of either test is failed, the person administering the tests will issue a notice of disapproval of the application showing the titles of oral and practical subjects failed. He will also return the Airman Written Test Report that was presented by the applicant as evidence of having passed the written test.

An applicant who fails a test may apply for a retest as prescribed in FAR Part 65. An applicant has the option of returning to the same FAA office or DME or applying to

any other office or DME for the retest. The retest will include only the subjects failed.

When all parts of the tests have been passed, the FAA office or DME will issue a temporary

mechanic certificate. The following excerpts from FAR Part 65 pertain to temporary certificates.

"! 65.13 Temporary certificate.

A certificate and ratings effective for a period of not more than 90 days may be issued to a qualified applicant, pending review of his application and supplementary documents and the issue of the certificate and ratings for

which he applied."

Permanent certificates are prepared and issued by the Airman Certification Branch of

the Federal Aviation Administration and mailed to the address indicated by the applicant when he prepares the application form.

Figure

SAMPLE ~TTEN TEST QUESTIONS

The questions in this section are similar to those contained in FAA written tests for mechanics. They are included to show the type of questions used. No attempt has been made to cover any particular subjects.

1. What must a certificated mechanic with 1. increase in direct proportion to the both airframe and powerplant ratings do prior volume increase. to returning to service an aircraft on which he 2. remain the same. has performed and approved a 100-hour in­ 3. be doubled. spection' 4. be reduced to one-half its original 1. Make the proper entries in the approvalue. 4. How many AN470.AD--4-6 rivets will be priate logbooks.

required to attach a 10" x 5" splice plate if 2. Present his work and records to a single-row, minimum edge distance, 4D spacmechanic holding an Inspection Auing is used~ thorization for final approval and 1. 60 rivets. release. 2. 56 rivets. 3. Complete the required copies of FAA 3. 62 rivets. Form 337 including an accurate de­ 4. 52 rivets. scription of the work performed, date, mechanic's name, and certificate num­ ber. 4. Notify the local FAA maintenance in­ IT spector in writing of his intention to return the aircraft to service.

2. After making a major structural repair to an aircraft that is . to be returned to service, FAA Form 337, Major Repair and Alteration, must be prepared. How many copies are re­

quired and what is the final disposition of the completed forms¥

1. Three-one copy for the aircraft owner 5. The length of flat A in the above drawand two copies for the FAA. ing is 2. Tw()-()ne copy for the aircraft owner 1. 3.750 inches. and one copy for the FAA. 2. 3.875 inches. 3. Three--one copy for the aircraft owner, 3. 3.813 inches. one copy for the FAA, and one copy 4. 3.937 inches. for the permanent records of the repair­ 6. When making a forward weight and baling agency or individual. ance check to determine that the center of 4. Two-both copies for the FAA. gravity (e.g.) will not exceed the forward 3. If the container volume of a confined gas limit during extreme conditions, the items of is doubled (assume temperature remains conuseful load which should be computed at their stant), the pressure will minimum weights are those located aft of the Lenth of flatr A

47

1. forward e.g. limit 2. rearward e.g. limit. 3. datum. 4. empty weight e.g.

7. The micrometer scale shown above indicates a measurement of

1. 0.5195 inch. 2. 0.4945 inch. 3. 0.4695 inch. 4. 0.4819 inch. 8. As the velocity of the air across an aircraft wing increases, the pressure of the air on the upper surface

1. increases. 2. decreases. 3. drops to zero. 4. remains unchanged. 9. If the cross-sectional area of a given conductor is increased to four times its original value and the length and temperature remain constant, the resistance of the conductor will be

1. one-fourth its original value. 2. four-times its original value. 3. the same as ·its original value. 4. found by multiplying the original resistance by the percentage increase in cross-sectional area. 10. Which of the :following sequences of connecting and tightening the battery leads should result in the safest procedure for installation of a battery in an aircraft with a

single-wire, ground-return electrical system~

1. Connect and tighten the negative (ground) lead before connecting the positive lead. 2. Connect the negative (ground) lead, connect the positive lead, then tighten in the same order: 3. Connect the positive lead, connect the negative (ground) lead, then tighten in the same order.

4. Connect and tighten the positive lead before connecting the negative

(ground) lead.

11. Which of the following statements relating to the conduct of a 100-hour inspection is true?

1. The inspecting agency shall use an inspection form as a checklist while per­

forming a 100-hour inspection. 2. The inspecting agency is not required to use an inspection form as a checklist while performing a 100-hour inspec­

tion. 3. The inspecting agency shall use only the inspection form furnished and prescribed by the FAA Administrator as a checklist while performing a 100hour inspection. 4. The inspecting agency shall use only the inspection form furnished and pre­

scribed by the manufacturer as a checklist" while performing a 100-hour inspection. 12. Which of the following has little or no effect upon the rate of vaporization of a given

fuel~

1. The pressure of the surrounding air. 2. The temperature of th~ :fuel. 3. The temperature of the surrounding air. 4. The antiknock value of the :fueL

13. If an aircraft is cruising in level :flight and the stick or control column is moved forward, the elevator will

1. go down and the nose of the aircraft will go down. 2. go up and the nose of the aircraft will go down. 3. go down and the nose of the aircraft will go up. 4. go up and the nose of the aircraft will go up.

14. During the inspection of an aircraft equipped with a ·push-pull tube-type control system, the threaded rod ends should

1. be checked for the amount of thread engagement by means of the inspection hole provided.

48

2. be checked to determine that the ballbearing end is properly safetied to the push-pull rod with brass or stainless

steel safety wire. 3. be lubricated with waterproof highpressure grease. 4. not be adjusted in length for rigging purposes because the rod ends have been properly positioned and staked during manufacture 15. How should loosely adhering dust and .dirt be removed from the exterior surfaces of

aircraft transparent plastics~

1. Spray the surface with any commercial window cleaner. 2. Wipe the surface with a moist chamois. 3. Flush the surface with water. 4. Wipe the surface with a dry cloth. 16. When rigging the wings on a monoplane equipped with front and rear lift struts, the general practice is to

1. control dihedral angle by the length of the front struts. 2. establish the incidence angle by the length of the front struts, and wash-in and wash-out by adjusting the length of the rear struts. 3. pre-rig the rear struts and adjust the length of front struts for propeller­

to-rque correction as required. 4. use struts of fixed length and rig in propeller-torque correction by the use of ground-adjustable rudder tabs. 17. It is not considered good aircraft finishing technique to

Continue reading ↓ 120 of 162 passages shown