AC 65-15A [Large AC] Airframe and Powerplant Mechanics Airframe Handbook
Designed to familiarize student mechanics with airframe construction, repair, and the operating theory of airframe systems. SN 050-007-00391-9
This document is cancelled. It may have been replaced. Check the official source before relying on it.
Text read by OCR from a scanned file (4 of 612 pages). Check the original, as some words may be misread.
AC65-15A
Airfrarne 4 Powerplant
MECHANICS
AIRFRAME HANDBOOK
U.S. DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMIN~STRA TION
For sale by the U.S. Govemmcnt Prinling Office Superinrenclent of Documents, Mail Step: SSOP, WISIJin&ton, OC 20402-9328
ISBN 0-16-036209-1
PREFACE
This handbook was developed and first printed in 1972 as one of a series of three handbooks for persons preparing for certification as an airframe or powerplant mechanic. It i.s intended that this handbook will provide basic information on prin· ciples, fur.tlamentals and technical procedures in the subject matter areas relating to the airframe rating. It is designed to aid students enrolled in a formal course of instruction as well as the individual who is studying on his own. Since the knowledge requirements for the airframe and powerplant ratings closely parallel each other in some subject areas, the chapters which discuss fire protection systems and electrical systems contain some material which is also duplicated in the Airframe and Powerplant Mechanics Powerplant Handbook, AC 65-12A.
FEDERAL AVIATION ADMIN~STRA TION
This volume contains information on airframe construction features, assembly and rigging, fabric covering, structural repairs, and aircraft welding. The handbook also contains an explanation of the units which make up the various airframe systems.
Because there are so many different types of aircraft in use today, it is reasonable to expect that differences exist in airframe components and systems. To avoid undue repetition, the practice of using representative systems and units is carried out throughout the handbook. Subject matter treatment is from a generalized point of view, and should be supplemented by reference to manufacturers' p~anuals or other textbooks if more detail is desired. This handbook is not intended to replace, substitute for, or supersede official regulations or the manufacturers' instructions.
Grateful acknowledgement is extended to the manufacturers of engines, propellers, and powerplant accessories for their cooperation in making material avail-
able for inclusion in this handbook.
Copyright material is used by special permission of the following organizations and may not be extracted or reproduced without permission of the copyright owner.
Monsanto Chemicals Co. Townsend Corporation
J. 0. King, Inc. Gravines, Inc. Walter Kidde DuPont De Nemours National Fire Protection Association
National Association of Fire
Extinguisher Distributors Flight Safety Foundation
American Petroleum Institute Exxon Corporation Parker Hannifin Goodyear Tire and Rubber Co.
Firestone
iii
(R) Skydrol ® Fluids Cherry Rivets Acres Sleeves
Acres Sleeves Fire Extinguishers Fire Extinguishers Fire Extinguishants Fire Extinguisher and Extinguishant Specifications
Fire Extinguishers
Refueling Data Aviation Fuels Aviation Fuels Aircraft Fittings Aircraft Tires Aircraft Wheels Aircraft Brakes Aircraft Tires
Bendix Energy Controls
Rohm and Haas Douglas Aircraft Company
Aviation Maintenance Foundation, Inc. BF Goodrich
Puritan Equipment, Inc.
Aircraft Wheels Aircraft Brakes Plastics Portable Oxygen Generators in the DC-10 Air Conditioning Aircraft Tires Aircraft Wheels Aircraft Brakes Portable Oxygen Generators
The advancements in aeronautical technology dictate that an instructional hand· book must be under continuous review and brought up to date periodically to be valid. Flight Standards requested comments, from the certificated mechanic schools on the three handbooks. As a result, the handbooks have been updated to this extent: indicated errors have been corrected, new material has been added in the areas which were indicated as being deficient, and some material has bcc11 rearranged to improve the usefulness of the handbooks.
We would appreciate having errors brought to our attention, as well as receiving suggestions for improving the usefulness of the handbooks. Your comments and suggestions will be retained in our files until such time as the next revision will be
accomplished.
Address all correspondence relating to these handbooks to:
U.S. Department of Transportation Federal Aviation Administration Flight Standards National Field Office P.O. Box 25082 Oklahoma City, Oklahoma 73125
The companion handbooks to AC 65-15A are the Airframe and Powerplant Mechanics General Handbook, AC 65-9A and the Airframe and Powerplant Mechanics Powerplant Handbook, AC 65-12A.
iv
CONTENTS
PREFACE -------------------------------------------------------- iii
CO~E~S ------------------------------------------------------- v
CHAPTER 1. AIRCRAFT STRUCTURES
CHAPTER 1. AIRCRAFT STRUCTURES
General ------------------------------------------------------- 1 Major Structural Stresses ---------------------------------------- 1 Fixed-Wing Aircraft -------------------------------------------- 2
Fu~lage ------------------------------------------------------ 2 Wing Structure ------------------------------------------------ 6 Nacelles or Pods ----------------------------------------------- 13 ED1pennage ---------------------------------------------------- 16 Flight Control Surfaces ------------------------------------------ 18 Landing Gear -------------------------------------------------- 23 Skin and Fairing ----------------------------------------------- 24 Access and Inspection Doors ------------~------------------------- 24 Helicopter Structures -------------------------------------------- 24
CHAPTER 2. ASSEMBLY AND RIGGING
CHAPTER 2. ASSEMBLY AND RIGGING
General ------------------------------------------------------- 27 Theory of Flight ----------------------------------------------- 27 AerodynaJilics -------------------------------------------------- 27 The AtDlosphere ------------------------------------------------ 27
Pre~ure ------------------------------------------------------ 27 Den&ty ------------------------------------------------------- 28 HuDlidity ----------------------------------------------------- 28 Bernoulli's Principle and Subsonic Flow ---------------------------- 29 Motion ------------------------------------------------------- 29 Airfoils ------------------------------------------------------- 30 Center of Gravity ----------------------------------------------- 33 Thrust and Drag ----------------------------------------------- 33 Axes of an Aircraft --------------------------------------------- 35 Stability and Control -------------------------------------------- 35 Control ------------------------------------------------------- 39 Flight Control Surfaces ------------------------------------------ 40 Control Around the Longitudinal Axis ----------------------------- 41 Control Around the Vertical Axis --------------------------------- 44 Control Around the Lateral Axis ---------------------------------- 44 Tabs --------------------------------------------------------- 45
Boundary Layer Control Devices ---------------------------------- 48 Forces Acting on a Helicopter ------------------------------------ 49 Helicopter Axes of Flight ---------------------------------------- 55 High-Speed AerodynaDlics --------------------------------------- 56 Typical Supersonic. Flow Patterns --------------------------------- 59 AerodynaDlic Heating ------------------------------------------- 64 Flight Control SysteDls ------------------------------------------ 64 Hydraulic Operated Control SysteJils ------------------------------ 65 Cable Guides -------------------------------------------------- 66 Mechanical Linkage -------------------------------------------- 68
v
CHAPTER 2. ASSEMBLY AND RIGGING-(Cont.)
CHAPTER 2. ASSEMBLY AND RIGGING-(Cont.)
Torque Tubes -------------------------------------------------- 68 Stops --------------------------------------------------------- 68 Control Surface Snubbers and Locking Devices ---------------------- 69 Aircraft Rigging ----------------------------------------------- 70 Rigging Checks ------------------------------------------------ 72 Adjustment of Control Surfaces ----------------------------------- 75 Helicopter Rigging --------------------------------------------- 77 Principles of Balancing or Re-balancing ---------------------------- 80 Re-balancing Procedures ---------------------------------------- 83 Methods------------------------------------------------------- 83
CHAPI'ER 3. AIRCRAFT FABRIC COVERING
CHAPI'ER 3. AIRCRAFT FABRIC COVERING
Aircraft Fabrics ------------------------------------------------ 85 Miscellaneous Textile Materials ----------------------------------- 88 Seams -------------------------------------------------------- 89 Applying Covering --------------------------------------------- 91 Covering 1Vings ------------------------------------------------ 93 Covering Fuselages --------------------------------------------- 95 Ventilation, Drain, and Inspection Openings ------------------------ 95 Repair of Fabric Covers ----------------------------------------- 99 Replacing Panels in 1Ving Covers ---~----------------------------- 103 Re-covering Aircraft Surface with Glass Ooth ----------------------- 104 Causes of Fabric Deterioration ----------------------------------- 104 Checking Condition of Doped Fabric ------------------------------ 106 Testing Fabric Covering ----------------------------------------- 106 Strength Criteria for Aircraft Fabric ------------------------------ 107 Dopes and Doping---------------------------------------------- 107 Dope Materials ------------------------------------------------- 108 Aluminum-Pigmented Dopes ------------------------------------- 109 Temperature and Humidity Effects on Dope ------------------------ 109 Common Troubles in Dope Application ----------------------------- 109 Technique of Application ---------------------------------------- 110 Number of Coats Required --------------------------------------- 111
CHAPTER 4. AIRCRAFT PAINTING AND FINISHING
CHAPTER 4. AIRCRAFT PAINTING AND FINISHING
General ------------------------------------------------------- 113 Finishing Materials --------------------------------------------- 113 Paint Touchup ------------------------------------------------- 117 Identification of Paint Finishes ----------------------------------- 117 Paint Removal ---------~------------------------~-------------- 117 Restoration of Paint Finishes ------------------------------------- 118 Nitrocellulose Lacquer Finishes ----------------------------------- 118 Acrylic Nitrocellulose Lacquer Finish ------------------------------ 119 Epoxy Finishes ------------------------------------------------ 120 Fluorescent Finishes -------------------------------------------- 121 Enamcl Finishes ------------------------------------------------ 121 Paint System Compatibility -------------------------------------- 122 Methods of Applying Finishes ------------------------------------ 122 Preparation of Paint -------------------------------------------- 123
vi
CHAPTER 4. AIRCRAFT PAINTING AND FINISHING-(Cont.)
CHAPTER 4. AIRCRAFT PAINTING AND FINISHING-(Cont.)
Common Paint Troubles ----------------------------------------- 124 Painting Trim and Identification Numbers ------------------------- 125 Decalcomanias (Decals) ----------------------------------------- 125
CHAPTER 5. AIRCRAFT STRUCTURAL REPAIRS
CHAPTER 5. AIRCRAFT STRUCTURAL REPAIRS
Basic Principles of Sheet Metal Repair ---------------------------·:.: 127 General Structural Repair --------------------------------------- 129 Inspection of Damage ------------------------------------------- 130 Oassification of Damage ---------------------------------------- 131 Stresses in Structural Members ----------------------------------- 131 Special Tools and Devices for Sheet Metal -------------------------- 133 Metalworking Machines ----------------------------------------- 136 Forming Machines ---------------------------------------------- 141 Forming Operations and Terms ----------------------------------- 145 Making Straight Line Bends ------------------------------------- 146 Setback ------------------------------------------------------- 148 Making Layouts ------------------··----------------------------- 151 Hand Forming ------------------------------------------------- 155 Rivet Layout -------------------------------------------------- 164 Rivet Installation ----------------------------------------------- 166 Preparation of Rivet Holes --------------------------------------- 168 Driving Rive~ ------------------------------------------------- 173 Rivet Failures ------------------------------------------------- 175 Removing Rive~ ----------------------------------------------- 177 Special Rive~ -------------------------------------------------- 177 Self-Plugging (Friction Lock) Rivets ------------------------------ 178 Self-Plugging (Mechanical Lock) Rivets --------------------------- 181 Pull-Thru Rivets ----------------------------------------------- 184
Rivnu~ ------------------------------------------------------- 184 Dill Lok-Skrus and Lok-Rive~ ------------------------------------ 186 Deutsch Rivets ------------------------------------------------- 187 Hi-Shear Rivets ------------------------------------------------ 187 Specific Repair Types ------------------------------------------- 189 Structural Sealing ---------------------------------------------- 198 Metal Bonded Honeycomb --------------------------------------- 200 Construction Features ------------------------------------------- 201 Damage ------------------------------------------------------- 201 Repairs ------------------------------------------------------- 202 Repair Materials ----------------------------------------------- 205 Potted Compound Repair ---------------------------------------- 206 Glass Fabric Cloth Overlay Repairs ------------------------------- 208 One Skin .and Core Repair Procedures ----------------------------- 209 Plastics ------------------------------------------------------- 213 Transparent Plastics
-------------------------------------------- 213 Storage and Protection ------------------------------------------ 214 Forming Plastics ----------------------------------------------- 215 Installation Procedures ------------------------------------------ 220 Laminated Plastics ---------------------------------------------- 221 Fiber Glass Componen~ ----------------------------------------- 221 Radomes ------------------------------------------------------ 223 Wooden Aircraft Structures -------------------------------------- 224 Inspection of Wooden Structures ---------------------------------- 224 Service and Repair of Wooden Structures -------------------------- 228 Glues --------------------------------------------------------- 230 Gluing -------------------------------------------------------- 232
vii
CHAPTER 5. AIRCRAFT STRUCTURAL REPAIRS-(Cont.)
CHAPTER 5. AIRCRAFT STRUCTURAL REPAIRS-(Cont.)
Spliced Joints -------------------------------------------------- 234 Plywood Skin Repairs -------- ·---------------------------------- 235 Spar and Rib Repair ------------------------------------------- 242 Bolt and Bushing Holes ----------------------------------------- 244 Rib Repairs --------------------------------------------------- 245
CHAPTER 6. AIRCRAFT WELDING
CHAPTER 6. AIRCRAFT WELDING
General ------------------------------------------------------- 247 Oxyacetylene Welding Equipment --------------------------------- 248 Welding Positions ---------------------------------------------- 255 Welded Joints -------------------------------------------------- 255 Expansion and Contraction of Metals ------------------------------ 257 Correct Forming of a Weld -------------------------------------- 258 Oxyacetylene Welding of Ferrous Metals --------------------------- 258 Welding Nonferrous Metals Using Oxyacetylene --------------------- 260 Titanium ------------------------------------------------------ 262 Cutting Metal Using Oxyacetylene -------------------------------- 263 Brazing Methods ----------------------------------------------- 264 Soft Soldering ------------------------------------------------- 265 Electric Arc Welding ------------------------------------------- 266 Welding Procedures and Techniques ------------------------------- 269 Welding of Aircraft Steel Structures ------------------------------ 276
CHAPTER 7. ICE AND RAIN PROTECTION
CHAPTER 7. ICE AND RAIN PROTECTION
General ------------------------------------------------------- 285 Pneumatic Deicing Systems -------------------------------------- 286 Deicer Boot Construction ---------------------------------------- 287 Deicing System Components -------------------------------------- 288 Pneumatic Deicing System Maintenance --------------------------- 291 Thermal Anti-Icing Systems -------------------------------------- 293 Pneumatic System Ducting -------------------------------------- 296 Ground Deicing of Aircraft -------------------------------------- 299 Windshield Icing Control Systems --------------------------------- 300 Water and Toilet Drain Heaters ---------------------------------- 303 Rain Eliminating Systems --------------------------------------- 303 Maintenance of Rain Eliminating Systems -------------------------- 308
CHAPTER 8. HYDRAULIC AND PNEUMATIC POWER SYSTEMS
CHAPTER 8. HYDRAULIC AND PNEUMATIC POWER SYSTEMS
Aircraft Hydraulic Systems -------------------------------------- 309 Hydraulic Fluid ------------------------------------------------ 309 Types of Hydraulic Fluids --------------------------------------- 310 Phosphate Ester Base F1uids ------------------------------------- 311 Filters -------------------------------------------------------- 313 Basic Hydraulic System ----------------------------------------- 315 Reservoirs ----------------------------------------------------- .316 Pressure Regulation -------------------------------------------- 323 Actuating Cylinders -------------------------------------------- 328 Selector Valves ------------------------------------------------ 329 Aircraft Pneumatic Systems -------------------------------------- 331 Pneumatic System Components ----------------------------------- 334 Typical Pneumatic Power System --------------------------------- 338
CHAPTER 9. LANDING GEAR SYSTEMS
CHAPTER 9. LANDING GEAR SYSTEMS
General ------------------------------------------------------- 341 Main Landing Gear Alignment, Support, Retraction ------------------ 348
viii
CHAPTER 9. LANDING GEAR SYSTEMS-(Cont.)
Emergency Extension Systems ------------------------------------ 351 Landing Gear Safety Devices ------------------------------------- 351 Nosewheel Steering System -------------------------------------- 354 Shimmy Dampers ---------------------------------------------- 356 Brake Systems ------------------------------------------------- 360 Brake Assemblies ----------------------------------------------~ 366 Inspection and Maintenance of Brake Systems ---------------------- 372 Aircraft Landing Wheels ---------------------------------------- 373 Aircraft Tires -------------------------------------------------- 377 Aircraft Tire Maintenance --------------------------------------- 379 Tire Inspection-Mounted On Wheel ------------------------------ 381 Tire Inspection-Tire Demounted --------------------------------- 382 Tube Inspection ------------------------------------------------ 384 Mounting and Demounting -------------------------------------- 385 Causes of Air Pressure Loss in Tubeless Aircraft Tires ---------------- 389 The Wheel ---------------------------------------------------- 390 Good Pressure Gage Practice ------------------------------------- 391 Repairing ----------------------------------------------------- 392 Operating and Handling Tips ------------------------------------ 394 Tube Repair --------------------------------------------------- 396 Sidewall.Jnflated Aircraft Tires ----------------------------------- 396 Tire Inspection Summary ---------------------------------------- 397 Antiskid System ------------------------------------------------ 399 Landing Gear System Maintenance -------------------------------- 400
CHAPTER 10. FIRE PROTECTION SYSTEMS
CHAPTER 10. FIRE PROTECTION SYSTEMS
General ------------------------------------------------------- 407 Fire Detection Systems ------------------------------------------ 408 Types of Fires ------------------------------------------------- 411 Fire Zone Classification ----------------------------------------- 412 Extinguishing Agent Characteristics ------------------------------- 412 Fire Extinguishing Systems -------------------------------------- 417 Reciprocating Engine Conventional C02 System --------------------- 417 Turbojet Fire Protection System ---------------------------------- 419 Turbine Engine Fire Extinguishing System ------------------------- 420 Turbine Engine Ground Fire Protection ---------------------------- 422 Fire Detection System Maintenance Practices ----------------------- 423 Fire Detection System Troubleshooting ---------------------------- 425 Fire Extinguisher System Maintenance Practices -------------------- 425 Fire Prevention and Protection ----------------------------------- 429 Cockpit and Cabin Interiors -------------------------------------- 429 Smoke Detection Systems ---------------------------------------- 430
CHAPTER 11. AIRCRAFT ELECTRICAL SYSTEMS
CHAPTER 11. AIRCRAFT ELECTRICAL SYSTEMS
General ------------------------------------------------------- 433 Lacing and Tying Wire Bundles ---------------------------------- 444 Cutting Wire and Cable ---------------------------------------- 446 Emergency Splicing Repairs ------------------------------------- 450 Connecting Terminal Lugs to Terminal Blocks ----------------------- 451 Bonding and Grounding ---------------------------------------- 452 Connectors ---------------------------------------------------- 452 Conduit ------------------------------------------------------- 457 Electrical Equipment Installation --------------------------------- 457 Aircraft Lighting Systems --------------------------------------- 459 Maintenance and Inspection o£ Lighting Systems -------------------- 464
lX
CHAPTER 12. AIRCRAFT INSTRUMENT SYSTEMS
CHAPTER 12. AIRCRAFT INSTRUMENT SYSTEMS
Gener& ----------------------------------------------~-------- 469 ln~rument c~s ---------------------------------------------- 469 Di&s --------------------------------------------------------- 469 Range Markings ----------------------------------------------- 470 Instrument Pands ---------------------------------------------- 470 Repair of Aircrah ln~ruments ----------------------------------- 471 Aircraft Pressure Gages --------------------------------------- _ 471 Pitot-Static System --------------------------------------------- 474 Maintenance of Pitot-Static Systems ------------------------------- 481 Tum-and-Bank lndlcator ---------------------------------------- 482 Synchro-Type Remote Indicating Instruments ----------------------- 483 Remote-Indicating Fud and Oil Pressure Gages --------------------- 485 Capacitor-Type Fuel Quanity System ------------------------------ 485 Angle-of-Attack Indicator ---------------------------------------- 487 Tachometers --------------------------------------------------- 488 Synchroscope --------------------------------------------------
491 Temperature Indicators ----------------------------------------- 491 Ratiometer Electric& Resistance Thermometer ---------------------- 497 Fuel Flowmeter Systems ----------------------------------------- 497 Gyroscopic Instruments ----------------------------------------- 499 Sources of Power for Gyro Operation ------------------------------ 501 Vacuum-Driven Attitude Gyros ----------------------------------- 504 Pressure-Operated Gyros ---------------------------------------- 506 Vacuum System Maintenance Practices ---------------------------- 506 Electric Attitude Indicator --------------------------------------- 507 Autopilot System ----------------------------------------------- 511 Basic Autopilot Components -------------------------------------- 513 Flight Director Systems ----------------------------------------- 518 Autopilot System Maintenance ------------------------------------ 516
CHAPTER 13. COMMUNICATIONS AND NAVIGATION SYSTEMS
CHAPTER 13. COMMUNICATIONS AND NAVIGATION SYSTEMS
Gener& ------------------------------------------------------- 519 Basic Radio Principles ------------------------------------------ 519 Basic Equipment Components ------------------------------------ 520 Power Supply ------------------------------------------------- 522 Communication Systems ----------------------------------------- 522 Airborne Navigation Equipment ---------------------------------- 524 VHF Omnirange Sy~em ---------------------------------------- 524 Instrument Landing System -------------------------------------- 525 Distance-Measuring Equipment ----------------------------------- 528 Automatic Direction Finders ------------------------------------- 529 Radar Beacon Transponder -------------------------------------- 530 Doppler Navigation Systems ------------------------------------- 530 Inertial Navigation System -------------------------------------- 531 Airborne Weather Radar System --------------------------------- 532 Radio Altimeter ------------------------------------------------ 533 Emergency Locator Transmitter (ELT) ---------------------------- 533 Installation of Communication and Navigation Equipment ------------- 534 Reducing Radio Interference ------------------------------------ 536
ln~&latoin of Aircraft Antenna Systems --------------------------- 537
CHAPTER 14. CABIN ATMOSPHERE CONTROL SYSTEM
Need for Oxygen ---------------------------------------------- 539 Com~tion of the Atmosphere ---------------------------------- 539
Pressur~ation -------------------------------------------------- 541 Air Conditioning and Pressurization Systems ----------------------- 543
CHAPTER 14. CABIN ATMOSPHERE CONTROL SYSTEM
X
CHAPTER 14. CABIN ATMOSPHERE CONTROL SYSTEM-(Cont.)
Basic Requirements -------------------------------------------- 545 Sources of Cabin Pre~ure --------------------------------------- 545 Supercharger Instruments --------------------------------------- 549
Pre~urization Valves ------------------------------------------- 550 Cabin Pr~ure Control System ----------------------------------, . .,.
CHAPTER 14. CABIN ATMOSPHERE CONTROL SYSTEM-(Cont.)
551 Air Distribution ----------------------------------------------- 556 Air Conditioning System ---------------------------------------- 558 Heating Systems ----------------------------------------------- 559 Combustion Heaters -------------------------------------------- 561 Maintenance of Combustion Heater Systems ------------------------ 564 Cooling Systems ------------------------------------------------ 565 Air Cycle Cooling System --------------------------------------- 565 Air Cycle System Component Operation --------------------------- 568 Electronic Cabin Temperature Control System ---------------------- 574 Electronic Temperature Control Regulator ------------------------- 575 Vapor Cycle System (Freon) ------------------------------------ 576 Freon System Components --------------------------------------- 577 Description of a Typical System --------------------------------- 580 Air Conditioning and Pr~urization System Maintenance ------------- 583 Cabin Pre~urization Operational Checks --------------------------- 585 Cabin Pr~urization Troubleshooting
----------------------------- 586 Oxygen Systems General ----------------------------------------- 587 Portable Oxygen Equipment ------------------------------------- 587 Smoke Protection Equipment ------------------------------------- 588 Oxygen Cylinders ---------------------------------------------- 588 Solid State Oxygen Systems ------------------------------------- 589 Oxygen Plumbing ---------------------------------------------- 591 Oxygen Valves ------------------------------------------------ 592 Regulators ----------------------------------------------------- 594 Oxygen System Flow Indicators ----------------------------------- 597 Pressure Gages ------------------------------------------------ 597 Oygen Masks -------------------------------------------------- 597 Servicing Gaseous Oxygen Systems ------------------------------- 598 Prevention of Oxygen Fires or Explosions ------------------------- 600
xi
GENERAL
The airframe of a fixed-wing aircraft is generally considered to consist of five principal units, the fuselage, wings, stabilizers, flight control surfaces, and landing gear. Helicopter airframes consist of the fuselage, main rotor and related gearbox, tail
rotor (on helicopters with a single main rotor), and the landing gear.
The airframe components are constructed from a wide variety of materials and are joined by rivets, bolts, screws, and welding or adhesives. The air· craft components are composed of various parts called structural members (i.e., stringers, longerons, ribs, bulkheads, etc.). Aircraft structural members are designed to carry a load or to resist stress. A single member of the structure may be subjected to a combination of stresses. In most cases the structural members are designed to carry end loads rather than side loads: that is, to be subjected to tension or compression rather than bending.
Strength may be the principal requirement in cer· tain structures, while others need entirely different qualities. For example, cowling, fairing, and simi· lar parts usually are not required to carry the stresses imposed by flight or the landing loads. However, these parts must have such properties as neat appearance and streamlined shapes.
MAJOR STRUCTURAL STRESSES
MAJOR STRUCTURAL STRESSES
In designing an aircraft, every square inch of wing and fuselage, every rib, spar, and even each metal fitting must be considered in relation to the physical characteristics of the metal of which it is made. Every part of the aircraft must be planned to carry the load to be imposed upon it. The determi· nation of such loads is called stress analysis. AI· though planning the design is not the function of the aviation mechanic, it is, nevertheless, important that he understand and appreciate the stresses involved in order to avoid changes in the original design through improper repairs.
There are five major stresses to which all aircraft are subjected (figure 1-1):
1
(1) Tension. (2) Compression. (3) Torsion. (4) Shear. (5) Bending.
CHAPTER 1
CHAPTER 1
AIRCRAFT STRUCTURES
The term "stress" is often used interchangeably with the word "strain." Stress is an internal force of a substance which opposes or resists deforma· tion. Strain is the deformation of a material or substance. Stress, the internal force, can cause strain.
AIRCRAFT STRUCTURES
Tension (figure 1-1a) is the stress that resists a force that tends to pull apart. The engine pulls the aircraft forward, but air resistance tries to hold it back. The result is tension, which tries to stretch the aircraft. The tensile strength of a material is measured in p.s.i. (pounds per square inch) and is calculated by dividing the load (in pounds) required to pull the material apart by its cross-sectional area (in square inches).
Compression (figure 1-1b) is the stress that resists a crushing force. The compressive strength of a material is also measured in p.s.i. Compression is the stress that tends to shorten or squeeze aircraft parts.
Torsion is the stress that produces twisting (figure 1-1c). While moving the aircraft forward, the en· gine also tends to twist it to one side, but other aircraft components hold it on course. Thus, torsion is created. The torsional strength of a material is ita resistance to twisting or torque.
Shear is the stress that resists the force tending to cause one layer of a material to slide over an adjacent layer. Two riveted plates in tension (figure 1-1d) subject the rivets to a shearing force. Usually, the shearing strength of a material is either equal to or less than its tensile or compressive strength. Aircraft parts, especially screws, bolts, and rivets, are often subject to a shearing force.
Bending stress is a combination of compression and tension. The rod in figure 1-1e has been short· ened (compressed) on the inside of the bend and stretched on the outside of the bend.
(a) Tension
(b) Compression
(c) Torsional (d) Shear
Tension outside of bend
L
(e) Beadmg (the combfll&tion stress)
FIGURE 1-1. Five stresses acting on an aircraft.
FIXED-WING AIRCRAFT
FIXED-WING AIRCRAFT
The principal components of a single-engine, propeller-driven aircraft are shown in figure 1-2.
Figure 1-3 illustrates the structural components of a typical turbine powered aircraft. One wing and the empennage assemblies are shown exploded into the many components which, when assembled, form major structural units.
FUSELAGE
The fuselage is the main structure or body of the aircraft. It provides space for cargo, controls, accessories, passengers, and other equipment. In singleengine aircraft, it also houses the powerplant. In
2
multi-engine aircraft the engin~ may either be in the fuselage, attached to the fuselage, or suspended from the wing structure. They vary principally in Jize and arrangement of the different compartments.
There are two general types of fuselage construction, the truss type, and the monocoque type. A truss is a rigid framework made up of members such as beams, struts, and bars to resist deformation by applied loads. The truss-framed fu.CJelage is generally covered with fabric.
Truss Type
The truss type fuselage frame (figure 1-4) is usually constructed of steel tubing welded together in such a manner that all members of the truss can carry both tension and compression loads. In some
.__--Propeller
aircraft, principally the light, single-engine models, truss fuselage frames are col18tructed of aluminum alloy and may be riveted or bolted into one piece, with cross-bracing achieved by using solid rods or tubes.
Monocoque Type
The monocoque (single shell) fuselage relies largely on the strength of the skin or covering to carry the primary stresses. The design may be divided into three classes: (1) Monocoque, (2) semi· monocoque, or (3) reinforced shell. The true monocoque construction (figure 1-5) uses formers, frame assemblies, and bulkheads to give shape to the fuselage, but the skin carries the primary stresses. Since no bracing members are present, the skin must be strong enough to keep the fuselage rigid. Thus, the biggest problem involved in monocoque col18truction is maintaining enough strength while keeping the weight within allowable limits.
To overcome the strength/weight problem of monocoque construction, a modification called semimonocoque construction (figure 1-6) was developed.
3
Vertical stabilizer
In addition to formers, frame assemblies, and bulkheads, the semimonocoque construction has the skin reinforced by longitudinal membel8. The reinforced shell has the skin reinforced by a complete framework of structural members. Different portions of the same fuselage may belong to any one of the three classes, but most aircraft are considered to be of semimonocoque type col18truction.
Semimonocoque Type
The semimonocoque fuselage is constructed pri· marily of the alloys of aluminum and magnesium, although steel and titanium are found in areas of high temperatures. Primary bending loads are taken by the longerons, which usually extend across sev· eral points of support. The longerons are supplemented by other longitudinal members, called
stringers. Stringers are more numerous and lighter in weight than longerons. The vertical structural members are referred to as bulkheads, frt1111a, tJ7Ul
formers. The heaviest of these vertical members are located at intervals to carry concentrated loads and at points where fittings are used to attach other units, such as the wings, powerplants, and stabiliz·
Vertical stabilizer Rudder
Fuselage section
Inboard aileron
Main landing
gear g, ?:!.
Pylon wmg leadmg f.mg ...-
'Li
Wing tip
Wing center section or. strut edge Powerplant
F!Guu 1-S. Typical atructural components of a turbine powered aircraft.
Longeron (tubular steel)
Fic'llllB 1-4. Warren tru11 of welded tubular steeL
ers. Figure 1-7 shows one form of the semimonocoque design now in use.
The stringers are smaller and lighter than Ionge-
4
rons and serve as fill-ins. They have some rigidity, but are chiefly used for giving shape and for attachment of the skin. The strong, heavy longerons hold the bulkheads and formers, and these, in tum, hold the stringers. All of these joined together form a rigid fuselage framework.
There is often little di1Jerence between some rings, frames, and formers. One manufacturer may call a brace a former, whereas another may call the same type of brace a ring or frame. Manufacturers' instructions and specifications for a specific aircraft are the best guides.
Stringers and longerons prevent tension and compression from bending the fuselage. Stringers are usually of a one-piece aluminum alloy cottstruction, and are manufactured in a variety of shapes by casting, extrusion, or forming. Longerons, like stringers, are usually made of aluminum alloy; how-
Bullchead
Flc'IJU 1-5. Mollocoque CODStniCticm.
ever, they may be of either a one-piece or a built-up construction.
By themselves, the structural members discussed do not give strength to a fuselage. They must first be joined together by such coDDeCtive devices as gussets, rivets, nuts and bolts, or metal screws. A gusset (figure 1-7) is a type of connecting bracket. The bracing between longerons is often referred to as web members. They may be installed vertically or diagonally.
The metal skin or covering is riveted to the longerons, bulkheads, and other structural members and carries part of the load. The fuselage skin thickness will vary with the load carried and the stresses sustained at a particular location.
There are a number of advantages in the use of the semimonocoque · fuselage. The bulkheads, frames, stringers, and longerons facilitate the design and construction of a streamlined fuselage, and add to the strength and rigidity of the structure. The main advantage, however, lies in the fact that it
5
Flc1JU 1-7. Fuselap stnactaral memhen.
does not depend on a few members for strength and rigidity. This means that a semimonocoque :ftwelap, because of its stressed-skin construction, may with· stand conaiderable damage and still be strons enough to hold together.
Fuselages are generally constructed in two or more sections. On small aircraft, they are generaBy made in two or three sections, while larger aircraft may be made up of as many as six sections.
Quick access to the accessories and other equipment carried in the fuselage is provided for by numerous access doors, inspection plates, landiq wheel wells, and other openings. Servicing diagrama showing the arrangement of equipment and location of access doors are supplied by the manufacturer in the aircraft maintenance manual.
Location Numberiq Systems
There are various numbering systems in use to facilitate location of specific wing frames, fuselap bulkheads, or any other structural members on an aircraft. Most manufacturers U8e some system of station marking; for example, the noee of the aircraft may be designated zero station, and aD other stations are located at measured distances in incl. behind the zero station. Thus, when a blueprint reads "fuselage frame station 137," that particular frame station can be located 137 in. behind the noee of the aircraft. A typical station diagram is shown in figure 1-3.
To locate structures to the right or left of the center line of an aircraft, many manufacturen COD• aider the center line as a zero station for structural member location to its right or left. With BUCh a
r·t n
+-t . +-t -m ll "'--- t1
- ~-~ )...I )...I
"""' .··.ill~ , … … ,..,..
f-· 1'--:-' ~ II l
0 tttt LJ..V 1m . "rt ~H lj i iiiiiii
¢
I ¢ ~
!: 0 ;;; -:. ....
WL = Waterline
Fuselage stations
FIGURE 1-8. Fuselage stations.
system the stabilizer frames can he designated as being so many inches right or left of the aircraft center line.
The applicable manufacturer's numbering system and abbreviated designations or symbols should always he reviewed before attempting to locate a structural member. The following list includes location designations typical of those used by many manufacturers.
(1) Fuselage stations (Fus. Sta. or F.S.) are
numbered in inches from a reference or zero point known as the reference datum. The reference datum is an imaginary vertical plane at or near the nose of the aircraft from which all horizontal distances are measured. The distance to a given point is measured in inches parallel to a center line extending through the aircraft from the nose through the center of the tail cone. Some manufacturers may call the fuselage station a body station, abbreviated B.S.
(2) Buttock line or butt line (B.L.) is a
width measurement left or right of, and parallel to, the vertical center line. (3) Water line (W.L.) is the measurement of
height in inches perpendicular from a horizontal plane located a fixed number
of inches below the bottom of the aircraft fuselage. (4) Aileron station (A.S.) is measured out-
hoard from, and parallel to, the inboard
edge of the aileron, perpendicular to the rear beam of the wing. (5) Flap station (F.S.) is measured perpen-
6
dicular to the rear beam of the wing and parallel to, and outboard from, the in-
hoard edge of the flap. (6) Nacelle station (N.C. or Nac. Sta.) is
measured either forward of or behind the front spar of the wing and perpendic-
ular to a designated water line. In addition to the location stations listed above, other measurements are used, especially on large aircraft. Thus, there may he horizontal stabilizer stations (H.S.S.), vertical stabilizer stations (V.S.S.) or powerplant stations (P.P.S.). In every case the manufacturer's terminology and station location system should he consulted before locating a point on a particular aircraft.
WING STRUCTURE
WING STRUCTURE
The wings of an aircraft are surfaces which are designed to produce lift when moved rapidly through the air. The particular design for any given aircraft depends on a number of factors, such as size, weight, use of the aircraft, desired speed in flight and at landing, and desired rate of climb. The wings of a fixed-wing aircraft are designated left and right, corresponding to the left and right sides of the operator when seated in the cockpit.
The wings of some aircraft are of cantilever design; that is, they are built so that no external bracing is needed. The skin is part of the wing structure and carries part of the wing stresses. Other aircraft wings use external hracings (struts, wires, etc.) to assist in supporting the wing and carrying the aerodynamic and landing loads. Both aluminum alloy and magnesium alloy are used in wing construction. The internal structure is made up of spars and stringers running spanwise, and
ribs and formers running chordwise (leading edge to trailing edge). The spars are the principal struc· tural members of the wing. The skin is attached to the internal members and may carry part of the wing stresses. During flight, applied loads which are imposed on the wing structure are primarily on the skin. From the skin they are transmitted to the ribs and from the ribs to the spars. The spars support all distributed loads as well as concentrated weights, such as fuselage, landing gear, and, on multi-engine aircraft, the nacelles or pylons.
The wing, like the fuselage, may be constructed in sections. One commonly used type is made up of a center section with outer p811els and wing tips. Another arrangement may have wing stubs as an integral part of the fuselage in place of the center section.
Inspection openings and access doors are provided, usually on the lower surfaces of the wing. Drain holes are also placed in the lower surface to provide for drainage of accumulated moisture or fluids. On some aircraft built-in walkways are provided on the areas where it is safe to walk or step. On some aircraft jacking points are provided on the underside of each wing.
Various points on the wing are located by station number. Wing station 0 (zero) is located at the center line of the fuselage, and all wing stations are measured outboard from that point, in inches.
In general, wing construction is ba8ed on one of three fundamental designs: (1) :M~nospar, (2) multi-spar, or (3) box beam. Modifications of these basic designs may be adopted by various manufacturers.
The monospar wing incorporates only one main longitudinal member in its construction. Ribs or bulkheads supply the necessary contour or shape to the airfoil. Although the strict monospar wing is not common, this type of design, modified by the addition of false spars or light shear webs along the trailing edge as support for the control surfaces, is sometimes used.
The multi-spar wing incorporates more than one main longitudinal member in its construction. To give the wing contour, ribs or bulkheads are often included.
The box beam type of wing construction uses two main longitudinal members with connecting bulkheads to furnish additional strength and to give contour to the wing. A corrugated sheet may be
Tapered leading edge,
straight trailing edge
Tapered leading and trailing edges Delta wing
Swept back wings
Straight leading and
trailing edges
Flc:ou 1~. Typical wing leacliDg and trailiDs edge shapea.
7
Straight leading edge,
tapered trailing edge
placed between the bulkheads and the smooth outer skin so that the wing can better carry tension and compression loads. In some cases, heavy longitudinal stiffeners are substituted for the corrugated sheets. A combination of corrugated sheets on the upper surface of the wing and stiffeners on the lower surface is sometimes used.
Wing Configurations
Depending on the desired flight characteristics, wings are built in many shapes and sizes. Figure 1-9 shows a number of typical wing leading and trailing edge shapes.
In addition to the particular configuration of the leading and trailing edges, wings are also designed to provide certain desirable flight characteristics, such as greater lift, balance, or stability. Figure 1-10 shows some common wing forms. Features of the wing will cause other variations in its design. The wing tip may be square, rounded, or even pointed. Both the leading edge and the trailing edge of the wing may be straight or curved, or one edge may be straight and the other curved. In addition, one or both edges may be tapered so that the wing is narrower at the tip than at the root where it joins the fuselage. Many types of modern aircraft employ sweptback wings (figure 1-9) .
Wing Spars
The main structural parts of a wing are the spars, the ribs or bulkheads, and the stringers or stiffe· ners, as shown in figure 1-11.
Spars are the principal structural members of the wing. They correspond to the longerons of the fuselage. They run parallel to the lateral axis, or toward the tip of the wing, and are usually attached to the fuselage by wing fittings, plain beams, or a truss system.
a 0
Low wing Dihedral
0
High wing Mid wing
Gull wing Inverted gull
FIGURE 1-10. Common wing fol'lllll.
Wooden spars can be generally classified into four different types by their cross sectional configu· ration. As shown in figure 1-12, they may be partly hollow, in the shape of a box, solid or laminated, rectangular in shape, or in the form of an 1-beam.
Spars may be made of metal or wood depending on the design criteria of a specific aircraft. Most aircraft recently manufactured use spars of solid extruded aluminum or short aluminum extrusions
riveted together to form a spar.
The shape of most wooden spars is usually similar to one of the shapes shown in figure 1-12. The
rectangular form, figure 1-12A, can be either solid or laminated. Figure 1-12B is an 1-beam spar that has been externally routed on both sides to reduce weight while retaining adequate strength. A box spar, figure 1-12C, is built up from plywood and solid spruce. The 1-beam spar, figure 1-120, may be built up of wood or manufac-
FIGURE 1-11. Internal wing construction.
8
A B c D E
FIGURE 1-12. Typical spar cross sectional configurations.
tured by an aluminum extrusion process. The 1heam construction for a spar usually consists of a web (a deep wall plate) and cap strips, which are extrusions or formed angles. The web forms the principal depth portion of the spar. Cap strips are extrusions, formed angles, or milled sections to which the web is attached. These members carry the loads caused by the wing bending and also provide
a foundation for attaching the skin. An example of a hollow or internally routed spar is represented in figure 1-12E.
Figure 1-13 shows the basic configuration of some typical metal spars. Most metal spars are built up from extruded aluminum alloy sections, with riveted aluminum alloy web sections to provide extra strength.
FIGURE 1-13. Metal spar shapes.
Although the spar ahapes of figure 1-13 are typical of most basic shapes, the actual spar configuration may assume many forms. For example, a spar may have either a plate or truss type web. The plate web (figure 1-14) consists of a solid plate with vertical stiffeners which increase the strength of the web. Some spar plate webs are constructed differently. Some have no stiffeners; others contain flanged holes for reducing weight. Figure 1-15 shows a truss spar made up of an upper cap, a lower cap, and connecting vertical and diagonal tubes.
A structure may he designed so as to he considered "fail-safe." In other words, should one member of a complex structure fail, some other member would assume the load of the failed member.
9
A spar with "fail-safe" construction is shown in figure 1-16. This spar is made in two sections. The top section consists of a cap, riveted to the upper web plate. The lower section is a single extrusion, consisting of the lower cap and web plate. These two sections are spliced together to form the spar. If either section of this type of spar breaks, the other section can still carry the load, which is the "fail-safe" feature.
As a rule, a wing has two spars. One spar is usually located near the front of the wing, and the other about two-thirds of the distance toward the wing's trailing edge. Regardless of type, the spar is the most important part of the wing. When other structural members of the wing are placed under load, they pass most of the resulting stress on to the wing spars.
FIGURE 1-14. Plate web wing spar.
Upper cap member l Diagonal tube F=====· ======l~~r=~
Lower cap member
FIGURE 1-15. Truss wing spar.
FIGURE 1-16. Wing spar with "fail-safe" construction.
10
Wing Ribs
Ribs are the structural crosspieces that make up the framework of the wing. They usually extend from the wing leading edge to the rear spar or to the trailing edge of the wing. The ribs give the wing its cambered shape and transmit the load from the skin and stringers to the spars. Ribs are also used in ailerons, elevators, rudders, and stabilizers.
Ribs are manufactured from wood or metal. Either wood or metal ribs are used with wooden spars while metal ribs are usually used with metal spars. Some typical wooden ribs, usually manufactured from spruce, are shown in figure 1-17.
A
B
c
FIGURE 1-17. Typical wooden ribs.
The most common types of wooden ribs are the plywood web, the lightened plywood web, and the truss types. Of these three types, the truss type is the most efficient, but it lacks the simplicity of the other types.
The wing rib '"h.own in Figure 1-17A is a truss type, with plywood gussets on both sides of the rib and a continuous rib cap around the entire rib. Rib caps, often called cap strips, are usually made of the same material as the rib itself, especially when using wooden ribs. They stiffen and strengthen the rib and provide an attaching surface for the rib covering.
A lightened plywood web rib is illustrated in figure 1-17B. On this type the cap strip may be laminated, especially at the leading edge. Figure
l-17C shows a rib using a continuous gusset, which provides extra support throughout the entire rib with very little additional weight.
A continuous gusset stiffens cap strips in the plane of the rib. This aids in preventing buckling and helps to obtain better rib/skin glue joints where nail-gluing is used because such a rib can resist the driving force of nails better than the other types. Continuous gussets are more easily handled than the many small separate gussets otherwise required.
Figure 1-18 shows the basic rib and spar structure of a wooden wing frame, together with some of the other wing structural members. In addition to the front and rear spars, an aileron spar, or false spar, is shown in figure 1-18. This type of spar extends only part of the spanwise length of the wing and provides a hinge attachment point for the aileron.
Various typ~ of ribs are also illustrated in figure 1-18. In addition to the wing rib, sometimes called "plain rib" or even "main rib," nose ribs and the butt rib are shown. A nose rib is also called a false rib, since it usually extends from the wing leading edge to the front spar or slightly beyond. The nose ribs give the wing leading edge area the necessary curvature and support. The wing rib, or plain rib, extends from the leading edge of the wing to the rear spar and in some cases to the trailing edge of the wing. The wing butt rib is normally the heavily stressed rib section at the inboard end of the wing
Wing tip Nose rib or false rib
near the attachment point to the fuselage. Depending on its location and method of attachment, a butt rib may be called a bulkhead rib or a compression rib, if it is designed to receive compression loads that tend to force the wing spars ~ogether.
Since the ribs are laterally weak, they are strengthened in some wings by tapes that are woven above and below rib sections to prevent sidewise bending of the ribs.
Drag and antidrag wires (figure 1-18) are crisscrossed between the spars to form a truss to resist forces acting on the wing in the direction of the wing chord. These tension wires are also referred to as tie rods. The wire designed to resist the backward forces is called a drag wire; the antidrag wire resists the forward forces in the chord direction.
The wing attachment fittings, shown in figure 1-18, provide a means of attaching the wing to the aircraft fuselage.
The wing tip is often a removable unit, bolted to the outboard end of the wing panel. One reason for this is the vulnerability of the wing tips to damage, especially during ground handling and taxiing.
Figure 1-19 shows a removable wing tip for a large aircraft wing. The wing-tip assembly is of aluminum alloy construction. The wing-tip cap is secured to the tip with countersunk screws and is
Leading edge strip
Antidrag wire
or tie rod
Atl~n Atleron Rearspar hinge
FiGURE 1-18. Basic rib and spar structure.
Wing butt rib - (or compression rib)
(or bulkhead rib)
Wing attach·-.
fittings
secured to the intenpar structure at four points with lA,-in. bolts. The tip leading edge contains the heat anti-icing duct. Wing-heated air is exhausted through a louver on the top surface of the tip. Wing position lights are located at the center of the tip
and are not directly visible from the cockpit. AB an indication that the wing tip light is operating, some wing tips are equipped with a lucite rod to transmit the light to the leading edge.
Figure 1-20 shows a cross sectional view of an
Access door
Corrugated inner skin
FxctlRB 1-19. Removable wing tip.
Anti-icing exhaust air outlet
FxctlRB 1-20. All-metal wing with chemically milled clwmela.
all-metal full cantilever {no external bracing) wing section. The wing is made up of spars, ribs, and lower and upper wing skin covering. With few exceptions, wings of this type are of the stressed-skin design (the skin is part of the wing structure and carries part of the wing stresses).
The top and bottom wing skin covers are made up of several integrally stiffened sections. This type of wing construction permits the. installation of bladder-type fuel celfs in the wings or is sealed to hold fuel without the usual fuel cells or tanks. A
w~g which is constructed to allow it to be used as a fuel cell or tank is referred to as a "wet-wing."
A wing that uses a box-beam design is shown in figure 1-21. This type of construction not only increases strength and reduces weight, but it also enables the wing to serve as a fuel tank when prop· erly sealed.
FiGURE 1-21. Box-beam milled wing.
Both aluminum honeycomb and fiber glass honeycomb sandwich material are commonly used in the construction of wing a~d stabilizer surfaces, bulkheads, floors, control surfaces, and trim tabs. Alu-
inum honeycomb material is made of aluminum foil honeycomb core, bonded between sheets of aluminum. Fiber glass honeycomb material consists of fiber glass honeycomb core bonded between layers of fiber glass cloth.
In the construction of large aircraft structures, and in some small aircraft as well, the honeycomb sandwich structure employs either aluminum or reinforced plastic materials. Honeycomb panels are usually a lightweight cellular core sandwiched between two thin skins or facing materials such as aluminum, wood, or plastic.
Aircraft honeycomb material is manufactured in various shapes, but is usually of the constant thickness or tapered core types. An example of each is shown in figure 1-22.
13
Core Skin
l
l
-
~ ,
\ Skin A. Constant thickness
Le Skin
:--,JiTTTTI] lln,..IIIII---IIIID 1111111111111 1{ I""
- Skin
B. Tapered core
FiGURE 1-22. Constant-thickness and tapered-core
honeycomb sections.
Figure 1-23 shows a view of the upper surface of a large jet transport wing. The various panels manufactured from honeycomb material are outlined by diagonal lines and labeled.
Still another type of construction is illustrated in figure 1-24. In this case the sandwich structure of the wing leading edge is bonded to the metal spar. Also shown is the integrally bonded deicer panel.
NACELLES OR PODS
Nacelles or pods are streamlined enclosures used on multi-engine aircraft primarily to house the en· gines. They are round or spherical in shape and are usually located above, below, or at the leading edge of the wing on multi-engine aircraft. If an aircraft has only one engine, it is usually mounted at the forward end of the fuselage, and the nacelle is the streamlined extension of the fuselage.
NACELLES OR PODS
An engine nacelie or pod consists of skin, cowling, structural members, a firewall, and engine mounts. Skin and cowling cover the outside of the nacelle. Both are usually made of sheet aluminum alloy, stainless steel, magnesium, or titanium. Regardless of the material used, the skin is usually attached to the framework by rivets.
The framework usually consists of structural members similar to those of the fuselage. The framework includes lengthwise members, such as
Trailing edge sandwich panels
(constant-thickness core)
Trailing edge sandwich panel
(constant-thickness core)
Spoiler sandwich panel (tapered core, solid wedge)
Trailing edge sandwich panels
(constant-thickness core)
Spoiler sandwich panel (tapered core, solid wedge)
Aileron tab sandwich panels (tapered core, phenolic wedge)
Aileron sandwich panel (constant-thickness core)
Trailing edge wedge sandwich panel
(tapered core, cord wedge)
FIGURE 1-23. Honeycomb wing construction on a large jet transport aircraft.
longerons and stringers, and widthwise/vertical members, such as bulkheads, rings, and formers.
A nacelle or pod also contains a firewall which separates the engine compartment from the rest of the aircraft. This bulkhead is usually made of stainless steel sheet metal, or as in some aircraft, of titanium.
Another nacelle or pod member is the engine mount. The mount is usually attached to the firewall, and the engine is attached to the mount by nuts, bolts, and vibration-absorbing rubber cushions or pads. Figure 1-25. shows examples of a semimonocoque and a welded tubular steel engine mount used with reciprocating engines.
Engine mounts are designed to meet particular conditions of installation, such as the location and the method of attachment of the engine mount and the size, type, and characteristics of the engine it is intended to support. An engine mount is usually constructed as a single unit which can be detached
14
quickly and easily from the remaining structure. Engine mounts are commonly made of welded chrome/molybdenum steel tubing, and forgings of chrome/nickel/molybdenum are used for the highly stressed fittings.
To reduce wind resistance during flight, the landing gear of most high-speed or large aircraft is retracted (drawn up into streamlined enclosures). The part of the aircraft which receives or encloses the landing gear as it retracts is called a wheel well. In many instances, the wheel well is part of the nacelle; however, on some aircraft the landing gear retracts into the fuselage or wing.
Cowling
Cowling usually refers to the detachable covering of those areas into which access must be gained regularly, such as engines, accessory sections, and engine mount or firewall areas. Figure 1-26 shows an exploded view of the pieces oi cowling for a horizontally opposed engine on a light aircraft.
Deicer panel with
chordwise ribs
Laminated metal structure
Glass reinforced p1astics
sandwich faces Wooden members spanwise and chordwise
FJcuu 1-24. Leading edp aaDdwieh material bonded to metal wiDg member.
FIGtJU 1-25. Semimonoc:oque and welded tubular
llteel eqiDe mounts.
Some large reciprocating engines are eocloaed by "orange-peel" cowl panels. The cowl panels are attached to the firewall by mounts which aJao l!el'Ve as binges when the cowl ia opened {figure 1-27).
The lower cowl mounts are eecured to the binge bracbla by pilll which automatically lock in pJace,
15
Ficuu 1-26. Cowq for horizontally oppoeed eaaiJae.
but can be removed by simply pulling on a ring. The side panels are held open by short rods; the top panel is held open by a longer rod, and the lower panel ia restrained in the "open" position by a spring and cable.
All four panela are locked in the "closed" posi· tion by over-center steel latches, which are secured
FIGURE 1-27. "Orange-peel" cowling opened.
in the closed position by spring-loaded safety catches. Cowl panels are generally of aluminum alloy construction; however, stainless steel is generally used as the inner skin aft of the power section, for cowl flaps and near the cowl flap openings, and for oil cooler ducts.
On turbojet engine installations, cowl panels are designed to provide a smooth airflow over the engines and to protect the engine from damage. The entire engine cowling system includes a nose cowl, upper and lower hinged removable cowl panels, and fixed cowl panel. Typical upper and lower hinged removable panels are shown in figure 1-28.
EMPENNAGE
The empennage is also called the tail section and most aircraft designs consist of a tail cone, fixed surfaces, and movable surfaces.
16
The tail cone serves to close and streamline the aft end of most fuselages. The cone is made up of structural members (figure 1-29) like those of the fuselage; however, cones- are usually of lighter construction since they receive less stress than the fuselage.
Other components of the typical empennage are of heavier construction than the tail cone. These members include fixed surfaces that help steady the aircraft and movable surfaces that help to direct an aircraft's flighL The fixed surfaces are the horizon· tal and vertical stabilizers. The movable surfaces are usually a rudder and elevators.
Figure 1-30 shows how the vertical surfaces are braced, using spars, ribs, stringers, and skin in a similar manner to the systems used in a wing.
Stress in an empennage is also carried like stress
Hold open rod
Forward
snubber
Hold open rod
FIGURE l-28. Side·mounted turbojet engine cowling.
in a wing. Bending, torsion, and shear, created by airioads, pass from one structural member to another. Each member absorbs some of the stress and Vertical stabilizer passes the remainder to other m$lmbers. The overload of stress eventually reaches the spars, which
transmit it to the fuselage structure.
FIGURE 1-29. The fuselage terminates in a tail cone.
17
Rudder
FIGURE 1-30. Construction features of rudder and
vertical stabilizer.
RIGHT CONTROL SURFACES
RIGHT CONTROL SURFACES
The directional control of a fixed-wing aircraft tabs place around the lateral, longitudinal, and vertical uee by means of flight control surfaces. These control devices are hinged or movable surfaces through which the attitude of an aircraft is controlled during takeoff, flight, and landing. They are usually divided into two major groups, the pri· mary or main, and the auxiliary control surfaces.
The primary group of flight control surfaces con· si8fll of ailerons, elevators, and rudders. Ailerons
are attached to the trailing edge of both wings of an aircraft. Elevators are attached to the trailing edge of the horizontal stabilizer. The rudder is hinged to the trailing edge of the vertical stabilizer.
Primary control aurfaces are similar in construction and vary only in size, shape, and methods of attachment. In construction, control surfaces are similar to the all-metal wing. They ~ usually made of an aluminum alloy structure built around a sin· gle spar member or torque· tube. Ribs are fitted to the spar at the leading and trailing edges and are joined together with a metal strip. The ribs, in many cases, are formed from flat sheet stock. They are seldom solid; more often, the formed, stamped· out ribs are reduced in weight by holes which are punched in the metal.
The control surfaces of some aircraft are fabric covered. However, all turbojet powered aircraft have metal-covered surfaces for additional strength.
The control surfaces previously described can be considered conventional, but on some aircraft, a control surface may serve a dual purpose. For ex· ample, one set of control surfaces, the elevons, com· binee the functions of both ailerons and elevators. Flaperons are ailerons which can also act 88 flaps. A movable horizontal tail section is a control surface which supplies the action of both the horizon· tal stabilizer and the elevators.
The secondary or auxiliary group of control sur· faces conaists of such members 88 trim tabs, balance tabs, servo tabs, flaps, spoilers, and leading edge devicee. Their purpose is to reduce the force required to actuate the primary controls, to trim and balance the aircraft in flight, to reduce landing speed or shorten the length of the landing roll, and to dumge the speed of the S:rcraft in ·flight. They are uaually attached to, or recessed in, the main coutrol surfaces.
Ailerons
Ailerons are primary control surfaces which
18
make up part of the total wing area. They are movable through a pre-designed arc and are usually hinged to the aileron spar or rear wing spar. The ailerons are operated by a lateral (side-to-side) movement .Jf the aircraft control stick, or a turning motion of the wheel on the yokeo·
In a coavenbonal configuration, one ailer~n is hinged to the outboard trailing edge of each wing. Figure 1-31 ahows the shape and location of typical small-aircraft ailerons on varioua wing-tip designs.
A B
c
FIGuu 1~1. Aileron location OD YBrioua wiDJ·tip daipe.
The ailerons are interconnected in the control system to operate simultaneously in opposite directions. As one aileron moves downward to increase lift on its side of the fuselage, the aileron on the opposite side of the fuselage moves upward to decrease lift on its side. This opposing action results in more lift being produced by the wing on one side of the fuselage than on the other, resulting in a controlled movement or roll due to unequal aerodynamic forces on the wingL
An end view of a typical metal rib in an aileron is shown in figure 1-32. The hinge point of this type of aileron is behind the leading edge of the aileron to provide a more sensitive response to con· trol movements. The horns attached to the aileron spar are levers to which the aileron control cables are secured.
Aileron hinge-pin
fitting
Actuating hom
Lightening hole
FIGURE 1-32. End view of aileron rib.
Large aircraft may use all-metal ailerons, except for fiber glass trailing edges, hinged to the rear
wing spar in at least four places. Figure 1-33 lihows several examples of aileron installation.
FIGURE 1-33. Aileron hinge locations.
All the control surfaces of a large turbojet aircraft are shown in figure 1-34. As illustrated, each
wing has two ailerons, one in the conventional position at the outboard trailing edge of the wing and another hinged to the trailing edge of the wing center section.
The complex lateral control system in large turbojet aircraft is far more sophisticated than the type employed in a light airplane. During low-speed Bight all lateral control surfaces operate to provide
19
maximum stability. This includes all four ailerons, flaps, and spoilers. At high speeds, flaps are re· tracted and the outboard ailerons are locked out of the aileron control system.
The major part of the skin area of the inboard ailerons is aluminum honeycomb panels. Exposed honeycomb edges are covered with sealant and protective finish. The aileron nose tapers and extends forward of the aileron hinge line. Each inboard aileron is positioned between the inboard and out·
~Outboard aileron
\ … ---Balance tab
~Outboard spoilers
Outboard flap
~
/
Vortex generators
,...,.. , … ton"''""'-.... u.ae ,,.hoi" ....,.tt.
Leading edge flaps
elevator tab
control tab
board flaps at the trailing edge of the wing. The aileron hinge supports extend aft and are attached to aileron hinge bearings to support the aileron.
The outboard ailerons are made up of a nose spar and ribs covered with aluminum honeycomb panels. A continuous hinge attached to the forward edge of the nose is grooved to mate with the hem of a fabric seal.
The outboard ailerons are located in the trailing edge of each outboard wing section. Hinge supports extend aft from the wing and are attached to the aileron hinge bearing to support the aileron. The nose of the aileron extends into a balance chamber in the wing and is attached to balance panels.
Aileron balance panels (figure 1-35) reduce the force necessary to position and hold the ailerons. The balance panels may be made of aluminum honeycomb skin bonded to an aluminum frame, or of
WING
aluminum skin-covered assemblies with hat-section stiffeners. Clearance between the aileron nose and wing structure provides a controlled airflow area necessary for balance panel action. Seals attached to the panels control air leakage.
Air loads on the balance panels (figure 1-35) depend on aileron position. When the ailerons are moved during flight to either side of the streamline position, differential pressure is created across the balance panels. This differential pressure acts on the balance panels in a direction that assists aileron movement. Full balance panel force is not required for small angles of aileron displacement because the manual force necessary to rotate the control tab through small angles is slight. A controlled air bleed is progressively decreased as the aileron displacement angle is increased. This action increases the differential air pressure on the balance panels as
AILERON
FIGURE 1-35. Aileron balance panel.
the ailerons rotate from the streamline position. The increasing load on the balance panel counteracts the increasing load on the ailerons.
Auxiliary Wing Flight Surfaces
The ailerons are the primary wing flight surfaces. Auxiliary wing flight surfaces include trailing edge flaps, leading edge flaps, speed brakes, spoilers, and leading edge slats. The number and type of auxiliary wing flap surfaces on an aircraft vary widely, depending on the type and size of aircraft.
Wing flaps are used to give the aircraft extra lift. They reduce the landing speed, thereby shortening
the length of the landing rollout to facilitate landing in small or obstructed areas by permitting the gliding angle to be increased without greatly in-
21
creasing the approach speed. In addition, the use of flaps during takeoff reduces the length of the takeoff run.
Most flaps are hinged to the lower trailing edges of the wings, inboard of the ailerons. Leading edge flaps are also used, principally on large high-speed aircraft. When they are in the "up" (or retracted) position, they fair in with the wings and serve as part of the wing trailing edge. When in the "down"
(or extended) position, the flaps pivot on the hinge points and drop to about a 45 ° or 50° angle with the wing chord line. This increases the wing camber and changes the airflow, providing greater lift.
Some common types of flaps are shown in figure 1-36. The plain flap (figure 1-36A) forms the trailing edge of the wing when the flap is in the up (or
A. Plain flap (down)
B. Split flap (down)
C. Fowler flap (down)
FIGURE 1-36. Wing ftaps.
retracted) position. It contains both the upper and lower surface of the wing trailing edge.
The plain split flap (figure l-36B) is normally housed flush with the undersurface of the wing. It is similar to a plain flap except that the upper surface of the wing extends to the flap trailing edge
and does not ·droop with the flap. This flap is also called the split-edge flap. It is usually just a braced, flat metal plate hinged at several points along its leading edge.
Aircraft requiring extra wing area to aid lift often use Fowler flaps (figure l-36C) . This system houses the flaps flush under the wings much as does the plain split flap system. But, instead of the flaps hinging straight down from a stationary hinge line, worm-gear drives move the flaps leading edge rearward as the flaps droop. This action provides normal flap effect, and, at the same time, wing area is increased when the flaps are extended.
An example of a triple-slotted segmented flap used on some large turbine aircraft is shown in figure l-37. This type of trailing edge flap system provides high lift for both takeoff and landing. Each flap consists of a foreflap, a mid-flap, and an aft-flap. The chord length of each flap expands as the flap is extended, providing greatly increased
22
Aft flap~
FIGURE 1-37. Triple-slotted trailing edge ftaps.
flap area. The resulting slots between flaps prevents separation of the airflow over the flap area.
The leading edge flap (figure l-38) is similar in operation to the plain flap; that is, it is hinged on the bottom side, and, when actuated, the leading edge of the wing extends in a downward direction to increase the camber of the wing. Leading edge flaps are used in conjunction with other types of flaps.
FIGURE 1-38. Cross section of a leading edge ftap.
Figure l-34 shows the location of the leading edge flaps on a large multi-engine turbine aircraft. Three Kruger-type flaps are installed on each wing. The flaps are machined magnesium castings with integral ribs and stiffeners. The magnesium casting of each flap is the principal structural component and consists of a straight section with a hollow core called the torque tube extending from the straight section at the forward end.
Each leading edge flap has three gooseneck hinges attached to fittings in the fixed wing leading edge, and a hinged fairing is installed on the trailing edge of each flap. Figure l-39 shows a typical leading edge flap in retracted position, with an outline of the extended position.
Speed brakes, sometimes called dive flaps or dive brakes, serve to slow an aircraft in flight. These brakes are used when descending at a steep angle or when approaching the runway for a landing. The brakes themselves are manufactured in many
•• , ... · , I I I ' ' • • .._ F1ap extended • I • • \ ... ,.__Retractable DOle
F1ap retracted
F'JGUD 1-39. Leadiq ed1e flap.
shapes, and their location depends on the design of the aircraft and the purpose of the brakes.
The brake panels may be located on certain parts of the fuselage or on the wing surfaces. Brakes on the fuselage are small panels that can be extended into the smooth airflow to create turbulence and drag. Wing-type brakes may be multiple-finger channels extending above and below the wing surfaces to break up smooth airftow. Usually speed brakes are controlled by electrical switches and
actuated by hydraulic pressure.
Another type of air brake is a combination of spoilers and speed brakes. A typical combination consists of spoiler flaps located in the upper wing surfaces ahead of the ailerons. When the operator wishes to use both air brakes and spoilers, he can slow the flight speed and maintain lateral control as welL
Spoilers are auxiliary wing flight control surfaces, mounted on the upper surface of each wing, which operate in conjunction with the ailerons to provide lateral controL
Most spoiler systems can also be extended symmetrically to serve a secondary function as speed brakes. Other systems are equipped with separate ground and flight spoilers. Most spoiler panels are bonded honeycomb structures with aluminum skin. They are attached to the wing structure by machined hinge fittings which are bonded into the spoiler paneL
Tabs
One of the simplest yet most important devices to
aid the pilot of an aircraft is the tab attached to a control surface. Although a tab does not take the place of a control surface, it is mounted on or attached to a movable control surface and causes easier movement or better balance of the control surface.
All aircraft, except a few of the very lightest types, are equipped with tabs that can be controlled from the cockpit. Tabs on some of these aircraft are usually adjustable only when the aircraft .is on the ground. Figure 1-40 shows the location of a typical rudder tab.
Hinge line
Fuselage
4 Aircraft movement
4 Aircraft movement
FJGVU 1-40. Typical location of rudder control tab.
LANDING GEAR
The landing gear is the assembly that supports the aircraft during landing or while it is resting or moving about on the ground. The landing gear has shock struts to absorb the shock of landing and taxiing. By means of a gear-retraction mechanism, the landing gear attachell to the aircraft structure and enables the gear to extend and retract. The landing gear arrangement either has a tailwheel or a nosewheel. Landing gear arrangements having a nosewheel are usually equipped for nosewheel steering. Nosewheel aircraft are protected at the fuselage tail section with a tail skid or bumper. By means of wheels and tires (or skis), the landing gear forms a stabilizing contact with the ground during landing and taxiing. Brakes installed in the wheels enable the aircraft to be slowed or stopped during movement on the ground.
SKIN AND FAIRING
SKIN AND FAIRING
The smooth outer cover of the ain;raft is referred to as skin. The skin covers the fuselage, wings, empennage, nacelles, and pods. The material used for the skin covering is usually sheet aluminum alloy, treated so that it will not corrode. Magnesium and stainless steel may also be used to a limited extent. The thickness of the skin materials covering
a structural unit may difter, depending on the load and stresses imposed within and throughout the structure. To smooth out the airflow over the angles formed by the wings and other structural units with the fuselage, shaped and rounded panels or metal skin are attached. This paneling or skin is called fairing. Fairing is sometimes referred to as a fillet. Some fairing is removable to provide access to air· craft components, whereas other fairing is riveted to the aircraft structure.
ACCESS AND INSPECTION DOORS
ACCESS AND INSPECTION DOORS
Access doors permit normal or emergency entrance into or exit from the aircraft. Also, they provide access to servicing points and man· ually operated drains. Inspection doors provide access to a particular part of . the aircraft being inspected or maintained. Access or inspection doors are either hinged or removable. They are fastened in the closed position with catch and lock· ing mechanisms, screws, quick-release devices, or cowling type fasteners. Access and inspection doors that are removable often have a stenciled identifies· tion number that is identical to a number stenciled near the opening that they cover. Other access and inspection doors have a stenciled nomenclature to identify the opening that they cover.
HRICOPTER STRUCTURES
HRICOPTER STRUCTURES
Like the fuselages in fixed-wing aircraft, helicopter fuselages may be welded truss or some form of monocoque construction. Although their fuselage configurations may vary a great deal, most helicopter fuselages employ structural members similar to those used in fixed-wing aircraft. For example, most helicopters have such vertical/widthwise braces as bulkheads, formers, rings, and frames. They are also provided with such lengthwise braces as stringers and longerons. In addition, the gussets, joiners, and skin hold the other structural · members together.
The basic body and tail boom sections of a typi·
cal helicopter are of conventional, all-metal, riveted structures incorporating formed aluminuiD alloy bulkheads, beams, channels, and stiffeners. Stressed skin panels may be either smooth or beaded. The firewall and engine deck are usually stainl8Ss steel. The tail boom is normally of semimonocoque construction, made up of formed aluminum bulkheads, extruded longerons, and skin panels or of welded tubular steel.
The major structural components of one type of helicopter are shown in figure 1-41. The membe~ of a helicopter's tail group vary widely, depending on the individual type and design. In this case, a · stabilizer is mounted on a pylon to make up the group. In other cases, the stabilizer may be mounted on the helicopter tail cone or fuselage. In either case, both the pylon and stabilizer usually contain aluminum alloy structural members covered with magnesium alloy skin. The types of structural members used, however, usually vary. A pylon usually has bulkheads, formers, frames, stringers, and beams, making it somewhat of a blend of aircraft wing and fuselage structural members. The
~tabilizer is usually built more like an aircraft wing, with ribs and spars.
In a typical helicopter, the tail, body, and tail boom are constructed of all-metal stressed skin and metal reinforcing members. The helicopter cabin is normally a plexiglass enclosure which is supported by aluminum tubing in some models.
A large single-rotor helicopter is shown in figure 1-42. It is all-metal and is basically composed of two major sections, the cabin and the tail cone. The cabin section is further divided into passenger or cargo compartments, which provide space for the crew, passengers, cargo, fuel and oil tanks, controls, and powerplant. In multi-engine helicopters, the powerplants are usually mounted in separate engine nacelles.
As shown in figure 1-42, the aft section of a trpical single-rotor helicopter consists of the tail cone, the fin, the tail-cone housing, the tail-rotor pylon, and the tail-end fairing. The tail cone is bolted to the rear of the forward section and supports the tail rotor, tail-rotor drive shafts, stabilizers, tail-cone housing, and tail-rotor pylon. The tail cone is of magnesium alloy and aluminum alloy construction. The tail-cone housing is bolted to the aft end of the tail cone. Trim stabilizers extend out
Main rotor
Stabilizer Tail rotor
DO
Main gear Forward section
FIGURE 1-U. Typical helicopter structural components.
J
CABIN SECTION
CABIN SECTION
K
TAIL CONE SECTION
H. Fin
J. Tail cone K. Tail-cone housing
A. Engine compartment E. Fuel tank compartment L. Pylon
B. Cockpit F. Baggage compartment M. Tail-end fairing
C. Transmission compartment
D. Cabin
G. Electrical and radio
compartment
FIGURE 1-42. Location of major helicopter components.
TAIL CONE SECTION
on both sides of the tail cone forward of the housing.
Helicopter structural members are designed to carry a load or, stated differently, to resist stress. A single member of the helicopter structure may be subjected to a combination of stresses. In most cases it is desirable for structural members to carry end loads rather than side loads; that is, to be subjected to tension or compression rather than bending. Structural members are usually combined
into a truss to carry end loads. In a typical Pratt truss, the longitudinal and vertical members are tubes or rods capable of carrying compression loads.
Nonstructural members that are not removable from the helicopter are usually attached by riveting or spot welding. Riveting is the most common method of attaching aluminum alloy sheets together. Parts that can be removed from the helicopter struc· tore are usually bolted together.
Transparent materials are W!ed for windshields and windows and sometimes to cover parts requiring frequent visual inspection. Transparent plastic sheet and laminated glass are the materials most commonly used.
Some helicopter manufacturers use impregnated glass cloth laminate (fiber glass) as a lightweight substitute for certain metal parts, since fiber glass is simple to manufacture, haa a high strength-weight
ratio, and resists mildew, corrosion, and rot.
GENERAL
This chapter includes both assembly and rigging since the subjects are directly related. Assembly involves putting together the component sections of the aircraft, such as wing sections, empennage units, nacelles, and landing gear. Rigging is the final adjustment and alignment of the various component sections to provide the proper aerodynamic reaction.
Two important considerations in all assembly and rigging operations are: ( 1) Proper operation of the component in regard to its aerodynamic and mechanical function, and (2) maintaining the aircraft's structural integrity by the correct use of materials, hardware, and safetying devices. Improper assembly and rigging may result in certain members being subjected to loads greater than those for which they were designed.
Assembly and rigging must be done in accordance with the requirements prescribed by the aircraft manufacturer. These procedures are usually detailed in the applicable maintenance or service manuals. The Aircraft Specification or Type Certificate Data Sheets also provide valuable information regarding control surface travel.
The rigging of control syatems varies with each type of aircraft, therefore, it would be impracticable to define a precise procedure. However, certa.in principles apply in all situations and these will be
disc~d in this chapter. It is essential that the aircraft manufacturer's instructions be followed when rigging an aircraft.
THEORY OF FLIGHT
THEORY OF FLIGHT
Numerous comprehensive texts have been written about the aerodynamics involved in the flight of an aircraft. It is unnecessary that a mechanic be totally versed on the subjecL However, he must understand the relationships between the atmosphere, the aircraft, and the forces acting on it in flight, in order to make intelligent decisions affecting the flight safety of both airplanes al!d helicopters.
Understanding why the aircraft is designed with
27
CHAPTER 2
CHAPTER 2
ASSEMBLY AND RIGGING
a particular type of primary and secondary control system, and why the surfaces must be aerodynamically smooth, becomes essential when maintaining today's complex aircraft.
AERODYNAMICS
Theory of flight deals with aerodynamics. The term aerodynamics is derived from the combination of two Greek words--"aer" meaning air, and "dyne" meaning force of power. Thus, when aero is joined with dynamics, we have aerodynamics, meaning the study of objects in motion through the air and the forces that produce or change such motion.
ASSEMBLY AND RIGGING
Aerodynamics is the science of the action of air on an object. It is further defined as that branch of dynamics which deals with the motion of air and other gases, with the forces acting upon an object in motion through the air, or with an object which is stationary in a current of air. In effect, aerodynamics is concerned with three distinct parts. These parts may be defined as the aircraft, the relative wind, and the atmosnhere.
THE ATMOSPHERE
THE ATMOSPHERE
Before discussing the fundamentals of the theory of flight, there are several basic ideas that must be considered. An aircraft operates in the air; therefore, the properties of air that affect aircraft control and performance must be understood.
Air is a mixture of gases composed principally of nitrogen and oxygen. Since air is a combination of gases, it follows the laws of gases. Air is considered a fluid because it answers the definition of a fluid, namely, a substance which may be made to flow or change its shape by the application of moderate pressure. Air has weight, since something lighter than air, such as a balloon filled with helium, will rise in the air.
PRESSURE
The deeper a diver goes beneath the surface of the ocean, the greater the pressure becomes on his body due to the weight of the water overhead. Since air also has weight, the greater the depth from the
outer surface of the atmosphere, the greater the pressure. If a l-in. square column of air extending from sea level to the "top" of the atmosphere could be weighed, it would be found to weigh about 14.7 lbs. Thus, atmospheric pressure at sea level is 14.7 p.s.i. (pounds per square inch). However, pounds per square inch is rather a crude unit for the m~asurement of a light substance such as air. Therefore, atmospheric pressure is usually measured in terms of inches of mercury.
The apparatus for measuring atmospheric pres· sure is shown in figure 2-1. A glass tube, 36 in. long, open at one end, and closed at the other, is filled with mercury. The open end is sealed tempo· rarily and then submerged into a small container partly filled with mercury, after which the end is unsealed. This allows the mercury in the tube to descend, leaving a vacuum at the top of the tube. Some of the mercury flows into the container while a portion of it remains in the tube. The weight of the atmosphere pressing on ·the mercury in the open container exactly balances the weight of the mer· cury in the tube, which has no atmospheric pressure pushing down on it due to the vacuum in the top of the tube. As the pressure of the surrounding air decreases or increases, the mercury column lowers or rises correspondingly. At sea level the height of the mercury in the tube measures approximately 29.92 in., although it varies slightly with atmospheric conditions.
An important consideration is that atmospheric pressure varies with altitude. The higher an object rises above sea level, the lower the pressure. V ar· ious atmospheric conditions have a definite relation to flying. The effect of temperature, altitude, and density of the air on aircraft performance is dis· cussed in the following paragraphs.
DENSITY
Density is a term that means weight per unit volume. Since air is a mixture of gases, it can be compressed. If the air in one container is under one-half as much pressure as the air in another identical container, the air under the greater pres· sure weighs twice as much as that in the container under lower pressure. The air under greater pres· sure is twice as dense as that in the other container. For equal weights of air, that which is under the greater pressure occupies only half the volume of that under half the pressure.
The density of gases is governed by the following rules:
28
Vacuum
Atmospheric pressure acting
on ~'Urface of
mercury
FIGURE 2-1. Measurement of atmospheric pressure.
( 1) Density varies in direct proportion with
the pressure. (2) Density varies inversely with the tempera-
ture. Thus, air at high altitudes is less dense than air at low altitudes, and a mass of hot air is less dense than a mass of cool air.
Changes in density affect the aerodynamic per· formance of aircraft. With the same horsepower, an aircraft can fly faster at a high altitude where the density is low than at a low altitude where the density is great. This is because air offers less resistance to the aircraft when it contains a smaller number of air particles per unit volume.
HUMIDITY
Humidity is the amount of water vapor in the air. The maximum amount of water vapor that air can hold varies with the temperature. The higher the temperature of the air, the more water vapor it can absorb. By itself, water vapor weighs approximately
five-eighths as much as an equal amount of per· fectly dry air. Therefore, when air contains water vapor it is not as heavy as air containing no mois· ture.
Assuming that the temperature and pressure remain the same, the density of the air varies in· versely with the humidity. On damp days the air density is less than on dry days. For this reason, an aircraft requires a longer runway for takeoff on damp days than it does on dry days.
BERNOULU'S PRINCIPLE AND SUBSONIC FLOW
BERNOULU'S PRINCIPLE AND SUBSONIC FLOW
Bernoulli's principle states that when a fluid (air) flowing through a tube reaches a constriction, or narrowing of the tube, the speed of the fluid flowing through that constriction is increased and its pressure is decreased. The cambered (curved) surface of an airfoil (wing) affects the airflow ex-
actly as a constriction in a tube affects airflow. This resemblance is illustrated in figure 2-2.
pressure pressure
A
B
F'JcURE 2-2. Bernoulli's principle.
pressure
Diagram A of figure 2-2 illustrates the effect of air passing through a constriction in a tube. In B, the air is flowing past a cambered surface, such as an airfoil, and ·the effect is similar to that of air passing through a restriction.
As the air flows over the upper surface of an airfoil, its speed or velocity increases and its pressure decreases. An area of low pressure is thus formed. There is an area of greater pressure on the lower surface of the airfoil, and this greater pressure tends to move the wing upward. This difference in pressure between the upper and lower surfaces of the wing is called lift. Three-fourths of the total lift
of an airfoil is the result of the decrease in pressure over the upper surface. The impact of air on the under surface of an airfoil produces the other onefourth of the total lift.
An aircraft in flight is acted upon by four forces:
(1) Gravity, or weight, the force that pulls the
aircraft toward the earth. (2) Lift, the force that pushes the aircraft up·
ward. (3) Thrust, the force that moves the aircraft
forward. ( 4) Drag, the force that exerts a braking
action.
MOTION
Motion is the act or process of changing place or position. An object may be in motion with respect to one object and motionless with respect to an· other. For example, a person sitting quietly in an aircraft flying at 200 knots is at rest or motionless with respect to the aircraft; however, the person is in motion with respect to the air or the· earth, the same as is the aircraft.
Air has no force or power, except pressure, un· less it is in motion. When it is moving, however, its force becomes apparent. A moving object in motionless air has a force exerted on it as a result of its own motion. It makes no difference in the effect then, whether an object is moving with respect to the air or the air is moving with respect to the object.
The flow of air around an object caused by the movement of either the air or the object, or both, is called the relative wind.
Velocity and Acceleration
The terms "speed" and "velocity" are often used interchangeably, but they do not mean the same. Speed is the rate of motion, and velocity is the rate of motion in a particular direction in relation to time.
An aircraft starts from New York City and flies 10 hrs. at an average speed of 260 m.p.h. At the end of this time the aircraft may be over the Atlantic Ocean, the Pacific Ocean, the Gulf of Mexico, or, if its flight were in a circular path, it may even be back over New York~ If this same aircraft flew at a velocity of 260 m.p.h. in a southwestward direction, it would arrive in Los Angeles in about 10 hrs. Only the rate of motion is indicated in the first example and denotes the speed of the aircraft. In the last example, the particular direction is in·
eluded with the rate of motion, thus, denoting the velocity of the aircraft.
Acceleration is defined as the rate of change of velocity. An aircraft increasing in velocity is an example of positive acceleration, while another air· craft reducing its velocity is an example of negative acceleration. (Positive acceleration is often referred to as acceleration and negative acceleration as de· celeration.)
Newton's Laws of Motion
The fundamental laws governing the action of air about a wing are Newton's laws of motion.
Newton's first law is normally referred to as the law of inertia. It simply means that a body at rest will not move unless force is applied to it. If it is moving at uniform speed in a straight line, force must be applied to increase or decrease that speed.
Since air has mass, it is a "body" in the meaning of the law. When an aircraft is on the ground with its engines stopped, inertia keeps the aircraft at rest. An ai:rcraft is moved from its state of rest by the thrust force created by the propeller, by the expanding exhaust gases, or both. When it is flying at uniform speed in a straight line, inertia tends to keep the aircraft moving. Some external force is required to change the aircraft from its path of flight.
Newton's second law, that of force, also applies to objects. This law states that if a body moving with uniform speed is acted upon by an external force, the change of motion will be proportional to the amount of the force, and motion will take place in the direction in which the force acts. This law may be stated mathematically as follows:
Force= mass X acceleration (F =rna). If an aircraft is flying against a headwind, it is slowed down. If the wind is coming from either side of the aircraft's heading, the aircraft is pushed off course unless the pilot takes corrective action against the wind direction.
Newton's third law is the law of action and reac· tion. This law states that for every action (force) there is an equal and opposite reaction (force). This law is well illustrated by the action of a swim· mer's hands. He pushes the water aft and thereby propels himself forward, since the water resists the action of his hands. When the force of lift on an aircraft's wing equals the force of gravity, the aircraft maintains level flight.
The three laws of motion which have been discussed are closely related and apply to the theory of
30
flighL In many cases, all three laws may be operating on an aircraft at the same time.
AIRFOILS,
An airfoil is a surface designed to obtain a desirable reaction from the air through which it moves. Thus, we can say that any part of the aircraft which converts air resistance into a force useful for flight is an airfoiL The blades of a propeller are so designed that when they rotate, their shape and position cause a higher pressure to be built up behind them than in front oj them so that they will pull the aircraft forward. The profile of a conventional wing, shown in figure 2-3, is an excellent example of an airfoil. Notice that the top surface of the wing profile has greater curvature than the lower surface.
FrcURE 2-3. Airflow over a wing section.
The difference in curvature of the upper and lower surfaces of the wing builds up the lift force. Air flowing over the top surface of the wing must reach the trailing edge of the wing in the same amount of time as the air flowing under the wing. To do this, the air passing over the top surface
moves at a greater velocity than the air passing below the wing because of the greater distance it must travel along the top surface. This increased velocity, according to Bernoulli's principle, means a corresponding decrease in pressure on the surface. Thus, a pressure differential is created between the
upper and lower surfaces of the wing, forcing the wing upward in the direction of the lower pressure.
The theoretical amount of lift of the airfoil at a velocity of 100 m.p.h. can be determined by sampling the pressure above and below the airfoil at the point of greatest air velocity. As shown in figure 2-3, this pressure is 14.54 p.s.i. above the airfoil. Subtracting this pressure from the pressure below the airfoil, 14.67, gives a difference in pressure of 0.13 p.s.i. Multiplying 0.13 by 144 (number of square inches in a square foot) shows that each
square foot of this wing will lift 18.72 pounds. Thus, it can be seen that a small pressure di1feren· tial across an airfoil section can produce a large lifting force. Within limits, lift can be increased by increasing the angle of attack, the wing area, the freestream velocity, or the density of the air, or by changing the shape of the airfoil.
Angle of Attack
Before beginning the discussion on angle of attack and its effect on airfoils, we shall first consider the terms "chord" and "center of pressure."
The chord of an airfoil or wing section is an imaginary straight line which passes through the section from the leading edge to the trailing edge, as shown in figure 2-4.. The chord line provides one side of an angle which ultimately forms the angle of attack. The other side of the angle is formed by a line indicating the direction of the relative airstream. Thus, angle of attack is defined as the angle between the chord line of the wing and the direction of the relative wind. This is not to be confused with the angle of incidence, which is the angle between the chord line of the wing and the longitu· dinal axis of the aircraft.
FIGURE 2-4. Positive angle of attack.
On each minute part of an airf9il or wing surface, a small force is presenL This force is different in magnitude and direction from any forces acting on other areas forward or rearward from this point. It is possible to add all of these small forces mathematically, and the siun is called the resultant force
(lift). This resultant force has magnitude, direction, and location, and can be represented as a vector, as shown in figure 2-4. The point of intersection of the resultant force line with the chord line of the airfoil is called the center of pressure. The center of pressure moves along the airfoil chord as the angle of attack changes. Throughout most of the ftight range, the center of pressure moves forward with increasing angle of attack and rearward as the
31
angle of attack decreases. The effect of increasing angle of attack on the center of pressure is shown in figure 2-5.
An~lt• of attad< = o•
Rt•sultant Rt'lativl' ' . , :\t•):ativt• prt•,sur<· air-t n·am ,: ·- patlt•rn = ~~-~-~·~· .. ~P~os~it~iv~e0~pr~l's~st~.r~C" ~~~· ~C~e~nt~l'r~~
An~le of attack = 6° pre,surt•
Angle of atta<·k = 12•
Angle of attack = 18•
FIGURE 2-5. Effect of increasU., angle of attack.
The angle of attack changes as the aircraft's atti· tude changes. Since the angle of attack has a great deal to do with determining lift, it is given primary consideration when designing airfoils. In a properly designed airfoil, the lift increases as the angle of attack is increased.
When the angle of attack is increased gradually toward a positive angle of attack, the lift component increases rapidly up to a certain point and then suddenly begins to drop off. During this action the drag component increases slowly at first and then rapidly as lift begins to drop off.
When the angle of attack increases to the angle of maximum lift, the burble point is reached. This is known as the critical angle. When the critical
angle is reached, the air ceases to flow smoothly over the top surface of the airfoil and begins to burble, or eddy. This mealis that air breaks away from the upper camber line of the wing. What was formerly the area of decreased pressure is now filled by this burbling air. When this occurs, the amount of lift drops and drag becomes excessive. The force of gravity exerts itself, and the nose of the aircraft drops. Thus we see that the burble point is the stalling angle.
As we have seen, the distribution of the pressure forces over the airfoil varies with the angle of attack. The application of the resultant force, that is, the center of pressure, varies correspondingly. As this angle in~ the center of pressure moves forward; and as the angle decreases, the center of pressure moves back. The unstable travel of the center of pressure is characteristic of practically all airfoils.
Angle of Incidence
The acute angle which the wing chord makes with the longitudinal axis of the aircraft is called the angle of incidence (figure 2-6), or the angle of wing setting. The angle of incidence in most cases is a fixed, built-in angle. When the leading edge of the wing is higher than the trailing edge, the angle of incidence is said to be positive. The angle of incidence is negative when the leading edge is lower tlian the trailing edge of the wing.
Longitudinal
axis a';
Angle of incidence
F!GtJD 2-6. Angle of incidence.
Wing Area
Chord line
of wing
Wing area is measured in square feet and includes the part blanked out by the fuselage. Wing area is adequately described as the area of the shadow cast by the wing at high noon. Tests show that lift and drag forces acting on ·a \ring are roughly proportional to the wing area. This means that if the wing area is doubled, all other variables remaining the same, the lift and drag created by the
32
wing is doubled. If the area is tripled, lift and drag are tripled.
Shape of the Airfoil
The shape of the airfoil determines the amount of turbulence or skin friction that it will produce. The shape of a wing consequently affects the efficiency of the wing.
Airfoil section properties differ from wing or aircraft properties because of the effect of the wing planform. A wing may have various airfoil sections from root to tip, with taper, twist, and sweepback. The resulting aerodynamic properties of the wing are determined by the action of each section along the span.
Turbulence and skin friction are controlled mainly by the fineness ratio, which is defined as the ratio of the chord of the airfoil to the maximum thickness. If the wing has a high fineness ratio, it is a very thin wing. A thick wing has a low fineness ratio. A wing with a high fineness ratio produces a large amount of skin friction. A wing with a low fineness ratio produces a large amount of turbulence. The best wing is a compromise between these two extremes to hold both turbulence and skin friction to a minimum.
Continue reading ↓ 120 of 1993 passages shown