Radar Vectors
Advisory Circular Current Issued Jul 29, 2026 AFS-300 196 pages Copy saved Nov 18, 2026

AC 43.13-2C Acceptable Methods, Techniques, and Practices – Aircraft Alterations

This AC contains methods, techniques, and practices acceptable to the Administrator for the inspection and alteration on nonpressurized areas of civil aircraft of 12,500 pounds gross weight or less. This data generally pertains to minor alterations. However, the alteration data herein may be used as approved data for major alterations when the AC chapter, page, and paragraph are listed in block 8 of Federal Aviation Administration (FAA) Form 337, Major Repair and Alteration (Airframe, Powerplant, Propeller, or Appliance), when the user has determined that it is appropriate to the product being altered, directly applicable to the alteration being made, and not contrary to the manufacturer’s data. This AC contains information pertinent to Title 14 of the Code of Federal Regulations (14 CFR) § 43.13.

Official source ↗ Open PDF

U.S. Department of Transportation Federal Aviation Administration

Advisory Circular

Subject: Acceptable Methods, Techniques,

and Practices – Aircraft Alterations

Date: 7/29/26 AC No: 43.13-2C Initiated by: AFS-300 Change:

This advisory circular (AC) contains methods, techniques, and practices acceptable to the Administrator for the inspection and alteration on nonpressurized areas of civil aircraft of 12,500 pounds gross weight or less. This AC is for use by mechanics, repair stations, and other certificated entities.

Robert H. Reckert for Hugh Thomas Executive Director, Flight Standards Service

ii

CONTENTS Paragraph Page

Chapter 1. General … 1-1

1.1 Purpose of This Advisory Circular (AC) … 1-1

1.2 Audience … 1-1

1.3 Where You Can Find This AC … 1-1

1.4 What This AC Cancels … 1-1

1.5 Reference … 1-1

1.6 AC Feedback Form … 1-2

Chapter 2. Structural Data … 2-1

2.1 General … 2-1

2.2 Structural Design Process … 2-1

2.3 Types of Loads and Stresses … 2-1

2.4 Static Loads … 2-2

2.5 Structural Sizing and Analysis … 2-3

2.6 Static Tests … 2-4

2.7 Materials and Workmanship … 2-5

2.8 Material Strength Properties and Design Values … 2-5

2.9 Fasteners … 2-6

2.10 Protection of Structure … 2-6

2.11 Accessibility … 2-7

2.12 Effects on Weight and Balance (W&B) … 2-7

2.13 Effects on Safe Operation … 2-7

2.14 Controls and Indicators … 2-7

2.15 Placarding … 2-7

Chapter 3. Communication, Navigation, and Emergency Locator Transmitter System Installations … 3-1

3.1 Purpose … 3-1

3.2 Hazards and Warnings … 3-1

3.3 Considerations When Installing Avionics Equipment … 3-2

3.4 Instrument Panel Mounting … 3-4

3.5 Other Mounting Areas … 3-5

iii

3.6 Fabrication of Supporting Brackets for Attachment to a Structure Other Than Flooring … 3-7

3.7 Reinforcement of the Supporting Structure … 3-8

3.8 Electrical Requirements … 3-11

3.9 Electrical Load Analysis Procedure … 3-13

3.10 Electromagnetic Compatibility (EMC) … 3-13

3.11 Functional Hazard Assessment (FHA) … 3-16

Chapter 4. Antenna Installation … 4-1

4.1 Purpose … 4-1

4.2 Hazards and Warnings … 4-1

4.3 Additional References … 4-1

4.4 Structural Support … 4-1

4.5 Physical Interference … 4-2

4.6 Antenna Selection … 4-3

4.7 Antenna Location … 4-3

4.8 Antenna Bonding … 4-4

4.9 Electromagnetic Interference (EMI) … 4-5

4.10 Mechanical Installation … 4-5

4.11 Ground Plane Requirement (Wood/Fabric and Composite Aircraft) … 4-6

4.12 Antenna Feed Line Balun … 4-8

4.13 Antenna Repair … 4-10

Chapter 5. Anticollision and Supplementary Light Installation … 5-1

5.1 Purpose … 5-1

5.2 Hazards and Warnings … 5-1

5.3 Regulations and Other References … 5-1

5.4 Operational Considerations: Crew Vision … 5-2

5.5 Installation Considerations … 5-2

5.6 Markings and Placards … 5-2

5.7 Electrical Installation … 5-2

5.8 Alteration of Structure … 5-3

Chapter 6. Ski Installations … 6-1

6.1 Purpose … 6-1

iv

6.2 Hazards and Warnings … 6-1

6.3 Additional References (current editions) … 6-1

6.4 Installation Considerations … 6-1

6.5 Fabrication and Installation … 6-3

6.6 Rigging of Skis … 6-7

6.7 Documentation … 6-11

6.8 Flight and Handling Operational Checks … 6-12

6.9 Maintenance (Including Inspection) … 6-12

Chapter 7. Oxygen System Installations in Nonpressurized Aircraft … 7-1

Section 1. General … 7-1

7.1 Purpose … 7-1

7.2 Hazards and Warnings to Consider When Installing an Oxygen System … 7-1

7.3 Additional References (current editions) … 7-1

Section 2. Installation of the Oxygen System … 7-2

7.4 System Requirements … 7-2

7.5 Installation and Design Considerations … 7-4

7.6 Equipment Location and Mounting … 7-6

7.7 Thread Compound … 7-6

7.8 Functional Test … 7-6

7.9 Operating Instructions … 7-8

Section 3. Airworthiness Compliance Check Sheet: Oxygen System Installation in Unpressurized Aircraft … 7-12

7.10 General … 7-12

7.11 Applicable Federal Aviation Regulations … 7-12

7.12 Structural Requirements … 7-12

7.13 Hazards to the Aircraft or its Occupants … 7-12

7.14 Operating Aspects … 7-12

7.15 Detail Design Standards … 7-13

7.16 Instructions for Continued Airworthiness (ICA) … 7-13

7.17 Recordkeeping … 7-14

v

Chapter 8. Rotorcraft External-Load Device Installations, Cargo Slings, and External Racks ... 8-1

Section 1. General … 8-1

8.1 Purpose … 8-1

8.2 Hazards and Warnings … 8-1

8.3 References … 8-1

8.4 Installation Considerations … 8-1

8.5 Fabrication and Installation … 8-2

Section 2. Cargo Racks … 8-11

8.6 General … 8-11

8.7 Fabrication of Cargo Racks … 8-11

8.8 Static Test … 8-11

8.9 Supplemental Flight Information … 8-11

Chapter 9. Glider and Banner Tow-Hitch Installations … 9-1

9.1 Purpose … 9-1

9.2 Hazards and Warnings … 9-1

9.3 References … 9-1

9.4 Installation Considerations … 9-1

9.5 Fabrication and Installation Procedures … 9-1

9.6 Structural Testing … 9-3

9.7 Angles of Tow … 9-3

9.8 Placards … 9-4

9.9 Installation Procedures―Types of Hitches … 9-4

9.10 Tow Release Mechanism … 9-6

Chapter 10. Shoulder Harness Installations … 10-1

Section 1. General … 10-1

10.1 Purpose … 10-1

10.2 Hazards and Warnings … 10-1

10.3 Additional References … 10-1

10.4 Installation Methods … 10-1

10.5 Restraint System Configurations … 10-3

10.6 Advantages of Different Configurations … 10-3

vi

10.7 Manufacturing Standards … 10-4

10.8 Compliance With Standards … 10-4

10.9 Materials … 10-5

10.10 Parts Produced by Owners/Others … 10-6

Section 2. Geometry and Attachment … 10-8

10.11 General … 10-8

10.12 Mounting Configurations … 10-8

10.13 Belt Length … 10-8

10.14 Attachment Geometry … 10-8

10.15 Area and Angle Deviations … 10-15

10.16 Structural Attachment … 10-15

Section 3. Static Strength and Testing … 10-21

10.17 Proof of Compliance … 10-21

10.18 Load and Distribution―Airplanes … 10-21

10.19 Load and Distribution―Normal Category Helicopters … 10-22

10.20 Demonstrating Static Loads … 10-22

Section 4. Installation and Inspection Checklists … 10-26

10.21 General … 10-26

Chapter 11. Aircraft Battery Installations … 11-1

Section 1. General … 11-1

11.1 Purpose … 11-1

11.2 Hazards and Warnings: Handling Precautions … 11-1

11.3 Additional References (current editions) … 11-1

11.4 Location Requirements … 11-1

11.5 Aircraft Storage Battery Design and Installation … 11-2

11.6 Duplication of the Manufacturer’s Installation … 11-3

11.7 Other Installations … 11-3

11.8 Delivery Inspection … 11-3

11.9 Battery Installation and Removal … 11-4

Section 2. Lead-Acid Battery Installations … 11-6

11.10 General … 11-6

vii

11.11 Battery Box … 11-6

11.12 Securing the Battery … 11-6

11.13 Sump Jar … 11-6

11.14 Venting … 11-7

11.15 Drains … 11-8

11.16 Electrical Installation … 11-8

11.17 Quick Disconnect … 11-10

11.18 Weight and Balance (W&B) … 11-10

Section 3. Nickel-Cadmium Battery Installations … 11-11

11.19 General … 11-11

11.20 Electrical Analysis … 11-11

11.21 Maintenance Considerations … 11-11

11.22 Structural Requirements … 11-11

11.23 Isolation of Battery Case … 11-12

11.24 Ventilation … 11-12

11.25 Preinstallation Requirements … 11-12

11.26 Nickel-Cadmium Battery Installation … 11-13

11.27 Securing the Battery … 11-13

11.28 Quick Disconnect … 11-13

11.29 Voltage and Current Regulation … 11-14

11.30 Weight and Balance (W&B) … 11-14

Section 4. Battery Installation Checklist … 11-15

11.31 Structural Requirements … 11-15

11.32 Hazards to the Aircraft and its Occupants … 11-16

11.33 Operating Aspects … 11-16

11.34 Detail Design Standards … 11-16

11.35 Recordkeeping … 11-17

Section 5. Instructions for Continued Airworthiness … 11-18

11.36 Lead-Acid Batteries … 11-18

11.37 Nickel-Cadmium Batteries … 11-19

viii

Chapter 12. Adding or Relocating Instruments … 12-1

12.1 Purpose … 12-1

12.2 Hazards and Warnings … 12-1

12.3 Additional References … 12-1

12.4 Preparation … 12-1

12.5 Installation … 12-3

12.6 Testing, Marking, and Placarding … 12-9

12.7 Electronic Display Instrument Systems or Electronic Display Indicators … 12-11

12.8 Environmental Conditions … 12-12

Chapter 13. Cargo Tiedown Device Installations … 13-1

13.1 Purpose … 13-1

13.2 Hazards and Warnings … 13-1

13.3 Installation Considerations … 13-1

13.4 Fabrication and Installation … 13-1

13.5 Operating Limitations, Loading Instructions, and Placards … 13-9

13.6 Airworthiness Compliance Check Sheet: Cargo Tiedown Device Installations … 13-9

Chapter 14. Larger Tire Installations … 14-1

14.1 Purpose … 14-1

14.2 Hazards and Warnings … 14-1

14.3 Additional Reference (current editions) … 14-1

14.4 Installation Considerations … 14-2

14.5 Flight and Ground Handling Operational Checks … 14-4

14.6 Testing the Modification … 14-6

14.7 Maintenance (Including Inspection) … 14-7

14.8 Interchanging of Skis and Wheels … 14-9

14.9 Documentation … 14-9

14.10 Summary of Considerations for Approval of Larger Tire Installation (may be used as a job aid) … 14-9

ix

List of Figures

Figure 2-1. Bending of a Beam … 2-2

Figure 2-2. Typical Load … 2-3

Figure 2-3. Hypothetical of Determining Static Test Loads … 2-8

Figure 3-1. Force Diagram Normal-Utility Category … 3-3

Figure 3-2. Typical Fabricated Panel Mounting … 3-3

Figure 3-3. Typical Layouts … 3-4

Figure 3-4. Typical Shock-Mounted Base (Wood or Composition Flooring) … 3-6

Figure 3-5. Typical Shock-Mounted Base (Metal Flooring) … 3-6

Figure 3-6. Typical Rigid Base Plate Mount … 3-7

Figure 3-7. Typical Underseat Installation … 3-8

Figure 3-8. Typical Remote Unit Mounting Base-Vertical or Horizontal Other Than

Structure to Floor … 3-9

Figure 3-9. Typical Shelf Installation … 3-10

Figure 3-10. Typical Attachment of Support Structure to Tubular Frame Other Than

Structure to Floor … 3-11

Figure 4-1. Antenna Mount With Saddle … 4-2

Figure 4-2. Antenna Ground Plane for Nonconductive Mount … 4-7

Figure 4-3. One Means to Provide Adequate Antenna Bonding Through a

Composite Airframe … 4-7

Figure 4-4. Use Bushings for All Screws … 4-8

Figure 4-5. Typical Dipole Antenna Assembly … 4-9

Figure 4-6. Typical VOR Balun … 4-10

Figure 4-7. ADF Loop … 4-11

Figure 4-8. ADF Combined Sense Loop … 4-11

Figure 4-9. Communications (COM) Whip … 4-11

Figure 4-10. COM Whip Bent … 4-12

Figure 4-11. Emergency Locator Transmitter … 4-12

Figure 4-12. Global Positioning System … 4-12

Figure 4-13. Glideslope … 4-13

Figure 4-14. Marker … 4-13

Figure 4-15. Combined COM/VOR … 4-13

Figure 4-16. VOR Rabbit Ear … 4-14

x

Figure 4-17. VOR Blades … 4-14

Figure 4-18. Transponder/DME Probe … 4-15

Figure 4-19. DME/Transponder Blade … 4-15

Figure 5-1. Typical Anticollision or Supplementary Light Installation in a Skin

Panel (Unpressurized) … 5-3

Figure 5-2. Typical Anticollision or Supplementary Light Installation Involving a Cut

Stringer (Unpressurized) … 5-4

Figure 5-3. Typical Anticollision or Supplementary Light Installation in a Fin Tip … 5-5

Figure 6-1. Typical Hub Installation … 6-3

Figure 6-2. Typical Ski Installation … 6-4

Figure 6-3. Typical Fuselage Fittings … 6-6

Figure 6-4. Main Ski at Maximum Positive Incidence (Check Cable Taut) … 6-7

Figure 6-5. Main Ski at Maximum Negative Incidence (Safety Cable Taut) … 6-8

Figure 6-6. Main Ski Incidence Angles … 6-8

Figure 6-7. Typical Nose Ski Installation … 6-10

Figure 6-8. Typical Tail Ski Installation … 6-11

Figure 7-1. Typical Floor Mounting … 7-9

Figure 7-2. Typical Baggage Compartment Mounting … 7-10

Figure 7-3. Typical Oxygen Installation in Light Twin Aircraft … 7-11

Figure 8-1. Location of Cargo Release in Relation to the Rotorcraft’s Center of Gravity … 8-2

Figure 8-2. Typical Cargo Sling Wiring Diagram … 8-5

Figure 8-3. Typical Cargo Sling Installation No. 1 … 8-6

Figure 8-4. Typical Cargo Sling Installation No. 1 (Showing Fuselage Attachment Fitting) … 8-7

Figure 8-5. Typical Cargo Sling Installation No. 1 (Showing Fore Aft Limiting Stops) … 8-8

Figure 8-6. Typical Cargo Sling Installation No. 2 (Cargo Hook Attached Directly to

Underside of Fuselage) … 8-8

Figure 8-7. Typical Cargo Sling Installation No. 3 (4-Leg, Cable Suspended) … 8-9

Figure 8-8. Typical Cargo Sling Installation No. 3 (Showing Cable Sling Leg Attachment

to Landing Gear Crosstube Fitting) … 8-9

Figure 8-9. Typical Cargo Sling Installation No. 3 (Showing Cargo Sling in

Stowed Position) … 8-10

Figure 8-10. Typical Cargo Rack Installation No. 1 … 8-11

Figure 8-11. Typical Cargo Rack Installation No. 1 (Showing Attachment Detail) … 8-12

Figure 8-12. Typical Cargo Rack Installation No. 2 … 8-12

xi

Figure 8-13. Typical Cargo Rack Installation No. 2 (Showing Rack Partially Installed) … 8-13

Figure 8-14. Typical Cargo Rack Installation No. 3 … 8-13

Figure 9-1. Glider Tow Angle … 9-2

Figure 9-2. Banner Tow Angle … 9-2

Figure 9-3. Typical Tow-Hitch Release Handle … 9-7

Figure 9-4. Tricycle Gear Aircraft … 9-8

Figure 9-5. Conventional Gear Aircraft—Leaf Spring Type Tailwheel … 9-8

Figure 9-6. Conventional Gear Aircraft—Shock Strut Type Tailwheel … 9-9

Figure 9-7. Conventional Gear Aircraft—Tubular Spring Type Tailwheel … 9-9

Figure 9-8. Typical TOST Hitch … 9-10

Figure 9-9. TOST Double Tow Rings … 9-10

Figure 9-10. Schweizer Type Hitch … 9-11

Figure 9-11. Typical Multiple Hitch for Banner Tow … 9-12

Figure 9-12. Typical TOST Mount for Tricycle Gear Aircraft … 9-12

Figure 9-13. Typical TOST Conventional Leaf Spring Mount … 9-13

Figure 10-1. Major Versus Minor Alterations … 10-3

Figure 10-2. The Three-Point Single Harness Positioning … 10-10

Figure 10-3. Side Mounted Single Diagonal Type Harness … 10-11

Figure 10-4. Acceptable Harness Mounting Areas … 10-11

Figure 10-5. Undesirable Horizontal Harness Positioning … 10-12

Figure 10-6. Undesirable Vertical Harness Positioning … 10-12

Figure 10-7. Ceiling Mounted Inertia Reel―Double Over-the-Shoulder Type Harness … 10-13

Figure 10-8. The Four-Point Independent Harnesses Positioning … 10-13

Figure 10-9. The Five-Point Harness Positioning … 10-14

Figure 10-10. “Y” Type Retractor Positioning … 10-14

Figure 10-11. Floor Mounted Inertia Reel―Double Over-the-Shoulder Type Harness … 10-16

Figure 10-12. Typical Floor Mounted Inertia Reel Installation … 10-16

Figure 10-13. Typical Seat Mounted Inertia Reel Installation … 10-17

Figure 10-14. Typical Wing Carry-Through Installation … 10-18

Figure 10-15. Typical Hat Section Reinforcement Installation … 10-18

Figure 10-16. Typical Bulkhead Reinforcement Installation … 10-19

Figure 10-17. Typical Stringer Section Reinforcement Installation … 10-19

Figure 10-18. Typical Localized Stringer Section Reinforcement Installation … 10-20

xii

Figure 10-19. Typical Attachments to Tubular Members … 10-20

Figure 10-20. Vertical Angle … 10-25

Figure 10-21. Horizontal Angle … 10-25

Figure 11-1. Typical Battery Installation in the Aircraft … 11-5

Figure 11-2. Typical Battery Installation With Sump Jar … 11-7

Figure 11-3. Battery Ventilation System … 11-8

Figure 11-4. Typical Battery Cutoff and Generator Alternator Control Circuit … 11-10

Figure 12-1. The Basic “T” Visual Meteorological Conditions (VMC)

Instrument Configuration … 12-2

Figure 12-2. Pressure Drop Data for Smooth Tubing … 12-7

Figure 13-1. Extruded Track, Anchor Plates, and Associated Fittings … 13-3

Figure 13-2. Miscellaneous Litter, Berth, and Cargo Tiedown Fittings … 13-4

Figure 13-3. Typical Attachment of Fittings to Honeycomb Structures … 13-5

Figure 13-3. Typical Attachment of Fittings to Honeycomb Structures – Continued … 13-6

Figure 13-4. Installation of Underfloor Support for Extruded Track … 13-6

Figure 13-5. Typical Cargo Tiedown Straps and Cargo Nets … 13-7

Figure 13-6. Example of Allowable Cargo Loading Diagram … 13-12

Figure 14-1. Diagram of Axle Height Measurement … 14-3

Figure 14-2. Typical Main Landing Gear Spring Strut and Axle Assembly … 14-8

List of Tables

Table 2-1. Ultimate Load Factors … 2-3

Table 2-2. Sample Load Factors … 2-4

Table 3-1. Typical Compass Calibration Card … 3-5

Table 3-2. Relationship Probabilities and Severity of Failure Conditions … 3-14

Table 3-3. Commonly Used Radio Frequencies on Aircraft … 3-15

Table 3-4. Aircraft Electrical and Electronic Systems … 3-16

Table 4-1. Wavelength in Feet = 984/Frequency in Megahertz (MHz) … 4-6

Table 6-1. Recommended Minimum Cable and Shock Cord Sizes … 6-5

Table 6-2. Approximate Main Ski Tension Forces … 6-9

Table 7-1. Typical Oxygen Duration Table … 7-8

Table 8-1. Cable Load Table … 8-3

Table 9-1. Representative Steel Cable Qualities … 9-7

Table 10-1. Static Test Requirements … 10-24

xiii

Table 10-2. Calculated 1/Cosine Values … 10-24

Table 12-1. CFM/Vacuum Values … 12-5

Table 12-2. Instrument Air Consumption for Example Vacuum-Driven Autopilot and

Instrument Installations … 12-5

Table 12-3. Equivalent Straight Tube Line Drops for Each 90-Degree Elbow Installed

in Any Given System (By O.D.) … 12-6

Table 12-4. Differential Pressure Across the Instrument Inlet and Outlet of the Example

Instrument Packages … 12-6

CHAPTER 1. GENERAL › 1.5 Reference.

CHAPTER 1. GENERAL

1.1 Purpose of This Advisory Circular (AC). This AC contains methods, techniques, and practices acceptable to the Administrator for the inspection and alteration on nonpressurized areas of civil aircraft of 12,500 pounds gross weight or less. This data generally pertains to minor alterations. However, the alteration data herein may be used as approved data for major alterations when the AC chapter, page, and paragraph are listed in block 8 of Federal Aviation Administration (FAA) Form 337, Major Repair and Alteration (Airframe, Powerplant, Propeller, or Appliance), when the user has determined that it is appropriate to the product being altered, directly applicable to the alteration being made, and not contrary to the manufacturer’s data. This AC contains information pertinent to Title 14 of the Code of Federal Regulations (14 CFR) § 43.13.

Note: This is a guidance document. Its content is not legally binding in its own right and will not be relied upon by the Department as a separate basis for affirmative enforcement action or other administrative penalty. Conformity with the guidance document is voluntary only. Nonconformity will not affect rights and obligations under existing statutes and regulations.

Note: The methods, techniques, and practices in this AC are an acceptable means of compliance with the regulation, but they are not the only means of compliance. If persons performing maintenance, alteration, or preventive maintenance undertake another means of compliance, it must be acceptable to the FAA. References to an established standard or publication support the acceptability of alternative methods, techniques, and practices.

1.2 Audience. This AC is for use by mechanics, repair stations, and other certificated entities.

1.3 Where You Can Find This AC. You can find this AC on the FAA’s website at https://www.faa.gov/regulations_policies/advisory_circulars and the Dynamic Regulatory System (DRS) at https://drs.faa.gov.

1.4 What This AC Cancels. AC 43.13-2B, Acceptable Methods, Techniques, and Practices – Aircraft Alterations, dated March 3, 2008, is canceled.

1.5 Reference. Title 14 CFR § 43.13(a) states that each person performing maintenance, alteration, or preventive maintenance on an aircraft, engine, propeller, or appliance must use the methods, techniques, and practices prescribed in the current manufacturer’s maintenance manual, the instructions for continued airworthiness (ICA) prepared by its manufacturer, or other methods, techniques, or practices acceptable to the Administrator except as noted in 14 CFR § 43.16. FAA inspectors are prepared to answer questions that may arise in this regard. Persons engaged in the inspection and alteration of civil aircraft should be familiar with 14 CFR part 43 and 14 CFR part 65 subparts A, D, and E and applicable airworthiness requirements under which the aircraft was type certificated.

Note: Part 23 Amendment 23-63 and prior 14 CFR part 23 (prescriptive) regulations referenced in this AC contain sufficiently detailed language to allow

CHAPTER 1. GENERAL › 1.6 AC Feedback Form.

compliance directly with each section (regulation) when applied to traditional designs that were prevalent at the time the regulations were written. These legacy prescriptive regulations are not sufficient nor appropriate for some modern designs. To show compliance with the new “performance-based rules” (Amendment 23-64, Implementation Procedures Guide, and subsequent), the applicant must choose an accepted means of compliance, per 14 CFR § 23.2010. For more information, refer to Amendment 23-64 and AC 23.2010, FAA Accepted Means of Compliance Process for 14 CFR Part 23.

1.6 AC Feedback Form. For your convenience, the AC Feedback Form is the last page of this AC. Note any deficiencies found, clarifications needed, or suggested improvements regarding the contents of this AC on the Feedback Form.

2.3 Types of Loads and Stresses. › 2.3.8 “Bending” is a combination of two forces, compression, and tension.

CHAPTER 2. STRUCTURAL DATA

2.1 General. Structural integrity is a major factor in aircraft design and construction. Addition or removal of equipment involving changes in weight could affect the structural integrity, weight, balance, flight characteristics, reliability, or performance of an aircraft. This chapter is generic in nature and meant to assist the aviation maintenance technician in determining structural integrity. It is not meant to circumvent utilizing an FAA engineer or the responsible Aircraft Certification Service office when necessary.

2.2 Structural Design Process. Structural design processes follow these steps:

• Determine the overall load factors.

• Estimate the resulting loads.

• Distribute these loads over the aircraft.

• Determine the material, size, and shape of the part.

• Calculate the resulting stresses in the part.

• Compare these stresses with the maximum allowable for the material used.

• Resize the part as necessary.

2.3 Types of Loads and Stresses.

2.3.1 “Limit load factors” are the maximum load factors that may be expected during service (the maneuvering, gust, or ground load factors established by the manufacturer for type certification).

2.3.2 Aircraft parts may be formed out of different types of material and joined together. Each of those parts carries a load, and the fastener that brings these parts together has to carry the load from one part to the other.

2.3.3 Every aircraft is subject to different types of structural stress. Stress acts on an aircraft whether it is on the ground or in flight. Stress is defined as a load applied to a unit area of material.

2.3.4 “Tension” is a force acting against another force that is trying to pull something apart.

2.3.5 “Compression” is a squeezing or crushing force that tries to make parts smaller.

2.3.6 “Torsion” is a twisting force.

2.3.7 “Shear stress” is when one piece of material slides over another.

2.3.8 “Bending” is a combination of two forces, compression, and tension. During bending stress, the material on the inside of the bend is compressed and the outside material is stretched in tension.

Figure 2-1. Bending of a Beam

2.3.9 An aircraft structure in flight is subjected to variable stresses due to the varying loads that may be imposed. The designer’s problem involves anticipating the possible stresses that the structure will have to endure and build the structure strong enough to withstand these stresses.

2.4 Static Loads. › 2.4.4 “Critical static test load factors” are the greater of the…

2.4 Static Loads. “Static loads” are loads that do not undergo change in magnitude or direction during a measurement procedure. Load factors are defined as follows:

2.4.1 “Limit load factors” are the maximum load factors that may be expected during service (the maneuvering, gust, or ground load factors established for type certification).

2.4.2 “Ultimate load factors” are the limit load factors multiplied by a prescribed factor of safety. Certain loads, such as the minimum ultimate inertia forces prescribed for emergency landing conditions, are given directly in terms of ultimate loads.

2.4.3 “Static test load factors” are the ultimate loads multiplied by the casting, fitting, bearing, and/or other special factors, when applicable. Where no special factors apply, the static test loads are equal to the ultimate loads.

2.4.4 “Critical static test load factors” are the greater of the maneuvering, gust, ground, and inertia load static test load factors for each direction (up, down, starboard, port, fore, and aft).

2.5 Structural Sizing and Analysis. › 2.5.1 Static tests using the load factors in Table 2-1 are acceptable…

Figure 2-2. Typical Load

2.5 Structural Sizing and Analysis. Design and size your load structures, including wing spars, wing attach fittings, stabilizers, landing gear struts, etc.

2.5.1 Static tests using the load factors in Table 2-1 are acceptable for equipment installations. The alteration needs to comply with the limit load factors as required by the aircraft’s certification basis.

Table 2-1. Ultimate Load Factors

Direction of

Force Applied

Normal-Utility

Occupant 14 CFR Part 23 (CAR 3)

Acrobatic Occupant 14 CFR Part 23 (CAR 3)

Items of Mass Within the Cabin

14 CFR Part 23 (CAR 3)

Rotorcraft Occupant

and Items of Mass

Within the Cabin

14 CFR Part 27 (CAR 6)

Sideward 1.5g 1.5g 4.5g 8.0g

Upward 3.0g 4.5g 3.0g 4.0g

Forward 9.0g 9.0g 18.0g 16.0g

Downward 6.6g 9.0g - 20.0g

Rearward - - - 1.5g

Note 1: When equipment mounting is located externally to one side, or forward of occupants, a forward load factor of 2.0g is sufficient.

Note 2: Due to differences among various aircraft designs in flight and ground load factors, contact the aircraft manufacturer for the load factors required for a given model and location. In lieu of specific information, the factors used for the 14 CFR part 23 utility category are acceptable for aircraft that never exceed the speed of 250 knots and the factors used for 14 CFR part 23 acrobatic category.

2.6 Static Tests. › 2.6.3 Determine the critical ultimate load factors for the sideward,…

2.5.2 Table 2-2 is an example of determining the static test loads for a 7-pound piece of equipment to be installed in a utility category aircraft (14 CFR part 23).

Table 2-2. Sample Load Factors

Load Factors (From the Above Table)

Static Test Loads (Load Factor x 7 Pounds)

Sideward 1.5g 10.5 pounds

Upward 3.0g 21.0 pounds

Downward 6.6g 46.2 pounds

Forward 9.0g 63.0 pounds

2.5.3 When an additional load is to be added to a structure already supporting previously installed equipment, determine the capability of the structure to support the total load (previous load plus added load). If the additional load requires access to applicable design data or the capability to reverse engineer the installation, further assistance may be required from FAA engineering, the responsible Aircraft Certification Service office, or an appropriately rated Designated Engineering Representative (DER).

2.6 Static Tests.

CAUTION: The aircraft or equipment, or both, can be damaged in applying static loads, particularly if a careless or improper procedure is used. It is recommended, whenever practicable, that static testing be conducted on a duplicate installation in a jig or mockup that simulates the related aircraft structure. Static test loads may exceed the yield limits of the assemblies being substantiated and can result in partially sheared fasteners, elongated holes, or other damage that may not be visible unless the structure is disassembled. If the structure is materially weakened during testing, it may fail at a later date. Riveted sheet metal and composite laminate construction methods especially do not lend themselves to easy detection of such damage. To conduct static tests:

2.6.1 Determine the weight and center of gravity (CG) position of the equipment item.

2.6.2 Install the attachment in the aircraft or, preferably, in a jig using the applicable static test load factors.

2.6.3 Determine the critical ultimate load factors for the sideward, upward, downward, and forward directions. A hypothetical, which follows steps 1 through 4 below, pertains to the example in Figure 2-3, Hypothetical of Determining Static Test Loads.

1. Convert the gust, maneuvering, and ground load factors obtained from the manufacturer, FAA engineer, or DER to determine the ultimate load factors. Unless otherwise specified in the airworthiness standards applicable to the aircraft, ultimate

CHAPTER 2. STRUCTURAL DATA › 2.8 Material Strength Properties and Design Values.

load factors are limit load factors multiplied by a 1.5 safety factor (see Figure 2-3, columns 1, 2, and 3 for items A, B, and C).

2. Determine the ultimate inertia load forces for the emergency landing conditions as prescribed in the applicable airworthiness standards. (See Figure 2-3, items D and E, column 3.)

3. Determine what additional load factors are applicable to the specific seat, litter, berth, or cargo tiedown device installation. The ultimate load factors are then multiplied by these factors to obtain the static test factors.

4. Select the highest static test load factors obtained in steps 1, 2, and/or 3 for each direction (sideward, upward, downward, and forward). These factors are the critical static test load factors used to compute the static test load (see Figure 2-3, column 6).

2.6.4 Apply a load at the CG position by any suitable means to demonstrate that the attachment and structure are capable of supporting the required loads. When no damage or permanent deformation occurs after 3 seconds of applied static load, the structure and attachments are acceptable. Should permanent deformation occur after 3 seconds, modifications or reinforcements to the affected structure are required. Additional load testing is not necessary.

2.6.5 Static tests may need to be reviewed by an FAA engineer so that appropriate limitations, procedures, checks, and balances may be applied to mitigate any risks.

2.7 Materials and Workmanship. Use materials conforming to an accepted government or industry standard such as Army/Navy and Air Force/Navy (AN) National Aerospace Standards (NAS), Technical Standard Orders (TSO), or Military Specifications (MIL-SPEC).

2.7.1 Suitability and durability of materials used for parts, the failure of which could adversely affect safety, must:

• Be established by experience or tests;

• Meet approved specifications that ensure the strength, and other properties, assumed in the design data; and

• Take into account the effects of environmental conditions, such as temperature and humidity, expected in service.

2.7.2 Workmanship must be of a high standard.

2.8 Material Strength Properties and Design Values. Material strength properties must be based on enough tests of material meeting specifications to establish design values on a statistical basis, such as Metallic Materials Properties Development and Standardization (MMPDS), available at https://www.mmpds.org/. Design values must be chosen to minimize the probability of structural failure due to material variability. Except as provided in paragraph 2.8.5 below, compliance with this paragraph must be shown by selecting design values that ensure material strength with the following probabilities:

2.10 Protection of Structure. › 2.10.2 Have adequate provisions for ventilation and drainage.

2.8.1 Where applied loads are eventually distributed through a single member within an assembly, the failure of which would result in loss of structural integrity of the component―99 percent probability with 95 percent confidence.

2.8.2 For redundant structure, in which the failure of individual elements would result in applied loads being safely distributed to other load carrying members―90 percent probability with 95 percent confidence.

2.8.3 The effects of temperature on allowable stresses used for design in an essential component or structure must be considered where thermal effects are significant under normal operating conditions.

2.8.4 The design of the structure must minimize the probability of catastrophic fatigue failure, particularly at points of stress concentration.

2.8.5 Design values greater than the guaranteed minimums required by paragraph 2.8 may be used where only guaranteed minimum values are normally allowed (e.g., if a “premium selection” of the material is made in which a specimen of each item is tested before use to determine if the actual strength properties of that particular item are equal or exceed those used in design).

2.9 Fasteners. Use hardware conforming to an accepted government or industry standard such as AN, NAS, TSO, or MIL-SPEC. Attach equipment in such a way that prevents loosening in service due to vibration.

2.9.1 Each removable fastener must incorporate two retaining devices in case one retaining device should fail during flight operations.

2.9.2 Fasteners and their locking devices must not be adversely affected by the environmental conditions associated with the particular installation.

2.9.3 No self-locking nut may be used on any bolt subject to rotation in operation unless a nonfriction locking device is used in addition to the self-locking device.

2.10 Protection of Structure. Provide protection against deterioration or loss of strength due to corrosion, abrasion, electrolytic action, or other causes. Each part of the structure must:

2.10.1 Be suitably protected against deterioration or loss of strength in service due to any cause, including:

• Weathering,

• Corrosion, and

• Abrasion.

2.10.2 Have adequate provisions for ventilation and drainage.

CHAPTER 2. STRUCTURAL DATA › 2.15 Placarding.

2.11 Accessibility. Provide adequate provisions to permit close examination of equipment or adjacent parts of the aircraft that regularly require, among other services, inspection, adjustment, and lubrication. For each part that requires maintenance, inspection, or other servicing, appropriate means must be incorporated into the aircraft design to allow such servicing to be accomplished.

2.12 Effects on Weight and Balance (W&B). Ensure that the altered aircraft can be operated within the weight and CG ranges listed in the FAA type certificate (TC), data sheet, or Aircraft Listing Aircraft Specification. When adding items of mass to the aircraft, the effect on the empty W&B should be considered and documented in the aircraft W&B. Determine that the altered aircraft will not exceed maximum gross weight. If applicable, correct the loading schedule to reflect the current loading procedure. Refer to AC 43.13-1, Acceptable Methods, Techniques, and Practices―Aircraft Inspection and Repair, for W&B computation procedures.

2.13 Effects on Safe Operation. Install equipment in a manner that will not interfere with or adversely affect the safe operation of the aircraft (controls, navigation equipment operation, etc.).

2.13.1 The factor of safety prescribed in 14 CFR § 23.303 must be multiplied by the highest pertinent special factors of safety prescribed in 14 CFR §§ 23.621 through 23.625 for each part of the structure where strength is:

• Uncertain,

• Likely to deteriorate in service before normal replacement, or

• Subject to appreciable variability because of uncertainties in manufacturing processes or inspection methods.

2.13.2 Unless otherwise provided, a factor of safety of 1.5 must be used.

2.14 Controls and Indicators. Locate and identify equipment controls and indicators so they can be operated and read from the appropriate crewmember position.

2.15 Placarding. Label equipment requiring identification and, if necessary, placard operational instructions. Amend W&B information as required. Any required placards installed or required by an alteration must be added to the “Limitations” section of the instructions for continued airworthiness (ICA) to ensure that maintenance personnel will know if a required placard is missing in future inspections.

Figure 2-3. Hypothetical of Determining Static Test Loads

Utility Category Aircraft (14 CFR Part 23)

Type of Load Direction

Load Factors

1 Limit

2 x Safety

3 = Ultimate

4 x Special

5 Static = Test

6 Critical Static

Test

A. Maneuvering Fwd (None) - - -

Down 6.2g 1.5 9.3g - 9.3g 9.3g

Side (None) - - - -

Up -3.8g 1.5 -5.7g - -5.7g 5.7g

Aft 1.0g 1.5 1.5g - 1.5g

B. Gust (= 30 FPS @ KVc)

*For locations aft of fuselage Sta. 73.85.

Fwd (None) - - - -

Down 6.0g 1.5 9.0g - 9.0g

Down* 6.4g 1.5 9.6g - 9.0g *9.6g

Side 1.6g 1.5 2.4g - 2.4g 2.4g

Up -2.8g 1.5 -4.2g - -4.2g

Aft (None) - - - -

C. Ground Fwd 6.6g 1.5 9.9g - 9.9g 9.9g

Down 4.0g 1.5 6.0g - 6.0g

D. Ultimate Inertia Forces for Emergency Landing Condition (14 CFR § 23.561). **For separate cargo compartments.

Fwd

Already Prescribed as Ultimate

9.0g - -

Fwd** 4.5g - - **4.5g

Down (None) - -

Side 1.5g - 1.5g

Up -3.0g - -3.0g

Aft (None) - -

Utility Category Aircraft (14 CFR Part 23)

Type of Load Direction

Load Factors

1 Limit

2 x Safety

3 = Ultimate

4 x Special

5 Static = Test

6 Critical Static

Test

E. Ultimate Inertia Forces for Emergency Landing Condition For Seat, Litter, and Berth Attachment to Aircraft Structure (14 CFR § 23.785).

Fwd

Already Prescribed as Ultimate

9.0g 1.33 12.0g 12.0g

Down (None) - -

Side 1.5g 1.33 2.0g

Up -3.0g 1.33 -4.0g

Aft (None) - -

Note: Asterisks (*) denote special load conditions for the situation shown.

3.2 Hazards and Warnings. › 3.2.7 Ensure that the capacity of the aircraft’s charging system is not…

CHAPTER 3. COMMUNICATION, NAVIGATION, AND EMERGENCY LOCATOR

TRANSMITTER SYSTEM INSTALLATIONS

3.1 Purpose. This chapter describes installation considerations and requirements for basic standalone, installations of communication, navigation, and emergency locator transmitter (ELT) equipment.

Note: Standalone installations do not depend on other systems or complex interfaces to function.

3.2 Hazards and Warnings.

3.2.1 When installing these systems, follow the aircraft and equipment manufacturers’ instructions, as appropriate. Practice a “clean as you go” philosophy, which entails maintaining cleanliness and order. Ensure that equipment and systems function properly and perform their intended function(s).

3.2.2 Alterations of aircraft that are performed to accommodate the installation of radio equipment must be evaluated for their impact on aircraft design and operation. Refer to AC 23.1309-1, System Safety Analysis and Assessment for Part 23 Airplanes, for additional information concerning the evaluation for equipment, systems, and installations in 14 CFR part 23 airplanes.

3.2.3 Frequently, an alteration to accommodate the installation of radio equipment will have little impact on the design or operation of an aircraft; however, all potential elements of impact must be considered. One approach is to evaluate each element independently.

3.2.4 Consider the impact when Weight and Balance (W&B) or structural load limits of an added system exceeds existing installations. Consider the impact when radio frequency, such as electromagnetic interference (EMI), High Intensity Radiated Fields (HIRF), or lightning, may negatively affect existing systems (e.g., accuracy of the magnetic compass).

3.2.5 When evaluating elements of impact, consider the before and after states. No further analysis of W&B may be required if an object of similar size and weight was previously installed in a location. If mounting attach points were previously substantiated to support a specific load and the same load or less is being installed, the previous analysis may be referenced.

Note: Data that is referenced must be available and reviewed.

3.2.6 When structures must be fabricated or reinforced, the standard practices approved for repairs, if applicable, may be employed. AC 43.13-1, Acceptable Methods, Techniques, and Practices—Aircraft Inspection and Repair, may provide structural design data for fabrication of mountings and attachments.

3.2.7 Ensure that the capacity of the aircraft’s charging system is not exceeded, including any required additional allowances.

3.3.2 Structural Consideration. Consider the following: › 3.3.2.1 Structural requirements of a mounting must be considered (see…

3.2.8 Care should be taken to ensure that cables or wires will not interfere with the aircraft’s flight, engine, or propeller controls.

3.2.9 When removing older radios, wiring, or power supplies and installing newer solid-state components, weigh the old equipment and perform a new W&B calculation. This is important since differences in the location and weight of equipment will shift the center of gravity (CG).

3.2.10 Refer to AC 43.13-1, Chapter 10, Weight and Balance, and FAA-H-8083-1, Aircraft Weight and Balance Handbook, for additional information on determining W&B.

3.3 Considerations When Installing Avionics Equipment. When installing radio equipment, use areas or locations designated by the airframe manufacturer and use factory-supplied brackets or racks. Follow the aircraft manufacturer’s installation instructions. When this information is not available, use locations in the aircraft of known load-carrying capabilities. Baggage compartments, cabins, or flight deck floors are good mounting platforms provided the floor attachments meet the strength requirements. Another method is to fabricate support racks, brackets, or shelves and attach them to the aircraft structure to provide a mounting that will withstand the inertia forces stipulated in Chapter 2, Structural Data.

3.3.1 General Considerations. Ensure the following:

3.3.1.1 There is appropriate air circulation to ensure proper cooling and dissipation of any heat generated or present. Consider the flammability characteristics of all associated elements.

3.3.1.2 There are appropriate clearances to prevent mechanical damage to other parts of the aircraft or from other parts of the aircraft.

3.3.1.3 There is protection provided to the component or article from any fluids or fumes that may be expected and that the component or article will not cause any fluids or fumes to be present that may result in damage to the aircraft or its occupants.

3.3.1.4 That any interference, environmental or operational, to an aircraft or any system of the aircraft is identified and minimized as to not affect airworthiness of the aircraft.

3.3.1.5 That flight characteristics of the aircraft are not altered unless appropriately identified and the changes are within the certified design limits.

3.3.2 Structural Consideration. Consider the following:

3.3.2.1 Structural requirements of a mounting must be considered (see Chapter 2).

3.3.2 Structural Consideration. Consider the following: › 3.3.2.5 Methods and practices described elsewhere in this AC and in AC…

Figure 3-1. Force Diagram Normal-Utility Category

3.3.2.2 Alterations that include making additional cutouts or enlargements of existing panel cutouts must be evaluated to maintain structural integrity. Some aircraft instrument panels are load bearing structures.

3.3.2.3 Loads must be determined to be within the structural design limits of the supports.

3.3.2.4 Instrument panels and other panels throughout the aircraft may be structural or nonstructural in design. Structural loads must be adequately transferred to primary airframe members.

3.3.2.5 Methods and practices described elsewhere in this AC and in AC 43.13-1 may be employed for the fabrication of attachments and structure.

Figure 3-2. Typical Fabricated Panel Mounting

3.4 Instrument Panel Mounting. › 3.4.5 Existing Factory Fasteners.

Figure 3-3. Typical Layouts

Typical layout of an older aircraft

Typical layout of a newer aircraft

3.3.2.6 Existing structures may be reinforced or strengthened using methods described in AC 43.13-1.

3.4 Instrument Panel Mounting. This paragraph is supplemented by AC 43.13-1, Chapter 4, Metal Structure, Welding, and Brazing, and is applicable to the installation of radio units in instrument panels.

3.4.1 Stationary Instrument Panels—Nonstructural and Structural. The stationary instrument panel in some aircraft is part of the primary structure. Prior to making any additional cutouts or enlargements of an existing cutout, determine if the panel is part of the primary structure. If the panel is structural, make additional cutouts or the enlargement of existing cutouts in accordance with the aircraft manufacturer’s instructions, or substantiate the structural integrity of the altered panel in a manner acceptable to the Administrator. Radius all corners and remove all burrs from the cutout and drilled holes.

3.4.2 Added Equipment Stationary Instrument Panel. When radio equipment is to be installed in a stationary panel already supporting instruments, glove compartments, etc., determine the capability of the panel to support the total load.

3.4.3 Case Support. To minimize the load on a stationary instrument panel, whenever practicable, install a support between the rear (or side) surface of the radio case and a nearby structural member of the aircraft (see Figure 3-2, Typical Fabricated Panel Mounting).

3.4.4 Added Equipment—Shock-Mounted Panels. When installing radio equipment designed for use in shock-mounted panels, the total accumulated weight of equipment installed must not exceed the weight carrying capabilities of the shock mounts. Determine whether the structure to which the shock mounts are connected is satisfactory for supporting the added weight.

3.4.5 Existing Factory Fasteners. When possible, use existing plate nuts and machine screws provided by the aircraft manufacturer to attach the radio case or rack. If additional fastening is required, use machine screws and elastic stop nuts (preferably plate nuts).

3.4.6 Magnetic Direction Indicator. As a function of the radio installation, determine if it is necessary to swing the compass. Install a suitable placard that indicates the compass error with the radio(s) on and off. Maximum acceptable deviation in level flight is 10 degrees on any heading. The following is an example of a typical compass calibration card. Refer to AC 43.13-1, Chapter 12, Aircraft Avionics Systems, on how to swing a compass.

3.5.1 Shock-Mounted Units. › 3.5.1.1 Wood or Composition Flooring.

Table 3-1. Typical Compass Calibration Card

FOR N 30 60 E 120 150

Radio On

Steer 4° 35° 63° 93° 123° 154°

Radio Off

Steer 358° 27° 58° 88° 118° 148°

FOR S 210 240 W 300 330

Radio On

Steer 183° 214° 244° 274° 304° 337°

Radio Off

Steer 178° 208° 238° 268° 293° 327°

3.5 Other Mounting Areas. The following are acceptable methods for installing radio equipment at other than instrument panel locations.

3.5.1 Shock-Mounted Units.

3.5.1.1 Wood or Composition Flooring. Secure the shock-mounted base assembly (suitable for radio unit) directly to the floor using machine screws. Add a doubler to the bottom of the floor, thereby sandwiching the composition floor between each shock-mount foot and the doubler. Subsequent removal and reinstallation of the shock-mount foot will be facilitated if plate nuts are secured to the doubler. Where practicable, use small retaining screws to keep the doubler in position. Install a ground strap between the radio rack and metal structure of the aircraft.

3.5.1 Shock-Mounted Units. › 3.5.1.2 Metal Flooring.

Figure 3-4. Typical Shock-Mounted Base (Wood or Composition Flooring)

3.5.1.2 Metal Flooring. Secure the shock-mounted base assembly directly to the floor using machine screws, washers, and self-locking nuts. Floor area under and around the radio mounting bases may require installation of doublers or other reinforcement to prevent flexing and cracking. Installation of plate nuts on the floor or doubler will facilitate removal and installation of the shock mounts. Install a ground strap between the shock mount foot and the radio rack.

Figure 3-5. Typical Shock-Mounted Base (Metal Flooring)

3.6 Fabrication of Supporting Brackets for Attachment to a Structure… › 3.6.3 Use a rivet size and pattern compatible with the aircraft…

3.5.2 Rigid-Mounted Unit Base. Secure radio mounting base plate(s) to the floor (wood, composite, or metal) using machine screws as shown in Figure 3-6. Use a reinforcing plate or large area washers or equivalent under wood or composite flooring. When the mounting base is secured to wood or composite material, install a ground strap between the base and aircraft metal structure.

Figure 3-6. Typical Rigid Base Plate Mount

3.6 Fabrication of Supporting Brackets for Attachment to a Structure Other Than Flooring.

3.6.1 Typical supporting brackets usually consist of a shelf or platform upon which the radio unit mounting base assembly can be installed in the same manner as described in paragraph 3.4.

3.6.2 Fabricate the bracket according to good aircraft design, layout, assembly practices, and workmanship to obtain results compatible with the airframe structure. Generally, the thickness of the bracket material will depend on the size or area of the platform and the load it must sustain according to the provisions set forth in Chapter 2.

3.6.3 Use a rivet size and pattern compatible with the aircraft structure to provide the strength needed to ensure support of the loads imposed under all flight and landing conditions.

Figure 3-7. Typical Underseat Installation

Note: To increase the strength of floor attachment points, metal reinforcement may be installed as needed.

3.7.2 Placard. › … lbs.”

3.7 Reinforcement of the Supporting Structure.

3.7.1 Attachments. Attach equipment to the aircraft’s supporting structure so that its supported load will be transmitted to aircraft structural members. If direct attachment to the existing structure (bulkheads, horizontal stringers, etc.) is not feasible, add the necessary stringers, doublers, bulkhead flange reinforcements, etc., to provide adequate support and ensure load transfer to the primary structure. When attaching to the existing structure, ensure the attachment does not weaken the structure. Alteration to the primary structure may require approved engineering data.

3.7.2 Placard. Fasten a permanent placard onto the shelf or bracket (as the example below) stating the design load that the installed structure is determined capable of supporting.

“Shelf load not to exceed

… lbs.”

Figure 3-8. Typical Remote Unit Mounting Base-Vertical or Horizontal Other Than

Structure to Floor

Figure 3-9. Typical Shelf Installation

Note 1: Use standard aircraft practices and procedures for fabrication and attachment of the shelf. Reinforce fore and aft corners with gussets or a bulb angle.

Note 2: Fabricate a platform using 2017T4(17ST) or equivalent. Apply standard aircraft practices for fabrication and installation.

Note 3: The equipment manufacturer’s mounting bases that meet load requirements and can be utilized are acceptable.

3.8 Electrical Requirements. › 3.8.4 Installation of Wiring.

Figure 3-10. Typical Attachment of Support Structure to Tubular Frame Other Than

Structure to Floor

3.8 Electrical Requirements.

3.8.1 Installing an electrical system or component into an aircraft requires consideration of the electrical load, the appropriate power distribution circuit, and available power capacity. The specific requirements for a system depend on its electrical characteristics and the criticality of its application for use in the aircraft’s operation.

3.8.2 The total energy available to power electrical systems is referred to as the aircraft’s capacity. It includes available stored power and generated power. This will vary depending on the phase of flight or type of operation.

3.8.3 The critical distribution circuit of an aircraft is designed to transfer power from the source to a system determined to be critical to the operation or function of the aircraft. This circuit is required to include additional capacity and circuit protection as required by applicable regulations. Distribution systems should be designed to facilitate loadshedding procedures. Power distribution system design includes the following concerns. Refer to AC 43.13-1, Chapter 11, Aircraft Electrical Systems, for:

• Circuit protection.

• Wire selection.

• Connectors, switches, and termination devices.

• Wire routing.

• Wiring/cable support.

• Identification.

3.8.4 Installation of Wiring. Select and use wiring of a type and design that is appropriate for the intended purpose of the application. Install in a manner suitably protected from fuel, oil, water, other detrimental substances, oxygen systems, and abrasion damages.

3.8 Electrical Requirements. › 3.8.9 Radio Bonding.

3.8.5 Power Sources.

3.8.5.1 Connect radio electrical systems to the aircraft electrical system at the power source protective device, a terminal strip, or use a plug and receptacle connection.

3.8.5.2 Radio electrical systems must function properly whether connected in combination or independent.

3.8.6 Protective Devices.

3.8.6.1 Incorporate a “trip free” (one that will trip open if the ON-OFF mechanism is held in the ON position) resettable type circuit breaker or a fuse in the power supply from the bus. Mount in a manner accessible to a crewmember during flight for circuit breaker resetting or fuse replacement and label.

3.8.6.2 Select circuit breakers or fuses that will provide adequate protection against overloading of the radio system wiring.

3.8.6.3 Connect all leads in such a manner that the aircraft’s master switch will interrupt the circuit when the master switch is opened, unless the equipment is intended to be powered when the master switch is open.

3.8.6.4 Radio system controls are to provide independent operation of each system installed and be clearly labeled to identify their function relative to the unit of equipment they operate.

3.8.7 Wire Bundle Separation From Flammable Fluid Lines.

3.8.7.1 Physically separate radio electric wire bundles from lines or equipment containing oil, fuel, hydraulic fluid, alcohol, or oxygen.

3.8.7.2 Mount radio electrical wire bundles above or on level with flammable fluid lines and whenever possible, maintain a minimum separation of 6 inches. Where separation is 1/2 to 2 inches, install clamps. Refer to AC 43.13-1, Chapter 11, Paragraph 11-127, Flammable Fluids and Gases.

3.8.8 Cable Attachment to Shock-Mounted Units. Route and support electrical wire bundles and mechanical cables in a manner that will allow normal motion of equipment without strain or damage to the wire bundles or mechanical cables.

3.8.9 Radio Bonding. It is advisable to electrically bond radio equipment to the aircraft in order to provide a low impedance ground and to minimize radio interference from static electrical charges. When electrical bonding is used, observe the following:

1. Keep bonding jumpers as short as possible.

2. Prepare bonded surfaces for best contact (resistance of connections should not exceed 0.003 ohm).

3.10 Electromagnetic Compatibility (EMC). › 3.10.1 EMI may disrupt the performance of systems and has varying…

3. Avoid use of solder to attach bonding jumpers. Clamps and screws are preferred.

4. For bonding aluminum alloy, use aluminum alloy or tinned, or cadmium-plated copper jumpers. Use brass or bronze jumpers on steel parts.

5. When contact between dissimilar metals cannot be avoided, put a protective coating over the finished connection to minimize corrosion.

3.9 Electrical Load Analysis Procedure.

3.9.1 Available Power Supply. To preclude overloading the electric power system of the aircraft when additional equipment is added, perform an electrical load analysis to determine whether the available power is adequate. Radio equipment must operate satisfactorily throughout the voltage range of the aircraft electrical system under taxi, takeoff, slow cruise, normal cruise, and landing operating conditions. Compute the electrical load analysis for the most adverse operating conditions; typically, this is for night and/or instrument flight.

3.9.2 ASTM Method. One method for the analysis may be found in the ASTM International F2490-20, Standard Guide for Aircraft Electrical Load and Power Source Capacity Analysis.

3.9.3 Previous Electrical Load Analysis. Applicable elements of a previously performed electrical load analysis if available may be reused.

3.10 Electromagnetic Compatibility (EMC).

3.10.1 EMI may disrupt the performance of systems and has varying degrees of consequence. These consequences may be identified as no safety effect, minor, major, hazardous, or catastrophic. The purpose of EMC analysis and testing is to ensure that equipment does not cause interference with any existing aircraft system function and that existing systems do not cause any interference with the new equipment (see Table 3-2, Relationship Probabilities and Severity of Failure Conditions).

3.10 Electromagnetic Compatibility (EMC). › 3.10.2 When EMC characteristics are known, the need for and extent of…

Table 3-2. Relationship Probabilities and Severity of Failure Conditions

Classification

of Failure Conditions

No Safety

Effect Minor Major Hazardous Catastrophic

Effect on

Airplane

No effect on

operational capabilities or

safety

Slight reduction in

functional capabilities or safety margins

Significant reduction in

functional capabilities or safety margins

Large reduction in

functional capabilities or safety margins

Normally with

hull loss

Effect on Occupants

Inconvenience

for passengers

Physical discomfort for

passengers

Physical distress to passengers,

possibly including

injuries

Serious or fatal injury to

an occupant

Multiple fatalities

Effect on Flightcrew

No effect on

flightcrew

Slight increase in workload or

use of emergency procedures

Physical discomfort or

a significant

increase in

workload

Physical distress or

excessive workload impairs ability

to perform

tasks

Fatal injury or

incapacitation

3.10.2 When EMC characteristics are known, the need for and extent of EMC testing can be determined by a review of those characteristics. Knowing specific target frequencies, EMC testing can focus on the aircraft systems, and even those susceptible frequencies in the case of tunable systems, likely to be affected by interference. Where sensitive systems or potentially strong sources of EMI are involved, more intensive evaluation will be required.

3.10.3 On-aircraft EMC tests for systems or equipment should be conducted. › 3.10.3.4 Aircraft systems being tested should be operated and monitored…

Table 3-3. Commonly Used Radio Frequencies on Aircraft

Range Hz Mode Function

190–1750 kHz Rx Automatic Direction Finder (ADF) Navigation

2–30 MHz Tx/Rx High Frequency (HF) Communications

75 MHz Rx Marker Beacon Receiver

108–112 MHz Rx Instrument Landing System (ILS) Localizer (LOC) Receiver

108–118 MHz Rx Very High Frequency (VHF) Omnidirectional Range (VOR) Receiver

118–137 MHz Tx/Rx VHF Communications

243 MHz Tx Emergency Locator Xmtr (Satellite)

328.6–335.4 MHz Rx ILS Glide Slope Receiver

406.3 MHz Tx ELT

960–1215 MHz Tx/Rx Distance Measuring Equipment (DME) System

1027–1033 MHz Tx/Rx Transponder and Traffic Alert and Collision Avoidance System

(TCAS) Systems

1087–1093 MHz Tx/Rx Transponder and TCAS Systems

1575.42 MHz Rx Global Positioning System (GPS) Satellite Navigation

3.10.3 On-aircraft EMC tests for systems or equipment should be conducted. If lab test data is available, it should be used to guide the planning of these tests. If lab test analysis is not available, a more comprehensive EMC testing on the aircraft systems and equipment typically needs to be performed.

3.10.3.1 The aircraft should not be close to large reflecting surfaces, such as buildings or other aircraft. The use of ground power is not recommended, unless the ground power unit that is used is routinely checked for output quality.

3.10.3.2 All normally closed-circuit breakers should be closed, and power should be supplied to all normally powered alternating current (AC) and direct current (DC) distribution busses during testing.

3.10.3.3 The aircraft should be in flight configuration. Doors and hatches that might be in any interfering signal’s path should be in the position they would normally be in during flight.

3.10.3.4 Aircraft systems being tested should be operated and monitored for indication of interference. It is essential that systems determined critical for the operation of the aircraft are tested. The following systems, if installed, should be included in the aircraft EMC test plan.

3.11 Functional Hazard Assessment (FHA). › 3.11.3 Evaluate the system to determine whether it is essential to safe…

Table 3-4. Aircraft Electrical and Electronic Systems

System

ADF

Air Data Systems (ADS)

Altitude Alert System

Air Traffic Control (ATC) Transponder

Audio Distribution System

Autopilot/Flight Guidance System (FGS)

Compass/Directional Gyro Systems

DME

Electronic Flight Control System

Electronic Flight Instrument System (EFIS)

GPS

Marker Receiver System

VHF Communications

VOR/Localizer (LOC)/Glideslope (GS)

Newly Installed Electrical/Electronic System

3.11 Functional Hazard Assessment (FHA).

Note: Refer to AC 23.1309-1 for additional information on FHA.

3.11.1 Many older aircraft designs did not provide for all weather operations or potential increases in the pilot’s reliance on installed systems and equipment. Requirements to ensure design safeguards against hazards have developed as technologies have become available and pilots have increased their reliance on installed systems and equipment. A fundamental analysis to ensure design safeguards is accomplished through an FHA.

3.11.2 Alterations that involve systems or equipment that perform critical functions or that include complex designs with a high degree of integration, use of new technology, or novel applications of conventional technology must be assessed to determine the severity of failure conditions. Complexity in itself does not drive the need to perform a system safety analysis, but the effect of a failure does. Comparison with similar previously approved systems is sometimes helpful.

3.11.3 Evaluate the system to determine whether it is essential to safe operation. For aircraft of 6,000 pounds or less maximum weight, refer to the regulations incorporated by reference in the type certificate (TC), unless the Administrator has found that the change is significant in an area.

3.11.7 Design requirements and the methodology of hazard resolution… › 3.11.7.4 If a probable failure or malfunction will result in a hazard…

3.11.4 Determine whether the equipment has any unacceptable adverse effects when operated.

3.11.5 Determine whether the operation of the installed equipment has an adverse effect on equipment that is not essential to safe operation, and whether a means exists to inform the pilot of the effect.

3.11.6 Determine whether a failure or malfunction of the installed equipment could result in unacceptable hazards.

3.11.7 Design requirements and the methodology of hazard resolution differ depending on the application and type of aircraft (i.e., single-engine, multiengine, and commuter use).

3.11.7.1 It is unacceptable to operate equipment that has an adverse effect on other equipment essential to the safe operation of the aircraft.

3.11.7.2 Operation of equipment that has an adverse effect on other equipment that is not essential to the safe operation of the aircraft may be acceptable if there is a means to inform the pilot of the effect.

3.11.7.3 It is unacceptable if a probable failure or malfunction will result in a hazard in a multiengine aircraft.

3.11.7.4 If a probable failure or malfunction will result in a hazard in a single-engine aircraft, its impact must be minimized.

CHAPTER 4. ANTENNA INSTALLATION

4.1 Purpose. The purpose of this chapter is to describe antenna installation methods and practices. An antenna that is installed on an aircraft must function properly and may not adversely affect other systems or equipment.

4.4 Structural Support. › 4.4.3 Since antenna systems typically require a ground plane (this may…

4.2 Hazards and Warnings.

4.2.1 Follow antenna manufacturer’s instructions and recommendations when they are available and appropriate and not contrary to the instructions of the aircraft manufacturer.

4.2.2 Extension of the landing gear or flaps may impact belly-mounted antenna performance.

4.3 Additional References. For further information concerning acceptable methods, techniques, and practices concerning alteration involving specific structures, refer to the appropriate chapter of AC 43.13-1, Acceptable Methods, Techniques, and Practices―Aircraft Inspection and Repair, and Civil Air Regulation (CAR) 6, Rotorcraft Airworthiness; Normal Category.

4.4 Structural Support.

4.4.1 The antenna’s structural load, plus any required allowances, may not exceed the design capacity of the structure intended to support it. It is important to understand the operational characteristics of the aircraft and consider forces that occur during flight (dynamic loading) as well as those that occur when the aircraft is not in motion (static loading). For example, an aircraft designed without flaps may employ a side slip procedure to lose altitude, during which the direction of airflow across the fuselage is not in line with the aircraft longitudinal axis. Antenna mountings on these aircraft need to be designed and evaluated for the direction of airflow that occurs during such an operation.

4.4.2 Whenever possible, an antenna should be mounted to a flat surface. Minor aircraft skin curvature can be accommodated with the use of an appropriate gasket, but if gaps over 0.020 inches appear between the base plate and mounting surface, use of a mounting saddle is recommended.

4.4.3 Since antenna systems typically require a ground plane (this may be a conductive surface that the antenna mounts to), any separation of an antenna from its ground plane may impact performance. Contact the manufacturer for recommendations if a gasket or mounting saddle is needed.

4.5 Physical Interference. › 4.5.1 Antennas should be located where they will not interfere with the…

Figure 4-1. Antenna Mount With Saddle

4.4.4 Mounting screws must never be over torqued in an attempt to distort aircraft structure to reduce gaps between the antenna base plate and aircraft-mounting surface.

4.4.5 Consider the factors of flutter, vibration characteristics, and drag load. The approximate drag load an antenna develops may be determined by the following formula:

D = 0.000327 AV2 (The formula includes a 90 percent reduction factor for the streamline shape of the antenna.) D is the drag load on the antenna in pounds. A is the frontal area of the antenna in square feet. V is the never-exceed speed (VNE) of the aircraft in miles per hour (mph). Example: Antenna manufacturer specification frontal area = 0.135 square feet and the VNE of the aircraft is 250 mph.

D = 0.000327 x .135 x (250)2 = 0.000327 x .135 x 62,500 = 2.75 pounds

4.4.6 The above formula may be adapted to determine side load forces by substituting the apparent frontal area value for A when the aircraft motion and antenna orientation are not the same.

4.5 Physical Interference.

4.5.1 Antennas should be located where they will not interfere with the operation of the aircraft or other aircraft systems. One such example of interference could be the obstruction of the visibility of a navigation position light or beacon.

4.5.2 Antennas should be located so that they do not obstruct or limit airflow to areas of the airframe that require airflow. Care should be exercised so that an antenna is not located where it will be damaged by heat from engine exhaust, fumes from battery vents, or fuel/fluid drains.

4.7 Antenna Location. › 4.7.5 If Com 2 is mounted under the aircraft, a bent whip may be…

4.5.3 Antennas may accumulate ice that can then depart and damage areas behind them. Special attention should be paid to areas of the airframe near pitot-static ports and sensors, and near flight controls since the antenna may alter airflow characteristics.

4.5.4 Antennas should be located in such a manner that they are not susceptible to damage from misuse, such as near a door where they might be mistaken for or used as a handhold.

4.6 Antenna Selection. The selection of an appropriate antenna will include consideration of system requirements and aircraft characteristics. The size and shape of an antenna vary with frequency, power rating, and maximum design speed of the antenna. See Figures 4-7, ADF Loop, through 4-19, DME/Transponder Blade, for pictures of typical antennas.

4.7 Antenna Location.

4.7.1 In general, antenna locations on an aircraft that provide unobstructed line-of-sight views of the transmitted or received signals are preferred. Objects located in the path of a signal may cause a blanking of antenna coverage and impact the performance of the system.

Note: Global Positioning System (GPS) antennas will not receive a signal if a line-of-sight view of a satellite is not available. Do not mount a GPS antenna on the underside of an aircraft.

4.7.2 The acceptable and unacceptable spacing between an antenna and an obstacle or the permissible interval between antennas is dependent upon operating frequency and system characteristics. When in doubt, contact the antenna manufacturer or system designer for further information.

4.7.3 Antennas should be separated as far as possible from interference sources (other radiating antennas, ignition noise sources, etc.). When known interference sources are present, it may be advisable to temporarily position an antenna and check the location for suitability prior to mounting the antenna.

4.7.4 Very high frequency (VHF) Com 1 should be mounted on the top of the aircraft since this will provide the best unobstructed location. VHF Com 2 can also be mounted on the top, provided there is at least 1/2 wavelength (of the antenna operating frequency) distance available between antennas.

4.7.5 If Com 2 is mounted under the aircraft, a bent whip may be required to provide ground clearance. Bent whips may not provide the best performance because of proximity to the aircraft skin. Signal reflection and obstruction is more of a problem with such locations.

Extension of the landing gear or flaps may also impact belly-mounted antenna performance.

4.8 Antenna Bonding. › 4.8.5 Antenna performance can be severely degraded from corrosion…

4.7.6 Antennas need to “see” with a direct line-of-sight to the source. Antenna patterns can be disrupted by landing gear or vertical stabilizers, for example. When mounting antennas, try to locate them in areas where line-of-sight view is not obstructed.

4.7.7 As a rule of thumb, maintain 36 inches as a minimum distance between antennas. Refer to the manufacturer’s installation guidelines for specific system limitations and requirements.

4.7.8 Antennas should be located such that the cables that run between the antenna and equipment are as short as practical. Signal loss of a cable is dependent upon cable design, length, and frequency. In some cases, cables must be specific lengths to provide a required capacitance, attenuation, or signal transmission time. VHF omnidirectional range (VOR)/Localizer (LOC)/glideslope (GS) blade or towel bar type antennas require the cables to their coupling assembly to be the exact same length to maintain a phase relationship.

4.8 Antenna Bonding.

4.8.1 The electrical bonding of the antenna to the aircraft surface is extremely important. The conductive skin of an aircraft is an electrical part of the antenna system. If an antenna is not properly bonded to the aircraft, its pattern may be distorted, and nulls in coverage may appear.

4.8.2 The electrical bonding of the antennas to the aircraft skin of a metal aircraft is best accomplished by direct metal-to-metal contact of the antenna base to the skin. A resistance of no more than 0.003 ohms between the antenna base plate and skin should be achieved.

Note: To achieve this electrical bonding, the aircraft paint in the mounting area will need to be removed and the surface covered with an oxide film (i.e., aluminum conversion coat) to protect aluminum against corrosion in accordance with MIL-DTL-5541.

4.8.3 An alternate method for providing electrical bonding to metal aircraft skin is through the antenna mounting screws, which attach to a backing plate inside the aircraft, making electrical contact with the backside of the skin. To ensure good contact, remove any interior paint in the area where the backing plate is placed and coat this area in accordance with MIL-C-5541B to minimize corrosion.

4.8.4 Composite or fabric-covered aircraft that do not provide a conductive mounting surface generally require fabrication of a conductive surface (ground plane) and bonding through the mounting screws.

4.8.5 Antenna performance can be severely degraded from corrosion caused by moisture accumulation where the antenna electrically bonds to its ground plane. It is advisable to

4.10.2 General Practices. › 4.10.2.4 Sandwich the aircraft skin between the antenna base plate and…

apply room temperature vulcanizing (RTV) around the antenna edges to seal the antenna bond. However, always ensure chemical compatibility before using any sealant.

4.9 Electromagnetic Interference (EMI).

4.9.1 Since an antenna’s purpose is to either receive or transmit radio frequency (RF) energy, or both, it is essential to consider EMI.

4.9.2 Antenna mounting positions that are as far as possible from an EMI source should be selected. In special cases, it may be possible to employ filters or select an antenna that has been specifically designed to be resistant to EMI.

4.9.3 EMI test procedures are found in Chapter 3, Communication, Navigation, and Emergency Locator Transmitter System Installations.

4.10 Mechanical Installation.

4.10.1 Mounting Hardware.

4.10.1.1 Typical antenna installations employ either #8-32 or #10-32 stainless steel mounting screws.

4.10.1.2 Some designs require a pan head screw. For others, a counter sunk screw is required.

4.10.1.3 Mounting screw length will vary based on each particular installation requirement.

4.10.2 General Practices.

4.10.2.1 Before drilling holes in the aircraft skin, refer to the installation drawing to determine the proper size and spacing.

Note: When replacing antennas, it is important to match the original mounting holes. Previous mounting holes that are not reused with appropriate hardware must be repaired, and the mounting location must be returned to its design strength.

4.10.2.2 It is highly recommended to use a structural backing plate. Backing plates strengthen the immediate point of attachment, but if they are not attached to a load-carrying structure, they do not provide structural load support.

4.10.2.3 To properly secure the antenna, mounting screws should be secured with stainless steel nuts with flat washers and lock washers, or with flat washers and lock nuts.

4.10.2.4 Sandwich the aircraft skin between the antenna base plate and the internally mounted backing plate. Before securing the antenna to the aircraft, make sure

4.11 Ground Plane Requirement (Wood/Fabric and Composite Aircraft). › 4.11.4 Be sure the ground plane is well attached to the airframe with…

all the cables are connected to the unit and fit through the connector holes in the aircraft.

4.10.2.5 Gently tighten the mounting hardware so that uniform stress is placed on each side of the antenna. For #8-32 screws, do not exceed 20 in/lbs of torque, and for #10-32 screws, do not exceed 23 in/lbs of torque. Refer to the fastener manufacturer’s torque guidelines to confirm that these recommended settings do not exceed the chosen fastener’s torque limits.

4.10.2.6 Once the antenna is mounted, any minor gaps between the base plate or gasket and aircraft skin should be filled with RTV silicone adhesive sealant.

4.10.2.7 Double-check that a reading of 0.003 ohms between the antenna base plate and ground has been achieved.

4.11 Ground Plane Requirement (Wood/Fabric and Composite Aircraft).

4.11.1 When the antenna is not mounted to a conductive surface capable of providing a required ground plane for operation, a ground plane must be fabricated.

4.11.2 Most antennas require a ground plane size of approximately 24 inches by 24 inches. While the rule of thumb is to provide a minimum of 1/4 wavelength of the operation frequency, larger is better, and ground plane symmetry is critical. Gaps in antenna coverage or performance may occur if a ground plane is not symmetrical.

Table 4-1. Wavelength in Feet = 984/Frequency in Megahertz (MHz)

Frequency Wavelength (feet) 1/4 Wavelength (inch)

75 MHz 13.1 40

125 MHz 7.9 24

1,000 MHz 1 3

4.11.3 Wire mesh is the best material to use when a solid plate is not practical. Heavy aluminum foil can also be used. In all cases, electrical continuity from the ground plane to the airframe ground is essential.

4.11.4 Be sure the ground plane is well attached to the airframe with cement or epoxy if not otherwise supported. This will prevent noise problems or erratic operation that could occur if the plane moves. Capacitance will occur as an antenna base is separated from its ground plane. This may distort antenna coverage or operation.

Figure 4-2. Antenna Ground Plane for Nonconductive Mount

Figure 4-3. One Means to Provide Adequate Antenna Bonding Through a Composite

Airframe

Figure 4-4. Use Bushings for All Screws

Note: Carbon fiber composite material, while conductive, has not been found to be adequate as a ground plane.

4.11.5 Refer to AC 43.13-1, Chapter 3, Fiberglass and Plastics, for acceptable methods, techniques, and practices applicable to fiberglass and plastics.

4.12 Antenna Feed Line Balun. › 4.12.3 Refer to AC 43.13-1, Chapter 11, Aircraft Electrical Systems,…

4.12 Antenna Feed Line Balun.

4.12.1 Antenna cables (electrical feed lines) may be designed to be electrically balanced or unbalanced. Certain antenna designs incorporate dual elements with a requirement for balanced input. In these cases, standard cables that are unbalanced are generally employed for the cable run, and a balancing transformer is located at the antenna feed connection.

4.12.2 A balun is a device that converts an unbalanced feed into a balanced input and may include a transformer that matches feed impedance to provide maximum signal transfer. Follow the manufacturer’s installation procedures when a balun is required. Some balun designs require the balun to be grounded to the airframe.

4.12.3 Refer to AC 43.13-1, Chapter 11, Aircraft Electrical Systems, for bonding practices.

Figure 4-5. Typical Dipole Antenna Assembly

CHAPTER 4. ANTENNA INSTALLATION › 4.13 Antenna Repair.

Figure 4-6. Typical VOR Balun

4.13 Antenna Repair. Painting an antenna or applying protective coatings or devices that are not approved are not allowed under this AC. Paint is an RF detuner. If an antenna is painted in the field, paint type and paint thickness present uncontrolled variables that will affect an antenna’s performance and may result in the antenna no longer meeting its specifications or Technical Standard Order (TSO).

Figure 4-7. ADF Loop

Figure 4-8. ADF Combined Sense Loop

Figure 4-9. Communications (COM) Whip

Figure 4-10. COM Whip Bent

Figure 4-11. Emergency Locator Transmitter

Figure 4-12. Global Positioning System

Figure 4-13. Glideslope

Figure 4-14. Marker

Figure 4-15. Combined COM/VOR

Figure 4-16. VOR Rabbit Ear

Figure 4-17. VOR Blades

Figure 4-18. Transponder/DME Probe

Figure 4-19. DME/Transponder Blade

5.3 Regulations and Other References. › 5.3.5 Supplementary lights may be installed, in addition to position…

CHAPTER 5. ANTICOLLISION AND SUPPLEMENTARY LIGHT INSTALLATION

5.1 Purpose. This chapter gives procedures and standards to be used when replacing older rotating beacon assemblies and wing lights with strobe or other anticollision systems. This chapter assumes that the newer units have FAA approval in the form of a Parts Manufacturer Approval (PMA) or Technical Standard Order (TSO) and not an experimental or aviation unit.

5.2 Hazards and Warnings. When installing anticollision lights, take care to ensure the unit is properly grounded, the airframe structure can support the new unit, and the aircraft wiring is of the correct size. Mechanics should take special precautions to protect their eyes when testing the new unit. Strobe lights are especially hazardous in dark or darkened hangars when activated.

5.3 Regulations and Other References. The operational requirements for anticollision lights can be found in 14 CFR § 91.205. Information regarding installation requirements for nontransport category aircraft is included in 14 CFR §§ 23.1401 and 27.1401. Additional information can be found in AC 20-30, Aircraft Position Light and Anticollision Light Installations; AC 20-74, Aircraft Position and Anticollision Light Measurements; and Civil Air Regulation (CAR) 6, Rotorcraft Airworthiness; Normal Category. Aircraft for which an application for type certificate (TC) was made before April 1, 1957, may conform to either the above regulations or to the following standards:

5.3.1 Anticollision lights, when installed, should be installed on top of the fuselage or tail in such a location that the light will not impair the flight crewmembers’ vision and will not detract from the conspicuity of the position lights. If there is no acceptable location on top of the fuselage or tail, a bottom fuselage or wing tip installation may be used.

5.3.2 The color of the anticollision light must be either aviation red or aviation white in accordance with the specifications of 14 CFR § 23.1397 or 14 CFR § 27.1397, as applicable.

5.3.3 The arrangement of the anticollision light system (i.e., number of light sources, beam width, speed of rotation, other characteristics, etc.) must give an effective flash frequency of no less than 40 but not more than 100 cycles per minute. The effective flash frequency is the frequency at which the aircraft’s complete anticollision light system is observed from a distance and applies to each sector of light, including any overlaps that exist when the system consists of more than one light source. In overlaps, flash frequencies may exceed 100 but not more than 180 cycles per minute.

5.3.4 The system must consist of enough lights to illuminate the vital areas around the aircraft, considering the physical configuration and flight characteristics of the aircraft. The field of coverage must extend in each direction within at least 75 degrees above and 75 degrees below the horizontal plane of the aircraft. The minimum light intensity and minimum effective intensities are given in 14 CFR §§ 23.1401 and 27.1401, respectively.

5.3.5 Supplementary lights may be installed, in addition to position and anticollision lights required by applicable regulations, provided that the required position and anticollision

CHAPTER 5. ANTICOLLISION AND SUPPLEMENTARY LIGHT INSTALLATION › 5.7 Electrical Installation.

lights are continuously visible and unmistakably recognizable and their conspicuity is not degraded by such supplementary lights.

5.4 Operational Considerations: Crew Vision. Partial masking of the anticollision light may be necessary to prevent direct or reflected light rays from any anticollision or supplementary light from interfering with crew vision. Determine if the field of coverage requirements are met. An acceptable method of preventing light reflection from the propeller disc, nacelle, or wing surface is an application of nonreflective paint on surfaces that present a reflection problem. Perform a night flight check to ensure that any objectionable light reflection, sometimes known as flicker vertigo, has been eliminated. Enter a notation to that effect in the aircraft records.

5.5 Installation Considerations.

5.5.1 Communication and Navigation. Ensure that the installation and operation of any anticollision or supplementary light does not interfere with the performance of installed communication or navigation equipment. Capacitor discharge light (strobe) systems may generate radio-frequency interference (RFI). This radiated interference can be induced into the audio circuits of communication or navigation systems and is noticeable by audible clicks in the speaker or headphones. The magnitude of RFI disturbance does not usually disrupt the intelligence of audio reception.

5.5.2 Precautions. RFI can be reduced or eliminated by observing the following precautions during installation of capacitor discharge light systems:

1. Locate the power supply at least 3 feet from any antenna, especially antennas for radio systems that operate in the lower frequency bands.

2. Ensure that the lamp unit (flash tube) wires are separated from other aircraft wiring, placing particular emphasis on coaxial cables and radio equipment input power wires.

3. Make sure that the power supply case is adequately bonded to the airframe.

4. Ground the shield around the interconnecting wires between the lamp unit and power supply at the power supply end only.

5.6 Markings and Placards. Identify each switch for an anticollision/supplementary light and indicate its operation. The aircraft should be flight tested under haze, overcast, and visible moisture conditions to ascertain that no interference to pilot vision is produced by operation of these lights. If found unsatisfactory by test or in the absence of such testing, a placard should be provided to the pilot stating that the appropriate lights be turned off while operating in these conditions.

5.7 Electrical Installation. Install an individual switch for the anticollision light or supplementary light system that is independent of the position light system switch. Data for the installation of wiring, protection devices, and generator/alternator limitations is contained in AC 43.13-1, Acceptable Methods, Techniques, and Practices—Aircraft Inspection and Repair, Chapter 11, Aircraft Electrical Systems. Ensure that the terminal voltage at each light is within the limits as prescribed by the manufacturer.

5.8 Alteration of Structure. › 5.8.2 When a formed angle stringer is cut and partially removed,…

5.8 Alteration of Structure.

5.8.1 The simplest light installation is to secure the light to a reinforced fuselage skin panel. The reinforcement doubler shall be of equivalent thickness, material, and strength as the existing skin. (Install as shown in Figure 5-1.)

Figure 5-1. Typical Anticollision or Supplementary Light Installation in a Skin Panel

(Unpressurized)

5.8.2 When a formed angle stringer is cut and partially removed, position the reinforcement doubler between the skin and the frame. The doubler is to be equivalent to the stringer in thickness and extend lengthwise beyond the adjacent fuselage frames. The distance between the light and the edge of the doubler is to be twice the height of the doubler flange (see Figure 5-2, Typical Anticollision or Supplementary Light Installation Involving a Cut Stringer (Unpressurized), for typical installation).

5.8 Alteration of Structure. › 5.8.4 Vertical stabilizer installations may be made on the aircraft if…

Figure 5-2. Typical Anticollision or Supplementary Light Installation Involving a Cut

Stringer (Unpressurized)

5.8.3 Engineering evaluation is required for installations involving the cutting of complex formed or extruded stiffeners, fuselage frames, or pressurized skin of pressurized aircraft.

5.8.4 Vertical stabilizer installations may be made on the aircraft if the stabilizer is large enough in cross-section to accommodate the light installation and if aircraft flutter and vibration characteristics are not adversely affected. Locate such an installation near a spar, and add formers as required to stiffen the structure near the light. A typical installation is shown in Figure 5-3, Typical Anticollision or Supplementary Light Installation in a Fin Tip.

5.8 Alteration of Structure. › 5.8.5 Rudder installations are not recommended because of the possible…

Figure 5-3. Typical Anticollision or Supplementary Light Installation in a Fin Tip

Note: Skin thickness of the mounting ring and fairing are at least equivalent.

5.8.5 Rudder installations are not recommended because of the possible structural difficulties. However, if such installations are considered, an FAA engineering evaluation must be made to determine whether the added mass of the light installation will adversely affect the flutter and vibration characteristics of the tail surfaces.

6.4 Installation Considerations. › 6.4.1 Determining Eligibility of an Airplane.

CHAPTER 6. SKI INSTALLATIONS

6.1 Purpose. This chapter provides information about ski installations on small airplanes. The information provided for main ski and nose ski installations applies to wheel replacement skis only. Tire-cushioned skis other than tail skis, wheel penetration skis, and hydraulically adjustable or retractable skis involve special considerations and cannot be installed by relying solely on data in this AC.

6.2 Hazards and Warnings. Operation of ski planes exposes the airplane and its occupants to additional risks not associated with wheel-equipped landplanes. The additional weight and surface area of skis impose additional ground and air loads on the airplane. Ground handling, taxiing, takeoff, and landing can place significant side loads and twisting moments on the landing gear and its attachment structure, which can cause hidden or cumulative damage, or both. Improper rigging, weak springs or shock cords, or all, can cause the skis to “dump,” or rotate nose down in flight, possibly rendering the airplane uncontrollable or causing it to break up in flight. Skis with weak springs or shock cords may rotate nose down and “dig,” or penetrate the snow, during takeoff or landing on uneven or drifted snow, which could result in an accident. In-service failure of ski attachment hardware, springs, shock cords, or cables creates a high risk of those parts or a ski itself entering the propeller arc, which has resulted in complete loss of airplanes in flight. For these reasons, proper installation, rigging, periodic inspection, and maintenance of skis and their attaching parts are of utmost importance to safety. Consultation with experienced ski maintenance technicians and operators is strongly recommended when considering any new ski installation or any alteration of an existing ski installation.

6.3 Additional References (current editions).

• Airframe and ski manufacturers’ data, if available.

• AC 43.13-1, Acceptable Methods, Techniques, and Practices―Airplane Inspection and Repair.

• AC 43-210, Standardized Procedures for Obtaining Approval of Data Used in the Performance of Major Repairs and Major Alterations.

• Civil Air Regulation (CAR) 6, Rotorcraft Airworthiness; Normal Category.

• FAA Order 8110.54, Instructions for Continued Airworthiness Responsibilities, Requirements, and Contents.

• FAA-H-8083-23, Seaplane, Skiplane, and Float/Ski Equipped Helicopter Operations Handbook.

6.4 Installation Considerations.

6.4.1 Determining Eligibility of an Airplane. Only an airplane approved for operation on skis is eligible for ski installations in accordance with this chapter. Eligibility can be determined by referring to the aircraft specifications, Type Certificate Data Sheets (TCDS), aircraft listing, summary of Supplemental Type Certificates (STC), or by contacting the

6.4 Installation Considerations. › 6.4.5 Landing Gear Moment Reactions: Landing Gear Bending Moments.

manufacturer. Also, determine the need for any required alterations to the airplane to make it eligible for ski operations. Refer to ski plane-specific entries throughout TCDS A4CE on airspeeds, Weight and Balance (W&B) limitations and additional placards, and the Required Equipment listing for the first model in Aircraft Specification A-790 for examples. If the airplane is not approved in a ski plane configuration by type design, then skis cannot be installed by relying solely on data in this AC. Contact FAA engineering for approval or obtain or develop approved data from another source.

6.4.2 Identification of Approved Model Skis. Determine that the skis are of an approved model by examining the identification plates or placards displayed on the skis. Skis of approved models will have such plates or placards, and the Technical Standard Order (TSO)-C28; an aircraft component, accessory, or equipment type certificate (TC) number; or an airplane part number (if the skis have been approved as part of the airplane) will be engraved or imprinted on each plate or placard.

6.4.3 Maximum Limit Load Rating.

6.4.3.1 Known Limit Landing Load Factor. Before installation, determine that the maximum limit load rating (L) of the ski, as specified on its identification plate or placard, is at least equal to the maximum static load on it (S) times the limit landing load factor (fl) previously determined from drop tests of the airplane by its manufacturer. This requirement can be expressed by the following equation:

L = S x fl

6.4.3.2 Unknown Limit Landing Load Factor. In lieu of a value fl determined from such drop tests, a value of fl determined from the following formula may be used:

9000 η = 2.80 + (W + 4000) where “W” is the certificated gross weight of the airplane

6.4.4 Oversize Ski Installations. This limitation is to ensure that the oversize skis will not adversely affect the performance, stability, controllability, and spin recovery behavior of the airplane or impose excessive loads on it.

6.4.5 Landing Gear Moment Reactions: Landing Gear Bending Moments. In order to avoid excessive bending moments on the landing gear and attachment structure, the ski pedestal height measured from the bottom surface of the ski to the axle centerline must not exceed 130 percent of the static rolling radius of the standard tire approved for the airplane when the tire is installed on the standard wheel at the approved inflation pressure. Do not use oversized or “tundra” tires to determine the static rolling radius.

6.5 Fabrication and Installation. › 6.5.1 Hub-Axle Clearance.

6.5 Fabrication and Installation.

6.5.1 Hub-Axle Clearance. The pedestal hub should fit the axle to provide a clearance of 0.005 inch minimum to 0.020 inch maximum. Hubs may be bushed to adjust for axle size, using any ferrous or nonferrous metal, hard rubber, or fiber. If rubber or fiber bushings are used, use retaining washers of sufficient size on each side to retain the hub if the bushing should slip or fail (see Figure 6-1). Field experience has shown that the use of good quality, low-temperature grease, particularly modern synthetic-based grease, improves ski operation and wear protection when used on the axle-to-hub or axle-to-bushing faying surfaces.

Figure 6-1. Typical Hub Installation

6.5.3 Cable and Shock Cord Attachment and Attachment Fittings. › 6.5.3.2 Separating Attachment Points.

Figure 6-2. Typical Ski Installation

6.5.2 Crust-Cutter Cables. Crust-cutter cables are optional. However, when operating in severe crust conditions, it is advisable to have this cable installed to prevent the shock cord from being cut if the ski’s nose breaks through the crust while taxiing.

6.5.3 Cable and Shock Cord Attachment and Attachment Fittings.

6.5.3.1 Field Experience. Service reports indicate that failure of the ski itself is not a predominant factor in ski failures. Rigging, which is improper tension and terminal attachments, and cast-type pedestal material failures are predominant. Failures of the safety cable and shock cord attachment fittings usually occur at the ski end and not at the fuselage end.

6.5.3.2 Separating Attachment Points. It is strongly recommended that tension cords and safety cables be attached to entirely separate fittings at their fuselage ends. Although the attachment fitting detail shown in Figure 6-2 may be adequate for some installations where alternate attachment locations are unavailable, we recommend that each cord and cable be attached to its own fitting (such as the right-hand fitting in Figure 6-3, Typical Fuselage Fittings) and attached at separate points on the fuselage when possible. Provide a

6.5.3.3 Fabrication. › 6.5.3.3.2 Shock cord ends may be fabricated by any of the following methods

separate means of attaching cables and shock cords at the forward and aft ends of the skis.

6.5.3.3 Fabrication. Approved skis are normally supplied with cables, shock cords, and fittings. However, the specifications in Table 6-1, paragraphs 6.5.3.3.1 through 6.5.3.3.3, and Figure 6-3 may be used for fabricating and installing cables, shock cord assemblies, and fuselage fittings.

Note: Field experience indicates that accelerated wear and damage can occur to a 1/8-inch safety or crust-cutting cable and its attachment hardware in normal service on skis having a limit load rating of 1,500 pounds or more. The FAA recommends a minimum cable size of 5/32 inch for use in fabricating safety or crust-cutting cables for use with skis of a 1,500 pounds or greater limit load rating. 1/8-inch cables may be suitable for use on airplanes with light-weight skis and maximum certificated weights less than 1,500 pounds, such as those meeting the definition of light sport aircraft.

Table 6-1. Recommended Minimum Cable and Shock Cord Sizes

Ski Limit

Load Rating (Pounds)

Single Safety

Cable

Double

Safety

Cable

Single Crust-Cutting

Cable

Double Crust-Cutting

Cable

Single Shock Cord

Double

Shock

Cord

Less than 1,500 1/8 inch 1/8 inch 1/8 inch 1/8 inch 1/2 inch 1/2 inch

1,500–3,000 5/32 inch 5/32 inch 5/32 inch 5/32 inch 1/2 inch 1/2 inch

3,000–5,000 Do Not Use 5/32 inch 5/32 inch 5/32 inch Do Not Use 1/2 inch

5,000–7,000 Do Not Use 5/32 inch 5/32 inch 5/32 inch 3/4 inch 3/4 inch

7,000–9,000 Do Not Use 3/16 inch Do Not Use 5/32 inch Do Not Use 3/4 inch

6.5.3.3.1 Make check cable, safety cable, and crust-cutting cable ends by the splice method or swaging, such as the Nicopress process. Cable clamps may be used if adjustable lengths are desired, but they are not recommended. Use standard airplane hardware only. (Hardware used to attach cables must be compatible with cable size.) Refer to AC 43.13-1, Chapter 7, Aircraft Hardware, Control Cables, and Turnbuckles, for more information on cable fabrication.

6.5.3.3.2 Shock cord ends may be fabricated by any of the following methods:

1. Make a wrapped splice using a properly sized rope thimble and No. 9 cotton cord, 0.041 inch (minimum) safety wire (refer to Aerospace Industries Association (AIA) National Aerospace Standard (NAS) NASM20995, Wire, Safety or Lock), 1025 steel, or its equivalent

(AISI 4130). Attach with a clevis or spring steel snap fastener. (Do not use cast iron snaps.)

6.5 Fabrication and Installation. › 6.5.4 Provisions for Inspection.

2. Use approved spring-type shock cord end fasteners, 1025 steel, or its equivalent (AISI 4130).

6.5.3.3.3 Fitting (Figure 6-3) specifications and installation:

1. Fittings fabricated for 1/8-inch cable or 1/2-inch shock cord must be at least 0.065-inch 1025 steel or its equivalent.

2. Fittings fabricated for 5/32-inch cable or 3/4-inch shock cord must be at least 0.080-inch 1025 steel or its equivalent.

3. An improperly installed fitting may impose excessive eccentric loads on the fitting and attach bolts and result in failure of the fitting or bolts.

4. If attaching cables directly to holes in fittings, radius the hole edges to reduce stress concentration and accelerated wear of the thimble. Stainless steel thimbles are recommended for increased wear resistance.

5. If attaching cables to fittings using clevises, clevis bolt castellated nuts should be used and then properly torqued and safe tied with cotter pins. Field experience has shown that diaper-pin-style quick-releasing safety devices are more prone to failure during operation and are not recommended.

Figure 6-3. Typical Fuselage Fittings

6.5.4 Provisions for Inspection. An airplane using fabric-covered landing gear should have at least the lower 4 inches of fabric removed to facilitate inspection of the axle attachment area and to prevent the entrapment of snow and ice, which can lead to damage and corrosion of the landing gear (see item 6 in Figure 6-2).

6.6.2 Main Ski Incidence Angles. › 6.6.2.3 Adjust the length of the safety cable to provide a -20 to…

6.6 Rigging of Skis.

6.6.1 Location of Attach Fittings on Fuselage or Landing Gear. Locate fittings so the shock cord and cable angles are not less than 20 degrees when measured in the vertical plane with the shock absorber in the fully extended position (see angle B, Figures 6-4, Main Ski at Maximum Positive Incidence (Check Cable Taut), and 6-5, Main Ski at Maximum Negative Incidence (Safety Cable Taut)).

Note: Do not attach fittings to wing-brace struts, except by special approval, either manufacturer or FAA.

6.6.2 Main Ski Incidence Angles.

6.6.2.1 Set cable lengths with the airplane level and no weight on the landing gear.

6.6.2.2 Adjust the length of the check cable to provide a 0 (zero) to 5-degree ski incidence angle (see Figures 6-4 and 6-6, Main Ski Incidence Angles).

6.6.2.3 Adjust the length of the safety cable to provide a -20 to -35-degree ski incidence angle (see Figures 6-5 and 6-6).

Figure 6-4. Main Ski at Maximum Positive Incidence (Check Cable Taut)

6.6.3 Tension Required in Main Ski Shock Cords. › 6.6.3.1 Apply sufficient shock cord tension to the forward ends of the…

Figure 6-5. Main Ski at Maximum Negative Incidence (Safety Cable Taut)

Figure 6-6. Main Ski Incidence Angles

6.6.3 Tension Required in Main Ski Shock Cords.

6.6.3.1 Apply sufficient shock cord tension to the forward ends of the skis to prevent flutter and “dumping” throughout the range of airspeeds and attitudes at which the airplane will operate on skis. Because of the various angles used in attaching the shock cord to the skis, shock cord tension cannot be specified. It is possible to specify the downward force that must be applied to the forward end of the ski in order to overcome the shock cord tension and cause the check cable to slacken when the ski is in the normal flight attitude. That downward force is commonly referred to as the shock cord tension force or simply the tension force. In most installations on rigid, truss type landing gear, the

6.6.5 Nose Ski Installation. › 6.6.5.2 Where it is possible for the nose ski rigging to contact the…

tension force should be approximately as listed in Table 6-2, Approximate Main Ski Tension Forces.

Table 6-2. Approximate Main Ski Tension Forces

Ski Limit Load

Rating

Downward Force

(Pounds)

1500–3000 20–40

3000–5000 40–60

5000–7000 60–120

7000–9000 120–200

Note: Do not rely upon these tension force values for main ski installations on airplanes with spring steel or other flexible landing gear. Shock cord tensions great enough to require the downward forces listed in Table 6-2 to overcome them may produce excessive toe-in of the main skis on such airplanes. Variations in gear leg flexibility make it difficult to establish a generic table of tension forces appropriate for all airplanes with flexible landing gear.

6.6.3.2 The shock cord tension must also be sufficient to return the skis to the normal flight attitude from their maximum negative incidence at all airspeeds up to the airplane’s never-exceed speed (VNE) with skis installed. In the absence of more precise data, each shock cord must be able to produce a nose-up moment about the ski pedestal bearing centerline of M = (0.0000036)(W)(VNE)2 ft/lbs, when the ski is at its maximum negative incidence, where W is the maximum certificated gross weight of the airplane, and VNE is its never-exceed speed with skis installed.

6.6.4 Springs in Place of Shock Cords. If springs are used in place of shock cords to provide rigging tension, they must be able to withstand extreme cold and slight external scratching without premature fatigue failure and must not cause skis, rigging, or landing gear to experience flutter or objectionable vibration during airplane flight and dive tests.

6.6.5 Nose Ski Installation. Install the nose ski on an airplane with tricycle landing gear in the same manner as the main skis (see Figure 6-7, Typical Nose Ski Installation), except:

6.6.5.1 Adjust the length of the safety cable to provide ±5- to ±15-degree ski incidence.

6.6.5.2 Where it is possible for the nose ski rigging to contact the propeller tips due to vibration, install a 1/4-inch shock cord to hold the rigging out of the propeller arc.

6.6.6 Tail Ski Installation. › 6.6.6.3 The shock cord (see Figure 6-8) must be of a length that will…

Figure 6-7. Typical Nose Ski Installation

6.6.6 Tail Ski Installation.

6.6.6.1 When installing a tail ski on an airplane with conventional landing gear, use a tail ski that has been approved on an airplane of approximately the same weight and whose tail wheel bears approximately the same fraction of that weight when the airplane is in the three-point attitude (within 10 percent) or select the tail ski as outlined in paragraphs 6.2 and 6.4. Some types of tail ski require that the tail wheel be removed to install the rest on its upper surface ski.

6.6.6.2 Adjust the length of the limiting cable (see Figure 6-8, Typical Tail Ski Installation) to allow the ski to turn approximately 35 degrees to either side of the straight-forward position with the weight of the airplane resting on the ski.

6.6.6.3 The shock cord (see Figure 6-8) must be of a length that will hold the ski in the straight-forward position during flight.

Continue reading ↓ 120 of 366 passages shown