Radar Vectors
Advisory Circular Cancelled Issued Jul 15, 2003 AEE-100 211 pages Copy saved Nov 18, 2026

AC 36-4C Noise Standards: Aircraft Type and Airworthiness Certification

Promotes uniformity of implementation of the noise certification requirements of Part 36 of the Federal Aviation Regulations (FAR) by presenting technically acceptable test, analysis, and documentation procedures for subsonic turbojet airplanes that may be used by applicants for demonstrating compliance with Part 36. Where appropriate, FAA policy governing such certifications is reviewed.

This document is cancelled. Cancelled by 36-4D. Check the official source before relying on it.

Official source ↗ Open PDF

FAA Form 1320-15 (4-82) Supersedes WA Form 1320-2

U.S. Department of Transportation

Federal Aviation Administration

Advisory Circular

Subject: NOISE STANDARDS: AIRCRAFT TYPE AND AIRWORTHINESS CERTIFICATION

Date: 7/15/03 Initiated by: AEE-100

AC No: 36-4C Change:

1. PURPOSE.

a. Contents: This advisory circular (AC) contains information concerning the aircraft noise certification requirements of part 36 of the United States Code of Federal Regulations (CFR) Title 14. The document includes general information, references and definitions related to part 36, followed by regulatory language of all sections of part 36 Subparts and Technical Appendices. Explanations of regulatory language, FAA policies for implementation of the regulatory language and other guidance information are provided for each section, as appropriate. Four appendices are also attached and referenced within the body of the AC. These include the ICAO Environmental Technical Manual as identified below, a description of FAA procedures for auditing an applicant’s data adjustment and analysis methods, a methodology for adjusting data for the effects of ambient noise, and information on equivalent procedures and demonstrating “no acoustical change” for propeller-driven small airplanes and commuter category airplanes. The regulation that this AC references to is part 36, as amended through August 7, 2002 (Amendment 36-24).

Subject: NOISE STANDARDS: AIRCRAFT TYPE AND AIRWORTHINESS CERTIFICATION

b. Scope: This AC provides information for interested parties (such as regulatory authorities, aircraft manufacturers, acoustic consultants, airline and airport operators and others) on compliance with the part 36 noise certification regulations, including FAA policies and interpretations of regulatory language and other technical guidance applicable to noise certification processes for airplane and rotorcraft classes of aircraft. It is applicable for noise certification of normal, utility, acrobatic, commuter and transport category airplanes and normal and transport category rotorcraft as defined in part 21. This AC does not change regulatory requirements and does not authorize changes in, or deviations from, regulatory requirements. This document contains some mandatory language, where it is appropriate, as well as language that is permissive and advisory in nature. Mandatory language (e.g. the term “must”) is used in the AC for “Explanations of regulatory language”. Mandatory language is also used for certain “Supplementary Information” and “ Procedures” to reflect FAA policies regarding compliance with the intent of regulatory language. Permissive language (e.g. the term “should”) is used in this AC, to identify conditions and/or methods and procedures that may be acceptable to the FAA for purposes of aircraft noise certification based upon experience to date, but where an applicant is not constrained from considering or validating and proposing alternatives for compliance with part 36.

The FAA Office of Environment and Energy (AEE) (located in Washington DC) has approved a substantial number of equivalent procedures proposed by applicants. Many of these equivalent procedures are referred to in this document because, through their extensive usage by applicants, they have become acceptable practices for aircraft noise certification applications. Appendix 1 of this document is Steering Group Approved Revision 7 (SGAR7) of the “Environmental Technical Manual On The Use Of Procedures in The Noise Certification Of Aircraft” developed by the ICAO Committee on Aviation Environmental Protection (CAEP). This AC references specific Technical Manual equivalent procedures that may be considered acceptable by FAA for aircraft noise certification applications. The acceptability of an equivalent procedure for an aircraft noise certification application is subject to FAA review and approval on a project by project basis.

c. Document Format: This AC contains a section-by-section review of part 36 as shown in Figure 1:

FIGURE 1: Document Format

d. Exclusions: The following topics are not addressed in this AC:

(1) This document does not review the noise certification requirements for supersonic transport category airplanes. Part 36, Subpart D and other related sections of part 36, address supersonic airplane noise certification requirements only for the Concorde airplane and there currently are no identified procedures for future supersonic planes. An applicant must contact the FAA Office of Environment and Energy for assistance and future plans associated with the noise certification of supersonic transport category airplanes.

Paragraph Number: new easy to reference number for each section of 14 CFR part 36 that is addressed

1. Citation Number: Regulatory section of 14 CFR part 36 that is being addressed

1. Citation Number: Regulatory section of 14 CFR part 36 that is being addressed

Supplemental information (included only if necessary).

2. 286. Section B36.7(b)(6).

The weight of the airplane at the brake release must be the maximum takeoff weight at which the noise certification is requested….

a. Explanation

This section specifies criteria for defining a reference maximum takeoff weight of an airplane.

b. Supplemental Information

(1) Part 36 section 36.1581 Requirements: An airplane reference maximum takeoff weight for noise certification which is less than the maximum weight established under applicable airworthiness requirements must be furnished as operating limitations in the limitations section of the airplane flight manual.

c. Procedures:

(1) Applicant’s Responsibility: An applicant must define and obtain FAA approval of an airplane maximum takeoff weight to calculate reference EPNL values.

Actual regulatory text (italicized, bold and indented) reproduced for better readability Brief “Plain English” explanation of regulatory text (appears only if text is not self explanatory) Additional procedurerelated information (included only if necessary).

(2) This document does not review part 36 Appendix F, “Flyover Noise Requirements for Propeller-Driven Small Airplane and Propeller-Driven, Commuter Category Airplane Certification Tests Prior to December 22, 1988.” Appendix F has been superseded by Appendix G.

(3) This document does not review the aircraft operational limitations that may be imposed on certificated civil aircraft operating within the United States of America, such as is identified in part 91. An applicant or operator may review the current operational limitations that are found in the Operating Noise Limits of part 91, Subpart I, section 91.801.

e. 14 CFR part 36 History: The table below summarizes the date of adoption of part 36 and all amendments that followed.

Amendment #,

Effective Date

Title Subject

00-0, 12/01/69 Adoption of part 36 Adds new part 36 to the FAR and makes procedural changes to part 21. 36-1, 12/01/69 Approach Noise Test Conditions

Changes the type certification approach noise test conditions for subsonic transport category airplanes and for subsonic turbojet airplanes regardless of category; to ensure that the test is conducted with the same configuration as that used during the airworthiness type certification, and does not result in noise levels less than those that will be generated in normal operation. 36-2, 12/01/73 Noise Standards for Newly Produced Airplanes of Older Type Designs

Requires certain new production turbojet and transport category airplanes to comply with part 36, regardless of type certification date as a condition for issuance of certain standard airworthiness certificates. 36-3, 01/20/75 Acoustical Change Approvals

Tightens the conditions under which an applicant must show that issuance of type certificate changes will not increase take-off and sideline noise levels. 36-4, 02/07/75 Noise Standards for Propeller Driven Small Airplanes

Prescribes noise standards for normal, utility, acrobatic, transport, and restricted category type certificates for propeller driven small airplanes; issuance of standard airworthiness certificates and restricted category airworthiness certificates for newly produced propeller driven small airplanes of older type designs; prohibits acoustical changes in the type designs that increase noise levels beyond specified limits. 36-5, 09/20/76 Noise Type Certification and Acoustical Change Approvals

Changes the procedures for measuring and evaluating the noise of subsonic transport category airplanes and turbojet engine powered airplanes; governs new type certificates and acoustical change approvals for which application, is made after September 17, 1971. 36-6, 01/24/77 Noise Regulations for Propeller Driven Small Airplanes Submitted to the FAA by the EPA; and Notice of Decision

Changes procedures to increase the numbers of test flights, modify performance correction formula, and revise noise test engine power; decision not to make other certain EPA recommended amendments.

36-7, 10/01/77 Noise Level Limits and Acoustical Change

Provides for three stages of aircraft noise levels with specified limits, with definitions of classification of airplanes under each stage; applications after November 5, 1975 to be Stage 3;

Amendment #,

Effective Date

Title Subject

Requirements for Subsonic Transport Category Large Airplanes and for Subsonic Turbojet Powered Airplanes

prescribes acoustical change requirements for airplanes in each stage.

36-8, 04/03/78 Noise Limits and Acoustical Change Requirements for Subsonic Transport Category Large Airplanes and Turbojet Powered Airplanes

Amends noise limits for new airplane designs; limits noise levels of certain older airplane types if designs are changed; amends noise measuring points and noise test conditions; this amendment complements 36-7 and includes minor modifications to the Stage 3 noise limits, and also brings part 36 into greater conformity with ICAO standard.

36-9, 04/03/78 Aircraft Noise Measurement and Evaluation Specification

Updates and clarifies the procedures and standards for conducting certain aircraft noise certification tests, based on developments in the state of the art and on aircraft noise test experience; achieves substantial conformity with modifications to ICAO Annex 16. 36-10, 07/31/78 Civil Supersonic Airplanes Noise and Sonic Boom Requirements

Prescribes final rules for SSTs except Concordes with flight time before January 1, 1980; prohibits issuance of standard airworthiness certificates to Concordes that do not have flight time before January 1, 1980 and that do not comply with part 36; also amends part 21 and part 91 concerning operations of subject airplanes; FAA goal to not certificate or permit to operate any future design SST that does not meet standards then applicable to subsonic airplanes. 36-8, 09/28/78 CORRECTION

(Title): Correction to Minimum Thrust Cutback Altitudes

Prescribes the minimum altitude at which thrust may be reduced during take-off noise tests for certain airplanes powered by turbojet engines with high bypass ratios, which were previously certificated under the stage 2 limits; affects approvals for voluntary changes in type design which might increase the noise levels and is necessary to avoid an unintended effect of Amendment 36-8. 36-9, 01/15/79 CORRECTION

(Title): PNLT Corrections Formula for Ambient Atmosphere Conditions Affecting the Sideline Flight Path

Executes FAA's intended statement of the rule and prescribes an appropriate correction to the measured noise data when atmospheric conditions do not conform to the prescribed standard reference conditions.

36-11, 11/10/80 Operating Limitations and Related Requirements for Certain Propeller Driven Small Airplanes

Provides for certain exclusions from the rule; applies to operation of newly produced airplanes (without flight time before January 1, 1980), and acoustically changed airplanes (without flight time in the changed design before January 1, 1980), that have not been shown to comply with part 36 noise levels; requires that an operating limitation be appropriately provided to the pilot.

Amendment #,

Effective Date

Title Subject

Designed for Agricultural Aircraft Operations or Fire Fighting Purposes 36-12, 08/01/81 Noise Levels for Turbojet Engine Powered Airplanes and for Large Propeller Driven Airplanes: Recommended Regulations Submitted to the FAA by the EPA

Adds provision for FAA approval or equivalent procedures; clarifies and simplifies rule language to better explain which noise level requirements apply and which “tradeoff” provisions are available to applicants for approval of modifications to certain, already certificated aircraft type designs; FAA decisions not to prescribe other EPA recommended amendments.

36-13, 02/17/87 Airworthiness Standards and Operating Rules: Commuter Category Airplanes

Amends parts 21, 23, 36, 91, and 135 concerning an additional category of propeller driven, multi engine airplane designated as Commuter Category.

36-14, 2/05/88 Noise Standards for Helicopters in the Normal, Transport and Restricted Categories

Adds noise certification Standards applicable to helicopters; applies to civil helicopters in the normal, transport and restricted categories and provides noise level limits and test procedures for the issuance of original and amended type certificates; prohibits changes in type design of helicopters that may increase noise levels beyond certain limits; does not limit further manufacture of existing helicopter types; provides commonality with ICAO Annex 16. 36-15, 05/06/88 Standards Governing the Noise Certification of Aircraft

Revises certain provisions of the regulations to make them more understandable and easier to use; simplifies noise certification test and record keeping requirements. 36-16, 12/22/88 Noise Certification Standards for Propeller Driven Small Airplanes

Revises noise certification standard by substituting the use of actual take-off tests for the level flyover tests; revises the noise level limit numbers to approximate the sound levels measured in accordance with Appendix F of part 36; exempts both antique airplanes and airplanes modified by the addition of floats and skis from the acoustical change measurement and documentation requirements of part 21. 36-17, 08/14/89 Noise Standards; Limits on the Growth of Noise from Certain Airplanes and Airplane Types

Requires that aircraft certificated within certain stages remain within those stages; applies to large transport category aircraft and to turbojet powered aircraft regardless of category and prohibits modification of individual airplanes and whole airplane types which result in increased noise beyond the limits of an airplane's certificated stage; does not restrict changes that result in decreased noise but does prohibit any remodification of an airplane which would return it to its original noise level. 36-18, 08/18/90 Revision of General Operating and Flight Rules

Reorganizes and realigns the rules to make them more understandable and easier to use; provides more flexibility for certain operations. 36-19, 12/31/92 Primary Category Establishes a new primary category of aircraft and new simplified procedures for type, production, and airworthiness certification, and

Amendment #,

Effective Date

Title Subject

associated maintenance procedures; maximum certificated weight of no more than 2,700 pounds, a maximum seating capacity of four, and unpressurized cabins. 36-20, 09/11/92 Alternative Noise Certification for Primary, Normal, Transport and Restricted Category Helicopters not Exceeding 6,000 Pounds Maximum Take-off Weight

Adds Appendix J to part 36 providing for an alternative noise certification procedure; new appendix is an optional alternative to the existing helicopter noise requirements and is not an additional regulatory requirement; applicants may demonstrate compliance with either Appendix H or the less costly, but more stringent Appendix J.

36-21, 12/29/95 Authority Citation Revises part 36 authority citation. 36-22, 12/13/99 Noise Certification Standards for Propeller-Driven Small Airplanes

Harmonizes the U.S. noise certification regulations and the European Joint Aviation Requirements (JAR) for propeller-driven small airplanes. The international standards and practices, as issued under International Civil Aviation Organization (ICAO) Annex 16, Volume 1, and its associated Technical Manual are the harmonization basis. 36-23, 3/1/2002 Removal of Expired Special Federal Aviation Regulations

Removes Special Federal Aviation Regulation (SFAR) Number 41 editorial note from part 36.

36-24, 8/7/2002 Noise Certification Standards for Subsonic Jet Airplanes and Subsonic Transport Category Large Airplanes

Harmonizes the U.S. noise certification regulations and the European Joint Aviation Requirements (JAR) for subsonic jet airplanes and subsonic transport category large airplanes. The international standards and practices, as issued under International Civil Aviation Organization (ICAO) Annex 16, Volume 1 (Chapter 3), Amendment 7, and its associated Technical Manual are the harmonization basis.

2. CANCELLATION. Advisory Circular 36-4B, Noise Certification Handbook, dated March 23, 1988, is canceled. 3. REFERENCES.

The following references identify FAA Orders, Advisory Circulars, and Reports that provide direction and/or guidance on acceptable processes and procedures for aircraft noise certification. References to current ICAO and JAA noise standards are also listed. As these documents are referenced in this AC, information is also provided as to the extent that their provisions apply to a given type of aircraft noise certification process. Applicants are encouraged to contact FAA AEE to determine if more recent editions are available and applicable to noise certification actions that are being considered for FAA approval.

(1) FAA Order 1050.1D, Policies and Procedures For Considering Environmental Impacts, (Change 4, June 14, 1999), or current version (2) Public Law 103-272, Codification of Certain U.S. Transportation Laws as Title 49, United States Code, Section 44715, July 5, 1994

(3) Part 36, Appendix G Handbook, FAA Report FAA-AEE-95, dated June 20, 1995

(4) Requirements for DGPS-Based TSPI Systems Used in Aircraft Noise Certification Tests, DTS-75- FA753-LR3, Letter Report, April 14, 1997

(5) Joint Aviation Requirements, JAR 36, Aircraft Noise, May 1997 (6) Advisory Circular (AC) 25-7A, Flight Test Guide, March 31, 1998, or current version (7) FAA Order 8110.4B, Type Certification Process, April 24, 2000, or current version (8) ICAO Committee on Aviation Environmental Protection (CAEP), Environmental Technical Manual on the Use of Procedures in the Noise Certification of Aircraft, Steering Group Approved Revision (SGAR) 7, September 2000 (included as Appendix 1 to this AC) (9) FAA Order 8100.8A, Designee Management Handbook, January 30, 2001, or current version (10) FAA Order 8110.37C, September 30, 1998. Designated Engineering Representatives (DER) Guidance Handbook, or current version

(11) International Civil Aviation Organization (ICAO), Environmental Protection, Annex 16, Volume 1, Aircraft Noise, Third Edition - 1993. (Amendment 7, Applicable March 21, 2002) 4. DEFINITIONS.

This section contains two categories of Definitions that are used within the regulatory language, policies or other guidance information of this Advisory Circular. The first category defines general terms or organizational designations that depict FAA and Applicant roles in the part 36 noise certification process. The second category defines specific aircraft types that must comply with part 36 regulations and other items related to those aircraft.

a. General Definitions:

(1) Administrator: The Federal Aviation Administrator or any person to whom he has delegated his authority in the matter concerned. (Ref: part 1)

(2) Aircraft Certification Office (ACO): The (FAA) office that administers the type certificate and production approval of products in the area where the manufacturer is located (Ref: FAA AC 21-6A, dated 7/1/82)

(3) Applicant: 14 CFR part 21.13, states: “Any interested person may apply for a type certificate”. The person that applies to the FAA for an aircraft type certificate, whether a new (original), amended, supplemental or provisional type certificate, is identified as the “applicant” and is the entity that must comply with the procedural, certification and production requirements of 14 CFR part 21.

(4) Noise Certification Specialist (NCS): The Directorate (Transport, Small Airplane, or Helicopter) Noise Certification Specialist

(5) Person: An individual, firm, partnership, corporation, company, association, joint-stock association, or government entity. It includes a trustee, receiver, assignee, or similar representative of any of them. (Ref: part 1)

(6) Type Inspection Authorization (TIA): The TIA is the official FAA document that provides direction and communication between the local ACO engineering group and the FAA flight test crew. The TIA usually mandates the provisions of an applicant’s approved demonstration compliance plan and any additional restrictions, inspections, tests, limitations, procedures, etc., that are required by the ACO to be observed during the conduct of the flight or ground testing.

b. Definitions Related to Aircraft

(1) Acrobatic Category Airplane: The acrobatic category is limited to airplanes that have a seating configuration, excluding pilot seats, of nine or less, a maximum certificated take-off weight of 12,500 pounds or less, and intended for use without restrictions, other than those shown to be necessary as a result of required flight tests. Acrobatic category airplanes are required to show compliance with 14 CFR part 23.

(2) Aircraft: A device that is used or intended to be used for flight in the air. (Ref: part 1) (3) Aircraft Engine: An engine that is used, or intended to be used, for propelling aircraft. It includes turbosuperchargers, appurtenances, and accessories necessary for its functioning, but does not include propellers. (Ref: part 1)

(4) Airplane: An engine-driven fixed-wing aircraft heavier than air that is supported in flight by the dynamic reaction of the air against its wings. (Ref: part 1)

(5) Airport: An area of land or water that is used or intended to be used for the landing and take-off of aircraft, and includes its buildings and facilities, if any. (Ref: part 1)

(6) Civil Aircraft: Aircraft other than a public aircraft. (Ref: part 1) (7) Commuter Category Airplanes: The commuter category is limited to propeller-driven, multiengine airplanes that have a seating configuration, excluding pilot seats, of 19 or less, and a maximum certificated takeoff weight of 19,000 pounds or less, intended for non-acrobatic operations. Commuter category airplanes are required to show compliance with part 23.

(8) Helicopter: A rotorcraft that, for its horizontal motion, depends principally on its engine-driven rotors. (Ref: part 1)

(9) Large Aircraft: Large aircraft means aircraft of more than 12,500 pounds, maximum certificated takeoff weight (Ref: part 1)

(10) Normal Category Airplane: The normal category is limited to airplanes that have a seating configuration, excluding pilot seats, of nine or less, a maximum certificated take-off weight of 12,500 pounds or less, and intended for nonacrobatic operation. Normal category airplanes are required to show compliance with 14 CFR part 23. (11) Normal Category Rotorcraft: A normal category rotorcraft is a rotorcraft with a maximum weight of 7,000 pounds or less and that meets the regulatory requirements of part 27. (12) Primary Category Aircraft: A primary category aircraft is an aircraft that (i) is unpowered, or is an airplane powered by a single, naturally aspirated engine with a 61-knot or less stall speed, or is a rotorcraft with a 6-pound per square foot main rotor disc loading limitations, and (ii) weighs not more than 2,700 pounds, and (iii) has a maximum seating capacity of not more than four persons, including the pilot, and (iv) has an unpressurized cabin. A primary category aircraft is required to meet the regulatory requirements of part 21, section 21.24.

(13) Propeller: A device for propelling an aircraft that has blades on an engine-driven shaft and that, when rotated, produces by its action on the air, a thrust approximately perpendicular to its plane of rotation. It includes control components normally supplied by its manufacturer, but does not include main and auxiliary rotors or rotating airfoils of engines. (Ref: part 1).

(14) Public Aircraft: Aircraft used only in the service of a government, or a political subdivision. It does not include any government-owned aircraft engaged in carrying persons or property for commercial purposes. (Ref: part 1)

(15) Restricted Aircraft: Used for special purpose operations as defined in part 21, section 21.25 (16) Rotorcraft: A heavier-than-air aircraft that depends principally for its support in flight on the lift generated by one or more rotors (Ref: 14 CFR part 1).

(17) Small Aircraft: Small aircraft means aircraft of 12,500 pounds or less, maximum certificated take-off weight. (Ref: part 1)

(18) Subsonic airplane: A subsonic airplane means an airplane for which the maximum operating limit speed, MMO, does not exceed a Mach number of 1.

(19) Supersonic airplane: A supersonic airplane means an airplane for which the maximum operating limit speed, MMO, exceeds a Mach number of 1.

(20) Transport Category Aircraft: Those aircraft (large or small) that are demonstrated to meet and are certificated to the regulatory requirements of part 25 for transport category airplanes or part 29 for transport category rotorcraft.

(21) Jet Airplane: Any fixed wing airplane that is powered by a turbojet or turbofan engine regardless of whether it is an airplane certificated to part 23 (small or commuter aircraft) or part 25 (transport category aircraft)

(22) Turbo-propeller Airplane: An airplane whose primary source of thrust is from a propeller driven by a gas turbine engine.

(23) Utility Category Airplane: The utility category is limited to airplanes that have a seating configuration, excluding pilot seats, of nine or less, a maximum certificated take-off weight of 12,500 pounds or less, and intended for limited acrobatic operation. Utility category airplanes are required to show compliance with part 23.

5. ABBREVIATION AND ACRONYMS.

Note: In addition to the abbreviations and acronyms contained in this paragraph, section A36.6 of this AC contains symbols and units associated with the noise certification standards for subsonic transport category large airplanes and jet airplanes.

AC = FAA Advisory Circular A/C = Air-conditioning (Environmental Control System) ACO = Local FAA Aircraft Certification Office AEE = FAA Office of Environment and Energy AFM = Airplane Flight Manual ANM = FAA Northwest Mountain Region APU = Auxiliary Power Unit ARP = Aerospace Recommended Practice CDI = Course Deviation Indicator CG = Center of Gravity CFR = Code of Federal Regulations dB = decibels DER = Designated Engineering Representative DGPS = Differential Global Positioning System DMU = Distance Measuring Unit EPR = Engine Pressure Ratio (Power Setting Parameter) FAA = Federal Aviation Administration GDI = Glide-slope Deviation Indicator GPS = Global Positioning System Hz = oscillatory frequency, cycles per second

INS = Inertial Navigation System ICAO = International Civil Aviation Organization ILS = Instrument Landing System ISA = International Standard Atmosphere JAR = Joint Aviation Requirements (of Europe) Log = logarithmic value to base 10 m = meter MLW = Maximum Landing Weight MSL = Mean Sea Level altitude, feet MTOGW = Maximum Take-off Gross Weight N1 = Low Pressure Rotor Speed (Power Setting Parameter), rpm or % NAC = No Acoustical Change NCS = Noise Certification Specialist NIST = National Institute of Standards and Technology NPD = Noise-Power-Distance RFM = Rotorcraft Flight Manual RH = Relative Humidity, % rms = root-mean-square rpm = revolutions per minute SAE = Society of Automotive Engineers SBV = Surge Bleed Valve (engine internal operating valves) STC = Supplemental Type Certificate TIA = Type Inspection Authorization TC = Type Certificate TM = Technical Manual (“ICAO Environmental Technical Manual on the use of Procedures in the Noise

Certification of Aircraft”) TSPI = Time Space Positional Information VNTSC = Volpe National Transportation System Center (DOT) VREF = Reference Landing Speed 6. - 7. RESERVED.

TABLE OF CONTENTS 1. PURPOSE … 1 2. CANCELLATION … 6 3. REFERENCES … 6 4. DEFINITIONS … 7 5. ABBREVIATION AND ACRONYMS … 9 6. - 7. RESERVED … 10 I. CERTIFICATION PROCEDURES FOR PRODUCT AND PARTS 14 CFR PART 21 … 19 8. PART 21 - GENERAL … 19 9.-11. [RESERVED] … 19 II. NOISE STANDARDS: AIRCRAFT TYPE AND AIRWORTHINESS CERTIFICATION 14 CFR PART 36 … 20 12. PART 36 – SUBPART A-GENERAL … 20 13. Section 36.1 Applicability and definitions … 20 14. Section 36.1(a) … 20 15. Section 36.1(b) … 21 16. Section 36.1(c) … 22 17. Section 36.1(d) … 24 18. Section 36.1(e) … 25 19. Section 36.1(f) … 26 20. Section 36.1(g) … 26 21. Section 36.1(h) … 27 22. Section 36.2 Requirements as of date of application … 28 23. Section 36.3 Compatibility with airworthiness requirements … 29 24. Section 36.5 Limitation of part … 29 25. Section 36.6 Incorporations by reference … 30 26. Section 36.6(a) … 30 27. Section 36.6(b) … 30 28. Section 36.6(c) … 31 29. Section 36.6(d) … 31 30. Section 36.6(e) … 32 31. Section 36.7 Acoustical Change: Transport category large airplanes and jet airplanes … 37 32.

Section 36.7(a) … 37 33. Section 36.7(b) … 37 34. Section 36.7(c) … 38 35. Section 36.7(d) … 39 36. Section 36.7(e) … 39 37. Section 36.9 Acoustical change: Propeller-driven small airplanes and propeller-driven commuter category airplanes [To be completed later] … 40 38. Section 36.9(a) [To be completed later] … 40 39. Section 36.9(b) [To be completed later] … 40 40. Section 36.11 Acoustical Change: Helicopters … 40 41. Section 36.11(a) … 40 42. Section 36.11(b) … 41 43. Section 36.11(c) … 42 44. – 50. RESERVED … 42 III. SUBPART B— TRANSPORT CATEGORY LARGE AIRPLANES AND JET AIRPLANES … 43 51. Section 36.101 Noise measurement and evaluation … 43 52. Section 36.103 Noise limits … 44 53. Section 36.103(a) … 45 54. Section 36.103(b) … 45 IV. SUBPART C—RESERVED … 46 V. SUBPART D—NOISE LIMITS FOR SUPERSONIC TRANSPORT CATEGORY AIRPLANES … 47 55. Section 36.301 Noise limits: Concorde … 47 56. Section 36.301(a) … 47

57. Section 36.301(b) … 47 VI. SUBPART E--[RESERVED] … 48 VII. SUBPART F--PROPELLER-DRIVEN SMALL AIRPLANES AND PROPELLER-DRIVEN, COMMUTER CATEGORY AIRPLANES … 49 58. Section 36.501 Noise Limits … 49 59. Section 36.501(a) … 49 60. Section 36.501(b) … 49 61. Section 36.501(c) … 49 VIII. SUBPART G--[RESERVED] … 50

62. -65 [RESERVED] … 50 IX. SUBPART H--HELICOPTERS … 51 66. Section 36.801 Noise measurement [To be completed later] … 51 67. Section 36.803 Noise evaluation and calculation [To be completed later] … 51 68. Section 36.805 Noise limits [To be completed later] … 51 69. Section 36.805(a) [To be completed later] … 51 70. Section 36.801(b) [To be completed later] … 51 71. Section 36.805(c) … 51 72. Section 36.805(d) [To be completed later] … 52 X. SUBPARTS I--N [RESERVED] … 53 73. –75 [RESERVED] … 53 XI. SUBPART E--RESERVED … 54 XII. SUBPART O--OPERATING LIMITATIONS AND INFORMATION … 55 76. Section 36.1501 Procedures, noise levels and other information … 55 77. Section 36.1501(a) … 55 78. Section 36.1501(b) … 61 79. Section 36.1581 Manuals, markings, and placards … 62 80. Section 36.1581(a) … 62 81. Section 36.1581(b) … 64 82. Section 36.1581(c) … 65 83. Section 36.1581(d) … 65 84. Section 36.1581(e) … 66 85. Section 36.1581(f) … 66 86. Section 36.1581(g) … 66 87. Section 36.1583 Noncomplying agricultural and fire fighting airplanes … 66 88. Section 36.1583(a) … 66 89. Section 36.1583(b) … 67 90. - 99 [RESERVED] … 68 XIII. APPENDIX A TO Part 36-AIRCRAFT NOISE MEASUREMENT AND EVALUATION UNDER §

36.101 69 100. Appendix A to Part 36-Aircraft Noise Measurement and Evaluation Under § 36.101 … 69 101. Section A36.1 Introduction … 69 102. Section A36.1.1 … 69 103. Section A36.1.2 … 69 104. Section A36.1.3 … 69 105. Section A36.2. Noise certification test and measurement conditions … 69 106. Section A36.2.1 General … 69 107. Section A36.2.1.1 … 70 108. Section A36.2.2 Test environment … 70 109. Section A36.2.2.1 … 70 110. Section A36.2.2.2 … 71 111. Section A36.2.2.2(a) … 72 112. Section A36.2.2.2(b) … 72 113. Section A36.2.2.2(c) … 73 114. Section A36.2.2.2(d) … 74 115. Section A36.2.2.2(e) … 75

116. Section A36.2.2.2(f) … 76 117. Section A36.2.2.2(g) … 77 118. Section A36.2.2.3 … 77 119. Section A36.2.2.4 … 79 120. Section A36.2.3 Flight path measurement … 80 121. Section A36.2.3.1 … 80 122. Section A36.2.3.2 … 81 123. Section A36.2.3.3 … 83 124. Section A36.3 Measurement of Airplane Noise Received on the Ground … 83 125. Section A36.3.1 Definitions … 84 126. Section A36.3.1.1 … 84 127. Section A36.3.1.2 … 84 128. Section A36.3.1.3 … 84 129. Section A36.3.1.4 … 84 130. Section A36.3.1.5 … 84 131. Section A36.3.1.6 … 84 132. Section A36.3.1.7 … 85 133. Section A36.3.1.8 … 85 134. Section A36.3.1.9 … 85 135. Section A36.3.1.10 … 85 136. Section A36.3.1.11 … 85 137. Section A36.3.1.12 … 85 138. Section A36.3.1.13 … 85 139. Section A36.3.1.14 … 85 140. Section A36.3.1.15 … 85 141. Section A36.3.1.16 … 86 142. Section A36.3.2 Reference environmental conditions … 86 143. Section A36.3.2.1 … 86 144. Section A36.3.3 General … 86 145. Section A36.3.3.1 … 87 146. Section A36.3.3.2 … 88 147. Section A36.3.4 Windscreen … 88 148. Section A36.3.4.1 … 88 149.

Section A36.3.5 Microphone system … 88 150. Section A36.3.5.1 … 88 151. Section A36.3.5.2 … 88 152. Section A36.3.5.3 … 89 153. Section A36.3.5.4 … 89 154. Section A36.3.6 Recording and reproducing systems … 91 155. Section A36.3.6.1 … 91 156. Section A36.3.6.2 … 91 157. Section A36.3.6.3 … 91 158. Section A36.3.6.4 … 92 159. Section A36.3.6.5 … 92 160. Section A36.3.6.6 … 92 161. Section A36.3.6.7 … 92 162. Section A36.3.6.8 … 92 163. Section A36.3.6.9 … 92 164. Section A36.3.7 Analysis systems … 94 165. Section A36.3.7.1 … 94 166. Section A36.3.7.2 … 94 167. Section A36.3.7.3 … 94 168. Section A36.3.7.4 … 94 169. Section A36.3.7.5 … 95 170. Section A36.3.7.6 … 95

171. Section A36.3.7.7 … 95 172. Section A36.3.8 Calibration systems … 96 173. Section A36.3.8.1 … 96 174. Section A36.3.9 Calibration and checking of system … 96 175. Section A36.3.9.1 … 96 176. Section A36.3.9.2 … 96 177. Section A36.3.9.3 … 97 178. Section A36.3.9.4 … 97 179. Section A36.3.9.5 … 97 180. Section A36.3.9.6 … 97 181. Section A36.3.9.7 … 97 182. Section A36.3.9.8 … 97 183. Section A36.3.9.9 … 98 184. Section A36.3.9.10 … 98 185. Section A36.3.10 Adjustments for ambient noise … 100 186. Section A36.3.10.1 … 100 187. Section A36.3.10.2 … 101 188. Section A36.4 Calculation of Effective Perceived Noise Level From Measured Data … 101 189. Section A36.4.1 General … 101 190. Section A36.4.1.1 … 101 191. Section A36.4.1.2 … 101 192. Section A36.4.1.3 … 101 193. Section A36.4.2 Perceived noise level … 102 194. Section A36.4.2.1 … 102 195. Section A36.4.3 Correction for spectral irregularities … 103 196. Section A36.4.3.1 … 103 197. Section A36.4.3.2 … 108 198. Section A36.4.4 Maximum tone-corrected perceived noise level … 109 199. Section A36.4.4.1 … 109 200.

Section A36.4.4.2 … 110 201. Section A36.4.5 Duration correction … 110 202. Section A36.4.5.1 … 110 203. Section A36.4.5.2 … 111 204. Section A36.4.5.3 … 111 205. Section A36.4.5.4 … 111 206. Section A36.4.5.5 … 112 207. Section A36.4.6 Effective perceived noise level … 112 208. Section A36.4.6 … 112 209. Section A36.4.7 Mathematical formulation of noy tables … 113 210. Section A36.4.7.1 … 113 211. Section A36.4.7.2 … 113 212. Section A36.4.7.3 Calculate noy values using the following equations: … 113 213. Section A36.4.7.4 … 113 214. Section A36.5. Reporting of Data to the FAA … 117 215. Section A36.5.1 General … 117 216. Section A36.5.1.1 … 117 217. Section A36.5.1.2 … 117 218. Section A36.5.1.3 … 117 219. Section A36.5.2 Data reporting … 117 220. Section A36.5.2.1 … 118 221. Section A36.5.2.2 … 118 222. Section A36.5.2.3 … 118 223. Section A36.5.2.4 … 118 224. Section A36.5.2.5 … 118 225. Section A36.5.3 Reporting of noise certification reference conditions … 119

226. Section A36.5.3.1 … 119 227. Section A36.5.4 Validity of results … 119 228. Section A36.5.4.1 … 120 229. Section A36.5.4.2 … 120 230. Section A36.5.4.3 … 120 231. Section A36.6 Nomenclature: Symbols and Units … 123 232. Section A36.7 Sound Attenuation in Air … 127 233. Section A36.7.1 … 127 234. Section A36.7.2 … 127 235. Section A36.7.3 … 129 236. Section A36.8. [Reserved] … 130 237. Section A36.9. Adjustment of Airplane Flight Test Results … 130 238. Section A36.9.1 … 130 239. Section A36.9.1.1 … 131 240. Section A36.9.1.2 … 133 241. Section A36.9.2 Flight profiles … 134 242. Section A36.9.2.1 Takeoff Profile … 134 243. Section A36.9.2.2 Approach Profile … 141 244. Section A36.9.3 Simplified method of adjustment … 145 245. Section A36.9.3.1 General … 145 246. Section A36.9.3.2 Adjustments to PNL and PNLT … 146 247. Section A36.9.3.2.1 … 148 248. Section A36.9.3.2.1.1 PNLT Correction … 150 249. Section A36.9.3.2.1.2 … 150 250. Section A36.9.3.2.2 … 150 251. Section A36.9.3.3 Adjustments to duration correction … 151 252. Section A36.9.3.3.1 … 151 253.

Section A36.9.3.3.2 … 151 254. Section A36.9.3.4 Source noise adjustments … 152 255. Section A36.9.3.4.1 … 152 256. Section A36.9.3.4.2 … 152 257. Section A36.9.3.5 Symmetry Adjustments … 152 258. Section A36.9.3.5.1 … 152 259. Section A36.9.4 Integrated method of adjustment … 153 260. Section A36.9.4.1 General … 153 261. Section A36.9.4.2 PNLT computations … 154 262. Section A36.9.4.2.1 … 157 263. Section A36.9.4.2.2 … 158 264. Section A36.9.4.2.3 … 158 265. Section A36.9.4.3 Duration correction … 158 266. Section A36.9.4.3.1 … 158 267. Section A36.9.4.4 Source noise adjustment … 158 268. Section A36.9.4.4.1 … 158 269. Section A36.9.5 Flight Path Identification Positions … 159 270. Section A36.9.6 Flight Path Distances … 159 271. - 289--RESERVED … 160 XIV. APPENDIX B TO part 36--NOISE LEVELS FOR TRANSPORT CATEGORY AND JET

AIRPLANES UNDER § 36.103 … 161 290. Appendix B to Part 36-Noise Levels for Transport Category and Jet Airplanes Under § 36.103 161 291. Section B36.1 Noise Measurement and Evaluation … 161 292. Section B36.2 Noise Evaluation Metric … 161 293. Section B36.3 Reference Noise Measurement Points … 162 294. Section B36.4 Test noise measurement points … 162 295. Section B36.5 Maximum Noise Levels … 163 296. Section B36.6 Trade-Offs … 165

297. Section B36.7 Noise Certification Reference Procedures and Conditions … 166 298. Section B36.7(a) General conditions: … 166 299. Section B36.7(b) Takeoff reference procedure: … 167 300. Section B36.7(b)(1) … 167 301. Section B36.7(b)(2) … 168 302. Section B36.7(b)(3) … 168 303. Section B36.7(b)(4) … 169 304. Section B36.7(b)(5) … 169 305. Section B36.7(b)(6) … 170 306. Section B36.7(b)(7) … 170 307. Section B36.7(c) Approach reference procedure: … 171 308. Section B36.7(c)(1) … 171 309. Section B36.7(c)(2) … 171 310. Section B36.7(c)(3) … 171 311. Section B36.7(c)(4) … 172 312. Section B36.7(c)(5) … 173 313. Section B36.8 Noise Certification Test Procedures … 173 314. Section B36.8(a) … 173 315. Section B36.8(b) … 174 316. Section B36.8(c) … 174 317. Section B36.8(d) … 174 318. Section B36.8(e) … 175 319. Section B36.8(f) … 175 320. Section B36.8(g) … 175 321. - 349. [RESERVED] … 176 XV. 14 CFR PART 36 APPENDIX F. FLYOVER NOISE REQUIREMENTS FOR PROPELLER -

DRIVEN SMALL AIRPLANE AND PROPELLER-DRIVEN, COMMUTER CATEGORY AIRPLANE CERTIFICATION TESTS PRIOR TO DECEMBER 22, 1988 … 177 350. PART A - GENERAL … 177 351. Section F36.1 Scope [To be completed later.] … 177 352. PART B - NOISE MEASUREMENT … 177 353. Section F36.101 General Test Conditions [To be completed later.] … 177 354. Section F36.103 Acoustical Measurement System [To be completed later.] … 177 355. Section F36.105 Sensing, Recording, and Reproducing Equipment … 177 356. Section F36.107 Noise Measurement Procedures [To be completed later.] … 177 357. Section F36.109 Data Recording, Reporting, and Approval [To be completed later … 177 358. Section F36.111 Flight Procedures [To be completed later.] … 177 359. PART C - DATA CORRECTION … 177 360. Section F36.201 Correction of Data [To be completed later.] … 177 361. Section F36.203 Validity of Results [To be completed later.] … 177 362. PART D - NOISE LIMITS … 177 363. Section F36.301 Aircraft Noise Limits [To be completed later.] … 177 364. - 374. [RESERVED] … 177 XVI. 14 CFR PART 36 APPENDIX G. TAKE-OFF NOISE REQUIREMENTS FOR PROPELLER-

DRIVEN, SMALL AIRPLANE AND PROPELLER-DRIVEN, COMMUTER CATEGORY AIRPLANE CERTIFICATION TESTS ON OR AFTER DECEMBER 22, 1988 … 178 375. PART A - GENERAL … 178 376. Section G36.1 Scope … 178 377. PART B - NOISE MEASUREMENT … 178 378. Section G36.101 General test conditions … 178 379. Section G36.101(b) … 179 380. Section G36.101(c) … 181 381. Section G36.101(d) … 182 382. Section G36.103 Acoustical measurement system … 182 383. Section G36.103(b) & (c) … 182

384. Section G36.103(d) … 183 385. Section G36.105(a) … 184 386. Section G36.105(b)&(c) … 184 387. Section G36.105(d) … 185 388. Section G36.105(e) … 186 389. Section G36.105(f) … 187 390. Section G36.105(g) … 187 391. Section G36.107 Noise measurement … 188 392. Section G36.107(b) … 190 393. Section G36.107(c) … 191 394. Section G36.109 Data Recording, Reporting and Approval … 192 395. Section G36.109(b) … 193 396. Section G36.109(c) & (d) … 193 397. Section G36.109(e) … 194 398. Section G36.109(f) … 194 399. Section G36.109(g) … 194 400. Section G36.111 Flight procedures … 195 401. Section G36.111(b) … 196 402. Section G36.111(c) … 196 403. Section G36.111(c)(1) … 197 404. Section G36.111(c)(2) … 198 405. PART C - DATA CORRECTION … 199 406. [RESERVED] … 199 407. Section G36.201 Correction of Data … 199 408. Section G36.201(b) … 200 409. Section G36.201(c) … 201 410. Section G36.201(d) … 201 411. Section G36.201(d)(1) … 202 412. Section G36.201(d)(2) … 203 413. Section G36.201(d)(3) … 204 414. Section G36.201(d)(4) … 206 415. Section G36.203 Validity of Results … 208 416. PART D - NOISE LIMITS … 209 417. Section G36.301 Aircraft Noise Limits … 209 418. −429. [RESERVED] … 210 XVII. 14 CFR PART 36 APPENDIX H- NOISE REQUIREMENTS FOR HELICOPTERS UNDER SUB-

PART H [To be completed later] … 211 XVIII. 14 CFR PART 36 APPENDIX J- ALTERNATIVE NOISE CERTIFICATION PROCEDURE FOR

HELICOPTERS UNDER SUBPART H HAVING A MAXIMUM CERTIFICATED TAKE-OFF WEIGHT OF NOT MORE THAN 6,000 POUNDS [To be completed later] … 211

APPENDICES APPENDIX 1 – ICAO Committee on Aviation Environmental Protection - Environmental Technical Manual On The

Use Of Procedures In The Noise Certification Of Aircraft, Steering Group Approved Revision 7 APPENDIX 2 – VNTSC Certification Validation Package APPENDIX 3 – Guidelines for Correction of Aircraft Noise Levels for the Effects of Background Noise APPENDIX 4 – Equivalent Procedures and Demonstrating "No Acoustical Change” for Propeller-Driven Small

Airplanes and Commuter Category Airplanes FIGURES FIGURE 1 Document Format FIGURE 2 Noise Time History with Thrust (Power) Reduction FIGURE 3 Normal Full Thrust (Power) Take-Off FIGURE 4 Flight Path Intercept Take-off FIGURE 5 Take-off Flight Path FIGURE 6 Approach With Full Landing FIGURE 7 Flight Path Intercept Approach FIGURE 8 Approach Flight Path Deviations FIGURE 9-12 RESERVED FIGURE 13 Configuration for 1/2 in. Inverted Microphone Over Plate FIGURE 14 Graphic Representation of Adjusted Measurement Location FIGURE 15 Typical Test and Reference Flight Paths FIGURE 16 Obstruction Free Noise Measurement Cone (Flyover Case Illustrated) FIGURE 17 Temperature/Relative Humidity Test Window (Note: The figures identified in the above list were developed for AC 36-4C. Figures contained within part 36 itself have not been included in this list.) TABLES TABLE 1 Example - Atmospheric Measurements TABLE 2 Example - Atmospheric Measurements TABLE 3 Example – Atmospheric Sound Attenuation Coefficients TABLE 4 Example – Effective Layer Depth TABLE 5 Rate of Atmospheric Absorption (α) at 500 Hz Frequency TABLE 6 Student’s t Distribution For 90 Percent Confidence Interval (Note: The tables identified in the above list were developed for AC 36-4C. Tables contained within part 36 itself have not been included in this list.)

8. PART 21 - GENERAL

8. PART 21 - GENERAL

As part of the overall aircraft certification requirements identified in part 21, applicants must comply with the noise certification requirements of part 36. An applicant for a type certificate must show that the aircraft meets the applicable requirements of part 36 (part 21, section 21.17). In addition, an applicant is entitled to a type certificate for an aircraft if the applicant submits the type design, test reports, and computations necessary to show that the product to be certificated meets the applicable airworthiness and aircraft noise requirements (part 21, sections 21.21 & 21.25). Similar requirements are imposed for aircraft manufactured in a foreign country for import into the United States (part 21, section 21.29). Refer to the part 21 regulations for specific regulatory language.

a. Explanation

None b. Supplemental Information

(1) Airworthiness Certification: All aircraft requiring noise certification by the FAA are required to meet the applicable airworthiness requirements of part 21, which identifies the specific airworthiness standards for each aircraft type and product, such as:

i. Part 23 for normal, utility, acrobatic, and commuter category airplanes, ii. Part 25 for transport category airplanes, iii. Part 27 for normal category rotorcraft, iv. Part 29 for transport category rotorcraft, v. Part 33 for aircraft engines,

vi. Part 35 for propellers, vii. Primary category aircraft, and viii. JAR-VLA aircraft.

(2) Changes in Type Design. Part 21 section 21.93(b) requires compliance with the appropriate part 36 “acoustical change” requirements for a voluntary type design change of an aircraft that may increase the noise levels of that aircraft, regardless of whether the change in type design is classified as a minor or major change in part 21, section 21.93(a). See paragraph 16 of this AC for further discussion of acoustical change. 9.-11. [RESERVED]

I. CERTIFICATION PROCEDURES FOR PRODUCT AND PARTS 14 CFR PART 21

I. CERTIFICATION PROCEDURES FOR PRODUCT AND PARTS 14 CFR PART 21

12. PART 36 – SUBPART A-GENERAL

a. Explanation

This Subpart specifies the Applicability of part 36, Definitions of Terms Unique to part 36, part 36 Requirements as of the Date of Type Certificate Application, Airworthiness Compatibility requirements, Limitations, Information on References, and Acoustical Change Requirements.

12. PART 36 – SUBPART A-GENERAL

b. Supplemental Information

None

c. Procedures

None 13. Section 36.1 Applicability and definitions 14. Section 36.1(a)

This part prescribes noise standards for the issue of the following certificates: (1) Type certificates, and changes to those certificates, and standard airworthiness certificates, for subsonic transport category large airplanes and for subsonic jet airplanes regardless of category.

(2) Type certificates and changes to those certificates, standard airworthiness certificates, and restricted category airworthiness certificates, for propeller-driven, small airplanes, and for propeller- driven, commuter category airplanes except those airplanes that are designed for "agricultural aircraft operations" (as defined in § 137.3 of this chapter, as effective on January 1, 1966) or for dispersing fire fighting materials to which § 36.1583 of this part does not apply.

(3) A type certificate and changes to that certificate, and standard airworthiness certificates, for Concorde airplanes.

(4) Type certificates, and changes to those certificates, for helicopters except those helicopters that are designated exclusively for "agricultural aircraft operations" (as defined in § 137.3 of this chapter, as effective on January 1, 1966), for dispensing fire fighting materials, or for carrying external loads (as defined in § 133.1(b) of this chapter, as effective on December 20, 1976).

a. Explanation

This section specifies aircraft types and categories to which part 36 requirements are applicable as a condition for issuance of type certificates (TC), changes to type certificates, supplemental type certificates (STC), amended type certificates and airworthiness certificates.

b. Supplemental Information

(1) Applicable Requirements: Unless otherwise specified, the date to be used for determining the applicability of the appropriate part 36 standards for an aircraft type design is the date on which application for a type certificate was made. An application for type certification is effective for the time periods specified in section 21.17(c) of part 21. (2) Noise Related Type Certification Requirements: See paragraph 6-3(h) of reference 7 of this AC.

II. NOISE STANDARDS: AIRCRAFT TYPE AND AIRWORTHINESS CERTIFICATION 14 CFR PART 36

II. NOISE STANDARDS: AIRCRAFT TYPE AND AIRWORTHINESS CERTIFICATION 14 CFR PART 36

(3) Supplemental Type Certificates: See paragraph 6-3(j) of reference 7 of this AC. (4) Definitions of Terms: Paragraph 4 of this Advisory Circular provides definitions for the following terms related to the aircraft types and categories within Items (1) – (4) of section 36.1(a).

Aircraft Large Aircraft Airplane Small Aircraft Helicopter Propeller Airplane Categories (See Note A) Jet Airplane - Acrobatic Turboprop Airplane (See Note C) - Commuter - Normal - Primary - Restricted (See Note B) - Transport - Utility Helicopter Categories - Normal - Transport Notes:

(A) Airplane Categories and Aircraft Classes: Part 1 recognizes a distinction between Airplane Categories (e.g., acrobatic, commuter, normal, primary, restricted, transport and utility) and Aircraft Classes (e.g., Conventional Takeoff and Landing (CTOL), Vertical Takeoff and Landing (VTOL), Short Takeoff and Landing (STOL), Reduced Takeoff and Landing (RTOL), and Supersonic Transports (SST)). The noise certification requirements contained in part 36 are specified for several Airplane and Helicopter Categories but not for STOL, RTOL, SST (except for Concorde), or VTOL Aircraft Classes.

(B) Restricted Category Propeller-Driven Large Airplanes: Propeller-driven large airplanes that have been type certificated in the restricted category (See part 21, section 21.25) are not required to demonstrate compliance with the requirements of part 36. In the absence of part 36 applicability, an Environmental Assessment is required (See FAA Order 8110.B (reference 7 of this AC) paragraph 6-3(d) for additional information).

(C) Turboprop Airplanes: Turboprop-powered airplanes are included under the part 36 requirements applicable to propeller-driven airplanes (i.e. subsonic transport category large airplanes; propellerdriven small airplanes, including acrobatic, normal, restricted, and transport categories; or propeller-driven commuter category airplanes).

c. Procedures

None 15. Section 36.1(b) Each person who applies under part 21 of this chapter for a type of airworthiness certificate specified in this part must show compliance with the applicable requirements of this part, in addition to the applicable airworthiness requirements of this chapter.

a. Explanation

This section specifies that an applicant must comply with appropriate airworthiness requirements and part 36 requirements as a part of the total aircraft certification process.

b. Supplemental Information

(1) Aircraft Configuration for Noise Certification: An applicant’s proposal for an aircraft configuration to be certified under the requirements of part 36 must include any type design changes that may be a result of airworthiness standards testing and analysis, and which would result in acoustical changes (See section 36.1(c), Supplemental Information item number (2) for FAA criteria on when aircraft type design changes represent an acoustical change). If an applicant does not propose the appropriate aircraft configuration, additional noise certification testing and analysis may be required.

c. Procedures

None 16. Section 36.1(c).

Each person who applies under 14CFR part 21 of this chapter for approval of an acoustical change described in § 21.93(b) of this chapter must show that the aircraft complies with the applicable provisions of Sections 36.7, 36.9, or 36.11 of this part in addition to the applicable airworthiness requirements of this chapter.

a. Explanation:

This section specifies part 36 requirements when “ voluntary” changes are made to the type design of an aircraft under the provisions of part 21.

b. Supplemental Information:

(1) Acoustical Change: Part 21, section 21.93(b) defines an aircraft “acoustical change” and specific aircraft configurations excepted from part 36 requirements. The text of part 21, section 21.93(b) is as follows (Also see paragraph 6-3(i) of reference 7 of this AC).

(b) For the purpose of complying with part 36 of this chapter, and except as provided in paragraphs (b)(2), (b)(3), and (b)(4) of this section, any voluntary change in the type design of an aircraft that may increase the noise levels of that aircraft is an “acoustical change” (in addition to being a minor or major change as classified in paragraph in paragraph (a) of this section) for the following aircraft:

(1) Transport category large airplanes. (2) Jet (Turbojet powered) airplanes (regardless of category). For airplanes to which this paragraph applies, “acoustical changes” do not include changes in type design that are limited to one of the following–

(I) Gear down flight with one or more retractable landing gear down during the entire flight, or (ii) Spare engine and nacelle carriage external to the skin of the airplane (and return of the pylon or other external mount), or

(iii) Time-limited engine and/or nacelle changes, where the change in type design specifies that the airplane may not be operated for a period of more than 90 days unless compliance with the applicable acoustical change provisions of part 36 of this chapter is shown for that change in type design.

(3) Propeller driven commuter category and small airplanes in the primary, normal, utility, acrobatic, transport, and restricted categories, except for airplanes that are:

(I) Designated for “agricultural aircraft operations” (as defined in 34 137.3 of this chapter, effective January 1, 1966) to which § 36.1583 of this chapter does not apply, or

(ii) Designated for dispensing fire fighting materials to which § 36.1583 of this chapter does not apply, or

(iii) US registered, and that had flight time prior to January 1, 1955 or

(iv) Land configured aircraft reconfigured with floats or skis. This reconfiguration does not permit further exception from the requirements of this section upon any acoustical change not enumerated in § 21.93(b).

(4) Helicopters, (except for those helicopters that are designated exclusively for “agricultural aircraft operations”, as defined in § 137.2 of this chapter, as effective on January 1, 1966, for dispensing fire fighting materials, or for carrying external loads, as defined in § 133.1(b) of this chapter, as effective on December 20, 1976). For helicopters to which this paragraph applies, “acoustical changes” include the following type design changes:

(i) Any changes to, or removal of, a muffler or other component designed for noise control. (ii) Any other design or configuration change (including a change in the operating limitations of the aircraft) that, based on FAA-approved analytical or test data, the Administrator determines may result in an increase in noise level.”

(2) Voluntary Changes in Type Design: A voluntary change in the configuration of an aircraft means a change in the type design of that aircraft. Examples of voluntary changes in aircraft type design that may affect part 36 certificated noise levels are as follows:

i. Increased engine thrust (power) to improve aircraft performance; ii. Maximum gross weight changes; iii. Limitations on operational flap settings related to noise; iv. Hardware revisions (e.g., vortex generators, flap configuration, wing tip stabilizers, wing tip fuel tanks, etc.);

v. Engine modifications to improve engine performance, acceleration, deceleration, or surge margin protection;

vi. Addition of wing or body hardware to improve aerodynamics; vii. External nacelle changes to improve air flow patterns; viii. Engine inlet changes to improve ice protection; ix. Reduction of engine blade tip clearances to improve inlet flow characteristics, and; x. Modifications to engine/nacelle acoustic treatments. (3) Acoustical Change Criteria: A voluntary change in the type design of an aircraft that may result in an increase in its certificated noise levels is defined as an “ acoustical change.” The numerical criteria used by the FAA in defining an acoustical change is a change in certificated flyover, lateral or approach noise levels of 0.10 EPNdB/dB (A) (if such changes are not formally tracked by an FAA approved method) or 0.30 EPNdB/dB (A) if an applicant has obtained an FAA approved plan to track and sum cumulative changes. These criteria are also provided in section 1.4.3 of the appended ICAO TM and are established to limit the cumulative effects of multiple small changes.

(4) No Acoustical Changes: Type design changes that do not result in an “ acoustical change” as defined in part 21, section 21.93(b) are referred to as “no acoustical changes” (NAC).

(5) NAC Cumulative Effects: When type design changes result in reduced noise levels, an applicant may elect not to provide the full part 36 substantiation, but instead provide FAA with data and/or information to substantiate a NAC. However subsequent type design changes may require full part 36 certification because of cumulative acoustical effects. Example: An applicant proposes a configuration change which will reduce the noise levels by approximately 2.1 dB for the flyover noise measurement point, 1.1 dB for the lateral noise measurement point, and with no change in noise level at the approach noise measurement point. FAA verifies that the noise levels were reduced, and the applicant accepts the pre-change configuration certificated noise levels as published in the AFM to apply to this change in type design. The applicant may not make another type design change as a NAC that increases the flyover noise level and the lateral noise level without providing substantiation of the cumulative effects of this type design change on AFM noise certificated levels. Multiple type design changes must be evaluated on a cumulative basis (as a combined single configuration) for each noise measurement point for the purposes of determining whether there is an acoustical change.

(6) Non-Standard Jet Airplane Configurations: Sections 21.93(b)(2)(i) and (ii) specify exceptions under which certain changes in jet airplane type design are not subject to compliance with 14 CFR part 36 requirements because such configurations are not intended for normal operations, but are typically required for maintenance operations (e.g., ferry flights, transporting engines to aircraft that cannot be ferried, etc.).

(7) Time-Limited Changes: Time-Limited engine or nacelle changes on jet airplanes for periods of up to 90 days (as specified in part 21, section 21.93(b)(2)(iii)) may be necessary for continued airplane operation until maintenance can be performed on the original engines or nacelles that were changed. These changes must comply with applicable airworthiness standards and the maintenance, preventative maintenance, rebuilding and alteration inspection requirements of part 43. Such changes do not require compliance with part 36 requirements even though they may result in an increase in airplane noise levels, relative to the certificated noise levels. FAA policy (See Federal Register Vol. 64, No. 225, Page 65655, dated November 23, 1999) permits the 90 day period allowed by part 21, section 21.93(b)(2)(iii) to continue to be used after December 31, 1999, but only for maintenance-related purposes. It cannot be used for meeting Stage 3 requirements due to lack of an adequate number of spare engines or nacelles, or insufficient number of engines or nacelles to operate a Stage 3 fleet at a given time. Section 21.93(b)(2)(iii) may only be used to intermix engines when maintenance is required and no conforming engine or nacelle for the configuration is available.

(8) Special Purpose Aircraft: Type design changes to propeller-driven small airplanes and helicopters do not need to comply with the provisions of part 36 when they are operated for special purposes as specified in part 21, sections 21.93(b)(3)(i-iv) and 21.93(b)(4).

c. Procedures

(1) Applicant’s Responsibility: Pursuant to section 21.93(b), an applicant must identify type design changes that affect an aircraft’s certificated noise levels by aircraft serial number and must demonstrate part 36 compliance for those aircraft. The noise levels approved by the FAA for the modified aircraft must be documented in an FAA Approved AFM or RFM by either a revision to the AFM or RFM (typically an option only available to the aircraft manufacturer), an AFM or RFM Supplement (for Supplemental Type Certificates and Field Approvals), or a Supplemental AFM or RFM (for aircraft that do not have a FAA Approved AFM or RFM). Configurations and modifications for which noise approval is required must be found to comply with applicable airworthiness requirements specified in part 21 as well as the requirements of part 36 [reference section 36.3].

(2) NAC Approvals: FAA may approve results of component laboratory demonstrations, backto-back noise comparisons from ground tests or flight tests of each configuration, acoustical analyses, etc as acceptable for substantiating that an applicant’s proposed changes to an aircraft type design is an NAC. The results from these evaluations must be applicable to an aircraft’s certified noise levels at the part 36 reference noise measurement points. 17. Section 36.1(d)

Each person who applies for the original issue of a standard airworthiness certificate for a subsonic transport category large airplane or for a jet airplane under14CFR part 21 § 21.183 must, regardless of date of application, show compliance with the following provisions of this part (including Appendix B):

(1) The provisions of this part in effect on December 1, 1969, for subsonic airplanes that have not had any flight time before--

(I) December 1, 1973, for airplanes with maximum weights greater than 75,000 pounds, except for airplanes that are powered by Pratt & Whitney Turbo Wasp JT3D series engines;

(ii) December 31, 1974, for airplanes with maximum weights greater than 75,000 pounds and that are powered by Pratt & Whitney Turbo Wasp JT3D series engines; and

(iii) December 31, 1974, for airplanes with maximum weights of 75,000 pounds and less. (2) The provisions of this part in effect on October 13, 1977, including the stage 2 noise limits, for Concorde airplanes that have not had flight time before January 1, 1980.

a. Explanation

None b. Supplemental Information

(1) Requirements for Issuance of Airworthiness Certificates: An airworthiness certificate is issued for each airplane produced, and is a means of distinguishing (by date of issuance) airplanes within a production run that comply with the noise certification requirements of part 36. Prior to the original issuance of a standard airworthiness certificate (see part 21, section 21.183) and regardless of the date of application for certification, compliance with the regulatory requirements of part 36 (including Appendix B) is required for a transport category large airplane, or for a jet airplane regardless of category (see paragraph 6-3(k)(1) of reference 7 of this AC). The following Table summarizes the requirements of section 36.1(d).

Maximum Airplane

Weights

Airplane

Types

Engine Configuration

Effective Date of

part36

Compliance Date for Airplanes With Initial Flight Time on or After 75,000 pounds or less

Subsonic All engines December 1, 1969 December 31, 1974

Greater than 75,000 Subsonic Without Pratt & Whitney JT3D engines

December 1, 1969 December 1, 1973

Greater than 75,000 Subsonic With Pratt & Whitney JT3D engines

December 1, 1969 December 31, 1974

Concorde – all weights

Supersonic All engines October 13, 1977 January 1, 1980

(2) “Grandfathered” Airplanes: Airplane types not identified above are “grandfathered” airplanes and are permitted to continue normal operations without showing compliance with the requirements of part 36. For example, the twin-engine propeller-driven Convair 580 or Douglas DC-3 airplanes that first logged flight time before December 31, 1974, did not have to comply with the noise provisions of part 36 and may have received a standard airworthiness certificate under the provisions of part 21, section 21.183, or may have received a standard airworthiness certificate under the provisions of the regulations in effect at the time of certification without compliance with part 36.

c. Procedures:

None. 18. Section 36.1(e)

Each person who applies for the original issue of a standard airworthiness certificate under part 21, § 21.183, or for the original issue of a restricted category airworthiness certificate under 1 part 21, § 21.185, for propeller-driven, commuter category airplanes for a propeller-driven small airplane that has not had any flight time before January 1, 1980, must show compliance with the applicable provisions of this part.

a. Explanation

None

b. Supplemental Information

(1) Requirements for Issuance of Airworthiness Certificates: An applicant must show compliance of individual airplanes with the requirements of part 36 prior to issuance of airworthiness certificates, as prescribed in part 21, section 21.183 or 21.185 (see paragraph 6-3(k)(2) of reference 7 of this AC).

(2) Commuter Category Airplanes: Since airworthiness standards for commuter category airplanes became effective February 17, 1987, (under part 21, Amendment 21-59) there are no airplanes in this category with initial flight time before January 1, 1980. All commuter category airplanes are thus required to show compliance with the noise certification requirements of part 36.

c. Procedures

None. 19. Section 36.1(f)

For the purpose of showing compliance with this part for transport category large airplanes and jet-airplanes regardless of category, the following terms have the following meanings:

(1) A "Stage 1 noise level" means a flyover, lateral or approach noise level greater than the Stage 2 noise limits prescribed in section B36.5(b) of Appendix B of this part.

(2) A "Stage 1 airplane" means an airplane that has not been shown under this part to comply with the flyover, lateral, and approach noise levels required for Stage 2 or Stage 3 airplanes.

(3) A "Stage 2 noise level" means a noise level at or below the Stage 2 noise limits prescribed in section B36.5(b) of Appendix B of this part but higher than the Stage 3 noise limits prescribed in section B36.5(c) of Appendix B of this part.

(4) A "Stage 2 airplane" means an airplane that has been shown under this part to comply with Stage 2 noise levels prescribed in section B36.5(b) of Appendix B of this part (including use of the applicable tradeoff provisions specified in section B36.6) and that does not comply with the requirements for a Stage 3 airplane.

(5) A "Stage 3 noise level" means a noise level at or below the Stage 3 noise limits prescribed in section B36.5(c) of Appendix B of this part.

(6) A "Stage 3 airplane" means an airplane that has been shown under this part to comply with Stage 3 noise levels prescribed in section B36.5(c) of Appendix B of this part (including use of the applicable tradeoff provisions specified in section B36.6).

(7) A "subsonic airplane" means an airplane for which the maximum operating limit speed, Mom does not exceed a Mach number of 1.

(8) A "supersonic airplane" means an airplane for which the maximum operating limit speed, Mmo exceeds a Mach number of 1.

20. Section 36.1(g)

For the purpose of showing compliance with this part for transport category large airplanes and jet airplanes regardless of category, each airplane may not be identified as complying with more than one stage or configuration simultaneously.

a. Explanation

This section specifies that each airplane configuration may be certificated to noise levels within the noise limits established for one stage only.

b. Supplemental Information

(1) In-flight Configuration Changes: In-flight changes in an airplane configuration (including changes in maximum gross weight) that could result in multiple certificated noise levels for a given noise measurement point or stage classification are not permitted. They are changes in the airplane type design and therefore require a change in operating limitations. A change in maximum gross weight requires an applicant to remove an airplane from service, and comply with the approval procedures of part 43.5 and 43.7. The type design approval procedures under part 21 must be followed if the change does not have prior certification approval.

c. Procedures

None 21. Section 36.1(h)

For the purpose of showing compliance with this part, for helicopters in the primary, normal, transport, and restricted categories, the following terms have the specified meanings:

(1) Stage 1 noise level means a takeoff, flyover, or approach noise level greater than the Stage 2 noise limits prescribed in section H36.305 of Appendix H of this part, or a flyover noise level greater than the Stage 2 noise limits prescribed in section J36.305 of appendix J of this part.

(2) Stage 1 helicopter means a helicopter that has not been shown under this part to comply with the takeoff, flyover, and approach noise levels required for Stage 2 helicopters as prescribed in section H36.305 of Appendix H of this part, or a helicopter that has not been shown under this part to comply with the flyover noise level required for Stage 2 helicopters as prescribed in section J36.305 of Appendix J of this part.

(3) Stage 2 noise level means a takeoff, flyover, or approach noise level at or below the Stage 2 noise limits prescribed in section H36.305 of Appendix H of this part, or a flyover noise level at or below the Stage 2 limit prescribed in section J36.305 of Appendix J of this part.

(4) Stage 2 helicopter means a helicopter that has been shown under this part to comply with Stage 2 noise limits (including applicable tradeoffs) prescribed in section H36.305 of Appendix H of this part, or a helicopter that has been shown under this part to comply with the Stage 2 noise limit prescribed in section J36.305 of Appendix J of this part.

a. Explanation

None

b. Supplemental Information

(1) The Stage 1 noise limits apply to all helicopters for which application for a type certificate or a change in type design was made prior to March 6, 1986.

(2) The Stage 2 noise levels apply to all helicopters for which application for a type certificate or a change in type design is made on or after March 6, 1986, with the following exception. For helicopters for which application for issuance of an original type certificate in the normal, transport or restricted category is made on or after March 6, 1986, and which the FAA finds to be the first civil version of a helicopter which was designed and constructed for, and accepted for operational use by an Armed Force of the U.S. or the U.S. Coast Guard on or before March 6, 1986, it must be shown that the noise levels of the helicopter certificated under the provisions of Appendix H are no greater than Stage 2 levels plus 2 EPNdB at each measuring point. There is no

corresponding provision under Appendix J. The tradeoff provision of H36.305(b) may not be used to show compliance with Stage 2 levels plus 2 EPNdB, nor may they be used to increase any noise level beyond these limits. Subsequent civil versions (acoustic changes) must meet the Stage 2 requirements without the extra 2 EPNdB at each measuring point. The tradeoff provisions of H36.305(b) may be used in showing stage 2 compliance for these subsequent versions.

(3) Helicopters Excepted: Helicopters that are designated exclusively for agricultural aircraft operations, as defined in part 137, section 137.3, for dispensing fire fighting materials, or for carrying external loads, as defined in part 133, section 133.1(b) are excluded from the noise certification requirements.

(4) Stage 1/Stage 2: A helicopter, with a maximum take-off weight of 6000lbs (2,721kg) or less, that marginally fails to comply with the Stage 2 noise limit (by ~0.5 dB margin) prescribed in appendix J (section J36.305) has the alternative to comply with the Stage 2 noise limit of Appendix H (section H36.305). Note: The Appendix J noise limit uses a sound exposure level (SEL) that was defined more stringent by approximately 2 dB than the corresponding average of the three Appendix H noise limits in EPNL. However, this is no guarantee that subsequent Appendix H noise certification testing will comply, especially for a military helicopter seeking civil certification.

c. Procedures

None 22. Section 36.2 Requirements as of date of application.

(a) Section 21.17 of this chapter notwithstanding, each person who applies for a type certificate for an aircraft covered by this part, must show that the aircraft meets the applicable requirements of this part that are effective on the date of application for that type certificate. When the time interval between the date of application for the type certificate and the issuance of the type certificate exceeds 5 years, the applicant must show that the aircraft meets the applicable requirements of this part that were effective on a date, to be selected by the applicant, not earlier than 5 years before the issue of the type certificate. (b) Section 21.101(a) of this chapter notwithstanding, each person who applies for an acoustical change to a type design specified in § 21.93(b) of this chapter must show compliance with the applicable requirements of this part that are effective on the date of application for the change in type design. When the time interval between the date of application for the change in type design and the issuance of the amended or supplemental type certificate exceeds 5 years, the applicant must show that the aircraft meets the applicable requirements of this part that were effective on a date, to be selected by the applicant, not earlier than 5 years before the issue of the amended or supplemental type certificate.

(c) If an applicant elects to comply with a standard in this part that was effective after the filing of the application for a type certificate or change to a type design, the election:

(1) must be approved by the FAA; (2) must include standards adopted between the date of application and the date of the election;

(3) may include other standards adopted after the standard elected by the applicant as determined by the FAA.

a. Explanation

Section 36.2 specifies the applicable part 36 requirements to be those in effect on the date of application for the a) aircraft type certificate or b) change in type design. If the time interval between application for the type certificate (or change in type design) and the issuance of the type certificate (or amended or supplemental type certificate) exceeds 5 years, the applicable part 36 requirements are those in effect, on a date to be selected by the applicant, not earlier than 5 years before the date of issuance of the type certificate, amended type certificate, or supplemental type certificate.

Section 36.2(c) permits the applicant to elect to demonstrate compliance with a later part 36 standard than is required by section 36.2(a) or (b). For the purposes of Section 36.2, “standard” refers to any of the requirements contained in part 36. As specified in sections 36.2(c)(1) and (2), an applicant’s election of a later standard is subject to FAA approval, and the election must include standards adopted between the date of application and the effective date of the standard that the applicant has elected to comply with. Thus, an applicant’s election to demonstrate compliance with a particular later standard would also require that compliance be demonstrated with all other part 36 standards (applicable to the aircraft type) adopted between the date of application and the effective date of the standard that the applicant has elected to comply with. Further, in accordance with section 36.2(c)(3), the FAA may require compliance with other standards that were adopted after the date of the elected standard. For the purposes of section 36.2(c)(3), “other standards” refers to other 14 CFR part 36 standards. For example, if the compliance standard elected under section 36.2(c)(3) had later been revised, the FAA may determine that it is appropriate for compliance to be demonstrated with the revised standard. Such a determination would also require that compliance be demonstrated with all other part 36 standards (applicable to the aircraft type) adopted between the date of application and the effective date of the standard that the FAA has determined to be the appropriate compliance basis.

b. Supplemental Information

None

c. Procedures

None 23. Section 36.3 Compatibility with airworthiness requirements

It must be shown that the aircraft meets the airworthiness regulations constituting the type certification basis of the aircraft under all conditions in which compliance with this part is shown, and that all procedures used in complying with this part, and all procedures and information for the flight crew developed under this part, are consistent with the airworthiness regulations constituting the type certification basis of the aircraft.

a. Explanation

None

b. Supplemental Information

None

c. Procedures

(1) Aircraft certification tests and analyses must be conducted using configurations, procedures and information which are consistent with the airworthiness regulations applicable to that aircraft. For example, noise tests or analyses may not be conducted with landing flap settings which could not meet the applicable airworthiness regulation requirements.

24. Section 36.5 Limitation of part

Pursuant to 49 U.S.C. 1431(b)(4), the noise levels in this part have been determined to be as low as is economically reasonable, technologically practicable, and appropriate to the type of aircraft to which they apply. No determination is made, under this part, that these noise levels are or should be acceptable or unacceptable for operation at, into, or out of, any airport.

a. Explanation

This section specifies legal limitations regarding part 36. b. Supplemental Information

(1) Scope of part 36 Regulation: Part 36 requires compliance with U.S. Government noise standards for aircraft type and airworthiness certification but does not include noise standards related to aircraft operations, such as is provided in part 91. Part 36 certificated noise levels are achieved using procedures which can be duplicated practicably in normal operations by flight crews with safe reserves of thrust (power) and speed. Public Law 103-272 (reference 2 of this AC), mandates that the Administrator of the FAA prescribe standards to measure and evaluate aircraft noise. Under this law, an original type certificate may be issued for an aircraft for which substantial noise abatement can be achieved only after the FAA Administrator prescribes standards and regulations that apply to that aircraft. Consideration must be given to relevant information on aircraft noise, consultations with appropriate US and State authorities, whether the standards or regulations are consistent with the highest degree of safety and are economically reasonable, technologically practical, and appropriate for the type of aircraft to which they apply.

c. Procedures

None 25. Section 36.6 Incorporations by reference 26. Section 36.6(a)

General. This part prescribes certain standards and procedures that are not set forth in full text in the rule. Those standards and procedures are contained in published material which is reasonably available to the class of persons affected and has been approved for incorporation by reference by the Director of the Federal Register under 5 U.S.C. 552 (a) and 1 CFR Part 51. 27. Section 36.6(b)

Incorporated matter. (1) Each publication, or part of a publication, which is referenced but not set forth in full-text in this part and which is identified in paragraph (c) of this section is hereby incorporated by reference and made a part of part 36 of this chapter with the approval of the Director of the Federal Register. (2) Incorporated matter which is subject to subsequent change is incorporated by reference according to the specific reference and to the identification statement. Adoption of any subsequent change in incorporated matter is made under part 11 of this chapter and 1 CFR part 51.

a. Explanation

This section specifies requirements for publications or documents to be “incorporated by reference” into part 36 and the process necessary when incorporated matter is subject to subsequent change.

b. Supplemental Information

None

c. Procedures

None

28. Section 36.6(c)

Identification statement. The complete title or description, which identifies each published matter incorporated by reference in this part, is as follows:

(1) International Electrotechnical Commission (IEC) Publications. (i) IEC Publication No. 179, entitled "Precision Sound Level Meters," dated 1973. (ii) IEC Publication No. 225, entitled "Octave, Half-Octave, Third Octave Band Filters Intended for the Analysis of Sounds and Vibrations," dated 1966.

(iii) IEC Publication No. 651, entitled "Sound Level Meters," first edition, dated 1979. (iv) IEC Publication No. 561, entitled "Electro-acoustical Measuring Equipment for Aircraft Noise Certification," first edition, dated 1976.

(v) IEC Publication No. 804, entitled "Integrating-averaging Sound Level Meters," first edition, dated 1985.

(vi) IEC Publication 61094-3, entitled “measurement microphones- Part 3: Primary Method for Free-Field Calibration of Laboratory Standard Microphones by the Reciprocity Technique”, first edition, dated 1995

(vii) IEC Publication 61094-4, entitled “Measurement Microphones- Part 4: Specifications for Working Standard Microphones”, first edition, dated 1995

(viii) IEC Publication 61260, entitled “Electroacoustics-Octave-Band and Fractional-Octave-Band filters”, first edition, dated 1995

(ix) IEC Publication 61265: entitled “Instruments for Measurement of Aircraft Noise- Performance Requirements for Systems to Measure One-Third-Octave-Band Sound Pressure Levels in Noise Certification of Transport-Category Aeroplanes”, first edition, dated 1995

(x) IEC Publication 60942, entitled “Electroacoustics- Sound Calibrators”, second edition, dated 1997 (2) Society of Automotive Engineers (SAE) Publications. (i) SAE ARP 866A, entitled "Standard Values at Atmospheric Absorption as a Function of Temperature and Humidity for Use in Evaluating Aircraft Flyover Noise," dated March 1975.

a. Explanation

This section identifies standards and procedures that are incorporated by reference into part 36 as requirements for noise measurement and evaluation of various aircraft types.

b. Supplemental Information

(1) Other Publications. Other publications (see reference list of the appended ICAO TM) may be useful to an applicant during implementation of an aircraft noise certification process. Applicant proposals for use of standards and procedures found in these publications must be included in an applicant’s noise compliance demonstration plan and approved by FAA. An applicant should also contact an ACO Specialist prior to submittal of a noise compliance demonstration plan to FAA to determine whether there are new standards and procedures that are applicable to his particular aircraft noise certification process.

c. Procedures

None 29. Section 36.6(d)

Availability for purchase. Published material incorporated by reference in this part may be purchased at the price established by the publisher or distributor at the following mailing addresses:

(1) IEC publications, (i) International Electrotechnical Commission,3, rue de Varembe, Case postale 131, 1211 Geneva 20, Switzerland

(ii) American National Standard Institute, 11 West 42nd Street, New York City, New York 10036 (Electronic mail address: [email protected]).

(2) SAE publications. Society of Automotive Engineers, Inc., 400 Commonwealth Drive, Warrentown, Pennsylvania 15096.(Electronic mail address: [email protected])

a. Explanation

None

b. Supplemental Information

(1) Addresses of Other Organizations: Addresses for other organizations that produce technical standards, references and publications that relate to aircraft noise certification are as follows:

(i) Bureau International de Métrologie Légale 11, rue Turgot 75009 Paris, France (ii) Engineering Science Data Unit International, Ltd. 251-259 Regent Street London, England W1R 7AD, United Kingdom (iii) International Civil Aviation Organization 999 University Street Montreal, Quebec Canada H3C 5H7 (Electronic mail address: [email protected]) (iv) National Institute of Standards and Technology Building 101, Room A903 Gaithersburg, Maryland 20899 (Electronic mail address: [email protected])

c. Procedures

None 30. Section 36.6(e)

Availability for inspection. A copy of each publication incorporated by reference in this part is available for public inspection at the following locations:

(1) FAA Office of the Chief Counsel, Rules Docket, Room 916, Federal Aviation

Administration Headquarters Building, 800 Independence Avenue, SW., Washington, D.C. (2) Department of Transportation, Branch Library, Room 930, Federal Aviation

Administration Headquarters Building, 800 Independence Avenue, SW., Washington, D.C. (3) The respective Region Headquarters of the Federal Aviation Administration as

follows: (i) New England Region Headquarters, 12 New England Executive Park, Burlington, Massachusetts 01803. (ii) Eastern Region Headquarters, Federal Building, John F. Kennedy (JFK) International Airport, Jamaica, New York 11430. (iii) Southern Region Headquarters, 1701 Columbia Avenue, College Park, Georgia, 30337.

(iv) Great Lakes Region Headquarters, O'Hare Lake Office Center, 2300 East Devon Avenue, Des Plaines, Illinois 60018. (v) Central Region Headquarters, Federal Building, 601 East 12th Street, Kansas City Missouri 64106. (vi) Southwest Region Headquarters,2601 Meacham Boulevard, Fort Worth, Texas 76137-4298. (vii) Northwest Mountain Region Headquarters 1601 Lind Avenue, Southwest, Renton, Washington 98055. (viii) Western-Pacific Region Headquarters 15000 Aviation Boulevard, Hawthorne, California 92007. (ix) Alaskan Region Headquarters, 222 West 7th Avenue, # 14, Anchorage, Alaska 99513. (x) European Office Headquarters, 15, Rue de la Loi (3rd Floor), B-1040 Brussels, Belgium.

a. Explanation

None b. Supplemental Information

(1) Other DOT/FAA Addresses: Current addresses of U.S. Department of Transportation and FAA organizations (and Specialists) that might provide assistance to an applicant are as follows:

(2) FAA/DOT Offices, Washington, D.C.:

(i) FAA Office of Environment and Energy (AEE-1) Federal Aviation Administration Headquarters Building, Room 900W, 800 Independence Avenue, SW. Washington D.C. 20591 (ii) FAA Office of the Chief Council (AGC-1) Federal Aviation Administration Headquarters Building, Room 900E 800 Independence Avenue, SW. Washington D.C. 20591 (iii) U.S. Department of Transportation Branch Library Federal Aviation Administration Headquarters Building, Room 930 800 Independence Avenue, SW. Washington D.C. 20591 (3) FAA Noise Certification Specialists: (i) Rotorcraft Noise Certification Specialist (ASW-110) Federal Aviation Administration Rotorcraft Directorate 2601 Meacham Boulevard Fort Worth, Texas, 76137-4298 (mailing address: DOT FAA Fort Worth, Texas 76193-0110) (ii) Small Airplane Noise Certification Specialist (ACE-111) Federal Aviation Administration Small Airplane Directorate 901 Locust, Room 301

Kansas City, Missouri, 64106 (iii) Transport Airplane Noise Certification Specialist (ANM-112) Federal Aviation Administration Los Angeles Aircraft Certification Office 3960 Paramount Blvd., Suite 100 Lakewood, California 90712-4137 Note: These Specialists are located in their respective Directorates. (4) FAA Directorates: (i) Engine and Propeller Directorate (ANE-100) Federal Aviation Administration 12 New England Executive Park Burlington, Massachusetts 01803-5299 (ii) Rotorcraft Directorate (ASW-100) Federal Aviation Administration 2601 Meacham Boulevard Fort Worth, Texas 76193 (iii) Small Airplane Directorate (ACE-100) Federal Aviation Administration 1201 Walnut Street Kansas City, Missouri 64106 (iv) Transport Airplane Directorate (ANM-100) Federal Aviation Administration 1601 Lind Avenue Southwest Renton, Washington 98055 -4056 Note: These Directorates are involved in aircraft certification and continued airworthiness

activities. (5) FAA Regional Headquarters: (i) Alaskan Region Headquarters (AAL-1) Federal Aviation Administration 222 West 7th Avenue, # 14 Anchorage, Alaska 99513-7587 (ii) Central Region Headquarters (ACE-1) Federal Aviation Administration 601 East 12th Street Federal Building Kansas City, Missouri 64106 (iii) Eastern Region Headquarters (AEA-1) Federal Aviation Administration JFK International Airport Fitzgerald Federal Building Jamaica, New York 11430 (iv) Great Lakes Region Headquarters (AGL-1)

Federal Aviation Administration O’Hare Lake Office Center 2300 East Devon Avenue Des Plaines, Illinois 60018_4686 (v) New England Region Headquarters (ANE-1) Federal Aviation Administration 12 New England Executive Park Burlington, Massachusetts 01803-5299 (vi) Northwest Mountain Region Headquarters (ANM-1) Federal Aviation Administration 1601 Lind Avenue Southwest Renton, Washington 98055-4056 (vii) Southern Region Headquarters (ASO-1) Federal Aviation Administration 1701 Columbia Avenue College Park, Georgia 30337 (viii) Southwest Region Headquarters (ASW-1) Federal Aviation Administration 2601 Meacham Boulevard Fort Worth, Texas 76137- 4298 (mailing address: DOT/FAA Fort Worth, Texas 76193-0001) (ix) Western-Pacific Region Headquarters (AWP-1) Federal Aviation Administration 15000 Aviation Blvd. Hawthorne, CA 90261 (mailing address: Western-Pacific Region Headquarters (AWP-1) Federal Aviation Administration PO Box 92007 Worldway Postal Center Los Angeles, Ca, 90009) (6) FAA Aircraft Certification Offices (ACO): (i) Anchorage Aircraft Certification Office (ACE-115N) Federal Aviation Administration 222 West 8th Avenue Anchorage, Alaska 99513-7587 (ii) Atlanta Aircraft Certification Office (ACE-115A) Federal Aviation Administration One Crown Center 1895 Phoenix Boulevard, Suite 450 Atlanta, Georgia 30349 (iii) Boston Aircraft Certification Office (ANE-150)

Federal Aviation Administration 12 New England Executive Park Burlington, Massachusetts 01803-5299 (iv) Brussels Aircraft Certification Staff (AEU-100) Federal Aviation Administration c/o American Embassy 15 rue de la Loi (1st Floor) B-1040 Brussels, Belgium (mailing address: Federal Aviation Administration (AEU-100) c/o American Embassy PSC 82, Box 002 APO AE 09724) (v) Chicago Aircraft Certification Office (ACE-115C) Federal Aviation Administration 2350 East Devon, Room 332 Des Plaines, Illinois 60018 (mailing address: Chicago Aircraft Certification Office (ACE-115C) Federal Aviation Administration 2300 East Devon Chicago, Illinois 60018) (vi) Denver Aircraft Certification Office (ANM-100D) Federal Aviation Administration Technical Operations Center 26805 East 68th Avenue, Room 214 Denver, Colorado 80249 (vii) Engine Certification Office (ANE-140) Federal Aviation Administration 12 New England Executive Park Burlington, Massachusetts 01803-5299 (viii) Fort Worth Aircraft Certification Office (ASW-150) Federal Aviation Administration 2601 Meacham Boulevard Fort Worth, Texas 76137-4298 (mailing address: DOT FAA Fort Worth, Texas 76193-0150) (ix) Fort Worth Rotorcraft Certification Office (ASW-170) Federal Aviation Administration 2601 Meacham Boulevard Fort Worth, Texas 76137-4298 (mailing address: DOT FAA

Fort Worth, Texas 76193-0170 (x) Fort Worth Special Certification Office (ASW-190) Federal Aviation Administration 2601 Meacham Boulevard Fort Worth, Texas 76137-4298 (mailing address: DOT FAA Fort Worth, Texas 76193-0190 (xi) Los Angeles Aircraft Certification Office (ANM-100L) Federal Aviation Administration 3960 Paramount Boulevard, Suite 100 Lakewood, California 90712-4137 (xii) New York Aircraft Certification Office (ANE-170) Federal Aviation Administration 10 Fifth Street, 3rd Floor Valley Stream, New York 11581-1200 (xiii) Seattle Aircraft Certification Office (ANM-100S) Federal Aviation Administration 1601 Lind Avenue Southwest Renton, Washington 98055-4056 (xiv) Wichita Aircraft Certification Office (ACE-115W) Federal Aviation Administration Mid-Continent Airport FAA Building, Room 100 1801 Airport Road Wichita, Kansas 67209 Note: An applicant must coordinate airworthiness and noise certification activities with the appropriate ACO Office. Assistance in selecting the appropriate ACO Office may be obtained from FAA Directorate, Regional or Noise Certification Specialist Offices.

c. Procedures

None 31. Section 36.7 Acoustical Change: Transport category large airplanes and jet airplanes 32. Section 36.7(a) Applicability. This section applies to all transport category large airplanes and jet airplanes for which an acoustical change approval is applied for under § 21.93(b) of this chapter. 33. Section 36.7(b)

General requirements. Except as otherwise specifically provided, for each airplane covered by this section, the acoustical change approval requirements are as follows:

(1) In showing compliance, noise levels must be measured and evaluated in

accordance with the applicable procedures and conditions prescribed in Appendix A of this part. (2) Compliance with the noise limits prescribed in section B36.5 of Appendix B must be

shown in accordance with the applicable provisions of section B36.7 and B36.8 of Appendix B of this part.

a. Explanation

This section specifies requirements for approval of acoustical changes applied for under part 21, section 21.93(b).

b. Supplemental Information

None c. Procedures

None 34. Section 36.7(c)

Stage 1 airplanes. For each Stage 1 airplane prior to the change in type design, in addition to the provisions of paragraph (b) of this section, the following apply:

(1) If an airplane is a Stage 1 airplane prior to the change in type design, it may not, after the change in type design, exceed the noise levels created prior to the change in type design. The tradeoff provisions of section B36.6 of Appendix B of this part may not be used to increase the Stage 1 noise levels, unless the aircraft qualifies as a Stage 2 airplane.

(2) In addition, for an airplane for which application is made after September 17, 1971-- (i) There may be no reduction in power or thrust below the highest airworthiness approved power or thrust, during the tests conducted before and after the change in type design; and

(ii) During the flyover and lateral noise tests conducted before the change in type design, the quietest airworthiness approved configuration available for the highest approved takeoff weight must be used.

a. Explanation

None

b. Supplemental Information

(1) Quietest Airworthiness Approved Configuration: This requirement was established to show that an acoustical change resulting from an approved type design change must be determined consistently. The FAA policy does not require an applicant to determine the quietest airworthiness approved configuration at the flyover or lateral noise measurement points by noise measurement and evaluation. However, FAA requires consistent evaluations between derivative and originally certificated configurations. For example, an applicant might choose an approved takeoff flap setting of 5 degrees. Later a type design change may be requested that would increase the flyover and lateral noise levels (an acoustical change). The FAA may not require the applicant to measure and evaluate all airworthiness approved takeoff flap settings (e.g., 0, 1, 2, 5, 10 degrees) to determine the quietest configuration, but may, in this example, require appropriate evaluations for a flap setting of 5 degrees.

c. Procedures

None

35. Section 36.7(d)

Stage 2 airplanes. If an airplane is a Stage 2 airplane prior to the change in type design, the following apply, in addition to the provisions of paragraph (b) of this section:

(1) Airplanes with high bypass ratio jet engines. For an airplane that has jet engines with a bypass ratio of 2 or more before a change in type design--

(i) The airplane, after the change in type design, may not exceed either (A) each Stage 3 noise limit by more than 3 EPNdB, or (B) each Stage 2 noise limit, whichever is lower:

(ii) The tradeoff provisions of section B36.6 of Appendix B of this part may be used in determining compliance under this paragraph with respect to the Stage 2 noise limit or to the Stage 3 plus 3 EPNdB noise limits, as applicable; and (iii) During the flyover and lateral noise test conducted before the change in type design, the quietest airworthiness approved configuration available for the highest approved takeoff weight must be used.

(2) Airplanes that do not have high bypass ratio jet engines. For an airplane that does not have jet engines with a bypass ratio of 2 or more before a change in type design-

(i) The airplane may not be a Stage 1 airplane after the change in type design; and (ii) During the flyover and lateral noise tests conducted before the change in type design, the quietest airworthiness approved configuration available for the highest approved takeoff weight must be used. .

a. Explanation

None b. Supplemental Information

See section 36.7(c), Supplemental Information, Item (1)

c. Procedures

None 36. Section 36.7(e)

Stage 3 airplanes. If an airplane is a Stage 3 airplane prior to the change in type design, the following apply, in addition to the provisions of paragraph (b) of this section:

(1) If compliance with Stage 3 noise levels is not required before the change in type design, the airplane must--

(I) Be a Stage 2 airplane after the change in type design and compliance must be shown under the provisions of paragraph (d)(1) or (d)(2) of this section, as appropriate; or

(ii) Remain a Stage 3 airplane after the change in type design. Compliance must be shown under the provisions of paragraph (e)(2) of this section.

(2) If compliance with Stage 3 noise levels is required before the change in type design, the airplane must be a Stage 3 airplane after the change in type design.

(3) Applications on or after [August 14, 1989.] The airplane must remain a Stage 3 airplane after the change in type design.

a. Explanation

None

b. Supplemental Information

(1) “Dual-Stage” Certificated Airplanes: Some older airplane models have been certificated to Stage 2 for one configuration and to Stage 3 for another configuration (e.g., airplane takeoff flap setting or maximum allowable gross weights). These airplanes are classified as “Dual-Stage” certificated airplanes. No new dual certifications will be considered.

c. Procedures

None 37. Section 36.9 Acoustical change: Propeller-driven small airplanes and propeller-driven commuter category airplanes [To be completed later] 38. Section 36.9(a) [To be completed later] 39. Section 36.9(b) [To be completed later] 40. Section 36.11 Acoustical Change: Helicopters

This section applies to all helicopters in the primary, normal, transport, and restricted categories for which an acoustical change approval is applied for under § 21.93(b) of this chapter on or after March 6, 1986. Compliance with the requirements of this section must be demonstrated under appendix H of this part, or, for helicopters having a maximum certificated takeoff weight of not more than 6,000 pounds, compliance with this section may be demonstrated under Appendix J of this part.

a. Explanation

None b. Supplementary Information

(1) Modifications excluded from compliance with part 36, as listed in part 21, section 21.93(b)(4)(ii) Classification of Changes in Type Design:

(i) Addition or removal of external equipment; (This means any instrument, mechanism, part, apparatus, appurtenance, or accessory that is attached to or extends from the helicopter exterior but is not used nor is intended to be used in operating or controlling a helicopter in flight and is not part of an airframe or engine).

(ii) Changes in the airframe made to accommodate the addition or removal to facilitate the use of external equipment, to provide for an external load attaching means, to facilitate the safe operation of the helicopter with external equipment mounted to, or external loads carried by, the helicopter;

(iii) Reconfiguration of the helicopter by the addition or removal of floats and skis; (iv) Flight with one or more doors and/or windows removed or in an open position; or (v) Any changes in the operational limitations on the helicopter as a consequence of the addition or removal of external equipment, floats, and skis, or flight operations with doors and/or windows removed or in an open position.

c. Procedures

None 41. Section 36.11(a)

General requirements. Except as otherwise provided, for helicopters covered by this section, the acoustical change approval requirements are as follows:

(1) In showing compliance with the requirements of appendix H of this part, noise levels must be measured, evaluated, and calculated in accordance with the applicable procedures and conditions prescribed in parts B and C of appendix H of this part. For helicopters having a maximum certificated takeoff weight of not more than 6,000 pounds that alternatively demonstrate compliance under appendix J of this part, the flyover noise level prescribed in appendix J of this part must be measured, evaluated, and calculated in accordance with the applicable procedures and conditions prescribed in part s B and C of appendix J of this part.

(2) Compliance with the noise limits prescribed in section H36.305 of appendix H of this part must be shown in accordance with the applicable provisions of part D of appendix H of this part. For those helicopters that demonstrate compliance with the requirements of appendix J of this part, compliance with the noise levels prescribed in section J36.305 of appendix J of this part must be shown in accordance with the applicable provisions of part D of appendix J of this part.

a. Explanation

None

b. Supplementary Information

(1) Equivalent Procedures: Subject to prior approval by the FAA, equivalent procedures may be used to measure, evaluate and calculate noise levels. Some commonly used equivalent procedures relating to helicopter noise certification will be included in a future revision to this AC.

(2) Noise Level Tradeoffs: Tradeoffs between the adjusted noise levels for flyover, takeoff and approach defined in H36.305(b) may be used to show compliance with the maximum noise levels (noise limits) of Appendix H. Since Appendix J only includes a flyover procedure, no tradeoff is possible.

c. Procedures

(1) Compliance: The procedure used to show compliance under Appendix H or Appendix J must follow the applicable parts of the regulation. Compliance with the maximum noise levels (noise limits) prescribed in section H36.305 of Appendix H or J36.305 of Appendix J must be shown. 42. Section 36.11(b)

Stage 1 helicopters. Except as provided in § 36.805(c), for each Stage 1 helicopter prior to a change in type design, the helicopter noise levels may not, after a change in type design, exceed the noise levels specified in section H36.305(a)(1) of appendix H of this part where the demonstration of compliance is under appendix H of this part. The tradeoff provisions under section H36.305(b) of appendix H of this part may not be used to increase any Stage 1 noise level beyond these limits. If an applicant chooses to demonstrate compliance under appendix J of this part, for each Stage 1 helicopter prior to a change in type design, the helicopter noise levels may not, after a change in type design, exceed the Stage 2 noise levels specified in section J36.305(a) of Appendix J of this part.

a. Explanation

None

b. Supplementary Information

(1) The maximum noise levels (noise limits) associated with a Stage 1 helicopter certificated under Appendix H after a change in type design are dependent on the noise levels of the original Stage 1 helicopter. Unless the Stage 1 helicopter after the change meets the Stage 2 maximum noise levels (noise limits), or Stage 2+ 2 EPNdB levels at each measuring point, it will be necessary to show that the helicopter has no increase in the noise levels at any of the measuring points. This will require determination of the noise levels associated with the original Stage 1 helicopter using Appendix H procedures. If this is not possible an applicant must obtain FAA approval for another procedure.

c. Procedures

None 43. Section 36.11(c)

Stage 2 helicopters. For each helicopter that is Stage 2 prior to a change in type design, the helicopter must be a Stage 2 helicopter after a change in type design

a. Explanation

None b. Supplementary Information

(1) Helicopter under 6000 lbs (2727 kg): If after a change in type design a helicopter previously certificated under Appendix J, fails to meet the Appendix J Stage 2 maximum noise levels (noise limits) prescribed in J36.305 an applicant may attempt to show compliance by electing the use of Appendix H procedures and the Appendix H Stage 2 maximum noise levels (noise limits) specified in H36.305.

(2) Noise Levels: Section 36.11 requirements apply to helicopters certificated under both Appendix H and Appendix J.

c. Procedures

None 44. – 50. RESERVED

a. Explanation

Subpart B specifies part 36 requirements for measurement and evaluation of airplane noise certification data, and maximum noise levels for Stage 1, Stage 2 and Stage 3 airplanes.

b. Procedures

None c. Procedures

None 51. Section 36.101 Noise measurement and evaluation

For transport category large airplanes and jet airplanes the noise generated by the airplane must be measured and evaluated under Appendix A of this part or under an approved equivalent procedure

a. Explanation

None

b. Supplemental Information

(1) Appendix A: Appendix A prescribes methodologies for conducting noise certification tests and for measurement and evaluation of noise data for comparison with maximum noise levels specified in Appendix B (see Note A). Specific requirements include:

(i) Specifications of various physical and environmental conditions under which airplane noise certification measurements are permitted. These conditions are related to the noise test site, wind velocity/direction and atmospheric sound attenuation.

(ii) Procedures for measurement of atmospheric parameters. (iii) Methods for synchronization of airplane position and performance measurements with noise measurements.

(iv) Specifications for noise certification measurement and analysis systems (See Note B). (v) Methods to calculate atmospheric sound attenuation coefficients and Effective Perceived Noise Level (in units of EPNdB).

(vi) Methods for adjustment of measured flight test data to reference conditions. (vii) Nomenclature for symbols and units. (viii) Specification of data to be reported to FAA.

Notes:

III. SUBPART B— TRANSPORT CATEGORY LARGE AIRPLANES AND JET AIRPLANES

III. SUBPART B— TRANSPORT CATEGORY LARGE AIRPLANES AND JET AIRPLANES

(A) Appendix A requirements are nearly identical to those of Appendix 2 of Annex 16 Volume 1, Amendment 7 (See reference 11 of this AC).

(B) Some provisions of Appendix A may also apply to the noise certification of helicopters as prescribed in Appendix H of part 36.

(2) Equivalent Procedures: Equivalent Procedures, as referred to in this AC, are aircraft measurement, flight test, analytical or evaluation methods that differ from the methods specified in the text of part 36 Appendices A and B, but yield essentially the same noise levels. Equivalent procedures must be approved by the FAA. Some equivalent procedures may be the same for all types of aircraft but others may be unique to specific types of aircraft or be proprietary to a particular aircraft manufacturer.

The appended ICAO TM provides both general and technical guidance on equivalent procedures that have been accepted as a technical means for demonstrating compliance with the noise certification requirements of ICAO Annex 16, Volume 1. Section 1 provides guidance material of a general nature including the purpose of the TM, its framework, information on incorporation of equivalent procedures and type design changes into compliance plans and changes to noise levels for derived versions. Section 2 contains technical guidance on equivalent and analytical procedures for subsonic jet airplanes, sections 3 and 4 contain similar guidance for propeller driven airplanes, and section 5 for helicopters. Technical guidance on evaluation procedures is given in section 6. The guidance material provided by the ICAO TM on equivalent procedures that have been approved in the past neither implies that they are the only acceptable ones, nor that they are limited for current noise certification applications, nor that FAA has approved their application for any current or future aircraft noise certification actions (See Supplemental Information Items in Subpart O, section 1501, regarding the FAA’s approval process for equivalent procedures).

Notes: (A) Flight test equivalent procedures have been used to acquire a sufficient number of noise measurements at various engine thrusts (powers) to develop generalized noise databases often referred to as Noise-Power-Distance (NPD) plots. (See section 2.1.2 and 3.1.2 of the appended ICAO TM). These NPD plots may be particularly useful for applicants to determine values of EPNLr for derived versions of an aircraft type.

(B) Equivalent procedures involving the use of static engine noise test data projected to flight conditions to account for changes to an airplane engine configuration or to an installation of an acoustically similar engine on the same airframe have been used for comparison to measured flight noise levels of the airplane with engines as originally certified. This type of data has also been used to demonstrate “no acoustical change” resulting from minor modifications to engine components. (See section 2.3 and 3.3 of the appended ICAO TM).

(C) Equivalent procedures involving analytical methods have been used to determine changes in airplane certificated noise levels resulting from thrust (power) reduction, modifications of airplane maximum takeoff or landing weights, engine thrust (power) rating changes, engine or nacelle configuration or acoustic treatment changes, and airplane performance changes resulting from airframe design changes. (See sections 2.2 and 3.2 of the appended ICAO TM). c. Procedures

(1) Applicant’s Responsibility: Applicants must prepare noise compliance demonstration plans for FAA approval that include proposed methods for compliance with the requirements of Appendix B (See section B36.1). Equivalent procedure proposals in these plans must include substantiation of their technical validity and feasibility of application to the airplane type for which noise certification is requested. (See Subpart O section 1501, Supplemental Information, for noise compliance demonstration plan documentation requirements). 52. Section 36.103 Noise limits

53. Section 36.103(a)

Continue reading ↓ 120 of 559 passages shown