Radar Vectors
Advisory Circular Cancelled Issued Jul 30, 1997 ASW-110 690 pages Copy saved Nov 18, 2026

AC 27-1A Certification of Normal Category Rotorcraft

Provides guidance regarding an acceptable means but not the only means of compliance with Part 27 of the Federal Aviation Regulations (FAR) applicable to certification of normal category rotorcraft. This revision renumbers paragraphs to correspond with FAR numbering. Also, it is divided by Subparts and the page numbers reflect the relevant FAR Subpart. SN 050-007-01279-9

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

Text read by OCR from a scanned file (4 of 690 pages). Check the original, as some words may be misread.

Advisory

U.S.Department ofTransportati

Federal Aviation Administration Circular

Subject: CERTIFICATION OF NORMAL Date: 7/30/97 AC No: 27-1A CATEGORY ROTORCRAFT Initiated by: ASW-110 Change:

1. PURPOSE:

a. This is a total revision of AC 27-1 dated 8/29/85, with changes 1, 2, 3, and 4 dated 9/16/87, 4/24/89, 9/12/91, and 8/18/95 respectively, incorporated. In addition, new material plus changes to existing paragraphs have been incorporated. This consolidated version is now renumbered as AC 27-1A and replaces AC 27-1 in its entirety. This revises existing material in 14 paragraphs and adds new material for 17 paragraphs.

b. This AC does not change regulatory requirements and does not authorize changes in, or deviations from regulatory requirements. This AC establishes an acceptable means, but not the only means of compliance. Since the guidance material presented in this AC is not regulatory, terms having a mandatory definition, such as “shall” and “must,” etc., as used in this AC, apply either to the reiteration of a regulation itself, or to an applicant who chooses to follow a prescribed method of compliance without deviation.

c. This advisory circular provides information on methods of compliance with 14 CFR Part 27, which contains the Aimvorthiness Standards for Normal Category Rotorcraft. It includes methods of compliance in the areas of basic design, ground tests, and flight tests.

2. CANCELLATION. AC 27-1, Certification of Normal Category Rotorcraft, August 29, 1985, is canceled in its entirety.

3. BACKGROUND. Based largely on precedents set during rotorcraft certification programs spanning the past 39 years, this AC consolidates guidance contained in earlier correspondence among FAA headquarters, foreign authorities, the rotorcraft industry, and certificating regions.

4. PRINCIPAL CHANGES:

a. Paragraphs 32, 45, 58, 338, 532, 619, 621, 633, 641, 720, 726, 765, 775, and 777 are revised to incorporate technical guidance.

b. New paragraphs 31A, 58B, 63A, 218B, 218C, 230A, 423B, 447, 454B, 456, 459A, 460B, 563B, 568, 619B, and 724B are added to Chapter 2.

c. New paragraph 781 B is added to Chapter 3,

d. Paragraph 447, ~ 27.951, General, is renumbered to Paragraph 446. Paragraph 447 now addresses ~ 27.952, Fuel System Crash Resistance.

For sde by the U.S. Govenunent Printing ~lce

Superintendent of Documents, Mail Stop SSOP, Washington, DC 20402-9328

ISBN 0-16 -049210-6

e. The following appendix has been added:

Appendix 1 Rotorcraft One-Engine-Inoperative (OEI) Power Assurance

f. Use of the term “FAA/AUTHORITY” replaces “FAA” as appropriate. “FAA/AUTHORITY” as used in this document means FAA or another airworthiness authority that has adopted this AC as a means of compliance with the appropriate regulation referenced.

5. DEVIATIONS. As rotorcraft designs vary from conventional configurations, it may become necessaty to deviate from the methods and procedures outlined in this AC. These procedures are only one acceptable means of compliance with Part 27. Any alternate means proposed by an applicant will be given due consideration. Applicants are encouraged to use their technical ingenuity and resourcefulness to develop more efficient and less costly methods of achieving the objectives of Part 27. Regulatory personnel and designees should respond to such efforts by the use of engineering judgment in fostering any such efforts as long as the letter and spirit of Part 27 and the Federal Aviation Act are respected. It is recommended that unusual or unique projects be coordinated a sufficient time in advance with the Rotorcraft Standards Staff, ASW-I 10, or with the appropriate ainvorthiness authority, to ensure timely and uniform consideration.

6. APPLICABILITY. This material is not to be construed as having any legally binding status and must be treated as advisory only. However, to ensure standardization in the certification process, these procedures should be considered during all rotorcraft type certification and supplemental type certification activities.

7. PARAGRAPHS KEYED TO FAR PART 27. Each paragraph has the applicable amendment to Part 27 shown in the title. All of the original guidance material has been retained as appropriate, even as changes are made to the regulations. This is accomplished through the use of “A,” “B,” etc., paragraphs which follow the original numbered paragraphs. These subsequent paragraphs provide updated guidance information or changes to policy that parallel a specific rule change. The guidance material in the original paragraph (for earlier amendments) still applies and is modified as explained in each of the later paragraphs for later amendments. The applicable amendment number will only appear in the title line for the “A,” “B,” etc., paragraphs. The guidance material in the initial paragraph is intended to apply to all amendments except as modified by the later paragraphs. Each ensuing ‘[A,“ “B,” etc., paragraph will be identified with an amendment level to indicate the rule change that precipitated the policy change.

8. RELAT’ED PUBLICATIONS. FAA Certification personnel and designees should be familiar with Order 8110.4, Type Certification, and Order 8100.5, Aircraft Certification Directorate

Procedures.

Eric Bries Acting Manager, Rotorcraft Directorate

Aircraft Certification Service

7/30/97

TABLE OF CONTENTS

TABLE OF CONTENTS

AC 27-1A

CHAPTER 1- FAR 21 CERTIFICATION PROCEDURES FOR PRODUCTS AND PARTS

Page No.

1.-3. RESERVED 4. FAR21.16 Special Conditions … l 5.-7 RESERVED 8. FAR 21.31 Type Design … 6 9.-11. RESERVED 12. FAR 21.331nspection and Tests … 10 13.-I5.RESERVED 16. FAR21.35 Flight Tests … l4 17.-23. RESERVED 24. FAR 21.39 Flight Test Instrument … 24 Calibration and Correction Report 25.-30. RESERVED

CHAPTER 2- FAR 27 AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT

SECTION 1, GENERAL

31. FAR 27.1 Applicability … 31 31A. FAR27.1 Applicability … 3l 32. FAR 27.2 Special Retroactive Requirements … 3l 33.-41. RESERVED

SECTION 2. FLIGHT - GENERAL

42. FAR27.21 Proof of Compliance … 43 43. FAR27.25 Weight Limits … 44 44. FAR 27.27 Center of Gravity Limits … 46 45. FAR 27.29 Empty Weight and Corresponding Center of Gravity … 48 46. FAR27.31 Removable Ballast … 49 47. FAR 27.33 Main Rotor Speed and Pitch Limits … 49 48.-57. RESERVED

SECTION 3. PERFORMANCE

58. FAR27.45General … 6l 58A. FAR27.45General … 7O 58B. FAR27.45General … 70 59. FAR27.51 Takeoff … 77

Ill

SECTION 3. PERFORMANCE (COntinued)

Page No.

60.-62. RESERVED 63. FAR27.65 Climb: All Engines Operating … 82 63A. FAR27.65 Climb: All Engines Operating … 84 64. FAR27.67 Climb: One Engine inoperative … 84 65. FAR27.71 Glide Petiormance … 85 66. FAR 27.73 Performance at Minimum Operating Speed … 88 67. FAR27.75Landing … 9O 68, RESERVED 69. FAR 27.79 Limiting Height-Speed Envelope … 95 69A. FAR27.79 Limiting Height-Speed Envelope … t O3 70.-79. RESERVED

SECTION 4. FLIGHT CHARACTERISTICS

80. FAR 27.141 General … 114 81. FAR27.143 Controllability and Maneuverability … ll5 82. FAR 27.151 Flight Controls … l20 83. FAR27.161 Trim Control … l2l 84. FAR27.171 Stability: General … l22 85. FAR 27.173 Static Longitudinal Stability … !l22 86. FAR27.1 75 Demonstration of Static Longitudinal Stability … l23 87. FAR27.177 Static Directional Stability … l28 88.-95. RESERVED

SECTION 5. GROUND AND WATER HANDLING CHARACTERISTICS

96. FAR 27.231 General … 138

97. FAR27.235 Taxiing Condition … l38 98. FAR27.239Spray Characteristics … l39 99. FAR 27.241 Ground Resonance … l4O 100.-109. RESERVED

SECTION 6. MISCELLANEOUS FLIGHT REQUIREMENTS

110. FAR 27.251 Vibration … 155

111.-120. RESERVED

SECTION 7. STRENGTH REQUIREMENTS - GENERAL

121. FAR 27.301 Loads … 168

122. FAR27.303Factor of Safety … l68

Iv

7130197 AC 27-1A

SEC ION T 7. STRENGTH REQUIREMENTS -GENERAL (COntinued)

Page No.

123. FAR 27.305 Strength and Deformation … 168 124. FAR 27.307 Proof of Structure … l69 124A. FAR 27.307 Proof of Structure … 170 125. FAR 27.309 Design Limitations … 170 126.-135. RESERVED

SECTION 8. FLIGHT LOADS

136. FAR 27.321 General … 182 137. FAR27.337 Limit Maneuvering Load Factor … l82 138. FAR27.339 Resultant Limit Maneuvering Loads … l85 139. FAR 27.341 Gust Loads … 185 140. FAR27.351 Yawing Conditions … l86 141. FAR 27.361 Engine Torque … 190 142.-151. RESERVED

SECTION 9. CONTROL SURFACE AND SYSTEM LOADS

152. FAR 27.391 General … 2O2 152A. FAR27.391 General … 2O2 153. FAR27.395 Control System … 2O2 153A. FAR 27.395 Control System … 2O4 154. FAR 27.397 Limit Pilot Forces and Torques … 2O4 155. FAR 27.399 Dual Control System … 2O5 156. FAR 27.401 Auxiliary Rotor Assemblies … 2O5 156A. FAR 27.401 Auxiliary Rotor Assemblies … 2O7 157. FAR27.403Auxiliary Rotor Attachment Structure … 2O7 157A. FAR27.403 Auxiliary Rotor Attachment Structure … 2O8 158. FAR27.411 Ground Clearance: Tail Rotor Guard … 2O8 159. FAR 27.413 Stabilizing and Control Surfaces … 2O9 159A. FAR 27.413 Stabilizing and Control Sutiaces … 2ll 160. FAR27.427 Unsymmetrical Loads … 2ll 161.-169. RESERVED

SECTION 10. GROUND LOADS

170. FAR27.471 General … 225 171. FAR 27.473 Ground Loading Conditions and Assumptions … 225 172. FAR27.475 Tires and Shock Absorbers … 226 173. FAR 27.477 Landing Gear Arrangement … 226 174. FAR 27.479 Level Landing Conditions … 226

v

SECTIO N 10, GROUND LOADS (COntinued)

Page No.

175. FAR27.481 Tail-Down Landing Conditions … 227 176. FAR27.483 One-Wheel Landing Conditions … 228 177. FAR27.485Lateral Dfifi Landing Conditions … 228 178. FAR 27.493 Braked Roll Conditions … 229 179. FAR 27.497 Ground Loading Conditions: … 229 Landing Gear With Tail Wheels 180. FAR 27.501 Ground Loading Conditions: … 23l Landing Gear With Skids 180A. FAR 27.501 Ground Loading Conditions: … 232 Landing Gear With Skids 181. FAR 27.505 Ski Landing Conditions … 233 182.-192. RESERVED

SECTION 11. WATER LOADS

193. RESERVED 194. FAR 27.521 Float Landing Conditions … 245 195.-204. RESERVED

SECTION 12. MAIN COMPONENT REQUIREMENTS

205. FAR 27.547 Main Rotor Structure … 258 206. FAR 27.549 Fuselage, Landing Gear, and Rotor Pylon Structure … 258 207.-217. RESERVED

SECTION 13. EMERGENC Y LANDING CONDITIONS

218. FAR27.561 General … 27l 218AFAR 27.561 Emergency Landing Conditions - General … 272 218B. FAR27.561 Emergency Landing Conditions .General … 272 218C. FAR27.561 Emergency Landing Conditions .General … 273 219. FAR 27.562 Emergency Landing Dynamic Conditions … 273 220. FAR27.563 Structural Ditching Provisions … 274 220A. FAR 27.563 Structural Ditching Provisions … 274 221.-229. RESERVED

SECTION 14. FATIGUE EVALUATION

230. FAR 27.571 Fatigue Evaluation of Flight Structure … 285 230A. FAR 27.571 Fatigue Evaluation of Flight Structure for Category A Certification … 288 231.-240. RESERVED

VI

241. 242. 243. 244. 245. 246. 247. 248.

248A.

249. 250. 251. 252. 253.

AC 27-1A

SECTION 15, DESIGN AND CONSTRUCTION - GENERAL

Page No.

FAR27.601 Design … 300 FAR27.603 Materials … 3oo FAR27.605 Fabrication Methods … 3Ol FAR 27.607 Fasteners … 3O2 FAR 27.609 Protection of Structure … 302 FAR27.610 Lightning Protection … 3O3 FAR 27.611 Inspection Provisions … 3O6 FAR27.61 3Matetial Strength Propedies … 3O6 and Design Values FAR27.613 Material Strength Propedies … 3O8 and Design Values FAR27 .619 Special Factors … 3O9 FAR27.621 Casting Factors … 3O9 FAR27.623 Bearing Factors … 3l9 FAR27.625 Fitting Factors … c … 32O FAR 27.629 Flutter … 321

254.-264. RESERVED

SECTION 16. ROTORS

265. FAR27.653 Pressure Venting and Drainage of Rotor Blades … 334 266. FAR27.659 Mass Balance … 334 267. FAR27.661 Rotor Blade Clearance … 334 268. FAR27.663 Ground Resonance Prevention Means … 335 268A. FAR27.663 Ground Resonance Prevention Means … 337 269.-277. RESERVED

SECTION 17, CONTROL SYSTE MS

278. FAR 27.671 General … s … 348

279. FAR 27.672 Stability Augmentation, Automatic … 348 and Power-Operated Systems 280. FAR27.673Ptima~ Flight Control … 349 281. FAR 27.674 Interconnected Controls … 349 282. FAR 27.675 Stops … 350

283. FAR 27.679 Control System Locks … 351

284. FAR27.681 Limit Load Static Tests … 352 285. FAR27.683 Operation Tests … "." … """"""""..353 286. FAR27.685 Control System Details … 353 286A. FAR 27.685 Control System Details … 354 287. FAR 27.687 Spring Devices … 355

288. FAR 27.691 Autorotation Control Mechanism … 355

WI

I

AC 27-1A

SECTION 17. CONTROL SYSTEMS (continued)

7130197

Page No.

289. FAR 27.695 Power Boost and Power-Operated Control System … 356 290.-297. RESERVED

SECTION 18. LANDING GEAR

298. FAR 27.723 Shock Absorption Tests … 367 299. FAR27.725 Limit Drop Test … 37O 300. FAR27.727 Reserve Energy Absorption Drop Test … 37O 300A. FAR27.727 Reserve Energy Absorption Drop Test … 37l 301, FAR 27.729 Retracting Mechanism … < … 37l 302. FAR27.731 Wheels … 374 303. FAR27.733Tires … 375 304. FAR27.735Brakes … 376 305. FAR27.737Skis … 378 306.-315. RESERVED

SECTION 19. FLOATS AND HULLS

316. FAR27.751 Main Float Buoyancy … 39O 317. FAR 27.753 Main Float Design … e … 39o 318. FAR 27,755 HUki … < … 39l 319.-329. RESERVED

SECTION 20. PERSONNEL AND CARGO ACCOM MODATIONS

330. FAR 27.771 Pilot Compartment … 404

331. FAR27.773Pilot CompaRment View … 4O5 332. FAR27.775Wndshields and Wndows … 41 O 332A. FAR 27.775 Windshields and Windows … ! … 410

333. FAR 27.777 Cockpit Controls … 410

334. FAR 27.779 Motion and Effect of Cockpit Controls … 4ll 335. FAR 27.783 Doors … 414

335A. FAR 27.783 Doors … 416

336. FAR 27.785 Seats, Berths, Safety Belts, and Harnesses … 4l6 336A. FAR 27.785 Seats, Berths, Safety Belts, and Harnesses … 42O 337. FAR27.787 Cargo and Baggage Compatiments … 422 337A. FAR 27.787 Cargo and Baggage Compatiments … 424 338. FAR 27.801 Ditching … ! … 424

339. RESERVED 340. FAR 27.807 Emergency Exits … 433

340A. FAR 27.807 Emergency Exits … 434

Vlll

7130/97 AC 27-1A

SECTION 20. PERSONNEL AND CARGO ACCOMMODATIONS(continued)

Page No.

341.-344. RESERVED 345. FAR27.831 Ventilation … 439 346. FAR27.833Heaters … 44O 347.-356. RESERVED

SECTION 21. FIRE PROTECTION

357. RESERVED 358. FAR 27.853 Compartment lntetiors … 454 359. FAR27.855 Cargo and Baggage Compatiments … 455 360. FAR27.859 Heating Systems … 456 361. FAR 27.861 Fire Protection of Structure, Controls, and Other Parts … 460 361A. FAR 27.861 Fire Protection of Structure, Controls, and Other Parts … 462 362. FAR 27.863 Flammable Fluid Fire Protection … 463 363.-372. RESERVED

SECTION 22. EXTERNAL LOAD ATTACHING MEANS

373. FAR27.865 External Load Attaching Means … 475 373A. FAR 27.865 External Load Attaching Means … 476 374.-383. RESERVED

SECTION 23. MISCELLANEOUS (DESIGN AND CONSTRUCTION)

384. FAR27.871 Leveling Marks … 487 385. FAR27.873 Ballast Provisions … 487 386.-396. RESERVED

SECTION 24. POWERPLAN T-G ENERAL

397. FAR27.901 installation … 500 397A. FAR 27.901 Installation … 503

398. FAR27.903 Engines … 5O4 398A. FAR27.903 Engines … 5O6 399. FAR 27.907 Engine Vibration … 508

400.-420. RESERVED

lx

AC 27-1A

SFCTION 75. ROTOR DRIVES STEM Y

7/30/97

Page No.

421. FAR27.91 7Design … 530 422. FAR27.921 Rotor Brake … 53l 423. FAR27.923 Rotor Drive System and Control Mechanism Tests … 532 423A. FAR27.923 Rotor Drive System and Control Mechanism Tests … 537 423B. FAR27.923 Rotor Drive System and Control Mechanism Tests … 538 424. FAR 27.927 Additional Tests … 539 424A. FAR27.927 Additional Tests … 54l 425. FAR 27.931 Shafting Critical Speeds … 54l 426. FAR27.935Shafiing Joints … 546 427. FAR 27.939 Turbine Engine Operating Characteristics … 546 428.-445. RESERVED

SECTION 26. FUEL SYSTEM

446. FAR 27.951 General … 567 447. FAR27.952 Fuel System Crash Resistance … 569 448. FAR27.953 Fuel System independence … 595 449. FAR 27.954 Fuel System Lightning Protection … 596 450. FAR 27.955 Fuel Flow … 597

450A. FAR 27.955 Fuel Flow … 601

451. RESERVED 452. FAR 27.959 Unusable Fuel Supply … 605

453. FAR27.961 Fuel System Hot Weather Operation … 6O5 453A. FAR 27.961 Fuel System Hot Weather Operation … 6O7 454. FAR 27.963 Fuel Tanks: General … 6O7 454A. FAR 27.963 Fuel Tanks: General … 608

454B. FAR 27,963 Fuel Tanks: General … 608

455. FAR 27.965 Fuel Tank Tests … 6O9 456. FAR 27.967 Fuel Tank Installation … 6lO 457. FAR 27.969 Fuel Tank Expansion Space … 6l2 457A. FAR 27.969 Fuel Tank Expansion Space … 6l3 458. FAR 27.971 Fuel Tank Sump … 6l3 458A. FAR 27.971 Fuel Tank Sump … 6l4 459. FAR 27.973 FueITank Filler Connection … 6l5 459A. FAR 27.973 Fuel Tank Filler Connection … 6l5 460. FAR 27.975 Fuel Tank Vents … 616

460A. FAR 27.975 Fuel Tank Vents … 6l8 460B. FAR 27.975 Fuel Tank Vents … 618

461. FAR 27.977 Fuel Tank Outlet … 619

462.-482. RESERVED

x

SFCTION 27. FUEL SYSTEM COMPO NENTS

Page No.

483, FAR 27.991 Fuel Pumps … 641 483A. FAR 27.991 Fuel Pumps … 642 484. FAR 27.993 Fuel.System Lines and Fittings … 642 485. FAR 27.995 Fuel Valves … 643 486. FAR 27.997 Fuel Strainer or Filter … 643 486A. FAR 27.997 Fuel Strainer or Filter … 644 487. FAR 27.999 Fuel System Drains … 645 487A. FAR 27.999 Fuel System Drains … 646 488.-497. RESERVED

SECTION 28, OIL SYSTEM

498. FAR 27.1011 General … 657 499. FAR 27.1013 Oil Tanks O … 657 500. FAR 27.1015 Oil Tank Tests … 658 501. FAR27.1017 Oil Lines and Fittings … 65g 502. FAR 27.1019 Oil Strainer or Filter … 659 502A. FAR 27.1019 Oil Strainer or Filter … 66O 503. FAR 27.1021 Oil System Drains … 66l 504. FAR 27.1027 Transmission and Gearboxes: General … 66l 505.-515. RESERVED

SFCTION 29. COOLING

516. FAR 27.1041 General … 674 516A. FAR 27.1041 General … 676 517. FAR 27.1043 Cooling Tests … 676 518. FAR27.1045 Cooling Test Procedures … 67g 518A. FAR27.1045 Cooling Test Procedures … 68O 519.-530. RESERVED

SEC ION 30, T INDUCTION SYSTEM

531. FAR 27.1091 Air Induction … 693 531A. FAR 27.1091 Air Induction … 694 532. FAR27.1093 Induction System Icing Protection … 694 532A. FAR 27.1093 Induction System Icing Protection … 7O6 533.-547. RESERVED

AC 27-1A

SECTION 31. EXHAUST SYSTEM

7/30/97

Page No.

548. FAR27.1121 General … ! … 722 549. FAR 27.1123 Exhaust Piping … 723 550.-560. RESERVED

SECTION 32, POWERPLANT CONTROLS AND ACCESSORIES

561. FAR 27.1141 Powerplant Controls: General … 737 561A. FAR 27.1141 Powerplant Controls: General … 738 562. RESERVED 563. FAR 27.1143 Engine Controls … !! … 740

563A. FAR 27.1143 Engine Controls … 740

563B. FAR 27.1143 Engine Controls … !.... 741

564. FAR 27.1145 Ignition Switches … l … 74l 565. FAR27.1147 Mixture Controls … 742 566.-567. RESERVED 568. FAR 27.1151 Rotor Brake Controls … ! … 745

569. FAR27.1 163Powerplant Accessories … 746 570.-583. RESERVED

SECTION 33. POWERPLANT FIRE PROTECTION

584. RESERVED 585. FAR27.1183 Lines, Fittings, and Components … 764 586. FAR 27.1185 Flammable Fluids … 764 587. FAR 27.1187 Ventilation … 766

588. FAR 27,1189 Shutoff Means … 767 589. FAR 27.1191 Firewalls … 768

590. FAR27.1193 Cowling and Engine Compartment Covering … 772 590A. FAR27.1193 Cowling and Engine Compartment Coveting … 773 591. FAR 27.1194 Other Surfaces … 774 592. FAR 27.1195 Fire Detector Systems … 775

593.-616. RESERVED

SECTION 34, EQUIPMENT - GENERAL

617. FAR 27.1301 Function and Installation … 8O4

618. FAR 27.1303 Flight and Navigation instruments … 8O4 619. FAR 27.1305 Powerplant Instruments … 805

619A. FAR 27.1305 Powerplant Instruments … 806

619B. FAR 27.1305 Powerplant Instruments … 806

620. FAR 27.1307 Miscellaneous Equipment … 807

X11

7/30/97

SECTION 34. EQUIPMENT - GENERAL (continued)

AC 27-1A

Page No.

621. FAR 27.1309 Equipment, Systems, and installations … 8O8 622.-631. RESERVED

SECTION 35. INSTRUMENTS - INSTALLATION

632. FAR27.1321 Arrangement and Msibility … 836 633. FAR 27.1322 Warning, Caution, and Advisory Lights … 836 634. FAR27.1323 Airspeed Indicating System … 839 635. FAR 27.1325 Static Pressure Systems … 840 636. FAR 27.1327 Magnetic Direction Indicator … ,, … ! … 841 637. FAR27.1329 Automatic Pilot System … 842 638.-639. RESERVED 640. FAR 27.1335 Flight Director Systems … 852 641. FAR 27.1337 Powerplant instruments … 853 641A. FAR27.1337 Powerplant instruments … 854 642.-651. RESERVED

SECTION 36. ELECTRICAL SYSTEMS AND EQUIPMENT

652. FAR27 .1351 General … 866 653. FAR 27.1353 Storage Battery Design and installation … 868 654. RESERVED 655. FAR 27.1357 Circuit Protective Devices … 87l 656.-657. RESERVED 658. FAR27.1361 Master Switch … 875 659. FAR27.1 365 Electtic Cables … 875 660. FAR27.1 367 Switches … 877 661.-667. RESERVED

SECTION 37. LIGHTS

668. FAR27.1381 Instrument Lights … 885 669. FAR27.1383 Landing Lights … 885 670. FAR27.1385 Position Light System installation … 886 671. FAR 27.1387 Position Light System Dihedral Angles … 886 672. FAR 27.1389 Position Light Distribution and intensities … 886 673. FAR 27.1391 Minimum Intensities in the Horizontal … 886 Plane of Forward and Rear Position Lights 674. FAR27 .1393 Minimum Intensities in Any Vetiical … 886 Plane of Forward and Rear Position Lights

X111

AC 27-1A

SFCTION 37. I IGHTS (continued

7130197

Page No.

675. FAR27.1395 Maximum Intensities In Overlapping … 886 Beams of Forward and Rear Position Lights 676. FAR 27.1397 Color Specifications … c … < … 886 677. FAR27,1399 Riding Light … 886 678. FAR27.1401 Anti-collision Light System … 888 679.-688. RESERVED

SECTION 38. SAFETY EQUIPMENT

689. FAR 27.1411 General … 899

690. FAR 27.1413 Safety BeIts … 9ol 691. FAR 27.1415 Ditching Equipment … 9O2 692. RESERVED 693. FAR 27.1419 Ice Protection … ! … 905

694.-701. RESERVED

SEC ION 39 T .MISCELLANEOUS EQUIPMENT

702.-703. RESERVED 704. FAR 27.1435 Hydraulic Systems … 933 705. RESERVED 706. FAR 27.1457 Cockpit Voice Recorder … 937

707. FAR 27.1459 Flight Recorders … 938 708. FAR27.1461 Equipment Containing High Energy Rotors … 94l 709.-717. RESERVED

SECTlO N 40. 0 PERATING LIMITATIONS

718. 719. 720. 721. 722. 723. 724. 724A. 724B. 725. 726. 727. 728.

FAR 27.1501 General … 951

FAR 27.1503 Airspeed Limitations: General … 95l FAR 27.1505 Never-Exceed Speed … 954 FAR 27.1509 Rotor Speed … ! … 956

RESERVED FAR 27.1519 Weight and Center of Gravity … 96O FAR 27.1521 Powerplant Limitations … 96O FAR 27.1521 Powerplant Limitations … 96l FAR 27.1521 Powerplant Limitations … 962 RESERVED FAR 27.1523 Minimum Flightcrew … 965

FAR 27.1525 Kinds of Operations … 969

FAR 27.1527 Maximum Operating Altitude … 969

Xlv

7/30/97

SECTION 40. OPERATING LIMITATIONS (continued

AC 27-1A

Page No.

729. FAR 27.1529 Instructions for Continued Airworthiness … < … 97o (Maintenance Manual) 729A. FAR 27.1529 Instructions for Continued Airworthiness … 972 (Maintenance Manual) 730.-739. RESERVED

SECTION 41. MARKINGS AND PLACARDS

740. FAR27.1541 General … 983 741. FAR 27.1543 Instrument Markings: General … 983 742. FAR 27.1545 Airspeed Indicator … 983 743. FAR 27.1547 Magnetic Direction Indicator … 983 744. FAR27.1549 Powerplant instruments … 983 745. FAR 27.1551 Oil Quantity Indicators … 983 746. FAR 27.1553 Fuel Quantity Indicator … 984 747. FAR27.1555 Control Markings … 985 748. FAR 27.1557 Miscellaneous Markings and Placards … 986 749. FAR 27.1559 Limitations Placard … 987 750. FAR 27.1561 Safety Equipment … 989 751. FAR 27.1565 Tail Rotor … 989 752.-761. RESERVED

SECTION 42. ROTORCRAFT FLIGHT MANUAL

762. FAR 27.1581 General … lool 763. FAR27.15830perating Limitations … l OO9 764. FAR27.1 585 Operating Procedures … l OlO 764A. FAR 27.1585 Operating Procedures … l Ol3 765. FAR27.1587 Performance information … l Ol3 766. FAR 27.1589 Loading information. t … l Ol5 767.-774. RESERVED

CHAPTER 3- MISCELLANEOUS AIRWORTHINESS STANDARDS

775. ~27Appendix B Engineering Flight Test Guide for … lO25 Normal Category Helicopters - Instrument Flight Rules 776. Certification Procedure for Rotorcraft Avionics Equipment … l O46 777. Standardized Test Procedure for Rotorcraft DC … l O62 Electrical System Tests 778. Standardized Test Procedure for Rotorcraft Generator Cooling … 1068 779. Annunciator Panels … lo7o

xv

AC 27-1A 7130197

Chapter 3 (continued)

Page No,

780. Definition of Engine Isolation Features as Applied to … l O72 SS 27.79(b) (2),27 .141(b)(l), and27.143(d)(l) 781. FAR27.1541, 27.1543, 27.1545, and 27.1549 instrument … l O77 Markings 781A. FAR27.1549 Powerplant Markings … l O8l 781B. FAR27.1549 Powerplant MarKngs … l O8l 782.-783. RESERVED 784. Full Authority Digital Electronic Controls (FADEC) for … l O84 Installations with Category A Engine Isolation 785. Agricultural Dispensing Equipment installation … l O86 786. Emergency Medical Service (EMS) Systems, Installations … 1092 Interior Arrangements, and Equipment 787. Hour Meters or Time-in-Service Recording Devices in Rotorcraft … lll O 788. Substantiation of Composite Rotorcraft Structure … lll2

Appendix 1 Rotorcraft One-Engine-Inoperative (OEI) Power Assurance … Al-1

Xvl

Table of ILLUSTRATIONS

ILLUSTRATIONS

The first digits in the figure or table number are the same as the related paragraph

number, The digits after the hyphen are the number within the paragraph. Most figures or tables are located at the end of the related paragraph.

Figure/Table No. m -

58-1 H-V Requirements 71

58-2 IGE Controllability Requirements 72

58-3 Shaft Horsepower vs. Turbine Outlet 73 Temperature - Sea Level Standard Day

58-4 Uninstalled Takeoff Power Available 74

58-5 Installed Takeoff Power Available, Anti-Ice, 75 400 RPM

58-6 Power Assurance Check Chart 76

65-1 Autorotational Characteristics - Typical 87

69-1 Height-Velocity Diagram 101

69-2 Altitude/Weight Accountability 102

86-1 Static Longitudinal Stability 127

110-1 Demonstration Points 157

137-J Load Factor Gross Weight Curve 184

140-1 Sample Yaw/Forward Speed Diagram 189

160-1 View Looking Forward 214

160-2 View Looking Forward 215

230-1 Comparison Percent of Time in Level Flight 287

Xvll

AC 27-1A 7130197

Fiaure/Table No. m E@E

250-1

250-1

331-1

338-1

425-1

425-2

447-1

447-2

447-3

447-4

447-5

447-6

450-1

516-1

589-1

637-1

637-2

Xvlll

Example of Casting Load Sheet Retract Actuator Support-Landing Gear

Table 1: Castings to be Static Tested for Model XYZ

Cockpit Visibility

Sea State Code - World Meteorological Organization

Cantilevered Shaft, First Critical Speed

Shaft Between Support Bearings, First Critical Speed

Static Tension and Shear Loading Modes

Hose Assembly Tests

Minimum Average and Individual Loads for Hose and Hose-End Fitting Combinations

Typical Method of Breakaway Fuel Fitting Load Calculations

Typical Methods of Frangible or Deformable Attachment Load Calculations

Typical Methods of Frangible or Deformable Attachment Load Calculations

Fuel Flow

Additional Cooling Test Point

Table of Materials and Gages Acceptable for Fireproof Protective Devices with Flat Surface Geometries

Deviation Profile

Operational Limitation

316

318

409

431

545

545

589

590

591

592

593

594

600

675

771

848

849

7/30197 AC 27-1A

Fiauremable No. m Paae

693-1 Continuous Icing-Temperature vs. Altitude Limits 919

693-2 Intermittent Icing-Temperature vs. Altitude Limits 920

693-3 Continuous Icing-Liquid Water Content vs Drop 921 Diameter

693-4 Intermittent Icing-Liquid Water Content vs. Drop 922 Diameter

77!5-1 Rotorcraft Dynamic Stability Requirements for IFR 1045

780-1 Engine Isolation Rules 1076

785-1 Acceptable Ultimate Load Factor for Agricultural 1088 Dispensing Equipment Design

785-2 Sketch of Tank Pressure Test 1091

786-1 Typical Liquid Oxygen System 1108

786-2 Typical Liquid Oxygen System - Using 1109 Combination Valve

APXI-I Installed Engine Flow Capacity Check Al-9

X1X

Abbreviations and Definitions

Abbreviations and Definitions

AC advisory circular ACO aircraft certification o~ce ADF automatic direction finding ADI attitude direction indicator AEO all engines operating AFCS automatic flight control systems AGL above ground level AHRS attitude heading reference system Amdt. Amendment APU auxiliary power unit ATC air traffic control BIM blade inspection method CAM cockpit area microphone CAR Civil Air Regulations CAS calibrated air speed CBIM cockpit blade inspection method CDP critical decision point CG center of gravity CPS cycles per second CRFS crash resistant fuel system CRT cathode ray tube CVR cockpit voice recorder DER designated engineering representative DME distance measuring equipment ECAS engine caution advisory systems

ECU environmental control unit EFIS electronic flight instrument system

EFP engine failure point EHE exhaust heat exchanger ELT emergency locator transmitter EMI electromagnetic interference EMS emergency medical service EOL end of life FAA Federal Aviation Administration FADEC full authority digital engine control FAR Federal Aviation Regulations

FMEA failure mode and effects analysis FPM feet per minute FPS feet per second GPS global positioning system HF high frequency HIRF high intensity radiated fields HRD high rate of discharge HUMS health and usage monitoring

systems HV height-velocity IAS indicated airspeed ICAO International Civil Aviation Organization ICS inter-communication system IFR instrument flight rules IGE in ground effect IIDS integrated instrument display system ILS instrument landing system IMC instrument meteorological conditions INS inertial navigation system ISA international standard atmosphere ISIS integral spar inspection system ITT inter-turbine temperature KCAS knots calibrated airspeed KIAS knots indicated air speed KTAS knots true airspeed LDP landing decision point LWC liquid water content MCP maximum continuous power MGT measured gas temperature MSL mean sea level MVD median volume diameter NDI non-destructive inspection NM nautical mile NPRM notice of proposed rulemaking NTSB National Transportation Safety Board NVG night vision goggles

xx

OAT outside air temperature OEI one engine inoperative OGE out of ground effect PBA pitch bias actuator PCF post crash fire PIO pilot induced oscillation PSIG pounds per square inch gauge QPL qualified parts list RFM rotorcraft flight manual RFMS rotorcraft flight manual supplement RPM revolutions per minute RTCA Radio Technical Commission of

Aeronautics RVR runway visual range SAE Society of Automotive Engineers SAS stability augmentation system SCAS stability and control augmentation

systems SRM structural repair manual STC supplemental type certificate STOL short takeoff and landing TBO time between overhaul TC type certificate TCDS type certificate data sheet TDP takeoff decision point TIA type inspection authorization TIR type inspection report TOT turbine outlet temperature TSO: technical standard order TVP true vapor pressure VBIM visual blade inspection method VFR visual flight rules VMC visual meteorological conditions VOR very high frequency omnidirectional

range radio VSI vertical speed indicator V/STOL vertical/short takeoff and landing VTOL vertical takeoff and landing

WAT weight, altitude, temperature

Altitudes

HD density altitude HP pressure altitude

V speeds

VD diving speed VH speed in level flight with maximum

continuous power VMO maximum operating limit speed VNE never-exceed speed VTOSS takeoff safety speed for Category

A rotorcraft VX speed for best angle of climb W speed for best rate of climb MMO maximum operating math number

N speeds

NF free turbine speed NG gas generator speed NP power turbine speed NR rotor speed

Coefficients

CD coefficient of drag CL coefficient of lift CP coefficient of power CT coefficient of thrust

X)(I

CHAPTER 1.

7130197 AC 27-1A

CHAPTER 1. PART 21

CERTIFICATION PROCEDURES FOR PRODUCTS AND PARTS (Amendment 21-50)

1.-3. ~.

4. 621.16 SPECA1 CON I DITIONS.

a. The Process. Chapter 2, Section 1, Paragraph 8 of the Type Certificate Handbook, Order 8110.4, provides detailed guidance on the special conditions process. However, much of that material has been outdated with the implementation of the Aircraft Certification Directorate Program. Rotorcraft special conditions are processed through the Rotorcraft Standards Staff, ASW-I 10. That office will ensure coordination with the affected agency and industry elements including the Assistant Chief Counsel. All comments will be considered and the disposition documented by the Rotorcraft Directorate. ASW-I 00 will issue the special conditions.

b. Basis for Development.

(1) Special conditions are justified on the basis of the existing Part 27 being inadequate or inappropriate due to novel or unusual design features of the rotorcraft to be certificated.

(2) The phrase “novel or unusual” as used in ~ 21.16 is a very relative term. As used hereafter in applying ~ 21.16 to justify the issuance of special conditions, “novel or unusual” will be taken with respect to the state of technology envisaged by the applicable airworthiness standards of this subchapter. It must be recognized that in some areas which will vary from time to time, the state of the regulations may somewhat lag the state of the art in new design because of the rapidity in which the state of the art is advancing in civil aeronautical design and because of the time required to develop the experience base needed by the FAWAUTHORITY to proceed with general rulemaking. Applicants for type certification of a new design have the opportunity to mitigate the impact of not knowing the precise airworthiness standards to be applied for “novel or unusual design features” by consulting with the FAA/AUTHORllY early in their certification planning when such features are suspected or known by the applicant to exist. It should also be recognized that, because of the intentional objective nature of the airworthiness standards of this subchapter, many new design features which might be thought of as “novel or unusual” may already be adequately covered by existing regulations, thus obviating the need to issue special conditions.

(3) Before proposing special conditions, the certification staff should very thoroughly analyze the existing regulations and ensure they are inadequate or inappropriate in light of a new and novel design feature.

Par 4

7/30/97

5.-7. RESERVED.

Par 5

AC 27-1A

Intentionally

Left Blank

3 (thru 5)

8. $$21.31 TYPE DESIGN.

The regulatory basis for requiring data to define the design is contained in $21.31. This section is self-explanatory and broad enough in scope to give the certification staff access to sufficient data to determine compliance with Part 27.

7130197

9.-11. RESERVEQ

Par 9

AC 27-1A

Intentionally

Left Blank

7(thru 9)

12. ~ 21.33 INSPECTION AND TESTS.

a. Atmlicant Res~onsibility. Section 21.33 requires the applicant to:

(1) Ensure the test rotorcraft conforms to the type design. This must be accomplished prior to presentation to the FAAIAUTHORITY for testing.

(2) Conduct all inspections and tests necessary to determine compliance with the airworthiness and noise requirements.

b. FAIVAUTHORITY Respo risibility.

(1) The design evaluation engineers should ensure that the type design is adequate in their technical area and that the inspections and tests to be conducted are appropriate and sufficient to show compliance with Part 27.

(2) As changes to the rotorcraft are made during the test program, the flight test crew should ensure that the appropriate design evaluation engineer concurs with the change and the conformity inspection of the change has been conducted.

Par 12

7/30/97

13.-15. RESERVED.

AC 27-1A

Intentionally

Left Blank

Il(thru 13) Par 13

16. ~21.35( Amendment 21-59) FLIGHT TESTS.

a. Exdanation.

(1) This section outlines the requirements of the applicant for aircraft type certification and should be used in conjunction with Order 8110.4, Section 5. Section 21.35 requires, in part, that the applicant conduct sufficient flight tests to show compliance with the flight requirements throughout the proposed flight envelope. The results of the applicant’s flight test should be submitted to the FANAUTHORITY in report form for evaluation to determine what verification flight tests the FAA/AUTHORITY may elect to conduct. The report should conclude that in the applicant’s opinion the test aircraft complies with the applicable certification requirements. The FWVAUTHORITY verification flight test should include, but not be limited to, the critical or marginal results contained in the applicant’s flight test report. The FANAUTHORITY’S role in the certification effort is not envisioned to be one of conducting day-to-day routine flight tests with the applicant, but only to verify his results through limited sampling. In certain tests, such as high altitude testing at a remote mountain site, there is an advantage in conducting flight tests concurrently with the applicant. Additionally, the FANAUTHORITY can provide technical flight test assistance to the applicant in certain cases. This can be done after a cursory review and a letter of authorization is issued to the flight test crew.

(2) Preflight Test Planninq. After the applicant’s flight test report is reviewed, it should be determined what FANAUTHORITY engineering flight tests are necessary. These tests are normally specified in the Type Inspection Authorization (TIA). At the same time the FANAUTHORITY must know and agree to the applicant’s proposed means of data acquisition, reduction, and expansion of the flight test data. The adequacy of the test instrumentation should be evaluated prior to official type certification tests (reference Paragraph 24).

(3) Order of Testing. The Federal Aviation Regulations are so worded that the results of some flight tests have a definite bearing on the conduct of other tests. For this reason, and to minimize retesting, careful attention should be given to the order of testing. The exact order of testing will be determined only by considering the particular rotorcraft and test program involved. Tests which are particularly important in the early stages of the program are:

(i) Airspeed calibration. All tests involving airspeed depend upon the calibration.

(ii) Engine power available determination.

(iii) Engine cooling.

(4) Test Groupings.

Par lfj

(i) Weight and CG. In addition to the regulatory relationship of one test to another, efficient testing requires that consideration be given to the accomplishment of as many tests on a single flight as can be accommodated successfully.

(ii) Special Instrumentation. Similarly, consideration should be given to grouping of tests that involve special instrumentation. Examples of these are takeoff and landing tests which usually require group equipment to record horizontal distance, height, and time. Ground calibration of the airspeed indicating system can be accomplished at the same time. It is the applicant’s responsibility to provide the necessary instrumentation.

b. Procedures.

(l) T- ~. ii

(i) Prior to initiating official FAWAUTHORITY flight tests, a conformity inspection of the test aircraft must be accomplished. This is needed to ensure that the test aircraft is in the proper configuration or “conforms” to the engineering drawings and documents that have been submitted to FNVAUTHORITY, evaluated, and approved. It is absolutely essential to know the configuration being tested in any engineering flight evaluation. Conformity inspection prior to TIA flight tests assures that testing will not be wasted because of configuration uncertainties.

(ii) Certification Handbook 8110.4, Paragraph 67, contains a requirement that the applicant must keep the FAA/AUTHORITY advised of any configuration changes to the aircraft. The manufacturing inspector should keep the FA4/AUTHORITY flight test pilot apprised of any change which may affect safety of the test aircraft or may influence test results.

(iii) Results of the conformity inspection and the engineering flight test program must be documented. This is normally done in the Type Inspection Report (TIR). Results maybe documented in any acceptable engineering format. The report should be in sufficient detail to clearly show how compliance with each appropriate section of the rule was determined.

(iv) The flight test pilot must ensure that the FANAUTHORITY manufacturing inspector and the certification engineer are aware of all configuration changes found necessary as a result of FANAUTHORITY tests. The manufacturing inspector is responsible for ensuring that all changes are incorporated into production drawings after the design data reflecting the change have been approved by the certification engineer.

(v) Additional flight test responsibilities, procedures, and requirements during the certification flight test process are contained in Certification Handbook 8110.4, Section 5, Flight.

(2) Function and Reliability Tests.

(i) A comprehensive and systematic check of all aircraft components must be made to ensure that they perform their intended function and are reliable.

(ii) Function and reliability (F&R) testing must be accomplished on an aircraft which is in conformity with the approved production configuration. F&R testing should follow the type certification testing described in Paragraph 16b(l ) above to ensure that significant changes resulting from type certification tests can be incorporated on the aircraft prior to F&R tests.

(iii) All components of the rotorcraft should be periodically operated in sequences and combinations likely to occur in service. Ground inspections should be made at appropriate intervals to identify potential failure conditions; however, no special maintenance beyond that described in the aircraft maintenance manual should be allowed.

(iv) A complete record of defects and failures should be maintained along with required servicing of aircraft fluid levels. Results of this record should be consistent with inspection and servicing information provided in the aircraft maintenance manual.

(v) A certain portion of the F&R test program may emphasize systems, operating conditions, or environments found particularly marginal during type certification tests.

(vi) See Handbook 8110.4, Paragraph 166(c), for additional information and procedures.

Par 16

7/30/97

17.-23. RESERVED.

Par 17

AC 27-1A

Intentionally

Left Blank

17 (thru 23)

24. ~ 21.39 (Amendment 21-59) FLIGHT TEST INSTRUMENT CALIBRATION AND CORRECTION REPORT.

a. Explanation. It is the applicant’s responsibility to provide instrumentation for all parameters needed to show compliance with the airworthiness regulations.

(1) For those data which are necessary to show compliance with the regulations, a permanent record should be established. A permanent record is acceptable in either graphical or photographic form, and in some instances a manual recording may be satisfactory.

(2) Regardless of the record form, the accuracy of the record must be established by reference to a laboratory standard traceable to the National Bureau of Standards,

(3) If multiplexing is used, the time base must be synchronized to a reference point from which the magnitude of each parameter can unquestionably be determined. Also, the sampling rate should be sufficiently frequent to ensure that the maximums, minimums, and trends of magnitude of the parameter are recorded with respect to time.

b. J30ce-. Prior to conducting flight tests, the FANAUTHORITY flight test team should review the applicant’s flight test instrumentation, calibration, and correction report.

(1) The frequency of recalibration varies with the consistency of the instrumentation under consideration. For example, cyclic and collective position is sometimes calibrated immediately before and after a flight where these parameters are used to provide critical flight data. Six months is a typical interval for recording/signal conditioning and nonstrain gage sensors, while one year is typical for strain gaged components. Also, environmental effects such as vibration, humidity, temperature, etc., should be considered when determining whether recalibration is necessary.

(2) The highest and lowest magnitude of the parameter being recorded should be considered when establishing the scale for instrumentation. Ideally, the highest magnitude throughout the flight would fall on the maximum indicating point of the recording.

25.-30. RESERVED.

24 (thru 30) par 24

CHAPTER 2. › SECTION 1. GENERAL

CHAPTER 2. PART 27 AIRWORTHINESS STANDARDS NORMAL CATEGORY ROTORCRAFT

SECTION 1. GENERAL

31. ~ 27.1 APPLICABILITY.

a. Explanation. This section prescribes the rotorcraft categories eligible for certification under this Part. There is no minimum weight limit for certification under Part 29; however, Part 27 is applicable to rotorcraft with maximum weights of 6,000 pounds or less.

(1) Without Engine Isolation. For single-engine rotorcraft and multiengined rotorcraft without engine isolation, the height-velocity (HV) diagram is conducted with sudden failure of all engines, and the takeoff maneuver must pass through the clear area of the diagram to the 50-foot point with all engines operating.

(2) With Engine Isolation. Part 27 multiengined rotorcraft may be certificated with engine isolation features (reference Paragraph 780 of this AC). These rotorcraft are not required to meet the Part 29, Category A, performance requirements, and continued flight after an engine failure is not assured since under some conditions failure of the remaining engine may occur after a limited time. The takeoff is conducted with all engines operating, while the height-velocity diagram is determined with the most critical engine inoperative. If complete Part 29, Category A, design features and performance are achieved, the Category A performance may be included in the FAA/AUTHORITY-approved portion of the Rotorcraft Flight Manual although this performance is not required by the regulations.

b. Procedures. None.

31A. ~ 27.1 (Amendment 27-33) APPLICABILITY.

a. Explanation. Amendment 33 formally introduced the requirements for certification of a Part 27 rotorcraft to Category A design and performance standards. These standards are found in Appendix C of Part 27. The establishment of Category A design and performance for multiengined Part 27 rotorcraft is still voluntary. If so requested, the corresponding AC 29-2A material applies.

b. Procedures. None

32. 627.2 (Amendment 27-28) SPECIAL RETROACTIVE REQUIREMENTS.

a. Exoianation.

AC 27-1A 7130197

(1) Amendment 27-28 requires a combined shoulder harness and safety belt (also called a torso restraint system) at each occupant’s seat for all rotorcraft manufactured after September 16, 1992.

(2) The design features of the restraint system are mainly contained in this section rather than having to refer to other sections within Part 27 except for a general reference to the differing strength standards between earlier static strength only standards and the static and dynamic strength standards of Amendment 27-25.

(3) Combined safety belt and harness strength standards system follows:

(i) Those rotorcraft type designs certificated to static strength standards alone prior to Amendment 27-25, such as 4 g’s forward may use belt and harness systems, characterized as 1,500 pounds strength systems, provided they comply with those standards. TSO C22f and earlier restraint systems have such ratings. A combined belt and harness with a 1,500 pounds rating, which comply with the Part 27 standards for the rotorcraft type design, but are not necessarily TSO approved, may be approved as a part of the type design. Such design information for a non-TSO’d item would be included in a note on the aircraft type certificate data sheet (TCDS) or specification sheet by part number as “required equipment. ” TSO Cl 14-approved torso restraint systems, characterized as 3,000 pounds strength system, may be used provided the design features comply with this section, but no special information on the TCDS is necessary.

(ii) Those rotorcraft type designs certified to dynamic test requirements of Amendment 27-25 should use torso restraint systems approved under TSO Cl 14 or approved under equivalent standards such as those contained in Part 27.

(4) Load Distribution and Desian Requirements. Although not stated in $27.2, a 60 percent and 40 percent load distribution between the safety belt and harness, respectively, is required in $ 27.785(g). The safety belt should withstand 100 percent if the” safety belt is capable of being used alone. Also, the safety belt or harness attachments to the seat or structure should include the 1.33 factor described in ~ 27.785(f)(2) of Amendment 27-21 for those rotorcraft with that certification criteria should include the 1.15 factor as described in ~ 27.625 (and predecessor Part 6) standards for those rotorcraft with the earlier certification criteria. A factor is used whether test or analysis methods are used for static substantiation of the seating systems. Refer to Paragraph 336b, (~ 27.785), of this AC.

or

(5) The companion operating rule change of Amendment 91-220, amended $91.205 (Amendment 91-223), affecting the aircraft equipment requirements. Operating rule ~ 91.107(a) already requires use of the harness whenever the aircraft seat is so equipped.

7130197 AC 27-1A

b. Procedures.

(1) A TSO-approved combined safety belt and harness or torso restraint system may be used provided the installation requirements in $j 27.2 are satisfied. A combined belt and harness (not necessarily TSO approved) may be approved as a part of the rotorcraft type design and so noted on the aircraft specification or TCDS.

(2) Structural analysis or static test maybe used. For those rotorcraft designs that are subject to the dynamic test standards of ~ 27.562, the torso restraint system is required to be qualified for the particular use or installation in each rotorcraft type design. A dynamic test maybe required for alternate restraint systems as well as the originally approved system. TSO Cl 14 approval does not constitute approval for installation of a restraint system in a rotorcraft design subject to dynamic test.

(i) AC 20-137 dated March 30, 1992, concerns in part the dynamic test standards of Amendment 27-25.

(ii) AC 23-4 dated June 20, 1986, concerns static test procedures for small airplane seats and restraint systems. (Certain small airplanes manufactured after December 12, 1986, should have harnesses for each seat also.) A test proposal for rotorcraft installations may adopt procedures appropriate to the particular installation, The 60/40 percent distribution is sufficiently achieved when the blocks in Figure 4 of AC 23-4 are used.

(iii) The static design side load for the harness installation may be proven by test or analysis using the load distribution previously noted. For “older” designs, the side load of S 27.561 (b)(3) (iii) is 2.Og, and for later designs (Amendment 27-25 and later), it is 8.Og.

AC 27-1A

33.-41. RESERVED.

7/30/97

Intentionally

Left Blank

Par 33 34(thru 42)

CHAPTER 2. › SECTION 2. FLIGHT - GENERAL

7130197

SECTION 2. FLIGHT - GENERAL

AC 27-1A

42. $27.21 (Amendment 27-21) PROOF OF COMPLIANCE.

a. Extianation.

(1) This section provides a degree of latitude for the FAA/AUTHORITY test team in selecting the combination of tests or inspections required to demonstrate compliance with the regulations. Compliance should be shown for applicable combinations of gross weight, center of gravity, altitude, temperature, airspeed, rotor RPM, etc. Engineering tests are designed to investigate the overall capabilities and characteristics of the rotorcraft throughout its operational envelope. Testing will identify operating limitations, normal and emergency procedures, and performance information to be included in the FAA/AUTHORITY-approved portion of the flight manual. The testing must also provide a means of verifying that the rotorcraft’s actual performance, structural design parameters, propulsion components, and systems operations are consistent with all certification requirements.

(2) Section 21.35 requires, in part, that the applicant show compliance with the applicable certification requirements, including flight test, prior to official FAA Type Inspection Authorization (TIA) testing. Compliance in most cases requires systematic flight testing by the applicant. After the applicant has submitted sufficient data to the FAA/AUTHORITY showing that compliance has been met, the FAA/AUTHORITY will conduct any inspections, flight, or ground tests required to verify the applicant’s test results. FAA/AUTHORITY compliance may be partially determined from tests conducted by the applicant if the configuration (conformity) of the rotorcraft can be verified. Compliance may be based on the applicant’s engineering data and a spot check or validation through FAA/AUTHORITY flight tests. The FAWAUTHORITY testing should obtain validation at critical combinations of proposed flight variables if compliance cannot be inferred using engineering judgment from the combinations investigated.

(3) Performance tests include minimum operating speed (hover), takeoff and landing, climb, glide, height-velocity, and power available. Certain other performance tests, such as critical engine survey for multiengined installations, may be conducted to meet specific requirements. Detailed performance test procedures and allowable extrapolation or simulation limits are contained in the respective Paragraphs in this AC.

(i) Hover tests are conducted to determine various combinations of altitude, temperature, and gross weight for both in-ground-effect (lGE) and, if required by the applicant, out-of-ground effect (OGE) conditions. From these data, the hover ceiling may be calculated.

AC 27-1A 7130197

(ii) Takeoff and landing tests are conducted to determine that a takeoff or landing can be safely executed without requiring exceptional piloting skill or favorable conditions at any approved combination of altitude, temperature, and gross weight.

(iii) For rotorcraft other than helicopters, climb tests establish the variations of rate-of-climb at the best rate-of-climb or published climb airspeed(s) at various combinations of altitude, temperature, and gross weight. For helicopter, climb tests are conducted as required to determine the best rate-of-climb speed, VY.

(iv) Height-velocity tests are conducted to determine the boundaries of the height versus airspeed envelope from which a safe landing can be accomplished following an engine failure.

(v) Power available tests are conducted to verify the calculated installed specification engine performance model on which published performance is based.

(4) The purpose of rotorcraft stability and control tests is to verify that the rotorcraft possesses the minimum qualitative and quantitative flying qualities and handling characteristics required by the applicable regulations. In order to assess the handling qualities, standardized test procedures must be utilized and the results analyzed by accepted methods. Section 27.21(a) allows calculation and inference which includes extrapolation and simulation, whereas S 27.21(b) requires demonstration of controllability, stability, and trim. Combinations of ~ 27.21 (a) and (b) may be used to show compliance with the operating envelope limits. Test methods and equipment are described in individual paragraphs of this advisory circular.

b. Procedures.

(1) Efforts should begin early in the certification program to provide advice and assistance to the applicant to ensure coverage of all certification requirements. The applicant should develop a comprehensive test plan which includes the required instrumentation.

(2) The tests and findings specified in Paragraph 42a(3) are required of the applicant to show basic airworthiness and probable compliance with the minimum requirements specified in the applicable regulations. After these basic findings have been submitted and reviewed, a Type Inspection Authorization, or equivalent, can be issued. The FAA/AUTHORl~ will develop a systematic plan to spotcheck and confirm that compliance with the regulations has been shown. The test plan will consider combinations of weight, center of gravity, and RPM and cover the range of altitude and temperature for which certification is requested.

43. ~ 27.25 (Amendment 27-14) WEIG HT LIMITS.

a. Exdanation.

(1) This section is definitive and specifies criteria for establishing maximum and minimum certificating weights. These weights may be based on those selected by the applicant, design requirements, or the limits for which compliance with all applicable flight requirements has been shown.

(2) Typical requirements that may establish the maximum and minimum weight limits include:

(i) Maximum: Structural limits, performance requirements, stability, and controllability requirements.

(ii) Minimum: Autorotative rotor RPM, stability, and controllability requirements.

(3) Jettisonable External Carao.

(i) Section 27.25(c) was added by Amendment 27-11 to provide a basis for approving an increased gross weight that would be an external jettisonable load. Section 27.865, “External load attaching means, “ includes hoist and hook design features for the load attaching devices that were added to Part 27 but removed from ~ 133.43. Part 133, “Rotorcraft External-Load Operations,” was also amended (Amendment 133-5) concurrently to complement the changes to Parts 27 and 29.

(ii) Approvals under the policy in Review Cases Nos. 37 and 55 of FAA Order 8110.6 were no longer necessary. These review cases concerned the policy/standards for external cargo configurations using a cargo hook whenever the standard limitations were exceeded. If the standard limitations were not exceeded, external cargo hooks and hoists and external cargo configuration approvals could be made under Part 133, Subpart D, prior to Amendment 133-5.

(iii) In the preamble of Amendment 27-11 (Proposal 2-99,41 FR 55454; December 20, 1976) the agency stated that “...~ 27.25(c) and ~ 29.25(c) are intended to provide only a total weight standard for approving the rotorcraft structure for operation under Part 133.” The policy in Review Case No. 55 also indicates the powerplant or propulsion system is also subject to evaluation for the increased weight. As indicated in ~ 27.865, fatigue substantiation of the external cargo attaching means is not required. The rotorcraft structure, rotors, etc., are only subject to fatigue evaluation under $27.571 whenever the standard structural limitations are exceeded (Review Case No. 55).

(iv) Whether or not the standard limitations are exceeded, the flight characteristics evaluations/standards of ~ 133.41 are appropriate even for engineering approval. Section 133.41 is also appropriate for the individual operator to obtain his operating certificate. The operator may use an FAA/AUTHORITY approved RFM

supplement to prepare his own rotorcraft load combination flight manual required by ~ 133.47.

b. ~.

(1) It may not be possible to requirements at the minimum weight

demonstrate quantitatively all the flight because of test instrumentation requirements. The test team must ensure that the rotorcraft complies with the applicable requirements at the lowest permissible flying weight. This evaluation may be done qualitatively with the test instrumentation removed and with minimum crewmembers if no critical areas exist or are anticipated. Additionally, reasonable extrapolation is permitted. However, if critical areas at minimum flying weights are apparent, extrapolation should not be permitted.

(2) Whenever a gross weight increase under $ 27.25(c) is requested, a TIA evaluation is necessary to evaluate the new limitations and ensure that $133.41 for typical or representative cargo weights and/or shapes (or density) is satisfactory. All possible combinations of weights and shapes are not evaluated. The representative configurations may be noted in the RFM or RFM Supplement for the operator’s information. Sections 133.41 and 133.47 must be satisfied by the individual operator for the particular case at hand. The approved RFM or RFM Supplement should provide the necessary limitations and any other information about the representative cargo configurations evaluated. Section 133.41 also permits the operator to obtain approval of additional and unique cargo configurations provided approved limitations are observed. Paragraph 762 of this AC concerns the RFM and its contents.

(3) See AC 29-2, Certification of Transport concerning ~ 29.571, for fatigue substantiation and apply to ~ 27.571 as well.

Category Rotorcraft Paragraph 230, external cargo considerations that

(4) Refer to AC 133-1A, Rotorcraft External-Load Operations in Accordance with FAR Part 133, for further information on airworthiness and flight manual policy for operators.

44. ~ 27.27 (Amendme nt 27-2) CENTER OF GRAVITY LIMITS.

a. Explanat ion.

(1) This regulation is definitive and requires that the center of gravity limits be defined. Proof of compliance with all applicable flight requirements is required within the range of established CG’S. Along with the longitudinal CG limits, the lateral CG limits should either be established or determined to be not critical.

(2) Ballast is usually carried during the flight test program to investigate the approved gross weight/center of gravity limits. Lead is the most commonly used form of

ballast during rotorcraft flight testing although other types of ballast, such as water, may serve just as well. Water may have the added benefit of being jettisonable during critical flight test conditions. Care must be taken regarding the location of ballast. The strength of the supporting structures should be adequate to support such ballast during the flight loads that may be imposed during a particular test and for the ultimate inertia forces of ~ 29.561 (b)(3). Of critical importance is the method of securing the ballast to the desired lGcations. To avoid any undesired in-flight movements of the ballast, a positive method of constraint is mandatory. The flight test crews should also visually verify the amount, location, and integrity of the ballast. The effects of mass moment of inertia on the flight characteristics due to the ballast locations should also be considered. The mass moment of inertia of the test rotorcraft should, to the extent possible, be the same as that expected in normal, approved loadings, especially during tests involving dynamic inputs.

b. Procedures.

(1) Center of gravity locations and limits are of prime importance to rotorcraft stability and safety in flight. The primary concern is establishment of the longitudinal center of gravity limits. Lateral center of gravity limits with respect to longitudinal center of gravity limits are also important. The design of the rotorcraft is usually such that approximate lateral symmetry exists. This lateral symmetry can be upset by numerous probable lateral loadings possibly resulting in the necessity to establish lateral center of gravity limits. Stability and control characteristics may be seriously affected by loading outside the established center of gravity limits. The established center of gravity limits must be that as fuel is consumed, it is possible for the rotorcraft to remain within the established limits by acceptable loading and/or operating instructions.

(2) Structural limits may restrict the maximum forward longitudinal center of gravity limits. However, in most cases it is the maximum value established wherein adequate low speed control power exists to meet such requirements as ~ 27.143(c). Likewise, the maximum aft center of gravity limit maybe a “structural limit,” but it usually is determined during flight test after the rotorcraft’s handling qualities tests have been conducted. Flight tests may reduce the “structural limit” CG envelope, but flight tests alone should not be used to expand the “structural limit.” Additional items which may influence the maximum aft center of gravity limits may be malfunctions of automatic stabilization equipment, excessive rotorcraft attitudes during critical phases of flight, or adequate control power to compensate for an engine failure,

(3) Lateral center of gravity limits have become more critical because of the ever increasing utilization of the rotorcraft for such things as unusual and unsymmetric lateral loads, both internal and external. Maximum allowable lateral center of gravity limits have also influenced the results of the unusable fuel determination.

(4) In summary, it is of prime importance that longitudinal and lateral center of gravity limits be determined so that unsafe conditions do not exist within the approved

Par 44

I

AC 27-1A 7130197

altitude, airspeed, ambient temperature, gross weight, and rotor RPM ranges. All relevant malfunctions must be considered.

45. 627.29 (Amendment 27-14) EMPTY WEIGHT AND CO RESPONDING CENTER OF GRAVITY.

a. Explanation. The empty weight of the rotorcraft consists of the airframe, engines, and all items of operating equipment that have fixed locations and are permanently installed in the aircraft. It includes fixed ballast, unusable fuel, and full operating fluids except water intended for injection in the engines.

(1) Fixed ballast refers to ballast that is made a permanent part of the rotorcraft as a means of controlling the empty weight CG.

(2) Compliance with Paragraph (b) of $27.29 is accomplished by the use of an equipment list which defines the installed equipment at the time of weighing and the weight arm and moment of the equipment.

b. Procedures.

(1) Determination of the empty weight and corresponding center of gravity is primarily the responsibility of the manufacturing inspector. This determination is normally made on the production rotorcraft rather than the prototype. If the manufacturer wishes to avoid the necessity of weighing each production rotorcraft and he has been issued a production certificate, he may make a detailed proposal defining the procedures he will use to establish an empty weight and CG When his proposal is approved, he will weigh the first five to ten production rotorcraft and show that the rotorcraft will be within *I percent on empty weight and *0.2 inches on CG After this procedure is established, the empty weight and CG maybe computed except that at regular intervals, a rotorcraft will be weighed to ensure the tolerances are still being maintained; e.g., one in ten rotorcraft.

(2) For prototype and modified rotorcraft, it is only necessary to establish a known basic weight and CG position (by weighing) from which the extremes of weight and CG travel required by the test program may be calculated. See AC 91-23 (Pilots Weight and Balance Handbook) for a sample weight and balance procedure.

(3) The weight and balance should be recalculated if a modification (or series of modifications) to the rotorcraft results in a significant change to the empty weight. Additionally, this change in empty weight should be reflected with the weight and balance information contained in the Rotorcraft Flight Manual (RFM) or Rotorcraft Flight Manual Supplement (RFMS).

c. Ballast Load ina and Type.

Par 44

7130197 AC 27-1A

(1) Ballast loading of the rotorcraft can be accomplished in any manner to achieve a specific CG location. It is acceptable for such ballast to be mounted outside the physical confines of the rotorcraft if the flight test objectives are not affected by this arrangement. In flight test work, loading problems will occasionally be encountered in which it will be difficult to obtain the desired CG limits. Such cases may require loading in engine compartments or other places not designed for load carrying. When this condition is necessary, care should be taken to ensure that local structural stresses are not exceeded or that the rotorcraft flight characteristics are not changed due to increased moments of inertia by attaching the ballast to extreme CG locations which may not be designed for the added weight.

(2) There are basically two types of ballast that maybe used in loading. They are solids or liquid. The solids are usually high density materials such as lead while the liquid usually used is water. In critical tests, the ballast may be loaded in a manner so that disposal in flight can be accomplished. In any case, the load should be securely attached in its loaded position so shifting or interference with safety of flight will not result.

46. $27,31 REMOVABLE BALLAST.

a. Exdanat ion. This regulation provides the option of using removable ballast to obtain desired center of gravity locations to determine compliance with the flight requirement of this Part. Fixed ballast used for flight operations after type certification must be documented in the type design data. Removable ballast is used primarily on small rotorcraft to control the CG with different passenger loadings although this regulation does not permit its use on transport rotorcraft. If removable ballast is used, the rotorcraft flight manual must include instructions regarding its use and limitations.

b. Procedures. None

47. ~ 27.33 (Amendment 27-14) MAIN ROTOR SPEED AND PITCH LIMITS.

a. Exdanation.

(1) Genera! This section requires the establishment of power-on and power-off main rotor speed limits and the requirements for low rotor speed warning.

(2) Power-On. The power-on limits should be sufficient to maintain the rotor speed within these limits during any appropriate maneuver expected to be encountered in normal operations throughout the flight envelope for which certification is requested. In the pasta minimum power-on range of approximately 3 percent has been required due to engine governor and engine operating characteristics. With the introduction of advanced engines and electronic engine controls, there may not be a need for a range. One fixed value may suffice. If substantiated, transient power-on values may also be acceptable.

AC 27-1A 7130197

(3) Power-Off. The power-off rotor speed limits should be sufficient to encompass the rotor speeds encountered during normal autorotative maneuvers except for final landing phase (touchdown) for which rotor RPM may be lower than the minimum transient limit for flight, provided stress limits are not exceeded. The limits should also be sufficient to cover the ranges of airspeed, weight, and altitudes for which certification is requested. It is not the intent of the rule to require the minimum and maximum limit values in conjunction with extremes such as maximum/minimum weights and/or high altitude. The minimum and maximum rotor speed requirements should be thoroughly evaluated at normal operating environment; i.e., at altitudes from approximately sea level to 10,000 feet, temperatures not at extremes, and weights as necessary for other tests and as required to readily establish the limit rotor speeds. Spot checks of the autorotative requirements should be made at the extremes of the flight envelope and environmental conditions during normal tests at those conditions.

Under conditions where high autorotative rotor speeds may be encountered, it is acceptable for the pilot to adjust the controls to prevent overspeeding of the rotor. At light weight combined with low altitudes and extremely cold temperatures, the normal low pitch setting may not be sufficient to maintain autorotational rotor speed values within limits. If this occurs, the manufacturer may elect to adjust the low pitch stops as a maintenance procedure at extreme ambient conditions provided the flight and maintenance manuals clearly present the rigging requirements and procedures. There must be sufficient “overlap” of ambient conditions between configurations such that rerigging is not required whenever ambient temperature and surface elevation change slightly. Any downrigging of the low pitch stop must continue to ensure adequate clearance between controls and other rotorcraft structure and should be evaluated during flight test.

Both the power-on and power-off limits may also be established by encountering critical flapping limits in some approved flight conditions such as high airspeed or sideward flight.

(4) Low Speed Warninq. If it is possible under expected operating conditions for the rotor speed to fall below the minimum approved values, the requirement exists for a low rotor speed warning. This warning is required on all single-engine rotorcraft and on multiengined rotorcraft where there is not an automatic increase in remaining engine(s) power output upon failure of an engine. Although not required by the rule, essentially all of today’s multiengined rotorcraft have a low rotor speed warning system installed. If the minimum power-on and power-off rotor speed limits are different, the warning signal should be at the higher speed, normally the power-on minimum rotor speed. One type of rotorcraft has a warning system cutout if the collective is full down, and other types have other warnings on the engine speed to indicate engine failure. All of these related warning systems must be evaluated with emphasis on ensuring adequate rotor speed.

b. Determination and Test ing. Refer to Paragraph 721 (S 27.1509) for additional information on determining and testing rotor limits.

7/30/97

48.-56. ~.

FkN 48

AC 27-1A

Intentionally

Left Blank

51 (thru 59)

AC 27-1A

57. RESERVED.

7/30/97

Intentionally

Left Blank

AC 27-1A

SECTION 3. PERFORMANCE

CHAPTER 2. › SECTION 3. PERFORMANCE

58. S 27.45 (Amendment 27-21) GENERAL,

a. Exc)lanation.

(1) Section 45 of Part 27 lists some of the rules and standards under which the performance requirements are to be met. This paragraph will provide general guidelines that may be used throughout a flight test program. It is impossible to find ideal test conditions and there are many variables which affect the flight test results that must be taken into account. Some of these variables are wind, temperature, altitude, humidity, rotorcraft weight, power, rotor RPM, center of gravity, etc. A thorough knowledge of the testing procedures and data reduction methods is essential and good engineering judgment must be used to determine acceptable test conditions. The test results should be analyzed and expanded by approved methodology within the guidelines of this paragraph.

(2) Performance should be based on approved engine power as determined in Paragraph b(5) below and not on any transient limits. Approved transient limits are basically for inadvertent overshoots of approved operational limits and any sustained operation in these transient limit areas usually requires some form of special maintenance. However, for such demonstrations as landing procedure demonstration and height-velocity (HV) determination, low rotor speeds (within approved limits) have been authorized. Such transients, if authorized, must be flight evaluated.

(3) Where variations in the parameter on which a tolerance is allowed will have an appreciable effect on the test, the results should be corrected to the standard value of the parameter; otherwise, no correction is necessary.

b. mcedures.

(1) Winds for Testing.

(i) Allowable wind conditions will vary with the type of test and will also be different for different types and gross weight rotorcraft. For example, higher winds can usually be tolerated for takeoff and landing tests than for hover performance. Higher winds can sometimes be tolerated during hover performance testing on rotorcraft with high rotor downwash velocities. Generally, unless the effects of wind on hover performance tests can be determined and/or accounted for, hover performance testing should be conducted in winds of 3 knots or less.

(ii) In-ground-effect controllability and maneuverability testing should be conducted in surface winds of less than 5 knots, or when higher steady wind conditions exist, with a maximum gust spread of 5 knots.

(iii) As can be seen from the foregoing, there is no such thing as an exact allowable wind for a particular test or rotorcraft. The flight test team must decide on the allowable wind for each condition based on all available information and their engineering judgment. The following summary of allowable wind conditions is given for general guidance only:

(A) (B) (c)

Hover performance -0 to 3 knots. Height-velocity -0 to 3 knots. IGE controllability and maneuverability -0 to 5 knots.

(iv) A means should be provided to measure the wind velocity, direction, and ambient air temperature at the rotor height for any particular tests.

(2) Altitude Effects. Using FAA/AUTHORITY-approved methodology, hover performance may be extrapolated and/or interpolated from test data up to a maximum of *4,000 feet. Experience has shown that IGE handling qualities, height-velocity, and engine operating characteristics should not be extrapolated higher than approximately 2,000 feet density altitude from the test altitude. Cruise stability/controllability tests should be evaluated at least at two different altitudes, the lowest practical altitude and approximately the highest cruise altitude requested for approval. This can allow an interpolation of approximately 10,000 feet. As in all testing, extrapolation and/or interpolation should only be considered if all available information and engineering judgment indicate that regulatory compliance can be met at the untested conditions.

(3) M itude Limitations.

(i) Explanation..

(A) Two altitudes are normally presented in the RFM to define the operating envelope of a rotorcraft;

- Maximum operating altitude, and - Maximum takeoff and landing altitude.

(B) Maximum operating altitude is an operating limitation required by ~ 27.1527 and delineates the maximum altitude to which operation is allowed. This altitude normally constitutes the maximum cruise or en route altitude.

(C) Maximum takeoff and landing altitude is the hover in-ground-effect (lGE) ceiling for a rotorcraft as described in ~ 27.73. The hover ceiling and any information pertinent to takeoff and landing are presented in the performance information section of the RFM. For rotorcraft certified to CAR 6, Amendment 6-7 or any amendment of FAR 27, a hover ceiling may not be presented above the altitude at which H-V and IGE controllability tests were conducted plus allowable extrapolation,

unless that extrapolated altitude is at least 7,000 feet. If the applicant elects to demonstrate these tests to an altitude below 7,000 feet, then that altitude is the maximum takeoff and landing altitude of the rotorcraft. The maximum takeoff and landing altitude may be coincident with, but never above the maximum operating altitude limitation. Takeoff and landing and hover ceiling data and presentation requirements are presented in $$27.51, 27.73 and 27.1587.

(ii) Procedures.

(A) In establishing the maximum takeoff and landing altitude, the following tests are normally required:

(1)

(2)

(3)

(4)

(5)

(6)

(z)

(a

Takeoff ($j27.51 )

Climb (fj$j 27.65 and 27.67)

Performance at minimum operating speed ($ 27.73)

Landing (~ 27.75)

Limiting height-speed envelope ($ 27.79)

IGE controllability (~ 27.143c)

Cooling (~$j 27.1041, 27.1043 and 27.1045)

Engine operating characteristics (~ 27.939)

Specific guidance on test methodology and data requirements is provided in applicable paragraphs of this AC.

(B) As detailed in subparagraph b(2) above, the maximum allowable extrapolation of H-V, IGE controllability and engine operating characteristics is *2,000 feet. Therefore, the maximum takeoff and landing altitude presented in the RFM is not normally more than 2,000 feet above the density altitude experienced at the high altitude test site, or for CAR 6, Amendment 6-7 and subsequent, unless test results were demonstrated to at least 7,000 feet.

(C) If IGE controllability is demonstrated to at least 17 knots of wind at 7,000 feet, hover capability above 7,000 feet may be presented provided that the maximum demonstrated safe wind for takeoff and landing above 7,000 feet is specified in the RFM.

(D) The requirements for data collection and presentation in the RFM vary depending upon the certification basis of the rotorcraft. These requirements are presented by regulation and amendment in Figures 58-1 and 58-2.

(E) The maximum takeoff and landing altitude may be extrapolated no greater than the values given in Paragraph b(2) and not above the lowest limiting altitude resulting from the requirements of subparagraph A of this paragraph.

(4) Temperature Effects.

(i) Background.

(A) In the past, approved analyses were frequently accepted for determining the extreme temperature effects on performance and flight characteristics. With the introduction of newer, higher performance rotorcraft, advanced rotor blade designs, higher airspeeds, and higher blade tip Mach numbers, the previous methods have proven to be insufficient. Therefore, the performance and flight characteristics should be validated at extreme temperatures; however, analysis may be permitted if a suitable methodology is demonstrated.

(B) Various FANAUTHORITY cold weather programs have verified that rotorcraft can be affected by cold temperature in both the performance and flying qualities areas. Hot temperature conditions, although not shown to be as critical for flying qualities, should be given consideration.

(C) Additionally, design deficiencies surfaced when the rotorcraft were exposed to temperature extremes and some of these difficulties were severe enough to require the redesign of equipment and/or materials. Therefore, to satisfy $ 27.1309(a), the applicant needs to substantiate the total rotorcraft throughout the foreseeable range of operating temperatures.

(ii) Procedures.

(A) The FANAUTHORITY is responsible for verifying the effects of temperature on performance and handling characteristics. A limited flight verification, if necessary, could include spot checks of hover performance, IGE controllability, vibration, simulated power failure, static stability, height-velocity, VNE/VDevaluations, ground resonance, etc. In addition, systems should be evaluated to determine satisfactory operations.

(B) Extrapolation of test data should only be allowed if the applicant’s predicted or calculated data is verified by actual test, but in any case extreme caution should be used for extrapolations that are 10° C below or 20° C above those values tested.

AC 27-1A 7130197

(5) Enaine Power - Turboshaft Enaine.

(i) Background.

(A) Thepurpose ofrotorcrafi petiormance flight testing istoobtain accurate quantitative flight test performance data to provide flight manual information.

(B) Flight tests are designed to investigate the overall performance capabilities of the rotorcraft throughout its operating envelope. This testing furnishes information to be included in the flight manual and provides a means of validating the predicted performance of the rotorcraft with a minimum installed specification engine.

(C) The power used to complete the flight manual performance must be based on power values no greater than that available from the minimum uninstalled specification engine after it is corrected for installation losses. A minimum uninstalled specification engine is one that, on a test stand under conditions specified by the engine manufacturer, will produce the certificated power at specification temperatures and/or speeds. The specification values may be either a rating or m. Some engine manufacturers certify an engine to a specified power at a particular engine temperature or speed rating with higher allowable limits. The ~ is the maximum value the installed engine is allowed in order to develop the specification power. Prior to installation of each engine in a rotorcraft, the performance is measured by the engine manufacturer. This is done by making a static test run in a test cell and referring the results to standard day, sea level conditions. The performance parameters obtained are presented as uninstalled engine characteristics on a test log sheet. This is commonly referred to as a “final run sheet.” Figure 58-3 compares a typical engine to one the manufacturer has certified as a minimum uninstalled certified engine.

(D) After engine certification, the engine manufacturer is responsible to ascertain that each engine delivered will produce, as a minimum, the certified power without exceeding specification operating values; therefore, a “final run sheet” is created for every engine produced. Additionally, if needed, arrangements can usually be made with the engine manufacturer to obtain a torque system calibration for individual engines. This will further optimize the accuracy of the engines used in the flight test program. The engine manufacturer will also provide predicted uninstalled power available for the various power ratings. This information may be derived from an engine computer “card deck” and from charts and tables in the engine detail installation manual. These data also provide engine performance for the range of altitudes and temperatures approved for the engine and include methods for correcting this performance for installation effects. The parameters contained in a typical “card deck” are plotted for one engine rating in Figure 58-4.

(E) Several power losses may be associated with installing an . . engine in a rotorcraft. Typical losses are air inlet losses, gear losses, losses, and powered accessory losses such as electrical generators.

Par 58

air exhaust Additional flight

manual performance considerations are the torque indicating system accuracy and torque needle split. The predicted uninstalled power available engine characteristics cannot be assumed to be the actual power available after the engine is installed in the rotorcraft because this procedure would neglect the installation power losses. It is necessary to know the installation losses in order to determine the flight manual performance. Installation losses are reflected reductions in available power resulting from being installed in a rotorcraft. These losses usually consist of those incurred due to engine inlet and/or exhaust design. The rotorcraft manufacturer conducts tests to confirm the installed specification engine power available on which published performance is based. The specific methods used vary widely between manufacturers but usually include some combination of ground and flight tests. Figure 58-5 is a typical installed power available chart for one set of conditions.

(F) The installed power available is, in most cases, lower than obtained on a test stand. This is especially true at lower airspeeds where exhaust reingestion may occur and there are changes in airflow routing. The rotorcraft manufacturer may elect to determine the installation losses for different flight conditions to take any airspeed advantages. This is acceptable if, for example, the hover performance is based on the actual power available from an installed minimum specification engine @ a hove[. Likewise, it is permissible for the rotorcraft manufacturer to determine his climb performance based on the actual power available from an installed minimum specification engine at the published climb airspeed. This will allow the manufacturer to take advantage of, for example, increased inlet efficiency.

(ii) Procedures.

(A) The installed minimum specification engine power output has been predicted and calculated for various flight conditions. It is imperative that the predicted values be verified by actual flight test. The flight test involves obtaining engine performance measurements at various power settings, altitudes, and ambient temperatures. The data should be obtained at the actual flight condition for which the performance is to be presented (i.e., hover, climb, or cruise).

(B) Following a power increase, engine temperature and/or RPM can significantly decrease for a period of time as torque is held constant. Said another way, torque will increase if RPM and/or temperature are held constant. This is a characteristic typical of turbine engines due largely to expansion of turbine blades and reduced clearances in the engine. Some engines may show a temperature increase at constant power due to engine or temperature sensing system peculiarities. An engine will usually establish a stabilized relationship of power parameters in approximately 2 or 3 minutes. For this reason, the following procedure should be used when obtaining in-flight engine data.

(1) To determine the takeoff and 2 %-minute values, first stabilize the engine at a low power setting. After stabilization, rapidly increase the power

demand to takeoff and/or 2 %-minute power levels. Record the engine parameters as soon as the specification torque, temperature, or speed is attained. Care must be taken not to exceed a limit. These readings should be obtained approximately 15 seconds after power is initially applied.

(2) To determine the 30-minute and/or maximum continuous power values, approximately 2 to 3 minutes of stabilization time after power is increased is generally used, but up to 5 minutes stabilization time is allowed. The reason for the different procedures is when a pilot requires takeoff or 2 %-minute power values he is in a critical flight condition and does not have the luxury of waiting for the engine(s) to produce rated power. Stabilization time is allowed for the maximum continuous and 30-minute ratings because these values are not associated with flight conditions for which power is needed immediately.

(C) The in-flight measurements recorded with the engine(s) on the flight test rotorcraft must be corrected downward if the test engine is above minimum specification and corrected upward for a test engine that is below minimum specification. This correction is necessary to verify that a minimum specification engine installed on a production rotorcraft is capable of producing the power values used to compute the flight manual performance without exceeding any engine limit. In addition, if the production rotorcraft’s power measurement devices have significant (greater than 3 percent) power error, this error must be accounted for in a conservative manner.

(D) On multiengined rotorcraft, the engine location may result in different installation losses between engines. If this condition exists, multiengined performance should be based on the total power available after considering the different installation losses and with minimum specification engines installed. One-engine-inoperative performance must be based on the loss of the engine which has the lowest installation losses. Additionally, the power losses due to such items as accessory bleed air, particle separators, engine driven accessories, etc., must be accounted for accordingly.

(E) Power available data should be obtained throughout the test program at various ambient conditions. Some engines have devices which restrict the mechanical N~ speed to a constant corrected speed at cold temperatures. Others may limit power to a fuel flow value which would be encountered only at certain ambients. Others may limit by torque limiting devices. Therefore, power available data should be obtained at various ambients to verify that all limiting devices are functioning properly and have not been affected by the installation.

(F) Through use, turbine engine power capabilities decrease with time. This is called engine deterioration. Deterioration is largely a function of the particular engine design, the manner, and the environment in which the engine is operated. There is a need, therefore, to provide a method which can be used in service to periodically determine the level of engine deterioration. A power assurance curve is

usually provided to allow the flightcrew to know the power producing capabilities of any engine. A power assurance check is a check of the engine(s) which will determine that the engine(s) can produce the power required to achieve flight manual performance. This check does not have to be done at maximum engine power. Figure 58-6 is a typical power assurance curve for an installed engine showing minimum acceptable torque which assures that power is available to meet the rotorcraft flight manual performance. Some power assurance curves have maximum allowable N~ limits that must not be exceeded for a given torque value. An in-flight power assurance check may be used in addition to the pretakeoff check. The validation of either check must be done by the methodology used to determine the installed minimum specification engine power available. For the in-flight power assurance check there must be full accountability for increased efficiency due to such items as inlet ram recovery, absence of exhaust reingestion, etc. A power assurance check done statically and one conducted in-flight must yield the same torque margin(s). An engine may pass power assurance at low power but still may not be capable of producing the rated power values. This occurs when the curve of corrected power and corrected temperature for the engine intersects the minimum uninstalled specification engine curve. If this condition exists, the entire power assurance and power available information may need to be reestablished.

(6) Deteriorated Enaine Power - Turboshaft Engine.

(i) Background.

(A) A specific engine model may have been certificated for operation with power which has “normally” deteriorated below specification. This “normal” deterioration refers to a gradual loss in engine performance, possibly caused by compressor erosion, as opposed to a sudden performance loss which may be due to mechanical damage. The application for deteriorated engine power should not be confused with the installed mechanical engine derating which is frequently used to match transmission and engine power capabilities.

(B) The use of deteriorated power is intended to allow continued operations with an engine which is serviceable and structurally sound, although aircraft performance may be depreciated. The useful life of the engine may, therefore, be extended at a dollar savings to the operator.

(C) Although installed performance is the primary topic in this discussion, considerations must be given to other operational characteristics and systems which may be affected by deteriorated engine power. These include:

(1) Engine characteristics (~ 27.939). Surge margin, engine res~onse, and air-restart capability might be affected and should be addressed, but flight testing may not be required and fuel scheduling mechanism.

depending on the individual engine/aircraft installation

Par 58

(2) performance of customer bleed air systems maybe degraded slightly. No problem would be anticipated unless certain items within the system depend on a critical Pc for their function.

(3) The maximum a~ainable gas producer speed, and thus power available under certain ambients, may be affected if Pc is an input to the fuel scheduling mechanism.

(4) Systems for surge protection which schedule on Pc such as bleed valves, flow fences, bleed bands, and variable inlet guide vanes may be influenced. The effect would normally be negligible unless when installed, the installation losses, combined with reduced Pc because of deterioration, would cause the bleed device to open and reduce power at any one of the engine ratings.

(ii) Procedures.

(A) The need for flight tests to verify predicted power available with deteriorated engines depends on the scope of testing which occurred during initial certification. If the original rotorcraft certification included flight testing as described in Paragraph (5) (engine power-turboshaft engines) herein for validation of power available, the need for a demonstration with deteriorated engines is greatly diminished and perhaps eliminated.

(B) If flight testing to verify deteriorated engine power available is deemed necessary, the procedure used would be the same as that described in Paragraph (5) (engine power-turboshaft engines), except that the data would be corrected downward to a deteriorated engine runline. Efforts should concentrate on obtaining data in areas of the operational envelope where maximum gas producer speed is likely to be attained, or where bleed valves or other devices which schedule on gas producer discharge pressure are likely to function. On many installations maximum gas producer qpeed will occur with cold temperatures and high altitudes; bleed valves and other devices which schedule on gas producer discharge pressure are most likely to function and reduce power on a hot day at low altitude.

(C) The adjustments to the normal power assurance check procedures for deteriorated engines will be influenced by the preferences of the aircraft manufacturer and by any special stipulations of the engine certification established as a condition for the engine to remain in service when below specification. Possibly, more stringent and more complicated engine monitoring procedures will be introduced when allowing the use of deteriorated power; for example, an in-flight trend monitoring program with the associated bookkeeping duties may be required. Such an in-flight procedure must be evaluated by flight tests as described in Paragraph (5) (engine power-turboshaft engines) herein. Normally, however, the manufacturer would be expected to present a modification, or extension of the power assurance procedure

already in place for the specification engine, which could eliminate the need for flight test evaluation.

58A. ~ 27.45 (Amendment 27-21) GENERAL.

a. Exdan ation. Amendment 27-21 adds S 27.45(f) to the regulation. This section establishes the requirement for furnishing power assurance information for turbine powered rotorcraft. This information is to provide the pilot a means of determining, prior to takeoff, that each engine will produce the power necessary to achieve the performance presented in the rotorcraft flight manual (RFM).

b. Procedures. All of the policy material pertaining to this section remains in effect. In addition, the power assurance information included in the RFM should be verified. Although this requirement is normally met with a power assurance curve, other methods of compliance may be proposed.

58B. 627.45 (Amendment 27-29) GENERAL.

a. Explanation. Amendment 27-29 added the requirements for certification of 30-second/2-minute One Engine Inoperative (OEI) power ratings. For rotorcraft approved for the use of 30-second/2-minute OEI, partial power checks currently accomplished with approved power assurance procedures for lower power levels may not be sufficient to guarantee the ability to achieve the 30-second power level.

b. Proce dures. Information provided in Appendix 1 of this AC includes guidance material on power assurance procedures to assure that the OEI power level can be achieved.

CERTIFICATION BASIS

FAR 27 CAR 6 CAR 06

Par 58 Rqmts Ref. H-V Level 1. MGW Sea 2. Max. OGE 27-Amdt. 21 Level 2. Wt. selected 1. MGW Sea 27-Amdt. 2 Level 2. Wt. selected 1. MGW Sea Original 2. Wt. selected Level 1. MGW Sea 6-Amdt. 7 Level 2. Wt. selected 1. MGW Sea 6-Amdt. 4 2. Wt. selected Level 1. MGW Sea Original requirements. wt. and alt. 1. No specific Original 7/30/97

27.25 wt. Lesser of: by applicant at by applicant at by applicant by applicant by applicant at

27.1519 27.1587 27.79 Conditions Test b. 7000' Hd a. Max. alt. cap. lessor of: b. 7000' Hd a. Max. alt. cap. lessor of: b. 7000' Hd a. Max. alt. cap. b. 7000' Hd a. Max. alt. cap. at lessor of: Idg. alt. max. t.o. and max. t.o. and |Idg. alt.

6.116 6.741 6.743

3. H-V is perf. 3. H-V is perf. 3. H-V is perf. 3. H-V is perf. 3. H-V is perf. 3. H-V is H-V is Info. info. info. info. info. operating operating 4. Max. alt. For 4. If H-V wt is limitation. limitation. which H-V is less than IGE wt., RFM valid wt. becomes limitation for t.o.Adg.

AC 27-1 5. If H-V is less Para than OGE wt., 58 & 59 H-V wt. becomes limit. 6. Applicant is encouraged to demo H-V to Remarks WAT limits. 7. Hover data may be shown above 7000' if H-V & IGE are demo'd to 7000' AC 27-1A

FIGURE 58-1. H-V REQUIREMENTS

Rqmts

IGE CONTROL Ref. 27.25 27.143 27.1587 AC 27-1 Para 58 &81

Par 58

CERTIFICATION BASIS

FAR 27 CAR 06 27-Amdt. 21 Original Original Original 1. MGW Sea Level 2. Max. IGE wt. Lesser of: 2. Wt. selected by applicant to max. 1. MGW Sea Level 2. Max. approved wt. requirement. 1. MGW Sea Level for t.o.Adg at alt 1. No specific AC 27-1A

a. Max. alt. cap. t.o. and Idg. alt. above sea level. b. 7000' Hd 3. Critical CG 3. Critical CG Test 3. Critical CG 4. Critical Rotor 4. Critical Rotor RPM Conditions 4. Critical Rotor RPM 5. Wind not less than RPM 5. Critical wt. 20 mph. |5. Wind of not less 6. Wind of not less than 17 kts. than 20 mph

RFM 6. Max. safe wind is perf. info. 7. Max. safe wind is perf. info. 6. Max. safe wind is perf. info.

7. If 17 kts. wind demo'd to alt. less Remarks than 7000', a corresponding WAT limit must be established.

7/30/97

FIGURE 58-2. IGE CONTROLLABILITY REQUIREMENTS

AC 27-1A

MIN CERTIFIED SPECIFICATION ENGINE

FIGURE 58-3.

1000 1100 1200 1300 1400 1500

CORRECTED TOT “F

SHAFT HORSEPOWER VS TURBINE OUTLET TEMPERATURE -

SEA LEVEL STANDARD DAY

200 300 400 500

SHAFT HORSEPOWER AVAILABLE

FIGURE 58-4. UNINSTALLED TAKEOFF POWER AVAILABLE

-–l––

I

I

I

-IL -

I

I

I

11] I

I

I I

I 11,, I I

—

—

I I Ill

---. -\-\!-\-\~\:\!-\:’

II — — LL_ll_l J_lJ_L\-_L_ll_A_l _

__l__l__ r-*-+, --~-]~-t, -tli i i\i\i\\i\i\i i i

Ill Ill I II

\

m\\\:-~-

11[

Ill

Ill !\\:\ \i\!\ “ __l__~__ }__;__, _ _,_ I_ ‘____ ;– I

I II II 1[

I

I

I

1’

I

I

I I I Nh

Ill II 1111 Ill II 1111 Ill .J__l__L_d-–l - S l––p– 1– [– ® -l–

Ill II Ill II II II

II 1111 Ill II 1111 Ill

200 300 400

SHAFT HORSEPOWER AVAILABLE

b .l.–. ––p–__/– II I II I 1[ I I –L––l- 1– 1 I II I

–+––l–

. L

I

I

FIGURE 58-5. INSTALLED TAKEOFF POWER AVAILABLE, ANTI-ICE OFF, 400 RPM

(ii z o ~ nz o c)

II

o“ o

n

I I 1 1 1 /1/1

A- V

I /i’/t’/l’’/v/-Y. /1 A 1 1 1 1 1 I I

n

o N

o

76 Par58

59. ~ 27.51 TAKEOFF.

a. Explanation. Section 27.51 details the conditions under which takeoff data must be obtained. The flight manual must contain the technique(s) to be used to obtain the published flight manual takeoff procedures. Technique should not be confused with exceptional pilot skill and/or alertness as mentioned in ~ 27.51. Because rotorcraft differ, different pilot techniques are sometimes required to achieve the safest and most optimum takeoff performance. The recommended technique that is published in the flight manual must be determined to be one that the operational pilot can duplicate using the minimum amount of type design cockpit instrumentation and the minimum crew. Only rotorcraft takeoff techniques will be covered in this section.

b. Background.

(1) Certain special takeoff techniques are necessary when a rotorcraft is unable to take off vertically because of altitude, weight, power effects, or operational limitations. The recommended technique used to take off under such conditions is to accelerate the rotorcraft in-ground-effect (lGE) to a predetermined airspeed prior to climbout. Takeoff tests are performed to determine the best repeatable technique(s) for a particular rotorcraft over the range of weight and altitude for which certification is requested.

(2) Utilizing the total power available to execute a takeoff may not be operationally feasible due to such items as HV or aircraft attitude constraints. In such situations, hover power required plus some power increment may be the maximum recommended for use.

(3) Wheel or skid height should be not less than that demonstrated satisfactorily for the high speed, low altitude portion of the HV curve, or that height below which ground contact may occur when accomplishing takeoff procedures.

(4) For rotorcraft fitted with wheels, a running takeoff procedure maybe accepted.

c. Procedu res.

(1) There are different takeoff profiles which may be used to complete a maximum performance takeoff in a rotorcraft. The manufacturer will normally determine which method is best for a particular rotorcraft. The most commonly accepted method is the hover and level acceleration technique. In this technique, the rotorcraft is stabilized in a hover at the reference height. From the stabilized hover, the rotorcraft is accelerated to the climbout airspeed using the predetermined takeoff power. When the desired climbout airspeed is achieved, the rotorcraft is rotated and the climbout is accomplished at the scheduled airspeed(s) and constant rotor RPM. Power adjustments may be accomplished to maintain the targeted power except where

AC 27-1A 7130197

procedure requires high workload outside the cockpit (i.e., that portion of takeoff where horizontal acceleration close to the ground has pilot scan outside the cockpit and adjustment of engine torque or temperature would require an undue increase in workload). The recommended takeoff procedure must be demonstrated to remain clear of the HV “avoid” areas without requiring exceptional piloting skill or exceptionally favorable conditions.

(2) The hover reference height is established as the minimum skid or wheel height above the takeoff surface from which a takeoff can consistently be accomplished in zero wind without contacting the runway surface. The takeoff must be accomplished with power fixed at the power required to hover at the hover reference height and must not require exceptional piloting skill to avoid runway surface contact.

7/30/97

60.-62. RESERVED.

Par60

AC 27-1A

Intentionally

Left Blank

79(thru 81)

63. ~ 27.65 (Amendment 27-14) CLIMB: ALL ENGINES OPERATING.

a. Exdanat ion.

(1) Rotorcraft other than helicopters.

(i) Section 27.65 requires that the steady rate of climb be determined for each rotorcraft other than helicopter with maximum continuous power on each engine for the range of weights, altitudes, and temperatures for which certification is requested. Equivalent levels of safety have been found wherein the applicant was allowed to select a climb airspeed that was not the actual Vy. The selected airspeed must be consistent with the speed used to show compliance with such items as cooling, stability, etc. The rate of climb resulting from the selected climb airspeed versus that from the actual Vy shall not differ to an extent that a pilot will be encouraged, by appreciable increases in climb performance, to fly a climb airspeed different from that published in the flight manual.

(ii) For rotorcraft other than helicopters, the climb performance data obtained above must be used to show that a minimum climb gradient can be achieved for each weight, altitude, and temperature within the range for which certification is required. This gradient must be at least 1:10 if testing is done to determine the required takeoff distance over a 50-foot obstacle. If this option is selected, an explanation of the takeoff distance determination requirements and procedures may be found in Paragraph 62 of AC 29-2.

(iii) If takeoff distance is not determined, the minimum climb gradient must be 1:6 for standard sea level conditions.

(2) For helicopters, Vy must be determined for standard sea level conditions at maximum weight using maximum continuous power on each engine. Although not required, the steady rate of climb may be determined using the procedure in Paragraph 63c.

(3) For helicopters, if V~~ at any altitude is less than the maximum gross weight sea level standard day condition Vy, the steady rate of climb must be determined at the climb speed(s) selected by the applicant not to exceed VNE. The climb performance must be determined from 2,000 feet below the altitude from where VNE intersects Vy up to the maximum altitude for which certification is requested. This should be done utilizing maximum continuous power on each engine with the landing gear retracted.

b. Procedure to Determine VY.

(1) Sawtooth climbs may be used to determine Vy. If such a technique is used, climbs should be flown in pairs on opposite headings 90° to the wind at the test altitude. This procedure will minimize any windshear effects. All testing must be done in smooth

82 Par63

Continue reading ↓ 120 of 1550 passages shown