Radar Vectors
Advisory Circular Cancelled Issued Jul 1, 1970 AAS-200 83 pages Copy saved Nov 18, 2026

AC 150/5320-5B Airport Drainage

Provides guidance for engineers, airport managers, and the public in the design and maintenance of airport drainage systems.

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

AC NO: 150/5320-5B DA TE: 111110 ADVISORY CIRCULAR

AC NO: 150/5320-5B DA TE: 111110 ADVISORY CIRCULAR

DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION

SUBJECT: AIRPORT DRAINAGE

1. PURPOSE. This circular prO\·ides gnidnnce for engineers, airport managers, and the public in the design and maintenance of airport drainage systems.

SUBJECT: AIRPORT DRAINAGE

2. CANCELLATION. This publication cancels "Airport Drainage," AC l50/53:20-5A, dated 1965.

3. REFERENCES. The publications listed in the Bibliography, page 79, prO\·ide further guidance and technical information as may be required.

4. EXPLANATION OF REVISIONS. In addition to minor changes in the text and figures, this adYisory circular includes:

a. Reference to more detailed rainfall frequency charts now being published by the ,v eather Bureau for eleYen "' estern States.

b. Addition of other fundamentals for use of W'eather Bureau Technical Paper Ko. 40 and other technical papers and charts.

c. Emphasis on designing for direct runoff. d. Information on grates and frames yersns aircraft types, weights, and tire pressures.

e. A new section on flow in open channels. f. Consideration of low head situations for grates in aprons.

g. A new section on cuh-erts. h. New recommendations for loads on structures in Yiew of rnry heayy aircraft.

i. Additional emphasis on erosion control. j. Information on permeabilit.r factoi·s · in subsurface drainage.

· k. Addition of information on use of plastic filter cloths in subsurface drainage.

1. Some corrections to sample drainage system design data and to computations for ponding examples.

m. Re,·ision of minimum pipe coyer table including addition of corrugated aluminum alloy pipe.

n. Mention of need for pollution control. o. Addition of a bibliography of reference material.

•

•

•

I

AC 150/5320-58

• CONTENTS Paragraph Page

Chapter 1. INTRODUCTION

Chapter 1. INTRODUCTION

1. Characteristics of Airport Drainage --------------------------------------- 1

2. Purpose of Airport Drainage --------------------------------------------- 1

Chapter 2. HYDROLOGY

3. Rainfall------------------------------------------------------------------ 3 Figures 1 through 5 Rainfall Frequenc~· liaps --------------------------- 6 Figure 6 Intensltr Cur,es for Storms in ''lcinlty of Example Site … 8

Chapter 3. COMPUTATION, COLLECTION, AND DISPOSITION OF RUNOFF

Chapter 3. COMPUTATION, COLLECTION, AND DISPOSITION OF RUNOFF

4. Runoff-------------------------------------------------------------------

5. Runoff Coefficient … ------------------------------------ … Table I ,·alue of Factor "C" -------------------------------------------

6. Time of Concentration---------------------------------------------------- Figure 7 Surface Flow Time Curves -------------------------------------

4. Runoff-------------------------------------------------------------------

7. Collection and Disposal of Runoff ----------------------------------------- Figure 8 Suggested Grading for Small Ponding Areas on Continuous Line

of Inlets-------------------------------------------------------------

8. Flon· in Conduits -------------- ------------------------------------------ Table II Coefficient of Roughness --------------------------------------- Figure 9 Xomograph for Computing Required Size of Circular Drain for

n 0.012 or 0.013 ------------------------------------------------------ Figure 10 Xomograph for Computing Required Size of Circular Drain for

n 0.021 or 0.024 ------------------------------------------------------ Figure 11 Nomograph for Computing Required Size of Circular Drain for

n 0.023 or 0.027 ------------------------------------------------------ Figure 12 Nomograph for Computing Required Size of Circular Drain for

n 0.031 --------------------------------------------------------------- 9. Flo"· in Open Channels -------------------------------------------------- Figure 13 Solution of the llanning 1-'ormula -----------------------------

Figure 14 Dimensions of Trapezoidal Channels with 21h to 1 Side Slopes --- Figure 15 Dimensions of Trapezoidal Channels with 3 to 1 Side Slopes ___ _

Figure 16 Dimensions of Trapezoidal Channels with 4 to 1 Side Slopes ___ _ Figure 17 Dimensions of Triangular Channels --------------------------- Figure 18 Dimensions of Parabolic Channels ----------------------------- Figure 19 Solution for Dimensions of Parabolic Channels -----------------

Figure 20 Retardance Coefficients for Flow in Turfed Channels ------------

10. Structures---------------------------------------------------------------- Figure 21 Examples of Typical Inlet Grates ----------------------------- Figure 22 Examples of Inlet Design ------------------------------------

Figure 23 Suggested Types of Headwalls -------------------------------- Figure 24 Suggested lllanhole Design ------------------------------------ Figure 25 Determination of Typical Inlet Grating Discharge Cur,e …

11. Cul,erts -----------------------------------------------------------------

11. Cul,erts -----------------------------------------------------------------

9

10 10

10 11

12

13

14 16

17

18

19

20

21 22 23 24 25 26

28 29

30 31 32 33 34 35

37

I•

Page I

Page Ii AC 150/5320-SB

Paragraph Page

Chapter 4. GRADING CRITERIA

12. Selecti,e Grading --------------------------------------------------------- ;m 13. Soil Conditions ---------------------------------------------------------- 39 Figure 2G Example of Widened Subbase Sections for Extreme Snow Con-

Chapter 4. GRADING CRITERIA

ditions--------------------------------------------------------------- 40 14. Loads on Conduits ------------------------------------------------------- 41 Table III Minimum Depth of Co,er in Feet for Pipe Under Flexible and

Rigid Pa,ement ------------------------------------------------------ 42 Figure 27 Trenc-h and Projecting Conduits ------------------------------ 45 15. Loads on Structures------------------------------------------------------ 47

IG. Erosion Control ---------------------------------------------------------- 48 Figure 28 Types of Surface and Interceptor Ditches ---------------------- 50 Figure 29 Typical Embankment Protection Structures ------------------- 51

Chapter 5. THE DRAINAGE SYSTEM

Chapter 5. THE DRAINAGE SYSTEM

17. Basic Information Required ---------------------------------------------- 53 18. Drainage Layout--------------------------------------------------------- 54 Figure 30 Topographic- )lap--------------------------------------------- 55 Figure 31 Runwa~- Safety Area and Runway Drainage ------------------ 56 Figure 32 Plan and Profilt> of Drainage Pipe ---------------------------- 57 19. Surface Drainage--------------------------------------------------------- 58 Figure 33 Portion of Airport Showing Drainage Design ------------------ 6(l Table IY Design Data for Drainage Example in Table Y ----------------- 61 Table Y Drainagt> Sy!'.'tem Design Data ---------------------------------- 62 20. Ponding------------------------------------------------------------------ 63 Figure 34 Exampl(' of Pro,iding for Ponding Area ---------------------- 64 Table YI Computations for Ponding Example in Figures 34 and 35 … 65 Figure 35 Cumulati\·e Runoff for Ponding ------------------------------- 66

21. Subsurface Drainage ----------------------------------------------------- 67 Figure 36 Types of Subsurfac-e Drainage -------------------------------- 71 Figure 37 T)·pical Section of Subsurface Drains -------------------------- 72 Figure 38 Gradation of Backfill for Subsurface Drain … 73 Figure 39 Gradation for Filter Material --------------------------------- 74 Figure 40 Template and Trenc-h Width for Pen-ious Backfill -------------- 75

22. Construction ------------------------------------------------------------- 76 Figure 41 l\Iethods of Laying Drainage Pipe ----------------------------- 77 23. Pollution Control ------------------------------------------------------- 76 24. )laintenance of the S~·stem ----------------------------------------------- 76 Bibliography----------------------------------------------------------------- 79

AC 150/5320-58

Chapter 1.

1. CHARACTERISTICS OF AIRPORT DRAINAGE.

a. An airport should have smooth, welldrained operational areas with sufficient stability to permit the safe mO\·ement of aircraft under all weather conditions. The design of adequate drainage is important because it affects the stability and usability of extensive areas: yet, these areas are subject to varying

soil and drainage conditions, and also have relati,·el~· flat grades.

b. The drainage system should be built before or during the grading operations because draining and grading are interrelated. A drainage system cannot be expected to function properly unless the airport area has been correctly graded to di.-ert the surface runoff into the system. In the absence of adequate stabilization or pavement, drainage does not assure an all-weather airport, but it does shorten the interrnl of nonuse.

c. The large area that must be drained on an average airport requires an economically designed drainage system to realize the full rnlne of the im·estment made. Sound engineerinp: principles must be applied in the utilization of all a rnilable data, such as: topo· graphic maps: soil reports; determinations of water tables: intensity, frequency, and duration of precipitation: climate and temperature reports: and nature of the area surrounding the particular site.

d. The topography of the site and the offsite areas affect the final layout of the runways, taxi"·ays, aprons, and buildings. The location and size of these facilities will control the grading and the extent of drainage required. It is important that the grading of the air-

port be such that all shoulders and slopes drain away from runways, taxiways, and all parnd areas. After final elerntions on the airport ham been determined, all surface flow of water onto the site must be intercepted and disposed

Chap 1

Page I

INTRODUCTION

of, any depressed or low spots on the site must be drained, and all surface runoff must be accumulated and directed into adequate outfalls.

e. Enough tests should be taken to identify all soil types because texture, permeability, and capillarity have a pronounced effect upon their drainability. Because of its effect on the stability of soils and on the ultimate design of the airport, the water table should be accurately determined o.-er the entire area. ,vhen a high water table does exist, provision should be made for controlling or lowering it-or alternatirnly raising the pavement grades-see paragraph 21.

f. In designing a drainage system, it is important to determine expected precipitation at the airport site. Intensity-frequency or precipitation data may be obtained and developed

from information in several publications as noted in paragraph 3.

g. Localized climatological data should be studied and ad rice sought on average frost penetration and recommended minimum depth of storm sewer installations for the area. For some localities, records of a.-erage accumulated snowfall would be pertinent to the drainage

design.

2. PURPOSE OF AIRPORT DRAINAGE.

a. The purpose of airport drainage is to dispose of water which may hinder any actiYity necessary to the safe and efficient operation of the airport. The drainage system should collect and remO\·e surface water runoff from each area, remove excess underground water, lower the water table, and protect all slopes from erosion.

b. Natural drainage normally does not meet these requirements. Constructed drainage facilities must be sufficient to prO\·ide for present

Par 1

Page 2

requirements and any future enlargements of the system. This may mean the installation of a portion of a drainage system to supple-

ment the natural drainage on the site or it may call :for a complete system to drain the entire airport area. A proper understanding of all contributing drainage factors determines the extent of the facilities required on each par-

ticular airport.

c. An inadequate drainage system can cause

Par 2

AC 150/5320-58

serious hazards to air traffic at airports. The most dangerous consequences of inadequate drainage systems are saturation of the sub-

grade and subbase, damage to slopes by erosion, loss of load-bearing capacity of the paved surfaces, and excessive ponding of water.

d. Aprons and other paYement should be sloped away from buildings so that there will be no possibility of fuel spillage flowing toward buildings.

Chap 1

AC 150/5320-SB

Chapter 2.

3. RAINFALL.

a. The determination of the amounts of rainfall and runoff to be used as a basis for design of a drainage system is the primary step to be considered by the designer. The rate of storm runoff which will flow into the system must be established in the preliminary design stage. At some locations this may in- Yoh·e rainfall plus melting sno.Y or ice.

b. The importance of the rainfall-intensity factor is well known to drainage engineers, pa;- ticularly in its relationship to total runoff. Innstigations haYe shown that results of studies regarding the probable intensity, frequency, and duration of rainfall in particula1· locations are more likely to be correct and consern:i.tiYe if they are obtained from the records of many stations rather than from the record of one station. Single stations seldom giYe a true picture of the rainfall-frequency regime for rnr ious locations. The use of many stations in a region to determine the pattern and rn lue of the rainfall-frequency Yalues tends to minimize the limitations of a small sample in both time and space.

c. l\Iany inrnstigations and studies haw been conducted to find a basis for making reasonable estimates of the intensities, frequencies, and durations of rainfall for different loca-

tions. A pre,·iously used publication by D. L.

Yarnell, "Rainfall Intensity-Frequency Datat has now been replaced by more recent studies. Rainfall-frequency data :for the rnited States, Puerto Rico, the Virgin Islands, Hawaii, and Alaska can be obtained from a series of ,veather Bureau Technical Papers. Data for the conterminous United States are giYen in

ESSA-,Yeather Bureau Technical Paper Ko. 40, "Rainfall Frequency Atlas of the United States," dated ~lay 1961. Technical Paper Ko. -10 is intended as a cmwenient summary of

empirical relationships, "·orking guides, and

Chop 2

Page 3

HYDROLOGY

maps, useful in practical problems reqmrmg

rainfall-frequency data. It is an outgrowth of seYeral previous "reather Bureau publications on this subject and contains an expression and generalization of the ideas and results in earlier papers. It is di rided into two parts:

(1) The first part presents the rainfall analyses. Included are measures of the quality of the rnrious relationships, comparisons w·ith

preyious works of a similar nature, numerical examples, discussions of the limitations of the

results, transformation from point to areal frequency, and seasonal rariation.

121 The second part presents 49 rainfallfrequency maps based on a comprehensfre and integrated collection of up-to-date statistics, sernral related maps, and seasonal rnriation diagrams. The rainfall-frequency (isoplm·ial) maps are for selected durations from 30 minutes to 24 hours and return periods from .1 ~o 100 years.

Rainfall-frequency data for Puerto Rico and the Virgin Islands, Hawaii and Alaska can be obtained from ESSA-,Yeather Bureau Technical Papers No. 42, "Probable ~laximum Precipitation and Rainfall-Frequency Data for Puerto Rico and the Virgin Islands, "dated 1961; Ko. 43, "Rainfall-Frequency Atlas of the Hawaiian Islands," dated 1962: and Ko. 47, "Probable Maximum Precipitation and Rainfall-Frequency Data :for Alaska," dated 1962, respectiYely.

d. The preferred source of precipitation-frequency information :for the eastern two-thirds of the conterminous United States is ESSA- ,veather Bureau Technical Paper Ko. 40.

Rainfall-frequency data for the ele,·en ,vestern States can be obtained from the physiographically adjusted precipitation-frequency maps currently being prepared by the ESSA· ,Yeather Bureau. These maps haYe been com-

pleted for the States of Arizona, Xe"· )fexico,

Par 3

Page 4

Colorado, Utah, ,vyoming, )Iontana, Idaho, ,vashington, and Oregon. Maps for Kernda and California are currently being prepared

and should be aYailable shortly. The maps for the ·western United States are only for the 6and 24-hour duration Yalues and relations giYen

in Technical Paper Ko. 40 must be used to obtain the Yalues for the shorter durations (see paragraph g below). Rainfall-frequency values for Puerto Rico and the Yirgin Islands, Hawaii and Alaska can be obtained from ESSA- ,veather Bureau Technical Papers Xos. 42, 43, and 47, respectirnly. It should be recognized that there may be. some locations where the

ya]ues from the generalized charts may be either an ornr or an underestimate. If the engineer suspects this to be the case, he should inrnstigate all possible sources of data for additional information to rnrify or rerise the published Yalues. Possible data sources are the local ESSA-"'eat her Bureau Office, the

State Highway Office, State Hydrographers Office, City Engineer·s Office, and perlwps local drainage districts or utility companies. Such locally derh·ed data should not be used to ornrride the data from the '\Veather Bureau Technical Papers unless there is ample e,·idence that the latter data is clearly not applicable to the local situation.

e. The rainfall intensity-duration cunes required for design purposes, in the conterminous United States, can be deriYed from the charts in Technical Paper Ko. 40. Figures 1 to r, are examples of the charts in that paper. It is not intended that these figures be used for determining intensity as the scale was kept quite small for illustration purposes. Return periods of 2, 5, and 10 years are sufficient for airport drainage calculations and sufficient for com-

parisons between such periods. To construct intensity-duration cun-es such as shown in Figure 6, begin by spotting the airport location on the 30-minute, I-hour, and 2-hour charts

for 2, 5, and 10 years in Technical Paper No. 40. Then read the intensities by scaling between the isolines, linear interpolation between adjoining isolines is sufficient. For example, the 5-year, 30-minute rainfall chart (Chart 3) reYeals that the intensity at Chicago would be 1.37 inches. This must br conwrted to a 1-

Par 3

AC 150/5320-58

hour basis for currn plotting purposes, therefore, the scaled quantity must be multiplied by the ratio between 1-hour and the %-hour duration (1.37 X (60 + 30) =2.74"). Plot this intel.lsity on coordinate paper (using inches per hour as ordinates and duration in minutes as abscissas). Similarly, scale the intensity for Chicago for a 1-hour rainfall to be expected once in 5 years from Chart 10, for a 2-hour rainfall from Chart 17, and convert the latter value to a 1-hour basis. As Technical

Paper No. 40 does not have short-duration rainfall charts, i.e., for 5, 10, and 15 minutes, it is necessary to use the ,veather Bureau dHeloped relations~1ip between a 30-minute rainfall on the one hand and 5-, 10-, and 15-minute amounts on the other. This relationship is as follows:

Duration (minutes) 5 10 15 Ratio 0.37 0.57 0.72

Thus, the Chicago 30-minute amount of 1.37 can be reduced to a 5-minute amount by multiplying 1.37 by 0.37 or 1.37 X 0.37 = 0.51"; similarly, 1.37 X 0.57 = 0.78" for the IO-minute amount, and 1.37 X 0.72 = 0.99" for the 15-minute amount. Then convert these Yalues to a 1-hour basis as described aboYe. Accordingly, the 5-, 10-, 15-, and 30-minute, I-hour, and 2-hour intensities giYe 6 points on the coordinate paper and a smooth cune can be drawn through the points to construct the 5-year cun-e. This curYe will indicate the intensity of rainfall to be expected for any time interrnl from 5 minutes to 2 hours for a storm that might occur once in 5 years. The same procedure should be followed to construct curYes for 2 and 10 years. Figure 6 is a graph exemplifying this procedure.

f. Similar proeedures can be followed in Puerto Rico and the Virgin Islands, Hawaii, and Alaska, using charts from the appropriate "·eather Bureau Technical Papers to obtain

Yalues for 30 minutes, 1, and 2 hours. The 5-, 10-, and 15-minute values can be approximated using the ratios with 30-minute rain-

fall values cited earlier.

g. The more detailed rainfall-frequency charts for the 11 ,vestern States, referred to in

paragrnph d abm·e, should be used to obtain

Chap 2

AC 150/5320-58

the rainfall intensities for the more rnriable conditions found in the mountainous areas of

,vestern United States. These studies provide detailed maps which depict the rnriation in rainfall-frequency mines in this portion of the country. These maps were dewloped to depict the rainfall-frequency rnlues for a,·erage conditions along orographic barriers and in mountain valleys. At some locations, where the topography departs significantly from arerage conditions, ralues determined from the generalized chart may be either an under or overestimate. Locally a,·ailable data for these locations could be considered by the engineer to modify rnlues obtained from the

generalized charts. Such locally derived data should not be used, howe,·er, unless there is ample evidence to show that the local situation insists that such data are more applicable than that in the generalized charts. The following procedure will need to be used to convert the information in the charts :for the 11 "'estern States to a more useable form. As the charts prm·ide rnlues for only the 6- and 24-hour

Chap 2

Page 5

durations, it is necessary to compute ralues for the shorter durations for our purposes.

This can b edone by using Figure 2 of Technical Paper No. 40. (First note, however, that these charts show values in tenths of an inch, so they must be converted to inches.) For example, read the 5-year, 6and 24-hour amounts for the airport location from the charts and plot these amounts on Figure 2.

Lay a straight-edge across the two points and read the values for 1- and 2-hour durations at the proper intersections. Estimate the 30-minute rainfall by multiplying the onehour value by 0.79. Then proceed to com·ert the 30-minute rnlue to 5-, 10-, and 15-minute

values by using the ratios given in paragraph e abm·e. Then convert the values to a I-hour intensity and construct a 5-year cune in the manner described in paragraph e.

h. The use of the data, de,·eloped as described in either paragraph e or g above, is

taken up later in Chapter 5 and is the basis for estimating runoff.

Par 3

.,, a ~ ..,

9 a ,, ...

- I , 4 I • ' r;

•)4 4 6 8 I L'1~,\ ,,,, f,rl 6., rr1<c1t . ,- ~ 12(," -. .::,-

9

~! .• ( \,l-.'\,12 6 ·~ 1 , 14" · " r,, , 7'14 ( ,, ',., .. , , ,'- I . . . I • , ' • 8 , · \', ,''., ''-16 "{\ ~8 ? ,' , ?';'I~ I . i 1""'',~' e. j{(,.,, 1 , 1. , \{

1 , ,L'( ')\

1 s ~'t 6 · .' 1 '· f-' ,', I, ~·2 ~ 1i ) ( J • / I ; I \ , ( r' r·: /·) I '1 · 18 ·' >r" 11 M_:'· , \ ,8; I _. · . ·r -~ _J,) , 2 2

8 I 4 '~ ' j -~ - 2 4 - 2 6 - I ...-·, 2 6 ' · I 2 I 4 I f ,, , 2 4 2 2 . 2 2 ~. 2 4 12 2 , rs. 141618' 22 tdonce1n5yeo . to bf! e,:pec e . fol I in inches. - te rain ,

1 Thirty -minu F

1 Thirty -minu F

1 gure

I j I 15 f'J1/ / .'

I 5 ;7ir--J., \ (

15 I 5/ (' 1( t \~

15 , '1~ ~ • ~

, '\

5 I • / 15 . /)•· 2 " I 5 15

15 1.r5 • , ·SI.., 7·~ ':\. . . ".i 15 l /) 2/·,1(?·(-,v- .,r,1<2

. ) \l '{.~ . ';) 4+'{ C;' \ .,/ , . i /r,. \ , / )_, ¥'. ii \ 2 5 ' 2\ ,)...- j t· ,.;·.

15 I 5/ (' 1( t \~

. ~ . . \ ',-fit. .

_.. 4 )~ 1(~ ~

1'5

) 5 15 Two·hour ,oinfoU, in inches, to be elpected Ol'\Ce m 5 yea,,

Figure 3

6 6 8 8 … ,rrf. 6 ('I' , ; . '\' . _8 \ I 2 e.,. 6 1•\ r' , .s, I"' 12[\ ,,,\JM,' J ( i 14 t ~JC, ~. " /; /• / ,\ I,\ [ I \ _,'.-'< 's·--,, 1~·, /',(12 >)\, ( I 2 , , ) 1 ! I 6 , I B1 • "I \ I 4 8 'l\ \~! r""· / I ' ) .. 1 i .,J 2 \ . ~ 1-Jp . ·-~·i'e1 6 1 _ Ii \l,'i\ B l ' j ,J / .·' / \ / ; ,~ ~ .•.,.. "'_ t) 2

I · · • /i,•. '· 1 I( ' '•' r' , '' 24 6 ,_..., '. 1 · . ' . . . , , ,1" • . I a , I '. I '.!-r r ' ( i , . ~4 . , ; ; ~.,-: j' ? ~

, 2 . .-~ ~i ) l I L 6 ¥i~ I -r-; :z_ 11 2 6 8 ; 6 j~ < 1 ,(I , f >~ -. . -\ ~ )( •

14 16 ~ • '/ -~ ' ff;;..,..,,_ ·~ 24

2 18 "".'.:.,- ' ) 1 54... J) l 12 24~6•',/218 28·~ ·JJe One-hour ro,rifall, ,n inches, to be expected once 1n 5 years

Figure 2

NOTES

TH£ WEATHER BUREAU O(V[LOPED RELATIONSHIPS FOR SHORT DURATIOtl RAINFALLS THE AVERAGE RELATIONSHIP 8[TW(EN

30 MINUTE RAINFALL ON T/if CJ,£ HANO AMJ 5-, 10-,ANO 15- MIMJTE RAINFALL ON THE OTHER CAN 8[ OBTAINED FROM TH[ FOLL OWING

DURATION (MIN) 5 10 15

DURATION (MIN) 5 10 15

RATIO 0)7 0 57 0 72

THUS A GEOGRAPHICAL POINT ON FIGURE I WHICH INOICATES A THIRTY MINUTE RAINFALL or I 6 INCHES ONCE IN 5 YEARS MAY BE REDUCED TO 5 MIIIUTES BY MUlTl!'LYlflG 1.6 BY 0)7,.592 INCHES OR 10 MINUTES AS 16 8Y 057•912 INCHES OR TO 15 MINUTES AS I 6 XO 72 • 1152 INCHES

• • •

If ACTUAL WEATHER BUREAU Rl:COROS OR SUPPLEMENTAL RECORDS ARE NOT AVAILABLE FOR THE POINT IN QUESTION

THEN THE CHARTS IN THE TECHNICAL f',tPER NUMBER 4 0 'RAINFALL FREQUENCY ATLAS or THE UNITED STATES' MAY BE USEO TO CONSTRUCT INTENSITY CURVES SUCH AS SHOWN IN FIGURE 6 INDEED FIGURES 1,2,l,4, 5 WERE CONSTRUCTED FROY TECHNICAL PAPER NUll8[R 40 ANO SERVE TO ILLUSTRATE TH[ METHOD or DEVELOPING AN INTENSITY· DURATION Cl/RV[ OR CURVES FIRST SPOT THE AIRPORT LOCATION UN()(R CONSl()(RATION ON rtGUR[ I 130 MINUTE RAINFALL,INCHES, TO BE EXPECTED ONCE IN 5 YEARS.I LOCATING TH[ POINT AS ACCURATELY AS

F1G1rnF.s 1, 21 a. Ilainfall frequency maps.

POSS111LE THEN SCALE THE INTUISITY FOR THE POINT IN QUESTION BY INTERPOLATION BETWEEN THE TWO ISOtiYETAL LIN(S ON EITHER SIDE Of THE POINT TO ILLUSTRATE, THE INTENSITY SCALED FROM FIGlAE I IS FCUID TO BE I 36 INCHES AT CHICAGO, THIS IS FOR A JO IIINUTE RAINFALL

TO et EXP£CT[O ONCE IN 5 YEARS THIS INTENSITY NEEDS TO 8( CONVERTED TO A I· HOU!! BASIS FOfl PL OTTING PUR , POSl'S

THUS THE SCALED QUANTITY Of 1 16 INCH[ S MUST BE IIIJLTIPLIED BY 60• JO OR 2 R£SULTING IN 1J6°X 2 •272' PLOT THIS INTENSITY ON COOROINA7E PAP[R ( USING

IMGH(S P(R HOIJR AS QROINATES A~ TIMES IN IMMUT[S AS AIISCISSAS ). SIMILARLY SCALE THE INTENSITY FOR CH1GAGO FOIi /. HOUR RAINFALL TO BE EXPECTEO ONCE IN 5 YEARS fROlol FIGURE 2 ANO FOLLOW TIil: ABOVE PllOGEDURE, TH(N US( FIGURE l fOfl TWO HOUR RAIN, FALL

ALSO, CONVERT THE JO MINUTE INTENSITY TO 5-,IO-, ANO 15 MINUTE INTENSITIES AS INDICATED ABOVE, CONVERT

TO I HOUR BAS IS ANO Pl.OT. FIGURE 6 ILLUSTRATES 2 5 ANO 10 YEAR flTENSITY DURATION CURVES CONSTRUCTED IN THIS IIANNER

•

• •

.,, a (Q ..

°'

> n - u, 0 … u, ... ~ ? u,

UI

·--

t"I :r Q .,,

' "' I

1 .. w

4 6 •.• ,- 6 6~- .' •. 6 _ 8_ , a ~, 6;;.j'~YI~. .T I \~--,.1 \.. ( -' 8 8/J \~. \\ \ · .-\ 12("·.,,__1,:,'·-;,- .j"1 t'!..,' • / ) \14' I ~.J.f.i \,, 12 e .a(/ I -0 \,1.,;.·x' ">,...14

8 ~ -•. J' 6 ;\ ''1 ) I ) 1' \ -· Y, ~ I 16 6 i(' . J ! - !)'. _,, . • ,. 2 8""·- (,'·, , 1 t ,' • I

6 6 ' /I~ \ -- . 2 \ . 6 I I. &,· . L . I 6 \ 2 2 -· '1:r'f..,e, , It' 22 I I 2 1 4· 1': 2 4 2.6 ' ' ., 2 6 I 6 · 2 ' 2. 8 2 2 ' 2 2'' 24 · • I 8 2 2 ona~hour roinfotl, ,,., inche, 1 to be e-..p,ected ()nee '" 2 years

Figure 4

.86 .{,1~ .6,6 8 t I 2 " I 4 •. ' ,i\• · J -1&-,-aJ!_E·, ~-,, , I ,18 .~ It ii I . \ ) il .'.'.' 2 ;t-, ,; ,2. ~ t:~6,,,,/;: ~i .i 11r ~,/ :~I"\ 1 . 1ll •. / , ·. /~ \ , ' 2 . ". J ,, i . . . I r. . 16 • '~( 611, '· / / 'lJ

8 - - - '.'i'J-U,f 1, . '

16 . fl-ift.~)2. 18 22 ·18. <6·- 22 2 4

6 .

\

3 6 1 , ,

••

I. 4.

3

- l 4 I 6 -18 -2 2 4 -2 2 2 6

28

-· 3 - 2.6 - 3 • 32

3.8

One-hour

5 4' 3 8 2.l 3 3 rainfall, in inches, to be expected once in IO years.

Fi9ure 5

FrntJRF,R 4 and. n. Rn!nfnll frequeney mnpR.

' I

)I, t"'I -"' 0 ....,_

"' …

? ....

tlJ

1 IQ ,,

...

... !! c.,

~ II "Cl

N

; 0 :r

~ ., Q. .. ., .c:: u

C - .=

D - C:

0 a: - 0 ,...

"' C ! .=

INTENSITY CURVES FOR STORMS IN VICINITY OF EXAMPLE SITE

9 9 I- --+--------t------t------1---- --·-·+- .. -t------. ··1----------+------l … --+-----+-- … ·--+---- 1-- -----+-·-··--··-+-- ·-·-·-·-+--·· ·• .... ··-----t-----·-1 1-----l--- -------+------+------- .. --- -t==- - I---+· --+---+----+--- ... -- 8 8 t--+---+---+ ·-t----- -•···· … - ------+-·----+----- --··· - -·---+- -----1 ----- -+-----i--· ·------+--··· 1-- -+----+ +------+-------+----····+---·---+ ------ .. ·----+-· -----------1 7~ 7

INTENSITY CURVES FOR STORMS IN VICINITY OF EXAMPLE SITE

6 t---t--'-t----11---t-----------------------------+-----t-----+-----+-----16 ---- -~------- -----·---- ------· ·---- ----- --------- ----- - -- - ---- ---~------ -··-- ···-- ----·--- -----~- ---- ---+------- ---+---~----, -- .. --+--····-·· -+-----1------1 5 1--=-~-l-l---l----+-----+----+-----4f-----+----------+-----+-----+-----4'-----+------15 --- ~--- ------ … ,

_\.~l\. 4

3 11 ~l-tM-~l-8 I I· I l ! r ·----+-·--+--· ffll~~l-=t--~~ $II I 1

3

---t--------------1 - ----+- …

2 I I I I I }=:I;;;tsts:L.J I 4 I l d· ~

---+-· -- ·---- ---. , …

-+-

… - … -- … -~---+-----· ---+---- t----t--·+--t ---+-- ... -- +· … t------------t - -----+-----+-----+-----

0 5 10 15 20 30 40 50 60 70 80 90 100 110 120 130

Duration Of Rainfall In Minutes

Frn1rnr. fi. Intensity curve,; for storms in vicinity of exnmple site.

~ 112 ..

0,

), n

u, 0 - u, "' N ? u, "'

AC 150/5320-58 Page 9

Chapter 3.

4. RUNOFF.

COMPUTATION, COLLECTION, AND DISPOSITION OF RUNOFF

COMPUTATION, COLLECTION, AND DISPOSITION OF RUNOFF

a. After rainfall rates have been studied, there remains a problem of determining what portion of the rainfall must be accounted for as surface runoff. The runoff rate depends on a number of conditions and is seldom constant for any gh·en area during a single period of precipitation. The following factors haYe a pronounced influence on the rate of runoff from an area :

(1 J Intensity and duration of the rainfall.

(21 Type and moisture content of the soil affecting infiltration.

(31 Pen·iousness or impeniousness of surfaces.

(41 Slope or irregularity of surfaces.

151 Extent and condition of ,·egetatiYe coyer.

(61 Snow coyer.

(71 Temperature of air, water, and soil.

b. Many studies have been conducted during the last few decades in attempts to deri rn a method for estimating the amount of runoff when affected by the varying factors actually met under field conditions. The studies haw coYered infiltration of soils; runoff from pa,·ement, turf areas, different length and slopes; rainfall characteristics as related to soil erosion; and numerous other conditions. Some studies ham contributed rnluable data toward a more comprehensi,·e understanding of the complex problem. "l'ntil a more rnlid method is de,·eloped for determining the

amount of runoff from girnn areas, the following is considered to be the practical course.

c. The Rational Method of calculating runoff is most universally applied and recom-

mended by engineers in drainage practice. The method has come into favor because it enables the enginPer to apply judgment directly to

Chap 3

specific determinations which are subject to

analysis after consideration of local conditions.

11 J The Rational Method is based on the direct relationship between rainfall and runoff. It is expressed by the equation Q = CIA, in which:

Q=the runoff in cu. f.p.s. from a gi,·en

area; C=a runoff coefficient depending upon

the character of the drainage area; I=the intensity of rainfall in inches per

hour; A= the drainage area in acres. The value of C to be used must be based on a study of the soil, the slope and condition of the surface, the impen·iousness of the surface, and the consideration of probable future changes in the surface within the area. The ,·alue of I to be selected depends upon the ctm·es for the intensity of rainfall plotted

for the local vicinity and the assumed period of return or recurrence, as well as the period of concentration required for surface runoff to flow from the most distant point in the area under study to the inlet structure or point of collection being considered. Design should be goYerned by the greatest intensity of rainfall during this period of concentration and not by some intensity for a shorter period. The value of A is measured and can be accurately determined. •

(21 A maximum rainfall expected once in 5 years is generally recommended for esti-

mating runoff for airports; thus, a 5-year cun·e similar to that shown in Figure 6 will usually be used. The damage or inconvenience which may be caused by greater storms is insufficient to warrant the increased cost of a drainage system large enough to accommodate a storm expected once in a period longer than 5 years.

Also, it is the recommended design procedure

Par 4

Page 10

to proYide capacity in the drainage system for direct runoff. The calculation of and proYision for ponding between runways, taxiways, and aprons should usually be considered as a safety factor-for temporary accommodation of runoff from storm return periods longer than 5 years.

Ponding of more than a temporary nature may be acceptable on the air.port site other than between runways, taxiways, and aprons. Such ponding may indeed be essential because of limitations in offsite outfalls.

5. RUNOFF COEFFICIENT.

a. The runoff coefficient or factor as it is sometimes designated, is the percentage of rain-

fall on a gi,·en area that flows off as free water. This percentage will seldom reach 100 percent, ernn with steep slopes, because imperdous surfaces absorb some moisture and small depressions and irregularities hold back additional amounts. During a storm, the percentage of runoff will increase gradually as the soil becomes saturated, the impe1Tious areas become thoroughly wet, and all depressions become filled. Then the percentage will remain fairly constant, Yarying directly with the intensity of the rainfall. The composite effect of all those factors must be taken into consideration.

b. Many authorities lun-e presented estimates for ,:Yalues of relatirn imperdousness·· for different types of urban surfaces, to be used in conjunction with their rnrious formulas. These

estimates coyer conditions applicable to the design of drainage systems for large areas, usually within urban su:::TOlmdings where the

character of surface is different generally from those on airports.

c. From these studies and other information pertaining to relati,·e impeniousness of different surfaces, Table I has been compiled which is applicable to the conditions found on airports. The appropriate runoff coefficient should be selected from Table I for use in the formula Q = CIA.

d. If the drainage area contributing to a certain inlet is composed of se,·eral surfaces for which different coefficients from this table

must be assigned, the coefficient used in the formula should be a weighted ayerage in ac-

Par 4

AC 150/5320--SB

cordance with the respecti,·e areas. For example, if a drainage area to an inlet consists of 1h acre of asphalt pa ,·ement ha dng a coefficient of 0.90 and 2 acres of impenious soil with turf having a coefficient of 0.35, the average coefficient for the total area is equal to

[(0.90 X 0.5) + (0.35 X 2.0)] -;-(0.5 + 2.0) or 0.46.

TABLE I. Value of factor "C"

Type of surface I Factor "C"

For all watertight roof surfaces … , • 75 to . 95 For asphalt runway pavements … -! . 80 to . 95 For concrete runway pavements … -! . 70 to . 90 For gravel or macadam pavements … ; .35 to. 70 For impervious soils (heavy)* … : • 40 to . 65 For impervious soils, with turf* … i • 30 to • 55 For slightly pervious soils*------------1 .15 to .40 For slightly pervious soils, with turf* __ -: . 10 to . 30 For moderatelv pervious soils* … : .05 to .20 For moderately pervious soils, with turf* ! • 00 to . 10

*For slopes from 1 percent to 2 percent.

6. TIME OF CONCENTRATION.

a. According to the theory underlying the Rational Method, maximum discharge at any point in a drainage system occurs when:

(1) The entire area tributary to that point is contributing to the flow.

12) The rainfall intensity producing such flow is based upon the rate of rainfall which can be expected to fall in the time required for water to flow from the most remote point of the area to the point being inrnstigated. The "most remote poinC is the point from which the time of flow is greatest. It may not be at the greatest linear distance from the point under im·estigation.

b. The time at which maximum discharge occurs is referred to as the time of concentra - tion. It is composed of two components re-

ferred to as the "inlet time'' and "time of flow''. The "inlet time'' is the time required for water to flmy oYerland from the most remote point in the drainage subarea to the inlet. The "time of flow" is the time during which water

flm,s through the drainage system to any point

Chop 3

AC 150/5320-58 Page 11

: .i...t• ~-'-- ,----::::::.:= Use Formulo For ++...., … , … --+- … ,Hf<""T"iH-+-t---+-+-+-<-i,1"--,-+.-.,..- … ,,-..,..+++-++.-,-+-+""-i so Dist onces in Excess: 600

0 ,- w w .... z

w u z < ,- v,

0

Of 800 Feet.

----...J .,. __ -~ 500 --,--------+----++-,---+

400 - --

50 ...

V, w ,-:i 40 z ~ f w ~ .:: 30

10

0

Surface Flow Time Curves

Fwnu: 7. Surface flow time curves.

being im·estigated. In some instances the "inlet time·, will be the time of concentration.

Such is the case for an inlet at the upper end of a drainage line.

Chap 3

(1 l Furthermore, a condition may exist where the "inlet time" to a structure along the line may exceed the time required for water falling on a more distant subarea to reach that

Par 6

Page 12

inlet. All areas tributary to the particular structure are not contributing until such time as water is entering the inlet from the most

remote part of the individual subarea which it sen-es. The time of concentration, therefore,

will be the "inlet time. i• Problems which arise in this regard will ha,·e to be im·estigated and resoh-ed individually to determine under what conditions of time and flmv the maximum

volume of water can be expected at the point studied.

(2) "Time of flow'' can be determined by hydraulic computation, i.e., by dividing the length of pipe by the rnlocity of flmv.

(3) The "inlet time,·· C'Onsidered one of the most important factors in determining runoff, will rnry with surface charaderistics of the drainage area. The cun-es or formula in Figure 7 wi11 prm·ide adequate estimates of "inlet time'' for the designer. rse the formula for distances in excess of 800 feet. 1,11ere the particular drainage area consists of several types of surfaces, the "inlet time·· must be determined by adding the respectirn times established for flmv ornr the length of the

seYeral surfaC'es along the path from the most remote point to the inlet.

7. COLLECTION AND DISPOSAL OF RUNOFF.

a. Before any definite computations C'an be made toward the actual design of the drainage system, a topographical map wi11 ham to be

prepared shmving actual ground contours existing on the airport area. The contours preferably should be drawn to a 2-foot interrnl. This map should be extensive enough to show the areas surrounding the airport boundaries with a1l natural watercourses, swales, draws, drainage structures, ditches, slopes, ridges and configurations. It should also show all imprornments that might ham a bearing on the runoff and drainage of the immediate area, such as railroads, highways, canals, and irrigation and drainage instaJlations.

b. An additional detailed plan is necessary to show the proposed and ultimate layout of the runways, taxiways, aprons, and building area with the finished contours drawn to a

I-foot interrnl or less. This plan can be the "drainage working drawing." The entire sys-

Par 6

AC 150/5320-SB

tern should be sketched upon it, with the outline and identification of each single suharea, all main and lateral storm pipelines, pipe sizes, direction of flow, gradients, catch basins, inlets, manholes, gutters when required, surface channels, peripheral and outfall ditches, and other essential drainage features.

c. The finished grades in conjunction with the drainage design are very important. The location of the runways, taxiways, aprons, and building area is usually fixed by the time the drainage design is started ; but the cross sections of the paved areas, their profiles, and all the grades of intermediate areas should be carefully studied for their influence on the drainage layout. It is important that all finished grades be established so that eYery area is drainable and so that the runoff can be collected by some drainage facility.

d. The primary consideration, therefore, is the determination of a satisfactory drainage arrangement at a reasonable cost, im·oh·ing the location of the shallow channels, inlets, catch basins, manholes, selection of grades, etc. Trial computations of several different drainage layouts should be made in arriYing at the most practical design. "\Vhen all arrangements for location of the inlets, shallow drainage swales, and storm pipes have been plotted upon the drainage working drawing, a tabulation of data and computations should be made. Such a table is further discussed in Chapter 5.

e. Normally, the inlets should be located at least i5 feet from the edge of the pavement at airports with scheduled air carrier operations and 25 feet from the edge of the pavement at airports used exclusively by general aYiation. If inlets are placed close to the pavement edges, they may be bypassed by the flow of water.

Also, no ponding would be possible because the impounded water could back up to the edge of the paYement and cause saturation of the subgrade. The grading should be planned so that the inlets can be placed normally at the edges of the runway safety area or in the area midway between the runways and the parallel taxiways. The runways and taxiways should be crowned. Beyond the paved edges, the slopes should be in accordance with design

recommendations. In establishing grades out-

Chap 3

n =r Q "ti ..,

l ...

,._,~ NOTES.

/

, -------- The dimensions ond grades shown here moy be used only

..._0<:i" • ~ oulside of the runway safety oreo,(londing strip) or to~,-

/ C,' / ~ , -__ woy safety oreo. Longitudinal grodes, longitudinol grade / / ~ '. t changes, vertical curves and distance between changes / / ~ ---.. for that part of !he runway safety area belween run-

., ~ ~ ~ - and stopways [!]/ -~ --- -------1 \.;r woy ends ore the same as the stondords for runways

: __- ~ ~ Ridges provided for ponding areas within the runway - · I 5,. Slope - • ~-- JO'l'. Slope g- 3 '- Slope safety areo sha 11 conform to such stondords. Heodwalls,

:.._ ' ~ - ~ ~~ - culvert pipe ends, and other slructures wilh prolrud1ng … '- … -- … jJ vertical faces shall no! be permitted within runway or :::::t ~~ "~ ~ =-·,,; .. , "'"' '""

£'..LAN o..,,. ~ }---- --- , / --

E119835' ~

El 20.15' -~loo. El 19835' 1 I r£11985' -·--• · ~ El 19 85'

0~

20' J' IJ'-4"1 3·

-- - ~t,nuou, 1 SAMP~E PROF IL~ I -..c. - ~ ~o.e_e __

The percenloge of !his slope should be

reduced when proclicoble.

-------

----1~1926

… JO' _ 2+-- … 101'

Pon~(ng … ·---------------T

_QROSS SECTION

_QROSS SECTION

Suggested Grading For Smal I Ponding Areas On Continuous Line Of Inlets

FIGURE R. Snggested grading for small ponding nrens on contlnnous line of inlets .

-,.,

0 ,..;

> n

u, 0 … u, .., .., ? u, "'

l ..

w

Page 14

side of pa rnments, the soil characteristics should be considered so as to aYoid erosion and promote infiltration. Less grade is used for sandy soils than for other soils. A slope of 5 percent should be used for a IO-foot width adjacent to pa rnment edges to facilitate runoff.

f. It is desirable to proYide for ponding areas around inlets as temporary storage for runoff from the occasional storm which exceeds the design storm. If seYeral inlets are in the same graded area, it is appropriate to design a ridge between the inlets to prernnt runoff from bypassing the upper inlet. These ridges and ponding areas must be designed to aYoid unacceptable grades and grade changes within

runway and taxi,rny safety areas (see Figure 8).

g. Inlets should be placed at all intermediate low points created by grading the airport. In the case of a long run of surface drainage

where the fall is all in one direction, the inlets should be spaced so that the runoff will not tranil excessirn distances before reaching a structure. Xormally, inlets should be spaced so that the flo.y from the most remote point of the drainage area is not more than 400 feet.

h. :\Ianholes, or combination manholes and mlets, should be prm·ided "·here necessan: their spacing should approximate that for i

0 nlets. In good drainage practice, manholes should be placed at all changes in pipe grades, changes in pipe sizes, changes in direction,

junctures of pipe nms, and at reasonable interrnls (approximately 300 to 500 feet) for cleanout and inspection purposes. ,Yhen it is impractical to haYe manholes approximately 400 feet apart on subsurface systems, then lamphole risers should be installed to allow access for obserrntion and flushing. (It may be noted that the drainage design example of paragraph 19, Figure 33, and Tables IY and Y contradict the principles of this and the preceding paragraph to spacing and location of inlets and manholes. The contradiction is deliberate and was made in the interest of simplifying the example).

i. All natural w·atercourses, draws, and outfal)s should be accurately spotted on the drainage working drawing, and the drainage system should be planned so that as many of these

Par 7

AC 150/5320-SB

watercourses as possible can be used for outfall and rapid remornl of the runoff from the air-

port area. This procedure is necessary to pre- Yent concentration of all the airport runoff in one or two outfalls and flooding of property

below the airport site. By use of several outfalls when they are arnilable, the cost of the system can be held to a minimum by reducing pipe sizes and by shortening the discharge pipe runs.

j. Open peripheral ditches should be used, whenerer practicable, to receiYe outfall flow from the drainage system, to collect surface flow from the airport site and adjacent areas, to intercept ground water flow from adjacent higher terrain, and in many cases to aid in lowering the ground water table. These open

peripheral ditches should not be constructed where they will cross the rummy safety area

(landing strip) or extended safety area. The flow across this section should be placed in conduit for at least the width of the safety area. Before a system of peripheral ditches is

planned for an airport site, the soil should be examined to determine whether the soil will erode. Open ditches haYe a tendency to erode

because of the concentrated flow. Ditches should not be constructed where the airport is located on sand unless they are absolutely necessary, and ernn then, they should be shallmY ditches with flat slope and immediately lined with sod or otherwise protected to pre-

rent erosion.

k. If the outfall drainage cannot be emptied into existing watercourses or natural drainage channels, or if the quantity of water is greatly increased oYer normal flow, easements or agreements should be obtained from the affected

property owners to aroid future contrornrsy.

8. FLOW IN CONDUITS. a. After the locations of the inlets, manholes, pipe runs, and outfalls have been determined and the design runoff for all sub-

areas has been computed, the next step in the design will be the computation (by appropriate hydraulic formulas) of the size and gradient

of the pipe drains. Also, the "flow time'' in the pipes frmr. the rnrious inlets can be computed according to the hydraulic characteristics of the pipe.

Chap 3

AC 150/5320-58

11 l Several formulas are used by engineers to determine the flow characteristics in pipes. Many of them girn practically the same results, but the Manning formula is the most widely used and is recommended for use and is as follows:

Q = A 1.486 R2/3 5112

n in which:

Q =discharge in cubic feet per second A= cross-sectional area of flow in square

feet R=hydraulic radius in ft.=area of section

wetted perimeter S=slope of pipe im·ert in ft. per foot

n=coefficient of roughness of pipe

(2) Charts have been compiled for the solution of the Manning formula. They usually are used instead of the formula to determi1;e the size of pipe required. Figures 9 to 12 inclusive show these charts based on :Manning:s formula for discharge of circular pipes flowing full, with slopes from 0.0001 to 0.1 feet

per foot, and values of "n'~ = 0.012, 0.013, 0.021, 0.023, 0.024, 0.027, and 0.031. The selection of the rnlue of "n'~ in Table II is also a matter of judgment. The value selected should represent conditions which will prevail during the useful life of the line.

b. The design engineer should keep in mind that it is important to maintain sufficient velocity within the pipes to prHent depositing of suspended matter washed into the system through the inlets. The velocitv of flow in pipes depends on the head or slope and the resistance to flow of the wetted portion of the pipe interior. The head or slope used in design always refers to the position of the hydraulic gradient, which is the line assumed by the top surface of the flowing water when fr~e to rise vertically. The wetted portion of the pipe interior is used in determining the hydraulic radius, which is the area of the inside of the pipe di,·ided by the wetted perimeter. The mean velocity of flow is used in determining the size of drains.

11 l Some engineers, when designing drainage systems, do not differentiate between the slope of the i1wert of the pipe and the hydrau-

Chap 3

Poge 15

lie gradient of the pipe run. The. hydraulic gradient should be considered in the design of storm drains because it is used in the solution of velocity and discharge. The hydraulic gradient at the upper end of the line should be established near the elevation of the inlet grate. The ponding volume may pr<>4uce at times a higher elevation of the hydraulic gradient at this point.

(2) Past experience shows that a mean velocity of 2.5 feet per second will normally prevent the depositing of suspended matter in the pipes: Economy of design and topography will control the velocities. When lower velocities are used, special care should be taken in the construction of the system to assure good alignment, straight grades, smooth well- constructed joints, and proper installation of structures. The pipelines and slopes should be designed, wherever possible and when topographical conditions permit, so that the velocity of flow will increase progressively or be maintained uniformly from inlets to outfall. Thus the suspended matter will be carried through the system and out the outfall end.

c. The conduits in the drainage system may be constructed of reinforced concrete, concrete ,-i.trified clay, corrugated steel, corrugatea" aluminum alloy, or asbestos-cement pipe. The pipes should be of conventional standard sizes and provided with either bell-and-spigot or tongue-and-grom·e joints in the precast pipes, adequate metal bands for the corrugated metal pipe, and couplings for the asbestos-cement

pipe.

d. The chemical characteristics of water and soil which might affect the durability of drainage pipes should be investigated. The type of pipe least affected by those chemicals should then be recommended for installation.

e. Bituminous coated, partially or fully paved corrugated metal pipe should not be installed where fuel spillage, wash-rack wastes,

or solvents can be expected to enter the pipe. Such coating or paving is soluble in aircraft fuel and some aircraft washing liquids. Such liquids are also flammable, thus a fire carried into the pipe would damage the pipe seYerely. Design of the drainage system for aircraft

fuelling aprons should:

Par 8

Page 16 AC 150/5320-58

(1) PreYent spread of a fuel spill to structures, passenger loading fingers, or concourses, which could result in the fuel or vapors therefrom reaching a sourse of ignition or might release dangerous or toxic yapors within the structure itself.

(2) Prevent spread of a fuel spill over large areas of the apron surface and the transmission of vapors, which may expose a number of aircraft or other equipment on the apron.

(3) Provide for the safe disposal of fuel spillage.

These objectives may require consideration of one or sernral means. For example, the apron should slope away from buildings. Inlets should be located to allow reasonable flexibility in parking of aircraft without the likelihood of aircraft being positioned over inlets. Sections of drainage systems should be isolated at interrnls through use of water seal traps or interceptors or separators to prevent transmission of flame or vapor through the system.

TABLE II. Coefficient of roughness

PIPE

Clay, concrete, and asbestos cement … Corrugated metal

Fully paved----------------------------------------------------------------------- 25% Paved, 2% x % inch corr … 3 x 1 or 6 x 1 inch corr … 6 x 2 or 9 x 2~ inch corr …

Unpaved, 2% x }finch corr------------------------------------------------------ 3 x 1 or 6 x 1 inch corr … 6 x 2 or 9 x 2 % inch corr … 2 x % inch helical corr 12inch diarneter----------------------------------------------------- 18inch diameter---------------------------------·------------------- 24inch diameter … 30 inch diameter to 48 inch diameter …

OPEN CHANNELS

OPEN CHANNELS

Paved

Maximum Permissible Velocity in Feet/ Second

Coeffic. "n"

0.012

0.012 0.021 0.023 0.026 0.024 0.027 0.031

0.012 0.015 0.017 0. 018 to 0. 021

Coeffic. "n"

Concrete __ ---- … ----------- … 20 to 30+--- … 0. 011 to O. 020 Asphalt … 12 to 15+------------------------ 0.013 to 0.017

Rubble or Riprap … 20 to 25-------------------------- 0.017 to 0.030

Earth

Bare, sandy silt, weathered … 2,0 … 0.020 Silt clay or soft shale __ • … 3. 5 … 0. 020 ClaY------------------------------------------ 6,0------------------------------ 0.020 Softsandstone … 8.0 … 0.020 Clean gravelly soiL … ---------- … 6. o … O. 025 Natural earth, with vegetation … 6,0 … 0. 030 to 0.150*

Turf

Shallow flow … 6. O … O. 06 to 0. 08

Depth of flow over 1 foot … 6,0 … 0,04 to 0.06

*Will vary with straightness of alignment, smoothness of bed and side slopes, and whether channel has light vegetation or is choked 'll'ith weeds and brush.

Par 8 Chap 3

AC 150/5320-58

<fl

LL

0

z

w l!) 0:: 4 I 0 <fl

0

1000 900 800 700

600

500

400

300

200

100 90 80 70

60

50

40

30

20

10 9 -8 -7

6

5

4

-3

2 5

120 1 .0001 .0001 I 108 J 96 -f 0002 90 --1 84~ .0002

78_j b- 0003 .0003 --} 0004 72 ._j 66--j -0004 ---r- ' 0006 601 .0005 <fl (\J .0006 0008 ,., w 54 … - - I

48~ 0 .0008 0010 0 0 0 z ' 0 0010 I " 42~ " t ' C C 2 39j '- 0020 - 36 I 0020 ---t a: 0:: z 33~ 0 ~ 0030 0 - LL r LL <( 30-i .0030 -f- 0040 0:: ' 27....j L 0 w 0040 ~ w I Cl. .0050 ---c- .0060 Cl. ' LL 24 ---< 0 - 0 ' ....J 0060 ....,:._ 008 0 ....J 0 I 21-I <fl

0080 * 0100 <fl a: 0010 ..Jw 18 f- I- • w ' -{ 0200 ~ 15 <( 0200 I 0300 D

121 0300 0400 .0400

10~ .0500 0600

8j

0600 ;;:-0800 .0800 1000 .1000 I

6J

N omogr oph for computing required size of cir cu !or drain,

flowing full - n • 0.012 OR 0.013

2

3

C. l.. /:--4 ..

5

~

~ i:-6 ..

7

8

9

10

II

12

13

14

15

FIGl..RF: 9. ~on10graph for con1puting required size of eircular drain for n 0.012 or 0.013.

Page 17

D z 0 0 w <fl

0:: w a.

I-w w LL

z -

>- I-- 0 0 ..J w

>

Chap 3 Par 8

Page 18

en ~ 0 z

w (!) a: <( :I: 0 IJ')

0

400

300

200

100 90 80 70

60

50

40

30

20

10 9 8 7

6

5

4

3

2

.000 I

.0001

.0002

.0002 .0003 120 .0004 0003 108 .0005 .0004

96 .0006 -0005 90 .0008 .0006 84 0010 .0000 78 t\i 72 v .0010 (\J q 66 0 0 60j 0 0020 • IJ') 0020 C w • :I: 54 ~ C 0030 0 .0030 a: 48 .0040 0 z a: 42j 0 0050 0040 ~

~ .0060 0050 z 39~ w 36 .0080 0060 Cl. w .0100 0 33-j Cl. .0080 z ..J "l

0 .OIOO IJ') <( ..J a: 27 IJ') 0 0200 24 ~ 0200 0 21 .0300

.0400 .0300 a: 18 .0500 w 0400 I- 0600 .0500 w "j

.0600 ~ .0800

<( 1000 0 12

10

8

6

Nomograph for computing required size of circular drain,

flowing full - n =O 021 oR 0.024

AC 150/5320-58

1.5

2

0 3 Z 0 0 w IJ')

a: 4W Cl.

I-w w 5 ~

z

6 >- I- 0 0 7 ..J w > 8

9

10

II

12

13

14

15

FIGrRE 10. ~omograph for computing required size of circular drain for n 0.021 or 0.024.

Par 8 Chap 3

,

AC 150/5320-58

400

300

200

100 90 80 70

61'

V> 50 ,.,_ ._, 40 z

w 30

I.? a:: <l :i: ._, 20 (/) - 0

10 9 8

7

8

5

4

3

2

.0001

.0001

.0002

0002 .0003 120 .0004 0003

108 0004

96 .0006

90 .0008 0006 84 .0010 ... 0008 .., 78 N N 72 0 .0010 0 ci 0 66 .0020 .

C C 60 0020 a:: .0030 54 a: 0 0 ,.,_ .0040 .0030

,.,_ 48 w .0040 w (/) 42 ll. .0060 ll. w 0 0 :i: 39 ...J .0080 ...J ._, "' 0060 (/) z 36 .0100 33 0080

~ 30 0/00

z 27 <l .0200 a: 24 0 .0300 .0200

,.,_ 21 0 0400 .0300 a: 18 0400 w .0600 Iw 0800 .0600 :I! 15 <l - 1000 .0800 0 12 .1000

10

8

6

Nornogroph for computing required size of circular drain

flowing full - n=0.023 oR 0.027

FIGl:-RE 11. ::--omograph for computlng required size of circular drain for n 0.023 or 0.027.

15

2

3

0 z 0 0 w (/)

4 a: w ll.

I-w w ,.,_ 5 z - >- I- 6 0 0 ...J w > 7

8

9

10

I I

12

13

14

15

Chap 3 Par 8

Page 20

1000

500

400

300

200

en ... u

z - w

<.:> 100 a: 4l X u .,, - Q

50

20

I 0

Par 8

. 000 I

.00(12

.0003

.0004

.0005

0008 .0010

120 108 .0020

96 . 0030

84-· .0040

78 D06il 72 66 .0080 60 .0100

54 .,, 4& .0200 w

% u 42 z .0300 -z 36 .0400 - z - 30 .0600 "' er .0800 0 27 er .1000 24 w ... w 2 I 2 "' - 0 18

15

I 2

10

8

6

NOMOGRAPH FOR COMPUTING REQUIRED

NOMOGRAPH FOR COMPUTING REQUIRED

SIZE OF CIRCULAR DRAIN

FLOWING FULL

-.., 0 0 " C

a:

0 ...

w ...

0 ..J V,

F1GrRE 12. :Kon1ograph for computing required size of eircular drain for n 0.031.

AC 150/5320-58 J

2 -

I

3 0 z 0 u w V,

a: w ... 4 .... w w ... z - 5 >-... u 0 ..J 6 w >

7

8

FLOWING FULL

9

10

Chap 3

AC 150/5320-58

9. FLOW IN OPEN CHANNELS.

a. For our purposes, an open channel is defied as any conduit in which water flows with a free-water surface such as an open ditch, creek, rirnr, or canal. Although pipe drains act as open channels when flowing partially full, they are considered separately in paragraph 8 and elsewhere in this publication.

b. It is recommended that maximum use be made of open channels because of the relatirnly low cost thereof as compared with capacity attained. Obviously, open channels need to be consistent with safety and operational require-

ments of the airport. Channels shall be of adequate capacity and free from excessive maintenance which could result from erosion, silting, or steep back slopes. In the latter connection, it is noted that mowers cannot normally be used on slopes steeper than 2.5 to 1. Slopes steeper than 2.5 to 1 will usually need to be cut by hand or cut by mowers restrained by other equipment at the top of the slope. Some areas of the country, where soil is generally noncohesirn and ,·egetation is likely to

be sparse, use 3 to 1 as maximum.

c. The Manning formula may be applied directly to hard surfaced channels of concrete, corrugated metal, etc., and to earth channels

using coefficient of roughness Yalues for "n" as shown in Table II. That table also lists maximum permissible Yelocities for such channels.

d. A nomogra phic solution of the Manning formula can be made by using Figure 13. The channel-dimension diagrams for trapezoidal, triangular, and parabolic shaped channels, Figures 14 through 19 permit rapid solution of many ordinary channel problerr,s.

e. The Manning formula is Q = AV where:

Q = rate of discharge or flow in cubic feet

per second. A= cross sectional area of the flow m

square feet. V=l.486 R2/3 Sll2=velocity of flow m

n feet per second. n = coefficient of roughness.

Chap 3

R=hydraulic radius in feet or cross sec-

tional area A divided by the wetted perimeter. S=slope of energy gradient in feet per

foot, considered equal to slope of channel bed for most situations.

f. The following indicates the use of the channel-dimension diagrams in Figures 14 to 19.

Cl I For example, given Q = 100 cubic feet per second and S = 0.0002 feet per foot.

Find: The bottom width, depth of flow, and velocity of a drainage channel with 2.5 to 1 side slope. Assume channel will be maintained regularly and kept free of excessive vegetal growth. Estimate "n" to be 0.04. ( See Table II for open channel "n" values).

Solution: Requires one or more trial solutions. The steps are: (a) select a velocity, (b) compute the area required from Q/V, ( c) determine the required R from the nomogra ph of Figure 13, and ( d) determine the bottom width and depth from the 2.5 to 1 dimension diagram of Figure 14.

Item Trial Solution

1 Y = feet per second (selected) 1.0 A=square feet (from Q/\') 100 R=feet (from Figure 13) 2.60 b=bottom width in feet 20 (from Figure 14) d=depth of flow 3.6 (from Figure 14)

2 3 0.9 0.95 111.1 105.6 2.20 2.40 3G 28

2.6 3.1

The solution chosen will depend upon depth and botom width of channel desired. If still not satisfactory, change V slightly and redetermine dimensions. Final selection of channel dimensions must consider addition of reasonable free.board to depth of flow.

(21 For example, given Q = 50 c.f.s. and trapezoidal channel with side slopes of 3 to 1

and bottom width of 10 feet.

Find: The bed slope required to maintain a velocity of 2.5 f.p.s. Use "n'' = 0.04.

Par 9

... ~ ,0

n :r Q "lJ

w

I R 10 • • 7 •

5

4

3

2 ... ..: ...

C

"' :) ·r~

• c··

.• u ;j .T :> • .. ~ ,. %

.II

,.

.3

.2

… -

~ "' 1.0 "·

.. .,

.2

04 .03

.01

I• O.f 11, Oft 0.00& ,1 H• ,T. flTUU,Tl.0 a • G,C,4 v • I.tr ,,. ~r• •re.

n

f'IVOT

LIN£

I

V

.01

Ot

.()3

.04

.()I .oe

.I 'i

c.i '"' .3 ... :: i

...

C r .. ::.:

..,: ...

> t j . ..---······· ----··"'·· -· - ----- 3--· --:=··············

4 u

… 0 .J ...

MANNING FORMULA

MANNING FORMULA

0 .J ' ... • >

10

to

JO 40

V • l.48S R11aS111

n

Fwunr;: rn. Solution of th<' Manning formula.

a" co … I s

.00001 .0000. .ooooe .0001

.ooot

.0003

.0004

.OOOI .OOOI .001

.oot

.003

.004

.OOI

.OOI .01

.02

.03

.(M

.OI .oa .10

.10

I ), ~ ;;: 0 -... "' c., ... 0 I "' 0,

.OOOI .OOOI .001

n .,. Q ... ...

e •

t

ac

CII ::> i5 c( ac

u ::i ::> c( ac 0 >- :i::

· · . ·1 'I I 'f'ft;jffl 3,tlJ :r·,· I TI '11 .. 111 .. I I , I I l 11111 I : : <,jl~ ctm1J

,h

1'.oo r L .rv 1 1 1 1 1

d; 1111111~ II 1111111[ 11 1~0"

s

41: I I 11111~ 1

l

LS

..

I

7

I '

.4

.a

11 .l

I J • 5 • 7 • I IO

AREA I A • SQ. FT.

,11 > ,~>. 1 111: 1 I :!00

,11' < ~I .. I 1,11!.oc, > ,r,~

I 1 111

11111 II 11''1 IO

II 11

11 11 I' 111 I :,00 11' • ,11'1 • ,, 7

,,,1111000 ii"' ,0 .. , ,11 tlO

11 1 10 L ..

1 1111• ~ .... 1111 IO ..

1 1111

1,1 1 so 1•' 11 11-o 111

II~ 11

I IIIO

, …

c,O·

111.,

I I

LS

1111111

111 '

1 ,,11' 11 I 4 I' 1'' , … 11' , , 1 I> II

1 11 ~ .... ~ i I o<,;

1,,1t1I~

l'I 111 I :,0

11 11 1 1 ~ ~,,I

/11_,1''1 l

,111.~ ~ ,

111111h1l~1 ""-- --- ~ ZJ I

1,11 I 41 4 CSJAQ J)l 21 … WMJ..Jlu,.,l.1.lullu.lullu.l1.1U.ullwllwll

1111 • I I .l .J .• . • b ...

-.,..

FIGURE 14. DlmcnslonR of trnpczolclnl chnnnelR with 211.i to 1 Ride Rlope.

,. n

"' 0 …

"' … ? "' "'

l •

N w

l

~

,0

g

Q …

…

a:

• "' :,

0 .. a: ...,

...J :, .. a: 0 >-

I:

I r1r1pn1 ,

• I;- l l -I I -+ I 1

5

•

J

2

I ' t--

l ., • ·' ' 5

•

J

1----1- ~-------.J +- ---- ---t

- - + 7<

. I 11 Lr:, !I llllll r J •

t

- - _ j ..

I I t ·1-

ttltl -~

I ~

-- ~ T

I j I . l .,o'¥<_

,~- y. ·o' ~ - \ e: - =i· 1- ~

!.•1190

~

"

I

AREA , A, SO.FT

i

I ,·---

•

.I I --+-- - ' 1 I I 1----~~ l

I . I J , , ,

j I ' ,1

1 100 -\ . ,I•''°

, , 1 , 1'•0 """" ! f 11• fO ..,..q... l,,)''I~

AREA , A, SO.FT

1. , I. ',o . ' I,. ..,

I ' I ' , ro

I

I I '' . ' I•' lO

•

,, ,1900 I 11 ,,_,., I' , , 1l)O JI I ,,,,..,., , ,,

I I ' I 1tOO

I I , ,

I ' 1•'' "'° I I

,,

I,, I

I ,, ,00 , , '. ,,,,_

I I ------ ,r.n 'oo

~ •

~" ~· c;

-- b?W' / -,.'1

·;,4 f-l I 1 I 1 ! t

- 11 I ' fi

,. rl' I ' I . O I f

- 1· 1,/' ,' ' ,, 1,,,,, , , ,

I 15

I I I t

q"-~ .

Q(r.;

-

.. , ,,

[l/JJl!lJ!IJJ11

11 .4 r .,

Frouni.; 15. Dimensions of trnpezoldnl channelR with 8 to 1 Ride slopes.

• b

,,

" . ~

3 I

.,, Q 1/J " N ....

> n -"' 0 … "' ...

N Q &

Ill

AC 150/5320-58

Chop 3

- .

-~~ -'"-+'"--"~>.-+----------==- ..

-

---=

~:k"d<-"'v- … -t-------"""-"':;;.,o

-+:"<"i~!->.----+.------==--==-..

- I

l!Wl'"~....w.f-'~~~t>.t- … ,"""a E--+--+--"""" … ,.~.µ..- … ;...,_ _ a

. -==-__ i

. .. ..

-t',N~"'t---",;cr--------'--=-=;-

"!

'l.j ' ti sntOYtl :>11nYt10AH

Page 25

!!

-:

Par 9

Page 26

Par 9

--

-- --- ,,, -

0 b-,-..-,-h-,r.-r+-T-r...--.rt.., … ,,...-.-..--fn.m-= 2

• xv'

' ,0

,n ... ----

1.---lt+-\--l,l-'~---;l.----+-+--+-l~--= ~

~--fr-\-l-\-~t--lt-\--\--1l-t'..-t---= i --

'

-s-..,

<>"',¥, 0 ... - -

- &---+-~ -->,.->,~~-->r--t.--\--'.--lt--= i -

• --o ,--- N

--

N - "' … • • -

AC 150/5320-58 I

•

'

...

:.. - •• --

·-

·-"' -- c.; • E ·-0

•

--. ---

... ...

Chap 3

AC 150/5320-58

Chap 3

l t

..

,,.

~ .. --

...

lC ..

lC .. i z 0 ;::. u z :, ... z 0 u

!

0 ... "' :, "' ..

0 … C C lC u "' i ..

ii

,._; ... .. 0 ...

C

C "' f--~-+~~-+~~+-~~--+--+-+-+~f---+~+.~-+~~--''1.--~-+....>.,~~-:

.. - … ~

0 .; i;: -

z 0 ;::. :, -' 0 "' u i ... C II: " 0 2 0 z

Page 27

r,; ,:: 0 "ii.

§ E i5

,., 9

... a

~ .c,

n ,.. a ,:,

...

1

6

5 •

s

t

I ' • . 7

I

s

.4

.S

.t

d

.. ..

..

•

X .. .. w 0

a … % "' u

NOTt:

t PIVOT

L Ill E too~ '

l!IO i l .. 100 __J .. :1

~ I

• - . . ~ ... I 40 X .. 'SO .. I ..,

0 to .. .. - .. J: ..

10 ~

0 -II

I I ' '

II

[XAlll'LE

f..-- - . - --- -· . ' . J •. . t • ,, . r,•1110.1,•Dl r -·.

I ... ·--t•Jf'- t .... • I I I • -.. I • t •••.

.> '::::Ji .. ,

THIS CHAIIT TO IE USED TO OBTAIN OTHEII DIMENSIONS arT[II '- AND 4 ,011 IIAlltllUII

FLOW HAVE ll[[N O[T[AIIIN[O (FROM FIG. 181

FLOW HAVE ll[[N O[T[AIIIN[O (FROM FIG. 181

l•'1Gnnr,: JP. Solntio11 for 1limP11RionR of r,arnholl<'. chnnnPls.

SIDE SLOPE

10 I

t I

I I

1.'

I. I

S· I

4 I

] · t

t '

I · I

"' .. 0 .J ..

"' 0 -..

.J "' " " .. :r u

"' .. .. JI .. f ..

... a ca …

""

,. n -"' Q -"' …

? "' OIi

AC 150/5320-58

SIDE SLOPE

1.6

1.4

I- 1.2 l&J l&J IL

~ 1.0 ir .,, ::, a 0.8 < II:'.

~ ...J 0.6 ::, < II:'. a >- 0.4 :I:

0.2

0

t------------.g- ---1--++---#'--- … t,---,--1----t

qi,,/ 0 ~--J'-+--~1---+--,'"'+-,,,'---t~---t-.,,."---t 1,,/-J 01\t

~~ ? ,rt--------0~----- … --..,..-----

0 0.1 0.2 0.3 0.4

RETAROENCE COEFFICIENT n

GRASS COEFFICIENTS (Kl FOR DENSE AIRFIELD TURF

GRASS COEFFICIENTS (Kl FOR DENSE AIRFIELD TURF

AVG LENGTH OF GRASS IN INCHES GRASS SPECIES

<6 6-12 >12

BUFFALO 1.6 -- -- BLUE GRAMMA 1.5 1.4 1.3 BLUE GRASS 1.4 1.3 1.2 BERMUDA 1.4 1.3 1.2 LESPEDEZA SERICEA 1.3 1.2 1. 1

EXAMPLE:

DETERMINE n FOR 4-INCH BERMUDA GRASS CHANNEL WITH R = 0.9 ANO S = .010.

AVG LENGTH OF GRASS IN INCHES GRASS SPECIES

FROM TABLE K = 1.4 AND FROM GRAPH, FOLLOWING DASHED LINE, n IS EQUAL TO 0.125.

FIGFRE 20. Retardence coefficients for flow in turfed channels.

0.5

Page 29

Chap 3 Par 9

Page 30

Solution: The area required is Q/Y or 20 sq. ft. Enter Figure 15 with A = and b = 10, and find that R = 1.08 feet. Then in the nomograph, Figure 13, extend a line from R = 1.08 through n = 0.04 to the pivot line, extend a line through the relocity scale at 2.5 to the slope line. The slope required is found to be 0.00-! feet per foot. Depth of flow from Figure 15 is found to be 1.45 feet.

(31 For example, given an existing channel with side slopes of 3 :1, bottom width 12 feet, depth 3.5 feet, bed slope 0.0008 feet per foot. Channel has not been well maintained and some willows and other ,·egetal growth exists, therefore, estimate ,:n ·· to be 0.06.

Find: Present capacity allowing a 0.5foot freeboard.

Solution: Depth of flow will be 3.5-0.5 or 3.0 feet. From Figure 15, R = 2.05 feet and A = 63 square feet. From Figure 13, V = 1.15 feet per second. Then Q, as channel capacity, = 63 X 1.15 = 72.45 c.f.s.

g. "\'11en the channel is to be lined with ,·egetation, the design problem is complicated by a regetal retardence element, which is a

function of both the turf characteristics and the depth and relocity of flow. This retardal element or coefficient of roughness Yaries with

VR, the product of relocity and hydraulic radius. The degree of yegetal retardence depends on the height and density of cover, particularly the height.

)lost drainage references include 4 or 5 degrees of retardence, which are related to type and height of grass in the channel. As shown by Figure 20, haring a known hydraulic radius, slope of channel, and selecting a grass coefficient, one can obtain a retarµence or roughness coefficient.

10. STRUCTURES.

a. The structures usually built in connection with airport drainage are quite similar to those

Par 9

AC 150/5320-SB

used in municipal construction. Generally speaking, the standard types are adequate, but occasionally a special type of structure will be needed. Structures located in the usable ar~as on airports should be so designed that they do not extend above the ground level. The tops of such structures should be one or two-tenths of a foot below the ground line to allow for

possible settlement around the structure, to permit unobstructed use of the area by equipment, and to facilitate entrance of surface water.

b. The structures most generally used are inlets, manholes, combination manholes and inlets, catch basins, lampholes, and headwalls. Some of these structures will be covered with a grate when it is necessary to admit the surface water into the system. The grates may be of cast iron, steel, or ductile iron. Se,·eral suggested designs of grates and inlets are shown in Figures 21 and 22. For suggested headwall details, see Figure 23. Precast and manufactured headwalls are available.

c. The general designs of drainage structures used by the municipalities are quite alike; howerer, almost e,·ery large city has its own special standards which vary in details according to the desires and ideas of the design engineer.

These structures all vary as to the design load they will support and should be thoroughly checked for load-carrying capacities.

d. In aircraft traffic areas, grates and frames should usually be specified to support loads

from aircraft which will use the facility as these loads normally exceed those imposed by maintenance equipment or other traffic. Although roadway type grates used by the municipality or highway department will certainly be adequate for all single gear and some dual gear aircraft, it is apparent that most dual and dual tandem gear aircraft weigh far more than highway vehicles and have higher tire pressures. Representative takeoff weights and tire pressure are:

Chap 3

AC 150/5320-SB Page 31

0 )f -rFillet weld 1! ~r Fillet weld O 0 8 I i[JDDDDOJ

=---.

I '

g- :woooorn ';.,, c,, C

! OJOEJ[B)O[D i I c "'

4> 4> 0. u 0 lliJD@~orni

0 0. .; <fl E iOJOOODDJ[

C1> _,..

~ 0

rt') B !0]0000[]11

B <t "'

A l_

3" it<'l 1' 11: .-=-- ,,

Ii i IJ: I'

Ji i:

1, 11 ,1

J I 3 1" 3'" ,.. ' 0 j",3f'Bors ~ ~ • r 'f , , r Web welded- @ _, 1[]0000[]1

I gggg0ii

©

1· •

PLAN ~~, … C2of_

f" • 3j

II Bars notched

for i" • I" cross bars~

-- 1• _ ... 4

,n

-!f • Ii" Bar welded

to angle - 4 sides

l;f t====1r. ,2 ..

-3 Courses of brick

19"

SECTION A-A

SECTION A-A

Welded Steel Grate CD

I 9f Grate S1ze

17 l" lnlel Ooen1ng

C

©

~ Anchor bolt

i• I 12"

~ Anchor bolt -

() 0

sr • 3f' • f Irregular T frame.:.

PLAN

_{__

Grode --------;:;I l

"' ~~~~~~..i..-~~~~---~

, 3 Courses

of brick

f • 12" t Anchor bolt

18" ,, - 1 __

SECTION 8-8

Cast Iron Grote ®

SECTION 8-8

NOTES

1 Inlet grating and frame to withstand a.rcroft wheel loads of largest a,rcraf1 to use the facility

E ~, ,------, :J .---, ..

. ti:;=.'<:::=== . t==, i

2 _Details, dtmenSIO<ls,ond styles of grntes and frames do not represent those

available from any manufacturer.

Select10n of grates and frames wil I

depend on needs for capoci1y,

strength,onchor1ng ,ond single or

multiple grates. © '6",3f·r

Irregular

T frame

a,

SECTION C-C

SECTION C-C

Cast Iron Inlet Grate @

Examples Of Typical Inlet Grates

FIGeRE 21. Examples of typical inlet grates.

Chap 3 Par 10

Page 32

• ,. A l·

•

L 2·-11· PLAN

21¥;

C

.--- 8 ! !+ LI

I ·ij

<I • _J •ID <I

.1 z : 0.:., 0 ~- ~ ~ 0 'fi ... ;+t: Ul ~1·

I

Pave

~·, Reinforcir,q bars 12· o.c. for depths 3' to e·; Ye" ji( Bors 12· o.c. for depths e' to 17.'

..

..

~o~,~~o ; ; II • ~ 8BBBBB Grale not

1\I ! ·.·Jc. <= 000000 shown g -= . 000000 • . L

gggggg ~~ l 'l=J!.;;;O~D~O~D~D;,;:D~===;;=~~=(

• II: ; Ii ;

• ~. • '·. ' • • : • • • • : #

Fin. G.L

a•

..._~ •)

PLAN

3'-6" •,:

~I

·.~·4&:::S?.f~ff;

SECTION C-C

Two-Grote Inlet Structure

~·, Reinforcinq bors 12· o.c. for depths 3' to 8'; Jte"; Bors 12• o.c. for depths 8' to 17'.

AC 150/5320-58

a, p' ""

Grate not Grate not ~~~~~~~ shown sllown

~~~~~~~ .. ""

PLAN

5'- 3 .,,.

SECTION 8-8 Three-Grote Inlet Structure

SECTION 8-8 Three-Grote Inlet Structure

2'-6"

I i D ~:J ~: -"':

8 J

3 Courses of Brick

SECTION D-D

One -Grote Inlet Structure !!Q!ll.:

Oetails dimensions, ond materials for

inlets os well as for ~rates and frames ore illustrative only.

Examples of Inlet Design

FIGURE 22. Examples of inlet design.

SECTION D-D

Par 10 Chap 3

AC 150/5320-SB

1

Length 4 D

1

I I t---------------4 I I L..-------------...J

ELEVATION

ELEVATION

Diam C.Y Cone A B of P,pe Headwall

I. 7 5°-6° 2.24 6°-0· 288 1~0·

3.59 7~6"

C D

12" PIPE C.Y•0.4

E F G

18" PIPE C-Y•0.75

20·

24" PIPE C.'r'.• 1.47

SECTION

PLAN OF APRON SHOWING BAFrLES

FOR 30" PIPE

FOR 30" PIPE

NOTES

Page 33

I. Reinforcing material may be installed

in headwalls whene~r necessary

Z. Baffles may be installed in headwall

aprons to break up excess velocity of water.

Suggested Types of Headwalls

FIGURE 23. Suggested types of headwalls.

Chop 3 Par 10

Page 34

C :i 0 i<,

Woll Stct,on

TYPE A

"'

AC 150/5320-SB

I . ' <t, -'I

<t! " '

Roof Slob

PLAN

Bolt

1 !~ HC?,r1t 8 Vert i - 12 oc .. ~ ;. ! - No1e- The Radius Of The

~ j ~ ,,, Rounded E ntronce Should

1 .-. Be From 11! To 1/7 The

SECTION A-A

SECTION A-A

\

;)

01ome1er Of The Pipe

Approl Wt Grote 280 Lbs Appro1 E f ft ct 1111 Grote Qpenino- 12 5 Sq In Approa; WI Fraine 260 Lbs

HALF PLAN

L

~ 0 ! >

MIiied Hor,zontol F,tt,no Surfaces

Ribs - .!,,,." X 3 \"

SECTION

CAST IRON M.H. GRATES FRAME

.

~ ·~ >

Appro1. Wt Cover 325 Lbs Approx Wt frome 260 Lbs

HALF PLAN

HALF PLAN

Tt11c1i.n111 Of Cower 2~

SECTION

CAST IRON M.H. COVER S FRAME

-'-- '--"--=-----=-~'--.::__..:..C"'-.., … J dimensions of M.H. frames ond grotes are illustrative

not intended to represent those of ony monufocturer TYPE C SECTION C- C

Suggested Manhole Design

FIGURE 24. Suggested manhole design.

CAST IRON M.H. COVER S FRAME

Par 10 Chap 3

AC 150/5320-58

Chap 3

s'-o"

… , .. -...., ..

~~~~~~~m ~~~00~~00

CD

1 --- II -i … 2" TYPICAL PLAN OF DOUBLE INLET GRATING

WATERWAY OPENING= 5.0 SQ. FT. (DOUBLE GRATING)

ASSUME GRATING IS PLACED SO THAT FLOW WILL OCCUR FROM ALL SIDES OF INLET. FOR LOW HEADS DISCHARGE WILL CONFORM WITH GENERAL WEIR EQUATION.

WATERWAY OPENING= 5.0 SQ. FT. (DOUBLE GRATING)

Q= CLH 3/z WHERE

C= 3.0 L= 13.0 FT.GROSS PERIMETER OF GRATE OPENING (OMITTING BARS l FOR GRATE ILLUSTRATED

H = HEAD IN FEET FOR HIGH HEADS DISCHARGE WILL CONFORM WITH ORIFICE FORMULA:

Q=CA~ WHERE

C= 0.6 A=50SQ FT.

g: ACCELERATION OF GRAVITY IN FEET PER SECOND

2

H• HEAD IN FEET THEORETICAL DISCHARGE RELATION TO BE MODIFIED BY 1.25 SAFETY FACTOR COEFFICIENTS BASED ON MODEL TEST OF Sltl.lLAR GRATES WITH RATIO:

NET WIDTH OF GRATE OPENING TO GROSS WIDTH= 2:3

NET WIDTH OF GRATE OPENING TO GROSS WIDTH= 2:3

16 ~-~-~---.-- … ---,------,,---,

10 20

DISCHARGE IN C.FS.

30 40

DETERMINATION OF TYPICAL INLET

GRATING DISCHARGE CURVE

FIGl.RE 25. Determination of typical inlet grating discharge curve.

Page 35

Par 10

Page 36 AC 150/5320-58

Maximum takeoff Tire pressure

GRATING DISCHARGE CURVE

(p.s.i.) Aircraft type weight (lb.) Gear type

Martin 202,404; F-27, FH-227; Convairs 39,900 to 53,200 60 to 95

75 to 120 95 to 168 124

Dual

Dual Dual

240,340,440 Viscount; BAC-111; DC-4 … --------- -- _ 64,500 to 87,000

Constellations; DC-9; B-737; DC-7; B-727 … 90,700 to 170,000 Caravelle … 110,200 Dual tandem Dual tandem Dual tandem Dual tandem DC-lO=Dual

Convair 880,990; B-720, B-707 … - _ - _ _ 184,500 to 312,000 120 to 172 148 to 168 189 170to175

DC-8 … ---------- … ------ --- 273,000 to 355,000 Concorde … - ___ - ___ - - - - - - - 367,000 DC-10; L-1011 ------------------------------ 411,000 to 518,000 tandem +2 L-lOll=Dual tandem 12 Wheel B-SST … 7 50, 000 B-7 4 7; L-500 … - __ \ 713, 000 to 861, 500

220

Future heavy aircraft -------------------------11,500,000

185 to 210 250 Dual, dual tandem (See App. 2 of

AC 150/5320-6A)

Grates and frames for Utility and Basic Transport airports may be those used by the municipality or for highway loadings. Those for other airports should be selected to accept aircraft then using or expected to use the air-

port in the future.

Some manufacturers of grates and frames produce types specifically designed for airport loadings such as 100, 150, 200, and 250 p.s.i.

Hold-down bolts, hooks, or other devices should be provided for the grates to prevent displacement by traffic. The engineer should specify the design load to be carried by the grates and frames and require the vendor to certify that the items furnished have that capacity.

e. The inlet structures may be constructed of reinforced concrete, brick, concrete block,

precast concrete, or rubble masonry. They should be strong enough to withstand the Joads to which they will be subjected.

f. Catch basins for airport drainage are not usually considered necessary particularly when drainage lines are laid on self-cleaning grades. Under certain conditions, catch basins are needed to prevent solids and debris from washing into the system. They should be cleaned out frequently and im·olrn an additional maintenance problem.

g. Manholes are more or less standardized as to type and can be round, m·al, square, or

Par 10

rectangular design. They are usually made of reinforced concrete, brick, concrete block, precast concrete, corrugated metal, or precast pipe sections (Figure 24). The design will depend on the stresses to which they will be subjected. Adequate unobstructed space must be provided within the manhole to enable workmen to clean out the line when necessary. Inside barrel dimensions equivalent to a diameter of 3-% feet and a height of 4 feet are usually considered sufficient, but they can be varied to suit par-

ticular situations.

h. A gutter is not permissible along a runway or a taxiway as it could be hazardous to aircraft operations and would interrupt the runoff which should flow unobstructed transversely off the pavement and across the safety area to the field inlets. In wide apron areas, the inlets should be placed in the valley of the pavement at proper intervals to collect runoff.

i. Inlets in paved areas frequently cause trouble due to differential settlement of the

drainage structure and the adjacent pavement. The resulting depressions around the inlets may result in pavement failure through softening of the subgrade. Particular care in compaction of backfill around inlets will prevent settlement. In rigid parement, the structure is normally protected by expansion joints plaeed around the inlet frame. Also, construction

Chap 3

AC 150/5320-58

joints are installed at a distance from the structure which either matches or is equal to the normal spacing for joints. The slab thus formed around the structure should include steel reinforcement to prevent cracking outward from each corner of the inlet.

j. The number and capacity of grates selected will be dictated by the quantity of runoff to be handled as well as by the depth of head at the grate. In low head situations, capacity (discharge) of the grate(s) will conform to the general weir formula, while in higher head situations the orifice formula is applicable. These formulas and the transition between them are described in Figure 25.

Medium or high head ponding will be unacceptable to personnel sen·icing aircraft with baggage, fuel, food, etc. Morem·er, such ponding could obscure pavement markings and thus inhibit parking of aircraft at gate positions. In some cases, flooding of refueling pits would occur. Although inlets should be located beyond gate positions, controlling elerntions and apron configuration may result in location of inlets fairly close to the field side of the airplane. For these reasons, the weir formula and low head is appropriate for use at some locations.

In general, aprons sen·ing instrument or all weather air carrier operations warrant a head limitation of 0.4 feet. Also, airports where continuing operations are regularly conducted in severe weather conditions would warrant use of a similar limitation. This presumes that apron widths and configurations at other locations will allow runoff to flow directly to turfed areas or that the comparatfrely light traffic in severe weather conditions could adapt to deeper ponding. It is recommended that apron areas drain away from buildings, whene,·er possible.

The orifice formula portion of Figure 25 is applicable to grates in turfed areas, except for the unique case where ponding must be severely limited, such as small turfed areas between aprons and closeby taxiways. The safety factor of 1.25 mentioned in the diag-ram in Figure 25 is intended for use in paved areas. That factor should be increased to 1.5

Chap 3

Page 37

to 2.0 for grates in turfed areas to compensate for grass cuttings. Replacement of drainage lines or structures in or under pavement would be expensive and would disrupt traffic, therefore, the drainage system should be designed with a capacity sufficient for the ultimate pavement configuration. Terminal apron drainage design should be coordinated with

those responsible for the fueling methods and systems to be employed, as well as with those responsible for fire and rescue services.

In large paved areas, such as aprons, sometimes it is feasible to design several segments of the system without ridges between adjacent inlets, thus avoiding grade changes and attendant inhibitions to traffic. In these cases, the efficiency of the grate and its placement should be considered. For such efficiency, all rectangular bars should be parallel with the flow and the openings should cover at least 50 percent of the width of the grate. Multiple grates should be placed normal to the direction of the flow.

11. CULVERTS.

A drainage culvert is designed as a structure ( other than a bridge) to com·ey water through or under a roadway, runway, taxiway, or other obstruction. The choice of circular, oval, elliptical, arch, or box cross section and single or multiple installation will depend on capacity, headroom, economy and occasionally be dictated by local rules or requirements.

The development of a new airport site, or the interruption of natural stream channels by airport facilities, or the increase in runoff caused by airport development may require the design of culverts or consideration of the capacity of existing culverts. In some cases, the airport storm sewer system will need to accept off-site runoff and culverts under roads on the airport perimeter could indicate the

volume of runoff to be accommodated.

Local highway departments or drainage districts normally have jurisdiction over design

and construction of culverts and channels. Indeed, such governmental units may insist on use of certain design criteria. Accordingly, proposed modification or improwment of

Par 10

Page 38

drainage facilities under roadways or off-site, should be reviewed and approved by the re-

sponsible gm·ernment agency.

The objecti,·e in the design of an economical culrnrt is to provide a waterway opening adequate for the passage of floods, and selection of a culvert meeting that objecfo·e is based on the cu!Yert's hydraulic capacity and

site conditions.

Many formulas have been developed over the years to estimate runoff/flood discharge and to determine the size of a culvert. The magnitude of the design flood is a function of its frequency, therefore, it is important to use the appropriate frequencf

Because of the potential risk to adjacent property and to automobile traffic, the design flood frequency used for cuh-erts under roads is for a greater recurrence interrnl than that used for airport storm sewer systems. The local highway department or drainage district may establish the flood frequency to be used: common practice is to design cuh·erts for minor roads for 10- to 25-year flood frequency and for major highways for a recurrence m-

terrnl of 50 years or more.

The rate of discharge or flow through a cuh·ert involves either of two major types of cuh-ert flow; ( 1) flow with inlet control or

(2) flow with outlet control. Under inlet control, the cross sectional area of the culrnrt, the inlet geometry, and the amount of headwater or ponding at the entrance are of primary importance. Outlet control inrnh·es the additional consideration of the elerntion of the taihrnter in the outlet channel and the slope, roughness, and length of the cuh·ert barrel.

Par 11

AC 150/5320-58

Field inspection and evaluation of downstream controls or obstructions would indicate the potential depth of tailwater and thus indicate when outlet control will be applicable. Usually channels are wide as compared to the cuh·ert and the depth of water in the channel is considerably less than critical depth and thus inlet control is applicable.

It has been demonstrated that the capacity of a culvert in inlet control can be increased by providing a rounded, bernlled, or tapered entrance. In other words, the capacity of a thin edge projecting metal pipe can be enhanced by the addition of an attachment or the building of a rounded, berelled, or tapered entrance into a headwall. Similarly, the capacity of other types of pipe or box culrerts can be increased at little cost by incorporating a beYel into the headwall.

The procedure for selection of the culwrt size and t)·pe for most design conditions is

well covered in several publications. These publications include charts or nomographs allowingcomparison of the capacities of rnrious types and sizes of culrerts, therefore, the most economical choice will be apparent.

Current issues of sernral, widely used publications are listed in the bibliography as references 9, 14, 15, 17, 18, 21, and 24.

ObYiously, the foregoing is not intended to be a complete treatment of culrnrt design, but is included to emphasize some of the fundamentals and to recognize that the airport designer may need to consider and include cuh-erts in the total design.

Chap 3

AC 150 / 5320-58 Pag<> 39

Chapter 4. GRADING CRITERIA

Chapter 4. GRADING CRITERIA

12. SELECTIVE GRADING.

a. In developing an airport, proper grading is the most important single factor con-

tributing to the success of the drainage system. Grading and drainage plans should be most careful1y coordinated. Cross sections for runways and taxiways should be developed with sloping shoulders so that the surface water is directed a,rny from the pavements and into areas for collection and disposal. The life of the pavements and the functions of drainage can generally be improved by selecti,·e grading.

b. Before grading activities are started, the engineer should haw complete soil test data of the different soils encountered on the site and data on materials from any borrmv sources. As determined from the soil profile and the soil characteristics, the best types of arnilable excarnted materials should be so selected and placed to form the strongest and most drainable soil structures beneath and adjacent to the pa,·ement. The more undesirable soils should be placed in the intermedir.te areas as far remowd from the pavements as possible.

c. Gradient desi~1 standards are found in:

11 l AC' 150/5300-2A, Airport Design Standards-Site Requirements for Terminal X a vigational Facilities.

121 AC 150/5300-4A, Utility Airports,

(3) AC 150/5325-2B, Airport Design Standards-Air Carrier Airports-Surface Gradient and Line of Sight.

13. SOIL CONDITIONS.

a. "Then the soil surrny discloses different types and strata of soils on the site, different methods and procedures in the grading and drainage construction should be considered. In grading, fills are made of the material obtained from cuts and other excavation. There-

Chap 4

fore, a basis of design is an understanding of the nature of the soils that will be encountered.

n l On sites where the soils are of a good pen·ious type and are drainable, the drainage problem is greatly simplified. This type of soil is . generally the contributing factor for natural drainage. The major consideration. of such a site is to determine whether an im-

pervious strata, which might pocket the water as it percolates downward, underlies the

pervious surface soils. If so, prm·isions must be made to remove the trapped water. Usually, though, the only consideration necessary is proper grading of the area to prm-ide for surface runoff. The slope of the graded areas must be carefully controlled because such soils may tend to erode.

(2) Sites with impenious soils are a different drainage problem. By their natnre. very little precipitation will infiltrate into impervious soil. In such cases, there is little need for any subsurface drainage. Surface drainage is required, howernr, and will han~ to be designed to take care of the estimated runoff. Some impervious soils are also subject to erosion, and this characteristic should he considered.

Some clay type soils may gfre the appearance of being impervious, but they actuaUy allow a very high capillary rise from the water table, which can saturate the subbase or base course. In such cases, subsurface drains at the pavement edge will help keep the subbase or base dry.

(3) At sites where pervious soils are superimposed on impervious soils, tests should

be made to determine the extent and the profile of the top of the underlying layer. Some sur-

face drainage will be needed and may be pro- ,-ided by proper grading with occasional inlets in the low areas, but some system of sub-

Par 12:

.,, !? - w

n :r Q ,, ...

*1s.s' Edge of Surface * DIMENSIONS WILL VARY WITH DEPTH OF PAVEMENT COURSES.

C 'iiJ G'·, 0,:/0 •. 0:-:00 11 ~· o .... o . . . . o·.O· 4 ~Ubbose C) ·o ·: o;..O·o 0 :o.,_ 0 w., ... 0 Q ;,;i~Oc

*~I.~:& .~ ... ,.-:r-·':: ,~ 10 P.C:

to .4

*36'

** GRADE MAY VARY WITH AIRPORT CATEGORY.

Impervious Material (Topsoil)

Cone. ·~r//// r--._ t • u · ( · ) ~:.i>"::f·./ / / .r-,...L_ ,,r Impervious material Topsoil

<I ·o:. . --'" 0 ~ .. o '-'.o.·.<;J,.~:f.tj::~:j';o .·~ "/. / /'"'-, … ),: r,3 to ,4 ·9· ·." ·o … o ·:Vo .. ·~//~ . ~.6 ~0 -.. ~.- S~bbose·Q·o·:·0 ·,:j o-.~

o q ·. ·O ~- :,f9_'.~·-. o-~ ~·.v :<::> (Jo t:;;·;.·

Example of Widened Subbase Sections for Extreme Snow Conditions

Frnum: 2G. Flxarnple of widened suhhasP sectiom; for extreme snow con!litlons.

.,, Q co …

0

,. n - u, 0 - u, w ... ? u, "'

AC 150/5320-SB

drainage is definitely required to remove the

water from the top of the impen·ious layer. If the laver is not too far below the surface, the subd;ainage pipe trenches should extend slightly into the impen-ious layer (approxi-

mately 6 inches) and be backfilled with a granular material. The granular backfill material should be placed around and adjacent to the pipe.

(4) There are cases where an airport will be located on a site in which an imper,·ious layer of soil is on the surface, with a per,·ious st~atum below. Surface drainage will always be needed for draining such a site, and the

svstem should be designed to remorn all of the e~timated runoff. Again, a thorough understanding of the types and extent of the soil

with their respectiYe profiles will be needed because grading operations may open up or pocket the underlying porous stratum. The underlying porous stratum often introduces underground water onto a site, requiring intercepting ditches along the edges of the airport or an intercepting drain line to cut off and diYert this flow. Surface runoff sometimes maY be directed into the porous layer, if it is ext~nsi,·e enough, by tapping through the top impen·ious layer with proper structures, and allowing the surface water to enter the porous layer.

(5) Drainage engineers frequently find the situation in which there are irregular strata of pen-ious and imperrious materials.

The most important thing in this situation is to locate all of the pockets existini;! beneath the surface and to prm·ide sufficient drains to remow the water from them. Drainage from those pockets can be piped directly from the

site or fed into the surface drainal!e system by proper connections. In some cases it may be necessary to remoYe the undesirable material

from th; pockets, especially under and adjacent to the payement, and to backfill "·ith desirable material.

b. In seasonal frost areas it is important to determine the frost penetration, since the drainage pipelines should be placed below this depth whenewr possible. A serious condition could dewlop if the draina::re lines were laid aboye the frost penertation line. The system

Chap 4

Page 41

could become inoperatiw when water freezes

upon contact with the drainpipes. Field de-_ terminations of frost penetration show that the depth of penetration for various soils are fairly consistent for the same location.

(1) In granular soils, frost enters the ground quicker, penetrates deeper at an earlier stage, and leaves the ground more rapidly in the spring than in a tighter clay soil. In a clay soil the frost gradually leaYes in the early spring from both the top and the bottom of the frozen stratum. It finally tha""s out at a point somewhere near the midsection between the ground surface and the point of deepest

penetration. During this thawini;!-out period, the soil becomes saturated and Yery unstable.

(2) Frost heaving may also occur and cause damage to the drainage system. Frost heaving is the result of freezing of capillary moisture that cannot be remored by drainage from certain soils of a silty or silty sand texture. The best way to eliminate frost heave is to remorn the unfayorable soil to a sufficient depth and to replace it with a suitable material not subject to frost heave. In some localities, low temperatures and snowfalls result in deep frost penertation and deep accumulations of sno"" on the parnment shoulder areas and adjacent thereto. As a consequence. the thaw period is prolonged and may result in saturation of the subgrade and instability of the base or subbase.

Installation of edge subdrains is the usual solution, however, it may be found that a widened subbase will be as effeetiYe and of

reasonable cost. The examples of widened subbase sections sho""n in Figure 26 are not intended to be standard, as the dimensions and some of the grades will rnry with the pawment depth and the airport category. This method of subsurface drainage is not advocated for airports unless it has been shown to be practical in the general soil and climatological situation applicable to the site.

14. LOADS ON CONDUITS.

a. In the design and construction of drainage system conduits under pa,·ement, the maximum anticipated wheel loads should re-

Par 13

Page 42 AC 150/5320-58

TABLE III. l\Iinimum depth of eo,er in feet for pipe under flexible pa,ement (Part 1)

CORRUGATED ALUMINUM 2 2/3" 11 /2" or 2" 11 /'l:'

CORRUGATIONS

AIRCRAFT WHEEL LOAD-Up to 30,000 lb. single and up to 40,000

lb. dual

Metal I Pipe diameter (in.) thickness ,

(in.) 12 18 24 36 48 60 72 84 96

I 0.060 … ~ 2.0 I 2.5 I 2.5

I

I 2.513.0 1.5 2.0 2.5 1.5 1.5

0.075 … 1.5 i 2.0 , 2.5 I 0.105 … , 1.5 1.5 3.0 I 0.135 … I I 1.0 1.0 11.5 i 0.165 … I i I i l.O 1.5 1.512.0 12.0

I I

AIRCRAFT WHEEL LOAD-40,000 lb. dual to 110,000 lb. dual

Pipe diameter (m.)

12 18 24 36 48 60 72 84 96

Metal thickness

(in.) … i … ,

i 1 ' 1 1 I i i 0.060 … ' 2.0 2.5 i 2.5 I I i ·1 I i 0.075 … i 1.5 : 2.0 i 2.5 I 2.5 I 3.0 2.5 ', 3.0 1' l 0.105 … : 11.5 I 1.5 i 1.5 i 2.0 j i 0.135 … i I ' ! 1.5 1 1.5 2.0 2.5 1 3.0 i o.16s … ; i 1.5 1.512.0 I 2.0 j 2.5 ,------------------'------- : AIRCRAFT WHEEL LOAD-110,000 lb. dual to 200,000 lb. dual; '190,000 lb. dt. to 350,000 lb. dt; up to 750,000 lb. ddt & 1,500,000 lb I

1 Metal Pipe diameter (in.) ·

1 thickness

I (in.) i 12 18 24 36 48 60 J2 84 96 !-------,-------...,.------,------1 I I I i I I I

1 0.060 … : 3.o : 3.o : 3.o . I , '0.075 … ! 3.0 I 3.0: 3.0 I 3.5 5.0 '1 I I o.1os … ! · 2.0 : 2.0 : 2.5 3.5 4.5 • I : o.m … ! 1 I 2.0 3.o j 4.o I 4.5 1 5.5 i 0.165 … 2.5 , 3.5 I 4.0 : 5.0 ! 5.5

l CLAY :--~- I : AIRCRAFT WHEEL LOAD-up to 30,000 lb. single and up to 40,000 I • lb. dual

1 I Pipe diameter (in.) ! Pipe type I I i I 6 10 12 15 18 21 24 30 36 i &~re-i I I I I I I I I clay … ! 2.0 ! 2.5 12.5 i 2.5 l 2.5 . 2.5 1 2.5 2.5 1 2.5

Extra ! I I j I I I I strength clay! 2.0 \ 2.0 i 2.0 l 2.0 12.0 2.0 . 2.0 2.0 2.0

AIRCRAFT WHEEL LOAD-40,000 lb. dual to 110,000 lb. dual

I I Pipe diameter (in.) I I I

Pipe type i

10 12 15 18 21 24 30 36 I 6 ! Std. strength; , ; l ! 1 ! \ : clay … 1 4.0 , 5.5

1 6.0 , 6.0 ! 6.0 I 6.0 6.0 ; 6.0 6.0 I I Extra !-i--:--!--:--,----·---- i stren h cla ' 2.0 i 3.5 : 3.5 ! 3.5 : 3.5 I 3.5 3.5 3.5 5 gt y

I

Par 14

CORRUGATED ALUMINUM 6" 11" CORRUGATIONS J

CORRUGATED ALUMINUM 6" 11" CORRUGATIONS J

AIRCRAFT WHEEL LOAD-up to 30,000 lb. single and up to 40,COO

lb. dual Metal thickness

(in.)

I Pipe diameter (in.)

36 48 60 72 84 96 108 120

0.060 … 2.0 / 2.0 I 2.5 3.o I i \ I I 0.075 … 1.0 I 1.512.0 2.5 3.5 I : I I 0.105 … 1.0 II 1.0 1.5 2.0 , 3.0 13.5 1' ,·. I 0.135 … 1.5 2.0 2.5 3.o 4.o , I 0.165 … I I I 2.0 12.5 13.5 I 4.5

AIRCRAFT WHEEL LOAD-40,000 lb. dual to 110,000 lb. dual

Metal thickness

(m.)

Pipe diameter (m.)

36 48 60 12 s4 96 108 120 I 1-------,---,-----------' I I ' I i I i I I 0.060 … , 2.5 I 3.0 I 3.5 4.0 I I ·1 : o.075 … J 1.5 ! 2.0 i 2.5 , 3.o

1 4.o i I I 0.105 … 1.5 11.5 2.0 2.5 I 3.5 I 4.0 I I 0.135 … 1 ! 2.0 2.5 ! 3.0 3.5; 4.5: I

I

0.165_, … I 12.5 l 3.0 ! 4.0: 5.0 I

I , I

1 AIRCRAFT WHEEL LOAD-110,000 lb. d. to 200,000 lb. d; 190,000 lb. dt. to 350,000 lb. dt.; up to 750,000 lb. ddt. & 1,500,000 lb.

Metal ! Pipe diameter (in.) thickness ,------------- (in.) ! 36 48 60 72 84 96 108 120 ; , I ! I I : i i 0.060 … 4.0 4.5 I 5.0 i 5.0 ! 0.075 … 1 3.0 3.5 ' 3.5 14.0

0.105 … ( 2.0 2.0 3.0 I 2.5 0.135 … 1 2.5 i 3.0 0.165 … : I

4.0 : 1 4.0 ! 4.5 : . 3.5.4.015.0; I 3.o : 3.5 . 4.5 , 5.5 I

I ASBESTOS CEMENT I

I

AIRCRAFT WHEEL LOAD-up to 30,000 lb. single and up to 40,000 ;

lb. dual [

I

Asbestos : Pipe diameter (in.) I cement- l:--------------

class J 6 10 12 16 18 24 30 36 42 I

1500 … , 2.5 i 2.5 ! 2.5 1 2.5 i 1 : I i I 2400 … 1 2.5 I 2.5 i 2.5 I 2.512.512.5 I I I I 3300 … , l.5 1.5 i 1.5 i 1.5 1.5 1.511.5 I II 4000 … l.5

I ASBESTOS CEMENT I

1

1 1.5 I 1.5 11.5 1.5 1.5 1.5 , 5000 … 1. 1.5 1.5 j 1.5 1.5 I 1.5 11.5 ,

1

. 1.5 j 1.5 , 6000 … , II I J 1.0 ; 1.0 1 7000 … 1 i : I 1.0 I 1.0 1 I AIRCRAFT WHEEL LOAD-40,000 lb. dual to 110,000 lb. dual

Pipe diameter (in.) Asbestos

1 cement- ,--------------- class 6 10 12 16 18 24 30 36 42

1500 … 5.5 I 5.5 1 5.5 5.5 i 6.0 I . I 2400 … , 6.o

1

, 6.o 6.o 6.o 1 6.o 3300 … : 3.5 3.5 3.5 3.5 3.5 3.5 4000 … 1 3.5 3.5 3.5 , 3.5 3.5 5000 … ! I 3.5 3.5 3.5 3.5 3.5 6000 … : 7000 …

3.5 I 3.5 : : 3.51' 3.51' 3.5 : 2.5 2.5 , , 2.5 i 2.5 :

Chap 4

AC 150/5320-SB Page 43

'l'.\BLE III.-:\Iinimnm depth of cover in feet for pipe under flexible pavement (Part 2)

CORRUGATED STEEL 2 2/3" x 1 /2" CORRUGATIONS

CORRUGATED STEEL 2 2/3" x 1 /2" CORRUGATIONS

AIRCRAFT WHEEL LOAD-Up to 30,000 lb. single and up to

1

' … 4_0._oo~O~lb_.~d-ua_1 …

Metal Pipe diameter (in.)

I

thickness

(in.) 12 18 24 36 48 60 72 84 96

I I I : . : I 0.05L .... 1 1.0 I 1.0 1.5 ! 1.5 : i 0.064 … , 1.0 , 1.0 1.0 · 1.5 I 1.5 : 0.079 … 1 1.0 ' 1.0 1.0 1· 1.5 I 1.5 I 1.5 ' I I 1.5 : I I

I

o.10L .... 1 I 1.0 1.0 . 1.0 : 1.0 0.138 … I 1.0 , 1.0 1.0 I 0.168 … i I 1 1.0, 1.0: 1.0 I ! : .

1.0 I 1.5 ' 1.0 i 1.511.5

AIRCRAFT WHEEL LOAD-40,000 lb. dual to 110,000 lb. dual

Metal Pipe dian,eter (in.) thickness

(in.) 12 18 24 36 48 60 72 84 96 i ,---~.------------

1 : i ! ' t 0.052 … : 1.5 • 2.0 , 2.0 : 2.5 i 0.064 … 1 1.5 : 1.5 I 2.0 i 2.5: 2.5

I

I 0.07L .... ! 1.5 ! 1.5 , 2.0 ! 2.5 :. 2.5, 2.5

0.109 … I 1.5 , 2.0 , 2.0 , 2.0 0.138 … : . 2.0 2.0 2.0 0.168 … , 2.0 , 1.5 2.0 ! I

2.5 , 2.0 1 2.5 ! I 2.0 ' 2.0 ' 2.51

AIRCRAFT WHEEL LOAD-110,000 lb. dual to 200,000 lb. dual;

190,000 lb. dt. to 350,000 lb. dt.; up to 750,000 lb. ddt.

I

Metal Pipe diameter (in.) thickness

(in.) ; 12 18 24 36 48 60 72 84 96

Continue reading ↓ 120 of 240 passages shown