AC 107-2A Small Unmanned Aircraft System (Small UAS)
This AC provides guidance in the areas of airman (remote pilot) certification, aircraft registration and marking, aircraft airworthiness, and the operation of small Unmanned Aircraft Systems (UAS) in the National Airspace System (NAS) to promote compliance with the requirements of Title 14 of the Code of Federal Regulations (14 CFR) part 107.
U.S. Department of Transportation Federal Aviation Administration
Advisory Circular
Subject: Small Unmanned Aircraft System
(Small UAS)
Date: 2/1/21 AC No: 107-2A Initiated by: AFS-800 Change:
This advisory circular (AC) provides guidance for conducting small unmanned aircraft systems (UAS) operations in the National Airspace System (NAS) in accordance with Title 14 of the Code of Federal Regulations (14 CFR) part 107.
Robert C. Carty Deputy Executive Director, Flight Standards Service
ii
CONTENTS Paragraph Page
Chapter 1. General … 1-1
1.1 Purpose of This Advisory Circular (AC) … 1-1
1.2 Where You Can Find This AC … 1-1
1.3 What This AC Cancels … 1-1
1.4 Request for Information … 1-1
1.5 AC Feedback Form … 1-2
Chapter 2. References … 2-1
2.1 Related Code of Federal Regulations (CFR) Parts … 2-1
2.2 Notices to Air Missions (NOTAM) … 2-1
2.3 Related Reading Material … 2-1
Chapter 3. Background … 3-1
3.1 PL 112-95, Title III, Subtitle B … 3-1
3.2 Organization of Part 107 … 3-1
Chapter 4. Part 107 Subpart A, General … 4-1
4.1 Applicability … 4-1
4.2 Definitions … 4-1
4.3 Falsification, Reproduction, or Alteration … 4-5
4.4 Accident Reporting … 4-5
Chapter 5. Part 107 Subpart B, Operating Rules (Small UAS) … 5-1
5.1 Applicability … 5-1
5.2 Aircraft Operation … 5-1
5.3 Aeronautical Decision-Making (ADM) and Crew Resource Management (CRM) … 5-2
5.4 Aircraft Registration … 5-2
5.5 Small Unmanned Aircraft Maintenance, Inspections, and Condition for Safe Operation … 5-3
5.6 Medical Condition … 5-3
5.7 Civil Twilight and Operations at Night … 5-4
5.8 Operations Over Open-Air Assemblies of Persons … 5-5
5.9 VLOS Aircraft Operation … 5-5
iii
5.10 Operation Near Airports, in Certain Airspace, in Prohibited or Restricted Areas, or in the Proximity of Certain Areas Designated by a Notice to Air Missions (NOTAM) … 5-7
5.11 Preflight Familiarization, Inspection, and Actions for Aircraft Operation … 5-9
5.12 Operating Limitations for Small Unmanned Aircraft … 5-11
5.13 Remaining Clear of Other Aircraft … 5-12
5.14 Operations from Moving Vehicles … 5-12
5.15 Transportation of Property … 5-13
5.16 Operations While Impaired … 5-13
5.17 Remote Identification of Unmanned Aircraft Systems … 5-14
5.18 In-Flight Emergency … 5-15
5.19 Careless or Reckless Operation … 5-15
5.20 Certificate of Waiver … 5-15
5.21 Supplemental Operational Information … 5-16
Chapter 6. Part 107 Subpart C, Remote Pilot Certification … 6-1
6.1 Applicability … 6-1
6.2 Remote Pilot Certification … 6-1
6.3 Eligibility … 6-1
6.4 Application Process … 6-1
6.5 Security Disqualification … 6-4
6.6 FAA Tracking Number (FTN) Requirement … 6-4
6.7 Aeronautical Knowledge Test … 6-4
6.8 Aeronautical Knowledge Training … 6-6
Chapter 7. Small UAS Maintenance and Inspection … 7-1
7.1 Applicability … 7-1
7.2 Maintenance … 7-1
7.3 Preflight Inspection … 7-2
Chapter 8. Small Unmanned Aircraft Over People … 8-1
8.1 Applicability … 8-1
8.2 Category of Operations … 8-1
8.3 Operations Over People … 8-1
8.4 Applicant … 8-10
iv
8.5 Means of Compliance—General Information … 8-12
8.6 FAA-Provided MOC … 8-13
8.7 Voluntary Consensus Standards Body MOC … 8-18
8.8 Means of Compliance … 8-19
8.9 Declarations of Compliance … 8-20
8.10 Accountability for Holders of DOCs … 8-24
8.11 Product Labeling … 8-29
8.12 Remote Pilot Operating Instructions … 8-30
8.13 Remote Pilot Responsibilities When Conducting Operations Over People … 8-36
8.14 Operations Over People at Night … 8-36
Appendix A. Risk Assessment Tools … A-1
Appendix B. Supplemental Operational Information … B-1
Appendix C. Small UAS Maintenance and Inspection Best Practices … C-1
Appendix D. Remote Pilot Certification and Applicant Identity Verification … D-1
Appendix E. Sample Preflight Assessment and Inspection Checklist … E-1
List of Figures
Figure 4-1. FAA Regional Operations Centers Telephone List … 4-6
Figure 6-1. Recurrent Training Cycle Examples … 6-6
Figure 8-1. Requirement to Submit a DOC for a Modified Small Unmanned Aircraft … 8-12
Figure 8-2. Sample Remote Pilot Operating Instructions … 8-33
Figure A-1. Hazard Identification and Risk Assessment Process Chart … A-3
Figure A-2. Sample Safety Risk Assessment and Mitigation Steps Before Flight … A-4
List of Tables
Table 4-1. Abbreviations/Acronyms Used in This AC … 4-3
Table 8-1. Operations Over Moving Vehicles – Over or Within a Closed/Restricted Access Site … 8-3
Table 8-2. Operations Over Moving Vehicles – Not Over or Within a Closed/Restricted Access Site … 8-3
Table 8-3. Operations Over People – Over or Within a Closed/Restricted Access Site … 8-9
Table 8-4. Operations Over People – Not Over or Within a Closed/Restricted Access Site … 8-10
Table 8-5. Maximum Impact Speeds (ft/sec) for a Given Weight and Impact Kinetic Energy Under FAA-Provided MOC … 8-16
v
Table 8-6. Maximum Impact Speeds (mph) for a Given Weight and Impact Kinetic Energy Under FAA-Provided MOC … 8-16
Table C-1. Small UAS Condition Chart … C-1
1.4 Request for Information. › Washington, DC 20003
CHAPTER 1. GENERAL
1.1 Purpose of This Advisory Circular (AC). This AC provides guidance in the areas of airman (remote pilot) certification, aircraft registration and marking, aircraft airworthiness, and the operation of small Unmanned Aircraft Systems (UAS) in the National Airspace System (NAS) to promote compliance with the requirements of Title 14 of the Code of Federal Regulations (14 CFR) part 107.
1.1.1 Effects of Guidance. The contents of this document do not have the force and effect of law and are not meant to bind the public in any way. This document is intended only to provide clarity to the public regarding existing requirements under the law or agency policies. It does not provide, nor is it intended to provide, a legal interpretation of the regulations. This AC uses mandatory terms, such as “must,” when the language is describing an established statutory or regulatory requirement. This AC does not change, add to, or delete regulatory requirements or authorize deviations from regulatory requirements or restrictions.
1.1.2 Part 107 Provisions. This AC is not intended to cover every provision of part 107. Rather, this AC is intended to provide guidance on those provisions of part 107 where additional information may be helpful. The Federal Aviation Administration (FAA) emphasizes, however, that persons subject to part 107 are responsible for complying with every applicable provision of part 107, regardless of whether the provision is discussed in this AC.
1.1.3 Privacy-Related Laws. Part 107 operators should be aware that State and local authorities may enact privacy-related laws specific to UAS operations. The FAA encourages small UAS operators to review those laws prior to operating their UAS. The National Telecommunications and Information Administration (NTIA) has also published the Voluntary Best Practices for UAS Privacy, Transparency, and Accountability (dated May 18, 2016), available at https://www.ntia.doc.gov/files/ntia/publications/uas_privacy_ best_practices_6-21-16.pdf. This document outlines and describes voluntary best practices that small UAS operators could take to advance UAS privacy, transparency, and accountability for the private and commercial use of UAS.
1.2 Where You Can Find This AC. You can find this AC on the FAA’s website at https://www.faa.gov/regulations_policies/advisory_circulars.
1.3 What This AC Cancels. AC 107-2, Small Unmanned Aircraft Systems (sUAS), dated June 21, 2016, is canceled.
1.4 Request for Information. Direct comments and suggestions for improving this publication to:
Federal Aviation Administration General Aviation and Commercial Division (AFS-800)
55 M Street SE, 8th Floor, Zone 1 Washington, DC 20003
1.5 AC Feedback Form. For your convenience, the AC Feedback Form is the last page of this AC. Note any deficiencies found, clarifications needed, or suggested improvements regarding the contents of this AC on the Feedback Form.
2.3 Related Reading Material. › 2.3.1 FAA ACs and Directives (current editions).
CHAPTER 2. REFERENCES
2.1 Related Code of Federal Regulations (CFR) Parts. The following regulations and parts can be found at https://www.faa.gov/regulations_policies/faa_regulations/.
2.1.1 Title 14 CFR.
• Part 1, Definitions and Abbreviations.
• Part 43, Maintenance, Preventive Maintenance, Rebuilding, and Alteration.
• Part 47, Aircraft Registration.
• Part 48, Registration and Marking Requirements for Small Unmanned Aircraft.
• Part 71, Designation of Class A, B, C, D, and E Airspace Areas; Air Traffic Service Routes; and Reporting Points.
• Part 73, Special Use Airspace.
• Part 89, Remote Identification of Unmanned Aircraft.
• Part 91, General Operating and Flight Rules.
• Part 93, Special Air Traffic Rules.
• Part 99, Security Control of Air Traffic.
• Part 107, Small Unmanned Aircraft Systems.
2.1.2 Title 47 CFR. Part 87, Aviation Services.
2.1.3 Title 49 CFR. Part 830, Notification and Reporting of Aircraft Accidents or Incidents and Overdue Aircraft, and Preservation of Aircraft Wreckage, Mail, Cargo, and Records.
2.2 Notices to Air Missions (NOTAM). Information on how to obtain NOTAMs can be found at https://pilotweb.nas.faa.gov/PilotWeb/.
2.2.1 Additional resources to create NOTAMs, check weather, and prepare flight plans can be found at https://www.1800wxbrief.com/.
2.3 Related Reading Material. The following listed reference materials contain additional information necessary to ensure safe operations in the NAS. A small UAS operator may want to consider seeking out additional publications to supplement the lists below.
2.3.1 FAA ACs and Directives (current editions). You can find the current editions of the following publications on the FAA websites https://www.faa.gov/regulations_policies/advisory_circulars/ and https://www.faa.gov/regulations_policies/orders_notices/.
• AC 00-6, Aviation Weather.
• AC 00-45, Aviation Weather Services.
2.3 Related Reading Material. › 2.3.2 Additional FAA Online/Mobile Sources.
• AC 60-28, FAA English Language Standard for an FAA Certificate Issued Under 14 CFR Parts 61, 63, 65, and 107.
• AC 61-141, Flight Instructors as Certifying Officials for Student Pilot and Remote Pilot Applicants.
• AC 120-92, Safety Management Systems for Aviation Service Providers.
• FAA Order JO 7110.10, Air Traffic Organization Policy, Flight Services.
• FAA Order JO 7110.65, Air Traffic Organization Policy, Air Traffic Control.
• FAA Order JO 7200.23, Air Traffic Organization Policy, Processing of Unmanned Aircraft Systems Requests.
• FAA Order JO 7210.3, Air Traffic Organization Policy, Facility Operation and Administration.
• FAA Order JO 7400.11, Air Traffic Organization Policy, Airspace Designations and Reporting Points.
• FAA Order 8130.34, Airworthiness Certification of Unmanned Aircraft Systems and Optionally Piloted Aircraft.
• FAA Order 8900.1, Volume 16, Unmanned Aircraft Systems.
2.3.2 Additional FAA Online/Mobile Sources.
• UAS website: https://www.faa.gov/uas/.
• UAS Registration website: https://faadronezone.faa.gov/.
• B4UFLY mobile app.
• UAS Flight Planning, NOTAMs, temporary flight restrictions (TFR): https://www.1800wxbrief.com/ and https://tfr.faa.gov.
• FAA Safety website: https://www.faasafety.gov.
• FAA UAS Data Delivery System website: https://udds-faa.opendata.arcgis.com/.
• FAA Waiver Safety Explanation Guidelines for Part 107 Waiver Applications: https://www.faa.gov/uas/commercial_operators/part_107_waivers/waiver_safety_exp lanation_guidelines/.
• FAA Integrated Airman Certification and Rating Application (IACRA): https://iacra.faa.gov/iacra.
• Airman Certificate Testing Service (ACTS): https://www.faa.gov/training_testing/testing/ACTS/.
• Flight Standards District Offices (FSDO): https://www.faa.gov/about/office_org/field_offices/fsdo.
2.3 Related Reading Material. › 2.3.4 Statutory Resources.
2.3.3 FAA Handbooks, Manuals, and Other Publications. You can find the following handbooks, manuals, and other publications on the FAA website at https://www.faa.gov/regulations_policies/handbooks_manuals/.
• Aeronautical Information Manual (AIM): https://www.faa.gov/air_traffic/publications/.
• Aeronautical Charts (Digital): https://www.faa.gov/air_traffic/flight_info/aeronav/digital_products/.
• Pilot/Controller Glossary: https://www.faa.gov/air_traffic/publications/.
• Pilot’s Handbook of Aeronautical Knowledge: https://www.faa.gov/regulations_policies/handbooks_manuals/aviation/phak/.
• Risk Management Handbook: https://www.faa.gov/sites/faa.gov/files/regulations_policies/handbooks_manuals/aviat ion/risk_management_hb_change_1.pdf.
• Remote Pilot – Small Unmanned Aircraft Systems Airman Certification Standards (ACS): https://www.faa.gov/training_testing/testing/acs/media/uas_acs.pdf.
• Unmanned Aircraft Systems Operating Handbook: https://www.faa.gov/about/office_org/headquarters_offices/avs/offices/afx/afs/afs600 /afs630/.
2.3.4 Statutory Resources.
• Public Law (PL) 112-95 (Feb. 14, 2012), Title III, Subtitle B—Unmanned Aircraft Systems.
• PL 114-190 (July 15, 2016), Title II, Subtitle B—UAS Safety.
• PL 115-254 (Oct. 5, 2018), Title III, Subtitle B—Unmanned Aircraft Systems.
CHAPTER 3. BACKGROUND
3.1 PL 112-95, Title III, Subtitle B. In 2012, Congress passed the FAA Modernization and Reform Act of 2012, PL 112-95. Section 333 of PL 112-95 directed the Secretary of Transportation to determine whether UAS operations posing the least amount of public risk and no threat to national security could safely be operated in the NAS and, if so, to establish requirements for the safe operation of these systems in the NAS. As part of its ongoing efforts to integrate UAS operations in the NAS and in accordance with Section 333, in June 2016, the FAA issued a final rule adding part 107, integrating civil small UAS into the NAS. Part 107 allows small UAS operations for many different purposes without requiring airworthiness certification, exemption, or a Certificate of Waiver or Authorization (COA).
CHAPTER 3. BACKGROUND › 3.2 Organization of Part 107.
3.2 Organization of Part 107. The FAA addresses aviation safety in three key areas: personnel, equipment, and operations. The FAA assesses each of these areas both independently to meet current regulations and standards, as well as collectively to ensure no conflicts exist overall that would create an unsafe condition. This approach allows the FAA to be flexible in responding to the needs of the aviation community while still being able to establish standards for future growth and development. To that end, part 107 contains subparts that focus on each of these key aviation safety areas specific to small UAS, and the chapters in this AC are organized in the same manner.
4.2 Definitions. › 4.2.4 Declaration of Compliance (DOC).
CHAPTER 4. PART 107 SUBPART A, GENERAL
4.1 Applicability. This chapter provides guidance regarding the applicability of part 107 to civil small unmanned aircraft operations conducted within the NAS. However, part 107 does not apply to the following:
1. Limited recreational operations of UAS that occur in accordance with Title 49 of the United States Code (49 U.S.C.) § 448091;
2. Operations conducted outside the United States;
3. Amateur rockets;
4. Moored balloons;
5. Unmanned free balloons;
6. Kites;
7. Public aircraft operations; and
8. Air carrier operations.
4.2 Definitions. The following defined terms are used throughout this AC:
4.2.1 Applicant. A person who submits a declaration of compliance (DOC) to the FAA for review and acceptance. An applicant may be anyone who designs, produces, or modifies a small unmanned aircraft.
4.2.2 Control Station (CS). An interface used by the remote pilot or the person manipulating the controls to control the flightpath of the small unmanned aircraft.
4.2.3 Corrective Lenses. Spectacles or contact lenses.
4.2.4 Declaration of Compliance (DOC). A record submitted to the FAA that certifies the small unmanned aircraft conforms to the Category 2 or Category 3 requirements under part 107 subpart D, as described in Chapter 8, Small Unmanned Aircraft Over People.
1 Title 49 U.S.C. § 44809(a) states that a person may operate a small unmanned aircraft without specific certification or operating authority from the FAA if the operation adheres to all of the following limitations: (1) the aircraft is flown strictly for recreational purposes; (2) the aircraft is operated in accordance with or within the programming of a community-based organization’s set of safety guidelines that are developed in coordination with the FAA; (3) the aircraft is flown within Visual Line of Sight (VLOS) of the person operating the aircraft or a visual observer (VO) co-located and in direct communication with the operator; (4) the aircraft is operated in a manner that does not interfere with and gives way to any manned aircraft; (5) in Class B, Class C, or Class D airspace or within the lateral boundaries of the surface area of Class E airspace designated for an airport, the operator obtains prior authorization from the Administrator or designee before operating and complies with all airspace restrictions and prohibitions; (6) in Class G airspace, the aircraft is flown from the surface to not more than 400 feet above ground level (AGL) and complies with all airspace restrictions and prohibitions; (7) the operator has passed an aeronautical knowledge and safety test described in § 44809(g) and maintains proof of test passage to be made available to the Administrator or law enforcement upon request; and (8) the aircraft is registered and marked in accordance with 49 U.S.C. chapter 441 and proof of registration is made available to the Administrator or a designee of the Administrator or law enforcement upon request.
4.2 Definitions. › 4.2.12 Voluntary Consensus Standards Body.
4.2.5 Means of Compliance (MOC). The method an applicant uses to show its small UAS would not exceed the applicable injury severity limit upon impact with a human being, does not contain any exposed rotating parts that would cause lacerations, and does not have any safety defects.
4.2.6 Person Manipulating the Controls. A person other than the remote pilot in command (PIC) who is controlling the flight of a small unmanned aircraft under the supervision of the remote PIC.
4.2.7 Remote Pilot in Command (Remote PIC or Remote Pilot). A person who holds a Remote Pilot Certificate with a small UAS rating and has the final authority and responsibility for the operation and safety of a small unmanned aircraft operation conducted under part 107.
4.2.8 Small Unmanned Aircraft. A small unmanned aircraft weighing less than 55 pounds, including everything that is on board or otherwise attached to the aircraft, and can be flown without the possibility of direct human intervention from within or on the aircraft.
4.2.9 Small Unmanned Aircraft System (small UAS). A small unmanned aircraft and its associated elements (including communication links and the components that control the small unmanned aircraft) that are required for the safe and efficient operation of the small unmanned aircraft in the NAS.
4.2.10 Unmanned Aircraft. An aircraft operated without the possibility of direct human intervention from within or on the aircraft (part 1, § 1.1).
4.2.11 Visual Observer (VO). A person the remote PIC designates as a crewmember who assists the small unmanned aircraft remote PIC and the person manipulating the controls to see and avoid other air traffic or objects aloft or on the ground (part 107, § 107.3).
4.2.12 Voluntary Consensus Standards Body. Voluntary consensus standards bodies are domestic or international organizations that plan, develop, establish, or coordinate voluntary standards using agreed-upon procedures. A voluntary consensus standards body observes principles such as openness, balance of interest, and due process. These bodies may include nonprofit organizations, industry associations, accredited standards developers, professional and technical societies, committees, task forces, or working groups.
Table 4-1. Abbreviations/Acronyms Used in This AC
AAAM Association for the Advancement of Automotive Medicine
AC Advisory Circular
ACR Airman Certification Representative
ACS Airman Certification Standards
ACTS Airman Certificate Testing Service
AD Airworthiness Directive
ADM Aeronautical Decision-Making
AELP Aviation English Language Proficiency
AGL Above Ground Level
AIM Aeronautical Information Manual
AIS Abbreviated Injury Scale
AKTR Airman Knowledge Test Report
ASI Aviation Safety Inspector
AST Aviation Safety Technician
ATC Air Traffic Control
ATO Air Traffic Organization
AWC Aviation Weather Center
C2 Command and Control
CFI Certificated Flight Instructor
CFR Code of Federal Regulations
CG Center of Gravity
COA Certificate of Waiver or Authorization
CoW Certificate of Waiver
CRM Crew Resource Management
CS Control Station
DHS Department of Homeland Security
DOC Declaration of Compliance
DOT Department of Transportation
DPE Designated Pilot Examiner
EDL Enhanced Driver’s License
EID Enhanced Identification Card
EMS Emergency Medical Service
ETC Enhanced Tribal Card
FAA Federal Aviation Administration
FAASTeam FAA Safety Team
FAST Free and Secure Trade
FCC Federal Communications Commission
FRIA FAA-Recognized Identification Area
FSDO Flight Standards District Office
FTN FAA Tracking Number
GCS Ground Control Station
GPS Global Positioning System
IACRA Integrated Airman Certification and Rating Application
ICA Instructions for Continued Airworthiness
ICAO International Civil Aviation Organization
INS Immigration and Naturalization Service
KTC Knowledge Testing Center
LOC Loss of Control
METAR Aviation Routine Weather Report
MMC Merchant Mariner Credential
MOC Means of Compliance
mph Miles per Hour
MSL Mean Sea Level
NAS National Airspace System
NOTAM Notice to Air Missions
NTIA National Telecommunications and Information Administration
NTSB National Transportation Safety Board
NWS National Weather Service
PIC Pilot in Command
PL Public Law
RF Radio Frequency
ROC Regional Operations Center
CHAPTER 4. PART 107 SUBPART A, GENERAL › 4.4 Accident Reporting.
sm Statute Mile
TAF Terminal Aerodrome Forecast
TFR Temporary Flight Restriction
TSA Transportation Security Administration
TWIC Transportation Worker Identification Credential
UAS Unmanned Aircraft System
U.S.C. United States Code
USCIS U.S. Citizenship and Immigration Services
VLOS Visual Line of Sight
VO Visual Observer
W&B Weight and Balance
WINGS Pilot Proficiency Program
4.3 Falsification, Reproduction, or Alteration. The FAA relies on information provided by owners and remote pilots of small UAS when it authorizes operations or when it has to make a compliance determination. Accordingly, the United States government may take appropriate action against a small UAS owner, operator, remote PIC, applicant for a DOC, or anyone else who fraudulently or knowingly provides false records or reports, or otherwise reproduces or alters any records, reports, or other information for fraudulent purposes. Such action could include the FAA’s imposition of civil sanctions and the suspension or revocation of a certificate or waiver (§ 107.5).
4.4 Accident Reporting. The remote PIC of the small unmanned aircraft is required to report an accident to the FAA within 10 days if it meets any of the following thresholds:
1. At least serious injury to any person or any loss of consciousness. A serious injury is an injury that qualifies as Level 3 or higher on the Abbreviated Injury Scale (AIS) of the Association for the Advancement of Automotive Medicine (AAAM). The AIS is an anatomical scoring system that provides a means of ranking the severity of an injury and is widely used by emergency medical personnel. The FAA currently uses serious injury (AIS Level 3) as an injury threshold in other FAA regulations.
AIS 3 Example: A person requires hospitalization, but the injury can fully heal (including, but not limited to, head trauma, broken bone(s), or laceration(s) to the skin that requires suturing).
2. Damage to any property, other than the small unmanned aircraft, if the cost is greater than $500 to repair or replace the property (whichever is lower).
Example: A small unmanned aircraft damages a property with a fair market value of $200, and it would cost $600 to repair the damage. Because the fair
market value is below $500, this accident is not required to be reported. Similarly, if the aircraft causes $200 worth of damage to property with a fair market value of $600, that accident is also not required to be reported because the repair cost is below $500 (§ 107.9).
4.4 Accident Reporting. › 4.4.1 Submitting the Report.
4.4.1 Submitting the Report. The accident report must be made within 10 calendar-days of the operation that created the injury or damage. The report may be submitted to the appropriate FAA Regional Operations Center (ROC) electronically or by telephone. Electronic reporting can be completed at https://www.faa.gov/uas/. To make a report by phone, see Figure 4-1, FAA Regional Operations Centers Telephone List. Reports may also be made to the responsible Flight Standards office (refer to https://www.faa.gov/about/office_org/field_offices/fsdo/). The report should include the following information:
1. Small UAS remote PIC’s name and contact information;
2. Small UAS remote PIC’s FAA airman certificate number;
3. Small UAS registration number issued to the aircraft (FAA registration number);
4. Location of the accident;
5. Date of the accident;
6. Local time of the accident;
7. Whether any serious injury or fatality occurred;
8. Property damaged and extent of damage, if any or known; and
9. Description of what happened.
Figure 4-1. FAA Regional Operations Centers Telephone List
FAA REGIONAL OPERATIONS CENTERS
LOCATION WHERE ACCIDENT OCCURRED: TELEPHONE:
DC, DE, MD, NJ, NY, PA, WV, and VA 404-305-5150
AL, CT, FL, GA, KY, MA, ME, MS, NC, NH, PR, RI, SC, TN, VI, and VT 404-305-5156
AK, AS, AZ, CA, CO, GU, HI, ID, MP, MT, NV, OR, UT, WA, and WY 425-227-1999
AR, IA, IL, IN, KS, LA, MI, MN, MO, ND, NE, NM, OH, OK, SD, TX, and WI 817-222-5006
4.4 Accident Reporting. › 4.4.2 National Transportation Safety Board (NTSB) Reporting.
4.4.2 National Transportation Safety Board (NTSB) Reporting. In addition to the report submitted to the ROC, and in accordance with the criteria established by the NTSB, certain small unmanned aircraft accidents must also be reported to the NTSB. NTSB’s regulations, codified at 49 CFR part 830, require immediate notification when an aircraft accident occurs. NTSB regulations define an “unmanned aircraft accident” as an occurrence associated with the operation of any public or civil UAS that takes place between the time that the system is activated with the purpose of flight and the time that the system is deactivated at the conclusion of its mission, in which any person suffers death or serious injury, or the aircraft has a maximum gross takeoff weight of 300 pounds or greater and sustains substantial damage. NTSB regulations contain specific definitions for “serious injury” and “substantial damage” (49 CFR part 830, § 830.2). For more information, visit https://www.ntsb.gov.
5.2 Aircraft Operation. › 5.2.2 Person Manipulating the Flight Controls.
CHAPTER 5. PART 107 SUBPART B, OPERATING RULES (SMALL UAS)
5.1 Applicability. This chapter provides guidance regarding small unmanned aircraft operating limitations and the responsibilities of the remote pilot in command (PIC), person manipulating the controls, visual observer (VO), and anyone else who may directly participate in the small UAS operation. A person is a direct participant in the small UAS operation if their involvement is necessary for the safe operation of the small UAS.
5.2 Aircraft Operation. Just like a manned-aircraft PIC, the remote PIC of a small unmanned aircraft is directly responsible for and is the final authority for the safe operation of the small unmanned aircraft (§ 107.19). Additionally, a person manipulating the controls (who is not the remote PIC) can participate in flight operations under certain conditions. It is important to note that a person may not operate or act as a remote PIC or VO in the operation of more than one small unmanned aircraft at the same time (§ 107.35). The following items describe the requirements for both a remote PIC and a person manipulating the controls.
5.2.1 Remote PIC. A person acting as a remote PIC of a small UAS under part 107 must obtain a Remote Pilot Certificate with a small UAS rating issued by the FAA prior to small UAS operation (§ 107.12). The remote PIC must have, in that person’s physical possession and readily accessible, this certificate and personal identification during flight operations (§§ 107.7 and 107.67(b)(1) through (3)). Guidance regarding remote pilot certification is found in Chapter 6, Part 107 Subpart C, Remote Pilot Certification.
5.2.1.1 Part 107 permits transfer of control of a small UAS between certificated remote pilots. Two or more certificated remote pilots transferring operational control (i.e., the remote PIC designation) to each other may do so only if they are both capable of maintaining Visual Line of Sight (VLOS) of the small unmanned aircraft without loss of control (LOC). One remote pilot may be designated the remote PIC at the beginning of the operation, and at some point in the operation another remote pilot may take over as remote PIC by positively communicating the transfer of control. The remote PIC assuming control of the small UAS maintains responsibility for the safe operation of the small UAS.
5.2.2 Person Manipulating the Flight Controls. A person who does not hold a Remote Pilot Certificate or a remote pilot who has not met the recurrent training requirements of part 107 may operate the small UAS under part 107, as long as they are directly supervised by a remote PIC and the remote PIC has the ability to take immediate, direct control of the small UAS. This ability is necessary to ensure the remote PIC can quickly address any hazardous situation. The ability of the remote PIC to take over the flight controls immediately could be achieved by using a number of different methods. The operation could involve a “buddy box” type system that uses two control stations (CS): one for the person manipulating the flight controls and one for the remote PIC that allows the remote PIC to override the other CS and immediately take direct control of the small unmanned aircraft (§ 107.19). Another method could involve the remote PIC standing
CHAPTER 5. PART 107 SUBPART B, OPERATING RULES (SMALL UAS) › 5.4 Aircraft Registration.
close enough to the person manipulating the flight controls so that they would be able to physically take over the CS from the other person. Another method could employ the use of an automation system where the remote PIC could immediately engage that system to put the small unmanned aircraft in a pre-programmed “safe” mode such as a hover, a holding pattern, or “return home.”
5.2.3 Automated Operations. An automated operation is generally considered an operation in which the remote pilot inputs a flight plan into the CS, which sends the flight plan to the autopilot on board the small unmanned aircraft. During automated flight, flight control inputs are made by components on board the aircraft, not from a CS. If the remote PIC loses the control link to the small unmanned aircraft, the aircraft would continue to fly the programmed mission/return home to land. During automated flight, the remote PIC must have the ability to change routing/altitude or command the aircraft to land immediately. The ability to direct the small unmanned aircraft may be through manual manipulation of the flight controls or through commands using automation.
5.2.3.1 The remote PIC must retain the ability to direct the small unmanned aircraft to ensure compliance with the requirements of part 107. The remote PIC may transmit a command for the automated aircraft to climb, descend, land now, proceed to a new waypoint, enter an orbit pattern, or return to home. Any of these methods may be used to avoid a hazard or give right-of-way.
5.2.3.2 The use of automation does not allow a person to operate more than one small unmanned aircraft simultaneously (§ 107.35).
5.3 Aeronautical Decision-Making (ADM) and Crew Resource Management (CRM). ADM is a systematic approach to the mental process used by pilots to determine consistently the best course of action in response to a given set of circumstances. A remote PIC uses many different resources to safely operate a small unmanned aircraft and needs to be able to manage these resources effectively. CRM is a component of ADM, in which the pilot of a small unmanned aircraft makes effective use of all available resources: human resources, hardware, and information. Many remote pilots operating under part 107 may use a VO, oversee other persons manipulating the controls of the small UAS, or any other person with whom the remote PIC may interact to ensure safe operations. Therefore, a remote PIC must be able to function in a team environment and maximize team performance. This skill set includes situational awareness, proper allocation of tasks to individuals, avoidance of work overloads for themselves and in others, and effectively communicating with other members of the crew, such as VOs and persons manipulating the controls of a small unmanned aircraft. Appendix A, Risk Assessment Tools, contains expanded information on ADM and CRM, as well as sample risk assessment tools to aid in identifying hazards and mitigating risks.
5.4 Aircraft Registration. A small unmanned aircraft must be registered, in accordance with part 47 or part 48, prior to operating under part 107. Part 48 is the regulation that establishes the streamlined online registration option for small unmanned aircraft that will be operated only within the territorial limits of the United States. The online registration website is https://faadronezone.faa.gov/. Guidance regarding small
5.6 Medical Condition. › 5.6.1 Physical or Mental Incapacitations.
unmanned aircraft registration and marking may be found at https://www.faa.gov/licenses_certificates/aircraft_certification/aircraft_registry/. Alternatively, small unmanned aircraft owners or operators can elect to register under part 47 in the same manner as manned aircraft.
5.4.1 Registration and Permit for Foreign-Owned and Operated Small UAS. If small UAS operations involve the use of foreign civil aircraft, the operator would need to obtain a Foreign Aircraft Permit pursuant to 14 CFR part 375, as described in § 375.41, before conducting any commercial air operations under this authority. Foreign civil aircraft means (a) an aircraft of foreign registry that is not part of the armed forces of a foreign nation, or (b) a U.S.-registered aircraft owned, controlled, or operated by persons who are not citizens or permanent residents of the United States. Application instructions are specified in § 375.43. Applications should be submitted by electronic mail to the Department of Transportation (DOT) Office of International Aviation, Foreign Air Carrier Licensing Division at https://cms.dot.gov/policy/aviation-policy/licensing/for eign-carriers. Foreign-owned and operated small UAS must be registered, as provided for under part 47 or part 48, including submission of an Affidavit of Ownership for Unmanned Aircraft, if necessary. Additional information can be obtained at https://www.faa.gov/licenses_certificates/aircraft_certification/aircraft_registry/UA/. (Refer to Title 49 of the United States Code (49 U.S.C.) § 44101(b)(1) for exceptions.)
5.5 Small Unmanned Aircraft Maintenance, Inspections, and Condition for Safe Operation. A small unmanned aircraft must be maintained in a condition for safe operation. Prior to flight, the remote PIC is responsible for conducting a check of the small unmanned aircraft to verify it is actually in a condition for safe operation (§ 107.15). Guidance regarding how to determine that a small unmanned aircraft is in a condition for safe operation is found in Chapter 7, Small Unmanned Aircraft Maintenance and Inspection.
5.6 Medical Condition. Being able to operate the small unmanned aircraft safely relies on, among other things, the physical and mental capabilities of the remote PIC, person manipulating the controls, VO, and any other direct participant in the small UAS operation. Though the person manipulating the controls of a small unmanned aircraft and VO are not required to obtain an airman medical certificate, they cannot participate in the operation of a small UAS if they know or have reason to know that they have a physical or mental condition that could interfere with the safe operation of the small UAS (§ 107.17).
5.6.1 Physical or Mental Incapacitations. Obvious examples of physical or mental incapacitations that could render a remote PIC, person manipulating the controls, or VO incapable of performing their small UAS operational duties include, but are not limited to, such things as:
1. The temporary or permanent loss of the dexterity necessary to operate the CS to control the small unmanned aircraft safely.
2. The inability to maintain the required “see and avoid” vigilance due to blurred vision.
3. The inability to maintain proper situational awareness of the small unmanned aircraft operations due to illness and/or medication(s), such as after taking medications that caution against driving or operating heavy machinery.
5.7.2 Operations at Night. › 5.7.2.1 A certificated remote pilot receives night operations…
4. A debilitating physical condition, such as a migraine headache or moderate or severe body ache(s) or pain(s) that would render the remote PIC, person manipulating the controls, or VO unable to perform small UAS operational duties.
5. A hearing or speaking impairment that would inhibit the remote PIC, person manipulating the controls, or VO from effectively communicating with each other. In such a situation, the remote PIC must ensure they implement an alternative means of effective communication. For example, a person who is hearing impaired may be able to use sign language to communicate effectively.
5.7 Civil Twilight and Operations at Night. Night is defined in § 1.1 as the time between the end of evening civil twilight and the beginning of morning civil twilight, as published in The Air Almanac, converted to local time. In the continental United States, evening civil twilight is the period of sunset until 30 minutes after sunset and morning civil twilight is the period of 30 minutes prior to sunrise until sunrise. In Alaska, the definition of civil twilight differs and is described in The Air Almanac. The Air Almanac provides tables to determine sunrise and sunset at various latitudes. These tables can also be downloaded from the Naval Observatory and customized for a particular location. The link for the Naval Observatory is https://www.usno.navy.mil/search?SearchableText=air+ almanac+.
5.7.1 Civil Twilight Operations. When small UAS operations occur during civil twilight, the small unmanned aircraft must be equipped with anti-collision lighting visible for at least 3 statute miles (sm). However, the remote PIC may reduce the visible distance of the lighting to less than 3 sm during flight if they have determined that it would be in the interest of safety to do so. For more information on this determination, see paragraph 5.7.2.2.
5.7.2 Operations at Night. Small UAS operations at night may occur only under the two risk mitigation measures listed in § 107.29. First, the remote PIC must have completed either an initial knowledge test or recurrent training that have been updated to include night operations. Second, the small unmanned aircraft must have lighted anti-collision lighting that is visible for at least 3 sm. The remote pilot may rely upon manufacturer statements indicating the anti-collision lighting is visible for 3 sm. However, the remote pilot ultimately remains responsible for verifying that anti-collision lighting is operational, visible for 3 sm, and has a flash rate sufficient to avoid a collision at the operating location.
5.7.2.1 A certificated remote pilot receives night operations privileges and may operate at night only after completing either a knowledge test that contains questions on night physiology and night visual illusions, or through completion of recurrent training. The recurrent training contains the topics of night physiology and night visual illusions. Chapter 6 provides a detailed explanation of both paths for night operations privileges.
CHAPTER 5. PART 107 SUBPART B, OPERATING RULES (SMALL UAS) › 5.9 VLOS Aircraft Operation.
5.7.2.2 As is the case for civil twilight operations, the small unmanned aircraft must be equipped with anti-collision lighting that is visible for at least 3 sm. However, the remote PIC may reduce the intensity of the light if the remote PIC determines it is in the interest of safety to do so. For example, a bright light or a bright strobe light on the small unmanned aircraft in very close proximity to the remote pilot could cause the remote pilot to lose the ability to observe the small unmanned aircraft’s location, speed, attitude, or altitude with accuracy. The remote pilot maintains the discretion to reduce the intensity of the anti-collision lighting when they determine it would be in the best interest of safety to do so. Discretion is an important component of § 107.19, which states that the remote PIC is directly responsible for the operation of the small unmanned aircraft. The remote PIC must ensure the operation of the small unmanned aircraft complies with all regulations of part 107. This includes the requirement to maintain the capability of visually observing the small unmanned aircraft. Section 107.29 does not require small unmanned aircraft operating during the day to have illuminated small unmanned aircraft anti-collision lighting. Lighting is generally not effective for mitigating risk of collision during daytime operations. Remote pilots may exercise their discretion, however, and elect to have lighting on during all daytime operations.
5.7.2.3 A remote PIC or operator may request a waiver of the anti-collision lighting requirement for operations at night and during civil twilight. The process for requesting a waiver is two-fold: the requester must (1) fully describe the proposed operation, and (2) establish the operation can be safely conducted under the terms of a Certificate of Waiver (CoW). Paragraph 5.20 below describes the application process for waivers.
5.8 Operations Over Open-Air Assemblies of Persons. Remote pilots are prohibited from operating a small unmanned aircraft as a Category 1, 2, or 4 operation in sustained flight over open-air assemblies, unless the operation meets the requirements of 14 CFR part 89, § 89.110 or § 89.115(a). Category 3 operations are not allowed over an open-air assembly of persons.
Note: See paragraphs 8.3.2 and 8.3.6.4 for more information regarding open-air assemblies of persons.
5.9 VLOS Aircraft Operation. The remote PIC and person manipulating the controls must be able to see the small unmanned aircraft at all times during flight (§ 107.31). The small unmanned aircraft must be operated closely enough to ensure visibility requirements are met during small UAS operations. This requirement also applies to the VO, if used, during the aircraft operation. The person maintaining VLOS may have brief moments in which they are not looking directly at or cannot see the small unmanned aircraft, but still retain the capability to see the small unmanned aircraft or quickly maneuver it back to VLOS. These moments may be necessary for the remote PIC to look at the controller to determine remaining battery life or for operational awareness. Should the remote PIC or person manipulating the controls lose VLOS of the small unmanned aircraft, they must
5.9.2 VO. › 5.9.2.1 To ensure the VO can carry out their duties, the remote PIC…
regain VLOS as soon as practicable. Even though the remote PIC may briefly lose sight of the small unmanned aircraft, the remote PIC always has the see-and-avoid responsibilities set out in §§ 107.31 and 107.37. The circumstances that may prevent a remote PIC from fulfilling those responsibilities will vary, depending on factors such as the type of small UAS, the operational environment, and distance between the remote PIC and the small unmanned aircraft. For this reason, no specific time interval exists in which interruption of VLOS is permissible, as it would have the effect of potentially allowing a hazardous interruption of the operation. If the remote PIC cannot regain VLOS, the remote PIC or person manipulating the controls should follow pre-determined procedures for the loss of VLOS. The capabilities of the small UAS will govern the remote PIC’s determination as to the appropriate course of action. For example, the remote PIC may need to land the small unmanned aircraft immediately, enter hover mode, or employ a return-to-home sequence. The VLOS requirement does not prohibit actions such as scanning the airspace or briefly looking down at the small unmanned aircraft CS.
5.9.1 Unaided Vision. VLOS must be accomplished and maintained by unaided vision, except vision that is corrected by the use of eyeglasses (spectacles) or contact lenses. Vision aids, such as binoculars, may be used only momentarily to enhance situational awareness. For example, the remote PIC, person manipulating the controls, or VO may use vision aids to avoid inadvertently flying over persons or conflicting with other aircraft. First person view devices may be used during operations, but do not satisfy the VLOS requirement.
5.9.2 VO. The use of a VO is optional. The remote PIC may choose to use a VO to supplement situational awareness and VLOS. Although the remote PIC and person manipulating the controls must maintain the capability to see the small unmanned aircraft, using one or more VOs allows the remote PIC and person manipulating the controls to conduct other mission-critical duties (such as checking displays) while still ensuring situational awareness of the small unmanned aircraft. The VO must be able to communicate effectively with regard to the following:
• The small unmanned aircraft location, attitude, altitude, and direction of flight;
• The position of other aircraft or hazards in the airspace; and
• The determination that the small unmanned aircraft does not endanger the life or property of another (§ 107.33).
5.9.2.1 To ensure the VO can carry out their duties, the remote PIC must ensure the VO is positioned in a location where the VO is able to see the small unmanned aircraft sufficiently to maintain VLOS. The remote PIC can do this by specifying the location of the VO. The FAA also requires the remote PIC and VO coordinate to (1) scan the airspace where the small unmanned aircraft is operating for any potential collision hazard, and (2) maintain awareness of the position of the small unmanned aircraft through direct visual observation (§ 107.33). The remote PIC and VO would accomplish this by the VO communicating to the remote PIC and person manipulating the controls the
5.10 Operation Near Airports, in Certain Airspace, in Prohibited or… › 5.10.1 Small Unmanned Aircraft Operations Near an Airport—Notification…
flight status of the small unmanned aircraft and any collision hazards which may enter the area of operation, so that the remote PIC or person manipulating the controls can take appropriate action. The VO’s visual observation of the small unmanned aircraft and surrounding airspace would enable the VO to inform the remote PIC of the status.
5.9.2.2 To make this communication possible, the remote PIC, person manipulating the controls, and VO must work out a method of effective communication that does not create a distraction. Such a means of communication entails the constant ability to understand one another. The communication method must be determined prior to operation. Effective communication would permit the use of communication-assisting devices, such as a handheld radio, to facilitate communication from a distance.
5.9.3 VLOS at Night. Prior to a small UAS operation at night, the remote PIC should ensure they will be able to keep the small unmanned aircraft within the intended area of operation and within VLOS for the duration of the operation. In almost all cases involving operations at night, the remote PIC may need to restrict the operational area of the small unmanned aircraft. Reduced lighting and contrast at night may make it difficult for remote pilots to fulfill the requirements of § 107.31(a), requiring remote pilots to maintain the capability of visually discerning the location, attitude, altitude, and direction of the flight of the aircraft. A remote pilot cannot solely rely on the small unmanned aircraft’s anti-collision lighting, Ground Control Station (GCS) telemetry data displays, or a combination of the two for compliance with § 107.31.
5.10 Operation Near Airports, in Certain Airspace, in Prohibited or Restricted Areas, or in the Proximity of Certain Areas Designated by a Notice to Air Missions (NOTAM). Small unmanned aircraft may operate in controlled or uncontrolled airspace. Operations in Class B, Class C, or Class D airspace, or within the lateral boundaries of the surface area of Class E airspace designated for an airport, are not permitted unless that person has prior authorization from air traffic control (ATC) (§ 107.41). Information concerning the current authorization process is available at https://www.faa.gov/uas/. The remote PIC must understand airspace classifications and requirements. Failure to do so could be contrary to part 107 regulations and may potentially have an adverse effect on the safety of operations. Small UAS operating under part 107 may not be subject to part 91 requirements, because the equipage and communications requirements outlined in part 91 were designed to provide safety and efficiency in the National Airspace System (NAS). ATC authorizations may depend on operational parameters similar to those found in part 91. The FAA has the authority to approve or deny aircraft operations based on traffic density, controller workload, communication issues, or any other type of operation that could potentially impact the safe and expeditious flow of air traffic in that airspace.
5.10.1 Small Unmanned Aircraft Operations Near an Airport—Notification and Permissions. Unless the flight is conducted within controlled airspace, no notification or authorization is necessary to operate a small unmanned aircraft at or near an airport. When operating in the vicinity of an airport, the remote PIC must be aware of and avoid all traffic patterns and approach corridors to runways and landing areas. The remote PIC must avoid
5.10 Operation Near Airports, in Certain Airspace, in Prohibited or… › 5.10.3 Temporary Flight Restrictions (TFR).
operating in any area in which the presence of the small UAS may interfere with operations at the airport, such as approach corridors, taxiways, runways, or helipads (§ 107.43). The remote PIC must yield right-of-way to all other aircraft, including aircraft operating on the surface of the airport (§ 107.43).
5.10.1.1 Remote PICs are prohibited from operating a small unmanned aircraft in a manner that interferes with operations and traffic patterns at airports, heliports, and seaplane bases (§ 107.43). Small unmanned aircraft must always yield right-of-way to a manned aircraft. A manned aircraft may alter its flightpath, delay its landing, or take off in order to avoid a small unmanned aircraft that may present a potential conflict or otherwise affect the safe outcome of the flight. A small unmanned aircraft hovering 200 feet above a runway may cause a manned aircraft holding short of the runway to delay takeoff, or a manned aircraft on the downwind leg of the pattern to delay landing. While the small unmanned aircraft in this scenario would not present an immediate traffic conflict to the aircraft on the downwind leg of the traffic pattern or to the aircraft intending to take off, nor would it violate the right-of-way provision of § 107.37(a), the small unmanned aircraft would have interfered with the operations of the traffic pattern at an airport.
5.10.1.2 In order to avoid interfering with operations in a traffic pattern, remote PICs should avoid operating in the traffic pattern or published approach corridors used by manned aircraft. When operational necessity requires the remote PIC to operate at an airport in uncontrolled airspace, the remote PIC should operate the small unmanned aircraft in such a way that the manned aircraft pilot does not need to alter their flightpath in the traffic pattern or on a published instrument approach in order to avoid a potential collision.
5.10.2 Air Traffic Organization (ATO). When receiving requests for authorization to operate in controlled airspace, ATO does not approve or deny small unmanned aircraft operations on the basis of equipage that exceeds the part 107 requirements. Additional equipage and technologies, such as geo-fencing, have not been certificated by the FAA and need to be examined on a case-by-case basis in order for the FAA to determine their reliability and functionality. Additionally, requiring staff from ATO to review equipage would place a burden on ATO and detract from other duties. Instead of seeking an authorization, a remote pilot who wishes to operate in controlled airspace because the remote pilot can demonstrate mitigations through equipage may do so by applying for a CoW (see paragraph 5.20).
5.10.3 Temporary Flight Restrictions (TFR). Certain TFRs may be imposed by way of a NOTAM. Refer to https://www.1800wxbrief.com. The remote PIC must check for NOTAMs before each flight to determine whether any airspace restrictions apply to the operation.
5.11 Preflight Familiarization, Inspection, and Actions for Aircraft… › 5.11.1 Prior to Flight. The remote PIC must:
5.10.4 Type of Airspace. Remote PICs must also be aware of the type of airspace in which they will be operating their small unmanned aircraft. Referring to the B4UFly app or a current aeronautical chart (refer to https://www.faa.gov/air_traffic/flight_info/aeronav/digital_pro ducts/) of the intended operating area will aid the small unmanned aircraft remote PIC’s decision making regarding operations in the NAS.
5.11 Preflight Familiarization, Inspection, and Actions for Aircraft Operation. The remote PIC must complete a preflight familiarization, inspection, and other actions, such as crewmember briefings, prior to beginning flight operations (§ 107.49). The FAA has produced many publications providing in-depth information on topics such as aviation weather, aircraft loading and performance, emergency procedures, risk mitigation, ADM, and airspace, which should all be considered prior to operations (see Appendix E, Sample Preflight Assessment and Inspection Checklist). Additionally, all remote pilots are encouraged to review FAA publications (see paragraph 2.3).
5.11.1 Prior to Flight. The remote PIC must:
1. Conduct an assessment of the operating environment. The assessment must include at least the following:
• Local weather conditions;
• Local airspace and any flight restrictions;
• The location of persons and moving vehicles not directly participating in the operation, and property on the surface;
• If conducting operations over people or moving vehicles, ensure their small unmanned aircraft is eligible for the category or categories of operations (see Chapter 8);
• Consider the potential for persons and moving vehicles not directly participating in operations entering the operational area for the duration of the operation;
• Consider whether the operation will be conducted over an open-air assembly of persons; and
• Other ground hazards.
Note: Remote pilots are prohibited from operating a small unmanned aircraft as a Category 1, 2, or 4 operation in sustained flight over open-air assemblies unless the operation meets the requirements of § 89.110 or § 89.115(a).
2. Ensure all persons directly participating in the small UAS operation are informed about the following:
• Operating conditions;
• Emergency procedures;
• Contingency procedures, including those for persons or moving vehicles not directly participating in the operation that enter the operational area;
5.11 Preflight Familiarization, Inspection, and Actions for Aircraft… › 5.11.2 Safety Risk Assessment.
• Roles and responsibilities of each person participating in the operation; and
• Potential hazards.
3. Ensure all control links between the CS and the small unmanned aircraft are working properly. Before each flight, the remote PIC must determine the small unmanned aircraft flight control surfaces necessary for the safety of flight are moving correctly through the manipulation of the small unmanned aircraft CS. If the remote PIC observes that one or more of the control surfaces are not responding correctly to CS inputs, then the remote PIC may not conduct flight operations until correct movement of all flight control surface(s) is established.
4. Ensure sufficient power exists to continue controlled flight operations to a normal landing. This can be accomplished by following the small UAS manufacturer’s operating manual power consumption tables. Another method would be to include a system on the small UAS that detects power levels and alerts the remote pilot when remaining aircraft power is diminishing to a level that is inadequate for continued flight operation.
5. Ensure the small unmanned aircraft anti-collision light(s) function(s) properly prior to any flight that will occur during civil twilight or at night. The remote PIC must also consider, during their preflight check, whether the anti-collision light(s) could reduce the amount of power available to the small unmanned aircraft. The remote PIC may need to reduce the planned duration of the small unmanned aircraft operation to ensure sufficient power exists to maintain the illuminated anti-collision light(s) and to ensure sufficient power exists for the small unmanned aircraft to proceed to a normal landing.
6. Ensure any object attached or carried by the small unmanned aircraft is secure and does not adversely affect the flight characteristics or controllability of the aircraft.
7. Ensure all necessary documentation is available for inspection, including the remote PIC’s Remote Pilot Certificate, identification, aircraft registration, and CoW, if applicable (§ 107.7).
5.11.2 Safety Risk Assessment. These preflight familiarizations, inspections, and actions can be accomplished as part of an overall safety risk assessment. The FAA encourages the remote PIC to conduct the overall safety risk assessment as a method of compliance with the restriction on operating over any person who is not directly involved in the operation, unless the small unmanned aircraft is eligible for an operation over people in accordance with part 107 subpart D. The safety risk assessment also assists with ensuring the small unmanned aircraft will remain clear of other aircraft. Appendix A provides additional guidance on how to conduct an overall safety risk assessment.
5.12 Operating Limitations for Small Unmanned Aircraft. › 5.12.2 Determining Altitude.
5.12 Operating Limitations for Small Unmanned Aircraft. Operations of the small unmanned aircraft must comply with the following limitations:
• Cannot be flown faster than a groundspeed of 87 knots (100 miles per hour (mph));
• Cannot be flown higher than 400 feet above ground level (AGL), unless flown within a 400-foot radius of a structure and does not fly higher than 400 feet above the structure’s immediate uppermost limit;
• Minimum visibility, as observed from the location of the CS, may not be less than 3 sm; and
• Minimum distance from clouds being no less than 500 feet below a cloud and no less than 2,000 feet horizontally from the cloud (§ 107.51).
Note: These operating limitations are intended, among other things, to support the remote pilot’s ability to identify hazardous conditions relating to encroaching aircraft or persons on the ground, and to take appropriate actions to maintain safety.
5.12.1 Determining Groundspeed. Many different types of small unmanned aircraft and different ways to determine groundspeed exist. This guidance will only touch on some of the possible means for the remote PIC to ensure the small unmanned aircraft does not exceed a groundspeed of 87 knots during flight operations. Examples of methods to ensure compliance with this limitation are:
• Installing a Global Positioning System (GPS) device on the small unmanned aircraft that reports groundspeed information to the remote pilot, allowing the remote pilot to determine the wind direction and speed and calculate the small unmanned aircraft airspeed for a given direction of flight;
• Timing the groundspeed of the small unmanned aircraft when it is flown between two or more fixed points, considering wind speed and direction between each point, then noting the power settings of the small unmanned aircraft to operate at or less than 87 knots groundspeed; or
• Using the small unmanned aircraft’s manufacturer design limitations (e.g., installed groundspeed limiters).
5.12.2 Determining Altitude. In order to comply with the maximum altitude requirements of part 107, a remote pilot may determine altitude by:
• Installing a calibrated altitude reporting device on the small unmanned aircraft that reports the small unmanned aircraft altitude above mean sea level (MSL) to the remote pilot, who subtracts the MSL elevation of the CS from the small unmanned aircraft reported MSL altitude to determine the small unmanned aircraft AGL altitude above the terrain or structure;
• Installing a GPS device on the small unmanned aircraft that has the capability of reporting MSL altitude to the remote pilot;
5.14 Operations from Moving Vehicles. › 5.14.2 Applicable Laws.
• Having the remote pilot and VO pace off 400 feet from the small unmanned aircraft while it is on the ground to get a visual perspective of distance so that the remote pilot and VO can recognize and maintain that visual perspective (or closer) when the small unmanned aircraft is in flight; or
• Using the known height of local rising terrain and/or structures as a reference.
5.12.3 Visibility and Distance from Clouds. The remote PIC must determine that the visibility from the CS is at least 3 sm and that the small unmanned aircraft maintains at least 500 feet below clouds and at least 2,000 feet horizontally from clouds. Obtaining local aviation weather reports that include current and forecast weather conditions is one means of determining visibility and cloud clearance. If there is more than one local aviation reporting station near the operating area, the remote PIC should choose the closest one that is most representative of the terrain surrounding the operating area. If local aviation weather reports are not available, the remote PIC cannot operate the small unmanned aircraft until they are able to determine the required visibility and cloud clearances by other reliable means. The small unmanned aircraft cannot be operated above any cloud, and there cannot be obstructions to visibility, such as smoke or a cloud, between the small unmanned aircraft and the remote PIC (§ 107.39).
5.13 Remaining Clear of Other Aircraft. A remote PIC has a responsibility to operate the small unmanned aircraft so that it remains clear of and yields to all other aircraft (§ 107.37). This is traditionally referred to as “see and avoid.” To satisfy this responsibility, the remote PIC must know the location and flightpath of their small unmanned aircraft at all times. The remote PIC must be aware of other aircraft, persons, and property in the vicinity of the operating area, and maneuver the small unmanned aircraft to avoid collision. The remote PIC must take action to ensure other aircraft will not need to maneuver to avoid colliding with the small unmanned aircraft.
5.14 Operations from Moving Vehicles. Part 107 permits operation of a small unmanned aircraft from a moving land or water-borne vehicle over a sparsely-populated area. However, operation from a moving aircraft is prohibited. Additionally, small unmanned aircraft transporting another person’s property for compensation or hire may not be operated from any moving vehicle (§ 107.25).
5.14.1 Waiving the Sparsely-Populated Area Provision. Although the regulation states that operations from a moving vehicle may only be conducted over a sparsely-populated area, this provision may be waived (§§ 107.200 and 107.205). The operation is subject to the same restrictions that apply to all other part 107 operations. The remote PIC operating from a moving vehicle is still required to maintain VLOS. The remote PIC is also responsible for ensuring that no person is subject to undue risk as a result of LOC of the small unmanned aircraft for any reason. If a VO is not located in the same vehicle as the remote PIC, the VO and remote PIC must still maintain effective communication.
5.14.2 Applicable Laws. Other laws, such as State and local traffic laws, may apply to a person driving a vehicle and operating an unmanned aircraft from the vehicle. When operating a small UAS from a moving vehicle, the FAA emphasizes that people involved in the
5.16 Operations While Impaired. › 5.16.1 Medical Conditions.
operation are responsible for complying with applicable State and local laws as well as FAA regulations.
5.15 Transportation of Property. Part 107 permits transportation of property by small unmanned aircraft for compensation or hire. These operations must be conducted within a confined area and in compliance with the operating restrictions of part 107. When transporting property, the transport must occur wholly within the bounds of a single State.
5.15.1 Limitations. As with other operations in part 107, small UAS operations involving the transport of property must be conducted within VLOS of the remote pilot. While the VLOS limitation can be waived for some operations under the rule, it cannot for transportation of property. Additionally, part 107 does not allow the operation of a small UAS from a moving vehicle or aircraft if the small unmanned aircraft is being used to transport property for compensation or hire. This limitation cannot be waived. The maximum total weight of the small unmanned aircraft (including any property being transported) is limited to under 55 pounds. Other provisions of part 107 require the remote pilot to know the small unmanned aircraft’s location; to determine the small unmanned aircraft’s attitude, altitude, and direction; to yield the right-of-way to other aircraft; and to maintain the ability to see and avoid other aircraft.
5.15.2 Hazardous Materials. Section 107.36 prohibits the carriage of hazardous materials by small unmanned aircraft. The carriage of any hazardous material on a small unmanned aircraft may only occur if the operator holds an exemption that permits such carriage. Title 14 CFR part 11 applies to petitions for exemption.
5.16 Operations While Impaired. Part 107 does not allow operation of a small UAS if the remote PIC, person manipulating the controls, or VO is unable to carry out their responsibilities safely (§ 107.27). It is the remote PIC’s responsibility to ensure all crewmembers are not impaired while participating in the operation. While drug and alcohol use are known to impair judgment, certain over-the-counter medications and medical conditions could also affect the ability to operate a small unmanned aircraft safely. For example, certain antihistamines and decongestants may cause drowsiness. Additionally, part 107 prohibits a person from serving as a remote PIC, VO, or other crewmember, or manipulating the controls, if they:
• Consumed any alcoholic beverage within the preceding 8 hours;
• Are under the influence of alcohol;
• Have a blood alcohol concentration of .04 percent or greater; or
• Are using a drug that affects the person’s mental or physical capabilities (§ 91.17).
5.16.1 Medical Conditions. Certain medical conditions, such as epilepsy, may also create a risk to operations. It is the responsibility of remote PICs to determine that their medical condition is under control and they can safely conduct a small UAS operation.
5.17.3 Small unmanned aircraft without remote identification. › 5.17.3.1 Unmanned aircraft equipped with remote identification modules…
5.17 Remote Identification of Unmanned Aircraft Systems. Remote identification requirements are contained in part 89. The information contained in this AC covers the remote identification operational requirements that are relevant to all part 107 operators. Additional information related to remote identification is available in the following ACs:
• AC 89-1, Means of Compliance Process for Remote Identification of Unmanned Aircraft.
• AC 89-2, Declaration of Compliance Process for Remote Identification of Unmanned Aircraft.
5.17.1 After September 16, 2023, most small unmanned aircraft that are registered or required to be registered must comply with remote identification requirements. The serial number of a standard remote identification unmanned aircraft, or of the remote identification broadcast module, if one is installed on the unmanned aircraft, must be listed on the Certificate of Aircraft Registration. The serial number may only be listed on one Certificate of Aircraft Registration at a time. The remote identification broadcast module may be moved from one unmanned aircraft operated under part 107 to another, but the serial number must also be moved from the first aircraft’s Certificate of Aircraft Registration to the second aircraft’s certificate prior to operation. Small unmanned aircraft that are not required to be registered under part 48, such as those where the unmanned aircraft weighs 0.55 pounds or less, must comply with remote identification requirements when operated under any operating part for which registration is required. Remote identification provides data regarding the location and identification of small unmanned aircraft operating in the NAS. It also provides airspace awareness to the FAA, national security agencies, and law enforcement entities, which can be used to distinguish compliant airspace users from those potentially posing a safety or security risk. A list of unmanned aircraft by make and model that are compliant with remote identification will be found at https://www.faa.gov/uas, when developed.
5.17.2 Standard remote identification unmanned aircraft broadcast certain message elements over radio frequency (RF) spectrum. These message elements include: Unmanned Aircraft Identification (either the unmanned aircraft’s serial number or session ID); latitude, longitude, and geometric altitude of both the CS and the unmanned aircraft; the velocity of the unmanned aircraft (including horizontal and vertical speed and direction); a time mark; and an emergency status code (§ 89.110).
5.17.3 Small unmanned aircraft without remote identification. Small unmanned aircraft that are not standard remote identification unmanned aircraft may operate in one of two ways: the small unmanned aircraft may be equipped with a remote identification broadcast module, or the small unmanned aircraft may be operated within an FAA-recognized identification area (FRIA) (§ 89.115).
5.17.3.1 Unmanned aircraft equipped with remote identification modules may be integrated by the manufacturer (e.g., if a manufacturer upgraded or retrofit the aircraft) or a standalone broadcast module installed by the user secured to the unmanned aircraft prior to takeoff. The remote identification broadcast module broadcasts certain message elements directly from the unmanned
CHAPTER 5. PART 107 SUBPART B, OPERATING RULES (SMALL UAS) › 5.20 Certificate of Waiver.
aircraft over RF spectrum. These message elements include: the Unmanned Aircraft Identification, the unmanned aircraft’s serial number; latitude, longitude, and geometric altitude of the unmanned aircraft; latitude, longitude, and geometric altitude of the takeoff location; the velocity of the unmanned aircraft (including horizontal and vertical speed and direction); and a time mark. Small unmanned aircraft using a remote identification broadcast module must be operated within VLOS (§ 89.115(a)).
5.17.3.2 A person operating a small unmanned aircraft that is not a standard remote identification unmanned aircraft may also operate within VLOS within a FRIA, regardless of the type of operation conducted (e.g., part 91, 107, or other). You will be able to access a list of FRIAs at https://www.faa.gov/uas when available (§ 89.115).
5.18 In-Flight Emergency. An in-flight emergency is an unexpected and unforeseen serious occurrence or situation that requires urgent, prompt action. In the case of an in-flight emergency, the remote PIC is permitted to deviate from any rule of part 107 to the extent necessary to respond to that emergency. A remote PIC who exercises this emergency power is required, upon the FAA’s request, to send a written report to the FAA explaining the deviation. Emergency action should be taken in such a way as to minimize injury or damage to property (§ 107.21).
5.19 Careless or Reckless Operation. As with manned aircraft, remote PICs are prohibited from engaging in a careless or reckless operation (§ 107.23). Because small UAS have additional operating considerations that are not present in manned aircraft operations, additional activity may amount to careless or reckless operation if conducted using a small UAS. For example, careless or reckless operation may consist of failure to consider weather conditions near structures, trees, or rolling terrain when operating in a densely populated area.
5.20 Certificate of Waiver. Part 107 includes the option to apply for a CoW. This CoW will allow a small UAS operation to deviate from certain provisions of part 107 if the Administrator finds that the proposed operation can be safely conducted under the terms of that CoW (§ 107.200). A list of the sections of part 107 subject to waiver are listed below:
• Section 107.25: Operation from a moving vehicle or aircraft.
• Section 107.29(a)(2) and (b): Anti-collision light required for operations at night and during periods of civil twilight.
• Section 107.31: Visual line of sight aircraft operation. However, no waiver of this provision will be issued to allow the carriage of property of another by aircraft for compensation or hire.
• Section 107.33: Visual observer.
• Section 107.35: Operation of multiple small unmanned aircraft systems.
• Section 107.37(a): Yielding the right-of-way.
CHAPTER 5. PART 107 SUBPART B, OPERATING RULES (SMALL UAS) › 5.21 Supplemental Operational Information.
• Section 107.39: Operation over people.
• Section 107.41: Operation in certain airspace.
• Section 107.51: Operating limitations for small unmanned aircraft.
• Section 107.145: Operations over moving vehicles.
5.20.1 Applying for a CoW. A CoW can be requested by following the instructions and submitting an application at https://www.faa.gov/uas/.
5.20.2 Application Process. The application must contain a complete description of the proposed operation and a justification, including supporting data and documentation (as necessary), that establishes the proposed operation can safely be conducted under the terms of a CoW. A complete listing of Waiver Safety Explanation Guidelines is posted to the FAA’s website to assist waiver applicants in preparing their proposals and justifications for applications for waiver. They can be found at https://www.faa.gov/uas/commercial_opera tors/part_107_waivers/waiver_safety_explanation_guidelines/. Although not required by part 107, the FAA encourages waiver applicants to submit their application at least 90 days prior to the start of the proposed operation. The FAA will strive to complete review and adjudication of waivers within 90 days; however, the time required for the FAA to make a determination regarding waiver requests will vary based on the complexity of the request.
The amount of data and analysis required as part of the application will be proportional to the specific relief that is requested. For example, a request to waive several sections of part 107 for an operation that takes place in a congested metropolitan area with heavy air traffic will likely require significantly more data and analyses than a request to waive a single section for an operation that takes place in a sparsely-populated area with minimal air traffic. If a CoW is granted, that certificate may include specific special provisions designed to ensure the small UAS operation may be conducted as safely as one conducted under the provisions of part 107. A listing of standard special provisions for part 107 waivers is available on the FAA’s website at https://www.faa.gov/uas/.
5.21 Supplemental Operational Information. Appendix B, Supplemental Operational Information, contains expanded information regarding operational topics that should be considered prior to operations.
6.4 Application Process. › 6.4.1 Remote Pilot Applicants Without Part 61 Certificates.
CHAPTER 6. PART 107 SUBPART C, REMOTE PILOT CERTIFICATION
6.1 Applicability. This chapter provides guidance regarding the airman certification requirements and procedures for persons acting as remote pilot in command (PIC) of a small UAS operated in the National Airspace System (NAS). In the aviation context, the FAA typically refers to “licensing” as “certification.”
6.2 Remote Pilot Certification. An individual exercising the authority of PIC in compliance with part 107 is considered a “remote PIC.” As such, prior to acting as remote PIC, an individual must obtain a Remote Pilot Certificate with a small UAS rating (§ 107.12).
6.3 Eligibility. Pursuant to the requirements of § 107.61, an individual applying for a Remote Pilot Certificate with a small UAS rating must meet the following eligibility requirements, as applicable:
• Be at least 16 years of age.
• Be able to read, speak, write, and understand the English language.
Note: Please refer to § 107.17 for small UAS operating prohibitions for an individual with known medical conditions.
• Be in a physical and mental condition that would not interfere with the safe operation of a small UAS.
• Pass the initial aeronautical knowledge test at an FAA-approved Knowledge Testing Center (KTC). However, an individual who already holds a pilot certificate issued under 14 CFR part 61, other than a student pilot certificate, and meets the flight review requirements specified in part 61, § 61.56 is only required to complete successfully a part 107 online training, found at https://www.faasafety.gov. For more information concerning aeronautical knowledge tests and training, see paragraphs 6.7 and 6.8.
6.4 Application Process. This paragraph provides guidance on how an individual can apply for a Remote Pilot Certificate (§ 107.63).
6.4.1 Remote Pilot Applicants Without Part 61 Certificates. An individual who does not hold a part 61 pilot certificate or a part 61 certificate holder who does not meet the flight review requirements specified in § 61.56 must use the following process. A part 61 pilot who meets the flight review requirements specified in § 61.56 may elect to use this process.
1. Pass an initial aeronautical knowledge test administered at a KTC (see paragraphs 6.7 and 6.8).
2. Complete and submit the Remote Pilot Certificate and/or Rating Application for a Remote Pilot Certificate (FAA Form 8710-13).
• Option 1 (Online Form): This is the fastest and simplest method. The FAA Form 8710-13 application should be completed online using the electronic FAA Integrated Airmen Certificate and Rating Application (IACRA) system (https://iacra.faa.gov/iacra/). An applicant seeking a Remote Pilot Certificate must have already passed an initial Remote Pilot aeronautical knowledge test. Once registered with IACRA, the applicant will log in with their username and password. Click on “Start New Application” and (1) Application Type: “Pilot,” (2) Certifications: “Initial Remote Pilot,” (3) “Other Path Information,” and (4) “Start Application.” Continue through the application process and, when prompted, the applicant may select the knowledge test information provided or enter the 17-digit Knowledge Test Exam ID from the knowledge test in IACRA. Knowledge Test Reports upload immediately to the IACRA system. This allows processing the application for certification without any delay after passing the test. The KTC test proctor verifies the identity of the applicant. Once the applicant completes the online application in IACRA, the applicant signs the application electronically and submits it to the Airman Registry for processing. No FAA representative will be required to sign the application if the applicant was able to self-certify.
Note: When an applicant seeking a Remote Pilot Certificate uses this online option, the application transmits electronically from the applicant to the Airman Registry. The only electronic signature reflected on the IACRA application will be the applicant’s. The Registry confirms basic airman information with the Transportation Security Administration (TSA) prior to generating a Temporary Airman Certificate. Once completed, the applicant receives a confirmation email allowing the applicant to log into the IACRA system and print a copy of the temporary certificate.
• Option 2 (Paper Application): An applicant seeking a Remote Pilot Certificate could also submit a paper application. If the applicant chooses the paper method, the original Remote Pilot initial aeronautical knowledge test report must be mailed with the application to the following address:
DOT/FAA Airmen Certification Branch (AFB-720)
P.O. Box 25082 Oklahoma City, OK 73125
Note: A Temporary Airman Certificate will not be provided to the remote pilot applicant if the applicant does not hold a part 61 certificate. For this reason, it would be in the applicant’s best interest to utilize Option 1 (IACRA system) instead of the paper method, in order to receive a Temporary Airman Certificate once the application has completed the TSA vetting process.
3. Receive permanent Remote Pilot Certificate once all other FAA internal processing is complete.
6.4 Application Process. › 6.4.2 Applicants with Part 61 Certificates.
6.4.2 Applicants with Part 61 Certificates. Instead of the process described above, an individual who holds a part 61 pilot certificate, other than a student pilot certificate, and meets the flight review requirements specified in § 61.56 may elect to apply using the following process:
1. Complete the online Part 107 Small Unmanned Aircraft Systems (small UAS) training located within the FAA Safety Team (FAASTeam) website (https://www.faasafety.gov) and receive a completion certificate.
2. Complete the Remote Pilot Certificate and/or Rating Application for a Remote Pilot Certificate (FAA Form 8710-13).
• Option 1 (Online Application): In almost all cases, the application should be completed online using the electronic FAA IACRA system (https://iacra.faa.gov/iacra/). The applicant must include verification that the applicant completed the online training or passed an initial aeronautical knowledge test. The applicable official document(s) must be uploaded into IACRA either by the applicant or the certifying official.
• Option 2 (Paper): The application may be completed on paper. Using this method, the certificate of completion for the online training must be included with the application. A part 61 pilot, who also meets the requirements of § 61.56, may also take the knowledge test for initial certification. If a part 61 pilot decides to take the knowledge test, the pilot must also include the knowledge test report with their paper application. Please note that the processing time will be increased if a paper application is used.
3. Contact a certifying official such as the local Flight Standards District Office (FSDO), FAA Designated Pilot Examiner (DPE), an Airman Certification Representative (ACR), or a certificated flight instructor (CFI) to make an appointment to validate the applicant’s identification. The applicant must present the completed FAA Form 8710-13 along with the online training completion certificate or knowledge test report (as applicable) and proof of meeting the flight review requirements specified in § 61.56. The FAA Form 8710-13 application will be signed by the applicant after the certifying official examines the applicant’s photo identification and verifies the applicant’s identity. The FAA representative will then sign the application. The identification presented must include a photograph of the applicant, the applicant’s signature, and the applicant’s actual residential address (if different from the mailing address). This information may be presented in more than one form of identification. Acceptable methods of identification include, but are not limited to U.S. drivers’ licenses, government identification cards, passports, and military identification cards (see Appendix D, Remote Pilot Certification and Applicant Identity Verification). If using paper or IACRA method, an appropriate FSDO representative, a DPE, or an ACR will issue the applicant a Temporary Airman Certificate.
Note: A CFI is not authorized to issue a temporary certificate. The applicant can print their own Temporary Airman Certificate after receiving an email from the FAA notifying the applicant that it is available. The FSDO signs and
mails the application to AFB-720 for the issuance of the permanent certificate. Flight instructors may refer to AC 61-141.
6.7 Aeronautical Knowledge Test. › 6.7.1 Knowledge Test.
6.5 Security Disqualification. After the FAA receives the application, the TSA will vet the applicant prior to issuance of a temporary Remote Pilot Certificate. If the vetting is successful, the FAA will issue a permanent Remote Pilot Certificate. If the vetting is not successful, the applicant will be disqualified and a temporary or permanent pilot certificate will not be issued. Individuals who believe they improperly failed a security threat assessment may appeal the decision to the TSA.
6.6 FAA Tracking Number (FTN) Requirement. Beginning January 13, 2020, all applicants must establish an FTN within IACRA before taking any FAA airman knowledge test.
• This identification number will be printed on the applicant’s Airman Knowledge Test Report (AKTR) in replacement of the Applicant ID number.
• To register for an FTN in IACRA, applicants will need to visit the IACRA website and follow the instructions provided.
• You can access IACRA at https://iacra.faa.gov/iacra/.
• Once you have your FTN, you can register to take your FAA Airman Knowledge Test by going to the following registration and scheduling website operated by PSI Services LLC: https://faa.psiexams.com/FAA/login.
• You can find FTN Frequently Asked Questions (and Answers) at https://www.faa.gov/training_testing/testing/acts/media/ftn_faqs.pdf.
• You can find a video about the registration process for an FTN in IACRA at https://www.youtube.com/watch?v=ETLsH8BruBM&feature=youtu.be.
6.7 Aeronautical Knowledge Test. The FAA publishes the Remote Pilot – Small Unmanned Aircraft Systems Airman Certification Standards (ACS) (https://www.faa.gov/training_te sting/testing/acs/) that provides the standards for the Knowledge Test. Materials helpful for preparation are available at https://www.faa.gov/about/office_org/headquarters_office s/avs/offices/afx/afs/afs600/afs630/. Chapter 2, References, lists FAA publications and online resources that will assist in preparing for remote pilot certification.
Note: The following information regarding the knowledge test applies to individuals who do not hold a current part 61 airman certificate.
6.7.1 Knowledge Test. As described in paragraph 6.4, an individual applying for a Remote Pilot Certificate with a small UAS rating must pass an initial aeronautical knowledge test given at an FAA-approved KTC. In order to take an aeronautical knowledge test, an applicant must schedule an appointment with the KTC. On the day of scheduled testing, the applicant must provide proper government-issued photo identification to KTC. The location of the closest KTC can be found at https://faa.psiexams.com/FAA/login. The knowledge test will cover the aeronautical knowledge areas listed below:
6.7 Aeronautical Knowledge Test. › 6.7.2 Recurrent Training.
1. Applicable regulations relating to small UAS rating privileges, limitations, and flight operation;
2. Airspace classification, operating requirements, and flight restrictions affecting small unmanned aircraft operations;
3. Aviation weather sources and effects of weather on small unmanned aircraft performance;
4. Small unmanned aircraft loading;
5. Emergency procedures;
6. Crew Resource Management (CRM);
7. Radio communication procedures;
8. Determining the performance of the small unmanned aircraft;
9. Physiological effects of drugs and alcohol;
10. Aeronautical decision-making (ADM) and judgment;
11. Airport operations;
12. Maintenance and preflight inspection procedures; and
13. Operation at night.
6.7.1.1 A part 61 certificate holder who meets the flight review requirements specified in § 61.56 may complete training instead of taking the knowledge test (see paragraph 6.7). This training includes the following topics:
1. Applicable regulations relating to small UAS rating privileges, limitations, and flight operation;
2. Effects of weather on small unmanned aircraft performance;
3. Small unmanned aircraft loading;
4. Emergency procedures;
5. CRM;
6. Determining the performance of small unmanned aircraft;
7. Maintenance and preflight inspection procedures; and
8. Operation at night.
6.7.2 Recurrent Training. After an individual receives a Remote Pilot Certificate with a small UAS rating, that individual must retain the level of knowledge required to safely operate a small UAS in the NAS. To continue exercising the privileges of a Remote Pilot Certificate, the certificate holder must successfully complete recurrent training within 24 calendar-months of passing either an initial knowledge test or initial knowledge training. Figure 6-1, Recurrent Training Cycle Examples, illustrates an individual’s potential renewal cycles.
6.8 Aeronautical Knowledge Training. › 6.8.1 Training.
Figure 6-1. Recurrent Training Cycle Examples
Individual passes an initial aeronautical knowledge test on September 13, 2020. Then
Recurrent training must be completed no later than September 30, 2022, which does not exceed 24 calendar-months.
Individual does not pass recurrent training until October 5, 2020.
Then
Individual may not exercise the privileges of the Remote Pilot Certificate between October 1, 2020, and October 5, 2020, when the training is completed. The next recurrent knowledge training must be completed no later than October 31, 2022, which does not exceed 24 calendar-months.
Individual elects to take recurrent training on or prior to September 30, 2020. The recurrent training is completed on July 15, 2020.
Then
The next recurrent training must be completed no later than July 31, 2022, which does not exceed 24 calendar-months.
6.8 Aeronautical Knowledge Training. This paragraph is applicable to individuals who hold a part 61 airman certificate, other than a student pilot certificate, and meet the flight review requirements specified in § 61.56.
6.8.1 Training. As described in paragraph 6.7, an individual who holds a part 61 airman certificate, other than a student pilot certificate, and meets the flight review requirements specified in § 61.56 may complete training instead of the initial knowledge test. The training can be taken online at https://www.faasafety.gov. The FAA offers options for training completion in addition to those available on https://www.faasafety.gov. Other options include completion of special pilot proficiency programs, such as an FAA-provided WINGS course specific to small UAS operations. These programs will offer tools and resources to strengthen decision-making skills and enable the remote pilot to continue to ensure they operate safely within the bounds of part 107.
7.2 Maintenance. › 7.2.3 Performing Maintenance.
CHAPTER 7. SMALL UAS MAINTENANCE AND INSPECTION
7.1 Applicability. Section 107.15 requires the remote PIC to perform checks of the small unmanned aircraft prior to each flight to determine whether the small UAS is in a condition for safe operation. This chapter provides guidance on how to inspect and maintain a small UAS. Additionally, Appendix C, Small UAS Maintenance and Inspection Best Practices, contains expanded information and best practices for small UAS maintenance and inspection.
7.2 Maintenance. Small UAS maintenance includes scheduled and unscheduled overhaul, repair, inspection, modification, replacement, and system software upgrades of the small UAS and its components necessary for flight. Whenever possible, the operator should maintain the small UAS and its components in accordance with manufacturer’s instructions. The aircraft manufacturer may provide the maintenance program, or, if one is not provided, the applicant may choose to develop one. See paragraph 7.3.5 for suggested benefits of recordkeeping. (See paragraph 8.3.7.4 for Category 4 maintenance requirements. See paragraph 8.3.7.4.1 for Category 4 record retention requirements and owner and operator responsibilities.)
7.2.1 Scheduled Maintenance. The small UAS manufacturer may provide documentation for scheduled maintenance of the entire small unmanned aircraft and associated system equipment. The manufacturer may identify components of the small UAS that should undergo scheduled periodic maintenance or replacement based on time-in-service limits (such as flight hours, cycles, and/or the calendar-days). Operators should adhere to the manufacturer’s recommended schedule for such maintenance, in the interest of achieving the longest and safest service life of the small UAS.
7.2.1.1 If the small UAS manufacturer or component manufacturer does not provide scheduled maintenance instructions, the operator should establish a scheduled maintenance protocol. Such protocol could entail documenting any repair, modification, overhaul, or replacement of a system component resulting from normal flight operations, and recording the time-in-service for that component at the time of the maintenance procedure. Over time, the operator should then be able to establish a reliable maintenance schedule for the small UAS and its components.
7.2.2 Unscheduled Maintenance. During the course of a preflight inspection, the remote PIC may discover a small UAS component is in need of servicing (such as lubrication), repair, modification, overhaul, or replacement outside of the scheduled maintenance period as a result of normal flight operations or resulting from a mishap. In addition, the small UAS manufacturer or component manufacturer may require an unscheduled system software update to correct a problem. In the event such a condition is found, flight operations should not occur until the issue is corrected.
7.2.3 Performing Maintenance. In some instances, the small UAS or component manufacturer may require completion of certain maintenance tasks by the manufacturer or by a person or facility (personnel) the manufacturer specifies. Maintenance should occur in
7.3 Preflight Inspection. › 7.3.4 Preflight Inspection Items.
accordance with the manufacturer’s instructions. However, if the operator declines to use the manufacturer or personnel the manufacturer recommends are unable to perform the required maintenance, the operator should consider the expertise of maintenance personnel familiar with the specific small UAS and its components.
7.2.3.1 If the operator or other maintenance personnel are unable to repair, modify, or overhaul a small UAS or component back to its safe operational specification, the operator should replace the small UAS or component with one that is in a condition for safe operation. All required maintenance should be completed before each flight, and preferably in accordance with the manufacturer’s instructions or, in lieu of that, within known industry best practices.
7.3 Preflight Inspection. Pursuant to the requirements of § 107.49, in addition to assessing the intended area of operation and planning the operation as described above in paragraph 5.10, the remote PIC must inspect the small UAS to ensure that it is in a condition for safe operation prior to each flight. This inspection includes examining the small UAS for equipment damage or malfunction(s). This preflight inspection should be conducted in accordance with the small UAS manufacturer’s inspection procedures when available (usually found in the manufacturer’s owner or maintenance manual) and/or an inspection procedure developed by the small UAS owner or operator.
7.3.1 Creating an Inspection Program. As an option, small UAS owners or operators may wish to create an inspection program for their small UAS. The person creating such an inspection program may find sufficient details to assist in the development of a suitable inspection program tailored to a specific small UAS in a variety of industry programs.
7.3.2 Scalable Preflight Inspection. The preflight check as part of the inspection program should include an appropriate small UAS preflight inspection that is scalable to the small UAS, program, and operation that the remote PIC performs prior to each flight. An appropriate preflight inspection should encompass the entire system in order to determine a continued condition for safe operation prior to flight.
7.3.3 Title 14 CFR Part 43 Appendix D Guidelines. Another option and best practice may include opting to comply with the portions of part 43 appendix D. Although part 43 appendix D is technically a maintenance inspection checklist and not a preflight inspection checklist, it provides a logical and systematic approach to performing an inspection by dividing the aircraft into subgroups. It details inspection of the airframe, then the flight controls, then the batteries, then the engine, etc. Unlike manned aircraft that require significant disassembly, most small UAS inspection items are visible without necessitating the need for disassembly. In the absence of a manufacturer’s instructions, an operator may use part 43 appendix D as a guide to develop their own inspection program, but it is not comprehensive, as it does not address unique UAS features like datalinks or support equipment. An operator would need to identify those items not covered and include them in their inspection program.
7.3.4 Preflight Inspection Items. Even if the small UAS manufacturer has a written preflight inspection procedure, the FAA recommends the remote PIC ensure the following
inspection items be incorporated into the remote PIC’s preflight inspection procedure. Such a practice will ensure the remote PIC accurately determines that the small UAS is in a condition for safe operation. The preflight inspection should include a visual or functional check of the following items.
1. Visual condition inspection of the small UAS components;
2. Airframe structure (including undercarriage), all flight control surfaces, and linkages;
3. Registration markings, for proper display and legibility (part 48, § 48.205);
4. Moveable control surface(s), including airframe attachment point(s);
5. Servo motor(s), including attachment point(s);
6. Propulsion system, including powerplant(s), propeller(s), rotor(s), ducted fan(s), etc.;
7. Check fuel for correct type and quantity;
8. Check that any equipment, such as a camera, is securely attached;
9. Check that control link connectivity is established between the aircraft and the CS;
10. Verify communication with small unmanned aircraft and that the small UAS has acquired GPS location from the minimum number of satellites specified by the manufacturer;
11. Verify all systems (e.g., aircraft and control unit) have an adequate power supply for the intended operation and are functioning properly;
12. Verify correct indications from avionics, including control link transceiver, communication/navigation equipment, and antenna(s);
13. Display panel, if used, is functioning properly;
14. Check ground support equipment, including takeoff and landing systems, for proper operation;
15. Verify adequate communication between CS and small unmanned aircraft exists; check to ensure the small UAS has acquired GPS location from the minimum number of satellites specified by the manufacturer;
16. Check for correct movement of control surfaces using the CS;
17. Check flight termination system, if applicable;
18. Check that the anti-collision light is functioning (if operating during civil twilight and night);
19. Calibrate small UAS compass prior to any flight;
20. Verify controller operation for heading and altitude;
21. Start the small UAS propellers to inspect for any imbalance or irregular operation;
22. At a controlled low altitude, fly within range of any interference and recheck all controls and stability; and
23. Check battery levels for the aircraft and CS.
7.3 Preflight Inspection. › 7.3.5 Benefits of Recordkeeping.
7.3.5 Benefits of Recordkeeping. Small UAS owners and operators may find recordkeeping to be beneficial. This may be done by documenting any repair, modification, overhaul, or replacement of a system component resulting from normal flight operations, and recording the time-in-service for that component at the time of the maintenance procedure. The operator would then be able to establish a reliable maintenance schedule for the small UAS and its components. The use of hardcopy and/or electronic logbook format for recordkeeping, inclusive of all periodic inspections, maintenance, preventative maintenance, repairs, and alterations performed on the small UAS, is useful in documenting the history of the small UAS. Recordkeeping would include all components of the small UAS, including: small unmanned aircraft, CS, launch and recovery equipment, Command and Control (C2) link equipment, payload, and any other components required to safely operate the small UAS.
Continue reading ↓ 120 of 302 passages shown