Radar Vectors
FAA Order Cancelled Issued Sep 30, 2008 AFS-1 306 pages Copy saved Nov 18, 2026

Order 8900.2 General Aviation Airman Designee Handbook (Consolidated with Changes 1 and 2)

This document is cancelled. Cancelled by 8900.2A. Check the official source before relying on it.

Official source ↗ Open PDF

5. Disposition of Transmittal Paragraph.

CHANGE

U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

ORDER 8900.2 CHG 2

National Policy Effective Date:

7/24/13

SUBJ: General Aviation Airman Designee Handbook

1. Purpose of This Order. This change transmits new and revised portions of the order.

2. Audience. The primary audience for this order is Flight Standards District Office (FSDO) aviation safety inspectors (ASI). The secondary audience includes Flight Standards branches and divisions in the regions and in headquarters.

3. Where You Can Find This Order. This change may be accessed by Flight Standards personnel through the Flight Standards Information Management System (FSIMS) at http://fsims.avs.faa.gov. Operators and the public can find this order at http://fsims.faa.gov.

4. Explanation of Policy Changes. This change incorporates new information as follows:

• Incorporates information in accordance with the publication of the Pilot Certification and Qualifcation Requirements for Air Carrier Operations Final Rule. • Updates the guidance to designees on procedures for conducting certificate holder oral and practical tests and issuing Temporary Airman Certificates. • For the items listed below, the information has been updated in FAA Order 8900.1, Flight Standards Information Management System (FSIMS) as a result of this rulemaking project. The corresponding information in this order has been removed and now points to Order 8900.1 for guidance. Some figures have been removed. A few additional notes were added concerning knowledge test validity and the inability to use Integrated Airman Certification and/or Rating Application (IACRA) for the restricted privileges Airline Transport Pilot (ATP) Certificate.

• Verification of an Applicant’s Identity. • Illegal Substance Conviction. • Completion of FAA Form 8710-1. • Conduct an ATP Certification, Including Additional Category/Class Ratings at the ATP Certification Level. • Procedures for Issuing a Second-in-Command (SIC) Pilot Type Rating.

5. Disposition of Transmittal Paragraph. This change will remain in FSIMS until superseded by a revision to this order.

Distribution: Electronic Only Initiated By: AFS-600

PAGE CHANGE CONTROL CHART

Remove Pages Dated Insert Pages Dated

i 8/16/10 i 7/24/13 ii 8/16/10 ii 7/24/13 iii 8/16/10 iii 7/24/13 iv 8/16/10 iv 7/24/13 v 8/16/10 v 7/24/13 vi 8/16/10 vi 7/24/13 vii 8/16/10 vii 7/24/13 ix 8/16/10 ix 7/24/13 x 8/16/10 x 7/24/13 1-2 8/16/10 1-2 7/24/13 7-32 8/16/10 7-32 7/24/13 7-33 8/16/10 7-33 7/24/13 7-34 8/16/10 7-34 7/24/13 7-35 8/16/10 7-35 7/24/13 7-36 8/16/10 7-36 7/24/13 7-37 8/16/10 7-37 7/24/13 7-40 8/16/10 7-40 7/24/13 7-41 8/16/10 7-41 7/24/13 7-42 8/16/10 7-42 7/24/13 7-47 8/16/10 7-47 7/24/13 7-48 8/16/10 7-48 7/24/13 7-61 8/16/10 7-61 7/24/13 7-74 8/16/10 7-74 7/24/13 7-81 8/16/10 7-81 7/24/13 7-82 8/16/10 7-82 7/24/13 7-91 8/16/10 7-91 7/24/13 7-94 8/16/10 7-94 7/24/13 7-99 8/16/10 7-99 7/24/13 7-106 8/16/10 7-106 7/24/13 7-137 8/16/10 7-137 7/24/13 7-163 8/16/10 7-163 7/24/13 7-170 8/16/10 7-170 7/24/13 7-185 thru 7-203 8/16/10 7-185 thru 7-203 7/24/13 A-1 8/16/10 A-1 7/24/13 C-1 8/16/10 C-1 7/24/13 for John M. Allen Director, Flight Standards Service

FOREWORD › 3. When differences in guidance appear between this order and FAA Order…

U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

National Policy

ORDER

8900.2

Effective Date:

8/16/10

SUBJ: General Aviation Airman Designee Handbook

FOREWORD

1. In 2006, Aviation Safety (AVS) published Federal Aviation Administration (FAA) Order VS 1100.2, Managing AVS Delegation Programs, current edition, which provided direction for the management and oversight of AVS delegation programs, including Flight Standards Service (AFS) designees. During the next 2 years, the AVS Delegation Steering Group, which includes representation from AFS, identified important goals including the integration of AFS designee policy. An AFS working group, including policy holders for each general aviation airman designee type, was formed to work on this consolidated order. This order contains integrated procedures for the selection, appointment, oversight, training, renewal, termination, and appeal of AFS general aviation airman designees in accordance with Order VS 1100.2.

2. This order contains procedures for authorized general aviation airman designees and inspectors to conduct certificate holder oral and practical tests and issue temporary airman certificates.

3. When differences in guidance appear between this order and FAA Order 8900.1, Flight Standards Information Management System (FSIMS), Volume 13, Flight Standards Designees, current edition, use the document with the most current revision date. This order also applies to all aviation safety inspectors (ASI) (referred to in this order as ASIs or inspectors) who review and approve airman application and testing files for general aviation airman designees.

Distribution: Electronic Only Initiated By: AFS-600

Table of Contents

Table of Contents Paragraph Page

Chapter 1. General Information

1. Purpose of This Order … 1-1 2. Audience … 1-1 3. Where You Can Find This Order … 1-1 4. What This Order Cancels … 1-1 5. Explanation of Policy Changes … 1-2 6. Delegation/Rescission of a Designee Authorization … 1-2 7. Role of the Designee … 1-2 8. Definitions … 1-2

Chapter 2. Selection and Appointment

1. Selection … 2-1 2. Appointment … 2-3 3. General Eligibility Requirements … 2-4

Chapter 3. Oversight, Training, and Renewal

1. Oversight … 3-1 2. Initial Training Seminar … 3-1 3. Orientation … 3-1 4. Recurrent Training … 3-2 5. Expiration … 3-2 6. Renewal … 3-3 7. Knowledge and Skill … 3-4

Chapter 4. Termination and Appeal

1. Termination … 4-1 2. Types of Termination … 4-1 3. Termination Letter … 4-1 4. Appeal … 4-1

Chapter 5. Privileges, Limitations, and Responsibilities

1. Privileges … 5-1 2. Limitations … 5-2 3. Responsibilities … 5-3

Chapter 6. Technical Personnel Examiner Program

Section 1. General

1. Additional Requirements for Appointment … 6-1 2. Aviation Mechanic Tests … 6-2 3. Parachute Rigger Tests … 6-2 4. FAA Certification Policy … 6-3 5. Limitations … 6-3 6. Designations Issued … 6-3 7. Designee Materials … 6-4 8. Security … 6-4

ii

Table of Contents (Continued) Paragraph Page

Table of Contents (Continued)

Section 2. Conducting and Grading Tests

9. Preparation … 6-5 10. Applicant Eligibility … 6-9 11. Evaluating Applicant Performance … 6-12 12. Conducting the Tests … 6-14 13. Test Planning Sheets are Required for Each Oral and Practical Test Given … 6-16 14. Recording the Results of Tests … 6-17 15. When the Applicant Passes … 6-17 16. Applicants Under 18 Years of Age … 6-19 17. When the Applicant Fails … 6-20 18. Disposition of Files … 6-21 19. Issuance of FAA Form 8060-4 by a TPE When Oral and Practical Tests are Not Administered … 6-22 20. Reconstruction of a Lost Certification File … 6-23 Chapter 7. Designated Pilot Examiner Program

Section 1. General

1. Additional Qualifications … 7-1 2. Specific Eligibility Requirements … 7-3 3. Types of Designation … 7-9 4. Practical Test … 7-11 5. Additional Designations … 7-11 6. Examiner COA Letters … 7-12

Section 2. Conduct Practical Test/Certification Functions

7. General … 7-15 8. Testing Applicants Trained by the Examiner … 7-19 9. Examiner Limitations … 7-19 10. Status of Examiners During Practical Tests … 7-20 11. Carriage of Passengers During Practical Tests … 7-23 12. Aircraft Used for Practical Tests … 7-23 13. Aircraft Equipment … 7-26 14. Flight Simulators, Flight Training Devices, and Personal Computer-Based Aviation Training Devices … 7-26 15. Engine Shutdown on Multiengine Airplanes During the Practical Test … 7-27 16. Structure of the Practical Test … 7-27 17. Practical Test Discontinuance … 7-29 18. Repeating Maneuvers on Practical Tests … 7-29 19. Practical Test Briefings … 7-30 20. Segmented Practical Tests (Planned) … 7-30 21. Retest in Event of Failure … 7-31 22. Accidents and Incidents During Practical Tests … 7-31 23. Practical Test Standards … 7-31 24. Prerequisites for Practical Tests … 7-32

iii

Table of Contents (Continued)

Paragraph Page

25. Verification of an Applicant’s Identity … 7-36 26. Illegal Substance Conviction … 7-36 27. Completion of FAA Form 8710-1 … 7-37 28. Preparation of the Certification File … 7-37 29. Review of an Examiner’s Decision … 7-38 30. Issuance of FAA Form 8060-4 … 7-38 31. Limitations … 7-39 32. Issuance of FAA Form 8060-5 … 7-41 33. Part 141 Stage Checks … 7-41 34. Blue Seal Certificates … 7-42 35. Flight and Duty Time as a DPE … 7-42 36. Procedures … 7-42 Section 3. Issue a Student Pilot Certificate

37. General … 7-47 38. Nonrenewable … 7-47 39. Procedures … 7-48 Section 4. Special Emphasis Items

40. Special Emphasis Items … 7-50 41. Dangers Associated with Simulation of Power Failure in Single-Engine Airplanes by the Interruption of Fuel Flow … 7-50 42. Pilot External Vigilance (Scan Program) … 7-51 43. Accurate Position Reporting and Collision Avoidance … 7-51 44. Instrument Flying Skills—Partial Panel … 7-52 Section 5. Flight Reviews and Competency Checks

45. Flight Reviews and Competency Checks … 7-52 46. Examiner or Inspector Participation … 7-53 47. Application for a Flight Review or Competency Check … 7-53 48. Combining Flight Reviews and Competency Checks … 7-53 49. Evaluating the Flight Review … 7-53 50. Length of Review … 7-53 51. Logbook Endorsements … 7-54 52. Recent Instrument Experience, § 61.57 … 7-54 53. High Performance Airplane Check, § 61.31(f) … 7-55 54. Complex Airplane Check, § 61.31(e) … 7-55 55. Self-Launching or Powered Sailplane Flight Checks … 7-56 56. Night Vision Goggles (NVG) Training, Endorsement, and Qualification for Pilots and Flight Instructors … 7-56 Section 6. Conduct a Recreational Pilot Certification, Including Additional

Category/Class Ratings at the Recreational Pilot Certification Level 57. General … 7-59 58. Additional Category and Class Ratings … 7-61 59. Upgrading to a Private Pilot Certificate … 7-61 60. Procedures … 7-61

iv

Table of Contents (Continued) Paragraph Page

Section 7. Conduct a Sport Pilot Certification

61. General … 7-66 62. Procedures … 7-67 Section 8. Conduct a Private Pilot Certification, Including Additional Category/Class

Ratings at the Private Pilot Certification Level 63. General … 7-70 64. Eligibility Requirements … 7-70 65. Limitations … 7-72 66. Categories and Classes … 7-73 67. Recreational Pilot Upgrades … 7-73 Section 9. Conduct a Commercial Pilot Certification, Including Additional

Category/Class Ratings at the Commercial Pilot Certification Level 68. General … 7-74 69. Eligibility Requirements … 7-74 70. Categories and Classes … 7-76 71. Instructor Privileges in Lighter-Than-Air Aircraft … 7-77 72. Complex Airplane Requirements … 7-77 73. Procedures … 7-77 Section 10. Conduct an Airline Transport Pilot (ATP) Certification, Including Additional

Category/Class Ratings at the ATP Certification Level 74. General … 7-82 Section 11. Conduct an Instrument Rating Certification

75. General … 7-82 76. Eligibility Requirements … 7-83 77. Types of Instrument Ratings Issued … 7-84 78. Flight Controls … 7-84 79. Use of Nonapproved Instrument Approach Procedures … 7-84 80. Limitations … 7-84 81. Procedures … 7-85 Section 12. Conduct a Pilot Type Rating Certification

82. General … 7-89 83. Pilot Type Rating That May be Performed as Either a Single Pilot or With an SIC .. 7-91 84. Procedures … 7-102 Section 13. Procedure for Issuing a Second-in-Command Pilot Type Rating

85. General … 7-105

v

Table of Contents (Continued) Paragraph Page

Section 14. Conduct a Private Pilot Certification for Weight Shift Control and Powered

Parachute, Including Additional Category/Class Ratings at the Private Pilot Certification Level 86. General … 7-106 87. Eligibility Requirements … 7-106 88. Limitations … 7-108 89. Categories and Classes … 7-109 90. Procedures … 7-109 Section 15. Conduct a Flight Instructor with a Sport Pilot Rating Practical Test for an

Initial, Renewal, or Reinstatement 91. General … 7-113 92. General Procedures Initial Certification … 7-113 93. General Procedures for Renewal or Reinstatement … 7-115 94. Denial of Renewal or Reinstatement … 7-116 95. Gold Seal Flight Instructor Certificates … 7-116 96. Category and Class Privileges for a Flight Instructor Certificate with a Sport Pilot Rating … 7-116 97. Procedures … 7-117 Section 16. Conduct a Flight Instructor Practical Test for an Initial, Renewal,

Reinstatement Certification, or an Additional Category/Class Rating to a Flight Instructor Certificate 98. General … 7-121 99. Knowledge Test … 7-122 100. Practical Test … 7-123 101. Eligibility Requirements … 7-123 102. General Procedures for Renewal or Reinstatement … 7-126 103. Denial of Renewal or Reinstatement … 7-126 104. Gold Seal Flight Instructor Certificates … 7-126 105. Category, Class, and Instrument Ratings Placed on a Flight Instructor Certificate . 7-127 106. Limitations … 7-128 107. Procedures … 7-128 Section 17. Conduct Pilot Proficiency Checks as a Pilot Proficiency Examiner

108. General … 7-133 109. Limitations … 7-133 110. Experience Requirements for Designation as a PPE … 7-133 111. Practical Test … 7-134 112. COA Letter … 7-134 113. Additional Designations … 7-135 114. PIC Proficiency Check Procedures … 7-135 115. Proficiency Check Records … 7-135

vi

Table of Contents (Continued) Paragraph Page

Section 18. Accomplish Designation/Issue Certificates as an ACR, Limited to Examining

Authority under Part 141 116. General … 7-136 117. Selection of ACRs … 7-136 118. Certification of Graduates … 7-137 Section 19. Accomplish Designation/Issue Certificates as an ACR Employed Solely by

a FIRC Sponsor 119. General … 7-138 120. Selection of ACRs … 7-138 121. Flight Instructor Certificate and Ratings Issued on the Basis of Military Competence by an MCE and MC/FPE … 7-140 122. Certification of Graduates … 7-142 Section 20. Accomplish Designation/Conduct Functions as an MCE, FPE, MC/FPE,

GIE, and FIRE 123. Background … 7-143 124. General Information for MCE, FPE, and MC/FPE Designations … 7-144 125. Issuance of a U.S. Private Pilot Certificate and Ratings Based on Foreign Pilot Licenses … 7-146 126. Pilot Certificates and Ratings Issued on the Basis of Military Competence by an MCE and MC/FPE … 7-148 127. Compliance with Other Provisions … 7-149 128. Designation of an FIRE … 7-149 129. Designation of a GIE … 7-150 Section 21. Accomplish Issuance of a U.S. Pilot Certificate Based on a Foreign-Pilot License 130. General Information … 7-151 131. Procedures … 7-165 Section 22. IACRA Process

132. General … 7-169 133. Procedures … 7-170

Chapter 8. Administrative Information

1. Distribution … 8-1 2. Deviations … 8-1 3. Suggestions or Comments … 8-1

Appendix A. Acronyms and Abbreviations … A-1

Appendix B. Practical Test Standards Judgment Assessment Matrices … B-1

Appendix C. Directive Feedback Information … C-1

vii

List of Figures

List of Figures Figure Page

6-1. Instructions for Completing FAA Form 8610-2, Airman Certificate and/or Rating Application … 6-24 1. Procedures for Completing FAA Form 8610-2 … 6-24 2. Privacy Act … 6-25 3. Complete the Top Section … 6-25 4. Block I—Applicant Information … 6-26 5. Block II—Certificate or Rating Applied for on Basis of — … 6-29 6. Block III—Record of Experience … 6-32 7. Block IV—Applicant’s Certification … 6-34 8. Block V—I Find This Applicant Meets the Experience Requirements of 14 CFR Part 65 and is Eligible to Take the Required Tests … 6-35 9. For FAA Use Only … 6-36 10. Results of Oral and Practical Tests … 6-36 11. Designated Examiner’s Report … 6-37 12. Applicant’s Certification … 6-37 13. FAA Inspector’s Report … 6-38 6-2A. FAA Form 8610-2, Airman Certificate and/or Rating Application … 6-39 6-2B. FAA Form 8610-2, Airman Certificate and/or Rating Application … 6-40 6-2C. Attachment for FAA Form 8610-2, Airman Certificate and/or Rating Application … 6-41 6-2D. FAA Form 8610-2, Airman Certificate and/or Rating Application … 6-42 6-2E.

FAA Form 8610-2, Airman Certificate and/or Rating Application … 6-43 6-2F. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) … 6-44 6-2G. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) … 6-45 6-2H. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) … 6-46 6-2I. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) … 6-47 6-2J. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) … 6-48 6-2K. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) … 6-49 6-2L. FAA Form 8060-4, Temporary Airman Certificate … 6-50 6-2M. FAA Form 8060-4, Temporary Airman Certificate … 6-51 6-2N. Example Statement of Additional Instructions … 6-52 6-2O. Airman Computer Test Report for Aviation Mechanic Airframe (AMA) … 6-53 6-3A. FAA Form 8610-2, Airman Certificate and/or Rating Application (Front Side) … 6-54 6-3B. FAA Form 8610-2, Airman Certificate and/or Rating Application (Front Side) … 6-55 6-3C.

FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) … 6-56 6-3D. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) … 6-57

viii

List of Figures (Continued) Figure Page

6-3E. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) … 6-58 6-3F. Example Statement of Additional Instruction … 6-59 6-3G. Airman Computer Test for Parachute Rigger … 6-60 6-3H. FAA Form 8060-4, Temporary Airman Certificate … 6-61 6-3I. FAA Form 8060-4, Temporary Airman Certificate … 6-62 6-3J. FAA Form 8060-4, Temporary Airman Certificate … 6-63 6-4A. Airframe and Powerplant Mechanical Oral and Practical Planning Sheet (Front Side) … 6-64 6-4B. Airframe and Powerplant Mechanic Oral and Practical Planning Sheet (Reverse Side) … 6-65 6-4C. Parachute Rigger Oral/Practical Test Planning Sheet … 6-66 7-1. Specific Eligibility Requirements for Sport Pilot Examiners … 7-4 7-2. Specific Eligibility Requirements for Pilot Examiner Designees … 7-6 7-3. Specific Eligibility Requirements for Commercial Pilot Examiner Designees … 7-7 7-4. Specific Eligibility Requirements for Commercial and Instrument Rating Examiner and Airline Transport Pilot Examiner Designees … 7-8 7-5. Vintage Airplane Groups … 7-14 7-6.

List of Figures (Continued)

ICAO Level 4 English Language Proficiency Criteria … 7-171 7-7. Sample FAA Form 8410-1, Airman Proficiency/Qualification Check … 7-172 7-8A. Pilot Examiner Test Guide (First Page) … 7-173 7-8B. Pilot Examiner Test Guide (Second Page) … 7-175 7-8C. Sport Pilot Examiner Test Guide (First Page) … 7-176 7-8D. Sport Pilot Examiner Test Guide (Second Page) … 7-177 7-8E. Sport Pilot Examiner Test Guide (Third Page) … 7-178 7-8F. Sport Pilot Examiner Test Guide (Fourth Page) … 7-179 7-8G. Sport Pilot Examiner Test Guide (Fifth Page) … 7-180 7-9A. Sample Letter of Discontinuance (Pilot) … 7-181 7-9B. Sample Letter of Discontinuance (Sport Pilot) … 7-182 7-10. Sample Computer Test Report (Pilot) … 7-183 7-10A. Sample of Computer Test Report (Sport Pilot) … 7-184 7-11. Letter from Part 141 School with Knowledge Test Examining Authority … 7-185 7-12. Sample of FAA Form 8710-11, Airman Certificate and/or Rating Application— Sport Pilot (Front Side) … 7-186 7-12A. Sample of FAA Form 8710-11, Airman Certificate and/or Rating Application— Sport Pilot (Reverse Side) … 7-187 7-13.

Sample FAA Form 8060-4, Temporary Airman Certificate (Pilot) … 7-188 7-13A. Sample FAA Form 8060-4, Temporary Airman Certificate (Sport Pilot) … 7-189 7-14. Center Thrust Limitation … 7-190 7-15. Sample FAA Form 8060-5, Notice of Disapproval of Application (Pilot) … 7-191 7-15A. Sample FAA Form 8060-5, Notice of Disapproval of Application (Sport Pilot) … 7-192

ix

List of Figures (Continued) Figure Page

7-16. Sample Application for a Part 141 Stage Check … 7-193 7-17. Sample FAA Form 8420-2, Medical Certificate____ Class and Student Pilot Certificate … 7-194 7-18. Sample Student Pilot Certificate … 7-195 7-19. Sample Recreational Pilot Certificate … 7-196 7-20. Sample Private Pilot Certificate with Recreational Pilot Category Privileges … 7-197 7-21. Sample Commercial Pilot Certificate … 7-198 7-22. Sample ATP Certificate with Instrument Privileges Shown … 7-199 7-23. Sample Second-in-Command Limitation … 7-200 7-24. Sample Gold Seal Flight Instructor Certificate (Pilot) … 7-201 7-24A. Sample Gold Seal Flight Instructor Certificate with a Sport Pilot Rating … 7-202 7-25. Verification of Authenticity Form and Instructions … 7-203

x

Chapter 1. General Information › 4. What This Order Cancels.

Chapter 1. General Information

1. Purpose of This Order. This order provides policy and mandatory standardized procedures for those who administer all aviation mechanic, parachute rigger, or pilot oral and practical tests and issue temporary airman certificates. This order does not apply to check airmen/check pilots and Aircrew Designated Examiners (ADE) serving in programs approved under Title 14 of the Code of Federal Regulations (14 CFR) parts 91 subpart K, 121, 125, and 135. It also does not apply to Training Center Evaluators (TCE) who serve at training centers certificated under 14 CFR part 142. Compliance with these standardized procedures ensures that airman applicants meet a satisfactory level of competence and workmanship required for certification. This order does not relieve Federal Aviation Administration (FAA) personnel from instructing and guiding designees.

a. General Aviation Airman Designees. This order includes FAA policy emphasizing the general aviation airman designee’s (referred to in this order as designee or examiner) knowledge of oral and practical tests, as well as the administration of airman knowledge tests; it also concerns the administration of such tests and the issuance of airman certificates. For the purposes of this order, designee refers to Technical Personnel Examiners (TPE) and Designated Pilot Examiners (DPE). TPE will refer only to Designated Mechanic Examiners (DME) and Designated Parachute Rigger Examiners (DPRE). DPE will refer only to Private Pilot Examiners (PE), Commercial and Instrument Rating Examiners (CIRE), Commercial Pilot Examiners (CE), Airline Transport Pilot Examiners (ATPE), Flight Instructor Examiners (FIE), National Designated Pilot Examiner and Flight Engineer Examiners (NDPE/FEE), Sport Pilot Examiners (SPE), and Sport Pilot Flight Instructor Examiners (SFIE), and Pilot Proficiency Examiners (PPE), as well as pilot examiners with administrative privileges only including Airman Certification Representatives (ACR), Flight Instructor Renewal Examiners (FIRE), Foreign Pilot Examiners (FPE), Ground Instructor Examiners (GIE), Military Competency Examiners (MCE), and Military Competency/Foreign Pilot Examiners (MC/FPE).

b. Guidance Questions. While the Flight Standards Service (AFS) Regulatory Support Division (AFS-600) coordinated this consolidated handbook, questions regarding the specific guidance relating to each type of designee should be directed to the policy division that owns the policy for that type of designee. Please refer to the chart below for any questions:

Designee Type Policy Holder TPE AFS-300 DPE AFS-810 or AFS-610 (SPE/SFIE)

2. Audience. The primary audience is designees responsible for administering oral and practical tests and issuing temporary airman certificates.

3. Where You Can Find This Order. Designees and inspectors can access this order through the Flight Standards Information Management System (FSIMS) at http://fsims.avs.faa.gov.

4. What This Order Cancels. This order cancels FAA Order 8610.12, Technical Personnel Examiner Handbook, dated July 14, 2008; FAA Order 8710.3E (and FAA Order 8710.3E

8. Definitions. › a. Airmen Certification Branch (AFS-760). AFS-760, which is part of the…

CHG 1), Designated Pilot and Flight Engineer Examiner’s Handbook, dated April 21, 2006; and FAA Order 8710.7, Sport Pilot Examiner’s Handbook, dated October 14, 2004.

5. Explanation of Policy Changes. This change incorporates information updated in accordance with the publication of the Pilot Certification and Qualification Requirements for Air Carrier Operations final rule. These changes include the following:

a. Verification of an Applicant’s Identity. This change refers designees to FAA Order 8900.1, Volume 5, Chapter 1, Section 3 for guidance and procedures associated with the verification of an applicant’s identity.

b. Illegal Substance Conviction. This change refers designees to FAA Order 8900.1, Volume 5, Chapter 1, Section 3 for guidance and procedures associated with the completion of FAA Form 8710-1.

c. Completion of FAA Form 8710-1. This change refers designees to FAA Order 8900.1, Volume 5, Chapter 1, Section 3 for guidance and procedures associated with the completion of FAA Form 8710-1.

d. Conduct an Airline Transport Pilot (ATP) Certification, Including Additional Category/Class Ratings at the ATP Certification Level. This change refers designees to FAA Order 8900.1, Volume 5, Chapter 2, Section 18 for tasks associated with conducting an ATP certification, including additional category/class ratings at the ATP certificate level.

e. Procedures for Issuing a Second-in-Command (SIC) Pilot Type Rating. This change refers designees to FAA Order 8900.1, Volume 5, Chapter 2, Section 5 for completeing the certification function.

6. Delegation/Rescission of a Designee Authorization. Title 49 of the United States Code (49 U.S.C.) § 44702 empowers the FAA Administrator to delegate to private individuals any function relating to the examination, inspection, and testing of airman applicants.

7. Role of the Designee. Designees have been an important part of the FAA’s support to the flying public for over 60 years. During that time, designees successfully completed thousands of certification activities on the FAA’s behalf. The designee function is vital to enhancing the FAA’s public service role and enhancing overall safety in the National Airspace System (NAS). The FAA and its designees are in a symbiotic relationship. The FAA appoints designees to leverage its workforce and provide certification services to the public, and the designee provides certification services to the public in accordance with FAA policy and guidance. One component of this relationship involves how the FAA views the designee, as well as how the designee views the FAA.

8. Definitions. This paragraph contains definitions for FAA offices, FAA forms, and terms commonly used in this order. Appendix A contains a list of acronyms used in this order.

a. Airmen Certification Branch (AFS-760). AFS-760, which is part of the FAA Civil Aviation Registry, has final authority for the issuance of permanent airman certificates and

maintenance of certification records. AFS-760 is located at the Mike Monroney Aeronautical Center (MMAC) in Oklahoma City, OK.

8. Definitions. › j. Designated Pilot Examiner (DPE). A DPE is an individual, appointed…

b. Airmen Medical Certificate. An airmen medical certificate is a valid certificate issued under 14 CFR part 67, Medical Standards and Certification.

c. Aviation Maintenance Technician School (AMTS). An FAA-approved school for aviation mechanics. Graduation from the appropriate course of a certificated AMTS is one way for mechanic applicants to meet the experience requirement.

d. Aviation Safety Inspector (ASI). An FAA employee with the necessary technical qualifications who is responsible for developing, administering, investigating and enforcing safety regulations for airmen, aircraft and aircraft operations. In most cases, ASIs are also responsible for the oversight of designees.

e. Aviation Safety Technician (AST). An FAA employee who provides technical support and assistance to ASIs.

f. Certification and General Aviation Operations Branch (AFS-810). AFS-810, which is part of the General Aviation and Commercial Division (AFS-800), is the principal office concerned with the certification and training of airmen (pilots, ground, and flight instructors). AFS-810 is responsible for DPE policy, with the exception of SPE policy.

g. COA Letter. A COA letter is issued to each Flight Standards general aviation designee to specify their authority and appropriate limitations for a given appointment period.

Note: FAA Form 8430-9 and LOAs are no longer issued, but may remain in effect until expiration, unless surrendered or terminated before that time.

h. Designated Mechanic Examiner (DME). A DME is an individual, appointed in accordance with 14 CFR part 183, § 183.25, who holds a valid aviation mechanic certificate, possesses technical knowledge and experience required for aviation mechanic certification, and meets the general qualification requirements set forth in chapter 2 and the TPE-specific qualifications set forth in chapter 6.

i. Designated Parachute Rigger Examiner (DPRE). A DPRE is an individual, appointed in accordance with § 183.25, who has a high level of knowledge in the subject areas required for parachute rigger certification, holds a master parachute rigger certificate for the particular designation, and meets the general qualification requirements set forth in chapter 2 and the TPE-specific qualifications set forth in chapter 6.

j. Designated Pilot Examiner (DPE). A DPE is an individual, appointed in accordance with § 183.23, who meets the general qualification requirements set forth in chapter 2 and the DPE-specific qualifications set forth in chapter 7. For the purposes of this order, a DPE is a PE, CIRE, CE, ATPE, FIE, PPE, NDPE/FEE, SPE, or SFIE. In addition, a DPE is an examiner with administrative privileges for which there are the ACR, FIRE, FPE, GIE, MCE, and MC/FPE.

8. Definitions. › v. FAA Form 8710-2, Student Pilot Certificate. FAA Form 8710-2 is…

k. Designee. Designee is the general term used in this order to describe a representative of the FAA Administrator authorized by law and appointed in accordance with the applicable provisions of § 44702 or part 183, Representatives of the Administrator, to examine, test, and/or make inspections necessary to issue airman or aircraft certificates. For the purposes of this order, designee refers to individual examiner designations including TPEs, and DPEs.

l. Designee Quality Assurance Branch (AFS-650). AFS-650, which is part of AFS-600, collects National Examiner Board (NEB) application materials from designee applicants.

m. Designee Standardization Branch (AFS-640). AFS-640, which is part of AFS-600, develops and conducts a variety of standardization seminars both domestically and internationally that are used by designees, designee applicants, representatives of delegations, and FAA personnel for initial training and renewal purposes.

n. Experimental Aircraft Association (EAA). EAA is an international organization of aviation enthusiasts interested in flying, building, and restoring recreational aircraft. EAA considers application materials submitted by NDPE/FEE applicants and recommends successful examiner candidates to AFS-800.

o. FAA Form 8000-5, Certificate of Designation. FAA Form 8000-5 is a certificate issued to a designee by the FAA office manager authorizing the designee privileges.

p. FAA Form 8060-4, Temporary Airman Certificate. FAA Form 8060-4 is a temporary airman certificate issued to a successful airman applicant.

q. FAA Form 8060-5, Notice of Disapproval of Application. FAA Form 8060-5 is issued by a DPE to an unsuccessful airman applicant.

r. FAA Form 8110-28, Application and Statement of Qualification (DME/DPRE/DAR-T/ODAR-T). FAA Form 8110-28 is the application used by TPE applicants for appointment and renewal.

s. FAA Form 8420-2, Medical Certificate … Class and Student Pilot Certificate. FAA Form 8420-2 is issued to an airman applicant who meets the requirements for a student pilot certificate by an Aviation Medical Examiner (AME) and serves as both a medical certificate and a student pilot certificate.

t. FAA Form 8610-2, Airman Certificate and/or Rating Application. FAA Form 8610-2 is used by mechanic and parachute rigger applicants when applying for an airman certificate and/or rating.

u. FAA Form 8710-1, Airman Certificate and/or Rating Application. FAA Form 8710-1 is used by pilot applicants (other than sport pilot applicants) when applying for an airman certificate and/or rating.

v. FAA Form 8710-2, Student Pilot Certificate. FAA Form 8710-2 is issued to a qualified student pilot applicant.

8. Definitions. › ii.

w. FAA Form 8710-10, National Examiner Board-Designated Pilot Examiner Candidate Application. FAA Form 8710-10 is the application used by DPE applicants (other than SPE/SFIE applicants) to submit to the NEB or managing Flight Standards District Office (FSDO) or International Field Office (IFO), as applicable.

x. FAA Form 8710-11, Airman Certificate and/or Rating Application – Sport Pilot. FAA Form 8710-11 is used by sport pilot applicants when applying for an airman certificate and/or rating.

y. FAA Form 8710-12, Light-Sport Standardization Board-Designated Pilot Examiner Candidate Application. FAA Form 8710-12 is the application used by SPE/SFIE applicants to submit to the NEB.

z. Flight Instructor Refresher Clinic (FIRC). FIRCs provide a method by which instructors can renew their instructor certificates.

aa. Flight Standards District Office (FSDO). As used in this order, the FSDO is the office that has jurisdiction over the geographic area in which the designee is located.

bb. General Aviation & Commercial Division (AFS-800). AFS-800 is the FAA AFS division responsible for developing national policies, standards, systems, procedures, and programs for general aviation and advising senior FAA management on general aviation matters. AFS-800 is also responsible for developing standards, policies, and procedures for appointing private individuals to represent the FAA Administrator for the certification of airmen.

cc. Integrated Airman Certification and/or Rating Application (IACRA). The IACRA system is an Internet-based (paperless) method of processing airman applications.

dd. International Field Office (IFO). As used in this order, the IFO is the office that has jurisdiction over the international geographic area in which the designee is located.

ee. Light Sport Aviation Branch (AFS-610). AFS-610, which is part of AFS-600, manages and provides oversight of the SPE and the light sport aircraft repairman-training programs. AFS-610 is responsible for SPE/SFIE policy.

ff. National Examiner Board (NEB). A board convened to oversee the designee application and screening process for AFS.

gg. Regulatory Support Division (AFS-600). AFS-600 promotes safety by educating and advising users through the development, implementation, analysis and distribution of technical information including airmen testing, designee standardization, and management of aviation data systems.

hh. Scenario-Based Training (SBT). A training system that uses a highly structured script of real-world experiences to address flight-training objectives in an operational environment.

ii. Technical Personnel Examiner (TPE). For the purposes of this order, TPE will refer to only DMEs and DPREs.

(1) Designee applicants must complete an application package and submit… › (a) Technical Personnel Examiner (TPE).

Chapter 2. Selection and Appointment

1. Selection.

a. Application. The managing Federal Aviation Administration (FAA) office selects applicants for a designee appointment. When selecting approved candidates, the managing FAA office considers the recommendations from knowledgeable members of the aviation community. The National Examiner Board (NEB), or other evaluating entity, receives applications and will review designee applicants for the general eligibility requirements set forth in paragraph 3.

(1) Designee applicants must complete an application package and submit it to the NEB for review and consideration. Address the application package to: FAA, National Examiner Board, Attn: Designee Quality Assurance Branch (AFS-650), P.O. Box 25082, Oklahoma City, OK 73125-0082. Applicants should retain a copy of all application documents submitted to the FAA.

Note: Candidates for designation as an Airman Certification Representative (ACR), Flight Instructor Renewal Examiner (FIRE), Foreign Pilot Examiner (FPE), Ground Instructor Examiner (GIE), Military Competency Examiner (MCE), Military Competence/Foreign Pilot Examiner (MC/FPE), or Pilot Proficiency Examiner (PPE) must send their completed application forms directly to the managing Flight Standards District Office (FSDO) or International Field Office (IFO) for processing. Candidates holding ACR, FIRE, FPE, GIE, MCE, MC/FPE, or PPE designations who are applying for designation as any other type of Designated Pilot Examiner (DPE) must submit an application for examiner authorization to the NEB.

Note: National Designated Pilot Examiner and Flight Engineer Examiner (NDPE/FEE) candidates must already possess an active DPE before submitting an NDPE/FEE application directly to the Experimental Aircraft Association (EAA) for consideration. The EAA will recommend successful examiner candidates to the FAA, General Aviation and Commercial Division (AFS-800), 800 Independence Avenue S.W., Washington, DC 20591 for selection and appointment.

Note: Current FAA employees will not be appointed as designees until their employment with the FAA has ended. FAA employees may not apply to the NEB earlier than 120 calendar-days before their actual date of retirement or separation from the agency. A letter of recommendation must accompany the application from management of their last assigned office. Appointments will be limited to functions performed while employed by the FAA, or other experience within the aviation industry. If a former FAA employee submits an application beyond 3 years from the date of separation, all application requirements apply.

(a) Technical Personnel Examiner (TPE). All TPE applicants must complete FAA Form 8110-28, Application and Statement of Qualification (DME/DPRE/DAR-T/

ODAR-T). The application package must also include legible copies of the applicable airman certificates held by the examiner candidate.

(1) Determining Need. › (a) Activity level of designees performing similar work in managing FAA…

(b) DPE. DPE applicants, other than Sport Pilot Examiner (SPE)/Sport Pilot Flight Instructor Examiner (SFIE) applicants, must complete FAA Form 8710-10, National Examiner Board-Designated Pilot Examiner Candidate Application. SPE/SFIE applicants must complete FAA Form 8710-12, Light-Sport Standardization Board-Designated Pilot Examiner Candidate Application. The application package must include a legible copy of airman and flight instructor certificates held by the examiner candidate, and a copy of the examiner candidate’s valid medical certificate (at least third-class), if appropriate.

(2) The NEB will review designee applicants (with the exception of ACR, FIRE, FPE, GIE, MCE, MC/FPE, NDPE/FEE, or PPE applicants) for the applicable criteria in this order and rank the applicants against the other applicants who meet those requirements. The NEB will notify the applicant (by letter) of the results.

Note: If the NEB determines that a designee candidate is not qualified, the NEB Recorder will retain the candidate’s application file for 4 calendar-months from the month of the evaluation, pending an appeal or request for additional information. At the end of the 4th calendar-month, the NEB Recorder will transfer the designee candidate’s application file to the NEB’s electronic database and discard the paper copies of the application file.

(3) The appointing FAA office will notify the NEB when it has determined a need for, and possesses the ability to manage a designee.

(4) The appointing FAA office will notify the candidate, and the candidate will schedule himself or herself to attend an initial training seminar. After the candidate successfully completes the initial training seminar, the candidate will provide the appointing FAA office with the certificate of completion from the initial training seminar.

Note: Candidates must successfully complete the initial training seminar before appointment as a designee. The initial training seminar is valid for up to 12 calendar-months prior to appointment. If the candidate is not appointed within the 12 calendar-month period, he or she must retake the initial training seminar. Once appointed, the recurrent training seminar is due on the established seminar interval for the designee type (24 or 36 months) from completion of the initial training seminar.

b. Need for and Ability to Manage a Designee. Successfully meeting the eligibility requirements does not guarantee appointment as a designee. The managing FAA office, within its sole discretion, determines the need for and ability to manage a designee.

(1) Determining Need. The managing FAA office considers several factors in determining the need for a designee including, but not limited to:

(a) Activity level of designees performing similar work in managing FAA office’s geographical area.

2. Appointment. › c. Serve Outside the United States. A designee may be appointed to…

(b) Demand/convenience to the public as determined by the:

• Ability to provide examinations within a reasonable period of time, and • Number of complaints from the public for lack of availability of certification.

(c) Geographic dispersion as determined by the distance the applicant must travel to get to designee.

Note: Need for a new designee is driven by the needs of the public and not by the impact on other existing designees or the desires of air operators/agencies.

(2) Determining the Ability to Manage. The managing FAA office reviews several criteria to determine the ability to manage a designee including, but not limited to:

(a) Effect of workload on inspectors,

(b) Funding (e.g., travel allocation) needed to oversee the designee workforce, and

(c) Availability of trained inspectors (specialists) and/or managers.

2. Appointment. The appointing FAA office will complete FAA Form 8000-5, Certificate of Designation, and a certificate of authority (COA) letter for presentation to the designee.

Note: The act of signing the designee application (see table below), is an acknowledgment that the designation is a privilege, not a right, and the FAA Administrator can terminate any designation at any time or for any reason he or she deems appropriate.

a. Applying for Reinstatement. Reinstatement is used in instances where a former designee is applying for privileges, after the termination of his or her designation, to the last managing FAA office that previously had jurisdiction over the designee. Former designees wishing to apply for reinstatement must submit the completed application directly to the designating FAA office and are not required to apply to the NEB if they previously held the same type of designation. The FAA office, in its sole discretion, will determine if there remains a need for the examiner, and if it possesses the ability to manage the examiner as set forth in subparagraph 1b above. The former designee must meet the applicable training requirements set forth in this order.

b. Applying for Relocation. Designees may relocate to a different geographical area, and the receiving FAA office agrees to the transfer, without applying to the NEB. The designee must submit a new application to the receiving FAA office.

c. Serve Outside the United States. A designee may be appointed to serve outside the United States provided there is a demonstrated need that such designation will serve U.S. citizens abroad and an FAA office can properly supervise the designee’s activities. The designee is subject to limitations as provided by current FAA policy regarding the certification of airmen outside the United States.

3. General Eligibility Requirements. › h. Technology Access. Have internet access, as well as access to a…

Note: Although the intent of the designee is to serve U.S. citizens abroad, this does not preclude the designee from serving non-U.S. citizens.

3. General Eligibility Requirements. Inspectors must carefully consider all of the following issues before designating or renewing an examiner. Additional eligibility requirements for specific designee types are included in the applicable designee component chapter (chapter 6 (TPE), and chapter 7 (DPE)). The general requirements for appointment, which are reviewed by the NEB, are:

a. Minimum Age. Minimum age of 23 years for all designees.

b. Personality Traits. Have integrity, professionalism, and sound judgment.

c. Training Requirement. Have satisfactorily completed the applicable training requirement before appointment/renewal as a designee.

d. Knowledge of Guidance Materials. Have good knowledge of the pertinent regulations, directives, and related guidance material.

e. Command of English Language. Have command of the English language—spoken and written.

f. Objectivity. Have the ability to maintain the highest degree of objectivity while performing authorized functions.

g. Good Record. Have a good record in the aviation industry.

h. Technology Access. Have internet access, as well as access to a computer and printer with hardware/software sufficient to support the required activities.

Note: An examiner is not required to be a U.S. citizen.

Note: Applicants should provide enough detail in their application packages to allow the NEB to determine that they meet the general requirements of Chapter 3 as well as those requirements specific to the applicable designee type (Chapter 6 for TPEs or Chapter 7 for DPEs).

Chapter 3. Oversight, Training, and Renewal › 3. Orientation.

Chapter 3. Oversight, Training, and Renewal

1. Oversight. Each designee operates under the direct supervision of the Federal Aviation Administration (FAA) office that holds the designation file, referred to as the managing FAA office. Supervision of designees includes the following functions:

a. Resolve Questions. Inspectors or FAA personnel who supervise the activities of designees must always welcome the opportunity to discuss procedures and standards with designees upon request to resolve any questions. Designees should direct any questions to their managing FAA office.

b. Observe and Provide Oversight. Technical Personnel Examiners (TPE) and Designated Pilot Examiners (DPE) should expect the FAA to observe them conducting their first complete tests. Thereafter, the examiner may be inspected or observed by FAA personnel at any time with or without prior notice.

c. Document and Submit Certification Files. DPEs must submit certification files to the managing FAA office regardless of test results (pass or fail) within 7 calendar-days of the test date. TPEs must submit certification files to the managing FAA office regardless of test results (pass, fail, or incomplete) within 7 calendar-days of the test date.

d. Check Knowledge and Accuracy of Certification Files. A critical component of the certification process is the accuracy of the certification files. The managing FAA office may check the designee’s aeronautical knowledge and certification procedures at any time.

2. Initial Training Seminar. Before designation, prospective examiners must satisfactorily complete the initial standardization seminar.

Designee Type Initial Training Requirement TPE Initial TPE Standardization Seminar DPE Initial Pilot Examiner Standardization Seminar

Note: Information regarding designee standardization training seminars is available on the Designee Registration System Web site at https://av-info.faa.gov/DsgReg/default.aspx.

Note: Currently, initial training for certain designee types including Airman Certification Representative (ACR), Flight Instructor Renewal Examiner (FIRE), Foreign Pilot Examiner (FPE), Ground Instructor Examiner (GIE), Military Competency Examiner (MCE), Military Competency/Foreign Pilot Examiner (MC/FPE), or Pilot Proficiency Examiner (PPE) applicants is conducted by the managing FAA office.

3. Orientation. Following the initial training seminar, personnel from the managing FAA office will coach the examiner in all procedures relevant to the designee’s duties before the designee conducts any tests. The assigned inspector or FAA personnel from the managing FAA office must be present during the first tests administered by the designee to provide guidance and

Chapter 3. Oversight, Training, and Renewal › 5. Expiration.

training, and to inform the designee of the proper test procedures. Specific items of emphasis during the orientation are:

a. Direction and Guidance. The designee is expected to call upon the managing FAA office for advice and guidance, as necessary, for the performance of assigned responsibilities in accordance with prescribed procedures.

b. Reference Materials. The designee is expected to have ready access to the current rules, policy, and technical data appropriate to airman certification and/or the administration of airman knowledge tests, as applicable.

c. Instruction. The designee must receive specific instructions from the managing FAA office in the proper conduct of his or her authorized functions.

d. Non-Discrimination. The designee is expected to make his or her services available to all applicants on an equitable basis regardless of who trained the applicant or the applicant’s geographic area of residence.

e. Eligibility Requirements. The designee is expected to understand the continuing general eligibility requirements as set forth in chapter 2, paragraph 3.

4. Recurrent Training. Each designee is encouraged to attend safety meetings, aviation seminars, and other programs that contribute to the technical skills required for the designation. Designees must schedule themselves for a recurrent training seminar and notify the managing FAA office. Examiners must satisfactorily complete the initial training seminar prior to enrollment in the recurrent training seminar. Attendance at a recurrent training seminar is mandatory. The Certificate of Completion issued to those that successfully complete a recurrent training seminar will expire in the specified time period (see below) from the date shown on the certificate. The designee must forward a copy of the Certificate of Completion to the managing FAA office. The recurrent training requirements are set forth below:

Designee Type Recurrent Training Requirement TPE 24 calendar-months – Recurrent TPE Standardization Seminar DPE with the exception of: ACR, FIRE, FPE,

GIE, MCE, MC/FPE, or PPE

24 calendar-months – Recurrent Pilot Examiner Standardization Seminar ACR, FIRE, FPE, GIE, MCE, or MC/FPE 36 calendar-months – Administrative Pilot Examiner Standardization Seminar

Note: Examiners may complete the initial training seminar in lieu of the recurrent training seminar to meet the recurrent training requirement set forth in chapter 3, paragraph 4.

Note: An examiner will not exercise his or her designation privileges unless his or her training is current and up-to-date.

5. Expiration. Initial appointment is for a period of 1 year. After the initial appointment period, the managing FAA office will determine the duration of the designation. The duration of the

d. Renewal Application Package. The designee must apply for renewal to… › (4) Additional application materials (as indicated below):

designation cannot exceed 3 years. The expiration date appears on the certificate of authority (COA) letter, which each designee receives.

6. Renewal. A designee may be renewed if the continuation of the designation is justified, and the designation is in the FAA’s interest. The designee is responsible for submitting a timely renewal package. The FAA office must notify the designee that renewal has occurred and issue a new COA letter. A designation will be renewed under the following conditions:

• The managing FAA office determines that a need still exists; • The FAA office still has the ability to manage the designee; and • The designee continues to meet the eligibility requirements in chapter 2, paragraph 3 and the specific requirements listed in the applicable designee component chapter.

a. Annual Meeting. The designee must attend an annual meeting held by the managing FAA office to discuss designee procedures, problems, and designation renewal.

Note: Based on a program level risk analysis, the managing FAA office may exempt the following designee types from the annual meeting requirement: ACRs, FIREs, FPEs, GIEs, MCEs, MC/FPEs, and PPEs.

b. Designee Maintains Designation. When conducting tests, each designee must maintain the applicable airman certificate(s), the general eligibility requirements listed in chapter 2, paragraph 3 and the specific eligibility requirements in the designee component chapter (chapter 6 (TPE), and chapter 7 (DPE)).

c. Training Requirements. The recurrent training requirements in chapter 3, paragraph 4 must be completed.

d. Renewal Application Package. The designee must apply for renewal to the managing FAA office at least 45 calendar-days before the expiration of the designation. It is the responsibility of the designee to complete the renewal application package. The package must include:

(1) A copy of the designee’s current COA letter or previously issued FAA Form 8430-9, Certificate of Authority;

(2) A record of all designee activity conducted since the issuance or last renewal of their designation;

(3) A current certificate of training showing the designee has successfully completed an initial or recurrent training seminar; and

(4) Additional application materials (as indicated below):

Chapter 3. Oversight, Training, and Renewal › 7. Knowledge and Skill.

Designee Type Renewal Application Requirements TPE FAA Form 8110-28 with blocks 1, 2, 4, 5, 6, 7, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 22, 23, and 23a completed. (The managing FSDO or IFO will approve the application for renewal by completing applicable blocks on the FAA application form. DPE A letter from the DPE requesting renewal and the designation(s) the examiner is requesting to be renewed. The letter must include this acknowledgment language: “THIS DESIGNATION IS A PRIVILEGE, NOT A RIGHT, AND THE FAA ADMINISTRATOR CAN TERMINATE ANY DESIGNATION AT ANY TIME OR FOR ANY REASON HE OR SHE DEEMS APPROPRIATE.” A copy of the DPE’s current pilot, flight instructor, and airman medical certificate, with the exception of a GIE applicant.

e. COA Letter. After expiration of the designee’s COA letter, the designee may not exercise the privileges of the designation unless he or she has a current COA letter signed by the managing FAA office and the designee.

7. Knowledge and Skill. The determination that the designee’s knowledge of and application of current procedures and standards are adequate for renewal of the designation may be based on oversight of the designee and the designee’s attendance at a meeting or seminar conducted for the purpose of standardization.

4. Appeal. › d. Written Notification. The designee will be notified in writing of…

Chapter 4. Termination and Appeal

1. Termination. Termination is the action by the Federal Aviation Administration (FAA) to rescind a designation at any time for any reason the Administrator considers appropriate.

2. Types of Termination.

a. Termination for Cause. Termination for cause is a negative finding based on a designee’s performance.

b. Termination Not-for-Cause. Termination not-for-cause can be for any reason not specific to a designee’s performance (e.g., lack of need for the designee or ability to manage the designee by the FAA office).

Note: A designee may voluntarily surrender a designation at any time. This voluntary surrender should be made in writing, sent to the appointing FAA office manager and be accompanied by the designee’s certificate of authority (COA) letter or previously issued FAA Form 8430-9, Certificate of Authority.

3. Termination Letter. Designations are terminated under the general conditions contained in Title 49 of the United States Code (49 U.S.C.) § 44702. The appointing FAA office manager makes the decision to terminate a designee. The FAA office manager’s decision regarding the termination of a designation will be provided to the designee in writing, and the reasons cited will be as specific as possible. Upon receipt of a termination letter, the designee must immediately cease the exercise of his or her designee privileges.

4. Appeal. The designee or designee applicant may request an appeal. (Reference: FAA Order 8900.1, Flight Standards Information Management System (FSIMS), Volume 13, Chapter 5, Section 3, Termination and Appeal.)

a. Appeal of Non-Selection/Non-Appointment. The National Examiner Board (NEB) handles appeals of non-selection. Contact the Designee Standardization Branch (AFS-650) with questions. Appeal of non-appointment initiates at the local office, which will handle the appeal in accordance with the appeal of termination process in Order 8900.1, Volume 13, Chapter 5, Section 3.

b. Non-Appeal Termination. Termination based on the lack of need, the inability of the FAA office to manage the examiner, loss of a prerequisite certification, or failure to meet training requirements cannot be appealed.

c. Written Termination Appeal. If the designee wishes to appeal his or her termination, the designee must make the request in writing within 14 calendar-days of receipt of the written notification of the FAA office manager’s decision to the regional appeal panel by sending a letter to the FAA office manager requesting an appeal.

d. Written Notification. The designee will be notified in writing of the appeal panel’s decision within 60 calendar-days.

Note: The regional appeal panel’s decision is final.

e. Designated Pilot Examiners (DPE). DPEs may accept pilot applications… › (2) DPEs may not accept an application for a name change, citizenship…

Chapter 5. Privileges, Limitations, and Responsibilities

1. Privileges. A designee is authorized to:

a. Accept Airman Certificate/Rating Application. Accept applicable airman certificate and/or rating applications for airman certificates and ratings.

Designee Type FAA Form Technical Personnel Examiner (TPE) FAA Form 8610-2 Designated Pilot Examiner (DPE) FAA Form 8710-1 or FAA Form 8710-11

b. Conduct Tests. Conduct tests, in the English language, appropriate to the Federal Aviation Administration (FAA) certificate of authority (COA) letter held by the designee, in accordance with the appropriate practical test standards (PTS).

c. Applicant Fees. Charge each applicant a reasonable fee. The examiner should ensure the applicant understands all fees charged, including the fee for retesting after failure, before the designee accepts the airman certificate and/or rating application.

Note: Use caution to ensure that the TPE is accepting payment from the applicant or on behalf of the applicant and that the designee remains a private person acting as a representative of the Administrator in accordance with Title 14 of the Code of Federal Regulations (14 CFR) part 183, subpart C.

d. Issue Temporary Airman Certificates. Issue temporary airman certificates to applicants who have been tested and found qualified for the certificate or rating sought. The managing FAA office may retain this privilege. This authorization should be listed in the COA.

e. Designated Pilot Examiners (DPE). DPEs may accept pilot applications for new pilot certificates and/or ratings (for which the DPE holds that designation and authority) and any pilot certificate action that is administrative in nature (i.e., second-in-command (SIC) type rating, English language endorsement, etc.), provided the DPE has received training from the supervising Flight Standards District Office (FSDO). DPEs are not authorized to accept medical Statement of Demonstrated Ability (SODA) requests.

(1) If the applicant has a valid verification letter of authenticity and makes an appropriate application, DPEs may accept applications for 14 CFR part 61, § 61.75 pilot certification that are issued on the basis of a foreign pilot license for adding the “English Proficient” endorsement, paper to plastic pilot certificates, as well as replacement of the § 61.75 pilot certificate. Section 61.75 pilot certificate holders will not be able to apply via the web. This requires the applicant to apply in person so there will be positive identification at the time of application to an appropriately authorized DPE, Foreign Pilot Examiner (FPE), FAA aviation safety technician (AST), or FAA aviation safety inspector (ASI). DPEs and FPEs must comply with the guidance in chapter 7, sections 20 and 21.

(2) DPEs may not accept an application for a name change, citizenship change, date of birth change, gender change, dual citizenship, any other changes to personal data, or removal of an English language limitation where the appropriate FAA order already covers a procedure. If

2. Limitations. › i. Applicant Further Study. A designee must not temporarily suspend a…

the guidance in the appropriate FAA order specifically requires a FSDO to handle the applicant, then a DPE may not perform that function. Changes of a personal nature (name change, sex change, removal of the English language limitation, etc.) that specifically require the applicant to perform the certification action at the FSDO must be performed by FSDO personnel.

2. Limitations.

a. Locations. A TPE must not conduct tests at locations not listed as a base of operation on the current COA letter held by the designee, unless authorized by the managing FAA office. A DPE must not conduct tests at locations outside his or her geographically assigned area, unless authorized by the managing FAA office.

b. Computer Knowledge Tests. A designee must not conduct or monitor any portion of computer knowledge tests.

c. Expired Temporary Airman Certificate. A designee must not reissue or amend any expired temporary airman certificate.

d. Permanent Airman Certificate. A designee must not endorse, amend, alter, or issue any permanent airman certificate.

e. Applicable PTS. A designee must not exempt any applicant from the testing requirements in the applicable PTS.

f. Teaching/Testing. A designee must not combine teaching with testing during the testing of an applicant.

g. Proof of Eligibility. A designee must not conduct tests unless an applicant presents proof of eligibility as prescribed in the applicable 14 CFR part (as set forth below):

Designee Type 14 CFR TPE Part 65 DPE Part 61

Note: Additional limitations that are designee type specific are located within each component chapter.

h. Airman Knowledge Test. A designee must not conduct oral and practical tests unless the applicant has passed the required airman knowledge test.

Note: This does not apply to aviation mechanic applicants authorized to test in accordance with 14 CFR part 65, § 65.80 or master parachute rigger applicants that hold a senior certificate.

i. Applicant Further Study. A designee must not temporarily suspend a test to allow the applicant further study, and then continue the same test later.

3. Responsibilities. › d. FAASTeam Seminars/Events. The FAA encourages designees to attend and…

j. Number of Applicants. A designee conducting an oral and/or practical test must not test more than one applicant at a time, unless authorized in his or her COA by the geographically responsible FSDO and in accordance with the procedures and limitations contained in Order 8900.1.

Note: If you are a Designated Mechanic Examiner (DME) that has a valid need to test two applicants at a time, contact your managing FAA office for consideration.

k. Geographical Area. A designee must not test an applicant outside the authorized geographical area. For a DPE, the test must start and conclude within the authorized geographical area. If a designee wants to administer tests outside the geographical area of the managing FSDO or International Field Office (IFO), the designee must:

(1) Request authorization in writing from the managing FSDO or IFO.

(a) Provide the date and address of the testing site in writing.

(b) Make the request in writing at least 3 working days prior to the scheduled activity.

Note: The FSDO or IFO with jurisdiction over the test site may evaluate the facilities, equipment, current publications, and test materials required to conduct a test for the certificate and/or rating(s) sought.

(2) Receive approval in writing from the designee’s managing FSDO or IFO, as appropriate. The managing office will coordinate with the geographical office.

(3) The designee submits the certification file to the designee’s managing office. The FSDO or IFO withjurisdiction over the test location may request copies of any files for tests conducted by the the designee in their area.

l. Language Requirement. A designee must not conduct tests in any language other than English.

3. Responsibilities. Each designee must represent the Administrator in a manner that reflects positively on the FAA.

a. Honor Appointments. Designees should honor appointments made as promptly as possible.

b. Undivided Attention. Designees must give undivided attention to the applicant during the testing period.

c. Private/Confidential Discussion. Designees must assure that discussion following any test is private and is confidential.

d. FAASTeam Seminars/Events. The FAA encourages designees to attend and take part in FAA Safety Team (FAASTeam) seminars and events. The FAA values the participation of examiners as FAASTeam representatives in providing support for safety meetings.

3. Responsibilities. › e. Knowledge and Skill. A designee must maintain a high degree of…

e. Knowledge and Skill. A designee must maintain a high degree of knowledge and skill in the subject areas required for airman certification, evaluation, and testing techniques.

Chapter 6. Technical Personnel Examiner Program

Section 1. General

1. Additional Requirements for Appointment. The procedures contained in this order apply to inspectors and Technical Personnel Examiners (TPE) authorized to conduct aviation mechanic or parachute rigger oral and practical tests and issue temporary airman certificates. TPEs will conduct tests in accordance with the applicable practical test standards (PTS). Inspectors must carefully consider all of the following issues before designating or renewing an examiner. In addition to meeting the general designee eligibility requirements in chapter 2, an examiner candidate must meet the following additional requirements, which will be reviewed by the appointing Federal Aviation Administration (FAA) office:

1. Additional Requirements for Appointment. › b. For Designated Parachute Rigger Examiner (DPRE) Appointment.

a. For Designated Mechanic Examiner (DME) Appointment.

(1) Evidence of a high level of knowledge in the Subject Areas required for aviation mechanic certification in both reciprocating and turbine-engine aircraft.

(2) Held a valid aviation mechanic certificate for 5 years with the rating(s) for which a designation is to be issued. When qualified persons are not available, the managing FAA office manager may reduce the 5-year requirement to 3 years if the prospective designee meets all other requirements, and possesses the required technical qualifications.

(3) Actively exercised the privileges of a valid aviation mechanic certificate for 3 years on U.S.-registered civil aircraft immediately before designation or other aircraft maintenance governed by Title 14 of the Code of Federal Regulations (14 CFR) part 43.

(4) Have a fixed base of operation adequately equipped to support testing in each Subject Area in a required Section for the designation held, and be adequately equipped to support testing of all of the Core Competency elements listed in the PTS under Objective 2 of a Subject Area for the designation sought. This includes both reciprocating and turbine engine aircraft.

(a) The fixed base of operation, equipment, and materials must be adequate for an applicant to demonstrate the basic skills for the certificate and rating sought. The managing FAA office will monitor the status of equipment periodically to ensure compliance.

(b) Use airworthy aircraft, other aircraft, aircraft subassemblies, operational mockups, or other aids for testing airman applicants.

(c) Tools, equipment, current publications, materials, etc., required to complete a project assignment must be the type recommended by aircraft manufacturers or accepted in the aviation industry.

Note: The DME will be required by the managing field office to report any significant change in the equipment or materials available to test applicants.

b. For Designated Parachute Rigger Examiner (DPRE) Appointment.

(1) Evidence of a high level of knowledge in the Areas of Operation required for parachute rigger certification.

Section 1. General › 3. Parachute Rigger Tests.

(2) Held a valid master parachute rigger certificate for 2 years with the rating(s) for which the managing FAA office will issue a designation.

(3) Actively exercised the privileges of a valid master parachute rigger certificate for 2 years immediately before the designation.

(4) Have a fixed base of operation adequately equipped to support testing in each required Area of Operation for the designation held.

(a) The fixed base of operation, equipment, and materials must be adequate for an applicant to demonstrate the basic skills for the certificate and rating sought. The managing FAA office will periodically monitor the status of equipment to ensure compliance.

(b) Tools, equipment, current publications, materials, etc., required to complete a project assignment must be the type parachute manufacturers recommend or accept in the industry.

(c) The fixed base of operation must, as a minimum, have tools and equipment necessary to perform, in each required Area of Operation, the Tasks the DPRE will assign as part of his or her developed test.

Note: The DPRE will be required by the managing field office to report any significant change in the equipment or materials available to test applicants.

2. Aviation Mechanic Tests. The test standards are contained in three separate booklets, which consist of knowledge (oral question) elements and skill (practical project) elements in each of the five sections. Each section has from 3 to 12 Subject Areas. Section I, General, is required for either the airframe or powerplant rating and applies to both. Sections I, II, and III are required for the airframe rating. Sections I, IV, and V are required for the powerplant rating. See chapter 6, section 2, paragraph 9 for information concerning previously passed section I. These test sections include:

• I—General. • II—Airframe Structures. • III—Airframe Systems and Components. • IV—Powerplant Theory and Maintenance. • V—Powerplant Systems and Components.

3. Parachute Rigger Tests. The test standards consist of knowledge/oral question elements and skill/practical project elements in each of the seven Areas of Operation. Each Area of Operation has from 5 to 14 Tasks. The Tasks are broken down by elements. All elements of a selected Task must be accomplished to successfully complete the Task. These Areas of Operation include:

• I—Certification. • II—Privileges, Limitations, and Operating Rules.

a. DME Designations. The DME can be issued the following designations: › (2) Powerplant (P).

• III—Packing Parachutes. • IV—Parachute Operation and Care. • V—Parachute Construction Details. • VI—Parachute Repair. • VII—Parachute Alteration.

4. FAA Certification Policy. TPEs must evaluate the oral and practical tests to determine if an applicant’s performance is acceptable or unacceptable. The primary discriminator in the airman certification process is the oral and practical test. Standard grading criteria and objective examination ensure a level of basic knowledge and skills in all subjects required for the rating sought.

5. Limitations. In addition to the general limitations in chapter 5, TPEs must not:

a. Conduct oral and practical tests at the base of operation that appears on the TPE’s certificate of authority (COA) letter unless it is adequately equipped with available equipment and material necessary for conducting the tests.

b. Conduct oral and practical tests for applicants that have been authorized to test on the applicable airman certificate and/or rating application by an inspector in a Flight Standards District Office (FSDO) or International Field Office (IFO) other than the TPE’s responsible FSDO or IFO, unless:

(1) The TPE reports the request for testing to the FSDO or IFO responsible for his or her designee authorization.

(2) The TPE receives written permission before conducting the test. The TPE may be issued continuing authorization to perform these tests. This authorization does not relieve the TPE from the notification requirements of chapter 6, section 2, paragraph 9 before performing the test. The continuing authorization should be listed on the COA, but may be amended or rescinded any time the TPE’s responsible FSDO or IFO finds necessary.

Note: This paragraph is intended as a limitation for the TPE. An applicant is not required to present his or her application to the local FSDO or IFO for reauthorization unless there is evidence that his or her original authorization is in question.

c. Conduct an oral or practical test in any language other than the English language.

6. Designations Issued.

a. DME Designations. The DME can be issued the following designations:

(1) Airframe (A). Conducts aviation mechanic airframe rating oral and practical tests and the general oral and practical test, when required.

(2) Powerplant (P). Conducts aviation mechanic powerplant rating oral and practical tests and the general oral and practical test, when required.

8. Security. › a. Materials. The TPE must ensure adequate security of:

(3) Airframe and Powerplant (A&P). Conducts aviation mechanic airframe and powerplant ratings, oral and practical tests, and the general oral and practical test, when required.

b. DPRE Designations. The DPRE will be issued one designation, Parachute Rigger Examiner. The DPRE conducts senior and master parachute rigger oral and practical tests for the parachute types for which the DPRE is rated.

7. Designee Materials. The managing FAA office should provide each designee with supplies appropriate to the designation. The following supplies are necessary for the performance of TPE duties. The managing FAA office may issue some or all of the designee materials at the time of selection. With the exception of the FAA Form 8060-4, the material can be found on the Internet, or through common sources such as the Government Printing Office (GPO).

a. FAA Order 8900.2. FAA Order 8900.2, General Aviation Airman Designee Handbook.

b. FAA Form 8610-2. FAA Form 8610-2, Airman Certificate and/or Rating Application (Stock No. 0052-00-026-8004).

c. FAA Form 8060-4. FAA Form 8060-4, Temporary Airman Certificate (Stock No. 0052-00-049-5001).

d. FAA Form 337. FAA Form 337, Major Repair and Alteration (Stock No. 0052-00-025-8000).

e. Title 14 CFR Part 65. Title 14 CFR Part 65, Certification: Airmen Other Than Flight Crewmembers.

f. Title 14 CFR Part 183. Title 14 CFR Part 183, Representatives of the Administrator.

g. FAA-S-8081-25. Parachute Rigger Practical Test Standards (PTS), FAA-S-8081-25.

h. FAA-S-8081-26. Aviation Mechanic General Practical Test Standards (PTS) FAA-S-8081-26.

i. FAA-8081-27. Aviation Mechanic Airframe Practical Test Standards (PTS) FAA-8081-27.

j. FAA-8081-28. Aviation Mechanic Powerplant Practical Test Standards (PTS) FAA-8081-28.

Note: Items listed in paragraphs 7d, h, i, and j, are not required for DPREs; the item listed in paragraph 7g is not required for DMEs.

8. Security. Each TPE is responsible for establishing and carrying out appropriate security procedures. The security of the controlled material is important to prevent compromise, and to ensure the applicants meet the aeronautical skill standards for aviation mechanic certificates and ratings.

a. Materials. The TPE must ensure adequate security of:

b. Knowledge and Skill Elements. Use the knowledge (oral) and skill… › (2) For the DPRE: Area of Operation.

(1) All knowledge element questions developed for the tests.

(2) All skill element projects developed for the tests.

b. Access. The TPE must secure the aforementioned material in a manner that will not allow unauthorized access (e.g., a locked drawer, cabinet, or closet). Only authorized representatives of the FAA Administrator will receive access to secured material. The TPE should refer any public request for the secured material to the managing FAA office.

Section 2. Conducting and Grading Tests

9. Preparation. TPEs must notify the managing FAA office before conducting all oral and practical tests. The managing FAA office may establish specific procedures for this notification. Because applicants may have widely differing backgrounds, it will be necessary to review the applicant’s experience in order to select appropriate oral questions and practical projects. The TPE must ask questions and assigns projects that will be fair, and yet cover all subject areas/Areas of Operation necessary for certification.

a. Charge a Reasonable Fee. The TPE may charge a reasonable fee to each applicant for handling the forms and reports incident to the issuance of an aviation mechanic certificate, and for the use of the TPE’s facilities, equipment, and materials, service in administering the oral and practical tests. The TPE and the applicant should reach a mutual understanding and agreement of the total fee for the TPE’s services before beginning the tests. An agreement in writing may be to the advantage of both the TPE and the applicant.

b. Knowledge and Skill Elements. Use the knowledge (oral) and skill (practical) elements listed in the PTS to administer the oral and practical tests. It is essential to forward a copy of all knowledge element questions and skill element test projects developed by the TPE to the managing FAA office. Unless otherwise authorized by the managing FAA office, the TPE must forward the questions and/or projects to the FAA at least 30 calendar-days before their use in an oral and practical test.

Note: This does not include questions downloaded from the Internet-based Oral Question Generator.

(1) For the DME: Subject Area. Test in each Subject Area of each section required for the rating sought; one-third of the section must be Level 1 or higher, one-third must be Level 2 or higher, and one-third must be Level 3, even though the applicant may not have used some of the skills in past or present jobs. The DME is not required to test every element in each Subject Area. An applicant must be able to demonstrate satisfactory knowledge and skill in the assigned elements in each Subject Area to the required standard.

(2) For the DPRE: Area of Operation. Test in each Area of Operation required for certificate/rating sought. An applicant must perform satisfactorily in each selected Task in each required Area of Operation.

(2) The TPE should use the following basic guidelines to assist in… › (c) Knowledge questions should be limited only to who, what, when,…

c. Developing Knowledge (Oral) Element Tests. This type of questioning intends to measure an applicant’s basic knowledge of a Subject Area/Area of Operation. The design of the knowledge question is directly relational to the accuracy of this measurement.

(1) For the DME: The DME may continue to develop and use knowledge element questions. Use the guidelines from subparagraph (2) below, to assist in the development of questions. The DME may also use questions obtained from the Internet-based Oral Question Generator at: https://av-info.faa.gov/DsgReg/Login.aspx. Select developed and/or downloaded questions applicable to the type of test to be administered. Do not select more than 10 questions for each Subject Area to be tested. Do not use the same questions for three consecutive tests. Do not allow an applicant to select questions.

(2) The TPE should use the following basic guidelines to assist in developing knowledge questions.

(a) The knowledge questions should be:

1. Clear. Content should establish the conditions or significant circumstances so the examiner and the applicant will have the same mental picture.

2. Grammatically correct.

3. Concise. Long questions can be complex and ambiguous.

4. Pertinent to the skill element when combining knowledge (oral) and skill elements.

5. Have only one correct answer.

(b) The questions should not:

1. Be open-ended or multiple-choice questions.

2. Require any further information or clarification.

3. Be manufacturer specific.

4. Contain double negatives.

5. Have two parts.

6. Contain clues to the answer.

(c) Knowledge questions should be limited only to who, what, when, where, how, or why, not a combination. The questions should challenge the applicant enough so the examiner can properly evaluate the applicant’s basic knowledge. Answers to the knowledge questions must be found within FAA-approved or accepted information sources (e.g., 14 CFR parts, FAA orders, or advisory circulars (AC)).

h. Conduct a Pretest Interview. The TPE should accomplish the pretest… › (2) Advise the applicant when the day’s activities terminate, and when…

d. Develop Skill (Practical) Element Projects. The objective of this type of test is to measure an applicant’s basic skills in a Subject Area/Area of Operation. The design of the skill element is directly relational to its assigned level and to the accuracy of this measurement. Use the following basic guidelines to assist in the development of skill projects.

(1) Include any givens (e.g., specific tools, equipment, mock ups, technical data) that will be required for the project.

(2) Be clear and concise with the level, if applicable, clearly identified.

(3) Refer to the standard(s) by which the project will be graded. The examiner must develop a performance standard for each project and include:

(a) What the applicant must do. As an example: (for mechanic applicants) install an assigned control surface; (for parachute rigger applicants) inspect a pilot chute.

(b) How it must be done. As an example: use of proper information (e.g., manufacturer’s data, Type Certificate Data Sheet (TCDS)) proper tooling, and observance of all applicable safety precautions.

e. Assign Unique Identifier. The examiner must assign a unique identifier to each knowledge element question and skill element project developed.

f. Prescribed Length of Time. There is no standard length of time prescribed for oral and practical tests. The testing period must, however, be long enough to make a valid determination in each Subject Area or Area of Operation for the rating sought. Take appropriate time to ensure that all required knowledge element questions and skill element practical projects have been completed for the rating sought.

g. Two Originals. The applicant submits two originals of FAA Form 8610-2 before testing begins. The applicant must complete FAA Form 8610-2 in accordance with Figure 6-1, which includes the instructions for completing FAA Form 8610-2. The TPE or inspector should provide FAA Form 8610-2 and give detailed instructions for completing it correctly. (The inspector or TPE must copy Figure 6-1 and provide it to the applicant until FAA Form 8610-2 is revised with written instructions attached.) Advise the applicant to read the supplemental information attached to FAA Form 8610-2. (See Figure 6-1.)

Note: All signatures must be original, in dark ink, with the name printed or typed below or next to the signature.

h. Conduct a Pretest Interview. The TPE should accomplish the pretest interview face to face, by telephone/fax, through e-mail, or other methods that will allow the TPE to:

(1) Discuss fees, testing procedures, projects, and type of equipment to be used and what the applicant should expect if they pass, fail, or do not complete the test.

(2) Advise the applicant when the day’s activities terminate, and when testing resumes if more than 1 day is needed.

(3) Ensure the applicant’s eligibility. (See paragraph 10).

(a) Review the applicant’s FAA Form 8610-2 for completeness and correctness. The TPE must have the applicant correct any errors. This may require the applicant to return to the FSDO or IFO where authorization was obtained.

k. For the DME: The General Section of the Tests. The DME should not… › (1) An applicant is not required to take section I, General, of a…

(b) Review the applicant’s current written test results that are applicable to the rating(s) sought.

(c) Have the applicant indicate, in the event that he or she passes all of the required tests, how he or she will respond to the two questions listed in block IV, “APPLICANT’S CERTIFICATION”, located on the reverse side of FAA Form 8610-2. There may be a need to have managing FAA field office involvement if the applicant would be required to answer “YES” to either of the questions.

(4) Advise applicant of part 65, § 65.19 retesting after failure provisions and restrictions.

i. Progressive Tests Must Not Be Given. Although it may be necessary to continue a test for more than 1 day, tests must not be allowed to continue for long periods. Progressive testing is defined as testing which continues for more than four sessions in a 4-day period. Suspending the test to allow the applicant further study is not allowed. Both the applicant and the examiner should plan the testing times so the applicant completes most of the test once it commences.

j. Incomplete Test. Should the test not be completed in the allotted timeframe, the examiner will correctly mark both FAA Forms 8610-2 (two originals) on the reverse side. Forward this incomplete test file to the managing FAA office within 7 calendar-days. When practical, schedule a retest for the areas not completed at the time the test is discontinued. Treat this retest as if the applicant had failed those portions not tested. (See paragraphs 10d and 10e.)

(1) For the DME: Correctly mark for the subject areas completed. Incomplete subject areas will not be marked as a failure on the FAA Form 8610-2 (two originals). In addition, place a statement in the “REMARKS” area indicating why the test was not completed. Some examples are located in the figures at the end of this chapter.

(2) For the DPRE: Do not mark as a failure. Place a statement in the “REMARKS” area indicating why the test was not completed on both FAA Form 8610-2. Some examples are located in the figures at the end of this chapter.

Note: Do not start any test without the intent to complete the testing for the issuance of a certificate and at least one rating or an added rating.

k. For the DME: The General Section of the Tests. The DME should not begin a test with the intent of testing the General section only. Applicants for an airframe rating must take sections I, II, and III. Applicants for a powerplant rating must take sections I, IV, and V.

(1) An applicant is not required to take section I, General, of a knowledge or skill test for a mechanic rating if it was previously passed. Proof of passing may be in the following forms:

(1) All applicants claiming civilian and/or military experience as a… › (c) Review FAA Form 8610-2 for completeness, sign and complete block V…

(2) A mechanic certificate with the alternate rating; or

(3) FAA Form 8610-2 that shows section I, General, has been passed within the preceding 24 calendar-months (although other sections may not have been passed).

10. Applicant Eligibility.

a. Furnish Current, Government-Issued Identification. Applicants must furnish current, valid, government-issued identification with a photograph and signature. If FAA Form 8610-2 is completed at a FSDO or IFO, the approving inspector will record the method of identification (e.g., passport, U.S. military identification, U.S. driver’s license), number, and expiration date in the “REMARKS” area of FAA Form 8610-2. The TPE will verify the applicant’s identification before testing. If the means of identification was provided in the “REMARKS” area, the TPE will verify the identification and initial the inspector’s entry. (Sample entry: Oklahoma Driver’s License #123456789 exp. 01/31/2010.) If the means of identification was not previously entered in the “REMARKS” area or the means of identification provided by the applicant is different from the one listed in the “REMARKS” area, the TPE will make the entry in the “REMARKS” area and initial the entry. (See Figures 6-2F to 6-2K (mechanic applicants) and Figures 6-3C to 6-3E (parachute rigger applicants).)

b. Meet English Language Requirements. The designated examiners and aviation safety inspectors (ASI) share the responsibility for ensuring applicants meet the English language requirements. (Before accepting the application and beginning the practical test for certificate or rating, the TPE/ASI must evaluate the applicant’s English fluency using the appropriate guidance.) The current edition of AC 60-28, English Language Skill Standards Required by 14 CFR Parts 61, 63, and 65, provides guidance for airman applicants, TPEs, and ASIs in determining English language skills required for airman certification.

c. Original FAA Form 8610-2.

(1) All applicants claiming civilian and/or military experience as a basis for qualification must have the experience evaluated and verified by an inspector before taking the required test. The inspector may, as a matter of office procedures, reproduce and retain copies of FAA Form 8610-2 and documented evidence presented by the applicant. The inspector will:

(a) Evaluate the experience documents and verify them, if necessary.

(b) Have the applicant complete FAA Form 8610-2 (two originals). (See Figures 6-2A, 6-2B, 6-2D, 6-2E, 6-3A, and 6-3B.) Provide a copy of Figure 6-1 to the applicant. Instruct the applicant to detach, if necessary, and read the “Privacy Act” area of FAA Form 8610-2.

(c) Review FAA Form 8610-2 for completeness, sign and complete block V of FAA Form 8610-2 (both originals), and return them if the applicant meets the experience requirements. Return all experience documents to the applicant. Both original FAA Form 8610-2 applications must be retained by the applicant to present to a TPE or inspector for the oral and practical tests.

(a) Graduates from AMTSs Having Affiliated DMEs. › 6. Affiliated DMEs are required to review FAA Form 8610-2 to determine…

Note: The block V endorsement must not be restricted to a specific field office or region.

(d) Only Maintenance or Avionics inspectors who hold the mechanic certificate with airframe and/or powerplant ratings are authorized to review and endorse block V of FAA Form 8610-2.

(2) For the DME: Applicants attending or graduating from an approved Aviation Maintenance Technician School (AMTS).

(a) Graduates from AMTSs Having Affiliated DMEs. These individuals need not present the graduation certificate or certificate of completion appropriate to rating sought to the local inspector before taking the computer knowledge test and oral and practical tests provided:

1. The AMTS has an affiliated computerized testing center and an affiliated DME, and the affiliated examiners give the tests.

2. The AMTS has established a procedure acceptable to the managing FSDO having jurisdiction over the AMTS. This procedure will require the AMTS to provide a certified list of graduates to the FSDO and to each of the AMTS’s affiliated computerized testing centers, and DMEs. The list must be available before the computerized testing center or DMEs administering the appropriate test(s). The AMTS will maintain and provide a current list of affiliated computerized testing centers and DMEs to the FSDO.

3. The AMTS’s certified list must contain the names and addresses of graduates, graduation dates, and the curriculum from which the applicant graduated (e.g., airframe, powerplant, or airframe and powerplant combined). The list will reflect a statement certifying these graduates and will be signed and dated by an authorized AMTS official.

Note: Graduates taking the written or oral and practical tests from examiners, other than those affiliated with the AMTS, must present a graduation certificate or certificate of completion to the managing FAA office. This also applies to nonaffiliated computerized testing centers. (The inspector must review the documents, complete block V and sign it. This authorizes the AMTS graduate to be tested by an examiner other than an AMTS affiliated examiner.)

4. Affiliated AMTS DMEs may administer oral and practical tests to graduates/applicants, without an FAA signature in block V of FAA Form 8610-2 only when a graduation certificate or certificate of completion is presented and the AMTS provides the DME with the certified list of graduates.

5. Applicants must complete FAA Form 8610-2 (both originals).

6. Affiliated DMEs are required to review FAA Form 8610-2 to determine and assure that it is complete and correct, and should verify the applicant meets the requirements of part 65, §§ 65.11, 65.12, and 65.71, before issuing FAA Form 8060-4. The applicant will present appropriate computerized test report(s). All sections of the computer knowledge test must have been passed within the previous 24 calendar-months.

(3) For the DPRE: Senior, Master, Added ratings and Military. › (d) Military Parachute Riggers.

(b) Taking Oral and Practical Tests Before Computer Knowledge Tests. AMTS students may be authorized by the managing FSDO to take the oral and practical tests before the computer knowledge test in accordance with § 65.80.

1. Each student must complete the front of FAA Form 8610-2 (both originals). FAA Form 8610-2 must show the AMTS’s name and location (block II, item D1), AMTS’s certificate number (block II, item D2), curriculum in which student is enrolled (block II, item D3), and graduation date (block II, item D4). Applicants should not check block II, item D, “GRADUATE OF APPROVED COURSE.”

2. AMTSs must show that each student is in the final phase of training and has maintained satisfactory progress at the school.

Note: The student must be within 45 calendar-days of completing that phase of the curriculum. If enrolled in the Airframe only or Powerplant only, must have completed the General and be within 45 calendar-days of completion for the Airframe or Powerplant. If the applicant is enrolled in the Powerplant, and has completed the General and Airframe, he or she must be within 45 calendar-days of completion of the Powerplant curriculum. If the student is enrolled in the combined Airframe and Powerplant, he or she must be within 45 calendar-days of completion of the complete curriculum for the combined Airframe and Powerplant, has made satisfactory progress, and is prepared for the test. The proper AMTS official must complete block II, item E, (1) and (2).

3. Inspectors must complete block II, item F, (1), (2), (3), and (4). The FAA authorization expiration date must not be later than the anticipated graduation date. Process the completed file through the managing FSDO. (The managing FSDO has authorized testing of any student by a nonaffiliated DME by completing block II, item F, (1), (2), (3), and (4).)

(3) For the DPRE: Senior, Master, Added ratings and Military.

(a) Senior parachute rigger applicants for an original certificate must show proof to an inspector or a DPRE of having passed the parachute rigger computer knowledge test (RIG) by presenting a computerized test report. (See Figure 6-3G.)

(b) Master parachute rigger applicants for an original certificate:

1. An applicant who does not hold a senior certificate must show proof to an inspector or a DPRE of having passed the RIG by presenting a computerized test report.

2. An applicant who holds a senior certificate must present the airman certificate to the examiner. No knowledge test is required.

(c) Adding a Rating. An applicant must present his or her senior or master certificate to the examiner. No knowledge test is required.

(d) Military Parachute Riggers. Current and former military parachute riggers may be tested in accordance with § 65.117 at a computer testing center.

Section 2. Conducting and Grading Tests › 11. Evaluating Applicant Performance.

d. Retests. When application is made for a retest after failure of a previous test or incomplete test, the applicant must:

(1) Complete FAA Form 8610-2 (both originals) in accordance with the instructions furnished by the TPE or inspector.

Note: FAA Form 8610-2, block V does not need to be signed by an inspector if a copy of the original FAA Form 8610-2 (with authorizing signature) is attached to the file.

(2) Present an appropriate computerized test report. All sections of the computer knowledge tests must have been passed within the previous 24 calendar-months.

(3) Present his or her original of FAA Form 8610-2 from the previous oral and practical tests showing the sections or Areas of Operation failed, not completed, or for which passing credit has expired (mechanic applicants only).

(4) If the retest is within 30 calendar-days of the previous test, present a statement by a person authorized in § 65.19 that the applicant received additional instruction for each subject failed and the applicant is ready for retesting. This statement of training is required only when the applicant failed portions of the test. This statement of training is not required for Subject Areas not completed on the previous test. (See Figures 6-2N and 6-3G.)

e. Test in All Required Areas. Test applicants for retest in all areas of the oral and/or practical tests in the section(s) or Area(s) of Operation listed as failed, that was/were not taken, or that has/have expired.

(1) For the DME: Applicants who apply for retesting within 60 calendar-days to the same DME who gave the failed test may, at the option of the DME, be tested in only the Subject Areas failed on the previous test provided applicant has successfully passed all other Subject Areas within that section. (New questions and practical projects may be included in the retest.) Retest practical projects must be at the same level as failed.

(2) For the DPRE: Applicants who apply for retesting within 60 calendar-days to the same DPRE who administered the failed test may, at the option of the DPRE, be tested in only the Task(s) failed or that were not taken on the previous test, provided the applicant has successfully passed all other tasks.

Note: During a retest and at the discretion of the DPRE, any Task may be re-evaluated, including those previously passed.

11. Evaluating Applicant Performance. Do not expect an applicant to be competent in all phases of overhaul, maintenance, alteration, and repair, or be highly skillful in performing complex manipulative operations. However, expect the applicant to have developed basic skills and be able to demonstrate them during the practical test. Inform the applicant of the level of performance expected before beginning each project. DMEs can find the required performance levels in the PTS. DPREs should inform their applicants that they must demonstrate an approval for return to service proficiency on the assigned tasks.

11. Evaluating Applicant Performance. › c. Standards. Include the following standards in TPE observations for…

a. For the DME. When it becomes obvious during the test that an applicant cannot perform at an acceptable level and has already failed:

(1) Section. When it becomes obvious during the test that an applicant cannot perform at an acceptable level and has already failed several Subject Areas in a section, the DME may discontinue testing in that section and go on to the next section. In some cases, however, it may be advantageous to continue to the end of the section so the applicant will know his/her strengths and weaknesses when preparing for retest. After terminating testing in a section, the DME will make an appropriate note in the “REMARKS” area on the reverse side of FAA Form 8610-2.

(2) Subject Area. When it becomes obvious during the test that an applicant cannot perform at an acceptable level and has failed a Subject Area, the DME may discontinue testing in that Subject Area and go on to the next Subject Area. The DME or the applicant may discontinue the testing any time after the failure of a Subject Area. Several Subject Areas may be evaluated during an assigned practical project. In any case, the applicant is entitled to credit for only those Subject Areas satisfactorily completed.

Note: After terminating testing in a Subject Area, the DME will correctly score the Subject Area and make an appropriate note in the “REMARKS” area on the reverse side of FAA Form 8610-2. Some examples are located in the figures at the end of this chapter.

b. For the DPRE. When it becomes obvious during the test that an applicant cannot perform at an acceptable level and has already failed:

(1) Area of Operation. When it is obvious during the test that an applicant cannot perform acceptably and has already failed an Area of Operation, the DPRE may discontinue testing in that Area of Operation and go to the next. There is no maximum number of projects the DPRE may evaluate in an Area of Operation. In some cases it may be advantageous to complete an already failed test so the applicant will know his or her strengths and weaknesses when preparing for a retest.

(2) Tasks. When evaluating an Area of Operation with more than one Task assigned and it becomes obvious during the test that an applicant cannot perform at an acceptable level and has already failed one of the assigned Tasks, the DPRE may discontinue testing in that Area of Operation or go on with the next Task. The DPRE or the applicant may discontinue the testing any time after the failure of a Task. In any case, the applicant is entitled to credit for only those Tasks satisfactorily completed.

Note: If testing for a certificate/rating was terminated, the DPRE will make an appropriate note listing the Area(s) of Operation and associated Task(s) failed, or not completed, in the “REMARKS” area on the reverse side of the Form 8610-2. Some examples are located in the figures at the end of this chapter.

c. Standards. Include the following standards in TPE observations for evaluating applicant performance:

a. Conducting the Oral Test. › (4) Although the answers to the oral questions should be available in…

(1) Approach to the project; proper information and tools; preparation of the equipment; and observation of safety precautions;

(2) Cleaning, preparing, and protecting parts; skill in handling tools; thoroughness and cleanliness;

(3) The functions of the units or systems of the assigned project; use of current maintenance and/or overhaul procedures;

(4) Final inspection for safety and operation;

(5) Completion of required forms and records;

(6) Application of appropriate rules; and

(7) Attitude toward safety, manufacturer’s recommendations, and acceptable industry practices.

12. Conducting the Tests.

a. Conducting the Oral Test.

(1) Oral questioning may be used at any time during the practical test.

(a) For the DME: Ask at least four questions in each Subject Area. These questions should be from more than one element listed under Objective 1 in the PTS for that Subject Area. The applicant must be able to answer successfully 70 percent of the oral questions asked in each Subject Area. Each Subject Area must be passed in order to pass a section.

Note: Use no more than 10 questions to evaluate a Subject Area.

(b) For the DPRE: At minimum, quiz the applicant on each knowledge element for each objective in a selected Task. The minimum passing grade is 70 percent of the number of knowledge questions asked in each selected Task. Applicants must pass each Task to pass the Area of Operation. The DPRE is not required to use oral questions for skill-only tasks.

(2) An applicant’s answers to oral questions must show an understanding of the subject and ability to apply knowledge. Do not allow an applicant’s skill of oral expression or ability to memorize details affect oral test evaluation. If necessary, additional exploratory questions may be used to verify the applicant’s understanding of the subject area, but will not be considered as part of the test.

(3) To determine if the oral questions are answered correctly, the TPE must be able to reference information (e.g., manufacturer’s data, ACs, CFR). The TPE must be objective in making the determination.

(4) Although the answers to the oral questions should be available in the CFRs, manufacturer’s maintenance data, or other aviation related data, the applicant must be able to answer successfully all oral questions without the use of any reference materials.

b. Conducting the Practical Test.

Continue reading ↓ 120 of 774 passages shown