Order 8610.12 Technical Personnel Examiner Handbook
This document is cancelled. It may have been replaced. Check the official source before relying on it.
U.S. DEPARTMENT OF TRANSPORTATION
U.S. DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION
National Policy
ORDER 8610.12
Effective Date:
7/14/08
SUBJ: Technical Personnel Examiner Handbook
FOREWORD
1. This order combines the information previously contained in Order 8610.4, Aviation Mechanic Examiner Handbook, and Order 8610.5, Parachute Rigger Examiner Handbook, and replaces those orders.
FEDERAL AVIATION ADMINISTRATION
2. This order stresses Federal Aviation Administration (FAA) policy of emphasizing the Technical Personnel Examiner’s (TPE) knowledge of oral and practical tests; it also concerns the administration of such tests. For the purposes of this order, TPE will refer only to Designated Mechanic Examiners and Designated Parachute Rigger Examiners. This order applies to all Airworthiness inspectors (hereafter referred to as inspectors) who review and approve/disapprove TPE applications and testing files. This order does not relieve inspectors from the responsibility of instructing and guiding TPEs.
3. When differences in guidance appear between this order and FAA Order 8900.1, Volume 5, Chapter 5, Section 2, Certificate Airframe and/or Powerplant Mechanic/Added Rating; Volume 5, Chapter 5, Section 3, Certificate Foreign Applicants Located Outside the United States for Title 14 CFR Part 65 Mechanic Certificate/Ratings; Volume 5, Chapter 5, Section 9, Certificate 14 CFR Part 65 Mechanic Certificate/Ratings; and Volume 13, Chapter 9, Certificate/Renew Designated Airworthiness Representative, use the document with the most current revision date.
ORIGINAL SIGNED by
James J. Ballough Director, Flight Standards Service
Distribution: Electronic Only Initiated By: AFS-640
Table of Contents
Paragraph Page
Chapter 1. General Information
Chapter 1. General Information
Section 1. Introduction
1. Purpose of This Order … 1-1 2. Audience … 1-1 3. Where You Can Find This Order … 1-1 4. What This Order Cancels … 1-1 5. Explanation of Policy Changes … 1-1 Section 2. TPE Program
6. General … 1-1 7. FAA Certification Policy … 1-2 8. Designations Issued … 1-2 9. Designee Materials … 1-2 10. Security … 1-3
Chapter 2. Selection and Appointment of a TPE
Chapter 2. Selection and Appointment of a TPE
1. Selection … 2-1 2. General Requirements for Appointment … 2-2 3. Delegation/Recision of a TPE Authorization … 2-4
Chapter 3. Training, Supervision, and Renewal
1. Training … 3-1 2. Recurrent Training … 3-1 3. Supervision … 3-2 4. Expiration … 3-2 5. Renewal … 3-2 6. Knowledge and Skill … 3-4
Chapter 4. Privileges and Limitations
Chapter 4. Privileges and Limitations
1. Privileges … 4-1 2. Limitations … 4-1 3. Geographical Area … 4-2
Chapter 5. Conducting and Grading Tests
1. Preparation … 5-1 2. Applicant Eligibility … 5-4 3. Evaluating Applicant Performance … 5-8 4. Conducting the Tests … 5-10 5. Test Planning Sheets Are Required for Each Oral and Practical Test Given … 5-13 6. Recording the Results of a Test … 5-13 7. When the Applicant Passes … 5-13 8. Applicants Under 18 Years of Age … 5-15 9. When the Applicant Fails … 5-16 10. Disposition of Files … 5-16
Chapter 5. Conducting and Grading Tests
ii
Table of Contents (Continued)
Paragraph Page
11. Issuance of FAA Form 8060-4 by a TPE When Oral and Practical Tests are Not Administered … 5-18 12. Reconstruction of a Lost Certification File … 5-19
Chapter 6 Termination
1. Termination … 6-1 2. Reasons for Termination … 6-1 3. Examples of Deficiencies … 6-1 4. Documentation … 6-1 5. Proposed Termination … 6-2 6. Notification … 6-2 7. Option to Respond … 6-2 8. FSDO or IFO Manager’s Decision … 6-2 9. Appeal … 6-2 10. Voluntary Surrender … 6-2
Chapter 7 Administrative Information
Chapter 7 Administrative Information
1. Distribution … 7-1 2. Deviations … 7-1 3. Suggestions or Comments … 7-1
Appendix A. Instructions for Completing FAA Form 8610-2, Airman Certificate and or Rating Application
1. Procedures for Completing FAA Form 8610-2 … A-1 2. Privacy Act … A-2 3. Complete the Top Section … A-2 4. Block I—Applicant Information … A-2 5. Block II—Certificate or Rating Applied for on Basis of— … A-6 6. Block III—Record of Experience … A-9 7. Block IV—Applicant’s Certification … A-11 8. Block V—I Find This Applicant Meets the Experience Requirements of FAR 65 and is Eligible to Take the Required Tests … A-12 9. For FAA Use Only … A-12 10. Results of Oral and Practical Tests … A-13 11. Designated Examiner’s Report … A-14 12. Applicant’s Certification … A-14 13. FAA Inspector’s Report … A-15
Appendix B. Nationality (Citizenship) to be Used to Complete Block I of FAA Form 8610-2, Airman Certificate and/or Rating Application … B-1
Appendix C. Information About the Initial TPE Standardization Seminars … C-1
Appendix C. Information About the Initial TPE Standardization Seminars … C-1
iii
Table of Contents (Continued)
Paragraph Page
Appendix D. Example Forms for Designated Mechanic Examiner Applicants … D-1
Appendix E. Example Forms for Designated Parachute Rigger Examiner Applicants … E-1
Appendix E. Example Forms for Designated Parachute Rigger Examiner Applicants … E-1
Appendix F. Airframe and Powerplant Mechanic and Parachute Rigger Oral and Practical Test Planning Sheets … F-1
List of Figures
Figure Page
A-1. Privacy Act … A-1 A-2. Top Section … A-2 A-3. Block I—Applicant Information … A-2 A-4. Block II—Certificate or Rating Applied For On Basis of— … A-6 A-5. Block III—Record of Experience … A-8 A-6. Block IV—Applicant’s Certification … A-11 A-7. Block V—I Find This Applicant Meets The Experience Requirements Of 14 CFR 65
And Is Eligible To Take The Required Tests … A-12 A-8. For FAA Use Only … A-12 A-9. Results of Oral and Practical Tests … A-13 A-10. Designated Examiner’s Report … A-14 A-11. Applicant’s Certification … A-14 A-12. FAA Inspector’s Report … A-15 B-1. Alphabetical Listing of Countries for Form 8610-2 … B-1 D-1. FAA Form 8610-2, Airman Certificate and/or Rating Application … D-1 D-2. FAA Form 8610-2, Airman Certificate and/or Rating Application(Applicant cannot list
all experience required in block III) … D-2 D-3. Attachment for FAA Form 8610-2, Airman Certificate and/or Rating Application
(Applicant cannot list all experience required in block III) … D-3 D-4. FAA Form 8610-2, Airman Certificate and/or Rating Application (Applicant is a
graduate of an AMTS with affiliated computer test center and DMEs) … D-4 D-5. FAA Form 8610-2, Airman Certificate and/or Rating Application (Applicant is
authorized to take the oral and practical tests before the computer knowledge test.) . D-5 D-6. Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) (Typical
entries for oral and practical tests administered by a DME. All Sections passed. Application approved) … D-6 D-7. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side)
(Typical entries for oral and practical tests administered by a DME. Applicant failed Section IV. Application disapproved.) … D-7 D-8. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side)
(Typical entries for oral and practical tests administered by a DME using PTS) … D-8
iv
v
List of Figures (Continued)
Figure Page
D-9. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side)
(Typical entries for oral and practical tests administered by a DME … D-9 D-10. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side)
(Typical entries when applicant is under 18 years of age.) … D-10 D-11. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side)
(Typical entries when applicant is testing under 14 CFR part 65, § 65.80.) … D-11 D-12. FAA Form 8060-4, Temporary Airman Certificate (Original Issuance.) … D-12 D-13. FAA Form 8060-4, Temporary Airman Certificate (Reissuance retaining original
certificate number.) … D-13 D-14. Example Statement of Additional Instructions … D-14 D-15. Airman Computer Test Report for AMA … D-15 E-1. FAA Form 8610-2, Airman Certificate and/or Rating Application (Typical Entries for
Senior Parachute Rigger) … E-1 E-2. FAA Form 8610-2, Airman Certificate and/or Rating Application(Typical Entries for
Master Parachute Rigger) … E-2 E-3. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse) (Typical
Entries for Senior/Master Parachute Rigger) … E-3 E-4. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse) (Typical
Entries for Senior/Master Parachute Rigger When Test is Failed) … E-4 E-5. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse) (Typical
Entries When Applicant is Under 18 Years of Age) … E-5 E-6. Example Statement of Additional Instruction … E-6 E-7. Airman Computer Test for RIG … E-7 E-8. FAA Form 8060-4, Temporary Airman Certificate … E-8 E-9. FAA Form 8060-4, Temporary Airman Certificate (Original Issuance With Superseded
Airman Certificate Block Filled In) … E-9 E-10. FAA Form 8060-4, Temporary Airman Certificate (Reissuance Retaining Original
Certificate Number) … E-10 F-1. Airframe and Powerplant Mechanic Oral and Practical Planning Sheet (Front Side)..F-1 F-2. Airframe and Powerplant Mechanic Oral and Practical Planning Sheet (Back Side)..F-2 F-3. Parachute Rigger Oral/Practical Test Planning Sheet … F-3
Chapter 1. General Information
Chapter 1. General Information
Section 1. Introduction
1. Purpose of This Order. This order provides policy and mandatory, standardized procedures for people who administer all aviation mechanic or parachute rigger oral and practical tests. Compliance with these standardized procedures ensures that applicants meet a satisfactory level of competence and workmanship required for certification. This order does not relieve inspectors from instructing and guiding the following Technical Personnel Examiners (TPE): Designated Mechanic Examiners (DME) and Designated Parachute Rigger Examiners (DPRE).
Section 1. Introduction
2. Audience. The primary audience is inspectors and TPEs responsible for administering oral and practical tests.
3. Where You Can Find This Order. Inspectors can access this order through the Flight Standards Information Management System (FSIMS) at http://fsims.avs.faa.gov. Operators may find this information at: http://fsims.faa.gov.
4. What This Order Cancels. This order cancels FAA Order 8610.4K, Aviation Mechanic Examiner Handbook, and FAA Order 8610.5K, Parachute Rigger Examiner Handbook, both dated April 21, 2006.
5. Explanation of Policy Changes. This revision incorporates updated information, procedural and policy changes, and new guidance.
Section 2. TPE Program
Section 2. TPE Program
6. General. The procedures this order contains apply to inspectors and TPEs authorized to conduct aviation mechanic or parachute rigger oral and practical tests. TPEs will conduct tests in accordance with the Practical Test Standards (PTS) as applicable.
a. Aviation Mechanic Tests. The tests, in three separate booklets, consist of knowledge (oral question) elements and skill (practical project) elements in each of the five Sections. Each Section has from 3 to 12 Subject Areas. Section I, General, is required for either the airframe or powerplant rating and applies to both. Sections I, II, and III are required for the airframe rating. Sections I, IV, and V are required for the powerplant rating. See chapter 5, paragraph 1k(1) for information concerning previously passed Section I. The Sections are listed below:
• I—General.
• II—Airframe Structures.
• III—Airframe Systems and Components.
• IV—Powerplant Theory and Maintenance.
• V—Powerplant Systems and Components.
b. Parachute Rigger Tests. The tests consist of knowledge/oral question elements and skill/practical project elements in each of the seven Areas of Operation. Each Area of Operation has from 5 to 14 Tasks. The Tasks are broken down by elements. All elements of a selected Task must be accomplished to successfully complete the Task. The Areas are listed below:
• I—Certification.
• II—Privileges, Limitations, and Operating Rules.
• III—Packing Parachutes.
• IV—Parachute Operation and Care.
• V—Parachute Construction Details.
• VI—Parachute Repair.
• VII—Parachute Alteration.
7. FAA Certification Policy. TPEs must emphasize the oral and practical tests to determine if an applicant’s performance is acceptable or unacceptable. The primary discriminator in the airman certification process is the oral and practical test. A standard grading criterion and objective examination ensure a level of basic knowledge and skills in all subjects required for the rating sought.
8. Designations Issued.
a. The DME can be issued the following designations:
(1) Airframe (A). Conducts aviation mechanic airframe rating oral and practical tests and the general oral and practical test, when required.
(2) Powerplant (P). Conducts aviation mechanic powerplant rating oral and practical tests and the general oral and practical test, when required.
(3) Airframe and Powerplant (A&P). Conducts aviation mechanic airframe and powerplant ratings, oral and practical tests, and the general oral and practical test, when required.
b. The DPRE will be issued one designation, Parachute Rigger Examiner. The DPRE conducts senior and master parachute rigger oral and practical tests for the parachute types for which the DPRE is rated.
9. Designee Materials. The supervising Flight Standards District Office (FSDO) or International Field Office (IFO) should provide each designee with supplies appropriate to the designation. The following supplies are necessary to performance TPE duties. The supervising FSDO or IFO may issue some or all of the designee materials at the time of selection. With the exception of the FAA Form 8060-4, Temporary Airman Certificate, the material can be found on the Internet, or through common sources such as the Government Printing Office (GPO).
a. Order 8610.12, Technical Personnel Examiner Handbook.
b. FAA Form 8610-2, Airman Certificate and/or Rating Application, (Stock No. 0052-00-026-8004).
c. FAA Form 8060-4, Temporary Airman Certificate (Stock No. 0052-00-049-5001).
d. FAA Form 337, Major Repair and Alteration (Stock No. 0052-00-025-8000).
e. Title 14 of the Code of Federal Regulations (14 CFR) part 65, Certification: Airmen Other Than Flight Crewmembers.
f. Title 14 CFR part 183, Representatives of the Administrator.
g. Aviation Mechanic General Practical Test Standards (PTS) FAA-S-8081-26.
h. Aviation Mechanic Airframe PTS FAA-8081-27.
i. Aviation Mechanic Powerplant PTS FAA-8081-28.
j. Parachute Rigger PTS FAA-S-8081-25.
Note: Items d, g, h, and i, are not required for DPREs; item j is not required for DMEs.
10. Security. Each TPE is responsible for establishing and carrying out appropriate security procedures. The security of the controlled material is important to prevent compromise, and to ensure the applicants meet the aeronautical skill standards for aviation mechanic certificates and ratings.
a. The TPE must ensure adequate security of:
(1) All knowledge element questions for the tests.
Note: For DMEs this includes questions developed by the DME and questions downloaded or printed from the Internet-based knowledge question data bank. Refer to chapter 5, paragraph 5-1c for additional information on the question data bank.
(2) All skill element projects developed for the tests.
b. The TPE must secure the aforementioned material in a manner that will not allow unauthorized access (e.g., a locked drawer, cabinet, or closet). Only authorized representatives of the FAA Administrator will receive access to secured material. The TPE should refer any public request for the secured material to the supervising FSDO or IFO.
Chapter 2. Selection and Appointment of a TPE
Chapter 2. Selection and Appointment of a TPE
1. Selection.
a. Application. The supervising FSDO or IFO selects applicants for a TPE appointment. When selecting approved candidates, the FSDO or IFO considers the recommendations from knowledgeable members of the aviation community. The National Examiner Board (NEB) receives applications and will review designee applicants for general qualifications.
(1) All TPE applicants must complete the FAA Form 8110-28, Application and Statement of Qualification (DME/DPRE/DAR-T/ODAR-T). Address the application package to:
FAA National Examiner Board Attn: Designee Quality Assurance Branch, AFS-650
P.O. Box 25082, Oklahoma City, OK 73125-0082.
Note: Current FAA employees will not be appointed as designees until their employment with the FAA has ended. FAA employees may not apply to the NEB earlier than 120 days before their actual date of retirement or separation from the agency. Former FAA employees who submit an application within 3 years from the time their FAA employment terminated are exempt from the technical and character references. Appointments will be limited to functions performed while employed by the FAA, or other experience within the aviation industry. If a former FAA employee submits an application beyond 3 years from the date of termination, all application requirements apply.
(2) The NEB will review TPE applicants for the general requirements and rank the applicants who meet those requirements. The NEB will notify the applicant (by letter) of being placed in the candidate pool.
(3) The FSDO or IFO will notify the NEB when it has determined a need for, and possess the ability to manage a TPE. The NEB may be contacted via e-mail at: ‘9-AMC-AFS650-NEB/AMC/[email protected]
(4) When a FSDO or IFO accepts a candidate for designation, the NEB will send the candidate’s file to the appointing FSDO or IFO. The appointing FSDO or IFO will notify the candidate, and the candidate will schedule themselves to attend the Initial Technical Personnel Examiner Standardization Seminar (hereafter referred to as the Initial TPE Seminar).
Note: Candidates must successfully complete the Initial TPE Seminar before appointment as a designee.
(5) After the candidate successfully completes the Initial TPE Seminar, the candidate will provide the appointing FSDO or IFO with the Certificate of Completion from the Initial TPE Seminar.
(6) The appointing FSDO or IFO will complete the FAA Form 8000-5, Certificate of Designation, and FAA Form 8430-9, Certificate of Authority, for presentation to the designee.
Note: At the time of appointment, the FSDO or IFO should remind new TPEs that their signature on block 23 of Form 8110-28, is an acknowledgment that the designation as a TPE is a privilege, not a right, and the FAA Administrator can terminate any designation at any time or for any reason he or she deems appropriate.
b. Applying for Reinstatement. Examiners applying for reinstatement must submit the completed application, Form 8110-28, directly to the designating FSDO or IFO. The FSDO or IFO will determine if there is a need for the TPE, and if it possesses the ability to manage the TPE.
(1) Only the FSDO or IFO that previously had jurisdiction over the applicant may accomplish reinstatement without NEB review. If the TPE has been inactive for less than 24 calendar months, he or she must provide a current Certificate of Completion from a Recurrent Technical Personnel Examiner Standardization Seminar (hereafter referred to as Recurrent TPE Seminar) or an Initial TPE Seminar before reinstatement. Inactivity that exceeds the 24 calendar months will require the TPE to attend the Initial TPE Seminar before reinstatement.
(2) Former designees who relocate to another FSDO or IFO that request reinstatement will be treated as initial applicants. Such individuals must submit a completed application, Form 8110-28, to the NEB for initial evaluation, and recommendation as outlined in chapter 2, paragraph 1a.
(3) TPEs with a valid and current designation may relocate to a different geographical area. Provided there is no break in service and the receiving FSDO or IFO agrees to the transfer, TPEs may relocate without applying to the NEB. The TPE must submit a new application to the receiving FSDO or IFO.
c. Serve Outside the U.S. A TPE may be appointed to serve outside the U.S. provided such designation will serve U.S. citizens abroad and a supervising IFO can properly supervise the TPE’s activities. The TPE is subject to limitations as provided by current FAA policy regarding the certification of airmen outside the U.S.
2. General Requirements for Appointment. Inspectors must carefully consider all of the following issues before designating or renewing a TPE. The general requirements for appointment are:
a. A minimum age of 23 years.
b. Have a good record in the aviation industry with no violation history with the FAA (this does not include Administrative Actions or violations that have been expunged).
c. Have unquestionable integrity, a cooperative attitude, the ability to exercise sound judgment, be engaged in the industry and community, and have a reputation for dependability.
d. Have satisfactorily completed an Initial TPE Seminar before his or her appointment as a designee.
e. Have no known investigations, charged indictments, or pending actions in any local, state, or Federal court.
f. Have good knowledge of the pertinent regulations, directives, and related guidance material.
g. Have sufficient command of the English language, both oral and written, to allow the applicant to perform the authorized functions.
h. Be able to maintain the highest degree of objectivity while performing authorized functions.
i. For DME Appointment. The additional requirements are as follows:
(1) Show evidence of a high level of knowledge in the Subject Areas required for aviation mechanic certification in both reciprocating and turbine-engine aircraft.
(2) Have held a valid aviation mechanic certificate for 5 years with the rating(s) for which a designation is to be issued. When eligible persons are not available, the 5-year requirement may be reduced to 3 years if the prospective designee meets all other requirements, and possesses above average technical qualifications.
(3) Have been actively exercising the privileges of a valid aviation mechanic certificate for 3 years on U.S.-registered civil aircraft immediately before designation.
(4) Have a fixed base of operation adequately equipped to support testing in at least 25 percent of all level 1, level 2, and level 3 skill elements listed in the PTS under Objective 3 of each Subject Area, and be adequately equipped to support testing of all of the Core Competency elements listed in the PTS under Objective 2 of a Subject Area for the designation sought. This includes both reciprocating and turbine engine aircraft.
(a) The fixed base of operation, equipment, and materials must be adequate for an applicant to demonstrate the basic skills for the certificate and rating sought. The supervising FSDO or IFO will monitor the status of equipment periodically to ensure compliance.
(b) Use airworthy aircraft, other aircraft, aircraft subassemblies, operational mockups, or other aids for testing airman applicants.
(c) Tools, equipment, current publications, materials, etc., required to complete a project assignment must be the type recommended by aircraft manufacturers or accepted in the aviation industry.
j. For DPRE Appointment. The additional requirements are as follows:
(1) Evidence of a high level of knowledge in the Areas of Operation required for parachute rigger certification.
(2) Have held a valid master parachute rigger certificate for 2 years with the rating(s) for which the FSDO or IFO will issue a designation.
(3) Have been actively exercising the privileges of a valid master parachute rigger certificate for 2 years immediately before the designation.
(4) Have a fixed base of operation adequately equipped to support testing in each required Area of Operation for the designation held.
(a) The fixed base of operation, equipment, and materials must be adequate for an applicant to demonstrate the basic skills for the certificate and rating sought. The supervising FSDO or IFO will periodically monitor the status of equipment to ensure compliance.
(b) Tools, equipment, current publications, materials, etc., required to complete a project assignment must be the type parachute manufacturers recommend or accept in the industry.
(c) The fixed base of operation must, as a minimum, have tools and equipment necessary to perform, in each required Area of Operation, the Tasks the DPRE will assign as part of his or her developed test.
3. Delegation/Recision of a TPE Authorization. Title 49, of the United States Code § 44702 empowers the FAA Administrator to delegate to private individuals any function relating to the examination, inspection, and testing of airman applicants. These people are subject to any regulation, supervision, and review that the Administrator may prescribe. Under the provisions of this section and FAA directives, the Administrator may rescind any such delegation at any time and for any reason he or she deems appropriate. The Administrator may determine not to renew a delegation for any reason he or she deems appropriate.
Note: Nonrenewal is considered termination. Refer to chapter 6 for details regarding termination and appeal procedures.
Chapter 3. Training, Supervision, and Renewal
Chapter 3. Training, Supervision, and Renewal
1. Training. Before initial designation, prospective TPEs must satisfactorily complete the Initial TPE Seminar. (See appendix C for seminar information). Following the Initial TPE Seminar, personnel from the supervising FSDO or IFO must coach the TPE in all procedures relevant to the TPE’s duties before the TPE conducts any tests. The assigned inspector from the supervising FSDO or IFO should be present during the first oral and practical tests conducted by the TPE to provide guidance and training, and to inform the TPE of the proper test procedures. Specific emphasis items during training and indoctrination are:
a. Direction and Guidance. When necessary, the TPE is expected to call upon either the supervising FSDO or IFO for advice and guidance for the performance of assigned responsibilities in accordance with prescribed procedures.
b. Reference Materials. The TPE is expected to have ready access to the current FAA orders and regulations appropriate to airman certification.
c. Instruction. The TPE must receive specific instructions from the supervising FSDO or IFO in the proper conduct of oral and practical tests, the execution of the necessary forms, and the proper routing of certification files.
d. Availability. The TPE is expected to make his or her services available to all applicants on an equitable basis regardless of who trained the applicant or the applicant’s geographic area of residence.
e. Professional Conduct. Each TPE must represent the Administrator in a manner that will reflect positively on the FAA, and must exercise care with respect to the applicant, as follows:
(1) Honor appointments made as promptly as possible.
(2) Arrange to conduct the oral test in private with the applicant. In the instance where the TPE is allowed to test two applicants, conduct the oral test in private with one applicant at a time.
(3) Give undivided attention to the applicant during the testing period.
(4) Assure that discussion following any test is private and is confidential.
f. Proficiency. A TPE must maintain a high degree of knowledge in the Subject Areas required for airman certification and evaluation techniques.
2. Recurrent Training. Each TPE is encouraged to attend safety meetings, aviation seminars, and other programs that contribute to the techniques of aircraft maintenance or parachute rigging. TPEs must schedule themselves for a Recurrent TPE Seminar and notify the supervising FSDO or IFO. Satisfactory completion of the Initial TPE Seminar is a prerequisite for enrollment in a Recurrent TPE Seminar. Attendance at a Recurrent TPE Seminar is mandatory. The Certificate of Completion, which is issued to those that successfully complete a Recurrent TPE Seminar,
expires 24 months from the date shown on the certificate. (Refer to appendix C for seminar information.)
Note: The TPE must attend a Recurrent TPE Seminar every 24 calendar months or suspend certification activities until recurrent training is successfully completed. Upon successful completion of a Recurrent TPE Seminar, the TPE must provide a copy of the Certificate of Completion to the FSDO or IFO.
3. Supervision. Each TPE operates under the direct supervision of the FSDO or IFO that holds the designation file.
a. Resolve Questions. Upon request, inspectors who supervise the activities of TPEs must always welcome the opportunity to discuss procedures and standards with TPEs to resolve any questions. The supervising FSDO or IFO and/or the Designee Standardization Branch, AFS-640, should resolve TPE questions on issues that this order does not make clear.
b. Observe and Provide Oversight. Inspectors who supervise the activities of TPEs will observe each new TPE conducting oral and practical tests to determine that the TPE is familiar with current procedures and standards. Thereafter, each inspector with designee oversight responsibilities will inspect his or her assigned TPE(s) designated within the district.
c. Check Knowledge and Certification Files. The supervising FSDO or IFO will request a check of the TPE’s aeronautical knowledge and certification procedures when the performance of an applicant previously tested by a TPE is unsatisfactory, or other evidence reveals deficient performance by the TPE.
d. Submit Certification Files. TPEs must submit certification files to the supervising FSDO or IFO regardless of test results (pass, fail, or test not completed) within 5 calendar days of the test date.
4. Expiration. All first-time appointments will be for 1 year. At the discretion of the supervising FSDO or IFO the duration of subsequent designation periods will be from 1 to 3 years. All designations expire on October 31 of the year determined by the supervising FSDO or IFO, and will be indicated on Form 8430-9 issued to the TPE.
5. Renewal. A TPE’s designation will be renewed under the following conditions: the supervising FSDO or IFO determines that a need still exists; the FSDO or IFO still has the ability to manage the TPE; and the TPE continues to meet all the requirements for renewal. The FSDO or IFO must notify the TPE and issue a new Form 8430-9.
a. TPE Meetings. The supervising FSDO or IFO must hold an annual meeting to discuss TPE procedures, problems, and designation renewal. At the discretion of the manager of the supervising FSDO or IFO, this meeting may take place in conjunction with the Recurrent TPE Seminar.
b. Designee Maintains Designation. When conducting tests each designee must maintain the requirements for the designation, as listed in chapter 2, paragraph 2.
c. Satisfactorily Complete the Initial TPE Seminar. All TPEs must satisfactorily complete the Initial TPE Seminar.
d. Satisfactorily Complete the Recurrent TPE Seminar. In addition to completion of the Initial TPE Seminar, at the time of renewal, TPEs must have satisfactorily completed a Recurrent TPE Seminar within the preceding 24 calendar-months.
Note: Examiners may complete the Initial TPE Seminar in lieu of the Recurrent TPE Seminar to meet the recurrent training requirement of chapter 3, paragraph 5d.
e. Renewal File. The TPE must present a complete renewal file to the supervising FSDO or IFO 45 days before renewal. The TPE is responsible for completing the file for renewal. The file must include:
(1) The TPE’s current Form 8430-9.
(2) A record of all oral and practical tests conducted since the issuance or last renewal of their designation.
(3) A current certificate of training showing the TPE has successfully completed an Initial or Recurrent TPE Seminar.
(4) A new FAA Form 8110-28, Application and Statement of Qualification (DME/DPRE/DAR-T/ODAR-T), with blocks 1, 2, 4, 5, 6, 7, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 22, 23, and 23a completed.
Note: The signature on block 23 of Form 8110-28, acknowledges an understanding that the designation of TPE is a privilege, not a right, and that at any time, or for any reason the FAA Administrator deems appropriate, the designation may be terminated.
f. Supervising FSDO or IFO Completes Appropriate Blocks.
(1) The supervising FSDO or IFO will approve the application for renewal by completing the blocks 27(a) through (i) on page 4 of the Form 8110-28.
(2) The FSDO or IFO will issue Form 8430-9. The designee and the issuing inspector should each sign Form 8430-9. Enter the jurisdictional district office number on the reverse side.
g. Retain Application in Office Files. After completing the application for renewal, FSDO or IFO personnel will retain the completed renewal file as required by FAA Order 1350.15, Records Organization, Transfer, and Destruction Standards, as revised.
h. Enter the information into the Vital Information Subsystem (VIS). Verify that the information is correct. If you have any questions, you may contact the Aviation Data Systems Branch, AFS-620.
6. Knowledge and Skill. The determination that the TPE’s knowledge and application of current procedures and standards are adequate for renewal of the designation may be based on the TPE’s attendance at a meeting or seminar conducted for the purpose of standardization. At the discretion of the supervising FSDO or IFO, it may be necessary for an appropriately rated inspector to observe a TPE conduct an oral and/or a practical tests. For uncompromised safety, it is important that the TPE require a high, but achievable level of competence from qualified applicants.
Chapter 4. Privileges and Limitations
Chapter 4. Privileges and Limitations
1. Privileges. Authorize a TPE to:
a. Accept FAA Form 8610-2, Airman Certificate and/or Rating Application, for airman certificates and ratings.
b. Conduct oral and practical tests appropriate to FAA Form 8430-9, Certificate of Authority, held by the TPE.
c. Charge each applicant a reasonable fee. The TPE should ensure the applicant understands all fees charged, including the fee for retesting after failure, before the TPE accepts Form 8610-2.
d. Issue temporary airman certificates to applicants who have been tested and found qualified for the certificate or rating sought. The supervising FSDO or IFO may retain this privilege.
e. Aviation Maintenance Technician School (AMTS)-affiliated DME: (Refer to chapter 5, paragraph 2c.) Affiliated DMEs may test two applicants at a time provided they are either students (Title 14 of the Code of Federal Regulations (14 CFR) part 65, § 65.80) or graduates of that AMTS.
2. Limitations. A TPE must not:
a. Conduct oral and practical tests at locations not listed as a base of operation on the current Form 8430-9 held by the TPE, unless authorized by the supervising FSDO or IFO.
b. Conduct or monitor any portion of computer knowledge tests.
c. Reissue or amend any expired FAA Form 8060-4, Temporary Airman Certificate.
d. Endorse, amend, alter, or issue any permanent airman certificate.
e. Exempt any aviation mechanic applicant from testing in all Subject Areas of the Sections required for the rating sought; or exempt any parachute rigger applicant from testing in all Areas of Operation required for the rating sought.
f. Combine teaching with testing while testing an applicant.
g. Conduct oral and practical tests unless an applicant presents proof of eligibility as prescribed in part 65.
h. Conduct oral and practical tests at the base of operation that appears on the TPE’s Form 8430-9 unless it is adequately equipped with available equipment and material necessary for conducting the tests.
i. Conduct oral and practical tests unless the applicant has passed the required computer knowledge test(s).
Note: This does not apply to aviation mechanic applicants authorized to test in accordance with § 65.80, or master parachute rigger applicants that hold a senior certificate.
j. Conduct oral and practical tests for applicants that have been authorized to test on block V of Form 8610-2 by an inspector in a FSDO or IFO other than the TPE’s responsible FSDO or IFO, unless:
(1) The TPE reports the request for testing to the FSDO or IFO responsible for his or her designee authorization.
(2) The TPE receives written permission before conducting the test. The TPE may be issued continuing authorization to perform these tests. This authorization does not relieve the TPE from the notification requirements of chapter 5, paragraph 1 before performing the test. Any time it finds necessary, the TPE’s responsible FSDO or IFO may amend or rescind the continuing authorization.
Note: This paragraph is intended as a limitation for the TPE. An applicant is not required to present his or her application to the local FSDO or IFO for reauthorization unless there is evidence that his or her original authorization is in question.
k. Temporarily suspend a test to allow the applicant further study, and then continue the same test later.
l. With the exception of chapter 4, paragraph 1e, a TPE may only test one applicant at a time.
m. Deviate from the procedures in this order or the PTS.
3. Geographical Area.
a. Administer Test Outside Geographical Area. TPEs who want to administer oral and practical tests outside the geographical area of their supervising FSDO or IFO must:
(1) Request authorization in writing from the supervising FSDO or IFO and the FSDO or IFO in the district where the tests will be conducted.
(2) Provide these FSDOs or IFOs with the date and address of the testing site in writing.
(3) Make the request in a timely manner before the test date.
(4) Arrange for, and prove to the FSDO or IFO in the district where the temporary test site is located, that the TPE has available adequate facilities, equipment, current publications, and materials for testing applicants to demonstrate the basic skills necessary for the certificate and/or rating(s) sought.
(5) Requests to test outside the TPE’s respective regional geographic area will be denied.
b. Permission Granted. When granting permission to the TPE to administer oral and practical tests in the area of jurisdiction of another FSDO or IFO:
(1) The TPE then comes under the jurisdiction of that FSDO or IFO.
(2) Submit certification files to that FSDO or IFO.
Chapter 5. Conducting and Grading Tests
Chapter 5. Conducting and Grading Tests
1. Preparation. TPEs must notify the supervising FSDO or IFO before conducting all oral and practical tests. The supervising FSDO or IFO may establish specific procedures for this notification. Because applicants may have widely differing backgrounds, it will be necessary to review the applicant’s experience in order to select appropriate oral questions and practical projects. The TPE asks questions and assigns projects that will be fair and cover all Subject Areas necessary for certification.
a. Charge a Reasonable Fee. The TPE may charge a reasonable fee to each applicant for handling the forms and reports incidental to the issuance of an aviation mechanic certificate, and for the use of the TPE’s facilities, equipment, materials, and services in administering the oral and practical tests. The TPE and the applicant should reach a mutual understanding and agree on the total fee for the TPE’s services before beginning the tests. An agreement in writing may be advantageous to both the TPE and the applicant.
b. Knowledge and Skill Elements. Use the knowledge (oral) and skill (practical) elements listed in the PTS to administer the oral and practical tests. It is essential to forward a copy of all knowledge element questions and skill element test projects developed by the TPE to the supervising FAA district office. Unless otherwise authorized by the supervising FSDO or IFO, the TPE must forward the questions and/or projects to the FAA at least 30 days before their use in an oral and practical test.
(1) For the DME: Subject Area. Test in each Subject Area of each Section required for the rating sought; one-third of the Section must be level 1 or higher, one-third must be level 2 or higher, and one-third must be level 3, even though the applicant may not have used some of the skills in past or present jobs. The DME is not required to test every element in each Subject Area. An applicant must be able to demonstrate satisfactory knowledge and skill in the assigned elements in each Subject Area to the required standard.
(2) For the DPRE: Area of Operation. Test in each Area of Operation required for certificate/rating sought. An applicant must perform satisfactorily in each selected Task in each required Area of Operation. In addition, an applicant must complete one parachute pack for each rating he or she seeks.
c. Developing Knowledge (Oral) Element Tests. This type of questioning intends to measure an applicant’s basic knowledge of a Subject Area. The design of the knowledge question is directly related to the accuracy of this measurement.
(1) For the DME: The DME may continue to develop and use knowledge element questions. Use the guidelines from paragraph 1c(2) below, to assist in the development of questions. The DME may also use questions obtained from the Airman Testing Standards Branch, AFS-630, internet based knowledge question data bank located at: http://www.faa.gov/about/office_org/headquarters_offices/avs/offices/afs/afs600/afs630/. Select developed and/or downloaded questions applicable to the type of test to be administered. Do not select more than 10 questions for each Subject Area to be tested. Do not use the same questions for three consecutive tests. Do not allow an applicant to select questions.
(2) The TPE should use the following basic guidelines to assist in developing knowledge questions.
(a) The knowledge questions should be:
• Clear. Content should establish the conditions or significant circumstances so the TPE and the applicant will have the same mental picture.
• Grammatically correct.
• Concise. Long questions can be complex and ambiguous.
• Pertinent to the skill element when combining knowledge (oral) and skill elements.
• Have only one correct answer.
(b) The questions should not:
• Be open-ended or multichoice questions.
• Require any further information or clarification.
• Be manufacturer specific.
• Contain double negatives.
• Have two parts.
• Contain clues to the answer.
(c) Knowledge questions should be limited only to either who, what, when, where, how, or why, not a combination. The questions should challenge the applicant enough so that the TPE can properly evaluate the applicant’s basic knowledge. Answers to the knowledge questions must be found within FAA-approved or accepted information sources (e.g., advisory circulars (AC), orders, or Federal aviation regulations).
d. Develop Skill (Practical) Element Projects. The objective of this type of test is to measure an applicant’s basic skills in a Subject Area. The design of the skill element is directly related to its assigned level and to the accuracy of this measurement. Use the following basic guidelines to assist in the development of skill projects.
(1) Include any materials (e.g., specific tools, equipment, mock-ups, and technical data) that will be required for the project.
(2) Be clear and concise with the level clearly identified.
(3) Refer to the standard(s) by which the project will be graded. The TPE must develop a performance standard for each project and include:
(a) What the Applicant Must Do. As an example: (for mechanic applicants) install an assigned control surface; (for parachute rigger applicants) inspect a pilot chute.
(b) How it Must Be Done. As an example: use of proper information (e.g., manufacturer’s data, Type Certificate Data Sheets (TCDS)), proper tooling, and observance of all applicable safety precautions.
e. Assign Unique Identifier. The TPE must assign a unique identifier to each knowledge element question and skill element project developed.
f. Prescribed Length of Time. There is no standard length of time prescribed for oral and practical tests. The testing period must, however be long enough to make a valid determination in each Subject Area or Area of Operation for the rating sought. Take appropriate time to ensure that all required knowledge element questions and skill element practical projects have been completed for the rating sought.
g. Two Originals. The applicant submits two originals of FAA Form 8610-2, Airman Certificate and/or Rating Application, before testing begins. The applicant must complete Form 8610-2 in accordance with appendix A. The TPE or inspector should provide Form 8610-2 and give detailed instructions for completing it correctly. The inspector or TPE must copy appendix A and provide it to the applicant until Form 8610-2 is revised with written instructions attached. Advise the applicant to read the supplemental information attached to Form 8610-2. (Refer to appendix A, Figure A-1.)
Note: All signatures must be original with the name printed or typed below or next to the signature. Use dark ink for the printed name and signature.
h. Conduct a Pretest Interview. The TPE should accomplish the interview either face to face, by telephone/fax, through e-mail, or other methods that will allow the TPE to:
(1) Discuss fees, testing procedures, projects, and type of equipment to be used and what the applicant should expect if he or she passes, fails, or does not complete the test.
(2) Advise the applicant when the day’s activities end, and when testing resumes if more than 1 day is needed.
(3) Ensure the applicant’s eligibility. (See chapter 5, paragraph 2.)
(a) Review the applicant’s Form 8610-2 for completeness and correctness. The TPE must have the applicant correct any errors. This may require the applicant to return to the FSDO or IFO where authorization was obtained.
(b) Review the applicant’s current written test results that are applicable to the rating(s) sought.
(c) When applicants pass all of their required tests, have them indicate their responses to the two questions listed in Block IV, Applicant’s Certification, on the reverse side of Form 8610-2. There may be a need to have supervising FAA district office involvement if the applicants would be required to answer “Yes” to either of the questions.
i. Progressive Tests Must Not Be Given. Although it may be necessary to continue a test for more than 1 day, tests must not be allowed to continue for long periods. Progressive testing is defined as testing which continues for more than four sessions in a 4-day period. Suspending the test to allow the applicant further study is not allowed. Both the applicant and the TPE should plan the testing times so that the applicant completes most of the test once it commences.
j. Test Not Completed in Allotted Timeframe. Should the test not be completed in the allotted timeframe, the TPE will correctly mark both 8610-2 forms (two originals) on the reverse side. Forward this incomplete test file to the supervising FSDO or IFO within 5 calendar days. When practical, schedule a retest for the areas not completed at the time the test is discontinued. Treat this retest as if the applicant had failed those portions not tested. (Refer to chapter 5, paragraphs 2d and 2e.)
(1) For the DME: Correctly mark the Subject Areas completed. Incomplete Subject Areas will not be marked as a failure on Form 8610-2 (two originals). In addition, place a statement in the “Remarks” area indicating why the test was not completed.
(2) For the DPRE: Do not mark as a failure. On both copies of Form 8610-2, place a statement in the “Remarks” area indicating why the test was not completed.
Note: Do not start any test without the intent to complete the testing for the issuance of a certificate and at least one rating or an added rating.
k. For the DME: The General Section of the Tests. Never test with the intent of testing the General section only. Applicants for an airframe rating must take Sections I, II, and III. Applicants for a powerplant rating must take Sections I, IV, and V.
(1) An applicant is not required to take Section I, General, of a knowledge or skill test for a mechanic rating if it was previously passed. Proof of passing may be in either of the following forms:
(a) A mechanic certificate with the alternate rating.
(b) FAA Form 8610-2 that shows Section I, General, has been passed within the preceding 24 calendar-months (although other Sections may not have been passed).
2. Applicant Eligibility.
a. Furnish Current, Government-Issued Identification. Applicants must furnish current, government-issued identification with a photograph and signature. If Form 8610-2 is completed at a FSDO or IFO, the approving inspector will record the method of identification (e.g., driver’s license, passport, military identification), number, and expiration date in the “Remarks” area of Form 8610-2. The TPE will verify the applicant’s identification before testing. If the means of
identification was provided in the “Remarks” area, the TPE will verify the identification and initial the inspector’s entry. (Sample Entry: Oklahoma Driver’s License #123456789 exp. 01/31/2010.) If the means of identification was not previously entered in the “Remarks” area or the means of identification provided by the applicant is different from the one listed in the “Remarks” area, the TPE will make the entry in the “Remarks” area and initial the entry. (Mechanic applicants should refer to appendix D, Figures D-6 through D-11; parachute rigger applicants should refer to appendix E, Figures E-3 through E-5.)
b. Meet English Language Requirements. The TPEs and inspectors share the responsibility for ensuring applicants meet the English language requirements. (Before accepting the application and beginning the practical test for certificate or rating, the TPE and inspector must evaluate the applicant’s English fluency using the appropriate guidance.) AC 60-28, English Language Skill Standards Required By 14 CFR parts 61, 63, and 65, provides guidance for airman applicants, TPEs, and inspectors in determining English language skills required for airman certification.
c. Original FAA Form 8610-2.
(1) All applicants claiming civilian and/or military experience as a basis for qualification must have their experiences evaluated and verified by an inspector before taking the required test. The inspector may, as a matter of office procedures, reproduce and retain copies of Form 8610-2 and documented evidence presented by the applicant. The inspector will:
(a) Evaluate and, if necessary, verify the documented experience.
(b) Have the applicant complete Form 8610-2 (two originals). (Refer to appendix D, Figures D-1, D-2, D-4, and D-5; and appendix E, Figures E-1 and E-2.) Provide a copy of appendix A to the applicant. Instruct the applicant to read and detach, if necessary, the “Privacy Act” area of the form.
(c) Review the form for completeness, sign and complete block V (both originals), and return them if the applicant meets the experience requirements. Return all experience documents to the applicant. The applicant must retain both originals for presentation to a TPE or inspector for the oral and practical tests.
Note: The block V endorsement must not be restricted to a specific district office or region.
(d) Only Maintenance or Avionics inspectors who hold the mechanic certificate with an Airframe and Powerplant rating are authorized to review and endorse block V of Form 8610-2.
Note: Graduates of an Aviation Maintenance Technician School (AMTS) may take the applicable knowledge test upon presenting an appropriate graduation certificate or Certificate of Completion to an affiliated test center. Other applicants may take the applicable mechanic test upon presenting a Form 8610-2 that has been endorsed in block V by an inspector and indicates the test(s) authorized to be administered.
(2) For the DME: Applicants attending or graduating from an approved AMTS.
(a) Affiliation. It is not necessary that graduates from AMTSs having affiliated DMEs present to the local inspector their graduation certificates or Certificates of Completion appropriate to ratings sought before taking the computer knowledge test and oral and practical tests provided:
1. The AMTS has an affiliated computerized testing center and an affiliated DME, and the affiliated DMEs give the tests.
2. The AMTS has established a procedure acceptable to the supervising FSDO having jurisdiction over the AMTS. This procedure will require that the AMTS provide a certified list of graduates to the FSDO and to each of the AMTS’s affiliated computerized testing centers, and DMEs. The list must be available before the computerized testing center or DMEs begin administering the appropriate test(s). The AMTS will maintain and provide a current list of affiliated computerized testing centers and DMEs to the FSDO.
3. The AMTS’s certified list must contain the names and addresses of graduates, graduation dates, and the curriculum from which the applicant graduated (e.g., airframe, powerplant, or airframe and powerplant combined.) The list will reflect a statement certifying these graduates and will be signed and dated by an authorized AMTS official.
Note: Graduates taking the written or oral and practical tests from DMEs, other than those affiliated with the AMTS, must present a graduation certificate or certificate of completion to an inspector. This also applies to nonaffiliated computerized testing centers. (The inspector must review the documents, complete block V and sign it. This authorizes the AMTS graduate to be tested by a DME other than an AMTS-affiliated DME.)
4. Affiliated AMTS DMEs may administer oral and practical tests to graduates/applicants, without an FAA signature in block V of Form 8610-2 only when a graduation certificate or certificate of completion is presented and the AMTS provides the DME with the certified list of graduates.
5. Applicants must complete Form 8610-2 (both originals).
6. Affiliated DMEs must review Form 8610-2 to determine and ensure that it is complete and correct. They should verify that the applicant meets the requirements of part 65, §§ 65.11, 65.12, and 65.71, before issuing FAA Form 8060-4, Temporary Airman Certificate. The applicant will present an appropriate computerized test report(s). All Sections of the computer knowledge test must have been passed within the previous 24 calendar-months except when the applicant is authorized to take an early oral and practical test by part 65, § 65.80.
(b) Testing Under § 65.80. AMTS students may be authorized by the supervising FSDO to take the oral and practical tests before the computer knowledge test in accordance with § 65.80.
1. Each student must complete the front of Form 8610-2 (both originals). The form must show the AMTS’s name and location (block II, item D1), AMTS’s certificate number (block II, item D2), curriculum in which student is enrolled (block II, item D3), and graduation date (block II, item D4). Applicants should not check block II, item D, Graduate of Approved Course. (Refer to appendix A, Figure A-4.)
2. AMTSs must show that each student is in the final phase of training and has maintained satisfactory progress at the school.
Note: The student must be within 45 school days of completing that phase of the curriculum. If enrolled in the Airframe only or Powerplant only, must have completed the General and be within 45 school days of completion for the Airframe or Powerplant. If the applicant is enrolled in the Powerplant, and has completed the General and Airframe, he or she must be within 45 school days of completion of the Powerplant curriculum. If the student is enrolled in the combined Airframe and Powerplant, he or she must be within 45 school days of completing of the entire curriculum for the combined Airframe and Powerplant, has made satisfactory progress, and is prepared for the test. The proper AMTS official must complete block II, item E, (1) and (2).
3. Inspectors must complete block II, item F, (1), (2), (3), and (4). (Refer to appendix A, Figure A-4.) The FAA authorization expiration date must not be later than the anticipated graduation date. Process the completed file through the supervising FSDO. (The supervising FSDO has authorized testing of any student by a nonaffiliated DME by completing block II, item F, (1), (2), (3), and (4).)
(3) For the DPRE: Senior, Master, Added ratings and Military.
(a) Senior parachute rigger applicants for an original certificate must show proof to an inspector or a DPRE of having passed the parachute rigger computer knowledge test (RIG) by presenting a computerized test report. (Refer to appendix E, Figure E-7.)
(b) Master parachute rigger applicants for an original certificate:
1. An applicant who does not hold a senior certificate must show proof to an inspector or a DPRE of having passed the RIG by presenting a computerized test report.
2. An applicant who holds a senior certificate must present the airman certificate to the DPRE. No knowledge test is required.
(c) Adding a Rating. An applicant must present his or her senior or master certificate to the DPRE. No knowledge test is required.
(d) Military Parachute Riggers. Current and former military parachute riggers may be tested in accordance with part 65, § 65.117 at a computer testing center.
d. Retests. When application is made for a retest after failure of a previous test or incomplete test, the applicant must:
(1) Complete Form 8610-2 (both originals) in accordance with the instructions the TPE or inspector furnishes.
Note: Form 8610-2, block V does not need to be signed by an inspector if a copy of the original form (with authorizing signature) is attached to the file.
(2) Present an appropriate computerized test report. All Sections of the computer knowledge tests must have been passed within the previous 24 calendar months.
(3) Present his or her original of Form 8610-2 from the previous oral and practical tests showing the Sections or Areas of Operation failed, not completed, or for which passing credit has expired (mechanic applicants only).
(4) If the retest is within 30 days of the previous test, present a statement by a person authorized in part 65, § 65.19 that the applicant has received additional instruction for each subject failed and that the applicant is ready for retesting. This statement of training is required only when the applicant failed portions of the test. (Refer to appendix D, Figure D-14, and appendix E, Figure E-6.)
Note: This statement of training is not required for Subject Areas not completed on the previous test.
e. Test in all required areas. Test applicants for retest in all areas of the oral and/or practical tests in the Section(s) or Area(s) of Operation listed as failed, that was/were not taken, or that has/have expired.
(1) For the DME: Applicants who apply for retesting within 60 days to the same DME who gave the failed test may, at the option of the DME, be tested in only the Subject Areas failed on the previous test provided the applicant has successfully passed all other Subject Areas within that Section. (New questions and practical projects may be included in the retest.). Retest practical projects must be at the same level as failed.
(2) For the DPRE: Applicants who apply for retesting within 60 days to the same DPRE who administered the failed test may, at the option of the DPRE, be tested in only the Task(s) failed or that were not taken on the previous test, provided the applicant has successfully passed all other Tasks.
Note: During a retest, and at the discretion of the DPRE, any Task may be reevaluated, including those previously passed.
3. Evaluating Applicant Performance. Do not expect an applicant to be competent in all phases of overhaul, maintenance, alteration, and repair, or be highly skillful in performing complex manipulative operations. However, expect the applicant to have developed basic skills and should demonstrate them during the practical test. Inform the applicant of the level of performance expected before beginning each project. DMEs can find the required performance levels in the PTS. DPREs should inform their applicants that they must demonstrate an approval for return to service proficiency on the assigned Tasks.
a. For the DME: When it becomes obvious during the test that an applicant cannot perform at an acceptable level and has already failed:
(1) Section. When it becomes obvious during the test that an applicant cannot perform at an acceptable level and has already failed several Subject Areas in a Section, the DME may stop testing in that Section and go to the next Section. In some cases, however, it may be advantageous to continue to the end of the Section so the applicant will know his or her strengths and weaknesses when preparing for retest. After stopping testing in a Section, the DME will make an appropriate note in the “Remarks” area on the reverse side of Form 8610-2.
(2) Subject Area. When it becomes obvious during the test that an applicant cannot perform at an acceptable level and has failed a Subject Area, the DME may stop testing in that Subject Area and go to the next. The DME or the applicant may stop the testing any time after the failure of a Subject Area. Several Subject Areas may be evaluated during an assigned practical project. In any case, the applicant is entitled to credit for only those Subject Areas satisfactorily completed.
b. For the DPRE: When it becomes obvious during the test that an applicant cannot perform at an acceptable level and has already failed:
(1) Area of Operation. When it is obvious during the test that an applicant cannot perform acceptably and has already failed an Area of Operation, the DPRE may stop testing in that Area of Operation and go to the next. There is no maximum number of projects the DPRE may evaluate in an Area of Operation. In some cases it may be advantageous to complete an already failed test so the applicant will know his or her strengths and weaknesses when preparing for a retest.
(2) Tasks. When evaluating an Area of Operation with more than one Task assigned and it becomes obvious during the test that an applicant cannot perform at an acceptable level and has already failed one of the assigned Tasks, the DPRE may stop testing in that Area of Operation or go on with the next Task. The DPRE or the applicant may discontinue the testing any time after the failure of a Task. In any case, the applicant is entitled to credit for only those Tasks satisfactorily completed.
Note: If testing for a certificate/rating was terminated, the DPRE will make an appropriate note listing the Area(s) of Operation and associated Task(s) failed, or not completed, in the “Remarks” area on the reverse side of Form 8610-2.
c. Standards. Include the following standards in TPE observations for evaluating applicant performance:
(1) Approach to the project; proper information and tools; preparation of the equipment; and observation of safety precautions.
(2) Cleaning, preparing, and protecting parts; skill in handling tools; thoroughness and cleanliness.
(3) The functions of the units or systems of the assigned project; use of current maintenance and/or overhaul procedures.
(4) Final inspection for safety and operation.
(5) Completion of required forms and records.
(6) Application of appropriate rules.
(7) Attitude toward safety, manufacturer’s recommendations, and acceptable industry practices.
4. Conducting the Tests.
a. Conducting the Oral Test.
(1) Oral questioning may be used at any time during the practical test.
Note: In instances where the DME is allowed to test two applicants, the oral test must be conducted privately with one applicant at a time.
(a) For the DME: Ask at least four questions in each Subject Area. These questions should be from more than one element listed under Objective 1 in the PTS for that Subject Area. The applicant must be able to successfully answer 70 percent of the oral questions asked in each Subject Area. Each Subject Area must be passed in order to pass a Section.
Note: Use no more than 10 questions to evaluate a Subject Area.
(b) For the DPRE: At minimum quiz, the applicant on each knowledge element for each objective in a selected Task. The minimum passing grade is 70 percent of the number of knowledge questions asked in each selected Task. Applicants must pass each Task to pass the Area of Operation. The DPRE is not required to use oral questions for skill-only Tasks.
(2) An applicant’s answers to oral questions must show an understanding of the subject and ability to apply knowledge. Do not allow an applicant’s skill of oral expression or ability to memorize details affect the oral test evaluation. If necessary, additional exploratory questions may be used to verify the applicant’s understanding of the subject area.
(3) To determine if the oral questions are answered correctly, the TPE must be able to reference information (e.g., manufacturer’s data, ACs, CFRs). The TPE must be objective in making the determination.
(4) Although the answers to the oral questions should be available in the CFRs, manufacturer’s maintenance data, or other aviation-related data, the applicant must be able to successfully answer all oral questions without the use of any reference materials.
b. Conducting the Practical Test.
(1) For the DME: All Subject Areas required for the rating sought must be tested; however, the DME is not required to test every element in each Subject Area.
(a) In Subject Areas where core competency is identified (Objective 2 of the Subject Area), the DME must test the applicant on the core competency element and at least one other skill element selected from Objective 3 of the Subject Area. The minimum passing grade for each Objective is 70 percent. If an applicant fails an Objective, the examiner may, at his or her discretion, provide three additional projects from the failed Objective. The applicant must successfully complete the additional projects to meet the minimum passing grade. Each Subject Area must be passed to pass a Section. Combine Subject Areas and/or elements as needed to facilitate the taking of the test.
(b) The DME must personally observe all practical projects performed by the applicant.
(c) The DME must determine if the applicant’s project is acceptable. Be objective in making this determination. The applicant must be able to demonstrate satisfactory proficiency and competency using basic aircraft mechanic skills. The applicant must demonstrate an approval for return to service standard (where applicable), and demonstrate the ability to locate and apply the required reference materials (where applicable). For instances where an approval for return to service standard cannot be achieved, the applicant must be able to explain why the return to service standard cannot be met (e.g., when tolerances are outside of a product’s limitations).
(d) Applicants for powerplant ratings must show the ability to make satisfactory minor repairs and alterations to propellers.
(e) The DME must provide all tools, equipment, and reference materials for the Subject Area elements selected. These materials must include, but are not limited to: 14 CFR, TCDSs, Airworthiness Directives (AD), ACs, manufacturer’s technical and parts manuals, service information, and any other instructions and/or reference materials that are necessary for the objective accomplishment of the assigned Subject Area element(s). All reference material must be unmarked and in good condition. The applicant’s use of other reference material, not provided by the DME, is prohibited. Use of nonprogrammable calculators is permitted where appropriate. Applicants may use personal tools and equipment at the discretion of the DME.
(2) For the DPRE: The DPRE must test the applicant in each Area of Operation that corresponds with each certificate and/or rating the applicant seeks.
(a) In areas where a selected Task is identified, the examiner must test the applicant on that Task and may select additional Tasks, if necessary. DPREs must evaluate all selected Tasks in their entirety. The applicant must pass each Area of Operation required for the rating(s) sought.
(b) The DPRE may combine Area of Operation and/or Task elements to facilitate testing.
(c) The DPRE must physically observe all tasks the applicant performs.
(d) The DPRE must objectively determine if the applicant’s project is acceptable. The applicant must demonstrate proficiency and competence using basic skills. Where applicable, the applicant must demonstrate an approval for return to service standard, and the ability to locate and apply the required reference materials. For instances where an approval for return to service standard is not achievable, the applicant must explain why the standard cannot be met (e.g., tolerances that are outside the manufacturer’s limitations).
(e) The minimum passing grade is 70 percent. If an applicant fails a Task, it is at the examiner’s discretion to provide three additional projects from the failed Task. The applicant must successfully complete the additional projects to meet the minimum passing grade.
(f) The DPRE must provide all tools, equipment, and reference materials to support the test. These materials must include, but are not limited to, Federal aviation regulations, ADs, ACs, manufacturer’s technical and parts manuals, service information, and any other instructions and/or reference material that are necessary for the objective accomplishment of the assigned Task(s). All reference material must be unmarked and in good condition. The applicant may not use reference material the DPRE has not provided. The applicant may use nonprogrammable calculators where appropriate. Applicants may use personal tools and equipment at the discretion of the DPRE.
(g) Oral and Practical Test Variations. DPREs must conduct the oral and practical test as follows:
1. Original Issuance of a Senior Rigger Certificate. The DPRE must select at least one Task from each Area of Operation, except Area VII. In Area III, the DPRE will select the corresponding packing task for each rating the applicant requests.
2. Original Issuance of a Master Rigger Certificate to a Noncertificated Applicant (Applicant Not Holding a Senior Certificate). The DPRE must select at least two type rating tasks from Area of Operation III, two tasks from Area VII, and at least one Task from each of the other areas.
3. Original Issuance of a Master Rigger Certificate to the Holder of a Senior Certificate. If the senior applicant holds two or more ratings and is not requesting any additional rating(s), the DPRE must select one Task from each Area of Operation, except in Area VII where two Tasks are required. In Area III, the DPRE should select one of the alternate packing tasks, item E, F, or G. The DPRE may, at his or her discretion, require the applicant to demonstrate the packing of any type rating the applicant currently holds. If the senior applicant holds one rating, the DPRE must select one task from each of the Areas of Operation, except in Area VII where two Tasks are required. From Area III the DPRE must select the Task for the type rating that the applicant seeks.
4. Additional Ratings. For an added rating to either a senior or master certificate, the DPRE must test the applicant from Area III on the added rating sought. The DPRE may, at his or her discretion, require the applicant to demonstrate any additional Task(s) appropriate to the added rating sought.
5. For Military Competency Test. No practical test is required, only a knowledge test.
5. Test Planning Sheets Are Required for Each Oral and Practical Test Given. Forward test planning sheets to the supervising FSDO or IFO with the certification file. Retention of test planning sheets by the FSDO or IFO is in accordance with Order 1350.15, Records Organization, Transfer, and Destruction Standards (as revised). Appendix F includes an example of a planning sheet. Planning sheets developed by the TPE must contain the information included in the appendix F example (both sides). The local FSDO or IFO may also require additional information on the planning sheets. Mark the planning sheets for each knowledge (oral) element question and skill (practical) element project that will be assigned. If the planning sheet in appendix F is used, the TPE must make copies of both sides.
Note: The applicant’s signature on the planning sheet is to verify that the test was given to the applicant and that the test times and dates listed were actual. Because testing material is controlled, it is not intended that the signature infer that the applicant has verified specific information which appears in Block V of Form 8610-2.
6. Recording the Results of Tests. Record the results of oral and practical tests on the reverse side of Form 8610-2.
a. For the DME: When the applicant has demonstrated an acceptable level of competence, workmanship, and safety in each Subject Area , check the “Pass” box for that portion of the Section (oral or practical test) and enter the expiration date; otherwise, check the “Fail” box, but do not enter a date when the applicant fails. Make all entries in permanent dark ink. See chapter 5, paragraph 9 for procedures to follow if an applicant fails.
(1) The expiration date for each oral and practical test Section is 24 calendar-months after the Section is passed. (Example: A test Section passed on any day in August 2007 will expire on August 31, 2009.)
(2) Do not code any knowledge (oral) element questions or skill (practical) element projects on the reverse side of Form 8610-2 unless the oral or practical test in a Section has been failed.
b. For the DPRE: Record the final results of oral and practical tests on the reverse side of Form 8610-2. When the applicant has demonstrated an acceptable level of competence, workmanship, and safety, check the “Pass” box for that rating, or check the “Fail” box if the applicant has not demonstrated an acceptable level of competence. Make all entries in permanent ink. Follow the procedures listed in chapter 5, paragraph 9 if an applicant fails.
Note: For an incomplete test with no failed Task(s), do not check “Pass” or “Fail.”
7. When the Applicant Passes. When the applicant has passed all the required Sections of both the oral and practical tests, the TPE who administered the test must:
a. Complete the reverse side of Form 8610-2 as follows:
(1) Date. Enter the date the test was completed, sign the form, and enter his or her designation number in the spaces provided on the reverse of Form 8610-2 (both originals).
(2) Applicant’s Certification. Require the applicant to complete the “Applicant’s Certification” area on the reverse side of Form 8610-2 (both originals), following the Designated Examiners Report. Use the “Applicant’s Certification” area to verify that the applicant still meets the conditions and requirements of §§ 65.11 and 65.12.
Note: At the time of issuance of Form 8060-4, the inspector and/or the TPE must request a telephone number where the applicant may be reached during the next 120 days in the event of application problems. The telephone number must be recorded in the “Remarks” area on the back of the application. If a telephone number is not available, write “No Telephone.”
b. Original. Give one original of Form 8610-2 to the applicant.
c. Temporary Airman Certificate. Prepare FAA Form 8060-4, Temporary Airman Certificate, unless otherwise directed by the supervising FSDO or IFO (refer to appendix D, Figures D-12 and D-13; and appendix E, Figures E-8 through E-10). Issue the duplicate copy to the applicant. Forward the original typed copy with the certification file to the local FSDO or IFO. Ensure that Form 8060-4 reflects the applicant’s current information. Substantiating documentation must be attached to the certification files for changes in the applicant’s name, gender, nationality, and/or date of birth.
Note: For a name change, the applicant must provide copies of appropriate documents verifying the name change, such as a court order, marriage license, divorce decree, or other state-approved documents. For a gender change, the applicant must provide a copy of the court order, or a statement from a physician or clinical psychologist verifying the applicant is undergoing treatment that has or will alter the applicant’s gender. For a change in nationalization, the applicant must provide the name and location of the court, the date of naturalization, and the docket number. Do not copy the naturalization papers under any circumstances. For a change in the date of birth, the applicant must provide a copy of an amended birth certificate or other state-approved document.
(1) Entries for the applicant’s copy may be printed in ink; however, a typed original signed by the issuing TPE must accompany the certification file, which must be forwarded to the supervising FSDO or IFO. The applicant need not sign the copy sent to the FSDO or IFO.
(2) The Airmen Certification Branch, AFS-760, will issue all original airman certificates with a unique certificate number during the processing of the airman file. The airman’s Social Security Number (SSN) can still be collected on Form 8610-2, but the word “Pending” must be placed in the certificate number block III of Form 8060-4. If the airman does not wish to provide his or her SSN to the FAA, the applicant must place the words “Do not use” in the SSN block of the application. Airman certificates presently using the SSN as a certificate number will continue to be issued with that number unless the applicant requests a unique number. If the airman
requests a unique number when applying for an added rating, the word “Pending” must be placed in the certificate number block of Form 8060-4.
d. Authorized under § 65.80. If the applicant has been authorized under § 65.80 to take the oral and practical tests before the computer knowledge tests and passes them:
(1) On the reverse side of Form 8610-2 under the “Remarks” area, put the following statement: “Temporary certificate was not issued.” Give the applicant a completed and signed original of Form 8610-2. This original will be needed when the applicant applies for a certificate after passing the computer knowledge tests.
(2) Send the applicant’s other signed original of Form 8610-2 to the supervising FSDO within 5 calendar days. The FSDO will forward the file to the Airmen Certification Branch, AFS-760.
(3) Do not issue Form 8060-4.
(4) When the applicant passes the computer knowledge tests, the applicant may present the computerized test report(s) along with an original of Form 8610-2 to the nearest FSDO or an appropriately rated DME. At that time, Form 8060-4 will be issued with the appropriate ratings. The applicant must complete and sign the “Applicant’s Certification” area. The “Applicant’s Certification” area and the “FAA Inspector’s Report” area are the only entries required. AFS-760 is aware of testing procedures for applicants under § 65.80. Give the applicant a machine copy of the original Form 8610-2 (for use in case the certification file is lost).
(5) The typed original Form 8060-4, the computerized test report(s), and the original of Form 8610-2 will be forwarded to the supervising FSDO within 5 calendar days after completion of the file.
e. Assignment of Seal Symbol—DPRE Only. At the time of initial certification, each parachute rigger is assigned an identification seal symbol. The FSDO in need of a seal symbol will make a request to AFS-760, which will then send a list of seal symbols that can be assigned.
Note: FAA Form 3318, Parachute Rigger Seal Symbol Assignment Card, will be discontinued when the current supply is exhausted.
8. Applicants Under 18 Years of Age. An applicant who meets the requirements of part 65, except for part 65, § 65.71(a)(1) or § 65.113, may take the oral and practical tests. Inform, the applicant that if the tests are passed, the Temporary Certificate will not be issued until the applicant’s 18th birthday. For applicants under 18 years of age:
a. Do not issue Form 8060-4.
b. On the reverse side of Form 8610-2, under the “Remarks” area put the following statement: The applicant is under 18 years of age. Temporary certificate was not issued. (Refer to appendix D, Figure D-10, and appendix E, Figure E-5.)
c. Send one original of Form 8610-2 to the supervising FSDO or IFO.
d. Give the applicant one original (completed and signed) of Form 8610-2 and the computerized test report(s).
e. Instruct applicants that upon reaching 18 years of age, they may present their originals of Form 8610-2 and the computerized test reports(s), to the nearest FSDO or IFO or appropriately rated TPE, whereupon Form 8060-4 will be issued with appropriate ratings.
f. When the applicant reaches 18 years of age and presents the appropriate documents, the inspector or TPE must forward the typed original Form 8060-4; Form 8610-2 after the applicant signs the “Applicant’s Certification” area (this is the original that was returned to the applicant at the time certification testing was completed); and the computerized test report(s), to the supervising FSDO or IFO within 5 calendar days after completion of the file. The “Applicant’s Certification” area and the “FAA Inspector’s Report” area are the only entries allowed. AFS-760 is aware of testing procedures for applicants less than 18 years of age. The inspector or TPE must make a copy of the completed Form 8610-2 for the applicant’s records.
9. When the Applicant Fails. When the applicant has failed all or any part of the oral and practical tests:
a. Give a Completed and Signed Original of FAA Form 8610-2 to the Applicant. The form will serve as notification of the areas passed, failed, or not completed, and the form must be presented to a TPE for retest. Identify the Subject Area(s)/Section(s) or Task(s)/Area(s) of Operation failed and record them in the “Remarks” block on the reverse side of the Form 8610-2. Use these Subject Areas/Sections or Tasks/Areas of Operation for reference when receiving additional instruction and when Form 8610-2 is presented for a retest.
Note: For retest procedures see chapter 5, paragraphs 2d and 2e.
b. Return to the Applicant:
(1) The computerized test report(s).
(2) Form 8610-2 (original) from all previously failed oral and practical tests.
c. Send the certification file to the supervising FSDO or IFO.
Note: Do not hold the file until retesting.
10. Disposition of Files. TPEs must carefully check Form 8610-2 to ensure that all entries have been properly made. Have the applicant sign his or her copy of Form 8060-4. Check the complete certification file before the applicant departs from the testing area.
a. Attachments. Check the boxes for each required attachment on the reverse side of Form 8610-2. Record the number of documents in parenthesis following the attachment’s name. (Refer to appendix D, Figures D-6 through D-11, and appendix E, Figures E-3 through E-6.) The FAA cannot issue a permanent airman certificate unless all required documents are completed and on file. AFS-760 will return files without supporting information or required documents.
b. Files. Files must be forwarded to the supervising FSDO or IFO within 5 calendar days. The supervising FSDO or IFO will forward the files to:
Airmen Certification Branch, AFS-760 P.O. Box 25082, Oklahoma City, OK 73125-4940
c. Retain Copy. The TPE is encouraged to keep a copy of Form 8610-2 for a record of oral and practical tests administered.
d. Applicant Passes. If the applicant passes, the TPE must provide the following:
(1) To the supervising FSDO or IFO:
(a) One original Form 8610-2.
(b) Computerized test report(s).
(c) Form 8060-4 (typed original).
(d) AC Form 8060-1 superseded if test is for added rating.
(e) If retest, statement complying with part 65, § 65.19(b), if retest is within 30 days of previous test.
(f) Test planning sheet.
(g) If applicable, any attachments (e.g., a statement of additional instruction, directions to the applicants place of residence, or any of attachments required by chapter 5, paragraph 6).
(2) To the applicant:
(a) Form 8060-4 (duplicate) if the supervising FSDO or IFO has authorized the DME to issue Form 8060-4.
(b) Original Form 8610-2 (second copy).
e. Applicant Fails. If the applicant fails, the TPE must provide the following:
(1) To the supervising FSDO or IFO:
(a) One original Form 8610-2.
(b) If retest, statement complying with § 65.19(b), if retest is within 30 days of previous test.
(c) Test planning sheet.
(2) To the applicant:
(a) One original Form 8610-2.
(b) Computerized test report(s).
(c) If retest, Form 8610-2 (original) from previously failed test(s).
f. Files. Refer to the appropriate paragraphs of this order for handling of files for applicants who are under 18 years of age (chapter 5, paragraph 8) or who take the oral and practical tests before the computer knowledge tests under the provisions of § 65.80 (chapter 5, paragraph 6).
11. Issuance of FAA Form 8060-4 by a TPE When Oral and Practical Tests are Not Administered.
a. New FAA Form 8610-2. A new Form 8610-2 is not required in the following instances:
(1) The applicant was under 18 years of age when the required tests were passed. (Refer to § 65.71(a)(1) or § 65.113.)
(2) The applicant passed the oral and practical tests before taking the computer knowledge tests. (See § 65.80.)
b. Determine the Required Tests Were Passed. When an applicant requests an airman certificate based on passing the tests under any of the conditions listed in chapter 5, paragraph 10a, carefully determine that the required tests were passed during a 24-calendar-month period. (See part 65, § 65.71(a)(3).)
c. Complete Reverse Side of FAA Form 8610-2. Require the applicant to complete the “Applicant’s Certification” area on the reverse side of Form 8610-2 following the “Designated Examiner’s Report.” The “Applicant’s Certification” area is used to verify that the applicant still meets the conditions and requirements of §§ 65.11 and 65.12.
d. Entries Above the Examiner’s Signature on FAA Form 8610-2. The inspector or TPE issuing Form 8060-4 and submitting the file must not make any entries above the examiner’s signature on the reverse side of Form 8610-2 (with the exception of the “Remarks” area). At this time, make the applicant a machine copy (for use in case the certification file is lost).
e. Applicant Meets 14 CFR part 65, § 65.71 or § 65.113. If the applicant meets part 65, § 65.71 or § 65.113 for the certificate requested, the TPE must provide the following:
(1) To the supervising FSDO or IFO:
(a) Form 8610-2.
(b) Computerized test report(s).
(c) Form 8060-4 (typed original).
(2) To the applicant:
(a) Form 8060-4 (duplicate).
(b) A machine copy of the original Form 8610-2 (for use in case the certification file is lost).
12. Reconstruction of a Lost Certification File.
a. Copy of FAA Form 8610-2 and FAA Form 8060-4. Copies of signed original Forms 8610-2 and 8060-4 are required. If no copy exists, the information that appeared on the original application must be provided on a new Form 8610-2 and Form 8060-4 complete with signatures (applicant, examiner, and inspector).
b. Duplicate Reports. AFS-760 will furnish the duplicate test report(s) provided they be furnished with the approximate date(s) and location(s) of the computer knowledge test(s).
c. Reconstructed File. In the upper right hand block of Form 8610-2 the wording “Reconstructed File” must appear in red ink.
d. Forward Certification File. Forward all information regarding the certification file through the FSDO or IFO to: FAA, Attn: Airmen Certification Branch, AFS-760, P.O. Box 25082, Oklahoma City, OK 73125-4940.
Chapter 6. Termination
Chapter 6. Termination
1. Termination. Termination is the action by the FAA to either not renew or rescind a TPE’s designation at any time for any reason the Administrator considers appropriate. Termination of a TPE’s designation for reasons other than insufficient need for the TPE’s services or the inability of the FSDO or IFO to manage the TPE will begin when other means of ensuring the TPE’s conformance to standards are unsuccessful, unfeasible, or inappropriate.
2. Reasons for Termination. The Administrator terminates a designation for any of the following reasons:
a. For any appropriate reason.
b. Upon the written request of the TPE.
c. When there is no longer a need for the TPE’s services or the FSDO or IFO no longer has the ability to manage the TPE.
d. When the TPE does not successfully complete the TPE Recurrent Seminar.
e. Upon the Administrator finding that the TPE has not properly performed TPE duties.
3. Examples of Deficiencies. The following are examples of deficiencies in a TPE’s performance of duties:
a. Unsatisfactory performance in any phase of duties or responsibilities, including the inability to accept or carry out the supervising FSDO’s or IFO’s instructions.
b. Any action that may discredit the FAA (e.g., misuse of the designation, or failure to maintain a reputation for integrity and dependability in the industry and the community).
c. The inability to work harmoniously with FSDO or IFO personnel or the public.
d. Evidence that the TPE’s general and/or professional qualifications and requirements were not met at the time of the original designation or at any time thereafter.
e. Inability to demonstrate satisfactory performance during a knowledge and skill evaluation or during an Initial TPE Seminar or a Recurrent TPE Seminar.
f. Failure to maintain or inability to demonstrate, qualifications for any certificate, rating, or TPE designation held.
4. Documentation. The FSDO or IFO will document deficiencies in a TPE’s performance. The FSDO or IFO will notify the TPE in writing of the deficiencies and give the TPE an opportunity to correct them within 90 days. The notification will also explain that the TPE privileges are under immediate suspension until further notice. The FSDO or IFO should advise the TPE that continued poor performance constitutes grounds for termination of the TPE’s designation.
5. Proposed Termination. The FSDO or IFO will provide the TPE with written notice and an opportunity to respond to a proposed action to terminate a designation. Designations are terminated under the general conditions contained in 14 CFR part 183, § 183.15(c).
6. Notification. The FSDO or IFO will notify the designee in writing of the reasons for the proposed action. The reason(s) cited will be as specific as possible. The notification will cite any applicable rule and/or handbook guidance. When the reasons are supported by examples of unacceptable conduct, examples will be stated. The reasons cited may be supported by documented surveillance or the results of other investigations; however, supporting documents will not be included with the notification to the TPE. The notification will explain that the TPE privileges are under immediate suspension.
7. Option to Respond. The written notification will give the designee the option to respond in writing or in person. The designee may elect to bring counsel if responding in person. The FAA will make a record of any meeting held. The supervising FSDO or IFO will send a copy of the record to the TPE. The TPE may submit comments or propose corrections to the record.
8. FSDO or IFO Manager’s Decision. The TPE will receive in writing the FSDO or IFO manager’s decision regarding the termination of a designation.
a. If the manager’s decision is against termination, the written notification to the TPE will indicate such and state that the TPE’s privileges are no longer suspended. If the manager’s decision is for renewal, the written notification to the TPE will indicate that his or her privileges are no longer suspended, and the FSDO or IFO will follow the renewal procedures discussed in this order. (Refer to chapter 3, paragraph 5.)
b. If the manager’s decision is for termination, the written notification to the TPE should indicate the reasons.
9. Appeal. The TPE may request the regional appeal panel review the matter. Termination due to insufficient need for the TPE’s services or the inability of the FSDO or IFO to manage the TPE cannot be appealed.
a. If the TPE wishes to appeal to the regional panel, the TPE must make the request in writing within 14 days of receiving the written notification of the FSDO or IFO manager’s decision.
b. The TPE will be notified in writing of the appeal panel’s decision and the reasons for that decision. The notification must be made within 15 days of the decision. Should the appeal panel reverse the decision of the FSDO or IFO manager, the written notification process outlined in this order must be followed. (Refer to chapter 6, paragraph 8a.)
Note: The regional appeal panel’s decision is final.
10. Voluntary Surrender. A TPE may voluntarily surrender a designation at any time. This voluntary surrender should be made in writing and be accompanied by the TPE’s FAA Form 8430-9, Certificate of Authority.
Chapter 7. Administrative Information
Chapter 7. Administrative Information
1. Distribution. Distribute this order to the division level in the Flight Standards Service and regional Flight Standards Divisions; to all FSDOs and IFOs; and to all TPEs.
2. Deviations. It is necessary to adhere to procedures in this order to achieve uniform administration of this directive material. Any deviations from this guidance material must be coordinated and approved by the Aircraft Maintenance Division, AFS-300, in coordination with the Designee Standardization Branch, AFS-640. If a deviation becomes necessary, the FAA inspector involved should ensure the deviations are substantiated, documented, and concurred with by the appropriate supervisor before forwarding to AFS-300. Submit a copy of the deviation to AFS-640 for review and concurrence.
3. Suggestions or Comments. AFS-640 welcomes and considers all your suggestions or comments regarding this order.
a. Use FAA Form 1320-19, Directive Feedback Information. For your convenience, Form 1320-19 is on the last page. Please use the “Other Comments” block on FAA Form 1320-19 to provide a complete explanation of why the suggested change is necessary. You may correct, as necessary, a copy of the pertinent information, or provide a handwritten note for consideration.
b. Contact AFS-640. You may address your suggestions or comments to FAA, Attn: Designee Standardization Branch, AFS-640, P.O. Box 25082, Oklahoma City, OK 73125. If an interpretation is urgently needed call AFS-640 for guidance at (405) 954-4220. Please use the attached FAA Form 1320-19 as a followup to any verbal conversation.
7/14/08 8610.12 Appendix A
Appendix A. Instructions for Completing FAA Form 8610-2, Airman Certificate
Appendix A. Instructions for Completing FAA Form 8610-2, Airman Certificate
and/or Rating Application
1. Procedures for Completing FAA Form 8610-2. This appendix explains the procedures to be followed when applicants, TPEs, and inspectors complete Form 8610-2.
a. Form 8610-2. The TPE or inspector must provide Form 8610-2 to the applicant.
b. Two Originals. The applicant must complete two originals of Form 8610-2 before testing begins.
c. Detailed Instructions. The TPE or inspector must give detailed instruction(s) for correctly completing Form 8610-2.
Note: The inspector or TPE must copy appendix A and provide it to the applicant until Form 8610-2 is revised with written instructions attached.
d. Use Permanent Dark Ink or Use a Typewriter. All entries on Form 8610-2 must be made with permanent dark ink or typewritten.
Note: When you make a correction, cross out, and initial the mistake. Do not use correction fluid (e.g., white out) or correction tape.
e. Signatures. All signatures must be original, in dark ink, with the name printed in dark ink or typewritten below or beside the signature.
f. Eight-Digit Numeric Characters. Enter all dates using eight-digit numeric characters (e.g., 05/05/2002). (Month, Day, Year.) (Do not enter dates as May 5, 2002 or 05/05/02.)
Figure A-1. Privacy Act.
7/14/08 8610.12 Appendix A
2. Privacy Act. The TPE or inspector must advise the applicant to read the “Privacy Act” on Form 8610-2. Remove the Privacy Act before using Form 8610-2. (See Figure A-1.)
Figure A-2. Top Section.
3. Complete the Top Section. The applicant must complete the top section of Form 8610-2.
a. “Mechanic” and “Parachute Rigger” Boxes. The applicant must check the appropriate box.
b. Ratings Box(es). The applicant must check the appropriate box(es) for the rating(s) sought (e.g., Airframe and/or Powerplant; Senior or Master; Seat, Back, Chest, and/or Lap).
c. Check Original Issuance or Added Rating Box. The applicant must check either the “ORIGINAL ISSUANCE” or the “ADDED RATING” box. The “ADDED RATING” box will only be checked when the applicant has an airman certificate and is actually adding a rating to that certificate.
Note: Line through the rating(s) not applied for unless, the applicant currently holds the rating. (Refer to appendix D, Figure D-1, and appendix E, Figure E-1.)
Figure A-3. Block I—Applicant Information.
4. Block I—Applicant Information. The TPE or inspector must warn the applicant to read the fine print.
7/14/08 8610.12 Appendix A
a. Item A—Name (First, Middle, Last)
(1) The applicant must enter his or her legal name; however, for records purposes, no more than one middle name can be entered. The applicant’s name must not be changed on the subsequent Form 8610-2 unless it is done in accordance with part 65, § 65.16. If the applicant’s name exceeds the number of characters allowed (50, including spaces), the Airmen Certification Branch, AFS-760, will make necessary changes to allow for computer acceptance.
(2) If the applicant has no middle name, the applicant must enter “NMI” (no middle initial) or “NMN” (no middle name).
(3) If the applicant has initial(s) only, the applicant must enter those initials and then enter “Initial Only.”
(4) The applicant will indicate if he or she is a junior, III, IV, etc.
Note: If the applicant already has an FAA airman certificate, the name on Form 8610-2 must be the same as the name on the FAA airman certificate unless it is changed in accordance with § 65.16.
b. Item B—Social Security Number.
(1) Disclosure of the SSN is optional (Refer to “Privacy Act”). However, item B cannot be left blank.
(2) The applicant must either enter his or her SSN or enter one of the following notations: “Do Not Use.” or “None.”
c. Item C—D.O.B. (Mo., Day, Yr.).
(1) The applicant must enter all dates using eight-digit numeric characters (e.g., 07/09/1965). (Month, Day, Year.) (Do not enter the dates as July 9, 1965 or 07/09/65.)
(2) The TPE or inspector must verify the date of birth (D.O.B.). The D.O.B is a problem area.
(3) If the applicant has other FAA certificate(s), the TPE or inspector must verify that the “D.O.B.” is the same as that entered on the Form 8610-2.
d. Item D—Height.
(1) The applicant must enter his or her height in inches (e.g., If the applicant is 5’ 9,” the he or she would enter “69”).
(2) The applicant will use whole inches only, no fractions.
e. Item E—Weight.
(1) The applicant must enter his or her weight in pounds.
7/14/08 8610.12 Appendix A
(2) The applicant will use whole pounds only, no fractions.
f. Item F—Hair.
(1) The applicant must spell out the color of his or her hair or use an abbreviation that cannot be confused with another color.
(2) Acceptable hair colors are brown, black, blonde, gray, and red.
(3) If the applicant is bald, enter “Bald.”
(4) If the applicant is wearing a wig or toupee, enter the color of hair under the wig or toupee.
g. Item G—Eyes.
(1) The applicant must spell out the color of his or her eyes or use an abbreviation that cannot be confused with another color.
(2) Acceptable eye colors are brown, black, blue, hazel, gray, and green.
h. Item H—Sex.
(1) If the applicant is a male, he will enter “M.”
(2) If the applicant is a female, she will enter “F.”
i. Item I—Nationality (Citizenship).
(1) The applicant must enter the country in which he or she maintains citizenship.
(2) The applicant’s nationality must be one listed in appendix C.
(3) Dual citizenship will be accepted. Because of limited space on the permanent certificate, only show one citizenship reference under “Nationality.” Annotate dual citizenship in the “Remarks” area. (Example: Citizenship: U.S./Canada.) The other will be shown as a limitation on the certificate (e.g., Dual citizenship includes Canada).
(4) Stateless is acceptable, if appropriate.
j. Item J—Place Of Birth.
(1) If the applicant was born in the U.S., the applicant must enter the city and state.
(2) If the city is unknown, enter the county and state.
(3) If the applicant was born outside of the U.S., the applicant must enter the name of the city and country, or province and country. If the applicant was not born in a city and country or a
7/14/08 8610.12 Appendix A
province and country, (e.g., Middle of Atlantic Ocean on the HMS Queen Victoria), that information must be entered in the “Remarks” area.
k. Item K—Permanent Mailing Address.
(1) “Number and Street, P.O. Box, Etc.” The applicant must enter this information above the first dotted line. This information must not exceed 33 characters, including spaces.
(2) “City.” The applicant must enter this information above the second dotted line. The city name must not exceed 17 characters, including spaces. When necessary, the applicant must abbreviate the address (not to exceed 17 characters, including spaces).
(3) “State.” The applicant must enter this information above the third dotted line.
(4) “Zip Code.” The applicant must enter this information above the third dotted line.
Note: These directions are not required for APO/FPO type addresses. A post office address is not acceptable for the purpose of applying for an airman certificate unless the applicant resides on a rural route, a boat, or in some other manner that requires the use of a post office box or rural route for an address. This also includes business addresses, flight school addresses, a personal mail box, commercial addresses, or other mail drops. The airman may use these addresses as his or her preferred mailing address; however, the applicant must also include his or her residence address, map, or written directions to the physical address. If a post office box or rural route is used, the applicant must furnish (on a separate sheet of paper) the directions required to find his or her residence. The applicant must sign as this becomes part of the certification file. Example: I live 2 miles north of State Highway 12 on Mockingbird Lane in a two-story house with a barn in the back.” (The applicant must sign this statement.) Two copies are required.
l. Item L—Have You Ever Had An Airman Certificate Suspended Or Revoked?
(1) The applicant must check either the “Yes” box or the “No” box. (A student pilot certificate is a pilot certificate.)
(2) If the “Yes” box is checked, refer to §§ 65.11(c), 65.11(d)(2), and 65.12.
(3) If the TPE or applicant does not understand the requirements of part 65 as it applies to a particular situation, contact the supervising FSDO or IFO for clarification and assistance.
m. Item M—Do You Now Or Have You Ever Held An FAA Airman Certificate?
(1) The applicant must check either the “Yes” box or the “No” box.
(2) If the applicant checks the “Yes” box, the applicant must make an entry by the “Specify Type” area.
7/14/08 8610.12 Appendix A
(3) The types of certificates that must be entered in the “Specify Type” area are: pilot, mechanic, repairman, etc. (A student pilot certificate is a pilot certificate.)
Note: An Inspection Authorization, DME, DPRE, etc., are not FAA certificates.
n. Item N—Have You Ever Been Convicted For Violation Of Any Federal Or State Statutes Pertaining To Narcotic Drugs, Marijuana, And Depressant Or Stimulant Drugs Or Substances?
(1) The applicant must check either the “Yes” box or the “No” box.
(2) If the applicant checks the “Yes” box, the applicant must make an entry by the “Date of Final Conviction” area. (Refer to § 65.12.)
(3) If the DME or applicant does not understand the requirements of part 65 as it applies to a particular situation, contact the supervising FSDO or IFO for clarification and assistance.
Figure A-4. Block II—Certificate or Rating Applied for On Basis of—
5. Block II—Certificate or Rating Applied for On Basis of—(Refer to appendix D, Figures D-1 through D-5, and appendix E, Figures E-1 and E-2.)
a. Graduate of AMTS. When the applicant is a graduate of an approved Aviation Maintenance Technician School (AMTS), the applicant must complete block II as follows:
(1) Item D—Graduate of Approved Course. The applicant will check item D, if he or she is a graduate of an AMTS.
Continue reading ↓ 120 of 181 passages shown