Radar Vectors
FAA Order Cancelled Issued Mar 10, 2009 AFS-420 223 pages Copy saved Nov 18, 2026

Order 8260.42B United States Standard for Helicopter Area Navigation (RNAV)

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

Document Label: CHANGE

ORDER U.S. DEPARTMENT OF TRANSPORTATION

8260.42B CHG 2 FEDERAL AVIATION ADMINISTRATION

Effective Date: National Policy 05/22/2020

SUBJ: United States Standard for Helicopter Area Navigation (RNAV)

1. Purpose. This change incorporates updated office identifications to reflect the current FAA organizational structure; while removing routing symbols/codes. Also, this change ensures all users have the most up-to-date information to reduce confusion with functional FAA structures. This order contains guidance that is pertinent to 14 CFR Part 97.

2. Who this change affects. This is an administrative editorial change only.

3. Where You Can Find This Change. You can find this change on the Directives Management System (DMS) Website: http://www.faa.gov/regulations_policies/orders_notices.

4. Explanation of Changes.

a. General. Throughout the document, updated office identifications to reflect the current FAA organizational structure; replaced with the appropriate organization title. Removed outdated/obsolete references.

b. Table of Contents. Updated reflecting the correct content.

c. Appendix B. Removed, the content from this appendix is now addressed in Order 8260.3, United States Standard for Terminal Instrument Procedures (TERPS).

d. Appendix C. Renamed to Appendix B.

Distribution: Electronic Distribution Initiated By: AFS-400

PAGE CHANGE CONTROL CHART

Remove Pages Dated Insert Pages Dated

CHG 1 (Cover pg. 1 and 2) 11/20/2012 CHG 1 (Cover pg. 1 and 2) 05/22/2020 iii (and iv) 11/20/2012 iii (and iv) 05/22/2020 1-1 (and 1-2) 11/20/2012 1-1 (and 1-2) 05/22/2020 2-5 and 2-6 03/10/2009 2-5 and 2-6 05/22/2020 8-11 and 8-12 11/20/2012 8-11 and 8-12 05/22/2020 A-1 and A-2 03/10/2009 A-1 and A-2 05/22/2020 B-1 through B-148 03/10/2009 B-1 through B-6 05/22/2020 C-1 and C-6 11/20/2012

5. Distribution. This change is distributed electronically only. This document was signed by Robert C. Carty, Deputy Director of Flight Standards Service.Rick Domingo Executive Director, Flight Standards Service

Document Label: CHANGE 8260.42B FEDERAL AVIATION ADMINISTRATION U.S. DEPARTMENT OF TRANSPORTATION

CHG 1

Effective Date: National Policy 11/20/2012

SUBJ: United States Standard for Helicopter Area Navigation (RNAV)

1. Purpose. This change incorporates new Helicopter Departure and Localizer Precision with Vertical (HLPV) criteria. Order 8260.42B contains criteria for the formulation, review, approval, and publication of area navigation (RNAV) helicopter instrument procedures based on Global Positioning System (GPS) and Wide Area Augmentation System (WAAS) navigation.

2. Audience. The primary audience for this Order is the Air Traffic Organization (ATO), Mission Support Services (MSS), Aeronautical Information Services, who has the responsibility to develop instrument flight procedures. The secondary audience includes the ATO Service Areas' Operational Support Group, Flight Procedures Team (OSG-FPT), ATO Flight Program Operations, and Flight Standards offices.

3. Where You Can Find This Change. You can find this order on the Directives Management System (DMS) Website: http://www.faa.gov/regulations_policies/orders_notices.

4. Explanation of Changes. Significant areas of new direction, guidance, policy, and criteria as follows:

Note: General. All references to FAA Orders 8260.52, United States Standard for Required Navigation Performance (RNP) Approach Procedures with Special Aircraft and Aircrew Authorization Required (SAAAR), and 8260.54A, The United States Standard for Area Navigation, are now found in FAA Order 8260.58, United States Standard for Performance Based Navigation (PBN) Instrument Procedure Design.

a. Table of Contents. Updated Table of Contents to coincide with the pages changed.

b. Chapter 1. Added further explanation regarding “automation” to include the use of the calculators embedded in this order and the geodetic calculator available on the Flight Procedures and Airspace Group (FPAG) web site, or CompSys 21 geodetic calculator available on the Aeronautical Information Services' web site, or Instrument Approach Procedure Automation/Instrument Procedures Development System (IAPA/IPDS), or other FPAG-approved geodetic calculator.

c. Chapter 2.

Distribution: Electronic Only Initiated By: AFS-400

(1) Paragraph 2. Added use of “rounding.”

(2) Paragraph 2b. Updated Mathematics Convention to include feet per nautical mile (fpnm).

d. Chapter 6. Added Helicopter Departure criteria. This chapter describes RNAV departure criteria describing a visual departure from a non-instrument flight rules (IFR) departure location to an Initial Departure Fix to join with the IFR portion of the departure. This includes both public and special departure criteria.

e. Chapter 8. Added Helicopter Localizer Precision with Vertical (HLPV) criteria. This chapter describes the development of the HLPV Approach to a Point in Space and the initial missed approach segment.

f. Appendix C. Added new definitions to support new criteria in chapters 6 and 8.

Original Signed by

John M. Allen Director, Flight Standards Service

PAGE CONTROL CHART

Remove Pages Dated

i thru ii 03/10/09

1-1 thru 1-2 03/10/09

2-1 thru 2-4 03/10/09

NEW N/A

NEW N/A

C-1 thru C-6 03/10/09

Insert Pages Dated

i thru iv 11/20/12

1-1 thru 1-2 11/20/12

2-1 thru 2-4 11/20/12

6-1 thru 6-46 11/20/12

8-1 thru 8-22 11/20/12

C-1 thru C-6 11/20/12

Docume

nt Label: Order 8260.42B National Policy

Effective Date: March 10, 2009

SUBJ: United States Standard for Helicopter Area Navigation (RNAV)

These criteria are the Federal Aviation Administration (FAA) standards for developing helicopter area navigation (RNAV) instrument procedure construction based on Global Positioning System (GPS). This revision adds definitions, changes procedure identification from GPS to RNAV, provides specific holding pattern leg lengths, helicopter en route criteria, decreases navigation system error tolerance for along-track distance in the terminal area, and adds departure criteria, minimums, and requirements. The types of final approaches have been revised. They are Instrument Flight Rules (IFR) to an IFR heliport, IFR to a Visual Flight Rules (VFR) heliport (Proceed Visually), Point-in-Space (PinS) approach (Proceed VFR), and IFR to Runways with separate criteria for each.

The first step to increase helicopter IFR utility is the development of helicopter RNAV instrument procedures. Ongoing testing and criteria development by the FAA for application of the Wide Area Augmentation System (WAAS) will provide the next major step. WAAS with its increased integrity and 3-dimensional (3D) approach capability will allow narrower route widths and approaches with vertical guidance (APV).

Original Signed by

John H. Allen Director, Flight Standards Service

Distribution: A-W(AS/ND/AT/AF/FS)-3; A-X(FS/AF/AT/AS)-3; Initiated By: AFS-420 AJW-32 (200 Cys); AMA-200 (12 Cys); ZVS-827; Special Military and Public Addresses

Record of Changes - Table 8260.42B

CHANGE SUPPLEMENTS CHANGE SUPPLEMENTS

OPTIONAL USE TO

BASIC

OPTIONAL USE TO

BASIC

FAA Form 1320-5 SUPERSEDES PREVIOUS EDITION

Table of Contents

Page Chapter 1. General

1-1. Purpose ---------------------------------------------------------------------------- 1-1 1-2. Audience--------------------------------------------------------------------------- 1-1 1-3. Where Can I Find This Order?-------------------------------------------------- 1-1 1-4. What This Order Cancels-------------------------------------------------------- 1-1 1-5. Explanation of Policy Changes ------------------------------------------------- 1-1 1-6. Effective Date --------------------------------------------------------------------- 1-1

Chapter 2. General Criteria

2-1. General----------------------------------------------------------------------------- 2-1 2-2. Data Resolution ------------------------------------------------------------------- 2-2 2-3. Procedure Identification --------------------------------------------------------- 2-7 2-4. Segment Width (General) ------------------------------------------------------- 2-8 2-5. Calculating the Turn Radius (R)------------------------------------------------ 2-12 2-6. Turn Construction ---------------------------------------------------------------- 2-15 2-7. Helicopter Initial and Intermediate Descent Gradient ----------------------- 2-27 2-8. Feeder Segment ------------------------------------------------------------------- 2-27 2-9. Initial Segment -------------------------------------------------------------------- 2-31 2-10. Intermediate Segment ------------------------------------------------------------ 2-34 2-11. Determining Precise Final Approach Fix/Final Approach Fix ------------- 2-40 2-12. RESERVED----------------------------------------------------------------------- 2-41 2-16. Common Fix ---------------------------------------------------------------------- 2-41 2-17. Missed Approach Segment (MAS) Conventions----------------------------- 2-41

Chapter 3. Terminal Operations

3-1. Approach Configuration --------------------------------------------------------- 3-1

Chapter 4. IFR Final and Visual Segments

4-1. General----------------------------------------------------------------------------- 4-1 4-2. Missed Approach ----------------------------------------------------------------- 4-1 4-3. Procedure Types ------------------------------------------------------------------ 4-2 4-4. IFR Heliport Visual Segment --------------------------------------------------- 4-8 4-5. Special IFR Approach to a VFR Heliport (IVH) Proceed Visually-------- 4-15 4-6. Special IFR Approach to a VFR Runway (IVR) Proceed Visually -------- 4-18 4-7. PinS Approach (Proceed VFR) ------------------------------------------------- 4-19 4-8. IFR to an IFR Runway ----------------------------------------------------------- 4-20 4-9. WAAS LP Criteria --------------------------------------------------------------- 4-21

i

Table of Contents

Page Chapter 5. Missed Approach

1. General ---------------------------------------------------------------------------- 5-1 2. Straight Missed Approach ------------------------------------------------------- 5-4 3. Turning Missed Approach------------------------------------------------------- 5-5 4. Turning Missed Approach (Second Turn)------------------------------------- 5-17 5. Wind Spiral Cases ---------------------------------------------------------------- 5-20 6. Missed Approach Climb Gradient---------------------------------------------- 5-26

Chapter 6. Helicopter Instrument Departure Criteria

6-1. General----------------------------------------------------------------------------- 6-1 6-2. Terms------------------------------------------------------------------------------- 6-1 6-3 Obstacle Departure Procedures ------------------------------------------------- 6-1 6-4. PinS Departures------------------------------------------------------------------- 6-1 6-5. Obstacle Evaluation Area-------------------------------------------------------- 6-4 6-6. General Public PinS Departure Construction --------------------------------- 6-5 6-7. Special PinS Departure Construction ------------------------------------------ 6-22 6-8. Obstacle Evaluation (OE) ------------------------------------------------------- 6-36 6-9. Required Obstacle Clearance (ROC)------------------------------------------- 6-38 6-10. Obstacle Distance Measurement------------------------------------------------ 6-39 6-11. Visual Segment ------------------------------------------------------------------- 6-42 6-12 Weather Minimums -------------------------------------------------------------- 6-44

Chapter 7. Minimums for Helicopter Nonprecision RNAV and WAAS Approaches

7-1. Application ------------------------------------------------------------------------ 7-1

Chapter 8. HLPV PinS Final Approach Segment (FAS) Evaluation

8-1. General----------------------------------------------------------------------------- 8-1 8-2. Final Segment Obstruction Evaluation Area (OEA) ------------------------- 8-3 8-3. W OCS----------------------------------------------------------------------------- 8-5 8-4. X OCS------------------------------------------------------------------------------ 8-7 8-5. Y OCS------------------------------------------------------------------------------ 8-8 8-6. HAS and DA ---------------------------------------------------------------------- 8-9 8-7. Revising Glide Path Angle for OCS Penetrations---------------------------- 8-10 8-8. Adjusting TCH to Reduce/Eliminate OCS Penetrations -------------------- 8-12 8-9. Missed Approach Section 1 ----------------------------------------------------- 8-12 8-10. Surface Height Evaluation------------------------------------------------------- 8-19 8-11. Final Approach Segment (FAS) Data Requirements ------------------------ 8-21

ii

Table of Contents

Page

Appendix A. Conditions and Assumptions for IFR to VFR Heliport (IVH) (Proceed Visually) Approach Procedures

1. FAA Form 7480-1, Notice of Landing Area Proposal----------------------- A-1 2. No Penetration of the 8:1 Surface ---------------------------------------------- A-1 3. Acceptable Onsite Evaluation of the Heliport for VFR Use ---------------- A-1 4. Acceptable Evaluation of the Visual Segment for Flyability --------------- A-2 5. IFR Approach to a VFR Heliport (IVH) Analysis --------------------------- A-2

Appendix B. Administrative Information

1. Distribution-------------------------------------------------------------------------- B-1 2. Background-------------------------------------------------------------------------- B-1 3. Definitions--------------------------------------------------------------------------- B-1 4. Data Resolution --------------------------------------------------------------------- B-5 5. Related Publications---------------------------------------------------------------- B-5 6. Information Update----------------------------------------------------------------- B-5

iii (and iv)

THIS PAGE INTENTIONALLY LEFT BLANK

Chapter 1. General Information

1. Purpose of This Order. This order contains criteria for the formulation, review, approval, and publication of area navigation (RNAV) helicopter instrument procedures based on Global Positioning System (GPS) and Wide Area Augmentation System (WAAS) navigation.

2. Audience. This order is distributed in Airport Safety, Standards and Communications, and Navigation and Surveillance Systems; Air Traffic Organization; Flight Standards Services offices, and Airports Divisions; special mailing list ZVS-827, and Special Military and Public Addressees.

3. Where Can I Find This Order? This information is also available on the FAA's Web site at http://www.faa.gov/regulations_policies/orders_notices

4. What This Order Cancels. Order 8260.42A, Helicopter Global Positioning System (GPS) Nonprecision Approach Criteria.

5. Explanation of Policy Changes. This document has been completely revised for harmonization with FAA Order 8260.54, The United States Standard for Area Navigation (RNAV), incorporation of criteria policy documents, and to meet FAA Order 1320.1, FAA Directives Management, formatting requirements. These criteria were written for automated implementation through the use of the calculators embedded in the document, Flight Procedures and Airspace Group (FPAG) geodetic calculator, Compsys 21 geodetic calculator, Instrument Approach Procedure Automation/Instrument Procedures Development System (IAPA/IPDS), or other FPAG-approved geodetic calculation products. Formulas are presented in Math notation and standard text to facilitate programming efforts. Calculation examples were eliminated. Instead, an Adobe Acrobat version of the criteria document is available where each formula performs the calculation as an embedded calculator.

1-1 (and 1-2)

THIS PAGE INTENTIONALLY LEFT BLANK

Chapter 2. General Criteria

Section 1. Basic Criteria Information

2-1. General. These criteria assume use of Global Positioning System (GPS) or Wide Area Augmentation System (WAAS) receivers approved for approach operations, in accordance with Advisory Circular (AC) 20-138, Airworthiness Approval of Global Navigation Satellite System (GNSS) Equipment; Technical Standard Order (TSO) C-129 Class A (1) systems; and AC 20-130, Airworthiness Approval of Navigation or Flight Management Systems Integrating Multiple Navigation Sensors, for GPS as part of a multi-sensor system meeting TSO-C129 Class C (1) System or pertinent military guidance. Advisory Circular (AC) 20-138C, Airworthiness Approval of Positioning and Navigation Systems, and Technical Standard Order (TSO) C196A, Airborne Supplemental Navigation Sensors for Global Positioning System Equipment using Aircraft-Based Augmentation, contain updated Airworthiness guidance. WAAS navigation equipment must be approved in accordance with the requirements specified in TSO-C145, Airborne Navigation Sensors Using the Global Positioning System (GPS) Augmented by the Wide Area Augmentation System (WAAS), or TSO-C146, Stand-Alone Airborne Navigation Equipment Using the Global Positioning System (GPS) Augmented by the Wide Area Augmentation System (WAAS).

Unless otherwise specified, Order 8260.3, United States Standard for Terminal Instrument Procedures (TERPS), applies. For public use procedures, the heliport must meet the guidance contained in AC 150/5390-2, Heliport Design. Obstacle clearance area dimensions are based on 90 knots indicated airspeed (KIAS) maximum in the initial and intermediate segments and 70 KIAS maximum in the final and missed approach segments until passing the missed approach holding fix. USA/USAF/USN/USCG only: procedures are designed for 90 KIAS in the final and missed approach segments.

The following FAA orders apply:

 7130.3, Holding Pattern Criteria.

 8260.3, United States Standard for Terminal Instrument Procedures (TERPS).

 8260.19, Flight Procedures and Airspace.

Apply chapter 2, section 3 of Order 7130.3, Holding Pattern Criteria. Use pattern 4 for all helicopter holding (including climb-in-hold) up to and including 10,000 ft. Chart 4 nautical mile (NM) leg lengths.

The feeder, initial, intermediate, final, and missed approach criteria described in this order supersede the other publications listed above. See Order 8260.3, Volume 1, chapter 3 to determine visibility minima.

Formulas are numbered by chapter and depicted in standard mathematical notation and in standard text to aid in computer programming. Each formula contains a java script functional calculator.

Formula X-X. Formula Title

X2 Y  Formula in   math notation tan 3     180  where X = variable value

The calculated answer is

printed after the grey

button is clicked

Formula Example

2-2. Data Resolution. Perform calculations using an accuracy of at least 15 significant digits; i.e., floating point numbers must be stored using at least 64 bits. Unless otherwise noted, do not round intermediate results. Round only the final result of calculations for documentation purposes. Required accuracy tolerance is 1 centimeter for distance and 0.002 arc-second for angles. The following list specifies the minimum accuracy standard for documenting data expressed numerically. This standard applies to the documentation of final results only; e.g., a calculated adjusted glidepath angle of 3.04178 degrees is documented as 3.05 degrees. The standard does not apply to the use of variable values during calculation. Use the most accurate data available for variable values.

a. Documentation Accuracy:

(1) WGS-84 latitudes and longitudes to the nearest one hundredth (0.01) arc second; [nearest five ten thousandth (0.0005) arc second for Final Approach Segment (FAS) data block entries];

(2) Flight Path Alignment Point (FPAP) mean sea level (MSL) elevation to the nearest foot;

(3) FPAP height above ellipsoid (HAE) to the nearest tenth (0.1) meter;

(4) Glidepath angle to the next higher one hundredth (0.01) degree;

(5) Courses to the nearest one hundredth (0.01) degree;

(6) Course width at threshold to the nearest quarter (0.25) meter; and

(7) Distances to the nearest hundredth (0.01) unit [except for “length of offset” entry in FAS data block which is to the nearest 8 meter value].

b. Mathematics Convention. Formulas in this document as depicted are written for radian calculation.

Note: The value for 1 NM was previously defined as 6,076.11548 ft. For the purposes of RNAV criteria, 1 NM is defined as the result of the following calculation:

1852 fpnm  0.3048

(1) Conversions:

 Degree measure to radian measure:

 radians  degrees 180

 Radian measure to degree measure:

180 degrees  radians 

 Feet to meters:

meters  feet . 0 3048

 Meters to feet:

meters feet  . 0 3048

 Feet to Nautical Miles (NM):

. 0 3048 NM  feet 1852

 NM to feet:

1852 feet  NM . 0 3048

 NM to meters:

meters  NM 1852

 Meters to NM:

meters NM  1852

 Temperature Celsius to Fahrenheit:

. TFahrenheit  1 8TCelcius  32

 Temperature Fahrenheit to Celsius:

T 32 Fahrenheit TCelcius  . 1 8

(2) Definition of Mathematical Functions and Constants:

a+b indicates addition a-b indicates subtraction ab or ab or a*b or ab indicates multiplication

a or a or ab indicates division b b

(a-b) indicates the result of the process within the parenthesis a-b indicates absolute value  indicates approximate equality a or a0.5 or a^0.5 indicates the square root of quantity “a” a2 or a^2 indicates aa In(a) or log(a) indicates the natural logarithm of “a” tan(a) indicates the tangent of “a” degrees tan-1(a) or atan(a) indicates the arc tangent of “a” sin(a) indicates the sine of “a” degrees sin-1(a) or asin(a) indicates the arc sine of “a” cos(a) indicates the cosine of “a” degrees cos-1(a) or acos(a) indicates the arc cosine of “a”

e The constant e is the base of the natural logarithm and is sometimes known as Napier’s constant, although its symbol (e) honors Euler. With the possible exception of , e is the most important constant in mathematics since it appears in myriad mathematical contexts involving limits and derivatives. Its value is approximately 2.718281828459045235360287471352662497757... r The TERPS constant for the mean radius of the earth for spherical calculations in feet. r = 20890537

(3) Operation Precedence (Order of Operations):

First: Grouping Symbols: parentheses, brackets, braces, fraction bars, etc. Second: Functions: Tangent, sine, cosine, arcsine, and other defined functions Third: Exponentiations: Powers and roots Fourth: Multiplication and Division: Products and quotients Fifth: Addition and subtraction: Sums and differences e.g., 5 − 3 • 2 = !1 because multiplication takes precedence over subtraction (5 - 3) 2 = 4 because parentheses take precedence over multiplication

62  12

because exponentiation takes precedence over division

5 because the square root sign is a grouping symbol

 7 because roots take precedence over addition

  9 16

 9 16

3

sin (30 °) = 1 because functions take precedence over division 0.5

⎛ 30 °⎞ sin ⎜ ⎟= 08660254 because parentheses take precedence over functions . ⎝ 05 . ⎠

Notes on calculator usage:

1. Most calculators are programmed with these rules of precedence.

2. When possible, let the calculator maintain all of the available digits of a number in memory rather than re-entering a rounded number. For highest accuracy from a calculator, any rounding that is necessary should be done at the latest opportunity.

c. Geospatial Standards. The following standards apply to the evaluation of obstacle and terrain position and elevation data relative to RNAV OEAs and OCSs. Terrain and obstacle data are reported in NAD-83 latitude, longitude, and elevation relative to MSL in National Geodetic Vertical Datum of 1929 (NGVD-29) or North American Vertical Datum of 1988 (NAVD-88) vertical datum. Evaluate obstacles using their NAD-83 horizontal position and NAVD-88 elevation value compared to the WGS-84 referenced course centerline (along-track and crosstrack), OEA boundaries, and OCS elevations as appropriate.

(1) WGS-84[G873] for Position and Course Construction. This reference frame is used by the FAA and the U.S. Department of Defense (DoD). It is defined by the National Geospatial-Intelligence Agency (NGA) (formerly the National Imagery and Mapping Agency, formerly the Defense Mapping Agency [DMA]). In 1986, the Office of National Geodetic Survey (NGS), redefined and readjusted the North American Datum of 1927 (NAD-27), creating the North American Datum of 1983 (NAD-83). The WGS-84 was defined by the DMA. Both NAD-83 and WGS-84 were originally defined (in words) to be geocentric and oriented as the Bureau International d I’Heure (BIH) Terrestrial System. In principle, the three-dimensional (3D) coordinates of a single physical point should be the same in both NAD-83 and WGS-84 Systems; in practice; however, small differences are sometimes found. The original intent was that both systems would use the Geodetic Reference System of 1980 (GRS-80) as a reference ellipsoid. As it happened, the WGS-84 ellipsoid differs very slightly from GRS-80. The difference is 0.0001 meters in the semi-minor axis. In January 2, 1994, the WGS-84 reference system was realigned to be compatible with the International Earth Rotation Service’s Terrestrial Reference Frame of 1992 (ITRF) and renamed WGS-84 (G730). The reference system underwent subsequent improvements in 1996, referenced as WGS-84 (G873) closely aligned with ITRF-94, to the current realization adopted by the NGA in 2001, referenced as WGS-84 (G1150) and considered equivalent systems to ITRF 2000.

(2) NAVD-88 for elevation values. NAVD-88 is the vertical control datum established in 1991 by the minimum-constraint adjustment of the Canadian-Mexican-U.S. leveling observations. It held fixed the height of the primary tidal bench mark, referenced to the new International Great Lakes Datum of 1985 local MSL height value, at Father Point/Rimouski, Quebec, Canada. Additional tidal bench mark elevations were not used due to the demonstrated variations in sea surface topography, (i.e., the fact that MSL is not the same equipotential surface at all tidal bench marks).

d. OEA Construction and Obstacle Evaluation Methodology.

(1) Courses, fixes, boundaries (lateral dimension). Construct straight-line courses as a WGS-84 ellipsoid geodesic path. If the course outbound from a fix differs from the course inbound to the fix (courses measured at the fix), then a turn is indicated. Construct parallel and trapezoidal boundary lines as a locus of points measured perpendicular to the geodesic path. (The resulting primary and/or secondary boundary lines do not display a “middle bulge” due to curvature of the ellipsoids surface since they are not geodesic paths.) NAD-83 latitude/longitude positions are acceptable for obstacle, terrain, and airport data evaluation. Determine obstacle lateral positions relative to course centerline/OEA boundaries using ellipsoidal calculations (see Order 8260.3).

(2) Elevations (vertical dimension). Evaluate obstacles, terrain, and airport data using their elevation relative to their orthometric height above the geoid (for our purposes, MSL) referenced to the NAVD-88 vertical datum. The elevations of OCSs are determined spherically relative to their origin MSL elevation (NAVD-88). Department of Defense (DoD) procedure developers may use EGM-96 vertical datum.

e. Evaluation of Actual and Assumed Obstacles (AAO). Apply the vertical and horizontal accuracy standards in Order 8260.19, paragraphs 272, 273, 274, and appendix 3. (USAF, apply guidance per AFI 11-230)

Note: When applying an assumed canopy height consistent with local area vegetation, contact the designated Flight Procedures Team (FPT) to verify the height value to use.

f. ATT Values. ATT is the value used (for segment construction purposes) to quantify position uncertainty of an RNAV fix. The application of ATT can; therefore, be considered “circular;” i.e., the ATT value assigned describes a radius around the plotted position of the RNAV fix (see figure 2-1 and table 2-1).

Figure 2-1. ATT.

Fix displacement

Note: Cross-track tolerance (XTT) values were considered in determining minimum segment widths, and are not considered further in segment construction.

GPS

WAAS*

(LP)

Table 2-1. ATT Values.

En Route Feeder, Initial, Intermediate, Missed Approach > 30 NM)

Terminal Feeder, Initial, Intermediate, Missed Approach ≤ 30 NM)

Approach

(final)

Approach

(final)

2.0 NM

1.0 NM

0.3 NM

40 meters

*Applies to final segment only. Apply GPS values to all other segments of the approach procedure.

3. Procedure Identification. GPS and WAAS are considered to be RNAV systems. The procedure identification begins with “COPTER RNAV (GPS).” The remainder of the identification is based on whether the landing site is a heliport or a runway.

a. U.S. Army (USA) Helicopter Runways. USA heliports that have helicopter runways chart the procedure with the letter H and the runway number. To differentiate between parallel runways, use the letter “L” or “R”; i.e., COPTER RNAV (GPS) RWY H22R.

b. IFR Approach to an IFR Runway (within 30 degrees alignment). Use the abbreviation “RWY” followed by the runway number. Examples: COPTER RNAV (GPS) RWY 22.

c. Point-in-Space (PinS) or IVH procedures to a VFR Runway. Use the magnetic bearing of the final approach course. Example: COPTER RNAV (GPS) 160°.

d. Multiple Procedures to the Same Runway. Where more than one approach, using the same final approach guidance is developed to the same location, identify each location/guidance combination with an alphabetical suffix beginning at the end of the alphabet; e.g., COPTER RNAV (GPS) Z RWY 22 (first procedure), COPTER RNAV (GPS) Y RWY 22 (second procedure), COPTER RNAV (GPS) X RWY 22 (third procedure). Identify the procedure with the lowest minimums will be identified with “Z” and the next lowest “Y.”

e. Special Approach Procedures. A procedure requires special authorization when it is an instrument flight rules (IFR) approach to a visual flight rules (VFR) heliport, reference chapter 4, paragraph 5, or one of the following conditions exists: (USAF/USA/USCG/USN not applicable).

(1) A track change at the precise final approach fix (PFAF) exceeds 30 degrees.

(2) Descent Gradient/Angle exceeds 600 ft/NM (5.64 degrees) on any IFR segment.

(3) When raising the helipoint crossing height (HCH) to greater than 10 ft in the visual segment.

(4) When a Vmini less than 70 knots indicated airspeed (KIAS) is applied.

(5) Where a bank angle other than the standard is used.

(6) When the missed approach point (MAP) to helipoint distance is less than 3,342 ft (0.55 NM).

Note: This criterion applies only to an IFR to a VFR heliport (IVH) procedure.

4. Segment Width (General). Table 2-2 lists primary and secondary width values for all segments of an RNAV approach procedure. Where segments cross* a point 30 NM from airport reference point (HRP), segment primary area width increases (expansion) or decreases (taper) at a rate of 30 degrees relative to course to the appropriate width. Secondary area expansion/taper is a straight-line connection from the point the primary area begins expansion/taper to the point the primary area expansion/taper ends. Reference to route width values is often specified as NM values measured from secondary area edge across the primary area to the secondary edge at the other side. For example, route width for segments more than 30 NM from HRP is “1-3-3-1.” See figures 2-2b and 2-2c. For distances ≤ 30 NM, the width is “0.5-1.5-1.5-0.5.” See table 2-2 and figure 2-2a.

*Note: Feeder segment width is 1-3-3-1 at all distances greater than 30 NM from HRP. A segment designed to cross within 30 NM of the HRP more than once does not taper in width until the 30 NM limit is crossed for approach and landing; i.e., crosses the limit for the last time before landing. A missed approach segment designed to cross a point 30 NM of the HRP more than once expands when it crosses the boundary the first time and remains expanded.

Segment

En Route, Feeder,

Initial & Missed

Approach

Feeder, Initial, Missed Approach

Intermediate

Table 2-2. RNAV Linear Segment Width (NM) Values.

Primary Area Half-Width (p) Secondary Area (s)

± 3.00 1.00 > 30

NM from

ARP

1-3-3-1

± 1.50 0.5 ≤ 30

NM from

ARP

0.5-1.5-1.5-0.5

Continues initial segment width until 2 NM prior to PFAF. Then tapers uniformly to final segment width.

Continues initial segment width until 2 NM prior to PFAF. Then tapers to final segment width.

Figure 2-2a. Segment Width Variables.

S P S P

Figure 2-2b. En Route/Feeder/Initial

Segment Cross Section (> 30 NM).

1.0 NM

Course Centerline

3.0 NM 3.0 NM

1,0 00’

500 ’

1.0 NM

d

Figure 2-2c. En Route/Feeder/Initial Segment

Cross Section Mountainous (> 30 NM).

g

1.0 NM

COURSE CENTERLINE

3.0 NM 3.0 NM

2,000’

500’

1.0 NM

d

a. Width Changes at 30 NM from HRP/ARP.

(1) Width Changes at 30 NM from HRP (non-RF). Receiver sensitivity changes at 30 NM from HRP. From the point the designed course crosses 30 NM from HRP, the primary

OEA can taper inward at a rate of 30 degrees relative to course from ± 3 NM to ± 1.5 NM. The secondary area tapers from a 1 NM width when the 30 NM point is crossed to a 0.5 NM width abeam the point the primary area reaches the ± 1.5 NM width. The total along-track distance required to complete the taper is approximately 1.73 NM (10,524.14 ft). Segment width tapers regardless of fix location within the tapering section unless a turn is associated with the fix. Delay OEA taper until the turn is complete and normal OEA turn construction is possible (see figure 2-3a).

Figure 2-3a. Segment Width Changes at 30 NM.

3 NM 3 NM 1 NM 1 NM

1.5 NM 1.5 NM 0.5 NM 0.5 NM

3 NM 3 NM 1 NM 1 NM

1.5 NM 1.5 NM 0.5 NM 0.5 NM

30 NM from ARP

30 NM from ARP

1 NM =1.73 tan(30)

1 NM =1.73 tan(30)

(2) Width Changes at 30 NM from HRP/ARP (RF). When the approach segment crosses the point 30 NM from airport reference point in an RF leg, construct the leg beginning at a width of 1-3-3-1 prior to the 30 NM point and taper to 0.5-1.5-1.5-0.5 NM width inside the 30 NM point. Calculate the perpendicular distance (Bprimary, Bsecondary) from the RF segment track centerline to primary and secondary boundaries at any along-track distance (specified as degrees of RF arc “α”) from the point the track crosses the 30 NM point using formula 2-1 (see figure 2-3b, apply formula 2-3c to find the RF arc radius).

Formula 2-1. RF Segment Taper Width.

3-1.5 180 D ⋅ D= α = ⎛ π ⎞ π ⋅R tan 30 ⋅ ⎜ ⎟ ⎝ 180 ⎠ Calculates degrees of arc ( ) to complete taper α

φ⋅π ⋅R B = − 3 1.5⋅ primary 180 D ⋅

φ⋅π ⋅R B = − 4 2 ⋅ secondary 180 D ⋅

Where:

D = taper distance R = RF leg radius

φ = degrees of arc (RF track)

Note: “D” will be in the same units as “R”

D=(3-1.5)/tan(30*π/180)

α = (180*D)/(π*R) Bprimary = 3-1.5*(φ*π*R)/(180*D)

Bsecondary = 4-2*(φ*π*R)/(180*D)

Calculator

R

Click here

to calculate

φ

α

D

Bprimary

Bsecondary

°

°

Figure 2-3b. Segment Width Changes in RF Leg.

R

R

φ

α

D

30 NM from ARP

Bsecondary

Bprimary

R F A rc C e n te r

5. Calculating the Turn Radius (R). The design turn radius value is based on four variables: indicated airspeed, assumed tailwind, altitude, and bank angle. Calculate R using formula 2-3c. Apply the indicated airspeed from table 2-3 for the highest speed helicopter category that will be published on the approach procedure. Apply the highest expected turn altitude value. Apply the appropriate bank angle from table 2-4 and formula 2-2 to determine the vertical path altitude (VPalt).

Formula 2-2. Vertical Path Altitude.

⎛ π ⎞ D tan θ⋅ ⋅ Z ⎜ ⎟ ⎝ 180 ⎠ r VP = e ⋅ + r PFAF −r alt ( alt )

Where:

PFAFalt = Designed PFAF MSL altitude

θ = glidepath angle DZ = distance (ft) from PFAF to fix

Note: If DZ is a NM value, convert to feet by multiplying NM by 1852/0.3048

e^((DZ*tan(θ*π/180))/r)*(r+PFAFalt)-r

Calculator

PFAFalt

θ

DZ

VPalt

Click here

to calculate

Note: Determine the highest altitude within a turn by:

For approach –calculate the vertical path altitude (VPalt) by projecting a 3-degree vertical path from the PFAF along the designed nominal flight track to the turn fix.

For missed approach highest altitude in a turn, apply (a) or (b), and (c).

(a) Turn-At-A-Fix, project a vertical path along the nominal flight track from the SOC point and altitude to the turn fix, that rises at a rate of 400 ft/NM (Helicopter) or a higher rate if a steeper climb gradient is specified. Compare the vertical path altitude at the fix to the minimum published fix altitude, apply the higher of the two;

(b) Turn-At-An-Altitude, apply the climb-to-altitude;

(c) Plus an additive, (Turn-At-A-Fix (FO) and Turn-At-An-Altitude) based on a continuous climb of 400 ft per 12 degrees of turn [ φ*400/12 ]). The turn altitude must not be higher than the published missed approach altitude.

Helicopter example: 900 ft would be added for a turn of 27 degrees, 767 ft would be added for 23 degrees, 333 ft for 10 degrees of turn.

Step 1: Determine the true airspeed (KTAS) for the turn using formula 2-3a. Locate and use the appropriate knots indicated airspeed (KIAS) from table 2-3. Use the highest altitude within the turn.

°

Formula 2-3a. True Airspeed.

( )

( )

KIAS KTAS 2.628 V 171233 288 15 0.00198 alt V

288 0.00198 alt

⋅ ⋅ + − ⋅ =

− ⋅

where alt = aircraft MSL elevation

VKIAS = knots indicated airspeed

(VKIAS*171233*((288+15)-0.00198*alt)^0.5)/(288-0.00198*alt)^2.628

Calculator

VKIAS

alt

VKTAS

Click here

to calculate

Table 2-3. Helicopter Indicated Airspeeds (Knots).

Indicated Airspeed Segment

Civil Military

Feeder, Initial, Intermediate 140 140

Final, Missed Approach 70 90

Step 2: Calculate the appropriate tailwind component (VKTW) using formula 2-3b for the highest altitude within the turn. EXCEPTION: If the MSL altitude is 2,000 ft or less above airport elevation, use 30 knots.

Formula 2-3b. Tailwind.

= ⋅ + KTW V 0.00198 alt 47 where alt = highest turn altitude

Note: If “alt” is 2,000 or less above

airport elevation, then VKTW = 30

0.00198*alt+47

Calculator

alt

VKTW

Click here

to calculate

Note: Greater tailwind component values may be used where data indicates higher wind conditions are likely to be encountered. Where a higher value is used, it must be recorded in the procedure documentation.

Step 3: Calculate R using formula 2-3c.

Formula 2-3c. Turn Radius.

( )

2

KTAS KTW

angle

V V R

tan bank 68625.4 180

+ = π ⎛ ⎞ ⋅ ⋅ ⎜ ⎟ ⎝ ⎠ where bankangle = assumed bank angle (normally 11° or 14° for Helicopter)

(VKTAS+VKTW)^2/(tan(bankangle*π/180)*68625.4)

Calculator

VKTAS

VKTW

bankangle

R

Click here

to calculate

Note: Use formula 2-8 to verify the required bank angle does not exceed the design bank angle (11 or 14 degrees), see table 2-4.

Table 2-4. Bank Angles.

Knots True Airspeed

(KTAS) < 90 ≥ 90

Bank Angle

(In degrees) 11.0 14.0

6. Turn Construction. If the outbound course from a fix differs by more than 0.03 degrees from the inbound course to the fix (courses measured at the fix), a turn is indicated.

a. Turns at Fly-Over Fixes (see figures 2-4 and 2-5).

(1) Extension for Turn Delay. Turn construction incorporates a delay in start of turn to account for pilot reaction time and roll-in time (rr). Calculate the extension distance in feet using formula 2-4a (terminal) or formula 2-4b (feeder and en route).

°

Formula 2-4a. Reaction &

Roll Dist. (Terminal).

KTAS

1852 0.3048 rr 6 V 3600 = ⋅ ⋅

6*1852/0.3048/3600*VKTAS

Calculator

VKTAS

rr

Click here

to calculate

Note: 6 second delay

Formula 2-4b. Turn Delay

(En Route, Feeder).

KTAS KTW rr=8 (V +V )

1852 0.3048 3600 ⋅ ⋅

8*(1852/0.3048/3600)*(VKTW+VKTAS)

Calculator

VKTW

VKTAS

rr (ft)

Click here

to calculate

Note: 8 second delay

Step 1: Determine R. See formula 2-3c.

Step 2: Determine rr. See formula 2-4a or formula 2-4b.

Step 3: Establish the baseline for construction of the turn expansion area as the line perpendicular to the inbound track at a distance past the turn fix equal to (ATT+rr).

Step 4: On the baseline, locate the center points for the primary and secondary turn boundaries. The first is located at a distance R from the non-turning side primary boundary. The second is located at a distance R from the turning side secondary boundary (see figures 2-4 and 2-5).

Step 5: From these center points construct arcs for the primary boundary of radius R. Complete the secondary boundary by constructing additional arcs of radius (R+WS) from the same center points. (WS=width of the secondary). This is shown in figures 2-4 and 2-5.

Step 6: The arcs constructed in step 5 are tangent to the outer boundary lines of the inbound segment. Construct lines tangent to the arcs based on the first turn point tapering inward at an angle of 30 degrees relative to the outbound track that joins the arc primary and secondary boundaries. If both the inner and outer arcs lie outside subsequent segment boundary lines, but the resulting tapering line tangent points lie inside the subsequent segment boundary lines, consider the expanded boundary connection points to be the intersection of the arc and the subsequent segment boundary lines. If the arcs from the second turn point are inside the tapering lines as shown in figure 2-4, then they are disregarded and the expanded area construction is completed. If not, proceed to step 7.

This graphic depicts Fly-over with no second arc exp

ansion.

Step 7: If both the inner and outer arcs lie outside the tapering lines constructed in step 6, connect the respective inner and outer arcs with tangent lines and then construct the tapering lines from the arcs centered on the second center point as shown in figure 2-5.

Step 8: The inside turn secondary boundary is the intersection of the preceding and succeeding segment secondary boundaries. The inside turn primary boundary is an arc of secondary-width radius joining the preceding and succeeding segment primary boundaries.

SECONDARY AREA

PRIMARY AREA

Evaluate the inbound-segment secondary area truncated by the arc as primary area by both segments. Both segments also evaluate the secondary area inside the arc (see figures 2-4 and 2-5)

This graphic depicts fly-over with second arc exp

ansion.

The inbound OEA end (± ATT) is evaluated for both inbound and outbound segments.

(2) Minimum length of TF leg following a fly-over turn. The leg length of a TF leg following a fly-over turn must be sufficient to allow the aircraft to return to course centerline. Determine the minimum leg length (L) using DTA distance from formula 2-5 and formula 2-6.

Formula 2-5. Distance of Turn Anticipation.

DTA R tan 2 180

φ π ⎛ ⎞ = ⋅ ⎜ ⋅ ⎟ ⎝ ⎠ Where:

R = turn radius from formula 2-3c

φ = degrees of heading change

DTA ATT

φ

R

R*tan(φ/2*π/180)

Calculator

R Click here

to calculate

φ

DTA

°

-

Formula 2-6. TF Leg Minimum Length Following Fly Over Turn.

( )

φ φ φ

φ

φ

φ φ

i

i

i i

i i i

0

0.5

.

0 5

5

.

(1+cos( 1)) 2 L=R1 sin( 1)+2 sin acos +R2 tan( ), 2 2

2 L=R1 sin( 1)+4-3 -3 cos( 1) +R2 tan( )

180 If 1 < acos(3 -1), then π

e se

2

l ⎛ ⎞ ⎛ ⎞ ⎛ ⎞ ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ ⎝ ⎠ ⎝ ⎠ ⎝ ⎠

Where:

R1 = turn radius (NM) at the segment initial fix (formula 2-3c) R2 = turn radius (NM) at the segment termination fix (zero if no fly-by turn)

φ1 = turn magnitude at the segment initial fix φ2 = turn magnitude at the segment termination fix

L

DTA

R1 R1

R1

φ

R2

φ2

1

If φ1 <180/π*acos(3^0.5-1), then R1*(sin(φ1*π/180)+2*sin(acos((1+cos(φ1*π/180))/2)))+R2*tan((φ2/2)*π/180), else R1*(sin(φ1*π/180)+4-3^0.5-3^0.5*cos(φ1*π/180))+R2*tan((φ2/2)*π/180)

Calculator

R1

R2

φ1

φ2

L

Click here

to calculate

°

°

b. Fly-By Turn. See figure 2-6.

Step 1: Establish a line through the turn fix that bisects the turn angle. Determine Turn Radius (R). See formula 2-3c. Scribe an arc (with origin on bisector line) of radius R tangent to inbound and outbound courses. This is the designed turning flight path.

Step 2: Scribe an arc tangent to the inner primary boundaries of the two segment legs

Primary Area Half-width with a radius equal to R + 2 (example: half width of 2 NM, the radius would be

R+1.0 NM).

Step 3: Scribe an arc that is tangent to the inner secondary boundaries of the two segment legs using the origin and radius from step 2 minus the secondary width.

Step 4: Scribe the primary area outer turning boundary with an arc with a radius equal to the segment half width centered on the turn fix.

Step 5: Scribe the secondary area outer turning boundary with the arc radius from step 4 plus the secondary area width centered on the turn fix.

This graphic depicts fly-by turn constr

uction.

-

(1) Minimum length of track-to-fix (TF) leg following a fly-by turn. Calculate the minimum length for a TF leg following a fly-by turn using formula 2-7.

Formula 2-7. TF Leg Minimum

Length Following Fly by Turn.

1 2 L R1 tan( ) R2 ( ) 2 2 φ φ = ⋅ + ⋅

Where: R1 = Turn radius at the segment initial fix (formula 2-3c) R2 = Turn radius at the segment termination (formula 2-3c)

Note: Zero when no turn φ1 = turn magnitude at the segment initial fix

φ2 = turn magnitude, if any at the segment termination fix

φ1 φ2

L

R1 R2

DTA1 DTA2

R1*tan(φ1/2*π/180)+R2*tan(φ2/2*π/180)

Calculator

R1

R2

φ1

φ2

L

Click here

to calculate

°

°

c. Radius-to-Fix (RF) Turn. Incorporation of an RF segment may limit the number of aircraft served by the procedure. RF legs are used to control the ground track of a turn where obstructions prevent the design of a fly-by or fly-over turn, or to accommodate other operational requirements.* The curved leg begins tangent to the previous segment course at its terminating fix and ends tangent to the next segment course at its beginning fix (see figure 2-7). OEA construction limits turn radius to a minimum value equal-to or greater-than the OEA (primary and secondary) half-width. The RF segment OEA boundaries are parallel arcs.

*Note: RF legs segments are not applicable to the final segment or section 1 of the missed approach segment. RF legs in the intermediate segment must terminate at least 2 NM prior to the PFAF. Where RF legs are used, annotate the procedure (or segment as appropriate) “RF Required.” Use Order 8260.52, table 1-3 for VKTW values for radius calculations for RF legs.

Step 1: Determine the segment turn radius (R) that is required to fit the geometry of the terrain/airspace. Enter the required radius value into formula 2-8 to verify the resultant bank angle is ≤ 20 degrees (maximum allowable bank angle). Where a bank angle other than standard is used, annotate the value in the remarks section of the FAA Form 8260-9 or appropriate military procedure documentation form.

Formula 2-8. RF Bank Angle.

( )

2

KTAS KTW angle

V V 180 bank a tan R 68625.4

⎛ ⎞ + ⎜ ⎟ = ⋅ ⎜ ⎟ ⋅ π ⎝ ⎠

Where:

VKTAS = value from formula 2-3a

VKTW = value from Order 8260.52, table 1-3

R = required radius

atan((VKTAS+VKTW)^2/(R*68625.4))*180/π

Calculator

VKTAS

VKTW

R

bankangle

Click here

to calculate

Calculate RF segment length using formula 2-9.

°

Formula 2-9. RF Segment Length.

length

R Segment 180 π ⋅ ⋅φ =

Where:

R = RF segment radius (answer will be in the units entered)

φ = # of degrees of ARC

(heading change)

π*R*φ/180

Calculator

R

φ

Segmentlength

Click here

to calculate

Step 2: Turn Center. Locate the turn center at a perpendicular distance R from the preceding and following segments.

Step 3: Flight path. Construct an arc of radius R from the tangent point on the preceding course to the tangent point on the following course.

Step 4: Primary area outer boundary. Construct an arc of radius R+Primary area halfwidth from the tangent point on the preceding segment primary area outer boundary to the tangent point on the following course primary area outer boundary.

Step 5: Secondary area outer boundary. Construct an arc of radius R+Primary area halfwidth+secondary area width from the tangent point on the preceding segment secondary area outer boundary to the tangent point on the following course secondary area outer boundary.

Step 6: Primary area inner boundary. Construct an arc of radius R-Primary area halfwidth from the tangent point on the preceding segment inner primary area boundary to the tangent point on the following course inner primary area boundary.

Step 7: Secondary area inner boundary. Construct an arc of radius R-(Primary area halfwidth+secondary area width) from the tangent point on the preceding segment inner secondary area boundary to the tangent point on the following course inner secondary area boundary.

°

Figure 2-7. RF Turn Construction.

Evaluated as both segments B and C

Evaluated as both segments A and B

Determine Radius (R)

Locate Turn Center

SEGMENT A

SEGMENT B

STEP 1

STEP 2

SEGMENT C

R

R

STEP 6

STEP 7

STEP 4

STEP 3

STEP 5

STEP 5

d. RNAV TF/VA/VI/CF leg followed by a DF Leg. Calculate minimum DF segment length using formula 2-9b.

Formula 2-9b. RNAV DF Leg Minimum

Length following TF/VA/VI/CF Legs.

( ) φ

φ

φ

2 30 L 4 R sin , else 2

If 30 th

L 2 R sin

en

⎛ ⎞ ⎛ + ⎞ = ⋅ ⋅⎜ ⎟ ⎜ ⎟ ⎝ ⎠ ⎝ ⎠ = ⋅ ⋅

>

Where:

R = turn radius (NM) at the segment initial fix (formula 2-3c)

φ = turn magnitude at the segment initial fix

L

L

φ

L φ

φ

If φ>30 then L= 4*R*(sin((φ+30)/2*π/180))∧2, else L=2*R*sin(φ*π/180)

Calculator

R Click here

to calculate

φ

L

7. Helicopter Initial and Intermediate Descent Gradient. The optimum descent gradient in the initial and intermediate segment is 400 ft/NM (6.58%, 3.77°); maximum is 600 ft/NM (9.87%, 5.64°). Where higher descent gradients are required, Order 8260.3, Volume 1, paragraph 1110 applies.

a. Calculating Descent Gradient (DG). Determine total altitude lost between the plotted positions of the fixes. Determine the distance (D) in NM. Divide the total altitude lost by D to determine the segment descent gradient using formula 2-10 (see figure 2-8).

Figure 2-8. Calculating Descent Gradient.

FIX

2,900

( ) a

FIX

1,500

( ) b

5.14 ( ) D

r a r ln r b DG D

+ ⎛ ⎞ ⋅ ⎜ ⎟ + ⎝ ⎠ =

Where:

a = beginning altitude b = ending altitude D = distance (NM) between fixes

Formula 2-10. Descent Gradient.

r*ln((r+a)/(r+b))/D

Calculator

a

b

D

DG

Click here

to calculate

8. Feeder Segment. When the initial approach fix (IAF) is not part of the en route structure, it may be necessary to designate feeder routes from the en route structure to the IAF. The feeder segment may contain a sequence of TF segments (and/or RF segments). The maximum course

change between TF segments is 90 degrees (70 degrees preferred). Formula 2-3c note applies. Chapter 2, paragraph 6 turn construction applies. The feeder segment terminates at the IAF (see chapter 2, figures 2-4, 2-5, and 2-6 for construction).

a. Length. The minimum length of a sub-segment is determined under chapter 2, paragraph 6a(2) or 6b(1) as appropriate. The maximum length of a sub-segment is 50 miles. The total length of the feeder segment should be as short as operationally possible.

b. Width. Primary area width is ± 3.0 NM from course centerline; secondary area width is 1.0 NM (1-3-3-1). These widths apply from the feeder segment initial fix to the approach IAF/termination fix.

c. Obstacle Clearance. The feeder segment OEA begins at the beginning fix early ATT and ends at the ending fix late ATT. The minimum ROC over areas not designated as mountainous under Federal Aviation Regulation (FAR) 95 is 1,000 ft. The minimum ROC within areas designated in FAR 95 as “mountainous” is 2,000 ft. Order 8260.3, Volume 1, paragraphs 1720b(1), 1720b(2), and 1721 apply. The published minimum feeder route altitude must provide at least the minimum ROC value and must not be less than the altitude established at the IAF. (Refer to figures 2-2a, 2-2b and apply formula 2-12a for standard secondary ROC.) Apply formula 2-12b for designated mountainous area calculations (formulas are applicable for en route, feeder, and initial).

Note: ROC additive, see 8260.3, Volume 1, paragraph 1720.

d. Descent Gradient, Helicopter (feeder, initial, intermediate segments). The optimum descent gradient in feeder, initial, and intermediate segments is 400 ft/NM (6.58%, 3.77°); maximum is 600 ft/NM (9.87%, 5.64°). Where higher descent gradients are required, Order 8260.3, Volume 1, paragraph 1110 applies.

e. Minimum Crossing Altitude (MCA). Establish an MCA when an obstacle prevents a normal climb to a higher minimum en route altitude (MEA). The normal climb gradient is shown in table 2-5. When a MCA is required, chart the required climb gradient and rate of climb on the procedure.

Table 2-5. Normal Helicopter

En Route Climb Gradient.

Gradient Level (MSL) Gradient

at or below 5,000 ft 300 ft per NM

5,001 ft through 10,000 ft 240 ft per NM

OCS Slope

20.25:1

25.3:1

The MCA computation is based on the distance from the nearest fix displacement tolerance line to the obstacle. The computation is rounded to the next higher 100-ft increment (see figure 2-9 for an example MCA computation).

Note: The USA standard climb gradient is 400 ft/NM for all altitudes.

f. Determine MCA. Apply formula 2-11a, or 2-11b to determine MCA.

A

L

MCA

A

L

MCA

Formula 2-11a. MCA Sea Level to 5,000 ft MSL.

MCA = A-300 L ⋅ Where:

A = “Climb to” MSL Altitude L = Length of segment (NM)

A-300*L

Calculator

Click here

to calculate

Formula 2-11b. MCA 5,000 - 10,000 ft MSL.

A-5000 MCA = 5000 − 300(L­ ) 2 0 4 Where:

A = “Climb to” MSL Altitude

L = Length of segment (NM)

5000-300*(L-(A-5000)/240)

Calculator

Click here

to calculate

Figure 2-9. Minimum Crossing Altitude (MCA).

PLAN VIEW

SECONDA RY

FIX TOLERA NCE LINE NEA REST TO OBSTACLE

PR OFILE VIEW

SECONDA RY

PRIMARY

20. 3 NM

22. 3 NM

9.2 NM

7,6 70’ MSL

5,6 70’ MSL

5,0 00’ MSL

11.1 NM

X

2.0 NM

2,300 ’ M SL

300 ’/NM

240 ’/NM

2,0 00’ MEA (M SL)

2,0 00’ ROC

MCA STARTING POINT

Step 1: Add 2,000 ft mountainous ROC to MSL height of obstacle.

Step 2: Apply formula 2-11a or 2-11b to determine the MCA.

Chapter 2. General Criteria

Section 2. Terminal Segments

9. Initial Segment. The initial segment begins at the IAF and ends at the intermediate fix (IF). The initial segment may contain sequences of straight sub segments (see figure 2-10). Chapter 2, paragraphs 9b, 9c, 9d, and 9e apply to all sub segments individually. The total length of all sub segments must not exceed 50 NM. For descent gradient limits, see chapter 2, paragraph 8d.

IAF

Figure 2-10. Initial Sub Segments.

Sub Segment

Sub Segment

FAF

Initial Segment

IF

a. Course Reversal. The optimum design incorporates either the basic Y or T configuration (see AIM or FHP for further BASIC T/Y information). This design eliminates the need for a specific course reversal pattern. Where the optimum design cannot be used and a course reversal is required, establish a holding pattern at the initial, or intermediate approach fix. See chapter 2, paragraph 9f(2). The maximum course change at the fix (IAF/IF) is to 90 degrees (70 degrees above FL 190).

b. Alignment. Design initial/initial and initial/intermediate TF segment intersections with the smallest amount of course change that is necessary for the procedure. No course change is optimum. Where a course change is necessary, it should normally be limited to 70 degrees or less; 30 degrees or less is preferred. The maximum allowable course change between TF segments is 90 degrees.

P

Note: For USA, limit initial segment turn to a MAXIMUM of 60 degrees with a basic “Y” approach configuration for COPTER RNAV (GPS) procedures.

c. Area – Length. The maximum segment length (total of sub segments) is 50 NM. Minimum length of sub segments is determined as described in chapter 2, paragraphs 6a(2) and 6b(1).

d. Area – Width (see table 2-2).

e. Obstacle Clearance. The initial OEA begins at the segment beginning fix early ATT and ends at the segment ending fix late ATT. Apply 1,000 ft of ROC over the highest obstacle in the primary OEA. The ROC in the secondary area is 500 ft at the primary boundary tapering uniformly to zero at the outer edge (see figure 2-11).

Figure 2-11. En route/Feeder/Initial Segment ROC.

P S S

1000’ 500’ 500’

Note: Allowance for precipitous terrain should be made as specified in Order 8260.3, Volume 1, paragraph 3.2.2b.

Calculate the secondary ROC values using formula 2-12a.

Formula 2-12a. En route/Feeder/Initial

Secondary ROC (Standard).

⎛ ⎞ = ⋅ − ⎜ ⎟ ⎝ ⎠ sec ondary

d ROC 500 1 D

Where:

D = width (ft) of secondary d = distance (ft) from edge of primary

area measured perpendicular to boundary

500*(1-d/D)

Calculator

d

D

ROCsecondary

Click here

to calculate

Calculate the secondary ROC values for designated mountainous areas using formula 2-12b. Consult Order 8260.3 para 1720 b (1) for possible adjustments to formula output.

Formula 2-12b. En Route/Feeder/Initial

Secondary ROC (Mountainous).

⎛ ⎞ = ⋅ − + ⎜ ⎟ ⎝ ⎠ sec ondary

d ROC 500 1 1000 D

Where:

D = width (ft) of secondary d = distance (ft) from edge of primary

area measured perpendicular to boundary

500*(1-d/D)+1000

Calculator

d

D

ROCsecondary

Click here

to calculate

f. Holding Pattern Initial Segment. A holding pattern may be incorporated into the initial segment procedure design where an operational benefit can be derived; e.g., arrival holding at an IAF, course reversal pattern at the IF, etc. See FAA Order 7130.3, Holding Pattern Criteria, for RNAV holding pattern construction guidance.

(1) Arrival Holding. Ideally, the holding pattern inbound course should be aligned with the subsequent TF leg segment (tangent to course at the initial fix of the subsequent RF segment). See figure 2-12a. If the pattern is offset from the subsequent TF segment course, the subsequent segment length must accommodate the resulting DTA requirement. Establish the minimum holding altitude at or above the IAF/IF (as appropriate) minimum altitude. MEA minimum altitude may be lower than the minimum holding altitude.

Figure 2-12a. Arrival Holding Example.

(2) Course Reversal. Ideally, establish the minimum holding altitude as the minimum IF fix altitude (see figure 2-12b). In any case, the published holding altitude must result in a suitable descent gradient in the intermediate segment: optimum descent gradient in the initial and intermediate segment is 400 ft/NM (6.58%, 3.77°); maximum is 600 ft/NM (9.87%, 5.64°). If the pattern is offset from the subsequent TF segment course, the subsequent segment length must accommodate the resulting DTA requirement. Maximum offset is 90 degrees.

Figure 2-12b. Course Reversal Example.

10. Intermediate Segment. The intermediate segment primary and secondary boundary lines connect abeam the plotted position of the PFAF at the appropriate primary and secondary final segment beginning widths.

a. Alignment (Maximum Course Change at the PFAF). LNAV & LP. Align the intermediate course within 30 degrees of the final approach course (30 degrees maximum course change).

b. Length (Fix to Fix). The minimum Helicopter category segment length is 2 NM. Where turns over 30 degrees at the IF are required, the minimum is 3 NM. Where turns to and from the intermediate segment are necessary, determine minimum segment length using formula 2-6 or formula 2-7, as appropriate.

c. Width. The intermediate segment primary area tapers uniformly from ± 1.5 NM at a point 2 NM prior to the PFAF to the outer boundary of the X OCS abeam the PFAF (1 NM past the PFAF for LNAV). The secondary boundary tapers uniformly from 1 NM at a point 2 NM prior to the PFAF to the outer boundary of the Y OCS abeam the PFAF (1 NM past the PFAF for LNAV ). See figure 2-13a.

Figure 2-13a. RNAV Intermediate Segment (LNAV Final).

PFAF

IF

1.5 NM

0.5 NM

0.5 NM

1.5 NM

Evaluated as both

segments A & B

Segment B

Segment A

2 NM

If a turn is designed at the IF, it is possible for the inside turn construction to generate boundaries outside the normal segment width at the taper beginning point 2 miles prior to the PFAF. Where these cases occur, the inside (turn side) boundaries are a simple straight line connections as illustrated in figure 2-13b.

Figure 2-13b. RNAV Turn at IF (LNAV Final).

Evaluated as both

segments A & B

2 NM

Maximum turn at the PFAF is 30 degrees. When a PFAF turn is constructed, minimum FAS length is 3 NM for turns greater than 15 degrees. Where the RNAV or LP intermediate course is not an extension of the FAC, use the following construction (see figure 2-13c).

(1) LNAV Offset Construction. Where LNAV intermediate course is not an extension of the final course, use the following construction (see figure 2-13c, upper graphic).

Step 1: Construct line A perpendicular to the intermediate course 2 NM prior the PFAF.

Step 2: Construct line B perpendicular to the intermediate course extended 1 NM past the PFAF.

Step 3: Construct the inside turn boundaries by connecting the points of intersection of line A with the turn side intermediate segment boundaries with the intersection of line B with the turn side final segment boundaries.

Step 4: Construct arcs centered on the PFAF of 1 NM and 1.5 NM radius on the nonturn side of the fix.

Step 5: Connect lines from the point of intersection of line A and the outside primary and secondary intermediate segment boundaries to tangent points on the arcs constructed in step 4.

Step 6: Connect lines tangent to the arcs created in step 4 that taper inward at 30 degrees relative to the FAC to intersect the primary and secondary final segment boundaries as appropriate.

The final segment evaluation extends to a point ATT prior to the angle bisector. The intermediate segment evaluation extends ATT past the angle bisector. Therefore, the area within ATT of the angle bisector is evaluated for both the final and intermediate segments.

(2) LP Offset Construction. Where LP intermediate course is not an extension of the final course, use the following construction (see figure 2-13c, lower graphic).

Step 1: Construct line A perpendicular to the intermediate course 2 NM prior the PFAF.

Step 2: Construct line B perpendicular to the intermediate course extended 1 NM past the PFAF.

Step 3: Construct the inside turn boundaries by connecting the points of intersection of line A with the turn side intermediate segment boundaries with the intersection of line B with the turn side final segment boundaries.

Step 4: Connect lines from the point of intersection of line A and the outside primary and secondary intermediate segment boundaries to the final segment primary and secondary final segment lines at a point perpendicular to the final course at the PFAF.

Note: DA must not occur at a greater distance from HRP than the turn-side point of intersection of the expanded outer boundary line with the final segment secondary boundary (intersection of line “B” with secondary boundary in figure 2-13c lower graphic). If a higher DA is required, then the degree of offset must be less.

The final segment evaluation extends to a point ATT prior to the angle bisector. The intermediate segment evaluation extends ATT past the angle bisector. Therefore, the area within ATT of the angle bisector is evaluated for both the final and intermediate segments.

Figure 2-13c. Offset LNAV/LP Turn at PFAF Construction.

Intermediate

Evaluated as both, Intermediate and Final segments

STEP 3

STEP 4 STEP 6

STEP 5

STEP 2

STEP 1

A

B

B

A

0.5 NM

IF

1.5 NM

1.5 NM

0.5 NM

30°

PFAF

1 NM 2 NM

FAS

A

B

B

A

PFAF FAS

Intermediate

STEP 1

Bisector

STEP 2

STEP 3

STEP 4

0.5 NM

IF

1.5 NM

1.5 NM

0.5 NM

1 NM

<30°

Evaluated as both Intermediate and Final segments

2 NM

(3) RF intermediate segments. Reserved.

d. Obstacle Clearance. The intermediate OEA begins at the segment beginning fix early ATT and ends at the segment ending fix late ATT. Apply 500 ft of ROC over the highest obstacle in the primary OEA. The ROC in the secondary area is 500 ft at the primary boundary tapering uniformly to zero at the outer edge (see figure 2-14).

Figure 2-14. Intermediate Segment ROC.

S S P

500’

P

ROC adjustment if required

Calculate intermediate secondary ROC values using formula 2-13.

( )

primary sec ondary

S

d ROC 500 adj 1 W

⎛ ⎞ = + ⋅ − ⎜ ⎟ ⎝ ⎠ Where:

dprimary = perpendicular distance (ft) from edge of primary area

WS = Width (ft) of the secondary area adj = TERPS para 3.2.2 adjustments

Formula 2-13. Intermediate Secondary ROC.

(500+adj)*(1-dprimary/WS)

Calculator

WS Adj

dprimary

ROCsecondary

here

to calculate

Click

e. Minimum IF to FHP Distance (applicable for LP procedures with no turn at PFAF). Locate the IF at least dIF (NM) from the FHP (see formula 2-14).

Formula 2-14. Minimum IF Distance.

d 0.3048 dIF = 0.3 ⋅ − d ⋅ a 1852 Where:

d = distance (ft) from FPAP to FHP

a = width (ft) of azimuth signal at FHP

Note: See chapter 4, table 4-1, column 3

a

0.3*d/a-d*0.3048/1852

Calculator

d

dIF

Click here

to calculate

Chapter 2. General Criteria

Section 3. Basic Vertically Guided

Final Segment General Criteria

11. Determining Precise Final Approach Fix/Final Approach Fix (PFAF/FAF) Coordinates (see figure 2-15 fixed-wing example).

Figure 2-15. Determining PFAF Distance to LTP (Example).

ILS PFAF Calculation

Curved Line BaroVNAV

Straight Line ILS

Baro VNAV PFAF

Calculation

Curved Line BaroVNAV

coded θ

Intermediate

Segment M

inimum Altitude

DPFAF form

ula 2-15

DPFAF form

ula 2-15

Geodetically calculate the latitude and longitude of the PFAF using the true bearing from the Heliport Reference Point (HRP) to the PFAF and the horizontal distance (DPFAF) from the HRP to the point the glidepath intercepts the intermediate segment altitude. The LNAV (BaroVNAV) glidepath is a curved line (logarithmic spiral) in space. Calculation the PFAF distance from the HRP using formula 2-15 (calculates the LNAV PFAF distance from HRP; i.e., the point the curved line BaroVNAV based vertical path intersects the minimum intermediate segment altitude (see Order 8260.54A, chapter 2 for additional information).

Formula 2-15. LNAV PFAF.

⎛ ⎞ + ⋅ ⎜ ⎟ + + ⎝ ⎠ = π ⎛ ⎞ ⎜θ ⋅ ⎟ ⎝ ⎠

elev PFAF

r alt ln r r HRP HCH D

tan 180

where alt = minimum intermediate segment altitude HRPelev = HRP MSL elevation

HCH = Heliport Crossing Height value

r = 20890537 θ = glidepath angle

(ln((r+alt)/(r+HRPelev+HCH))*r)/tan(θ*π/180)

Calculator

HRPelev

HCH

θ

alt

DPFAF

Click here

to calculate

12-15. Reserved.

16. Common Fixes. Design all procedures published on the same chart to use the same sequence of charted fixes.

17. Missed Approach Segment (MAS) Conventions. Figure 2-16 defines the MAP point OEA construction line terminology and convention for section 1.

°

Figure 2-15. MAS Point/Line Identification.

Line CD begins, Line AB ends Section 1 Line EF ends MAP ATT (if used) Line GH ends distance to accommodate pilot reaction time Line JK marks SOC, ends Section 1A Line PP’ indicates the late turn point (if used) Line P’P” may be used when required Line LL’ indicates the early turn point (if used) Line L’L’’ may be used when required

Line C-E-G-J-L-A-P

Turn Side Points

Default and Left Turn

Right Turn

MAP

SOC

C

D

E

F

G

H

J

K

L

L’

A

B

P

P’

Section 1A

MAP

SOC

D

C

F

E

H

G

K

J

L’

L

B

A

P’

P”

P”

P

Section 1A

The missed approach obstacle clearance standard is based on a minimum helicopter climb gradient of 400 ft/NM, protected by a ROC surface that rises at 304 ft/NM. The MA ROC value is based on a requirement for a 96 ft/NM (400-304 = 96) increase in ROC value from the startof-climb (SOC) point located at JK. The actual slope of the MA surface is (1 NM in feet)/304≈ 19.987. In manual application of TERPS, the rounded value of 20:1 has traditionally been applied. However, this order is written for automated application; therefore, the full value (to 15 significant digits) is used in calculations. The nominal OCS slope (MAOCSslope) associated with any given missed approach climb gradient is calculated using formula 2-16.

⎛ ⎞ + ⎜ ⎟ ⋅ − ⎜ ⎟ ⎜ ⎟ ⎜ ⎟ ⎝ ⎠

= i OCSslope

1852 r 0.3048 (CG 96) r MA r ln

Where:

CG = Climb Gradient (nominally 400 ft/NM)

Formula 2-16. Helicopter Missed

Approach OCS Slope.

CG

MAOCSslope

r*ln((1852/(.3048*(CG-96))+r)/r)

Calculator

Click here

to calculate

a. Charted Missed Approach Altitude. Apply Order 8260.3, Volume 1, paragraphs 277d and 277f to establish the preliminary and charted missed approach altitudes.

b. Climb-In-Holding. Apply Order 8260.3, Volume 1, paragraph 277e for climb-inholding guidance.

2-43 (and 2-44)

THIS PAGE INTENTIONALLY LEFT BLANK

Chapter 3. Terminal Operations

1. Approach Configuration. The BASIC “Y” or “T” approach configuration should be the basis of procedure design. Segment length is affected by altitude to be lost, fix tolerances, and turn magnitude at the fixes. The optimum design incorporates a basic Y or T configuration. This design eliminates the need for a specific course reversal pattern. Where the optimum design cannot be used and a course reversal is required, establish a holding pattern at the initial or intermediate approach fix. Public procedures should not deviate from these shape and dimension configurations unless there is an operational advantage. Construct IAFs within 25 NM of the airport reference point/heliport reference point (ARP/HRP). See chapter 2, paragraph 9 for construction methods.

Note 1: Allowance for precipitous terrain should be made as specified in Order 8260.3, Volume 1, paragraph 3.2.2b.

Note 2: For USA, limit initial segment turn to a MAXIMUM of 60 degrees with a basic “Y” approach configuration for COPTER RNAV (GPS) procedures.

Table 3-1. Helicopter GPS MINIMUM Initial/Intermediate/Final Segment Lengths.

Course Intercept Angle

(Degrees)

Minimum Leg Length

(NM)

00 – 30 2.0

> 30 - 90 * 3.0

* Final segment 30-degree MAXIMUM intercept angle for Global Positioning System (GPS) and Wide Area Augmentation System (WAAS) public procedures. Final segment 60-degree MAXIMUM intercept angle for GPS and WAAS special procedures. A turn exceeding 30 degrees at the precise final approach fix (PFAF) requires documentation of equipment capability.

a. Initial Approach Segment. The initial approach segment begins at the IAF and ends at the IF. The initial segment/subsegment obstacle evaluation area (OEA) begins at the early ATT of the segment beginning fix and ends at the late ATT of the segment/subsegment ending fix. If a special procedure requires a course change at the IAF that exceeds 90 degrees, a waiver is required and is noted on FAA Form 8260-9 (no course change exceeding 120 degrees is allowed). The IF may be identified as an along-track distance (ATD) from the PFAF. Course change at the IF must not exceed 90 degrees for public and special procedures. Construct the inbound leg of course reversal holding patterns within 30 degrees of the intermediate course (IF/IAF). Apply chapter 2, paragraph 9 for course reversal using holding pattern criteria. Do not establish a holding pattern in lieu of procedure turn at the PFAF. See chapter 2 for construction methods.

(1) Length. The initial segment begins at IAF and ends at the IF. The length should not exceed 10 NM unless operational requirements mandate a longer segment. Determine the minimum length using the greater distance from formulas 2-7, 2-8, and table 3-1.

(2) Width.

(a) Primary Area. 1.5 NM each side of the course centerline.

(b) Secondary Area. 0.5 NM on each side of the primary area.

(3) Obstacle Clearance. Provide a minimum of 1,000 ft of required obstacle clearance (ROC) in the primary area. In the secondary area, provide 500 ft of ROC at the inner edge, tapering uniformly to zero at the outer edge (see chapter 2, figure 2-12). Calculate the secondary ROC using chapter 2, formula 2-12a or formula 2-12b. Establish initial segment altitudes in 100-ft increments that meet or exceed minimum ROC.

(4) Descent Gradient for Initial Segments (see chapter 2, paragraph 7).

b. Intermediate Segment. The intermediate segment begins at the IF and ends at the PFAF. The intermediate segment OEA begins at the early ATT of the segment beginning fix and ends at the late ATT of the segment ending fix. The intermediate segment is used to prepare the helicopter speed and configuration for final approach segment entry; therefore, the gradient should be as flat as possible. At a point beginning 2.0 NM from the PFAF, construct a taper to join the final approach segment (FAS).

(1) Alignment. The maximum course change at the PFAF is 30 degrees. Course change more than 30 degrees requires Flight Standards approval.

(2) Area.

(a) Length. The intermediate segment begins at the IF and ends at the PFAF. The length should not exceed 5.0 NM (optimum length is 3.0 NM). Determine the minimum length using the greater distance from formulas 2-7, 2-8, and table 3-1.

(b) Width.

1 Primary Area. 1.5 NM each side of the segment centerline, beginning at the earliest IF position. The segment taper begins 2.0 NM prior to the plotted position of the PFAF to reach a ± 0.55 NM width at the PFAF plotted position (see chapter 2, figures 2-13a, 2-13b, and 2-13c).

2 Secondary Area. 0.50 NM on each side of the primary area.

Note: USAF/USA/USCG/USN operating at 90 KIAS: Change 0.55 NM to 0.70 NM.

(3) Obstacle Clearance. Provide a MINIMUM of 500 ft of ROC in the primary area. In the secondary area, provide 500 ft of ROC at the inner edge tapering to zero feet at the outer edge. Establish altitudes for each intermediate segment in 100-ft increments, and round to the

next higher 100-ft increment. Calculate the secondary ROC using chapter 2, formula 2-13 (see chapter 2, figure 2-14).

(4) Descent Gradient for Intermediate Segments (see chapter 2, paragraph 7).

3-3 (and 3-4)

THIS PAGE INTENTIONALLY LEFT BLANK

Chapter 4. IFR Final and Visual Segments

1. General. The approach procedure type is determined by the visual segment. The instrument flight rule (IFR) final approach segment (FAS) applies to all five types of procedures. Use the criteria in chapter 3 for the construction of the initial and intermediate segments up to the precise final approach fix (PFAF), and chapter 5 criteria for the missed approach segment construction. Apply chapter 4, paragraph 3 criteria to LNAV IFR final segments, and chapter 4, paragraph 9 to WAAS LP IFR final segments.

Note: Chapter 4 graphics are not drawn to scale

a. Final Segment Stepdown Fix (SDF). An SDF may be applied where the MDA can be lowered 60 ft, or a visibility reduction can be achieved. Order 8260.3, Volume 1, paragraph 289 applies, with the following exceptions:

(1) Establish step-down fix locations in 0.10 NM increments.

(2) The minimum distance between stepdown fixes is 1 NM.

(3) Establish stepdown fix altitudes using 20-ft increments, rounded to the next higher 20-ft increment. For example, 2104 becomes 2120.

(4) Where a Remote Altimeter Setting Source (RASS) adjustment is in use, the published stepdown fix altitude must be established no lower than the altitude required for the greatest amount of adjustment (i.e., the published minimum altitude must incorporate the greatest amount of RASS adjustment required).

(5) Descent gradient: Chapter 4, paragraphs 3a(3), 3a(4), and 3a(5) apply.

(6) Obstacles eliminated from consideration (3.5:1 area) under this paragraph must be noted in the procedure documentation (see Order 8260.19).

(7) Use formula 4-4 in chapter 4, paragraph 3a(6) concerning Order 8260.3, Volume 1, paragraph 289 to determine the OIS elevation at an obstacle and minimum fix altitude based on an obstacle height.

(8) To mitigate surface penetrations:

• Remove obstruction, or

• Reduce obstruction height, or

• Adjust the MDA, or

• Combination of options.

2. Missed Approach. Construct the missed approach for all procedures using chapter 5 criteria.

3. The five procedure types are:

• IFR to an IFR Heliport • IFR to a VFR Heliport (IVH) (Proceed Visually) • IFR to a VFR Runway (IVR) (Proceed Visually) • Point-in-Space (PinS) Approach (Proceed VFR) • IFR to an IFR Runway

a. LNAV IFR Final Approach Segment (FAS). The IFR FAS begins at the PFAF and ends at the missed approach point (MAP) (see figure 4-1). This FAS construction is unique to helicopters. It applies trapezoidal rather than the linear construction used for fixed-wing applications. Locate LNAV PFAF using chapter 2, formula 2-15. MAP location should provide the best compromise of lowest visibility and visual segment descent angle (VSDA). The optimum distance for the “Proceed Visually” MAP is 0.65 nautical mile (NM) [3/4 statute mile (SM) visibility] from the heliport. For public procedures, the preferred approach paths should be aligned with the prevailing wind direction to avoid downwind and minimize crosswind operations. Other approach/departure paths should be based on the assessment of the prevailing winds or when this information is not available, the separation between such flight paths and the preferred flight path should be at least 135 degrees.

(1) Alignment. The IFR final segment connects the PFAF to the MAP. The course change at the PFAF from the intermediate course to the final approach course (FAC) must not exceed 30 degrees. The MAP is located on the FAC between the PFAF and a point no closer to the helipoint than 0.3 NM from the visual segment reference line (VSRL). For a straight-in approach, the course change at the MAP must not exceed 30 degrees to an IFR heliport helipoint or 30 degrees from a runway centerline (RCL) extended to an IFR runway threshold (RWT). Optimum alignment is coincident with the RCL. When the alignment exceeds 5 degrees the optimum alignment point is 1,500 ft from the RWT on RCL. Where circling approaches are required, apply Order 8260.3 Category A criteria.

(2) Area. The obstacle evaluation area (OEA) begins at the earliest PFAF along-track tolerance (ATT ) and ends at the latest MAP ATT (see figure 4-1).

(a) Length. The IFR final approach segment begins at the PFAF and ends at the MAP. The length should not exceed 10 NM (optimum length is 3 NM). Determine the minimum length using the greater of descent distance, formula 2-7 or 2-8, and table 3-1.

(b) Width.

1 Primary Area. The primary area boundary begins 0.55 NM* each side of the final segment centerline at the earliest PFAF ATT. The width remains constant until the latest PFAF ATT. It then tapers to 0.40 NM* at the latest MAP ATT.

Note: USAF/USA/USCG/USN operating at 90 KIAS: Change 0.55 NM to 0.70 NM and 0.40 NM to 0.50 NM (primary area).

2 Secondary Area. The secondary area boundary is constant, 0.50 NM each side of the primary area. Calculate the primary half-width at any distance from latest MAP ATT using formula 4-1a.

(c) Required Obstacle Clearance. Primary area required obstacle clearance (ROC) is 250 ft. Secondary ROC is 250 ft at the edge of the primary area, tapering uniformly to zero at the outer edge. Calculate secondary ROC using formula 4-1b.

Figure 4-1. LNAV Final Segment Construction.

MAP

Intermediate Segment

0.3 NM

0.3 NM

0.4 NM

0.5 NM

0.5 NM 0.5 NM

0.4 NM 0.4 NM 0.5 NM

0.4 NM

0.5 NM 0.55 NM 0.55 NM 0.5 NM

2-10 NM

Plan View

Cross Sectional

View Primary

d

250’

Centerline

Final Segment

PFAF

Par 3.2.2 adj.

Formula 4-1a. Final Area Half-Width.(WP)

⎛ P − P ⎞ W1 W2 W = P + ⋅ D P W2 ⎜ ⎟ 2 D ⎝ 1 ⎠

Where PW1 = Primary Width, PFAF, (0.55 or 0.7) NM

PW2 = Primary Width, latest MAP ATT, (0.4 or 0.5) NM

D1 = PFAF to MAP distance (NM) D2 = Latest MAP ATT to desired point (NM) WT = Final Total Width (ft) (WP+0.5NM)

PW2+((PW1- PW2)/D1)*D2

Calculator

PW1 PW2

D1 D2

WP (NM)

WP (ft)

WT(ft)

Click here

to calculate

Formula 4-1b. Secondary Area ROC (ROCsecondary).

⎛ d ⎞ primary ROC = ( 250 + adj ) ⋅⎜ 1 − ⎟ sec ondary W ⎝ S ⎠ Where adj = TERPS para 3.2.2 adjustments (ft)

dprimary = distance (perpendicular to C/L from primary area (ft))

WS = Secondary area width (ft)

(250+adj)*(1-dprimary/WS)

Calculator

adj

dprimary

WS ROCsecondary

Click here

to calculate

(3) Descent Gradient/Angle [IVH, PinS , and IVR] ( R ). The descent gradient/angle is measured from the plotted positions of the PFAF at PFAF altitude to the MAP at MDA. Calculate the final segment descent angle using formula 4-2. (Where required, calculate descent gradient using chapter 2, formula 2-10).

Formula 4-2. Final Approach Angle to MAP (DescentAngle).

⎛ r ⎛ r + a ⎞⎞ 180 DescentAngle = atan ⎜ ⋅ ln ⎜ ⎟⎟⋅ ⎝ c ⎝ r + b ⎠⎠ π

Where:

c = PFAF to MAP distance (ft)

a = PFAF altitude MSL b = MDA at MAP MSL

atan(r/c*ln((r+a)/(r+b))*180/π

Calculator

c

a

b

DescentAngle

Click here

to calculate

Note 1: USA maximum descent gradient/angle is 478 ft/NM (4.5 degrees) without a waiver. Descent gradient/angle waivers may be granted up to 800 ft/NM (7.5 degrees).

Note 2: The visual segment descent gradient is considered separately in approaches to VFR heliports or VFR runways.

(4) Descent Gradient/Angle to an IFR Runway or an IFR Heliport. Apply the same descent gradient/angle in chapter 4, paragraph 3a(3) for an IFR approach to an IFR runway, but the distance/elevation calculations begin at the PFAF and end at RWT/TCH elevation (see figure 4-2b). For an IFR approach to an IFR Heliport, the distance/elevation calculations begin at the PFAF and end at HCH (see figure 4-2c). Apply formula 4-3 for descent angle, and chapter 2, formula 2-10 for descent gradient:

Formula 4-3. Descent Angle to Runway

or HCH (DescentAngle).

⎛ r ⎛ r + a ⎞⎞ 180 DescentAngle = atan ⎜ ⋅ ln ⎟⋅ ⎜ ⎟ ⎝ c ⎝ r + b ⎠⎠ π

Where:

c = PFAF to RWT/helipoint distance (ft) a = PFAF Altitude MSL b = TCH/HCH elevation at RWT or HCH

atan(r/c*ln((r+a)/(r+b))*180/π

Calculator

c

a

b

DescentAngle

Click here

to calculate

Figure 4-2a. Descent Angle, PFAF to MAP for IVH/PinS/IVR Procedures.

MAP

VFR Heliport/RWY

Visual/VFR

Segment

MDA(b)

PFAF to MAP Distance in ft (c)

Descent Angle°

Profile View

PFAF

PFAF. Alt (a)

TCH (MSL) (b)

IFR Runway

Figure 4-2b. Descent Angle, PFAF to TCH for IFR Approach to IFR Runway.

PFAF

MAP

Distance in ft (c)

Descent Angle°

PFAF Altitude (a) Profile View

°

Figure 4-2c. Descent Angle, PFAF to HCH for IFR Approach to IFR Heliport.

PFAF

MAP

Distance (c)

IFR Heliport

Visual Segment

Profile View

HCH

Descent Angle°

PFAF Alt (a)

(b)

(5) Stepdown Descent Gradient/Angle. When a stepdown fix is used, measure the descent gradient/angle from the PFAF at the PFAF altitude to the stepdown fix at the minimum fix altitude, then to the MAP at the MDA. For a stabilized approach, provide a constant gradient/angle from the PFAF to the MAP, (may require raising the PFAF altitude). A stepdown fix must be located no closer than 0.6 NM to the PFAF or MAP.

(6) Existing Obstacles Close to the PFAF or Stepdown Fix. If the segment descent gradient/angle is less than 800 ft/NM (7.5 degrees), Order 8260.3B, Volume 1, paragraph 289 may be applied substituting an OIS slope of 3.5:1 vice 7:1. Calculate the OIS Elevation and Minimum fix altitude using formula 4-4.

−

⋅ = + − ⋅ −

x O 3.5 r Z OIS (r a c) e r

⋅ = + + ⋅ −

x O 3.5 r Z MFa (r O c) e r

Where:

a = MSL fix altitude (ft) c = ROC plus adjustments (Order 8260.3, Volume 1, para 3.2.2) Ox = Obstacle along-track distance (ft) from ATT prior to fix (1 NM max)

Oz = MSL obstacle elevation (ft)

MFa = Minimum Fix Altitude (rounded to next higher 100-ft increments)

Formula 4-4. OIS Elevation & Minimum Fix Altitude (OISz & MFa).

ATT

1 NM

Mean Sea Level

a

Stepdown

Fix

Flight Direction

3.5:1

c

OISZ

OZ OX

OISZ=(r+a-c)*e^(-OX/(3.5*r))-r MFa=(r+OZ+c)*e^(OX/(3.5*r))-r

Calculator

a

c

OX

OZ

OISZ

MFa

Click here

to calculate

4. IFR Heliport Visual Segment. The IFR Heliport visual segment connects the MAP to the helipoint. The visual segment OCS starts at the VSRL and extends to the later of a point 250 ft below the MDA or the latest MAP ATT (see figures 4-3 and 4-4).

a. Alignment. The IFR Heliport visual segment connects the MAP to the helipoint. The course change at the MAP from the FAC must not exceed 30 degrees.

Figure 4-3. IFR Heliport Visual Segment OCS

Terminating at Latest MAP Position.

0.3 NM

VSRL

HELIPOINT

0.3 NM

EARLIEST POINT

250’ BELOW MDA

PLOTTED POSITION

LATEST POINT

OCS

VISUAL SEGMENT

DESCENT ANGLE

ATT ALONG TRACK

TOLERANCE

MDA

250’

HALS

DISTANCE FROM MAP TO HELIPOINT

OCS REACHES MDA MINUS 250’ FIRST THEN ENDS AT THE LATEST MAP POSITION

. See Figure 4-6 (Right)

HELIPOINT ELEVATION

HEIGHT ABOVE LANDING ELEVATION

(HAL)

b. Area. The obstacle evaluation area (OEA) begins at the Visual Segment Reference Line (VSRL) and extends toward the MAP as defined below:

(1) Length. The IFR Heliport Visual segment begins at the MAP and ends at the Heliport (see profile figures 4-3 and 4-4).

(2) Width. The visual segment splay begins at the Visual Segment Reference Line (VSRL). It splays from the VSRL endpoints relative to the FAC to the latest FAS primary area width at the latest MAP ATT (see plan view figure 4-6 (right)). Where the OCS surface extends to a point 250 ft below the MDA, the boundary follows the primary area to its end point (see plan view figures 4-4 and 4-6 (left)).

c. Obstacle Clearance Surface. The OCS begins at the VSRL and extends 1.0 degree below the VSDA (see figures 4-3 and 4-4).

Figure 4-4. IFR Heliport Visual Segment OCS

Terminating at an Altitude 250 ft Below MDA.

0.3 NM

VSRL

HELIPOINT

0.3 NM

EARLIEST POINT

250’ BELOW MDA

PLOTTED POSITION

LATEST POINT

OCS

VISUALSEGMENT

DESCENT ANGLE

ATT ALONG TRACK

TOLERANCE

MDA

250’

HALS

DISTANCE FROM MAP TO HELIPOINT

HCH

OCS REACHES THE LATEST MAP POSITION FIRST THEN ENDS AT MDA MINUS 250’ (VSL 250)

See Figure 4-6 (Left)

HELIPOINT ELEVATION

HEIGHT ABOVE LANDING ELEVATION

(HAL)

Figure 4-5. IFR Heliport Visual Segment Area.

0.5 NM 0.5 NM 0.4 NM 0.4 NM

TLOF

0.4 NM

0.4 NM

0.3NM

0.3NM

FINAL COURSE

PRIMARY BOUNDARY

PRIMARY BOUNDARY

SECONDARY BOUNDARY

SECONDARY BOUNDARY

VISUAL SEGMENT OCS

PLAN VIEW

MAP

Figure 4-6. IFR Heliport Visual Segment Area Splays.

VISUAL SEGMENT OCS

PLAN VIEWS EARLIEST EARLIEST MAP MAP LATEST LATEST MAP POSITION MAP POSITION POSITION

0.4 NM 0.4 NM

0.4 NM

0.4 NM

0.3 NM

MAP

PRIMARY PRIMARY POSITION BOUNDARY

0.4 NM 0.4 NM

0.4 NM

0.4 NM

0.3 NM

MAP

BOUNDARY

TLOF TLOF

PRIMARY PRIMARY BOUNDARY BOUNDARY

0.3 NM 0.3 NM See Figure 4-4 See Figure 4-3 OCS EXTENDING OCS EXTENDING TO TO 250 FEET LATEST POINT FIX BELOW MDA (VSL250) CAN BE RECEIVED

d. IFR Heliport with Visual Segment Descent Point (VSDP). A VSDP may be established for straight-in helicopter GPS procedures. Apply the VDP concepts in Order 8260.3, Volume 1, paragraph 253, except use helipoint elevation vice RWT elevation and HCH vice TCH. The recommended descent angle from the VSDP is 6.0 degrees. The maximum angle is 7.5 degrees. Locate the VSDP on the FAC at the point where the visual glide slope indicator (VGSI) on-glide slope beam intersects the MDA. Publish the VSDP as an ATD from the MAP. Do not publish a VSDP where the VSDP falls between the MAP and the helipoint. Where a VGSI is not established, calculate the VSDP to helipoint distance along the FAC using formula 4-5: Note: Where no VSDP has been established, refer to chapter 4, paragraph 4e, then proceed from chapter 4, paragraph 4d(1).

Formula 4-5. VSDP to Heliport Distance (VSDPdist).

d is t =

r M D A r ln r H E H C H V S D P

t a n V S D A

⎛ ⎞ + ⎛ ⎞ ⋅ ⎜ ⎟ ⎜ ⎟ + + ⎝ ⎠ ⎝ ⎠ π ⎛ ⎞ ⋅ ⎜ ⎟ ⎝ 1 8 0 ⎠

Where:

MDA = Final Minimum Descent Altitude (MDA)

HE = Heliport Elevation HCH = Heliport Crossing Height VSDA = descent angle (see formula 4-8)

(r*ln((r+MDA)/(r+HE+HCH))/tan(VSDA*π/180)))

Calculator

MDA

HE

HCH

VSDA

VSDPdist

Click here

to calculate

°

(1) Alignment. The VSDP-based visual segment connects the FAC/VSDP to the helipoint. No course change is allowed at the VSDP.

(2) Area. The obstacle evaluation area (OEA) begins at the VSDP and ends at the helipoint/VSRL (see figure 4-7).

(a) Length. The VSDP-based visual segment begins at the VSDP and ends at the helipoint/VSRL. Determine the VSDP-based visual segment length, VSDP-based descent angle, HAL, and VSRL to a point 250 ft below MDA (VSL250) using the following steps (see figure 4-7).

(b) Width. The VSDP-based visual segment begins at the VSRL. It splays from the VSRL ends at a 10-degree angle relative the FAC until reaching the VSDP.

(3) Obstacle Clearance. No obstacle may penetrate the VSDP-based visual segment OCS (see figure 4-7). Calculate the OCS MSL elevation at any point between the VSRL and the VSDP using formula 4-6. Evaluate obstacles based on the shortest obstacle to surface origin distance (VSRL), measured parallel to the visual segment centerline. Calculate the OCS MSL elevation at a specified obstacle location using formula 4-6.

Formula 4-6. OCS Elevation (OCSelev).

( )

⋅ ⋅ ⎛ ⎞ ⎜ ⎟ ⎝ ⎠ ⋅

π D Tan β

180

r OCS elev r+HE e -r =

Where:

HE = Helipoint elevation MSL

D = Distance obstacle to VSRL(ft) β = OCS Angle

(r+HE)*e^(D*Tan(β*π/180)/r)-r

Calculator

HE

D

β

OCSelev

Click here

to calculate

°

Figure 4-7. IFR Heliport VSDP OCS.

MAP

ATT HELIPORT

0.5 NM

0.3 NM 0.3 NM

0.4 NM 0.4 NM 0.5 NM

PLAN VIEW

FINAL COURSE

75’

75’ VSRL

10°

10° HELIPOINT

MDA

250’ 0.3 NM 0.3 NM

VDP ALONG TRACK DISTANCE

MAP MAP LATEST POSITION

VDP OCS

VSRL

HELIPOINT

MAP EARLIEST POSITION

VGSI BEAM

(4) IFR Heliport HAL, VSDA-based Visual Segment Length (VSL250), and Visual Segment Descent Angle (VSDA) Computations. Calculate HAL, VSRL to a point 250 ft below MDA (VSL250), and VSDA using the following steps (see figure 4-7):

(a) Calculate HAL using formula 4-7:

Formula 4-7. OCS Elevation (HAL).

HAL= MDA-Helipoint Elevation (HE)

MDA-HE

Calculator

MDA

HE

HAL

Click here

to calculate

(b) Calculate VSDA using formula 4-8:

Formula 4-8. Visual Segment Descent Angle (VSDA).

⎛ ⎞ ⎛ ⎞ ⎜ ⎟ ⎜ ⎟ ⎝ ⎠ ⎝ ⎠

+ + = ⋅ ⋅ + r r HAL HCH 180 VSDA atan ln c r HCH π

Where:

c = MAP to Helipoint Distance (ft) HAL = Formula 4-7 output HCH = Heliport Crossing Height

atan(r/c*ln((r+HAL+HCH)/(r+HCH))*180/π

Calculator

c

HAL

HCH

VSDA

Click here

to calculate

(c) Calculate visual segment length from the VSRL to a point 250 ft below MDA (VSL250) using formula 4-9.

Formula 4-9. Visual Segment Length (VSL250).

⎛ ⎞ + ⎛ ⎞ ⋅ ⎜ ⎟ ⎜ ⎟ + ⎝ ⎠ ⎝ ⎠ ⎛ ⎞ − ⋅ ⎜ ⎟ ⎝ ⎠

π V S L = 2 5 0

r a r l n r H E

t a n ( V S D A 1) 1 8 0 Where:

HAL = Formula 4-7 output a = HAL-250 (MSL) HE = Heliport elevation VSDA = Formula 4-8 output

(r*ln((r+a)/(r+HE)))/tan((VSDA-1)*(π/180))

Calculator

HAL

HE

VSDA

VSL250 (ft)

Click here

to calculate

e. No Established VSDP. Where no VSDP has been established, apply the principles of Order 8260.3, Volume 1, paragraph 253. Locate the VSDP on the FAC at the point where the VGSI on-glide-slope beam intersects the MDA. The recommended VSDP on-glide-slope descent gradient/angle is 639 ft/NM (6 degrees). The maximum angle is 7.5 degrees (USA

°

°

maximum descent gradient/angle is 478 ft/NM (4.5 degrees) without a waiver). Where a VGSI facility is installed, the VSDP OCS inclines upward from the VSRL at an angle 1.0 degree below the aiming angle of the on-glide-slope beam. Where no VGSI facility is installed, the VSDP OCS rises 1 degree below the VSDA. Publish the VSDP as an ATD from the MAP. The minimum HCH is 5 ft. The maximum HCH is 20 ft unless approved by Flight Standards. Calculate the VSDP distance (D) from the helipoint using formula 4-10.

Formula 4-10. Distance from Helipoint (D).

⎛ ⎞ + + ⎛ ⎞ ⋅ ⎜ ⎟ ⎜ ⎟ + ⎝ ⎠ ⎝ ⎠ ⎛ ⎞ ⋅ ⎜ ⎟ ⎝ ⎠

D =

r H A L H E r ln r H E

ta n V S D A 1 8 0

π

Where:

HAL = Formula 4-7 output

HE = Heliport elevation VSDA = Formula 4-8 output

(r*ln((r+HAL+HE)/(r+HE)))/tan(VSDA*(π/180))

Calculator

HAL Click here

to calculate

HE

VSDA

D (ft)

5. Special IFR Approach to a VFR Heliport (IVH) (Proceed Visually). The special procedure provides a measure of obstruction protection/ identification along the visual track from a MAP to a specific VFR heliport. The visual segment is based on the premise that the pilot will maintain level flight at the MDA until the helicopter is in a position to initiate a descent to the helipoint. Where obstacles preclude an immediate descent at the MAP to the FATO, establish an ATD fix to provide a descent point to the FATO. When an amended procedure no longer meets the criteria in this paragraph, a PinS procedure applying the criteria in chapter 4, paragraph 7 may be published. Compute the distance for the Remote Altimeter Setting Source (RASS) adjustment for the MDA and stepdown altitudes for the IVH approach procedures from the source to the MAP.

a. Alignment. The IVH visual segment connects the MAP to the helipoint. The optimum IVH visual segment is aligned with the FAC. The course change at the MAP must not exceed 30 degrees.

b. Area.

(1) Length. The IVH visual segment OEA begins at the earliest MAP ATT and ends at the VSRL. The IVH visual segment OEA maximum length is 10,560 ft (2 SM), measured from the MAP plotted position to the helipoint. The optimum MAP/ATD fix to helipoint distance is

°

3,949 ft (0.65 NM). The minimum distance from the MAP/ATD fix to the helipoint is 3,342 ft (0.55 NM).

(2) Width. The IVH visual segment splay begins at the VSRL. It splays from the VSRL endpoints toward the MAP until the visual segment OEA reaches the appropriate construction width [see chapter 4, paragraph 5b(2)(a) or 5b(2)(b)].

(a) Straight Course Construction. Connect the final primary area outer edges (cd) to the VSRL outer edges (ef) (see figure 4-8 ).

Figure 4-8. Straight Visual Segment OEA.

Zoom View

Edges of

VSRL

Farthest corners of

primary area

c

e

e

Helipoint

VSRL

f

f

d

MAP

ATT

Final Course

50’

(b) Turn at the MAP Construction. Refer to figure 4-9, and connect the tangent on the turn side (b) of the MAP nearest the heliport to the VSRL at point (e). This connection extends the turn-side area and identifies whether final secondary areas lie within the visual OEA (The MDA must provide primary ROC within this area). Connect the non-turn-side primary area corner (d) to the VSRL at point (f).

Figure 4-9. Visual Segment with Turn at MAP OEA.

e

e

HELIPOINT

Non-Turn Side Primary Area Corner

VSRL

f

f

d

FINALCOURSE

50’

b

<30°

MAP

ATT 0.3 NM

Tangent to

the ATT

ZOOM VIEW

(3) Visual Segment OIS Evaluation. Apply chapter 4, paragraph 3a for the IFR segment OCA and ROC. Apply chapter 4, paragraph 3a(3) in constructing the descent gradient/angle in the IFR segment.

c. Visual Segment Descent Angle (VSDA). The VSDA is a developer-specified angle extending from a point 5 to 20 ft directly above the helipoint to the MDA. The VSDA must cross the MDA between the helipoint and the MAP. The maximum VSDA is 7.5 degrees, optimum is 6.0 degrees, VSDA angles higher than 7.5 degrees require Flight Standards Service approval. (see figure 4-10).

Figure 4-10. VSDA and OIS.

ATD Helipoint MDA

Profile View

5’

50’

*VSDA 6°

*Vertical OIS VSDA-1°

OIS OIS

Level OIS

Helipoint Elevation

*VSDA = 6°; OIS = 5°

*5°

MDA-(ROC+Adjustments)

VSRL

d. Visual Segment OIS. The OIS begins at the VSRL and extends upward toward the MAP at an angle of (VSDA – 1 degree). The OIS rises to the point it reaches an altitude equal to the MDA minus the ROC and adjustments. Where the MAP is beyond this point, the OIS becomes a level surface to the MAP plotted position. Measure obstacles using the shortest distance to the VSRL. Obstacles should not penetrate the OIS; if they penetrate in the initial evaluation, take one of the following actions, listed in preferential order (see figure 4-11):

(1) Remove or adjust obstacle location and/or height to eliminate the penetration, or

(2) Raise the VSDA to achieve an OIS angle that clears the obstacle, (7.5 degrees maximum without Flight Standards Service approval), or

(3) Identify the obstacle with the greatest penetration. Raise the MDA the penetration amount and round to the next higher 20-ft increment. Initiate action to have the obstacle marked and lighted, if feasible. Depict all obstacles on the approach chart that penetrate the OIS and include in required training.

(4) Raise the HCH to ≤ 20 ft provided the height is consistent with the helicopter’s ability to hover out of ground effect. When this procedure is applied, raise the OIS origin above the helipoint elevation by the amount that the HCH is increased (see figure 4-11).

PROFILE VIEW

Figure 4-11. VSDA and OIS.

HELIPOINT

VSRL

ATD

VSDA ∠

5’-20’

HELIPOINT ELEVATION

VERTICAL

OIS

50’ 50’

MDA

LEVEL OIS

ROC+ADJUSTMENTS

6. Special IFR Approach to A VFR Runway (IVR) (Proceed Visually). This special procedure provides protection/identification along a visual track from the MAP to a specific point on a VFR runway (see figure 4-12 example). This procedure requires the training and equipment contained/specified in an OpSpec or letter of authorization (LOA). This procedure must meet all IVH (Proceed Visually) procedure requirements and the following additional requirements:

a. Location on the runway. The helipoint (aiming point) may be located at any point on a runway centerline, but should be at least a distance of (1.5 * Rotor Diameter) from the end of the usable runway on centerline. The runway is not required to be marked with heliport markings. The visual track from the MAP to the final approach area helipoint must be charted.

b. Alignment. The optimum FAC and visual flight path is aligned with the extended runway centerline, with the MAP at the threshold. The FAC must be aligned within 30 degrees of the extended runway centerline. See paragraph 5 and figures 4-8, 4-9 and 4-12 for OEA construction examples.

c. Day operations. An ‘acceptable’ visual segment day flight evaluation for flyability and OIS obstacle penetration must be completed.

d. Night operations. An ‘acceptable’ visual segment night flight evaluation for flyability must be completed. This evaluation must confirm the runway lighting system is visible from the MAP.

e. Helipoint Location. The runway final approach area about the heliport must be clearly viewable from the MAP.

Figure 4-12. IFR to a VFR Runway.

e

e

HELIPOINT

Non-Turn Side Primary Area Corner

f

f

d

FINALCOURSE

50’

b

<30°

MAP

ATT 0.3 NM

Tangent to

the ATT

Runway ZOOM VIEW

7. PinS Approach (Proceed VFR). The VFR segment on a PinS (Proceed VFR) approach procedure provides a measure of obstacle protection/identification to allow a safe transition from IFR to VFR flight. The area is not intended to support IFR descent.

Apply Order 8260.3, Volume 1, chapter 11 pertaining to PinS approach criteria, except no requirement exists for a MAP to be located beyond 2,600 ft of the helipoint. A PinS (Proceed VFR) procedure may be developed to a heliport, multiple heliports, or a geographical area not associated with a specific heliport. Refer to chapter 2, paragraph 3 to determine whether procedures are ‘Specials.’ Compute the distance for the Remote Altimeter Setting Source (RASS) adjustment for the MDA and stepdown altitudes for the PinS approach procedures from the source to the MAP.

a. Alignment. The PinS visual segment is a 5,280 ft-radius arc segment centered at the FAC and the latest MAP ATT intersection.

b. Area. The PinS OEA is a 5,280 ft-radius arc segment centered at the FAC and the latest MAP ATT intersection. The arc segment is laterally bounded by 20 degree splay lines (relative the FAC-extended), originating at the FAS secondary boundaries and the latest MAP ATT (see figure 4-13).

c. Length. A 5,280 ft radius as described above.

d. PinS visual segment OIS (see chapter 4, paragraph 7e). This surface must not be penetrated except when a ‘special approach procedure’ MDA, not providing obstacle clearance in this area, is mandatory for mission completion. Obstacles that penetrate the special procedure surface must be charted and included in the required training (AAOs are not charted).

Figure 4-13. PinS (Proceed VFR) VFR Transition Area Obstacle Evaluation (OEA).

Obstacle Evaluation

Area

5,280’

ATT

FAS

MAP

20°

20°

FAC

e. Obstacle Clearance in the PinS VFR Segment. Add 250 ft of ROC (minus adjustments) to the highest obstacle/terrain within the VFR area and (round to the next higher 20-ft increment). The final MDA is the higher of the MDAs calculated for the final and VFR segments. This does not apply to special approaches (see chapter 4, paragraph 7d).

f. Visibility. The minimum final segment visibility is ¾ SM for a height above surface (HAS) of 800 ft and below. Where a HAS exceeds 800 ft, the MINIMUM visibility is 1.0 SM.

8. IFR to an IFR Runway.

a. Configuration and Alignment. The MAP location should provide the best compromise of lowest visibility and VSDA. Except where the alignment is to the RWT, the mandatory MAP location is at the FAC and RCL intersection. Where the alignment is to the RCL, the optimum MAP location is at the RWT, with optional MAP location along the FAC between the PFAF and the RWT.

b. Area. The final OEA begins at the earliest PFAF ATT and ends at the latest MAP ATT, RWT, or a point abeam the RWT, whichever is farthest. Apply chapter 4, paragraph 3a criteria for the IFR segment OEA and ROC (see figure 4-1).

c. Descent Gradient/Angle. Calculate the FAS descent angle from the PFAF altitude at the plotted position of the PFAF to the TCH at RWT. Apply chapter 4, paragraph 3a(4).

d. Visual Segment. Apply Order 8260.3, Volume 1, paragraph 3.3.2.d. Establish a 40 ± 5 ft TCH for runways where no VGSI is installed. Where a VGSI is installed, a final descent gradient and VSDA may be established to coincide with the established gradients/angles for angles of 3.0 angles or more. If the descent gradient/angle cannot be published coincident (within ± 0.20 degrees) and TCH values within 3 ft of the published VGSI glide slope angle, publish a note on the chart.

e. Visibility. See chapter 7, paragraph 1b. Apply Order 8260.3, Volume 1, paragraph 1127. Where obstacles penetrate Order 8260.3, Volume 1 paragraph 3.3.2.d. surfaces, add the chart note: Visibility Reduction by helicopters NA. See Order 8260.19, paragraph 854(i)(3).

Note: When a special procedure has a GPA greater than 5.7 degrees and a TCH higher than 45 ft, Order 8260.3, Volume 1, paragraph 1127 may be applied. Table 25 application is required.

9. WAAS LP Criteria. The WAAS LP criteria apply to the final approach only. For all other segments apply GPS criteria except where noted for a turn at the PFAF, and missed approach constructions that are different. This implementation of WAAS does not include a glidepath function for these procedures. Criteria in this chapter provide a narrower OEA in the IFR FAS and OIS in the visual segment. The segment lengths and descent rate/gradients are the same as chapter 4, paragraph 3. The intermediate segment begins with the same width at the GPS intermediate fix (IF), reference chapter 3, paragraph 1b, tailored to the beginning WAAS FAS width, reference chapter 4, paragraph 9d at the PFAF. Apply chapter 4, paragraph 5 through 7 to design approaches in the visual/visual flight rule (VFR) segments, and apply chapter 4, paragraphs 8 and 9 for the IFR FAS OEA and ROC. Apply an OIS, reference chapter 4, paragraph 5d, with the reduced width, reference chapter 4, paragraph 8d. Apply chapter 4, paragraph 5 for the analysis of the VFR area of a Point in Space (PinS) (Proceed VFR) approach.

Figure 4-17 depicts the basic configuration for determining the Flight Path Alignment Point (FPAP) and fictitious helipoint (FHP) coordinates. Locate the FHP 2,600 ft from the MAP. The FPAP is a point defined by the World Geodetic System 1984 (WGS-84) latitude, longitude, and is located 9,023 ft from the FHP.

a. Minimums. Apply chapter 7.

b. Use The Following Steps for WAAS LP Procedure Construction:

Step 1: Determine the FAS course alignment, MAP, FHP, and FPAP coordinates.

Step 2: Calculate the distance (ft) from the FHP to the PFAF (DPFAF) using formula 4-11. Calculate the primary and secondary area widths at any distance from FHP to the earliest point the PFAF can be received using formulas 4-11 and 4-13 (see figure 4-14).

Formula 4-11. LP PFAF (DPFAF).

elev PFAF

r alt ln r r FHP HCH D

tan 180

⎛ ⎞ + ⋅ ⎜ ⎟ + + ⎝ ⎠ = π ⎛ ⎞ ⎜θ ⋅ ⎟ ⎝ ⎠

Where:

alt = minimum intermediate segment altitude FHPelev = FHP MSL elevation HCH = HCH value

θ = glidepath angle

(ln((r+alt)/(r+FHPelev+HCH))*r)/tan(θ*π/180)

Calculator

FHPelev

HCH

θ

alt

DPFAF (ft)

Click here

to calculate

Step 3: After constructing the IFR final trapezoid area, analyze the FAS by determining the controlling obstacle within the IFR final segment by applying the ROC in chapter 4, paragraph 9b and determining the minimum descent altitude (MDA).

Step 4: When constructing an IFR to a VFR heliport procedure (IVH, Proceed Visually), or an IFR approach to a VFR runway procedure (IVR, proceed visualy), apply chapter 4 criteria for the visual segment, but construct the narrower OIS in accordance with chapter 4, paragraph 9g.

Step 5: When constructing a PinS (Proceed VFR) approach, apply chapter 4 criteria for the VFR segment and adjust the MDA of the IFR segment after an analysis of the VFR segment if required.

Step 6: Construct the missed approach using chapter 5.

c. Determine FAS Course Alignment, FPAP and FHP Coordinates. The FAS course determines the positional relationship between the FPAP and the FHP. Calculate the FPAP latitude and longitude coordinates using the MAP as a starting point after determining the procedure final approach course (FAC). Use the direct program and extend the FAS course as an azimuth at a distance of 2,600 ft from the MAP to determine the FHP coordinates. Extend this course 9,023 ft beyond the FHP to calculate the FPAP coordinates (see figure 4-14 and table 4-1).

°

Figure 4-14. FPAP and FHP Coordinates.

PFAF FAS Course

Extension of the

FAS Course

MAP FHP FPAP

Optimum Segment Length

3 NM Segment 2,600’ 9,023’

Table 4-1. FPAP Information.

FPAP Distance from

FHP ± Splay ± Width

9,023 ft 2.0° 350 ft

(106.75 m)*

Length Offset

0

*Round result to the nearest 0.25 m.

d. Area. The FAS OEA begins at the earliest PFAF position and ends at the MAP latest ATT (see figure 4-16). The PFAF and MAP ATT is ±40 m. Apply 250 ft of ROC in the primary area. The secondary area ROC is 250 ft at the primary boundary tapering uniformly to zero at the outer edge. The beginning primary area width nearest the FHP is 867.79 ft, and the secondary areas are 468.60 ft (see figures 4-15b and 4-16). Calculate the primary and secondary widths at any point between FHP and PFAF using formulas 4-12 (primary) and 4-13 (secondary).

(1) Length. The standard IFR final segment length PFAF to MAP is 3 NM but is also determined by descent gradient. The minimum length is 2 NM and the maximum length is 50,000 ft. (see figure 4-15a).

Figure 4-15a. WAAS LP Final Segment.

EXAMPLE

(P)FAF See figure 4-15b

50,000’

200’

Primary

Secondary

Secondary

Cross Section At Cross Section At 200’ from RWT OCS 50,200’ from RWT

OCS

ASBL

3,812.40’

4,195.70’ 4,195.70’

8,008.1’ 8,008.1’

3,812.40’ 300’ 300’

700’ 700’

Figure 4-15b. WAAS LP Final Segment Construction.

MAP

PFAF

300’

200’ from FHP

ATT 40m

1,749.99’

1,749.99’

1,749.99’

1,749.99’

2,143.10’

2,143.10’

2,143.10’

2,143.10’

ATT

FHP

300’ 700’700’

2,600’ from Fictitious Helipoint (FHP)

Primary

Area Secondary

Area

See figure 4-16 for PinS approach width

PLAN VIEW

Cross Section View 3.43 NM from Helipoint

3 NM

3.43 NM

3,893.10’

3,893.10’

Secondary

Area

Secondary

Area

3,893.10’

3,893.10’

MDA

250’ ROC

Par. 3.2.2 Adjustments

+- 40m

+-

p

Figure 4-16. OCS Beginning Width, IFR to VFR Heliport

and Copter PinS FAS at 2,600 ft from FHP.

MAP

468.60’ 468.60’ 867.79’

ATT’ 40m

1,336.39’ 1,336.39’

867.79’

Primary Primary Secondary

2,600’ from FHP

Latest MAP ATT

Secondary

+

-

(2) The primary area width (DP) each side of FAC at its origin (2,600 ft from FHP) is 867.79 ft. The primary area expands uniformly to 3,495.70 ft from FAC at a point 50,200 ft from FHP. From 50,200 ft outward, the OEA is linear (boundaries parallel the centerline). The OEA begins at the earliest PFAF ATT and ends 2,600 ft from the FHP (MAP latest ATT). Calculate primary area half-width at any point in final using formula 4-12 (see figures 4-15a, 4-15b, and 4-16).

Calculate the perpendicular distance (ft) Dp from FAC to the primary area boundary at any distance (dFHP) using formula 4-12:

Formula 4-12. ½ Width of Primary (D ).

D =1/2 Primary Area Width (ft) = 0.0699139 (d - 200) + 700 P FHP dFHP = Distance (ft) from FHP, along course

0.0699139*(dFHP-200)+700

Calculator

dFHP

DP (ft)

Click here

to calculate

(3) The perpendicular distance from FAC to outer secondary boundary (Ds) is 1,336.39 ft at the origin, and expands uniformly to 7,008.1 ft at 50,200 ft from the FHP (see figures 4-15a, 4-15b, and 4-16). Calculate DS (ft) using formula 4-13.

Formula 4-13. Perpendicular Distance (Ds).

S FHP D = Secondary Boundary Dist. (ft) = 0.140162 (d - 200) + 1000

Where:

DS = Course to Outer Secondary Distance (ft) dFHP= Distance from FHP (ft), along course

0.140162*(dFHP – 200) + 1000

Calculator

dFHP

DS (ft)

Click here

to calculate

e. Required Obstacle Clearance (ROC). Primary ROC is 250 ft. The MDA can be no lower than the controlling obstacle height adjusted for obstacle accuracy tolerance (see Order 8260.19, appendix 2) plus the ROC value plus adjustments rounded to the next higher 20 ft-increment. Calculate secondary area ROC using formula 4-14.

Formula 4-14. Secondary Area ROC (ROCsecondary).

⎛ dprimary ⎞ ROC secondary = (250+adj) ⋅ 1 − ⎜⎜ ⎟⎟ W ⎝ s ⎠

Where:

adj = TERPS para 3.2.2 adjustments dprimary = perpendicular distance (ft) from primary area edge

WS = Secondary Area Width (ft)

(250+adj)*(1-dprimary/Ws)

Calculator

adj

dprimary (ft)

Ws (ft)

ROCsecondary

Click here

to calculate

f. FAS Descent Angle/Gradient. Apply chapter 4, paragraphs 3a(4) and 3a(5).

g. IFR Approach to a VFR Heliport (IVH) or IFR to a VFR Runway (IVR). Apply chapter 4, paragraphs 5 through 7 and the criteria in this chapter for the IFR final segment OEA. Construct the IFR FAS by applying chapter 4, paragraph 9. The OIS width is like the IFR final segment primary area width at the latest point the MAP can be received (± 867.79 ft) then narrows to the VSRL width (see figure 4-17).

Figure 4-17. Straight and Turn at the MAP OIS.

MAP

c c d

f

f

f

f e

e e VSRL

Helipoint Helipoint

VSRL

e

d

FAS FAS

MAP

Primary

Latest point fix can be received

FHP

FHP

<30°

Primary Area

Width

Visual Segment

OIS

Visual Segment

OIS

Primary Area

Width

Heliport Straight-In

PLAN VIEW

Heliport

Offset

Secondary

Primary

<10,560’

50’ 50’

h. PinS Approach. Apply chapter 4, paragraph 9 to determine a preliminary MDA based on the FAS OEA. Apply chapter 4, paragraph 7 and 7e for the VFR segment analysis. The final MDA may require adjustment based on the VFR segment for a public procedure.

Chapter 5. Missed Approach

1. General.

a. Missed Approach (MA) Construction.

(1) Speed. Apply 70 KIAS for civil procedures (see chapter 2, paragraph 1) and 90 KIAS for military. Apply wind values (see chapter 2, formula 2-3b) and bank angles (see chapter 2, table 2-4).

(2) Optimum Flight Path. The missed approach segment ends at a holding point designated by a missed approach holding fix (MAHF). Optimum routing is straight ahead to a direct entry into holding at the MAHF. If the MA routing terminates at a “T” IAF, optimum MA holding pattern alignment is with the initial inbound course, with either a teardrop or direct entry into holding (see figure 5-1a).

Note: USA: Develop and annotate an alternate RNAV(GPS) MA procedure when requested.

b. Obstacle Clearance Standard. Calculate the nominal OCS slope (MAOCSSLOPE) associated with a given missed approach climb gradient using chapter 2, formula 2-15. See chapter 2, paragraph 17 for Missed Approach Conventions.

c. Missed Approach Section 1 (MAS-1). Section 1 begins at earliest MAP along-track tolerance (ATT) and extends to the start-of-climb (SOC), or the point where the aircraft is projected to cross 400 ft above airport/heliport elevation, whichever is the greatest distance from MAP. See figure 5-1b for MA segment point and line designations. Figure 5-2 depicts the Section 1/Section 2 (partial), OCS plan and profile view beginning at an altitude of MDA minus 100 ft plus adjustments (see chapter 4 for greater final segment detail).

(1) Length.

(a) Flat Surface Length (FSL).

1 LNAV. Section 1 flat surface begins at CD (0.3 NM prior to the MAP) and extends (distance FSL feet) to JK.

2 LP. Section 1 flat surface begins at CD [40 meters prior to the MAP] and extends (distance FSL feet) to JK.

Step 1: Calculate the FSL value using formula 5-1. Use chapter 4, final segment formulas 4-1a, (LNAV primary and total), and 4-12 (LP primary), and 4-13 (LP Secondary distance) to determine MAS starting widths.

Formula 5-1. Flat Surface Length (FSL).

( )

( )

⎛ ⎞ ⎛ ⎞ ⋅ + − ⋅ ⎜ ⎟ ⎜ ⎟ = ⋅ ⋅ + + ⋅ ⎜ ⎟ ⎜⎜ ⎟⎟ − ⋅ ⎝ ⎠ ⎝ ⎠

i KIAS 2.628

1852 171233 288 15 0.00198 MDA 0.3048 FSL 8 V 10 2 ATT 3600 288 0.00198 MDA

8*(1852/0.3048/3600)*((VKIAS*(171233*((288+15)-0.00198*MDA)^0.5)/ (288-0.00198*MDA)^2.628)+10)+2*ATT

Calculator

VKIAS MDA

ATT (ft)

FSL(ft)

Click here

to calculate

Note: FSL time is 3 seconds reaction, and 5 seconds delay.

(2) Section 1 end location (AB).

(a) MDA ≥ 400 ft above airport/heliport elevation. Locate AB coincident with JK.

1852 (b) MDA < 400 ft above airport/heliport elevation. Locate AB at feet (0.3048 CG) ⋅ beyond JK for each foot of altitude needed to reach 400 ft above airport/heliport/surface elevation. The surface between JK and AB is a rising slope commensurate with the standard rate of climb (400 ft/NM). Find the appropriate CG-related slope using chapter 2, formula 2-15.

(c) Required/assigned turning altitude > 400 ft above airport/heliport elevation. Locate AB and apply the surface described in chapter 5, paragraph 1c(2)(b) until reaching the assigned turning altitude.

(3) Width. LNAV and LP.

Continue reading ↓ 120 of 260 passages shown