Radar Vectors
FAA Order Cancelled Issued Dec 7, 2016 AJR-0 136 pages Copy saved Nov 18, 2026

Order 7930.2R Notices to Airmen (NOTAM)

This order prescribes direction used to format and distribute information regarding unanticipated or temporary changes to services, components of, or hazards in, the National Airspace System (NAS). The Notices to Airmen (NOTAM) system does not advertise published or charted data and information. Originators of airmen information are expected to inform the National Flight Data Center (NFDC) in sufficient time before the effective dates of changes to permit publishing of aeronautical data on the various charts or in the appropriate publications. When time does not allow for publication of a change or an outage and if the subject matter meets NOTAM criteria, issue a NOTAM until published.

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

Text read by OCR from a scanned file (17 of 136 pages). Check the original, as some words may be misread.

Order 7930.2R Notices to Airmen (NOTAM)

Distribution: ZAT-721, ZAT-464 Initiated By: AJR-0 Vice President, System Operations Services

O r der 79

30.2R National Policy

Effective Date: January 5, 2017

SUBJ: Notices to Airmen (NOTAM)

This Order prescribes direction used to format and distribute information regarding unanticipated or temporary changes to services, components of, or hazards in, the National Airspace System (NAS). Controllers are required to be familiar with the provisions of this order that pertain to their operational responsibilities. The Notices to Airmen (NOTAM) system does not advertise data already published or charted.

Order 7930.2R Notices to Airmen (NOTAM) › Explanation of Changes

Explanation of Changes E of Chg−1

Notices to Airmen

(NOTAM)

Explanation of Changes

Effective: January 5, 2017

1−1−7 2c Deleted the reference to Policy and Software

1−1−8 The effective date of the 7930.2R is January 5, 2017.

1−1−9 Added the Technical Operations order, 6750.24 to the references.

1−3−1 Added AIS responsibilities from the Flight Standards order, 6750.19, to here

1−3−2 Changed the title to “Technical Operations”.

Divided the duties into section a. for the Operations Control Center (OCC) and the Service Operations Center (SOSC) and section b. for Flight Inspection Services which previously was in section 1−3−3 of the 7930.2Q.

1−3−3 Added the Service Area as a NOTAM Originator and renumbered the rest of the paragraphs.

1−3−4 Added A and B responsibilities from the AFS order.

1−3−7 Moved section describing Non−Federal Facilities from 3−2−4 to this section.

1−4−3 Edited to move all examples into Appendix A.

1−4−6 h. Added a definition of the Federal NOTAM System. Renumbered the rest of them.

NEW – Added definition of Visual Navigation Aid

m. Added more to the term Military from chapter 8.

r. Pointer NOTAM – added the phrase “additional aeronautical information”

NEW – Added definition of Radio Navigation Aid

2−1−1 and throughout

Changed U.S. NOTAM System to NOTAM system.

2−1−4 Combined sections a. and b. to 2−1−4 then moved the rest to Appendix E.

2−1−8 d Changed name from Aeronautical Information Management to Aeronautical Information Services.

3−1−1 Moved “Tie−In Stations” paragraph to Appendix E. Renumbered the rest of paragraphs.

Paragraphs d. and e. were added to explain how NOTAMs exceeding 20 lines are auto rejected and that all auto−reject messages are not stored in the NOTAM master file.

3−1−3 Moved “NOTAM LOG” to Appendix E

3−1−4 “FDC Presidential” is now 3−1−2 and section b. through section e. have been moved to Appendix E

3−2−3 “Passing NOTAM” moved to Appendix E

3−2−4 “Non−Federal” added to 1−3−7

3−3−1 Added clarification about the term “service” always being spelled out.

Explanation of Changes E of Chg−2

3−3−4 Added leading zero to (RWY 03/21)

3−3−5 e. Added description for use of L, R, and C in NOTAMs.

Added leading zeros to the examples.

3−3−5 f. Changed the example to only show the runway identification – removed the condition of the NOTAM

3−3−6 a. 1. Changed the examples to only show the taxiway identification (removed the condition), deleted the NOTE, and moved the full examples to Appendix A.

3−3−6 a. 3. Removed the condition from the helipad example.

3−3−6 b. Clarified the definition by removing reference to the condition and added to policy how ALL is defined; also amended the first example to show TWY ALL. Moved the remaining examples to Appendix A.

3−3−6 c. 1. Removed the condition from the examples. Moved the last example to policy under 3−3−6 c. 3.

3−3−6 c. 2. Changed the condition of the first example to WIP.

3−3−6 c. 3. Added to policy how to indicate the intersection of two taxiways and included an example.

3−3−7 a/b Removed the conditions from the examples.

3−3−8 Added BARRICADED with a definition and LGTD AND BARRICADED as standard NO- TAM phrases.

4−1−1 Moved “Accepting NOTAM D Information” to Appendix E; renumbered and combined paragraphs into 1.

4−2−1 Added a graphical depiction of NOTAM Sentence Structure to 4−2−1, and policy of using the sentence structure.

4−2−1 a. 14 (b) Deleted the (See paragraph 4−4−3), from this section.

4−2−1 a. 14 (e) Changed “OPEN” to “OPN”, the ICAO contraction

4−3 Moved to Appendix E – Miscellaneous Functions. Renumbered rest of paragraphs/sections

4−4 Renamed Section 3; former paragraph 4−4−3 a. moved to Appendix E USNS/AISR Functions. Renumbered rest of paragraphs

4−5−1 Section 5 Moved to Appendix E Computer Functions

5−1−2 b. and throughout

Moved examples to Appendix A, Examples.

5−1−3 Added Sentence Structure Graphic

Shortened initial phrase for work flow

Added policy of using AP, Heliport or Seaplane base for standardization

5−1−3 b. Moved some of the verbiage from a. to b.

Moved the table to Appendix A, Examples.

5−1−4 Background: Section 5−1−4 is restructured due to the Takeoff and Landing Performance Assessment (TALPA) workgroup, which was formed to address the safety of operations on wet and contaminated runways, as well as improvements to the assessment and reporting of airport conditions. The cornerstone recommendation produced by the work is the Runway Condition Assessment Matrix (RCAM) and its associated elements used to promote the use

Explanation of Changes E of Chg−3

of standardized terminology by all parties involved in the process of determining, describing, and distributing the runway surface conditions and their effects on takeoff and landing decisions.

Added Sentence Structure Graphic

PATCHY is no longer used

THN is eliminated. Actual measurement is used

RUTS is no longer a condition of the contaminated surface. It is part of the Safety Area. Removed from FICON.

No partial Reporting (S 2000ft)

No standalone MU NOTAMs for runways – removed the list of runway friction devices

Rubber is deleted from reportable contaminant list

Removed Pilot Reported feature

All reference to MU and friction measuring equipment is deleted.

If the whole runway is treated (plowed, swept) the treatment is not included.

Differences between RWY, TWY and APRON

Description of Runway Condition Code (RCC) and the Runway Condition Assessment Matrix (RCAM) Added these tables to the order

Format of a FICON NOTAM

FICON

RwyCC

Condition – describes what is included as the “condition”

Action – describes the actions taken to treat the surfaces

Methods (plow, swept, deiced, sanded)

Types of ridges (snowbanks, berms, etc.)

Remainder – if different from the full width.

Braking Action

Observation Time

Conditions Not Monitored

Start/End time

Rubber as described on runways and taxiways.

5−1−5 Added a Sentence Structure graphic and generic NOTAM example

a. 4. Added the verbiage for INDEX A ARFF outage.

5−1−5 d. Deleted the explanation, the example will show the format

5−1−6 Added a Sentence Structure graphic, and generic NOTAM example

5−1−6 d. Changed the format and numbering of sentence structure from d−j to c. 1−7

5−2−1 Added a Sentence Structure graphic, and generic NOTAM example – Moved all examples to Appendix A, Examples

Explanation of Changes E of Chg−4

5−2−1 b. Made the “Lead on lead off” note into policy.

5−2−2 Added a Sentence Structure graphic, and generic NOTAM example

9.(a) Added Out of Service as a condition for non−FCC.

5−3−6 Reworded paragraph a for clarity

5−3−7 Added Sentence Structure graphic and generic NOTAM example

5−3−7 c. Added Sentence Structure graphic and generic NOTAM example

5−3−8 a. 1. Moved Note 1 to Appendix A, Examples, Note 2 to USNS Appendix and Note 3 becomes Note 1.

5−4−3 Added a Sentence Structure graphic. Made the note about frequencies into policy.

5−5−1 Added a Sentence Structure graphic and generic NOTAM example.

6−1−1 Added a Sentence Structure graphic and generic NOTAM example.

6−1−3 d. Changed wording to remove “as depicted below” since examples are in Appendix A

6−1−5 b. Was deleted (already shown in TBL 6−1−1) c & d become b & c.

6−1−5 c. Kept the headers of activities requiring authorization. Moved the rest to Appendix A.

7−1−3 Added a Sentence Structure graphic and generic NOTAM example. Information contained in 8260.19 was moved here.

7−1−5 b. Made the note with the FSS phone number into POLICY

7−2−2 /7−2−3 Moved to Appendix E Computer Functions

8−1−1 Moved to Appendix D Miscellaneous Functions

8−3−1 to 8−3−3 Moved to Appendix E Computer Functions

8−3−4 Included this section in 1−4−6, Military NOTAMs

Chapter 9 Renumbered to become Chapter 8

9−1−2 b and 9−1−3 Moved to Appendix E Computer Functions

9−2−1 b. Moved to Appendix E Computer Functions

Order 7930.2R Notices to Airmen (NOTAM) › Comments/Corrections

Comments/Corrections

Comments or corrections concerning this publication may be submitted on this form and submitted electronically to: 9−AJV−8−HQ−[email protected]

Notice to Editor

The following comments/corrections are submitted concerning the information contained in: Paragraph number Title Page Dated …

Name Street City State Zip

Comments/Corrections

Order 7930.2R Notices to Airmen (NOTAM) › Table of Contents

Section 4. Terms of Reference

Table of Contents

Chapter 1. General

Section 1. Introduction

Paragraph Page 1-1-1. PURPOSE … 1-1-1 1-1-2. AUDIENCE … 1-1-1 1-1-3. WHERE TO FIND THIS ORDER … 1-1-1 1-1-4. CANCELLATION … 1-1-1 1-1-5. EXPLANATION OF CHANGES … 1-1-1 1-1-6. DISTRIBUTION … 1-1-1 1-1-7. RECOMMENDATIONS FOR PROCEDURAL CHANGES … 1-1-1 1-1-8. EFFECTIVE DATE … 1-1-2 1-1-9. RELATED PUBLICATIONS … 1-1-2

Section 2. Scope

1-2-1. PURPOSE … 1-2-1 1-2-2. PROCEDURAL APPLICATIONS … 1-2-2 1-2-3. AVOIDANCE OF DUPLICATION … 1-2-2

Section 3. Accountable Organizations

1-3-1. AIR TRAFFIC ORGANIZATION (ATO) … 1-3-1 1-3-2. TECHNICAL OPERATIONS … 1-3-2 1-3-3. FLIGHT STANDARD SERVICES … 1-3-2 1-3-4. OFFICE OF AIRPORT SAFETY AND STANDARDS … 1-3-3 1-3-5. AIRPORT MANAGEMENT … 1-3-3 1-3-6. NON-FEDERAL FACILITIES … 1-3-3 1-3-7. DEPARTMENT OF DEFENSE AIRFIELD MANAGEMENT … 1-3-3

1-4-1. WORD USE IN THIS ORDER … 1-4-1 1-4-2. NOTES … 1-4-1 1-4-3. EXAMPLES … 1-4-1 1-4-4. REFERENCES … 1-4-1 1-4-5. MANUAL CHANGES … 1-4-1 1-4-6. DEFINITIONS … 1-4-1

Chapter 2. Aeronautical Information Services

Section 1. Aeronautical Information System

2-1-1. GENERAL … 2-1-1 2-1-2. DISSEMINATION OF AIRMEN INFORMATION … 2-1-1 2-1-3. PUBLICATION CRITERIA … 2-1-1 2-1-4. NOTICES TO AIRMEN PUBLICATION … 2-1-2 2-1-5. CHART/PUBLICATION ERRORS OR OMISSIONS … 2-1-2 2-1-6. FORWARDING DATA … 2-1-2 2-1-7. ADDRESSING CORRESPONDENCE … 2-1-2

Table of Contents i

Section 2. Preparing NOTAMs for Dissemination

Paragraph Page 2-1-8. NFDC ORGANIZATION … 2-1-3 2-1-9. THE NATIONAL FLIGHT DATA DIGEST (NFDD) … 2-1-3 2-1-10. COMPUTER PRINTOUTS … 2-1-3

Chapter 3. General Operating Procedures

Section 1. General

3-1-1. NOTAM RESPONSIBILITIES … 3-1-1 3-1-2. FDC PRESIDENTIAL, SPECIAL SECURITY INSTRUCTIONS, OR EMERGENCY AIR TRAFFIC RULES TFRs … 3-1-1

Section 2. Coordination

3-2-1. COORDINATION WITH OTHER FACILITIES … 3-2-1 3-2-2. FILING NOTAM INFORMATION WITH FSSs … 3-2-1

Section 3. Use of Terms

3-3-1. USE OF CONTRACTIONS AND ABBREVIATIONS … 3-3-1 3-3-2. EXPRESSION OF TIME IN THE NOTAM SYSTEM … 3-3-1 3-3-3. UNITS OF MEASUREMENT … 3-3-1 3-3-4. USE OF VIRGULE (/) … 3-3-2 3-3-5. RUNWAY IDENTIFICATION … 3-3-2 3-3-6. TAXIWAY IDENTIFICATION … 3-3-2 3-3-7. APRON IDENTIFICATION … 3-3-3 3-3-8. STANDARD NOTAM PHRASES … 3-3-3 3-3-9. CARDINAL DIRECTIONS … 3-3-4

Chapter 4. NOTAM D Procedures

Section 1. General

4-1-1. NATIONAL NOTAM OFFICE RELATIONSHIPS … 4-1-1

4-2-1. NOTAM COMPOSITION … 4-2-1 4-2-2. NOTAM ACCOUNTABILITY … 4-2-3

Section 3. Canceling/Extending NOTAMs

4-3-1. EXTENDING NOTAM VALIDITY … 4-3-1 4-3-2. CANCELLATION OF NOTAMs … 4-3-1 4-3-3. CANCELING PUBLISHED NOTAM DATA … 4-3-1

Chapter 5. NOTAM Criteria

Section 1. Movement Area NOTAMs

5-1-1. ORIGINATORS OF AERODROME NOTAMs … 5-1-1 5-1-2. HANDLING REPORTED AERODROME CONDITIONS … 5-1-1 5-1-3. MOVEMENT AREA INFORMATION … 5-1-1 5-1-4. FIELD CONDITIONS (FICON) REPORTING … 5-1-3

Table of Contents ii

Section 1. Transmitting FDC NOTAM Data

Paragraph Page 5-1-5. AERODROME FACILITIES … 5-1-9 5-1-6. WORK IN PROGRESS … 5-1-9

Section 2. Lighting Aid and Obstruction NOTAMs

5-2-1. LIGHTING AIDS … 5-2-1 5-2-2. OBSTACLES … 5-2-2

Section 3. NAVAID NOTAMs

5-3-1. GENERAL … 5-3-1 5-3-2. REPORTING NAVAID MALFUNCTIONS … 5-3-1 5-3-3. UNPROGRAMMED EXTENDED SHUTDOWNS … 5-3-1 5-3-4. NAVAID MAINTENANCE SHUTDOWNS … 5-3-1 5-3-5. UNMONITORED NAVAIDs … 5-3-1 5-3-6. INSTRUMENT LANDING SYSTEM STATUS … 5-3-1 5-3-7. NAVAID CONDITIONS … 5-3-2 5-3-8. SATELLITE BASED SYSTEMS … 5-3-4 5-3-9. HOURS OF OPERATION … 5-3-4

Section 4. Communications Outlets NOTAMs

5-4-1. GENERAL … 5-4-1 5-4-2. REPORTING COMMUNICATIONS OUTLET MALFUNCTIONS … 5-4-1 5-4-3. COMMUNICATION OUTLET CONDITIONS … 5-4-1

Section 5. Services NOTAMs

5-5-1. GENERAL … 5-5-1 5-5-2. CHANGES TO PUBLISHED SERVICES … 5-5-1 5-5-3. HOURS OF OPERATION … 5-5-1 5-5-4. WEATHER AND WEATHER REPORTING EQUIPMENT … 5-5-2 5-5-5. MICROBURST/WINDSHEAR DETECTION SYSTEM … 5-5-3 5-5-6. RADAR SERVICES … 5-5-3

Chapter 6. Airspace NOTAMs

Section 1. Airspace

Paragraph Page 6-1-1. AIRSPACE NOTAM FORMAT … 6-1-1 6-1-2. SPECIAL ACTIVITY AIRSPACE (SAA) … 6-1-1 6-1-3. AIRSPACE AND ALTITUDE RESERVATIONS … 6-1-2 6-1-4. SPECIAL AERIAL REFUELING … 6-1-2 6-1-5. OTHER AIRSPACE NOTAMS … 6-1-3 6-1-6. SURFACE AREA AIRSPACE … 6-1-4

Chapter 7. FDC NOTAMs

7-1-1. GENERAL … 7-1-1 7-1-2. TEMPORARY OR PERMANENT FDC NOTAMS … 7-1-1

Table of Contents iii

Section 2. Procedures For Canadian NOTAMs

Paragraph Page 7-1-3. INSTRUMENT IFR FLIGHT PROCEDURES … 7-1-2 7-1-4. HIGH BAROMETRIC PRESSURE WARNING … 7-1-6 7-1-5. TEMPORARY FLIGHT RESTRICTIONS … 7-1-6 7-1-6. AIR DEFENSE EMERGENCY … 7-1-7 7-1-7. SPECIAL DATA … 7-1-7 7-1-8. LASER LIGHT ACTIVITY … 7-1-7

Section 2. Cancellation/Expiration

7-2-1. FDC NOTAM EXPIRATION/CANCELLATION … 7-2-1

Chapter 8. International NOTAMs

Section 1. General Procedures

Paragraph Page 8-1-1. INTERNATIONAL NOTAMs … 8-1-1 8-1-2. INTERNATIONAL NOTAM DATA FORMAT … 8-1-1

8-2-1. REQUEST FOR CANADIAN NOTAMs FROM THE CANADIAN NOTAM SYSTEM … 8-2-1

Appendices

APPENDIX A. EXAMPLES … Appendix A-1 APPENDIX B. INTERNATIONAL NOTAM (Q) CODES … Appendix B-1 APPENDIX C. ICAO DIFFERENCE FOR THE UNITED STATES … Appendix C-1 APPENDIX D. MISCELLANEOUS FUNCTIONS … Appendix D-1 APPENDIX E. COMPUTER FUNCTIONS … Appendix E-1 APPENDIX F. NATIONAL WEATHER SERVICE (NWS) RADIOSONDE/

UNMANNED FREE BALLOON FLIGHTS … Appendix F-1

Index

Index … I-1

Table of Contents iv

Chapter 1. General › Section 1. Introduction

Chapter 1. General

Section 1. Introduction

1−1−1. PURPOSE

This order prescribes direction used to format and distribute information regarding unanticipated or temporary changes to services, components of, or hazards in, the National Airspace System (NAS). The Notices to Airmen (NOTAM) system does not duplicate data already published or charted. Originators of airmen information are expected to inform the National Flight Data Center (NFDC) in sufficient time before the effective dates of changes to permit publishing of aeronautical data on the various charts or in the appropriate publications. When time does not allow for publication of a change or an outage and if the subject matter meets NOTAM criteria, issue a NOTAM until published.

1−1−2. AUDIENCE

The primary audience for this order is any office responsible for originating NOTAMs. The secondary audience is those who use aeronautical information.

1−1−3. WHERE TO FIND THIS ORDER

This order is available on the Federal Aviation Administration (FAA) website at http://faa.gov/air_traffic/ publications and http://employees.faa.gov/tools_resources/orders_notices/.

1−1−4. CANCELLATION

FAA Order JO 7930.2Q, Notices to Airmen (NOTAM) dated December 18, 2015 is canceled.

1−1−5. EXPLANATION OF CHANGES

The significant changes to the basic order will be published and included in the Explanation of Change page(s). It is advisable to retain the page(s) throughout the duration of the basic order. If further information is desired, direct questions through the appropriate facility/service area staff to System Operations Services, Flight Services, Safety and Operations Policy Group.

1−1−6. DISTRIBUTION

This order is distributed to selected offices in Washington headquarters, service area offices, the William J. Hughes Technical Center, the Mike Monroney Aeronautical Center, and air traffic operations field offices and facilities.

1−1−7. RECOMMENDATION FOR PROCEDURAL CHANGES

a. The contents of this order will be periodically reviewed and updated, as required by National Airspace Data Interchange Network (NADIN), General Notices (GENOTs), and order changes. Changes/orders are published on the publications cycle.

b. Any changes to this order must be submitted to the VP, Mission Support Services, attn.: ATC Procedures Office, AJV−11:

1. Personnel should submit recommended changes in procedures to facility management.

2. Recommendations from other sources should be submitted through appropriate FAA, military, or industry/user channels.

Introduction 1−1−1

1−1−8. EFFECTIVE DATE

This order is effective January 5, 2017.

1−1−9. RELATED PUBLICATIONS

Military units issue NOTAMs pertaining to their bases and airspace based on the guidelines set forth in Air Force Instruction Interservice Publication 11-208/AR 95-10/OPNAVINST 3721.20, DoD Notice to Airmen (NOTAM) System.

FAA Order 5010.4, Airport Data and Information Management

JO 7110.10, Flight Services

JO 7210.3, Facility Operations and Administration

JO 7400.2, Procedures for Handling Airspace Matters

JO 7400.8, Special Use Airspace

Technical Operations

− 6000.15, General Maintenance Handbook for NAS Facilities

− 8200.1, U.S. Standard Flight Inspection Manual.

− 6750.24, Instrument Landing System and Ancillary Electronic Component Configuration and Performance Requirements

Flight Standards

− 8260.19, Flight Procedures and Airspace

FAA Order 5010.4, Airport Safety Data Program

14 CFR Parts

− 77, Safe, Efficient Use, and Preservation of the Navigable Airspace

− 139, Certification of Airports

− 157, Notice of Construction, Alteration, Activation and Deactivation of Airports

− 171, Non-Federal Navigation Facilities

Advisory Circular (AC) 150/5200−28, Notices to Airmen (NOTAMs)for Airport Operators

AC 150/5200−30, Airport Field Condition Assessments and Winter Operations Safety

AC 150/5300−18B, General Guidance and Specifications for Submission of Aeronautical Surveys to NGS: Field Data Collection and Geographic Information System (GIS) Standards

ICAO Annex 15

Introduction 1−1−2

Chapter 1. General › Section 2. Scope

Section 2. Scope

1−2−1. PURPOSE

Authorized personnel assigned to facilities that collect, originate, and/or disseminate NOTAMs must be familiar with the provisions of this order that pertain to their operational responsibilities.

a. The United States NOTAM Office (USNOF) is the authority ensuring NOTAM formats. To ensure NOTAMs are issued consistent with NOTAM policy, submitters must comply with USNOF personnel directions.

b. All NOTAMs will be processed, stored, and distributed by the NOTAM System (NS).

c. NOTAMs must have one of the following keywords as the first part of the text. A keyword is used to make it easier to sort and locate the specific data needed: RWY, TWY, APRON, AD, OBST, NAV, COM, SVC, AIRSPACE, ODP, SID, STAR, CHART, DATA, IAP, VFP, ROUTE, SPECIAL or SECURITY.

NOTE− Examples of keywords (RWY, TWY, APRON, AD, OBST, NAV, COM, SVC) are shown in chapter 5; AIRSPACE in chapter 6; (IAP, ODP, SID, STAR, ROUTE, and SPECIAL) relating to instrument flight procedures in chapter 7.

1. RWY (Runway). Keyword used to describe a temporary change or hazard associated with landing and takeoff surfaces to include runway lighting, markings, signage, and other airport services or attributes associated with a specific runway.

2. TWY (Taxiway). Keyword used to describe a temporary change or hazard associated with a taxiway, taxiway lighting, markings, helipads, signage and other attributes associated with a specific taxiway.

3. APRON (Apron/Ramp). Keyword used to describe a temporary change or hazard associated with an apron, ramp, or taxilane, lighting, markings, helipad, signage and other attributes associated with a specific apron.

4. AD (Aerodrome). Keyword used to describe a temporary change or hazard or potential hazard on or within 5 statute miles of an airport, heliport, or maneuvering area that is not associated with a specific movement area surface. Such hazards may include, (but are not limited to), aerodrome closures, lighting not associated with a specific movement area surface, aerodrome services (fuel, customs, ARFF), helicopter platforms, wildlife hazards, and meteorological equipment (wind indicators) or services.

5. OBST (Obstructions). Keyword used to describe a temporary change or hazard caused by a moored balloon, kite, tower, crane, stack, obstruction, obstruction lighting outage, obstruction status, or telecommunication tower light outage.

6. NAV (Navigation Aids). Keyword used to describe a temporary change or hazard caused by the changes in the status of ground-based radio navigational aids and Global Navigation Satellite Systems (GNSS) (except for area navigation (RNAV) approach anomalies).

7. COM (Communications). Keyword used to describe a temporary change or hazard caused by communication outlet commissioning, decommissioning, outage, unavailability, and air-to-ground frequencies.

8. SVC (Services). Keyword used to describe a temporary change or hazard associated with change in service levels, such as operating hours, air traffic management services, or airport services.

9. AIRSPACE (Airspace). Keyword used to describe an airspace restriction or activity warning which impacts, restricts, or precludes use of airspace.

10. ODP (Obstacle Departure Procedure). Keyword used when a NOTAM applies to a textual or graphic obstacle departure procedure.

11. SID (Standard Instrument Departure). Keyword used when a NOTAM applies to a published standard instrument departure.

Scope 1−2−1

12. STAR (Standard Terminal Arrival). Keyword used when a NOTAM applies to a published standard terminal arrival.

13. CHART (Chart). Keyword used to describe a U.S. Government chart correction, followed by name of chart and word “CORRECT” that becomes effective before the next publication cycle.

14. DATA (Data). Keyword used to describe a temporary change or hazard associated with a data set change followed by the name of the data set to be changed; for example U.S. DOD DAFIF, DACS, or NFD.

15. IAP (Instrument Approach Procedure). Keyword used when a NOTAM applies to a published instrument approach procedure.

16. VFP (Visual Flight Procedure). Keyword used when a NOTAM applies to visual flight procedures such as Charted Visual Flight Procedure and RNAV Visual Flight Procedure.

17. ROUTE (Route). Keyword used to describe a temporary change or hazard or change associated with published ATS routes and related information.

18. SPECIAL (Special). Keyword used when a NOTAM applies to a special instrument flight procedure.

19. SECURITY (Security). Keyword used for Department of State advisories, Special Federal Aviation Regulations (SFARs), advisories of national emergency, national security actions, special security instructions, air defense identification zone (ADIZ) procedures.

NOTE− Keyword SECURITY is not used for NOTAMs that describe a defined restricted area or TFR. Such NOTAMs would use keyword AIRSPACE.

d. (U) – Unverified. (U) is used preceding a keyword as described in paragraph 5-1-2.

e. The United States Department of Defense (DOD) will append the keywords IAP, SPECIAL, ODP, SID, and STAR with “U. S. DOD” to indicate that a published procedure is for military use only (not for civil use). For example, STAR U. S. DOD, SID U. S. DOD, IAP U. S. DOD.

1−2−2. PROCEDURAL APPLICATIONS

Apply the procedures in this order except when other procedures are contained in a Letter of Agreement or other appropriate FAA documents, provided they only supplement this order and that any standards they specify are not less than those in this order. FAA Order JO 7210.3, Facility Operation and Administration, contains administrative procedures for developing and executing those letters and documents.

1−2−3. AVOIDANCE OF DUPLICATION

Before issuing a NOTAM on any NOTAM criteria data, check all appropriate charts and publications to assure the information does not duplicate the published data. Do not issue a NOTAM on information that duplicates published data unless a NOTAM is required by a Certificate of Waiver or Authorization from Title 14, Code of Federal Regulations (CFR) issued by the FAA.

1−2−2 Scope

Chapter 1. General › Section 3. Accountable Organizations

Section 3. Accountable Organizations

1−3−1. AIR TRAFFIC ORGANIZATION (ATO)

a. All air traffic employees, regardless of position, must immediately report any situation or condition considered hazardous to flight to an air traffic facility for appropriate action.

NOTE− Situations that present an immediate hazard should be reported to the air traffic control (ATC) facility most concerned. Other situations should be reported on a first priority basis to the flight service station or appropriate accountable organization.

b. Air traffic personnel must accept all aeronautical information regardless of source or subject matter, provided the occurrence is no more than three days in the future. Obtain the name, title (if appropriate), address, and telephone number of the person furnishing the information and forward all data to the appropriate FSS for NOTAM issuance, if appropriate.

NOTE− Forwarding the NOTAM data to the tie-in FSS does not relieve the forwarding facility from the responsibility of coordinating the information with other affected ATC facilities.

c. The party that originates the NOTAM on behalf of the accountable organization is responsible for the accuracy, origination, and cancellation of the NOTAM. FSS personnel receiving NOTAM information that requires action by another FSS must forward the information to that FSS for appropriate action.

d. The certified source is responsible for the correct classification and format of the NOTAM and for ensuring that facilities affected by the NOTAM are aware of the new NOTAM.

e. FSS specialists are responsible for issuing NOTAMs that are not covered in any example in FAA Order JO 7930.2. If, after consulting with your management, a format cannot be determined, have management contact USNOF for assistance.

f. System Operations Services, Flight Services, has the responsibility to ensure that data submitted complies with the policies, criteria, and formats contained in this order. This responsibility is delegated to the Safety and Operations Policy Group.

g. Service Areas originate NOTAMs for certain FDC criteria, including Laser activities and Temporary Flight Restrictions that are issued by the USNOF through NS.

h. Mission Support Services, Aeronautical Information Services (AIS) is responsible for originating Flight Data Center (FDC) NOTAMs for revisions to standard instrument approach procedures (SIAP), air traffic service (ATS) routes, textual and graphic departure procedures (both ODPs and SIDs), and special instrument flight procedures. AIS may originate NOTAMs regarding navigational aid (NAVAID) restrictions in accordance with FAA Order 8200.1, United States Standard Flight Inspection Manual. AIS is responsible for:

1. Formulating Instrument Flight Procedures (IFP) and ATS route NOTAMs for procedures for which they have responsibility and forwarding them for transmittal.

2. Formulating FDC PERM NOTAMs used to correct aeronautical chart printing and compilation errors related to all U.S. Government aeronautical charting products and forwarding them for transmittal.

3. Designating an office to develop specific internal guidance for NOTAM preparation, quality control, transmittal, cancellation, and follow−up actions for FDC NOTAMs issued by AIS. This guidance must be developed in concert with the NFDC and the USNOF. As a minimum, the guidance must include the following:

(a) Procedures to ensure that the airport manager at the affected location is notified whenever possible.

Accountable Organizations 1−3−1

(b) Procedures to ensure all NOTAMs are reviewed for accuracy, completeness, content, etc. prior to submission.

(c) Procedures to ensure the NFDC is provided information copy of all NOTAMs and cancellations.

(d) Procedures to ensure non−FAA service providers are provided an information copy of all NOTAMs and cancellations at those locations non−FAA service providers are allowed. This will ensure non−FAA service providers are aware of the condition requiring the NOTAM.

4. The NFDC is responsible for ensuring a hard/electronic copy of each PERM NOTAM is stored with the current amendment and maintained in the procedures archive file.

i. Mission Support Services, Airspace Services, is responsible for the development of policy guidance regarding standard terminal arrival routes (STAR). STAR NOTAMs are originated by the Air Route Traffic Control Center (ARTCC) (See paragraph 7-1-4f).

j. USNOF executes the operational compliance function. When operational personnel of the USNOF determine that NOTAM information submitted is not in compliance with the criteria or procedures as prescribed, they must call this to the attention of the transmitting party. USNOF will forward unresolved issues to the Flight Services Program Operations for clarification and further action. The USNOF is responsible for operating the NOTAM system. USNOF originates NOTAMs, as needed. (See paragraph 4-1-2, National NOTAM Office Relationships for more detail)

NOTE− NOTAM office phone numbers: (888) 876-6826; (540) 422-4262. FAX number is (540) 422-4298.

1−3−2. TECHNICAL OPERATIONS

a. Operations Control Center (OCC) and Service Operations Center (SOC).

The Technical Operations Services, Operations Center manager, or representative, is responsible for:

1. Originating and canceling NOTAM information for shutdown, restoration, or any condition that affects the operations of NAVAIDs, frequencies, or other electronic aids that affect safety of flight. This includes forwarding data of programmed changes in the NAS, such as frequency changes, commissioning/ decommissioning, etc.

2. Coordinating with appropriate air traffic facilities prior to shutdown or changes that affect safety of flight.

3. When possible, approval should be obtained sufficiently in advance of the proposed shutdown time to allow dissemination of a NOTAM at least 5 hours before a shutdown will occur. A routine maintenance shutdown request must not be denied because of an inability to issue a NOTAM 5 hours in advance of the shutdown.

b. Flight Inspection Services

Flight Inspection Services under FAA Order 8200.1, United States Standard Flight Inspection Manual, initiate NOTAMs regarding radio and lighting NAVAID restrictions. Facility classification based on flight inspection results is the responsibility of the flight inspector.

REFERENCE− FAA Order 5010.4, Airport Safety Data Program, and 14 CFR Parts 139 and 157

1−3−3. FLIGHT STANDARDS SERVICE

a. Flight Technologies and Procedures Division, AFS−400, is responsible for development of policy guidance and procedures for the origination, tracking, and cancellation of NOTAMs relating to instrument flight procedures. This policy applies to the following: SIAPs, ATS routes, textual and graphic ODPs, SIDs, and special instrument flight procedures (see paragraph 1−3−1 for procedures addressing STAR NOTAMs). AFS−400 is responsible for oversight of non−FAA service providers authorized to maintain SIAP and/or special instrument flight procedures. Maintenance includes issuance of FDC NOTAMs.

1−3−2 Accountable Organizations

b. Flight Procedure Implementation & Oversight Branch, AFS−460, is responsible for coordinating non−FAA service provider NOTAM authority and access to the FAA NOTAM system with ATO Mission Support Services, Aeronautical Information Services. The branch is also responsible for ensuring that specific guidance for NOTAM preparation, quality control, transmittal, cancellation, and follow−up actions are developed for NOTAMs applicable to public and Special IFPs developed by non−FAA service provider and not under the purview of AIS. As a minimum, the guidance must ensure the non−FAA service provider NOTAM originators include the following:

1. Procedures to ensure that all affected ARTCC facilities are provided notification of NOTAMs at the time of submission. The NOTAM issuing authority must also attempt to notify the airport manager at the affected location whenever possible.

2. Procedures to ensure all NOTAMs are reviewed for accuracy, completeness, content, etc. prior to submission.

3. Procedures to ensure the NFDC is provided an information copy of all NOTAMs and cancellations.

4. Procedures to ensure that AIS is aware of those locations where non−FAA service provider procedure development is allowed.

5. Procedures to ensure that AIS is provided an information copy of all NOTAMs and cancellations issued by other non−FAA service providers. This will ensure FAA procedure developers are aware of the condition requiring the NOTAM.

c. AFS−460 serves as the approval authority for requests that temporary NOTAMs be allowed to extend beyond the 224−day timeframe.

1−3−4. OFFICE OF AIRPORT SAFETY AND STANDARDS

Though not an accountable organization, the Office of Airport Safety and Standards is responsible for enforcing the airport management responsibilities as outlined in the Code of Federal Regulations. (CFR).

1−3−5. AIRPORT MANAGEMENT

Specific airport management responsibilities are outlined in 14 CFR Parts 139 and 157. Airport managers are required to abide by applicable provisions of these and pertinent regulations regardless of application of any procedure in this order.

1−3−6. NON−FEDERAL FACILITIES

a. NOTAMs on non−Federal facilities covered by FAAO 6700.20, Non−Federal Navigation Aids, Air Traffic Control Facilities, and Automated Weather Systems are distributed through the FAA NOTAM system.

REFERENCE− 14 CFR Part 171 outlines owner/operation responsibilities. b. NOTAMs on non−Federal facilities that are not part of the NAS are not distributed in the FAA NOTAM system. FSSs receiving data on these facilities must notify Aeronautical Information Services.

1−3−7. DEPARTMENT OF DEFENSE AIRFIELD MANAGEMENT

Specific military airport management responsibilities are outlined in Air Force Instruction Interservice Publication 11−208/AR 95−10/OPNAVINST 3721.20, DoD Notice to Airmen (NOTAM) System.

Accountable Organizations 1−3−3

Chapter 1. General › Section 4. Terms of Reference

Section 4. Terms of Reference

1−4−1. WORD USE IN THIS ORDER

As used in this order:

a. “Must” means a procedure is mandatory.

b. “Should” means a procedure is recommended.

c. “May” or “need not” means a procedure is optional.

d. “Must not” means a procedure is prohibited.

e. Singular words include the plural.

f. Plural words include the singular.

g. Miles means nautical miles unless otherwise stated.

h. Feet means mean sea level unless otherwise stated.

i. Time is shown in Universal Coordinated Time (UTC) unless otherwise stated, as in the body of Temporary Flight Restrictions.

1−4−2. NOTES

Statements of fact of an introductory or explanatory nature and relating to the use of directive material have been identified and worded as NOTE.

1−4−3. EXAMPLES

An illustration which serves to explain subject material is identified as an EXAMPLE which represents the format discussed in each section and is used as an aid to support policy. Not all components of the NAS will be illustrated with an example. The examples throughout Appendix A contain the keyword and the subject of the NOTAM. All other data is assumed from the NOTAM sentence structure and are eliminated from examples.

1−4−4. REFERENCES

When another paragraph of this order is referenced in the text, the referenced paragraph number will be printed out in full. When a paragraph is referenced in a Reference subparagraph, the referenced paragraph’s title, followed by its number, will be printed in regular type. When other documents and directives are referenced in a Reference subparagraph, the document/directive and the paragraph number will be printed in regular type. All references to other FAA orders reflect the current edition of the order.

1−4−5. MANUAL CHANGES

When revised, reprinted, or additional pages are issued, they will be marked as follows:

a. Each revised or additional page will show the change number and effective date of the change.

b. Vertical lines in the margin of the text will mark the location of substantive procedural, operational, or policy changes; that is, when material which affects the performance of duty is added, revised, or deleted.

1−4−6. DEFINITIONS

The terms below as used in this order are defined in this section.

Terms of Reference 1−4−1

a. Accountable Organization. The accountable organization is responsible for accurately reporting the condition considered to be a hazard or potential hazard to flight operations. Reporting the condition must be accomplished by ensuring that procedures are developed to establish NOTAM origination and coordination responsibilities.

b. Accountability Location. This is the location identifier of the location in the NOTAM computer that keeps track of the NOTAM numbering.

c. Aeronautical Information. Any information concerning the establishment, condition, or change in any component (facility, service, or procedure of, or hazard) of the NAS. This information is published and/or disseminated by means of aeronautical charts, publications, and/or NOTAMs.

d. Airport Operating Certificate. A certificate issued by the FAA, pursuant to 14 CFR Part 139, to airports serving or expected to serve scheduled air carrier operations in aircraft with a seating capacity of more than thirty passengers. These airports are maintained and operated in accordance with an Airport Certification Manual (ACM) prepared by airport management and approved by the FAA.

e. Certified Airport. An airport certificated under 14 CFR Part 139. These airports are so indicated in the airport/facility directory.

f. Certified Source. The party who enters/submits a NOTAM to the NOTAM System (NS) using an approved direct entry tool or interface

g. Distribution. Forwarding of NOTAM information from the NS to NADIN.

h. Fix/Radial/Distance (F/R/D). Is a VOR identifier followed by 3-digit degrees magnetic and minimum of a 3-digit distance in nautical miles with no spaces between characters (AML360020.1 would be 360-degree radial, 20.1NM from AML VOR/DME).

i. Flight Data Center (FDC) NOTAM. The classification of NOTAMs containing flight information that is normally regulatory in nature including, but not limited to, changes to IFR charts, procedures, and airspace usage. FDC NOTAM numbers are assigned consecutively by the NS, beginning with 0001 each year. The year of issuance and the serial number are separated by a forward slash; for example, 5/1323.

j. International NOTAM. The classification of NOTAMs received from other counties and stored in the NS. These NOTAMs are numbered consecutively by accountability, location, and series beginning with S0001 each year, where S stands for a generic series a country may have. The NOTAM number and year of issuance are separated by a forward slash; for example, S0211/15, S0002/15.

k. Location Identifier. Used to designate an affected airport, air route traffic control center (ARTCC), or facility.

l. Military NOTAM. The classification of NOTAMs issued by the U.S. Air Force, Army, Marine Corps, Navy, and Coast Guard against navigational aids and airports. Military units issue NOTAMs pertaining to their bases and airspace based on the guidelines set forth in Air Force Instruction Interservice Publication 11−208/AR 95−10/OPNAVINST 3721.20, DoD Notice to Airmen (NOTAM) System. These NOTAMs are numbered consecutively by accountability, location, and series beginning with S0001 each year, where S stands for a generic series the military may have. The NOTAM number and year of issuance are separated by a forward slash; for example, S0211/15, S0002/15.

m. Movement Area. The term Movement Area as used for the purpose of NOTAMs, include Runways, Taxiways, Ramps, Aprons, helipads, heliports and maneuvering areas.

n. NAVAID. Any visual or electronic device airborne or on the surface which provides point−to−point guidance information or position data to aircraft in flight.

o. NOTAM D. The classification of NOTAMs containing information concerning the establishment, condition, or change in any aeronautical facility, en route navigational aids, services, procedures, hazards and civil public-use airports listed in the AFD. NOTAM Ds are numbered consecutively each month by the NS

Terms of Reference 1−4−2

starting with 001 for each accountability, for example: DAY 01/001 would be the first NOTAM in the month of January for Dayton Accountable Location.

p. NOTAM Originator. The party (airport, Tech Ops, AIS/Service Provider, FSS, etc.) who submits a NOTAM to the NS using an approved interface and is accountable for the NOTAM coordination.

q. NOTAM System. A safety−critical system that collects, maintains and distributes NOTAMs for the aviation community.

r. Out of Service. When a piece of equipment, a NAVAID, a facility or a service is not operational, certified (if required) and immediately “available” for air traffic or public use. Used on facilities in which the FAA maintains the equipment.

s. Pointer NOTAM. NOTAM D issued to point to additional aeronautical information. The keyword in the pointer NOTAM must match the keyword in the original NOTAM. For example, a pointer NOTAM at a specific airport is used to highlight or “point out” an FDC NOTAM.

t. Prior Permission Required (PPR) means prior permission required to have full operational use of a runway, taxiway, apron, or airport facility/service. Means of communication to the airport can be telephone and/or radio.

u. Radio Navigation Aid. As used in this policy, the word radio is added further describe those navigation aids such as ILS, LOC, VOR or other NAVAID that is used in assisting the pilot with approaches, departures, and enroute operations.

v. Supplement (Alaska, Pacific, U.S.).

1. Alaska. This chart supplement is a joint civil-military flight information publication designed for use with other flight information publications, en route charts, Alaska Terminal publication, USAF TACAN charts covering Alaska and portions of southwestern and northwestern Canada, World Aeronautical Charts, and sectional aeronautical charts. The Supplement contains an airport/facility directory of all airports (including certificated (14 CFR Part 139) airports shown on en route charts and those required by appropriate agencies), communications data, navigational facilities, special notices, and procedures applicable to the area of chart coverage.

2. Pacific. This chart supplement is a civil flight information publication, designed for use with flight information publications, en route charts and the sectional aeronautical chart covering the State of Hawaii and that area of Pacific served by U.S. facilities. The Supplement contains an airport/facility directory of all airports (including certificated (14 CFR Part 139) airports open to the public and those requested by appropriate agencies), communications data, navigational facilities, special notices and procedures applicable to the Pacific area.

3. U.S. The chart supplement (formerly known as Airport/Facility Directory) for the contiguous United States.

w. Taxilanes. Designed for low speed and precise taxiing. Taxilanes usually provide access (to and) from taxiways (usually an apron taxiway) to (and from) aircraft parking positions and other terminal areas.

x. Tie-In Station. A flight service station designated to provide prescribed services for civil, military, national and international facilities; for example, NOTAM purposes and flight information messages.

y. Unusable. The NAVAID is not available for operational use because it does not meet flight inspection requirements (may provide potentially unsafe or erroneous signals, or signals of unknown quality).

z. Virgule (/). For US NOTAM purposes - a diagonal symbol used to separate similar alternatives.

aa. Visual Navigation Aid. As used in this policy, the word visual is added to further describe those navigation aids such as PAPI, ALS, VASI, etc., or any other lighting aid that is used in assisting the pilot with approaches or departures.

Terms of Reference 1−4−3

ab. WMSCR – Weather Message Switching Center Replacement is one of the FAA’s gateway for the receipt and distribution of weather within the National Airspace System (NAS).

Terms of Reference 1−4−4

Chapter 2. Aeronautical Information Services › Section 1. Aeronautical Information System

Chapter 2. Aeronautical Information Services

Section 1. Aeronautical Information System

2−1−1. GENERAL

The system for disseminating aeronautical information is made up of two subsystems, the Aeronautical Information System (AIS) and the NOTAM System. The AIS consists of charts and publications. The NOTAM system is discussed in later paragraphs.

2−1−2. DISSEMINATION OF AIRMEN INFORMATION

Airmen information is disseminated by the following methods:

a. Aeronautical charts depicting permanent baseline data:

1. IFR Charts:

(a) Enroute High Altitude Conterminous U.S.

(b) Enroute Low Altitude Conterminous U.S.

(c) Alaska Charts.

(d) Pacific Charts.

2. U.S. Terminal Procedures:

(a) Departure Procedures

(b) Standard Terminal Arrivals (STARs).

(c) Standard Instrument Approach Procedures (SIAPs).

3. VFR Charts:

(a) Sectional Aeronautical Charts.

(b) Terminal Area Charts

(c) World Aeronautical Charts

b. Flight information publications outlining baseline data:

1. Notices to Airmen Publication (NTAP).

2. U.S. Chart Supplement

3. Pacific Chart Supplement.

4. Alaska Supplement.

5. Alaska Terminal.

6. Aeronautical Information Manual (AIM).

2−1−3. PUBLICATION CRITERIA

The following conditions or categories of information should be forwarded to the National Flight Data Center (NFDC) for inclusion in the flight information publications and charts. Time critical delays, corrections, or changes to previously published data that cannot be republished before occurrence must be issued as a NOTAM, providing they meet the criteria set forth in this order.

Aeronautical Information System 2−1−1

a. NAVAIDs. Commissioning, decommissioning, restrictions, frequency changes, changes in monitoring status and monitoring facility used in the National Airspace System (NAS). NAVAID outage NOTAMs must remain active until the NAVAID is returned to service or decommissioned.

b. Commissioning, decommissioning, changes in hours of operation of FAA air traffic control facilities.

c. Surface areas/airspace. Changes in hours of operations.

d. Remote Communication Outlets and Remote Communication Air Ground. Commissioning, decommissioning, changes in voice control or monitoring facility.

e. Weather reporting stations. Commissioning, decommissioning, failure, nonavailability or unreliable operations.

f. Public airports. Commissioning, decommissioning, openings, closings, and abandonment.

g. Airport Rescue Fire Fighting (ARFF) capability. Restrictions to air carrier operations.

h. Changes to runway identifiers, dimensions, threshold placements, and surface compositions.

i. NAS lighting systems. Commissioning, decommissioning, outages, change in classification or operation.

2−1−4. NOTICES TO AIRMEN PUBLICATION

NTAP is published by Mission Support Services, Standards and Procedures Support, every 28 days. See Apendix D for further information.

2−1−5. CHART/PUBLICATION ERRORS OR OMISSIONS

a. Managers must review each edition of the Notices to Airmen Publication, the Airport/Facility directory, and other publications and charts to ensure that all required data is included and correct. Inform NFDC promptly of errors or omissions in any publication or chart. Notification of errors in the NTAP parts three and four should be sent to ATC Products and Publications.

b. Managers must review all current NOTAMs issued by their facility on a quarterly basis for currency.

c. When NOTAMs are published, or more than 30 days old, contact the accountable organization for possible cancellation.

2−1−6. FORWARDING DATA

a. When notice is received of a temporary condition which is expected to be corrected before information can be published, issue a NOTAM if it meets criteria.

b. NOTAM or aeronautical information concerning an extended (more than 30 days) shutdown or closure affecting components of the NAS must be forwarded in advance of the occurrence to the NFDC. NFDC must publish data received in accordance with existing policies, criteria, and publication cutoff deadlines. The schedule of publication cutoff dates is contained in the AFD.

c. When time does not permit notification to NFDC by mail, forward the data via administrative message, FAX, or contact the appropriate NFDC section by telephone during administrative hours.

d. Information received by NFDC for publication that meets publication criteria and will be current on the effective date of the next available AFD publication or aeronautical chart will be published.

2−1−7. ADDRESSING CORRESPONDENCE

Federal Aviation Administration Aeronautical Information Services 1575 I Street, NW. Room 9404 Washington, D.C. 20005

2−1−2 Aeronautical Information System

2−1−8. NFDC ORGANIZATION

The NFDC is divided into the following sections. Refer questions and data to: Toll Free: (866) 295−8236 or website: https://nfdc.faa.gov.

a. Airports and NAVAIDs

b. Procedures and Airspace

2−1−9. THE NATIONAL FLIGHT DATA DIGEST (NFDD)

The NFDD is used to transmit data from NFDC to chart and publication producers. It may be used to update records. However, it must not be used as a basis to cancel NOTAMs.

2−1−10. COMPUTER PRINTOUTS

Computer printouts listing all navigational aids and public use civil landing areas by flight plan area may be obtained from Aeronautical Information Services.

Aeronautical Information System 2−1−3

Chapter 3. General Operating Procedures › Section 1. General

Chapter 3. General Operating Procedures

Section 1. General

3−1−1. NOTAM RESPONSIBILITIES

a. The party that enters the NOTAM data is responsible for classifying, formatting, canceling, and informing the controlling facility and other facilities/offices affected by the aid, service, or hazard contained in the new NOTAM. Flight Service Stations are exempt from the requirement to inform the controlling facility when an alternate means of coordination is approved by the Flight Service Safety and Operations Group, AJR-B1 or coordination responsibilities have been spelled out in waivers and authorizations in order for the activity to take place.

b. Any office which receives information is responsible for the accuracy, currency, and validity of the NOTAM. When an office receives information that is outside their area of responsibility, they will inform the accountable organization.

c. FSSs must accept all aeronautical information. Information obtained from other than authorized personnel must be confirmed before issuance. NOTAM data received from state inspectors or state contracted inspectors must be confirmed by airport managers or appropriate authority before issuance of NOTAMs except in case of data that presents an immediate hazard to aircraft operations. If a NOTAM is issued without confirmation, advise the airport manager as soon as possible. In case of conflict between airport management and the named state airport inspector, contact FAA regional airports personnel for resolution. Conditions requiring a NOTAM should be coordinated with the appropriate air traffic facilities.

REFERENCE− FAA Order JO 7930.2, Para 5−1−2 , Handling Reported Aerodrome Conditions

d. A Domestic NOTAM will auto reject if it is over 20 lines. Ensure the NOTAM meets Aeronautical Fixed Telecommunication Network capability prior to originating NOTAM.

e. When a NOTAM is rejected, it is not distributed. It will not be stored in the NOTAM master file, and it will not be available by request−reply. Error messages are not stored in the master file.

f. ARTCCs are responsible for forwarding FDC and special activity airspace (SAA) NOTAM information to the affected terminal facilities.

REFERENCE− FAA Order JO 7930.2, Para 6−1−2 Special Activity Airspace (SAA)

3−1−2. FDC PRESIDENTIAL, SPECIAL SECURITY INSTRUCTIONS, OR EMERGENCY AIR TRAFFIC RULES TFRs

See appendix D for further information.

a. The NS must send NOTAMs referencing Title 14 CFR, Part 91, Section 139, Emergency Air Traffic Rules; Section 141, Flight Restrictions in the Proximity of the Presidential and Other Parties; Part 99, Section 7, Special Security Instructions; and any revisions, modifications, or cancellations, directly to all flight service stations via NADIN using the flight service group address of “KXXXAFSS.”

General 3−1−1

Chapter 3. General Operating Procedures › Section 2. Coordination

Section 2. Coordination

3−2−1. COORDINATION WITH OTHER FACILITIES

When a shutdown or an outage/closure of a component of the NAS will affect another facility’s operation, the facility serving as the approval/ controlling authority must coordinate with other facilities concerned.

3−2−2. FILING NOTAM INFORMATION WITH FSSs

NOTAM information should not be filed with an FSS (1-877−4−US−NTMS) prior to 3 days before the expected condition is to occur. A NOTAM must be transmitted as soon as practical but not more than 3 days before the expected condition is to occur.

Coordination 3−2−1

Chapter 3. General Operating Procedures › Section 3. Use of Terms

Section 3. Use of Terms

3−3−1. USE OF CONTRACTIONS AND ABBREVIATIONS

a. Contractions and abbreviations designated for ICAO usage as specified in FAA Order JO 7340.2, Contractions, must be used in the NOTAM system.

1. Even though SER is an ICAO contraction, SERVICE must always be spelled out, not to confuse with SVC, services keyword.

2. When an ICAO-usage contraction is not available, plain text is required, except for the list of differences in Appendix C.

b. For indicating abbreviated days of the week, use a hyphen to indicate successive days or each day can be specified individually separated by a single space; for example, MON-FRI means Monday through Friday, whereas MON WED FRI means Monday, Wednesday, and Friday.

c. Use the Pilot/Controller Glossary to define terms in the NOTAM system.

d. Location identifiers used in the NOTAM system are those contained in FAA Order JO 7350.9, Location Identifiers.

e. Use applicable contractions and abbreviations published on instrument flight procedure charts in the text of FDC NOTAMs relating to approach and departure procedures.

f. Contractions written in the singular form decode to mean both the singular and plural.

3−3−2. EXPRESSION OF TIME IN THE NOTAM SYSTEM

a. The day begins at 0000 and ends at 2359.

b. Times used in the NOTAM system are Coordinated Universal Time (UTC/Zulu) unless otherwise stated, and must be stated in 10 digits for the year, month, day, hour, and minute (YYMMDDHHMM).

c. When describing a daily schedule allow Sunrise−Sunset (SR−SS).

EXAMPLES− MON-FRI SR-SS DLY SS-SR DLY SR-1800 TUE 2300-SR

3−3−3. UNITS OF MEASUREMENT

Specify the unit of measurement in distance, height, altitude, or weight. When using an abbreviation, do not add a space between the measurement and the unit of measurement. At a minimum, latitude must be 6 digits and longitude must be 7 digits.

EXAMPLES− 500FT 12500LB 5NM 20MIN 1HR 330DEG 402646N0795856W 402646.25N0795856.95W

Use of Terms 3−3−1

3−3−4. USE OF VIRGULE (/)

The use of virgules should be limited to separate runway pairs (RWY 03/21), combining positions and affected frequencies (LOCAL CTL/CD), and equipment, affected components and frequencies (ILS GP/OM/MM, VOR/DME 111.0/CH77).

3−3−5. RUNWAY IDENTIFICATION

a. Specify the runway identification as it is published, including the leading zero (0).

b. List the runway identifications in clockwise order beginning from the 1 o’clock position.

c. Use runway pair when applicable.

d. Identify runways with the prefix RWY followed by magnetic bearing indicator.

EXAMPLE− RWY 03/21 RWY 03 RWY 21

e. Differentiate parallel runways by using the runway designators. Use R, L, and C only with runway descriptions, as in 25R, 05C, 35L. In other cases, spell out Right, Center and Left.

EXAMPLE− RWY 03L RWY 03C RWY 03R

f. Where the magnetic bearing indicator has not been established, identify the runway to the nearest eight points of the compass.

EXAMPLES− …RWY NE/SW…

3−3−6. TAXIWAY IDENTIFICATION

a. Identify taxiways with the prefix TWY followed with the taxiway designator letter or letter/number as assigned.

1. Describe a taxiway that does not have an assigned designator as adjacent to a runway or direction from runway.

EXAMPLE− …TWY PARL TWY ADJ RWY 09/27… …TWY PARL TWY…

2. When a cardinal direction is used to describe a taxiway condition, the word describing the direction must be spelled out in full to ensure that the cardinal direction is not mistaken for a taxiway designator; for example, “EAST,” “WEST,” “SOUTHWEST.”

3. Describe a helipad located on a taxiway as: …TWY C HELIPAD 3…

b. Keyword TWY may be followed by designator “ALL” to indicate every taxiway at an airport, even if there is only one taxiway as: (Can be used as “TWY ALL EXC TWY X” if needed. ) …TWY ALL…

c. For multiple taxiways, each taxiway need not be prefaced with contraction TWY;

1. Taxiway segments must be separated from each taxiway or taxiway segment with a comma and preceded by contraction TWY followed by the taxiway designator. The use of “BTN” and “AND” signifies a segment,

Use of Terms 3−3−2

UNL (unlimited)

TO POINT OF ORIGIN OBSC (obscured)

UNREL (unreliable)

AVBL or NOT AVBL CENTERED AT UNUSABLE CLSD

IRREGULAR SFC (lips, dips, bumps, holes,

ruts, breaks, etc.)

NOW (temporary)

CHANGED TO

(permanent)

UNSAFE

TO EXC NEAR BTN and AND

PLUS SEE… NOT STD NOT LGTD FLAGGED

FOR/AT (RWY) WI AN AREA

DEFINED AS

LGTD USABLE (Used in conjunction with a restriction; not by

itself)

TBL 3−3−1 NOTAM Phrases

such as TWY B BTN TWY B10 AND TWY B8. A hyphen used in a TWY NOTAM indicates all taxiways between the first and last descriptors. EXAMPLE− …TWY B3,C… …TWY A1-A6… NOTE− The example includes taxiways A1, A3, A5 and A6.

2. Multiple segments separated by commas share the same condition for example: CLSD or WIP (work in progress) SN REMOVAL. EXAMPLE− …TWY B1, B2, F, TWY B BTN TWY B10 AND TWY B8 WIP… …TWY C BTN APCH END RWY 04R AND 350FT SOUTH APCH END RWY 04L CLSD… NOTE− The originator may originate multiple NOTAMs to ensure clarity.

3−3−7. APRON IDENTIFICATION a. Identify aprons with the prefix APRON followed with the apron designator. There is no requirement for RAMP or APRON to be part of the name of the surface. Keyword may be followed by designator “ALL” to indicate every taxiway at an airport, even if there is only one taxiway as: (Can be used as “APRON ALL EXC WEST APN ” if needed.) EXAMPLES− …APRON TERMINAL APN… (Where the name is Terminal Apron) …APRON MAIN TAXILANE C … (Where the name is Main) …APRON ALL… NOTE− “ALL” is used to describe every APRON at an airport OR can be used for an airport with a single APRON. …APRON MAIN RAMP HELIPAD A1 … (Where the name of the apron is Main) NOTE− This example describes a helipad that resides on the Main Ramp.

b. SPOTS, GATES, HARDSTANDS, etc., can be used as geographical reference points to delineate a section on aprons or taxiways, but do not meet NOTAM criteria as its own “attribute”. EXAMPLE− …APRON TERMINAL RAMP BTN GATE 3 AND SPOT 4…

3−3−8. STANDARD NOTAM PHRASES The following are a listing (not inclusive) of standard terms used in NOTAMs.

Use of Terms 3−3−3

3−3−4 Use of Terms

OUT OF SERVICE FLAGGED AND LGTD ADJ NONMOVEMENT (adjacent) AREA

BARRICADED LGTD AND OPN or CLSD MARKED or NOT (means any type of BARRICADED MARKED barricade)

3−3−9. CARDINAL DIRECTIONS

Cardinal directions (excluding TAXIWAY usage) is in abbreviation format. This includes N, NNE, NE, ENE, E, ESE, SE, SSE, S, SSW, SW, WSW, W, WNW, NW, and NNW. Also included are directions for high altitude balloons – northbound – NB, northeast bound – NEB; eastbound – EB; southeast bound – SEB; southbound – SB, southwest bound – SWB; westbound – WB; northwest bound – NWB.

Chapter 4. NOTAM D Procedures › Section 1. General

Chapter 4. NOTAM D Procedures

Section 1. General

4−1−1. NATIONAL NOTAM OFFICE RELATIONSHIPS

a. The USNOF is charged with monitoring the NS. The USNOF must monitor the NOTAM system for compliance with the criteria and procedures set forth in this order. When questions arise on NOTAM dissemination, formats, contractions, or other aspects of the distribution system, the USNOF should be consulted. The authority for NOTAM formats is the USNOF, who will ensure that issued NOTAMs are consistent with FAA policy. NOTAM originators and certified sources must comply with USNOF personnel guidance. Discrepancies in procedures or format must be recorded, and Aeronautical Information Services must forward a list of the discrepancies to Flight Services, Safety and Operations Support, Operational Procedures, and the service area office.

b. Editing:

1. The USNOF may edit any NOTAM (except FDC NOTAMs relating to instrument flight procedures) that does not conform to the formats and/or examples contained in this order. The contents of a NOTAM must not be changed without notifying the originating facility.

NOTE− FDC NOTAMS relating to instrument approach and departure procedures are originated by the Mission Support Services – Aeronautical Products Office under the Flight Standards Service policy contained in FAA Order 8260.19, chapter 2, section 6. ARTCCs must ensure the origination of NOTAMs pertaining to a Standard Terminal Arrival (STAR).

2. Should the USNOF edit a NOTAM and change the intent, the NOTAM must be canceled by the issuing facility and reissued as a new NOTAM, after consultation with the USNOF.

General 4−1−1

Chapter 4. NOTAM D Procedures › Section 2. Preparing NOTAMs for Dissemination

Section 2. Preparing NOTAMs for Dissemination

4−2−1. NOTAM COMPOSITION

NOTE− For FDC NOTAM examples, see Appendix A.

FIG 4−2−1 NOTAM Diagram

Where the solid lines indicate mandatory and the dashed lines indicate as needed or optional.

a. The purpose of the NOTAM diagram is to provide a basic outline of what constitutes a NOTAM. Not all NOTAMs will contain all of the elements. For detailed explanation, consult the applicable paragraph sections for further NOTAM composition assistance.

b. NOTAMs may contain these elements from left to right in the following order:

1. An ADP code/exclamation point (!).

2. Accountability (the identifier of the accountability location; for example, JFK, FDC, CARF).

3. Location identifier {the affected facility or location (airport, NAVAID, or ARTCC) appears AFTER the NOTAM number}. Approach controls or airspace located within multiple ARTCC must have a separate NOTAM for each ARTCC.

(a) The nearest public use airport when the full activity is completely within a 5NM Radius of the airport.

(b) The nearest VOR when any of the activity is more than 5NM from the nearest public use airport but completely within 25NM Radius of a VOR

(c) When the activity doesn’t fall within either (a) or (b), use the ARTCC.

4. Keyword.

5. Attribute, activity, or surface designator(s) (when needed).

NOTE− A surface designator is required with keywords RWY, TWY, and APRON.

6. Surface segment (when needed).

7. Facility, feature, service, system, and/or components thereof (when needed).

8. Location description (when needed).

9. Lower limit then upper limit, or height, (when needed). Limits must be specified, as:

Preparing NOTAMs for Dissemination 4−2−1

(a) For SFC, or 1 to 17,999FT with the unit of measurement (AGL or MSL). 50FT, 1275FT AGL, 10500FT.

(b) For 18,000FT and above, express in flight levels (FL), FL180, FL550, FL850, or UNL (altitudes greater than 99,900FT).

(c) Heights AGL may be added when required or when MSL is not known, for example, SFC-450FT AGL.

(d) The term UNKNOWN may be used in lieu of the MSL or AGL altitudes if not known; however, one altitude must be identified.

10. Condition. The changed condition or status being reported, when needed. When the conditions includes a limitation or an exception, follow the condition with “TO” or “EXC”; such as, “CLSD EXC SKI” or “CLSD TO TRANSIENT” or “CLSD EXC TAX BTN APCH END RWY 10 AND TWY C.”

11. Reason (when needed).

12. Remarks (when needed). Other information considered important; for instance a frequency (134.72), or an expected altitude for unmanned free balloons (NEB 150000FT)

13. Schedule, (when needed). A NOTAM may be originated for a scheduled condition/activity that will occur during the period. Specify the schedule between the condition/activity and the valid time string. The days of the week must be specified before the scheduled time. The term “DLY” (daily) indicates the event will occur each day at the same time during the stated time period. The start time of the schedule must correspond to the start of activity time. The end of the last schedule must correspond to the end of validity time. For example : DLY 1200-2000 YYMMDD1200-YYMMDD2000, MON WED 0900-1300 YYMMDD0900-YYMMDD1300, TUE THU 0900-2000 YYMMDD0900-YYMMDD2000.

If the active time of a NOTAM corresponds to sunrise or sunset, the actual times of sunrise on the first day of validity and of sunset on the last day of validity should be used.

14. Start of Activity/End of Validity. This is a 10-digit date-time group (YYMMDDHHMM) used to indicate the time at which the NOTAM comes into force (the date/time a condition will exist or begin) and the time at which the NOTAM ceases to be in force and becomes invalid (the expected return to service, return to normal status time, or the time the activity will end). These times must be separated by a hyphen “-.”

(a) If the NOTAM duration is expected to return to service prior to the End of Validity time, express the time by using a date-time group followed immediately by “EST” (estimate). Any NOTAM that includes an “EST” must be canceled or replaced before the NOTAM reaches its End of Validity time. If the NOTAM is not canceled or replaced, it will expire at the end of validity time regardless of EST. FDC NOTAMs relating to instrument flight procedures must not be canceled and reissued. (Reference FAA Order 8260.19, Chapter 2, Section 6.)

(b) When a NOTAM is originated to advertise a permanent condition that will be published in a publication, chart or database “PERM” should be inserted as the expiration date in lieu of a 10−digit date−time group. PERM is also used as the end of validity for certain NOTAMs that 1) pertain to or support national security, law enforcement, and aviation security requirements, and 2)contain flight prohibitions for U.S. operators and U.S. airmen regarding operations in particular areas of non−U.S. controlled airspace due to weapons related hazards or other hostile threats to civil aviation. The NOTAM originator is responsible for canceling the NOTAM upon publication, as PERM will not auto−expire.

(c) All NOTAMs will auto-cancel at their End of Validity time, except PERM.

c. NOTAMs issued when the condition of a number of facilities, NAVAIDs, services, or landing areas/runways are related to the same event (for example, date/time, facility closing, part−timing, runway closures, etc.) must be issued as separate NOTAMs.

d. Each NOTAM concerning a specific aid, service, or hazard must be a complete report including all deviations unless reference is made to other restrictions already published.

4−2−2 Preparing NOTAMs for Dissemination

e. If information is published elsewhere and is still valid, reference must be made to that publication with the statement, “PLUS SEE (publication).” A NOTAM issued not stating “PLUS SEE (publication)” indicates the NOTAM replaces previously published similar data.

f. NOTAMs must state the abnormal status of a component of the NAS and not the normal status. Exception − Temporarily extending hours of use beyond published times, for example: RWY 09/27 OPN.

4−2−2. NOTAM ACCOUNTABILITY

Maintain separate accountability (NOTAM file) for each location whose weather report is disseminated via WMSCR and for the location of the tie-in FSS.

a. Issue NOTAMs for an FAA-monitored weather reporting location whose report is disseminated via WMSCR under the location identifier of the weather report.

b. Issue all other NOTAMs under the location identifier of the tie-in FSS. This includes NOTAMs for weather reporting locations whose report is not disseminated via WMSCR.

REFERENCE− FAA Order JO 7930.2, Chapter 2, Aeronautical Information Services

c. Make NOTAM accountability changes by mail, email or other electronic means when known sufficiently in advance. Issue all subsequent NOTAMs under the corrected accountability. If there are any current NOTAMs for the location, cancel and reissue those NOTAMs under the new accountability after the NS tables have been changed. Notify Aeronautical Information Services of any NOTAM accountability changes.

Preparing NOTAMs for Dissemination 4−2−3

Chapter 4. NOTAM D Procedures › Section 3. Canceling/Extending NOTAMs

Section 3. Canceling/Extending NOTAMs

4−3−1. EXTENDING NOTAM VALIDITY

a. When there is a need to extend an existing NOTAM time validity, cancel the original NOTAM, and reissue the data as a new NOTAM with the new time.

4−3−2. CANCELLATION OF NOTAMs

a. Stations canceling NOTAMs must check the NOTAM data to ensure the NOTAM’s deletion. Retransmit cancellations where no action was taken.

b. Cancel NOTAMs containing erroneous information, and reissue. Originate a new NOTAM when data is received amending a current NOTAM, and cancel the previous NOTAM.

4−3−3. CANCELING PUBLISHED NOTAM DATA

a. When data appearing in a NOTAM is printed correctly in a publication or on a chart, cancel the NOTAM.

b. NOTAMs must remain current until the data is published in one or more of the following, with the exception of NAVAID NOTAMs, which must remain in effect until the NAVAID is returned to service or decommissioned:

1. Airport/Facility directory.

2. Enroute low altitude charts.

3. Enroute high altitude charts.

4. Terminal procedures publications.

NOTE− FDC NOTAMs relating to instrument approach and obstacle departure procedures and airways must remain current until published in the Terminal Procedures Publication or applicable enroute chart.

5. Supplements (Alaska and Pacific).

6. VFR Charts:

(a) Sectional charts.

(b) World aeronautical charts.

(c) Terminal area charts.

c. The NTAP conveys NOTAMs to the public until printed correctly on publications listed in subparagraph b above. The NTAP does not cancel NOTAMs but may supplement briefings. The NTAP must not be used as a basis to cancel NOTAMs.

d. NOTAMs concerning Army airfield operations, in addition to the above listed sources, must be researched in the Army Aviation Flight Information Bulletin, if applicable.

Canceling/Extending NOTAMs 4−3−1

Chapter 5. NOTAM Criteria › Section 1. Movement Area NOTAMs

Chapter 5. NOTAM Criteria

Section 1. Movement Area NOTAMs

5−1−1. ORIGINATORS OF AERODROME NOTAMs

a. Airport management is responsible for observing and reporting the condition of the aerodrome services, facilities, and movement area. The FSS air traffic managers must coordinate with appropriate airport managers to obtain a list of airport employees who are authorized to originate NOTAMs.

b. At public airports without an airport manager, the FSS air traffic manager must coordinate with the appropriate operating authority to obtain a list of persons delegated to provide NOTAM information.

NOTE− Letters of agreement should be executed between airport management and ATC facilities outlining procedures to be used for originating NOTAMs.

5−1−2. HANDLING REPORTED AERODROME CONDITIONS

a. Copy any information received verbally, and record the name, title (if appropriate), address, and telephone number of the person submitting the information. Information obtained from other than an authorized airport or FAA employee must be confirmed before issuance. If you are informed of or observe a condition that affects the safe use of a movement area, relay the information to the airport management for action.

NOTE− This includes data received from airport inspectors.

b. If unable to contact airport management, classify and issue a NOTAM publicizing the unsafe condition always stating the condition and including the word “UNSAFE;” for example, RWY number or TWY letter or letter/number “UNSAFE DISABLED ACFT.” Inform airport management of the action taken as soon thereafter as practical.

c. (U) – Unverified aeronautical information (for use only where authorized by letters of agreement). Movement area or other information received that meets NOTAM criteria and has not been confirmed by the airport manager or designee. If Flight Service is unable to contact airport management, Flight Service must forward (U) NOTAM information to the NS. Subsequent to NS distribution of a (U) NOTAM, Flight Service will inform airport management of the action taken as soon as practical. Any such NOTAM will preface the keyword with “(U)” and must include the condition and cause.

5−1−3. MOVEMENT AREA INFORMATION

FIG 5−1−1 Movement Area Diagram

…AD AP CLSD EXC PPR MON−FRI 0330−1430 1310120330−1310171430

Movement Area NOTAMs 5−1−1

See Appendix A for examples.

Originate a NOTAM D for:

a. Aerodrome conditions. Use the keyword “AD” immediately followed by the facility: “AP”, “HELIPORT”, or “SEAPLANE BASE”, followed by the condition. When the condition includes a limitation, follow the condition with “TO” or “EXC;” for example, “CLSD EXC SKI” or “CLSD TO TRANSIENT.”

b. Commissioning of a movement area or portions thereof. State the type of surface, length and width of the surface, lighting status, and declared distances.

1. Lighting status; for example, LGTD, NOT LGTD.

2. Length and declared distances required for only runway commissioning.

c. Closure of a movement area or portion thereof. Partial runway closures must be indicated by feet , for example, E 500FT.

1. Permanent closure (decommissioning). State the surface description and the condition “CLSD” with expiration time “PERM.”

2. Temporary Nonmovement Area. Use this feature when a taxiway is temporarily designated as Non Movement in a NOTAM.

d. Operational limitations on the use of any portion of a runway, a taxiway, a ramp, an apron or a waterway. Weight bearing capacity of a runway can be changed only by authorization of the Manager, Airports Division (appropriate region). Include reference to ACFT when describing limitations associated – wing, weight, tail, engine, taxi speed, etc.

e. Changes to usable runway length and declared distances.

1. When a runway condition restricts or precludes the use of any portion of a runway resulting in a change to the declared distances, include the published take-off run available (TORA), take-off distance available (TODA), accelerate− stop distance available (ASDA), and landing distance available (LDA) in the NOTAM. Ensure that a second NOTAM is originated for the reciprocal runway with all declared distances if any value has changed. Declared distances can only be authorized by the FAA Office of Airport Safety and Standards, Airport Design Division, AAS−100.

2. In the event the published TORA, TODA, ASDA, and LDA need to be reported without reference to the runway condition that caused the change, report declared distances or changes to published declared distances. For example, when the published runway length is changed, report the declared distances, or erroneous declared distances that were published and need to be corrected.

f. Change of runway identification.

g. Change of traffic pattern.

h. Runway Visual Range (RVR). When originating a NOTAM on RVR, RVR touchdown (RVRT), RVR midpoint (RVRM), and RVR rollout (RVRR), specify the single runway affected. When all the RVRs are out of service, issue a NOTAM using the keyword AD.

Movement Area NOTAMs 5−1−2

i. Surface Markings and Signage. Follow 4-2-1 b 1-3, including:

1. Keyword. Specify the keyword for the type of surface on which the sign/marking is located.

2. Surface designator. Specify the designator of the surface on which the sign/marking is located.

3. Geographical Relationship of surface from relevant intersection/point of reference, (N OF, E OF), if needed.

4. Name of sign/surface marking. Signs follow runway identification guidance.

5. Sign/ marking location from users’ perspective (LEFT/RIGHT SIDE; FOR RWY; AT RWY), when needed.

6. Condition. For example, NOT STD, NOT LGTD, OBSC, MISSING, NOT MARKED

7. Follow 4-2-1 b 11-14 to complete the NOTAM.

j. Other reportable conditions. The airport operator must ensure that a NOTAM is submitted for conditions considered to be hazardous or potentially hazardous to the aircraft operator. Permanent changes in surface conditions must be coordinated for publication in accordance with Paragraph 2−1−3, Publication Criteria.

1. When SNOWBANKS, BERMS, DRIFTS, WINDROWS and SN PILES are not on the movement areas, issue them without the FICON descriptor.

2. When it is determined that no surface condition reports will be taken for longer than a 24-hour period, issue a single NOTAM (Keyword AD) for the entire time-period. Use the phrase “SFC CONDITIONS NOT REPORTED”, as this differs from Conditions Not Monitored.

5−1−4. FIELD CONDITIONS (FICON) REPORTING

FIG 5−1−2

FICON

…RWY 33 FICON 4/4/4 100 PRCT COMPACTED SN PLOWED 100FT WID 24IN BERMS…

See Appendix A for examples.

Report surface conditions on runways, taxiways, and aprons using the FICON NOTAMs. The keyword AD must not be used with descriptor FICON, except for heliport.

…AD HELIPORT FICON 4IN DRY SN OBSERVED AT XX12051621...

…AD HELIPORT FICON 2IN DRY SN PLOWED 50FT WID 4FT SNOWBANKS OBSERVED AT XX12070959…

Runway

Takeoff and Landing Performance Assessment (TALPA) FICONs are reported in thirds of the landing runway, except when reporting Slippery When Wet. Runways are described using the RWY keyword followed by a single runway direction designator, FICON and condition.

Movement Area NOTAMs 5−1−3

…RWY 04 FICON…

Taxiway

Taxiways are described using the TWY keyword followed by a surface name/designator, FICON and condition. Depth is required and a width is optional.

…TWY A FICON 1/2IN WET SN…

…TWY A FICON 1/2IN WET SN 50FT WID REMAINDER COMPACTED SN…

Apron

Aprons are described using the APRON keyword followed by a surface name/designator, FICON and condition. Depth is required and a width is optional.

…APRON MAIN RAMP BTN RWY 13/31 AND TWY C FICON 1IN DRY SN…

Helipad

Helipads are described using TWY or APRON keywords followed by HELIPAD (surface designator) FICON and condition.

…APRON HELIPAD H1 FICON 2IN DRY SN…

…APRON HELIPAD C FICON DRY PLOWED 50FT WID REMAINDER COMPACTED SN…

a. Airport operators use the Runway Condition Assessment Matrix (RCAM − See Table 5−1−5) to create the Runway Condition Code (RwyCC) for Paved Surfaces, which include asphalt, asphalt−concrete, concrete, and porous friction course. Non−paved surface NOTAMs do not include the RwyCC. The NS generates the RwyCC based on airport operator input of the contaminants present. Per AC 150/5200−30, Airport Field Condition Assessments and Winter Operations Safety, airport operators have the capability, in accordance with specific action and protocols, to downgrade or upgrade the runway condition code.

b. Each field of the NOTAM is described below. Follow the NOTAM composition in 4−2−1 a 1−4 to include:

1. Surface Designator (RWY 04)

2. FICON. Insert “FICON” after the surface designator and before the field condition.

3. RwyCC. When generated, it will be illustrated as values between 0 and 6 and look similar to this for runway thirds (3/4/2). The RwyCC will only be provided for paved runways when the percentage coverage of the full runway that is contaminated is greater than 25%.

4. Condition. Report the contaminants per Table 5−1−3, including the percentage of coverage for runways, in thirds.

(a) Runways, including ski strip and waterlane.

(1) RWY: Each third (touchdown, midpoint, and rollout) will include percentage, depth (when required), and type of contaminant. Up to two separate contaminants can be reported per runway third.

(2) A runway is dry when it is neither wet, nor contaminated. A FICON NOTAM must not be originated for the sole purpose of reporting all thirds of a runway are dry. A dry surface must be reported only when there is need to report conditions on the remainder of the surface. When describing a dry surface, it is considered the full length and width of the runway third. DRY can be reported in two thirds and the remaining third have a different contaminant.

EXAMPLE− … FICON 10 PRCT 1IN WET SN, 10 PRCT 1/8IN DRY SN OVER ICE AND 10 PRCT 1/8IN DRY SN, DRY…

(3) A runway is wet when there is any visible dampness or water that is 1/8 inch or less in depth. When describing a wet surface, include the percentage.

(4) If all three thirds are identical percentage, depth (when required) and type of contaminant, it is shown in the NOTAM once.

Movement Area NOTAMs 5−1−4

EXAMPLE− …FICON 4/4/4 75 PRCT COMPACTED SN…

(b) Taxiways and Aprons. The condition includes depth and type of contaminant.

NOTE− Free−form is an acceptable means of entering FICONs for TWY and APRONs.

5. Action. Action taken to treat the contaminated surface.

(a) Includes the treatment method (Up to three treatments permitted for full length of runway/taxiway/apron.) Treatment includes plowed, swept, sanded, deiced liquid, deiced solid, scarified (for runways, each third must be contaminated with only ice and the total surface coverage must be >25% ).A treatment width of 50FT is considered 25ft on each side of the centerline.

(b) Includes width of PLOWED or SWEPT treatment if not the full width. The treatment is omitted when the entire surface has been plowed or swept.

(c) Includes SANDED when a surface has been treated with sand.

(d) Includes DEICED LIQUID or DEICED SOLID or both to report the presence of liquid or solid deicing material, as this can have operational significance to the pilot.

(e) Includes ridges (when applicable) to describe the accumulation at the edge of the treated area. Ridges include snowbanks, berms, windrows, snow piles and drifts.

(1) Use the term “DRIFTS” after any treatments to describe one or more drifts. When the drifts are variable in depth, report the greater depth.

(2) Use the terms “SNOWBANKS,” “BERMS,” “SN PILES” or “WINDROWS” after the surface condition. Snowbanks must be assumed to be at the edge of a movement surface or, when plow/sweeper is used, at the edge of the plowed/swept area.

EXAMPLE− …FICON 5IN DRIFTS…

(f) Includes “Remainder” to describe the non−treated depth and type of contaminant for full length of runway/taxiway/apron to provide additional information about the surface condition. For example, a runway has been treated, resulting in differing field conditions on the untreated parts of the surface.

EXAMPLE− …FICON 4/4/4 50 PRCT COMPACTED SN PLOWED 75FT WID REMAINDER 1/2IN DRY SN… …FICON 25 PRCT COMPACTED SN AND 10 PRCT ICE, 25 PRCT 2IN DRY SN, DRY PLOWED 75FT WID REMAINDER 1/2IN DRY SN…

6. Braking Action (BA). (APRONs, TWYs and Non−Paved RWYs). Report braking action on movement areas as good, good to medium; medium; medium to poor; poor; or nil, as received from airport management. The worst runway braking action is shown by contaminant type and RwyCC.

(a) Reporting of a “NIL” braking condition is not permissible by Federally Obligated Airports or those airports certificated under 14 CFR part 139. A “NIL” braking condition at these airports must be mitigated by closure of the affected surface.

(b) Paved surfaced runways cannot have a stand−alone BA NOTAM.

(c) Non−Paved surfaced runways can have BA, but as a stand−alone NOTAM.

(d) TWY/Apron can have BA as stand−alone or appended to field condition NOTAM.

EXAMPLE− …TWY A FICON BA GOOD TO MEDIUM… …TWY A FICON 1/8IN WET SN BA MEDIUM…

7. Observation Time. The time airport management observed the conditions.

Movement Area NOTAMs 5−1−5

8. Conditions Not Monitored (when applicable). When an airport operator cannot monitor the condition of the movement area or airfield surface, this information is issued as a NOTAM. Usually necessitated due to staffing, operating hours or other mitigating factors associated with airport operations. When the field conditions will not be monitored, follow the most recent observation with the words “CONDITIONS NOT MNT (date/time) (date/time).” The time parameters specified must fall within the start of activity/end of validity times.

9. Start of Activity/End of Validity. FICON NOTAMs are considered temporary, therefore the End of Validity time for FICON NOTAMs must not exceed 24 hours from the Start of Activity time, except:

(a) When the reported contaminant is ASH, MUD, OIL RUBBER (taxiway only), or SAND.

(b) When appended with remarks “CONDITIONS NOT MNT.”

c. Rubber as a contaminant/Slippery When Wet.

1. Rubber is used on Taxiways only to describe the accumulation of rubber.

EXAMPLE− …TWY A FICON RUBBER…

2. Slippery When Wet is a stand−alone NOTAM, used only on runways, when describing a rubber accumulation. This is the only FICON that is described using both runway ends.

EXAMPLE− …RWY 02/20 FICON 3/3/3 SLIPPERY WHEN WET…

NOTE− May be downgraded to 2/2/2 or 1/1/1 with all numbers matching.

TBL 5−1−1 Reportable Depth Measurements

Use Value To Report

1/8IN ⅛ inch or less

1/4IN >⅛ inch to and including ¼ inch

1/2IN >¼ inch to and including ½ inch

3/4IN >½ inch to and including ¾ inch

1IN >¾ inch to and including 1 inch

(a) When 1 inch is reached, report values in multiples of 1 inch and discontinue the use of fractions. When a snow depth of 35 inches is reached, report values in multiples of feet only. Round depths greater than 1 inch to the next higher reportable depth.

(b) Report the highest depth of the contaminant along the reported portion of the surface.

TBL 5−1−2 Reportable Contaminants

Wet (includes damp and ⅛ inch depth or less of water)

Compacted snow

Water* (greater than ⅛ inch depth) Water* over compacted snow

Frost West snow* over compacted snow

Slush* Dry snow* over compacted snow

Ice Slush* over Ice

Wet ice Slippery When Wet

Wet snow* Ash

Wet snow* over ice Rubber (taxiways only)

Movement Area NOTAMs 5−1−6

Dry snow* Oil

Dry snow* over ice Sand

Mud* (See AC 150/5200−30)

REFERENCE− AC 150/5200−28, Notices to Airmen for Airport Operators Those contaminants marked by an asterisk “*” are to be accompanied by a depth. Part 139/Federally obligated airports are required to report depth on taxiways and aprons. It is optional for other airports to report depths on taxiways and aprons.

TBL 5−1−3 Percent Coverage of a Contaminant

10 10% or less

20 11% − 20%

25 21% − 25%

30 26% − 30%

40 31% − 40%

50 41% − 50%

60 51% − 60%

70 61% − 70%

75 71% − 75%

80 76% − 80%

90 81% − 90%

100 91% − 100%

Movement Area NOTAMs 5−1−7

TBL 5−1−4 Runway Condition Assessment Matrix

Movement Area NOTAMs 5−1−8

5−1−5. AERODROME FACILITIES

FIG 5−1−3 Aerodrome Facilities

…AD AP CLSD EXC PPR MON−FRI 0330−1430 1310120330−1310171430

See Appendix A for examples.

Issue a NOTAM if any aerodrome service availability has changed from that which is published.

a. Certified Aircraft Rescue and Fire Fighting (ARFF).

1. Issue a NOTAM D on airports (not runways) certificated under 14 CFR Part 139, when notified by airport management that required ARFF equipment is inoperative/unavailable and replacement equipment is not available. Except as indicated in paragraph 5-1-5a 3, airport management has 48 hours to replace or substitute equipment before the index changes. Air carriers and others must be notified that ARFF equipment is out of service. Each NOTAM must have an expiration time as obtained from airport management. If unable to obtain an expiration time, add 48 hours to the time of receipt and advise airport management.

NOTE− The ARFF Index for each certificated airport is published in the U.S. Chart Supplement, which lists indices and ARFF equipment requirements.

2. At certificated airports listed in the U.S. Chart Supplement, the certificate holder (airport management) is required to notify air carriers by NOTAM when required ARFF equipment is inoperative/unavailable and replacement equipment is not available immediately. If the required Index level of capability is not restored within 48 hours, airport management is required to limit air carrier operations.

REFERENCE− Title 14 CFR Part 139

3. If the ARFF vehicle is still out of service after 48 hours, the airport manager must notify the FSS of a temporary index change and approximate duration time.

4. If the ARFF Index is listed in the U.S. Chart Supplement, as A and the ARFF vehicle is out of service, the NOTAMs must indicate that index A is not available and the airport is closed to air carrier operations.

b. Fuel services.

c. Custom Services.

d. Aerodrome beacon (ABN). Describe the beacon status as accurately as possible. For example, ABN NOT ROTATING; ABN NOT STD GREEN ONLY

e. Wind direction equipment, including wind cones, wind direction indicator, wind sock, etc.

5−1−6. WORK IN PROGRESS

Movement Area NOTAMs 5−1−9

FIG 5−1−4 Work in Progress

…TWY C WIP TRENCHING ADJ EAST SIDE…

See Appendix A for examples.

a. Work in Progress (WIP) describes any work being done on the airport surface, including construction, mowing, snow/ice removal, etc. WIP does not close a movement area; therefore, if the movement area is restricted, another NOTAM identifying that restriction is needed. For example, a WIP with snow removal requires a closure NOTAM with 15 minute PPR in order to use the surface.

b. WIP (reason) is mandatory for describing construction and snow/ice removal NOTAMs. Other WIP reasons are optional.

c. Any NOTAM associated with work in progress on or adjacent to a runway, taxiway, apron/ramp, or aerodrome must be formatted as follows 4-2-1 b 1-3, including:

1. Keyword. RWY, TWY, APRON, or AD.

2. Surface name/designator. Specify the name/ designator of the surface on which the work is being conducted.

3. Surface segment description must be specified in feet or from a specific point to point; for example, TWY A SOUTH 76FT or TWY A BTN TWY B AND TWY C.

NOTE− A surface segment differs from the optional plain language description of the work areas in that the surface segment description can be captured and depicted graphically in a digital environment. The optional plain language comments will be delivered in text form only.

4. Condition or activity; “WIP.”

NOTE− Airport operators must ensure this NOTAM remains active only when actual snow and ice removal operations are taking place.

5. Reason or purpose.

6. Remarks. The work area may be described in plain language text after the reason by specifying the area by cardinal direction in relationship to the work area, by an intersection, or distance from an intersection.

7. Follow 4-2-1 b 13 and14 to complete the NOTAM.

Movement Area NOTAMs 5−1−10

Chapter 5. NOTAM Criteria › Section 2. Lighting Aid and Obstruction NOTAMs

Section 2. Lighting Aid and Obstruction NOTAMs

5−2−1. LIGHTING AIDS

FIG 5−2−1 Lighting Aids

…RWY 27 RTHL OUT OF SERVICE…

See Appendix A for examples.

Originate NOTAMs on operational status of lighting aids for public use civil landing areas listed in the U.S. Chart Supplement. Each type of lighting requires separate NOTAMs. Technical Operations must be made aware of any runway lighting outages, as this is the office that maintains the equipment. When describing restrictions, use Runway Centerline (RCL) with visual navigational aids. NOTAMS regarding lighting aids are originated as follows:

a. Approach light systems (ALS). Only use the runway direction for which the equipment pertains.

1. When commissioning approach light systems, indicate the exact type of system; for example, MALSR, MALSF, etc.

2. Once commissioned and published, approach light systems need only be shown as ALS.

b. Lead off /lead on lights. NOTAMs issued using keyword RWY. Lead off and lead on light will be the standardized verbiage for lead off/on lights, which are also referred to as turnoff lights.

c. Runway status light system.

1. Runway entrance lights. NOTAMs issued using keyword TWY

2. Take-off hold lights.

d. Sequence flashing lights/runway alignment indicator lights.

e. Visual approach lighting.

1. Visual approach slope indicator (VASI).

2. Precision approach path indicator (PAPI).

3. Runway end identifier lights.

4. Threshold lights (RTHL).

f. Runway edge lights (REDL).

1. When commissioning runway edge light systems, indicate the exact type of system; for example, LIRL, MIRL, HIRL, etc.

2. Once commissioned and published, runway edge lights must only be shown as REDL.

3. Runway lights obscured due to snow and ice.

Lighting Aid and Obstruction NOTAMs 5−2−1

g. Runway centerline light (RCLL).

h. Touchdown zone lights (RTZL).

i. Runway lead-in lighting system (RLLS).

j. Airport lighting total power failure.

k. Pilot-controlled lighting (PCL) frequency when it controls approach lights or runway lights.

l. Taxiway lighting.

1. Taxiway edge lights.

2. Taxiway centerline lights.

3. Runway guard lights. NOTAM issued using keyword TWY.

4. Stop bar lights. NOTAM issued using keyword TWY.

5. Taxiway lights obscured due to snow and ice.

5−2−2. OBSTACLES

FIG 5−2−2 Obstacles

…OBST CRANE (ASN 2013−ACE−5−NRA) 345140N0804506W (1.44NM SW N52) 580FT (195FT AGL) NOT LGTD…

See Appendix A for examples.

a. Obstructions to include telecommunications antenna tower lights, cranes, stacks, wind turbines, non-FCC towers, power lines, moored balloon, kites, natural growth/terrain, etc.

b. Any failure or malfunction which affects a top light or flashing obstacle light regardless of its position is a condition for a NOTAM.

c. Commercial tower light operators must report the operating status of tower lights and ensure that a NOTAM is originated via a direct entry tool or contacting FSS.

d. The NOTAM text for obstructions to air navigation must be formatted as follows 4-2-1 b 1-2, including:

1. Location Identifier: For wind turbine farms, use the ARTCC under which the farm falls.

2. Keyword “OBST.”

3. Specify the attribute; for example, “TOWER LGT”, “CRANE,” “STACK,” “ACFT TAIL,” “BUILDINGS,” “MOORED BALLOON”, “KITE” etc.

4. Assigned obstruction identifier.

(a) For FCC Towers, the Antenna Structure Registration (ASR), if known, in parentheses. If the ASR is not known, indicate by (ASR UNKNOWN) in the NOTAM.

(b) For Cranes, Stacks, etc., the Aeronautical Study Number (ASN), if known, in parentheses. If the ASN is not known, indicate by (ASN UNKNOWN) in the NOTAM. Do not include the ASN for wind turbine farm NOTAMs, see examples.

5−2−2 Lighting Aid and Obstruction NOTAMs

(c) For Moored Balloon, which requires a waiver to 14 CFR Part 101, the assigned obstruction identifier is not required.

5. For FCC Tower Obstructions, enter the location by latitude and longitude to the nearest one hundredth of a second. For wind turbine farms, if using latitude and longitude, provide the coordinates for the center point of the wind farm, or the coordinates for one of the turbines closest to the center. If the latitude and longitude is not known, use “UNKNOWN”. For all other obstacles, use the latitude and longitude to the nearest second, or fix/radial/distance, or a nautical mile radius of a NAVAID.

6. Plain language location in parentheses.

(a) When the obstacle is within 5SM of an airport, describe the plain language location in feet or nautical miles using 16 points of compass from a specified location on the airport; for example, (.5NM E APCH END RWY 18) (2000FT SSE DEP END RWY 20) (2NM SSW ACY).

(b) When the obstacle is within 500 feet either side of the centerline of a charted helicopter route, or 5SM or more from an airport and more than 200 feet AGL, describe the plain language location by using the bearing, distance, and aerodrome designator of the nearest public-use airport; for example, (12NM SSW SPA).

7. Specify the altitude MSL with the unit of measurement (FT), if known. Otherwise state UNKNOWN. For wind turbine farms, use the tallest height of a turbine within the farm.

8. In parentheses, specify the height with the unit of measurement (FT) and reference datum (AGL).

NOTE− Report the height of obstruction lights on terrain (hills) in MSL only, as the terrain is the obstacle, not the light on the terrain

9. Specify the condition:

(a) “OUT OF SERVICE” for FCC obstructions. A light condition of OUT OF SERVICE refers to a top light or flashing obstruction light is not operating, regardless of its position.

(b) “NOT LGTD,” “LGTD,” “FLAGGED” for non-FCC obstructions, for example. As used in a NOTAM, NOT LGTD refers to a facility (sign) that is installed, but the lights aren’t lit.

10. Start of Activity/End of Validity. FCC receives notification upon ASR NOTAM issuance.

Lighting Aid and Obstruction NOTAMs 5−2−3

Chapter 5. NOTAM Criteria › Section 3. NAVAID NOTAMs

Section 3. NAVAID NOTAMs

5−3−1. GENERAL

Technical Operations personnel must ensure the origination of NOTAM Ds concerning NAVAIDs for which they are responsible.

5−3−2. REPORTING NAVAID MALFUNCTIONS

Known or reported malfunctions of a navigational aid must be reported to Technical Operations or appropriate personnel.

5−3−3. UNPROGRAMMED EXTENDED SHUTDOWNS

Unprogrammed, extended facility shutdowns or other unanticipated outages that are expected to last more than 30 days must be promptly reported to NFDC. When possible, the expected duration of the shutdown is to be included in the message.

NOTE− Except for emergency shutdowns, technical operations personnel are expected to give at least 1 hour notice.

5−3−4. NAVAID MAINTENANCE SHUTDOWNS

Information concerning maintenance shutdown of NAVAIDs that are part of the NAS must be handled as follows:

a. Routine maintenance shutdown. When possible, approval should be obtained sufficiently in advance of the proposed shutdown time to allow dissemination of a NOTAM at least 5 hours before a shutdown will occur. A routine maintenance shutdown request must not be denied because of an inability to issue a NOTAM 5 hours in advance of the shutdown.

b. Emergency shutdown. When possible, obtain at least 1 hour advance notice so that appropriate dissemination may be made before shutdown.

c. Extended maintenance shutdown. Notify the NFDC sufficiently in advance to permit publication of the information prior to the shutdown date. When this is not possible, disseminate a NOTAM no more than 3 days before the shutdown.

5−3−5. UNMONITORED NAVAIDs

a. All VOR, VORTAC, and ILS equipment in the NAS have automatic monitoring and shutdown features in the event of malfunction.

b. When a navigational aid’s operational status cannot be monitored at the controlling or monitoring facility, but all indications or reports are the facility is operating normally, Technical Operations personnel must ensure the origination of a NOTAM placing the aid in an unmonitored status.

c. When issuing a NOTAM describing a facility as unmonitored, do not use the category of monitor, only the phrase “NOT MNT.”

d. If the NAVAID is reported as being out of service, the unmonitored NOTAM must be canceled.

5−3−6. INSTRUMENT LANDING SYSTEM STATUS

a. Technical Operations issue NOTAMs related to outages or restrictions on NAVAID components of ILS approach systems, for which they own/maintain/certify. AIS NOTAM Office is responsible for issuing any

NAVAID NOTAMs 5−3−1

procedural NOTAMs, such as flight data center (FDC) NOTAMs. Consult FAA Order 6750.24 to determine if any additional NOTAM Ds should be issued. Ideally, a NOTAM will allow authorized operators to continue, while notifying unauthorized operators that the specified approach procedure is not available. It is critical that required NOTAMs alert users of an inoperative facility or system. In some situations, an all−encompassing cancellation of specific minima (e.g., “CAT II/III Not Authorized”) may not be necessary.

b. Category II and/or III approaches may not be authorized due to the failure of additional equipment, as specified in FAA Order 6750.24. The Technical Operations Control Center specialist in accordance with the guidance contained in FAA Order 6750.24 will make the determination of impact to Category II/III ILS operations, and a separate NOTAM request for loss of ILS category will be made if the equipment failures warrant this action.

c. When Technical Operations personnel issue a NOTAM suspending CAT II/III minimums, AIS must be notified. If the suspension will exist longer than 224−days or is permanent, AIS must submit a full or abbreviated procedure amendment prior to the 224−day suspense.

d. Special Authorization CAT II approaches. These Part 97 CAT II approaches are identified as “ILS RWY XX (SA CAT II)” and by an additional chart note saying “Reduced Lighting: Requires specific OpSpec, MSpec, or LOA approval and use of autoland or HUD to touchdown.”

1. The aircraft operator is authorized to conduct CAT II IAP on certain ILS facilities that do not meet the equipment requirements of a U.S. Standard or ICAO Standard, for example when TDZ lighting or RCL become inoperative. These procedures have been specifically approved in accordance with FAA Order 8400.13, Procedures for the Evaluation and Approval of Facilities for Special Authorization Category I Operations and All Category II and III Operations.

2. When TDZ and/or CL lighting become inoperative on a standard CAT II instrument approach, the certificate holder is authorized to conduct SA CAT II operations.

5−3−7. NAVAID CONDITIONS

FIG 5−3−1 NAVAIDs

…NAV VOR 090−180 BEYOND 25NM SFC−5000FT, 270−300 BEYOND 25NM SFC−5000FT, 300−360 BEYOND 35NM SFC−4000FT UNUSABLE…

See Appendix A for examples.

a. Originate a NOTAM D for commissioning, decommissioning, outages, or unmonitored status of radio navigation aids (60 minutes or more and 30 minutes or more for RADAR) that are part of the NAS. The NOTAM must be canceled by the originator.

b. Restrictions to NAVAIDs are normally published by segment; for example, 020-055 degree radials. To correct a given segment, cancel the original NOTAM and issue a completely new NOTAM. Add “PLUS SEE (publication)” when other restrictions to the NAVAID are published. The absence of this statement from the NOTAM indicates that all other restrictions have been canceled.

NOTE− When required, NDB restrictions have the phrase “bearing to”, while VOR restrictions use the phrase “radials from.”

c. Instrument Landing Systems (ILS).

NAVAID NOTAMs 5−3−2

FIG 5−3−2

ILS

…NAV ILS RWY 12 LOC UNUSABLE BEYOND 4DEG RIGHT OF COURSE…

1. Distinguish components of an ILS from non-precision approach NAVAIDs by preceding the component with “ILS” followed by “RWY” and the runway number (including single ILS airports). Use the term “COURSE” when describing radio navigation aid restrictions. Back Course and Coupled Approach NOTAMs are FDC.

2. Excessive snow and ice accumulation near the glide slope antennas may affect facility performance to the extent that it is inoperative. When this occurs, Technical Operations personnel at the glide slope location are required to initiate appropriate NOTAM D action. Technical operations personnel must monitor snow conditions to determine when conditions permit use of the glide slope and initiate action to cancel the NOTAM. Technical Operations and Aeronautical Information Services NOTAM Office make the determination when to issue an FDC NOTAM or NOTAM D, based on FAA JO 6750.49, Maintenance of Instrument Landing System (ILS) Facilities. Tech Ops issues the NOTAM D and AIS NOTAM Office issues the FDC.

d. Simplified directional facility.

e. Localizer type directional aid for the airport.

f. VOR/DME.

g. VORTAC.

1. VORTAC (all components, VOR/TACAN/AZM/DME).

2. VOR out of service (TACAN/AZM/DME/ operational).

3. DME out of service (VOR/TACAN/AZM operational).

4. TACAN azimuth out of service (VOR/DME operational).

h. VOT (VOR Test Facility).

i. VOR Receiver Checkpoint.

j. TVOR.

1. TVORs serving one airport, and not associated with airway structure, must have NOTAMs issued using the associated airport identifier as the affected facility.

2. TVORs serving more than one airport, or associated with airway structure, must have NOTAMs issued using the TVOR identifier as the affected facility.

k. NDB outages:

1. Terminal NDBs. Those NDBs located on or serving only that airport must have NOTAMs issued using the associated airport as the affected facility.

2. If an NDB serves more than one airport, or associated with an airway route structure, issue a NOTAM using the identifier of the NDB as the affected facility.

l. LOM outages.

1. LOM serving one airport must be issued with the three−letter identifier of the airport as the location identifier.

2. LOM serving more than one airport must be issued under the three-letter identifier of each airport that it serves. This procedure may require coordination with other facilities.

NAVAID NOTAMs 5−3−3

m. NAVAID identification change.

EXAMPLE− …NAV VORTAC ID CHANGED TO VHP…

5−3−8. SATELLITE BASED SYSTEMS

See Appendix A for examples.

a. Global Positioning System (GPS).

1. All global positioning system pseudo−random noise (PRN) GPS satellite outages will be reported directly to the USNOF by the Air Force Space Command (AFSPACECOM) monitoring facility. The USNOF will issue NOTAMs under the accountability “GPS” with a location of “GPS.” When these NOTAMs get distributed internationally, the USNOF changes the designator “KNMH.”

NOTE− GPS operations are included in the Aeronautical Information Manual.

2. All GPS interference testing NOTAMs will be reported to the USNOF by Technical Operations ATC Spectrum Engineering Services, Spectrum Assignment and Engineering Services. The USNOF will format NOTAMs under the accountability “GPS” with a location identifier of the associated center.

b. Wide Area Augmentation System (WAAS). WAAS area-wide NOTAMs are originated when WAAS assets are out of service and impact the service area. The term “MAY NOT BE AVBL” indicates that due to ionospheric conditions, lateral guidance may still be available when vertical guidance is unavailable. Under certain conditions, both lateral and vertical guidance may be unavailable. USNOF distributes these as FDC NOTAMs when a WAAS asset failure affects a large area, or as Center NOTAMs if all airports with RNAV approaches within a center’s boundary do not have WAAS availability. USNOF utilizes templates provided by Technical Operations, WAAS Operations. All events must reflect an effective time and expiration time.

1. Unscheduled loss of signal or service.

2. Ionosphere storm conditions.

3. Scheduled loss of signal or service.

c. Upon receipt of notification of satellite/surveillance system interference issue the following NOTAM

1. GPS interference:

2. Automatic Dependent Surveillance and affected components, including Wide Area Multilateration Outage

(a) Localized Service Outage for the affected airport

(b) Large Service Outages affecting an Air Route Traffic Control Center area(s)

(1) Single service outage – for large area

(2) Multiple service outages

(c) Large Service Outages affecting several Air Route Traffic Control Center areas

d. Ground Based Augmentation System (GBAS). Originate NOTAMs when the GBAS is out of service for maintenance reasons or predicted to be out of service. GBASs are operated by non-federal service providers, currently IAH and EWR.

1. Unscheduled loss of signal or service.

2. Predicted loss of signal or service.

5−3−9. HOURS OF OPERATION

Changes in the hours of operation of a NAVAID due to other than seasonal daylight time changes.

NAVAID NOTAMs 5−3−4

Chapter 5. NOTAM Criteria › Section 4. Communications Outlets NOTAMs

Section 4. Communications Outlets NOTAMs

5−4−1. GENERAL

Technical Operations personnel must ensure the origination of NOTAM D concerning communication outlets for which they are responsible.

5−4−2. REPORTING COMMUNICATIONS OUTLET MALFUNCTIONS

Known or reported malfunctions of a communication outlet must be reported to Technical Operations or appropriate personnel.

5−4−3. COMMUNICATION OUTLET CONDITIONS

FIG 5−4−1

COM

…COM REMOTE TRANS/REC 126.25, 131.25 OUT OF SERVICE…

Originate a NOTAM for conditions pertaining to the operation of communications outlets that are part of the NAS when an outage occurs or when a scheduled shutdown is expected as follows:

a. Use a comma to separate multiple frequencies.

b. Commissioning, decommissioning, outage, or (un)availability of communications outlets for the following:

1. All published ATC frequencies and all communication frequencies will be issued with the affected frequency when out of service.

(a) Remote Communication Outlets associated with an airport or NAVAID.

(b) Remote Communication Outlets NOT associated with an airport or NAVAID.

2. If several frequencies are out, but one is still operating, issue the out-of-service frequencies in one NOTAM.

(a) Remote Communication Outlets associated with an airport or NAVAID.

(b) Remote Communication Outlets NOT associated with an airport or NAVAID.

Communications Outlets NOTAMs 5−4−1

Chapter 5. NOTAM Criteria › Section 5. Services NOTAMs

Section 5. Services NOTAMs

5−5−1. GENERAL

FIG 5−5−1

Services

…SVC POTOMAC APP OUT OF SERVICE. RICHMOND CLASS C SERVICE NOT AVBL. CTC XXXXXXX ON XXX.XX…

a. Technical Operations personnel must ensure the origination of NOTAM D concerning the malfunction or degradation of FAA maintained systems and/or equipment.

b. When notified, Technical Operations and Air Traffic personnel must ensure the origination of NOTAM D concerning changes to air traffic services and capabilities, for which they are responsible.

5−5−2. CHANGES TO PUBLISHED SERVICES

a. The party that issues the NOTAM is responsible for formatting the information correctly.

b. Originate a NOTAM for conditions pertaining to the following conditions:

1. Commissioning, decommissioning, or outage of TWRs, APPs, RAPCONs, FSSs, and ARTCCs that are part of the NAS.

2. Hazardous In flight Weather Advisory Service (HIWAS). HIWAS is considered a service because it is broadcast and not a two-way communication system.

(a) Outage of HIWAS service outlets must be advertised as a separate NOTAM for each outlet.

(b) Commissioning or non-availability of a new HIWAS outlet.

3. Automatic Terminal Information Service (ATIS).

4. Automatic Flight Information Service.

5. Automated Universal Communication (AUNICOM). AUNICOMs have portions that are automatically broadcast along with the voice recordings. When these functions are out of service or not available, issue a NOTAM.

5−5−3. HOURS OF OPERATION

Disseminate the following conditions as NOTAMs:

a. Change in the hours of operation of an air traffic control facility or service. Tower hours of operation use the airport as the location identifier; for approach controls, since they cover a larger area, use the associated ARTCC(s). Approach controls located within multiple ARTCC airspace must have a separate NOTAM for each ARTCC. When needed, add which class of services is not available and whom to contact.

Services NOTAMs 5−5−1

b. Establishment of a temporary air traffic control tower. Specify the frequency(ies) to be used and, if necessary, the type of service provided with each frequency.

c. Total failure of an air traffic facility (for example, loss of communications, NAVAID monitoring, etc.). Provide the class of service that are not available; the class of services to expect, and, if needed, who to contact for services.

1. Air route traffic control centers (ARTCC).

2. Approach control.

3. Flight service stations. FSS covering a large Flight Plan Area use the ARTCC as the location identifier; for FSS with a small Flight Plan Area use the airport as the location identifier. Flight Plan Areas located within multiple ARTCC airspace must have a separate NOTAM for each ARTCC.

(a) Covering a large Flight Plan area

(b) Covering a small Flight Plan area of 5NM or less.

(c) Flight Plan area covering 2 or more centers

4. Air traffic control towers.

d. Traffic Management Program Alerts.

1. When requested by the associated arrival ARTCC TMU, issue an alerting NOTAM for each airport where an arrival/departure reservation is required. NOTAMs should be in the self-canceling format whenever possible.

2. When a flow control message (for example, arrival delays, ground stops, ground delays, airborne holding, etc.) is received from the Air Traffic Control System Command Center (ATCSCC), the tie-in FSS for the affected airport(s) must issue a NOTAM(s) in the self-canceling format.

5−5−4. WEATHER AND WEATHER REPORTING EQUIPMENT

a. Technical Operations personnel, responsible for system monitoring, must ensure the origination of NOTAMs on Federal AWOS systems as follows:

1. Total system failure (which includes date-time code failures).

2. Altimeter setting is reported as “missing.” AWOS weather reports will be disseminated with missing report elements including altimeter settings. The letter “M” will appear on the operator’s terminal in place of any missing elements. No report will be disseminated when there is a total system failure.

3. Inaccurate/unreliable sensor readings.

4. When malfunctions or discrepancies are reported to a facility, they must be verified by any of the following methods:

(a) A certified observer, airport manager, or fixed base operator at the observation site.

Continue reading ↓ 120 of 258 passages shown