Radar Vectors
FAA Order Cancelled Issued May 17, 2021 AJR-B 638 pages Copy saved Nov 18, 2026

Order JO 7110.10BB Flight Services

This document is cancelled. Cancelled by JO 7110.10CC. Check the official source before relying on it.

Official source ↗ Open PDF

Text read by OCR from a scanned file (7 of 638 pages). Check the original, as some words may be misread.

FAA Order JO 7110.10BB, Flight Services, effective June 17, 2021

ORDER JO 7110.10%% Air Traffic Organization Policy

Effective Date:

-XQH1,20

SUBJ: Flight Services

This order prescribesairtraffic controlproceduresandphraseologyfor use by personnel providing air traffic control services. Controllers are requiredto be familiar withthe provisions ofthis order that pertaintotheir operationalresponsibilitiesandto exercisejudgment ifthey encounter situations not coveredby it.

Digitally signed by VIRGINIA T VIRGINIA T BOYLE Date: 2021.05.14 BOYLE 15:25:02 -04'00' 9LUJLQLD%R\OH Vice President, SystemOperations Services Air Traffic Organization

Distribution: Electronic Initiated By: AJR-0 Vice President, System Operations Services

RECORD OF CHANGES DIRECTIVE NO. JO 7110.10BB

CHANGE

TO BASIC

SUPPLEMENTS

OPTIONAL

CHANGE

TO BASIC

SUPPLEMENTS

OPTIONAL

FAA Form 1320−5 (6−80) USE PREVIOUS EDITION

FAA Order JO 7110.10BB, Flight Services, effective June 17, 2021 › Explanation of Changes - Basic

Flight Services Explanation of Changes

Basic

Direct questions through appropriate facility/service center office staff

to the Office of Primary Interest (OPI)

a. 2−1−4. WEATHER DISPLAY PRODUCTS

2−1−8. LOGGING OF PILOT BRIEFINGS

3−3−5. ROUTINE RADIO CONTACTS 4−1−3. OBTAINING INFORMATION 4−1−4. COORDINATION 4−2−5. ALERTING CONTROL FACILITY

The changes to Chapter 2 and 3 clarify that certain procedures apply only to Alaska. Changes to Chapter 4 provide updated guidance on the handling of emergencies. FIG 2−1−2 is replaced to be consistent with a newer version as found in the Aviation Weather Handbook.

b. 4−2−15. SUSPICIOUS UNMANNED AIRCRAFT SYSTEMS (UAS) ACTIVITY

This change adds paragraph 4−2−15, Suspicious Unmanned Aircraft Systems (UAS) Activity, to FAA Order JO 7110.10, Flight Services. The paragraph directs personnel to notify the supervisor or controller−in−charge upon observation of suspicious UAS activities. This change harmonizes procedures found in FAA Order JO 7110.65, Air Traffic Control, paragraph 2−1−26; FAA Order JO 7610.4, Special Operations, paragraph 7−3−1; FAA Order JO 7210.3, Facility Operations and Administration, paragraphs 2−1−30 and 2−1−32; and FAA Order JO 7210.632, Air Traffic Organization Occurrence Reporting, Appendix A.

c. 5−1−1. COMMUNICATIONS SERVICE

5−3−2. NOTIFYING ARTCC 5−5−1. SPECIAL MILITARY FLIGHTS 5−6−1. AIRCRAFT MOVEMENT INFORMATION SERVICES (AMIS) WITHIN AN ADIZ−IFR

5−6−2. AMIS WITHIN AN ADIZ−DVFR

Changes made to Chapter 5 are to update communications information (5−1−1); add TBL 5−3−1 to indicate flight plan lock−out times by ARTCC and

clarify entry times for flight plans into operating systems; remove obsolete procedures (5−5−1); and clarify current procedures (5−3−2). Paragraphs 5−6−1 and 5−6−2 were changed to reflect discontinuation of the acronym Aircraft Movement Information Services (AMIS).

d. 5−1−2. FLIGHT PLANS

5−1−3. FLIGHT PLAN DATA 5−1−6. IFR/VFR/DVFR FLIGHT PLAN RECORDING

5−2−1. FLIGHT PLAN RECORDING 5−2−2. OUTBOUNDS DEPARTING FROM OUTSIDE FLIGHT PLAN AREA

5−3−1. IFR FLIGHT PLANS 5−3−3. IFR FLIGHT PLAN CONTROL MESSAGES

5−3−4. IFR FLIGHT PLAN CONTROL MESSAGE FORMAT

5−4−2. DEPARTURE REPORT MESSAGE 5−4−3. ACKNOWLEDGING NUMBERED MESSAGES

5−4−4. FLIGHT NOTIFICATION MESSAGE

5−4−5. SUSPENDING FLIGHT NOTIFICATION MESSAGES

5−4−6. ACKNOWLEDGING FLIGHT NOTIFICATION MESSAGES

5−4−8. MAJOR FLIGHT PLAN CHANGES FROM EN ROUTE AIRCRAFT

5−4−9. CHANGE IN ETA 5−4−10. FLIGHT PLAN CLOSURE 5−5−4. MESSAGE HANDLING 5−6−3. FORWARDING DVFR INFORMATION

6−1−8. ADDRESSING MESSAGES 6−1−9. FLIGHT PLAN FORMS AND INSTRUCTIONS

6−1−10. ICAO ATS MESSAGE FORMAT 6−4−2. INBOUNDS FROM CANADA 6−4−3. OUTBOUNDS TO CANADA 6−4−4. OUTBOUNDS TO CANADA

Explanation of Changes E of C−1

DEPARTING FROM OUTSIDE FLIGHT PLAN AREA

6−4−5. IFR FLIGHT PLANS DEPARTING CANADIAN AIRPORTS

Appendix A. ICAO FLIGHT PLANS Appendix B. FSS FORMS Appendix C. FAA FORMS Appendix D. SERVICE B MESSAGES FORMATS

Appendix E. DOMESTIC FLIGHT DATA (LEGACY)

Appendix F. INTERNATIONAL OPERATIONS (LEGACY)

The following changes are required to align the order with current operational processes. These changes also support the standardized use of FAA Form 7233−4, International Flight Plan. These changes also inform stakeholders that the legacy procedures of FAA Form 7233−1 may be employed by users who file civilian stereo route and military flight plans.

e. 5−2−1. FLIGHT PLAN RECORDING

This change to JO 7110.10 provides guidance for flight data personnel and dispatchers on how to process a flight plan for an aircraft whose call sign begins with a number.

f. 6−1−12. AIR MOBILE SERVICE (AMS)

This change reflects the removal of the term Aeronautical Radio, Incorporated (ARINC) and reflects the addition of new communication relay call signs due to corporate changes in the company name.

g. 7−2−2. QALQ

7−2−3. ACTION BY DEPARTURE STATION ON RECEIPT OF QALQ

7−4−2. ACTION UPON RECEIPT OF ALNOT

This change updates paragraph 7−2−2 with an editorial change and adds a new reference to a preceding chapter. The change to paragraph 7−2−3 clarifies procedures used for facilities with a shared database, while the change to paragraph 7−4−2 expands the broadcast area during the Alert Notice (ALNOT) stage of search and rescue.

h. 8−1−2. SCHEDULED TRANSMISSION TIMES

8−2−4. PIREP DISPLAY 8−2−11. PIREP HANDLING 8−2−14. PIREP FORMAT 8−3−1. GENERAL 8−3−2. LEVELS FORECAST 8−4−2. TERMINAL AERODROME FORECAST SCHEDULES

8−7−1. GENERAL 8−7−2. DISTRIBUTION

This change to Chapter 8 clarifies that certain procedures now apply only to Alaska, brings the order into compliance with recent changes to National Weather Service instructions, and eliminates obsolete procedures.

i. 9−1−1. AIRPORT LIGHTING

9−1−5. APPROACH LIGHTING SYSTEM INTENSITY SETTING (ALS)

9−1−9. MEDIUM INTENSITY APPROACH LIGHTING SYSTEM WITH RUNWAY ALIGNMENT INDICATOR LIGHTS (MALSR)/OMNIDIRECTIONAL APPROACH LIGHTING SYSTEM (ODALS)

9−1−12. HIGH INTENSITY RUNWAY, RUNWAY CENTERLINE (RCLS), AND TOUCHDOWN ZONE LIGHTS (TDZL)

9−1−15. RUNWAY END IDENTIFIER LIGHTS (REIL)

9−1−17. VISUAL APPROACH SLOPE INDICATORS (VASIs)

9−1−18. VISIBILITY AIDS – GENERAL 9−1−19. RVR/RVV

This change to Chapter 9 clarifies procedures that are currently being performed in Alaska with respect to airport lighting and visibility aids. This change also adds ODALS to airport lighting instructions and removes Runway Visibility Value (RVV), which is no longer used.

j. 10−1−1. PURPOSE

10−1−4. MESSAGE INITIATION

This change to Chapter 10 clarifies the procedure for interphone communication at a particular position. The title of paragraph 10−1−1 is changed to more clearly reflect the contents of the paragraph.

E of C−2 Explanation of Changes

k. 11−1−8. WEATHER PHRASEOLOGY

11−1−9. WEATHER REMARKS 11−1−12. WINDS AND TEMPERATURES ALOFT FORECAST (FB)

11−1−15. AIRCRAFT IDENTIFICATION 11−1−16. DESCRIPTION OF AIRCRAFT TYPES

11−1−18. AIRWAYS AND ROUTES 11−1−19. NAVAID TERMS 12−1−3. GROUP CODES

This change to Chapter 11 updates paragraphs 11−1−8, 11−1−15, 11−1−16, 11−1−18, 11−1−19, and TBL 11−1−1 to harmonize with FAA Order JO 7110.65 and bring consistency among FAA air traffic directives. Paragraph 11−1−12 is changed to allow for

a more narrow interpolation of wind direction, depending on the user’s operating system. The change to Chapter 12 is to update group codes used for mass disseminated messages.

l. Editorial Changes

The publication schedule chart is expanded. A reference to basic VFR weather minimums is added to paragraph 3−5−2. Finally, minor fixes are made throughout the document.

m. Entire Publication

Additional editorial/format changes were made where necessary. Revision bars were not used because of the insignificant nature of these changes.

Explanation of Changes E of C−1

Change 1, effective December 2, 2021

Digitally signed by

Date: 2021.10.29 07:36:01 -04'00'

CHANGE

U.S. DEPARTMENT OF TRANSPORTATION JO 7110.10BB

CHG 1 FEDERAL AVIATION ADMINISTRATION

Air Traffic Organization Policy Effective Date: December 2, 2021

SUBJ: Flight Services

1. Purpose of This Change. This change transmits revised pages to Federal Aviation Administration Order JO 7110.10BB, Flight Services, and the Briefing Guide.

2. Audience. This change applies to select offices in Washington headquarters, service area offices, the William J. Hughes Technical Center, the Mike Monroney Aeronautical Center, and to all air traffic field facilities, international aviation field offices, and the interested aviation public.

3. Where Can I Find This Change? This change is available on the FAA website at http://faa.gov/air_traffic/publications and http://employees.faa.gov/tools_resources/orders_notices/.

4. Explanation of Policy Change. See the Explanation of Changes attachment which has editorial corrections and changes submitted through normal procedures. The Briefing Guide lists only new or modified material, along with background.

5. Distribution. This change is distributed to select offices in Washington headquarters, service area offices, the William J. Hughes Technical Center, the Mike Monroney Aeronautical Center, and to all air traffic field facilities, international aviation field offices, and the interested aviation public.

6. Disposition of Transmittal. Retain this transmittal until superseded by a new basic order.

7. Page Control Chart. See the page control chart attachment.

VIRGINIA T VIRGINIA T BOYLE BOYLE Virginia Boyle Vice President, System OperationV Services Air Traffic Organization

Distribution: Electronic Initiated By: AJR-0 Vice President, System Operations Services

Change 1, effective December 2, 2021 › Explanation of Changes - Change 1

12/2/21 JO 7110.10BB CHG 1

Flight Services Explanation of Changes

Change 1

Direct questions through appropriate facility/service center office staff

to the Office of Primary Interest (OPI)

a. 1−3−2 PRIORITY

2−2−1 CONDUCT OF STANDARD BRIEFING

3−6−1 AUTOMATIC FLIGHT INFORMATION SERVICE (AFIS)

This editorial change complies with the Federal Women’s Program (FWP) suggestions. The acronym NOTAM is updated from Notice to Airmen to the more applicable term Notice to Air Missions, which is inclusive of all aviators and missions.

b. 2−2−1. CONDUCT OF STANDARD BRIEFING

3−3−5. ROUTINE RADIO CONTACTS 8−6−1. GENERAL 8−6−2. DISTRIBUTION

This change reflects new National Weather Service (NWS) terminology for NWS Storm Prediction Center (SPC)−issued Aviation Watch Notification Messages (SAW), formerly known as Alert Severe Weather Watch Bulletins (AWW).

c. Editorial Changes

Editorial changes include the replacement of Appendices A and B to match the information in the Aeronautical Information Manual (AIM).

d. Entire Publication

Additional editorial/format changes were made where necessary. Revision bars were not used because of the insignificant nature of these changes.

Explanation of Changes E of C−1

Digitally signed by

Date: 2022.04.13 10:41:39 -04'00'

CHANGE

U.S. DEPARTMENT OF TRANSPORTATION JO 7110.10BB

Change 2, effective May 19, 2022

CHG 2 FEDERAL AVIATION ADMINISTRATION

Air Traffic Organization Policy Effective Date:

May 19, 2022

SUBJ: Flight Services

1. Purpose of This Change. This change transmits revised pages to Federal Aviation Administration Order JO 7110.10BB, Flight Services, and the Briefing Guide.

2. Audience. This change applies to select offices in Washington headquarters, service area offices, the William J. Hughes Technical Center, the Mike Monroney Aeronautical Center, and to all air traffic field facilities, international aviation field offices, and the interested aviation public.

3. Where Can I Find This Change? This change is available on the FAA website at http://faa.gov/air_traffic/publications and http://employees.faa.gov/tools_resources/orders_notices/.

4. Explanation of Policy Change. See the Explanation of Changes attachment which has editorial corrections and changes submitted through normal procedures. The Briefing Guide lists only new or modified material, along with background.

5. Distribution. This change is distributed to select offices in Washington headquarters, service area offices, the William J. Hughes Technical Center, the Mike Monroney Aeronautical Center, and to all air traffic field facilities, international aviation field offices, and the interested aviation public.

6. Disposition of Transmittal. Retain this transmittal until superseded by a new basic order.

7. Page Control Chart. See the page control chart attachment.

VIRGINIA T VIRGINIA T BOYLE BOYLE Virginia Boyle Vice President, System OperationV Services Air Traffic Organization

Distribution: Electronic Initiated By: AJR-0 Vice President, System Operations Services

Change 2, effective May 19, 2022 › Explanation of Changes - Change 2

5/19/22 JO 7110.10BB CHG 2

Flight Services Explanation of Changes

Change 2

Direct questions through appropriate facility/service center office staff

to the Office of Primary Interest (OPI)

a. 3−4−3. AIRPORT ADVISORY/RAIS b. Editorial Changes ELEMENTS AND PHRASEOLOGY The SATVOICE (Iridium) filing code M2 is replaced with M3 in TBL A−11 in Appendix A. This change instructs flight service specialists when issuing airport advisories to include information c. Entire Publication about known, observed, or pilot−reported unmanned Additional editorial/format changes were made aircraft (UA) activity when proximity warrants it. where necessary. Revision bars were not used because of the insignificant nature of these changes.

Explanation of Changes E of C−1

Change 3, effective November 3, 2022

Alyce Hood-Fleming

HOOD-FLEMING Date: 2022.09.30 15:43:04 -04'00'

CHANGE

U.S. DEPARTMENT OF TRANSPORTATION JO 7110.10BB

CHG 3 FEDERAL AVIATION ADMINISTRATION

Air Traffic Organization Policy Effective Date: November 3, 2022

SUBJ: Flight Services

1. Purpose of This Change. This change transmits revised pages to Federal Aviation Administration Order JO 7110.10BB, Flight Services, and the Briefing Guide.

2. Audience. This change applies to select offices in Washington headquarters, service area offices, the William J. Hughes Technical Center, the Mike Monroney Aeronautical Center, and to all air traffic field facilities, international aviation field offices, and the interested aviation public.

3. Where Can I Find This Change? This change is available on the FAA website at http://faa.gov/air_traffic/publications and http://employees.faa.gov/tools_resources/orders_notices/.

4. Explanation of Policy Change. See the Explanation of Changes attachment which has editorial corrections and changes submitted through normal procedures. The Briefing Guide lists only new or modified material, along with background.

5. Distribution. This change is distributed to select offices in Washington headquarters, service area offices, the William J. Hughes Technical Center, the Mike Monroney Aeronautical Center, and to all air traffic field facilities, international aviation field offices, and the interested aviation public.

6. Disposition of Transmittal. Retain this transmittal until superseded by a new basic order.

7. Page Control Chart. See the page control chart attachment.

Digitally signed by ALYCE ALYCE HOOD­ FLEMING

Acting Vice President, System OperationV Services Air Traffic Organization

Distribution: Electronic Initiated By: AJR-0 Vice President, System Operations Services

Change 3, effective November 3, 2022 › Explanation of Changes - Change 3

11/3/22 JO 7110.10BB CHG 3

Flight Services Explanation of Changes

Change 3

Direct questions through appropriate facility/service center office staff

to the Office of Primary Interest (OPI)

a. 5−3−2. NOTIFYING ARTCC

5−4−7. MAJOR FLIGHT PLAN CHANGES FROM EN ROUTE AIRCRAFT

APPENDIX A. FAA FORM 7233−4 − INTERNATIONAL FLIGHT PLAN

This change corrects the transmit flight plan time from 23 to less than 22½ hours before the proposed departure time. This change also clarifies instructions for flight service specialists in processing a military change of destination and other major flight plan changes from en route aircraft.

b. 6−1−8. ADDRESSING MESSAGES

This change adds instructions for users addressing flight plans and associated messages for instrument flight rules (IFR) flights and mixed IFR/VFR flights entering, overflying, or departing the Eurocontrol Integrated Initial Flight Plan Processing System (IFPS) Zone.

c. APPENDIX A. FAA FORM 7233−4 − INTERNATIONAL FLIGHT PLAN

This change removes existing instructions allowing alternate use of NAV/ to indicate Area Navigation (RNAV) capability to resolve incompatibility with Required Navigation Performance (RNP) routing. It adds instructions for RNP Standard Instrument Departures (SIDs) and Standard Terminal Arrival Routes (STARs), which are being added to the NAS (for example, see the KSNA STAYY SID). Removes the legacy use of NAV/ for RNAV capability to avoid the NAV/ information overriding RNP capability filed in PBN/. Because ICAO guidance is moving towards use of standardized, unambiguous codes M1 and M2 for the two variations of RNP 2, the information relating to Australia’s practice is removed from the table.

d. Entire Publication

Additional editorial/format changes were made where necessary. Revision bars were not used because of the insignificant nature of these changes.

Explanation of Changes E of C−1

Table of Contents

11/3/22 JO 7110.10BB CHG 3

Table of Contents

Chapter 1. General

Section 1. Introduction

Paragraph Page 1−1−1. PURPOSE OF THIS ORDER … 1−1−1 1−1−2. AUDIENCE … 1−1−1 1−1−3. WHERE TO FIND THIS ORDER … 1−1−1 1−1−4. WHAT THIS ORDER CANCELS … 1−1−1 1−1−5. EXPLANATION OF CHANGES … 1−1−1 1−1−6. EFFECTIVE DATES AND SUBMISSIONS FOR CHANGES … 1−1−1 1−1−7. DELIVERY DATES … 1−1−1 1−1−8. RECOMMENDATIONS FOR PROCEDURAL CHANGES … 1−1−1 1−1−9. SUBSCRIPTION INFORMATION … 1−1−2 1−1−10. DISTRIBUTION … 1−1−2

Section 2. Terms of Reference

1−2−1. WORD MEANINGS … 1−2−1 1−2−2. NOTES … 1−2−1 1−2−3. EXAMPLES … 1−2−1 1−2−4. PHRASEOLOGY … 1−2−1 1−2−5. ABBREVIATIONS … 1−2−1 1−2−6. JO 7110.10 CHANGES … 1−2−1 1−2−7. SYSTEM INSTRUCTIONS … 1−2−2

Section 3. Responsibility

1−3−1. PROCEDURAL APPLICATIONS … 1−3−1 1−3−2. DUTY PRIORITY … 1−3−1 1−3−3. DUTY FAMILIARIZATION AND TRANSFER OF POSITION RESPONSIBILITY 1−3−1

Chapter 2. Pilot Briefing

Section 1. General

2−1−1. DEFINITION … 2−1−1 2−1−2. PRE-DUTY REQUIREMENTS … 2−1−1 2−1−3. PREFLIGHT BRIEFING DISPLAY … 2−1−1 2−1−4. WEATHER DISPLAY PRODUCTS … 2−1−1 2−1−5. FORECASTS, WARNINGS, AND ADVISORIES … 2−1−3 2−1−6. UNAVAILABILITY OF DATA … 2−1−3 2−1−7. TYPE OF BRIEFING TO BE CONDUCTED … 2−1−3 2−1−8. LOGGING PILOT BRIEFINGS … 2−1−3

Section 2. Preflight Pilot Briefing

2−2−1. CONDUCT OF STANDARD BRIEFING … 2−2−1 2−2−2. CONDUCT OF ABBREVIATED BRIEFING … 2−2−2 2−2−3. CONDUCT OF OUTLOOK BRIEFING … 2−2−3

Table of Contents i

JO 7110.10BB CHG 3 11/3/22

Chapter 3. Inflight Services

Section 1. General

Paragraph Page 3−1−1. INFLIGHT SERVICES … 3−1−1 3−1−2. OPERATIONAL PRIORITY … 3−1−1 3−1−3. INFLIGHT WEATHER BRIEFING … 3−1−1 3−1−4. INFLIGHT EQUIPMENT MALFUNCTIONS … 3−1−2 3−1−5. AIRCRAFT REPORTED MALFUNCTIONS … 3−1−2 3−1−6. NAVAID FLIGHT CHECK … 3−1−3

Section 2. Data Recording

3−2−1. TYPES OF DATA RECORDED … 3−2−1 3−2−2. METHODS OF RECORDING DATA … 3−2−1 3−2−3. IFR/VFR/DVFR FLIGHT PLAN RECORDING … 3−2−2 3−2−4. FLIGHT PROGRESS STRIPS (FAA FORMS 7230-21 AND 7233-5) … 3−2−2 3−2−5. FLIGHT PROGRESS STRIPS AND ENTRY DATA … 3−2−2 3−2−6. AIRCRAFT CONTACTS … 3−2−6

Section 3. Radio Communications

3−3−1. FREQUENCY USE … 3−3−1 3−3−2. AUTHORIZED TRANSMISSIONS … 3−3−1 3−3−3. RADIO MESSAGE FORMAT … 3−3−1 3−3−4. ABBREVIATED TRANSMISSION … 3−3−2 3−3−5. ROUTINE RADIO CONTACTS … 3−3−2 3−3−6. RADIO COMMUNICATIONS TRANSFER … 3−3−4 3−3−7. ATC CLEARANCES, ADVISORIES, OR REQUESTS … 3−3−4 3−3−8. DEPARTURE REPORTS … 3−3−4 3−3−9. IFR FLIGHT PROGRESS REPORTS … 3−3−5 3−3−10. ARRIVAL/MISSED APPROACH REPORTS … 3−3−5 3−3−11. NONDELIVERY OF MESSAGES … 3−3−5 3−3−12. BROADCAST (BLIND TRANSMISSION) OF MESSAGES … 3−3−5 3−3−13. PENETRATION OF CLASS A AIRSPACE OR PROHIBITED/RESTRICTED AREA … 3−3−5

Section 4. Airport Advisory Services (Alaska Only)

3−4−1. TYPES OF AIRPORT ADVISORY SERVICES … 3−4−1 3−4−2. GENERAL … 3−4−1 3−4−3. AIRPORT ADVISORY/RAIS ELEMENTS AND PHRASEOLOGY … 3−4−2 3−4−4. CHARTS … 3−4−4 3−4−5. AUTHORIZED FREQUENCIES … 3−4−4 3−4−6. TRAFFIC CONTROL … 3−4−5 3−4−7. AIRCRAFT EQUIPMENT CHECKS … 3−4−5

Section 5. Special VFR Operation

3−5−1. AUTHORIZATION … 3−5−1 3−5−2. REQUESTS FOR SPECIAL VFR CLEARANCE … 3−5−1 3−5−3. VISIBILITY BELOW 1 MILE … 3−5−2 3−5−4. PREDESIGNED SPECIAL VFR CLEARANCES … 3−5−3

Table of Contents ii

11/3/22 JO 7110.10BB CHG 3

Section 6. Automatic Flight Information Service (AFIS) (Alaska Only)

Paragraph Page 3−6−1. AUTOMATIC FLIGHT INFORMATION SERVICE (AFIS) … 3−6−1

Chapter 4. Emergency Services

Section 1. General

4−1−1. EMERGENCY DETERMINATION … 4−1−1 4−1−2. RESPONSIBILITY … 4−1−1 4−1−3. OBTAINING INFORMATION … 4−1−1 4−1−4. COORDINATION … 4−1−1 4−1−5. PROVIDING ASSISTANCE … 4−1−2 4−1−6. RECORDING INFORMATION … 4−1−2 4−1−7. SAFE ALTITUDES FOR ORIENTATIONS … 4−1−2

Section 2. Operations

4−2−1. INFORMATION REQUIREMENTS … 4−2−1 4−2−2. FREQUENCY CHANGES … 4−2−1 4−2−3. AIRCRAFT ORIENTATION … 4−2−1 4−2−4. ALTITUDE CHANGE FOR IMPROVED RECEPTION … 4−2−1 4−2−5. ALERTING CONTROL FACILITY … 4−2−1 4−2−6. VFR AIRCRAFT IN WEATHER DIFFICULTY … 4−2−1 4−2−7. AIRCRAFT POSITION PLOTS … 4−2−2 4−2−8. EMERGENCY LOCATOR TRANSMITTER (ELT) SIGNALS … 4−2−2 4−2−9. EXPLOSIVE CARGO … 4−2−2 4−2−10. EXPLOSIVE DETECTION DOG HANDLER TEAMS … 4−2−2 4−2−11. INFLIGHT EQUIPMENT MALFUNCTIONS … 4−2−3 4−2−12. MINIMUM FUEL … 4−2−3 4−2−13. AIRCRAFT BOMB THREATS … 4−2−3 4−2−14. EMERGENCY SECURITY CONTROL OF AIR TRAFFIC (ESCAT) … 4−2−4 4−2−15. SUSPICIOUS UNMANNED AIRCRAFT SYSTEMS (UAS) ACTIVITY … 4−2−5

Section 3. ADF/VOR Orientation

4−3−1. ACTIONS REQUIRED … 4−3−1 4−3−2. GENERAL … 4−3−1 4−3−3. VOR ORIENTATION/VOR CROSS-FIX … 4−3−2 4−3−4. GUIDANCE TO AIRPORT … 4−3−4

Section 4. Global Positioning System (GPS)

4−4−1. ACTIONS REQUIRED … 4−4−1 4−4−2. GPS ORIENTATION … 4−4−1 4−4−3. GUIDANCE TO AIRPORT … 4−4−1

Chapter 5. Flight Data

Section 1. General

5−1−1. COMMUNICATIONS SERVICE … 5−1−1 5−1−2. FLIGHT PLANS … 5−1−1

Table of Contents iii

JO 7110.10BB CHG 3 11/3/22

Paragraph Page 5−1−3. FLIGHT PLAN DATA … 5−1−1 5−1−4. TYPES OF DATA RECORDED … 5−1−2 5−1−5. METHODS OF RECORDING DATA … 5−1−2 5−1−6. IFR/VFR/DVFR FLIGHT PLAN RECORDING … 5−1−3 5−1−7. PART-TIME FSS CLOSURE ACTION … 5−1−3 5−1−8. TELEPHONE REQUESTS FOR ATC CLEARANCES … 5−1−3

Section 2. Flight Plan Proposals

5−2−1. FLIGHT PLAN RECORDING … 5−2−1 5−2−2. OUTBOUNDS DEPARTING FROM OUTSIDE FLIGHT PLAN AREA … 5−2−3 5−2−3. FLIGHT PLANS WITH AREA NAVIGATION (RNAV) ROUTES IN DOMESTIC U.S. AIRSPACE … 5−2−3

Section 3. IFR Flight Plan Handling

5−3−1. IFR FLIGHT PLANS … 5−3−1 5−3−2. NOTIFYING ARTCC … 5−3−1 5−3−3. CONTROL MESSAGES FOR FORMATTED IFR FLIGHT PLANS … 5−3−2 5−3−4. IFR FLIGHT PLAN CONTROL MESSAGE FORMAT (FAA FORM 7233−4) … 5−3−3 5−3−5. ADDITIONAL MESSAGES … 5−3−7 5−3−6. COORDINATE RNAV ROUTES … 5−3−8

Section 4. Flight Plan Handling

5−4−1. FLIGHT PLAN ACTIVATION … 5−4−1 5−4−2. DEPARTURE REPORT MESSAGE … 5−4−1 5−4−3. DEPARTURE MESSAGE … 5−4−1 5−4−4. AWAITING MESSAGE ACKNOWLEDGMENT … 5−4−2 5−4−5. ACKNOWLEDGING FLIGHT NOTIFICATION MESSAGES … 5−4−3 5−4−6. ACTION BY ADDRESSEES … 5−4−3 5−4−7. MAJOR FLIGHT PLAN CHANGES FROM EN ROUTE AIRCRAFT … 5−4−3 5−4−8. CHANGE IN ETA … 5−4−3 5−4−9. FLIGHT PLAN CLOSURE … 5−4−4 5−4−10. MILITARY FLIGHTS TO/FROM U.S … 5−4−4

Section 5. Military Operations

5−5−1. SPECIAL MILITARY FLIGHTS … 5−5−1 5−5−2. MILITARY FOREIGN FLIGHTS … 5−5−1 5−5−3. USAF/USN UNDERGRADUATE PILOTS … 5−5−1 5−5−4. MESSAGE HANDLING … 5−5−1

Section 6. IFR/DVFR ADIZ Flight Plans

5−6−1. AIRCRAFT MOVEMENT SERVICES WITHIN AN ADIZ−IFR … 5−6−1 5−6−2. AIRCRAFT MOVEMENT SERVICES WITHIN AN ADIZ−DVFR … 5−6−1 5−6−3. FORWARDING DVFR INFORMATION … 5−6−1 5−6−4. STOPOVER DVFR FLIGHT PLANS … 5−6−1

Section 7. Non−Emergency Parachute Jumping

5−7−1. COORDINATION … 5−7−1 5−7−2. PRE-JUMP RADIO COMMUNICATIONS … 5−7−1

Table of Contents iv

11/3/22 JO 7110.10BB CHG 3

Chapter 6. International Operations

Section 1. Messages and Formats

Paragraph Page 6−1−1. GENERAL … 6−1−1 6−1−2. AIR TRAFFIC SERVICE (ATS) MESSAGES … 6−1−2 6−1−3. CATEGORIES OF MESSAGES … 6−1−2 6−1−4. SERVICE MESSAGES … 6−1−2 6−1−5. TRANSMISSION VIA NADIN … 6−1−2 6−1−6. TRANSMISSION OF ATS MESSAGES … 6−1−3 6−1−7. ORIGINATING MESSAGES … 6−1−4 6−1−8. ADDRESSING MESSAGES … 6−1−4 6−1−9. FLIGHT PLAN FORMS AND INSTRUCTIONS … 6−1−4 6−1−10. ICAO ATS MESSAGE FORMAT … 6−1−5 6−1−11. FLIGHT PLAN CHANGES AND CANCELLATIONS … 6−1−5 6−1−12. AIR MOBILE SERVICE (AMS) … 6−1−6 6−1−13. AIREPS (POSITION REPORTS) … 6−1−6 6−1−14. AIREP SPECIALS (ARS) … 6−1−9 6−1−15. ARTCC RELAY OF VFR MESSAGES … 6−1−9

Section 2. Customs Notification and ADIZ Requirements

6−2−1. FLIGHT PLAN/CUSTOMS REQUIREMENTS … 6−2−1 6−2−2. CUSTOMS REQUIREMENTS FOR INBOUND AND OUTBOUND AIRCRAFT . . 6−2−1 6−2−3. ADIZ REQUIREMENTS FOR INBOUND AND OUTBOUND AIRCRAFT … 6−2−1

Section 3. Alerting Service

6−3−1. GENERAL … 6−3−1 6−3−2. ALERTING PHASES … 6−3−1 6−3−3. ALERTING MESSAGE CONTENTS … 6−3−1

Section 4. Canadian Movement and Control Messages (Transborder

Flights Only)

6−4−1. GENERAL … 6−4−1 6−4−2. INBOUNDS FROM CANADA … 6−4−1 6−4−3. OUTBOUNDS TO CANADA … 6−4−1 6−4−4. OUTBOUNDS TO CANADA DEPARTING FROM OUTSIDE FLIGHT PLAN AREA … 6−4−2 6−4−5. IFR FLIGHT PLANS DEPARTING CANADIAN AIRPORTS … 6−4−2 6−4−6. SEARCH AND RESCUE MESSAGES … 6−4−2

Section 5. Mexican Movement and Control Messages (Transborder

Flights Only)

6−5−1. GENERAL … 6−5−1 6−5−2. INBOUNDS FROM MEXICO … 6−5−1 6−5−3. OUTBOUNDS TO MEXICO … 6−5−1

Table of Contents v

JO 7110.10BB CHG 3 11/3/22

Chapter 7. Search and Rescue (SAR) Procedures

Section 1. General

Paragraph Page 7−1−1. RESPONSIBILITY FOR SAR ACTION … 7−1−1 7−1−2. OVERDUE AIRCRAFT ON FLIGHT PLAN … 7−1−1 7−1−3. OVERDUE AIRCRAFT NOT ON FLIGHT PLAN … 7−1−1

Section 2. Overdue Aircraft Action

7−2−1. COMMUNICATIONS SEARCH … 7−2−1 7−2−2. QALQ … 7−2−1 7−2−3. ACTION BY DEPARTURE STATION ON RECEIPT OF QALQ … 7−2−1 7−2−4. CANCELLATION OF THE QALQ … 7−2−2

Section 3. Information Requests (INREQs)

7−3−1. INREQ … 7−3−1 7−3−2. ACTION UPON RECEIPT OF INREQ … 7−3−1 7−3−3. CANCELLATION OF INREQ … 7−3−1

Section 4. Alert Notices (ALNOTs)

7−4−1. ALNOT … 7−4−1 7−4−2. ACTION UPON RECEIPT OF ALNOT … 7−4−1 7−4−3. REPORTING ALNOT STATUS TO RCC … 7−4−1 7−4−4. CANCELLATION OF ALNOT … 7−4−2

Section 5. Other SAR Actions

7−5−1. CANADIAN TRANSBORDER … 7−5−1

Chapter 8. FAA Weather Services

Section 1. General

8−1−1. INTRODUCTION … 8−1−1 8−1−2. SCHEDULED TRANSMISSION TIMES (ALASKA ONLY) … 8−1−1 8−1−3. DISTRIBUTION … 8−1−1

Section 2. Pilot Weather Report (UA/UUA)

8−2−1. GENERAL … 8−2−1 8−2−2. PREPARATION FOR TRANSMISSION … 8−2−1 8−2−3. RESPONSIBILITY … 8−2−1 8−2−4. SOLICITING PIREPS … 8−2−1 8−2−5. DATA TO BE INCLUDED IN PIREPS … 8−2−2 8−2−6. REPORTING TURBULENCE IN PIREPS … 8−2−2 8−2−7. REPORTING ICING CONDITIONS IN PIREPS … 8−2−2 8−2−8. MEANS USED TO SOLICIT PIREPS … 8−2−2 8−2−9. PIREP CLASSIFICATION … 8−2−3 8−2−10. PIREP HANDLING … 8−2−3 8−2−11. OFFSHORE COASTAL ROUTES … 8−2−3 8−2−12. PIREP PREPARATION … 8−2−3

Table of Contents vi

11/3/22 JO 7110.10BB CHG 3

Paragraph Page 8−2−13. PIREP FORMAT … 8−2−4 8−2−14. PIREP ENCODING … 8−2−8

Section 3. Wind and Temperature Aloft Forecast (FB)

8−3−1. GENERAL … 8−3−1 8−3−2. LEVELS FORECAST … 8−3−1 8−3−3. DISTRIBUTION … 8−3−1

Section 4. Terminal Aerodrome Forecast (TAF)

8−4−1. GENERAL … 8−4−1 8−4−2. TERMINAL AERODROME FORECAST SCHEDULES … 8−4−1

Section 5. Aviation Surface Forecast/Aviation Cloud Forecast/Area

Forecast (FA)

8−5−1. GENERAL … 8−5−1 8−5−2. AREA FORECAST (FA) SCHEDULE … 8−5−1 8−5−3. AVIATION SURFACE FORECAST AND AVIATION CLOUD FORECAST ISSUANCE TIMES … 8−5−2

Section 6. Severe Weather Forecasts

8−6−1. GENERAL … 8−6−1 8−6−2. DISTRIBUTION … 8−6−1 8−6−3. CONVECTIVE OUTLOOK NARRATIVE (AC) … 8−6−1

Section 7. Flight Advisories (SIGMET/WS−Airmet/WA−Convective SIGMET/WST)

8−7−1. GENERAL … 8−7−1 8−7−2. DISTRIBUTION … 8−7−1

Section 8. Center Weather Advisory (CWA)

8−8−1. GENERAL … 8−8−1 8−8−2. CRITERIA … 8−8−1 8−8−3. DISTRIBUTION … 8−8−1

Chapter 9. Airport Lighting and Visibility Aids

(Alaska Only)

Section 1. General

9−1−1. AIRPORT LIGHTING … 9−1−1 9−1−2. OBSTRUCTION LIGHTS … 9−1−1 9−1−3. ROTATING BEACON … 9−1−1 9−1−4. APPROACH LIGHTS … 9−1−1 9−1−5. APPROACH LIGHTING SYSTEM INTENSITY SETTINGS (ALS) … 9−1−1 9−1−6. SEQUENCED FLASHING LIGHTS (SFL) … 9−1−1 9−1−7. RUNWAY EDGE LIGHTS … 9−1−2 9−1−8. CHANGING LIGHTED RUNWAYS … 9−1−2 9−1−9. MEDIUM INTENSITY APPROACH LIGHTING SYSTEM WITH RUNWAY ALIGNMENT INDICATOR LIGHTS (MALSR)/OMNIDIRECTIONAL APPROACH LIGHTING SYSTEM (ODALS) … 9−1−2

Table of Contents vii

JO 7110.10BB CHG 3 11/3/22

Paragraph Page 9−1−10. HIGH INTENSITY RUNWAY LIGHTS (HIRL) ASSOCIATED WITH MALSR . . 9−1−2 9−1−11. MEDIUM INTENSITY RUNWAY LIGHTS (MIRL) … 9−1−3 9−1−12. HIGH INTENSITY RUNWAY, RUNWAY CENTERLINE (RCLS), AND TOUCHDOWN ZONE LIGHTS (TDZL) … 9−1−3 9−1−13. HIRL CHANGES AFFECTING RVR … 9−1−3 9−1−14. HIGH SPEED TURNOFF LIGHTS … 9−1−3 9−1−15. RUNWAY END IDENTIFIER LIGHTS (REIL) … 9−1−3 9−1−16. TAXIWAY LIGHTS … 9−1−4 9−1−17. VISUAL APPROACH SLOPE INDICATORS (VASIS) … 9−1−4 9−1−18. VISIBILITY AIDS - GENERAL … 9−1−4 9−1−19. RVR … 9−1−5 9−1−20. OPERATION OF LANDING DIRECTION INDICATOR … 9−1−5

Chapter 10. Interphone Communications

Section 1. General

10−1−1. GENERAL … 10−1−1 10−1−2. INTERPHONE TRANSMISSION PRIORITIES … 10−1−1 10−1−3. PRIORITY INTERRUPTION … 10−1−1 10−1−4. MESSAGE INITIATION … 10−1−1 10−1−5. MESSAGE TERMINATION … 10−1−2

Chapter 11. Phraseology

Section 1. General

11−1−1. PURPOSE … 11−1−1 11−1−2. PHRASEOLOGY … 11−1−1 11−1−3. WORDS AND PHRASES … 11−1−1 11−1−4. ANNOUNCING MISSING ITEMS … 11−1−1 11−1−5. ICAO PHONETICS … 11−1−1 11−1−6. RELAY OF ATC COMMUNICATIONS … 11−1−2 11−1−7. EXPEDITIOUS COMPLIANCE … 11−1−2 11−1−8. WEATHER PHRASEOLOGY … 11−1−2 11−1−9. WEATHER REMARKS … 11−1−6 11−1−10. WEATHER ADVISORIES … 11−1−8 11−1−11. RADAR … 11−1−8 11−1−12. WINDS AND TEMPERATURES ALOFT FORECAST (FB) … 11−1−8 11−1−13. NUMBER USAGE … 11−1−9 11−1−14. FACILITY IDENTIFICATION … 11−1−11 11−1−15. AIRCRAFT IDENTIFICATION … 11−1−11 11−1−16. DESCRIPTION OF AIRCRAFT TYPES … 11−1−14 11−1−17. AIRCRAFT EQUIPMENT CODES … 11−1−14 11−1−18. AIRWAYS AND ROUTES … 11−1−15 11−1−19. NAVAID TERMS … 11−1−15 11−1−20. NAVAID FIXES … 11−1−16 11−1−21. RUNWAY CONDITIONS … 11−1−16

Table of Contents viii

11/3/22 JO 7110.10BB CHG 3

Chapter 12. Data Communication Systems

Section 1. General

Paragraph Page 12−1−1. TYPES OF DATA ACCEPTABLE ON FAA DATA COMMUNICATIONS SYSTEMS … 12−1−1 12−1−2. PRIORITY MESSAGES … 12−1−1 12−1−3. GROUP CODES … 12−1−1 12−1−4. MESSAGE FORMATS … 12−1−2 12−1−5. WMSCR NEGATIVE RESPONSE MESSAGES … 12−1−2 12−1−6. Q SIGNALS … 12−1−3

Appendices

Appendix A. FAA Form 7233−4 − International Flight Plan … Appendix A−1 Appendix B. FAA Form 7233−1 − Flight Plan … Appendix B−1 Appendix C. FAA Forms … Appendix C−1 Appendix D. Service B Message Formats … Appendix D−1 Appendix E. Domestic Flight Data (Legacy) … Appendix E−1 Appendix F. International Operations (Legacy) … Appendix F−1 Index … I−1 Pilot/Controller Glossary … PCG−1

Table of Contents ix

Chapter 1. General › Section 1. Introduction

Chapter 1. General

Section 1. Introduction

1−1−1. PURPOSE OF THIS ORDER

This order prescribes procedures and phraseology for use by air traffic personnel providing flight services. Flight service specialists are required to be familiar with the provisions of this order that pertain to their operational responsibilities and to exercise their best judgment if they encounter situations that are not covered.

1−1−2. AUDIENCE

This order applies to all ATO personnel and anyone using ATO directives.

1−1−3. WHERE TO FIND THIS ORDER

This order is available on the FAA Web site at http://faa.gov/air_traffic/publications & https://employees.faa.gov/tools_resources/orders_n otices/.

1−1−4. WHAT THIS ORDER CANCELS

FAA Order JO 7110.10AA, Flight Services, dated August 15, 2019, and all changes to it are canceled.

1−1−5. EXPLANATION OF CHANGES

The significant changes to this order are identified in the Explanation of Changes page(s). It is advisable to retain the page(s) throughout the duration of the basic order. If further information is desired, direct questions through the appropriate facility/service area office staff to Flight Services Safety and Operations Policy Group.

1−1−6. EFFECTIVE DATES AND SUBMISSIONS FOR CHANGES

a. This order and its changes are scheduled to be published to coincide with AIRAC dates, according to the table below.

b. The “Cutoff Date for Completion” in the table below refers to the deadline for a proposed change to

be fully coordinated and signed. Change initiators must submit their proposed changes well in advance of this cutoff date to meet the publication effective date. The process to review and coordinate changes often takes several months after the change is initially submitted.

TBL 1−1−1 Publication Schedule

Basic or

Change

Cutoff Date for

Completion

Effective Date of Publication

JO 7110.10BB 12/31/20 6/17/21

Change 1 6/17/21 12/2/21

Change 2 12/2/21 5/19/22

Change 3 5/19/22 11/3/22

JO 7110.10CC 11/3/22 4/20/23

Change 1 4/20/23 10/5/23

Change 2 10/5/23 3/21/24

Change 3 3/21/24 9/5/24

1−1−7. DELIVERY DATES

This order will be available on the FAA’s website 30 days prior to its effective date.

All organizations are responsible for viewing, downloading, and subscribing to receive electronic mail notifications when changes occur to this order. Subscriptions can be made at: https://www.faa.gov/air_traffic/publications/.

1−1−8. RECOMMENDATIONS FOR PROCEDURAL CHANGES

The responsibility associated with processing and coordinating revisions to this order is delegated to the Director, Policy, AJV-P.

a. Personnel should submit recommended changes in procedures to facility management.

b. Recommendations from other sources should be submitted through appropriate FAA, military, or industry/user channels.

Introduction 1−1−1

c. Proposed changes must be submitted electronically to 9−AJV−P−HQ−[email protected]. The submission should include a description of the recommended change and the proposed language to be used in the order.

NOTE− For details on the submission process as well as additional AJV−P processing responsibilities, please refer to FAA Order JO 7000.5, Procedures for Submitting Changes to Air Traffic Control Publications.

d. Procedural changes will not be made to this order until the operational system software has been adapted to accomplish the revised procedures.

1−1−9. SUBSCRIPTION INFORMATION

This publication may be purchased from the U.S.

Government Printing Office. Address subscription inquiries to:

Superintendent of Documents U.S. Government Publishing Office P.O. Box 979050 St. Louis, MO 63197−9000 Online: http://bookstore.gpo.gov

FAA air traffic publications are also available on the FAA’s web site at: http://www.faa.gov/air_traffic/publications/

1−1−10. DISTRIBUTION

This order is available online and will be distributed electronically to all offices that subscribe to receive email notification/access to it through the FAA’s website: https://www.faa.gov/air_traffic/publications/

1−1−2 Introduction

Chapter 1. General › Section 2. Terms of Reference

Section 2. Terms of Reference

1−2−1. WORD MEANINGS

As used in this order:

a. “Must” means a procedure is mandatory.

b. “Should” means a procedure is recommended.

c. “May” or “need not” means a procedure is optional.

d. “Will” means futurity, not a requirement for application of a procedure.

e. “Must not” means a procedure is prohibited.

f. Singular words include the plural.

g. Plural words include the singular.

h. “Aircraft” means the airframe, crew members, or both.

i. “Altitude” means indicated altitude mean sea level (MSL), flight level (FL), or both.

j. “Miles” means nautical miles unless otherwise specified and means statute miles in conjunction with visibility.

k. “Time,” when used for ATC operational activities, is the hour and the minute/s in Coordinated Universal Time (UTC). Change to the next minute is made at the minute plus 30 seconds, except time checks are given to the nearest quarter minute. The word “local” or the time zone equivalent must be stated when local time is given during radio and telephone communications. The term “ZULU” may be used to denote UTC.

l. “Sector,” when used in conjunction with flight service station (FSS) functions, means a specifically described geographic area that is assigned a National Airspace Data Interchange Network (NADIN) address.

m. “Tie−in facility,” as indicated in FAA Order JO 7350.9, Location Identifiers, for the purposes of this order, designates the responsible facility/sector for sending/receiving flight plans, flight notification messages, and performing search and rescue duties for the listed location.

n. “Shared database” is a database within an FSS operational system that is accessible by specialists in other geographical locations.

o. “Transmit” means to send data via NADIN or Weather Message Switching Center Replacement (WMSCR) to an outside recipient or to process data internally within an operational system that shares a global database.

p. “Form” means a paper record or an automated equivalent. Both must be retained in accordance with FAA directives.

q. “History files” means one or more digital or paper repositories of data that must be retained in accordance with FAA directives.

r. “Pertinent” means relating directly and significantly to the matter at hand.

1−2−2. NOTES

Statements of fact or of an explanatory nature and relating to the use of directive material have been identified and worded as “Notes.”

1−2−3. EXAMPLES

Any illustration used which serves to explain subject material is identified as an “Example.”

1−2−4. PHRASEOLOGY

Phraseology depicted in this order is mandatory.

NOTE− Exceptions to this paragraph are referenced in paragraph 4−1−1, Emergency Determination.

1−2−5. ABBREVIATIONS

Abbreviations authorized for use in the application of the procedures in this order are those contained in FAA Order JO 7340.2, Contractions.

1−2−6. JO 7110.10 CHANGES

a. Each reprinted, revised, or additional page will show the change number and the effective date of the change.

b. Bold lines in the margin of the text will mark the location of all changes except editorial corrections.

Terms of Reference 1−2−1

1−2−7. SYSTEM INSTRUCTIONS

Different operational systems are used to provide flight services within the United States. Each individual operational system must have instructions in the form of a user’s manual or guide, either

electronically or in paper form, that provide the necessary steps to accomplish the requirements set forth in this order.

Where databases are shared, local procedures may be used to facilitate the handling of flight data across the flight plan area boundaries.

1−2−2 Terms of Reference

Chapter 1. General › Section 3. Responsibility

JO 7110.10BB 6/17/21 12/2/21 JO 7110.10BB CHG 1

Section 3. Responsibility

1−3−1. PROCEDURAL APPLICATIONS

Apply the procedures in this order, except when other procedures are contained in a letter of agreement (LOA) or other appropriate FAA documents, provided they only supplement this order and any standards they specify are not less than those in this order.

NOTE− 1. Pilots are required to abide by applicable provisions of 14 Code of Federal Regulations (14 CFR) or any other pertinent regulations regardless of the application of any procedure in this order.

2. FAA Order JO 7210.3, Facility Operation and Administration, contains administrative instructions pertaining to these letters and documents.

1−3−2. DUTY PRIORITY

Because there are many variables involved, it is impossible to provide a standard list of duty priorities that apply to every situation. Each set of circumstances must be evaluated on its own merit, and when more than one action is required, personnel must exercise their best judgment based on the facts and circumstances known to them. Action which appears most critical from a safety standpoint should be performed first.

a. The following order of duty priorities is offered as a guideline.

1. Emergency Situations. Emergency situations are those where life or property is in immediate danger.

2. Inflight Services. Inflight services are those provided to or affecting aircraft in flight or otherwise operating on the airport surface. This includes services to airborne aircraft, airport advisories, delivery of air traffic control (ATC) clearances, advisories or requests, issuance of military flight advisory messages, notices to air missions (NOTAM), search and rescue (SAR) communications searches, flight plan handling, transcribed or live broadcasts, weather observations, pilot weather reports (PIREP), and pilot briefings.

3. Preflight Services. Preflight services are those which directly affect aircraft operations but

which are provided prior to actual departure and usually by telephone. These include pilot briefings, recorded data, flight plan filing/processing, and aircraft operational reservations.

1−3−3. DUTY FAMILIARIZATION AND TRANSFER OF POSITION RESPONSIBILITY

The transfer of position responsibility must be accomplished in accordance with appropriate facility directives each time the operational responsibility for a position is transferred from one specialist to another. The relieving specialist and the specialist being relieved must share equal responsibility for the completeness and accuracy of the position relief briefing.

a. Purpose. This paragraph prescribes the method and the step-by-step process for conducting a position relief briefing and transferring position responsibility from one specialist to another.

b. Discussion.

1. In all operational facilities, the increase in traffic density and the need for the expeditious movement of air traffic without compromising safety have emphasized the importance of the position relief process. Major problems occur whenever there is a heavy reliance upon memory unsupported by routines or systematic reminders. This procedure addresses the complete task of transferring position responsibility and the associated relief briefing.

2. Position relief unavoidably provides added workload for specialists at the time of relief. The intent of this procedure is to make the transfer of position responsibility take place smoothly and to ensure a complete transfer of information with a minimum amount of workload. The method takes advantage of a self-briefing concept in which the relieving specialist obtains needed status information by reading from the Status Information Areas to begin the relief process. Up-to-the-minute information relating to the provision of flight services to pilots and aircraft in flight requires verbal exchanges between specialists during the relief process. The method also specifies the point when the transfer of position responsibility occurs.

Responsibility 1−3−1

3. In the final part of the relief process, the specialist being relieved monitors and reviews the position to ensure that nothing has been overlooked or incorrectly displayed and that the transfer of position responsibility occurred with a complete briefing.

c. Terms. The following terms are important for a complete understanding of this procedure:

1. Status Information Areas. Manual or automated displays of the current status of position−related equipment and operational conditions or procedures.

2. Written Notes. Manually recorded items of information kept at designated locations on the positions of operation are elements of Status Information Areas.

3. Checklist. An ordered listing of items to be covered in a position relief briefing.

d. Precautions.

1. Specialists involved in the position relief process should not rush or be influenced to rush.

2. During position operation, each item of status information which is or may be an operational factor for the relieving specialist should be recorded as soon as it is operationally feasible so that it will not be forgotten or incorrectly recorded.

3. Extra care should be taken when more than one specialist relieves or is being relieved from a position at the same time; for example, combining or decombining positions.

e. Responsibilities. The specialist being relieved must be responsible for ensuring that any pertinent status information of which he/she is aware is relayed to the relieving specialist and is either:

1. Accurately displayed in the Status Information Areas for which he/she has responsibility, or

2. Relayed to the position having responsibility for accurately displaying the status information. Prior to accepting responsibility for a position, the relieving specialist must be responsible for ensuring that any unresolved questions pertaining to the operation of the position are resolved. The specialists engaged in a position relief must conduct the relief process at the position being relieved, unless other

procedures have been established and authorized by the facility air traffic manager.

f. Step−By−Step Process of Position Relief.

1. Preview of the Position

RELIEVING SPECIALIST

(a) Follow the checklist and review the Status Information Areas.

NOTE− This substep may be replaced by an authorized preduty briefing provided an equivalent review of checklist items is accomplished.

(b) Observe position equipment, operational situation, and the work environment.

(c) Listen to voice communications and observe other operational actions.

(d) Observe current and pending aircraft and vehicular traffic and correlate with flight and other movement information.

(e) Indicate to the specialist being relieved that the position has been previewed and that the verbal briefing may begin.

NOTE− Substeps (b), (c), and (d) may be conducted concurrently or in order.

2. Verbal Briefing

SPECIALIST BEING RELIEVED

(a) Review with the relieving specialist the checklist, Status Information Areas, written notes, and other prescribed sources of information, and advise of known omissions, updates, and inaccuracies. Also, brief the relieving specialist on the abnormal status of items not listed on the Status Information Areas, as well as on any items of special operational interest calling for verbal explanation or additional discussion.

(b) Brief on traffic, if applicable.

(c) Completely answer any questions asked.

(d) Observe overall position operation. If assistance is needed, provide or summon it as appropriate.

(e) Sign off the position in accordance with existing directives or otherwise indicate that the relief process is complete.

1−3−2 Responsibility

REFERENCE− FAA Order JO 7210.3, Para 2−2−4, Duty Familiarization and the Transfer of Position Responsibility. FAA Order JO 7210.3, Para 2−2−6, Sign In/Out and On/Off Procedures.

RELIEVING SPECIALIST

(f) Ask questions necessary to ensure a complete understanding of the operations situation.

(g) Make a statement or otherwise indicate to the specialist being relieved that position responsibility has been assumed.

(h) Sign on the position unless a facility directive authorizes substep (g) above.

(i) Check, verify, and update the information obtained in steps 1 and 2.

g. Check position equipment in accordance with existing directives.

Responsibility 1−3−3

Chapter 2. Pilot Briefing › Section 1. General

Chapter 2. Pilot Briefing

Section 1. General

2−1−1. DEFINITION

Pilot briefings are the translation of weather observations and forecasts, including surface, upper air, radar, satellite, and PIREPs into a form directly usable by the pilot or flight supervisory personnel to formulate plans and make decisions for the safe and efficient operation of aircraft. These briefings must also include information on NOTAM, flow control, and other items as requested.

2−1−2. PRE-DUTY REQUIREMENTS

Before assuming pilot briefing duties, familiarize yourself sufficiently with aeronautical and meteorological conditions to effectively provide briefing service. This includes:

a. General locations of weather-causing systems and general weather conditions.

b. Detailed information of current and forecast weather conditions for the geographical area(s) of responsibility.

c. Aeronautical information; for example, NOT­ AM, special use airspace (SUA), temporary flight restrictions (TFR), ATC delays, etc.

REFERENCE− Pertinent facility directives.

2−1−3. PREFLIGHT BRIEFING DISPLAY

Provide a preflight briefing display for specialist/pilot use. The contents and method of display must be based on individual facility requirements; for example, available equipment and space. Additional displays, as required, must be provided to ensure availability of information at all positions. At the discretion of facility management, provide a separate display for pilot use. All material in such displays must be current.

2−1−4. WEATHER DISPLAY PRODUCTS

a. The weather graphic display should include, but not necessarily be limited to, the following analysis, prognosis, and data products:

1. Weather Depiction.

2. Surface Analysis.

3. Forecast Winds Aloft.

4. Freezing Level Graphic.

5. G-AIRMET Graphic.

6. 12- and 24-hour Low Level Significant Weather Prognosis.

7. 12-, 24-, 36-, and 48-hour Surface Prognosis.

8. High Level Significant Weather Prognosis.

9. Current Icing Product (CIP).

10. Forecast Icing Product (FIP).

11. Graphical Turbulence Guidance (GTG).

12. National Weather Radar Summary. (CONUS Only).

13. National/Regional Radar Mosaics.

14. Radar Echo Tops.

15. Radar VAD Wind Profiles.

16. Visible/IR Satellite Imagery.

17. Constant Pressure Charts.

18. 500 MB Heights and Vorticity Analysis.

19. 500 MB Heights and Vorticity Prognosis.

20. 6−, 12−, 24−, 36−, and 48−hour 500 MB Heights and Vorticity Prognosis.

21. Convective Outlook.

22. Maximum Temperature 24− and 36−Hour Forecast (CONUS Only).

23. Minimum Temperature 24− and 36−Hour Forecast (CONUS Only).

b. Map features. (See FIG 2−1−1.)

c. Precipitation and obstruction to vision. (See FIG 2−1−2.)

General 2−1−1

FIG 2−1−1 Map Features Chart

FIG 2−1−2 NWS Surface Analysis Chart Common Weather

Symbols

REFERENCE− AC 00−45, Aviation Weather Services, Figure 4−7. NOTE− For a complete listing of weather map symbols, see “National Weather Service Observing Handbook,” Appendix C: https://www.weather.gov/media/owlie/ObservingHandbook1_2010_508_compliant.pdf.

d. Interpret and summarize weather radar displays as appropriate.

1. Use all available radar data and PIREPs to determine intensity, tops, area of coverage, movement, etc.

REFERENCE− P/CG Term − Precipitation Radar Weather Descriptions.

2. Identify data obtained from sources other than radar display by source and time of observation.

3. Define area of coverage in relation to VORs, airways for the route structure being flown, airports or geographic points to assist the pilot in relating coverage to route of flight or destination. EXAMPLE− ”A broken line of light to heavy echoes covers an area along and three zero miles east of a line from the Crazy Woman V−O−R to the Riverton V−O−R. Average tops between two-six thousand and three−four thousand. This line is increasing in intensity. Movement has been from northwest to southeast at three zero knots. The line includes an extreme echo one five miles in diameter on

2−1−2 General

Victor Two Ninety-eight forty−eight miles southeast of the Worland V−O−R, tops four three thousand. There are no known echoes within three-zero nautical miles of Victor Eight−five or Victor Two Ninety−eight south at this time.”

2−1−5. FORECASTS, WARNINGS, AND ADVISORIES

a. Use only weather forecasts, warnings, and advisories issued by a National Weather Service (NWS) office, including Center Weather Service Units (CWSUs), the U.S. military, foreign governments, or graphics systems owned/leased by the FAA or provided through a FAA−contracted service provider.

b. Use the OUTLOOK section of WSTs to provide information on where convective activity is expected. Use the Convective Outlooks (ACUS01 KWNS) to extract pertinent forecast information regarding the convective activity.

c. When an NWS forecast requires an amendment or correction, request assistance from the appropriate NWS office.

2−1−6. UNAVAILABILITY OF DATA

Use all available means to obtain the data required to brief pilots. If a complete briefing cannot be provided due to circuit problems or missing data, inform the pilot of this fact. Brief to the extent possible. Advise the pilot of the time you expect the data to be available.

2−1−7. TYPE OF BRIEFING TO BE CONDUCTED

Provide the pilot with the type of briefing requested (standard, abbreviated, or outlook). When it is not clear initially which type briefing is desired, provide the first one or two items requested, and then ascertain if the pilot would like a standard briefing. If a standard briefing is requested, conduct the briefing in accordance with paragraph 2−2−1. If the pilot does not desire a standard briefing, provide either an abbreviated briefing in accordance with paragraph 2−2−2 or an outlook briefing in accordance with paragraph 2−2−3.

2−1−8. LOGGING PILOT BRIEFINGS

a. Pilot briefings must be logged and retained in accordance with FAA Order 1350.14, Records Management. Briefings must be logged in operational systems when possible but may be logged manually if needed for operational efficiency.

b. Operational systems must, as a minimum, automatically record the facility/sector, date, position, time, and specialist identification for each logged briefing. In addition, enter the following information:

1. Departure and destination.

2. Aircraft identification. (The pilot’s name may be substituted for the aircraft identification, if unknown.)

3. Remarks, as applicable, to indicate OTLK (outlook briefing), AB (abbreviated briefing), and/or VNR.

c. (Alaska only) To manually log pilot briefings, use one of the following FAA forms:

1. FAA Form 7233−2, Pilot Briefing Log. Use a separate form each day. Two or more forms may be used simultaneously at different operating positions. Complete boxes 1 through 3 on each form. Enter appropriate data in columns 4, 5, 6, 7, 8 (if pertinent), and 9. If the pilot’s name is known, it may be substituted for the aircraft identification. As applicable, enter OTLK (outlook briefing), AB (abbreviated briefing), and/or VNR in column 8.

2. FAA Forms 7233−5, Inflight Contact Record, or 7230-21, Flight Progress Strip. Enter PB in block 14 if a briefing is provided. As applicable, also enter AB, OTLK, and/or VNR in the same block.

NOTE− See Appendix B for FAA forms.

d. Where audio recorders are used, facility management may limit entries on pilot briefing records to those required for facility use.

e. In Alaska, where fast−file recorders are used and the pilot states the source of a briefing on the recorder, it must be entered in the remarks field of the flight plan.

EXAMPLE− PB/ENA

General 2−1−3

Chapter 2. Pilot Briefing › Section 2. Preflight Pilot Briefing

JO 7110.10BB 6/17/21 12/2/21 JO 7110.10BB CHG 1

Section 2. Preflight Pilot Briefing

2−2−1. CONDUCT OF STANDARD BRIEFING

a. Brief by translating, interpreting, and summarizing available data for the intended flight. Do not read individual weather reports or forecasts unless, in your judgment, it is necessary to emphasize an important point or unless specifically requested to do so by the pilot. Obtain the following information if it is pertinent and not evident or already known:

1. Type of flight planned.

2. Aircraft identification or pilot’s name.

3. Aircraft type.

4. Departure point.

5. Route of flight.

6. Destination.

7. Flight altitude(s).

8. Estimated time of departure (ETD) and estimated time en route (ETE).

b. The specialist must issue the following cautionary advisory to a pilot planning a flight outside of United States controlled airspace, unless the pilot advises they have the international cautionary advisory.

PHRASEOLOGY− CHECK DATA AS SOON AS PRACTICAL AFTER ENTERING FOREIGN AIRSPACE, AS OUR INTERNATIONAL DATA MAY BE INACCURATE OR INCOMPLETE.

c. Using all sources of weather and aeronautical information, provide the following data when it is applicable to the proposed flight. Provide the information in subparagraphs c1 through c8 in the sequence listed except as noted.

1. Adverse Conditions. Include this element when meteorological or aeronautical conditions are reported or forecast that might influence the pilot to alter the proposed flight. Emphasize conditions that are particularly significant, such as low level wind shear, thunderstorms, reported icing, frontal zones along the route of flight, NOTAMs; for example, airport/runway closures, air traffic delays, TFRs etc. Weather advisories (WS, WA, WST, CWA, and

Aviation Watch Notification Messages (SAW)) must be given by stating the type of advisory followed by the pertinent information.

EXAMPLE− “An AIRMET is in effect until 1400Z for moderate turbulence below 10,000 feet over the mountainous area of southern California.” “Palmer airport closed” NOTE− NOTAMs in this category may be provided with NOTAMs listed in subparagraph c8.

2. VFR Flight Not Recommended (VNR). Include this statement when VFR flight is proposed and sky conditions or visibilities are present or forecast, surface or aloft, that in your judgment would make flight under visual flight rules doubtful. Describe the conditions, affected locations, and times.

PHRASEOLOGY− VFR FLIGHT NOT RECOMMENDED EXAMPLE− ‘‘There are broken clouds along the entire route between niner and one one thousand feet. With the approach of a cold front, these clouds are forecast to become overcast and to lower to below seven thousand with mountains and passes becoming obscured. V-F-R flight not recommended between Salt Lake City and Grand Junction after two two zero zero ZULU.” ‘‘V-F-R flight not recommended in the Seattle area until early afternoon. The current weather at Seattle is indefinite ceiling three hundred, visibility one, mist, and little improvement is expected before one eight zero zero ZULU.” NOTE− This recommendation is advisory in nature. The decision as to whether the flight can be conducted safely rests solely with the pilot.

3. Synopsis. Provide a brief statement describing the type, location, and movement of weather systems and/or air masses which might affect the proposed flight. This element may be combined with adverse conditions and/or the VNR element, in any order, when it will help to more clearly describe conditions.

4. Current Conditions. Summarize from all available sources reported weather conditions applicable to the flight. This element may be omitted if the proposed time of departure is beyond 2 hours,

Preflight Pilot Briefing 2−2−1

JO 7110.10BB 6/17/21 3/15/07 7110.65R CHG 2 JO 7110.10BB CHG 1 12/2/21

unless the information is requested by the pilot. If AUTO appears after the date/time element and is presented as a singular report, follow the location with the word “AUTOMATED.”

5. En Route Forecast. Summarize forecast information that will affect the proposed flight; for example, area forecasts for the Gulf of Mexico, Caribbean, Alaska, and Hawaii; Static Graphical Forecast Images for the CONUS, TAFs, prognosis charts, weather advisories, etc. Provide the information in a logical order; for example, climb out, en route, and descent.

6. Destination Forecast. Provide the destination forecast including significant changes expected within 1 hour before and after the estimated time of arrival (ETA).

7. Winds Aloft. Provide forecast winds aloft for the flight using degrees of the compass. Interpolate wind directions and speeds between levels and stations as necessary. Provide temperature information on request.

8. Notices to Air Missions (NOTAM). Provide NOTAM information affecting the flight:

(a) NOTAM (D). All NOTAMs (D), including SUA NOTAMs for restricted areas, aerial refueling, and night vision goggles (NVG).

NOTE− Other SUA NOTAMs (D) such as military operations area (MOA), military training route (MTR) and warning area NOTAMs, are considered “upon request” briefing items as indicated in paragraph 2−2−1c12(a).

(b) Combine this element with adverse conditions when it would be logical and advantageous to do so.

9. Prohibited Areas P-40, P-56, and the Special Flight Rules Area (SFRA) for Washington, DC. Include this element when pertinent to the route of flight. Advise the pilot that VFR flight within 60 miles of the DCA VOR/DME requires Special Awareness Training.

NOTE− Refer to 14 CFR Part 93 for additional information such as special awareness for flights in and around SFRAs and/or areas that require special air traffic rules.

10. ATC Delays. Inform the pilot of ATC delays and/or flow control advisories that might affect the proposed flight.

11. Request for PIREPs. Include this element when in your judgment, a report of actual inflight conditions is beneficial or when conditions meet criteria for solicitation of PIREPs (paragraph 8−2−4). Advise the pilot to contact Flight Service to report en route conditions.

12. Upon Request. Provide any information requested by the pilot, including, but not limited to:

(a) Special use airspace, except those listed in paragraph 2−2−1c8(a), SUA-related airspace (air traffic control assigned airspace (ATCAA)), and MTR activity. For all SUA and MTR data requests, advise the pilot that information may be updated periodically and to contact the appropriate ATC facility for additional information while in flight.

NOTE− For the purpose of this paragraph, SUA and related airspace includes the following types of airspace: alert area, MOA, warning area and ATCAA. MTR data includes the following types of airspace: instrument flight rule (IFR) training routes (IR), VFR training routes (VR), and slow training routes (SR).

(b) Approximate density altitude data.

(c) Information regarding such items as air traffic service and rules, customs/immigration procedures, air defense identification zone (ADIZ) rules, SAR, etc.

(d) Military NOTAMs.

REFERENCE− FAA Order 7930.2, Paragraph 8−3−1, Military NOTAM Availability.

(e) Special FDC instrument approach procedure changes.

(f) FDC NOTAMs containing amendments to airways, airport, and facility IFR procedures and General Information.

NOTE− General FDC NOTAMs include Chart amendments, Special Security Instructions, and Special Advisory Notices.

(g) Information contained in the Federal NOTAM System (FNS) NOTAM Search external links or Air Traffic Plans and Publications website, to include Domestic Notices and International Notices.

2−2−2 Preflight Pilot Briefing

JO 7110.10BB 6/17/21 12/2/21 JO 7110.10BB CHG 1

2−2−2. CONDUCT OF ABBREVIATED BRIEFING

a. Provide an abbreviated briefing when a pilot requests information to supplement mass-disseminated data; update a previous briefing; or when the pilot requests that the briefing be limited to specific information. If applicable, include the statement “VFR flight not recommended” in accordance with subparagraph 2−2−1c2. The specialist must issue the following cautionary advisory to a pilot planning a flight outside of United States controlled airspace, unless the pilot advises they have the international cautionary advisory.

PHRASEOLOGY− CHECK DATA AS SOON AS PRACTICAL AFTER ENTERING FOREIGN AIRSPACE, AS OUR INTERNATIONAL DATA MAY BE INACCURATE OR INCOMPLETE.

b. Conduct abbreviated briefings as follows:

1. When a pilot desires specific information only, provide the requested information. If adverse conditions are reported or forecast, advise the pilot. Provide details on these conditions, in accordance with subparagraph 2−2−1c1, at the pilot’s request.

2. When a pilot requests an update to a previous briefing, obtain from the pilot the time the briefing was received and necessary background information. To the extent possible, limit the briefing to

appreciable changes in meteorological and aeronautical conditions since the previous briefing.

3. When a pilot requests information to supplement data obtained through FSS mass-dissemination media, obtain pertinent background information, the specific items required by the pilot, and provide the information in the sequence listed in subparagraph 2−2−1c.

4. When a pilot requests to file a flight plan only, ask if he/she requires the latest information on adverse conditions along the route of flight. If so, provide the information pertinent to the route of flight in accordance with subparagraph 2−2−1c1.

5. Solicit PIREPs in accordance with subparagraph 2−2−1c11.

2−2−3. CONDUCT OF OUTLOOK BRIEFING

a. Provide an outlook briefing when the proposed departure is 6 hours or more from the time of the briefing. Conduct the briefing in accordance with subparagraph 2−2−1c. Omit items in subparagraphs c2, c4, and c7 through c11, unless specifically requested by the pilot or deemed pertinent by the specialist.

b. When the proposed flight is scheduled to be conducted beyond the valid time of the available forecast material, provide a general outlook and then advise the pilot when complete forecast data will be available for the proposed flight.

Preflight Pilot Briefing 2−2−3

Chapter 3. Inflight Services › Section 1. General

Chapter 3. Inflight Services

Section 1. General

3−1−1. INFLIGHT SERVICES

a. Inflight services are those provided to or affecting aircraft inflight or otherwise operating on the airport surface. This includes services to airborne aircraft, such as delivery of ATC clearances, advisories or requests, issuance of military flight advisory messages, NOTAM, SAR communications searches, flight plan handling, transcribed or live broadcast, weather observations, PIREPs, and pilot briefings.

b. Upon request, provide en route aircraft with timely and pertinent weather data tailored to a specific altitude and route using the most current available sources of aviation meteorological information. Tailor en route flight advisories to the phase of flight that begins after climb out and ends with descent to land. Current weather and terminal forecast at the airport of first intended landing and/or the alternate airport must be provided on request. When conditions dictate, provide information on weather for alternate routes and/or altitudes to assist the pilot in the avoidance of hazardous flight conditions.

NOTE− Provide inflight services in accordance with the procedures in this chapter to aircraft on a “first come, first served” basis, as circumstances permit.

c. Prior to assuming inflight duties, the specialist must review, as a minimum, the graphic information listed in subparagraph 2−1−4a, Weather Display Products (if available). After assuming duties, the specialist must continue to review graphic and written data as needed during the watch to update and maintain a thorough knowledge of weather synoptic and forecast information affecting aviation operations.

3−1−2. OPERATIONAL PRIORITY

a. Emergency situations are those where life or property are in immediate danger. Aircraft in distress have priority over all other aircraft.

b. Treat air ambulance flights as follows:

1. Provide priority handling to civil air ambulance flights when the pilot, in radio transmissions, verbally identifies the flight by stating “MEDEVAC” followed by the FAA authorized call sign or the full civil registration letters/numbers. Good judgment must be used in each situation to facilitate the most expeditious movement of a MEDEVAC aircraft.

NOTE− If a flight plan includes the letter “L” for “MEDEVAC” and/or includes “MEDEVAC” in Item 11 (Remarks) of the flight plan or Item 18 (Other Information) of an international flight plan, the entries are considered informational in nature only and not an identification for operational priority.

REFERENCE− FAA Order JO 7110.10, Para 11−1−15, Aircraft Identification.

2. Provide priority handling to AIR EVAC and HOSP flights when verbally requested by the pilot.

NOTE− If a flight plan includes “HOSP” or “AIR EVAC” in either Item 11 (Remarks) of the flight plan or Item 18 (Other Information) of an international flight plan, the entries are considered informational in nature only and not an identification for operational priority.

3. Assist the pilots of MEDEVAC, AIR EVAC, and HOSP aircraft to avoid areas of significant weather and adverse conditions.

4. If requested by a pilot, provide additional assistance (i.e., landline notifications) to expedite ground handling of patients, vital organs, or urgently needed medical materials.

c. Provide maximum assistance to search and rescue (SAR) aircraft performing a SAR mission.

d. Provide special handling as required to expedite Flight Check and automated flight inspection “Flight Check (number) Recorded” aircraft.

3−1−3. INFLIGHT WEATHER BRIEFING

Upon request, provide inflight weather briefings, in accordance with the procedure outlined in Chapter 2, Section 2.

General 3−1−1

3−1−4. INFLIGHT EQUIPMENT MALFUNCTIONS

a. Inflight equipment malfunctions include partial or complete failure of equipment which may affect either safety and/or the ability of the flight to proceed.

b. When a pilot reports a flight equipment malfunction, determine the nature and extent of any assistance desired.

c. Provide maximum assistance possible consistent with equipment and any special handling requested.

d. Relay to other specialists or facilities who will handle the aircraft all information concerning the equipment malfunction on the aircraft and any special handling requested or being provided.

3−1−5. AIRCRAFT REPORTED MALFUNCTIONS

a. Aircraft-reported NAVAID malfunctions are subject to varying circumstances. When an aircraft reports a ground-based NAVAID malfunction, take the following action:

1. Request a report from a second aircraft.

2. If the second aircraft reports normal operations, if able, inform the first aircraft. Record the incident on FAA Form 7230-4, Daily Record of Facility Operation.

3. If the second aircraft confirms the malfunction:

(a) Notify the appropriate IFR control facility or sector.

(b) Notify Technical Operations personnel.

(c) Take NOTAM action when requested by Technical Operations personnel.

(d) Record the incident on FAA Form 7230-4.

4. In the absence of a second aircraft report:

(a) Notify Technical Operations and advise what time the initial aircraft reported the failure and when a second aircraft report might be obtained.

(b) Record the incident on FAA Form 7230-4.

b. When an aircraft reports a global positioning system (GPS)/global navigation satellite system (GNSS) anomaly:

1. Request the following information:

(a) Aircraft call sign and type of aircraft.

(b) Date and time of the occurrence.

(c) Location of anomaly.

(d) Altitude.

2. Record the incident on FAA Form 7230-4.

3. Forward this information to the traffic management unit (TMU) and Technical Operations personnel.

c. When an aircraft reports a Wide Area Augmentation System (WAAS) anomaly, request the following information and/or take the following actions:

1. Determine if the pilot has lost all WAAS service.

EXAMPLE− “Are you receiving any WAAS service?”

2. If the pilot reports receipt of any WAAS service, acknowledge the report, and continue normal operations.

3. If the pilot reports loss of all WAAS service, report as a GPS anomaly using procedures in paragraph 3−1−5b.

d. When a pilot reports an ADS-B services malfunction (i.e., ADS-B, TIS-B, FIS-B, or ADS-R):

1. Request the following information:

(a) Aircraft call sign and type of aircraft.

(b) Date and time of observation.

(c) Location and altitude of anomaly.

(d) Condition observed (or anomaly).

(e) Type and software version of avionics system.

2. Forward this information to an Operations Control Center (OCC) or Service Operations Center (SOC) as appropriate.

3. Record the incident on FAA Form 7230-4.

3−1−2 General

3−1−6. NAVAID FLIGHT CHECK

Provide maximum assistance to aircraft engaged in flight inspection of NAVAIDs. Unless otherwise agreed to, maintain direct contact with the pilot and provide information regarding known traffic in the area and request the pilot’s intentions.

NOTE− 1. Many flight inspections are accomplished using

automatic recording equipment. An uninterrupted flight is necessary for successful completion of the mission. The workload for the limited number of aircraft engaged in these activities requires strict adherence to a schedule.

2. Flight inspection operations which require special participation of ground personnel, specific communications, or radar operation capabilities are considered to require special handling. These flights are coordinated with appropriate facilities before departure.

General 3−1−3

Chapter 3. Inflight Services › Section 2. Data Recording

Section 2. Data Recording

3−2−1. TYPES OF DATA RECORDED

a. Operational system entries for:

1. Flight plans and related messages.

2. Logging pilot briefings and aircraft contacts.

3. Weather/Flight data messages.

b. Manual strip marking.

3−2−2. METHODS OF RECORDING DATA

a. Except as provided in 3−2−2b, all entries must be made directly into the operational system.

b. Locally-approved procedures may be used to manually record data during heavy traffic periods or system outages. Aircraft contact information should be logged in the operational system as soon as practical.

c. Use control/clearance symbols, abbreviations, location identifiers, and contractions for recording position reports, traffic clearances, and other data. When recording data either electronically or manually, you may use:

1. Plain language to supplement data when it will aid in understanding the recorded information.

2. Locally-approved contractions and identifiers for frequently used terms and local fixes not listed in either FAA Order JO 7340.2, Contractions, or FAA Order JO 7350.9, Location Identifiers. Use only within your facility, not on data or interphone circuits. All locally-approved contractions and identifiers must be placed in facility files for record and reference purposes.

d. When recording data manually, use the standard hand-printed characters shown in FIG 3−2−1 to prevent misinterpretation.

FIG 3−2−1 Hand-Printed Characters Chart

Data Recording 3−2−1

NOTE− A slant line crossing through the numeral zero and an underline of the letter “S” on handwritten portions of flight progress strips are required only when there is reason to believe the lack of these markings could lead to a misunderstanding. A slant line through the numeral zero is required on all weather data.

1. To correct or update data, draw a horizontal line through it and write the correct information adjacent to it.

2. Do not erase any item.

3−2−3. IFR/VFR/DVFR FLIGHT PLAN RECORDING

a. Use the operational system to record and file flight plans, flight plan modifications, cancellations, activations, and closures for appropriate distribution and processing. Detailed instructions are contained in the operational system manuals.

NOTE− FSS operational systems contain an electronic equivalent of authorized FAA Flight Plan Forms.

b. When closing an active VFR flight plan, obtain departure point and destination, if not already known.

NOTE− A canceled VFR flight plan is one that is removed from a proposed list and has not been activated. A closed VFR flight plan is one that has been activated and is then removed from an inbound list.

c. Flight plan information may initially be recorded on FAA Form 7233-1 or other paper prior to entry into the operational system.

3−2−4. FLIGHT PROGRESS STRIPS (FAA FORMS 7230-21 AND 7233-5)

a. When officially used to record inflight data, use flight progress strips to record:

1. Aircraft contacts.

2. ATC clearances.

3. Pilot briefings on airborne aircraft.

4. Other operationally significant items.

b. Use a flight progress strip for each aircraft and record all contacts with that aircraft on the same strip. If supplemental strips are needed for additional writing space, keep the original and supplemental strips together.

NOTE− Multiple flights by the same aircraft may be recorded on a single strip when situational awareness and strip bay efficiency are improved.

3−2−5. FLIGHT PROGRESS STRIPS AND ENTRY DATA

a. Flight progress strip. (See FIG 3−2−2.)

b. Flight progress strip entry. (See FIG 3−2−3 and FIG 3−2−4.)

FIG 3−2−2 Flight Progress Strip

3−2−2 Data Recording

FIG 3−2−3 Strip Entry 1

FIG 3−2−4 Strip Entry 2

Data Recording 3−2−3

c. Flight progress strip Item and Information. d. Flight progress strip abbreviation. (See TBL 3−2−1.) (See TBL 3−2−2 )

TBL 3−2−2 TBL 3−2−1 Item and Information Abbreviation

Item Information

1

Aircraft Identification (ACID) (To identify IFR aircraft piloted by solo USAF under-graduate pilot, the letter Z will be added to aircraft ID on the flight progress strip. Do not use the suffix in ground-to-air communications.) 2 Type of aircraft/special equipment. 3 True airspeed (TAS) and altitude (IFR). Altitude (VFR/DVFR, if known). 4 Departure point. 5 Route of flight. 6 Destination. 7 Actual departure time, or time VFR flight plan activated. 8 ETA at destination. 9 Estimated time of fuel exhaustion. 10 Type of flight. 11 Action time; for example, overdue time, fuel exhaustion time, LR contact time. 12 Time of contact with pilot. 13 Information received from pilot/another facility. 14 Data issued to the aircraft.

Abbreviation Meaning Õ Over Flight ↓ Inbound Flight ↑ Outbound Flight A AIRMET (WA) AA Airport Advisory CWT Caution Wake Turbulence D DVFR DA Decided Against Flight DD Decided to Delay Flight DW Downwind FP Filed Flight Plan I IFR IC Incomplete Briefing PB Pilot Brief RY Runway S SVFR V VFR VNR VFR Flight not recommended (Pilot Brief) WS SIGMET WST Convective SIGMET e. Record ATC instructions and clearances completely and exactly.

f. Summarize other data using approved symbols and contractions. (See FIG 3−2−5 and FIG 3−2−6.)

3−2−4 Data Recording

FIG 3−2−5 Control Information Symbols Chart 1

Data Recording 3−2−5

FIG 3−2−6 Control Information Symbols Chart 2

g. Do not record issuance of altimeter setting unless that is the only information provided during the contact.

3−2−6. AIRCRAFT CONTACTS

a. Inflight contacts may be logged in the operational system, on flight progress strips, or on facility approved alternate forms.

b. When using flight progress strips, if the station has the aircraft’s flight plan, enter “FP” in item 14 on the strip to show the flight plan is on file at the facility.

c. If there is no flight plan on file for the aircraft, the following must be obtained:

1. ACID.

2. Type of flight.

3. Time of contact.

3−2−6 Data Recording

4. Other items which are operationally significant.

d. If the inflight position is recorded, you may limit entries in the aircraft contact portion of the strip to those necessary for your use.

e. Log aircraft contacts using the operational system. The following should be logged using the symbols in TBL 3−2−3 and TBL 3−2−4:

1. Type of Briefing

(a) Standard

(b) Abbreviated

(c) Outlook

2. Type of Flight

(a) IFR

(b) VFR

(c) Defense VFR (DVFR)

3. Category of Flight TBL 3−2−4 Miscellaneous Abbreviation (a) Air Carrier

D Cleared to depart from the fix. F Cleared to the fix.

H Cleared to hold and instructions issued. L Cleared to land. N Clearance not delivered. O Cleared to the outer marker.

PD Cleared to climb/descend at pilot’s discretion.

Q

Cleared to fly specified sectors of a NAVAID defined in terms of courses, bearings, radials, or quadrants within a designated radius.

T

Cleared through (for landing and takeoff through intermediate point). V Cleared over the fix.

X Cleared to cross (airway, route, radial) at (point). Z Tower jurisdiction.

(b) Air Taxi

(c) Military

(d) General Aviation

4. Aircraft ID

5. Type of Service

(a) Airport advisory

(b) Clearance(s); for example, IFR, special VFR (SVFR)

6. Remarks. Operating Position (if not automatically logged by operational system)

TBL 3−2−3 Clearance Abbreviation

Abbreviation Meaning

A Cleared to airport (point of intended landing). B Center clearance delivered

C

ATC clears (when clearance relayed through non-ATC facility). CAF Cleared as filed.

Abbreviation Meaning BC Back course approach. CT Contact approach. FA Final approach. GPS GPS approach. I Initial approach. ILS ILS approach. MA Missed approach. MLS MLS approach. NDB Nondirectional radio beacon approach. OTP VFR conditions-on-top. PA Precision approach. PT Procedure turn. RH Runway heading. RP Report immediately upon passing (fix/altitude). RX Report crossing. SA Surveillance approach. SI Straight-in approach. TA TACAN approach. TL Turn left. TR Turn right. VA Visual approach. VR VOR approach.

Data Recording 3−2−7

Chapter 3. Inflight Services › Section 3. Radio Communications

Section 3. Radio Communications

3−3−1. FREQUENCY USE

a. Use radio frequencies for the specific purposes for which they are intended. A frequency may be used for more than one function when required. Use the minimum number of frequencies to conduct communications. Request pilots file flight plans on discrete frequencies when possible.

b. Monitor assigned radio frequencies continuously. Keep speaker volumes at a level sufficient to hear all transmissions.

3−3−2. AUTHORIZED TRANSMISSIONS

a. Transmit only those messages necessary for safe and efficient use of the National Airspace System (NAS).

1. Relay operational information to an aircraft or its company, as requested, when abnormal conditions necessitate such requests. Do not agree to handle such messages on a regular basis.

2. Relay official FAA messages as required.

b. Inform an aircraft of the source of any message you relay from an appropriate authority.

c. Use the words or phrases in radio communications as contained in the P/CG.

3−3−3. RADIO MESSAGE FORMAT

a. Use the following format for radio communications with an aircraft:

1. Identification of aircraft.

2. Identification of the calling unit.

3. The type of message to follow when this will assist the pilot.

4. The word “over,” if required.

b. Specialist initiated call. State the prefix , for example “November” when establishing initial communications with U.S.−registered aircraft followed by the International Civil Aviation Organization (ICAO) phonetic pronunciation of the numbers/letters of the aircraft registration. The specialist may state the aircraft type, the model, the manufacturer’s name, followed by the ICAO

phonetic pronunciation of the numbers/letters of the aircraft registration if used by the pilot on the initial or subsequent call.

EXAMPLE− Specialist initiated call:

“November One Two Three Four Golf, Juneau Radio, over.” “Piper Three Four Seven Seven Papa, Fort Worth Radio, A-T-C clearance, over.”

c. Replying to call up from aircraft. Identification of the aircraft initiating the call up. Use the full identification in reply to aircraft with similar sounding identifications. For other aircraft, use the same identification the pilot used in initial call up; then use the correct identification after communication has been established. The specialist may state the aircraft type, model, or manufacturer’s name followed by the ICAO phonetic pronunciation of the numbers/letters of the aircraft registration if used by the pilot.

EXAMPLE− Responding to pilot’s initial or subsequent call:

“Jet Commander One Two Three Four Papa.”

“Bonanza One Two Three Four Tango.”

“November Six Three Eight Mike Foxtrot.”

d. The word “heavy” must be used as part of the identification in communications with or about heavy jet aircraft.

PHRASEOLOGY− UNITED FIFTY-EIGHT HEAVY.

NOTE− 1. Most airlines use the word “heavy” following the company prefix and trip number when establishing communications or when changing frequencies.

2. When in radio-telephone communications with “Air Force One,” do not add the “heavy” designator to the call sign. State only the call sign “Air Force One” regardless of the type of aircraft.

e. Preface a clearance or instruction intended for a specific aircraft with the identification of that aircraft.

f. Emphasize appropriate digits, letters, or similar sounding words to aid in distinguishing between similar sounding aircraft identifications.

Radio Communications 3−3−1

JO 7110.10BB 6/17/21 3/15/07 7110.65R CHG 2 JO 7110.10BB CHG 1 12/2/21

Additionally, notify each pilot concerned when communicating with aircraft having similar sounding identifications.

EXAMPLE− “American Five Twenty-one and American Twenty-one, transmissions being made to each of you on this frequency.”

“Advisory to Cessna One Three Two Four, transmissions to Cessna One Two Three Four also being made on this frequency.”

3−3−4. ABBREVIATED TRANSMISSION

Transmissions may be abbreviated as follows:

a. Use the identification prefix and the last three digits or letters of the aircraft identification after communications have been established. Do not abbreviate similar sounding aircraft identifications or the identification of an air carrier or other civil aircraft having an FAA-authorized call sign.

b. Omit the facility identification after communication has been established.

c. Transmit the message immediately after the call up (without waiting for the aircraft’s reply) when the message is short and receipt is generally assured.

d. Omit the word “over” if the message obviously requires a reply.

3−3−5. ROUTINE RADIO CONTACTS

Record information received from or given to the pilot. Prior to terminating the contact, provide the following information if it is pertinent and the pilot indicates that it has not been received previously.

a. Weather Advisory. When a weather advisory such as a WA, WS, WST, CWA, or SAW which affects an aircraft’s position, route, or destination.

b. NOTAM. Inform the pilot of any pertinent NOTAMs affecting the flight.

c. Altimeter Setting.

1. If the aircraft is operating below 18,000 feet MSL, issue current altimeter setting obtained from direct reading instruments or received from weather reporting stations. Use the setting for the location nearest the position of the aircraft.

2. If the aircraft is arriving or departing a local airport served by an operating control tower, issue altimeter setting on request only.

3. When a pilot acknowledges that he/she has received the AFIS broadcast, specialists may omit those items contained in the broadcasts if they are current (Alaska only).

4. Aircraft arriving or departing from a non-towered airport which has a commissioned automated weather reporting with ground-to-air capability must be advised to monitor the automated weather frequency for the altimeter setting.

PHRASEOLOGY− MONITOR (location) AUTOMATED WEATHER FOR CURRENT ALTIMETER.

NOTE− This requirement is deleted if the pilot states that he/she has the automated weather.

5. When the barometric pressure is greater than 31.00 inches Hg., Flight Standards will implement high barometric pressure procedures by NOTAM, defining the geographic area affected. When this occurs, use the following procedures:

(a) IFR aircraft. Issue the altimeter setting and advise the pilot that high pressure altimeter setting procedures are in effect. Control facilities will issue specific instructions when relaying IFR clearances and control instructions through FSS facilities when the altimeter is above 31.00 inches Hg.

(b) VFR aircraft. Issue the altimeter setting. Advise the pilot that high pressure altimeter setting procedures are in effect and to use an altimeter setting of 31.00 inches Hg en route.

PHRASEOLOGY− ALTIMETER IN EXCESS OF THREE ONE ZERO ZERO. HIGH PRESSURE ALTIMETER SETTING PROCEDURES ARE IN EFFECT. RECOMMEND YOU SET ALTIMETER THREE ONE ZERO ZERO EN ROUTE.

NOTE− Airports unable to accurately measure barometric pressures above 31.00 inches Hg will report the barometric pressure as missing or in excess of 31.00 inches Hg. Flight operations to or from those airports are restricted to VFR weather conditions.

REFERENCE− AIM, Chapter 7, Section 2, Altimeter Setting Procedures. FAA Order JO 7110.65, Para 2−7−2 g, Altimeter Setting Issuance Below Lowest Usable FL.

3−3−2 Radio Communications

d. Incorrect Cruising Altitude. If the aircraft is operating VFR at an altitude between 3,000 feet AGL to, but not including FL180, and reports at an incorrect cruising altitude for the direction of flight, issue a VFR cruising altitude advisory.

PHRASEOLOGY− V-F-R CRUISING LEVELS FOR YOUR DIRECTION OF FLIGHT ARE: (Odd/Even) ALTITUDES PLUS FIVE HUNDRED FEET.

NOTE− Facilities located in those areas where VFR altitude separation is below 3,000 feet AGL or above FL 180 must provide appropriate phraseology examples for local use.

e. Altimeter Setting in Millibars (MBs). If a request for the altimeter setting in MBs is received, use the setting for the location nearest the position of the aircraft and convert to the MBs equivalent value using a MBs conversion chart. If the Mbs setting is not a whole number, always round down. (See TBL 3−3−1.)

TBL 3−3−1 Millibar Conversion Chart

MILLIBAR CONVERSION CHART inches millibars inches millibars inches millibars inches millibars inches millibars inches millibars inches millibars inches millibars 27.50 931.3 28.00 948.2 28.50 965.1 29.00 982.1 29.50 999.0 30.00 1015.9 30.50 1032.8 31.00 1049.8 27.51 931.6 28.01 948.5 28.51 965.5 29.01 982.4 29.51 999.3 30.01 1016.3 30.51 1033.2 31.01 1050.1 27.52 931.9 28.02 948.9 28.52 965.8 29.02 982.7 29.52 999.7 30.02 1016.6 30.52 1033.5 31.02 1050.5 27.53 932.3 28.03 949.2 28.53 966.1 29.03 983.1 29.53 1000.0 30.03 1016.9 30.53 1033.9 31.03 1050.8 27.54 932.6 28.04 949.5 28.54 966.5 29.04 983.4 29.54 1000.3 30.04 1017.3 30.54 1034.2 31.04 1051.1 27.55 933.0 28.05 949.9 28.55 966.8 29.05 983.7 29.55 1000.7 30.05 1017.6 30.55 1034.5 31.05 1051.5 27.56 933.3 28.06 950.2 28.56 967.2 29.06 984.1 29.56 1001.0 30.06 1017.9 30.56 1034.9 31.06 1051.8 27.57 933.6 28.07 950.6 28.57 967.5 29.07 984.4 29.57 1001.4 30.07 1018.3 30.57 1035.2 31.07 1052.2 27.58 934.0 28.08 950.9 28.58 967.8 29.08 984.8 29.58 1001.7 30.08 1018.6 30.58 1035.6 31.08 1052.5 27.59 934.3 28.09 951.2 28.59 968.2

29.09 985.1 29.59 1002.0 30.09 1019.0 30.59 1035.9 31.09 1052.8 27.60 934.6 28.10 951.6 28.60 968.5 29.10 985.4 29.60 1002.4 30.10 1019.3 30.60 1036.2 31.10 1053.2 27.61 935.0 28.11 951.9 28.61 968.8 29.11 985.8 29.61 1002.7 30.11 1019.6 30.61 1036.6 31.11 1053.5 27.62 935.3 28.12 952.3 28.62 969.2 29.12 986.1 29.62 1003.0 30.12 1020.0 30.62 1036.9 31.12 1053.8 27.63 935.7 28.13 952.6 28.63 969.5 29.13 986.5 29.63 1003.4 30.13 1020.3 30.63 1037.3 31.13 1054.2 27.64 936.0 28.14 952.9 28.64 969.9 29.14 986.8 29.64 1003.7 30.14 1020.7 30.64 1037.6 31.14 1054.5 27.65 936.3 28.15 953.3 28.65 970.2 29.15 987.1 29.65 1004.1 30.15 1021.0 30.65 1037.9 31.15 1054.9 27.66 936.7 28.16 953.6 28.66 970.5 29.16 987.5 29.66 1004.4 30.16 1021.3 30.66 1038.3 31.16 1055.2 27.67 937.0 28.17 953.9 28.67 970.9 29.17 987.8 29.67 1004.7 30.17 1021.7 30.67 1038.6 31.17 1055.5 27.68 937.4 28.18 954.3 28.68 971.2 29.18 988.1 29.68 1005.1 30.18 1022.0 30.68 1038.9 31.18 1055.9 27.69 937.7 28.19 954.6 28.69 971.6 29.19 988.5 29.69 1005.4 30.19 1022.4 30.69 1039.3 31.19 1056.2 27.70 938.0 28.20 955.0 28.70 971.9

29.20 988.8 29.70 1005.8 30.20 1022.7 30.70 1039.6 31.20 1056.6 27.71 938.4 28.21 955.3 28.71 972.2 29.21 989.2 29.71 1006.1 30.21 1023.0 30.71 1040.0 31.21 1056.9 27.72 938.7 28.22 955.6 28.72 972.6 29.22 989.5 29.72 1006.4 30.22 1023.4 30.72 1040.3 31.22 1057.2 27.73 939.0 28.23 956.0 28.73 972.9 29.23 989.8 29.73 1006.8 30.23 1023.7 30.73 1040.6 31.23 1057.6 27.74 939.4 28.24 956.3 28.74 973.2 29.24 990.2 29.74 1007.1 30.24 1024.0 30.74 1041.0 31.24 1057.9 27.75 939.7 28.25 956.7 28.75 973.6 29.25 990.5 29.75 1007.5 30.25 1024.4 30.75 1041.3 31.25 1058.2 27.76 940.1 28.26 957.0 28.76 973.9 29.26 990.8 29.76 1007.8 30.26 1024.7 30.76 1041.6 31.26 1058.6 27.77 940.4 28.27 957.3 28.77 974.3 29.27 991.2 29.77 1008.1 30.27 1025.1 30.77 1042.0 31.27 1058.9 27.78 940.7 28.28 957.7 28.78 974.6 29.28 991.5 29.78 1008.5 30.28 1025.4 30.78 1042.3 31.28 1059.3 27.79 941.1 28.29 958.0 28.79 974.9 29.29 991.9 29.79 1008.8 30.29 1025.7 30.79 1042.7 31.29 1059.6 27.80 941.4 28.30 958.3 28.80 975.3 29.30 992.2 29.80 1009.1 30.30 1026.1 30.80 1043.0 31.30 1059.9 27.81 941.8 28.31 958.7 28.81 975.6

29.31 992.6 29.81 1009.5 30.31 1026.4 30.81 1043.3 31.31 1060.3 27.82 942.1 28.32 959.0 28.82 976.0 29.32 992.9 29.82 1009.8 30.32 1026.8 30.82 1043.7 31.32 1060.6 27.83 942.4 28.33 959.4 28.83 976.3 29.33 993.2 29.83 1010.2 30.33 1027.1 30.83 1044.0 31.33 1061.0 27.84 942.8 28.34 959.7 28.84 976.6 29.34 992.6 29.84 1010.5 30.34 1027.4 30.84 1044.4 31.34 1061.3 27.85 943.1 28.35 960.0 28.85 977.0 29.35 993.9 29.85 1010.8 30.35 1027.8 30.85 1044.7 31.35 1061.6 27.86 943.4 28.36 960.4 28.86 977.3 29.36 994.2 29.86 1011.2 30.36 1028.1 30.86 1045.0 31.36 1062.0 27.87 943.8 28.37 960.7 28.87 977.7 29.37 994.6 29.87 1011.5 30.37 1028.4 30.87 1045.4 31.37 1062.3 27.88 944.1 28.38 961.1 28.88 978.0 29.38 994.9 29.88 1011.9 30.38 1028.8 30.88 1045.7 31.38 1062.6 27.89 944.5 28.39 961.4 28.89 978.3 29.39 995.3 29.89 1012.2 30.39 1029.1 30.89 1046.1 31.39 1063.0 27.90 944.8 28.40 961.7 28.90 978.7 29.40 995.6 29.90 1012.5 30.40 1029.5 30.90 1046.4 31.40 1063.3 27.91 945.1 28.41 962.1 28.91 979.0 29.41 995.9 29.91 1012.9 30.41 1029.8 30.91 1046.7 31.41 1063.7 27.92 945.5 28.42 962.4 28.92 979.3

29.42 996.3 29.92 1013.2 30.42 1030.1 30.92 1047.1 31.42 1064.0 27.93 945.8 28.43 962.8 28.93 979.7 29.43 996.6 29.93 1013.5 30.43 1030.5 30.93 1047.4 31.43 1064.3 27.94 946.2 28.44 963.1 28.94 980.0 29.44 997.0 29.94 1013.9 30.44 1030.8 30.94 1047.7 31.44 1064.7 27.95 946.5 28.45 963.4 28.95 980.4 29.45 997.3 29.95 1014.2 30.45 1031.2 30.95 1048.1 31.45 1065.0 27.96 946.8 28.46 963.8 28.96 980.7 29.46 997.6 29.96 1014.6 30.46 1031.5 30.96 1044.4 31.46 1065.4 27.97 947.2 28.47 964.1 28.97 981.0 29.47 998.0 29.97 1014.9 30.47 1031.8 30.97 1048.8 31.47 1065.7 27.98 947.5 28.48 964.4 28.98 981.4 29.48 998.3 29.98 1015.2 30.48 1032.2 30.98 1049.1 31.48 1066.0 27.99 947.9 28.49 964.8 28.99 981.7 29.49 998.6 29.99 1015.6 30.49 1032.5 30.99 1049.4 31.49 1066.4

Radio Communications 3−3−3

3−3−6. RADIO COMMUNICATIONS TRANSFER

Transfer radio communications by specifying the following:

a. The name of the facility to be contacted and the frequency.

PHRASEOLOGY− CONTACT (name of facility) ON (frequency).

b. In situations where an aircraft will continue to communicate with your facility, use the following:

PHRASEOLOGY− CONTACT (name of service) ON (frequency).

3−3−7. ATC CLEARANCES, ADVISORIES, OR REQUESTS

a. Notify ATC via interphone of a pilot’s request for clearance and include the departure and destination airports and, if appropriate, departing runway and time in the request. Forward pilot requests to execute the Visual Climb Over Airport (VCOA) procedure to ATC. Relay, verbatim, ATC clearances, advisories, and requests received from the control facility. Give a time check to the nearest quarter minute when relaying a clearance that includes a release or void time.

NOTE− For ATC clearances, “verbatim” means exact control instructions in the format stated in FAA Order JO 7110.65, Air Traffic Control, Chapter 4, Section 2, Clearances, and Section 3, Departure Procedures.

PHRASEOLOGY− Aircraft on the ground:

(ARTCC facility’s name) Center FLIGHT DATA, CLEARANCE REQUEST or

(Facility) RADIO, CLEARANCE REQUEST.

After go−ahead from ATC,

(Aircraft identification) DEPARTING (airport), RUNWAY (number if applicable) DESTINATION (fix or airport). (If applicable), CAN BE OFF AT (time).

Aircraft airborne:

(Facility) RADIO, CLEARANCE REQUEST.

After go−ahead from ATC:

(Aircraft identification), (position), (altitude), (route), AND (destination).

b. Prefix all ATC clearances, advisories, or requests with the appropriate phrase “A-T-C CLEARS,” “A-T-C ADVISES,” etc.

c. When issuing information, relaying clearances, or instructions, ensure acknowledgement by the pilot.

d. If altitude, heading, or other items are read back by the pilot, ensure the readback is correct. If incorrect or incomplete, make corrections as appropriate.

NOTE− Pilots may acknowledge clearances, instructions, or information by using “Wilco,” “Roger,” “Affirmative,” or other appropriate words or remarks.

REFERENCE− P/CG.

3−3−8. DEPARTURE REPORTS

a. When an IFR aircraft reports airborne or is observed airborne, transmit the aircraft identification and departure time to the control facility from which the clearance was received.

PHRASEOLOGY− (Facility) RADIO. DEPARTURE. (Aircraft identification), (time). NOTE− 1. This includes known VFR departure times of aircraft which are to obtain IFR clearances when airborne. 2. The requirement for transmitting departure reports may be omitted if requested by the IFR control facility, provided the procedures are specified in a Letter of Agreement.

b. When an aircraft which has filed an IFR flight plan requests a VFR departure, facilitate the request as follows:

1. If the facility/sector responsible for issuing the clearance is unable to issue a clearance, inform the pilot and suggest that the delay be taken on the ground. If the pilot insists upon taking off VFR and obtaining an IFR clearance in the air, relay the pilot’s intentions and, if possible, the VFR departure time to the facility/sector holding the flight plan.

2. After obtaining approval from the facility/ sector responsible for issuing the IFR clearance, an aircraft planning IFR flight may be authorized to depart VFR. Inform the pilot of the proper frequency

3−3−4 Radio Communications

and, if appropriate, where or when to contact the facility responsible for issuing the clearance.

(a) When requesting:

PHRASEOLOGY− (Facility) RADIO. (Aircraft identification), REQUEST V-F-R DEPARTURE.

(b) When relaying to aircraft:

PHRASEOLOGY− A-T-C ADVISES (aircraft identification) V-F-R DEPARTURE APPROVED. CONTACT (facility) ON (frequency) AT (location or time, if required) FOR CLEARANCE.

(c) Relaying to control facility:

PHRASEOLOGY− (Facility) RADIO. (Aircraft identification) DEPARTED V-F-R AT (time).

3−3−9. IFR FLIGHT PROGRESS REPORTS

Relay to the appropriate ATC facility the aircraft identification, position, time, altitude, estimate of next reporting point, name of subsequent reporting point, and any pilot remarks or requests including amended flight plan data.

PHRASEOLOGY− (Facility) RADIO. PROGRESS. (Aircraft identification), (position), (altitude), (time) (name and estimate of next reporting point) (name of subsequent reporting point) (pilot’s remarks).

3−3−10. ARRIVAL/MISSED APPROACH REPORTS

Relay to the appropriate ATC facility, by the most expeditious means available, the time that an IFR aircraft lands, cancels, or executes a missed approach, and intentions, if known.

3−3−11. NONDELIVERY OF MESSAGES

Inform ATC when a message has not been delivered within:

a. Three minutes of receipt; or

b. Three minutes after the specified delivery time; or

c. A specified cancellation time.

3−3−12. BROADCAST (BLIND TRANSMISSION) OF MESSAGES

Broadcast messages as requested by ATC. If no accompanying transmitting instructions are received, transmit the message four times:

a. Once upon receipt; and

b. At approximately 3-minute intervals thereafter.

3−3−13. PENETRATION OF CLASS A AIRSPACE OR PROHIBITED/RESTRICTED AREA

a. Penetration of Class A airspace. When a VFR aircraft’s position report indicates penetration of Class A airspace:

1. Inform the pilot of the Class A airspace penetration and request intentions.

PHRASEOLOGY− YOU ARE IN CLASS A AIRSPACE. AN A-T-C CLEARANCE IS REQUIRED. REQUEST YOUR INTENTIONS.

2. Inform the control facility immediately.

3. Relay ATC instructions.

b. Penetration of PROHIBITED/RESTRICTED AREA. When an aircraft report indicates penetration of a prohibited/restricted area:

1. Inform the pilot.

PHRASEOLOGY− YOU ARE IN A PROHIBITED/RESTRICTED AREA, AUTHORIZATION IS REQUIRED. REQUEST YOUR INTENTIONS.

2. Inform the control facility immediately. Relay ATC instructions.

Radio Communications 3−3−5

Chapter 3. Inflight Services › Section 4. Airport Advisory Services (Alaska Only)

Section 4. Airport Advisory Services (Alaska Only)

3−4−1. TYPES OF AIRPORT ADVISORY SERVICES

Airport advisory services are provided at airports without an operating control tower that have certified automated weather reporting via voice capability. The types of service depend upon the location of the FSS and communications capabilities. There are three types:

a. Local airport advisory (LAA) is a service provided by facilities that are located on the landing airport.

b. Remote airport advisory (RAA) is a remote service which may be provided by facilities that are not located on the landing airport.

NOTE− LAA/RAA both have:

1. Ground-to-air communication on the common traffic advisory frequency (CTAF).

2. Automated weather reporting with voice broadcasting.

3. A continuous automated weather data display.

4. Other continuous direct reading instruments, or manual observations available to the specialist.

c. Remote airport information service (RAIS) is a temporary service provided by facilities which are not located on the landing airport but have:

1. Communication capability.

2. Automated weather reporting available to the pilot at the landing airport.

NOTE− FAA policy requires pilots to access the current automated weather prior to requesting any remote ATC services at non-towered airports. It is the pilot’s responsibility to comply with the Federal Aviation Regulations (FARs) if landing clearance is required.

3−4−2. GENERAL

a. If a pilot asks for airport advisory services at an airport where the requested service is not available but one of the services is available, inform the pilot

about what service is available, and provide the appropriate service.

PHRASEOLOGY− (Airport name) AIRPORT ADVISORY IS NOT AVAILABLE. REMOTE AIRPORT INFORMATION...

b. At airports with commissioned automated weather with continuous automated voice capability, instruct the pilot to monitor the automated broadcast and advise intentions.

PHRASEOLOGY− MONITOR (location) AUTOMATED WEATHER (frequency). ADVISE INTENTIONS.

1. When the pilot indicates receipt of automated weather, provide the appropriate non-weather elements.

2. If the pilot reports the automated weather is out of service, provide the last reported weather available and the appropriate non-weather elements.

c. Advise the pilot that the requested airport advisory/RAIS service is not available. Provide CTAF frequency and/or the automated weather frequency, when available. When not available, issue the last known surface condition and altimeter.

PHRASEOLOGY− (Airport name) AIRPORT ADVISORY or AIRPORT INFORMATION NOT AVAILABLE. CONTACT (airport name) CTAF (frequency).

d. During initial contact, if the pilot indicates receipt of automated weather, provide only the appropriate non-weather elements. Do not provide weather information unless specifically requested by the pilot or a special report is transmitted.

EXAMPLE− RAIS: Pilot - “Green Bay radio, Cessna 12RG, ten northeast, landing Eau Claire, request airport information, I have the automated weather.”

FSS - “Cessna 12RG, Eau Claire airport information, your traffic is a Cessna 172 entering downwind and a Convair 660 reported on final, both one minute ago. There is an airport maintenance vehicle.

e. If additional pilots initiate contact a short time after airport advisory services were provided, determine if the new pilot(s) copied the information when it was provided.

Airport Advisory Services (Alaska Only) 3−4−1

1. If the new pilot responds in the affirmative, do not repeat the information.

2. If the new pilot acknowledges the airport advisory information and then requests specific information, provide only the information requested.

NOTE− The intent is to reduce frequency clutter while insuring that the pilots are aware of the situation as it changes.

f. Final Guard is a service provided in conjunction with airport advisory only during periods of significant and fast changing weather conditions that may affect landing and takeoff operations.

g. Where AFIS is available, confirm receipt of the current AFIS information if the pilot does not initially state the appropriate AFIS code. Issue the current AFIS information to pilots who are unable to receive the AFIS or pilots that do not have the information.

EXAMPLE− “Verify you have information ALPHA.”

h. If the pilot requests special VFR clearance, provide the appropriate elements and follow the procedures in Chapter 3, , Special VFR Operations.

3−4−3. AIRPORT ADVISORY/RAIS ELEMENTS AND PHRASEOLOGY

a. State the airport name and the type of service being provided: airport advisory or airport information.

EXAMPLE− (Airport name), AIRPORT ADVISORY . . .

Or

(Airport name), AIRPORT INFORMATION . . .

NOTE− At FSS facilities with AFIS equipment, if an aircraft has acknowledged receipt of the AFIS message, traffic advisories and additional information need not be preceded by the phrase “(Airport name) AIRPORT ADVISORY.”

b. Provide the following information as needed to best serve the current traffic situation. Do not approve or disapprove simulated instrument approaches.

1. Wind direction and speed.

2. Favored or designated runway is a service provided in conjunction with an airport advisory. The specialist must check the current wind data and provide the favored or designated runway information as follows:

(a) For takeoff and landing operations state the runway most nearly aligned into the wind.

(b) Inform the pilot when the current wind direction is varying enough that the selection of the favored runway may be affected, when there is more than 10 knots between peaks and lulls, or the pilot has requested the information.

(c) If there is no wind, state the runway currently in use, the runway favored by a shorter taxiway, or other local consideration.

(d) When airport management has designated a runway to be used under certain wind or other conditions (and has informed the FSS in writing) issue runway information accordingly.

(e) If the majority of the traffic has been using a runway other than the favored or designated runway, advise the pilot.

EXAMPLE− Landing airport has runways 27 (longer) and 32 with most pilots utilizing the shorter runway “WIND VARIABLE BETWEEN TWO EIGHT ZERO AND THREE FOUR ZERO AT ONE FIVE GUSTS TWO EIGHT, FAVORED RUNWAY THREE TWO.”

(f) When a pilot advises he/she will use a runway other than the favored or the designated runway, inform all known concerned traffic.

PHRASEOLOGY− ATTENTION ALL AIRCRAFT. (Aircraft type) DEPARTING/LANDING RUNWAY (number).

(g) If a pilot requests the distance between an intersection and the runway end, furnish measured data from the local airport intersection takeoff diagram or other appropriate sources.

(h) The favored or designated runway is never provided with RAIS.

3. Altimeter Setting.

(a) Airport Advisory: Apply special procedures when the altimeter setting is more than 31.00 inches Hg. Stations with the capability of reading altimeter settings above 31.00 inches Hg must issue altimeter settings.

3−4−2 Airport Advisory Services (Alaska Only)

JO 7110.10BB 6/17/21 5/19/22 JO 7110.10BB CHG 2

PHRASEOLOGY− ALTIMETER IN EXCESS OF THREE ONE ZERO ZERO. HIGH PRESSURE ALTIMETER SETTING PROCEDURES ARE IN EFFECT. RECOMMEND YOU SET ALTIMETER TO THREE ONE ZERO ZERO EN ROUTE.”

(b) RAIS. Do not provide the altimeter unless specifically requested. Then, provide the altimeter from the last official weather report.

4. Traffic. Information about observed or reported traffic, which may constitute a collision hazard. This may include positions of aircraft inflight and/or aircraft and vehicles operating on the airport.

PHRASEOLOGY− TRAFFIC (Aircraft type), (position), (minutes) AGO.

5. Unmanned aircraft (UA) activity information. Issue UA advisory information for known, observed, or pilot−reported UA activity when, in your judgment, proximity warrants it. If known, include position, altitude, distance, course, and type of UA. For reported UA activity, continue to issue advisories to potentially impacted aircraft for at least 15 minutes following the last report.

EXAMPLE− “Unmanned aircraft activity, 2 miles east of Ketchikan airport, 300 feet and below.”

“Unmanned aircraft activity observed, approximately 1 mile east of Kenai airport, altitude unknown.”

6. Braking action/NOTAM. Furnish braking action reports as received from pilots to all aircraft as follows:

(a) Describe braking action using the terms “good,” “good to medium,” “medium,” “medium to poor,” “poor,” or “nil.” If the pilot reports braking action in other than the approved terms, ask them to categorize braking action in these terms.

(b) When known, include the type of aircraft or vehicle from which the report is received.

EXAMPLE− “Braking action poor.”

“Braking action medium, reported by a Cessna Four−Twenty−One.”

(c) If the braking action report affects only a portion of a runway, obtain enough information from

the pilot to describe braking action in terms easily understood by other pilots.

EXAMPLE− “Braking action poor first half of Runway Six, reported by a Gulfstream Two.”

“Braking action medium Runway Two−Seven, reported by a Boeing Seven Thirty−Seven.”

NOTE− Descriptive terms, such as first/last half of the runway, should normally be used rather than landmark descriptions, such as opposite the fire station, south of a taxiway.

7. NOTAM. NOTAMs concerning local NAVAIDs and local field conditions/airspace conditions pertinent to flight, for example, local NAVAIDs, TFRs.

EXAMPLE− “All runways covered by packed snow 6 inches deep.”

8. Weather. When the pilot does not have the weather conditions, issue the last reported or known weather information as follows:

(a) Airport Advisory/RAIS:

(1) Wind direction and speed.

(2) Altimeter (except RAIS).

(3) Ceiling and visibility to VFR aircraft when less than basic VFR conditions exist.

(4) Visibility to VFR aircraft when it is less than three miles in any quadrant.

(5) Touchdown runway visual range (RVR)/runway visibility value (RVV) for the runway in use where RVR/RVV readout equipment is located at the workstation providing the service.

(6) To IFR aircraft executing an instrument approach or departure and to the appropriate control facility when visibility is less than 3 miles or when the ceiling is less than 1,000 feet or below the highest circling minimum, whichever is greater.

9. Weather advisory alert. Provide in accordance with subparagraph 3−3−5a.

PHRASEOLOGY− (Advisory description) IS CURRENT FOR (condition) OVER (area).

10. Density Altitude.

(a) Facilities at airports with field elevations of 2,000 feet MSL or higher, transmit a density

Airport Advisory Services (Alaska Only) 3−4−3

JO 7110.10BB 6/17/21 3/15/07 7110.65R CHG 2 JO 7110.10BB CHG 2 5/19/22

altitude advisory to departing general aviation aircraft whenever the temperature reaches the criteria contained in TBL 3−4−1.

TBL 3−4−1 Density Altitude

Field Elevation Temperature (C) 2,000−2,999 29 degrees or higher 3,000−3,999 27 degrees or higher 4,000−4,999 24 degrees or higher 5,000−5,999 21 degrees or higher 6,000−6,999 18 degrees or higher 7,000−higher 16 degrees or higher

PHRASEOLOGY− CHECK DENSITY ALTITUDE.

(b) Omit this advisory if pilot states the computation has been done or if the specialist is aware that a density altitude computation for that aircraft was included in the preflight briefing.

11. Wake Turbulence. Issue cautionary information to any aircraft if in your judgment wake turbulence may have an adverse effect on it.

PHRASEOLOGY− CAUTION, WAKE TURBULENCE (traffic information).

NOTE− Wake turbulence may be encountered by aircraft in flight as well as when operating on the airport movement area. Because wake turbulence is unpredictable, air traffic personnel are not responsible for anticipating its existence or effect.

12. Final Guard is a wind and altimeter monitoring service provided in conjunction with airport advisory during periods of significant and/or fast changing weather conditions that may affect landing and takeoff operations. The specialist must monitor the remote display of the current wind and altimeter. Provide Final Guard as follows:

(a) When the pilot reports “On final” or “Taking the active runway,” the specialist must provide the current wind direction, speed, and altimeter.

(b) If during the landing or takeoff operation conditions change and, in the specialist’s opinion, the changing information might be useful to the pilot, the specialist must broadcast the new wind and/or altimeter information in the blind.

(c) Pilots will not be required or expected to acknowledge the broadcast.

EXAMPLE− “N12RG, Wind (direction) at (speed).” NOTE− Final Guard is never provided with RAIS.

13. Upon request, provide runway condition codes (RwyCC) as received from airport management to aircraft as follows: State the runway number followed by the runway condition code for each of the three runway zones and the time of the report in UTC. Issue FICON NOTAMs upon pilot request.

EXAMPLE− “Runway two seven, condition code two, two, one at one zero one eight ZULU.”

Continue reading ↓ 120 of 1421 passages shown