Radar Vectors
FAA Order Current Issued May 31, 1983 AJM-231 287 pages Copy saved Nov 18, 2026

Order 6340.15 Primary/secondary En Route Radar Siting Handbook

This handbook establishes specific procedures which are to be observed in selection of sites for Air Route Surveillance Radar/Air Traffic Control Radar Beacon Interrogator (ARSR/ATCBI) en route facilities.

Official source ↗ Open PDF

Text read by OCR from a scanned file (10 of 287 pages). Check the original, as some words may be misread.

ORDER /L?*D.Ls

PRmY/SECONDARY EN ROUTE RADAR SITING HANDliOOK

May 31, 1983

DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

Distribution: A-W (PM/AT/ES/FO)-3;A-X(AF/AT/FS)-3; initiated By: APM-300 A-Y(AE)-2; AAC-440(3)

5/31/83

FOREWORD

This order establishes procedures and responsibility for assuring the optimum selection of sites for new FAA en route air traffic control radar

FEDERAL AVIATION ADMINISTRATION

facilities. In the interests of completeness and to minimize the need for reference to other material, the order also contains background explanatory information covering the current en route radar equipment and all applicable siting criteria.

The material contained in this order is organized into four chapters: (1) general introduction, (2) equipment considerations, (3) ARSR and ATCRBS siting criteria, and (4) siting procedures. Several explanatory and/or supplementary appendices are also included.

and Maintenance Service

Page i (and ii)

5/31/83 6340.15

TABLE OF CONTENTS

TABLE OF CONTENTS

CHAPTER 1. GENERAL INTRODUCTION

1.

f : 4. 5. 6. 7. 8'. 9. 10.

Purpose. 1 Distribution, 1 Cancellations. 1 Background. 1 Responsibility and Authority. 1 Related Documents. 1 Application. 1 Scope. 2 Handbook Organization. 2 Revision of Material. 2

CHAPTER 2. EQUIPMENT CONSIDERATIONS

SECTION 1. INTRODUCTION 3 11. Introduction 3

SECTION 1. INTRODUCTION 3 11. Introduction 3

SECTION 2. AIR ROUTE SURVEILLANCE RADAR 3 12. Function. 3 13. Equipment Parameters. 4 14. Area Coverage. 4 15. Vertical Coverage. 4 16. Characteristics Pertinent to Site Selection 4 17-19. Reserved 24

SECTION 3. AIR TRAFFIC CONTROL RADAR BEACON SYSTEM. 25 20. Function 25 21. Equipment Parameters. 26 22. Area Coverage. 26 23. Characteristics Pertinent to Site Selection 26

SECTION 4. ANCILLARY EQUIPMENT, 50 24. Transmitter/Receiver Building. 50 25. Radar Tower. 50 26. Electrical Power Facilities. 50 27. Remoting Equipment. 50 2 8 . Height-Finder Radar. 52 29. Electrical Grounding System. 52 30. Reserved 52

Page No.

1

3

Page iii

6340.15 5/31/83

CHAPTER 3. ARSR AND ATCRBS SITING CRITERIA

CHAPTER 3. ARSR AND ATCRBS SITING CRITERIA

SECTION 1. INTRODUCTION. 31. Introduction.

SECTION 2. CCVEIWGE FACTORS AND FACILITY REQUIREMENTS. 32. General. 33. Coverage Factors, 34. ATC Facility Operational Requirements,

SECTION 3. ARSR/ATCRBS COVERAGE CAPABILITIES 56 35. Introduction 56 36. ARSR Coverage 57 37. ATCBI Coverage 58

SECTION 4, OPERATIONAL LIMITATIONS 62 38. Introduction. 62 39. Degraded Performance Effects. 64 40. Sources/Causes of Degraded Performance. 137

SECTION 5. SITE REQUIREMENTS/LIMITATIONS 154 41. Introduction. 154 42. Environmental Impact Assessment. 154 43. Components of Average Facility, 154 44. Land Acquisition. 155 45. Access Road. 155 46. Road Construction. 156 47. Clearing/Grading/Landscaping. 156 48. Site Security. 156 49. Utilities. 157 50. Reserved.' 157

CHAPTER 4. SITING PROCEDURES

CHAPTER 4. SITING PROCEDURES

SECTION 1. INTRODUCTION

51. Major Tasks. 52. Specific Activities.

SECTION 2. PRELIMINARY DATA ACQUISITION

53. General 159 54. Airspace Coverage Requirements 165

55. Maps and Charts 165

56. Local Climatological Data. 167

57. Standard FAA Drawings and Specifications. 167

55. Maps and Charts 165

Page No.

53

53 53

53 53 54 55

159

159

159 159

159

Page iv

5131183 6340.15

SECTION 3. PRELIMINARY SITE SELECTION

58. Introduction. 167 59. Determine Siting Area Boundaries. 167 60. Preliminary Site Inspection. 175 61. Preliminary Site Analysis, 179 62. Selection of Sites for Survey. 180

SECTION 3. PRELIMINARY SITE SELECTION

SECTION 4. SITE SURVEY.

63. Introduction. 182 64. Pre-Survey Coordination. 182 65. Equipment Needs. 183 66. Scaffold Assembly. 184 67. Screening Profile Measurements. 184 68. Survey Procedures. 187 69. Panoramic Photographs. 189

70. Additional Data for Electronic Assessment. 190

71. Environmental Data. 192 72. Cost Data 193

SECTION 5. SITE PERFORMANCE ANALYSIS.

73. General. 194 74. Site Panoramic Photograph. 195 75. Screening Analysis. 195 76. LOS Altitude Coverage Analysis. 202 77. ARSR Coverage Analysis. 206 78. Beacon Coverage Analysis. 208 79. Vertical Lobing Analysis 213

80.. False Target Analysis. 219 81. Clutter Analysis. 220 82. Tangential Course Analysis. 225 83. Second-Time-Around Analysis. 228

SECTION 6. SITE ENVIRONMENTAL ANALYSIS.

84. General. 85. Responsibility. 86. Procedures.

SECTION 7. COST ANALYSIS. 230

SECTION 7. COST ANALYSIS. 230

87. General. 230 88. Cost Items. 230 89. . Cost Estimate Preparation. 232

90. Supplementary Analyses. 232

91. Cost Summary. 233

Page No.

167

182

194

229

229 229 229

Page v

6340.15 5/31/83

Page No.

SECTION 8. SITING REPORT. 233

92. Purpose and Scope. 233 93. Report Content and Organization. 233 94. Distribution. 233

SECTION 9. FINAL SITE SELECTION. 233

SECTION 9. FINAL SITE SELECTION. 233

95. Review and Coordination. 233 96. Concurrence. 235

Appendix 1: REFERENCES (1 page)

Appendix 2: DATA FORMS (14 pages)

APPENDIX 3: COMPUTER PROGRiM FOR RADAR LINE-OF-SIGHT PLOTS

APPENDIX 4: OUTLINE OF SITING REPORT (5 pages)

APPENDIX 5: GLOSSARY (3 pages)

APPENDIX 5: GLOSSARY (3 pages)

1

(10 pages) 1

1

1

APPENDIX 6: USER'S GUIDE TO THE FAA RADAR COVERAGE TIME SHARE 1 PROGRAM (10 pages)

INDEX (3 pages) 1

Page vi

5131183 6340.15

Figure No.

LIST OF FIGURES

Page No.

6

8

9

12

2-l

2-2

2-3

2-4

2-5

2-6

2-7

2-8

2-9

2-10

2-11

2-12

2-13

2-14

2-15

2-16

2-17

2-18

2-19

FREE SPACE ARSR-3 COVERAGE OF T-33 AIRCRAFT

TYPICAL ARSR-3 AND MERF FREE-SPACE ANTENNA AZIMUTH PATTERN

TYPICAL ARSR-3 AND MERF FREE-SPACE ANTENNA AZIMUTH PATTERN

TYPICAL ARSR-3 AND MERF FREE-SPACE ANTENNA ELEVATION PATTERN

ARSR-3 ANTENNA DESIGN PATTERN

SIGNAL-TO-CLUTTER IMPROVEMENT PROVIDED BY USE OF ARSR-3 PASSIVE ANTENNA HORN

FREE SPACE ARSR-3 COVERAGE OF T-33 AIRCRAFT UPPER BEAM VERSUS LOWER BEAM RECEPTION

RANGE AMBIGUITY POINTS

RANGE AMBIGUITY POINTS

HITS/SCAN VS PRF FOR ARSR-3 EQUIPMENT

RESPONSE OF ARSR-3 MT1 RECEIVER RELATIVE TO NORMAL (LOG CFAR) RECEIVER

ATCRBS MAXIMUM RANGE COVERAGE (ATCBI-5)

TYFICAL FREE-SPACE AZIMUTH PATTERN FOR ATCBI DIRECTIONAL ANTENNA WITH ARSR-3 REFLECTOR

TYPICAL FREE-SPACE ELEVATION PATTERN FOR ATCBI DIRECTIONAL ANTENNA WITH ARSR-3 REFLECTOR

TYPICAL VERTICAL PATTERN OF ATCBI OMNIDIRECTIONAL ANTENNA USED WITH ARSR-3

TYPICAL VERTICAL PATTERN OF ATCBI OMNIDIRECTIONAL ANTENNA USED WITH ARSR-3

TYPICAL FREE SPACE ELEVATION RADIATION PATTERN FOR FfVE=FOOT LIGHT-WEIGHT HIGH GAIN ARRAY TO BE USED WITH EN ROUTE DABS

TYPICAL FREE SPACE AZIMUTH RADIATION PATTERN FOR FIVE-FOOT LIGHT-WEIGHT HIGH GAIN ARRAY TO BE USED WITH EN ROUTE DABS

INTERROGATION PULSE SPACINGS FOR ATCBI MODES

INTERROGATION PULSE SPACINGS FOR ATCBI MODES

EXAMPLES OF ATCRBS REPLY PULSE CODES

PPI TIME EXPOSURE FOR A RADIAL FLIGHT SHOWING RING-AROUND EFFECTS

SIDE-LOBE SUPPRESSION SYSTEM (SLS) AMPLITUDE RELATIONSHIPS AND ANTENNA PATTERNS

13

14

17

19

22

28

29

30

32

33

34

36

37

40

40

Page vii

SIDE-LOBE SUPPRESSION SYSTEM (SLS) AMPLITUDE RELATIONSHIPS AND ANTENNA PATTERNS

Figure No.

5/31/83

2-20

2-21

2-22

2-23

2-24

2-25

2-26

2-27

3-l

3-2

3-3

3-4

3-5

3-6

3-7

3-8

3-9

3-10

3-11

3-12

3-13

3-14

EFFECT OF REFLECTED-PATH BEACON OPERATION

SUCCESSFUL SLS ACTION AGAINST REFLECTED PATH INTERROGATION

TRANSPONDER INPUT PULSE AMPLITUDE DIAGRAMS SHOWING UNSUCCESSFUL SLS ACTION AGAINST REFLECTED PATH INTERROGATION

ISLS VS. SLS COMPARISON

ISLS VS. SLS COMPARISON

MAXIMUM ISLS EFFECTIVENESS RANGE

LIMITS FOR SLS/ISLS FALSE TARGET SUPPRESSION WITH REFLECTED PATH DELAY < 35 psec

SLS/ISLS FALSE TARGET SUPPRESSION CAPABILITIES FOR PATH DELAYS < 2 psec -

ARSR-3 SITE LAYOUT

ARSR-3 RANGE COVERAGE, LOWER BEAM RECEPTION

ARSR-3 RANGE COVERAGE, UPPER BEAM RECEPTION

ATCBI-5 RANGE COVERAGE CAPABILITY

ATCBI-5 RANGE COVERAGE CAPABILITY

CURVED EARTH SCREENING

OBSTACLE SCREENING

BENDING OF ANTENNA BEAM BECAUSE OF REFRACTION

(TRUE EARTH RADIUS, a)

SHAPE OF ANTENNA BEAM IN EQUIVALENT-EARTH REPRESENTATION

(RADIUS = 4/3 a)

LOS DISTANCE VS. ANTENNA HEIGHT

SCREENING ANGLE VS. RANGE

RADAR-OPTICAL SCREENING ANGLE CORRECTION

DIFFERENCE BETWEEN OPTICAL AND RADAR SCREENING

DIFFERENCE BETWEEN OPTICAL AND RADAR SCREENING

TYPICAL VERTICAL RADIATION PATTERN WITH GROUND REFLECTION

VERTICAL LOBING PATH GEOMETRY

NULL ANGLES AT 1300 MHz

Page No,

41

42

43

45

46

47

48

51

60

61

63

65

66

67

67

69

70

73

75

77

78

82

Page viii

5131183

Figure No,

3-15

3-16

3-17

3-18

NULL ANGLES AT 1300 MHz

3-19

3-20

3-21

3-22

3-23

3-24

3-25

3-26

3-27

3-28

3-29

3-30

3-31

3-32

3-33

3-34

3-35

3-36

3-37

3-38

NULL ANGLES AT 1030 MHz

MINIMUM VALUE OF EARTH GAIN FACTOR (D)

LOBE PEAR ANGLES AT 1300 MHz

LOBE PEAR ANGLES AT 1030 MHz

MAXIMUM VALUE OF EARTH GAIN FACTOR (n)

ANTENNA HEIGHT FOR LOBING CALCULATIONS

ANGULAR RELATIONSHIPS FOR NULL DEPTH DETERMINATION

ANGULAR RELATIONSHIPS FOR NULL DEPTH DETERMINATION

TILT ANGLE EFFECT ON ATCBI-5 NULL

TILT ANGLE EFFECT ON ATCBI-5 NULL

TILT ANGLE EFFECT ON ATCBI-5 NULL

TILT ANGLE EFFECT ON ARSR-3 (LOWER BEAM) NULL

TILT ANGLE EFFECT ON ARSR-3 (LOWER BEAM) NULL

TILT ANGLE EFFECT ON ARSR-3 (LOWER BEAM) NULL

TILT ANGLE EFFECT ON ARSR-3 (UPPER BEAM) NULL

TILT ANGLE EFFECT ON ARSR-3 (UPPER BEAM) NULL

TILT ANGLE EFFECT ON ARSR-3 (UPPER BEAM) NULL

TILT ANGLE EFFECT ON ARSR-3 (UPPER BEAM) NULL

EFFECT ON LOBE PATTERN CAUSED BY VARIATION IN ANTENNA HEIGHT ARSR-3, LOWER BEAM RECEPTION

EFFECT ON LOBE PATTERN CAUSED BY VARIATION IN ANTENNA TILT ANGLE ARSR-3, LOWER BEAM RECEPTION

SURFACE ROUGHNESS CRITERION

SURFACE ROUGHNESS CRITERION

FIRST NULL REFLECTION POINT LOCATION (ARSR EQUIPMENT)

SECOND NULL REFLECTION POINT LOCATION (ARSR EQUIPMENT)

THIRD NULL REFLECTION POINT LOCATION (ARSR EQUIPMENT)

FIRST NULL REFLECTION POINT LOCATION ATCBI EQUIFMENT

SECOND NULL REFLECTION POINT LOCATION ATCBI EQUIPMENT

SECOND NULL REFLECTION POINT LOCATION ATCBI EQUIPMENT

Page No.

83

84

85

86

87

89

91

92

93

94

95

96

97

98

99

100

101

102

104

106

107

108

109

110

Page ix

3-39

3-40

3-41

3-42

3 - 4 3 a

3-43b

3-44

3-45

3-46

3-47

3-48

3-49

4-1

4-2

4-3

4-4

4-5

4-6

4-7

4-8

4-9

4-10

6340.15 5/31/83

Figure No.

THIRD NULL REFLECTION POINT LOCATION-ATCBI EQUIPMENT

MAGNITUDE OF REFLECTION COEFFICIENT

MAGNITUDE OF REFLECTION COEFFICIENT

PHASE OF REFLECTION COEFFICIENT

CLUTTER PATH-GEOMETRY

BEACON REFLECTION NOMOGRAPH- EFFECTIVE AREA DETERMINATION

BEACON REFLECTION NOMOGRAPH- MAXIMUM RANGE DETERMINATION

BEACON FALSE-TARGET ANGULAR GEOMETRY

TANGENTIAL PATH GEOMETRY

MAXIMUM COVERAGE DROPOUT DUE TO TANGENTIAL TARGETS

COVERAGE DROPOUT REGION

COVERAGE DROPOUT REGION

TIME VS. DISTANCE FOR COVERAGE DROPOUT

COMPARISON BETWEEN HIGH-SITED, LOW-SITED RADAR/BEACON

MAJOR SITING TASKS

SITING TASK MATRIX

ARSR/ATCBI SITING MANAGEMENT PLAN

Page No.

111

113

114

119

127& 128

129& 130

131

134

135

136

138

139

160

161C 162

163& 164

DETERMINATION OF SITING LAND AREA AS A FUNCTION OF ARSR/ATCBI COVERAGE AND FIX DISTRIBUTION

WORKSHEET FOR PRELIMINARY RADAR COVERAGE ESTIMATION

WORKSHEET FOR PRELIMINARY RADAR COVERAGE ESTIMATION

169

171

ILLUSTRATION OF REDUCTION IN RANGE COVERAGE CAPABILITY AS A FUNCTION OF FIX ALTITUDE 173

ILLUSTRATION OF LAND ELIMINATION TECHNIQUE BASED ON CONE-OF-SILENCE

PRELIMINARY SITE INSPECTION CHECKLIST

174

177-178

ILLUSTRATION OF CLOSE-IN AND DISTANT OR SKYLINE SCREEN PROFILES

ILLUSTRATION OF DIFFERENCE BETWEEN LOW-ANGLE AND DISTANT OR SKYLINE SCREEN PROFILES

ILLUSTRATION OF DIFFERENCE BETWEEN LOW-ANGLE AND DISTANT OR SKYLINE SCREEN PROFILES

185

186

Page.x

5/31/83 6340.15

l

Figure No.

4-11

4-12

4-13

4-14

4-15

4-16

4-17

4-18

4-19

4-20

4-21

4-22

4-23

4-24

4-25

4-26

SCREEN ANGLE SURVEY DATA SHEET

SECTOR OF SITE PANORAMIC PHOTOGRAPH FOR BEACH NORTH DAKOTA SITE "A"

SCREEN ANGLE GRAPH

SCREEN ANGLE GRAPH

LOS COVERAGE WORKSHEET

POLAR COVERAGE CHART

RADAR LOS ALTITUDE RANGE CUTOFF WORKSHEET

RADAR LOS COVERAGE DIAGRAM

RADAR COVERAGE INDICATOR (RCI) CHART

RCI OVERLAY CHART, ARSR-3, LP-CLEAR

RCI OVERLAY CHART, ARSR-3, CP-CLEAR

RCI OVERLAY CHART, ARSR-3, CP-HEAVY RAIN

RCI OVERLAY CHART, ATCBI-5

RCI OVERLAY CHART, ATCBI-5

EXAMPLE OF FALSE TARGET ANALYSIS

ILLUSTRATION OF TANGENTIAL COURSE ANALYSIS

COST ESTIMATE FORM FOR ARSR/ATCBI SITE ANALYSIS

SUMMARY OF COSTS FOR THREE PROSPECTIVE SITES FOR THE BEACH NORTH DAKOTA EN ROUTE RADAR

APPENDIX 3

3-l RADAR LOS BOUNDARY DIAGRAM

3-2 RADAR COVERAGE INDICATOR CHART

3-2 RADAR COVERAGE INDICATOR CHART

APPENDIX 6

6-1 SAMPLE DATA INPUT SET

6-2A ANTENNA GAIN TABLE

6-2B OTHER INPUT DATA

6-2C CALCULATED VALUES

6-3 S/N VS RANGE/ALTITUDE/ANTENNA

Page No.

188

196

197

199

203

205

207

209

210

211

212

214

221

227

231

234

3

4

7

8

9

9

1 0

Page xi

6340.15 5/31/83

LIST OF TABLES

LIST OF TABLES

Table No.

2-l

2-2

2-3

3-l

3-2

3-3

3-4

3-5

3-6

4-l

4-2

4-3

4-4

ARSR-3 PARAMETERS

ATCBI-5 PARAMETERS AND FEATURES

ATCRBS TRANSPONDER REPLY CODES

TYPICAL AIRCRAFT AVERAGE CROSS SECTION

TERRAIN REFLECTION CHARACTERISTICS

LAND CLUTTER REFLECTIVITY

NORMALIZED MEAN SEA BACKSCATTER COEFFICIENT, Go

RAIN BACKSCATTER AT 1230 MHz

RAIN BACKSCATTER AT 1230 MHz

ATMOSPHERIC CONTAMINANTS

Page No.

5

27

38

59

116

120

121

148

150

FRESNEL ZONE PARAMETERS 216

BEACH NORTH DAKOTA SITE NULL REFLECTION POINT, GRAZING ANGLE, AND CRITICAL HEIGHT 216

POTENTIAL COVERAGE PROBLEMS FOR BEACH NORTH DAKOTA NAVIGATIONAL FIXES DUE TO LOBING 218

MAXIMUM ANTENNA SWITCHING RANGE FOR ARSR-3 223

MAXIMUM ANTENNA SWITCHING RANGE FOR ARSR-3 223

Appendix 6

,6-l Explanation of Variables 6

Page xii

5131183 6340.15

CHAPTER 1. GENERAL INTRODUCTION

1.. PURPOSE. This handbook establishes specific procedures which are to be observed in selection of sites for Air Route Surveillance Radar/Air Traffic Control Radar Beacon Interrogator (ARSR/ATCBI) en route facilities. These procedures are necessary to assure uniform and objective comparison of candidate radar sites and to permit selection of an optimum site.

CHAPTER 1. GENERAL INTRODUCTION

2. DISTRIBUTION. This directive is distributed to branch level in the Program Engineering and Maintenance, Systems Engineering, and Air Traffic Services and the Office of Flight Operations in Washington headquarters; to branch level in the regional Airway Facilities, Air Traffic, and Flight

Standards divisions; and to the Engineering and Production Branch and the Airway Engineering Support Division at the Aeronautical Center.

3. CANCELLATIONS. FAA Order 6340.7, Long Range Radar ARSR Facility Siting Procedure Handbook, is canceled.

4. BACKGROUND. This handbook was prepared to meet the need for a clear and concise statement of the procedures to be followed in selection of sites for new en route ARSR/ATCBI installations. Observance of these procedures will allow superior future site selection at a lower net long-term cost to the FAA. The material was prepared by IIT Research Institute under contract to FAA, after a careful review of regional site selection practices.

5. RESPONSIBILITY AND AUTHORITY. In order to assure that selected sites meet the needs of the agency,maximumattention shall be given to the selec-

tion of a radar site. A group shall be established in the Program Engineering and Maintenance Service (APM) to be the focal point for siting data. The Service will chair a group composed of regional, AAT, and APM personnel to review, analyze, and recommend site locations. The Mrector, APM, shall be the final approving authority for radar surveys. Development of.the operational requirements shall basically be a regional responsibility. AAT shall be the focal point for operational requirements and shall establish a group consisting of regional and headquarters personnel to review and recommend the final operational requirements. The procedures for establishing the groups to coordinate operational requirements and site selection are specified in the latest edition of Order 6300.5, Enroute Radar And Beacon Siting Procedures .' Responsibilitleu, And App'rtiuals; The Lirector of the Air Traffic Service shall be the final approving authority for operational requirements.

6. RELATED DOCUMENTS, The information contained in this handbook was obtained from previous FAA en route and terminal radar siting documents, FAA headquarters-and regional engineering personnel, FAA technical specifications and manuals, and other more general sources. Specific document references are made in the text, with a complete reference index at the end of the handbook.

Chap 1 Par 1 Page 1

6340.15 5/3l/83

7. APPLICATION. The information presented in this handbook is intended primarily for the siting of new FAA en route radar facilities, but may also be applied to facilities modification/relocation and to the correction of siting problems.

8. SCOPE.

a. Equipment. This handbook covers site selection and report preparation for the ARSR-3 and the ATCBI-5 equipments. With comparatively minor modifications, however, it should also be applicable to bther FAA long range

radar equipment.

b. Limitations. Because of the simplifying assumptions used in order to reduce the equations and charts contained in this document to readily usable form, the user should be aware that coverage predicted by the techniques described herein will necessarily be only a close approximation to the actual coverage obtainable from a given installation. The principal value of the selection techniques presented is as a realistic yardstick for comparison of the various sites under consideration.

9. HANDBOOK ORGANIZATION.

a. Chapter 2 of this handbook summarizes the operational performance achievable with the ARSR-3 and otheren route radars and with the accompanying ATCBI-4, 5 radar beacon equipments in idealized, free-space situations. It also discusses the significance.of equipment characteristics as related to site selection.

b. Chapter 3 presents a fairly detailed discussion of ARSR and ATCRBS siting criteria including coverage and facility requirements, coverage capabilities, operational limitations, and site requirements and limitations.

C . Chapter 4 provides a step-by-step radar siting procedure including preliminary data acquisition, preliminary site selection, site survey, and detailed site analysis.

10. REVISION OF MATERIAL. Revision of the material in this handbook will be made periodically as required. Forward any recommendations for changes to this directive through normal channels to the Comunications and Surveillance Mvision, APM-300, Program Engineering and Maintenance Service.

Page 2

Chap 1 Par 8 0

5/31/83 6340.15

CHAPTER 2. EQUIPMENT CONSIDERATIONS

CHAPTER 2. EQUIPMENT CONSIDERATIONS

SECTION 1. INTRODUCTION

11. INTRODUCTION. This chapter of the ARSR/ATCBI siting handbook constitutes a short review of the operation of air traffic control equipment commonly installed aten route radar sites. Topics to be covered include a brief description of system functions together with a discussion of those system characteristics and parameters which are important to site selection or siting data analysis. It should be noted, however, that this chapter is not intended as a comprehensive general treatment of radar and beacon system operation, but rather as a brief highlighting of those ARSR and ATCBI features important to site selection. For more detailed textbook treatment the reader is referred to references 1 and 2.

SECTION 2. AIR ROUTE SURVEILLANCE RADAR

SECTION 2. AIR ROUTE SURVEILLANCE RADAR

12. FUNCTION.

a. General. A surveillance radar consists basically of an antenna, a transmitter, a receiver, an automated data processor, and a display. The transmitter generates short pulses of radio energy which are radiated into space by,the antenna. A small portion of this energy is returned to the radar after striking reflecting objects. Echo energy picked up by the antenna is sent to the radar receiver and automated processor for amplification, detection, and special data processing. It is then displayed visually for operational purposes, as well as perhaps being processed in other ways. Since radar energy travels at the speed of light, distance to the reflecting object can be determined on the basis of time required for the radar pulse to travel to and from the object. The bearing of the target is determined by the direction in which the antenna beam is pointed when the reflected pulse is received.

b. Air Route Surveillance Radar (ARSR). The Air Route Surveillance Radar (ARSR), as its name implies, is a surveillance radar system designed to detect the presence and location ofen route aircraft. The aircraft reflected signals received by the radar are transmitted to anAir RouteTraffic Control Center (ARTCC), where they are displayed on an indicator for the use of air traffic control personnel, The signals are also automatically supplied to a computer which maintains a record of the present locationsof allaircraft in the region and predicts future locations of the aircraft. The computer uses this data to determine any major deviations from the aircraft's flight plan and, most importantly, to detect any potentially unsafe situation due to insufficient separation of aircraft. Use of ARSR equipment, therefore, is extremely important to the safe, expeditious movement of air traffic.

Chap 2 Par 11 Page 3

6340.15 5/31/83

C . Primary/Secondary Radar Systems. In order to provide increased strength of the aircraft signal for improved detection as well as to transmit additional data such as aircraft identification and aircraft altitude, many aircraft are equipped with radar beacons, However, since not all aircraft are beacon equipped, reliance must be placed on the surveillance radar, and there-

fore the ARSR is designed as the PRIMARY RADAR to distinguish its functions from otheren route radar equipment. The radar beacon system is often referred to as the SECONDARY RADAR, While this latter designation may be subject to alteration as more sophisticated radar beacons assume a larger role in air traffic control, the nature of ARSR equipment is such that it will probably always be required. A surveillance radar is the only type of system capable of providing information on the presence and location of non-beacon equipped aircraft in the controlled airspace.

13. EQUIPMENT PARAMETERS. Currently, the FAA utilizes Air Route Surveillance Radars designated as ARSR-1, ARSR-2, ARSR-3, MERF (Mobile Enroute Radar Facility), AN/FPS-20, and AN/FPS-60. The ARSR-l/2 and the AN/FPS-20/60 are older equipments which are gradually being replaced, and no further siting of these radars is anticipated. They are not covered in this handbook, nor is MERF equipment. The latter system is used for temporary or emergency ATC purposes, but is not a subject for permanent site ,establishment, The handbook, there-

fore, is intended for siting the ARSR-3 or subsequent new radar equipment. The important parameters of the ARSR-3 are tabulated below in table 2-l.

14. AREA COVERAGE. The ARSR is capable of detecting aircraft which are within its line-of-sight as the antenna rotates azimuthally through 360 degrees. The precise region of area coverage provided by an ARSR is dependent upon

(a) the parameters of the particular radar, (b) the target being detected, and (c) the nature of the radar site.

15. VERTICAL COVERAGE. Each ARSR is used for detection and tracking of aircraft overflying its control area as well as aircraft whose flights originate and/or terminate within the control area. It is'important, therefore, that the ARSR provide coverage throughout a wide range of altitudes. A typical vertical coverage chart for the ARSR-3 for idealized conditions is given in figure 2-l. This includes the effect of atmospheric attenuation, but not the effect of precipitation nor the effect of ground reflection. More detailed coverage charts are presented in chapter 3.

16. CHARACTERISTICS PERTINENT TO SITE SELECTION.

a. Antenna Coverage. The function of the ARSR antenna system is to radiate the transmitter output energy into a directional beam, and receive the returning echo energy, passing it on to the receiver with a minimum of loss. An electronic switching technique is used to switch the antenna from transmitter to receiver, thereby facilitating operation and providing protection against receiver overload during the time of pulse transmission (nominally 0.06 percent of the pulse repetition period).

Page 4

Chap 2 Par 12

5/31/83

Table 2-l

ARSR-3 PARAMETERS

ARSR-3 PARAMETERS

634i?. 1s

Vominal PPI Range

Accuracy

Azimuth Range Resolution

Azimuth Range Antenna

Main (low beam)

Pattern Shape Beamwidth

Azimuth Elevation Max. Gain dBir Scan Rate Polarization Passive (high beam)

Pattern Shape Beamwidth

Azimuth Elevation Max. Gain dBir Polarization RF Frequency MHz PRF Pps Peak Power Output MW Pulse Duration MS

Receiver Noise Figure (dB)

Sensitivity (dBm)

Log (Log/CFAR/AntiLog) MT1 (I and Q, Log/CFAR/AntiLog) MT1 (I or (2, Log/CFAR/AntiLog) WEA e%) WEA (MIT/Log/AntiLog) Normal MT1 Log MT1 Improvement Factor (dB) Antenna Tilt Capability

20'* nmi

+ 0.180 + 178 nmi, .005 R -

20 .25 nmi

mod CSC28

1.10 min 3.60 min 34.5 5 rpm LP/CP

mod CSC20

0.9"- 1.10 3.60 min 33.5 LP/CP 1250-1350 310-365 L' 5 2

4.0

-115 -112 -112 -113 -112 -114

39 30 to + 30

l&nge of average PRF settings - Between 276 and 399 PPS.

range of instantaneous PRF with VIP is

Chap 2 Par 15 Page 5

Page

=: GUR≤ 2-1 FREE SPACE ARSR-3 COVERAGE OF T-33 AIRCRAFT

=: GUR≤ 2-1 FREE SPACE ARSR-3 COVERAGE OF T-33 AIRCRAFT

6340.15

(Reception on Lower Beam)

(Ft)(

ROdar

Above

COMPUTATIONAL CONDITIONS

Free Space Conditions Including Atmospheric Attenuation Antenna Tilt Angle (Lower 3 dB Point of Main Beam) = 00 Target Cross Section = 2.2 m2 (T-33) Detectfon Probability = 0.8 False Alarm Probability= 10-6 Frequency 1300 MHz IF Bandwidth = 500 kHz PRF = 340 Hz Diplex Operation (Ref. to Table 2.1 for Other Parameters)

COMPUTATIONAL CONDITIONS

neee

10

60

0

100 120 140

110

Chart Based On 4/3 Earth Rodius

100

200

220

140

Range (Nautical Miles)

Par Chap

240

200 5/31/83

5/31/83 6340.15

(1) Antenna Pattern. Probably the most important aspect of an antenna's performance is its directive radiation pattern wherein the transmitted energy is concentrated in some particular direction(s). ARSR antennas produce a fan,beam, narrow in the horizontal or azimuthal direction to provide good azimuthal resolution of closely spaced aircraft, and relatively broad in the vertical direction to detect aircraft within a wide-range of altitudes. Figure 2-2 shows a portion of the horizontal pattern including the main lobe. Figure 2-3 shows a typical vertical pattern, which is a modified csc29 pattern. These two patterns shown are free-space patterns. Due to the effects of the ground and other nearby objects, the actual radiation patterns of installed ARSR antennas will differ from the free-space patterns shown.

(2) Antenna Gain. The gain of an antenna in a given direction is a quantitative measure of the power transmitted in that direction as compared with some reference standard. Normally an isotropic radiator is used as a reference, and antenna gain is given in decibels above the isotropic level

(dBir). Although antenna gain is actually angle dependent., a single number, the maximum value of the antenna's gain, is frequently used to describe antennaperformance. Maximum gain for the ARSR antennas is approximately 34.5 dBir, as indicated iii table 2-1.

(3) Beamwidth,

(a) Azimuthal Beamwidth. The antenna azimuth beamwidth is descriptive for the angular resolution of the ARSR and is measured at the -3 dB points. For Air Traffic Control (ATC) purposes, good azimuth definition is provided by a focused parabolic reflector that concentrates the radiated energy into a narrow azimuthal angle, as shown in figure 2-2. Good azimuth resolution is important in separating targets that are close to each other. All directions are covered by rotating the antenna horizontally at a constant rate.

(b) Elevation Beamwidth. A csc28 vertical pattern is often chosen for the antenna's upper elevation coverage in order that the radar signal power from a given siz.e target flying at a constant altitude be independent of range. However, a radar with a requirement for low-angle coverage will also receive a substantial amount of close-in clutter signal from ground

reflections. While much of this clutter energy can be eliminated by means of moving target indicator (mti) and other techniques, additional clutter reduc-

tion at short ranges can be provided by reducing the receiver sensitivity for the very short ranges, and then gradually increasing the sensitivity during the early portion of each pulse repetition time period. This sensitivity time control (stc), while reducing the clutter, will also reduce the detectability of high-altitude, close-in aircraft unless the antenna's high-angle vertical pattern is modified to compensate for the stc. The ARSR antenna vertical pattern follows the csc20 variation at low angles, but it is modified appropriately at the high angles to compensate for the receiver stc. Accordingly , the vertical pattern is considered to be modified csc28. This modification is evidenced by the plateau region in figure 2-3.

Chap 2 Par 16 Page 7

Fig. 2-2 TYPICAL ARSR-3 AND MERF FREE-SPACE

Fig. 2-2 TYPICAL ARSR-3 AND MERF FREE-SPACE

ANTENNA AZIMUTH PATTERN

0

- 5

-IO

E0

t3 a” -25

-30

-35

Conditions: -

Low Beam

Horizontal Polarization

\.

f = 1300 MHz Max. Gain = 34.4 dBir

I

Azimuth Angle ( Degrees)

5131183

Page 8

Chap 2 Par 16

5/31/83 6340.15

Chap 2 Par 16

Fig. 2-3 TYPICAL ARSR-3 AND MERF FREE- SPACE

ANTENNA ELEVATION PATTERN

ANTENNA ELEVATION PATTERN

tap) AOM au0 JoMOd r~!&o(a~

Page-9

6340.15 5/31/83

(4) Polarization,

(a) Definitions, The direction of polarization of an antenna is defined as the direction traced in a plane by the tip of the radiated electric field vector, Most radars are linearly polarized;-that is, the direction of the electric field vector is constant as a function of time. The polarization may also be elliptical or circular. Elliptical polarization may be considered as the combination of two linearly polarized waves of the same frequency, traveling in the same direction, which are perpendicular to each other in space. The relative amplitudes of the two waves and their phase relationship can assume any values. If the wave amplitudes are equal, and if they are 90 degrees out of (time) phase, the polarization is circular. Circular and linear polarizations are special cases of elliptical polarization. More details on polarization can be found in references 3 and 4.

(b) Performance Characteristics. Linear polarization normally produces greater signal return due to higher values for the product of antenna gain and target cross section in this polarization. Circular polarization is used at times, however, weather disturbances..

to reduce clutter produced by rain, fog, or other The impact of reduced radar range coverage during operation with circular polarization and of its effect on tangential course problems should be considered when establishing a radar site. In the absence of conclusive experimental data indicative of the degree of CP coverage reduction for a given aircraft, the detection range with circular polarization may be assumed to be approximately 75 percent of the range with linear polarization. This is based upon an interpolation of data from p. 147 of reference 2.

(c) ARSR Polarization. ARSR equipment is arranged to operate using vertical, horizontal, or circular polarization. The ARSR-3 has two radar channels-- each with its own transmitter and receiver, but with the antenna shared using two separate inputs to the antenna polarizer. The two channels always utilize radiation with orthogonal polarizations: when one channel uses vertical polarization, the other uses horizontal; and when the polarizer is switched to circular polarization, the two channels use radiation with the opposite sense circular polarization (right handed and left handed).

(5) Scan Rate. The rate at which the ARSR fan beam antenna rotates on its pedestal is called the scan rate. This rate is important to radar operation since it, together with prf and beamwidth, determines the number of radar pulses which will impinge upon a target during the passage of the search beam. The'number of pulses, in turn, affects target detectability. Scan rate is equivalent to the primary radar data refresh rate supplied to the traffic controller. The scan rate for the ARSR-3 is five rotations per minute.

Page 10

Chap 2 Par 16

S/31/83 6340.15

(6) Passive Horn.

(a) Purpose. The ARSR-3 has two similar antenna feedhorns, one mounted immediately above the other. The antenna patterns for the two feedhorns (plus the reflector) are almost identical except for a vertical displacement of approximately four degrees as shown in figure 2-4. The lower beam is used for transmission, and for reception in the detection of targets. at long range, where the elevation angle is small. The upper beam is used for reception in the detection of close-in targets where ground clutter returns are present. Due to its upward tilt, the high beam has a lower gain at the low angles where clutter returns arise, thus reducing the received clutter power and consequently improving the signal-to-clutter ratio.

(b) Performance. Use of the passive horn for signal reception can provide as much as 19 dB of signal-to-clutter improvement, thus enhancing the radar's capability for detecting close-in targets. Improvement for a typical case is indicated in figure 2-5, The overall radar coverage provided by the main and passive antennas are also shown in figure 2-6 for a typical

case. The figures indicate that while use of the passive antenna provides improved operation in clutter, this is achieved at the expense of free space coverage of longer range targets. For this reason, ARSR-3 operations should utilize the passive antenna only for target ranges where clutter is visible

to the main antenna. For longer range reception, operation should be switched to the main beam to improve detection capability.

(c) Beam Switching. After a radar pulse is transmitted on the low beam, radar returns are received simultaneously on both the low and high beams and their associated receivers. In each azimuthal sector signals from the high-beam receiver should be used for ranges out to the maximum clutter range along that azimuth, and the low-beam receiver output should be used for ranges beyond the maximum clutter range. As a typical example of an unscreened case, with an antenna height of 55 feet and Onegree antenna tilt angle (for the lower 3 dB point of the low beam), the optimum switching point would occur at approximately 9 nmi, assuming clutter out to the radar horizon,

Switching is controlled in 32 adjoining azimuth regions (each 11.25 degrees) by' the range/azimuth gate generator (rag). The available increments for range switching are 10 nmi for ranges between 10 and 100 nmi, and 20 nmi between 100 and 200 nmi.. Siting of the ARSR-3 should take into consideration the clutter reduction capabilities provided by use of the passive antenna beam.

(7) Antenna Height.

(a) Effect on Coverage. The height at which ARSR antenna is installed, defined by the horizontal center line of the main horn, is important to the overall radiation characteristics insofar as these are modified by the reflecting of the terrain surface. Pattern distortion and vertical lobing effects are natural by-products of over-ground installation and cannot be wholly avoided. These effects are dependent upon the height of the antenna installation. Radar screeningangle isalso important to overall ARSR operation, and this too is affected by the antenna height. The selection of an antenna

Chap 2 Par 16 Page 11

6340.15 5/31/83

Fig. 2-4 ARSR-3 ANTENNA DESIGN PATTERN

Fig. 2-4 ARSR-3 ANTENNA DESIGN PATTERN

I I

c.-” 9) I ’.- 2

a0

I I

1

E- 0: mm

c.- I”

8 E x !c 0 in--

(J!6P) u!OF) ouua~utf

Page 12

Chap 2 Par 16

20

I8

2

C

Fig. 2-5 SIGNAL - Td- CLUTTER IMPROVEMENT PRO-

VIDED BY USE OF ARSR-3 PASSIVE ANT- ENNA HORN

Notes :

I. Calculated Values Shown Assume Ideal Free-Space Conditions With Lower 3db Point Of Low Beam Set At O” Elevation (Antenna Tilt =OO)*

VIDED BY USE OF ARSR-3 PASSIVE ANT- ENNA HORN

2 improvement Shown Is Produced Primarily By Reduced Clutter Input When Upper Beam Is Used For Receiving.

E

I 5 IO I5 20 25 3 0 35 0” .u Target Elevation Angle (Degrees 1 in

FIGURE 2-6 FREE SPACE ARSR -3 COVERAGE OF T-33 AIRCRAFT UPPER BEAM VERSUS LOWER BEAM RECEPTION

#PUlATIONAL CONDITIONS

#PUlATIONAL CONDITIONS

Free Space Condltlons Including Atmospheric Attenuation Antenna Tilt Angle (Lower 3 dB Point of Hdfn Beam) = go

Target Cross Section - 2,.2 m2 (T-33)

Detection Probability = 0.8 False Alarm Probability= lo-'

Frequency = 1300 MHz IF Bandwidth = 500 *Hz

PRF = 340 HZ Oiplex Operation (Ref. to Table 2.1 for Sther Parameters)

Range 1 Nautical Miles )

S/31/83 6340.15

height involves a trade-off in coverage requirements. The tower should be as high as necessary to achieve the required low altitude target coverage, but should be kept low to minimize waveguide losses and to take advantage of close in screening objects.

(b) Available ARSR-3 Heights. The antenna heights available for a given installation are constrained somewhat due to the nature of standard FAA radar towers. Available tower heights are 25, 37%, 50, 62%, or 75 feet. The antenna main feedhorn is an additional 12 feet above the top of the tower. Consequently, the resultant height will be 37, 4931, 62, 74% or 87 feet above the local surface of the ground,

(8) Antenna Tilt Angle.

(a) Purpose of Tilting. The antenna tilt angle determines the angular relationship of the elevation pattern with respect to the horizontal. This is adjusted after installation for optimum radar performance. Consideration should be given to tilt angle at the time of siting, however, since it affects the amount of clutter received by the ARSR, the range coverage pattern, and the depth of nulls in vertical lobing patterns of both ARSR and ATCBI equipment. Ordinarily, antenna tilt is set at the best compromise value between (a) the low angles required for best long range coverage of low alti-

tude fixes, and (b) the high angles required for minimizing clutter input such that good near-in radar detection is possible. For many installations this occurs when the antenna's lower half-power point is at an elevation of about 0.25' degrees. This rule-of-thumb may be altered in the case of ARSR-3 installations where the passive horn may allow use of lower tilt angles than would otherwise be possible, due to the signal-to-clutter improvement noted above. Two types of antenna tilting are possible with the ARSR-3 as discussed below.

(b) Tilting Antenna on Pedestal. The antenna reflector can be tilted with respect to the antenna pedestal, This feature allows the beams to be tilted within a six degree interval. The tilt is continuously adjustable so that the underside -3 dB point of the low beam can be set to any angle between -3 degrees and +3 degrees above the horizontal. The underside -3,dB point on the low beam elevation pattern is the tilt reference point. This tilt mechanism provides the same beam tilt angle at all azimuths as the antenna rotates.

(c) Tilting of Pedestal. The mounting pedestal, which supports the reflector, polarizers, and feedhorns is capable of operatingin anunleveled position sufficient to tilt the antenna beam 2 2 degrees in elevation with re-

spect to the horizontal when the antenna is directed at any specified azimutt. The pedestal can be tilted in O.l-degree vertical increments over the full - 2 degree range. By tilting the antenna pedestal some amount, for example,1 degree above normal $n any direction, the antenna will mechanically scan sinusoidally in elevation - 1 degree as the antenna rotates through its 360-degree scan. For some radar sites this type of capability could provide improved low angle

coverage over clutter which is concentrated in one azimuthal sector.

0 Chap 2 Par 16 Page 15

0 Chap 2 Par 16 Page 15

6340.15 S/31/83

(9) Radome. All ARSR-3 installations employ a radome to protect the antenna from severe weather conditions. The radome attenuates the radar signals by 0.6 dB in each direction. These losses have been includedintheradar coveragecharts includedinthishandbook. TheMERF antennadoes notuse aradome.

b. Signal Characteristics.

(1) Frequency. The rf operating frequency of the ARSR-3 and the MERF is adjustable within the band 1250 MRz to 1350 MHz. While the MERF is a

single channel radar, the ARSR-3 is a dual-channel frequency diversity radar, having duplicate transmitter and receiver systems with the tvo channels operating at different frequencies. Simultaneous operation at two frequencies separated by at least 25 MHz (avoiding transmit frequencies separated by the STALO frequency 31.07 MHz, i.e., channei numbers n and n-+12) and using orthogonal polarizations substantially improves the probability of detecting a slowly scintillating target. Selection of the operating frequencies for a given ARSR installation should be made at the time of siting based on interference considerations. This can be done by collecting information on the operating frequencies of all nearby radar and/or communications equipment and selecting a compatible ARSR operating frequency. Selection should consider the harmonic content of signals as well as their fundamental frequencies. ARSP. frequency selection is made by r.egional Frequency Management Division personzei. iieference 15 provides infomnti on ust?ful in determining compatible operating frequencies.forARSR siting.

(2) Pulse Duration. The duration of the transmitted pulse establishes the range resolution capability of the radar, the range dimension of each illuminated ground clutter patch, the required receiver bandwidth, and the minimum range of the radar. Pulse duration is fixed at 2 microseconds for the ARSR-3 and MERF radars, as indicated in table 2-1.

(3) Pulse Repetition Frequency (PRF).

(aj Unambiguous Radar Range. The number of radar pulses transmitted per second is known as the pulse repetition frequency. PRF determines the maximum unamoiguous range of the radar, beyond which second-time-around echoes can appear as close-in targets. The regions of normal returns and of second-time-around echoes are shown In figure 2-7. Surveillance radars are designed with prf's which ordinarily avoid the occurrenceof rangeambiguities within the area of desired coverage. However, conditions of anomalous propagation or an exceptionally strong source of reflection at a very distant loca-

tlon may produce an ambiguous return.

(b) Target Detectability in Receiver Noise.

1 Fonnulation. The prf affects target detectability in several ways. First, the prf, along with the antenna's azimuth beamwidth and angular scan rate, determines the number of pulses, N, impinging on the target and integrated during each antenna scan. This number is important in determining the detectability of a weak target in the presence of receiver noise; it is found from the following relationship:

Page 16

Chap 2 Par 16

S/31/83 6340.15

Fig. 2-7 RANGE AMBIGUITY POINTS

Fig. 2-7 RANGE AMBIGUITY POINTS

600

500

400

300

200

100

0

,2nd Range Am bigulty

-

Sec6nd-Time-Around Region.\

I st Range Ambiguity

Region Of Normal Return

Chap 2 Par 16

300 320 340 360

Radar PRF (Hz)

300 400

Page 17

6340.15 5131183

eafr M==

r

where

8 = antenna azimuth a

fr = radar prf (Hz)

(2-l)

beamwidth (degrees)

Wr = scan rate (rpm).

2 Application. This equation applies directly to the MEPF, which has one rahar channel. However, for the ARSR-3, which has dual channel capability, M is twice as large when both channels are used. In both the ARSR-3 and the MERF, 8, = 1.10, and w, = 5 rpm. Figure 2-8 shows the varia-

tion of M, as operation.

In order that

a function of prf, for both single-channel and dual-channel

(c) PRF Effects on Moving Target Indicator (mti) Performance. the mti system provide good clutter suppression as well as good target detectability at all radial velocities, staggered prf's are used. Incremental adjustment of the prf allows an average prf between 310 and 364.5. Any one of three prf stagger programs can be selected, depending on the average prf desired. If second-time-around clutter returns are received and are to be cancelled, the transmission must be changed to a fixed interpulse period instead of the usual variable interpulse period. This feature can be programmed for one sector using the range-azimuth generator (rag).

(d) Interference/PRF Assignment. With suitable rf frequency assignment, it is unlikely that interference will occur between the ARSR and another radar, especially if the ARSR is geographically separated from the other radar by a substantial distance, for example, several tens of miles. However, if interference does occur, it is possible that adjustment of the prf can reduce or eliminate any operational difficulty. FAA frequency management personnel are responsible for the final prf assignment as well as for

the rf frequency assignment. See reference 15.

C . Receiver Characteristics. Only a small portionof theenergy radiated from the antenna strikes a distant target in spite of the beam shaping produced by a narrow beam antenna. The target reflections are, in turn, widely scattered, producing a received echo signal which is very small. The radar receiver, therefore, must be capable of detecting and amplifying these weak signals despite competing noise and clutter inputs.

(1) Sensitivity. The effective range of a surveillance radar for a given size target, in most cases, is directly dependent upon the sensitivity of its receiver; that is, the ability of the receiver to detect and utilize weak echo pulses. Generally, the weaker the signal which can be detected the greater the effective range of the radar. The fundamental limitation on weak

Page 18

Chap 2 Par 16

5/31/83 6340.15

Fig. 2-8 HITS/SCAN VS PRF FOR ARSR-3

Fig. 2-8 HITS/SCAN VS PRF FOR ARSR-3

EQUIPMENT

30

25

20

I5

IO

S

0

.

.

I

300

Dual -Channel Operotion

Single - Channel Opera!ion

320 340 360 380 400 Radar PRF,fr (Hz)

Chap 2 Par 16 Page 19

6340.15 5/31/R3

signal detection is the noise generated in the receiver input circuits. To achieve a satisfactory probability of detection along with an acceptable false alarm rate, the received signal, after processing in the receiver, must be of sufficiently greater amplitude than the inherent receiver noise. Where ground clutter effects are observed, effective surveillance range is dependent upon the ability of the receiver and processor to raise the ratio of input signal to clutter-plus-noise to a level sufficient for detection.

(2) Sensitivity Time Control.

(a) Purpose. Sensitivity Time Control (stc) is incorporated into ARSR systems to reduce the risk of receiver saturation due to clutter returns, which can be especially strong at short range. If the receiver is saturated by clutter, it will not respond to the additional signal input from a target, and thus signal detectability is impaired. In order to reduce the likelihood of receiver saturation on these clutter returns, receiver gain is intentionally reduced at short range, and gradually increased up to its maximum value at some greater range where clutter is not likely to cause satura-

tion. The reduced sensitivity at short range may also reduce the visibility of certain second-time-around echoes from strong, very distant reflectors and undesired moving targets such as birds and automobiles.

(b) STC Implementation. A digitally generated stc controlwaveform is used for controlling a PIN diode attenuator ahead of the receiver's rf amplifier. Four individually programmable stc waveforms are available, two for the upper beam and two for the lower beam. For each beam, the range/ azimuth gate generator (rag) can be used for selecting which of the stc wave-

forms is used-- one with strong stc action in azimuth sectors with high levels of clutter, or one with less stc in sectors with little or no clutter.

(3) Logarithmic Receiver Channel. A surveillance radar, especially one which is utilized in an automated ate system, should have a known, constant false alarm rate in order to avoid frequently overloading the tracking channel with spurious detections. Furthermore, the receiver must be capable of handling incoming signals over a wide dynamic range without limiting or saturating. Otherwise, a target signal, received simultaneously with strong clutter, will not be detected. To provide the required performance, the receiver is designed to have a logarithmic characteristic with over 60 dB dynamic range. As an additional feature to reduce the chance of experiencing false alarms on the leading edges of clutter, the ARSR-3 receiver employs a special output filter. The receiver provides a virtually constant falsealarm rate (CFAR), and is termed a log-CFAR receiver.

(4) MT1 Capability.

(a) Purpose. To improve the ability of a radar to reject ground clutter, a (mti) moving target indicator receiver is often employed. With such a system, clutter rejection is achieved by signal processing techniques which distinguish between moving and stationary targets. In many older surveillance radars this was done through the use of delay-line feedback networks

Page 20

Chap 2

Par 16

5131183 6340.15

which provide destructive cancellation of the video return signals whose phase and amplitude are unchanged from pulse to pulse. The phase of the signal produced by a moving target is not constant from pulse to pulse and so yields an uncancelled residue which can be detected. In new ARSR equipments, such as the ARSR-3, the video signal is sampled, and the samples are stored as digital numbers. Consequently, in a digital mti of this type the signals can be stored, delayed, weighted, and added with the convenience, accuracy, and stability associated with digital computation.

(b) ARSR-3 Techniques. The ARSR-3 employs several techniques to yield improved mti performance relative to earlier radars. It uses two detector channels,anin-phase channel(I), and a go-degree or quadrature channel (Q), to avoid the blind-phase problem which can be encountered in receivers using only one synchronous detector. The ARSR-3 uses a three-pulse canceller with staggered prf to provide a relatively smooth nlti velocity response with no blind speeds to over 2000 knots. Also, the range/azimuth generator (rag) provides thirty windows where either mti video or log video can be used. MT1 should be used to improve aircraft detection only wherethere isground clutter. To avoid possible signal losses, such as those from aircraft on tangential courses, do not use mti when not needed for reduction of ground clutter, Although the ARSR-3 incorporates numerous features to control false alarms, extreme,ground clutter at some locations may not be completely cancelled. To help prevent alarms in such cases, a Dynamic Threshold Generator is incorporated in the radar. It senses and stores information on clutter amplitude prior to'the mti canceller. When the clutter amplitude exceeds the,cancellation capability of the mti, the video quantizer threshold is raised by a small amount. The dynamicthreshold isapplied onlyto themti sectorsunder ragcontrol.

(c) Performance. The most important figure of merit for an mti system is the improvement factor,defined asthe ratioof signal-to-clutter out of the canceller to signal-to-clutter into the canceller. For the ARSR-3, which uses a 3-pulse canceller, the mti improvement factor is 39 dB. As will be shown in chapter 3, signal detectability in the presence of clutter can be determined using this value for the signal-to-clutter improvement due to receiver processing, in conjunction with estimates of received signal power, received clutter power, and signal-to-clutter improvement provided by use of the ARSR-3 passive antenna horn (figure 2-5). Another important aspect of mti performance is the behavior at various radial velocities. Figure 2-9 shows the signal response for the ARSR-3 mti channel relative to the response using the ARSR-3 normal receiver (log CFAR). There are no blind velocities

to over 2000 knots. At 75 knots radial velocity, relative response is down by approximately 8 dB. It then increases, and it is at least equal to response of the normal receiver down to the radial velocities of 20 knots.

(5) Pulse Integration. Pulse integration is employedin surveillance radars for the purpose of enhancing signal detectability. For the ARSR-3,each of the two displaced transmitters illuminates the target approximately 12.5

times as the beam scans past the target. Thus, for dual-channel operation, 25-pulse echoes are received. Pulse integration is the process of adding together the target returns from these successive pulses, thus yielding a

Chap 2 Par 16 Page 21

IO

0

-10

-20

-30

/’

0.2 0.5

l-J.8 dB

I

I 2 5 IO

Dopplk Frequency

20 , PRF

IO 20 50 100 200 500 1000 2000Knots

Range Rote

S/31/83 6340.15

-

higher net signal-to-noise ratio, and consequently a higher probability of detection (Pd) for a given false alarm rate. Alternatively, for a specified required value of Pd, integration allows the use of a lower input signal-tonoise ratio, and thereby increases the range to which a target is detectable. The two'radar channels operate at an rf frequency separation of at least 25 MHz so that the signal fading in the two channels is uncorrelated. The statistics of the signal fading tend to follow the theoretical model of the Swerling Class III target. The effective signal-to-noise improvement due to integration depends on the probability of false alarm (Pf ), the probability of detection (Pd), and the number of pulses integrated (My. For Pfa = 10-6,

'd = 0.8, and M = 25, this integration gain is approximately 9.9 dB. Pulse

integration is employed in both the normal receiver and the mti receiver.

(6) Range/Azimuth Gating (rag). New ARSR equipment such as the ARSR-3 will contain a range/azimuth gate generator which will generate a variety of programmable azimuth/range windows, azimuth gates, and rangegates.

Some of these are outlined briefly below. The added radar capability which is provided by the rag should be considered at the time of siting, since it may allow an increase in the number of potentially acceptable site locations.

(a) Video Gating. The rag provides for selection of one or two video signals on range/azimuth basis. This will normally be used for gating between mti and normal video. The rag will have the capability of generating 20 range/azimuth gating windows, beginning at zero range and adjoining in azimuth. Ten additional adjustable, isolated gating windows will also be provided for this purpose.

(b) Antenna Beam Switching. As discussed above, the rag also allows switching from high to low beam antenna at selectable range in eight contiguous azimuth regions beginning at zero range, and at four additional isolated range/azimuth windows.

(c) PRF Stagger Operation. The rag provides the capability for switching from prf stagger to nonstagger operation on an azimuth basis.

(d) Receiver Gain. The rag has eight isolated windows for receiver gain control, plus provision for selectionof eitherof twostc curves.

(7) Digital Target Extractor. its design,

The ARSR-3, as an integral part of incorporates a digital target extractor (dte) which converts the hit-by-hit wideband radar pulses and the received beacon signal into digital target centroid data along with aircraft identity and altitude information at the radar site. The radar and beacon data can thw be remoted to the Air Route Traffic Control Center over narrowband links such as telephone lines, instead of via a wideband transmission system such'as a microwave link.

(8) Moving Target Detector (MTD). Improvements are constantly being made to provide better signal detectability in the presence of clutter. The moving target detector (mtd) is presently in development and will subsequently be used in the ARSR-4 and other new air traffic control radars. It will

Chap 2 Par 16 Page 23

6340.15 5131183

process digitized receiver output signals to detect moving targets, while rejecting fixed ground clutter, precipitation clutter, and pulsed interference. It will incorporate numerous sub-units including a two-pulse canceller,digital filters, clutter map, various thresholders, and a weather processor. The mti improvement factor will be approximately 48 dB (within 2 dB of that obtainable with an optimum processor). The digital processing systems incorporated into this unit will develop reconstituted video for display on standard FAA PPI displays.

17.-19. RESEWED.

Page 24

Chap 2 Par 16

S/31/83

SECTION 3. AIR TRAFFIC CONTROL RADAR BEACON SYSTEM

SECTION 3. AIR TRAFFIC CONTROL RADAR BEACON SYSTEM

20. FUNCTION.

a. Purpose. The Air Traffic Control Radar Beacon System (ATCRBS) is designedto providean enhancedradar detection,location, andidentification capabilityfor controlof properly equipped aircraft. The systemis employed at both terminal and enroute FAA radar sites and is of extreme importance to the efficient control of aircraft, especially during poor weather conditions.

b. System Components. With ATCRBS, detection of aircraft is dependent upon reception of reply signals from an airborne transponder device, a process normally much more reliable than conventional radar surveillance. The basic ATCRBS components include an interrogator, a transponder and an indicator. The Air Traffic Control Beacon Interrogator (ATCBI) transmitter/antenna radiates short coded~pulses at a fixed frequency of 1030 MHz. This signal, when received and validated by,an antenna/transponder unit aboard an aircraft,

initiates generation of a reply pulse train at 1090 MHz.

c. Target Detection and Display. Detection occurs when the transponder reply signal is picked up by the interrogating antenna, processed, and displayed on an ARTCC indicator. Target bearing and range are determined from the antenna point angle and signal propagation time, as for a skin-track radar. The range determination takes into account the time delay introduced by the airborne transponder unit. ATCRBS and ARSR transmissions are synchronized such that the video output from each can be displayed, in proper alignment, on the same indicator. Additional information can be provided by the beacon system since the reply pulse train format is independent of the interrogation signal. The reply signal is usually coded to provide the controller with aircraft altitude and/or identification information.

d. Beacon System Designations. The Air Traffic Control Radar Beacon System (ATCRBS) has been designated as the secondary ra&z.r to distinguish its function from other FAA radar equipment. As more and more aircraft become beacon equipped, however, this designation is likely to be altered as the high density commercial terminals, ATCRBS is already the dominant factor in control operations. As such, ATCRBS should receive commensurate attention at the time of site selection. The beacon system currently being installed with the ARSR-3 surveillance radar is the ATCBI-5.

e. Future Beacon System. The FAA is developing a new aircraft surveillance and data-link system, the Discrete Address Beacon System (DABS). DABS will permit evolutionary upgrading of the civil and military air traffic con-

trol system. The central feature of DABS is the use of a discrete address code for each aircraft. Thus, each reply is identified with the proper aircraft. The discrete address function also provides a highly flexible data link supporting a wide range of advanced ATC automation services.

Chap 2 Par 20 Page 25

6340.15 S/31/83

21. EQUIPMENT PARAMETERS. The important parameters and functions cf the ATCBI-5 equipment presently being sited with the ARSR-3 at FAA en route facilities are tabulated in table 2-2.

22. AREA COVERAGE. The ATCRBS is capable of detecting aircraft within its line-of-sight at very long range. This is due to the high power capability of the equipment and the fact that propagation losses vary as Re2 for each of the one-way beacon paths, rather than the RB4 variation experienced by the primary radar. The maximum range of the beacon system is governed by the range of the interrogation link or the range of the reply link, whichever is less. The range of the reply link is fixed and is far in excessof thenominal maximum 200-mile detection range for an ARSR facility. The range of the interrogation link can also far exceed 200 nmi if the interrogator transmitter operates at full power. However, if desired, the interrogator power output can be reduced so that the interrogation link has only the range required for the beacon coverage needed. Thus the ATCRBS coverage range will ordinarily be determined by the interrogation link. Equipment should normallybe operated at the lowest output power which will permit reliable coverage of the required airspace volume. This practice will tend to minimize local interference and overinterrogation of aircraft transponders, and will reduce the fruit produced in other ATCRBS facilities. Figure 2-10 shows the ATCRBS range coverage characteristics; these are discussed more fully in chapter 3. Since separate transmitting and reply frequencies are used, g:rJund clutter and weather clutter do not introduce any limitations on coverage.

23. CHARACTERISTICS PERTINENT TO SITE SELECTION.

a. Antenna Coverage. The ATCBI system has two antennas: the directional main antenna and an omnidirectional antenna. The purpose of the main antenna is to efficiently radiate the interrogation pulse energy in a directional beam and to receive the transponder reply signals, sending them on to the ATCBI receiver for processing. The main ATCBI antenna consists of the ARSR-3 reflector illuminated by a separate beacon feedhorn adjacent to the radar feedhorns. An 8-foot-long vertical omnidirectional transmitting antenna, used as part of a sidelobe suppression system (sls), is mounted above the ARSR-3 reflector. The characteristics of these two beacon system antennas are described below.

(1) Directional Antenna,

(a) Antenna Pattern. The radiation pattern of the directional antenna is a fan beam narrow in azimuth and broad in elevation as shown in figures 2-11 and 2-12, respectively. The beam scans its coverage volume as the antenna is rotated at the 5 rpm rate of the.ARSR system. Figure 2-11 shows a portion of the azimuth pattern taken at O-degree elevation relative to the maximum in the elevation pattern. The strongest sidelobe is approximately 26 dB below the main lobe. Azimuthal patterns for higher elevation angles, e.g., 3 degrees, 10 degrees, 20 degrees, and 30 degrees (not shown) indicate simi'lar levels of sidelobes relative to the mainlobe radiation at those elevation angles. The physical horizontal offset of the radar and beacon feeds results in a 4-degree azimuth beam displacement, which is compensated for in the radar's digital target extractor (dte). Since the

Page 26

Chap 2 Par 21

S/31/83 6340.15

Table 2-2

ATCBI-5 PARAMETERS AND FEATURES

ATCBI-5 PARAMETERS AND FEATURES

Antenna

Directional

Pattern Shape Fan Beam Beamwidth

Azimuth 2.00 Elevation 90 Gain dbir 31 Polarization Vertical

Omnidirectional

Gain dbir 421

Interrogator

Transmitter

RF Frequency MHz RP Pulsewidth ~.ls Peak Power Output RF Pulse Pair

Spacing

Mode 1 W 2 W 3/A w B W C P D IJ PRF :I Mode Interlace

SLS Transmission Improved SLS

1030 + 0.2 0.8 + 0.1 SO-3165 watts

3 + 0.1 5 T 0.1 8 + 0.1 17 T 0.1 21 T-o.1 25 5 0.1

310- 365

X

X

X

Receiver

RF Frequency MHz 1090 f 0.2 Noise Figure 9-dB Tangential

Sensitivity -87 dBmmin STC lo-50 dB Defruiting - Digital Defruiter Mx- 8757 supplied

Remoting Cable

Maximum Length,ft 12,000 RG-llA/Uor RG-13A/U Maximum Length, ft 20,000 RG-35A/U

21 Synchronized with ARSR-3; Variable Interpulse Period (VIP) extends PRP Range - ATCBI-5 STC recovery time must be considered for some VIP modes. l

Chap 2 Par 21 Page 27

z

%

iii Figure 2- IO ATCRBS MAXIMUM RANGE COVERAGE (ATCBI - 5 )

-

-

-

6 0

- -

_- -

/ / / / / / / 7 -./ /

I I 8 0

7

2 Rdm E

2 Rdm E

PdCiGth-

(4r)zs,ninLt

-

+

I

4

I -

4

.- 2 -L-l--iJ.-.Jl-

Rdm = maximum interrogation range

‘d = ATCBI output peak power (meas. at antenna)

s = min transponder minimum sensitivity

ci = interrogator antenna gain (assumed Gi = 31 DBIR)

Gt = transponder antenna gain

Lt = transponder RF losses

N o t e : Computation assumes G, 3 L,

100 120 140 160 I80 200 220 240 2 6 0 260

Maximum Range (Nautical Miles)

50 -

.----

-

4 0

S/31/83 6340.15

Fig. 2-11 TYPICAL FREE-SPACE AZIMUTH PATTERN

Fig. 2-11 TYPICAL FREE-SPACE AZIMUTH PATTERN

FOR ATCBI DIRECTIONAL ANTENNA WITH PRSR-3 REFLECTOR

h m0

al>.- ‘05p:

0

4

I I I

Gain = 31 dBir

f = 1030 MHz 0

12 II I I I I I I I I I I I

16

24

28

32

36

40

44

48

52

56

60 72 48 24 0 24 48 72

Azimuth Angie (Degrees)

Page 29

6340.15 5131183

Fig. 2 -I 2 TYPICAL FREE-SPACE ELEVATION

Fig. 2 -I 2 TYPICAL FREE-SPACE ELEVATION

PATTERN FOR ATC81 DIRECTIONAL ANTENNA WITH ARSR-3 REFLECTOR

0”3

a? 6

Q)> .-c

0 5a

0

4

8

12

16

20

24

28

32

36

40

44

48

52

56

60 72 72 48 48 uQ 24 24 0 24 24 Above Above

+-I-- +-I--

Below Below “En?’ “En?’ NO,SeeBmOf NO,SeeBmOf

f = 1030 MHz

PATTERN FOR ATC81 DIRECTIONAL ANTENNA WITH ARSR-3 REFLECTOR

Elevation Angle (Degrees 1

Page 30

5131183 6340.15

beacon feedhorn is separate from the radar feedhorn, it can be independently

tilted to optimize usage of its sharp beam underside cutoff in controlling ground illumination and vertical lobing.

(b) Antenna Cain. As mentioned above, the gain of an antenna is a quantitative measure of the directivity compared with a reference standard (usually an isotropic radiator). Its maximum value is used as a measure of antenna performance. As noted in table 2-2, the maximum gain for the ATCBI main antenna, as part of the ARSR-3 system is 31 dBir.

(c) Beamwidth. Since ATCBI equipment must perform a function similar to that of the primary radar, antenna beamwidth requirements are also similar. The 3 dB azimuth ATCBI beamwidth is narrow (2.0 degrees) to provide good target resolution, and elevation beamwidth is broader (approximately 9 degrees) for good vertical coverage of the surveillance volume, Target altitude information is not derived from the beacon antenna elevation pattern, but directly from coded data in the beacon reply signal.

(d) Polarization. ATCRBS equipment, because of the requirement for cooperative operation of both ground and airborne equipment, operates only with vertical polarization.

(e) Scan Rate. Because the same reflector is used for both the ARSR-3 antenna and the ATCBI main antenna, the scan rate of the beacon system is the same as that of the radar, 5 rpm.

(2) Omnidirectional Antenna. In all ATCBI installations a supplementary, fixed omnidirectional antenna is employed in conjunction with the use of a Sidelobe Suppression (~1s) system. SLS, which is described below, utilizes the omnidirectional antenna to suppress interrogation of properly equipped aircraft transponders via sidelobe transmission paths. In addition, use of improved sls suppresses interrogation of properly equipped aircraft transponders via reflections from nearby objects. The elevation pattern of this antenna is given in figure 2-13. The omni antenna has a sharp cutoff on the underside of its vertical pattern to minimize differences between the vertical lobing patterns of the main beacon antenna and the omni antenna. The vertical displacement of the directional and omni antennas will result in some mismatch of the lobing patterns. Maximum gain of the omni antenna antenna is vertically polarized.

(3) Five-Foot Planar Array. The antenna system en route DABS, when it is incorporated, is the five-foot, gain array, A typical elevation pattern for this antenna 2-14 and an azimuth pattern in figure 2-15.

b* Signal-Characteristics.

is 5.5 dBir. The

to be used with the light weight-high is shown in figure

(1) Introduction. The ATCRBS signal characteristics can most conveniently be discussed in terms of the basic interrogation signal, the reply signal, and the added features of the interrogation signal which act to'suppress the unwanted interrogations caused by sidelobes of the interrogator/main antenna. These signal characteristics are discussed below. Chap 2 Par 23 Page 31

6340.15 5/31/83

Fig. 2-13 TYPICAL VERTICAL PATTERN OF ATCBI CM~~DI~ECTIONAL ANTENNA USED WITH

Fig. 2-13 TYPICAL VERTICAL PATTERN OF ATCBI CM~~DI~ECTIONAL ANTENNA USED WITH

Page 32

Chap 2 Par 23

5/31/83 6340.15

FIGURE 2-14 TYPICAL FREE SPACE ELEVATION

RADIATION PATTERN FOR FIVE- FOOT

LIGHT-WEIGHT HIGH GAIN ARRAY TO BE USED WITH EN ROUTE DABS

-8

POP - 12 Y

9”3 - I6 al 0’ -20 iii3 B -24

LIGHT-WEIGHT HIGH GAIN ARRAY TO BE USED WITH EN ROUTE DABS

aI> .-- -28

0

a -32

-36

+72 +48 +24 O0 -24 -48 -72

A n-g 1-e

Page 33

Page FIGURE 2-15 TYPICAL FREE SPACE AZIMUTH RADIATION PATTERN FOR FIVE -FOOT LIGHT-WEIGHT HIGH GAIN ARRAY TO BE USED WITH EN ROUTE DABS 6340.15 0

4

(80) -12

-16 auo -20 Power -24

Relive -28 -32

-36

-40 Par 23 Chap 2 -108° -72° -36° Azimuth Angle 0° +36° +72° +108° 5/31/83

5/31/83 6340.15

(2) Basic Interrogation Signal.

(a) Modes. ATCBI-5 interrogators transmit a sequential series of three 0.8-US pulses at 1030 MHz as shown in figure 2-16. The first and

third pulses, Pl and P3, are radiated via the ATCBI directional antenna and are the basic interrogation signal. The spacing between Pl and P3 establishes the interrogation mode as shown. (P2 is radiated via theomniantennafor sidelobe suppression 2.0 ~.ls after Pl is radiated from the directional antenna). Six possible modes (designated mode 1, mode 2, mode 3/A, mode B, mode C, and mode D), may be used, but usually only modes 3/A (common identity)and C (common altitude) are used in air traffic control. It is common to interlace these two modes on a 1:l or 2:l basis to update identity and altitude data on each scan of the ground based antenna. The interrogation mode sequences available with the ATCBI-5 interrogators, some interlaced and some not, are given below. The X,Y, andZ correspond to any of the ATCRBS mode designations (i.e., mode 1, 2, 3/A, B, C, D).

… (no interlace) … (no interlace) zzzzz … (no interlace)

… XXYXXY … XYZXYZ … XYXZXYXZ …

… XXYXXY … XYZXYZ … XYXZXYXZ …

(b) Interrogation Repetition Frequency, The rate at which the interrogation pulse program is transmitted is termed its prf. This rate is normally adjustable between 150 and 450 Hz. The adjustment is important to equipment installation insofar as it must be kept different from other ATCBI equipment in the vicinity. Selection of a unique prf for beacon operation enhances the capability of its video defruiting equipment, thereby resulting in improved ATCBI performance. In joint ARSR/ATCBI installations, the ATCBI prf is derived directly from the basic prf of the ARSR equipment. Because of

this interdependence, and the interference implications to operation of both systems, prf selection is usually the responsibility of FAA Regional Frequency Management personnel.

(3) Reply Signal. For each interrogation, the elicited transponder reply (at 1090 MHz) comprises up to 16 pulses spaced at multiples of 1.45 ps as shown in figure 2-17 and table 2-3. Two of the pulses, Fl and F2, are always present to define the pulse train. The other pulses contain the coded data (usually identity or altitude) requested by the interrogator mode selec-

tion. The specific aircraft identity code used is assigned by the airtraffic controller through voice communications, Also, one of the reply pulses can be used for special identification if the same identity code has been redundantly assigned to two or more aircraft within the surv&llance volume. Special reply code provisions enable the pilot to declare an emergency or a communications failure. Some example pulse trains are illustrated in figure 2-17.

l

Chap 2 Par 23 Page 35

6340.15 5/31/83

Figure 2- 16. INTERROGATION PULSE SPACINGS

FOR ATCBI MODES

FOR ATCBI MODES

3L-l.

2

Mode I

Mode 2 ,

Mode 3/A

17

Mode B

ml

-

c

4 21 m

I ) - -

Mode C - -

* 25 m

PI P2

Mode D

P3

Notes : (I) All Times In Microseconds

(2) All Pulses 0.8 Microsecond Wide (3) PI 8 P3 Are Radiated By Directional Antenna ; P2 Is Radiated By Omni Antenna

Page 36.

Chap 2 Par 23

5/31/83 6340.15

Figure 2-m EXAMPLES OF PULSE CODES

ATCRBS REPLY

ATCRBS REPLY

C O D E 7 7 7 7 W I T H X A N D IDENT

FI C l A l C 2 A 2 C 4 A 4 X 81 DI 82 0 2 0404 F 2 IDENT

C O D E 6 2 4 - 7

FI ~2C4 A 4 01 82 0 2 04 Ft

T I N E , U S --.- m

(a) TWO OF THE POSSIBLE 4096 REPLY CODES

USING A, B, C, AXD D PULSE POSITION

C O D E A 7 0 7 k. . . __- e--e - 2 4 6 I) - _-_ _.

USING A, B, C, AXD D PULSE POSITION

I r .-.-. __ -.--. . -.- 20 3 ---. -4

‘b _.. -__.- . - r7 4 - --

c, _.-_- _ .-- ,4 g --... - -

I4 --- II 6

FI A A

-I

b e 0 0 F2 I DENT

T I M E , U S

(b) COWON SYSTM REPLY CODE TRAIN

CONTAINING ALL PULSES IN A AND B PULSE POSITIONS AND AN INCIDENT PULSE

C O D E 6 3

FI AI A2 A4 01 82 84 F2

FI AI A2 A4 01 82 84 F2

CODE S2

FI AI A2 A4 81 02 64 Ft

C O D E 3 4

FI AI A2 h.4 81 82 84 Ft

TlYE , U S - -_ ___-*

(c) THREE OF THE POSSIBLE 64 COMMON

SYSTEM REPLY CODE USING A AND B PULSE POSITIONS

Chap 2 Par 23 Page 37

Table 2-3

ATCRBS TRANSPONDER REPLY CODES

S/31/83

l Two Framing Pulses (Fl, F2) … 0.45 + 0.10 lls 13 possible information pulses between framing pulses Fl, F2.

ATCRBS TRANSPONDER REPLY CODES

IDENT pulse spaced 4.35 us after F2.

l Reply Pulse Train

Pulse Width … 0.45 + 0.10 L!S Pulse Spacing … 1.45 us Pulse Cl … 1.45 jls Pulse Al … 2.90 ps Pulse C2 … 4.35 J&s Pulse A2 … 5.80 us Pulse C4 … 7.25 us Pulse A4 … 8.70 us Pulse X … 10.15 ps Pulse Bl … 11.60 3s Pulse Dl … 13.05 'cis Pulse B2 … 14.5 0 us Pulse D2 … 15.9 5 ps Pulse B4 … l7.4 0 us Pulse D4 … 18.85 us

Page 38

Chap 2 Par 23 0

S/31/83

(4) Side-Lobe Suppression (SLS).

.(a) Purpose, This feature is incorporated into ATCBI equipment to reduce interrogationof aircraft transponders via side-lobe radiation (nominally 24 dB below the peak of the beam) of the directional beacon antenna. Depending on the power transmitted, side-lobe ATCBI radiation can trigger replies at considerable distances from the radar , giving rise to a PPI effect known as ring-around (figure 2-18) with great deterioration of azimuth accuracy and resolution, and increased interference. Side lobe suppression techniques are incorporated into the system to allow aircraft transponders to distinguish between main and sidelobe interrogator radiation.

(b) Description. With the sls feature, normal directional radiation of Pl and P3 pulses is augmented by radiation of a control pulse, P2, from the!ATCBI omnidirectional antenna. The P2 pulse, which always fol-

lows the Pl pulse by 2 ps, is compared in amplitude with Pl in transponders equipped with sls circuitry. The pulse amplitude comparison is implemented by a desensitization technique. Upon receipt of a pulse with more than 0.7 ~J.S duration, the transponder receiver is desensitized to a level which is within 9 dB of (but not exceeding) the amplitude of the desensitizing pulse. Recovery is approximately linear over a 15 j.ls interval. When the Pl pulse amplitude is 9 dB (or more) greater than the P2 pulse amplitude, indicative of main beam interrogation,the P2 pulse is not detecteddue to desensitization,

and a transponder reply is generated after reception of the P3 pulse, If the Pl and P2 pulse amplitudes are equal, clearly indicating a side-lobe transmission path, the P2 pulse is 'detected despite receiver desensitization and the transponder's reply capability is suppressed for aperiod of35+10 vs. Figure 2-19 indicates the pulse timing and amplitude relationships of the sls system.

(c) Effect of Multipath. Whereas ring-around is effectively controlled by side-lobe suppression, the technique is not as effective in removing the effects of reflections or multipath. Under this condition, false targets are generated when main beam energy from the ATCBI directional antenna successfully interrogates a transponder via a reflected signal path. When this occurs, in addition to the proper target display, a false target is displayed at the azimuth of the reflected path and at a range corresponding to the path length, including the reflection segment of the path. This is illustrated in

figure 2-20.

(d) Examples of Multipath. Under the condition where the direct path sls P2 pulse and directional antenna side-lobe Pl and P3 pulses are received by the transponder, a 35 + 10 us suppression gate is generated which prevents some reflected path interrogations. This isillustrated in figure 2-21. Several conditions can occur, however, in which the sls system is not able to prevent successful reflected path interrogations. These include the following situations which are shown diagrammatically in figure 2-22. In each case, the reflected false targets can be generated despite the presence of sls circuitry.

1 Target ranges where UireCt path maln (directional antenna) side-lobe (pl pulse) energy is below the trans~nuer-sensl~i~~~~-

threshold.

Page 39

6340.15 S/31/83

Figure 2-18 PPI TIME EXPOSURE FOR A RADIAL FLIGHT

SHOWING RING -AROUND EFFECTS

SHOWING RING -AROUND EFFECTS

Figure 2-19 SIDE - LOBE SUPRESSION SYSTEM (SLS) AMPLITUDE

RELATIONSHIPS AND ANTENNA PATTERNS

Directional

(PI 8 P3)

Omnidirectional

I f-1

Page 40

Chap 2 Par 23

S/31/83

Figure 2-20 EFFECT BEACON

OF REFLECTED’-PATH

OPERATION

Reflecting

a) Normal Interrogation b) Reflected Path Interrogakion

OF REFLECTED’-PATH

c) Resulting PPI Presentation

arget

Page 41

6340.15 S/31/83

Figure 2-21 SUCCESSFUL SLS ACTION AGAINST REFLECTED PATH INTERROGATION 0

Reflected Interrogation Path

Interrogation Path

Direct lonzi Antenna

(PL and P3)

ional Antenna

a) Pictorial

Direct Path Interrogation Pulses

/. 1 \

Figure 2-21 SUCCESSFUL SLS ACTION AGAINST REFLECTED PATH INTERROGATION 0

P2

RefLected path Interrogzriaq Pulses"

Pl n-

P3

rlr

&/(Delayed due \ longer path

j 3521&S Supyreszion Gate Fcrrnel

b) Transponder Input Pulse Azplitllde Diagram Showing Condition of Imnunit:J to Reflected Path Incerrogation Due to Transponder Suppression - Ko Reply Generated

Page 42

Chap 2 Par 23

5131183 6340.15

Figure 2-22 TRANSPONDER tNPUT PULSE AMPLITUDE DIAGRAMS SHOWING UNSUCCESSFUL SLS

Figure 2-22 TRANSPONDER tNPUT PULSE AMPLITUDE DIAGRAMS SHOWING UNSUCCESSFUL SLS

ACTION AGAINST REFLECTED PATH INTERROGATION

Reflected Path Interrogation Pulses

(Delayed Due to Longer Path) rp-.L-.. ‘--',

4 Transponder Reply to Reflected Signal Path Interrogation Due to Nonrecognition of Direct Path PL (Side-lobe) Pulse

ACTION AGAINST REFLECTED PATH INTERROGATION

Reflected Path Interrogation Pulses

Direct Path (Sidelobes) Interrogation Pulses

I------+

P2 PL r--Pp3-,- 1 n

-- dxansponder

Min.SGsT -- - -

L

' PL P3'

n I Y I

I \ \

i P?

I4L

I 35+1@s Suppression Gate Formed -ReD ly

Initiated

b) Transponder Reply to Reflection Path Interrogation Due

to Path Delay Beyond Duration of Suppression Gate

Reflected Path Interrogation Pulses

Direct Path

Interrogation

c> Transponder Reply to Reflected

Path Interrogation Due to Path DeLay Less Than 2~s.

Reply Initiated

Chap 2 Par 23 Page 43

6340.15 5/31/83

2 Path arrangements where the reflected pulses are received more than 35 + 10 us after direct path pulses.

2 Path arrangements where the reflected pulses are received more that 2 us after direct path pulses.

(5) Improved Side-Lobe Suppression (ISLS).

(a) Introduction. Most ATCSI equipments now incorporate an isls system designed to provide additional immunity against the effects of reflected path interrogation. This is accomplished by allowing the omnidirectional antenna to transmit the Pl interrogation pulse as well as the P2 control pulse, while the directional antenna transmission is unchanged.

(b) Description of Technique. In a reflected path situation, the isls provides the transponder with considerably higher direct-path Pl pulse amplitude, thus more readily allowing the establishment of a suppression gate in the airborne unit. This effect is illustrated in figure 2-23; it reduces to a considerable degree the condition of unsuccessful sls that could occur when direct path illumination is from a cull in the sidelobe pattern as described in subparagraph 23bi3)(d)& abcve. The time related sls deficiencies noted are unaffected by the incorporation of isis, hcwever. It should therefore, be noted that several conditions still occur for which the (isls) system is incapable of preventing successful reflected path interrogation, and hence false targets. These include:

1 Target ranges where direct path omnidirectional antenna energy is below the transponder threshold. This can occur due to blockage effects in addition to range attenuation. Assuming no blockage, the maximum range at which a suppression gate can be generated can be found from figure 2-24.

Continue reading ↓ 120 of 540 passages shown