Radar Vectors
Proposed Rule Proposed Issued Apr 4, 2011 4 pages Copy saved Nov 17, 2026

76 FR 18454 Airworthiness Directives; Burl A. Rogers (Type Certificate Previously Held by William Brad Mitchell and Aeronca, Inc.) Models 15AC and S15AC Airplanes

We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD would require repetitive inspections of the upper and lower main wing spar cap angles for cracks and/or corrosion and installing inspection access panels. This AD would also require replacing the wing spar cap angles if moderate or severe corrosion is found and applying corrosion inhibitor. This proposed AD was prompted by reports of intergranular exfoliation and corrosion of the upper and/or lower wing main spar cap angles found on the affected airplanes. We are proposing this AD to detect and correct cracks, intergranular exfoliation and corrosion in the wing main spar cap angles, which could result in reduced strength of the wing spar and the load carrying capacity of the wing. This could lead to wing failure and consequent loss of control.

This document is proposed. It may have been replaced. Check the official source before relying on it.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2011-0318; Directorate Identifier 2010-CE-033-AD] RIN 2120-AA64

Airworthiness Directives; Burl A. Rogers (Type Certificate Previously Held by William Brad Mitchell and Aeronca, Inc.) Models 15AC and S15AC Airplanes

AGENCY: Federal Aviation Administration (FAA), DOT.

Action

ACTION: Notice of proposed rulemaking (NPRM).

SUMMARY: We propose to adopt a new airworthiness directive (AD) for the products listed above. This proposed AD would require repetitive inspections of the upper and lower main wing spar cap angles for cracks and/or corrosion and installing inspection access panels. This AD would also require replacing the wing spar cap angles if moderate or severe corrosion is found and applying corrosion inhibitor. This proposed AD was prompted by reports of intergranular exfoliation and corrosion of the upper and/or lower wing main spar cap angles found on the affected airplanes. We are proposing this AD to detect and correct cracks, intergranular exfoliation and corrosion in the wing main spar cap angles, which could result in reduced strength of the wing spar and the load carrying capacity of the wing. This could lead to wing failure and consequent loss of control.

Dates

DATES: We must receive comments on this proposed AD by May 19, 2011.

ADDRESSES: You may send comments by any of the following methods:

• Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.

• Fax: 202-493-2251.

• Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590.

Addresses

• Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this proposed AD, contact Burl's Aircraft, LLC, P.O. Box 671487, Chugiak, Alaska 99567-1487; phone: (907) 688-3715; fax (907) 688-5031; e-mail [email protected]; Internet: http://www.burlac.com. You may review copies of the referenced service information at the FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, MO 64106. For information on the availability of this material at the FAA, call (816) 329-4148.

Examining the AD Docket

Examining the AD Docket

You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this proposed AD, the regulatory evaluation, any comments received, and other information. The street address for the Docket Office (phone: 800-647-5527) is in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Eric Wright, Aerospace Engineer, FAA, Anchorage Aircraft Certification Office, 222 W. 7th Ave., 14, Anchorage, Alaska 99513; telephone: (907) 271-2648; fax: (907) 271-6365; e-mail: [email protected].

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to send any written relevant data, views, or arguments about this proposal. Send your comments to an address listed under the ADDRESSES section.

Comments Invited

Include "Docket No. FAA-2011-0318; Directorate Identifier 2010-CE-033-AD" at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of this proposed AD. We will consider all comments received by the closing date and may amend this proposed AD because of those comments.

We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive about this proposed AD.

Discussion

Discussion

Since first discovered in 1998, we have received 34 reports of intergranular corrosion and exfoliation found on the upper and lower wing main spar cap angles on Burl A. Rogers Models 15AC and S15AC airplanes. The cause of the corrosion is unknown and does not have a direct correlation to the type, location, or operation performed by the airplane. In the original type design wing skins, there is a lack of access panels, making the main wing spar caps difficult to inspect. If left undetected, the corrosion in the wing main spar caps could become severe enough to reduce the strength of the spar and the load carrying capacity of the wing. This condition, if not corrected, could result in wing failure. This failure could lead to loss of control.

Relevant Service Information

Relevant Service Information

We have reviewed Burl's Aircraft, LLC Mandatory Service Bulletin No. 15AC06-08-10, dated June 8, 2010.

The service information describes procedures for:

• Inspecting the leading and trailing edges of the upper and lower main wing spar cap angles for cracks, intergranular exfoliation, and corrosion;

• Installing wing inspection access panels;

• Applying corrosion inhibitor on the upper and lower spar cap angles; and

• Replacing the main wing spar cap angles if cracks, intergranular exfoliation, or moderate or severe corrosion is found.

Corrosion definitions and limits are contained in FAA Advisory Circular (AC) 43-4A, paragraph 640 (a)(b)(c).

FAA's Determination

FAA's Determination

We are proposing this AD because we evaluated all the relevant information and determined the unsafe condition described previously is likely to exist or develop in other products of the same type design.

Proposed AD Requirements

This proposed AD would require accomplishing the actions specified in the service information described.

Costs of Compliance

Costs of Compliance

We estimate that this proposed AD would affect 255 airplanes in the U.S. registry.

We estimate the following costs to comply with this proposed AD:

Estimated costs

Cost per Cost on U.S.

Action Labor cost Parts cost product operators

Initial inspection … 10 work-hours x $85 Not applicable … $850 $216,750

per hour = $850.

Installation of inspection access 30 work-hours x $85 $630 … 3,180 810,900

panels and inspection. per hour = $2,550.

We estimate the following costs to do any necessary replacements that would be required based on the results of the proposed inspections. We have no way of determining the number of aircraft that might need these replacements:

On-Condition Costs

Cost per

Action Labor cost Parts cost product per

wing

Replacement of main spar cap … 80 work-hours x $85 per $1,200 per wing … $8,000

hour = $6,800 per wing.

Authority for This Rulemaking

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII: Aviation Programs, describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

Regulatory Findings

We determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify this proposed regulation:

(1) Is not a "significant regulatory action" under Executive Order 12866,

(2) Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979),

(3) Will not affect intrastate aviation in Alaska, and

(4) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. The FAA amends § 39.13 by adding the following new airworthiness directive (AD):

Burl A. Rogers (Type Certificate Previously Held by William Brad Mitchell and Aeronca, Inc.) Models 15AC and S15AC Airplanes: Docket No. FAA-2011-0318; Directorate Identifier 2010-CE-033-AD.

Comments Due Date

Comments Due Date

(a) We must receive comments by May 19, 2011.

Affected ADs

(b) None.

Applicability

(c) This AD applies to Burl A. Rogers (type certificate previously held by William Brad Mitchell and Aeronca, Inc.) Model 15AC and S15AC airplanes, all serial numbers, that are certificated in any category.

Subject

Subject

(d) Joint Aircraft System Component (JASC)/Air Transport Association (ATA) of America Code 57, Wings.

Unsafe Condition

(e) This AD was prompted by reports of intergranular exfoliation and corrosion of the upper and/or lower wing main spar cap angles found on the affected airplanes. We are issuing this AD to detect and correct cracks and corrosion in the wing main spar cap angles, which could result in reduced strength of the wing spar and the load carrying capacity of the wing. This could lead to wing failure and consequent loss of control.

Compliance

Compliance

(f) Comply with this AD within the compliance times specified, unless already done (does not eliminate the repetitive actions of this AD).

Actions Compliance Procedures

(1) Inspect the exposed Within the next 10 Follow Burl's

trailing edges of both the hours time-in- Aircraft, LLC

upper and lower main spar service (TIS) after Mandatory Service

cap angles on both the left the effective date Bulletin No. 15AC06-

and right wing for signs of of this AD or 3 08-10, dated June

cracks, intergranular months after the 8, 2010; and FAA

exfoliation, and corrosion. effective date of Advisory Circular

this AD, whichever (AC) 43.13-1B,

occurs first; or if Change 1, Chapter

the left and/or 6. AC 43.13-1B can

right wing have be found at http://

been repaired and rgl.faa.gov/.

both the upper and

lower main spar

caps have been

replaced using new

parts: Inspect at

or before the next

annual inspection

that occurs 10

years after the

replacement or

within the next 100

hours TIS after the

effective date of

this AD, whichever

occurs later. This

compliance time

applies separately

to each wing. (2) After completing the inspection required in paragraph (f)(1) of this AD:

(i) Install new (i) Install Follow Burl's

inspection hole skin inspection hole Aircraft, LLC

reinforcement doublers skin reinforcement Mandatory Service

and the associated doublers: Within Bulletin No. 15AC06-

screw cover plate in the next 25 hours 08-10, dated June

both the left and right TIS after the 8, 2010; Burl's

wing. effective date of Aircraft, LLC

this AD or within 6 Drawing No. SB

months after the 15AC06-08-10 (not

effective date of dated), and FAA

this AD, whichever Advisory Circular

occurs first; or if (AC) 43.13-1B,

the left and/or Change 1, Chapter

right wing have 6. AC 43.13-1B can

been repaired and be found at http://

both the upper and rgl.faa.gov/.

lower main spar

caps have been

replaced using new

parts: At or before

the next annual

inspection that

occurs 10 years

after the

replacement or

within the next 100

hours TIS after the

effective date of

this AD, whichever

occurs later. This

compliance time

applies separately

to each wing.

(ii) Through the (ii) Inspect: Before

inspection access further flight

panels, inspect the after installing

leading and trailing the inspection hole

edges of both the upper skin reinforcement

and lower main spar cap doublers.

angles on both the left

and right wing for

signs of cracks,

intergranular

exfoliation and

corrosion; and

(iii) Remove any light (iii) Remove

corrosion and treat the corrosion and treat

entirety of both the with corrosion

upper and lower main inhibitor: Before

spar cap angles on both further flight

the left and right wing after the

with corrosion inspection required

inhibitor. in paragraph

(f)(2)(ii) of this

AD.

(3) If cracks, intergranular Before further Follow Burl's

exfoliation, or moderate or flight after the Aircraft, LLC

severe corrosion is found inspection required Mandatory Service

during the inspection in paragraphs Bulletin No. 15AC06-

required in paragraphs (f)(1) and 08-10, dated June

(f)(1) or (f)(2)(ii) of (f)(2)(ii) of this 8, 2010; and

this AD, replace the AD. contact Burl's

affected main spar cap Aircraft, LLC in

angles in their entirety as paragraph (i) of

a single piece. Splicing of this AD for a

the main spar cap angles is replacement scheme

not permitted. and incorporate the

replacement scheme

(4) Removing the wing (i) Repetitively Follow Burl's

inspection access panels, thereafter at Aircraft, LLC

repetitively inspect both intervals not to Mandatory Service

the upper and lower forward exceed every 12 Bulletin No. 15AC06-

main spar caps on both the months after the 08-10, dated June

left and right wing for inspection required 8, 2010; and FAA

signs of cracks, in paragraph Advisory Circular

intergranular exfoliation, (f)(2)(ii) of this (AC) 43.13-1B,

and corrosion. AD. Change 1, Chapter

6. AC 43.13-1B can

be found at http://rgl.faa.gov/. (5) After each inspection required in paragraph (f)(4) of this AD:

(i) If only light Before further Follow Burl's

corrosion is found, flight after each Aircraft, LLC

remove the corrosion inspection required Mandatory Service

and treat the main spar in paragraph (f)(4) Bulletin No. 15AC06-

cap angles with of this AD. 08-10, dated June

corrosion inhibitor;. Continue with the 8, 2010; and FAA

repetitive Advisory Circular

inspections (AC) 43.13-1B,

required in Change 1, Chapter

paragraph (f)(4) of 6. AC 43.13-1B can

this AD. be found at http://rgl.faa.gov/.

Contact Burl's

Aircraft, LLC in

paragraph (i) of

this AD for a

replacement scheme

and incorporate the

replacement scheme.

(ii) If cracks,

intergranular

exfoliation, or

moderate or severe

corrosion is found,

replace the affected

main spar cap angles in

their entirety as a

single piece. Splicing

of the main spar cap

angles is not permitted.

(6) Only install main spar As of the effective Not applicable.

cap angles that have been date of this AD.

inspected and are free of cracks, intergranular exfoliation, or moderate or severe corrosion.

Alternative Methods of Compliance (AMOCs)

Alternative Methods of Compliance (AMOCs)

(g)(1) The Manager, Anchorage Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in the Related Information section of this AD.

(2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office.

Related Information

Related Information

(h) For more information about this AD, contact Eric Wright, Aerospace Engineer, FAA, Anchorage ACO, 222 W. 7th Ave., 14, Anchorage, Alaska 99513; telephone: (907) 271-2648; fax: (907) 271-6365; e-mail: [email protected].

(i) For service information identified in this AD, contact Burl's Aircraft, LLC, P.O. Box 671487, Chugiak, Alaska 99567-1487; telephone: (907) 688-3715; fax (907) 688-5031; e-mail [email protected]; Internet: http://www.burlac.com. You may review copies of the referenced service information at the FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, MO 64106. For information on the availability of this material at the FAA, call (816) 329-4148.

Issued in Kansas City, Missouri, on March 28, 2011. Earl Lawrence, Manager, Small Airplane Directorate, Aircraft Certification Service.