Radar Vectors
Proposed Rule Proposed Issued Nov 12, 2002 4 pages Copy saved Nov 17, 2026

67 FR 68536 Airworthiness Directives; Robert E. Rust Models DeHavilland DH.C1 Chipmunk 21, 22, and 22A Airplanes

This document proposes to adopt a new airworthiness directive (AD) that would apply to certain Robert E. Rust (R.E. Rust) Models DeHavilland DH.C1 Chipmunk 21, 22, and 22A airplanes. This proposed AD would require you to repetitively inspect the tailplane attachment brackets and replace each bracket. This proposed AD would also require you to repetitively inspect each joint of the port and starboard engine mount frame and the rear upper mount frame tubes for cracks and/or damage and repair any cracks and/or damage found. This proposed AD is the result of reports of stress corrosion cracking found on the tailplane attachment brackets and fatigue cracking and chaffing of the engine mount frame. The actions specified by this proposed AD are intended to prevent failure of the tailplane attachment brackets and failure of the engine mount, which could result in loss of the tail section and separation of the engine from the airplane respectively. Such failures could lead to loss of control of the airplane.

This document is proposed. It may have been replaced. Check the official source before relying on it.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. 2000-CE-64-AD] RIN 2120-AA64

Airworthiness Directives; Robert E. Rust Models DeHavilland DH.C1 Chipmunk 21, 22, and 22A Airplanes

AGENCY: Federal Aviation Administration, DOT.

ACTION: Notice of proposed rulemaking (NPRM).

SUMMARY: This document proposes to adopt a new airworthiness directive (AD) that would apply to certain Robert E. Rust (R.E. Rust) Models DeHavilland DH.C1 Chipmunk 21, 22, and 22A airplanes. This proposed AD would require you to repetitively inspect the tailplane attachment brackets and replace each bracket. This proposed AD would also require you to repetitively inspect each joint of the port and starboard engine mount frame and the rear upper mount frame tubes for cracks and/or damage and repair any cracks and/or damage found. This proposed AD is the result of reports of stress corrosion cracking found on the tailplane attachment brackets and fatigue cracking and chaffing of the engine mount frame. The actions specified by this proposed AD are intended to prevent failure of the tailplane attachment brackets and failure of the engine mount, which could result in loss of the tail section and separation of the engine from the airplane respectively. Such failures could lead to loss of control of the airplane.

Dates

DATES: The Federal Aviation Administration (FAA) must receive any comments on this proposed rule on or before January 17, 2003.

ADDRESSES: Submit comments to FAA, Central Region, Office of the Regional Counsel, Attention: Rules Docket No. 2000-CE-64-AD, 901 Locust, Room 506, Kansas City, Missouri 64106. You may view any comments at this location between 8 a.m. and 4 p.m., Monday through Friday, except Federal holidays. You may also send comments electronically to the following address: [email protected]. Comments sent electronically must contain "Docket No. 2000-CE-64-AD" in the subject line. If you send comments electronically as attached electronic files, the files must be formatted in Microsoft Word 97 for Windows or ASCII text.

Addresses

You may get service information that applies to this proposed AD from DeHavilland Support Limited, Duxford Airfield, Bldg. 213, Cambridgeshire, CB2 4QR, United Kingdom, telephone: +44 1223 830090, facsimile: +44 1223 830085, e-mail: [email protected]. You may also view this information at the Rules Docket at the address above.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Cindy Lorenzen, Aerospace Engineer, FAA, Atlanta Aircraft Certification Office, 1895 Phoenix Boulevard, Suite 450, Atlanta, Georgia; telephone: (770) 703-6078; facsimile: (770) 703-6097.

SUPPLEMENTARY INFORMATION:

Comments Invited

How Do I Comment on This Proposed AD?

How Do I Comment on This Proposed AD?

The FAA invites comments on this proposed rule. You may submit whatever written data, views, or arguments you choose. You need to include the rule's docket number and submit your comments to the address specified under the caption ADDRESSES. We will consider all comments received on or before the closing date. We may amend this proposed rule in light of comments received. Factual information that supports your ideas and suggestions is extremely helpful in evaluating the effectiveness of this proposed AD action and determining whether we need to take additional rulemaking action.

Are There Any Specific Portions of This Proposed AD I Should Pay Attention To?

Are There Any Specific Portions of This Proposed AD I Should Pay Attention To?

The FAA specifically invites comments on the overall regulatory, economic, environmental, and energy aspects of this proposed rule that might suggest a need to modify the rule. You may view all comments we receive before and after the closing date of the rule in the Rules Docket. We will file a report in the Rules Docket that summarizes each contact we have with the public that concerns the substantive parts of this proposed AD.

How Can I Be Sure FAA Receives My Comment?

How Can I Be Sure FAA Receives My Comment?

If you want FAA to acknowledge the receipt of your mailed comments, you must include a self-addressed, stamped postcard. On the postcard, write "Comments to Docket No. 2000-CE-64-AD." We will date stamp and mail the postcard back to you.

Discussion

Discussion

What Events Have Caused This Proposed AD?

The FAA has received reports that an unsafe condition may exist on certain R.E. Rust Models DeHavilland DH.C1 Chipmunk 21, 22, and 22A airplanes. After a review of several of these airplanes, stress corrosion cracking was found on the tailplane attachment brackets and fatigue cracks and chaffing were found on the engine mount frame.

What Events Have Caused This Proposed AD?

We have determined that tailplane attachment brackets, pre-modification H357, are made from material susceptible to stress corrosion cracking. Modification No. H357 introduces a new tailplane attachment fitting, part number (P/N) C1.TP.313, that is made from a different type of material than that of the original tailplane attachment fitting, P/N C1.TP.167.

Cracks in the engine mount frame were found in the area of the junction of the front and rear top tube and engine mounting foot support brackets and in the front of the frame. We have determined that fatigue is the cause of the cracks. The upper aft mount frame tubes were also found to have damage caused by chaffing by the cowling support rod.

What Are the Consequences if the Condition Is Not Corrected?

What Are the Consequences if the Condition Is Not Corrected?

These conditions, if not corrected, could result in failure of the tailplane attachment brackets and failure of the engine mount. Such failures could lead to loss of control of the airplane.

Is There Service Information That Applies to This Subject?

Is There Service Information That Applies to This Subject?

British Aerospace (now DeHavilland Support Limited) has issued BAe Aircraft Mandatory Technical News Sheet CT (C1) No. 176, Issue 2, dated November 1, 1997; and BAe Aircraft Mandatory Technical News Sheet CT (C1) No. 190, Issue 2, dated April 1, 1995.

What Are the Provisions of This Service Information?

What Are the Provisions of This Service Information?

BAe Aircraft Mandatory Technical News Sheet CT (C1) No. 176, Issue 2, dated November 1, 1997, includes procedures for:

--Repetitively inspecting the tailplane attachment brackets for cracks; and --Replacing any cracked bracket found upon inspection or as a terminating action for the repetitive inspections.

BAe Aircraft Mandatory Technical News Sheet CT (C1) No. 190, Issue 2, dated April 1, 1995, includes procedures for:

--Repetitively inspecting each joint of the engine mount frame and the rear upper mount frame tubes for cracks and/or damage; and --Repairing any cracks and/or damage found.

The FAA's Determination and an Explanation of the Provisions of this Proposed AD

The FAA's Determination and an Explanation of the Provisions of this Proposed AD

What Has FAA Decided?

After examining the circumstances and reviewing all available information related to the incidents described above, we have determined that:

--The unsafe condition referenced in this document exists or could develop on other R.E. Rust Models DeHavilland DH.C1 Chipmunk 21, 22, and 22A airplanes of the same type design; --The actions specified in the previously-referenced service information should be accomplished on the affected airplanes; and --AD action should be taken in order to correct this unsafe condition.

What Would This Proposed AD Require?

What Would This Proposed AD Require?

This proposed AD would require you to incorporate the actions in the previously-referenced service information.

Cost Impact

How Many Airplanes Would This Proposed AD Impact?

We estimate that this proposed AD affects 54 airplanes in the U.S. registry.

What Would Be the Cost Impact of This Proposed AD on Owners/Operators of the Affected Airplanes?

What Would Be the Cost Impact of This Proposed AD on Owners/Operators of the Affected Airplanes?

We estimate the following costs to accomplish the proposed inspections of the tailplane attachment brackets:

Total cost on U.S.

Labor cost Parts cost Total cost per airplane operators

32 workhours x $60 per hour = No parts required … $1,920 … $1,920 x 54 = $103,680.

$1,920.

We estimate the following costs to accomplish any necessary replacements that would be required based on the results of the proposed inspection. We have no way of determining the number of airplanes that may need such replacement:

Total cost per

Labor cost Parts cost bracket

3 workhours x $60 per hour = $600 per bracket (2 $180 + $600 = $780.

$180 per bracket. brackets per

airplane).

We estimate the following costs to accomplish the proposed inspections of the engine mount frame:

Total cost on U.S.

Labor cost Parts cost Total cost per airplane operators

16 workhours x $60 per hour = No parts required … $960 … $960 x 54 = $51,840.

$960.

The FAA has no method of determining the number of repairs or replacements each owner/operator would incur over the life of each of the affected airplanes based on the results of the proposed inspections. We have no way of determining the number of airplanes that may need such repair. The extent of damage may vary on each airplane.

Compliance Time of This Proposed AD

Compliance Time of This Proposed AD

What Would Be the Compliance Time of This Proposed AD?

The compliance time of this proposed AD is "within the next 90 calendar days after the effective date of this AD."

Why Is the Proposed Compliance Time Presented in Calendar Time Instead of Hours Time-In-Service (TIS)?

Why Is the Proposed Compliance Time Presented in Calendar Time Instead of Hours Time-In-Service (TIS)?

An unsafe condition specified by this proposed AD is caused by corrosion. Corrosion can occur regardless of whether the aircraft is in operation or is in storage. Therefore, to assure that the unsafe condition specified in the proposed AD does not go undetected for a long period of time, the compliance is presented in calendar time instead of hours time-in-service (TIS).

Regulatory Impact

Regulatory Impact

Would This Proposed AD Impact Various Entities?

The regulations proposed herein would not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. Therefore, it is determined that this proposed rule would not have federalism implications under Executive Order 13132.

Would This Proposed AD Involve a Significant Rule or Regulatory Action?

Would This Proposed AD Involve a Significant Rule or Regulatory Action?

For the reasons discussed above, I certify that this proposed action (1) is not a "significant regulatory action" under Executive Order 12866; (2) is not a "significant rule" under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) if promulgated, will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. A copy of the draft regulatory evaluation prepared for this action has been placed in the Rules Docket. A copy of it may be obtained by contacting the Rules Docket at the location provided under the caption ADDRESSES.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the Federal Aviation Administration proposes to amend part 39 of the Federal Aviation Regulations (14 CFR part 39) as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. FAA amends § 39.13 by adding a new airworthiness directive (AD) to read as follows:

Robert E. Rust: Docket No. 2000-CE-64-AD

Robert E. Rust: Docket No. 2000-CE-64-AD

(a) What airplanes are affected by this AD? This AD affects the following R.E. Rust Models DeHavilland DH.C1 Chipmunk 21, 22, and 22A airplanes, serial numbers C1-001 through C1-1014, that are type certificated in any category.

Note 1: We recommend all owners/operators of DeHavilland DH.C1 Chipmunk 21, 22, and 22A airplanes, serial numbers C1-001 through C1-1014, with experimental airworthiness certificates comply with the actions required in this AD.

(b) Who must comply with this AD? Anyone who wishes to operate any of the airplanes identified in paragraph (a) of this AD must comply with this AD.

(c) What problem does this AD address? The actions specified by this AD are intended to prevent failure of the tailplane attachment brackets caused by stress corrosion cracking and failure of the engine mount, which could result in loss of the tail section and separation of the engine from the airplane respectively. Such failures could lead to loss of control of the airplane.

(d) What actions must I accomplish to address this problem? To address this problem, you must accomplish the following:

Compliance Actions Procedures

(1) Tailplane Attachment Brackets

(i) Initially inspect within Inspect, using dye In accordance with

the next 90 days after the penetrant, the British Aerospace

effective date of this AD: tailplane Military Aircraft

(A) Inspect thereafter at attachment and Aerostructures

intervals not to exceed 6 brackets, part- (BAe Aircraft)

months until the number (P/N) Mandatory Technical

modification required by C1.TP.167 (or FAA- News Sheet CT (C1)

paragraph (d)(1)(ii) of the approved equivalent No. 176, Issued 2,

AD is incorporated. part) for cracks. dated November 1,

(B) When the modification 1997; and Civil

required by paragraph Modification

(d)(1)(ii) is incorporated, Mandatory

you may terminate the Modification No.

repetitive inspections of Chipmunk H357,

the tailplane attachment dated March 12,

bracket. 1984.

(ii) At whichever of the Replace the In accordance with

following that occurs tailplane British Aerospace

first: attachment bracket Military Aircraft

(A) Prior to further flight by incorporating and Aerostructures

after the inspection where Modification H357 (BAe Aircraft)

any crack is found; or. (P/N C1.TP.313) or Mandatory Technical

(B) Upon accumulating 9,984 FAA-approved News Sheet CT (C1)

hours time-in-service (the equivalent part No. 176, Issue 2,

safe life limit for P/N number. Installing dated November 1,

C1.TP.167) on the tailplane P/N C1.TP.313 (or 1997; and Civil

attachments brackets or FAA-approved Modification

within the next 90 calendar equivalent part Mandatory

days after the effective number)terminates Modification No.

date of this AD, whichever the repetitive Chipmunk H357,

occurs later. inspection dated March 12,

requirement of the 1984.

tailplane

attachment brackets.

(iii) As of the effective Only install a Not applicable.

date of this AD. tailplane

attachment bracket

that is P/N

C1.TP.313, or FAA-

approved equivalent

part number.

(2) Engine Mount Frames

(i) Inspect each joint of Initially inspect In accordance with

the port and starboard within the next 90 British Aerospace

engine mount frame and the days after the Aerostructures

rear upper mount frame effective date of Limited (BAe

tubes for cracks and/or this AD. Aircraft) Mandatory

damage. Repetitively Technical News

inspect thereafter Sheet CT (C1) No.

at intervals not to 190, Issue 2, dated

exceed 600 hours April 1, 1995.

TIS.

(ii) If cracks and/or damage Prior to further Repair in accordance

is found during any flight after the with AC 43.13-1B,

inspection required in inspection in which Change 1, dated

paragraph (d)(2)(i) of this any crack and/or September 27, 2001,

AD: damage is found. Chapter 4,

(A) Obtain a repair scheme Repetitively Paragraph 4-99 or

from the manufacturer inspect as required in accordance with

through the FAA at the in paragraph the repair scheme

address specified in (d)(2)(i) of this obtained from

paragraph (f) of this AD AD. DeHavilland Support

and incorporate this repair Limited, Duxford

scheme, or repair in Airfield, Bldg.

accordance with FAA 213,

Advisory Circular (AC) Cambridgeshire, CB2

43.13-1B, Change 1, dated 4QR, United

September 27, 2001, Chapter Kingdom. Obtain

4, Paragraph 4-99; or. this repair scheme

(B) Replace with a new or through the FAA at

serviceable part.. the address

specified in

paragraph (f) of

this AD. Replace in

accordance with

British Aerospace

Aerostructures

Limited (BAe

Aircraft) Mandatory

Technical News

Sheet CT (C1) No.

190, Issue 2, dated

April 1, 1995, or

AC 43.13-1B, Change

1, dated September

27, 2001, Chapter

4, Paragraph 4-99.

(3) Bind the rear upper Prior to further In accordance with

mount frame tubes with a flight after the British Aerospace

high density polythene tape initial inspection Aerostructures

at the location where the required in Limited (BAe

cowling support rod clip is paragraph (d)(1) of Aircraft) Mandatory

cowling support rod clip is paragraph (d)(1) of Aircraft) Mandatory

secured. this AD. Technical News

Sheet CT (C1) No.

190, Issue 2, dated

April 1, 1995.

(e) Can I comply with this AD in any other way? You may use an alternative method of compliance or adjust the compliance time if:

(1) Your alternative method of compliance provides an equivalent level of safety; and

(2) The Manager, Atlanta Aircraft Certification Office (ACO), approves your alternative. Submit your request through an FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, Atlanta ACO.

Note 2: This AD applies to each airplane identified in paragraph (a) of this AD, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/ operator must request approval for an alternative method of compliance in accordance with paragraph (e) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if you have not eliminated the unsafe condition, specific actions you propose to address it.

(f) Where can I get information about any already-approved alternative methods of compliance? Contact Cindy Lorenzen, Aerospace Engineer, FAA, Atlanta Aircraft Certification Office, 1895 Phoenix Boulevard, Suite 450, Atlanta, Georgia; telephone: (770) 703-6078; facsimile: (770) 703-6097.

(g) What if I need to fly the airplane to another location to comply with this AD? The FAA can issue a special flight permit under Sec. § 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate your airplane to a location where you can accomplish the requirements of this AD.

(h) How do I get copies of the documents referenced in this AD? You may get copies of the documents referenced in this AD from DeHavilland Support Limited, Duxford Airfield, Bldg. 213, Cambridgeshire, CB2 4QR, United Kingdom, telephone: +44 1223 830090, facsimile: +44 1223 830085, e-mail: [email protected]. You may view these documents at FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106.

Issued in Kansas City, Missouri, on November 4, 2002. Michael Gallagher, Manager, Small Airplane Directorate, Aircraft Certification Service.