FAA-S-ACS-7B Commercial Pilot for Airplane Category Airman Certification Standards
Commercial Pilot for Airplane Category
Airman Certification Standards
FAA-S-ACS-7B
Flight Standards Service
Washington, DC 20591
November 2023
Commercial Pilot for Airplane Category ACS (FAA-S-ACS-7B) i
Foreword
The U.S. Department of Transportation, Federal Aviation Administration (FAA), Office of Safety Standards, Regulatory Support Division, Airman Testing Standards Branch, has published the Commercial Pilot – Airplane Airman Certification Standards (ACS) to communicate the aeronautical knowledge, risk management, and flight proficiency standards for the commercial rating in the airplane category, single-engine land and sea; and multiengine land and sea classes.
This ACS is available for download, in PDF format, from www.faa.gov.
Comments regarding this ACS may be emailed to [email protected].
Material in FAA-S-ACS-7B supersedes FAA-S-ACS-7A, Commercial Pilot – Airplane Airman Certification Standards, Change 1.
The FAA created FAA-G-ACS-2, Airman Certification Standards Companion Guide for Pilots, to provide guidance considered relevant and useful to the community. The number of appendices in the ACS was reduced and much of the non-regulatory material was moved to the Airman Certification Standards Companion Guide for Pilots. Applicants, instructors, and evaluators should consult this companion guide to familiarize themselves with ACS procedures. FAA-G-ACS-2 is available for download, in PDF format, from www.faa.gov.
Commercial Pilot for Airplane Category ACS (FAA-S-ACS-7B) ii
Revision History
Document # Description Date
FAA-S-8081-12C Commercial Pilot Practical Test Standards for Airplane (Changes 1-4) November 2011
FAA-S-ACS-7 Commercial Pilot – Airplane Airman Certification Standards (Changes 1 & 2) June 12, 2017
FAA-S-ACS-7 Commercial Pilot – Airplane Airman Certification Standards (Changes 1, 2, & 3) April 19, 2018
FAA-S-ACS-7A Commercial Pilot – Airplane Airman Certification Standards June 11, 2018
FAA-S-ACS-7A Commercial Pilot – Airplane Airman Certification Standards (Change 1) June 6, 2019
FAA-S-ACS-7B Commercial Pilot for Airplane Category Airman Certification Standards November 2023
Commercial Pilot for Airplane Category ACS (FAA-S-ACS-7B) iii
Major Enhancements to FAA-S-ACS-7B
• The following ACS codes have been added:
• The following ACS codes have been removed and archived. Please see the Airman Certification Standards Companion Guide for Pilots (FAA-G-ACS-2) for more information.
CA.I.F.K2f CA.IV.A.S10 CA.IV.I.S5
CA.IV.K.S7 CA.IV.B.S5 CA.IX.C.K1a
CA.IX.C.K1b CA.IX.C.K1c CA.IX.C.K1d
CA.XI.A.R2 CA.XI.A.S1 CA.XI.B.R2
• Non-regulatory material has been moved from the appendices to the Airman Certification Standards Companion Guide for Pilots (FAA-G-ACS-2).
• Legends have been added to the Additional Ratings Task Tables.
CA.I.B.K4 CA.I.C.K2a CA.I.C.K2b CA.I.C.K2c CA.I.C.K2d CA.I.C.K2e CA.I.C.K2f CA.I.C.K2g CA.I.D.K1a CA.I.D.K6 CA.I.D.R7 CA.I.D.S5 CA.I.E.K4 CA.I.H.R4
CA.I.I.K8 CA.I.I.K9 CA.1.I.R3 CA.1.I.R4 CA.I.I.S5 CA.I.I.S6 CA.II.A.S3 CA.II.A.S4 CA.II.B.K4 CA.II.B.R3 CA.II.B.S4 CA.II.D.R4 CA.II.E.R5 CA.IV.A.R7
CA.IV.A.S6a CA.IV.A.S7a CA.IV.G.S6a CA.IV.I.S4a CA.IV.I.S4b CA.IV.K.S6a CA.IV.K.S6b CA.IV.N.K4 CA.IV.N.R8 CA.IV.N.R9 CA.IV.N.S9 CA.VI.A.R3 CA.VI.B.R5 CA.VI.C.S6
CA.VI.D.S5 CA.VIII.A.S4 CA.VIII.B.K2d CA.VIII.B.S4 CA.IX.A.K4 CA.IX.A.S7 CA.IX.C.R3 CA.IX.C.R4 CA.IX.D.K4 CA.IX.D.K5 CA.IX.D.R2 CA.IX.D.R3 CA.IX.D.S3
iv Commercial Pilot for Airplane Category ACS (FAA-S-ACS-7B)
Introduction
Airman Certification Standards Concept … 1
Area of Operation I. Preflight Preparation
Task A. Pilot Qualifications … 2 Task B. Airworthiness Requirements … 2 Task C. Weather Information … 3 Task D. Cross-Country Flight Planning … 4 Task E. National Airspace System … 5 Task F. Performance and Limitations … 6 Task G. Operation of Systems … 7 Task H. Human Factors … 8 Task I. Water and Seaplane Characteristics, Seaplane Bases, Maritime Rules, and Aids to Marine
Navigation (ASES, AMES) … 9
Area of Operation II. Preflight Procedures
Task A. Preflight Assessment … 11 Task B. Flight Deck Management … 11 Task C. Engine Starting … 12 Task D. Taxiing (ASEL, AMEL) … 12 Task E. Taxiing and Sailing (ASES, AMES) … 14 Task F. Before Takeoff Check … 15
Area of Operation III. Airport and Seaplane Base Operations
Task A. Communications, Light Signals, and Runway Lighting Systems … 16 Task B. Traffic Patterns … 16
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
Task A. Normal Takeoff and Climb … 18 Task B. Normal Approach and Landing … 19 Task C. Soft-Field Takeoff and Climb (ASEL) … 20 Task D. Soft-Field Approach and Landing (ASEL) … 22 Task E. Short-Field Takeoff and Maximum Performance Climb (ASEL, AMEL) … 23 Task F. Short-Field Approach and Landing (ASEL, AMEL) … 24 Task G. Confined Area Takeoff and Maximum Performance Climb (ASES, AMES) … 26 Task H. Confined Area Approach and Landing (ASES, AMES) … 27 Task I. Glassy Water Takeoff and Climb (ASES, AMES) … 28 Task J. Glassy Water Approach and Landing (ASES, AMES) … 30 Task K. Rough Water Takeoff and Climb (ASES, AMES) … 31
Table of Contents
v
Table of Contents
Task L. Rough Water Approach and Landing (ASES, AMES) … 32 Task M. Power-Off 180° Accuracy Approach and Landing (ASEL, ASES) … 33 Task N. Go-Around/Rejected Landing … 34
Area of Operation V. Performance Maneuvers and Ground Reference Maneuvers
Task A. Steep Turns … 36 Task B. Steep Spiral (ASEL, ASES) … 36 Task C. Chandelles (ASEL, ASES) … 37 Task D. Lazy Eights (ASEL, ASES) … 38 Task E. Eights on Pylons (ASEL, ASES) … 39
Area of Operation VI. Navigation
Task A. Pilotage and Dead Reckoning … 41 Task B. Navigation Systems and Radar Services … 42
Task C. Diversion … 42 Task D. Lost Procedures … 43
Area of Operation VII. Slow Flight and Stalls
Task A. Maneuvering During Slow Flight … 45 Task B. Power-Off Stalls … 45 Task C. Power-On Stalls … 47 Task D. Accelerated Stalls … 48 Task E. Spin Awareness … 49
Area of Operation VIII. High-Altitude Operations
Task A. Supplemental Oxygen … 50 Task B. Pressurization … 50
Area of Operation IX. Emergency Operations
Task A. Emergency Descent … 52 Task B. Emergency Approach and Landing (Simulated) (ASEL, ASES) … 52 Task C. Systems and Equipment Malfunctions … 53 Task D. Emergency Equipment and Survival Gear … 54 Task E. Engine Failure During Takeoff Before VMC (Simulated) (AMEL, AMES) … 55 Task F. Engine Failure After Liftoff (Simulated) (AMEL, AMES) … 56 Task G. Approach and Landing with an Inoperative Engine (Simulated)(AMEL, AMES) … 57
Area of Operation X. Multiengine Operations
Task A. Maneuvering with One Engine Inoperative (AMEL, AMES) … 59 Task B. VMC Demonstration (AMEL, AMES) … 60 Task C. One Engine Inoperative (Simulated) (solely by Reference to Instruments) During Straight-
vi
Table of Contents
and-Level Flight and Turns (AMEL, AMES) … 61 Task D. Instrument Approach and Landing with an Inoperative Engine (Simulated) (AMEL, AMES) … 62
Area of Operation XI. Postflight Procedures
Task A. After Landing, Parking, and Securing (ASEL, AMEL) … 64 Task B. Seaplane Post-Landing Procedures (ASES, AMES) … 64
Appendix 1: Practical Test Roles, Responsibilities, and Outcomes
Eligibility Requirements for a Commercial Pilot Certificate … 66 Commercial Pilot Airplane Airman Knowledge Test Table … 66 Use of the ACS During a Practical Test … 66 Instructor Responsibilities … 67 Evaluator Responsibilities … 67 Possible Outcomes of the Test … 68
Time Limit and Credit after a Discontinued Practical Test … 69 Additional Rating Task Table … 69 Addition of an Airplane Single-Engine Land Rating to an Existing Commercial Pilot Certificate … 70 Addition of an Airplane Single-Engine Sea Rating to an Existing Commercial Pilot Certificate … 71 Addition of an Airplane Multiengine Land Rating to an Existing Commercial Pilot Certificate … 72 Addition of an Airplane Multiengine Sea Rating to an Existing Commercial Pilot Certificate … 73 Removal of the “Airplane Multiengine VFR Only” Limitation … 74 Removal of the “Limited to Center Thrust” Limitation … 74
Appendix 2: Safety of Flight
General … 75 Stall and Spin Awareness … 75 Use of Checklists … 75 Positive Exchange of Flight Controls … 75 Use of Distractions … 75 Aeronautical Decision-Making, Risk Management, Crew Resource Management, and Single-Pilot
Resource Management … 75 Multiengine Considerations … 76 Single-Engine Considerations … 76
Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations
Aircraft Requirements & Limitations … 77 Equipment Requirements & Limitations … 77 Use of Flight Simulation Training Devices (FSTD) … 77 Credit for Pilot Time in an FSTD … 77 Use of Aviation Training Devices (ATD) … 77 Credit for Pilot Time in an ATD … 77 Operational Requirements, Limitations, & Task Information … 78
1 Commercial Pilot for Airplane Category ACS (FAA-S-ACS-7B)
Introduction › Airman Certification Standards Concept
Introduction
Airman Certification Standards Concept
The goal of the airman certification process is to ensure the applicant possesses the knowledge, ability to manage risks, and skill consistent with the privileges of the certificate or rating being exercised, in order to act as pilot-in-command (PIC).
Safe operations in today’s National Airspace System (NAS) require the integration of aeronautical knowledge, risk management, and flight proficiency standards. To accomplish these goals, the FAA drew upon the expertise of organizations and individuals across the aviation and training community to develop the ACS. The ACS integrates the elements of knowledge, risk management, and skill required for each airman certificate or rating. It thus forms a more comprehensive standard for what an applicant must know, consider, and do to demonstrate proficiency to pass the tests required for issuance of the applicable airman certificate or rating.
Area of Operation I. Preflight Preparation › Task A. Pilot Qualifications
Area of Operation I. Preflight Preparation
Area of Operation I. Preflight Preparation
Task A. Pilot Qualifications
References: 14 CFR parts 61, 68, 91, 119.1(e); AC 68-1; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with airman and medical certificates including privileges, limitations, currency, and operating as pilot-incommand as a commercial pilot.
Knowledge: The applicant demonstrates understanding of:
CA.I.A.K1 Certification requirements, recent flight experience, and recordkeeping.
CA.I.A.K2 Privileges and limitations.
CA.I.A.K3 Medical certificates: class, expiration, privileges, temporary disqualifications.
CA.I.A.K4 Documents required to exercise commercial pilot privileges.
CA.I.A.K5 Part 68 BasicMed privileges and limitations.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.I.A.R1 Proficiency versus currency.
CA.I.A.R2 Flying unfamiliar aircraft or operating with unfamiliar flight display systems and avionics.
Skills: The applicant exhibits the skill to:
CA.I.A.S1 Apply requirements to act as pilot-in-command (PIC) under Visual Flight Rules (VFR) in a scenario given by the evaluator.
Area of Operation I. Preflight Preparation › Task B. Airworthiness Requirements
Task B. Airworthiness Requirements
References: 14 CFR parts 39, 43, 91; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with airworthiness requirements, including airplane certificates.
Knowledge: The applicant demonstrates understanding of:
CA.I.B.K1 General airworthiness requirements and compliance for airplanes, including:
CA.I.B.K1a a. Location and expiration dates of required aircraft certificates
CA.I.B.K1b b. Required inspections and airplane logbook documentation
CA.I.B.K1c c. Airworthiness Directives and Special Airworthiness Information Bulletins
CA.I.B.K1d d. Purpose and procedure for obtaining a special flight permit
CA.I.B.K2 Pilot-performed preventive maintenance.
CA.I.B.K3 Equipment requirements for day and night VFR flight, including:
CA.I.B.K3a a. Flying with inoperative equipment
CA.I.B.K3b b. Using an approved Minimum Equipment List (MEL)
Area of Operation I. Preflight Preparation
CA.I.B.K3c c. Kinds of Operation Equipment List (KOEL)
CA.I.B.K3d d. Required discrepancy records or placards
CA.I.B.K4 Special airworthiness certificate aircraft operating limitations, if applicable.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.I.B.R1 Inoperative equipment discovered prior to flight.
Skills: The applicant exhibits the skill to:
CA.I.B.S1 Locate and describe airplane airworthiness and registration information.
CA.I.B.S2 Determine the airplane is airworthy in the scenario given by the evaluator.
CA.I.B.S3 Apply appropriate procedures for operating with inoperative equipment in the scenario given by the evaluator.
Area of Operation I. Preflight Preparation › Task C. Weather Information
Task C. Weather Information
References: 14 CFR part 91; AC 91-92; AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25, FAA-H-8083-28
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with weather information for a flight under VFR.
Note: If K2 is selected, the evaluator must assess the applicant’s knowledge of at least three sub-elements.
Note: If K3 is selected, the evaluator must assess the applicant’s knowledge of at least three sub-elements.
Knowledge: The applicant demonstrates understanding of:
CA.I.C.K1 Sources of weather data (e.g., National Weather Service, Flight Service) for flight planning purposes.
CA.I.C.K2 Acceptable weather products and resources required for preflight planning, current and forecast weather for departure, en route, and arrival phases of flight such as:
CA.I.C.K2a a. Airport Observations (METAR and SPECI) and Pilot Observations (PIREP)
CA.I.C.K2b b. Surface Analysis Chart, Ceiling and Visibility Chart (CVA)
CA.I.C.K2c c. Terminal Aerodrome Forecasts (TAF)
CA.I.C.K2d d. Graphical Forecasts for Aviation (GFA)
CA.I.C.K2e e. Wind and Temperature Aloft Forecast (FB)
CA.I.C.K2f f. Convective Outlook (AC)
CA.I.C.K2g g. Inflight Aviation Weather Advisories including Airmen's Meteorological Information (AIRMET),
Significant Meteorological Information (SIGMET), and Convective SIGMET
CA.I.C.K3 Meteorology applicable to the departure, en route, alternate, and destination under visual flight rules (VFR) in Visual Meteorological Conditions (VMC), including expected climate and hazardous conditions such as:
CA.I.C.K3a a. Atmospheric composition and stability
CA.I.C.K3b b. Wind (e.g., windshear, mountain wave, factors affecting wind, etc.)
CA.I.C.K3c c. Temperature and heat exchange
Area of Operation I. Preflight Preparation
CA.I.C.K3d d. Moisture/precipitation
CA.I.C.K3e e. Weather system formation, including air masses and fronts
CA.I.C.K3f f. Clouds
CA.I.C.K3g g. Turbulence
CA.I.C.K3h h. Thunderstorms and microbursts
CA.I.C.K3i i. Icing and freezing level information
CA.I.C.K3j j. Fog/mist
CA.I.C.K3k k. Frost
CA.I.C.K3l l. Obstructions to visibility (e.g., smoke, haze, volcanic ash, etc.)
CA.I.C.K4 Flight deck instrument displays of digital weather and aeronautical information.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.I.C.R1 Making the go/no-go and continue/divert decisions, including:
CA.I.C.R1a a. Circumstances that would make diversion prudent
CA.I.C.R1b b. Personal weather minimums
CA.I.C.R1c c. Hazardous weather conditions, including known or forecast icing or turbulence aloft
CA.I.C.R2 Use and limitations of:
CA.I.C.R2a a. Installed onboard weather equipment
CA.I.C.R2b b. Aviation weather reports and forecasts
CA.I.C.R2c c. Inflight weather resources
Skills: The applicant exhibits the skill to:
CA.I.C.S1 Use available aviation weather resources to obtain an adequate weather briefing.
CA.I.C.S2 Analyze the implications of at least three of the conditions listed in K3a through K3l, using actual weather or weather conditions provided by the evaluator.
CA.I.C.S3 Correlate weather information to make a go/no-go decision.
Area of Operation I. Preflight Preparation › Task D. Cross-Country Flight Planning
Task D. Cross-Country Flight Planning
References: 14 CFR part 91; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; NOTAMs; VFR Navigation Charts
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with cross-country flights and VFR flight planning.
Note: Preparation, presentation, and explanation of a computer-generated flight plan is an acceptable option.
Knowledge: The applicant demonstrates understanding of:
CA.I.D.K1 Route planning, including consideration of different classes and special use airspace (SUA) and selection of appropriate and available navigation/communication systems and facilities.
Area of Operation I. Preflight Preparation
CA.I.D.K1a a. Use of an electronic flight bag (EFB), if used
CA.I.D.K2 Altitude selection accounting for terrain and obstacles, glide distance of airplane, VFR cruising altitudes, and effect of wind.
CA.I.D.K3 Calculating:
CA.I.D.K3a a. Time, climb and descent rates, course, distance, heading, true airspeed, and groundspeed
CA.I.D.K3b b. Estimated time of arrival, including conversion to universal coordinated time (UTC)
CA.I.D.K3c c. Fuel requirements, including reserve
CA.I.D.K4 Elements of a VFR flight plan.
CA.I.D.K5 Procedures for filing, activating, and closing a VFR flight plan.
CA.I.D.K6 Inflight intercept procedures.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.I.D.R1 Pilot.
CA.I.D.R2 Aircraft.
CA.I.D.R3 Environment (e.g., weather, airports, airspace, terrain, obstacles).
CA.I.D.R4 External pressures.
CA.I.D.R5 Limitations of air traffic control (ATC) services.
CA.I.D.R6 Fuel planning.
CA.I.D.R7 Use of an electronic flight bag (EFB), if used.
Skills: The applicant exhibits the skill to:
CA.I.D.S1 Prepare, present, and explain a cross-country flight plan assigned by the evaluator, including a risk analysis based on real-time weather, to the first fuel stop.
CA.I.D.S2 Apply pertinent information from appropriate and current aeronautical charts, Chart Supplements; Notices to Air Missions (NOTAMs) relative to airport, runway and taxiway closures; and other flight publications.
CA.I.D.S3 Create a navigation log and prepare a VFR flight plan.
CA.I.D.S4 Recalculate fuel reserves based on a scenario provided by the evaluator.
CA.I.D.S5 Use an electronic flight bag (EFB), if applicable.
Area of Operation I. Preflight Preparation › Task E. National Airspace System
Task E. National Airspace System
References: 14 CFR parts 71, 91, 93; AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; VFR Navigation Charts
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with National Airspace System (NAS) operations under VFR as a commercial pilot.
Knowledge: The applicant demonstrates understanding of:
CA.I.E.K1 Airspace classes and associated requirements and limitations.
Area of Operation I. Preflight Preparation
CA.I.E.K2 Chart symbols.
CA.I.E.K3 Special use airspace (SUA), special flight rules areas (SFRA), temporary flight restrictions (TFR), and other airspace areas.
CA.I.E.K4 Special visual flight rules (VFR) requirements.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.I.E.R1 Various classes and types of airspace.
Skills: The applicant exhibits the skill to:
CA.I.E.S1 Identify and comply with the requirements for basic VFR weather minimums and flying in particular classes of airspace.
CA.I.E.S2 Correctly identify airspace and operate in accordance with associated communication and equipment requirements.
CA.I.E.S3 Identify the requirements for operating in SUA or within a TFR. Identify and comply with special air traffic rules (SATR) and SFRA operations, if applicable.
Area of Operation I. Preflight Preparation › Task F. Performance and Limitations
Task F. Performance and Limitations
References: FAA-H-8083-1, FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with operating an airplane safely within the parameters of its performance capabilities and limitations.
Knowledge: The applicant demonstrates understanding of:
CA.I.F.K1 Elements related to performance and limitations by explaining the use of charts, tables, and data to determine performance.
CA.I.F.K2 Factors affecting performance, including:
CA.I.F.K2a a. Atmospheric conditions
CA.I.F.K2b b. Pilot technique
CA.I.F.K2c c. Airplane configuration
CA.I.F.K2d d. Airport environment
CA.I.F.K2e e. Loading and weight and balance
CA.I.F.K2f f. [Archived]
CA.I.F.K3 Aerodynamics.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.I.F.R1 Use of performance charts, tables, and data.
CA.I.F.R2 Airplane limitations.
CA.I.F.R3 Possible differences between calculated performance and actual performance.
Skills: The applicant exhibits the skill to:
Area of Operation I. Preflight Preparation
CA.I.F.S1 Compute the weight and balance, correct out-of-CG loading errors and determine if the weight and balance remains within limits during all phases of flight.
CA.I.F.S2 Use the appropriate airplane performance charts, tables, and data.
Area of Operation I. Preflight Preparation › Task G. Operation of Systems
Task G. Operation of Systems
References: FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-23, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with safe operation of systems on the airplane provided for the flight test.
Note: If K1 is selected, the evaluator must assess the applicant's knowledge of at least three sub-elements.
Knowledge: The applicant demonstrates understanding of:
CA.I.G.K1 Airplane systems, including:
CA.I.G.K1a a. Primary flight controls
CA.I.G.K1b b. Secondary flight controls
CA.I.G.K1c c. Powerplant and propeller
CA.I.G.K1d d. Landing gear
CA.I.G.K1e e. Fuel, oil, and hydraulic
CA.I.G.K1f f. Electrical
CA.I.G.K1g g. Avionics
CA.I.G.K1h h. Pitot-static, vacuum/pressure, and associated flight instruments
CA.I.G.K1i i. Environmental
CA.I.G.K1j j. Deicing and anti-icing
CA.I.G.K1k k. Water rudders (ASES, AMES)
CA.I.G.K1l l. Oxygen system
CA.I.G.K2 Indications of and procedures for managing system abnormalities or failures.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.I.G.R1 Detection of system malfunctions or failures.
CA.I.G.R2 Management of a system failure.
CA.I.G.R3 Monitoring and management of automated systems.
Skills: The applicant exhibits the skill to:
CA.I.G.S1 Operate at least three of the systems listed in K1a through K1l appropriately.
CA.I.G.S2 Complete the appropriate checklist(s).
Area of Operation I. Preflight Preparation
Area of Operation I. Preflight Preparation › Task H. Human Factors
Task H. Human Factors
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with personal health, flight physiology, and aeromedical and human factors related to safety of flight.
Knowledge: The applicant demonstrates understanding of:
CA.I.H.K1 Symptoms, recognition, causes, effects, and corrective actions associated with aeromedical and physiological issues, including:
CA.I.H.K1a a. Hypoxia
CA.I.H.K1b b. Hyperventilation
CA.I.H.K1c c. Middle ear and sinus problems
CA.I.H.K1d d. Spatial disorientation
CA.I.H.K1e e. Motion sickness
CA.I.H.K1f f. Carbon monoxide poisoning
CA.I.H.K1g g. Stress
CA.I.H.K1h h. Fatigue
CA.I.H.K1i i. Dehydration and nutrition
CA.I.H.K1j j. Hypothermia
CA.I.H.K1k k. Optical illusions
CA.I.H.K1l l. Dissolved nitrogen in the bloodstream after scuba dives
CA.I.H.K2 Regulations regarding use of alcohol and drugs.
CA.I.H.K3 Effects of alcohol, drugs, and over-the-counter medications.
CA.I.H.K4 Aeronautical Decision-Making (ADM) to include using Crew Resource Management (CRM) or Single- Pilot Resource Management (SRM), as appropriate.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.I.H.R1 Aeromedical and physiological issues.
CA.I.H.R2 Hazardous attitudes.
CA.I.H.R3 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.I.H.R4 Confirmation and expectation bias.
Skills: The applicant exhibits the skill to:
CA.I.H.S1 Associate the symptoms and effects for at least three of the conditions listed in K1a through K1l with the cause(s) and corrective action(s).
CA.I.H.S2 Perform self-assessment, including fitness for flight and personal minimums, for actual flight or a scenario given by the evaluator.
Area of Operation I. Preflight Preparation
Area of Operation I. Preflight Preparation › Task I.
Task I. Water and Seaplane Characteristics, Seaplane Bases, Maritime Rules, and Aids to Marine
Navigation (ASES, AMES)
References: AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-23, FAA-H-8083-25; POH/AFM; USCG Navigation Rules
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with water and seaplane characteristics, seaplane bases, maritime rules, and aids to marine navigation.
Knowledge: The applicant demonstrates understanding of:
CA.I.I.K1 The characteristics of a water surface as affected by features, such as:
CA.I.I.K1a a. Size and location
CA.I.I.K1b b. Protected and unprotected areas
CA.I.I.K1c c. Surface wind
CA.I.I.K1d d. Direction and strength of water current
CA.I.I.K1e e. Floating and partially submerged debris
CA.I.I.K1f f. Sandbars, islands, and shoals
CA.I.I.K1g g. Vessel traffic and wakes
CA.I.I.K1h h. Other characteristics specific to the area
CA.I.I.K1i i. Direction and height of waves
CA.I.I.K2 Float and hull construction, and its effect on seaplane performance.
CA.I.I.K3 Causes of porpoising and skipping, and the pilot action needed to prevent or correct these occurrences.
CA.I.I.K4 How to locate and identify seaplane bases on charts or in directories.
CA.I.I.K5 Operating restrictions at various bases.
CA.I.I.K6 Right-of-way, steering, and sailing rules pertinent to seaplane operation.
CA.I.I.K7 Marine navigation aids, such as buoys, beacons, lights, sound signals, and range markers.
CA.I.I.K8 Naval vessel protection zones.
CA.I.I.K9 No wake zones.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.I.I.R1 Local conditions.
CA.I.I.R2 Impact of marine traffic.
CA.I.I.R3 Right-of-way and sailing rules pertinent to seaplane operations.
CA.I.I.R4 Limited services and assistance available at seaplane bases.
Skills: The applicant exhibits the skill to:
CA.I.I.S1 Assess the water surface characteristics for the proposed flight.
Area of Operation I. Preflight Preparation
CA.I.I.S2 Identify restrictions at local seaplane bases.
CA.I.I.S3 Identify marine navigation aids.
CA.I.I.S4 Describe correct right-of-way, steering, and sailing operations.
CA.I.I.S5 Explain how float and hull construction can affect seaplane performance.
CA.I.I.S6 Describe how to correct for porpoising and skipping.
Area of Operation II. Preflight Procedures › Task A. Preflight Assessment
Area of Operation II. Preflight Procedures
Area of Operation II. Preflight Procedures
Task A. Preflight Assessment
References: FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-23, FAA-H-8083-25, FAA-H-8083-28; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with preparation for safe flight.
Knowledge: The applicant demonstrates understanding of:
CA.II.A.K1 Pilot self-assessment.
CA.II.A.K2 Determining that the airplane to be used is appropriate and airworthy.
CA.II.A.K3 Airplane preflight inspection, including:
CA.II.A.K3a a. Which items should be inspected
CA.II.A.K3b b. The reasons for checking each item
CA.II.A.K3c c. How to detect possible defects
CA.II.A.K3d d. The associated regulations
CA.II.A.K4 Environmental factors, including weather, terrain, route selection, and obstructions.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.II.A.R1 Pilot.
CA.II.A.R2 Aircraft.
CA.II.A.R3 Environment (e.g., weather, airports, airspace, terrain, obstacles).
CA.II.A.R4 External pressures.
CA.II.A.R5 Aviation security concerns.
Skills: The applicant exhibits the skill to:
CA.II.A.S1 Inspect the airplane with reference to an appropriate checklist.
CA.II.A.S2 Verify the airplane is in condition for safe flight and conforms to its type design.
CA.II.A.S3 Perform self-assessment.
CA.II.A.S4 Continue to assess the environment for safe flight.
Area of Operation II. Preflight Procedures › Task B. Flight Deck Management
Task B. Flight Deck Management
References: 14 CFR part 91; AC 120-71; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with flight deck management practices.
Note: See Appendix 2: Safety of Flight.
Knowledge: The applicant demonstrates understanding of:
Area of Operation II. Preflight Procedures
CA.II.B.K1 Passenger briefing requirements, including operation and required use of safety restraint systems.
CA.II.B.K2 Use of appropriate checklists.
CA.II.B.K3 Requirements for current and appropriate navigation data.
CA.II.B.K4 Securing items and cargo.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.II.B.R1 Use of systems or equipment, including automation and portable electronic devices.
CA.II.B.R2 Inoperative equipment.
CA.II.B.R3 Passenger distractions.
Skills: The applicant exhibits the skill to:
CA.II.B.S1 Secure all items in the aircraft.
CA.II.B.S2 Conduct an appropriate passenger briefing, including identifying the pilot-in-command (PIC), use of safety belts, shoulder harnesses, doors, passenger conduct, sterile aircraft, propeller blade avoidance, and emergency procedures.
CA.II.B.S3 Properly program and manage the aircraft’s automation, as applicable.
CA.II.B.S4 Appropriately manage risks by utilizing ADM, including SRM/CRM.
Area of Operation II. Preflight Procedures › Task C. Engine Starting
Task C. Engine Starting
References: FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with recommended engine starting procedures.
Knowledge: The applicant demonstrates understanding of:
CA.II.C.K1 Starting under various conditions.
CA.II.C.K2 Starting the engine(s) by use of external power.
CA.II.C.K3 Engine limitations as they relate to starting.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.II.C.R1 Propeller safety.
Skills: The applicant exhibits the skill to:
CA.II.C.S1 Position the airplane properly considering structures, other aircraft, wind, and the safety of nearby persons and property.
CA.II.C.S2 Complete the appropriate checklist(s).
Area of Operation II. Preflight Procedures › Task D. Taxiing (ASEL, AMEL)
Task D. Taxiing (ASEL, AMEL)
References: AC 91-73; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Area of Operation II. Preflight Procedures
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with taxi operations, including runway incursion avoidance.
Knowledge: The applicant demonstrates understanding of:
CA.II.D.K1 Current airport aeronautical references and information resources such as the Chart Supplement, airport diagram, and Notices to Air Missions (NOTAMs).
CA.II.D.K2 Taxi instructions/clearances.
CA.II.D.K3 Airport markings, signs, and lights.
CA.II.D.K4 Visual indicators for wind.
CA.II.D.K5 Aircraft lighting, as appropriate.
CA.II.D.K6 Procedures for:
CA.II.D.K6a a. Appropriate flight deck activities prior to taxi, including route planning and identifying the
location of Hot Spots
CA.II.D.K6b b. Radio communications at towered and nontowered airports
CA.II.D.K6c c. Entering or crossing runways
CA.II.D.K6d d. Night taxi operations
CA.II.D.K6e e. Low visibility taxi operations
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.II.D.R1 Activities and distractions.
CA.II.D.R2 Confirmation or expectation bias as related to taxi instructions.
CA.II.D.R3 A taxi route or departure runway change.
CA.II.D.R4 Runway incursion.
Skills: The applicant exhibits the skill to:
CA.II.D.S1 Receive and correctly read back clearances/instructions, if applicable.
CA.II.D.S2 Use an airport diagram or taxi chart during taxi, if published, and maintain situational awareness.
CA.II.D.S3 Position the flight controls for the existing wind, if applicable.
CA.II.D.S4 Complete the appropriate checklist(s).
CA.II.D.S5 Perform a brake check immediately after the airplane begins moving.
CA.II.D.S6 Maintain positive control of the airplane during ground operations by controlling direction and speed without excessive use of brakes.
CA.II.D.S7 Comply with airport/taxiway markings, signals, and air traffic control (ATC) clearances and instructions.
CA.II.D.S8 Position the airplane properly relative to hold lines.
Area of Operation II. Preflight Procedures
Area of Operation II. Preflight Procedures › Task E. Taxiing and Sailing (ASES, AMES)
Task E. Taxiing and Sailing (ASES, AMES)
References: AC 91-73; AIM; Chart Supplements; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-23, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with taxiing and sailing operations, including runway incursion avoidance.
Knowledge: The applicant demonstrates understanding of:
CA.II.E.K1 Airport information resources, including Chart Supplements, airport diagram, and appropriate references.
CA.II.E.K2 Taxi instructions/clearances.
CA.II.E.K3 Airport/seaplane base markings, signs, and lights.
CA.II.E.K4 Visual indicators for wind.
CA.II.E.K5 Airplane lighting.
CA.II.E.K6 Procedures for:
CA.II.E.K6a a. Appropriate flight deck activities during taxiing or sailing
CA.II.E.K6b b. Radio communications at towered and nontowered seaplane bases
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.II.E.R1 Activities and distractions.
CA.II.E.R2 Porpoising and skipping.
CA.II.E.R3 Low visibility taxi and sailing operations.
CA.II.E.R4 Other aircraft, vessels, and hazards.
CA.II.E.R5 Confirmation or expectation bias as related to taxi instructions.
Skills: The applicant exhibits the skill to:
CA.II.E.S1 Receive and correctly read back clearances/instructions, if applicable.
CA.II.E.S2 Use an appropriate airport diagram or taxi chart, if published.
CA.II.E.S3 Comply with seaplane base/airport/taxiway markings, signals, and signs.
CA.II.E.S4 Depart the dock/mooring buoy or beach/ramp in a safe manner, considering wind, current, traffic, and hazards.
CA.II.E.S5 Complete the appropriate checklist(s).
CA.II.E.S6 Position the flight controls, flaps, doors, water rudders, and power correctly for the existing conditions to follow the desired course while sailing and to prevent or correct for porpoising and skipping during step taxi.
CA.II.E.S7 Exhibit procedures for steering and maneuvering while maintaining proper situational awareness and desired orientation, path, and position while taxiing using idle, plow, or step taxi technique, as appropriate.
CA.II.E.S8 Plan and follow the most favorable taxi or sailing course for current conditions.
Area of Operation II. Preflight Procedures
CA.II.E.S9 Abide by right-of-way rules, maintain positive airplane control, proper speed, and separation between other aircraft, vessels, and persons.
CA.II.E.S10 Comply with applicable taxi elements in Task D if the practical test is conducted in an amphibious airplane.
Area of Operation II. Preflight Procedures › Task F. Before Takeoff Check
Task F. Before Takeoff Check
References: FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-23, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with before takeoff check.
Knowledge: The applicant demonstrates understanding of:
CA.II.F.K1 Purpose of before takeoff checklist items, including:
CA.II.F.K1a a. Reasons for checking each item
CA.II.F.K1b b. Detecting malfunctions
CA.II.F.K1c c. Ensuring the aircraft is in safe operating condition as recommended by the manufacturer
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.II.F.R1 Division of attention while conducting before takeoff checks.
CA.II.F.R2 Unexpected runway changes by air traffic control (ATC).
CA.II.F.R3 Wake turbulence.
CA.II.F.R4 Potential powerplant failure during takeoff or other malfunction considering operational factors such as airplane characteristics, runway/takeoff path length, surface conditions, environmental conditions, and obstructions.
Skills: The applicant exhibits the skill to:
CA.II.F.S1 Review takeoff performance.
CA.II.F.S2 Complete the appropriate checklist(s).
CA.II.F.S3 Position the airplane appropriately considering wind direction and the presence of any aircraft, vessels, or buildings as applicable.
CA.II.F.S4 Divide attention inside and outside the flight deck.
CA.II.F.S5 Verify that engine parameters and airplane configuration are suitable.
Area of Operation III. Airport and Seaplane Base Operations › Task A. Communications, Light Signals, and Runway Lighting Systems
Area of Operation III. Airport and Seaplane Base Operations
Area of Operation III. Airport and Seaplane Base Operations
Task A. Communications, Light Signals, and Runway Lighting Systems
References: 14 CFR part 91; AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with normal and emergency radio communications, air traffic control (ATC) light signals, and runway lighting systems.
Knowledge: The applicant demonstrates understanding of:
CA.III.A.K1 How to obtain appropriate radio frequencies.
CA.III.A.K2 Proper radio communication procedures and air traffic control (ATC) phraseology.
CA.III.A.K3 ATC light signal recognition.
CA.III.A.K4 Appropriate use of transponder(s).
CA.III.A.K5 Lost communication procedures.
CA.III.A.K6 Equipment issues that could cause loss of communication.
CA.III.A.K7 Radar assistance.
CA.III.A.K8 National Transportation Safety Board (NTSB) accident/incident reporting.
CA.III.A.K9 Runway Status Lighting Systems.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.III.A.R1 Communication.
CA.III.A.R2 Deciding if and when to declare an emergency.
CA.III.A.R3 Use of non-standard phraseology.
Skills: The applicant exhibits the skill to:
CA.III.A.S1 Select and activate appropriate frequencies.
CA.III.A.S2 Transmit using standard phraseology and procedures as specified in the Aeronautical Information Manual (AIM) and Pilot/Controller Glossary.
CA.III.A.S3 Acknowledge radio communications and comply with ATC instructions or as directed by the evaluator.
Area of Operation III. Airport and Seaplane Base Operations › Task B. Traffic Patterns
Task B. Traffic Patterns
References: 14 CFR part 91; AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with traffic patterns.
Knowledge: The applicant demonstrates understanding of:
CA.III.B.K1 Towered and nontowered airport operations.
CA.III.B.K2 Traffic pattern selection for the current conditions.
Area of Operation III. Airport and Seaplane Base Operations
CA.III.B.K3 Right-of-way rules.
CA.III.B.K4 Use of automated weather and airport information.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.III.B.R1 Collision hazards.
CA.III.B.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.III.B.R3 Windshear and wake turbulence.
Skills: The applicant exhibits the skill to:
CA.III.B.S1 Identify and interpret airport/seaplane base runways, taxiways, markings, signs, and lighting.
CA.III.B.S2 Comply with recommended traffic pattern procedures.
CA.III.B.S3 Correct for wind drift to maintain the proper ground track.
CA.III.B.S4 Maintain orientation with the runway/landing area in use.
CA.III.B.S5 Maintain traffic pattern altitude, ±100 feet, and the appropriate airspeed, ±10 knots.
CA.III.B.S6 Maintain situational awareness and proper spacing from other aircraft in the traffic pattern.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds › Task A. Normal Takeoff and Climb
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
Task A. Normal Takeoff and Climb
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-23, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with normal takeoff, climb operations, and rejected takeoff procedures.
Note: If a crosswind condition does not exist, the applicant’s knowledge of crosswind elements must be evaluated through oral testing.
Knowledge: The applicant demonstrates understanding of:
CA.IV.A.K1 Effects of atmospheric conditions, including wind, on takeoff and climb performance.
CA.IV.A.K2 Best angle of climb speed (VX) and best rate of climb speed (VY).
CA.IV.A.K3 Appropriate airplane configuration.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.IV.A.R1 Selection of runway or takeoff path based on aircraft performance and limitations, available distance, and wind.
CA.IV.A.R2 Effects of:
CA.IV.A.R2a a. Crosswind
CA.IV.A.R2b b. Windshear
CA.IV.A.R2c c. Tailwind
CA.IV.A.R2d d. Wake turbulence
CA.IV.A.R2e e. Takeoff surface/condition
CA.IV.A.R3 Abnormal operations, including planning for:
CA.IV.A.R3a a. Rejected takeoff
CA.IV.A.R3b b. Potential engine failure in takeoff/climb phase of flight
CA.IV.A.R4 Collision hazards.
CA.IV.A.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.IV.A.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.IV.A.R7 Runway incursion.
Skills: The applicant exhibits the skill to:
CA.IV.A.S1 Complete the appropriate checklist(s).
CA.IV.A.S2 Make radio calls as appropriate.
CA.IV.A.S3 Verify assigned/correct runway or takeoff path.
CA.IV.A.S4 Determine wind direction with or without visible wind direction indicators.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
CA.IV.A.S5 Position the flight controls for the existing wind, if applicable.
CA.IV.A.S6 Clear the area, taxi into takeoff position, and align the airplane on the runway centerline (ASEL, AMEL) or takeoff path (ASES, AMES).
CA.IV.A.S6a a. Retract the water rudders, as appropriate (ASES, AMES)
CA.IV.A.S7 Advance the throttle smoothly to takeoff power and confirm proper engine and flight instrument indications prior to rotation.
CA.IV.A.S7a a. Establish and maintain the most efficient planing/lift-off attitude, and correct for porpoising or
skipping (ASES, AMES)
CA.IV.A.S8 Avoid excessive water spray on the propeller(s) (ASES, AMES).
CA.IV.A.S9 Rotate and lift off at the recommended airspeed and accelerate to VY.
CA.IV.A.S10 [Archived]
CA.IV.A.S11 Establish a pitch attitude to maintain the manufacturer’s recommended speed or VY, ±5 knots.
CA.IV.A.S12 Configure the airplane in accordance with manufacturer’s guidance.
CA.IV.A.S13 Maintain VY ±5 knots to a safe maneuvering altitude.
CA.IV.A.S14 Maintain directional control and proper wind-drift correction throughout takeoff and climb.
CA.IV.A.S15 Comply with noise abatement procedures, as applicable.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds › Task B. Normal Approach and Landing
Task B. Normal Approach and Landing
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-23, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with normal approach and landing with emphasis on proper use and coordination of flight controls.
Note: If a crosswind condition does not exist, the applicant’s knowledge of crosswind elements must be evaluated through oral testing.
Knowledge: The applicant demonstrates understanding of:
CA.IV.B.K1 A stabilized approach, including energy management concepts.
CA.IV.B.K2 Effects of atmospheric conditions, including wind, on approach and landing performance.
CA.IV.B.K3 Wind correction techniques on approach and landing.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.IV.B.R1 Selection of runway/landing surface, approach path, and touchdown area based on pilot capability, aircraft performance and limitations, available distance, and wind.
CA.IV.B.R2 Effects of:
CA.IV.B.R2a a. Crosswind
CA.IV.B.R2b b. Windshear
CA.IV.B.R2c c. Tailwind
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
CA.IV.B.R2d d. Wake turbulence
CA.IV.B.R2e e. Landing surface/condition
CA.IV.B.R3 Planning for:
CA.IV.B.R3a a. Rejected landing and go-around
CA.IV.B.R3b b. Land and hold short operations (LAHSO)
CA.IV.B.R4 Collision hazards.
CA.IV.B.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.IV.B.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
CA.IV.B.S1 Complete the appropriate checklist(s).
CA.IV.B.S2 Make radio calls as appropriate.
CA.IV.B.S3 Ensure the airplane is aligned with the correct/assigned runway or landing surface.
CA.IV.B.S4 Scan the runway or landing surface and adjoining area for traffic and obstructions.
CA.IV.B.S5 Select and aim for a suitable touchdown point considering the wind conditions, landing surface, and obstructions.
CA.IV.B.S6 Establish the recommended approach and landing configuration, airspeed, and trim, and adjust pitch attitude and power as required to maintain a stabilized approach.
CA.IV.B.S7 Maintain manufacturer’s published approach airspeed or in its absence not more than 1.3 times the stalling speed or the minimum steady flight speed in the landing configuration (VSO), ±5 knots with gust factor applied.
CA.IV.B.S8 Maintain directional control and appropriate crosswind correction throughout the approach and landing.
CA.IV.B.S9 Make smooth, timely, and correct control application during round out and touchdown.
CA.IV.B.S10 Touch down at a proper pitch attitude, within 200 feet beyond or on the specified point, with no side drift, and with the airplane’s longitudinal axis aligned with and over the runway center/landing path.
CA.IV.B.S11 Execute a timely go-around if the approach cannot be made within the tolerances specified above or for any other condition that may result in an unsafe approach or landing.
CA.IV.B.S12 Use runway incursion avoidance procedures, if applicable.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds › Task C. Soft-Field Takeoff and Climb (ASEL)
Task C. Soft-Field Takeoff and Climb (ASEL)
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with soft-field takeoff, climb operations, and rejected takeoff procedures.
Knowledge: The applicant demonstrates understanding of:
CA.IV.C.K1 Effects of atmospheric conditions, including wind, on takeoff and climb performance.
CA.IV.C.K2 Best angle of climb speed (VX) and best rate of climb speed (VY).
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
CA.IV.C.K3 Appropriate airplane configuration.
CA.IV.C.K4 Ground effect.
CA.IV.C.K5 Importance of weight transfer from wheels to wings.
CA.IV.C.K6 Left turning tendencies.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.IV.C.R1 Selection of runway based on pilot capability, airplane performance and limitations, available distance, and wind.
CA.IV.C.R2 Effects of:
CA.IV.C.R2a a. Crosswind
CA.IV.C.R2b b. Windshear
CA.IV.C.R2c c. Tailwind
CA.IV.C.R2d d. Wake turbulence
CA.IV.C.R2e e. Takeoff surface/condition
CA.IV.C.R3 Abnormal operations, including planning for:
CA.IV.C.R3a a. Rejected takeoff
CA.IV.C.R3b b. Potential engine failure in takeoff/climb phase of flight
CA.IV.C.R4 Collision hazards.
CA.IV.C.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.IV.C.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
CA.IV.C.S1 Complete the appropriate checklist(s).
CA.IV.C.S2 Make radio calls as appropriate.
CA.IV.C.S3 Verify assigned/correct runway.
CA.IV.C.S4 Determine wind direction with or without visible wind direction indicators.
CA.IV.C.S5 Position the flight controls for the existing wind, if applicable.
CA.IV.C.S6 Clear the area, maintain necessary flight control inputs, taxi into takeoff position and align the airplane on the runway centerline without stopping, while advancing the throttle smoothly to takeoff power.
CA.IV.C.S7 Confirm takeoff power and proper engine and flight instrument indications.
CA.IV.C.S8 Establish and maintain a pitch attitude that transfers the weight of the airplane from the wheels to the wings as rapidly as possible.
CA.IV.C.S9 Lift off at the lowest possible airspeed and remain in ground effect while accelerating to VX or VY, as appropriate.
CA.IV.C.S10 Establish a pitch attitude for VX or VY, as appropriate, and maintain selected airspeed ±5 knots during the climb.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
CA.IV.C.S11 Configure the airplane after a positive rate of climb has been verified or in accordance with airplane manufacturer’s instructions.
CA.IV.C.S12 Maintain VX or VY, as appropriate, ±5 knots to a safe maneuvering altitude.
CA.IV.C.S13 Maintain directional control and proper wind-drift correction throughout takeoff and climb.
CA.IV.C.S14 Comply with noise abatement procedures, as applicable.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds › Task D. Soft-Field Approach and Landing (ASEL)
Task D. Soft-Field Approach and Landing (ASEL)
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with soft-field approach and landing with emphasis on proper use and coordination of flight controls.
Knowledge: The applicant demonstrates understanding of:
CA.IV.D.K1 A stabilized approach, including energy management concepts.
CA.IV.D.K2 Effects of atmospheric conditions, including wind, on approach and landing performance.
CA.IV.D.K3 Wind correction techniques on approach and landing.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.IV.D.R1 Selection of runway based on pilot capability, airplane performance and limitations, available distance, and wind.
CA.IV.D.R2 Effects of:
CA.IV.D.R2a a. Crosswind
CA.IV.D.R2b b. Windshear
CA.IV.D.R2c c. Tailwind
CA.IV.D.R2d d. Wake turbulence
CA.IV.D.R2e e. Landing surface/condition
CA.IV.D.R3 Planning for:
CA.IV.D.R3a a. Rejected landing and go-around
CA.IV.D.R3b b. Land and hold short operations (LAHSO)
CA.IV.D.R4 Collision hazards.
CA.IV.D.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.IV.D.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
CA.IV.D.S1 Complete the appropriate checklist(s).
CA.IV.D.S2 Make radio calls as appropriate.
CA.IV.D.S3 Ensure the airplane is aligned with the correct/assigned runway.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
CA.IV.D.S4 Scan the landing runway and adjoining area for traffic and obstructions.
CA.IV.D.S5 Select and aim for a suitable touchdown point considering the wind conditions, landing surface, and obstructions.
CA.IV.D.S6 Establish the recommended approach and landing configuration, airspeed, and trim, and adjust pitch attitude and power as required to maintain a stabilized approach.
CA.IV.D.S7 Maintain manufacturer’s published approach airspeed or in its absence not more than 1.3 times the stalling speed or the minimum steady flight speed in the landing configuration (VSO), ±5 knots with gust factor applied.
CA.IV.D.S8 Maintain directional control and appropriate crosswind correction throughout the approach and landing.
CA.IV.D.S9 Make smooth, timely, and correct control inputs during the round out and touchdown, and, for tricycle gear airplanes, keep the nose wheel off the surface until loss of elevator effectiveness.
CA.IV.D.S10 Touch down at a proper pitch attitude with minimum sink rate, no side drift, and with the airplane’s longitudinal axis aligned with the center of the runway.
CA.IV.D.S11 Maintain elevator as recommended by manufacturer during rollout and exit the “soft” area at a speed that would preclude sinking into the surface.
CA.IV.D.S12 Execute a timely go-around if the approach cannot be made within the tolerances specified above or for any other condition that may result in an unsafe approach or landing.
CA.IV.D.S13 Maintain proper position of the flight controls and sufficient speed to taxi while on the soft surface.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds › Task E. Short-Field Takeoff and Maximum Performance Climb (ASEL, AMEL)
Task E. Short-Field Takeoff and Maximum Performance Climb (ASEL, AMEL)
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with short-field takeoff, maximum performance climb operations, and rejected takeoff procedures.
Knowledge: The applicant demonstrates understanding of:
CA.IV.E.K1 Effects of atmospheric conditions, including wind, on takeoff and climb performance.
CA.IV.E.K2 Best angle of climb speed (VX) and best rate of climb speed (VY).
CA.IV.E.K3 Appropriate airplane configuration.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.IV.E.R1 Selection of runway based on pilot capability, airplane performance and limitations, available distance, and wind.
CA.IV.E.R2 Effects of:
CA.IV.E.R2a a. Crosswind
CA.IV.E.R2b b. Windshear
CA.IV.E.R2c c. Tailwind
CA.IV.E.R2d d. Wake turbulence
CA.IV.E.R2e e. Takeoff surface/condition
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
CA.IV.E.R3 Abnormal operations, including planning for:
CA.IV.E.R3a a. Rejected takeoff
CA.IV.E.R3b b. Potential engine failure in takeoff/climb phase of flight
CA.IV.E.R4 Collision hazards.
CA.IV.E.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.IV.E.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
CA.IV.E.S1 Complete the appropriate checklist(s).
CA.IV.E.S2 Make radio calls as appropriate.
CA.IV.E.S3 Verify assigned/correct runway.
CA.IV.E.S4 Determine wind direction with or without visible wind direction indicators.
CA.IV.E.S5 Position the flight controls for the existing wind, if applicable.
CA.IV.E.S6 Clear the area, taxi into takeoff position, and align the airplane on the runway centerline utilizing maximum available takeoff area.
CA.IV.E.S7 Apply brakes while setting engine power to achieve maximum performance.
CA.IV.E.S8 Confirm takeoff power prior to brake release and verify proper engine and flight instrument indications prior to rotation.
CA.IV.E.S9 Rotate and lift off at the recommended airspeed and accelerate to the recommended obstacle clearance airspeed or VX, ±5 knots.
CA.IV.E.S10 Establish a pitch attitude to maintain the recommended obstacle clearance airspeed or VX, ±5 knots until the obstacle is cleared or until the airplane is 50 feet above the surface.
CA.IV.E.S11 Establish a pitch attitude for VY and accelerate to VY ±5 knots after clearing the obstacle or at 50 feet above ground level (AGL) if simulating an obstacle.
CA.IV.E.S12 Configure the airplane in accordance with the manufacturer’s guidance after a positive rate of climb has been verified.
CA.IV.E.S13 Maintain VY ±5 knots to a safe maneuvering altitude.
CA.IV.E.S14 Maintain directional control and proper wind-drift correction throughout takeoff and climb.
CA.IV.E.S15 Comply with noise abatement procedures, as applicable.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds › Task F. Short-Field Approach and Landing (ASEL, AMEL)
Task F. Short-Field Approach and Landing (ASEL, AMEL)
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with short-field approach and landing with emphasis on proper use and coordination of flight controls.
Knowledge: The applicant demonstrates understanding of:
CA.IV.F.K1 A stabilized approach, including energy management concepts.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
CA.IV.F.K2 Effects of atmospheric conditions, including wind, on approach and landing performance.
CA.IV.F.K3 Wind correction techniques on approach and landing.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.IV.F.R1 Selection of runway based on pilot capability, airplane performance and limitations, available distance, and wind.
CA.IV.F.R2 Effects of:
CA.IV.F.R2a a. Crosswind
CA.IV.F.R2b b. Windshear
CA.IV.F.R2c c. Tailwind
CA.IV.F.R2d d. Wake turbulence
CA.IV.F.R2e e. Landing surface/condition
CA.IV.F.R3 Planning for:
CA.IV.F.R3a a. Rejected landing and go-around
CA.IV.F.R3b b. Land and hold short operations (LAHSO)
CA.IV.F.R4 Collision hazards.
CA.IV.F.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.IV.F.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
CA.IV.F.S1 Complete the appropriate checklist(s).
CA.IV.F.S2 Make radio calls as appropriate.
CA.IV.F.S3 Ensure the airplane is aligned with the correct/assigned runway.
CA.IV.F.S4 Scan the landing runway and adjoining area for traffic and obstructions.
CA.IV.F.S5 Select and aim for a suitable touchdown point considering the wind conditions, landing surface, and obstructions.
CA.IV.F.S6 Establish the recommended approach and landing configuration, airspeed, and trim, and adjust pitch attitude and power as required to maintain a stabilized approach.
CA.IV.F.S7 Maintain manufacturer’s published approach airspeed or in its absence not more than 1.3 times the stalling speed or the minimum steady flight speed in the landing configuration (VSO), ±5 knots with gust factor applied.
CA.IV.F.S8 Maintain directional control and appropriate crosswind correction throughout the approach and landing.
CA.IV.F.S9 Make smooth, timely, and correct control application before, during, and after touchdown.
CA.IV.F.S10 Touch down at a proper pitch attitude within 100 feet beyond or on the specified point, threshold markings, or runway numbers, with no side drift, minimum float, and with the airplane’s longitudinal axis aligned with and over the runway centerline.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
CA.IV.F.S11 Use manufacturer’s recommended procedures for airplane configuration and braking.
CA.IV.F.S12 Execute a timely go-around if the approach cannot be made within the tolerances specified above or for any other condition that may result in an unsafe approach or landing.
CA.IV.F.S13 Use runway incursion avoidance procedures, if applicable.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds › Task G. Confined Area Takeoff and Maximum Performance Climb (ASES, AMES)
Task G. Confined Area Takeoff and Maximum Performance Climb (ASES, AMES)
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-23, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with confined area takeoff and maximum performance climb.
Knowledge: The applicant demonstrates understanding of:
CA.IV.G.K1 Effects of atmospheric conditions, including wind, on takeoff and climb performance.
CA.IV.G.K2 Best angle of climb speed (VX) and best rate of climb speed (VY).
CA.IV.G.K3 Appropriate airplane configuration.
CA.IV.G.K4 Effects of water surface.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.IV.G.R1 Selection of takeoff path based on pilot capability, airplane performance and limitations, available distance, and wind.
CA.IV.G.R2 Effects of:
CA.IV.G.R2a a. Crosswind
CA.IV.G.R2b b. Windshear
CA.IV.G.R2c c. Tailwind
CA.IV.G.R2d d. Wake turbulence
CA.IV.G.R2e e. Water surface/condition
CA.IV.G.R3 Abnormal operations, including planning for:
CA.IV.G.R3a a. Rejected takeoff
CA.IV.G.R3b b. Potential engine failure in takeoff/climb phase of flight
CA.IV.G.R4 Collision hazards.
CA.IV.G.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.IV.G.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
CA.IV.G.S1 Complete the appropriate checklist(s).
CA.IV.G.S2 Make radio calls as appropriate.
CA.IV.G.S3 Verify assigned/correct takeoff path.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
CA.IV.G.S4 Determine wind direction with or without visible wind direction indicators.
CA.IV.G.S5 Position the flight controls for the existing wind, if applicable.
CA.IV.G.S6 Clear the area, taxi into takeoff position utilizing maximum available takeoff area, and align the airplane on the takeoff path.
CA.IV.G.S6a a. Retract the water rudders, as appropriate
CA.IV.G.S7 Advance the throttle smoothly to takeoff power and confirm proper engine and flight instrument indications prior to rotation.
CA.IV.G.S8 Establish a pitch attitude that maintains the most efficient planing/lift-off attitude and correct for porpoising and skipping.
CA.IV.G.S9 Avoid excessive water spray on the propeller(s).
CA.IV.G.S10 Rotate and lift off at the recommended airspeed, and accelerate to the recommended obstacle clearance airspeed or VX.
CA.IV.G.S11 Establish a pitch attitude to maintain the recommended obstacle clearance airspeed or VX, ±5 knots until the obstacle is cleared or until the airplane is 50 feet above the surface.
CA.IV.G.S12 Establish a pitch attitude for VY and accelerate to VY ±5 knots after clearing the obstacle or at 50 feet above ground level (AGL) if simulating an obstacle.
CA.IV.G.S13 Retract flaps, if extended, after a positive rate of climb has been verified or in accordance with airplane manufacturer’s guidance.
CA.IV.G.S14 Maintain VY ±5 knots to a safe maneuvering altitude.
CA.IV.G.S15 Maintain directional control and proper wind-drift correction throughout takeoff and climb.
CA.IV.G.S16 Comply with noise abatement procedures, as applicable.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds › Task H. Confined Area Approach and Landing (ASES, AMES)
Task H. Confined Area Approach and Landing (ASES, AMES)
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-23, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with confined area approach and landing.
Knowledge: The applicant demonstrates understanding of:
CA.IV.H.K1 A stabilized approach, including energy management concepts.
CA.IV.H.K2 Effects of atmospheric conditions, including wind, on approach and landing performance.
CA.IV.H.K3 Wind correction techniques on approach and landing.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.IV.H.R1 Selection of approach path and touchdown area based on pilot capability, airplane performance and limitations, available distance, and wind.
CA.IV.H.R2 Effects of:
CA.IV.H.R2a a. Crosswind
CA.IV.H.R2b b. Windshear
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
CA.IV.H.R2c c. Tailwind
CA.IV.H.R2d d. Wake turbulence
CA.IV.H.R2e e. Water surface/condition
CA.IV.H.R3 Planning for a go-around and rejected landing.
CA.IV.H.R4 Collision hazards.
CA.IV.H.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.IV.H.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
CA.IV.H.S1 Complete the appropriate checklist(s).
CA.IV.H.S2 Make radio calls as appropriate.
CA.IV.H.S3 Ensure the airplane is aligned for an approach to the correct/assigned landing surface.
CA.IV.H.S4 Scan the landing area for traffic and obstructions.
CA.IV.H.S5 Select and aim for a suitable touchdown point considering the wind conditions, landing surface, and obstructions.
CA.IV.H.S6 Establish the recommended approach and landing configuration, airspeed, and trim, and adjust pitch attitude and power as required to maintain a stabilized approach.
CA.IV.H.S7 Maintain manufacturer’s published approach airspeed or in its absence not more than 1.3 VSO, +10/-5 knots with gust factor applied.
CA.IV.H.S8 Maintain directional control and appropriate crosswind correction throughout the approach and landing.
CA.IV.H.S9 Make smooth, timely, and correct control application before, during, and after touchdown.
CA.IV.H.S10 Contact the water at the recommended airspeed with a proper pitch attitude for the surface conditions.
CA.IV.H.S11 Touch down at a proper pitch attitude, within 100 feet beyond or on the specified point, with no side drift, minimum float, and with the airplane’s longitudinal axis aligned with the projected landing path.
CA.IV.H.S12 Execute a timely go-around if the approach cannot be made within the tolerances specified above or for any other condition that may result in an unsafe approach or landing.
CA.IV.H.S13 Apply elevator control as necessary to stop in the shortest distance consistent with safety.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds › Task I. Glassy Water Takeoff and Climb (ASES, AMES)
Task I. Glassy Water Takeoff and Climb (ASES, AMES)
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-23, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with glassy water takeoff and climb.
Note: If a glassy water condition does not exist, the applicant must be evaluated by simulating the Task.
Knowledge: The applicant demonstrates understanding of:
CA.IV.I.K1 Effects of atmospheric conditions, including wind, on takeoff and climb performance.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
CA.IV.I.K2 Best angle of climb speed (VX) and best rate of climb speed (VY).
CA.IV.I.K3 Appropriate airplane configuration.
CA.IV.I.K4 Appropriate use of glassy water takeoff and climb technique.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.IV.I.R1 Selection of takeoff path based on pilot capability, airplane performance and limitations, and available distance.
CA.IV.I.R2 Water surface/condition.
CA.IV.I.R3 Abnormal operations, including planning for:
CA.IV.I.R3a a. Rejected takeoff
CA.IV.I.R3b b. Potential engine failure in takeoff/climb phase of flight
CA.IV.I.R4 Collision hazards.
CA.IV.I.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.IV.I.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.IV.I.R7 Gear position in an amphibious airplane.
Skills: The applicant exhibits the skill to:
CA.IV.I.S1 Complete the appropriate checklist(s).
CA.IV.I.S2 Make radio calls as appropriate.
CA.IV.I.S3 Position flight controls and configure the aircraft for the existing conditions.
CA.IV.I.S4 Clear the area, select appropriate takeoff path considering surface hazards or vessels and surface conditions.
CA.IV.I.S4a a. Retract the water rudders, as appropriate
CA.IV.I.S4b b. Advance the throttle smoothly to takeoff power and confirm proper engine and flight
instrument indications prior to rotation
CA.IV.I.S5 [Archived]
CA.IV.I.S6 Establish and maintain an appropriate planing attitude, directional control, and correct for porpoising, skipping, and increase in water drag.
CA.IV.I.S7 Avoid excessive water spray on the propeller(s).
CA.IV.I.S8 Use appropriate techniques to lift seaplane from the water considering surface conditions.
CA.IV.I.S9 Establish proper attitude/airspeed and accelerate to VY ±5 knots during the climb.
CA.IV.I.S10 Configure the airplane after a positive rate of climb has been verified or in accordance with airplane manufacturer’s instructions.
CA.IV.I.S11 Maintain VY ±5 knots to a safe maneuvering altitude.
CA.IV.I.S12 Maintain directional control throughout takeoff and climb.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
Area of Operation IV. Takeoffs, Landings, and Go-Arounds › Task J. Glassy Water Approach and Landing (ASES, AMES)
Task J. Glassy Water Approach and Landing (ASES, AMES)
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-23, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with glassy water approach and landing.
Note: If a glassy water condition does not exist, the applicant must be evaluated by simulating the Task.
Knowledge: The applicant demonstrates understanding of:
CA.IV.J.K1 A stabilized approach, including energy management concepts.
CA.IV.J.K2 Effects of atmospheric conditions, including wind, on approach and landing performance.
CA.IV.J.K3 When and why glassy water techniques are used.
CA.IV.J.K4 How a glassy water approach and landing is executed.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.IV.J.R1 Selection of approach path and touchdown area based on pilot capability, airplane performance and limitations, and available distance.
CA.IV.J.R2 Water surface/condition.
CA.IV.J.R3 Planning for a go-around and rejected landing.
CA.IV.J.R4 Collision hazards.
CA.IV.J.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.IV.J.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.IV.J.R7 Gear position in an amphibious airplane.
Skills: The applicant exhibits the skill to:
CA.IV.J.S1 Complete the appropriate checklist(s).
CA.IV.J.S2 Make radio calls as appropriate.
CA.IV.J.S3 Scan the landing area for traffic and obstructions.
CA.IV.J.S4 Select a proper approach and landing path considering the landing surface, visual attitude references, water depth, and collision hazards.
CA.IV.J.S5 Establish the recommended approach and landing configuration, airspeed, and trim, and adjust pitch attitude and power as required to maintain a stabilized approach.
CA.IV.J.S6 Maintain manufacturer’s published approach airspeed or in its absence not more than 1.3 VSO, ±5 knots.
CA.IV.J.S7 Make smooth, timely, and correct power and control adjustments to maintain proper pitch attitude and rate of descent to touchdown.
CA.IV.J.S8 Contact the water in a proper pitch attitude, and slow to idle taxi speed.
CA.IV.J.S9 Maintain directional control throughout the approach and landing.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
Area of Operation IV. Takeoffs, Landings, and Go-Arounds › Task K. Rough Water Takeoff and Climb (ASES, AMES)
Task K. Rough Water Takeoff and Climb (ASES, AMES)
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-23, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with rough water takeoff and climb.
Note: If a rough water condition does not exist, the applicant must be evaluated by simulating the Task.
Knowledge: The applicant demonstrates understanding of:
CA.IV.K.K1 Effects of atmospheric conditions, including wind, on takeoff and climb performance.
CA.IV.K.K2 Best angle of climb speed (VX) and best rate of climb speed (VY).
CA.IV.K.K3 Appropriate airplane configuration.
CA.IV.K.K4 Appropriate use of rough water takeoff and climb technique.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.IV.K.R1 Selection of takeoff path based on pilot capability, airplane performance and limitations, available distance, and wind.
CA.IV.K.R2 Effects of:
CA.IV.K.R2a a. Crosswind
CA.IV.K.R2b b. Windshear
CA.IV.K.R2c c. Tailwind
CA.IV.K.R2d d. Wake turbulence
CA.IV.K.R2e e. Water surface/condition
CA.IV.K.R3 Abnormal operations, including planning for:
CA.IV.K.R3a a. Rejected takeoff
CA.IV.K.R3b b. Potential engine failure in takeoff/climb phase of flight
CA.IV.K.R4 Collision hazards.
CA.IV.K.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.IV.K.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.IV.K.R7 Gear position in an amphibious airplane.
Skills: The applicant exhibits the skill to:
CA.IV.K.S1 Complete the appropriate checklist(s).
CA.IV.K.S2 Make radio calls as appropriate.
CA.IV.K.S3 Verify assigned/correct takeoff path.
CA.IV.K.S4 Determine wind direction with or without visible wind direction indicators.
CA.IV.K.S5 Position flight controls and configure the airplane for the existing conditions.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
CA.IV.K.S6 Clear the area, select an appropriate takeoff path considering wind, swells, surface hazards, or vessels.
CA.IV.K.S6a a. Retract the water rudders, as appropriate
CA.IV.K.S6b b. Advance the throttle smoothly to takeoff power and confirm proper engine and flight
instrument indications prior to rotation
CA.IV.K.S7 [Archived]
CA.IV.K.S8 Establish and maintain an appropriate planing attitude, directional control, and correct for porpoising, skipping, and increase in water drag.
CA.IV.K.S9 Avoid excessive water spray on the propeller(s).
CA.IV.K.S10 Lift off at minimum airspeed and accelerate to VY ±5 knots before leaving ground effect.
CA.IV.K.S11 Configure the airplane after a positive rate of climb has been verified or in accordance with airplane manufacturer’s instructions.
CA.IV.K.S12 Maintain VY ±5 knots to a safe maneuvering altitude.
CA.IV.K.S13 Maintain directional control and proper wind-drift correction throughout takeoff and climb.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds › Task L. Rough Water Approach and Landing (ASES, AMES)
Task L. Rough Water Approach and Landing (ASES, AMES)
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-23, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with rough water approach and landing.
Note: If a rough water condition does not exist, the applicant must be evaluated by simulating the Task.
Knowledge: The applicant demonstrates understanding of:
CA.IV.L.K1 A stabilized approach, including energy management concepts.
CA.IV.L.K2 Effects of atmospheric conditions, including wind, on approach and landing performance.
CA.IV.L.K3 Wind correction techniques on approach and landing.
CA.IV.L.K4 When and why rough water techniques are used.
CA.IV.L.K5 How to perform a proper rough water approach and landing.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.IV.L.R1 Selection of approach path and touchdown area based on pilot capability, airplane performance and limitations, available distance, and wind.
CA.IV.L.R2 Effects of:
CA.IV.L.R2a a. Crosswind
CA.IV.L.R2b b. Windshear
CA.IV.L.R2c c. Tailwind
CA.IV.L.R2d d. Wake turbulence
CA.IV.L.R2e e. Water surface/condition
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
CA.IV.L.R3 Planning for a go-around and rejected landing.
CA.IV.L.R4 Collision hazards.
CA.IV.L.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.IV.L.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.IV.L.R7 Gear position in an amphibious airplane.
Skills: The applicant exhibits the skill to:
CA.IV.L.S1 Complete the appropriate checklist(s).
CA.IV.L.S2 Make radio calls as appropriate.
CA.IV.L.S3 Ensure the airplane is aligned with the correct/assigned waterway.
CA.IV.L.S4 Scan the landing area for traffic and obstructions.
CA.IV.L.S5 Select and aim for a suitable touchdown point considering the wind conditions, landing surface, and obstructions.
CA.IV.L.S6 Establish the recommended approach and landing configuration, airspeed, and trim, and adjust pitch attitude and power as required to maintain a stabilized approach.
CA.IV.L.S7 Maintain manufacturer’s published approach airspeed or in its absence not more than 1.3 times the stalling speed or the minimum steady flight speed in the landing configuration (VSO), ±5 knots with gust factor applied.
CA.IV.L.S8 Maintain directional control and appropriate crosswind correction throughout the approach and landing.
CA.IV.L.S9 Make smooth, timely, and correct power and control adjustments to maintain proper pitch attitude and rate of descent to touchdown.
CA.IV.L.S10 Contact the water in a proper pitch attitude, considering the type of rough water.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds › Task M. Power-Off 180° Accuracy Approach and Landing (ASEL, ASES)
Task M. Power-Off 180° Accuracy Approach and Landing (ASEL, ASES)
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with power-off 180° accuracy approach and landing.
Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Knowledge: The applicant demonstrates understanding of:
CA.IV.M.K1 A stabilized approach, including energy management concepts.
CA.IV.M.K2 Effects of atmospheric conditions, including wind, on approach and landing.
CA.IV.M.K3 Wind correction techniques on approach and landing.
CA.IV.M.K4 Purpose of power-off accuracy approach.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
CA.IV.M.R1 Selection of runway/landing surface, approach path, and touchdown area based on pilot capability, aircraft performance and limitations, available distance, and wind.
CA.IV.M.R2 Effects of:
CA.IV.M.R2a a. Crosswind
CA.IV.M.R2b b. Windshear
CA.IV.M.R2c c. Tailwind
CA.IV.M.R2d d. Wake turbulence
CA.IV.M.R2e e. Landing surface/condition
CA.IV.M.R3 Planning for:
CA.IV.M.R3a a. Rejected landing and go-around
CA.IV.M.R3b b. Land and hold short operations (LAHSO)
CA.IV.M.R4 Collision hazards.
CA.IV.M.R5 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.IV.M.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.IV.M.R7 Forward slip operations, including fuel flowage, tail stalls with flaps, and airspeed control.
Skills: The applicant exhibits the skill to:
CA.IV.M.S1 Complete the appropriate checklist(s).
CA.IV.M.S2 Make radio calls as appropriate.
CA.IV.M.S3 Plan and follow a flightpath to the selected landing area considering altitude, wind, terrain, and obstructions.
CA.IV.M.S4 Select the most suitable touchdown point based on wind, landing surface, obstructions, and aircraft limitations.
CA.IV.M.S5 Position airplane on downwind leg, parallel to landing runway.
CA.IV.M.S6 Correctly configure the airplane.
CA.IV.M.S7 As necessary, correlate crosswind with direction of forward slip and transition to side slip before touchdown.
CA.IV.M.S8 Touch down at a proper pitch attitude, within 200 feet beyond or on the specified point with no side drift and with the airplane’s longitudinal axis aligned with and over the runway centerline or landing path, as applicable.
Area of Operation IV. Takeoffs, Landings, and Go-Arounds › Task N. Go-Around/Rejected Landing
Task N. Go-Around/Rejected Landing
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-23, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with go-around/rejected landing with emphasis on factors that contribute to landing conditions that may require a go-around.
Knowledge: The applicant demonstrates understanding of:
Area of Operation IV. Takeoffs, Landings, and Go-Arounds
CA.IV.N.K1 A stabilized approach, including energy management concepts.
CA.IV.N.K2 Effects of atmospheric conditions, including wind and density altitude, on a go-around or rejected landing.
CA.IV.N.K3 Wind correction techniques on takeoff/departure and approach/landing.
CA.IV.N.K4 Go-around/rejected landing procedures, the importance of a timely decision, and appropriate airspeeds for the maneuver.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.IV.N.R1 Delayed recognition of the need for a go-around/rejected landing.
CA.IV.N.R2 Delayed performance of a go-around at low altitude.
CA.IV.N.R3 Power application.
CA.IV.N.R4 Configuring the airplane.
CA.IV.N.R5 Collision hazards.
CA.IV.N.R6 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.IV.N.R7 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.IV.N.R8 Runway incursion.
CA.IV.N.R9 Managing a go-around/rejected landing after accepting a LAHSO clearance.
Skills: The applicant exhibits the skill to:
CA.IV.N.S1 Complete the appropriate checklist(s).
CA.IV.N.S2 Make radio calls as appropriate.
CA.IV.N.S3 Make a timely decision to discontinue the approach to landing.
CA.IV.N.S4 Apply takeoff power immediately and transition to climb pitch attitude for VX or VY as appropriate ±5 knots.
CA.IV.N.S5 Configure the airplane after a positive rate of climb has been verified or in accordance with airplane manufacturer’s instructions.
CA.IV.N.S6 Maneuver to the side of the runway/landing area when necessary to clear and avoid conflicting traffic.
CA.IV.N.S7 Maintain VY ±5 knots to a safe maneuvering altitude.
CA.IV.N.S8 Maintain directional control and proper wind-drift correction throughout the climb.
CA.IV.N.S9 Use runway incursion avoidance procedures, if applicable.
Area of Operation V. › Task A. Steep Turns
Area of Operation V. Performance Maneuvers and Ground Reference Maneuvers
Area of Operation V. Performance Maneuvers and Ground Reference Maneuvers
Task A. Steep Turns
References: FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with steep turns.
Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Knowledge: The applicant demonstrates understanding of:
CA.V.A.K1 How to conduct a proper steep turn.
CA.V.A.K2 Aerodynamics associated with steep turns, including:
CA.V.A.K2a a. Maintaining coordinated flight
CA.V.A.K2b b. Overbanking tendencies
CA.V.A.K2c c. Maneuvering speed, including the impact of weight changes
CA.V.A.K2d d. Load factor and accelerated stalls
CA.V.A.K2e e. Rate and radius of turn
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.V.A.R1 Division of attention between aircraft control and orientation.
CA.V.A.R2 Collision hazards.
CA.V.A.R3 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.V.A.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.V.A.R5 Uncoordinated flight.
Skills: The applicant exhibits the skill to:
CA.V.A.S1 Clear the area.
CA.V.A.S2 Establish the manufacturer's recommended airspeed; or if one is not available, an airspeed not to exceed maneuvering speed (VA).
CA.V.A.S3 Roll into a coordinated 360° steep turn with approximately a 50° bank.
CA.V.A.S4 Perform the Task in the opposite direction.
CA.V.A.S5 Maintain the entry altitude ±100 feet, airspeed ±10 knots, bank ±5°, and roll out on the entry heading ±10°.
Area of Operation V. › Task B. Steep Spiral (ASEL, ASES)
Task B. Steep Spiral (ASEL, ASES)
References: FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with steep spirals.
Area of Operation V. Performance Maneuvers and Ground Reference Maneuvers
Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Knowledge: The applicant understands and explains:
CA.V.B.K1 Relationship to emergency landing procedures.
CA.V.B.K2 Maintaining a constant radius about a point.
CA.V.B.K3 Effects of wind on ground track and relation to a ground reference.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.V.B.R1 Division of attention between aircraft control and orientation.
CA.V.B.R2 Collision hazards.
CA.V.B.R3 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.V.B.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.V.B.R5 Uncoordinated flight.
CA.V.B.R6 Effects of wind.
CA.V.B.R7 Airframe or airspeed limitations.
Skills: The applicant exhibits the skill to:
CA.V.B.S1 Clear the area.
CA.V.B.S2 Select an altitude sufficient to continue through a series of at least three, 360° turns.
CA.V.B.S3 Establish and maintain a steep spiral, not to exceed 60° angle of bank, to maintain a constant radius about a suitable ground reference point.
CA.V.B.S4 Apply wind-drift correction to track a constant radius circle around selected reference point with bank not to exceed 60° a steepest point in turn.
CA.V.B.S5 Divide attention between airplane control, traffic avoidance and the ground track while maintaining coordinated flight.
CA.V.B.S6 Maintain the specified airspeed, ±10 knots and roll out toward an object or specified heading, ±10°, and complete the maneuver no lower than 1,500 feet above ground level (AGL).
Area of Operation V. › Task C. Chandelles (ASEL, ASES)
Task C. Chandelles (ASEL, ASES)
References: FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with chandelles.
Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Knowledge: The applicant demonstrates understanding of:
CA.V.C.K1 How to conduct proper chandelles.
Area of Operation V. Performance Maneuvers and Ground Reference Maneuvers
CA.V.C.K2 Aerodynamics associated with chandelles, including:
CA.V.C.K2a a. Maintaining coordinated flight
CA.V.C.K2b b. Overbanking tendencies
CA.V.C.K2c c. Maneuvering speed, including the impact of weight changes
CA.V.C.K2d d. Accelerated stalls
CA.V.C.K3 Appropriate airplane configuration for maximum performance climb.
CA.V.C.K4 Proper pitch control required for continuously decreasing airspeed.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.V.C.R1 Division of attention between aircraft control and orientation.
CA.V.C.R2 Collision hazards.
CA.V.C.R3 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.V.C.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.V.C.R5 Uncoordinated flight.
CA.V.C.R6 Energy management.
CA.V.C.R7 Rate and radius of turn with confined area operations.
Skills: The applicant exhibits the skill to:
CA.V.C.S1 Clear the area.
CA.V.C.S2 Select an altitude that allows the maneuver to be performed no lower than 1,500 feet above ground level (AGL).
CA.V.C.S3 Establish the appropriate entry configuration, power, and airspeed.
CA.V.C.S4 Establish the angle of bank at approximately 30°.
CA.V.C.S5 Simultaneously apply power and pitch to maintain a smooth, coordinated climbing turn, in either direction, to the 90° point, with a constant bank and continuously decreasing airspeed.
CA.V.C.S6 Begin a coordinated constant rate rollout from the 90° point to the 180° point maintaining power and a constant pitch attitude.
CA.V.C.S7 Complete rollout at the 180° point, ±10° just above a stall airspeed, and maintaining that airspeed momentarily avoiding a stall.
CA.V.C.S8 Resume a straight-and-level flight with minimum loss of altitude.
Area of Operation V. › Task D. Lazy Eights (ASEL, ASES)
Task D. Lazy Eights (ASEL, ASES)
References: FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with lazy eights.
Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information
Area of Operation V. Performance Maneuvers and Ground Reference Maneuvers
related to this Task.
Knowledge: The applicant demonstrates understanding of:
CA.V.D.K1 How to conduct proper lazy eights.
CA.V.D.K2 Aerodynamics associated with lazy eights, including how to maintain coordinated flight.
CA.V.D.K3 Performance and airspeed limitations.
CA.V.D.K4 Phases of the lazy eight maneuver from entry to recovery.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.V.D.R1 Division of attention between aircraft control and orientation.
CA.V.D.R2 Collision hazards.
CA.V.D.R3 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.V.D.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.V.D.R5 Uncoordinated flight.
CA.V.D.R6 Energy management.
CA.V.D.R7 Accelerated stalls.
Skills: The applicant exhibits the skill to:
CA.V.D.S1 Clear the area.
CA.V.D.S2 Select an altitude that allows the maneuver to be performed no lower than 1,500 feet above ground level (AGL).
CA.V.D.S3 Establish the recommended entry configuration, power, and airspeed.
CA.V.D.S4 Maintain coordinated flight throughout the maneuver.
CA.V.D.S5 Complete the maneuver in accordance with the following:
CA.V.D.S5a a. Approximately 30° bank at the steepest point
CA.V.D.S5b b. Constant change of pitch and roll rate and airspeed
CA.V.D.S5c c. Altitude at 180° point, ±100 feet from entry altitude
CA.V.D.S5d d. Airspeed at the 180° point, ±10 knots from entry airspeed
CA.V.D.S5e e. Heading at the 180° point, ±10°
CA.V.D.S6 Continue the maneuver through the number of symmetrical loops specified, then resume straight-andlevel flight.
Area of Operation V. › Task E. Eights on Pylons (ASEL, ASES)
Task E. Eights on Pylons (ASEL, ASES)
References: FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with eights on pylons.
Area of Operation V. Performance Maneuvers and Ground Reference Maneuvers
Note: See Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Knowledge: The applicant demonstrates understanding of:
CA.V.E.K1 Purpose of eights on pylons.
CA.V.E.K2 Aerodynamics associated with the eights on pylons, including coordinated and uncoordinated flight.
CA.V.E.K3 Pivotal altitude and factors that affect it.
CA.V.E.K4 Effect of wind on ground track.
CA.V.E.K5 Phases of the eights on pylons maneuver from entry to recovery.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.V.E.R1 Division of attention between aircraft control and orientation.
CA.V.E.R2 Collision hazards.
CA.V.E.R3 Low altitude maneuvering, including stall, spin, or controlled flight into terrain (CFIT).
CA.V.E.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.V.E.R5 Uncoordinated flight.
CA.V.E.R6 Energy management.
CA.V.E.R7 Emergency landing considerations.
Skills: The applicant exhibits the skill to:
CA.V.E.S1 Clear the area.
CA.V.E.S2 Determine the approximate pivotal altitude.
CA.V.E.S3 Select suitable pylons that permits straight-and-level flight between the pylons.
CA.V.E.S4 Enter the maneuver in the correct direction and position using an appropriate altitude and airspeed.
CA.V.E.S5 Establish the correct bank angle for the conditions, not to exceed 40°.
CA.V.E.S6 Apply smooth and continuous corrections so that the line-of-sight reference line remains on the pylon.
CA.V.E.S7 Divide attention between accurate, coordinated airplane control and outside visual references.
CA.V.E.S8 Maintain pylon position using appropriate pivotal altitude, avoiding slips and skids.
Area of Operation VI. Navigation › Task A. Pilotage and Dead Reckoning
Area of Operation VI. Navigation
Area of Operation VI. Navigation
Task A. Pilotage and Dead Reckoning
References: FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; VFR Navigation Charts
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with pilotage and dead reckoning.
Knowledge: The applicant demonstrates understanding of:
CA.VI.A.K1 Pilotage and dead reckoning.
CA.VI.A.K2 Magnetic compass errors.
CA.VI.A.K3 Topography.
CA.VI.A.K4 Selection of appropriate:
CA.VI.A.K4a a. Route
CA.VI.A.K4b b. Altitude(s)
CA.VI.A.K4c c. Checkpoints
CA.VI.A.K5 Plotting a course, including:
CA.VI.A.K5a a. Determining heading, speed, and course
CA.VI.A.K5b b. Wind correction angle
CA.VI.A.K5c c. Estimating time, speed, and distance
CA.VI.A.K5d d. True airspeed and density altitude
CA.VI.A.K6 Power setting selection.
CA.VI.A.K7 Planned calculations versus actual results and required corrections.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.VI.A.R1 Collision hazards.
CA.VI.A.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.VI.A.R3 Unplanned fuel/power consumption, if applicable.
Skills: The applicant exhibits the skill to:
CA.VI.A.S1 Prepare and use a flight log.
CA.VI.A.S2 Navigate by pilotage.
CA.VI.A.S3 Navigate by means of pre-computed headings, groundspeeds, elapsed time, and reference to landmarks or checkpoints.
CA.VI.A.S4 Use the magnetic direction indicator in navigation, including turns to headings.
CA.VI.A.S5 Verify position within two nautical miles of the flight-planned route.
Area of Operation VI. Navigation
CA.VI.A.S6 Arrive at the en route checkpoints within three minutes of the initial or revised estimated time of arrival (ETA) and provide a destination estimate.
CA.VI.A.S7 Maintain the selected altitude, ±100 feet and heading, ±10°.
Area of Operation VI. Navigation › Task B. Navigation Systems and Radar Services
Task B. Navigation Systems and Radar Services
References: AC 91-78; AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with navigation systems and radar services.
Note: The evaluator should reference the manufacturer’s equipment supplement(s) as necessary for appropriate limitations, procedures, etc.
Knowledge: The applicant demonstrates understanding of:
CA.VI.B.K1 Ground-based navigation (identification, orientation, course determination, equipment, tests, regulations, interference, appropriate use of navigation data, and signal integrity).
CA.VI.B.K2 Satellite-based navigation (e.g., equipment, regulations, authorized use of databases, and Receiver Autonomous Integrity Monitoring (RAIM)).
CA.VI.B.K3 Radar assistance to visual flight rules (VFR) aircraft (e.g., operations, equipment, available services, traffic advisories).
CA.VI.B.K4 Transponder (Mode(s) A, C, and S) and Automatic Dependent Surveillance-Broadcast (ADS-B).
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.VI.B.R1 Management of automated navigation and autoflight systems.
CA.VI.B.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.VI.B.R3 Limitations of the navigation system in use.
CA.VI.B.R4 Loss of a navigation signal.
CA.VI.B.R5 Use of an electronic flight bag (EFB), if used.
Skills: The applicant exhibits the skill to:
CA.VI.B.S1 Use an airborne electronic navigation system.
CA.VI.B.S2 Determine the airplane’s position using the navigation system.
CA.VI.B.S3 Intercept and track a given course, radial, or bearing.
CA.VI.B.S4 Recognize and describe the indication of station or waypoint passage.
CA.VI.B.S5 Recognize signal loss or interference and take appropriate action, if applicable.
CA.VI.B.S6 Use proper communication procedures when utilizing radar services.
CA.VI.B.S7 Maintain the appropriate altitude, ±100 feet and heading, ±10°.
Area of Operation VI. Navigation › Task C. Diversion
Task C. Diversion
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; VFR Navigation Charts
Area of Operation VI. Navigation
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with diversion.
Knowledge: The applicant demonstrates understanding of:
CA.VI.C.K1 Selecting an alternate destination.
CA.VI.C.K2 Situations that require deviations from flight plan or air traffic control (ATC) instructions.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.VI.C.R1 Collision hazards.
CA.VI.C.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.VI.C.R3 Circumstances that would make diversion prudent.
CA.VI.C.R4 Selecting an appropriate airport or seaplane base.
CA.VI.C.R5 Using available resources (e.g., automation, ATC, and flight deck planning aids).
Skills: The applicant exhibits the skill to:
CA.VI.C.S1 Select a suitable destination and route for diversion.
CA.VI.C.S2 Make a reasonable estimate of heading, groundspeed, arrival time, and fuel required to the “divert to” destination.
CA.VI.C.S3 Maintain the appropriate altitude, ±100 feet and heading, ±10°.
CA.VI.C.S4 Update/interpret weather in flight.
CA.VI.C.S5 Use displays of digital weather and aeronautical information, as applicable to maintain situational awareness.
CA.VI.C.S6 Promptly divert toward the destination.
Area of Operation VI. Navigation › Task D. Lost Procedures
Task D. Lost Procedures
References: AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; VFR Navigation Charts
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with lost procedures and can take appropriate steps to achieve a satisfactory outcome if lost.
Knowledge: The applicant demonstrates understanding of:
CA.VI.D.K1 Methods to determine position.
CA.VI.D.K2 Assistance available if lost (e.g., radar services, communication procedures).
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.VI.D.R1 Collision hazards.
CA.VI.D.R2 Distractions, task prioritization, loss of situational awareness, or disorientation.
CA.VI.D.R3 Recording times over waypoints.
Area of Operation VI. Navigation
CA.VI.D.R4 When to seek assistance or declare an emergency in a deteriorating situation.
Skills: The applicant exhibits the skill to:
CA.VI.D.S1 Use an appropriate method to determine position.
CA.VI.D.S2 Maintain an appropriate heading and climb as necessary.
CA.VI.D.S3 Identify prominent landmarks.
CA.VI.D.S4 Use navigation systems/facilities or contact an ATC facility for assistance.
CA.VI.D.S5 Select an appropriate course of action.
Area of Operation VII. Slow Flight and Stalls › Task A. Maneuvering During Slow Flight
Area of Operation VII. Slow Flight and Stalls
Area of Operation VII. Slow Flight and Stalls
Task A. Maneuvering During Slow Flight
References: FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with maneuvering during slow flight in cruise configuration.
Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Knowledge: The applicant demonstrates understanding of:
CA.VII.A.K1 Aerodynamics associated with slow flight in various airplane configurations, including the relationship between angle of attack, airspeed, load factor, power setting, airplane weight and center of gravity, airplane attitude, and yaw effects.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.VII.A.R1 Inadvertent slow flight and flight with a stall warning, which could lead to loss of control.
CA.VII.A.R2 Range and limitations of stall warning indicators (e.g., aircraft buffet, stall horn, etc.).
CA.VII.A.R3 Uncoordinated flight.
CA.VII.A.R4 Effect of environmental elements on airplane performance (e.g., turbulence, microbursts, and highdensity altitude).
CA.VII.A.R5 Collision hazards.
CA.VII.A.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
CA.VII.A.S1 Clear the area.
CA.VII.A.S2 Select an entry altitude that allows the Task to be completed no lower than 1,500 feet above ground level (AGL) (ASEL, ASES) or 3,000 feet AGL (AMEL, AMES).
CA.VII.A.S3 Establish and maintain an airspeed at which any further increase in angle of attack, increase in load factor, or reduction in power, would result in a stall warning (e.g., aircraft buffet, stall horn, etc.).
CA.VII.A.S4 Accomplish coordinated straight-and-level flight, turns, climbs, and descents with the aircraft configured as specified by the evaluator without a stall warning (e.g., aircraft buffet, stall horn, etc.).
CA.VII.A.S5 Maintain the specified altitude, ±50 feet; specified heading, ±10°; airspeed, +5/-0 knots; and specified angle of bank, ±5°.
Area of Operation VII. Slow Flight and Stalls › Task B. Power-Off Stalls
Task B. Power-Off Stalls
References: AC 61-67; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with power-off stalls.
Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Area of Operation VII. Slow Flight and Stalls
Knowledge: The applicant demonstrates understanding of:
CA.VII.B.K1 Aerodynamics associated with stalls in various airplane configurations, including the relationship between angle of attack, airspeed, load factor, power setting, airplane weight and center of gravity, airplane attitude, and yaw effects.
CA.VII.B.K2 Stall characteristics as they relate to airplane design, and recognition impending stall and full stall indications using sight, sound, or feel.
CA.VII.B.K3 Factors and situations that can lead to a power-off stall and actions that can be taken to prevent it.
CA.VII.B.K4 Fundamentals of stall recovery.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.VII.B.R1 Factors and situations that could lead to an inadvertent power-off stall, spin, and loss of control.
CA.VII.B.R2 Range and limitations of stall warning indicators (e.g., aircraft buffet, stall horn, etc.).
CA.VII.B.R3 Stall warning(s) during normal operations.
CA.VII.B.R4 Stall recovery procedure.
CA.VII.B.R5 Secondary stalls, accelerated stalls, and cross-control stalls.
CA.VII.B.R6 Effect of environmental elements on airplane performance related to power-off stalls (e.g., turbulence, microbursts, and high-density altitude).
CA.VII.B.R7 Collision hazards.
CA.VII.B.R8 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
CA.VII.B.S1 Clear the area.
CA.VII.B.S2 Select an entry altitude that allows the Task to be completed no lower than 1,500 feet above ground level (AGL) (ASEL, ASES) or 3,000 feet AGL (AMEL, AMES).
CA.VII.B.S3 Configure the airplane in the approach or landing configuration, as specified by the evaluator, and maintain coordinated flight throughout the maneuver.
CA.VII.B.S4 Establish a stabilized descent.
CA.VII.B.S5 Transition smoothly from the approach or landing attitude to a pitch attitude that induces a stall.
CA.VII.B.S6 Maintain a specified heading, ±10° if in straight flight; maintain a specified angle of bank not to exceed 20°, ±5° if in turning flight, until an impending or full stall occurs, as specified by the evaluator.
CA.VII.B.S7 Acknowledge the cues at the first indication of a stall (e.g., aircraft buffet, stall horn, etc.).
CA.VII.B.S8 Recover at the first indication of a stall or after a full stall has occurred, as specified by the evaluator.
CA.VII.B.S9 Configure the airplane as recommended by the manufacturer, and accelerate to best angle of climb speed (VX) or best rate of climb speed (VY).
CA.VII.B.S10 Return to the altitude, heading, and airspeed specified by the evaluator.
Area of Operation VII. Slow Flight and Stalls
Area of Operation VII. Slow Flight and Stalls › Task C. Power-On Stalls
Task C. Power-On Stalls
References: AC 61-67; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with power-on stalls.
Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Knowledge: The applicant demonstrates understanding of:
CA.VII.C.K1 Aerodynamics associated with stalls in various airplane configurations, including the relationship between angle of attack, airspeed, load factor, power setting, airplane weight and center of gravity, airplane attitude, and yaw effects.
CA.VII.C.K2 Stall characteristics as they relate to airplane design, and recognition impending stall and full stall indications using sight, sound, or feel.
CA.VII.C.K3 Factors and situations that can lead to a power-on stall and actions that can be taken to prevent it.
CA.VII.C.K4 Fundamentals of stall recovery.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.VII.C.R1 Factors and situations that could lead to an inadvertent power-on stall, spin, and loss of control.
CA.VII.C.R2 Range and limitations of stall warning indicators (e.g., aircraft buffet, stall horn, etc.).
CA.VII.C.R3 Stall warning(s) during normal operations.
CA.VII.C.R4 Stall recovery procedure.
CA.VII.C.R5 Secondary stalls, accelerated stalls, elevator trim stalls, and cross-control stalls.
CA.VII.C.R6 Effect of environmental elements on airplane performance related to power-on stalls (e.g., turbulence, microbursts, and high-density altitude).
CA.VII.C.R7 Collision hazards.
CA.VII.C.R8 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
CA.VII.C.S1 Clear the area.
CA.VII.C.S2 Select an entry altitude that allows the Task to be completed no lower than 1,500 feet above ground level (AGL) (ASEL, ASES) or 3,000 feet AGL (AMEL, AMES).
CA.VII.C.S3 Establish the takeoff, departure, or cruise configuration, as specified by the evaluator, and maintain coordinated flight throughout the maneuver.
CA.VII.C.S4 Set power to no less than 65 percent power.
CA.VII.C.S5 Transition smoothly from the takeoff or departure attitude to the pitch attitude that induces a stall.
CA.VII.C.S6 Maintain a specified heading ±10° if in straight flight; maintain a specified angle of bank not to exceed 20°, ±10° if in turning flight, until an impending or full stall is reached, as specified by the evaluator.
CA.VII.C.S7 Acknowledge the cues at the first indication of a stall (e.g., aircraft buffet, stall horn, etc.).
Area of Operation VII. Slow Flight and Stalls
CA.VII.C.S8 Recover at the first indication of a stall or after a full stall has occurred, as specified by the evaluator.
CA.VII.C.S9 Configure the airplane as recommended by the manufacturer, and accelerate to best angle of climb speed (VX) or best rate of climb speed (VY).
CA.VII.C.S10 Return to the altitude, heading, and airspeed specified by the evaluator.
Area of Operation VII. Slow Flight and Stalls › Task D. Accelerated Stalls
Task D. Accelerated Stalls
References: AC 61-67; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with accelerated stalls (power-on or power-off).
Note: See Appendix 2: Safety of Flight and Appendix 3: Aircraft, Equipment, and Operational Requirements & Limitations for information related to this Task.
Knowledge: The applicant demonstrates understanding of:
CA.VII.D.K1 Aerodynamics associated with accelerated stalls in various airplane configurations, including the relationship between angle of attack, airspeed, load factor, power setting, airplane weight and center of gravity, airplane attitude, and yaw effects.
CA.VII.D.K2 Stall characteristics as they relate to airplane design, and recognition impending stall and full stall indications using sight, sound, or feel.
CA.VII.D.K3 Factors leading to an accelerated stall and preventive actions.
CA.VII.D.K4 Fundamentals of stall recovery.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.VII.D.R1 Factors and situations that could lead to an inadvertent accelerated stall, spin, and loss of control.
CA.VII.D.R2 Range and limitations of stall warning indicators (e.g., aircraft buffet, stall horn, etc.).
CA.VII.D.R3 Stall warning(s) during normal operations.
CA.VII.D.R4 Stall recovery procedure.
CA.VII.D.R5 Secondary stalls, cross-control stalls, and spins.
CA.VII.D.R6 Effect of environmental elements on airplane performance related to accelerated stalls (e.g., turbulence, microbursts, and high-density altitude).
CA.VII.D.R7 Collision hazards.
CA.VII.D.R8 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
CA.VII.D.S1 Clear the area.
CA.VII.D.S2 Select an entry altitude that allows the Task to be completed no lower than 3,000 feet above ground level (AGL).
CA.VII.D.S3 Establish the configuration as specified by the evaluator.
Area of Operation VII. Slow Flight and Stalls
CA.VII.D.S4 Set power appropriate for the configuration, such that the airspeed does not exceed the maneuvering speed (VA) or any other applicable Pilot's Operating Handbook (POH)/Airplane Flight Manual (AFM) limitation.
CA.VII.D.S5 Establish and maintain a coordinated turn in a 45° bank, increasing elevator back pressure smoothly and firmly until an impending stall is reached.
CA.VII.D.S6 Acknowledge the cues at the first indication of a stall (e.g., aircraft buffet, stall horn, etc.).
CA.VII.D.S7 Execute a stall recovery in accordance with procedures set forth in the Pilot's Operating Handbook (POH)/Flight Manual (FM).
CA.VII.D.S8 Configure the airplane as recommended by the manufacturer, and accelerate to best angle of climb speed (VX) or best rate of climb speed (VY).
CA.VII.D.S9 Return to the altitude, heading, and airspeed specified by the evaluator.
Area of Operation VII. Slow Flight and Stalls › Task E. Spin Awareness
Task E. Spin Awareness
References: AC 61-67; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge of the causes and procedures for recovery from unintentional spins and understands the risk associated with unintentional spins.
Knowledge: The applicant demonstrates understanding of:
CA.VII.E.K1 Aerodynamics associated with spins in various airplane configurations, including the relationship between angle of attack, airspeed, load factor, power setting, airplane weight and center of gravity, airplane attitude, and yaw effects.
CA.VII.E.K2 What causes a spin and how to identify the entry, incipient, and developed phases of a spin.
CA.VII.E.K3 Spin recovery procedure.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.VII.E.R1 Factors and situations that could lead to inadvertent spin and loss of control.
CA.VII.E.R2 Range and limitations of stall warning indicators (e.g., aircraft buffet, stall horn, etc.).
CA.VII.E.R3 Spin recovery procedure.
CA.VII.E.R4 Effect of environmental elements on airplane performance related to spins (e.g., turbulence, microbursts, and high-density altitude).
CA.VII.E.R5 Collision hazards.
CA.VII.E.R6 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
[Intentionally left blank].
Area of Operation VIII. High-Altitude Operations › Task A. Supplemental Oxygen
Area of Operation VIII. High-Altitude Operations
Area of Operation VIII. High-Altitude Operations
Task A. Supplemental Oxygen
References: 14 CFR part 91; AC 61-107; AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with flight at higher altitudes where supplemental oxygen is required or recommended.
Knowledge: The applicant demonstrates understanding of:
CA.VIII.A.K1 Regulatory requirements for supplemental oxygen use by flight crew and passengers.
CA.VIII.A.K2 Physiological factors, including:
CA.VIII.A.K2a a. Impairment
CA.VIII.A.K2b b. Symptoms of hypoxia
CA.VIII.A.K2c c. Time of useful consciousness (TUC)
CA.VIII.A.K3 Operational factors, including:
CA.VIII.A.K3a a. Characteristics, limitations, and applicability of continuous flow, demand, and pressure-
demand oxygen systems
CA.VIII.A.K3b b. Differences between and identification of “aviator’s breathing oxygen” and other types of
oxygen
CA.VIII.A.K3c c. Precautions when using supplemental oxygen systems
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.VIII.A.R1 High altitude flight.
CA.VIII.A.R2 Use of supplemental oxygen.
CA.VIII.A.R3 Management of compressed gas containers.
CA.VIII.A.R4 Combustion hazards in an oxygen-rich environment.
Skills: The applicant exhibits the skill to:
CA.VIII.A.S1 Determine the quantity of supplemental oxygen required in a scenario given by the evaluator.
CA.VIII.A.S2 Operate or simulate operation of the installed or portable oxygen equipment in the airplane, if installed or available.
CA.VIII.A.S3 Brief passengers on use of supplemental oxygen equipment in a scenario given by the evaluator.
CA.VIII.A.S4 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation VIII. High-Altitude Operations › Task B. Pressurization
Task B. Pressurization
References: AC 61-107; AIM; FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with flight in pressurized aircraft at high altitudes.
Knowledge: The applicant demonstrates understanding of:
Area of Operation VIII. High-Altitude Operations
CA.VIII.B.K1 Fundamental concepts of aircraft pressurization system, including failure modes.
CA.VIII.B.K2 Physiological factors, including:
CA.VIII.B.K2a a. Impairment
CA.VIII.B.K2b b. Symptoms of hypoxia
CA.VIII.B.K2c c. Time of useful consciousness (TUC)
CA.VIII.B.K2d d. Effects of rapid decompression on crew and passengers
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.VIII.B.R1 High altitude flight.
CA.VIII.B.R2 Malfunction of pressurization system, if equipment is installed.
Skills: The applicant exhibits the skill to:
CA.VIII.B.S1 Operate the pressurization system, if equipment is installed.
CA.VIII.B.S2 Respond appropriately to simulated pressurization malfunctions, if equipment is installed.
CA.VIII.B.S3 Brief passengers on use of supplemental oxygen in the case of pressurization malfunction, if equipment is installed.
CA.VIII.B.S4 Use single-pilot resource management (SRM) or crew resource management (CRM), as appropriate.
Area of Operation IX. Emergency Operations › Task A. Emergency Descent
Area of Operation IX. Emergency Operations
Area of Operation IX. Emergency Operations
Task A. Emergency Descent
References: FAA-H-8083-2, FAA-H-8083-3, FAA-H-8083-25; POH/AFM
Objective: To determine the applicant exhibits satisfactory knowledge, risk management, and skills associated with emergency descent.
Note: See Appendix 2: Safety of Flight.
Knowledge: The applicant demonstrates understanding of:
CA.IX.A.K1 Situations that would require an emergency descent (e.g., depressurization, smoke, or engine fire).
CA.IX.A.K2 Immediate action items and emergency procedures.
CA.IX.A.K3 Airspeed, including airspeed limitations.
CA.IX.A.K4 Aircraft performance and limitations.
Risk Management: The applicant is able to identify, assess, and mitigate risk associated with:
CA.IX.A.R1 Altitude, wind, terrain, obstructions, gliding distance, and available landing distance considerations.
CA.IX.A.R2 Collision hazards.
CA.IX.A.R3 Configuring the airplane.
CA.IX.A.R4 Distractions, task prioritization, loss of situational awareness, or disorientation.
Skills: The applicant exhibits the skill to:
Continue reading ↓ 120 of 204 passages shown