Radar Vectors
Handbook Current 207 pages Copy saved Nov 20, 2026

FAA-H-8083-21 Gyroplane Handbook

Official source ↗ Open PDF

Text read by OCR from a scanned file (1 of 207 pages). Check the original, as some words may be misread.

FAA-H-8083-21 Rotorcraft

Flying g Handbook

U.S.Department of Transportation Federal Aviation Administration Use Only

For

ROTORCRAFT FLYING

HANDBOOK

2000

U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

Flight Standards Service

ii

ii

PREFACE The Rotorcraft Flying Handbook is designed as a technical manual for applicants who are preparing for their private, commercial, or flight instructor pilot certificates with a helicopter or gyroplane class rating. Certificated flight instructors may find this handbook a valuable training aid, since detailed coverage of aerodynamics, flight controls, systems, performance, flight maneuvers, emergencies, and aeronautical decision making is included. Topics, such as weather, navigation, radio navigation and communications, use of flight information publications, and regulations are available in other Federal Aviation Administration (FAA) publications.

FEDERAL AVIATION ADMINISTRATION

This handbook conforms to pilot training and certification concepts established by the FAA. There are different ways of teaching, as well as performing flight procedures and maneuvers, and many variations in the explanations of aerodynamic theories and principles. This handbook adopts a selective method and concept to flying helicopters and gyroplanes. The discussion and explanations reflect the most commonly used practices and principles. Occasionally, the word “must” or similar language is used where the desired action is deemed critical. The use of such language is not intended to add to, interpret, or relieve a duty imposed by Title 14 of the Code of Federal Regulations (14 CFR). This handbook is divided into two parts. The first part, chapters 1 through 14, covers helicopters, and the second part, chapters 15 through 22, covers gyroplanes. The glossary and index apply to both parts.

It is essential for persons using this handbook to also become familiar with and apply the pertinent parts of 14 CFR and the Aeronautical Information Manual (AIM). Performance standards for demonstrating competence required for pilot certification are prescribed in the appropriate rotorcraft practical test standard.

This handbook supersedes Advisory Circular (AC) 61-13B, Basic Helicopter Handbook, dated 1978. In addition, all or part of the information contained in the following advisory circulars are included in this handbook: AC 90- 87, Helicopter Dynamic Rollover; AC 90-95, Unanticipated Right Yaw in Helicopters; AC 91-32B, Safety in and around Helicopters; and AC 91-42D, Hazards of Rotating Propeller and Helicopter Rotor Blades.

This publication may be purchased from the Superintendent of Documents, U.S. Government Printing Office (GPO), Washington, DC 20402-9325, or from U.S. Government Bookstores located in major cities throughout the United States.

The current Flight Standards Service airman training and testing material and subject matter knowledge codes for all airman certificates and ratings can be obtained from the Flight Standards Services web site at http://av-info.faa.gov.

Comments regarding this handbook should be sent to U.S. Department of Transportation, Federal Aviation Administration, Airman Testing Standards Branch, AFS-630, P.O. Box 25082, Oklahoma City, OK 73125.

AC 00-2, Advisory Circular Checklist, transmits the current status of FAA advisory circulars and other flight information publications. This checklist is free of charge and may be obtained by sending a request to U.S. Department of Transportation, Subsequent Distribution Office, SVC-121.23, Ardmore East Business Center, 3341 Q 75th Avenue, Landover, MD 20785.

AC00-2 also is available on the Internet at http://www.faa.gov/abc/ac-chklst/actoc.htm.

iv

v

Chapter 4—Helicopter Flight Controls Collective Pitch Control … 4-1 Throttle Control … 4-1 Collective Pitch / Throttle Coordination … 4-2 Correlator / Governor … 4-2 Cyclic Pitch Control … 4-2 Antitorque Pedals … 4-3

Heading Control … 4-3

Chapter 5—Helicopter Systems Engines … 5-1

Chapter 5—Helicopter Systems Engines … 5-1

Reciprocating Engine … 5-1 Turbine Engine … 5-1

Compressor … 5-2 Combustion Chamber … 5-2 Turbine … 5-2 Transmission System … 5-3

Main Rotor Transmission … 5-3 Tail Rotor Drive System … 5-3 Clutch … 5-4

Centrifugal Clutch … 5-4 Belt Drive Clutch … 5-4 Freewheeling Unit … 5-4 Main Rotor System … 5-4

Fully Articulated Rotor System … 5-4 Semirigid Rotor System … 5-5 Rigid Rotor System … 5-5 Combination Rotor Systems … 5-5 Swash Plate Assembly … 5-5 Fuel Systems … 5-6

Fuel Supply System … 5-6 Engine Fuel Control System … 5-6

Reciprocating Engines … 5-7

Carburetor … 5-7 Carburetor Ice … 5-7 Fuel Injection … 5-8 Turbine Engines … 5-8 Electrical Systems … 5-8 Hydraulics … 5-9 Stability Augmentations Systems … 5-10 Autopilot … 5-10 Environmental Systems … 5-10 Anti-Icing Systems … 5-11

Chapter 6—Rotorcraft Flight Manual (Helicopter) Preliminary Pages … 6-1 General Information … 6-1 Operating Limitations … 6-1

Airspeed Limitation … 6-1 Altitude Limitations … 6-2 Rotor Limitations … 6-2

HELICOPTER

Chapter 1—Introduction to the Helicopter The Main Rotor System … 1-1

Chapter 1—Introduction to the Helicopter The Main Rotor System … 1-1

Fully Articulated Rotor System … 1-1 Semirigid Rotor System … 1-2 Rigid Rotor System … 1-2 Antitorque Systems … 1-2

Tail Rotor … 1-2 Fenestron … 1-2 NOTAR® … 1-2 Landing Gear … 1-2 Powerplant … 1-3 Flight Controls … 1-3

Chapter 2—General Aerodynamics Airfoil … 2-1

Chapter 2—General Aerodynamics Airfoil … 2-1

Relative Wind … 2-2 Blade Pitch Angle … 2-2 Angle of Attack … 2-2 Lift … 2-3

Magnus Effect … 2-3 Bernoulli’s Principle … 2-3 Newton’s Third Law of Motion … 2-4 Weight … 2-4 Thrust … 2-5 Drag … 2-5

Profile Drag … 2-5 Induced Drag … 2-5 Parasite Drag … 2-6 Total Drag … 2-6

Chapter 3—Aerodynamics of Flight Powered Flight … 3-1 Hovering Flight … 3-1

Chapter 3—Aerodynamics of Flight Powered Flight … 3-1 Hovering Flight … 3-1

Translating Tendency or Drift … 3-1 Pendular Action … 3-2 Coning … 3-2 Coriolis Effect (Law of Conservation of Angular Momentum) … 3-2 Ground Effect … 3-3 Gyroscopic Precession … 3-4 Vertical Flight … 3-4 Forward Flight … 3-5

Translational Lift … 3-5 Induced Flow … 3-6 Transverse Flow Effect … 3-6 Dissymmetry of Lift … 3-6 Sideward Flight … 3-8 Rearward Flight … 3-8 Turning Flight … 3-8 Autorotation … 3-8

Autorotation (Vertical Flight) … 3-9 Autorotation (Forward Flight) … 3-11

CONTENTS

vi

Powerplant Limitations … 6-2 Weight and Loading Distribution … 6-2 Flight Limitations … 6-3 Placards … 6-3 Emergency Procedures … 6-3 Normal Procedures … 6-3 Performance … 6-3 Weight and Balance … 6-4 Aircraft and Systems Description … 6-4 Handling, Servicing, and Maintenance … 6-4 Supplements … 6-4 Safety and Operational Tips … 6-4

Chapter 7—Weight and Balance Weight … 7-1

Chapter 7—Weight and Balance Weight … 7-1

Basic Empty Weight … 7-1 Useful Load … 7-1 Payload … 7-1 Gross Weight … 7-1 Maximum Gross Weight … 7-1 Weight Limitations … 7-1 Determining Empty Weight … 7-1 Balance … 7-2

Center of Gravity … 7-2

CG Forward of Forward Limit … 7-2 CG Aft of Aft Limit … 7-2 Lateral Balance … 7-3 Weight and Balance Calculations … 7-3

Reference Datum … 7-3 Arm … 7-4 Moment … 7-4 Center of Gravity Computation … 7-4 Weight and Balance Methods … 7-4

Computational Method … 7-4 Loading Chart Method … 7-5

Sample Problem 1 … 7-5 Sample Problem 2 … 7-5 Sample Problem 3 … 7-6 Combination Method … 7-6 Calculating Lateral CG … 7-7

Chapter 8—Performance Factors Affecting Performance … 8-1

Chapter 8—Performance Factors Affecting Performance … 8-1

Density Altitude … 8-1 Atmospheric Pressure … 8-1 Altitude … 8-2 Temperature … 8-2 Moisture (Humidity) … 8-2 High and Low Density Altitude Conditions … 8-2 Weight … 8-2 Winds … 8-2 Performance Charts … 8-3

Hovering Performance … 8-3

Sample Problem 1 … 8-4 Sample Problem 2 … 8-4

Takeoff Performance … 8-5

Sample Problem 3 … 8-5 Climb Performance … 8-5

Sample Problem 4 … 8-6

Chapter 9—Basic Flight Maneuvers Preflight … 9-1

Chapter 9—Basic Flight Maneuvers Preflight … 9-1

Minimum Equipment Lists (MELS) and Operations With Inoperative Equipment … 9-1 Engine Start and Rotor Engagement … 9-2

Rotor Safety Considerations … 9-2 Safety In and Around Helicopters … 9-3

Ramp Attendants and Aircraft Servicing Personnel … 9-3 Aircraft Servicing … 9-3 External-Load Riggers … 9-3 Pilot at the Flight Controls … 9-3 External-Load Hookup Personnel … 9-3 Passengers … 9-4 Vertical Takeoff to a Hover … 9-5

Technique … 9-5 Common Errors … 9-5 Hovering … 9-5

Technique … 9-5 Common Errors … 9-5 Hovering Turn … 9-6

Technique … 9-6 Common Errors … 9-7 Hovering—Forward Flight … 9-7

Technique … 9-7 Common Errors … 9-7 Hovering—Sideward Flight … 9-7

Technique … 9-7 Common Errors … 9-8 Hovering—Rearward Flight … 9-8

Technique … 9-8 Common Errors … 9-8 Taxiing … 9-8

Hover Taxi … 9-9 Air Taxi … 9-9

Technique … 9-9 Common Errors … 9-9 Surface Taxi … 9-9

Technique … 9-9 Common Errors … 9-10 Normal Takeoff From a Hover … 9-10

Technique … 9-10 Common Errors … 9-10 Normal Takeoff From the Surface … 9-11

Technique … 9-11 Common Errors … 9-11 Crosswind Considerations During Takeoffs … 9-11 Straight-and-Level Flight … 9-12

vii

Technique … 9-12 Common Errors … 9-12 Turns … 9-12

Technique … 9-12 Slips … 9-13 Skids … 9-13 Common Errors … 9-13 Normal Climb … 9-13

Technique … 9-13 Common Errors … 9-14 Normal Descent … 9-14

Technique … 9-14 Common Errors … 9-14 Ground Reference Maneuvers … 9-14

Rectangular Course … 9-14 S-Turns … 9-16 Turns Around a Point … 9-17 Common Errors During Ground Reference Maneuvers … 9-18 Traffic Patterns … 9-18 Approaches … 9-19

Normal Approach to a Hover … 9-19

Technique … 9-19 Common Errors … 9-19 Normal Approach to the Surface … 9-20

Technique … 9-20 Common Errors … 9-20 Crosswind During Approaches … 9-20 Go-Around … 9-20 After Landing and Securing … 9-20 Noise Abatement Procedures … 9-20

Chapter 10—Advanced Maneuvers Reconnaissance Procedures … 10-1

Chapter 10—Advanced Maneuvers Reconnaissance Procedures … 10-1

High Reconnaissance … 10-1 Low Reconnaissance … 10-1 Ground Reconnaissance … 10-1 Maximum Performance Takeoff … 10-2

Technique … 10-2 Common Errors … 10-2 Running/Rolling Takeoff … 10-2

Technique … 10-3 Common Errors … 10-3 Rapid Deceleration (Quick Stop) … 10-3

Technique … 10-3 Common Errors … 10-4 Steep Approach to a Hover … 10-4

Technique … 10-4 Common Errors … 10-5 Shallow Approach and Running/Roll-On Landing … 10-5

Technique … 10-5 Common Errors … 10-5 Slope Operations … 10-6

Slope Landing … 10-6

Technique … 10-6 Common Errors … 10-6 Slope Takeoff … 10-6

Technique … 10-7 Common Errors … 10-7 Confined Area Operations … 10-7

Approach … 10-7 Takeoff … 10-8 Common Errors … 10-8 Pinnacle and Ridgeline Operations … 10-8

Approach and Landing … 10-8 Takeoff … 10-9 Common Errors … 10-9

Chapter 11—Helicopter Emergencies Autorotation … 11-1

Chapter 11—Helicopter Emergencies Autorotation … 11-1

Straight-in Autorotation … 11-2

Technique … 11-2 Common Errors … 11-3 Power Recovery From Practice Autorotation … 11-3

Technique … 11-3 Common Errors … 11-3 Autorotation With Turns … 11-3

Technique … 11-3 Power Failure in a Hover … 11-4

Technique … 11-4 Common Errors … 11-4 Height/Velocity Diagram … 11-4

The Effect of Weight Versus Density Altitude … 11-5 Vortex Ring State (Settling With Power) … 11-5 Retreating Blade Stall … 11-6 Ground Resonance … 11-7 Dynamic Rollover … 11-7

Critical Conditions … 11-8 Cyclic Trim … 11-8 Normal Takeoffs and Landings … 11-8 Slope Takeoffs and Landings … 11-8 Use of Collective … 11-9 Precautions … 11-9 Low G Conditions and Mast Bumping … 11-10 Low Rotor RPM and Blade Stall … 11-10 Recovery From Low Rotor RPM … 11-10 Systems Malfunctions … 11-11

Antitorque System Failure … 11-11

Landing—Stuck Left Pedal … 11-11 Landing—Stuck Neutral or Right Pedal … 11-12 Unanticipated Yaw / Loss of Tail Rotor Effectiveness (LTE) … 11-12 Main Rotor Disc Interference (285-315°) … 11-12 Weathercock Stability (120-240°) … 11-13

viii

Tail Rotor Vortex Ring State (210-330°) … 11-13

LTE at Altitude … 11-13 Reducing the Onset of LTE … 11-13 Recovery Technique … 11-14 Main Drive Shaft Failure … 11-14 Hydraulic Failures … 11-14 Governor Failure … 11-14 Abnormal Vibrations … 11-14

Low Frequency Vibrations … 11-15 Medium and High Frequency Vibrations … 11-15

Tracking and Balance … 11-15 Flight Diversion … 11-15 Lost Procedures … 11-16 Emergency Equipment and Survival Gear … 11-16

Chapter 12—Attitude Instrument Flying Flight Instruments … 12-1

Chapter 12—Attitude Instrument Flying Flight Instruments … 12-1

Pitot-Static Instruments … 12-1

Airspeed Indicator … 12-1 Instrument Check … 12-1 Altimeter … 12-2

Instrument Check … 12-2 Vertical Speed Indicator … 12-2

Instrument Check … 12-2 System Errors … 12-2 Gyroscopic Instruments … 12-3

Attitude Indicator … 12-3 Heading Indicator … 12-3 Turn Indicators … 12-4 Instrument Check … 12-4 Magnetic Compass … 12-4

Compass Errors … 12-4 Magnetic Variation … 12-4

Compass Deviation … 12-5 Magnetic Dip … 12-5 Instrument Check … 12-5 Instrument Flight … 12-5

Instrument Cross-Check … 12-5 Instrument Interpretation … 12-6 Aircraft Control … 12-7 Straight-and-Level Flight … 12-7

Pitch Control … 12-7

Attitude Indicator … 12-8 Altimeter … 12-8 Vertical Speed Indicator … 12-8 Airspeed Indicator … 12-9 Bank Control … 12-9

Attitude Indicator … 12-9 Heading Indicator … 12-10 Turn Indicator … 12-10 Common Errors During Straight-and-Level Flight … 12-10

Power Control During Straight-and-Level Flight … 12-11 Common Errors During Airspeed Changes … 12-11 Straight Climbs (Constant Airspeed and Constant Rate) … 12-11

Entry … 12-12 Leveloff … 12-14 Straight Descents (Constant Airspeed and Constant Rate) … 12-14

Entry … 12-14 Leveloff … 12-15 Common Errors During Straight Climbs and Descents … 12-15 Turns … 12-15

Turns to a Predetermined Heading … 12-16 Timed Turns … 12-16

Change of Airspeed in Turns … 12-16 30° Bank Turn … 12-17 Climbing and Descending Turns … 12-17 Compass Turns … 12-17 Common Errors During Turns … 12-18 Unusual Attitudes … 12-18

Common Errors During Unusual Attitude Recoveries … 12-18 Emergencies … 12-18

Autorotations … 12-19

Common Errors During Autorotations … 12-19 Servo Failure … 12-19 Instrument Takeoff … 12-19

Common Errors During Instrument Takeoffs … 12-20

Chapter 13—Night Operations Night Flight Physiology … 13-1

Chapter 13—Night Operations Night Flight Physiology … 13-1

Vision in Flight … 13-1 The Eye … 13-1 Cones … 13-1 Rods … 13-2 Night Vision … 13-2 Night Scanning … 13-2 Aircraft Lighting … 13-3 Visual Illusions … 13-3

Autokinesis … 13-3 Night Myopia … 13-3 False Horizon … 13-3 Landing Illusions … 13-4 Night Flight … 13-4

Preflight … 13-4 Engine Starting and Rotor Engagement … 13-4 Taxi Technique … 13-4 Takeoff … 13-4 En route Procedures … 13-5

ix

Collision Avoidance at Night … 13-5 Approach and Landing … 13-5

Chapter 14—Aeronautical Decision Making Origins of ADM Training … 14-2 The Decision-Making Process … 14-3

Defining the Problem … 14-3 Choosing a Course of Action … 14-3 Implementing the Decision and Evaluating the Outcome … 14-3 Risk Management … 14-4

Assessing Risk … 14-4 Factors Affecting Decision Making … 14-5

Pilot Self-Assessment … 14-5 Recognizing Hazardous Attitudes … 14-5 Stress management … 14-6 Use of Resources … 14-6

Internal Resources … 14-7 External Resources … 14-7 Workload Management … 14-7 Situational Awareness … 14-8

Obstacles to Maintaining Situational Awareness … 14-8 Operational Pitfalls … 14-8

GYROPLANE

Chapter 15—Introduction to the Gyroplane Types of Gyroplanes … 15-1 Components … 15-2

Chapter 15—Introduction to the Gyroplane Types of Gyroplanes … 15-1 Components … 15-2

Airframe … 15-2 Powerplant … 15-2 Rotor System … 15-2 Tail Surfaces … 15-2 Landing Gear … 15-3 Wings … 15-3

Chapter 16—Aerodynamics of the Gyroplane Autorotation … 16-1

Vertical Autorotation … 16-1 Rotor Disc Regions … 16-2 Autorotation in Forward Flight … 16-2

Chapter 16—Aerodynamics of the Gyroplane Autorotation … 16-1

Reverse Flow … 16-3 Retreating Blade Stall … 16-3 Rotor Force … 16-3

Rotor Lift … 16-4 Rotor Drag … 16-4 Thrust … 16-4 Stability … 16-5

Horizontal Stabilizer … 16-5 Fuselage Drag (Center of Pressure) … 16-5 Pitch Inertia … 16-5

Propeller Thrust Line … 16-5 Rotor Force … 16-6 Trimmed Condition … 16-6

Chapter 17—Gyroplane Flight Controls Cyclic Control … 17-1 Throttle … 17-1 Rudder … 17-2 Horizontal Tail Surfaces … 17-2 Collective Control … 17-2

Chapter 18—Gyroplane Systems Propulsion Systems … 18-1 Rotor Systems … 18-1

Chapter 18—Gyroplane Systems Propulsion Systems … 18-1 Rotor Systems … 18-1

Semirigid Rotor System … 18-1 Fully Articulated Rotor System … 18-1 Prerotator … 18-2

Mechanical Prerotator … 18-2 Hydraulic Prerotator … 18-2 Electric Prerotator … 18-3 Tip Jets … 18-3 Instrumentation … 18-3

Engine Instruments … 18-3 Rotor Tachometer … 18-3 Slip/Skid Indicator … 18-4 Airspeed Indicator … 18-4 Altimeter … 18-4 IFR Flight Instrumentation … 18-4 Ground Handling … 18-4

Chapter 19—Rotorcraft Flight Manual

Chapter 19—Rotorcraft Flight Manual

(Gyroplane) Using the Flight Manual … 19-1

Weight and Balance Section … 19-1

Sample Problem … 19-1 Performance Section … 19-2

Sample Problem … 19-2 Height/Velocity Diagram … 19-3 Emergency Section … 19-3 Hang Test … 19-4

Chapter 20—Flight Operations Preflight … 20-1

Chapter 20—Flight Operations Preflight … 20-1

Cockpit Management … 20-1 Engine Starting … 20-1 Taxiing … 20-1

Blade Flap … 20-1 Before Takeoff … 20-2

Prerotation … 20-2 Takeoff … 20-3

Normal Takeoff … 20-3 Crosswind Takeoff … 20-4 Common Errors for Normal and Crosswind Takeoffs … 20-4 Short-Field Takeoff … 20-4

x

Common Errors … 20-4 High-Altitude Takeoff … 20-4 Soft-Field Takeoff … 20-5

Common Errors … 20-5 Jump Takeoff … 20-5 Basic Flight Maneuvers … 20-6

Straight-and-Level Flight … 20-6 Climbs … 20-6 Descents … 20-7 Turns … 20-7

Slips … 20-7 Skids … 20-7 Common Errors During Basic Flight Maneuvers … 20-8 Steep Turns … 20-8

Common Errors … 20-8 Ground Reference Maneuvers … 20-8

Rectangular Course … 20-8 S-Turns … 20-10 Turns Around a Point … 20-11 Common Errors During Ground Reference Maneuvers … 20-11 Flight at Slow Airspeeds … 20-12

Common Errors … 20-12 High Rate of Descent … 20-12

Common Errors … 20-13 Landings … 20-13

Normal Landing … 20-13 Short-Field Landing … 20-13 Soft-Field Landing … 20-14 Crosswind Landing … 20-14

High-Altitude Landing … 20-14 Common Errors During Landing … 20-15 Go-Around … 20-15

Common Errors … 20-15 After Landing and Securing … 20-15

Chapter 21—Gyroplane Emergencies Aborted Takeoff … 21-1

Chapter 21—Gyroplane Emergencies Aborted Takeoff … 21-1

Accelerate/Stop Distance … 21-1 Lift-off at Low Airspeed and High Angle of Attack … 21-1

Common Errors … 21-2 Pilot-Induced Oscillation (PIO) … 21-2 Buntover (Power Pushover) … 21-3 Ground Resonance … 21-3 Emergency Approach and Landing … 21-3 Emergency Equipment and Survival Gear … 21-4

Chapter 22—Gyroplane Aeronautical Decision

Chapter 22—Gyroplane Aeronautical Decision

Making Impulsivity … 22-1 Invulnerability … 22-1 Macho … 22-2 Resignation … 22-2 Anti-Authority … 22-3

Glossary … G-1

Index … I-1

Helicopters come in many sizes and shapes, but most share the same major components. These components include a cabin where the payload and crew are carried; an airframe, which houses the various components, or where components are attached; a powerplant or engine; and a transmission, which, among other things, takes the power from the engine and transmits it to the main rotor, which provides the aerodynamic forces that make the helicopter fly. Then, to keep the helicopter from turning due to torque, there must be some type of antitorque system. Finally there is the landing gear, which could be skids, wheels, skis, or floats. This chapter is an introduction to these components. [Figure 1-1]

Figure 1-1: picture of page 12Figure 1-1 · page 12
Picture of the page from the copy saved here

THE MAIN ROTOR SYSTEM The rotor system found on helicopters can consist of a single main rotor or dual rotors. With most dual rotors, the rotors turn in opposite directions so the torque from one rotor is opposed by the torque of the other. This cancels the turning tendencies. [Figure 1-2]

In general, a rotor system can be classified as either fully articulated, semirigid, or rigid. There are variations and combinations of these systems, which will be discussed in greater detail in Chapter 5—Helicopter Systems.

Figure 1-2: picture of page 12Figure 1-2 · page 12
Picture of the page from the copy saved here

FULLY ARTICULATED ROTOR SYSTEM A fully articulated rotor system usually consists of three or more rotor blades. The blades are allowed to flap, feather, and lead or lag independently of each other. Each rotor blade is attached to the rotor hub by a horizontal hinge, called the flapping hinge, which permits the blades to flap up and down. Each blade can move up and down independently of the others. The flapping hinge may be located at varying distances from the rotor hub, and there may be more than one. The position is chosen by each manufacturer, primarily with regard to stability and control.

Payload—The term used for passengers, baggage, and cargo.

Torque—In helicopters with a single, main rotor system, the tendency of the helicopter to turn in the opposite direction of the main rotor rotation.

Blade Flap—The upward or downward movement of the rotor blades during rotation.

Blade Feather or Feathering—The rotation of the blade around the spanwise (pitch change) axis.

Blade Lead or Lag—The fore and aft movement of the blade in the plane of rotation. It is sometimes called hunting or dragging.

Landing Gear

Tail Rotor

System Main Rotor

System Cabin

Airframe Transmission

Powerplant

Figure 1-2. Helicopters can have a single main rotor or a dual rotor system.

Figure 1-1. The major components of a helicopter are the cabin, airframe, landing gear, powerplant, transmission, main rotor system, and tail rotor system.

Each rotor blade is also attached to the hub by a vertical hinge, called a drag or lag hinge, that permits each blade, independently of the others, to move back and forth in the plane of the rotor disc. Dampers are normally incorporated in the design of this type of rotor system to prevent excessive motion about the drag hinge. The purpose of the drag hinge and dampers is to absorb the acceleration and deceleration of the rotor blades.

The blades of a fully articulated rotor can also be feathered, or rotated about their spanwise axis. To put it more simply, feathering means the changing of the pitch angle of the rotor blades.

SEMIRIGID ROTOR SYSTEM A semirigid rotor system allows for two different movements, flapping and feathering. This system is normally comprised of two blades, which are rigidly attached to the rotor hub. The hub is then attached to the rotor mast by a trunnion bearing or teetering hinge. This allows the blades to see-saw or flap together. As one blade flaps down, the other flaps up. Feathering is accomplished by the feathering hinge, which changes the pitch angle of the blade.

RIGID ROTOR SYSTEM The rigid rotor system is mechanically simple, but structurally complex because operating loads must be absorbed in bending rather than through hinges. In this system, the blades cannot flap or lead and lag, but they can be feathered. ANTITORQUE SYSTEMS TAIL ROTOR Most helicopters with a single, main rotor system require a separate rotor to overcome torque. This is accomplished through a variable pitch, antitorque rotor or tail rotor. [Figure 1-3]. You will need to vary the

Figure 1-3: picture of page 13Figure 1-3 · page 13
Picture of the page from the copy saved here

thrust of the antitorque system to maintain directional control whenever the main rotor torque changes, or to make heading changes while hovering.

FENESTRON Another form of antitorque rotor is the fenestron or “fan-in-tail” design. This system uses a series of rotating blades shrouded within a vertical tail. Because the blades are located within a circular duct, they are less likely to come into contact with people or objects. [Figure 1-4]

NOTAR® The NOTAR® system is an alternative to the antitorque rotor. The system uses low-pressure air that is forced into the tailboom by a fan mounted within the helicopter. The air is then fed through horizontal slots, located on the right side of the tailboom, and to a controllable rotating nozzle to provide antitorque and directional control. The low-pressure air coming from the horizontal slots, in conjunction with the downwash from the main rotor, creates a phenomenon called “Coanda Effect,” which produces a lifting force on the right side of the tailboom. [Figure 1-5]

Figure 1-4: picture of page 13Figure 1-4 · page 13
Picture of the page from the copy saved here

LANDING GEAR The most common landing gear is a skid type gear, which is suitable for landing on various types of surfaces. Some types of skid gear are equipped with dampers so touchdown shocks or jolts are not transmitted to the main rotor system. Other types absorb the shocks by the bending of the skid attachment arms. Landing skids may be fitted with replaceable heavyduty skid shoes to protect them from excessive wear and tear.

Helicopters can also be equipped with floats for water operations, or skis for landing on snow or soft terrain. Wheels are another type of landing gear. They may be in a tricycle or four point configuration. Normally, the

Tail Rotor Thrust to Compensate for Torque

Torque

Torque

Blade Rotation

Figure 1-3. The antitorque rotor produces thrust to oppose torque and helps prevent the helicopter from turning in the opposite direction of the main rotor.

Figure 1-4. Compared to an unprotected tail rotor, the fenestron antitorque system provides an improved margin of safety during ground operations.

nose or tail gear is free to swivel as the helicopter is taxied on the ground. POWERPLANT A typical small helicopter has a reciprocating engine, which is mounted on the airframe. The engine can be mounted horizontally or vertically with the transmission supplying the power to the vertical main rotor shaft. [Figure 1-6]

Another engine type is the gas turbine. This engine is used in most medium to heavy lift helicopters due to its

large horsepower output. The engine drives the main transmission, which then transfers power directly to the main rotor system, as well as the tail rotor.

Figure 1-6: picture of page 14Figure 1-6 · page 14
Picture of the page from the copy saved here

FLIGHT CONTROLS

FLIGHT CONTROLS

When you begin flying a helicopter, you will use four basic flight controls. They are the cyclic pitch control; the collective pitch control; the throttle, which is usually a twist grip control located on the end of the collective lever; and the antitorque pedals. The collective and cyclic controls the pitch of the main rotor blades. The function of these controls will be explained in detail in Chapter 4—Flight Controls. [Figure 1-7]

Figure 1-5. While in a hover, Coanda Effect supplies approximately two-thirds of the lift necessary to maintain directional control. The rest is created by directing the thrust from the controllable rotating nozzle.

Main Rotor

Wake

Rotating

Nozzle

Downwash

Air Jet

Lift

Air Intake

Main Rotor

Main Transmission

Antitorque

Rotor

Engine

Figure 1-6. Typically, the engine drives the main rotor through a transmission and belt drive or centrifugal clutch system. The antitorque rotor is driven from the transmission.

Cyclic

Throttle

Collective

Antitorque

Pedals

Figure 1-7. Location of flight controls.

Figure 1-7: picture of page 14Figure 1-7 · page 14
Picture of the page from the copy saved here

There are four forces acting on a helicopter in flight. They are lift, weight, thrust, and drag. [Figure 2-1] Lift is the upward force created by the effect of airflow as it passes around an airfoil. Weight opposes lift and is caused by the downward pull of gravity. Thrust is the force that propels the helicopter through the air. Opposing lift and thrust is drag, which is the retarding force created by development of lift and the movement of an object through the air.

AIRFOIL Before beginning the discussion of lift, you need to be aware of certain aerodynamic terms that describe an airfoil and the interaction of the airflow around it.

An airfoil is any surface, such as an airplane wing or a helicopter rotor blade, which provides aerodynamic force when it interacts with a moving stream of air. Although there are many different rotor blade airfoil designs, in most helicopter flight conditions, all airfoils perform in the same manner.

Figure 2-1: picture of page 16Figure 2-1 · page 16
Picture of the page from the copy saved here

Engineers of the first helicopters designed relatively thick airfoils for their structural characteristics. Because the rotor blades were very long and slender, it was necessary to incorporate more structural rigidity into them. This prevented excessive blade droop when the rotor system was idle, and minimized blade twisting while in flight. The airfoils were also designed to be symmetrical, which means they had the same camber (curvature) on both the upper and lower surfaces.

Symmetrical blades are very stable, which helps keep blade twisting and flight control loads to a minimum. [Figure 2-2] This stability is achieved by keeping the center of pressure virtually unchanged as the angle of attack changes. Center of pressure is the imaginary point on the chord line where the resultant of all aerodynamic forces are considered to be concentrated.

Figure 2-2: picture of page 16Figure 2-2 · page 16
Picture of the page from the copy saved here

Today, designers use thinner airfoils and obtain the required rigidity by using composite materials. In addition, airfoils are asymmetrical in design, meaning the upper and lower surface do not have the same camber. Normally these airfoils would not be as stable, but this can be corrected by bending the trailing edge to produce the same characteristics as symmetrical airfoils. This is called “reflexing.” Using this type of rotor blade allows the rotor system to operate at higher forward speeds.

One of the reasons an asymmetrical rotor blade is not as stable is that the center of pressure changes with changes in angle of attack. When the center of pressure lifting force is behind the pivot point on a rotor blade, it tends to cause the rotor disc to pitch up. As the angle of attack increases, the center of pressure moves forward. If it moves ahead of the pivot point, the pitch of the rotor disc decreases. Since the angle of attack of the rotor blades is constantly changing during each cycle of rotation, the blades tend to flap, feather, lead, and lag to a greater degree.

When referring to an airfoil, the span is the distance from the rotor hub to the blade tip. Blade twist refers to a changing chord line from the blade root to the tip.

Figure 2-2. The upper and lower curvatures are the same on a symmetrical airfoil and vary on an asymmetrical airfoil.

Asymmetrical

Symmetrical

Lift

Weight

Drag

Thrust

Figure 2-1. Four forces acting on a helicopter in forward flight.

Twisting a rotor blade causes it to produce a more even amount of lift along its span. This is necessary because rotational velocity increases toward the blade tip. The leading edge is the first part of the airfoil to meet the oncoming air. [Figure 2-3] The trailing edge is the aft portion where the airflow over the upper surface joins the airflow under the lower surface. The chord line is an imaginary straight line drawn from the leading to the trailing edge. The camber is the curvature of the airfoil’s upper and lower surfaces. The relative wind is the wind moving past the airfoil. The direction of this wind is relative to the attitude, or position, of the airfoil and is always parallel, equal, and opposite in direction to the flight path of the airfoil. The angle of attack is the angle between the blade chord line and the direction of the relative wind.

Figure 2-3: picture of page 17Figure 2-3 · page 17
Picture of the page from the copy saved here

RELATIVE WIND Relative wind is created by the motion of an airfoil through the air, by the motion of air past an airfoil, or by a combination of the two. Relative wind may be affected by several factors, including the rotation of the rotor blades, horizontal movement of the helicopter, flapping of the rotor blades, and wind speed and direction.

For a helicopter, the relative wind is the flow of air with respect to the rotor blades. If the rotor is stopped, wind blowing over the blades creates a relative wind. When the helicopter is hovering in a no-wind condition, relative wind is created by the motion of the rotor blades through the air. If the helicopter is hovering in a wind, the relative wind is a combination of the wind and the motion of the rotor blades through the air. When the helicopter is in forward flight, the relative wind is a combination of the rotation of the rotor blades and the forward speed of the helicopter.

BLADE PITCH ANGLE The pitch angle of a rotor blade is the angle between its chord line and the reference plane containing the rotor hub. [Figure 2-4] You control the pitch angle of the blades with the flight controls. The collective pitch changes each rotor blade an equal amount of pitch no matter where it is located in the plane of rotation (rotor disc) and is used to change rotor thrust. The cyclic pitch control changes the pitch of each blade as a function of where it is in the plane of rotation. This allows for trimming the helicopter in pitch and roll during forward flight and for maneuvering in all flight conditions.

Figure 2-4: picture of page 17Figure 2-4 · page 17
Picture of the page from the copy saved here

ANGLE OF ATTACK When the angle of attack is increased, air flowing over the airfoil is diverted over a greater distance, resulting in an increase of air velocity and more lift. As angle of attack is increased further, it becomes more difficult for air to flow smoothly across the top of the airfoil. At this point the airflow begins to separate from the airfoil and enters a burbling or turbulent pattern. The turbulence results in a large increase in drag and loss of lift in the area where it is taking place. Increasing the angle of attack increases lift until the critical angle of attack is reached. Any increase in the angle of attack beyond this point produces a stall and a rapid decrease in lift. [Figure 2-5]

Angle of attack should not be confused with pitch angle. Pitch angle is determined by the direction of the relative wind. You can, however, change the angle of attack by changing the pitch angle through the use of the flight controls. If the pitch angle is increased, the angle of attack is increased, if the pitch angle is reduced, the angle of attack is reduced. [Figure 2-6]

Figure 2-5: picture of page 18Figure 2-5 · page 18
Picture of the page from the copy saved here

Axis-of-Rotation—The imaginary line about which the rotor rotates. It is represented by a line drawn through the center of, and perpendicular to, the tip-path plane.

Tip-Path Plane—The imaginary circular plane outlined by the rotor blade tips as they make a cycle of rotation.

Aircraft Pitch—When referenced to a helicopter, is the movement of the helicopter about its lateral, or side to side axis. Movement of the cyclic forward or aft causes the nose of the helicopter to move up or down.

Aircraft Roll—Is the movement of the helicopter about its longitudinal, or nose to tail axis. Movement of the cyclic right or left causes the helicopter to tilt in that direction.

Figure 2-3. Aerodynamic terms of an airfoil.

Trailing

Edge

Chord Line

Angle of

Attack

FLIGHT PATH

FLIGHT PATH

RELATIVE WIND

Upper Camber

Lower Camber

Leading

Edge

Axis of Rotation

Reference Plane

Pitch Angle

Chord Line

Figure 2-4. Do not confuse the axis of rotation with the rotor mast. The only time they coincide is when the tip-path plane is perpendicular to the rotor mast.

RELATIVE WIND

LIFT MAGNUS EFFECT The explanation of lift can best be explained by looking at a cylinder rotating in an airstream. The local velocity near the cylinder is composed of the airstream velocity and the cylinder’s rotational velocity, which decreases with distance from the cylinder. On a cylinder, which is rotating in such a way that the top surface area is rotating in the same direction as the airflow, the local velocity at the surface is high on top and low on the bottom.

As shown in figure 2-7, at point “A,” a stagnation point exists where the airstream line that impinges on the surface splits; some air goes over and some under. Another stagnation point exists at “B,” where the two air streams rejoin and resume at identical velocities. We

now have upwash ahead of the rotating cylinder and downwash at the rear.

The difference in surface velocity accounts for a difference in pressure, with the pressure being lower on the top than the bottom. This low pressure area produces an upward force known as the “Magnus Effect.” This mechanically induced circulation illustrates the relationship between circulation and lift.

An airfoil with a positive angle of attack develops air circulation as its sharp trailing edge forces the rear stagnation point to be aft of the trailing edge, while the front stagnation point is below the leading edge. [Figure 2-8]

BERNOULLI’S PRINCIPLE Air flowing over the top surface accelerates. The airfoil is now subjected to Bernoulli’s Principle or the “venturi effect.” As air velocity increases through the constricted portion of a venturi tube, the pressure decreases.

Axis of Rotation

Reference Plane

Pitch Angle

Chord Line

Angle of

Attack

RELATIVE WIND

Figure 2-6. Angle of attack may be greater than, less than, or the same as the pitch angle.

Figure 2-8: picture of page 18Figure 2-8 · page 18
Picture of the page from the copy saved here

Figure 2-5. As the angle of attack is increased, the separation point starts near the trailing edge of the airfoil and progresses forward. Finally, the airfoil loses its lift and a stall condition occurs.

LIFT

STALL

8°

12-16° Figure 2-7. Magnus Effect is a lifting force produced when a rotating cylinder produces a pressure differential. This is the same effect that makes a baseball curve or a golf ball slice.

B A

Increased Local Velocity (Decreased pressure)

Decreased Local Velocity

Downwash Upwash

Figure 2-8. Air circulation around an airfoil occurs when the front stagnation point is below the leading edge and the aft stagnation point is beyond the trailing edge.

Leading Edge Stagnation Point

Trailing Edge Stagnation Point

B

A

Steady-State Flight—A condition when an aircraft is in straightand-level, unaccelerated flight, and all forces are in balance.

ward. According to Newton’s Third Law of Motion, “for every action there is an equal and opposite reaction,” the air that is deflected downward also produces an upward (lifting) reaction.

Figure 2-7: picture of page 18Figure 2-7 · page 18
Picture of the page from the copy saved here

Since air is much like water, the explanation for this source of lift may be compared to the planing effect of skis on water. The lift which supports the water skis (and the skier) is the force caused by the impact pressure and the deflection of water from the lower surfaces of the skis.

Under most flying conditions, the impact pressure and the deflection of air from the lower surface of the rotor blade provides a comparatively small percentage of the total lift. The majority of lift is the result of decreased pressure above the blade, rather than the increased pressure below it.

WEIGHT Normally, weight is thought of as being a known, fixed value, such as the weight of the helicopter, fuel, and occupants. To lift the helicopter off the ground vertically, the rotor system must generate enough lift to overcome or offset the total weight of the helicopter and its occupants. This is accomplished by increasing the pitch angle of the main rotor blades.

The weight of the helicopter can also be influenced by aerodynamic loads. When you bank a helicopter while maintaining a constant altitude, the “G” load or load factor increases. Load factor is the ratio of the load supported by the main rotor system to the actual weight of the helicopter and its contents. In steady-state flight, the helicopter has a load factor of one, which means the main rotor system is supporting the actual total weight of the helicopter. If you increase the bank angle to 60°, while still maintaining a constant altitude, the load factor increases to two. In this case, the main rotor system has to support twice the weight of the helicopter and its contents. [Figure 2-11]

Figure 2-11: picture of page 20Figure 2-11 · page 20
Picture of the page from the copy saved here

Disc loading of a helicopter is the ratio of weight to the total main rotor disc area, and is determined by dividing the total helicopter weight by the rotor disc area, which is the area swept by the blades of a rotor. Disc area can be found by using the span of one rotor blade as the radius of a circle and then determining the area the blades encompass during a complete rotation. As the helicopter is maneuvered, disc loading changes. The higher the loading, the more power you need to maintain rotor speed.

Leading Edge Stagnation Point

B

A

Compare the upper surface of an airfoil with the constriction in a venturi tube that is narrower in the middle than at the ends. [Figure 2-9]

Figure 2-9: picture of page 19Figure 2-9 · page 19
Picture of the page from the copy saved here

The upper half of the venturi tube can be replaced by layers of undisturbed air. Thus, as air flows over the upper surface of an airfoil, the camber of the airfoil causes an increase in the speed of the airflow. The increased speed of airflow results in a decrease in pressure on the upper surface of the airfoil. At the same time, air flows along the lower surface of the airfoil, building up pressure. The combination of decreased pressure on the upper surface and increased pressure on the lower surface results in an upward force. [Figure 2-10]

As angle of attack is increased, the production of lift is increased. More upwash is created ahead of the airfoil as the leading edge stagnation point moves under the leading edge, and more downwash is created aft of the trailing edge. Total lift now being produced is perpendicular to relative wind. In summary, the production of lift is based upon the airfoil creating circulation in the airstream (Magnus Effect) and creating differential pressure on the airfoil (Bernoulli’s Principle).

Figure 2-10: picture of page 19Figure 2-10 · page 19
Picture of the page from the copy saved here

NEWTON’S THIRD LAW OF MOTION Additional lift is provided by the rotor blade’s lower surface as air striking the underside is deflected down-

Figure 2-10. Lift is produced when there is decreased pressure above and increased pressure below an airfoil.

Lift Decreased Pressure

Increased Pressure

Increased Velocity Decreased Pressure

Figure 2-9. The upper surface of an airfoil is similar to the constriction in a venturi tube.

DRAG The force that resists the movement of a helicopter through the air and is produced when lift is developed is called drag. Drag always acts parallel to the relative wind. Total drag is composed of three types of drag: profile, induced, and parasite.

PROFILE DRAG Profile drag develops from the frictional resistance of the blades passing through the air. It does not change significantly with the airfoil’s angle of attack, but increases moderately when airspeed increases. Profile drag is composed of form drag and skin friction.

Form drag results from the turbulent wake caused by the separation of airflow from the surface of a structure. The amount of drag is related to both the size and shape of the structure that protrudes into the relative wind. [Figure 2-12]

Skin friction is caused by surface roughness. Even though the surface appears smooth, it may be quite rough when viewed under a microscope. A thin layer of air clings to the rough surface and creates small eddies that contribute to drag.

INDUCED DRAG Induced drag is generated by the airflow circulation around the rotor blade as it creates lift. The high-pressure area beneath the blade joins the low-pressure air above the blade at the trailing edge and at the rotor tips. This causes a spiral, or vortex, which trails behind each blade whenever lift is being produced. These vortices deflect the airstream downward in the vicinity of the blade, creating an increase in downwash. Therefore, the blade operates in an average relative wind that is inclined downward and rearward near the blade. Because the lift produced by the blade is perpendicular

Figure 2-12: picture of page 20Figure 2-12 · page 20
Picture of the page from the copy saved here

Aircraft Yaw—The movement of the helicopter about its vertical axis.

THRUST Thrust, like lift, is generated by the rotation of the main rotor system. In a helicopter, thrust can be forward, rearward, sideward, or vertical. The resultant of lift and thrust determines the direction of movement of the helicopter.

The solidity ratio is the ratio of the total rotor blade area, which is the combined area of all the main rotor blades, to the total rotor disc area. This ratio provides a means to measure the potential for a rotor system to provide thrust.

The tail rotor also produces thrust. The amount of thrust is variable through the use of the antitorque pedals and is used to control the helicopter’s yaw.

Figure 2-11. The load factor diagram allows you to calculate the amount of “G” loading exerted with various angle of bank.

Load Factor - "G's"

Bank Angle (in Degrees) 0 10 20 30 40 50 60 70 80 90

7

6

5

4

3

2

1

0

Figure 2-12. It is easy to visualize the creation of form drag by examining the airflow around a flat plate. Streamlining decreases form drag by reducing the airflow separation.

to the relative wind, the lift is inclined aft by the same amount. The component of lift that is acting in a rearward direction is induced drag. [Figure 2-13]

As the air pressure differential increases with an increase in angle of attack, stronger vortices form, and induced drag increases. Since the blade’s angle of attack is usually lower at higher airspeeds, and higher at low speeds, induced drag decreases as airspeed increases and increases as airspeed decreases. Induced drag is the major cause of drag at lower airspeeds.

PARASITE DRAG Parasite drag is present any time the helicopter is moving through the air. This type of drag increases with airspeed. Nonlifting components of the helicopter, such as the cabin, rotor mast, tail, and landing gear, contribute to parasite drag. Any loss of momentum by the airstream, due to such things as openings for engine cooling, creates additional parasite drag. Because of its rapid increase

Figure 2-13: picture of page 21Figure 2-13 · page 21
Picture of the page from the copy saved here

with increasing airspeed, parasite drag is the major cause of drag at higher airspeeds. Parasite drag varies with the square of the velocity. Doubling the airspeed increases the parasite drag four times.

TOTAL DRAG Total drag for a helicopter is the sum of all three drag forces. [Figure 2-14] As airspeed increases, parasite drag increases, while induced drag decreases. Profile drag remains relatively constant throughout the speed range with some increase at higher airspeeds. Combining all drag forces results in a total drag curve. The low point on the total drag curve shows the airspeed at which drag is minimized. This is the point where the lift-to-drag ratio is greatest and is referred to as L/Dmax. At this speed, the total lift capacity of the helicopter, when compared to the total drag of the helicopter, is most favorable. This is important in helicopter performance.

Figure 2-14. The total drag curve represents the combined forces of parasite, profile, and induced drag; and is plotted against airspeed.

0 25 50 75 100 125 150 Speed

Drag

Parasite Drag Profile Drag

Induced Drag

Figure 2-14: picture of page 21Figure 2-14 · page 21
Picture of the page from the copy saved here

Total Drag

Minimum Drag or L/D max

L/Dmax—The maximum ratio between total lift (L) and the total drag (D). This point provides the best glide speed. Any deviation from best glide speed increases drag and reduces the distance you can glide.

Induced Drag

Figure 2-13. The formation of induced drag is associated with the downward deflection of the airstream near the rotor blade.

Once a helicopter leaves the ground, it is acted upon by the four aerodynamic forces. In this chapter, we will examine these forces as they relate to flight maneuvers.

POWERED FLIGHT In powered flight (hovering, vertical, forward, sideward, or rearward), the total lift and thrust forces of a rotor are perpendicular to the tip-path plane or plane of rotation of the rotor.

HOVERING FLIGHT For standardization purposes, this discussion assumes a stationary hover in a no-wind condition. During hovering flight, a helicopter maintains a constant position over a selected point, usually a few feet above the ground. For a helicopter to hover, the lift and thrust produced by the rotor system act straight up and must equal the weight and drag, which act straight down. While hovering, you can change the amount of main rotor thrust to maintain the desired hovering altitude. This is done by changing the angle of attack of the main rotor blades and by varying power, as needed. In this case, thrust acts in the same vertical direction as lift. [Figure 3-1]

The weight that must be supported is the total weight of the helicopter and its occupants. If the amount of thrust is greater than the actual weight, the helicopter gains altitude; if thrust is less than weight, the helicopter loses altitude.

Figure 3-1: picture of page 22Figure 3-1 · page 22
Picture of the page from the copy saved here

The drag of a hovering helicopter is mainly induced drag incurred while the blades are producing lift. There is, however, some profile drag on the blades as they rotate through the air. Throughout the rest of this discussion, the term “drag” includes both induced and profile drag.

An important consequence of producing thrust is torque. As stated before, for every action there is an equal and opposite reaction. Therefore, as the engine turns the main rotor system in a counterclockwise direction, the helicopter fuselage turns clockwise. The amount of torque is directly related to the amount of engine power being used to turn the main rotor system. Remember, as power changes, torque changes.

To counteract this torque-induced turning tendency, an antitorque rotor or tail rotor is incorporated into most helicopter designs. You can vary the amount of thrust produced by the tail rotor in relation to the amount of torque produced by the engine. As the engine supplies more power, the tail rotor must produce more thrust. This is done through the use of antitorque pedals.

TRANSLATING TENDENCY OR DRIFT During hovering flight, a single main rotor helicopter tends to drift in the same direction as antitorque rotor thrust. This drifting tendency is called translating tendency. [Figure 3-2] Thrust

Lift

Weight

Drag

Figure 3-1. To maintain a hover at a constant altitude, enough lift and thrust must be generated to equal the weight of the helicopter and the drag produced by the rotor blades.

Blade Rotation

Torque

Torque

Drift

Tail Rotor Thrust

Figure 3-2. A tail rotor is designed to produce thrust in a direction opposite torque. The thrust produced by the tail rotor is sufficient to move the helicopter laterally.

greater the centrifugal force. This force gives the rotor blades their rigidity and, in turn, the strength to support the weight of the helicopter. The centrifugal force generated determines the maximum operating rotor r.p.m. due to structural limitations on the main rotor system.

Figure 3-2: picture of page 22Figure 3-2 · page 22
Picture of the page from the copy saved here

As a vertical takeoff is made, two major forces are acting at the same time—centrifugal force acting outward and perpendicular to the rotor mast, and lift acting upward and parallel to the mast. The result of these two forces is that the blades assume a conical path instead of remaining in the plane perpendicular to the mast. [Figure 3-4]

CORIOLIS EFFECT (LAW OF CONSERVATION OF ANGULAR MOMENTUM) Coriolis Effect, which is sometimes referred to as conservation of angular momentum, might be compared to spinning skaters. When they extend their arms, their rotation slows down because the center of mass moves farther from the axis of rotation. When their arms are retracted, the rotation speeds up because the center of mass moves closer to the axis of rotation.

When a rotor blade flaps upward, the center of mass of that blade moves closer to the axis of rotation and blade acceleration takes place in order to conserve angular momentum. Conversely, when that blade flaps downward, its center of mass moves further from the axis of

Before Takeoff

During Takeoff

Lift

Centrifugal

Force

Resultant

Figure 3-4: picture of page 23Figure 3-4 · page 23
Picture of the page from the copy saved here

Blade Angle

Figure 3-4. Rotor blade coning occurs as the rotor blades begin to lift the weight of the helicopter. In a semirigid and rigid rotor system, coning results in blade bending. In an articulated rotor system, the blades assume an upward angle through movement about the flapping hinges.

Centrifugal Force—The apparent force that an object moving along a circular path exerts on the body constraining the obect and that acts outwardy away from the center of rotation.

To counteract this drift, one or more of the following features may be used:

• The main transmission is mounted so that the rotor mast is rigged for the tip-path plane to have a builtin tilt opposite tail thrust, thus producing a small sideward thrust.

• Flight control rigging is designed so that the rotor disc is tilted slightly opposite tail rotor thrust when the cyclic is centered.

• The cyclic pitch control system is designed so that the rotor disc tilts slightly opposite tail rotor thrust when in a hover.

Counteracting translating tendency, in a helicopter with a counterclockwise main rotor system, causes the left skid to hang lower while hovering. The opposite is true for rotor systems turning clockwise when viewed from above.

PENDULAR ACTION Since the fuselage of the helicopter, with a single main rotor, is suspended from a single point and has considerable mass, it is free to oscillate either longitudinally or laterally in the same way as a pendulum. This pendular action can be exaggerated by over controlling; therefore, control movements should be smooth and not exaggerated. [Figure 3-3]

CONING In order for a helicopter to generate lift, the rotor blades must be turning. This creates a relative wind that is opposite the direction of rotor system rotation. The rotation of the rotor system creates centrifugal force (inertia), which tends to pull the blades straight outward from the main rotor hub. The faster the rotation, the

Hover

Rearward

Flight

Forward

Flight

Figure 3-3: picture of page 23Figure 3-3 · page 23
Picture of the page from the copy saved here

Figure 3-3. Because the helicopter’s body has mass and is suspended from a single point (the rotor mast head), it tends to act much like a pendulum.

rotation and blade deceleration takes place. [Figure 3-5] Keep in mind that due to coning, a rotor blade will not flap below a plane passing through the rotor hub and perpendicular to the axis of rotation. The acceleration and deceleration actions of the rotor blades are absorbed by either dampers or the blade structure itself, depending upon the design of the rotor system.

Two-bladed rotor systems are normally subject to Coriolis Effect to a much lesser degree than are articulated rotor systems since the blades are generally “underslung” with respect to the rotor hub, and the change in the distance of the center of mass from the axis of rotation is small. [Figure 3-6] The hunting action is absorbed by the blades through bending. If a two-bladed rotor system is not “underslung,” it will be

subject to Coriolis Effect comparable to that of a fully articulated system.

Figure 3-5: picture of page 24Figure 3-5 · page 24
Picture of the page from the copy saved here

GROUND EFFECT When hovering near the ground, a phenomenon known as ground effect takes place. [Figure 3-7] This effect usually occurs less than one rotor diameter above the surface. As the induced airflow through the rotor disc is reduced by the surface friction, the lift vector increases. This allows a lower rotor blade angle for the same amount of lift, which reduces induced drag. Ground effect also restricts the generation of blade tip vortices due to the downward and outward airflow making a larger portion of the blade produce lift. When the helicopter gains altitude vertically, with no forward airspeed, induced airflow is no longer restricted, and the blade tip vortices increase with the decrease in outward airflow. As a result, drag increases which means a

Axis of Rotation

Blade Flapping

Center of Mass

Figure 3-5. The tendency of a rotor blade to increase or decrease its velocity in its plane of rotation due to mass movement is known as Coriolis Effect, named for the mathematician who made studies of forces generated by radial movements of mass on a rotating disc.

Large Blade Tip Vortex

No Wind Hover

Blade Tip Vortex

Figure 3-7: picture of page 24Figure 3-7 · page 24
Picture of the page from the copy saved here

OUT OF GROUND EFFECT (OGE) IN GROUND EFFECT (IGE)

OUT OF GROUND EFFECT (OGE) IN GROUND EFFECT (IGE)

Downwash Pattern

Equidistant 360°

Figure 3-7. Air circulation patterns change when hovering out of ground effect (OGE) and when hovering in ground effect (IGE).

This elbow moves away from the mast as the rotor is tilted.

This elbow moves toward the mast as the rotor is tilted.

Mast Axis

CM CM

CM

CM

Figure 3-6. Because of the underslung rotor, the center of mass remains approximately the same distance from the mast after the rotor is tilted.

higher pitch angle, and more power is needed to move the air down through the rotor.

Ground effect is at its maximum in a no-wind condition over a firm, smooth surface. Tall grass, rough terrain, revetments, and water surfaces alter the airflow pattern, causing an increase in rotor tip vortices.

Figure 3-6: picture of page 24Figure 3-6 · page 24
Picture of the page from the copy saved here

GYROSCOPIC PRECESSION The spinning main rotor of a helicopter acts like a gyroscope. As such, it has the properties of gyroscopic action, one of which is precession. Gyroscopic precession is the resultant action or deflection of a spinning object when a force is applied to this object. This action occurs approximately 90° in the direction of rotation from the point where the force is applied. [Figure 3-8]

Figure 3-8: picture of page 25Figure 3-8 · page 25
Picture of the page from the copy saved here

Let us look at a two-bladed rotor system to see how gyroscopic precession affects the movement of the tippath plane. Moving the cyclic pitch control increases the angle of attack of one rotor blade with the result that a greater lifting force is applied at that point in the plane of rotation. This same control movement simultaneously decreases the angle of attack of the other blade the same amount, thus decreasing the lifting force applied at that point in the plane of rotation. The blade with the increased angle of attack tends to flap up; the blade with the decreased angle of attack tends to flap down. Because the rotor disk acts like a gyro, the blades reach maximum deflection at a point approximately 90° later in the plane of rotation. As shown in figure 3-9, the retreating blade angle of attack is increased and the advancing blade angle of attack is decreased resulting in a tipping forward of the tip-path plane, since maximum deflection takes place 90° later when the blades are at the rear and front, respectively.

In a rotor system using three or more blades, the movement of the cyclic pitch control changes the angle of attack of each blade an appropriate amount so that the end result is the same.

VERTICAL FLIGHT Hovering is actually an element of vertical flight. Increasing the angle of attack of the rotor blades (pitch) while their velocity remains constant generates additional vertical lift and thrust and the helicopter ascends. Decreasing the pitch causes the helicopter to descend. In a no wind condition when lift and thrust are less than weight and drag, the helicopter descends vertically. If

90°

Axis

Upward

Force Applied

Here

Reaction

Occurs

Here

New Axis

Gyro Tips Down Here

Gyro Tips

Up Here

Old Axis

Figure 3-8. Gyroscopic precession principle—when a force is applied to a spinning gyro, the maximum reaction occurs approximately 90° later in the direction of rotation.

Blade Rotation

Angle of Attack

Decreased

Maximum

Upward Deflection

Maximum Downward Deflection Angle of Attack

Increased

Figure 3-9. With a counterclockwise main rotor blade rotation, as each blade passes the 90° position on the left, the maximum increase in angle of attack occurs. As each blade passes the 90° position to the right, the maximum decrease in angle of attack occurs. Maximum deflection takes place 90° later—maximum upward deflection at the rear and maximum downward deflection at the front—and the tip-path plane tips forward.

lift and thrust are greater than weight and drag, the helicopter ascends vertically. [Figure 3-10]

FORWARD FLIGHT In or during forward flight, the tip-path plane is tilted forward, thus tilting the total lift-thrust force forward from the vertical. This resultant lift-thrust force can be resolved into two components—lift acting vertically upward and thrust acting horizontally in the direction of flight. In addition to lift and thrust, there is weight (the downward acting force) and drag (the rearward acting or retarding force of inertia and wind resistance). [Figure 3-11]

Figure 3-9: picture of page 25Figure 3-9 · page 25
Picture of the page from the copy saved here

In straight-and-level, unaccelerated forward flight, lift equals weight and thrust equals drag (straight-and-level flight is flight with a constant heading and at a constant altitude). If lift exceeds weight, the helicopter climbs; if lift is less than weight, the helicopter descends. If thrust exceeds drag, the helicopter speeds up; if thrust is less than drag, it slows down.

As the helicopter moves forward, it begins to lose altitude because of the lift that is lost as thrust is diverted forward. However, as the helicopter begins to accelerate, the rotor system becomes more efficient due to the increased airflow. The result is excess power over that which is required to hover. Continued acceleration causes an even larger increase in airflow through the rotor disc and more excess power.

TRANSLATIONAL LIFT Translational lift is present with any horizontal flow of air across the rotor. This increased flow is most noticeable when the airspeed reaches approximately 16 to 24 knots. As the helicopter accelerates through this speed, the rotor moves out of its vortices and is in relatively undisturbed air. The airflow is also now more horizontal, which reduces induced flow and drag with a corresponding increase in angle of attack and lift. The additional lift available at this speed is referred to as “effective translational lift” (ETL). [Figure 3-12]

Figure 3-12: picture of page 26Figure 3-12 · page 26
Picture of the page from the copy saved here

When a single-rotor helicopter flies through translational lift, the air flowing through the main rotor and over the tail rotor becomes less turbulent and more aerodynamically efficient. As the tail rotor efficiency improves, more thrust is produced causing the aircraft to yaw left in a counterclockwise rotor system. It will be necessary to use right torque pedal to correct for this tendency on takeoff. Also, if no corrections are made, the nose rises or pitches up, and rolls to the right. This is caused by combined effects of dissymmetry of lift and transverse flow effect, and is corrected with cyclic control.

Resultant

Resultant

Lift

Thrust

Helicopter Movement

Weight

Drag

Figure 3-11. To transition into forward flight, some of the vertical thrust must be vectored horizontally. You initiate this by forward movement of the cyclic control.

No Recirculation

of Air More Horizontal

Flow of Air

Reduced Induced Flow Increases Angle of Attack

Tail Rotor Operates in Relatively Clean Air

16 to 24 Knots

Figure 3-11: picture of page 26Figure 3-11 · page 26
Picture of the page from the copy saved here

Figure 3-12. Effective translational lift is easily recognized in actual flight by a transient induced aerodynamic vibration and increased performance of the helicopter.

Thrust

Lift

Weight

Drag

Vertical Ascent

Figure 3-10. To ascend vertically, more lift and thrust must be generated to overcome the forces of weight and the drag.

Translational lift is also present in a stationary hover if the wind speed is approximately 16 to 24 knots. In normal operations, always utilize the benefit of translational lift, especially if maximum performance is needed.

Figure 3-10: picture of page 26Figure 3-10 · page 26
Picture of the page from the copy saved here

INDUCED FLOW As the rotor blades rotate they generate what is called rotational relative wind. This airflow is characterized as flowing parallel and opposite the rotor’s plane of rotation and striking perpendicular to the rotor blade’s leading edge. This rotational relative wind is used to generate lift. As rotor blades produce lift, air is accelerated over the foil and projected downward. Anytime a helicopter is producing lift, it moves large masses of air vertically and down through the rotor system. This downwash or induced flow can significantly change the efficiency of the rotor system. Rotational relative wind combines with induced flow to form the resultant relative wind. As induced flow increases, resultant relative wind becomes less horizontal. Since angle of attack is determined by measuring the difference between the chord line and the resultant relative wind, as the resultant relative wind becomes less horizontal, angle of attack decreases. [Figure 3-13]

Figure 3-13: picture of page 27Figure 3-13 · page 27
Picture of the page from the copy saved here

TRANSVERSE FLOW EFFECT As the helicopter accelerates in forward flight, induced flow drops to near zero at the forward disc area and increases at the aft disc area. This increases the angle of attack at the front disc area causing the rotor blade to flap up, and reduces angle of attack at the aft disc area causing the rotor blade to flap down. Because the rotor acts like a gyro, maximum displacement occurs 90° in the direction of rotation. The result is a tendency for the helicopter to roll slightly to the right as it acceler-

ates through approximately 20 knots or if the headwind is approximately 20 knots.

You can recognize transverse flow effect because of increased vibrations of the helicopter at airspeeds just below effective translational lift on takeoff and after passing through effective translational lift during landing. To counteract transverse flow effect, a cyclic input needs to be made.

DISSYMMETRY OF LIFT When the helicopter moves through the air, the relative airflow through the main rotor disc is different on the advancing side than on the retreating side. The relative wind encountered by the advancing blade is increased by the forward speed of the helicopter, while the relative wind speed acting on the retreating blade is reduced by the helicopter’s forward airspeed. Therefore, as a result of the relative wind speed, the advancing blade side of the rotor disc produces more lift than the retreating blade side. This situation is defined as dissymmetry of lift. [Figure 3-14]

Figure 3-14: picture of page 28Figure 3-14 · page 28
Picture of the page from the copy saved here

If this condition was allowed to exist, a helicopter with a counterclockwise main rotor blade rotation would roll to the left because of the difference in lift. In reality, the main rotor blades flap and feather automatically to equalize lift across the rotor disc. Articulated rotor systems, usually with three or more blades, incorporate a horizontal hinge (flapping hinge) to allow the individual rotor blades to move, or flap up and down as they rotate. A semirigid rotor system (two blades) utilizes a teetering hinge, which allows the blades to flap as a unit. When one blade flaps up, the other flaps down.

Figure 3-13. A helicopter in forward flight, or hovering with a headwind or crosswind, has more molecules of air entering the aft portion of the rotor blade. Therefore, the angle of attack is less and the induced flow is greater at the rear of the rotor disc.

Resultant Relative Wind

Resultant Relative Wind

10 to 20 Knots

A

A

B

B

Induced Flow

Induced Flow

Angle of Attack Angle of Attack

Rotational Relative Wind Rotational Relative Wind

As shown in figure 3-15, as the rotor blade reaches the advancing side of the rotor disc (A), it reaches its maximum upflap velocity. When the blade flaps upward, the angle between the chord line and the resultant relative wind decreases. This decreases the angle of attack,

which reduces the amount of lift produced by the blade. At position (C) the rotor blade is now at its maximum downflapping velocity. Due to downflapping, the angle between the chord line and the resultant relative wind increases. This increases the angle of attack and thus the amount of lift produced by the blade.

The combination of blade flapping and slow relative wind acting on the retreating blade normally limits the maximum forward speed of a helicopter. At a high forward speed, the retreating blade stalls because of a high angle of attack and slow relative wind speed. This situation is called retreating blade stall and is evidenced by a nose pitch up, vibration, and a rolling tendency—usually to the left in helicopters with counterclockwise blade rotation.

You can avoid retreating blade stall by not exceeding the never-exceed speed. This speed is designated VNE and is usually indicated on a placard and marked on the airspeed indicator by a red line.

During aerodynamic flapping of the rotor blades as they compensate for dissymmetry of lift, the advancing blade

Relative Wind

Relative Wind

Direction of Flight

Advancing

Side

Blade Tip Speed Plus

Helicopter

Speed (400 KTS)

Blade Tip Speed Minus

Helicopter

Speed (200 KTS)

Retreating

Side

Forward Flight

100 KTS

Blade Rotation

Figure 3-14. The blade tip speed of this helicopter is approximately 300 knots. If the helicopter is moving forward at 100 knots, the relative wind speed on the advancing side is 400 knots. On the retreating side, it is only 200 knots. This difference in speed causes a dissymmetry of lift.

Figure 3-15. The combined upward flapping (reduced lift) of the advancing blade and downward flapping (increased lift) of the retreating blade equalizes lift across the main rotor disc counteracting dissymmetry of lift.

Direction of Rotation

Chord Line

Resultant RW

Chord Line

Figure 3-15: picture of page 28Figure 3-15 · page 28
Picture of the page from the copy saved here

Resultant RW

Chord Line

Downflap Velocity

Resultant RW

Chord Line

Resultant RW

Upflap Velocity

Angle of Attack at 9 O'Clock Position Angle of Attack at 3 O'Clock Position

Angle of Attack over

Tail

Angle of Attack over

Nose

A

B

C

D

D

A

B

C

RW = Relative Wind = Angle of Attack

VNE—The speed beyond which an aircraft should never be operated. VNE can change with altitude, density altitude, and weight.

ward. Drag now acts forward with the lift component straight up and weight straight down. [Figure 3-18]

TURNING FLIGHT In forward flight, the rotor disc is tilted forward, which also tilts the total lift-thrust force of the rotor disc forward. When the helicopter is banked, the rotor disc is tilted sideward resulting in lift being separated into two components. Lift acting upward and opposing weight is called the vertical component of lift. Lift acting horizontally and opposing inertia (centrifugal force) is the horizontal component of lift (centripetal force). [Figure 3-19]

Figure 3-18: picture of page 29Figure 3-18 · page 29
Picture of the page from the copy saved here

As the angle of bank increases, the total lift force is tilted more toward the horizontal, thus causing the rate of turn to increase because more lift is acting horizontally. Since the resultant lifting force acts more horizontally, the effect of lift acting vertically is deceased. To compensate for this decreased vertical lift, the angle of attack of the rotor blades must be increased in order to maintain altitude. The steeper the angle of bank, the greater the angle of attack of the rotor blades required to maintain altitude. Thus, with an increase in bank and a greater angle of attack, the resultant lifting force increases and the rate of turn is faster.

AUTOROTATION Autorotation is the state of flight where the main rotor system is being turned by the action of relative wind

Centripetal Force—The force opposite centrifugal force and attracts a body toward its axis of rotation.

Resultant Lift

Thrust

Drag

Resultant

Weight

Helicopter Movement

Figure 3-18. Forces acting on the helicopter during rearward flight.

achieves maximum upflapping displacement over the nose and maximum downflapping displacement over the tail. This causes the tip-path plane to tilt to the rear and is referred to as blowback. Figure 3-16 shows how the rotor disc was originally oriented with the front down following the initial cyclic input, but as airspeed is gained and flapping eliminates dissymmetry of lift, the front of the disc comes up, and the back of the disc goes down. This reorientation of the rotor disc changes the direction in which total rotor thrust acts so that the helicopter’s forward speed slows, but can be corrected with cyclic input.

SIDEWARD FLIGHT In sideward flight, the tip-path plane is tilted in the direction that flight is desired. This tilts the total lift-thrust vector sideward. In this case, the vertical or lift component is still straight up and weight straight down, but the horizontal or thrust component now acts sideward with drag acting to the opposite side. [Figure 3-17]

Figure 3-16: picture of page 29Figure 3-16 · page 29
Picture of the page from the copy saved here

REARWARD FLIGHT For rearward flight, the tip-path plane is tilted rearward, which, in turn, tilts the lift-thrust vector rear-

Helicopter Movement

Weight

Drag

Resultant

Thrust

Lift

Figure 3-17. Forces acting on the helicopter during sideward flight.

Figure 3-16. To compensate for blowback, you must move the cyclic forward. Blowback is more pronounced with higher airspeeds.

rather than engine power. It is the means by which a helicopter can be landed safely in the event of an engine failure. In this case, you are using altitude as potential energy and converting it to kinetic energy during the descent and touchdown. All helicopters must have this capability in order to be certified. Autorotation is permitted mechanically because of a freewheeling unit, which allows the main rotor to con-

tinue turning even if the engine is not running. In normal powered flight, air is drawn into the main rotor system from above and exhausted downward. During autorotation, airflow enters the rotor disc from below as the helicopter descends. [Figure 3-20]

Figure 3-17: picture of page 29Figure 3-17 · page 29
Picture of the page from the copy saved here

AUTOROTATION (VERTICAL FLIGHT) Most autorotations are performed with forward speed. For simplicity, the following aerodynamic explanation is based on a vertical autorotative descent (no forward speed) in still air. Under these conditions, the forces that cause the blades to turn are similar for all blades regardless of their position in the plane of rotation. Therefore, dissymmetry of lift resulting from helicopter airspeed is not a factor.

During vertical autorotation, the rotor disc is divided into three regions as illustrated in figure 3-21—the

Figure 3-20. During an autorotation, the upward flow of relative wind permits the main rotor blades to rotate at their normal speed. In effect, the blades are “gliding” in their rotational plane.

Figure 3-21. Blade regions in vertical autorotation descent.

Figure 3-19. The horizontal component of lift accelerates the helicopter toward the center of the turn.

Centripetal Force (Horizontal Component of Lift) Vertical Component

of Lift

Bank Angle

Resultant

Lift

Weight

Centrifugal Force (Inertia)

Normal Powered Flight Autorotation

Direction

Figure 3-20: picture of page 30Figure 3-20 · page 30
Picture of the page from the copy saved here

of Flight

Direction

of Flight

Stall Region 25%

Driven Region 30% Driving Region 45%

driven region, the driving region, and the stall region. Figure 3-22 shows four blade sections that illustrate force vectors. Part A is the driven region, B and D are points of equilibrium, part C is the driving region, and part E is the stall region. Force vectors are different in each region because rotational relative wind is slower near the blade root and increases continually toward the blade tip. Also, blade twist gives a more positive

angle of attack in the driving region than in the driven region. The combination of the inflow up through the rotor with rotational relative wind produces different combinations of aerodynamic force at every point along the blade.

The driven region, also called the propeller region, is nearest the blade tips. Normally, it consists of about 30

Figure 3-22. Force vectors in vertical autorotation descent.

B & D

Rotational Relative Wind

Lift

TAF

TAF

Total Aerodynamic Force Aft of Axis of Rotation

Total Aerodynamic Force Forward of Axis of Rotation

Figure 3-22: picture of page 31Figure 3-22 · page 31
Picture of the page from the copy saved here

Angle of Attack 2° Drag

Chord Line

Inflow Up Through Rotor

Resultant Relative Wind

Equilibrium

Drag

Inflow TAF

Angle of Attack 6°

Drag Driving Region

Inflow

Axis of Rotation

Angle of Attack 24° (Blade is Stalled)

TAF

Drag

Stall Region

Inflow

Driven Range

A

B

C

D

E

Driven Region

Drag

Point of Equilibrium

Point of Equilibrium

Driving Region

Stall Region

Drag

Autorotative Force

A

B & D

C

E

E

D

C

B

A

Lift

Lift

Lift

percent of the radius. In the driven region, part A of figure 3-22, the total aerodynamic force acts behind the axis of rotation, resulting in a overall drag force. The driven region produces some lift, but that lift is offset by drag. The overall result is a deceleration in the rotation of the blade. The size of this region varies with the blade pitch, rate of descent, and rotor r.p.m. When changing autorotative r.p.m., blade pitch, or rate of descent, the size of the driven region in relation to the other regions also changes.

There are two points of equilibrium on the blade—one between the driven region and the driving region, and one between the driving region and the stall region. At points of equilibrium, total aerodynamic force is aligned with the axis of rotation. Lift and drag are produced, but the total effect produces neither acceleration nor deceleration.

The driving region, or autorotative region, normally lies between 25 to 70 percent of the blade radius. Part C of figure 3-22 shows the driving region of the blade, which produces the forces needed to turn the blades during autorotation. Total aerodynamic force in the driving region is inclined slightly forward of the axis of rotation, producing a continual acceleration force. This inclination supplies thrust, which tends to accelerate the rotation of the blade. Driving region size varies with blade pitch setting, rate of descent, and rotor r.p.m.

By controlling the size of this region you can adjust autorotative r.p.m. For example, if the collective pitch is raised, the pitch angle increases in all regions. This causes the point of equilibrium to move inboard along the blade’s span, thus increasing the size of the driven region. The stall region also becomes larger while the driving region becomes smaller. Reducing the size of the driving region causes the acceleration force of the driving region and r.p.m. to decrease.

The inner 25 percent of the rotor blade is referred to as the stall region and operates above its maximum angle of attack (stall angle) causing drag which tends to slow

rotation of the blade. Part E of figure 3-22 depicts the stall region.

A constant rotor r.p.m. is achieved by adjusting the collective pitch so blade acceleration forces from the driving region are balanced with the deceleration forces from the driven and stall regions.

AUTOROTATION (FORWARD FLIGHT) Autorotative force in forward flight is produced in exactly the same manner as when the helicopter is descending vertically in still air. However, because forward speed changes the inflow of air up through the rotor disc, all three regions move outboard along the blade span on the retreating side of the disc where angle of attack is larger, as shown in figure 3-23. With lower angles of attack on the advancing side blade, more of that blade falls in the driven region. On the retreating side, more of the blade is in the stall region. A small section near the root experiences a reversed flow, therefore the size of the driven region on the retreating side is reduced.

Figure 3-23. Blade regions in forward autorotation descent.

Forward

Driven Region

Driving Region

Retreating

Side

Stall Region

Advancing

Side

Figure 3-23: picture of page 32Figure 3-23 · page 32
Picture of the page from the copy saved here

Note: In this chapter, it is assumed that the helicopter has a counterclockwise main rotor blade rotation as viewed from above. If flying a helicopter with a clockwise rotation, you will need to reverse left and right references, particularly in the areas of rotor blade pitch change, antitorque pedal movement, and tail rotor thrust.

There are four basic controls used during flight. They are the collective pitch control, the throttle, the cyclic pitch control, and the antitorque pedals.

COLLECTIVE PITCH CONTROL The collective pitch control, located on the left side of the pilot’s seat, changes the pitch angle of all main rotor blades simultaneously, or collectively, as the name implies. As the collective pitch control is raised, there is a simultaneous and equal increase in pitch angle of all main rotor blades; as it is lowered, there is a simultaneous and equal decrease in pitch angle. This is done through a series of mechanical linkages and the amount of movement in the collective lever determines the amount of blade pitch change. [Figure 4-1] An

Figure 4-1: picture of page 34Figure 4-1 · page 34
Picture of the page from the copy saved here

adjustable friction control helps prevent inadvertent collective pitch movement.

Changing the pitch angle on the blades changes the angle of attack on each blade. With a change in angle of attack comes a change in drag, which affects the speed or r.p.m. of the main rotor. As the pitch angle increases, angle of attack increases, drag increases, and rotor r.p.m. decreases. Decreasing pitch angle decreases both angle of attack and drag, while rotor r.p.m. increases. In order to maintain a constant rotor r.p.m., which is essential in helicopter operations, a proportionate change in power is required to compensate for the change in drag. This is accomplished with the throttle control or a correlator and/or governor, which automatically adjusts engine power.

THROTTLE CONTROL The function of the throttle is to regulate engine r.p.m. If the correlator or governor system does not maintain the desired r.p.m. when the collective is raised or lowered, or if those systems are not installed, the throttle

Figure 4-1. Raising the collective pitch control increases the pitch angle the same amount on all blades.

has to be moved manually with the twist grip in order to maintain r.p.m. Twisting the throttle outboard increases r.p.m.; twisting it inboard decreases r.p.m. [Figure 4-2]

COLLECTIVE PITCH / THROTTLE COORDINATION When the collective pitch is raised, the load on the engine is increased in order to maintain desired r.p.m. The load is measured by a manifold pressure gauge in piston helicopters or by a torque gauge in turbine helicopters.

In piston helicopters, the collective pitch is the primary control for manifold pressure, and the throttle is the primary control for r.p.m. However, the collective pitch control also influences r.p.m., and the throttle also influences manifold pressure; therefore, each is considered to be a secondary control of the other’s function. Both the tachometer (r.p.m. indicator) and the manifold pressure gauge must be analyzed to determine which control to use. Figure 4-3 illustrates this relationship.

Figure 4-2: picture of page 35Figure 4-2 · page 35
Picture of the page from the copy saved here

CORRELATOR / GOVERNOR A correlator is a mechanical connection between the collective lever and the engine throttle. When the collective lever is raised, power is automatically increased and when lowered, power is decreased. This system maintains r.p.m. close to the desired value, but still requires adjustment of the throttle for fine tuning.

A governor is a sensing device that senses rotor and engine r.p.m. and makes the necessary adjustments in order to keep rotor r.p.m. constant. In normal operations, once the rotor r.p.m. is set, the governor keeps the r.p.m. constant, and there is no need to make any throttle adjustments. Governors are common on all turbine helicopters and used on some piston powered helicopters.

Some helicopters do not have correlators or governors and require coordination of all collective and throttle movements. When the collective is raised, the throttle must be increased; when the collective is lowered, the throttle must be decreased. As with any aircraft control, large adjustments of either collective pitch or throttle should be avoided. All corrections should be made through the use of smooth pressure. CYCLIC PITCH CONTROL The cyclic pitch control tilts the main rotor disc by changing the pitch angle of the rotor blades in their cycle of rotation. When the main rotor disc is tilted, the horizontal component of lift moves the helicopter in the direction of tilt. [Figure 4-4]

Figure 4-2. A twist grip throttle is usually mounted on the end of the collective lever. Some turbine helicopters have the throttles mounted on the overhead panel or on the floor in the cockpit.

If Manifold Pressure

is

and R.P.M.

is

Solution

Low

Low

Low

Low High

High

High

High

Increasing the throttle increases manifold pressure and r.p.m.

Figure 4-4: picture of page 35Figure 4-4 · page 35
Picture of the page from the copy saved here

Lowering the collective pitch decreases manifold pressure and increases r.p.m.

Raising the collective pitch increases manifold pressure and decreases r.p.m.

Reducing the throttle decreases manifold pressure and r.p.m.

Figure 4-3. Relationship between manifold pressure, r.p.m., collective, and throttle.

Figure 4-4. The cyclic pitch control may be mounted vertically between the pilot’s knees or on a teetering bar from a single cyclic located in the center of the helicopter. The cyclic can pivot in all directions.

Figure 4-3: picture of page 35Figure 4-3 · page 35
Picture of the page from the copy saved here

The rotor disc tilts in the direction that pressure is applied to the cyclic pitch control. If the cyclic is moved forward, the rotor disc tilts forward; if the cyclic is moved aft, the disc tilts aft, and so on. Because the rotor disc acts like a gyro, the mechanical linkages for the cyclic control rods are rigged in such a way that they decrease the pitch angle of the rotor blade approximately 90° before it reaches the direction of cyclic displacement, and increase the pitch angle of the rotor blade approximately 90° after it passes the direction of displacement. An increase in pitch angle increases angle of attack; a decrease in pitch angle decreases angle of attack. For example, if the cyclic is moved forward, the angle of attack decreases as the rotor blade passes the right side of the helicopter and increases on the left side. This results in maximum downward deflection of the rotor blade in front of the helicopter and maximum upward deflection behind it, causing the rotor disc to tilt forward.

ANTITORQUE PEDALS The antitorque pedals, located on the cabin floor by the pilot’s feet, control the pitch, and therefore the thrust, of the tail rotor blades. [Figure 4-5] . The main purpose of the tail rotor is to counteract the torque effect of the main rotor. Since torque varies with changes in power, the tail rotor thrust must also be varied. The pedals are connected to the pitch change mechanism on the tail rotor gearbox and allow the pitch angle on the tail rotor blades to be increased or decreased.

HEADING CONTROL Besides counteracting torque of the main rotor, the tail rotor is also used to control the heading of the helicopter while hovering or when making hovering turns. Hovering turns are commonly referred to as “pedal turns.”

Figure 4-5: picture of page 36Figure 4-5 · page 36
Picture of the page from the copy saved here

In forward flight, the antitorque pedals are not used to control the heading of the helicopter, except during portions of crosswind takeoffs and approaches. Instead they are used to compensate for torque to put the helicopter in longitudinal trim so that coordinated flight can be maintained. The cyclic control is used to change heading by making a turn to the desired direction.

The thrust of the tail rotor depends on the pitch angle of the tail rotor blades. This pitch angle can be positive, negative, or zero. Apositive pitch angle tends to move the tail to the right. A negative pitch angle moves the tail to the left, while no thrust is produced with a zero pitch angle.

With the right pedal moved forward of the neutral position, the tail rotor either has a negative pitch angle or a small positive pitch angle. The farther it is forward, the larger the negative pitch angle. The nearer it is to neutral, the more positive the pitch angle, and somewhere in between, it has a zero pitch angle. As the left pedal is moved forward of the neutral position, the positive pitch angle of the tail rotor increases until it becomes maximum with full forward displacement of the left pedal.

If the tail rotor has a negative pitch angle, tail rotor thrust is working in the same direction as the torque of the main rotor. With a small positive pitch angle, the tail rotor does not produce sufficient thrust to overcome the torque effect of the main rotor during cruise flight. Therefore, if the right pedal is displaced forward of neutral during cruising flight, the tail rotor thrust does not overcome the torque effect, and the nose yaws to the right. [Figure 4-6]

Figure 4-6: picture of page 36Figure 4-6 · page 36
Picture of the page from the copy saved here

With the antitorque pedals in the neutral position, the tail rotor has a medium positive pitch angle. In medium positive pitch, the tail rotor thrust approximately equals the torque of the main rotor during cruise flight, so the helicopter maintains a constant heading in level flight.

Figure 4-5. Antitorque pedals compensate for changes in torque and control heading in a hover.

Tail Moves Tail Moves

Negative or Low

Positive Pitch

Medium Positive Pitch

High Positive

Pitch

Figure 4-6. Tail rotor pitch angle and thrust in relation to pedal positions during cruising flight.

If the left pedal is in a forward position, the tail rotor has a high positive pitch position. In this position, tail rotor thrust exceeds the thrust needed to overcome torque effect during cruising flight so the helicopter yaws to the left.

The above explanation is based on cruise power and airspeed. Since the amount of torque is dependent on the amount of engine power being supplied to the main rotor, the relative positions of the pedals required to counteract torque depend upon the amount of power being used at any time. In general, the less power being used, the greater the requirement for forward displacement of the

right pedal; the greater the power, the greater the forward displacement of the left pedal.

The maximum positive pitch angle of the tail rotor is generally somewhat greater than the maximum negative pitch angle available. This is because the primary purpose of the tail rotor is to counteract the torque of the main rotor. The capability for tail rotors to produce thrust to the left (negative pitch angle) is necessary, because during autorotation the drag of the transmission tends to yaw the nose to the left, or in the same direction the main rotor is turning.

By knowing the various systems on a helicopter, you will be able to more easily recognize potential problems, and if a problem arises, you will have a better understanding of what to do to correct the situation.

ENGINES The two most common types of engines used in helicopters are the reciprocating engine and the turbine engine. Reciprocating engines, also called piston engines, are generally used in smaller helicopters. Most training helicopters use reciprocating engines because they are relatively simple and inexpensive to operate. Turbine engines are more powerful and are used in a wide variety of helicopters. They produce a tremendous amount of power for their size but are generally more expensive to operate.

RECIPROCATING ENGINE The reciprocating engine consists of a series of pistons connected to a rotating crankshaft. As the pistons move up and down, the crankshaft rotates. The reciprocating engine gets its name from the back-and-forth movement of its internal parts. The four-stroke engine is the most common type, and refers to the four different cycles the engine undergoes to produce power. [Figure 5-1]

Figure 5-1: picture of page 38Figure 5-1 · page 38
Picture of the page from the copy saved here

When the piston moves away from the cylinder head on the intake stroke, the intake valve opens and a mixture of fuel and air is drawn into the combustion chamber. As the cylinder moves back towards the cylinder head, the intake valve closes, and the fuel/air mixture is compressed. When compression is nearly complete, the spark plugs fire and the compressed mixture is ignited to begin the power stroke. The rapidly expanding gases from the controlled burning of the fuel/air mixture drive the piston away from the cylinder head, thus providing power to rotate the crankshaft. The piston then moves back toward the cylinder head on the exhaust stroke where the burned gasses are expelled through the opened exhaust valve.

Even when the engine is operated at a fairly low speed, the four-stroke cycle takes place several hundred times each minute. In a four-cylinder engine, each cylinder operates on a different stroke. Continuous rotation of a crankshaft is maintained by the precise timing of the power strokes in each cylinder.

TURBINE ENGINE The gas turbine engine mounted on most helicopters is made up of a compressor, combustion chamber, turbine, and gearbox assembly. The compressor compresses the air, which is then fed into the combustion chamber where atomized fuel is injected into it. The fuel/air mixture is ignited and allowed to expand. This combustion gas is then forced through a series of turbine wheels causing them to turn. These turbine wheels provide power to both the engine compressor and the main rotor system through an output shaft. The

Figure 5-1. The arrows in this illustration indicate the direction of motion of the crankshaft and piston during the fourstroke cycle.

Intake Compression

Power Exhaust

Intake Valve

Exhaust Valve

Spark Plug

Piston

Connecting Rod

Crankshaft

1 2

3 4

combustion gas is finally expelled through an exhaust outlet. [Figure 5-2]

Figure 5-2: picture of page 39Figure 5-2 · page 39
Picture of the page from the copy saved here

COMPRESSOR The compressor may consist of an axial compressor, a centrifugal compressor, or both. An axial compressor consists of two main elements, the rotor and the stator. The rotor consists of a number of blades fixed on a rotating spindle and resembles a fan. As the rotor turns, air is drawn rearwards. Stator vanes are arranged in fixed rows between the rotor blades and act as a diffuser at each stage to decrease air velocity and increase air pressure. There may be a number of rows of rotor blades and stator vanes. Each row constitutes a pressure stage, and the number of stages depends on the amount of air and pressure rise required for the particular engine.

A centrifugal compressor consists of an impeller, diffuser, and a manifold. The impeller, which is a forged disc with integral blades, rotates at a high speed to draw air in and expel it at an accelerated rate. The air then passes through the diffuser which slows the air down. When the velocity of the air is slowed, static pressure increases, resulting in compressed, high-pressure air. The high pressure air then passes through the compressor manifold where it is distributed to the combustion chamber.

COMBUSTION CHAMBER Unlike a piston engine, the combustion in a turbine engine is continuous. An igniter plug serves only to ignite the fuel/air mixture when starting the engine. Once the fuel/air mixture is ignited, it will continue to burn as long as the fuel/air mixture continues to be present. If there is an interruption of fuel, air, or both, combustion ceases. This is known as a “flame-out,” and the engine has to be restarted or re-lit. Some helicopters are equipped with auto-relight, which automatically activates the igniters to start combustion if the engine flames out.

TURBINE The turbine section consists of a series of turbine wheels that are used to drive the compressor section and the rotor system. The first stage, which is usually referred to as the gas producer or N1 may consist of one or more turbine wheels. This stage drives the components necessary to complete the turbine cycle making the engine self-sustaining. Common components driven by the N1 stage are the compressor, oil pump, and fuel pump. The second stage, which may also consist of one or more wheels, is dedicated to driving the main rotor system and accessories from the engine gearbox. This is referred to as the power turbine (N2 or Nr).

Compressor Discharge Air Tube

Exhaust Air Outlet

Igniter Plug

Fuel Nozzle

Air

Inlet

Output Shaft

Gear

Compressor Rotor Turbine to Compressor Coupling Combustion

Liner

N2

N1

Inlet Air Compressor Discharge Air Combustion Gasses Exhaust Gasses

Compression Section Gearbox Section Turbine Section Combustion Section

Stator

Rotor

Figure 5-2. Many helicopters use a turboshaft engine to drive the main transmission and rotor systems. The main difference between a turboshaft and a turbojet engine is that most of the energy produced by the expanding gases is used to drive a turbine rather than producing thrust through the expulsion of exhaust gases.

If the first and second stage turbines are mechanically coupled to each other, the system is said to be a direct-drive engine or fixed turbine. These engines share a common shaft, which means the first and second stage turbines, and thus the compressor and output shaft, are connected.

On most turbine assemblies used in helicopters, the first stage and second stage turbines are not mechanically connected to each other. Rather, they are mounted on independent shafts and can turn freely with respect to each other. This is referred to as a “free turbine.” When the engine is running, the combustion gases pass through the first stage turbine to drive the compressor rotor, and then past the independent second stage turbine, which turns the gearbox to drive the output shaft.

TRANSMISSION SYSTEM The transmission system transfers power from the engine to the main rotor, tail rotor, and other accessories. The main components of the transmission system are the main rotor transmission, tail rotor drive system, clutch, and freewheeling unit. Helicopter transmissions are normally lubricated and cooled with their own oil supply. A sight gauge is provided to check the oil level. Some transmissions have chip detectors located in the sump. These detectors are wired to warning lights located on the pilot’s instrument panel that illuminate in the event of an internal problem.

MAIN ROTOR TRANSMISSION The primary purpose of the main rotor transmission is to reduce engine output r.p.m. to optimum rotor r.p.m. This reduction is different for the various helicopters, but as an example, suppose the engine r.p.m. of a specific helicopter is 2,700. To achieve a rotor speed of 450 r.p.m. would require a 6 to 1 reduction. A 9 to 1 reduction would mean the rotor would turn at 300 r.p.m.

Most helicopters use a dual-needle tachometer to show both engine and rotor r.p.m. or a percentage of engine and rotor r.p.m. The rotor r.p.m. needle normally is used only during clutch engagement to monitor rotor acceleration, and in autorotation to maintain r.p.m. within prescribed limits. [Figure 5-3]

Chip Detector—A chip detector is a warning device that alerts you to any abnormal wear in a transmission or engine. It consists of a magnetic plug located within the transmission. The magnet attracts any ferrous metal particles that have come loose from the bearings or other transmission parts. Most chip detectors send a signal to lights located on the instrument panel that illuminate when ferrous metal particles are picked up.

In helicopters with horizontally mounted engines, another purpose of the main rotor transmission is to change the axis of rotation from the horizontal axis of the engine to the vertical axis of the rotor shaft.

Figure 5-3: picture of page 40Figure 5-3 · page 40
Picture of the page from the copy saved here

TAIL ROTOR DRIVE SYSTEM The tail rotor drive system consists of a tail rotor drive shaft powered from the main transmission and a tail rotor transmission mounted at the end of the tail boom. The drive shaft may consist of one long shaft or a series of shorter shafts connected at both ends with flexible couplings. This allows the drive shaft to flex with the tail boom. The tail rotor transmission provides a right angle drive for the tail rotor and may also include gearing to adjust the output to optimum tail rotor r.p.m. [Figure 5-4]

Figure 5-3. There are various types of dual-needle tachometers, however, when the needles are superimposed or married, the ratio of the engine r.p.m. is the same as the gear reduction ratio.

Figure 5-4. The typical components of a tail rotor drive system are shown here.

Tail Rotor Transmission

Tail Rotor

Drive Shaft

Main Transmission

Figure 5-4: picture of page 40Figure 5-4 · page 40
Picture of the page from the copy saved here

CLUTCH In a conventional airplane, the engine and propeller are permanently connected. However, in a helicopter there is a different relationship between the engine and the rotor. Because of the greater weight of a rotor in relation to the power of the engine, as compared to the weight of a propeller and the power in an airplane, the rotor must be disconnected from the engine when you engage the starter. A clutch allows the engine to be started and then gradually pick up the load of the rotor.

On free turbine engines, no clutch is required, as the gas producer turbine is essentially disconnected from the power turbine. When the engine is started, there is little resistance from the power turbine. This enables the gas producer turbine to accelerate to normal idle speed without the load of the transmission and rotor system dragging it down. As the gas pressure increases through the power turbine, the rotor blades begin to turn, slowly at first and then gradually accelerate to normal operating r.p.m.

On reciprocating helicopters, the two main types of clutches are the centrifugal clutch and the belt drive clutch.

CENTRIFUGAL CLUTCH The centrifugal clutch is made up of an inner assembly and a outer drum. The inner assembly, which is connected to the engine driveshaft, consists of shoes lined with material similar to automotive brake linings. At low engine speeds, springs hold the shoes in, so there is no contact with the outer drum, which is attached to the transmission input shaft. As engine speed increases, centrifugal force causes the clutch shoes to move outward and begin sliding against the outer drum. The transmission input shaft begins to rotate, causing the rotor to turn, slowly at first, but increasing as the friction increases between the clutch shoes and transmission drum. As rotor speed increases, the rotor tachometer needle shows an increase by moving toward the engine tachometer needle. When the two needles are superimposed, the engine and the rotor are synchronized, indicating the clutch is fully engaged and there is no further slippage of the clutch shoes.

BELT DRIVE CLUTCH Some helicopters utilize a belt drive to transmit power from the engine to the transmission. A belt drive consists of a lower pulley attached to the engine, an upper pulley attached to the transmission input shaft, a belt or a series of V-belts, and some means of applying tension to the belts. The belts fit loosely over the upper and lower pulley when there is no tension on the belts. This allows the engine to be started without any load from the transmission. Once the engine is running, tension on the belts is gradually increased. When the rotor and engine tachometer needles are superimposed, the rotor and the engine are synchronized, and the clutch is then fully engaged.

Advantages of this system include vibration isolation, simple maintenance, and the ability to start and warm up the engine without engaging the rotor.

FREEWHEELING UNIT Since lift in a helicopter is provided by rotating airfoils, these airfoils must be free to rotate if the engine fails. The freewheeling unit automatically disengages the engine from the main rotor when engine r.p.m. is less than main rotor r.p.m. This allows the main rotor to continue turning at normal in-flight speeds. The most common freewheeling unit assembly consists of a one-way sprag clutch located between the engine and main rotor transmission. This is usually in the upper pulley in a piston helicopter or mounted on the engine gearbox in a turbine helicopter. When the engine is driving the rotor, inclined surfaces in the spray clutch force rollers against an outer drum. This prevents the engine from exceeding transmission r.p.m. If the engine fails, the rollers move inward, allowing the outer drum to exceed the speed of the inner portion. The transmission can then exceed the speed of the engine. In this condition, engine speed is less than that of the drive system, and the helicopter is in an autorotative state.

MAIN ROTOR SYSTEM Main rotor systems are classified according to how the main rotor blades move relative to the main rotor hub. As was described in Chapter 1—Introduction to the Helicopter, there are three basic classifications: fully articulated, semirigid, or rigid. Some modern rotor systems use a combination of these types.

FULLY ARTICULATED ROTOR SYSTEM In a fully articulated rotor system, each rotor blade is attached to the rotor hub through a series of hinges, which allow the blade to move independently of the others. These rotor systems usually have three or more blades. [Figure 5-5]

Pitch Change

Axis (Feathering)

Flapping

Hinge

Damper

Drag Hinge

Pitch Horn

Figure 5-5. Each blade of a fully articulated rotor system can flap, drag, and feather independently of the other blades.

The horizontal hinge, called the flapping hinge, allows the blade to move up and down. This movement is called flapping and is designed to compensate for dissymetry of lift. The flapping hinge may be located at varying distances from the rotor hub, and there may be more than one hinge.

Figure 5-5: picture of page 41Figure 5-5 · page 41
Picture of the page from the copy saved here

The vertical hinge, called the lead-lag or drag hinge, allows the blade to move back and forth. This movement is called lead-lag, dragging, or hunting. Dampers are usually used to prevent excess back and forth movement around the drag hinge. The purpose of the drag hinge and dampers is to compensate for the acceleration and deceleration caused by Coriolis Effect.

Each blade can also be feathered, that is, rotated around its spanwise axis. Feathering the blade means changing the pitch angle of the blade. By changing the pitch angle of the blades you can control the thrust and direction of the main rotor disc.

SEMIRIGID ROTOR SYSTEM A semirigid rotor system is usually composed of two blades which are rigidly mounted to the main rotor hub. The main rotor hub is free to tilt with respect to the main rotor shaft on what is known as a teetering hinge. This allows the blades to flap together as a unit. As one blade flaps up, the other flaps down. Since there is no vertical drag hinge, lead-lag forces are absorbed through blade bending. [Figure 5-6]

Figure 5-6: picture of page 42Figure 5-6 · page 42
Picture of the page from the copy saved here

RIGID ROTOR SYSTEM In a rigid rotor system, the blades, hub, and mast are rigid with respect to each other. There are no vertical or horizontal hinges so the blades cannot flap or drag, but

they can be feathered. Flapping and lead/lag forces are absorbed by blade bending.

COMBINATION ROTOR SYSTEMS Modern rotor systems may use the combined principles of the rotor systems mentioned above. Some rotor hubs incorporate a flexible hub, which allows for blade bending (flexing) without the need for bearings or hinges. These systems, called flextures, are usually constructed from composite material. Elastomeric bearings may also be used in place of conventional roller bearings. Elastomeric bearings are bearings constructed from a rubber type material and have limited movement that is perfectly suited for helicopter applications. Flextures and elastomeric bearings require no lubrication and, therefore, require less maintenance. They also absorb vibration, which means less fatigue and longer service life for the helicopter components. [Figure 5-7]

Figure 5-7: picture of page 42Figure 5-7 · page 42
Picture of the page from the copy saved here

SWASH PLATE ASSEMBLY The purpose of the swash plate is to transmit control inputs from the collective and cyclic controls to the main rotor blades. It consists of two main parts: the stationary

Teetering

Hinge

Feathering Hinge

Static Stops

Pitch Horn

Figure 5-6. On a semirigid rotor system, a teetering hinge allows the rotor hub and blades to flap as a unit. A static flapping stop located above the hub prevents excess rocking when the blades are stopped. As the blades begin to turn, centrifugal force pulls the static stops out of the way.

Figure 5-7. Rotor systems, such as Eurocopter’s Starflex or Bell’s soft-in-plane, use composite material and elastomeric bearings to reduce complexity and maintenance and, thereby, increase reliability.

Continue reading ↓ 120 of 798 passages shown