Radar Vectors
Advisory Circular Cancelled Issued Dec 31, 2007 AFS-800 77 pages Copy saved Nov 18, 2026

AC 91-74A Pilot Guide: Flight in Icing Conditions

This advisory circular (AC) contains updated and additional information for the pilots of airplanes under parts 91, 121, 125, and 135 of Title 14 of the Code of Federal Regulations (14 CFR). The purpose of this AC is to provide pilots with a convenient reference on the principal factors related to flight in icing conditions and the location of additional information in related publications. This AC does not authorize deviations from established company procedures or regulatory requirements.

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

FOREWORD

U.S. Department of Transportation Federal Aviation Administration

Advisory Circular

Subject: Pilot Guide: Flight In Icing Conditions Date: 12/31/07 Initiated by: AFS-800

AC No: 91-74A Change:

FOREWORD

This advisory circular (AC) contains updated and additional information for the pilots of airplanes under parts 91, 121, 125, and 135 of Title 14 of the Code of Federal Regulations (14 CFR). The purpose of this AC is to provide pilots with a convenient reference on the principal factors related to flight in icing conditions and the location of additional information in related publications. This AC does not authorize deviations from established company procedures or regulatory requirements.

ORIGINAL SIGNED by Carol Giles for

James J. Ballough Director, Flight Standards Service

CONTENTS

CONTENTS

Paragraph Page

CHAPTER 1. INTRODUCTION … 1

CHAPTER 2. TERMINOLOGY, ACRONYMS, AND ABBREVIATIONS … 3

2-1. Definitions … 3

CHAPTER 3. ATMOSPHERIC CONDITIONS ASSOCIATED WITH ICING … 9

3-1. Aircraft Icing Conditions … 9 3-2. Cloud Types and Aircraft Icing … 10 3-3. Fronts … 13 3-4. Convective Weather and Ice Crystals … 14

CHAPTER 4. ICING EFFECTS, PROTECTION, AND DETECTION … 15

4-1. Forms of Icing … 15 4-2. General Effects of Icing on Airfoils … 17 4-3. Effects of Icing on Wings … 18 4-4. Effects of Icing on Roll Control … 20 4-5. Tailplane Icing … 20 4-6. Propeller Icing … 21 4-7. Antenna Icing … 22 4-8. Cooling Inlet Icing … 22 4-9. Effects of Icing on Critical Systems … 22 4-10. Certification for Flight in Icing Conditions … 24 4-11. Significance of Icing Certification … 25 4-12. Ice Protection Equipment on Airplanes Not Certificated for Icing … 27 4-13. Anti-Icing Systems … 27 4-14. Deicing Systems … 28 4-15. Maintenance Considerations … 30 4-16. Icing Detection … 31 4-17. Visual Clues of SLD Conditions … 32

CHAPTER 5. FLIGHT PLANNING … 35

5-1. General Aviation Resources … 35 5-2. Air Carrier Dispatch Services … 35 5-3. Pireps … 35 5-4. Pirep Cautions … 36 5-5. Icing Forecasts … 37 5-6. Terminology Used in Icing Forecasts … 37 5-7. Current and Forecast Icing Products (CIP and FIP) … 38 5-8. Preflight Planning Information … 39 5-9. Airmet and Sigmet … 39

iii

iv

CHAPTER 6. IN-FLIGHT OPERATIONS … 41

6-1. Available In-Flight Information … 41 6-2. Pilot Strategies … 42

CHAPTER 7. ICING CONSIDERATIONS FOR THE PHASES OF FLIGHT … 45

7-1. Preflight … 45 7-2. Taxi … 47 7-3 Takeoff and Climbout … 47 7-4. Cruise … 47 7-5. Descent … 49 7-6. Holding … 49 7-7. Approach and Landing … 50 7-8. Wing Stall … 51 7-9. Ice-Contaminated Tailplane Stall (ICTS) … 51 7-10. Roll Upsets … 53

CHAPTER 8 SUMMARY … 55

APPENDIX 1, AIRCRAFT ACCIDENTS RELATED TO ICING (7 pages) … 1 APPENDIX 2, REGULATORY ISSUES RELATED TO ICING (7 pages) … 1 APPENDIX 3, ICING CHECKLISTS (8 pages) … 1 APPENDIX 4, RECOMMENDED READING (2 pages) … 1

CHAPTER 1. INTRODUCTION › 1-5.

CHAPTER 1. INTRODUCTION

1-1. This advisory circular (AC) updates the previous version and contains essential information concerning safe flight in icing conditions, what conditions should be avoided, and information on how to avoid or exit those conditions if encountered. The information provided is relevant to fixed-wing aircraft, including those operating under Title 14 of the Code of Federal Regulations (14 CFR) parts 91, 121, 125, and 135. The general guidance provided here in no way substitutes for aircraft type specific information in a particular Airplane Flight Manual (AFM) or specific Pilot’s Operating Handbook (POH).

1-2. This material is not regulatory, nor does it establish minimum standards. Where the term “must” is used in this AC, such use reflects actual regulatory requirements; where the term “should” is used, such reflects recommendations from the Federal Aviation Administration (FAA).

1-3. Aircraft icing remains a key aviation safety issue. Accident data has shown that pilots are (advertently and inadvertently) flying aircraft not certificated for flight in icing conditions into such conditions, often with fatal results. Even more disturbing are the numbers of accidents involving aircraft that are certificated for flight in icing conditions. Such accidents are often the result of pilot complacency, poor technique, poor understanding of the airplane’s limitations, and performance in icing conditions, misconceptions of airplane and system icing certification, and a misunderstanding of icing terminology. Education is the first step in reducing aircraft icing accidents.

1-4. Pilots must determine whether the aircraft to be flown is certificated for flight in icing conditions. An aircraft that is certificated for instrument flight rules (IFR) is not necessarily certificated for flight in icing conditions. To determine whether an aircraft is certificated for flight in icing conditions, the AFM or specific POH must be consulted. It is imperative that the pilot ensures that the aircraft is certificated to fly in icing conditions and that the appropriate deicing/anti-icing equipment is installed and operational. It is also of critical importance that the pilot understands and complies with the aircraft manufacturer’s limitations and procedures when operating in icing conditions.

1-5. If an aircraft is not certificated for flight in icing conditions, each flight should be planned carefully so that icing conditions are avoided. Chapter 3 provides information on when and where icing conditions may occur and Chapter 5 discusses flight planning. The flight should be planned to avoid clouds or precipitation where temperatures are near or below freezing. During flight, the pilot should monitor the information available (see Chapter 6 on in-flight operations) and be aware of conditions that might require a change of flight plan to avoid icing conditions. In the event of an inadvertent icing encounter, the pilot should take appropriate action to exit the conditions immediately, coordinating with air traffic control (ATC) as necessary, and declaring an emergency. In a recent study (AIAA 2006-82, “A Study of U. S. Inflight Icing Accidents and Incidents, 1978 to 2002”), conflicts with ATC are very prevalent. Very often, this was because the pilot deviated from an IFR clearance and failed to declare an emergency or otherwise clarify the situation with the controller. In a subset of these cases, the controller actually offers to declare an emergency for the pilot, but the pilot declines. In another subset, the frequency is too busy for communications, often because the controller is overwhelmed with traffic. A number of

CHAPTER 1. INTRODUCTION › 1-7.

pilots expected an immediate response from ATC when they reported difficulties after encountering ice and expected a blanket clearance to escape icing without first declaring a state of emergency. In many cases, such assumptions proved to be not only false, but also fatal.

1-6. This AC also includes information on a recently identified icing threat, high altitude ice crystal ingestion into turbine engines. Turbine engine upsets have occurred from ice accreting within the engine at altitudes up to 42,000 feet and temperatures colder than -45°C (-50°F). These high altitude ice crystals in large concentrations, typically found near convective weather systems, do not accrete on external airframe surfaces, and may not be visible on current technology airborne radar systems.

1-7. Many pilots of aircraft certificated to operate in icing conditions have had numerous icing encounters in which the aircraft systems coped effectively with the icing conditions — in some cases, even with a substantial ice buildup. However, a pilot should not relax his/her vigilance in icing conditions because of such experiences. A thin ice accretion on critical surfaces, developing in a matter of minutes, can have dramatic effects on stall speeds, stability, and control. Wind tunnel testing indicates that if such accretions are particularly rough, they can have more adverse effects than larger accretions that are relatively smooth.

2-1. DEFINITIONS. › f. Center Weather Advisory (CWA). An unscheduled weather advisory…

CHAPTER 2. TERMINOLOGY, ACRONYMS, AND ABBREVIATIONS

2-1. DEFINITIONS.

a. Adiabatic Cooling. A process by which a parcel of air cools. When a parcel of air is lifted, pressure is reduced due to the elevation increase. This reduction in pressure causes the parcel of air to expand in volume and in turn, the parcel cools to maintain an energy balance because no energy is added to the parcel.

b. Airman’s Meteorological Information (AIRMET). In-flight weather advisories concerning weather phenomena of operational interest to all pilots and especially to pilots of aircraft not approved for flight in icing conditions. AIRMETs concern weather of less severity than that covered by significant meteorological information (SIGMET) or Convective SIGMET. AIRMETs may include moderate icing.

c. Automated Surface Observing System (ASOS)/Automated Weather Observation System (AWOS). A suite of sensors that measure, collect, and disseminate weather data to help meteorologists, pilots, and flight dispatchers prepare and monitor weather forecasts, plan flight routes, and provide necessary information for correct takeoffs and landings. There are many differences between these two automated weather systems and it is important for pilots to understand the strengths and limitations of the various configurations. The ASOS is comprised of a standardized suite of weather sensors and is a product of a National Weather Service (NWS), Department of Defense (DOD), and FAA joint venture. One of ASOS’s most important features is its ability to detect precipitation including intensity of rain, snow, and freezing rain. One ASOS limitation that currently exists is its inability to detect and report freezing drizzle without human augmentation. Pilots should be aware of this limitation at airports deemed service level C or D, as described in the Aeronautical Information Manual (AIM). A detailed description of ASOS’s capabilities can be found at the NWS ASOS Homepage: http://www.nws.noaa.gov/asos/index.html.

d. The AWOS is a suite of weather sensors that are procured by the FAA or purchased by individuals, groups, airports, etc. There are seven different configurations of AWOS: AWOS A, AWOS I, AWOS II, AWOS III, AWOS III-P, AWOS-T, and AWOS P/T. Precipitation identification is only available with AWOS III-P or higher. It is important to note that the absence of reported precipitation does not mean that such conditions do not exist. The AWOS may not be configured to report this information. A detailed description of AWOS’s capabilities can be found in FAA AC 150/5220-16C, Automated Weather Observing Systems (AWOS) for Non-Federal Applications. The AIM also contains useful information on both ASOS and AWOS.

e. Aviation Weather Service Program. Aviation weather service provided by the NWS and the FAA that collects and disseminates pertinent weather information for pilots, aircraft operators, and ATC. Available aviation weather reports and forecasts are produced at NWS offices and displayed at FAA Flight Service Stations (FSS).

f. Center Weather Advisory (CWA). An unscheduled weather advisory issued by NWS meteorologists for use by ATC in alerting pilots of existing or anticipated adverse weather conditions within the next two hours. A CWA may modify a SIGMET.

g. Clear Ice. A glossy, clear, or translucent ice formed by the relatively slow freezing of large supercooled water droplets. The terms “clear” and “glaze” have been used for essentially the same type of ice accretion, although some reserve “clear” for thinner accretions which lack horns and conform to the airfoil.

2-1. DEFINITIONS. › q. Heavy Icing. The rate of ice accumulation requires maximum use of…

h. Cold Front. Any nonoccluded front that moves in such a way that colder air replaces warmer air.

i. Convection. An atmospheric motion that is predominantly vertical, resulting in the transport and mixing of atmospheric properties.

j. Cumulus Clouds. Clouds in the form of detached domes or towers and are usually well defined. Cumulus clouds develop vertically in the form of rising mounds of which the bulging upper part often resembles a cauliflower; the sunlit parts of these clouds are mostly brilliant white. Their bases may be relatively dark and nearly horizontal.

k. Current Icing Product (CIP). A graphical planning product that combines sensor and numerical model data to provide a three-dimensional diagnosis of the probability and severity of icing, plus the potential for the presence of supercooled large drops (SLD). CIP is an unrestricted supplementary weather product.

l. Forecast Icing Product (FIP). The FIP examines numerical weather prediction model output to calculate the probability of encountering in-flight aircraft icing conditions. This icing product demonstrates the confidence that an atmospheric location, represented by a three-dimensional model grid box, will contain supercooled liquid water that is likely to form ice on an aircraft.

m. Freezing Drizzle. Drizzle is precipitation at ground level or aloft in the form of liquid water drops that have diameters less than 0.5 mm and greater than 0.05 mm. Freezing drizzle is drizzle that exists at air temperatures less than 0°C (supercooled), remains in liquid form, and freezes upon contact with objects on the surface or airborne.

n. Freezing Rain. Rain is precipitation at ground level or aloft in the form of liquid water drops which have diameters greater than 0.5 mm. Freezing rain is rain that exists at air temperatures less than 0°C (supercooled), remains in liquid form, and freezes upon contact with objects on the ground or in the air.

o. Front. The boundary between two air masses. A front can be classified as cold, warm, occluded, or stationary.

p. Hazardous Weather Information. Summary of SIGMETs, Convective SIGMETs, urgent pilot weather reports, CWAs, AIRMETs, and any other weather, such as isolated thunderstorms rapidly developing and increasing in intensity or low ceilings and visibilities becoming widespread, that is considered significant and is not included in a current hazardous weather advisory.

q. Heavy Icing. The rate of ice accumulation requires maximum use of the ice protection systems to minimize ice accretions on the airframe. A representative accretion rate for

r. Icing Conditions. › w. Light Icing. The rate of ice accumulation requires occasional…

reference purposes is more than 3 inches (7.5 cm) per hour1 on the outer wing. Consider immediate exit from the conditions.2

r. Icing Conditions.

(1) Potential Icing Conditions. Atmospheric icing conditions that are typically defined by airframe manufacturers relative to temperature and visible moisture that may result in aircraft ice accretion on the ground or in flight. The potential icing conditions are typically defined in the airplane flight manual or in the airplane operation manual.

(2) Forecast Icing Conditions. Environmental conditions expected by a NWS or an FAA-approved weather provider to be conducive to the formation of in-flight icing on aircraft.

s. Ice Crystals. Ice crystals, often found in high concentrations near convective weather systems, can accrete within turbine engines and cause power loss. Ice crystals are not typically detected by either conventional ice detectors or airborne radar, and typically do not accrete on external airframe surfaces. Ice crystals found in stratus and cirrus clouds are usually in relatively low concentrations, and do not represent a threat to turbine engines.

t. Icing Envelopes. These icing envelopes, found in 14 CFR part 25, appendix C, are used for the certification of aircraft for flight in icing conditions. They specify atmospheric icing conditions in terms of altitude, temperature, liquid water content (LWC), and droplet size represented by the median volume diameter (MVD). (The envelopes use the term mean effective diameter (MED), but this equates to the median volume diameter for the instrumentation and assumptions current at the time the envelopes were established). There are two classes of icing envelopes: continuous maximum and intermittent maximum. The continuous maximum is for stratus-type clouds, and the intermittent maximum is for cumulus-type clouds.

u. Impinge. The striking and adherence of a droplet on an aircraft surface. The impingement rate is the rate at which droplets of a given size impinge a particular surface. In general, impingement rates are higher for larger droplets and smaller components, such as antennae.

v. Known, Observed, or Detected Ice Accretion. Actual ice that is observed visually to be on the aircraft by the flight crew or identified by onboard sensors.

w. Light Icing. The rate of ice accumulation requires occasional cycling of manual deicing systems 3 to minimize ice accretions on the airframe. A representative accretion rate for

1 These rates can be measured by a suitable icing rate meter.

2 It is expected that deicing or anti-icing systems will be activated and operated continuously in the automatic mode, if available, at the first sign of ice accumulation, or as directed in the AFM. Occasional and frequent cycling refers to manually activated systems.

3 See footnote number 2

r. Icing Conditions. › ff.

reference purposes is 1⁄4 inch to one inch (0.6 to 2.5 cm) per hour 4 on the outer wing. The pilot should consider exiting the condition.5

x. Liquid Water Content (LWC). The total mass of water in all the liquid cloud droplets within a unit volume of cloud. LWC is usually discussed in terms of grams of water per cubic meter of air (g/m3).

y. Median Volume Diameter (MVD). The diameter is such that half the liquid water in a region of cloud is contained in smaller drops, and half in larger drops.

z. Mixed Ice. Simultaneous appearance of rime and clear ice or an ice formation that has the characteristics of both rime and clear ice.

aa. Moderate Icing. The rate of ice accumulation requires frequent cycling of manual deicing systems6 to minimize ice accretions on the airframe. A representative accretion rate for reference purposes is 1 to 3 inches (2.5 to 7.5 cm) per hour 7 on the outer wing. The pilot should consider exiting the condition as soon as possible.8

bb. Occluded Front. The front formed by a cold front overtaking a warm front and lifting the warm air above the earth’s surface. An occlusion (or frontal occlusion) forms when an air mass is trapped between two colder air masses and is forced to higher and higher levels.

cc. One-Minute Weather. The most recent 1-minute update weather broadcast based on ASOS/AWOS measurements and available to a pilot from an uncontrolled airport ASOS/AWOS.

dd. Orographic Cloud. A cloud that usually results from air flowing upslope from terrain and being cooled adiabatically.

ee. Outside Air Temperature (OAT). The measured or indicated air temperature (IAT) corrected for compression and friction heating. Also referred to as true air temperature.

ff. Pilot Briefing. A service provided by a Flight Service Station (FSS) to assist pilots with flight planning. Briefing items may include weather information, notices to airmen (NOTAMs), military activities, flow control information, and other items, as requested.

4 See footnote number 1.

5 It is assumed that the aircraft is approved to fly in the cited icing conditions. Otherwise, immediate exit from any of these intensity categories is required by regulations (14 CFR §§ 91.13(a), 91.527, 121.341, 125.221, and 135.227).

6 See footnote number 1.

7 See footnote number 2.

8 See footnote number 3.

r. Icing Conditions. › qq.

gg. Pilot Report (PIREP). A report from a pilot of meteorological phenomena encountered by aircraft in flight, usually transmitted in a prescribed format. The letters “UA” identify the message as a routine PIREP while the letters “UUA” identify an urgent PIREP.

hh. Rime Ice. A rough, milky, opaque ice formed by the instantaneous freezing of small, supercooled water droplets.

ii. Runback Ice. Ice that forms from the freezing or refreezing of water leaving protected surfaces and running back to unprotected surfaces.

jj. Severe Icing. The rate of ice accumulation is such that ice protection systems fail to remove the accumulation of ice and ice accumulates in locations not normally prone to icing, such as areas aft of protected surfaces and any other areas identified by the manufacturer. Immediate exit from the condition is necessary.9

kk. Significant Meteorological Information (SIGMET). Information about in-flight weather of operational significance to the safety of all aircraft. SIGMETs may include severe icing. (See CWA and AIRMET.)

ll. Stagnation Point. The point on a surface where the local air velocity is zero. The region of maximum icing collection efficiency is near this point.

mm. Stationary Front. A front that has little or no movement because the opposing forces of the two air masses are relatively balanced.

nn. Stratus Clouds. Clouds that form layers with a uniform base. Stratus clouds can appear in ragged patches and may produce drizzle, rain, or snow.

oo. Sublimation. A process where ice turns directly into water vapor without passing through a liquid state.

pp. Supercooled Large Drop (SLD). A supercooled droplet with a diameter greater than 50 micrometers (0.05 mm). SLD conditions include freezing drizzle drops and freezing raindrops.

qq. Supplemental Weather Service Location. An airport facility staffed with contract personnel who take weather observations and provide current local weather to pilots via telephone or radio.

9 Severe icing is aircraft dependent, as are the other categories of icing intensity. Severe icing may occur at any ice accumulation rate

when the icing rate or ice accumulations exceed the tolerance of the aircraft. Icing certification implies an increased tolerance to icing

intensities up through heavy.

rr. Telephone Information Briefing Service (TIBS). A telephone recording of meteorological and/or aeronautical information obtained by calling an FSS.

r. Icing Conditions. › vv.

ss. Total Air Temperature (TAT). Kinetic heating causes the Total (or Ram) Air Temperature (TAT) to be warmer than the Static Air Temperature (SAT). TAT is close to the temperature of the wing leading edge, which also experiences ram rise.

tt. Trace Icing. Ice becomes noticeable. The rate of accumulation is slightly greater than the rate of sublimation. A representative accretion rate for reference purposes is less than 1/4 inch (6 mm) per hour on the outer wing. The pilot should consider exiting the icing conditions before they become worse. Pilots should be aware that any ice, even in trace amounts, could be potentially hazardous.

uu. Warm Front. Any nonoccluded front that moves in such a way that warmer air replaces colder air.

vv. Weather Advisory. In standard aviation weather forecast terminology, a warning of hazardous weather conditions not predicted in the forecast area that may affect air traffic operations. These reports are prepared by the NWS.

3-1. AIRCRAFT ICING CONDITIONS. › f. Every supercooled cloud contains a broad range of droplets, starting…

CHAPTER 3. ATMOSPHERIC CONDITIONS ASSOCIATED WITH ICING

3-1. AIRCRAFT ICING CONDITIONS.

a. Nearly all aircraft icing occurs in supercooled clouds. Liquid droplets are present at outside air temperatures below 0°C (32°F) in these clouds. At outside air temperatures close to 0°C (32°F), the cloud may consist entirely of such droplets, with few or no ice particles present. At decreasing temperatures, the probability increases that ice particles will be found in significant numbers along with the liquid droplets. In fact, as the ice water content increases, the liquid water content tends to decrease since the ice particles grow at the expense of the water particles. At temperatures below about -20°C (-4°F), most clouds are made up entirely of ice particles.

b. The general rule is that the more ice particles and the fewer liquid droplets that are present, the less ice accumulation on the airframe. This is because the ice particles tend to bounce off an aircraft surface, while the supercooled droplets freeze and adhere. As a result, ice accumulation is often greatest at temperatures not too far below 0 °C (32°F), where liquid water content can be abundant, and is usually negligible at temperatures below about -20°C (-4°F).

c. An exception to the general rule just stated may be made for surfaces heated by a thermal ice protection system (or by aerodynamic heating near the stagnation point of an aircraft component at speeds in excess of perhaps 250 knots). For such surfaces, ice particles may melt upon impact and then run back to colder aft regions and refreeze.

d. The higher liquid water content associated with temperatures near freezing is not the only concern. Tests have shown that at outside air temperatures near freezing, the total air temperature may be above freezing. The result is no ice accretion near the stagnation, but the refreezing of the water running back on the airfoil, causing runback ice accretions, possibly behind the protected areas. The formation of a ridge is possible. Pilots should be vigilant at total temperatures (TAT) between -5°C (23°F) and +2°C (35°F). Pilots should know whether the temperature instrument they are reading in the cockpit is outside air temperature (OAT) or TAT.

e. The greater the liquid water content of the cloud, the more rapidly ice accumulates on aircraft surfaces. The size of the droplets also is important. Larger droplets have greater inertia and are less influenced by the airflow around the aircraft than smaller droplets. The result is that larger droplets will impinge on more of the aircraft surface than smaller droplets.

f. Every supercooled cloud contains a broad range of droplets, starting from between 1 and 10 micrometers (millionth of a meter) and usually not exceeding 50 micrometers (by comparison, the thickness of the average human hair is approximately 100 micrometers). A single droplet size must be chosen as representative, and in icing terminology this is the MVD, the diameter such that half the liquid water is in smaller drops, and half in larger drops. An icing-certificated aircraft is certificated for flight in stratus-type clouds with MVDs up to 40 micrometers and for cumulus-type clouds with MVDs up to 50 micrometers. The MVD distribution is such that aircraft that undergo icing certification are not evaluated for operations in clouds with a significant amount of liquid water in droplets with diameters larger than 100 micrometers. Such conditions are sometimes encountered, and accidents and incidents in

c. Several types of clouds and the hazardous aircraft icing conditions… › (b) Lakeeffect stratus clouds are exceptional in that they may have…

such conditions have been documented. These conditions are referred to as freezing drizzle aloft in cloud or SLD in cloud. Table 1, Evolution of Icing Certification Standards, discusses some cues developed for aircraft with unpowered controls and pneumatic deicing boots, mainly relating to the location of the airframe ice, which the flightcrew can use in attempting to determine if such droplets may be present in a cloud.

g. An aircraft can also encounter SLD conditions in freezing drizzle (droplets with a diameter of 50 to 500 micrometers) or freezing rain (droplets with a diameter of 500 micrometers and larger) below a cloud deck. These droplets are, by definition, larger than those for which any aircraft is certificated, and accidents and incidents have occurred following flight in freezing drizzle or freezing rain. The larger drops can cause ice accretion behind the protected leading edge.

3-2. CLOUD TYPES AND AIRCRAFT ICING.

a. Air can rise because of many factors, including convection, orographic lifting (i.e., air forced up a mountain), or lifting at a weather front. As the air rises, it expands and cools adiabatically. If a parcel of air reaches its saturation point, the moisture within the parcel will condense and the resulting droplets form a cloud. Cloud water droplets are generally very small, averaging 20 micrometers in diameter, and are of such small mass that they can be held aloft by small air currents within clouds.

b. If rising air is moist (water vapor plentiful) and lifting is vigorous, the result can be clouds with substantial liquid water content and, sometimes, large droplets. The greater the liquid water content, the more rapid the icing; and the larger the droplets, the greater the extent of icing. Tops of clouds often contain the most liquid water and largest droplets, because the droplets that reach the tops have undergone the most lifting. If the temperatures are cold enough at the tops (below around -15 °C (5 °F)), however, ice particles will usually start to form, which tends to deplete the liquid water.

c. Several types of clouds and the hazardous aircraft icing conditions that may be associated with them are discussed below.

(1) Stratus Clouds.

(a) Stratus clouds, sometimes called layer clouds, form a stratified layer that may cover a wide area. The lifting processes that form them are usually gradual, and so they rarely have exceptionally high liquid water contents. Icing layers in stratus clouds with a vertical thickness in excess of 3,000 feet are rare, so a change of altitude of a few thousand feet may take the aircraft out of icing.

(b) Lake-effect stratus clouds are exceptional in that they may have very high liquid water content because of the moisture available when they form over lakes. In the continental United States, lake-effect stratus clouds are most common in the Great Lakes region, particularly in early winter when cold northwesterly winds blow over the unfrozen lakes.

d. Freezing Rain and Freezing Drizzle. › (2) Freezing raindrops are defined as drops of 500 micrometers (0.5 mm)…

(c) Drizzle-size drops occasionally occur in stratus clouds, and pilots should always be on the lookout for cues that might indicate the presence of these drops (see Table 1 for a list of cues developed for aircraft with unpowered controls and pneumatic deicing boots).

(2) Cumulus Clouds.

(a) Cumulus clouds, which often form because of vigorous convection, can have high liquid water content. If an aircraft traverses them, the icing can be rapid. Because they tend to be of limited horizontal extent, it may be possible to avoid many of them. Because of the vertical development of cumulus clouds, icing conditions can be found in layers thousands of feet in depth, but with much less horizontal development than in stratus clouds.

(b) This class of clouds includes the cumulonimbus, or thunderstorm, clouds. Updrafts in such clouds can be great and result in very large liquid water contents. Thus, a large icing threat can be added to the other excellent reasons to stay out of such clouds. The thunderhead anvil can spread out from the core for several miles and is composed mainly of ice crystals. These crystals will not adhere to unheated surfaces when they hit, but they may melt on a heated surface, run back, and refreeze. The ice content in the anvils can be high, and ingestion of the ice crystals has resulted in uncommanded thrust reductions.

(3) Orographic Clouds, Wave Clouds, and Cirrus Clouds.

(a) Orographic clouds form when moist air is lifted by flowing up the side of a mountain. As the parcel of air is lifted, it cools and forms a cloud. Such clouds can contain a large volume of water, and in some cases, large droplets.

(b) Wave clouds, recognized by their “wavy” tops, can have high liquid water contents. Continued flight along a wave may result in airframe icing.

(c) Cirrus clouds, found at very high, cold altitudes, are composed entirely of ice particles. Flight through these clouds should not result in structural icing, although the possibility exists for runback icing from the refreezing of particles that melted on thermally or aerodynamically heated surfaces.

d. Freezing Rain and Freezing Drizzle.

(1) Freezing rain forms when rain becomes supercooled by falling through a subfreezing layer of air. Ordinarily, air temperatures decrease with increasing altitude, but freezing rain requires a temperature inversion, which can occur when a warmer air mass overlies a colder air mass. This situation can occur along a warm front, where a warm air mass overruns a cold air mass. When flying in freezing rain, normally there is warm air (above 0 °C (32 °F)) above.

(2) Freezing raindrops are defined as drops of 500 micrometers (0.5 mm) diameter or larger. A typical diameter is 2 mm, and the few that grow much larger than about 6 mm tend to break up. Using 20 micrometers (0.02 mm) as a typical diameter for a cloud droplet, the diameters of rain and cloud drops differ by a factor of approximately 100, and the volume and mass differ by a factor of about 1,000,000. The size difference is shown in Figure 1. Droplet

d. Freezing Rain and Freezing Drizzle. › (5) The diameters of representative cloud and drizzle drops differ by a…

mass affects how far aft of the stagnation point (leading edge surfaces) droplets will strike the aircraft. The mass of freezing rain is typically 1,000,000 times that of cloud droplets. Because of this, freezing rain will result in ice forming in areas far aft of where it would form in ordinary supercooled clouds.

FIGURE 1. DROPLET SIZE COMPARISON

Typical raindrop 2 millimeters

Typical cloud droplet 0.02 millimeters

(3) Freezing drizzle also can form through the same process. It consists of supercooled liquid water drops that have diameters smaller than 500 micrometers (0.5 mm) and greater than 50 micrometers (0.05 mm).

(4) However, freezing drizzle is perhaps more commonly formed by a different process, known as the collision-coalescence process. When, through condensation, some droplets in a cloud grow to approximately 30 micrometers in diameter, they begin to settle, falling fast enough so that they collide with some smaller droplets. If the droplets coalesce, the result is a larger droplet, which now has an even better chance of capturing smaller droplets. Under favorable conditions, this process can produce drizzle-size drops in a supercooled cloud, usually near the top, where the larger droplets generally are found in any cloud. Statistics vary, but some studies have reported that freezing drizzle aloft forms more than 80 percent of the time by the collision-coalescence process in non-convective clouds. Thus, in freezing drizzle, the pilot cannot assume that a warm layer (above 0°C (32°F)) exists above the aircraft.

(5) The diameters of representative cloud and drizzle drops differ by a factor of about 10 and the volume and mass by a factor of about 1,000. The greater inertia and impingement efficiency of the drizzle drops will result in icing beyond the usual icing limits for typical cloud droplets. When drizzle drops are found within a supercooled cloud, they can result

3-3. FRONTS. › b. Along a warm front, the warmer air tends to slide gradually over the…

in accretions that cause very rapid and dangerous stall speed and drag increases for some aircraft and roll control anomalies for others. These situations may be caused by the roughness, shape, and extent of the accretion that forms. This is an instance of SLD icing as discussed earlier in this paragraph. (See Table 1 for a list of cues developed for aircraft with unpowered controls and pneumatic deicing boots.)

3-3. FRONTS.

a. When air masses of differing temperatures, pressures, or relative humidity meet, a front is formed. If the front moves so that warmer air replaces colder air, it is called a warm front; if it moves so that colder air replaces warmer air, it is called a cold front. An occluded front forms when an air mass is trapped between two colder air masses and is forced to higher and higher levels. In all three cases, significant lifting occurs. If sufficient moisture and subfreezing temperatures are present, icing conditions are created.

b. Along a warm front, the warmer air tends to slide gradually over the cold front, forming stratus clouds conducive to icing (see Figure 2). In a cold front, the cold air plows under the warm air, lifting it more rapidly and resulting in the formation of cumulus clouds with high liquid water content if the lifted air is moist (see Figure 3). SLD in the form of freezing rain and freezing drizzle are sometimes found near fronts, as explained above.

FIGURE 2. WARM FRONT

FIGURE 3. COLD FRONT

3-4. CONVECTIVE WEATHER AND ICE CRYSTALS. › c. Dry ice crystals, particularly those found above 25,000 feet…

c. Because of the icing and other hazards associated with fronts, they are best avoided, if possible. When flying through a front, the shortest route through the front should be taken, instead of flying along the front, to reduce the time spent in potential icing conditions.

3-4. CONVECTIVE WEATHER AND ICE CRYSTALS.

a. Some turbine engine designs have shown a susceptibility to ice crystals that form in the atmosphere because of convective weather activity. Deep lifting (thousands of feet) and condensation of water vapor in an unstable atmosphere characterize convective weather. Some or all of the following can be found in areas of convection: strong wind shear, turbulence, lightning, and high-condensed water or hail. Convective weather can range from isolated thunderstorms or cumulonimbus clouds, to convective complexes or squall lines to tropical storms or hurricanes. It can extend hundreds of miles laterally and above 50,000 feet vertically. Convective weather systems, especially, those associated with tropical weather fronts can pump large quantities of moisture to high altitudes that freezes into ice crystals that can remain aloft. These ice crystals can remain as a cloud well after the convective system has decayed.

b. These clouds of ice crystals may not be detectable on conventional airborne radar. Although these ice crystals do not typically accrete on airframe surfaces or trigger ice detectors, when present in high concentrations they can still accrete on warm surfaces within the flow-path of turbine engines. This accretion can ultimately result in engine upset, engine damage from shedding, or power loss.

c. Dry ice crystals, particularly those found above 25,000 feet altitude, do not provide good radar reflectivity. Dry ice particles have about 20 times less radar reflectivity than rain droplets, and therefore are difficult to detect. Clouds and temperatures less than ten degrees centigrade are better indicators of the possible presence of ice crystals when near convective weather. Follow AFM procedures.

a. Structural Icing. Ice forms on aircraft structures and surfaces when… › (2) Rime Ice.

CHAPTER 4. ICING EFFECTS, PROTECTION, AND DETECTION

4-1. FORMS OF ICING. Aircraft icing in flight is usually classified as being either structural icing or induction icing. Structural icing refers to the ice that forms on aircraft surfaces and components, and induction icing refers to ice in the engine’s induction system.

a. Structural Icing. Ice forms on aircraft structures and surfaces when supercooled droplets impinge on them and freeze. Small and/or narrow objects are the best collectors of droplets and ice up most rapidly. This is why a small protuberance within sight of the pilot can be used as an “ice evidence probe.” It will generally be one of the first parts of the airplane on which an appreciable amount of ice will form. An aircraft’s tailplane will be a better collector than its wings, because the tailplane presents a thinner surface to the airstream. The type of ice that forms can be classified as clear, rime, or mixed, based on the structure and appearance of the ice. The type of ice that forms varies depending on the atmospheric and flight conditions in which it forms.

(1) Clear Ice. A glossy, transparent ice formed by the relatively slow freezing of supercooled water (see Figure 4). The terms “clear” and “glaze” have been used for essentially the same type of ice accretion. This type of ice is denser, harder, and sometimes more transparent than rime ice. With larger accretions, clear ice may form “horns” (see Figure 5). Temperatures close to the freezing point, large amounts of liquid water, high aircraft velocities, and large droplets are conducive to the formation of clear ice.

FIGURE 4. CLEAR ICE

FIGURE 5. CLEAR ICE BUILDUP WITH HORNS

(2) Rime Ice. A rough, milky, opaque ice formed by the instantaneous or very rapid freezing of supercooled droplets as they strike the aircraft (see Figure 6). The rapid freezing results in the formation of air pockets in the ice, giving it an opaque appearance and making it porous and brittle. For larger accretions, rime ice may form a streamlined extension of the wing. Low temperatures, lesser amounts of liquid water, low velocities, and small droplets favor formation of rime ice.

b. Induction Icing. › (3) Ice also may accumulate on both the engine inlet section and on the…

FIGURE 6. RIME ICE

(3) Mixed Ice. Mixed ice is a combination of clear and rime ice formed on the same surface. It is the location, size, shape, and roughness of the ice that is most important from an aerodynamic point of view. This is discussed later in this chapter, on effects of icing.

b. Induction Icing.

(1) Ice in the induction system can reduce the amount of air available for combustion. The most common example of reciprocating engine induction icing is carburetor ice. Most pilots are familiar with this phenomenon, which occurs when moist air passes through a carburetor venturi and is cooled. As a result of this process, ice may form on the venturi walls and throttle plate, restricting airflow to the engine. This may occur at temperatures between 20°F (-7°C) and 70°F (21°C). The problem is remedied by applying carburetor heat, which uses the engine’s own exhaust as a heat source to melt the ice or prevent its formation. Fuel-injected aircraft engines usually are less vulnerable to icing, but still can be affected if the engine’s air source becomes blocked with ice. Manufacturers provide an alternate air source that may be selected in case the normal system malfunctions.

(2) In turbine engine powered aircraft, air that is drawn into the engines creates an area of reduced pressure at the inlet, which lowers the temperature below that of the surrounding air. In marginal icing conditions (i.e., conditions where icing is possible), this reduction in temperature may be sufficient to cause ice to form on the engine inlet, disrupting the airflow into the engine. Another hazard occurs when ice breaks off and is ingested into a running engine, which can cause damage to fan blades, engine compressor stall, or combustor flameout. When anti-icing systems are used, runback water also can refreeze on unprotected surfaces of the inlet and, if excessive, reduce airflow into the engine or distort the airflow pattern in such a manner as to cause compressor or fan blades to vibrate, possibly damaging the engine. Another problem in turbine engines is ice, particularly snow and ice crystals accumulating on the engine probes used to set power levels (for example, engine inlet temperature or engine pressure ratio (EPR) probes), which can lead to erroneous readings of engine instrumentation (see the description of the Air Florida B-737 accident in Appendix 1, paragraph 2).

(3) Ice also may accumulate on both the engine inlet section and on the first or second stage of the engine’s low-pressure compressor stages. This normally is not a concern with pitot-style engine airflow inlets (that is, straight-line-of-sight inlet design). However, on turboprop engines that include an inlet section with sharp turns or bird-catchers, however, ice can accumulate in the aerodynamic stagnation points at the bends in the inlet duct. If ice does accumulate in these areas, it can shed into the engine, possibly resulting in engine operational difficulties or total power loss. Therefore, with these types of engine configurations, the use of anti-icing or deicing systems per the AFM is very important. Supercooled water droplets tend to form ice on the turbine engine inlet, fan, and first few stages of the compressor. Ice crystals, when present in high concentrations, tend to form ice deeper in the turbine engine’s compressor

4-2. GENERAL EFFECTS OF ICING ON AIRFOILS. › b. Figure 8 shows how ice affects the coefficient of drag of the…

section. Ice accretions can ultimately shed and damage the compressor, or cause engine surge or flameout. These conditions are analyzed and tested during original engine airworthiness approvals. These tests are conducted to demonstrate the turbine engine’s tolerance to these conditions.

4-2. GENERAL EFFECTS OF ICING ON AIRFOILS. The two figures in this chapter depict important information on the effects of ice contamination on an airfoil. (For this AC, an airfoil is a cross-section of a wing or tailplane.)

a. Figure 7 shows how ice often affects the coefficient of lift for an airfoil. Note that at very low angles of attack, there may be little or no effect of the ice on the coefficient of lift. Thus when cruising at a low angle of attack (AOA), ice on the wing may have little effect on the lift. However, note that the maximum coefficient of lift (CLmax) is significantly reduced by the ice, and the AOA at which it occurs (the stall angle) is much lower. Thus when slowing down and increasing the AOA for approach, therefore, the pilot may find that ice on the wing that had little effect on lift in cruise now causes stall to occur at a lower AOA and higher speed. Even a thin layer of ice at the leading edge of a wing, especially if it is rough, can have a significant effect in increasing stall speed. For large ice shapes, especially those with horns, the lift may also be reduced at a lower AOA as well. Depending on the airfoil section, the lift loss may even be larger if ice accretes behind areas normally protected, such as due to large drop impingement and runback.

FIGURE 7. LIFT CURVE

Clean Airfoil

Airfoil With Ice

Angle of Attack

CL (coefficient of lift)

b. Figure 8 shows how ice affects the coefficient of drag of the airfoil. Note that the effect is significant even at very small AOAs.

(1) A significant reduction in CLmax and a reduction in the AOA where stall occurs can result from a relatively small ice accretion. A reduction of CLmax by 30 percent is not unusual, and a large horn ice accretion can result in reductions of 40 percent to 50 percent. Drag tends to increase steadily as ice accretes. An airfoil drag increase of 100 percent is not unusual, and, for large horn ice accretions, the increase can be 200 percent or even higher.

4-3. EFFECTS OF ICING ON WINGS. › a. Unprotected Wing. An aircraft with a completely unprotected wing…

FIGURE 8. DRAG CURVE

Clean Airfoil

Airfoil With Ice

Angle of Attack

CD (coefficient of drag)

(2) Ice on an airfoil can have other effects not depicted in these curves. Even before airfoil stall, there can be changes in the pressure over the airfoil that may affect a control surface at the trailing edge. Furthermore, on takeoff, approach, and landing, the wings of many aircraft are multi-element airfoils with three or more elements. Ice may affect the different elements in different ways and affect the way in which the flows over the elements interact.

4-3. EFFECTS OF ICING ON WINGS. The effect of icing on a wing depends on whether the wing is protected and the kind and extent of protection provided.

a. Unprotected Wing. An aircraft with a completely unprotected wing will not be certificated for flight in icing conditions, but it may inadvertently encounter icing conditions. Since a cross-section of a wing is an airfoil, the remarks above on airfoils apply to a wing with ice along its span. The ice causes an increase in drag, which the pilot detects as a loss in airspeed. An increase in power is required to maintain the same airspeed. (The drag increase is also due to ice on other parts of the aircraft). The longer the encounter, the greater the drag increase; even with increased power, it may not be possible to maintain airspeed. The ice on the wing also causes a decrease in CLmax, possibly about 30 percent, for an extended encounter. The rule of thumb is that the percentage increase in stall speed is approximately half the decrease in CLmax, so the stall speed may go up by about 15 percent. If the aircraft has relatively limited power (as is the case with many aircraft with no ice protection), it may soon approach stall speed and a very

c. AntiIced Wing. › (2) Antiicing systems can be evaporative or running wet.

dangerous situation. A similar scenario applies to aircraft that are certificated for flight in icing conditions if the wing ice protection system fails in icing conditions.

b. Deiced Wing. The FAA recommends that the deicing system be activated at the first indication of icing. Because some residual ice continues to adhere between pneumatic boot system cycles, the wing is never entirely “clean.” The amount of residual ice increases as airspeed or temperature decreases. At airspeeds typical of small airplanes (demonstrated in tunnel tests at airspeeds below 145 knots calibrated airspeed (KCAS)), it may take many boot cycles to effectively shed the ice. It may appear that the boots are not having any effect at all until shedding occurs.

(1) Use of ice adhesion inhibitors on pneumatic deicing boots is highly recommended; consult the AFM or maintenance manual for the recommended product and application interval. The ice that can build between boot cycles, called intercycle ice, can be significant. On many icing accidents and incidents, loss of airspeed and stall can occur in a span of minutes. Ice accretion will decrease CLmax, which will translate into an increase in stall speed.

(2) The increase in stall speed becomes more of a concern at the higher AOAs characteristic of approach and landing because the aircraft is operating closer to CLmax. Thus the pilot should consider continuing activation of the deicing system for a period after exiting the icing conditions so that the wing will be as clean as possible and any effect on stall speed minimized. If the icing conditions cannot be exited until late in the approach or significant icing appears to remain on the wing after activating the system, an increase in the aircraft’s stall speed is a possibility and adjustment of the approach speed may be appropriate. Consult the AFM or POH for guidance.

(3) Intercycle ice will also accrete on airplanes with electrothermal deicing systems. It is typical for these systems also to produce runback ice behind the protected area.

c. Anti-Iced Wing.

(1) An anti-icing system is designed to keep a surface entirely free of ice throughout an icing encounter. Anti-icing protection for wings is normally provided by ducting hot bleed air from the engines into the inner surface of the wing’s leading edge and thus is found mainly on transport turbojets and business jets, but not on turbopropeller or piston airplanes. Even on transport and business jets, there are often sections along the span of the wing that are not protected. An important part of icing certification for these planes is checking that the protected sections are extensive enough and properly chosen so that ice on the unprotected areas will not affect the safety of flight.

(2) Anti-icing systems can be evaporative or running wet. On newer designs, the wing anti-ice system may be running wet by design, forming runback ice accretions. The effects of these accretions are evaluated during certification, but only in part 25, appendix C icing conditions. Runback ice can serve as accretion sites for additional accumulations.

4-5. TAILPLANE ICING. › a. Most aircraft have a nosedown pitching moment from the wings because…

4-4. EFFECTS OF ICING ON ROLL CONTROL.

a. This chapter is in effect a continuation of the previous one, since ice on the wings forward of the ailerons can affect roll control. The ailerons are generally close to the tip of the wing, and wings are designed so that stall starts near the root of the wing and progresses outward. In this way, the onset of stall does not interfere with roll control of the ailerons. However, the tips are usually thinner than the rest of the wing, and so they most efficiently collect ice. This can lead to a partial stall of the wings at the tips, which can affect the ailerons and thus roll control.

b. If ice accumulates in a ridge aft of the boots, but forward of the ailerons, possibly due to flight in SLD conditions, this can affect the airflow and interfere with the proper functioning of the ailerons, even without a partial wing stall at the tip.

(1) This is the phenomenon that the National Transportation Safety Board (NTSB) found to be responsible for the accident of an ATR-72 turbopropeller aircraft in Roselawn, Indiana in October 1994 (see Appendix 1, paragraph 1). Flight test investigations following the accident suggested two ways in which the ailerons might be affected by ice in front of them.

(2) One has been termed “aileron snatch,” in which an imbalance of forces at the aileron is felt by the pilot of an aircraft without powered controls as a sudden change in the aileron control force. Provided the pilot is able to adjust for the unusual forces, the ailerons may still be substantially effective when they are deflected. The other is that ailerons may be affected in a substantial degradation in control effectiveness, although without the need for excessive control forces.

4-5. TAILPLANE ICING.

a. Most aircraft have a nose-down pitching moment from the wings because the center of gravity (CG) is ahead of the center of pressure. It is the role of the tailplane to counteract this moment by providing “downward” lift (see Figure 9). The result of this configuration is that actions that move the wing away from stall, such as deployment of flaps or increasing speed, may increase the negative AOA of the tail. With ice on the tailplane, it may stall after full or partial deployment of flaps (see Figure 10).

FIGURE 9. TAIL DOWN MOMENT

Tail Download

C of L

CG

Weight

4-1. FORMS OF ICING. › 4-6. PROPELLER ICING.

b. Since the tailplane is ordinarily thinner than the wing, it is a more efficient collector of ice. On most aircraft, the tailplane is not visible to the pilot, who therefore cannot observe how well it has been cleared of ice by any deicing system. Thus, it is important that the pilot be alert to the possibility of tailplane stall, particularly on approach and landing. A no-flap landing should be considered to avoid a tailplane stall, consistent with AFM procedures. Tailplane stall is discussed in detail in Chapter 7, paragraph 7-9.

FIGURE 10. PITCHOVER DUE TO TAIL STALL

Icing

CG

Aircraft nose pitches down Weight

c. On some transport turbojets, the tailplane has no ice protection. However, the tailplanes on these aircraft are usually quite thick and therefore, are a less efficient collector of ice. Furthermore, these aircraft are subjected to extensive certification testing and analysis to ensure that the tailplane will not be placed at such an extreme angle in actual operations to experience a stall, even with a large ice accretion.

4-6. PROPELLER ICING. Ice buildup on propeller blades reduces thrust for the same aerodynamic reasons that wings tend to lose lift and increase drag when ice accumulates on them. The greatest quantity of ice normally collects on the spinner and inner radius of the propeller. However, in one suspected large drop icing during a flight test (Figure 11), ice was experienced along the entire span of the propeller blades. This resulted in a 50-knot loss of airspeed in one minute, 25 seconds. There was little airframe ice and no indication of propeller icing. As ice accretes on the propeller blades increasing blade drag, the propeller governor of the constant speed propeller flattens the blade pitch to maintain revolutions per minute (RPM). In the cockpit, the pilot sees no change in RPM or torque.

4-9. EFFECTS OF ICING ON CRITICAL SYSTEMS. › a. Pitot Tube. The pitot tube is particularly vulnerable to icing…

FIGURE 11. PROPELLER ICE ACCRETION DURING AN SLD ENCOUNTER WITH

THE PROPELLER ICE PROTECTION SYSTEM OPERATING

4-7. ANTENNA ICING. Because of their small size and shape, antennas that do not lay flush with the aircraft’s skin tend to accumulate ice rapidly. Furthermore, they often are devoid of an internal anti-icing or deicing capability for protection. During flight in icing conditions, ice accumulations on an antenna may cause it to begin to vibrate or cause radio signals to become distorted. Besides the distraction caused by vibration (pilots who have experienced the vibration describe it as a “howl”), it may cause damage to the antenna. If a frozen antenna breaks off, it can damage other areas of the aircraft in addition to causing a communication or navigation system failure.

4-8. COOLING INLET ICING. Some types of electronic equipment generate significant amounts of heat and require independent sources of cooling, which often use external air scoops. These cooling inlets are susceptible to icing and may or may not be heated as part of the airplane’s icing protection system. Pilots should check their airplane’s AFM to determine if the cooling inlets are protected from ice.

4-9. EFFECTS OF ICING ON CRITICAL SYSTEMS.

a. Pitot Tube. The pitot tube is particularly vulnerable to icing because even light icing can block the entry hole of the pitot tube where ram air enters the system. This will affect the airspeed indicator and is the reason most airplanes are equipped with a pitot heating system. The pitot heater usually consists of coiled wire heating elements wrapped around the air entry tube. If the pitot tube becomes blocked, and its associated drain hole remains clear, ram air no longer is able to enter the pitot system. Air already in the system will vent through the drain hole, and the remaining will drop to ambient (outside) pressure. Under these circumstances, the airspeed indicator reading decreases to zero, because the airspeed indicator senses no difference between ram and static air pressure. If the pitot tube, drain hole, and static system all become blocked in flight changes in airspeed will not be indicated, due to the trapped pressures. However, if the static system remains clear, the airspeed indicator would display a higher-than actual airspeed. At lower altitudes, the airspeed indicator would display a lower-than-actual airspeed.

d. Windshields. › (1) Antiicing generally is provided to enable the flightcrew to see…

b. Static Port. Many aircraft also have a heating system to protect the static ports to ensure the entire pitot-static system is clear of ice. If the static port becomes blocked, the airspeed indicator would still function; however, it would be inaccurate. At altitudes above where the static port became blocked, the airspeed indicator would indicate a lower-than-actual airspeed. At lower altitudes, the airspeed indicator would display a higher-than-actual airspeed. The trapped air in the static system would cause the altimeter to remain at the altitude where the blockage occurred. The vertical speed indicator would remain at zero. On some aircraft, an alternate static air source valve is used for emergencies. If the alternate source is vented inside the airplane, where static pressure is usually lower than outside static pressure, selection of the alternate source may result in the following erroneous instrument indications:

(1) The altimeter reads higher than normal,

(2) The indicated airspeed reads greater than normal,

(3) The vertical-speed indicator momentarily shows a climb.

c. Stall Warning Systems.

(1) Stall warning systems provide essential information to pilots. A loss of these systems can exacerbate an already hazardous situation. These systems range from a sophisticated stall warning vane to a simple stall warning switch. The stall-warning vane (also called an “AOA sensor” since it is a part of the stall warning system) can be found on many aircraft. The AOA provides flightcrews with an AOA display or feeds AOA data to computers that interpret this information and provide stall warning to the crew when the AOA becomes excessive. These devices consist of a vane, which is wedge-like in shape and has freedom to rotate about a horizontal axis, and is connected to a transducer that converts the vane’s movements into electrical signals transmitted to the airplane’s flight data computer. Normally, the vane is heated electrically to prevent ice formation. The transducer is also heated to prevent moisture from condensing on it when the vane heater is operating. If the vane collects ice, it may send erroneous signals to such equipment as stick shakers or stall warning devices. Aircraft that use a stall horn may not give any indication of stall if the stall indicator opening or switch becomes frozen.

(2) Because contamination of the wing reduces lift, even an operational, ice-free stall warning system may be ineffective because the wing will stall at a lower angle of attack due to ice on the airfoil. The stall onset will therefore occur prior to activation of the stall warning devices, leading to a potential pitch or roll upset. It is imperative that pilots monitor airspeed closely when in icing conditions. On airplanes recently certificated for icing conditions, stall warning systems may have been demonstrated to provide adequate warning within the icing conditions required for certification (part 25, appendix C) once certain ice protection systems were activated. However, the adequacy of stall warning systems in conditions outside appendix C, such as SLD, has not been demonstrated.

d. Windshields.

(1) Anti-icing generally is provided to enable the flightcrew to see outside the aircraft in case icing is encountered in flight. On high-performance aircraft that require complex

a. What is Covered. › (1) The icing envelopes are mainly based on various types of stratus…

windshields to protect against bird strikes and withstand pressurization loads, the heating element often is a layer of conductive film or thin wire strands through which electric current is run to heat the windshield and prevent ice from forming.

(2) Aircraft that operate at lower altitudes and lower speeds generally have other systems of window anti-icing/deicing. One system consists of an electrically heated plate installed onto the airplane’s windshield to give the pilot a narrow band of clear visibility. Another system uses a bar at the lower end of the windshield to spray deicing fluid onto it and prevent ice from forming.

e. EPR Probe (turbine engines).

(1) Ice crystals can clog and freeze over turbine engine pressure ratio (EPR) probes as well, resulting in unreliable and misleading power indications. These indications may lead a pilot to believe that an engine is producing more or less power than it actually is, and may result in improper throttle adjustments.

(2) There have been several instances where EPR probes became clogged with ice crystals during climb or cruise (see Air Florida accident in appendix 1. Pilots of turbojet aircraft should calculate a backup N1 setting for takeoff/go-around in icing conditions as a crosscheck for EPR. In flight actuating engine nacelle anti-ice when in heavy clouds usually prevents ice blockage.

f. TAT Probe.

(1) Ice crystals can clog and freeze over the TAT probe on some aircraft. This tendency to freeze over appears to be sensitive to the location of the probe on the airframe. If the TAT freezes over, the indicated temperature will erroneously rise to zero degrees C and hold. In this situation, some aircraft systems will alert the flightcrew that there is a disagreement between various ambient temperature sensors, thus indicating the presence of ice crystals.

(2) Freezing of the TAT probe has been a precursor in many of the turbine engine power loss events occurring in the area of convective weather systems.

4-10. CERTIFICATION FOR FLIGHT IN ICING CONDITIONS. An aircraft which is “certificated for flight in icing conditions” goes through an extensive procedure intended to ensure that it can safely operate throughout those icing conditions encompassed by the icing envelopes specified in 14 CFR part 25, appendix C. This process typically includes extensive analysis (done today with sophisticated computer modeling), tunnel testing, dry-air testing, testing behind an icing tanker, and flight in natural icing conditions. Its objective is not only to verify that the aircraft has functioning ice protection, but also to verify that the aircraft will have acceptable performance and handling qualities in all the environmental conditions covered by the icing envelopes.

a. What is Covered.

(1) The icing envelopes are mainly based on various types of stratus and cumulus supercooled clouds. The envelopes specify maximum amounts of liquid water and drop sizes

4-11. SIGNIFICANCE OF ICING CERTIFICATION. › c. Prior to 1973, small airplanes were approved for flight in icing if…

expected at certain temperatures and altitude ranges. The envelopes were formulated during the 1950s, based on contemporary research, and research that is more recent generally is consistent with the envelopes.

(2) It has been estimated that these envelopes encompass 99.9 percent of all conditions encountered in research programs in stratus and cumulus clouds.

b. What is Not Covered.

(1) First, the pilot should bear in mind that 99.9 percent is not 100 percent, and so vigilance in exceptional conditions is always wise.

(2) Second, the cloud measurements on which the envelopes were based generally did not include SLD conditions. Recent research shows that SLD (in particular, freezing drizzle aloft within cloud) is more common in supercooled clouds than had been thought (see Table 1 for some cues of SLD conditions).

(3) Third, freezing rain or freezing drizzle may be encountered beneath the clouds. Neither of these icing conditions is included in the icing envelopes.

(4) Finally, ice crystals may be encountered in high concentrations at higher altitudes in the area of convective weather systems. Currently these conditions are not included in the icing envelopes, although new envelopes have been preliminarily developed.

4-11. SIGNIFICANCE OF ICING CERTIFICATION.

a. Icing certification is an extensive process. It includes testing and analysis to check that aircraft can operate safely for extended periods in the conditions covered by the icing envelopes. For example, certification includes testing and analysis to show that an aircraft can hold in significant icing conditions for up to 45 minutes. Nonetheless, pilots of certificated aircraft should not be casual about operations in icing conditions, particularly extended operations. It is always possible to encounter an unusual condition for which the aircraft has not been certificated, such as liquid water content outside the envelopes, which is sometimes indicated by a very rapid rate of accumulation. This can result in runback and ice accumulation aft of protected surfaces.

b. SLD may result in droplets impinging aft of protected surfaces and causing ice accumulation. These surfaces may be very effective ice collectors, and ice accumulations may persist as long as the aircraft remains in icing conditions. Note also that icing conditions can develop very quickly and may not be immediately recognized. For example, even though the rate of accumulation may be quite gradual, a thin, extremely rough accretion can develop on a critical surface in minutes. This can be very hazardous, particularly on approach and landing.

NOTE: Not all icing certification is the same.

c. Prior to 1973, small airplanes were approved for flight in icing if they were equipped with a minimum suite of ice protection equipment. For example, see Bureau of Flight Standards

4-11. SIGNIFICANCE OF ICING CERTIFICATION. › f. Keep in mind, even though the small airplane icing certification…

Release 434. No analysis or testing to show safe operation in the part 25, appendix C icing envelopes was required.

d. Many small airplanes flying today fall in this category. In 1973, at Amendment 23-14, 14 CFR part 23, § 23.1419 was amended to require analysis and testing to demonstrate that the airplane can operate safely in the part 25, appendix C icing envelopes.

e. In 1993, at Amendment 23-43, § 23.1419 was amended to require small airplanes, certificated for known icing, to comply with performance, stability, controllability, and maneuverability regulations in icing. There were no quantitative criteria for performance prior to Amendment 23-43.

f. Keep in mind, even though the small airplane icing certification regulations changed in 1973 and 1993, the means of showing compliance have changed continuously, as shown by the example in Table 1. Table 1 compares the current means of compliance in AC 23.1419-2C (2004) to the guidance that existed prior to 1993.

TABLE 1. EVOLUTION OF ICING CERTIFICATION STANDARDS

Criteria prior to 1993 Current Criteria

Simulated ice shapes tested

Unprotected areas only Unprotected and protected (e.g., intercycle ice on boots)

Performance criteria

Qualitative Must meet Subpart B minimum climb gradients

Stall warning Can use different type in icing (e.g., buffet versus stall warning system)

Stall warning type in icing should be same as in non-icing and margin should meet Subpart B

Maneuver margin No policy There should be no buffet or stall warning during maneuvering at operating airspeeds

Autopilot No policy Evaluate operation, disconnect at stall warning

Propeller icing performance

No policy Evaluate performance in natural icing

Use of ice adhesion inhibitors

No policy Cannot use for certification

4-1. FORMS OF ICING. › 4-13. ANTIICING SYSTEMS.

g. How can I tell how my airplane was certificated for icing?

(1) The airplane was certificated to 14 CFR § 23.1419 at Amendment 23-14 or later if your AFM or POH references “part 25, appendix C” icing conditions, or “14 CFR § 23.1419” at Amendment 23-14 or later.

(2) The “Certification Basis” section of your airplane’s type certification data sheet (TCDS) may reference “14 CFR § 23.1419” at Amendment 23-14 or higher, or “SFAR 23.” The TCDS can be found in the FAA’s on-line Regulatory and Guidance Library at http://rgl.faa.gov.

(3) If there is only a minimum equipment list (MEL) for icing conditions in the AFM or POH, the certification basis of your airplane is prior to Amendment 23-14 (1973). Some pilots mistakenly believe IFR certificated airplanes are analyzed or tested for inadvertent icing encounters—they are not.

h. How is certification related to the operating rules?

(1) Section 34 of Special Federal Aviation Regulation (SFAR) 23, and § 34 of part 135, appendix A.

(2) These are referenced in the part 91 and part 135 operating rules, respectively, and are equivalent to 14 CFR § 23.1419 at Amendment 23-14.

4-12. ICE PROTECTION EQUIPMENT ON AIRPLANES NOT CERTIFICATED FOR ICING.

a. All aircraft are required to have ice protection for their propulsion systems in case of an inadvertent icing encounter, and nearly all aircraft have pitot heat and an alternate source of static air.

b. Some general aviation aircraft, that are not certificated for flight in icing conditions, also have ice protection systems on their wings and tailplane, providing an additional safety margin should an inadvertent encounter with icing occur. These systems are for emergency use only.

c. The FAA recommends that aircraft not certificated for flight in icing conditions, but that are equipped with these “non-hazard” deicing/anti-icing equipment exit those conditions as expeditiously as possible, coordinating with ATC as necessary.

d. The differences between these systems and fully certified systems are significant. Airplane performance is unknown, stall warning in icing conditions most likely will not activate prior to stall, controls may jam due to ice accretion, and system features required for known icing may not be present in these “non-hazard” systems.

4-13. ANTI-ICING SYSTEMS. Anti-icing systems operate on the principle that ice should not be allowed to accumulate on the aircraft or certain aircraft systems when flying through icing conditions. Usually, anti-icing is accomplished using electric heat, hot air, or chemicals. While an aircraft’s AFM or POH is the ultimate authority on the operation of anti-icing systems, a good

4-14. DEICING SYSTEMS. › a. The operating philosophy behind deicing systems differ from that of…

rule of thumb is to activate anti-icing systems at the first signs of visible moisture encountered during conditions conducive to icing. This will prevent the buildup of any appreciable amounts of ice.

a. Electric Systems. Electric systems normally are used for smaller areas such as antennas, static ports, air temperature probes, pitot tubes, and windshields.

b. Hot Air Systems.

(1) Hot air systems are used for larger areas of the aircraft, such as engine nacelles and wing leading edges. Bleed air from turbine engines is the most common type of anti-icing protection for engine nacelles and wings of transport and business turbojets. Hot air is distributed to “piccolo tubes,” which consist of a perforated pipe installed directly behind the airplane’s skin. Such hot-air systems are quite effective in preventing the formation of ice.

(2) One drawback of a hot air system is that tapping air from the engine to anti-ice large surfaces reduces the amount of available thrust, which may have a significant effect on climb performance (especially one engine inoperative climb performance in multiengine turboprops, turbojets, and turbofans.) This performance loss is the reason this system is not common on smaller turbine powered airplanes.

(3) Pilots should keep in mind that while cruising or descending with anti-ice systems on, higher than normal power settings may be required to ensure sufficient bleed air is being supplied to the anti-ice system, and to prevent engine surges/stalls (see the particular AFM for the appropriate settings.)

(4) In addition, in some situations on some airplanes, the hot air system may not fully evaporate all impinging water drops, resulting in runback ice. This may occur with an inoperative engine, and may be the reason your AFM requires a minimum engine power setting on descent.

c. Chemical Systems.

(1) Chemical systems apply a chemical agent that lowers the freezing point of water found on aircraft surfaces and decreases the friction coefficient of those surfaces to prevent ice from adhering to the surfaces. Examples of such chemical agents are isopropyl alcohol and ethylene glycol.

(2) While an aircraft’s AFM or POH is the ultimate authority on the operation of anti-icing systems, a good rule of thumb is to activate anti-icing systems at the first signs of visible moisture encountered during conditions conductive to icing. This will prevent the buildup of any appreciable amounts of ice.

4-14. DEICING SYSTEMS.

a. The operating philosophy behind deicing systems differ from that of anti-icing systems because deicing systems permit a certain amount of ice accumulation before they can be activated. Because ice is permitted to accrete between cycles, and because after each cycle there

d. Electrothermal System. › (2) Propellers are deiced using rubber boots with embedded heater wires…

is some residual ice, the wing or the tailplane is never entirely “clean.” If the systems are operated properly, however, the intercycle ice buildup on the airfoil should be limited, along with the accompanying drag increases.

b. Because other parts of the aircraft, including part of the span of the wing, are not protected from ice, a drag increase from those areas will still be present. This is accounted for in the icing certification process, and the pilot can fly the aircraft safely by following the operating procedures in the AFM or POH. Residual ice and the ice that accumulates between deicing cycles can be expected to have some effect on CLmax, but note that this effect is significant only at higher AOA.

(1) At the AOA typical of cruise, this ice should have very little effect on lift. At the higher AOA characteristic of approach and landing, the decrease in CLmax will translate into an increase in stall speed. Thus, the pilot should cycle the deicing system on approach after exiting the icing conditions so that the wing will be as clean as possible and any effect on stall speed minimized.

(2) If the icing conditions cannot be exited until late in the approach, or if significant icing appears to remain on the wing after cycling the system, the pilot should assume an increase in the aircraft’s stall speed and adjust the approach speed accordingly. Pilots should consult the AFM or POH for guidance. Usually, deicing is accomplished using an electroimpact system, an electrothermal system, or a pneumatic boot system.

c. Electroimpact System.

(1) The electroimpact system deices a surface using pulses of energy to produce rapid flexing movements of the airplane’s skin surface, which break the bond of accumulated ice.

(2) The shattered ice is then carried away by the airflow.

d. Electrothermal System.

(1) The electrothermal system deices a surface by heating the surface to a temperature above freezing to break the bond of accumulated ice. The shattered ice is then carried away by the airflow. The surface is allowed to cool to allow ice to form, and the heat is activated again to shed the ice, the cycle being repeated. Such systems are common on propellers and helicopter main rotors, and have been recently introduced on wing and tail leading edges.

(2) Propellers are deiced using rubber boots with embedded heater wires to break the adhesion of ice to the propeller blades. Sometimes the blades are heated alternately in sections due to limits of available electrical power. The alternate sections are heated symmetrically to avoid an imbalance of the propeller while sections of ice are being removed and dislodged from the propeller by centrifugal force. Often, on aircraft that have such systems, the skin surrounding the airframe is reinforced with doublers to strengthen the skin where ice is most likely to be flung from the propellers. However, the initial imbalance caused by ice accumulation and the loud noise created by ice shedding and hitting the airframe can be unsettling to passengers and distracting to flightcrews.

e. Pneumatic Boots. › (4) Depending on the icing conditions and airspeed, it could take…

e. Pneumatic Boots.

(1) Pneumatic boots, pictured in Figure 12, consist of rubber tubes attached to critical aircraft surfaces, such as the leading edges of wings and horizontal and vertical stabilizers. The tubes may be either chordwise or spanwise. The pneumatic boots are collapsed during normal operations, with suction provided by a vacuum pump to avoid disruption of airflow over the wings. When the system is activated in flight, a timer-operated valve selectively inflates all tubes or half of the tubes intermittently to crack the ice and then allow the airflow over the wings to blow off the broken ice.

(2) A traditional concern in the operation of pneumatic boots has been “ice bridging.” This is attributed to the formation of a thin layer of ice, which is sufficiently plastic to deform to the shape of an expanded deicing boot without being fractured or shed during the ensuing tube deflation. As the deformed ice hardens and accretes additional ice, the boot may be ineffective in shedding the “bridge” of ice. Traditional advice on avoiding this problem has been to wait for a layer of ice of a predetermined thickness to form before cycling the boot. This thickness has been variously prescribed as 1/4 inch, 1/2 inch, and even 1 inch.

(3) Studies done in the late 1990’s have established that there are few, if any, documented cases of ice bridging on modern boot designs. In addition, several icing tunnel tests sponsored by the FAA since 1999 showed no ice bridging on modern boot designs. Known cases are confined to boots of designs dating back a quarter century or more. Furthermore, it is recognized that a layer of ice 1/2 inch thick, especially if rough, can have a significant effect on aircraft performance, stability, and control. Consequently, some manufacturers now advise that the boots be cycled as soon as icing is encountered, rather than waiting for a prescribed thickness to accrete. More recent studies in 2005 have shown that at airspeeds typical of general aviation airplanes with modern boot designs, ice will not shed at every boot inflation.

(4) Depending on the icing conditions and airspeed, it could take anywhere from 4 to 25 minutes to shed ice (perhaps longer at the extremely cold temperature of -30°C (-22°F), even when boots were activated at the first sign of icing and cycled every minute thereafter. Cycling early and often provided a small improvement over waiting until 1/4 or 1/2 inch of ice has accreted before activating the boots. Residual and intercycle ice are inherent in the use of any available deicing system, including pneumatic boots. Proper operation of the boots is necessary to minimize the effect of this ice. It is essential that the pilot consult the AFM or POH (the POH must be consistent with the operating limitations section of the AFM) for guidance on proper use of the system. The 2005 testing did show that the proper application of ice adhesion inhibitors improved ice shedding at colder temperatures. The FAA strongly encourages the use of the manufacturer’s recommended ice adhesion inhibitors.

a. Electronic. › (1) Many modern aircraft come equipped with electronic ice detectors.

FIGURE 12. WING BOOT

All Tubes Deflated

All Tubes Inflated

4-15. MAINTENANCE CONSIDERATIONS. Some anti-icing and deicing systems are known to be very reliable, while others may require a lot of maintenance to remain effective. Pneumatic boots, for example, are known for their susceptibility to damage from many sources and should be inspected carefully. The rubber used for the boots is subject to degradation from atmospheric pollution, which results in the rubber cracking and losing some of its elastic properties. An ice adhesion inhibitor should be applied to pneumatic deicing boots in accordance with the maintenance manual. Any product that is not recommended by the airplane or boot manufacturer should be approved by the FAA. Other problems are defects, delaminations, or tears in the rubber caused by the impact of objects, such as foreign matter found on airport ramps. Pinholes or tears in pneumatic deicing boots will draw in moisture when system vacuum is supplied, and subsequent freezing of this moisture can render the system ineffective. Pilots should have maintenance personnel evaluate any defects in the boots when they are found.

(1) Flightcrews always should ensure their airplane’s anti-icing and deicing equipment is in a serviceable condition.

(2) The airplane’s MEL should be consulted for details on what is permitted to be inoperable and what equipment deficiencies constitute “no go” items.

4-16. ICE DETECTION.

a. Electronic.

(1) Many modern aircraft come equipped with electronic ice detectors. A common in-flight ice detector consists of a probe that vibrates at a specific frequency. When ice begins to form on the probe, the frequency of the probe’s vibration will change because of the increased mass of ice on the probe, and an indicator will light in the cockpit. These detectors are activated for a short time period, generally one minute, after which the probe is heated electrically to melt the accreted ice. The process is then repeated. If the aircraft is flying in continued icing conditions, ice will continue to form on the probe, and the light in the cockpit will remain on.

4-17. VISUAL CLUES OF SLD CONDITIONS. › c. Unheated portions of side windows may begin to accumulate granular…

(2) Pilots should consult their AFM or POH to determine if their ice detection system is an “Advisory” or “Primary” system. The difference between the systems is the redundancy of the system and testing required for certification. The majority of airplanes have an “Advisory” system, which means the pilot is responsible for detecting ice and ensuring ice protection systems are activated. This is true even for ice protection systems that are automatically activated when the ice detection system detects ice.

(3) Currently, there are no electronic detection systems that can reliably detect ice crystals, although new systems are under development.

b. Visual. Strategically located protuberances also may serve as ice indicators. There is usually some unprotected protuberance or surface visible to the crew, such as windshield wipers, pod pylons, or landing lights that can serve as an icing reference because they tend to build up ice first. If there is no such protuberance visible to the crew, manufacturers may provide one for this purpose. These ice detectors, referred to as “ice evidence probes,” are typically in plain view of the cockpit and normally collect ice more readily than larger components or surfaces. If ice begins to accumulate on such an ice detector, the flightcrew should assume the rest of the aircraft also is accumulating ice and take appropriate action. These detectors only serve their purpose if pilots include them in their scan during flight in potential icing conditions. Pilots should monitor critical surfaces at temperatures near freezing, since ice may form on critical surfaces prior to forming on visual ice indicators.

4-17. VISUAL CLUES OF SLD CONDITIONS. If SLD is known to be present, most aircraft with unpowered controls and airframe deicing systems should request a route or altitude change to exit the conditions. This action may be prudent for other aircraft as well. The cues listed below were developed for aircraft with unpowered controls and pneumatic deicing boots as indicative of SLD conditions. Of most concern is the accretion of ice in areas aft of where it would usually be found. Such “aft accretions” could sometimes be the result of runback due to high liquid water rather than SLD. Excessive runback icing, however, may have effects similar to SLD, so similar pilot action may be appropriate. The cues are:

a. Ice may become visible on the upper or lower surface of the wing, aft of the active part of the deicing boots. Pilots should look for irregular or jagged lines of ice or for pieces of ice shedding off the airplane. During night operations, adequate illumination should be used to observe all areas. On most airplanes, the last inch of the deicing boot is inactive.

b. The aft limit of ice accumulation on a propeller spinner that is not heated will reveal ice extending beyond normal limits, typically back to the blades.

c. Unheated portions of side windows may begin to accumulate granular dispersed ice crystals or a translucent or opaque coating over the entire window. This icing may be accompanied by other ice patterns on the windows, such as ridges. These patterns may occur from within a few seconds to half a minute after exposure to SLD conditions.

d. Ice coverage may become unusually extensive, with visible ice fingers or feathers on parts of the airframe that normally would not be covered by ice. The aircraft’s performance may

c. Unheated portions of side windows may begin to accumulate granular… › (2) While the pilot should be aware of these general cues, there may be…

Par 4-17 Page 33 (and 34)

degrade. Pilots should remain vigilant when icing conditions are present, and any alteration of the aircraft’s performance should be monitored closely as a sign of icing on the airplane.

NOTE: Pilots should be vigilant for the ice accretions listed above when the following are observed:

• Visible rain or drizzle at temperatures below +5°C outside air temperature (OAT).

• Droplets that splash or splatter on impact at temperatures below +5°C OAT.

(1) Vigilance for SLD ice accretions should also be exercised when flying into or over areas reporting precipitation at the surface, such as rain, freezing rain, sleet, ice pellets, drizzle, freezing drizzle, or snow, where temperatures are near freezing. However, pilots should be aware that SLD could occur aloft without any SLD precipitation on the surface. Current weather information can miss SLD, so it is important to know and watch for cues on the airplane.

(2) While the pilot should be aware of these general cues, there may be specific cues that are characteristic of SLD icing on particular aircraft types. The pilot should consult the aircraft AFM or POH for descriptions of any such cues.

CHAPTER 5. FLIGHT PLANNING

This chapter describes sources of flight planning information as well as elements pilots can identify from the material made available to them to adequately manage their in-flight icing risk.

5-3. PIREPs. › c. To report the intensity of icing in a PIREP, the following…

5-1. GENERAL AVIATION RESOURCES.

a. The primary means available to general aviation pilots for obtaining preflight planning information is the FSS. An FSS briefer is available via telephone by dialing 1-800-WX-BRIEF (1-800-992-7433). The briefer will provide weather information that may include the location of frontal systems, available PIREPs, cloud coverage, temperatures, and wind direction and speed.

b. Another source of information is the Direct User Access Terminal (DUAT), which is an information system that enables pilots to conduct their own weather briefings. The computer-based system acquires and stores a number of NWS and FAA products commonly used in pilot weather briefings and can be accessed through the World Wide Web. Pilots also can file and amend flight plans while logged into the system. Further information about DUAT can be obtained from any FSS, Flight Standards District Office (FSDO), or on the Web.

5-2. AIR CARRIER DISPATCH SERVICES.

a. U.S. air carriers that are authorized to conduct domestic or flag operations must have professional dispatch services that provide their pilots with relevant weather data for each flight.

b. Sometimes, these dispatchers rely on forecasts developed by the NWS, but some air carriers have an expanded capability, with their own meteorologists on staff who analyze raw data in addition to available forecasts to build a more detailed picture of existing and predicted weather conditions, including icing conditions.

NOTE: Title 14 CFR part 121 supplemental and part 135 commuter/on-demand operations do not require dispatchers.

5-3. PIREPs.

a. PIREPs are the only direct evidence of aircraft icing in a given area. They constitute an extremely valuable source of information for flight planning.

b. The AIM lists the following essential elements for all PIREPs: message type, location, time, flight level, type of aircraft, and at least one weather element encountered. When not required, elements without reported data are omitted. All altitudes are referenced to mean sea level unless otherwise noted. Distances are in nautical miles and time is in Coordinated Universal Time. The phenomenon is coded in contractions and symbols. A PIREP usually is transmitted as an individual report but can be appended to a surface aviation weather report or placed into groups of PIREPs.

c. To report the intensity of icing in a PIREP, the following descriptions should be used (refer to Chapter 2 for complete definitions.):

5-4. PIREP CAUTIONS. › c. Again, there are several possible reasons for this.

(1) Trace Icing. Ice becomes noticeable. The rate of accumulation is slightly greater than the rate of sublimation. A representative accretion rate for reference purposes is less than 1/4 inch (6 mm) per hour on the outer wing. The pilot should consider exiting the icing conditions before they become worse.

(2) Light Icing. The rate of ice accumulation requires occasional cycling of manual deicing systems to minimize ice accretions on the airframe. A representative accretion rate for reference purposes is 1⁄4 inch to 1 inch (0.6 to 2.5 cm) per hour on the outer wing. The pilot should consider exiting the condition.

(3) Moderate Icing. The rate of ice accumulation requires frequent cycling of manual deicing systems to minimize ice accretions on the airframe. A representative accretion rate for reference purposes is 1 to 3 inches (2.5 to 7.5 cm) per hour on the outer wing. The pilot should consider exiting the condition as soon as possible.

(4) Heavy Icing. The rate of ice accumulation requires maximum use of the ice protection systems to minimize ice accretions on the airframe. A representative accretion rate for reference purposes is more than 3 inches (7.5 cm) per hour on the outer wing. Immediate exit from the conditions should be considered.

(5) Severe Icing. The rate of ice accumulation is such that ice protection systems fail to remove the accumulation of ice and ice accumulates in locations not normally prone to icing, such as areas aft of protected surfaces and areas identified by the manufacturer. Immediate exit from the condition is necessary.

5-4. PIREP CAUTIONS. Although PIREPs are excellent sources of information on in-flight icing, there are situations when these reports can be misleading. Two possibilities are discussed below.

a. An aircraft encounters icing conditions in an area where there were no recent icing PIREPs. There are several possible reasons for this:

(1) No aircraft recently flew in the area.

(2) Some aircraft recently flew in the area but did not encounter the icing conditions. This is a common occurrence, especially if the area has limited air traffic. Icing conditions are extremely variable in both space and time. A slight change in altitude or flightpath or the passage of just a few minutes can mean the difference between encountering and not encountering icing. There are many documented cases of aircraft flying through approximately the same area at similar altitudes at approximately the same time with one aircraft experiencing substantial icing and the other experiencing none.

b. An aircraft encountered icing, but the pilot did not report it. An aircraft encounters icing conditions that are more serious than those are reported in any recent PIREPs in the given area.

c. Again, there are several possible reasons for this.

5-6. TERMINOLOGY USED IN ICING FORECASTS. › a. The AWC uses the same terms for icing intensity in its forecasts as…

(1) Icing conditions are extremely variable in space and time, as previously noted. PIREPs depend on the type and ice protection of the reporting aircraft. If the pilot’s aircraft is smaller, has less power, or has less ice protection than the reporting aircraft, it may experience more serious icing than the reporting aircraft in the same exact meteorological conditions. For example, a Boeing 747 may report light icing when flying through conditions that would cause a Mooney to experience severe icing.

(2) PIREPs are subjective, depending on the pilot’s observations, how the pilot operates the ice protection on the aircraft, and the pilot’s experience level with in-flight icing. For example, there are documented cases of pilots reporting “light” icing conditions when ice was accreting on an ice evidence probe at a rate of approximately 1 inch per minute. In addition, observation and assessment of icing is more difficult at night.

(3) Although PIREPs from similar aircraft are most relevant to the pilot’s aircraft, direct translation to the pilot’s aircraft may still present difficulties. In addition to pilot subjectivity, other relevant questions are: Was the reporting aircraft flying slowly, or climbing, at a high AOA (which is conducive to accumulation over a larger area of the aircraft)? What kind of ice protection does the reporting aircraft have, and is it functioning properly?

(4) When icing conditions exist, reporting may alert other crews to maintain vigilance. Flightcrews should ensure that when submitting a PIREP of observed icing conditions, they accurately state the conditions and effects of the icing observed and report them in a timely fashion to make the PIREP as useful as possible.

5-5. ICING FORECASTS.

a. Aviation meteorologists at the NWS Aviation Weather Center (AWC), local NWS Field Offices, major airlines, and private companies prepare icing forecasts. In addition, guidance products are available on the Web. Icing AIRMETs, prepared at AWC, cover a 6-hour forecast window and are updated four times daily. Because they cover an extended time and may cover an area of several states, they are necessarily somewhat broad. Consulting a local FSS or NWS for a more specific preflight briefing will provide more detail and allow interaction with the briefer for more specific questions.

b. Technologies for forecasting icing are undergoing rapid development. PIREPs remain the major source of information for icing location and severity. The forecaster matches the PIREP to local weather features, assesses where those features will be moving during the forecast period, and estimates areas of expected icing, assigning their type and severity in this manner. Automated methods for assessing these icing attributes have been developed and are now available. (See the discussion on Current and Forecast Icing Product (CIP and FIP) later in this section.)

5-6. TERMINOLOGY USED IN ICING FORECASTS.

a. The AWC uses the same terms for icing intensity in its forecasts as those given in the AIM for use in PIREPs. These forecasts are based on:

5-7. CURRENT AND FORECAST ICING PRODUCTS (CIP AND FIP). › c. The FIP is an automatically generated forecast of the potential for…

(1) Weather analysis, using both traditional tools and those developed in recent years by the research community.

(2) PIREPs.

b. Since icing intensity is aircraft-dependent, a standard needs to be adopted by the NWS for all icing forecasts. Currently, there is one standard for AIRMET in which light or moderate icing is related to anticipated operational effects on a reciprocating engine, straight wing aircraft of intermediate size. Nevertheless, pilots of other aircraft are expected to familiarize themselves with AIRMETs also. However, there is no similar standard for severe icing in SIGMETs. Therefore, any SIGMET for severe icing must be interpreted as forecasting severe icing for all classes of aircraft.

c. Icing PIREPs are valuable to forecasters for the same reasons they are valuable to pilots. The PIREPs constitute the only direct observation of the phenomenon that is forecast. Thus the weather forecasters carefully evaluate the results of their weather analysis against the PIREPs for the forecast area and modify their forecasts if necessary. SIGMETs for severe icing are rarely issued unless there has been a PIREP of severe icing in the forecast area. PIREPs are also used in the CIP algorithm, described in the next chapter.

d. Icing forecasts also use the previously defined terms clear, rime, and mixed to describe types of ice. A convention that has evolved in forecasting practice is to associate ice type mainly with cloud drop size, essentially ignoring other factors such as temperature, liquid water content, drop size, and aircraft velocity. Thus a forecast of rime icing (RIME ICG) indicates smaller drop sizes, whereas a forecast of mixed (MXD ICG) or clear (CLR ICG) indicates larger drop sizes, with the line of demarcation not firmly established.

5-7. CURRENT AND FORECAST ICING PRODUCTS (CIP AND FIP).

a. There is a new Web-based preflight planning tool available to pilots that gives a graphical presentation of the current and forecast potential for icing. The URL for this product is http://adds.aviationweather.gov/icing/.

b. The CIP represents the latest analysis of possible icing regions. CIP combines weather sensor and numerical model data, as well as PIREPS, to provide a three-dimensional diagnosis of the icing environment.

(1) The new version of CIP output consists of a probability of icing and a severity of icing, as well as an indication of the possible presence of SLD.

(2) Water drops larger than 50 micrometers (diameter), which includes freezing drizzle and freezing rain aloft characterize SLD icing conditions. It has been demonstrated that these conditions, which are outside the icing certification envelopes (part 25, appendix C) can be particularly hazardous to some aircraft. Thus the information can be valuable for flight planning.

c. The FIP is an automatically generated forecast of the potential for icing 2, 3, 6, 9 and 12 hours in the future. This icing potential demonstrates the confidence that an atmospheric location, represented by a three-dimensional model grid box, will contain supercooled liquid

water that is likely to form ice on an aircraft. The algorithm analyzes the model output from a vertical column, determines the cloud top and base heights, checks for embedded cloud layers, and identifies a precipitation type. Once the likely locations of clouds and precipitation are found, the physical icing situation is determined, and a physically-based, fuzzy logic method is used to determine the icing potential. The fuzzy logic interest maps are based on clues from the model output reflecting relevance to the presence of icing. After the information is extracted, the interest maps are combined in a manner that reflects their significance for icing, given the physical situation present. The entire model domain is examined and the result is a three-dimensional depiction of the potential for icing and SLD at the model valid time. Note that plans are for FIP to depict icing probability and severity, similar to CIP, in mid-2008.

5-8. PREFLIGHT PLANNING INFORMATION. › d. AIRMET and SIGMET. An AIRMET is information of significant weather…

5-8. PREFLIGHT PLANNING INFORMATION. All pilots, whether they are general aviation (GA) or air carrier pilots, are responsible for obtaining as much information as possible about all meteorological conditions, including icing conditions, before departure. Some important meteorological facts that pilots should be aware of with respect to icing are described below.

a. Location of Fronts. Fronts play an important part in the formation of icing conditions. Pilots should be aware of a front’s location, type, speed, and direction of movement. Pilots should try to keep a mental picture of where the front is moving and look for indications of frontal activity or frontal passage, such as a wind shift or temperature change.

b. Cloud Layers. While information on the types of clouds present may not be available without direct observation, the bases and tops of clouds might be known. This information is valuable because pilots need to know whether they will be able to climb above the icing layers of the clouds or descend beneath those layers into warmer air if icing is encountered.

c. Freezing Levels. It is critically important for pilots to obtain the freezing levels for the areas in which they will be flying to be able to make educated decisions on how to exit icing conditions if they are encountered. It is also important for pilots to know if there are any temperature inversions aloft that might alter the normal relationship between altitude and air temperature. Pilots should be aware of multiple freezing levels and their locations. The National Weather Service Aviation Digital Data Service (ADDS) Web site at http://adds.aviationweather.gov/icing/ provides a graphical depiction of the freezing level.

d. AIRMET and SIGMET. An AIRMET is information of significant weather phenomena, but describes conditions at intensities lower than those described that trigger a SIGMET. An AIRMET is intended for dissemination to all pilots in the preflight and en route phase of flight.

• SIGMETs and Convective SIGMETs advise of weather that is potentially hazardous for all aircraft, such as severe icing. A SIGMET for severe icing applies to all aircraft, from small GA aircraft to transport jets (see also the discussion in paragraph 5-6, Terminology Used in Icing Forecasts).

• The ADDS Web site at http://adds.aviationweather.gov/airmets provides a graphical depiction of the areas covered by AIRMETS and SIGMETS.

Continue reading ↓ 120 of 232 passages shown