AC 65-9A [Large AC] Airframe and Powerplant Mechanics General Handbook
This document is cancelled. It may have been replaced. Check the official source before relying on it.
AC65-9A
Airframe 4 Powerplant
MECHANICS
GENERAL HANDBOOK
CONSOLIDATED
REPRINT (includes CHG 1, dated 3/31/99)
U.S. DEPARTMENT OF TRANSPORTATION
. " :.,,-~-=~-'" -~-----"===---'--.'\,i/
AIRFRAME AND POWERPLANT
MECHANICS
GENERAL HANDBOOK
U.S. DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION
FEDERAL AVIATION ADMINISTRATION
Flight Standards Service
First Edition 1970
First Revision 1976
For sale by the U.S. Government Printing Office Superintendent of Documents, Mail Stop: SSOP, Washington, DC 20402-9328
. :~\
PREFACE
This handbook was developed and first printed in 1970 as one of a series of three handbooks for persons preparing for mechanic certification with airframe or powerplant ratings, or both. It is intended that this handbook will provide basic information on principles, fundam€ntals, and technical procedures in the subject matter areas common to both the airframe and powerplant ratings. Emphasis in this volume is on theory and methods of application.
The handbook is designed to aid Students enrolled in a formal course_of instruction as well as the individual who is studying on his own. Since the knowledge requirements for the airframe and powerplant ratings closely parallel each other in some subject areas, the chapters which discuss fire protection systems and electrical systems contain some material which is also duplicated in the Airframe and Power-
plant Mechanics Powerplant Handbook, AC 65-12A, and the Airframe and Powerplant Mechanics Airframe Handbook, AC 65-ISA.
This volume contains information on aircraft ·drawings, weight and balance, aircraft materials and processesi physics, electricity, inspection, ground support, and tools. Knowledge gained from the study of this handbook is essential before proceeding in a course of study in either the airframe or powerplant handbooks.
Because there are so many diffrrent types of airframes and powerplants in use today, it is reasonable to expect that differences exist in the components and systems of each. To avoid undue repetition, the practice of using representative systems and units is carried out throughout the handbook. Subject matter treatment is from a generalize-cl point of view~ and should be supplemented by reference to manufacturers' manuals or other textbooks if more detail is desired. This handbook is not intended to repiace, substitute for, or supersede official regulations or the manufacturers' instructions.
Grateful acknowledgement is extended to the manufacturers of airframe and airframe components for their cooperation in making material available for inclusion.
Copyright material is used by special permission of the following organizations and may not be extracted or reproduced without permission of the copyright owner.
Monsanto Chemical Skvdrol ® Fluids Townsend Corporation Ch.erry Rivets
J. 0. King, Inc. Gravines. Inc. Walter Kidde DuPont DeNemours National Fire Protection
Association National Association of
Fire Extinguisher Distributors Flight Safety Foundation American Petroleum Institute Exxon Parker Hannifin
Acres Sleeves Acres Sleeves
Fire Extinguishers Fire Extinguishers Fire Extinguishants Fire Extinguisher and
Extinguishant Specifications
Fire Extinguishers Refueling Data Aviation Fuels A\'iation Fuels Aircraft Fittings
The advancements in aeronautical technology dictate that an instructional handbook must be under continuous review and brought up to date periodicaliy to be valid. Flight Standards requested comments. from the cntificatE'<l aviation maintenance technician schools, on the three handbooks. As a result of this survey, the handbooks have beE'n updated to this extent: nE'w matPrial has been added in the areas which ·were indicated as being deficient, and some material has been real'ranged to improve the teachability of the handbooks.
iii
We would appreciate having errors brought to our attention, as well as receiving suggestions for improving the- usefulness of the handbooks. Comments and suggestions will be retained in our files until such time as the next revision will be accomplished.
Address all correspondence relating to these handbooks to:
U.S. Department of Transportation Federal Aviation Administration F1ight Standards National Field Office P.O. Box 25082 Oklahoma City, Oklahoma 73125
The companion handbooks to AC 65-9A are the Airframe and Powerplant Mechanics Powerplant Handbook, AC 65-12A, and the Airframe an-d Powerplant Me· chanics Airframe Handbook, AC 65-lSA.
iv
-~ ~·--""-~-·-==~-~~~~-'?<1."_:,c ..,,-.. ',;·-·
CONTENTS
PREFACE- … iii CONTENTS … V CHAPTER L MATHEMATICS
PREFACE- … iii CONTENTS … V CHAPTER L MATHEMATICS
Introduction … ~----------------------------------- 1 Whole Numhers … 1 Fractions … 2 Mixed Numbers … --- … 4 Decimals ------------------- … -------------- … 5 Ratio--------------------------------------------------------- 10 Proportion … 11 Positive and Negative Numbers … 11 Powers and Roots … - … 12 Computing Area … … 15 Computing the Volume of Solids … 20 Graphs and Charts … 23 _!\!Ieasurement Systems … ----------- ____ ------------------- 27 Functions of Numbers ------------------------------------------- 31 CHAPTER 2. AIRCRAFT DRAWINGS Prints … 35 Working Drawings … ------------ … ----------- __ 35 Care and Use of Drawings … -.- … 36 Title Blocks … 36 Bill of Material … - ___ - ___ - ___ - - 37 Other Data---------------------------------------------------- 38 Methods of Illustrating Objects … 39 Meaning of Lines … … 42 Reading Drawings … 45 Diagrams … … 46 Drawing Sketches … 49 Drawing Symbols … 50 Care of Drafting Instruments … ----------- ---------------- 50 Microfihn … 50
CHAPTER 3. AIRCRAFT WEIGHT AND BALANCE Purpose … 53 "".- .··•
CHAPTER 3. AIRCRAFT WEIGHT AND BALANCE Purpose … 53 "".- .··•
Need for Reweighing … 53 Theory of Weight and Balance … 53 Mathematical Proof … 54 Weight and Balance Data … 54 Terminology … 54 Aircraft Weighing Procedure … 59 Weight and Balance Extreme Conditions … 65 Installation of Ballast … 67
V
'
,·
Loading Graphs and C. G. Envelopes … 69 Electronic Weighing Equipment … 70 Helicopter Weight and Balance … 70 CHAPTER 4. FUELS AND FUEL SYSTEMS General … 73 Characteristics and Properties of Aviation Gasoline … 73 Turbine Engine Fuels … 77 Fuel System Contamination … 78 Fuel System … 81 Fuel System Components … 82 Fuel System Indicators … 88 M ultiengine Fuel Systems … 93 Fuel Jettison Systems ____ -------------------- ----------------- 94 Troubleshooting the Fuel System … 94 CHAPTER 5. FLUID LINES AND FITTINGS General … 99 Plumbing Lines … - ___ -- … 99
Identification of :vfaterials ---------------------------------------- 99 Flexible Hose … 100 Plumbing Connectors … 103 Tube Forming Processes … 108 Repair of \fetal Tube Lines … 113 Fabrication and Replacement of Flexible Hose … 114 Installation of Rigid Tubing … 115 Plumbing Assembly Precautions … 117 Support Clamps----------------------------------------------- 118 CHAPTER 6. AIRCRAFT HARDWARE, MATERIALS, AND PROCESSES Aircraft Hardware Threaded _Fasteners … Aircraft Bolts …
121 121 122 Specia I -Purpose Bolts … - - - -- - - -- -- - _ - _ -- - - - - -- -- - 123 Aircraft Nuts … - ----- _ ---- ------- ----- -- 126 Aircraft w-as hers … "· … - __ - - ___ _ Installation of Nuts and Bolts … - ___ _
Torque and Torque 'Wrenches ------------------------------------ Aireraft Screws_
Repair of Damaged Internal Threads ------------------------------
RPpair of Damaged Holes with Acres Fastners Sleeves ---------------- Turnlock Fasteners_ Control Cables_ Push- Pull Tuhe Linkage … Pins __ _ Safety :Methods_ Rivets … Plastics … Rubber __ Shock Ah1-iorber ConL … Seals __ . …
Ga:-.kets __ Wipers_
vi
130 132 132 135 137 138 141 143 144 144 145 150 163 164 166 166 168 169
3/31/99 AC 65-9A CHG 1
Sealing Compounds … . 16 9 Corrosion Control … 171 F orrns of Corrosion … 172 Factors Affecting Corrosion … 173 Preventive Maintenance … 173 Inspection … 17 4 Corrosion-Prone Areas … 174 Corrosion Removal … 176 Corrosion of Ferrous Metals … 177 Corrosion of Aluminum and Aluminum Alloys … 177 Corrosion of Magnesium Alloys … 179 Treatment of Titanium and Titanium Alloys … 180 Protection of Dissimilar Metal Contacts … 180 Corrosion Limits … 180 '.·:. Processes and Materials Used in Corrosion Control … 181 Chemical Treatments … 183 Protective Paint Finishes … : … 185 Aircraft Cleaning … 185 Interior Cleaning … 186 Powerplant Cleaning … … 188 Solvent Cleaners … … 188 Emulsion Cleaners … … 189 Soaps and Detergent Cleaners … … 189 Mechanical Cleaning Materials … … 190 Chemical Cleaners … … 190 Structural Metals … … 191 Metalworking Processes … , … 193 Ferrous Aircraft Metals … … 194 Nonferrous Aircraft Metals … 198 Substitution of Aircraft Metals … … 204 Principles of Heat Treatment … … 205 Heat-Treating Equipment … … 205 Heat Treatment of Ferrous Metals … … 208 Casehardening … … 211 Heat Treatment of Nonferrous Metals … … 212 Solution Heat Treatment … 213 Precipitation Heat Treating … … 214 Annealing of Aluminum Alloys … 216 Heat Treatment of Aluminum Alloy Rivets … 216 Heat Treatment of Magnesium A!loys … 216 Heat Treatment of Titanium … … 217 Hardness Testing … … 218 CHAPTER 7. PHYSICS General … … 221 Matter … … 221 Fluids … 222 Temperature … 225 Pressure … … 226 Kinetic Theory of Gases … … 227 Atmosphere … … 236 Bernoulli's Principle … 242 Machines … … 243
3/31/99 AC 65-9A CHG 1
vii
AC 65-9A CHG 1 3/31/99
Work, Power, and Energy … … 249 Motion of Bodies … 253 Heat … 256
Sound … 261 CHAPTER 8. BASIC ELECTRICITY General … … 267 Matter … 267 Static Electricity … … 268 Electromotive Force … 271 Current Flow … 272 Resistance … 272 Basic Circuit Components and Symbols … 2 7 4 Ohm's Law.. … 282 Series D.C. Circuits … 286 Parallel D.C. Circuits … 290 Series-Parallel D.C. Circuits … 292 Voltage Dividers … 2 94 Rheostats and Potentiometers … 296 Magnetism … 298
AC 65-9A CHG 1 3/31/99
Storage Batteries.. 306 Lead-Acid Batteries . .. 307 Nickel-Cadmium Batteries … 313 Circuit Protective and Control Devices … 315 Switches … … 317 D.C. Measuring Instruments … … 320 Multimeters … … 325 Voltmeters … … 327 Olunmeters … … 329 Basic Circuit Analysis and Troubleshooting … … 332 Alternating Current and Voltage … 338 lndnctance … 344 Capacitance … 346 Ohm's Law for A.C. Circuits... … 352 Transformers … 358 Magnetic Amplifiers … … 364 Vacnnm Tubes … … 366 Transistors.. 369 Rectifiers … Filtering … A. C. Measuring Instruments … Frequency Meters … CHAPTER 9. AIRCRAFT GENERATORS AND MOTORS D.C. Generators … Types of D. C. Generators .. Regulation of Generator Voltage … Differential Relay Switch … Parallelling Generators … D. C. Generator Maintenance … Voltage Regulator Operation … Alternators … Brushless Alternator … Combined A.C. and D.C. Electrical Systems …
viii
… 3TI … 378
… 380 … 3~
387 . . ··········· … 394 … 398
… 402
… 403
... 404 … 407
… 411
. 414 . 415
Voltage Regulation of Alternators … ---- … 417 Alternator Constant.Speed Drive … 423 Synchronizing Alternators … 430 Alternator Maintenance … 433 Inverters … 435 D.C. Motors … ---- -- ___ _ 438 Types of D.C. Motors … ··------- … 445 A.C. Motors … 451 Types of A.C. Motors … -.- … 452 Maintenance of A.C. Motors … 459 CHAPTER 10. INSPECTION FUNDAMENTALS Genera] … 461 Required Inspections … - ___ _ 461 Inspec6on Techniques … 461 Checklist ____ ---------- … -------------------------------- __ _ 462 Aircraft Logs … 463 Special Inspections … -··- __ _ 463 Publications … - ___ - - - - - - - - - - - - 464 Magnetic Partide Inspection … 469 Magnetizing Equipment … … 474 Demagnetization … 477 Dye-Penetrant Inspection … 477 RadiographY--------------------------------------------------- 479 Ultrasonic Testing … 481 Eddy Current Testing … --------- … :... --------- … ---- _ 485 Visual Inspection … 486 ; '."' CHAPTER 11. GROUND HANDLING, SAFETY, AND SUPPORT EQUIPMENT
Introduction … 489 General … =- … 489 Starting Engines _ --------------- … ---------- … ---------- 489 Turboprop Engines … 491 Turbojet Engines … 492 Electrical Power … 495 Hydraulic Power … 495 Air Conditioning and Heating Units … 496 Ground Support Air Start Units … 496 Preoiling Equipment_ __ 497 Aircraft Fueling … 497 Fire---------------------------------------------------------- 500 Recommended i\farkings to Indicate Extinguisher Suitability ---------- 503 Aircraft Fire Extinguishers … ------- ___ ----- _ -------------- __ 503 Servicing Aircraft with OiL … 505 l\tlain tenance Safety … 507 Servicing Aircraft Oxygen Systems … 508 Aircraft Tiedown … 508 Securing Light Aircraft … 511 Securing Heavy Aircraft … 512 Aircraft Tied own for Storm Conditions … 512 Movement of Aircraft … ~ … 517
IX
Jacking Aircraft- … --· ___ ----_ - __ - 523 Cold Weather Suggestions … 525 CHAPTER 12. HANDTOOLS AND MEASURING DEVICES Introduction … ------------------------------------------ 529 General-Purpose Tools … --- 529 Metal Cutting Tools … -- __ -- -- - 534 Layout and Measuring Tools … 542 Taps and Dies … 547
- _;,
X
INTRODUCTION
The use of mathematics is so woven into every area of everyday life that seldom if ever does one fully realize how very helpless we would be in the performance of most of our daily work without the knowledge of even the simplest form of mathematics. Many persons have difficulty with relatively simple computations involving only elementary mathematics. Performing mathematical computations with success requires an understanding of the correct procedures and continued practice in the use of mathematical manipulations.
A person entering the aviation field will be required to perform with accuracy. The aviation mechanic is often involved in tasks that require mathematical computations of some sort. Tolerances in aircraft and engine components are often critical, making it necessary to measure within a thousandth or ten-thousandth of an inch. Because of the close tolerances to which he must adhere, it is important that the aviation mechanic be able to make accurate measurements and mathematical calculations.
Mathematics may he thought of as a kit of tools, each mathematical operation being compared to the use of one of the tools in the solving of a problem. The basic operations of addition, subtraction, multiplication1 and division are the tools available to aid us in solving a particular problem.
WHOLE NUMBERS
WHOLE NUMBERS
Addition of Whole Numbers
The process of finding the combined amount of two or more numbers is called addition. The answer is called the sum.
When adding several whole numbers, such as 4567, 832, 93122, and 65, place them under each other with their digits in columns so that the last, or right hand, digits are in the same column.
c--·-
CHAPTER 1
CHAPTER 1
MA TH EMA TICS
When adding decimals such as 45.67, 8.32, 9.8122, and .65, place them under each other so that the decimal points are in a straight ffup-anddown '' line.
To check addition, either add the figures again in the same order, or add them in reverse order.
Subtraction of Whole Numbers
MA TH EMA TICS
Subtraction is the process of finding the difference between two numbers by taking the smaller from the larger of the two numbers. The number
which is subtracted is caHed the subtrahend, the other number the minuend~ and their difference is called the remainder. To find the remainder, write the subtrahend under the minuend, as in addition.
Beginning at the right, subtract each figure in the subtrahend from the figure above it and write the individual remainder below in the same column. When the process is completed, the number below the subtrahend is the remainder.
To check subtraction, add the remainder and the subtrahend together. The sum of the two should equal the minuend.
Multiplication of Whole Numbers
The process of finding the quantity obtained by repeating a given number a specified number of times is called multiplication. More simply stated, the process of multiplication is, in effect, a case of repeated addition in which all the numbers being added are identical. Thus, the sum of 6 + 6 + 6 + 6 = 24 can be expressed by multiplication as 6 X 4 = 24. The numbers 6 and 4 are known as the factors of the multiplication, and 24 as the product.
In multiplication, the product is formed by multiplying the factors. When one of the factors is a single-digit integer ( whole number), the product is formed by multiplying the single-di~it integer with each digit of the other factor from right to left, carrying when necessary.
- _;,
When both facton are multiple,digit integers, the product is formed by multiplying each digit in the multiplying factor with the other factor. Exercise. care, when writing down the partial products formed, to make certain that the extreme right digit lines up under the multiplying digit. It is then a matter of simple addition to find the final product.
EXAMPLE
Determine the cost of 18 spark plugs that cost $3.25 each.
3.25 Xl8
2600 325 58.50
When multiplying a series of numbers together~ the final product will he the same regardless of the order in which the numbers are arranged.
EXAMPLE
MULTIPLY: (7) (3) (5) (2) = 210
7 21 105 X3 XS X2 or 21 105 210
MULTIPLY: (7) (3) (5) (2) = 210
Division of Whole Numbers
7 3 35 XS X2 X6 35 6 210
The process of finding how many times one number is contained in a second number is called division. The first number is called the divisor, the second the dividend, and the result is the quotient.
Of the four basic operations with integers, division is the only one that involves trial and error in its solution. It is necessary to guess at the proper quotient digits, and though experience will tend to lessen the number of trials, everyone will guess incorrectly at some time or another.
Placing the decimal point correctly in the quotient quite often presents a problem. When dividing a decimal by a decimal, an important step is to first remove the decimal from the divisor. This is accomplished by shifting the decimal point to the right the number of places needed to eliminate it. Next, move the decimal point to the right as many places in the dividend as was necessary to move it in the divisor, and then proceed as in ordinary division.
FRACTIONS
A fraction is an indicated division that expresses one or more of the equal parts into which a unit is divided. For example, the fraction f indicates that the whole has been divided into 3 equal parts and that 2 of these parts are being used or considered. The number above the line is the numerator; and the number below the line is the denominator.
If the numerator of a fraction is equal to or larger than the denominator, the fraction is known as an improper fraction. In the fraction \~, if the indicated division is performed, the improper fraction is changed to a mixed number, which is a whole number and a fraction:
15
8
7 1-8
A complex fraction is one that contains one or more fractions or mixed numbers in either the numerator or denominator. The following fractions are examples:
1 5 3
2 8 4 3j 2 ; 2; 5; 2 - 3 8 3
A decimal fraction is obtained by dividing the numerator of a fraction by the denominator and showing the quotient as a decimal. The fraction i equals 5 + 8 = .625.
A fraction does not change its value if both numerator and denominator are multiplied or divided by the same number.
1 3 3 1 -x-=-=- 4 3 12 4
The same fundamental operations performed with whole numbers can also be performed with fractions. These are addition, subtraction, multiplication, and division.
Addition and Subtraction of Common Fractions
In order to add or subtract fractions, all the denominators must be alike. In working with fractions, as in whole numbers, the rule of likeness applies. That is, only like fractions may he added or subtracted.
When adding or subtracting fractions that have like denominators, it is only necessary to add or
subtract the numerators and express the result as the numerator of a fraction whose denominator is the common denominator. When the denominators are unlike, it is necessary to first reduce the fractions to a common denominator before proceeding with the addition or subtraction process.
EXAMPLES
1. A certain switch installation requires i-inch plunger travel before switch actuation occurs. If }-inch travel is required after actuation, what will be the total plunger travel?
FIRST: Add the numerators.
5+1=6
NEXT: Express the result as the numerator
of a fraction whose denominator 1s the common denominator.
5 1 6 -+-=- 8 8 8
2. The total travel of a jackscrew is -H- of an inch. If the travel in one direction from the neutral position is °f6 of an inch, what is the travel in the opposite direction?
FIRST: Subtract the numerators.
13 - 7 = 6
NEXT: Express the result as the numerator
of a fraction whose denominator is the common denominator.
13 16
7 16
6 16
3. Find· the outside diameter of a section of tubing that has a }-inch inside diameter and a combined wall thickness of i inch.
FIRST: Reduce the fractions to a common
denominator.
NEXT:
1 2 - = -· 4 8'
Add the numerators, and express the result as the numerator of a fraction whose denominator is the common denominator.
2 5 7 -+-=- 8 8 8
4. The tolerance for rigging the aileron droop of an airplane is ; inch plus or minus -} inch.
What is the minimum droop to which the aileron can be rigged?
FIRST: Reduce the fractions to a common denominator.
NEXT:
1 8 -=- 5 40
Subtract the numerators, and express the result as in the above examples.
35 40
8 27 --=- 40 40
Finding the least Common Denominator
When the denominators of fractions to he added or subtracted are such that a common denominator cannot be determined readily, the LCD
(least common denominator) can he found by the continued division method.
To find the LCD of a group of fractions, write the denominators in a horizontal row. Next, divide the denominators in this row by the smallest integer t.hat will exactly divide two or more of the denominators. Bring down to a new row all the quotients and numbers that were not divisible. Continue this process until there are no two numbers in the resulting row that are divisible by any integer other than one. Multiply together all the divisors and the remaining terms in the last row to obtain the least common denominator.
EXAMPLE
What is the LCD for -t lfi", -l-~, -}!?
FIRST: Write the denominators in a horizontal row and divide this row by the smallest integer that will exactly divide two or more of the numbers.
2 [8 20 36 45 4 10 18 45
NEXT: Continue this process until there are
no two numbers in the resulting row that are divisible by any integer other than one.
2 2
3
3
5
8 4 2 2 2
2
20 10 5 5 5 1
36 45 18 45
9 45 3 15 1 5 1 1
THEN: Multiply together all the divisors and remaining terms in the last row to obtain the LCD.
LCD = 2 X 2 X 3 X 3 X 5 X 2 = 360
Multiplication of Fractions
The product of two or more fractions is obtained by multiplying the numerators to form the numerator of the product and by multiplying the denomi.
nators to forrn the ·denominator of the product. The resulting fraction is then reduced to its lowest terms. A common denominator need not be found for this operation, as the new denominator in most cases will be different from that of all the original fractions.
EXAMPLE
What is the product of J X ti X f?
FIRST: Multiply the numerators together.
3 X 12 X 1 = 36
3 X 12 X 1 = 36
NEXT: Multiply the denominators together.
5 X 22 X 2 = 220
THEN: Reduce the resulting fraction to its lowest terms.
36 9 220 55
Cancellation
Cancellation is a technique of dividing out or cancelling all commo11 factors that exist between numerators and denominators. This aids in locating the ultimate product by eliminatirtg much of the burdensome multiplicati~n.
5 X 22 X 2 = 220
EXAMPLE
What is the product of-}% X {? The product could be found by multiplying 18 X 5 and 10 X 3, then dividing the product of the numerators by the product of the denominators. However, a much easier method of solution is hy cancellation. It is apparent that the 10 in the denominator and the 5 in the numerator can both be divided an exact number of times by 5.
Also, the 18 and l are bollh e,eaetly divisible by 3.
2 1
The resulting 6 in the numerator and the 2 in the denominator are both divisible by 2.
3 6 1 1'8 $ 3 X 1 3 i0 X Z = 1 X 1 = 1 = 3
i 1 1
The fraction is thus reduced to its lowest terms, and the final multiplication and division steps are performed with ease when compared with the task of multiplying and dividing the larger fractions.
Division of Common Fractions
The division of common fractions is accomplished most conveniently by converting the problem into a multiplication of two common fractions. To divide one fraction by another fraction, invert the divisor fraction and multiply the numerators together and the denominators together. This is known as the inverted divisor method.
Always keep in mind the order in which the fractions are written. It is important in division that the operations be performed in the order indicated. Also, remember that it is always the divisor that is inverted, never the dividend.
MIXED NUMBERS
MIXED NUMBERS
Mixed numbers can be added, subtracted, multiplied, or divided by changing them to improper fractions and proceeding as when performing the operations with other fractions.
EXAMPLE
A piece of tubing 6--{-r; inches long is cut from a piece 24! inches long. Allowing / 6 inch for the cut,· what is the length of the remaining piece?
FIRST: Reduce the fractional parts to like fractions and complete the subtraction process. 13183141 2 16 - 16 - 16 - 16 16 - 16 - 4
NEXT: Subtract the integer parts.
24 - 6 = 18
THEN: Combine the results obtained in each step.
l 18 + - = 4
DECIMALS
1 184 inches.
Decimals are fractions whose denominators are 10 or some multiple of 10, such as 100, 1,000, 10,000, etc. They are indicated by writing one or more digits to the right of a reference mark called a decimal point. Thus:
6 10
6 100
.6, both read six tenths.
.06, both read six hundredths.
6 l,OOO = .006, both read six thousandths.
When wntmg a decimal, any number of zeros may he written at the right end without changing the value of the decimal. This mav he illustrated in the following manner:
5 1 50 1 5 = - = -· 50 = - = -· . 10 2' . 100 2' .500 500 1,000 I
2
A decimal fraction that is written where there is no whole number as .6, .06, etc., is caHed a pure decimal. When a whole number and a decimal fraction are written together as 3.6, 12.2, 131.12, etc., the number is known as a mixed decimal.
2.34 Ohms
2.34 Ohms
37.5 Ohms
.09 Ohms
FIGURE: 1-1. A series circuit.
Addition of Decimals
When computing decimals, the rule of likeness requires that we add or subtract only like denominations. This rule was discussed previously under addition and subtraction of whole numbers. To add or subtract decimal expressions, arrange the decimals so that the decimal points align vertically, and add or subtract as with integers. Place the decimal point in the result directly below the decimal points in the addends or minuend and subtrahend.
37.5 Ohms
EXAMPLES The total resista_11ce of snies circuit ( figure 1-1) is equal to the sum of the individual resistance:,. What is the total resistance for the diagram shown in this example?
.FIRST: Arrange the decimals in a vertical column so that the decimal points are in alinement.
2.34 37.5 . ()()
NEXT: Complete the addition following the technique used in adding whole numbers. Place the decimal point in the result directly below the other decimal points.
2.34 37.5 .09 39.93 ohms
Subtraction of Decimals
A ~Pries circuit <"Ontaining two resistors has a total resistance of 37.27 ohms. One of the resistors has a vaJue of 14.88 ohms. \Vhat is the value of the remaining resistor?
FIRST: Arrange the decimals in a vertical eolumn so that the de{'imal points are in alinement.
NEXT:
37 .27 -14.88
Pt•rform the subtraction process using the procedure for subtracting whole numbers. Place the decimal point in the result directly below the other deeimal points.
37.27 -11.88
22 .39 ohm~
- .: '
Multiplication of Decimals
The multiplication of a decimal by another decimal will always produce an answer smaller than either of the two numbers. When a decimal is multiplied by a whole number or by a mixed decimal, the answer will lie between the two numbers.
When multiplying a decimal fraction by an integer or another decimal, establishing the position of the decimal point in the product causes the greatest amount of difficulty.
To multiply decimals, ignore the decimal points and multiply the terms as though they were whole numbers. To locate the decimal point in the product, begin at the right of the product and point off toward the left the number of decimal places that will equal the sum of the decimal places in the quantities multiplied.
EXAMPLE
Using the formula, Watts = Amperes X Voltage, what is the wattage of an electric heater that uses 9.45 amperes from a 120-volt source?
FIRST: Arrange the terms and multiply. Ig-
nore the decimal point.
9.45 Xl20
9.45 Xl20
000 1890 945 113400
NEXT: Locate the deci_mal point. Begin at the right of the product and point off toward the left the number of places that will equal the sum of the decimal places in the quantities multiplied.
9.45 Xl20 18900 945 1134.00
In some problems the number of digits in the product will be less than the sum of the decimal places in the quantities multiplied. Where this occurs, merely add zeros to the left of the product until the number of digits equals the sum of the decimal places in the quantities multiplied.
EXAMPLE
Multiply .218 by .203.
FIRST: Arrange the terms and multiply, ig-
noring the decimal point.
.218 .203
654 4360 44254
NEXT: Locate the decimal point. Add a zero to the left of the product so that the number of places will equal the sum of the decimal places in the quantities mult plied.
.218 X.203
654 4360 .044254
Division of Decimals
When one or both of the terms of a division problem involve decimal expressions, the quotient is found by converting the problem to one involving a whole number.
Two facts relating to division of decimals that must he borne in mind are: ( 1) When the dividend and divisor are multiplied by the same number, the quotient remains unchanged; and (2) if the divisor is a whole number, the decimal place in the quotient will align vertically with the decimal in the dividend when the problem is expressed in long division form.
To divide decimal expressions, count off to the right of the decimal point in the dividend the same number of places that are located to the right of the decimal point in the divisor. Insert a caret ( /\) to the right of the last digit counted. If the number of decimal places in the dividend is Jess than the number of decimal places in the divisor, add zeros to the dividend, remembering that there must be at least as many decimal places in the dividend as in the divisor. Divide the terms, disregarding the decimal points entirely. Place the decimal point in the quotient so that it alines vertically with the caret mark in the dividend.
EXAMPLE
The wing area of a certain airplane is 245 square feet; its span is 40.33 feet. What is the mean chord of its wings'?
FIRST: Arrange the terms as in long division
and move the decimal point to the right, adding zeros as necessary, and insert a caret.
40.33,.J245.00._
NEXT: Divide the terms, disregarding the decimal points entirely. Add ad~ ditional zeros to the right to permit carrying the quotient to the desired accuracy.
6 07 40 .33,,,1245. 00,.00 241 98 3 020 0 000
3 0200 2 8221
1979 THEN: Place the decimal point in the quotient so that it alines vertically with the caret mark in the dividend.
6. 07 feet 40. 33,.[21500,.60 24198
3020 0000
30200 28221 1979
Rounding Off Decimals
There i:'.\ a ~eneral tende1H') lo think of all numbers as lwing prc('isc. ,\etually the whole realm of rneas11rement involves numl,ers that are only approximations of precise numbers. J<"'or example, measurements of length. area, and volume are al hest approximations. The degree of accuracy of 1licse mcasurem<'llls depends on the refinement of tht.~ measuring instrumenlt-i.
Occasionally it is neecssary to round a numher to some value that it-i practieal to use. For example, a measurement is ("omputed lo be 29.4948 inches. It is impraclical, if not impossible, to measure this accurately with a stet>l rule ,vhich is accurate only to·,/.- of an inch.
To use this measurement, we can use the process of Hrounding. '
1 A decimal expression is Hrounded off" by retaining the lligits for a certain number of places and discarding the rest. The retained number is an approximation of the computed or exact number. The degree of accuracy desired determines the number of digits to Le retained. When the <ligit immediately to the right of the last retaineJ digit is a 5, or greater than 5, increase the last retained <ligit hy I. W'J1en the digit imme,liately to the right of the last retained digit is less than 5, leave the last retained digit unchanged.
EXA~IPLE
Round 29.'±9,1.S to the nearest tenth.
FIRST: Determine the number of digits to retain. In this case one-tenths being the first place to the right of the decimal point.
29A948
NEXT: Change the value of the last retained digit, if required. In this case, since 9
is greater than 5, the final decimal is expressed thus:
29 . 4948 becomes 29. 5 inches.
Converting Decimals to Common Fractions
To change a decimal fraction to a common fraction, count the number of digits to the right of the decimal point. Express the number as the numerator of a fraction whose denominator is l followed by the number of zeros that will equal the number of digits to the right of the decimal point.
EXAMPLE
Express .375 as a common fraction.
FIRST: Count the number of digits to the right of the decimal point.
.375 I I\ 1 2 3
NEXT: Express the number as the numerator of a fraction whose denominator is l followed by the number of zeros that will equal the number of digits to the right of the decimal point.
375 ·375 = 1000
·-':,
r. (
C.
•':.
T
5 -'----'---~-- -- 3-
7 5- 16
8 l
FIGURE 1-2. Locating the hole center.
Many times a dimension appearing in a maintenance manual or on a blueprint is expressed in decimal fractions. In order to use the dimension, it must be converted to some equivalent approximation applicable to the available measuring device. From the mechanic'i', standpoint, the steel rule will he the device mot--t frcqurntly used.
To change a decimal ?o the nearest equiYalent fraction having a desired denominator, multiply the decimal by the dt>sircd denominator. The result will be the numerator of the desired fraction.
EXA\!PLE
When accurate hol1•s of 1miform diameter are required, they are first drilleri -/i inch undcrsize and reamed to the df'"sir,~d rl.iameter. -W'hat size drill would he used before n.·arning a h0lc to .763?
FIRST: !\lultiply tht: d('('irnal ln· the desired denomin:itnr ,,r /i l.
:'liEXT:
TIIEl\:
X<•.1.
:)0.):2 . --.. J.,) I {)
l{ound the prodtwl lo a whok numlwr ;:i,nd ('Xpre~,, it a,.; t!w numt•ralnr of1hc desireil dcnominatnr.
.j<) 48.832 ~- - (>.l
To d<'tnminc tlw drill Rize. suhtrart "l\\ inch from the finish('d hok i:.ize.
JO
6 l l (d
., :' .inch drill.
1
Converting Common Fractions to Decimals
To convert a common fraction, whether proper or improper, to a decimal, divide the numerator by the denominator. Add zeros to the right to permit carrying the quotient to the desired accuracy.
EXAMPLE
Find the distance the center of the hole (figure 1-2) is from the plate edges when the center of the hole is in the center of the plate. Express the length and width of the plate in decimal forms, and then divide each by 2. Express the final result to the nearest 32nd.
FIRST:
NEXT:
THEN:
Change the mjxed numbers to improper fractions.
7 87 5-- = -· 16 16'
.5 29 3- = - 8 8 Convert the improper fractions to decimal expressions.
87 5 3
0 - = .. 4 7o: 16 . ,
29 = 3.625 8
Divide the decimal expressions by 2 to find the center of the plate.
.5.4375 - -~·-- = 2. 7188;
2 3 .625 = 1.813 2
FINALLY: Express the final results to the nearest 32nd.
2.7188
PERCENTAGE
26 1- 32
Then· :ire- many problems that arise every day in\-olving tlw !Wrt't'tlt expression. The greatest 1111mlwr of perc,~ntage problems involve some kind of ('n111parison of a part to the whole. Such com~ pari~<ms h<'eomc percentage problems when the ratio fraf'tion is Pxpresscd as a percent.
A fraction having the specific power of 100 for the denominator is given the name percent. When writing these fractions, the percent symbol (%) is substituted for the denominator. Any common fraction or decimal can he expressed as a percent. The fraction -} can thus he expresse<l as .20 or as :20 1wrcent or simply as 20%, Note .that the per- ('Cnt. is the same as the decimal fraction except 1hat t.hc decimal point has been moved two places to the right and deleted after ••percent" or the symbol '"~,; "' has heen added.
Expressing a Decimal as a Percent
To express a decimal as a percent, move the decimal point two places to the right ( add a zero if necessary) and affix the percent symbol.
EXAMPLE
Express .90 as a percent.
:FIRST: :Move the decimal point two places to the right.
90.
NEXT: Affix the percent symbol to the right
after dropping the decimal point.
90% Expressing a Percent as a Decimal
Sometimes it ma)' he necessary to express a percent as a decimal. Keeping in mind that a percent is simply a decimal with the decimal point moved two places to the right, aH that is necessary to express a percent as a decimal is to move the decimal point two places to the left.
Expressing a Common Fraction as a Percent
The technique involved in expressing a common fraction as a percent is essentially the same as that for a decimal fraction. The one difference is the procedure necessary to convert the fraction to a decimal.
EXAMPLE
Express ~ as a percent.
FIRST: Convert the fraction to a det·imal.
s ·- = 5 + 8 = .625 8
NEXT: Move the de<'imal point two places to the right and affix the percent symbol.
.62.'i = 62.S(Xj
Finding What Percent One Number is of Another
Determining \dlat pncent one number is of another is done l1y writing the part number as the numerator of a fraction and the whole number as the denominator of that fraction, and expressing this fraction as a percentage.
EXAMPLE
A motor rated as 12 horsepower is found to he delivering 10.75 horsepower. What is the motor efficiency expressed in percent'!
FIRST: Write the part number, 10.75, as the numerator of a fraction whose denominator is the whole number, 12.
10.75 12
NEXT: Convert the fraction to its decima] equivalent.
10.75 + 12 = .8958
THEN: Express the decimal as a percent.
.8958 = 89.58% efficient.
Finding a Percent of a Given Number
The technique used in determining a percent of a given number is based on the fundamental process of multiplication. It is necessary to state the desired percent as a decimal or common fraction and multiply the given number by the percent expressed as a decimal or other fraction.
EXAMPLE
The cruising speed of an airplane at an altitude of 7 .500 feet is 290 knots. What is the cruising speed at 9,000 feet if it has increased 6 percent?
FIRST: State the desired percent as a decimal.
6% = .06
NEXT: Multiply the given number by the decimal expression.
290 X .06 = 17.40
THEN: Add the new product to the given
number. This is the new cruising speed.
290 + 17.4 = 307..1 knots.
Finding a Number When a Percent of It is Known
To determine a number when a percent of it is known, express the percent as a decimal and divide the known number by the decimal express10n.
EXAMPLE
Eighty ohms represent 52 percent of a circuit's total resistance. Find the total resistance of this circuit.
,'
FIRST: Express the percent as a decimal.
52% = .52
NEXT: Divide the known number by the
decimal expression.
80 -;- .52 = 153.8 ohms total resistance.
RATIO
An important application of the common fraction is that of ratio. A ratio represents the comparison of one number to another number. Comparison by the use of ratios has widespread application in the field of aviation. A ratio is used to express the comparison of the volume of a cylinder when the piston is at bottom center to the volume of a cylinder when the piston is at top center. This is referred to as the compression ratio. The aspect ratio of an aircraft wing is a comparison of the wing span to the wing chord. The relationship of maximum speed, wing area, wing span, loaded weight, and horsepower of different makes and models of aircraft may be compared through the use of ratios.
A ratio is the quotient of one number divided by another number, expressed in like terms. A ratio, therefore, is the fractional part that one number is of another. A ratio may be expressed as a fraction, or it may be written using the colon (:) as the symbol for expressing ratio; thus the ratio i can be written 7: 8.
Finding the Ratio of Two Quantitites
To find a ratio, the first term is divided by the second term. Both quantities of both terms must be expressed in the same t.1:nits, and reduced to their lowest terms.
EXAMPLES
I. What is the weight ratio of a fuel load of 800 gallons to one of 100080 pounds? Assume that the fuel weighs 7 .2 pounds per gallon.
FIRST: Express the fuel load in gallons as the numerator of a fraction whose denominator is the fuel load in pounds.
800 gal. R= 10,080 lb.
NEXT:
R
Express both quantities unit (pounds).
(800 X 7.2) lb.
10,080 lb.
in the same
THEN: Perform the indicated mathematical manipulations and reduce to lowest terms.
R = (800 X 7.2)
10,080
5760 10,080
4 = 7, or 4:7
What is the ratio in gallons?
FIRST: Express the ratio in fractional form.
R = 800 gal.
10,080 lb.
NEXT: Express both quantities in
unit (gallons).
800 gal. 10.080 R
7.2
the same
THEN: Perform the indicated mathematical
manipulations and reduce to lowest terms.
800 R=-- 10,080
800 4 1,400 = 7' or 4' 7
7.2 2. If the cruising speed of an airplane is 200 knots and its maximum speed is 250 knots, what is the ratio of cruising speed to maximum speed?
FIRST: Express the cruising speed as the
numerator of a fraction whose denominator is the maximum speed.
R
NEXT:
200 250
Reduce the resulting lowest terms.
fraction to its
THEN: Express the result as a ratio of one.
4 R = 5. or .8:1 (Read 8/lOths to one)
Finding the Quantity of the First Term
Now consider the situation when the ratio and the quantity that corresponds to the secon<l term are given, and it is required to find the quantity that corresponds to the first term. To solve this type problem, multiply the term that corresponds to the second term by the fraction that represents the ratio.
EXAMPLE
The given ratio is 5/7 and the quantity that corresponds to the second term is 35. Find the quantity that corresponds to the first term.
FIRST: Express the problem as the product of the second terin times the ratio.
35 X 5/7 =
35 X 5/7 =
NEXT: Perform the indicated operation.
5 :iii X 5/1 = 25
l
The first term is 25. The proof of this can he demonstrated by shm\·ing that the ratio of 25 to 35 is 5: 7, reduced to lowest terms.
25/35 = 5/7
Finding the Quantity of the Second Term
To solve a problem of this type, the ratio of the two quantities and the quantity that corresponds to the first term must he known. The solution is obtained by dividing the known number by the fraction that represents the ratio.
EXAMPLE
The ratio of two quantities is 2/3; the quantity that corresponds to the first term is 100. Find the quantity that corresponds to the second term.
FIRST: Express the problem as the quotient of the first term divided by the ratio.
100 + 2/3 =
NEXT: Perform the indicated operation.
100 + 2/3 = so !00 X 3/2 = 150
1
The second term is 150. Again, this can he proved by expressing 100 as a ratio of 150.
100/150 = 2/3
PROPORTION
A proportion is a statement of equality between two or more ratios. Thus,
3 6 - =-;or 3:4 = 6:8. 4 8
This is read 3 is to 4 as 6 is to 8. The first and last terms of the proportion are cal1ed the extremes. The second and third terms are called the means.
In any proportion, the product of the extremes is equal to the product of the means. In the proportion
2:3 = 4:6
the product of the extremes, 2 X 6, is 12; the product of the means, 3 X 4, also is 12. An in~ spection of any proportion will show this to be true. This rule simplifies the solution of many practical problems.
An airplane flying a distance of 300 miles used 24 gallons of gasoline. How many gallons will it need to travel 750 miles?
300:750 = 24:x
(300)(x) = (750) (24)
300x = 18,000
X = 60
Sixty gallons of gasoline will he required to travel a distance of 750 miles.
POSITIVE AND NEGATIVE NUMBERS
POSITIVE AND NEGATIVE NUMBERS
Positive and negative numbers are numbers that have directional value from a given starting point or from zero. Numbers above or to one side, usually right1 of zero are designated as positive
( +) ; those below or to the opposite side, usually left, of zero are designated as negative ( - ) . Figure 1-~ is representative of signed numbers on a horizontal scale.
-5 -4 -3 -2 -I
I I
0 I +,r +2 +3 +4 +5
0 I +,r +2 +3 +4 +5
I I I I
FIGURE 1-3. A scale of signed numbers.
The sum of positive numbers is positive. The sum of negative numbers is negative.
. '
Addition
To add a positive and a negative number, find the difference in their actual values and give this difference the sign (+or-) of the larger number.
EXAMPLE
The weight of an aircraft is 2,000 pounds. A radio rack weighing 3 pounds and a transceiver weighing 10 pounds are removed from the aircraft. What is the new weight? For weight and balance purposes, alJ weight removed from an aircraft is given a minus sign, and all weight added is given a plus sign.
FIRST: Add the values for the removed weights.
10+3=13
NEXT: Prefix the sign for removed weights.
-13
THEN: Add the sum of the removed weights
to the total weight, following the rule for unlike signs.
+2000-13= + 1987 pounds.
Subtraction
To subtract positive and negative numbers, change the sign of the subtrahend (the number to be subtracted from another) and proceed as in addition.
EXAMPLE
What is the temperature difference between a temperature reading of + 20 at 5,000 feet and a reading of -6 at 25,000 feet? Follow the rule, Ha change in temperature is equal to the first reading, subtracted from the second reading."
FIRST: Change the sign of the number to be subtracted. + 20 becomes - 20.
NEXT: Combine the two terms, following the
rule for a·dding like signs. (-6) + (-20) = -26 degrees.
Multiplication
The product of two positive numbers is positive ( + ) . The product of two negative numbers is positive ( +). The product of a positive and a negative number is negative ( - ) .
EXAMPLES
3X6=18 -3X-6=18
Division
-3X6=-18 3X-6=-18
The quotient of two positive numbers is positive. The quotient of two negative numbers is positive. The quotient of a positive and negative number is
negative.
EXAMPLES
6+3=2 -6+-3=2
POWERS AND ROOTS
POWERS AND ROOTS
Power
-6+3=-2 6+-3=-2
When one number, the base, is used as a factor two or more times, the result is a power of the base. A positive integral exponent, written as a
small number just to the right and slightly above the base number, indicates the number of times the base is used as a factor. Thus, 4 squared, or
42 means 4 X 4, which is 16. The 4 is the base, the 2 is the exponent, and the 16 is the power.
Roots
A root of a number is one of two or more equal numbers that, when multiplied together, will pro~
duce the number. Such a number is called an equal factor. Thus, two equal factors that will produce 9 when multiplied together are 3 and 3. Therefore, the square root of 9 equals 3. This may be written y'9 = 3. The symbol v'- is called a radical sign. Another method of indicating the square root of a number is to use a fractional exponent such as 9112 = 3. If the root to be taken is other than a square root, it may be shown in a similar manner; that is, the cube root of 9 may be written 9113• For example, the cube root of 8 equals 2 and may be written VB = 2, or 8113 = 2; the fourth root of 256 equals 4 and may be written '1256 = 4, or 256114 = 4.
Computation of Square Root
It is comparatively easy to determine the square root. of such numbers as 4, 9, 16, and 144. The numbers are the perfect squares of small numbers. Unfortunately, all numbers are not perfect squares; neither are they small. The square of a number is the product of that number multiplied by itself. Extracting the square root of a number is the reverse process of squaring a number, and is essentially a special division process. A description of this process follows and is presented in example form.
EXAMPLE
Find the square root of 213.16
FIRST: Starting at the decimal point, and
marking off in both directions from the decimal point, separate the number into periods of two figures each. The last period at the left end need not have two figures; all others must have two figures. A zero may he added to the right end so that the period will have two figures.
NEXT: Select the largest number that can be squared in the first period. Place the selected number above the radical sign, and place the square of this
number under the first period and subtract.
1 v213.16 l l l
THEN: Bring down the next pair.
(I) Multiply the root by 2 and place
the product to the left of the remainder as the trial divisor.
(2) Determine the number of times
the tl'ial divisor will go into that portion of the remainder that is one digit more than the trial divisor. Write this number to the right of tbe digit in the trial divisor to form the final divisor and also to the right of the digit in the root.
(3) Multiply tbis number times the
completed divisor. If the resulting product is larger than the remainder, reduce the number by one, both in the root and in the final divisor, and repeat the multiplication process.
( 4) Subtract the product formed
from the remainder and bring
down the next pair to form a new remainder.
(5) To complete the solution of ex-
tracting the square root, simply repeat the procedure set forth in this step for each period of numbers remaining. It is unnecessary to carry the root beyond the number of digits possessed by the original number.
l 4. 6 V213.16
l 24 ll3 96 286 17 16 17 16
·'
Two will divide into 11, 5 times. However, 5 X 25 is greater than 113, so the 5 must he reduced to a 4.
The decimal is placed in the root so that the number of digits in l he whole number portion of the root is equal to the sum of the periods, or pairs, in the whole number portion of lhe number from which the root was exlracted.
Powers of Ten
The difficulty of performing mathematical problems with very large (or very small) numbers and the counting and writing of many decimal places are both an annoyance arnl a source of error. The problems of representation and calculation are simplified by Lhc use of ''powers of ten." (Sec figure 1-4 .. ). This system, sometimes referred to as ''Engineer's Shorthand," requires an understanding of the prinriplcs of the exponent. These are summarized as follows:
(1) The positive exponent (or power) of a
number is a shorthand method of indicating how many times the number is multiplied by itself. For example, 23
(read as 2-cuhed or 2 to the third power) means 2 i:::, to he multiplied by itself 3 times: 2 X 2 X 2 = 8. A number with a negative exponent may he defined as its inverse or reciprocal (1 divided hy Lhc number) with the same exponent' made positive. For example, 2-,, (read as 2 ·to the minus 3 power) is the same as
l (2) 3
l 2X2X2
l
8
(2) Any number, except zero, to the zero
pow,~r is equal to 1. When a number is written without an exponent, the ya]uc of the exponent is 1. '\\1hcn an exponent has no sign ( + or - ) preceding it, the exponent is positive.
(3) The value of a numher does not change
when it is both multiplied and divided hy the same factor (5 X 10 + 10 - 5).
M.oving the decimal point of a number to the left is the same as dividing the number Ly 10 for each place the decimal point moves. Conversely, moving the decimal point to the right is the same as multiplying the number by 10 for each pla<.'e the decimal point moves.
POWER OF
POWER OF
TEN EXPAJ\'SION VALUE
Positive Exponent ,. 10 X lOX lOx lOx 10 xlO 1,000,000 ,. lOXlOXlOXlOXIO 100,000 ,. 10 X IO X IO X JO 10,000 ,. 10Xl0XI0 ,,ooo '"
IO X 10 mo w rn w '" Th~ velocity of li_~ht, 30, 000, 000, 000 centimeters per second, simpllfie; to 3 X IO" centimeter, per scc'Ond.
TEN EXPAJ\'SION VALUE
)\'egati"e Exponent
10·• = __!:_ ' -'- rn "
10 = 0.1
10-•"" ..2... ' ,. IO X 10 100 = O.ot
10·• = .J... ' ,. !OX !Ox 10 1,000 = 0,001 w- = .J... ' ,. 1nx10x1oxw 10.000 = 0.0001
JO"'= -2. ' '"
lO X !() X lO X 10 X IO 1no.ooo = 0.00001
10-• = -2. ' ,e !OX !Ox !OX IOx !OX 10 1,000,000 = 0.000001
The mMS of an electron, 0.000, 000, 000, 000, 000, 000, 000, 000, 000, Sil gram. bccom~; 9.11 X 10-" pam.
FIGURE 1-4. Powers of ten and their equivalents.
The procedure for use of powers of ten may he summarized as follows:
(1) Move the decimal point to the place
desired. Count the number of places the decimal point is moved.
(2) Multiply the altered number hy 10 to
a power equal to the number of places the decimal point w~s moved.
(3) The exponent of 10 is negative if the
decimal point is moved to the right, and it is positive if the decimal point is moved to the left. An aid for remembering the sign to he used is: L,
A, R, D. When the decimal point moves Left, you Add; and when the decimal point moves Right, you Deduct.
In most instances, you will find it convenient to reduce the numbers used to numbers between 1 and 10 times 10 to the proper power. Unless otherwise specified, all answers to problems using powers of ten will conform to that requirement.
Powers of Ten Added and Subtracted
Before using powers of ten in mathematical operations, it will be bene:6cial to review a few more principles governing exponents:
If two or more numbers are written with the same base, their _product is equal to the base raised to a power equal to the algebraic sum of their exponents.
3' X 3s X 3' = 3' + , + , = 312
If two numbers are written whh the same base, their quotient is equal to the base raised to a power equal to the algebraic difference of their exponents (numerator's exponent minus denominator!s exponent).
4' -- = 45-3 = 42 4'
A factor may be moved from numerator to denominator or from denominator to numerator by changing the sign of its exponent. Thus we have
32 43 1 = 32 X 43 = - = ---- 4-3 3-2 4-a X 3-2
The bases must be the same before numbers can be multiplied or divided by the addition or subtraction of their exponents. Thus1 a5 X b6 cannot be combined because the bases ( a and b) are not the same.
Note particularly that the rules specify algebraic addition and algebraic subtraction of the powers. Here are some summarizing examples;
37 X 3-n = 1 37+{-11) = 31-11 = 3-4 = - . 3'
5s = 5s-(-6l = 5sH = 5I4. 5-6
68 1 - = 68-12 = 6-4 = - . 612· 64
Multiplication and division employing powers of ten may be performed in three simple steps as follows:
(1) Reduce all numbers to values between 1
and 10 multiplied by 10 to the proper power. (2) Perform t4e indicated operations. (3) Change the result to a number between
1 to 10 multiplied by IO multiplied hy 10 to the proper power.
COMPUTING AREA
COMPUTING AREA
Mensuration formulas deal with the dimensions, areas, and volumes of geometric .figures. There are five geometric figures with which you should be familiar, and there is a separate formula for finding the area of each. The area of a plane figure is equal to the number of square units it contains. Areas are measured in different units as compared to measuring length. An area that is square and 1 inch on each side is called a square inch. All area units are square units, such as square inch, square foot, square yard, square rod, and square mile. Other area units are the square centimeter, the square meter, et cetera, found in the metric system of measurement.
TABLES OF AREAS
TABLES OF AREAS
144 square inches (sq. in.)
9 square feet
30± square yards
160 square rods 640 acres
= 1 square foot
(sq. ft.). 1 square yard (sq. yd.). = 1 square rod
(sq. rd.). 1 acre (A). 1 square mile (sq. mile).
The technique for determining the area of any geometric shape is based upon the use of formulas. To solve a problem by formula, it is necessary to-
(1) select the formula that covers the
problem situation, (2) insert the known values in the selected
formula, and
·-' .
. '
AREA LW L
AREA LW L
w
FIGURE 1-5. A rectangle.
(3) then make the necessary mathematical
manipulations to find the unknown quantity.
The Rectangle
A rectangle is a four-sided plane figure whose opposite sides are equal and all of whose angles are right angles (90°). The rectangle is a very familiar area in mechanics. It is the cross-sectional area of many beams, rods, fittings, etc. (See figure 1-5.)
The ai:-ea of a rectangle is the product of the measures of the length and width when they are expressed in the same units of linear measure. The area may he expressed by the formula:
A =LW
where: A = area.
L = length of rectangle.
W = width of rectangle.
EXAMPLE
A certain aircraft panel is in the form of a rectangle having a length of 24 inches and a width of 12 inches. What is the area of the panel expressed in square inches?
FIRST: Determine the known values and sub-
stitute them in the formula.
A =LW
A= 24 X 12
NEXT: Perform the indicated multiplication; the answer will be the total area in square inches.
A = 24 X 12 = 288 sq. in.
s
s s AREA= S'
s
FIG URE 1-6. A square.
The Square
A square is a plane figure having four equal sides and four right angles (figure 1-6).
To determine the area of a square, find the product of the length of any two sides. Since a square is a figure whose sides are equal, the formula can he expressed as the square of the sides or:
A= 52
where A is the area and S is the length of a side.
EXAMPLE
What is the area of a square plate whose side measures 25 inches?
FIRST: Determine the known value and substitute it in the formula A= 52
A = 252•
NEXT: Perform the indicated thultiplication; the answer will be the total area in square inches.
A = 25 X 25 = 625 sq. in.
Triangles
A triangle is a three-sided polygon. There are three basic types of triangle: scalene, equilateral or equiangular, and isosceles. A scalene triangle is one in which all sides and angles are unequal, whereas the equilateral triangle, being just the opposite, has equal sides and equal angles. A triangle that has two equal sides and angles is known as an isosceles triangle.
Triangles may be further classified as to right, obtuse, or acute. These terms are descriptive of the included angles of the triangle. A right triangle is one that has one angle measuring 90°. In an obtuse triangle, one angle is greater than 90°,
SCALENE
Unequal Sides and
Angles T
h l
I• b .. I
RIGHT
·:T
I h ___ Jl
'""
I I I h
I
b .. ,
OBTUSE
,..----b1-------1~
ACUTE
EQUILATERAL OR ISOSCELES EQUIANGULAR
EQUILATERAL OR ISOSCELES EQUIANGULAR
Equal Sides and Angles Two Equal Sides and Angles
I T h
I I h I l b .. 1 ~b '"I
ACUTE RIGHT
T:
h I
I li ___ ---
Right 6 - one L = 90°
Obtuse 6 - one L > 90°
Acute D. - all ,._ < 90°
OBTUSE
b
ACUTE
FIGURE 1-7. Types of triangles.
while in an acute triangle all the angles are less than 90°. The various types of triangles are shown in figure 1-7.
ACUTE RIGHT
The altitude of a triangle is the perpendicular
line drawn from the vertex to the base. In some triangles, as in figure 1-8, it may be necessary to extend the base so that the altitude will meet it.
The base of a triangle is the side upon which
; .
2'6" ALTITUDE I
I I I _I_ - - - -"-------....::::,~
2'6" ALTITUDE I
f+-- 3'2" BASE -I
FIGURE 1-8. Triangle.
the triangle is supposed to stand. Any side may he taken as the base.
The area of any triangle may be calculated by using the formula:
I A= -ab 2
where A is equal to Area; ! is a given constant; a is the altitude of the triangle; and b is the base.
EXAMPLE
Find the area of the triangle shown in figure 1-8.
FIRST: Substitute the known values in the
area formula.
NEXT:
I A= -ab= A 2 1 X 2 16" X 3 12 11 2
Solve the formula for the unknown
value.
I A = - X 30 X 38
2
A = 570 sq. in.
1140 2
Circumference and Area of a Circle
To find the circumference (distance around) or the area of a circle it is necessary to use a number called pi (11"). This number represents the ratio of the circumference to the diameter of any circle. Pi cannot be found exactly because it is a neverending decimal, but expressed to four decimal places it is 3.1416, which is accurate enough for most computations. (See figure 1-9.)
Circumference
The circumference of a circle may be found by using the formula:
C = 1rd
where C is the circumference; 1r is the given constant, 3.1416; and dis the diameter of the circle.
Diameter d
\ 1\ <:;- \
~ \ " \ ' ' '
FIGURE 1-9. A circle.
EXAMPLE
The diameter of a certain piston is 5 inches. What is the circumference of the piston?
FIRST: Substitute the known values in the
formula, C = 1rd.
C = 3.1416 X 5
NEXT: Solve the formula for the unknown
value.
C = 15. 7080 inches.
Area
The area of a circle, as in a rectangle or triangle, must be expressed in square units. The distance that is one-half the diameter of a circle is known as the radius. The area of any circle is found by squaring the radius and multiplying by 1r. The formula is expressed thus:
A = 1rr2
where A is the area of a circle; 1r is the given constant; and r is the radius of the circle.
EXAMPLE
The bore (inside diameter) of a certain aircraft engine cylinder is 5 inches. Find the cross sectional area of this bore.
FIRST: Substitute the known values in the
formula, A = 1rr2•
A = 3.1416 X 2.52
NEXT: Solve the formula for the unknown
value.
A = 3.1416 X 6.25
A = 19.635 sq. in.
b,
FIGURE 1-10. A trapezoid.
The Trapezoid
A trapezoid (figure 1-10) is a quadrilateral having one pair of parallel sides. The area of a trapezoid is determined by using the formula:
1 A = 2(b, + b,)h
where A is the area; ·} is the given constant; b1 and b2 are the lengths of the two paraHe] sides; and h is the height.
1 A = 2(b, + b,)h
EXAMPLE
What is the area of a trapezoid whose hases are 14 inches and IO inches, and whose altitude is 6 inches? (Sec fig. 1-11.)
FIRST: Substitute the known values in the
formula.
1 A = 2(b, + b2)h
1 A = 2(10 + 11)6.
NEXT: Solve the formula for t hP, unknown value.
Wing Area
A=
1 A = - X lH 2
1 A = - X lH 2
A = 72 sq. in.
To dC'scribc lhc planform of a '"'·ing (figure ]-12), several terms arc requlred. To calculate wing area, it will be necessary to consider the meaning of the terms-span and chord. The wing span is the length of the wing from wing tip to wing tip. The chord is the width of the wing from leading
FIGURE 1-11. Computing the area of a trapezoid.
edge to trailing edge. If the wing is a tapered wing, the average width or chord, known as the mean chord, must be known in finding the area. The formula for caJculating wing area is:
A= SC
where A is the area expressed in square feet, S is the wing span, and C is the average chord.
The process used in caJculating wing area will depend upon the shape of the wing. In some instances it will be necessary to use the formula for finding wing area in conjunction with one of the formulas for the area of a quadrilateral or a circle.
EXAMPLES
1. Find the area of the wing illustrated in figure 1-13. To determine the area, it is necessary to decide what formula to use. It can be seen that the wing tips would form a 7-foot-diameter circle; the remainder of the wing planform is then in the shape of a rectangle. By combining the formulas for wing area and area of a circle, the area of a wing having circular tips can be calculated.
FIRST: Substitute the known value in the
formula.
A
A
SC+ 1rR2
(25 - 7) (7) + (3.1416) (3.52).
The value for Sis represented by the original wing span less the diameter of the circular tips.
NEXT: Solve the formula for the unknown value.
A (18 X 7) + (3.1416 X 12.25)
A 126 + 38.5
A = 164.5 sq. ft.
.; "
r. s
' C
A= Wing Area, ft.s
C = Average chord, ft.
S = Span, ft.
FIGURE 1~ 12. Wing planform.
2. Find the area of a tapered wing (figure 1-14) whose structural span is 50 feet and whose mean chord is 6'8".
FIRST: Substitute the known values in the
formula.
A SC
A 50' X 6'8".
NEXT: Solve the formula for the unknown value.
A = 50' X 6.67'
A = 333.5 sq. ft.
3. Find the area of a trapezoidal wing (shown in figure 1-15) whose leading edge span measures 30 feet, whose trailing edge span measures 34 feet, and whose chord is 5 feet.
FIRST: Substitute the known values in the
formula.
1 A = 2(b1 + b2)h
A = ~(30 + 34)5.
NEXT: Solve the formula for the unknown value.
1 A = 2(b1 + b2)h
1 - A = ·-(64)o
2
1 A = 2(320)
A = 160 sq. ft.
FIGURE 1-13. Wing with circular tips.
COMPUTING THE VOLUME OF SOLIDS
Solids are objects with three dimensionslength, breadth, and thickness. They are of many shapes, the most common of which are prisms, cyHnders, pyramids, cones, and spheres. OccasionaBy, it is necessary to determine the volume of a rectangle, a cube, a cylinder, or a sphere.
COMPUTING THE VOLUME OF SOLIDS
Since all volm 1es are not measured in the same units, it is necessary to know all the common units of volume and how they are related to each other. For example, the mechanic may know the volume of a tank in cubic feet or cubic inches, but when the tank is full of gasoline, he will be interested in how many gallons it contains. The foHowing table shows the relationship between some of the common units of volume.
UNITS OF SPACE MEASURE
UNITS OF SPACE MEASURE
1,728 cu. in. 1 cu. ft.
27 cu. ft. 1 cu. yd.
231 cu. in. 1 gal.
7.5 gals. 1 cu. ft.
2 pts. 1 qt.
4 qts. 1 gal.
Volume of a Rectangular Solid
A rectangular solid is a solid bounded by rectangles. In other words, it is a square-cornered
FIGURE 1-14. Tapered wing with sweepback.
30 feet ;1 feet \ 34 feet
FIGURE 1-15. Trapezoid wing.
volume such as a box (figure 1-16). If the solid has equal dimensions, it is called a cube.
The formula for determining the volume of a rectangular solid may he expressed thus:
V = lwh
where: V = Volume.
l = length.
w = width.
h = height.
EXAMPLE
A rectangular-shaped baggage compartment measures 5 feet 6 inches in length, 3 feet 4 inches in width, and 2 feet 3 inches in height. How many
cubic feet of baggage will it hold?
FIRST: Substitute the known values into the
formula.
V = lwh
V = 5'6" X 3
14" X 2'3".
NEXT: Solve the formula for the unknown value.
T
h
1 1 1 V = 5-X 3- X 2- 2 3 4
11 10 9 V=-X-X- 2 3 4
165 V = 4
= 41.25 cu. ft.
1'----- 1
FIGURE 1-16. A rectangular solid.
, … , -•• !IA'/ • ::,..J
FIGURE 1-17. A cube.
If 1he rectangular solid is in the shape of a cube (figure 1-17), the formula can be expressed as the cube of the sides:
V = 5'
where Vis the volume and S is the side measurement of the cube.
Area and Volume of a Cylinder
A solid having the shape of a can, length of pipe, or other such object is called a cylinder. The ends of a cylinder are identical circles as shown in figure 1-18.
Surface Area
The surface area of a cylinder is found by multiplying the circumference of the base by the altitude. The formula may be expressed as:
A = 1rdh
where A is the area, 1r is the given constant, d is the diameter, and h is the height of the cylinder.
h
FIGURE 1-18. A cylinder.
;'
-·,r.
-----d -- -----d----- T 0 Piston II
0
/ '
/
----- / ' / " I \ I -- \ ,,...-., \ - I I I \ t \
\ , I ' I -- \ \ I \. / "- / "- / --
/
PISTON AT TOP CENTER PISTON AT BOTTOM CENTER
PISTON AT TOP CENTER PISTON AT BOTTOM CENTER
FIGURE 1-19. Cylinder displacement.
EXAMPLE
How many square feet of aluminum sheet would be needed to fabricate a cylinder 12 feet long and 3 feet 6 inches in diameter?
FIRST: Substitute the known values in the
formula.
A = 1rdh
A = 3.1416 X 3'6" X 12'.
NEXT: Solve the formula for the unknown
value.
A 3.1416 X 3.5' X 12'
A = 132.95, or 133 sq. ft. Volume
The volume of a cylinder may he found by nmltiplying the cross-sectional area by the height of the cylinder. The formula may be expressed as:
V = 1rr2h
where V is the volume; 1r is the given constant; r 2 is the square of the radius of the cylinder; and his the height of the cylinder (figure 1-19).
EXAMPLE The cylinder of an aircraft engine has a bore (inside diameter) of 5.5 inches, and the engine has a stroke of 5.5 inches. What is the piston displacement of one cylinder? The stroke represents the height of the cylinder to he measured, .:.;.,ecause the volume displaced by the piston depends on the length of the stroke.
FIRST: Substitute the known values in the formula.
V = 1rr2h
V = (3.1416) (2.752) (5.S).
NEXT: Solve the formula for the unknown value.
V = 17.28 X 7.56
V = 130.64 cu. in.
GRAPHS AND CHARTS
Graphs and charts are pictorial presentations of data, equations, and formulas. Through their use the relationship between two or more quantities may be more clearly understood. Also, a person can see certain conditions or relationships
GRAPHS AND CHARTS
at a glance, while it would require considerable time to obtain the same information from a written description. Graphs may be used in a number of ways, such as representing a single equation or formula, or they may be used to solve two equations for a common value.
Graphs and charts take many forms. A few of the more common forms are called bar graphs, pictographs, broken-line graphs, continuouscurved-line graphs, and circle graphs. An example of each is shown in figure 1-20. The most useful
of these graphs in technical work is the continuouscurved-line graph.
Interpreting or Reading Graphs and Charts
It is more important, from the mechanic's viewpoint, to be able to read a graph properly than it is to draw one. The relationship between the horsepower of a certain engine at sea level and at any altitude up to 10,000 feet can be determined by use of the chart in figure 1-21. To use this type of chart, simply find the point on the horizontal axis that represents the desired altitude; move upward along this line to the point where jt intersects the curved line; then move to the left, reading the percent of sea level horsepower available on the vertical axis.
EXA.WPLE
"\Vhat percent of the sea level horsepower is available at an altitude of 5,000 feet?
FIRST: Locate the point on the horizontal axis that represents 5,000 feet. Move upward to the point where the line intersects the curved line.
',EXT: Move to the left, reading the percent of sea level horsepower available at 5,000 feet. The available horsepower is 80%.
Nomograms
It is often necessary to make calculations using the same formula, but using different sets of values for the variables. It is possible to obtain a solution by use of a slide rule or by preparing a table giving the solution of the formula resulting from successive changes of each variable. However, in the case of formulas involving several mathematical operations, the labor entailed would usually be very great.
It is possible to avoid aJI this labor by using a diagram representing the formula, in which each variable is represented by one or more graduated lines. l<'rom this diagram, the solution of the formula for any given variable may be read by means of an index line. A diagram of this type is known as a nomogram.
Much of the information needed to solve aeronautical problems will be presented in nomogram form. Instruction manuals for the various aircraft contain numerous nomograms, many of which
. , r
-, ·~·
(a) Bar graph
( c) Broken line graph
1955 ++
1960 +++
1965 +++++
( b) Pictograph
( d) Continuous curved-line graph
( e) Circle graph
FIGURE 1-20. Types of graphs.
100
90
~ r--,..._ I 80 - 70
] 60 .,
~
" 50 1 40 & 30
20
10
0 SL 1
-,....
… r--....
' "-
2345678 Altitude X 1000 h
'
9 10
FIGURE 1-21. Horsepower vs. altitude chart.
appear quite complex. Many of the presentations will possess several curves on the same coordinate axis, each curve drawn for different constants in the equation. In the latter case, it is essential to select the proper curve for the desired conditions.
0 SL 1
Again, as with the simpler graphs, it is more important for the mechanic to be able to read nomograms than it is to draw them.
The following example is taken from the maintenance manual for the Allison 501-DI3 turboprop
engine. A nomogram (figure 1-22) is used to determine the power requirements when the engine is operating at minimum torque. The OAT (outside air temperature), station barometric pressure, and engine r.p.m. are three factors that must be known to use this particular nomogram.
EXAMPLE
Determine the calculated horsepower of a certain engine, using the nomogram in figure l-22. Assume that the OAT is 10° C., the barometric pressure is 28.5 in. Hg, and the engine is operating at 10,000 r.p.m.
FIRST: Locate the reference points on the OAT scale and on the barometric pressure scale that correspond to the given temperature and pressure readings. These are identified as (0 and ®, respectively, on the chart. With the aid of a straightedge, connect these two points and establish point ® on the pivot line.
NEXT: Locate the engine speed, identified as @, on the engine speed r.p.m. scale. Using a straightedge, connect points ® and © and establish point ® on the calculated horsepower scale. The calculated horsepower is read at point ®· The calculated horsepower is 98%.
l ., •.,
MODEL 501-Dl3 ENGINE AND MODEL 606 PROPELLER
MODEL 501-Dl3 ENGINE AND MODEL 606 PROPELLER
CALCULATED TORQUEMETER OUTSIDE AIR (READING) HORSEPOWER TEMP ENGINE SPEED PIVOT BAROMETRIC RPM ·c •F PRESSURE - IN. HG LINE
140 10500 -10 32.0
-20 130 31.0 10400 0 -15 NOTE: VALID FOR WINDS 120 30.0
BELOW 11 M. P. H. 10300 10 ® -10 29.0 110 20 10200 -5 28,0
0 30 --
27.0 10100 "° --- … … °' … 40 26.0 .. 5 -- - 10000 I _, … © 10 50 25.0 9900 15 60 80 24.0
-20 130 31.0 10400 0 -15 NOTE: VALID FOR WINDS 120 30.0
20 9800 70 23.0
25 70 80 22.0 9700
30 90 EXAMPLE 35 21.0 9600 100 60 40 110 55 20.0 9500
FIGURE 1-22. Power requirements at minimum torque.
MEASUREMENT SYSTEMS
Our customary system of measurement ( figure 1-23) is part of our cultural heritage from the days when the thirteen colonies were under British rule. It started as a hodge·podge of Anglo-Saxon, Roman, and Norman-French weights and measures. Since medieval times, commissions appointed by various English monarchs had reduced the chaos of measurement by setting specific standards for some of the most important units. Early records, for instance, indicate that an inch was defined as the length. of "three barleycorns, round and dry" when laid together; a pennyweight, or one-twentieth of a Tower ounce, was equal to 32 wheatcorns from
MEASUREMENT SYSTEMS
the "midst of the ear."
The U.S. gallon is the British wine gallon, standardized at the beginning of the 18th century (and about 20 percent smaller than the Imperial gallon that the British adopted in 1824 and have since used to measure most liquids).
In short, as some of the founders of this country realized, the customary system was a makeshift based largely on folkways.
LENGTH MASS VOLUME
LENGTH MASS VOLUME
METRIC
Meter Kilogram Liter
CUSTOMARY
inch ounce fluid ounce
foot pound teaspoon
year ton tablespoon
fathom grain cup
rod dram pint
mile quart
gallon
barrell
peck
bushel
Metric System
The metric system is the dominant language of measurement in use today. Most of the world countries used the metric system prior to World War II. Since the war, more countries have converted or are in the process of converting to the metric system. Only the United States and 13 smaller countries have not made the conversion.
Congress has the power to define the standa~d of weights and measures. Repeated~y the metnc system has been proposed and each time the question has been voted down.
The metric system was developed by a French statesman, Talleyrand, Bishop of Autum, using a "meter" as a standard; the meter being a specific portion of the circumference of the earth at the equator. From this base measurement the meter was developed and accepted as the standard. Divisions and multiples of the meter are based on the
decimal system.
ELECTRIC TEMPJ,RATURE CURRENT TIME
ELECTRIC TEMPJ,RATURE CURRENT TIME
Celsius
(Centigrade) Ampere Second
Fahrenheit ampere second
FIGURE l-23. Some common units.
- '. 1
'·' .
The Logic of Metric
No other system of measurement that has heen actually used can match the inherent simplicity of International Metric. It was designed ·deliberately to fill all the needs of scientists and engineers. Laymen need only know and use a few simple parts of it. It is logically streamlined, whereas other system:c. developed more or less haphazardly. At this time there are only six base units in the lntC'rnational ~·fetric System. The unit of length is the meter. The unit of mass is the kilogram. The unit of time is the second. The unit of electric current is the ampere. The unit of temperature is the kelvin ( which in common use is translated into the dPgree Celsius, formerly called degree centigrade). The unit of luminous intensity is the candela.
All the other units of measurement in the International Metric System are derived from these six ba:-.e units. Area is measured in square meters; speed in meters per second; density jn kilograms per cubic meter. The newton, the unit of force, i,- a simple relationship involving meters, kilograms, an<l second.<-; and the pascal, unit of pressure, is d~fowd as one newton per square meter. In some other cas(~S. the relationship between the derived and base units must he expressed by rather more cotnplicatcd formulas-which is inevitable in any rncasurcmc11t system, owing to the innate complexity of some of the things we measure. Similar relationship:-. among mass, area, time and other quanlitics in the customary system n:-.ually require s.irnilar formulas, made all the more complicated because they can contain arbitrarv constants. For (·xcrniple, 0;1c horsepower is dcfi~ed as 550 foot.
pound~ per second.
The third intrinsic a<lvantB.ge is that metrjc is based 011 the decimal system. }lultiples and sub- Jllultiplcs of any given unit are always related by power~ of .l 0. For instance1 there are 10 millimC'tf'rs in one centimeter; ] 00 centimeters in one mPtPr; and l,000 meters in one kilometer. This greatly simplifies converting larger to smaller measurements. For example1 in order to calculate the number of meters in 3.794 kilometers, multiply by 1,000 ( move the decimal point three places to the right) and the answer is 3,794,. For comparison. in order to find the number of inches in 3.794, miles. it is necessary to multiply first Ly 51280 and then by 12.
l\.Toreover, multiples and submultiples of all the T ntnnational Metric units follow a consistent narn· ing schrmP. 1vhich consists of attaching a prefix to
the unit 1 whatever it may be. For example, kilo stands for 1,000: one kilometer equals 1,000 meters, and one kilogram equals 1,000 grams. Micro is the prefix for one millionth: one meter equals one rniIIion micrometers, and one gram equals one million micrograms ( figure 1-24).
PREFIX
tera ( 1012 )
giga (10')
mega ( 10')
kilo ( 10')
hecto ( 10')
MEANS
One trillion times
One billion times
One million times
One thousand times
One hundred times
dee a ( 10) Ten times ·------· -------·------- deci (I0- 1 } One tenth of
centi ( 10- 2 } One hundredth of
milli ( 10- 3 ) One thousandth of
micro ( 10- 6 ) One millionth of
nano ( l0- 9 ) One billionth of
pico ( 10- 12 ) One trillionth of
F1cun:E ]-2·1,. 1\ames and symbols for metric prefixes.
Conversion: Metric To Conventional
People tend to resist changes, usually because they do not under_c:.tand either the purpose of the cban~e or the new order. Terminology for customary units and metric units have been discussed. A conversion table also has been included. Examples of its use follow:
To convert inches to millimeters, multiply the number of inches hy 25. (Ex. 25 into mm=25 X25=625 mm)
To convert miUimeters to inches multiply millimeters by .01. ( Ex. 625 mm X .04 = 25 inches.)
To convert square
multiply by 6.5. sq. cm.)
inches to square centimeters
(Ex. 100 sq. in.X6.5=650
To convert square centimeters to square inches multiply by .16. (Ex. lOOX.16=16 sq. in.)
IF YOU WHEN YOU KNOW: YOU CAN FIND: MULTIPLY BY:
LENGTH inches millimeters 25 feet centimeters 30 yards meters 0.9 miles kilometers 1.6 millimeters inches 0.04 centimeters inches 0.4 meters yards 1.1 kilometer miles 0.6
AREA square inches square centimeters 6.5 square feet square meters 0.09 square yards square meters 0.8 square miles square kilometers 2.6 acres square hectometers (hectares) 0.4 square centimeters square inches 0.16 square meters square yards 1.2 square kilometers square miles 0.4 square hectometers (hectares) acres 2.5
MASS ounces grams 28 pounds kilograms 0.45 short tons mega grams ( metric tons) 0.9 grams ounces 0.035 kilograms pounds 2.2 megagrams ( metric tons) short tons 1.1
LIQUID ounces milliliters 30 VOLUME pints liters 0.47 quarts liters 0.95 gallons liters 3.8 milliliters ounces 0.034 liters pints 2.1 liters quarts 1.06 liters gallons 0.26
TEMPERdegrees Fahrenheit degrees Celsius 5/9 ( after subtracting 32) ATURE
degrees Celsius degrees Fahrenheit 9/5 (then add 32)
FIGURE 1-25. Converting customary to metric.
Figure 1-26 is practically self e~planatory. Measurements starting at %4 inch up to 20 inches have
lnchc, ln~h~s MM \!M Fraction, Decimal, Fractions Decimal~ - .0004 .OJ :'.5/32 .781 19.844 - 004 .JO - 7874 20. - OJ 25 51/64 .797 20.241 1/64 0156 .397 13/16 .8125 20.638 - .0197 .50 - .8268 '1 - 0295 .75 53/64 .828 21.034 I/.'32 .0312.5 .794 27/32 844 21.431 - .0394 L .S.5/64 859 21.82/l 3/64 .0~68 1.]9J - 866! 22. .059 1..5 7/8 ,875 ::t2.2:25 1/16 062 1.588 57/M 8906 22.622 5/84 .0781 1.88-1 - .D05:'i 23 - .0787 '
21)/3"2 ')062 2,3.0l!J 3/.'32 094 2 .. 381 ,)\,/f,4 .422 ~3.416 - 0984 2.5 !5/16 .9375 23.813 7/64 mo 2.77/l - .fJ.149 24 . - .1181 .1. 6!/64 .953 24.209 1/)j 125 3.17.5 31/.'32 .96\J 24.fl06 - !.178 3.5 - . 'J843 25 . 9/64 HJ "l.572 6,1/64 9844 25.00.'l 5/32 .156 3.!169 ' !.000 25.400 - 1575 4 - J.0236 :26. 11/64 .172 4.366 1-J/.'32 1.0312 W.l'l4 - .177 4.5 1-1/16 1.062 26.988 3/16 .1875 4.763 - 1.063 Z7 - .1969 5. ] •. 'J/32 1.094 27.781 13/64 ,203 5,]5') - l.102·1 .w - 2165 5.5 I· I//, l.125 2f\ 57;, 7/32 2:19 5 556 - '
1417 c:w 15/M 214 .5.953 1-.5/3~ 1.156 2'l.16'l - .236:?: 6. - I. 1811 )0. 1/4 2,50 fi .. '350 1-3/16 '
1875 llll(i."l - .2,5,5\J S .5 T -7/32 1.219 10.')56 17/64 2656 6.747 - l.220.5 .11 - .27,% 7 1-1/4 1.250 .'"JJ.7.51l 9/32 281 7.lH - l.2,'508 :32 - :?.'l.5.3 7.5 J.<)/32 l.:?.81 .12.,544 19/64 207 7.,541 - J .2'l02 3.1 5/16 .'312 7.938 l-5/16 l.,'31". J.).3,18 .. )15 8. 1.3386 .14 21/64 . 328 8.334 1-11/32 1.344 34.131 - .335 8.5 l-3/8 1.375 34,925 11/32 344 8.731 - 1.1779 .35 - 3543 9. 1-13/32 1.406 35.719 23/64 .359 9.128 - 1.4173 36 - 374 9.5 1-7/16 1.4-18 ,"J6.5t.'3 3/8 .175 9.525 - 1.4567 -17. 25/64 .391 9.022 1-15/32 ].4fl!J 37.306 - .aim JO. - 1.496] .)8. 13/32 .406 10.319 1-1/2 1.500 ::JS.JOO - .41-1 10.5 1-17/32 1.531 38.804 27/64 422 10.716 - !.5354 39. - .4-131 ll 1-9/16 1.362 30.688 7/16 .438 ll.l l3 - l.5748 40. 29/64 453 11.509 1-19/32 1.594 40.481 15/32 469 11.906 - 1.6142 41. - 4724 12, 1-5/8 1.625 41.275 31/64 484 12 .. 103 - 1.651.5 12. - 492 12.5 1-21/32 1.6562 42.06!) ,;2 .500 12.700 l-11/JG 1.6875 4~.86.3 - ,5118 '3 - 1.6929 43 33/64 .5156 13.097 1-2:.1/32 1.719 4.'J.6.56 17/32 5.31 13.484 - !.7323 " 35/64 .547 ]3.801 i .:)/4 1.7,50 44.450 - 5512 14 - J 7717 4.5. 9/16 .563 14.288 1-25/32 J.781 45.244 - .571 14.5 - 1.8110 46. 37/64 578 H.684 1-l.'3/16 1.8125 46.038 - .5006 15 1-27/32 1.844 46.fl31 19/32 594 15.081 1.8.504 47. 39/64 oos 15.478 l-7/8 1.875 47.6:25 5/8 625 15.875 - 1.8898 48 - .6299 JS 1-29/32 1.9062 48 419 41/64 ,6406 16.272 - 1.9291 49. - 6486 16.5 1-15/16 ].,J.375 49.21.1 21/32 .C56 16 669 - l 9685 50 - .669.) 17. J-31/32 Ul69 .50 006 43/64 .672 17.066 ' 2.DOO 50.800 1~,:16 .6875 17.46.1 - 2.007') 51 4,5 f,4 7().'J 17.859 2·1/32 2.03125 .51 5'l4 - 7087 "
- 2 0472 .52 23/,12 719 18 2.'56 2-1116 2.062 52 .. 188 - 728,1 J8 5 - 2.0f\68 53. 47/64 .7:34 Hl.6s.'.l 2--1/32 2.004 .~.).181 - 7480 19. 2-1/8 2.1~5 .5.1.()75 3/4 .750 Hl.050 - 2.126 54. 49/64 7656 19.447 2-5/32 2.156 ,'>4.7ff.l
been converted to decimal divisions of inches and to millimeters.
lnchc, Inch .. , \1).1 MM Fra~tinm D<·c•mals Fractim1s J),.dmals - "2.165 55 3-11/16 3.6875 93.663 :'.-3/16 2. 187,5 55.,563 - 3.7008 '" - 2.2047 56 "l-23/32 3.7Hl 84.456 :'.-7/32 2.219 5(;.356 - ,1.7401 95 - 2.244 S7 l-.1/4 3.7.50 85.2.50 2-1/4 2.2,;o 57.150 - 3.779.5 96. 2-1)/32 2.:'.81 .57.944 3-25/32 3.781 96.()44 - :'..281.5 58. -1-1-'3/16 .'3.812,5 96.838 2-5/16 2.112 58.7,18 - l.8188 97. - 2.:)228 59. 3-27/32 .1.844 87.6,11 2-l 1/,12 2.344 59.531 - 1.858.1 98. - 2.3622 BO. J-7/8 .1.875 98.42,5 2-.318 2,37,) 60.325 - 3.8976 99. - 2.4016 OJ l-2\J/J2 3.8062 99.21\J 2-l:3/32 2.406 61.1 JH - .'3.IJ.170 WO 2·7/!f; 2.4.'38 61.91,1 .}.J.5/lfl 3.().'375 l!10.0J3 - 2.HO\J 62. .'3-11/32 ,3.%:J 100.f'l()fi 2-l.5/1/i 2.468 62.70fl - J.8764 101. - 2.4803 63. 4 4.000 !OJ.HOO 2.(/2 2.500 63 .. 500 4-1/16 4.0fl2 103.188 - 2:.5197 64. 4-1/8 4.125 104.775 2-17/:32: 2.5.'J.l 64.2()4 - 4.1338 105 - 2 .. 559 65. ~--1/16 4.1875 106.363 2·9/l(i 2.562 65.088 4-l/4 4.250 107.!150 2-1\)/.'32 2.594 Wl.881 ·1--5/16 4 .. 112 100 . .538 - 2.S%4 66 - 4.3307 I JO.
2-.5/8 2:.625 M.fi75 4"3/8 4.375 111.125 - :.f),'l8 e7 l-7/16 4.4.18 112.713 :."-21 /.J2 2.fl5(S 67.4E\'l 1-1/2 4_;)00 l 14 .. 100 - 2:.677:?: 6S 4.5275 l l.5. 2-11/16 2.fl875 i>8.2Wl ~-9/16 ·1..562 115.888 - 2.71(15 60 4-5/H 4.625 J 17.475 :?.-2.'J/32 2.718 69.0,5(; 4-1 J /lfl 4.6875 !19.0fi3 2-,1/4 2.7.5() 6fl.f'l50 - ,1 7:':44 l20 - :?..755,J 70 4-:3/4 4.750 120.650 :?.-2'>/12 2.781 70.fl43'1 4-J:J/1(; 4.8125 122 238 - 2.7!153 71 4-7/8 4.875 12,3.825 2.131](; 2.SW) 71.437/i - 4.9212 125. - 2 8346 72 4-1')/lfl 4.9.175 125.413 2-27/32 2 844 72.2314 5 5.000 127 000 - 2.8740 73 . - 5.1181 130. 2-7/8 2x:-s 73.02S .5-1/4 .5.250 1.13.350 2-2\)/32 2.9002 73.819 .5-1/2 5.500 13H.700 - 2.!1114 74. - 5.518 140 2-15/16 :?.
0375 74.611 .5-1/4 5 750 146.050 - 2.U,527 75 - 5.9()55 150 2-31132 2.869 75 406 (; 6.()00 152.400 - 2.9\J:?.J 76 6-1/4 {l.2.50 1,58.750 3 3.000 76.200 - 6.2!1()2 160. '3-1/12 2.0.112 76.9!.J.~ fl-1/2 R.500 165.100 - l.0,)15 77. - 6.6929 170. 'J-1/16 .1.062 77.7S8 {l-3/4 6.750 171.450 - 3.0"iM 78 7 7.000 177.800 3-3/32 3.094 78.581 - 7.0866 UlO. - 3.1 Hl2 78 - 7.4fl03 ]90 J-1/8 3.12.5 70.375 7-1/2 7.500 !fJ0.,500 - . 3.1486 80 - 7.8740 200 . 3-5/32 'l.J.56 80.169 8 8.000 20.3.2(){) 3-.1/Tfi 3.lll75 80.00~J - 8.2677 210, - .1.1880 81. 8-1/2 8.5DO 215.900 "l-7 /12 .1.ZHJ 81.7.58 - 8.(,614 220. - .}.228.3 SC ,, n.r100 228.600 l-1/4 .1.25() s2.s5n - 'l.0551 230 - 1.2n77 8.1. - ').4488 240. l-\j/32 3.28! 83.344 !J-1/2 0.500 241.300 3 .')Oil 84. - 9.842,5 250. 3-5/16 3.312 84.1.177 '" I0.000 254.001 .3-11/,12 3.341 84.8314 10.2162 260. - .1.3464 85. .. JO 6299 :?:70. ->-V8 .1.375 83.72~ " 11.000 279.4111 - .'3.3858 "'
- 11.0236 280. .).\.3/,12 3.406 86 .. 5!\J - 11.4173 290, - 3.42,52 87. - 11.8110 100. 3-7/16 3.438 ~7.313 12 12.000 :J04.8{JJ - 3.4646 88. ,1 13.000 .130.2n1 3-15/.32 J.4fl0 8f!.l06 - 13.7795 350. .3-1/2 ., 500 88 'll"lO '4 1.1.000 3.'>.5.601 - 3 .. )0,')9 fl9. \.5 15.000 381.001 .'3-17/32 .1.5.11 fl'l.694 - 15.7-180 400. .1.5433 80 rn 16.000 l06.40] l-'J/16 .'l.562 00 4877 '7 17.000 43U;GJ - 1.5fl27 91 - 17.7165 450 3-19/.)2 .1.594 91.281 rn 18.000 457.201 - 3.622 92 HJ rn.ooo 482 601 3-.'5/8 3.625 92.075 - 18.63,50 500 ,1-21/.'32 3 656 02.869 20 20.000 .508.001 - .1.1m14 91.
FIGl~RE 1-26. Fractions, decimals, and millim('ters.
FUNCTIONS OF NUMBERS
FUNCTIONS OF NUMBERS
The Functions of Numbers chart (figure 1-27) is included in this chapter for convenience in mak-
No. Square Cube
Square
Root
1 1 1 1.0000 2 4 8 1.4142 3 9 27 1.7321 4 16 64 2.0000 5 25 125 2.2361 6 36 216 2.4495 7 49 343 2.6458 8 64 512 2.8284 9 81 729 3.0000 10 100 1,000 3.1623 11 121 1,331 3.3166 12 144 1,728 3.4641 13 169 2,197 3.6056 14 196 2,744 3.7417 15 225 3,375 3.8730 16 256 4,096 4.0000 17 289 4,913 4.1231 18 324 5,832 4.2426 19 361 6,859 4.3589 20 400 8,000 4.4721 21 441 9,261 4.5826 22 484 10,648 4.6904 23 529 12,167 1.7958 24 576 13,824 4.8990 25 625 15,625 5.0000 26 676 17,576 5.0990 27 729 19,683 5.1962 28 784 21,952 5.2915 29 841 24,389 5.3852 30 000 27,000 5.4772 31 1,961 29,791 5.5678 32 1,024 32,768 5.6569 33 1,089 35,937 5.7446 34 1,156 39,304 5.8310 35 1,225 42,875 5.9161 36 1,296 46,656 6.0000 37 1,369 50,653 6.0828 38 1,444 54,872 6.1644 39 1,521 59,319 6.2450 40 1,600 64,000 6.3246 41 1,681 68,921 6.4031 42 1,764 74,088 6.4807 43 1,849 79,507 6.5574 44 1,936 85,184 6.6332 45 2,025 91,125 6.7082 46 2,116 97,336 6.7823 47 2,209 103,823 6.8557 48 2,304 110,592 (i.9282 49 2,401 117,649 7.0000 50 2,500 125,000 7.0711
ing computations. Familiarization with the various parts of this chart will illustrate the advantages of using "ready-made" computations.
Cube Circum- Root ference Area
1.0000 3.1416 0.7854 1.2599 6.2832 3.1416 1.4422 9.4248 7.0686 1.5874 12.5664 12.5664 1.7100 ]5.7080 !9.635 1.8171 18.850 28.274 1.9129 21.991 38.485 2.0000 25.133 50.266 2.0801 28.274 63.617 2.1544 31.416 78.540 2.2240 34.558 95.033 2.2894 37.699 113.10 2.3513 40.841 132.73 2.4101 43.982 153.94 2.4662 47.124 176.71 2.5198 50.265 201.06 2.5713 53.407 226.98 2.6207 56.549 254.47 2.6684 59.690 283.53 2.7144 62.832 314.16 2.7589 65.973 346.36 2.8020 69.115 380.13 2.8439 72.257 415'.48 2.8845 75.398 452.39 2.9240 78.540 490.87 2.9625 81.681 530.93 3.0000 84.823 572.56 3.0366 87.965 615.75 3.0723 9!.106 660.52 3.1072 94.248 706.86 3.1414 97.389 754.77 3.1748 100.53 804.25 3.2075 103.67 855.30 3.2396 106.81 907.92 3.2717 109.96 962.11 3.3019 IJ.3.10 1,017.88 3.3322 116.24 1,075.21 3.3620 119.38 1,134.11 3.3912 122.52 1,194.59 3.4200 125.66 1,256.64 3.4482 128.81 1,320.25 3.4760 131.95 1,385.44 3.5034 135.09 1,452.20 3.5303 138.23 1,520.53 3.5569 141.37 1,590.43 3.5830 144.51 1,661.90 3.6088 147.65 1,734.94 3.6342 J.50.80 1,809.56 3.6593 153.94 1,885.74 3.6840 157.08 1,963.50
FIGERE 1-27. Functions of numbers.
' . '
.'.;~
Numbers
The number column contains the numbers 1
Square No. Square Cube Root
51 2,601 132,651 7.1414 52 2,704 140,608 7.2111 53 2,809 148,877 7.2801 54 2,916 157,464 7.3485 55 3,025 166,375 7.4162 56 3,136 175,616 7.4833 57 3,249 185,193 7.5498 58 3,364 195,112 7.6158 59 3,481 205,379 7.6811 60 3,600 216,000 7.7460 61 3,721 226,981 7.8102 62 3,844 238,328 7.8740 63 3,969 250,047 7.9373 64 4,096 262,144 8.0000 65 4,225 274,625 8.0623 66 4,356 287,496 8.1240 67 4,489 300,763 8.1854 68 4,624 314,432 8.2462 69 4,761 328,509 8.3066 70 4,900 343,000 8.3666 71 5,041 357,911 8.4261 72 5,184 373,248 8.4853 73 5,329 389,017 8.5440 74 5,476 405,224 8.6023 75 5,625 421,875 8.6603 76 5,776 438,976 8.7178 77 5,929 456,533 8.7750 78 6,084 474-,552 8.8"318 79 6,214 493,039 8.8882 80 6,400 512,000 8.9443 81 6,561 531,441 9.0000 82 6,724 551,368 9.0554 83 6,889 571,787 9.1104 84 7,056 592,704 9.1652 85 7,225 614,125 9.2195 86 7,396 636,056 9.2376 87 7,569 638,503 9.3274 88 7,744 681,472 9.3808 89 7,921 704,969 9.4340 90 8,100 729,000 9.4868 91 8,281 753,571 9.5394 92 8,464 778,688 9.5917 93 8,649 804,357 9.6437 94 8,836 830,584 9.6954 95 9,025 857,375 9.7468 96 9,216 884,736 9.7980 97 9,409 912,673 9.8489 98 9,604 941,192 9.8995 99 9,801 970,299 9.9499 100 10,000 1,000,000 10.0000
through 100. The other columns contain computations for each number.
Cube Circum- Root ference Area
3.7084 160.22 2,042.82 3.7325 163.36 2,123.72 3.7563 166.50 2,206.18 3.7798 169.65 2,290.22 3.8030 172.79 2,375.83 3.8259 175.93 2,463.01 3.8485 179.07 2,551.76 3.8709 182.21 2,642.08 3.8930 185.35 2,733.97 3.9149 188.50 2,827.43 3.9365 191.64 2,922.47 3.9579 194.78 3,019.07 3.9791 197.92 3,117.25 4.0000 201.06 3,126.99 4.0207 204.20 3,381.31 4.0412 207.34 3,421.19 4.0615 210.49 3,525.65 4.0817 213.63 3,631.68 4.1016 216.77 3,739.28 4.1213 219.91 3,848.45 4.1408 233.05 3,959.19 4.1602 226.19 4,071.50 4.1793 229.34 4,185.39 4.1983 232.48 4,300.84 4.2172 235.62 4,417.86 4.2358 238.76 4,536.46 4.2543 241.90 4,656.63 4.2727 245.05 4,778.36 4.2908 248.19 4,901.67 4.3089 251.33 5,026.55 4.3267 254.47 5,153.00 4.3445 257.61 5,281.02 4.3621 260.75 5,410.61 4.3795 263.89 5,541.77 4.3968 267.04 5,674.50 4.4140 270.18 5,808.80 4.4310 273.32 5,944.68 4.4480 276.46 6,082.12 4.4647 279.60 6,221.14 4.4814 282.74 6,361.73 4.4979 285.88 6,503.88 4.5144 289.03 6,647.61 4.5307 292.17 6,792.91 4.5468 295.31 6,939.78 4.5629 298.45 7,088.22 4.5789 301.59 7,283.23 4.5947 304.73 7,389.81 4.6104 307.88 7,542.96 4.6261 311.02 7,697.69 4.6416 314.16 7,853.98
FIGURE 1-27. Functions of numbers (continued).
Square
Square is the prO'duct obtained by multiplying a number by itself: lXl=l, 2X2=4, 17Xl7=289, Squaring may be considered a special form of area
computation: Area= Length multiplied by Width, A=LXW,
Cube
Cube is the product obtained by multiplying a number by itself, then multiplying that product by the number again: lXlXl=l, 2X2X2=8, 13 X 13 X 13 =2,197, Cubing may be considered a specialized form of volumn computation: Volume= Length multiplied by Width by Heigh th, V=LXWXH.
Square Root
Square root is the opposite of a "squared" number. The square root of a number is, that number which when multiplied by itself (squared) will produce the original or desired number: For example, the square root of 1 is 1, 1 X 1 = l. The square root of 4 is 2. The square root of 24 is 4.8990. If an area of 24 square inches must be a perfect square, the length of each side would be 4.8990 inches.
Cube Root
A cube root is the opposite of a "cubed" number. The cube root of a number is that number which
when multiplied by itself (cubed) will produce the original or desired number. The cube root oJ 1 is 1, 1 X 1 X l = 1. The cube root of 27 is 3, 3X3X3=27. If a container of 100 cubic inches and cubic in shape is desired, then the length of each side would be 4.6416.
Circumference of A Circle
Circumference is the linear measurement of the distance around a circle. The circumference is calculated by multiplying the diameter of the circle by the constant 3.1416 (.,,). This constant was calculated by dividing the circumference of circles by their ·diameter. For example, diameter=!, circumference=3.1416, 1X3.1416=3.1416. Diameter=lO, 10X3.1416=31.4160, diameter=l2, 12X3.1416=37.699.
Area of A Circle
Area of a circle is the number of square units of measurement contained in the area circumscribed by a circle of the diameter of the listed number. This is calculated by the formula ( ,,-) X r' = a,
( ,r) multiplied by the radius squared equals area. The radius is equal to one half the diameter. For example, diameter=2, radius= 1. 3.1416X 1 = 3.1416 square units in a circle which has a diameter of 2. Another example, diameter =4, radius= 2. 3.1416X2'=3.1416X4,=12.5664 square units. lion micrograms.
PRINTS
The exchange of ideas is essential to everyone, regardless of his vocation or position. Usually, this exchange is carried on by the oral or written word; but under some conditions the use of these
alone is impractical. Industry discovered that it could not depend entirely upon written or spoken words for the exchange of ideas because misunderstanding and misinterpretation arose frequently. A written description of an object can be changed in meaning just by misplacing a comma; the meaning of an oral description can be completely changed by the use of a wrong word. To avoid these possible errors, industry uses drawings to describe objects. For ·this reason, drawing is called the Draftsman's Lan-
guage.
Drawing, as we use it, is a method of conveying ideas concerning the construction or assembly of objects. This is done with the help of lines, notes, abbreviations, and symbols. It is very important that the aviation mechanic who is to make or assemble the object understand the meaning of the different lines, notes, abbreviations, and sym~ bols that are used in a drawing. (See especialJy ~rThe Meaning of Lines" section of this chapter.)
Prints are the link between the engineers who design an aircraft and the men who build, main~ tain, and repair it. A print may be a copy of a working drawing for an aircraft part or group of parts, or for a design of a system or group of systems. They are made by placing a tracing of the drawing over a sheet of chemically treated paper and exposing it to a strong light for a short period of time. When the exposed paper is developed, it turns blue where the light has penetrated the transparent tracing. The inked lines of the tracing, having blocked out the light, show as white lines on a blue background. Other types of sensitized paper have been developed; prints may have a white background with colored lines or a colored background with white lines.
CHAPTER 2
CHAPTER 2
AIRCRAFT DRAWINGS
A print shows the various steps required in building anything from a simple component to a complete aircraft.
WORKING DRAWINGS
Working drawings must give such information as size of the object and all of its parts, its shape and that of all of its parts, specifications as to the material to be used, how the material is to be finished, how the parts are to be assembled, and any other information essential to making and assembling the particular object.
WORKING DRAWINGS
Working drawings may be divided into three classes: (1) Detail drawings, (2) assembly drawings, and (3) installation drawings.
Detail Drawing
A detail drawing is a description of a single part, given in such a manner as to describe by Jines, notes, and symbols the specifications as to size, shape, material, and methods of manufacture that are to be used in making the part. Detail drawings are usually rather simple; and, when single parts are sma1l, several detail drawings may be shown on the same sheet or print. (See detail drawing at the top of figure 2-1.)
Assembly Drawing
An assembly drawing is a description of an object made up of two or more parts. Examine the assembly drawing in the center of figure 2-l. It describes the object by giving, in a genera] way, the size and shape. Its primary purpose is to show the relationship of the various parts. An assembly drawing is usua11y more complex than a detail drawing, and is often accompanied by detail drawings of various parts.
NOTE:
-ALL BEND RADII 3/16
-ALL BEND RADII 3/16
-RADIUS OF CUT OUT
- IS 1/4
-L.H. IS SHOWN
-R.H.-! OPPOSITE 4 3/8 1 DETAILS
i-= 2-3/18 :Ct
MATERIAL
-024 24ST ALCLAD
4 1/8 ASSEMBLY 3 J/2
, ,
5/16
SYM.
81219AD4 RIVETS 12 REQ,
2 PLATE .064 24ST ALCLAD I REQ.
36-31290 SIDE I REQ 36-31290 SIDE I REQ.
4---- FORWARD I I I
4---- FORWARD I I I
I
I I I I INSTALLATION
I I I I I I I
STA
167
FIGVRE 2-l. Working drawings.
Installation Drawing
An installation drawing is one which includes all necessary information for a part or an assembly of parts in the final position in the aircraft. It shows the dimensions necessary for the location of specific parts with relation to tP,e other parts and reference dimensions that are helpful in later work in the shop. (See installation drawing at the bottom of figure 2-1.)
CARE AND USE OF DRAWINGS
CARE AND USE OF DRAWINGS
Drawings are both expensive and valuable; consequently, they should be handled carefully. Open drawings slowly and carefully to prevent tearing the paper. When the drawing is open, smooth out the fold lines instead of bending them backward.
To protect drawings from damage, never spread them on the floor or lay them on a surface covered with tools or other objects that may make holes in the paper. Hands should be free of oil, grease, or other unc1ean matter than can soil or smudge the print.
Never make note-s or marks on a print, as they may confuse other persons and lead to incorrect work. Only authorized persons are permitted to make notes or changes on prints, and they must sign and date any changes they make.
W'hen finished with a drawing, fold and return it to its proper place. Prints are folded originally in a proper size for filing, and care should be taken so that the original folds are always used.
Continue reading ↓ 120 of 1767 passages shown