AC 33-2B Aircraft Engine Type Certification Handbook
Contains guidance relating to type certification of aircraft engines which will constitute acceptable means, although not the sole means, of compliance with the Federal Aviation Regulations.
This document is cancelled. It may have been replaced. Check the official source before relying on it.
U.S.Department of Transportation Circular Federal Aviation u Administration
FAR GUIDANCE MATERIAL
Subject: AIRCRAFT ENGINE TYPE Date: 06/30/93 AC No: 33-28 CERTIFICATION HANDBOOK Initiated by: ANE-110 change:
1. PURPOSE. This advisory circular (AC) provides methods acceptable to the Administrator for showing compliance with the . type certification requirements of aircraft engines in Part 33, inclusive through amendment 12, of the Federal Aviation Regulations (FAR). The procedures and guidance material provided in this AC may be used by an applicant seeking issuance of a type certificate, an amended type certificate, or a supplemental type certificate for the initial approval of a new type design, or a change in the type design. Consideration will be given to any other method of compliance the applicant elects to present. This information is not in itself mandatory, but serves as a guide to engine manufacturers, engine modifiers, and Federal Aviation Administration (FAA) engine type certification engineers. Individuals should be guided by the intent of the methods provided in this AC.
FAR GUIDANCE MATERIAL
2. CANCELLATION. This revision supersedes AC 33-2A, "Aircraft Engine Type Certification Handbook,tt dated June 5, 1972.
3. RELATED FAR SECTIONS. FAR Parts 21, 23, 25, 27, 29, 33, and 45.
4. RELATED READING MATERIAL. FAA Order 8100.5, "Aircraft Certification Directorate Procedures,'t dated October 1, 1982; and FAA Order 8110.4, "Type Certification," dated December 28, 1967 (Consolidated with Changes 1 through 23, June 1985).
5. BACKGROUND.
AC 33-2A, dated June 5 1972, was published as the llAir%aft Engine Type CertificAtion Handbook." The material therein principally addressed guidance on the procedural aspects of Part 21, but offered very little guidance for Part 33. However, the last sentence of the paragraph did state, l@PURPOSEIV 'IThe remaining chapters of the handbook pertaining to the design and testing of turbine and reciprocating engines will be issued as they become available.n
b. This revision updates and presents the existing procedural information within Chapter 2, and incorporates, within Chapter 3, -
engine type certification rules and guidance material which has since been developed. The appendixes provide turbine and reciprocating engine model descriptions, an index of guidance material and references, and a glossary of acronyms and
1-pJA’C;;’ -c f. SAIN Manager, Engine and Propeller Directorate Aircraft Certification Service
-
ii
CONTENTS
Paraqraph Paqe
CHAPTER 1. INTRODUCTION
CHAPTER 1. INTRODUCTION
1 General 1
2 Guidance 1
CHAPTER 2. GENERAL TYPE CERTIFICATION PROCEDURES
3 Purpose 3
4 Type Certificate 3
5 Type Certification of Aircraft Engines 3
6 Type Certificate Data 4
7 Type Certificate Data Sheet (TCDS) 5
8 Data Required 14
9 Installation Considerations of Engines 18
10 Engine Changes Which Affect Installations 19
10 Engine Changes Which Affect Installations 19
11 Official Engine Tests 20
12 Approval of Engine Parts and Materials 21
13 Processing Changes in Type Design 21
14 Identification Plate 23
CHAPTER 3. TYPE CERTIFICATION GUIDANCE MATERIAL
Airworthiness (Amendment 33-9)
and Operating the Engine
SECTION 1. SUBPART A--GENERAL
SECTION 1. SUBPART A--GENERAL
15 Section 33.3, General 25
16 Section 33.4, Instructions for Continued 25
17 Section 33.5, Instruction Manual for Installing 2%
iii
Paraqraph Paqe
18 Section 33.7, Engine Ratings and Operating 30 Limitations
19 Section 33.8, Selection of Engine Power and 34 Thrust Ratings
SECTION 2. SUBPART B--DESIGN AND CONSTRUCTION; GENERAL
SECTION 2. SUBPART B--DESIGN AND CONSTRUCTION; GENERAL
Cycle Fatigue)
Structure
Turbosupercharger Rotors
20 Section 33.14, Start-Stop Cyclic Stress (Low 37
21 Section 33.15, Materials 39
22 Section 33.17, Fire Prevention 39
23 Section 33.19, Durability 42
24 Section 33.21, Engine Cooling 43
25 Section 33.23, Engine Mounting Attachments and 44
26 Section 33.25, Accessory Attachments 44
27 Section 33.27, Turbine, Compressor, Fan, and 45
28 Section 33.29, Instrument Connection 49
SECTION 3. SUBPART C--DESIGN AND CONSTRUCTION; RECIPROCATING AIRCRAFT ENGINES
SECTION 3. SUBPART C--DESIGN AND CONSTRUCTION; RECIPROCATING AIRCRAFT ENGINES
29 Section 33.33, Vibration 51
30 Section 33.35, Fuel and Induction System 51
31 Section 33.37, Ignition System 52
32 Section 33.39, Lubrication System 52
SECTION 4. SUBPART D--BLOCK TESTS; RECIPROCATING AIRCRAFT ENGINES
SECTION 4. SUBPART D--BLOCK TESTS; RECIPROCATING AIRCRAFT ENGINES
33 Section 33.42, General 53
34 Section 33.43, Vibration Test 53
iv
-
Paraqraph Paqe
54
36 Section 33.47, Detonation Tests 55
35 Section 33.45, Calibration Tests
37 Section 33.49, Endurance Test 55
38 Section 33.51, Operation Test 60
39 Section 33.53, Engine Component Tests 60
40 Section 33.55, Tear Down Inspection 61
41 Section 33.57, General Conduct of Block Tests 61
SECTION 5. SUBPART E--DESIGN AND CONSTRUCTION; TURBINE AIRCRAFT ENGINES
SECTION 5. SUBPART E--DESIGN AND CONSTRUCTION; TURBINE AIRCRAFT ENGINES
42 Section 33.62, Stress Analysis 63
43 Section 33.63, Vibration 63
44 Section 33.65, Surge and Stall Characteristics 63
45 Section 33.66, Bleed Air System 64
46 Section 33.67, Fuel System 64
47 Section 33.68, Induction System Icing 66
48 Section 33.69, Ignition System 68
49 Section 33.71, Lubrication System 69
50 Section 33.72, Hydraulic Actuating Systems 71
51 Section 33.23, Power or Thrust Response 71
52 Section 33.75, Safety Analysis 72
53 Section 33.77, Foreign Object Ingestion 73
54 Section 33.79, Fuel Burning Thrust Augmenter 80
SECTION 6. SUBPART F--BLOCK TESTS; TURBINE AIRCRAFT ENGINES
SECTION 6. SUBPART F--BLOCK TESTS; TURBINE AIRCRAFT ENGINES
55 Section 33.82, General 81
Paraqraph Paqe
56 Section 33.83, Vibration Test 81
Unbalance Tests
Unit (APU) Mode
57 Section 33.85, Calibration Tests 83
58 Section 33.87, Endurance Test 84
59 Section 33.88, Engine Overtemperature Test 92
60 Section 33.89, Operation Test 93
61 Section 33.90, Initial Maintenance Inspection 95
62 Section 33.91, Engine Component Tests 96
63 Section 33.92, Windmilling Tests 98
64 Section 33.93, Teardown Inspection 99
65 Section 33.94, Blade Containment and Rotor 99
66 Section 33.95, Engine-Propeller Systems Tests 100
67 Section 33.96, Engine Tests in Auxiliary Power 101
68 Section 33.97, Thrust Reversers 102
69 Section 33.99, General Conduct of Block Tests 103
70 Section 33.13, Design Features 104
APPENDIXES
APPENDIX 1. Turbine Engine Model Description
APPENDIX 1. Turbine Engine Model Description
References
APPENDIX 2. Reciprocating Engine Model Description
APPENDIX 3. Index of Associated Guidance Material and
APPENDIX 4. Glossary of Acronyms and Abbreviations
vi
CHAPTER 1. INTRODUCTION w
1. GENERAL. This advisory circular (AC) provides procedural and guidance material for the type certification (TC) of aircraft engines. The AC covers certain sections of Parts 21 and 33 of Subchapter C, Chapter 1, Title 14, of the Code of Federal Regulations (CFR). This AC is considered to be a living document. As such, it will be amended on an as-needed basis to maintain currency, such as with the issuance of Part 33 rules changes, or the development of substantive new guidance material.
CHAPTER 1. INTRODUCTION w
2. GUIDANCE. The TC guidance presented is referred to the specific regulatory requirement to which it applies. As a convenience to the user, the FAR Part 33 regulatory requirements, presented in Chapter 3, are reprinted herein to provide a cohesive single-source book for engine type certification; i.e., procedures, rules, and associated guidance. Following each Part 33 section, under "Guidance," is a brief statement of the intent, followed by a listing of documents incorporated as pertinent guidance material; and a second listing of related bibliographic material, followed by specific discussions, where applicable.
-
Chap 1 Par 1 1 (and 2)
CHAPTER 2. GENERAL TYPE CERTIFICATION PROCEDURES
CHAPTER 2. GENERAL TYPE CERTIFICATION PROCEDURES
3. PURPOSE. This chapter provides information and guidance material on the certification procedures of FAR Part 21 which may be employed for engine type certification projects.
4. TYPE CERTIFICATE. The type certificate is defined under FAR Section 21.41.
5. TYPE CERTIFICATION OF AIRCRAFT ENGINES. (Reference FAR Sections 21.13, 21.15, 21.16, 21.17, 21.21, 21.27, 21.29, and FAR Part 33).
a. Enqines Complyinq with Parts 21 and 33. Engines tested and approved to the airworthiness standards of FAR Part 33 are eligible to receive a type certificate. Section 21.13 covers applicant eligibility; Section 21.15 covers application for type certificate; Section 21.16 covers the establishment of special conditions; and Section 21.17 covers designation of the applicable version of Part 33 which should be met.
b. Import Enqines. Section 21.29 prescribes the conditions for eligibility for type certification of import engines.
C. Military Surplus Enqines. Engine type certification may be accomplished for military surplus engines in the same manner as is prescribed in Section 21.21 for other engines, but these engines may also be made eligible for use without being type certificated, in accordance with the provisions of Sections 21.27(c) and (e).
(1) Under Sections 21.27(c) and (e), military surplus engines may be approved for use on military surplus aircraft, if it is shown on the basis of previous military qualifications acceptance and service record, that the engine provides substantially the same level of airworthiness as would be provided if the engine were type certificated under Part 33, with appropriate special conditions and later requirements applied.
(2) The engine characteristics necessary for installation, operation, and identification of the engine should be listed on the pertinent military surplus aircraft type certification data sheet. The following engine technical data are helpful in identifying engine limits and showing compliance with FAR Section 21.27(c):
(i) Military service record summary, including details of mandatory safety changes required for the engine type for military service.
(ii) Military qualification basis, with engine model specifications.
(iii) Military technical orders, comprising manual information for the engine parts list, overhaul, operation, and maintenance.
d. Helicopter Reciprocatinq Enqines. Helicopter reciprocating engines are currently required to meet the specific test requirements of Section 33.49(d), Sections 29.923 and 27.927, or Sections 29.923 and 29.927, as appropriate.
(1) Before this special endurance test was made effective on May 15, 1953, in the Civil Air Regulations (CAR) Part 13, it became evident from service experience that some engines operated in helicopters were hazardous and unreliable, because of the characteristically high steady engine speeds and powers at which overspeeds were often encountered in helicopters.
(2) To provide good reliability in the case of reciprocating engines which were not qualified under Section 33.49(d), or have not been shown to have equivalent capabilities, it is suggested that they be derated. The following method of derating is suggested, as it results in engine ratings which are comparably qualified, as if the helicopter engine test had been the basis for engine qualification:
(i) Limit sea level engines to a maximum power rating (at full throttle), corresponding to an engine speed that is not more than 90 percent of the engine speed at which the original maximum full-throttle power rating was established.
(ii) Limit altitude engines to a maximum power rating of not more than 95 percent of the original maximum power rating, at an engine speed that is not more than 90 percent of the engine speed at which the original maximum power rating was established.
6. TYPE CERTIFICATE DATA. (Reference FAR Sections 21.19 and 21.41). Section 21.19 provides that some types of design changes to engines require a new application for a type certificate.
Engine models which are of the same general series, power leve?; and design characteristics, are usually approved under the same type certificate.
b. A new type certificate is required when the proposed changes in design or limitations are so extensive that a substantially complete investigation of compliance with applicable regulations principle of
is required, operation.
or when the proposed change is in the
lieu
C.
of
The new
use of model
engine model designations,
number prefixes is suggested to
or suffixes, cover many
in changes
--
in engines which are important enough to warrant recognition, but which do not involve considerations necessitating that a new model designation be assigned.
d. New model designations are usually assigned in the following instances:
(1) When interchangeability in a given model aircraft is affected significantly by changes of engine weight or performance.
(2) When propeller mounting, propeller vibration damping, or control provisions are changed so as to preclude use of certain types of propellers on all engines of the same model.
(3) When, as a result of design changes, the horsepower or thrust ratings are changed a significant amount (on the order of 20 percent or more), in excess of the accepted tolerance of output measurement.
(4) When special ratings are granted an existing engine model because of incorporation of new design features.
(5) When a significant change is made in the mounting characteristics of an engine, design of cowling or baffles integral with the engine, exhaust port locations, oil supply sump, accessories, or control characteristics.
.-
(6) When a design change results in significant changes in vibration characteristics, heat rejection through oil or coolant, or other operational characteristics.
(7) When special applications, for example, agricultural use, or extended range operations, result in unique maintenance requirements.
7. TYPE CERTIFICATE DATA SHEET (TCDS). (Reference FAR Section 21.41) The TCDS is part of the type certificate. It includes the type certificate holder, model designation, ratings, limitations, and certification basis. This sheet is prepared by the FAA project engineer, with assistance from the applicant. See FAA Order 8110.4, Paragraph 35, for details on preparations for printing. There is no FAA form provided for TCDSs because of the variations in the required data associated with the various products. The following guidelines provide general information relative to uniform handling of the engine data sheet, with reference to the desired descriptive data content and general arrangement to be considered in the preparation of this sheet.
a. General. Applicable details, as prescribed in following paragraphs, constitute the official status of the engine(s) and serve as a guide for identification, use, and installation of engines in aircraft. The formal arrangement of data, explanatory -
notes, and extent of detail provided should conform, in general, to that shown for the most recently certificated comparable types of engines. Extensive details of engineering installation data are not desirable and this data may be merely referenced. However, specific data should be indicated, if feasible. The assistance of the applicant is desirable in formulating and assuring the accuracy of the data sheets. Standardization of data sheet format is desirable whenever possible, and specifically for the same generic type engines consistent with the following recommendations. The project engineer should have the draft data sheet completed by the time the type certificate is issued.
b. Detailed Description.
(1) Headinq - Numberinq. The data sheet number will appear in the upper right-hand corner of page 1. This number will be the same as the type certificate number. When the data sheet is revised, the revision number will be shown as a suffix. The name of the type certificate holder, in abbreviated form, will be included next, together with all the approved models listed in alphabetical, or numerical, order for reference convenience. The issue date will complete this group. The above information will be enclosed in a box to set it off.
(2) Title. The title of the document (Type Certificate Data Sheet No. ) will appear in the center of the page, after the heading box. The title will include the exact, unmodified, type certificate number, as shown on the type certificate.
(3) Sample Preamble. Engines of models described here that conform with this data sheet (which is a part of Type Certificate No. ) and other approved data on file with the FAA, meet the minimum standards for use in certificated aircraft, in accordance with pertinent aircraft data sheets and applicable portions of the FAR, provided they are installed, operated, and maintained; as prescribed by the FAA approved manufacturer's manuals and other FAA approved instructions.
(4) Type Certificate Holder. Insert the exact name and address of the type certificate holder as shown on the type certificate.
(5) Basic Data. (Main Section).
(i) Model Desiqnation. Show model designations in one or more columns, as necessary to exhibit ratings, limits, or other parameters for each of the models. Reference to recently issued TCDSs will illustrate representative ways of grouping engines in columns, and ways of accomplishing the following instructions.
Chap 2 Par 7
-- ----
---
-- ----
---
--
--
(ii) Type. Describe engine models in terms of major generic features and processes. For example:
(A) Reciprocating - number of cylinders, cylinder arrangement and cooling method, reduction gear ratio, fuel injection, and supercharging (e.g., 9RA, 6HOA, IGO, TSIO);
(B) Turbojet, turbofan - number of compressor and turbine stages, single or multiple spool, radial or axial flow, bypass, etc., (e.g., 12-stage axial flow compressor, reverse-flow annular combustor, four-stage turbine);
(Cl Turboprop, turboshaft - same as in item (B) above, plus free (power) turbine, if appropriate.
(iii) Ratinqs. State certificated maximum power ratings at control setting, rotational speed, pressure altitude, ambient temperature, or other conditions as applicable for the following generic type engines:
(A) For reciprocating engines:
- Maximum continuous horsepower, r.p.m., in. Hg at: Rated pressure altitude ft. -- Sea level pressure altitude ft. S.L.
- Takeoff (5 minutes) horsepower, r.p.m., in. Hg at: Rated pressure altitude ft. -- Sea level pressure altitude ft. S.L.
- Other, if applicable, (e.g., with both low and high impeller gear ratios, anti-detonator injection, or alternate fuels).
(B) For turbojet and turbofan engines:
- Maximum continuous static thrust, lbs. and r.p.m. at sea level.
- Takeoff (5 minutes) static thrust, lbs. and r.p.m. at sea level.
- Other, if applicable, (e.g., with water-alcohol injection, reheat, reverse thrust, or alternate ratings).
(C) For turboshaft and turboprop engines (See Note 1):
Chap 2 Par 7
- Turboshaft Engine Ratings
-- Maximum continuous --- Output shaft --- Output shaft
horsepower, speed, r.p.m.
SHP
-- Takeoff
--- ---
(5 minutes) Output shaft Output shaft
horsepower, speed, r.p.m.
SHP
-- 30-Minute OEI (30 --- Output shaft --- Output shaft
minutes)
horsepower,
speed, r.p.m.
SHP
-- 2-l/2-Minute --- Output --- Output
OEI
shaft shaft
(2-l/2 minutes) horsepower,
speed, r.p.m.
SHP
-- Continuous OEI --- Output shaft --- Output shaft
horsepower,
speed, r.p.m.
SHP
- Turboprop Engine Ratings
-- Maximum continuous --- Output shaft --- Output shaft --- Equivalent --- Jet thrust,
horsepower, SHP speed, r.p.m. shaft horsepower, lb.
ESHP
-- Takeoff
--- --- --- ---
Output shaft horsepower, SHP Output shaft speed, r.p.m. Equivalent shaft horsepower, Jet thrust, lb.
ESHP
-- Other, if and/or reverse
applicable,
thrust).
(e.g., with water-alcohol
power turbine
(iv) Reduction speed; and fan
Gear speed
Ratio.
to low
Output turbine
shaft speed speed.
to
producer governor,
(v) Control System. fuel control, power turbine respectively.
Manufacturer
governor,
and model of and overspeed
gas
(vi) Fuel.
applicable.
(A) Fuel - octane, grade, or type, as
(B) Carburetor, fuel injector, fuel control - manufacturer, model designation, setting, or other relevant information.
(C) Fuel pump (if applicable) - manufacturer and model.
(D) Fuel filtration (if required for fuel at engine inlet) - mesh value.
(vii) giJ.
(A) Oil type or specification.
(B) Oil (sump, dry, or wet) and capacity.
(C) Usable oil - engine in critical positions (degrees from reference).
(viii) Coolant.
(A) Coolant (liquid-cooled engine) type and specification.
(B) Coolant capacity (engine only).
(ix) Iqnition.
(A) Ignition (dual) magnetos or ignition supply box - models.
(B) Timing (degrees BTC).
(C) Spark plugs, igniters, and ignition exciters - models. (If extensive, put into a note).
(x) Compressor - Compression.
(A) Bore and stroke (reciprocating).
(B) Displacement (reciprocating).
(C) Compression ratio (reciprocating).
(D) Turbosupercharger - model.
(xi) Principal Dimensions.
(A) Length (in.) -
Chap 2 Par 7
(B) Width (in.) -
(Cl Height (in.) -
(xii) Weiqht (Dry) Lb. (Note any unusual inclusions or exclusions).
(xiii) Center of Gravity.
(A) Relative to specific longitudinal reference in inches.
(B) Relative to engine center line in inches.
(xiv) Propeller or Power Shaft. Type and size.
(xv) Crankshaft Dampers. Number, order, location, and type.
(xvi) Note List. Listing of note numbers applicable to model group, listed under data column for that group.
(xvii) Leqend. Explanation of symbols.
(A) II--" indicates "same as preceding model."
(B) "-I' indicates "does not apply."
(xviii) Certification Basis.
(A) FAR (CAR), Special Conditions, and Exemptions, as appropriate, effectivity covering type certification of engine.
(B) Engine model and date of type certification application.
(C) Date of type certification.
(D) Date specific models canceled.
(xvix) Production basis. Production certificate number or other production means.
(6) Basic Data. (Notes Section). Variations are so numerous in engine type, and in conditions relative to similar types r that close uniformity in the use of notes for all engines appears impractical. Uniformity for uniformity's sake might well impair the accurate presentation of technical information. The first six notes are assigned to common conditions or parameters and for uniformity should be used solely for these subjects. The remaining notes and contents may be selected according to the data -
to be presented. The following examples of engine data sheet notes are presented accordingly.
(i) Common Note Headinqs Peculiar to All Enqines.
NOTE 1. Engine ratings are based on calibrated stand performance, under the conditions specified by the engine type certificate holder. For example:
- Static sea level standard day conditions (59 OF and 29.92" Hg).
- No customer bleed, no duct losses, no external power extraction.
- Exhaust configuration (as specified by the engine type certificate holder).
NOTE 2. Maximum permissible temperatures or temperature limits.
Maximum Cylinder Head Cylinder Oil inlet Recip. Base (Type Thermocouple) 5-m.) 'F.('C.)
Turbine exhaust gas or turbine inlet
Temperatures measured thermocouples bY -
at . Models Models Takeoff (5 minutes) 'F.('C.) 'F.('C.)
Maximum continuous 'F.('C.) 'F.('C.)
Maximum transient for 'F.('C.) 'F.('C.) accel. ( ) sec.
Maximum transient for 'F.('C.) 'F.('C.) starting ( ) sec.
Other temperature 'F.('C.) 'F.('C.) limits as applicable
NOTE 3. Shaft (or Fan) speed limits.
NOTE 4. Shaft torque limits (or EPR thrust limits).
NOTE 5. Fuel and Oil pressure limits.
NOTE 6. Accessory drive or mounting provisions.
Act.
Drive
Engine RJ 123
Models RJC123
Rotatn Facing Dr Pad
Speed Ratio to Eng
MaxTorq
(in.-lb.) Cont. St.
O'hg Mom.
in-lb
Strtr - * cc -:l - - (#I Strtr - ** cc -:l (#) Gen * ** C -:l (#I * Alt * cc -:l (#) * VacPmp * C etc. etc. etc. (#I FuelPmp etc. etc. etc. (#I Tach etc. etc. (#I PrpGov etc. (#I
I, * 11 - Standard " # " - Drive source 11* * II - Optional " P " - Pneumatic "C " - Clockwise "GP " - Gas Producer rotor "CC " - Counterclockwise "PT " - Power Turbine rotor 11_ II means "does not apply" II--II means "same as previous model"
NOTE 7. Model description - similarities, differences, and special characteristics.
RJ123 - Basic Model - Brief Description.
RJC123 - Similar to RJ123 Except .
List major differences.
NOTE 8. The following accessories are provided as part of the engine (or are optional) and comply with the aircraft installation requirements for (make/model) aircraft. Compliance findings need to be determined, or delegated, by the appropriate FAA Aircraft (or Engine) Certification Office (ACO/ECO).
(ii) Uncommon Notes Peculiar to Reciorocatinq Engines.
NOTE 9. Thrust - tractor or pusher.
NOTE 10. Horizontal or vertical installation - helicopter information.
NOTE 11. Center of gravity tabulation (if not shown in body of data sheet).
NOTE 12. Vibration damper provision limitations.
NOTE 13. Manufacturers bulletins and instructions covering matters of special interest.
NOTE 14. Special ratings.
NOTE 15. Military models note.
NOTE 16. Special equipment.
NOTE 17. Approved propellers - models.
NOTE 18. Other applicable notes.
(iii) Uncommon Notes Peculiar to All Turbine Ensines.
NOTE 9. Rotational velocities at standard and overspeed, .- alternate ratings, etc.
NOTE 18. Bleed air extraction.
NOTE 11. Alternate fuel information.
NOTE 12. Fuel or oil additives.
NOTE 13. Anti-icing, de-icing equipment, requirements.
NOTE 14. Power ratings for non-standard conditions.
NOTE 15. Rotor disk integrity and rotor blade containment (where special provisions apply).
NOTE 16. Operational torques, power settings, and other special limits.
NOTE 17. Engine mount system.
NOTE 18. Power boost, injection.
NOTE 19. Other applicable notes for special equipment, or relating to specific or unique engine installation requirements, such as inlet foreign object protection, lightning protection, HERF protection, thrust reversers,
criticality level of software for engine controls, and other electrical/electronic systems, emissions standards, extended range operations, etc.
(iv) Notes Peculiar to Turboproo Enaines.
NOTE 20. Approved Propellers - Models (when available).
NOTE 21. Engine - Controls.
NOTE 22. Equivalent shaft horsepower - Jet thrust, lb./2.5 + SHP.
(v) Other Notes Peculiar to Special Conditions Assiqned.
(vi) TCDS (For Obsolete Enqines). (Reference FAR Sections 21.15, 21.21, 21.31, and 33.5). When an engine model has become obsolete; e.g., if the type certificate holder does not intend to manufacture it, or any of its component parts; approval under the type certificate may be canceled upon request. After cancellation, it is no longer necessary for the [former] type certificate holder to maintain up-to-date type design and type certificate data. The TCDS of the engine will be revised to reflect the change in certification status and, when all models listed under one type certificate have been canceled, the data sheet will be transferred to a combined listing of obsolete engines. The operation of obsolete engines still in service is eligible to be continued under the status of the approval in effect at the time the certificate was canceled. If reinstatement of the type certificate is desired by the former type certificate holder for the purpose of resuming active engine production, a new application for type certificate, to be based on current FAR, is needed.
8. DATA REOUIRED. (Reference FAR Sections 21.15, 21.21, 21.29, 21.31, 21.41, and FAR Part 33).
FAA Form 8110-12. "Application for Type Certificate" (OMB :4-R0078) is the form referred to in Section 21.15(a). It should be submitted to the FAA Aircraft Certification Office (AC01 r of the region in which the applicant is geographically located.
b. Preliminary Data. Certain technical data are needed to make the initial evaluation of conformity with the specific design requirements and the establishment of detailed qualification testing to be prescribed, in accordance with FAR Part 33. The data most useful for these purposes include a preliminary type design description, technical design data, which are required under Sections 21.21(b) and 21.29(a)(2), together with other useful background information. To facilitate this evaluation of
engine design features, the preliminary data may be submitted along with the application for a type certificate. The following preliminary data are suggested:
(1) A preliminary model description, specification, or equivalent, containing at least sufficient information to permit the establishment of the basis for engine certification.
(2) Drawings showing external views and cross-sections of selected components, reflecting unique and typical detailed features.
(3) A review of significant development history, emphasizing the extent of development experience with the engine, with particular emphasis on unique or complex features, or their combinations not used up to now in aircraft engines.
(4) Proposals for substantiating compliance with the requirements of FAR Part 33 for U.S. applicants' engines and Section 21.29 for import engines, by means of technical analyses or testing. Test proposals are desired appreciably before the proposed starting date of the test, in sufficient detail to serve as a guide for testing, whereupon they may be incorporated in the Type Inspection Authorization (TIA). Reference [Handbook] FAA Order 8110.4 for more detailed information on TIAs, including test article preand post-test conformity inspection and schedule requirements.
C. Final Type Desiqn and Type Certificate Data for U.S. Manufactured Enqines. Acceptable type design and type certificated data, test reports, and computations data, required under Section 21.21(b), cover the engine design that completed the prescribed qualification testing. Acceptable data are described as follows:
(1) Type Desiqn Data. (Reference Section 21.31).
(i) Enqine Model Description. The final model description should provide data and information that is all officially verified, to replace the preliminary model description. (Reference Appendixes 1 and 2).
(ii) Enqine Parts Drawinqs, Material, and Process Specifications. Acceptable data will show the configuration of the type design that successfully complied with the required tests and inspections. A numerically arranged drawing list that shows the latest design change identification is recommended to accompany the drawings. Drawings should be sufficiently detailed to identify and completely describe the design features; supply information on dimensions, materials, and processes necessary to define number
the struc locations;
tural
and
strength any other
of the data
product; necessary
part and to allow,
serial
by
comparison, the determination of the airworthiness of later products of the same type.
(2) Type Certificate Data. (Reference Sections 21.21(b), 21.41, and Part 33).
(i) Test Reports and Computations. Test reports and computations to substantiate compliance with the applicable requirements of Part 33. A test report should cover, but not be limited, to the following:
(A) Test equipment. A complete description with photographs, or reference to a previous report in which the same equipment was used; the manner of engine mounting in the test equipment; and the calibration status of instruments.
(B) Test procedure. The name of the test, part of the test sequence, or the FAR; the chronological log of testing; delays in tests and their causes; stops for minor corrections and servicing engine; and time required for starts.
(C) Test data. Graphs showing variations in operating conditions during the endurance test; log sheets and calibration curves for calibration test data; method used in correcting test data to standard atmospheric conditions (Reference Sections 33.45 and 33.85(a)) and substantiation of any correction factors used.
NOTE: All data should be legible, accurate, and when plotted, use scales which are easily read and interpolated.
(D) Teardown inspection. Describe appearance of parts before assembly and after disassembly, prior to cleaning for dimensional inspection. Describe test results with beforeand after-test tables of dimensions of major parts of the engine that are likely to incur wear, or change of dimension. Include photographs and descriptions of excessively worn parts. Discuss any unusual wear, burning, overheating, part failure or impending failure, and occurrence of heavy deposits on parts. Indicate the condition of mating, sealing, and friction surfaces; e.g., airoil seals, each engine case, valve faces, piston rings, oil seals, curvic couplings, etc. Indicate the results of visual, X-ray, magnetic, fluorescent particle, or other inspections of major parts.
and test.
grades of Identify
(E) Laboratory fuel, lubricants, the specification
analyses. and hydraulic
to which
Analyses
fluids the fluids
of the types used in the conform. Describe the test.
the condition of the lubricant and hydraulic fluids after
16 Chap Par
16 Chap Par
2 8
(ii) Instruction Manual(s). (Reference Section 33.5). The manual(s) cover information for installing, operating, and continued airworthiness of the engine. Installation and operating manual data that have been substantiated, FAA approved, and are specifically required for engine approval in aircraft, should be so indicated. For convenience, such data may appropriately be contained in a separate portion of the manual(s).
d. Type Desiqn and Type Certificate Data for Import Enqines. Certain technical data are required under Section 21.29(a) for import engines when a U.S. type certificate has been applied for. The requirements for such import engines are based on reciprocal airworthiness agreements between the U.S. and the country of manufacture involved, as indicated by Section 21.29. The airworthiness bases, and the exact extent and type of technical data to be supplied the FAA, for showing compliance with the FAA requirements, may vary in accordance with specific agreements
the between the Administrator and the Airworthiness Authority of country of manufacture; but includes the usual application and preliminary data already covered, and usually the following:
(1) Type Desiqn Data. Engine model description as discussed above in paragraph c(1) of this section.
(2) Type Certificate Data.
(i) Certification compliance table.
(ii) Engine manuals, in the English language, described above in paragraph c(2)(ii) of this section. Additionally, if not included in the manuals, engine installation and general arrangement drawings are to be submitted.
(iii) Statement of compliance by the Airworthiness Authority of the country of manufacture, with the applicable airworthiness requirements.
(3) Import Requirements Statement. The following statements should be incorporated on the type certificate data sheet (TCDS) for import engines, immediately before "NOTE 1":
"To be considered eligible for installation on U.S. registered aircraft, each engine to be exported to the United States shall be accompanied by a certificate of airworthiness for export, or certifying statement endorsed by the exporting civil airworthiness authority which contains the following language:
(a) This engine conforms to its United States type design (Type Certificate No.-----) and is in a condition for safe operation.
Chap 2
Par 8 17
(b) This engine has been subjected, by the manufacturer, to a final operational check and is in a proper state of airworthiness. Reference FAR Section 21.500 which provides for the airworthiness acceptance of aircraft engines manufactured outside the U.S., for which a U.S. type certificate has been issued.
Additional guidance is contained in FAA Advisory Circular 21-23, Airworthiness Certification of Civil Aircraft, Engines, Propellers, and Related Products Imported into the United States."
9. INSTALLATION CONSIDERATIONS OF ENGINES. (FAR Section 21.21).
a. General. An engine type certificate may be obtained upon completion of examination of the type design, completing all engine tests, and applying all applicable provisions of FAR Part 33 and Section 21.21. While it is desirable that the engine applicant cater to all possible aircraft installation characteristics, this is not a requirement for engine certification. This does not obviate the desirability of intimately interrelated installation requirements being introduced into an engine characteristics
certification
are known in
program sufficient
when the
time
aircraft to do so.
b. New Enqine. new aircraft may be aircraft installation
New engines expected to requirements.
being developed originally meet Otherwise,
concurrently the applicable interrelated
with
installation changes,
specifically combination
or
requirements may be met by either engine design installation features. Such considerations are related to the engine-aircraft or engine-propeller under consideration and require evaluation either
often
apart from or, at times, after engine certification may have been accomplished. While the aircraft applicant is responsible for showing compliance with the aircraft installation requirements, there are occasions when the engine applicant's substantiation data may be utilized for this purpose. It is recommended, therefore, that at the initial engine type board meeting, the engine applicant establish the extent to which he plans to provide substantiation data for the installation. It then becomes desirable that such data be submitted with the engine type certificate data, for later coordination among FAA ACOs.
C. Enqine Chanqes. The foregoing procedure is for new engine models. Refer to the next section for procedures in handling certain design changes to engines that may require changes to the installation. When components of the installation are provided as
Chap 2
Par 8 18
part of the engine type certification design (e.g., pumps, reversers, coolers, etc.), the engine TCDS should reflect this.
10. ENGINE CHANGES WHICH AFFECT INSTALLATIONS. (FAR Sections 21.19 and 21.97).
a. This section discusses changes in design to certificated engine components whereby the engine operating limits, engine installation details, or aircraft performance characteristics may possibly be significantly altered and require reinvestigation of the aircraft approval. Such major engine changes are to be handled in accordance with Sections 21.19 and 21.97 for engine approval.
b. Extensive changes may result in engine model redesignation, and major changes of a lesser but significant degree may require revisions to the limitation affecting data in TCDSs, operating manuals and/or engine manuals. It is cautioned that seemingly slight changes in engine components may, at times, adversely affect aircraft performance and installation limitations. Some changes that have resulted in certain problems for various engines involve engine fuel metering, surge bleed, and variable geometry control components.
(1) For engine changes, for incorporation in production engines and for general use, that are considered to possibly affect aircraft installations, the degree of compatibility with existing aircraft installation is first established. This involves coordination by the FAA and the engine manufacturer with the responsible aircraft type certificate holder. Suggested procedures are discussed in paragraph 1Oc below.
(2) If engine interchangeability is adversely affected for existing installations, it is desirable that either the engine or aircraft manufacturer initiate remedial modifications, rather than establishing and qualifying a new model of engine. Proposed engine type design changes should be thoroughly reviewed prior to approval, to ensure they are compatible with the aircraft installations in which the engine is being used, as all engines of the same model designation should be interchangeable in the aircraft.
C. To assist the FAA in evaluating engine type design changes for effects on engine interchangeability in existing aircraft, it is suggested that the engine manufacturer coordinate the changes with affected aircraft manufacturers. It is further suggested that the engine manufacturer establish a written procedure whereby they will notify the FAA engine controlling office of the results, after the completed coordination of each affected engine change. Accomplishment of these steps should reasonably assure thorough evaluation of each design and expedite its approval on the aircraft. If any doubt remains concerning the compatibility
status of an engine change, its status should be resolved between the FAA engine and aircraft controlling offices.
11. OFFICIAL ENGINE TESTS. (FAR Section 21.33 and Part 33).
a. Official engine certification tests are to be conducted, in accordance with the authorization directed to the applicant. The tests required for engine certification are as prescribed by pertinent sections of Part 33. The authorization may be a letter or a TIA, in accordance with FAA Order 8120.2A, "Production Approval and Surveillance Procedures," and "TC Handbook," FAA Order 8110.4. Reference these documents and other applicable local FAA Orders, such as NE CD 8110.2A, "Confirmation of Satisfactory Conformity Inspection," and NE CD 8110.1A, "Evaluation and Approval Responsibilities for Manufacturer's Material and/or Process Specifications Specified in the Type Design," when requesting participation of representatives from other than the cognizant FAA engineering office.
b. Witnessing of tests by FAA representatives, as prescribed in Section 21.33, is accomplished, at least, for the engine calibration, endurance, and operation tests; and the teardown inspection following these tests. FAA representatives may also witness such specialized tests as vibration measurement, detonation, rotor integrity, rotor blade containment, icing, and ingestion tests. The engine manufacturer's designated engineering representative (DER) should witness all certification testing and subsequent parts improvement tests conducted by the manufacturer, for the purpose of authenticating the tests and the results. FAA, or delegated designees, must have made a determination prior to testing that engines, parts, and/or components to be tested conform to the appropriate design data.
C. The test authorization identifies the following details relating to official tests:
(1) The engine to be tested and the specific tests, with the schedule of runs and test limits to be employed.
(2) The test equipment, instrumentation (type and accuracy), and facilities (rigs, cells) to be utilized.
(3) The test witnessing desired.
(4) Inspections to be conducted, covering both the engine and the test equipment, as appropriate.
d. For all official FAA tests, test rigs and cells should be inspected for configuration; and data acquisition systems instrumentation for location and calibration.
12. APPROVAL OF ENGINE PARTS AND MATERIALS. (FAR Sections 21.19, 21.113, 21.303, and FAR Part 33).
General. All engine parts and materials which have met the ksign and test requirements of Part 33, for engine type certification, are eligible to be approved parts.
b. Chanqes by Type Certificate Holder. Changes to the type design of the engine may be made by approval granted to the type certificate holder, when he meets the requirements prescribed under Part 33, and Part 21, Subpart D, discussed in paragraph 13 below.
(1) As indicated for major changes, the parts should undergo testing similar to the original substantiation, unless alternate acceptable substantiation is provided. Minor changes do not usually require testing for their substantiation. Experience has indicated that the cumulative effects of both major and minor changes, especially when groups of new changes are incorporated in production engines, may have significant adverse effects on safety or durability.
(2) Therefore, retesting of engines with all recent design changes appears desirable, when incorporating a design change or group of design changes, in order to assess these effects; and may include development, endurance, vibration, and fatigue testing. Submittal of description data is needed for FAA approval, or for DER approval when appropriately authorized.
C. Replacement or Modification Parts Produced by Other Than the Enqine Type Certificate Holder. Design approvals of these parts may be granted as either identical parts to those in the engine type design, or as modifications to the type design. Acceptable means of compliance with Section 21.303 for processing these replacement parts are contained in AC 21.303-l.
(1) When the applicant desires to substantiate parts embodying extensive new design, complete type design data is required, as prescribed in Section 21.19, in the manner applicable to new applications for type certificates.
(2) When the applicant desires to substantiate parts embodying major type design changes, not great enough to require a new application for type certificate, a supplemental type certificate, as prescribed in Section 21.113, may be issued.
13. PROCESSING CHANGES IN TYPE DESIGN. (FAR Part 21, Subparts D and E).
a. Minor Chanqes. Section 21.95 applies to the approval of minor ch a drawing
anges in type comparison
d to
esign. Such substantiate
changes
their
normally airworthiness.
require only Typical
examples of minor changes are included in the list which follows this paragraph. These changes may be approved by the applicant's appropriately authorized DER. An acceptable method of handling these changes includes submitting to FAA the engineering design change notices, where necessary, to fully describe the changes. Intervals between submittal of each new change, or group of changes, should not exceed six months. Consideration should be given to the possibility that, while certain design changes may well be considered minor when evaluated singly, the cumulative influence of a number of such changes may have an adverse effect, and may have to be evaluated as major changes. The following is a list of typical minor changes:
(1) Slight variations in clearances.
(2) Reasonable increase in radius of fillets.
(3) Increase in thickness, where the design permits it, without adverse effects.
(4) Change to equivalent, or improved material, in minor parts.
(5) Improvements in heat treatments of parts, without reducing elongation of parts subjected to high stress.
(6) Small changes in the design of non-critical parts of the engine.
(7) Improvements in the manufacturing, or processing of parts, without reducing the material properties.
b. Major Chanqes. Section 21.97 applies to the approval of major changes in the type design. To substantiate major changes to a certificated engine, substantiating data must be submitted. Typical examples of major changes are included in the list which follows this paragraph. Acceptable substantiating data include, at least, technical data and drawings, together with reports of tests, when applicable. As provided in FAR Part 21, Subpart D, a type certificate holder may apply for amendment of the original type certificate for major changes. As provided in FAR Part 21, Subpart E, applicants other than the type certificate holder may apply for a supplemental type certificate for major changes, when appropriate. The applicant should meet at least the minimum airworthiness standards applicable to the original engine, when qualifying design changes. When an unsafe condition has developed, special substantiation may be required to demonstrate that the unsafe condition has been overcome by the proposed type design change. Changes that will contribute to improved safety are often developed as a result of service experience, and may be approved as constituting the current type design standard in compliance with Section 21.99(b). Major changes may be
recommended for approval appropriately designated service use until approved typical major changes:
by the type certificate holder's DER, but may not be introduced by the FAA. The following is
into
a list of
gear
(1) ratio.
A change of either compression ratio, or supercharger
(2) Establishing increase of a temperature inlet temperature, turbine
the eligibility of engines for either limit, or a speed limit, such as: oil inlet or exhaust gas temperature,
an
cylinder base or head temperature, fan engine minimum idle speed, or power turbine maximum speed.
(3) A change in the material or design of highly stressed parts; either rotating, reciprocating, or non-rotating; likely to adversely affect the airworthiness of such parts.
(4) A change involving the method of clamping or attaching rotating, reciprocating, or non-rotating parts.
(5) Any change that measurably affects the engine's fit, function, or compatibility with existing aircraft installations, such as those defined in the preceding paragraph lob.
(6) Any change to a life-limited part leading to a change of approved life.
(7) Any change providing corrective action for Airworthiness Directives (ADS).
14. IDENTIFICATION PLATE. (FAR Part 33 and Part 45, Subpart B).
a. General. An acceptable method of complying with the fireproof and location requirements of Section 45.11(a) is to meet the following conditions:
a 2,000
(1) The OF flame,
data
for
thereon at least
is legible 15 minutes. after the application of
(2) The engine and engine be easily defaced
plate is located modules for easy or dislodged.
in an accessible viewing, and is
place on the not expected to
b. included to install Section
Identification Data. The type of information to be on the identification plate, and the persons authorized and remove identification plates, are prescribed in 45.13.
C. Identification Plate Attachment. AC 43-17,"Methods, Techniques, Governing
and Practices the Installation,
Acceptable
Removal,
to or
the Administrator Change of Identification
Data and Identification Plates," dated September 5, 1979, is incorporated herein. Compliance with Section 33.19 must be shown, in that the means of attaching the identification plate will not cause cracks, induce fluid leaks, or be susceptible to dislodgement within the interior of the engine, or otherwise adversely affect the engine and module durability, or introduce design features shown to be hazardous or unreliable.
CHAPTER 3. TYPE CERTIFICATION GUIDANCE MATERIAL SECTION 1. SUBPART A--GENERAL
CHAPTER 3. TYPE CERTIFICATION GUIDANCE MATERIAL SECTION 1. SUBPART A--GENERAL
15. Section 33.3, General.
Section 33.3 General:
Each applicant must show that the aircraft engine concerned meets the applicable requirements of this part.
***
Guidance: The INTENT of this section is self-evident.
Incorporations: None.
References: None.
Generally speaking, FAA will approve an applicant's engine within those conditions and limits which are satisfactorily substantiated. The applicant's assumed data and information for the specific engine design, for which type certification is requested, are initially (in part) provided to FAA with submittal of the application for TC. FAA then, and throughout the TC process, evaluates and validates the assumptions by analyses and tests. The conclusions result in statements of ratings, operating limitations, and instructions for continued airworthiness, installing, and operating the engine - all to assure safe operation of the engine in service.
16. Section 33.4, Instructions for Continued Airworthiness.
Section 33.4 Instructions for Continued Airworthiness.
The applicant must prepare Instructions for Continued Airworthiness in accordance with Appendix A to this Part [immediately following] that are acceptable to the Administrator. The instructions may be incomplete at type certification if a program exists to ensure their completion prior to delivery of the first aircraft with the engine installed, or upon issuance of a standard certificate of airworthiness for the aircraft with the engine installed, whichever occurs later.
APPENDIX A TO PART 33 -- INSTRUCTIONS FOR CONTINUED AIRWORTHINESS
APPENDIX A TO PART 33 -- INSTRUCTIONS FOR CONTINUED AIRWORTHINESS
A33.1 GENERAL
(a) This Appendix specifies requirements for the preparation of Instructions for Continued Airworthiness as required by Section 33.4.
(b) The Instructions for Continued Airworthiness for each engine must include the Instructions for Continued Airworthiness for all engine parts. If Instructions for Continued Airworthiness are not supplied by the engine part manufacturer for an engine part, the Instructions for Continued Airworthiness for the engine must include the information essential to the continued airworthiness of the engine.
A33.1 GENERAL
(c) The applicant must submit to the FAA a program to show how changes to the Instructions for Continued Airworthiness made by the applicant or by the manufacturers of engine parts will be distributed.
A33.2 FORMAT
(a) The Instructions for Continued Airworthiness must be in the form of a manual or manuals as appropriate for the quantity of data to be provided. (b) The format of the manual or manuals must provide for a practical arrangement.
A33.3 CONTENT
A33.3 CONTENT
The contents of the manual or manuals must be prepared in the English language. The Instructions for Continued Airworthiness must contain the following manuals or sections as appropriate, and information: (a) Enqine Maintenance Manual or Section. (1) Introduction information that includes an explanation of the engine's features and data to the extent necessary for maintenance or preventive maintenance.
(2) A detailed description of the engine and its components, systems, and installations. (3) Installation instructions, including proper procedures for uncrating, deinhibiting, acceptance checking, lifting, and attaching accessories, with any necessary checks. (4) Basic control and operating information describing how the engine components, systems, and installations operate, and information describing the methods of starting, running, testing, and stopping the engine and its parts including any special procedures and limitations that apply. (5) Servicing information that covers details regarding servicing points, capacities of tanks, reservoirs, types of fluids to be used, pressures applicable to the various systems, locations of lubrication points, lubricants to be used, and equipment required for servicing.
(6) Scheduling information for each part of the engine that provides the recommended periods at which it should be cleaned, inspected, adjusted, tested, and lubricated, and the degree of inspection, the applicable wear tolerances, and work recommended at these periods. However, the applicant may refer to an accessory, instrument, or equipment manufacturer as the source of this information if the applicant shows that the item has an exceptionally high degree of complexity requiring specialized maintenance techniques, test equipment, or expertise. The recommended overhaul periods and necessary cross references to the Airworthiness Limitations section of the manual must also be included. In addition, the applicant must include an inspection program that includes the frequency of the inspections necessary to provide for the continued airworthiness of the engine. (7) Troubleshooting information describing probable malfunctions, how to recognize those malfunctions, and the remedial action for those malfunctions.
(8) Information describing the order and method of removing the engine and its parts and replacing parts, with any necessary precautions to be taken. Instructions for proper ground handling, crating. and shipping must also be included. (9) A list of the tools and equipment necessary for maintenance and directions as to their method of use. (b) Enqine Overhaul Manual or Section. (1) Disassembly information including the order and method of disassembly for overhaul. (2) Cleaning and inspection instructions that cover the material and apparatus to be used and methods and precautions to be taken during overhaul. Methods of overhaul inspection must also be included. (3) Details of all fits and clearances relevant to overhaul.
(4) Details of repair methods for worn or otherwise substandard parts and components along with the information necessary to determine when replacement is necessary.
(5) The order and method of assembly at overhaul. (6) Instructions for testing after overhaul. Instructions for storage preparation, including (7) any storage limits. (8) A list of tools needed for overhaul.
A33.4 AIRWORTHINESS LIMITATIONS SECTION
The Instructions for Continued Airworthiness must contain a section titled Airworthiness Limitations that is segregated and clearly distinguishable from the rest of the document. This section must set forth each mandatory replacement time, inspection interval, and related
A33.4 AIRWORTHINESS LIMITATIONS SECTION
procedure required for type certification. If the Instructions for Continued Airworthiness consist of multiple documents, the section required by this paragraph must be included in the principal manual. This section must contain a legible statement in a prominent location that reads: "The Airworthiness Limitations Section is FAA approved and specifies maintenance required under Sections 43.16 and 91.163 of the Federal Aviation Regulations unless an alternative program has been FAA approved."
***
Guidance:
Instructions service intr
The INTENT of for Continued oduction of the
this
A
section irworthiness engine.
is to are
assure that available prior to
Incorporations: None.
References: None.
The overhaul section, or manual portion of the instructions for continued airworthiness, may not be available at time of type certification of the engine. In such cases, the engine TCDS should incorporate a "NOTE" prohibiting the overhaul of engines until the overhaul instructions are available; and that, meanwhile, the manufacturer may provide rebuilt engines utilizing new engine tolerances. Overhauled engines must deliver, at least, the TC rated powers, or thrusts, within the ratings' associated limitations.
17. Section 33.5, Instruction Manual for Installinq and Operatinq the Enqine.
Section 33.5 Instruction manual for installing and operating the engine.
Each applicant must prepare and make available to the Administrator prior to the issuance of the type certificate, and to the owner at the time of delivery of the engine, approved instructions for installing and operating the engine. The instructions must include at least the following: (a) Installation instructions. (1) The location of engine mounting attachments, the method of attaching the engine to the aircraft, and the maximum allowable load for the mounting attachments and related structure. (2) The location and description of engine connections to be attached to accessories, pipes, wires, cables, ducts, and cowling. (3) An outline drawing of the engine including overall dimensions.
- (b) Operation Instructions. (1) The operating limitations established by the Administrator.
(2) The power or thrust ratings and procedures for correcting for nonstandard atmosphere. (3) The recommended procedures, under normal and extreme ambient conditions for-- (i) Starting; (ii) Operating on the ground; and (iii) Operating during flight.
***
Guidance: The INTENT of this section is to assure that the engine installation and operating instructions are approved by the time the type certificate for the engine is issued.
Incorporations: None.
References: SAE Document ARP 1507, "Helicopter Engine/Airframe Interface Document and Checklist," issued September 1985. This reference offers further guidance on the types and formats of engine installations and operations information. Although this document is oriented to helicopter (turboshaft) engines, it may be useful as additional general guidance to authors of installation and operating instruction manuals. -
a. The installation and operating instructions should incorporate all relevant and complete information on the characteristics, performance, and physical interfaces of the engine. A type certificated engine may include some external lines, equipment mountings, diaphragms, or firewalls which do not meet all certification requirements of some installations. Added line shrouding, relocation of fluid lines, or other changes constitute engine type design changes which may be required for the aircraft installation. Such FAA-approved changes are accomplished preferably by the engine type certificate holder, as approval based on engine compatibility and endurance qualification is usually necessary. However, upon achieving satisfactory coordination with the engine type certificate holder, accomplishment of such changes by the aircraft applicant is often acceptable as an alternative.
b. The engine type certificate holder or applicant may elect to incorporate items of equipment or accessories which are oftentimes handled as part of the aircraft installation responsibility. Examples of such items are engine mounted oil tanks, oil coolers, fuel heaters, generators, thrust reversers, inlet and exhaust nozzles, and various fluid pumps.
(1) When the engine manufacturer elects to furnish such accessories, it is basically implied that he will substantiate
them for engine compatibility, and be responsible for dealing with service difficulties.
(2) If the engine type certificate holder elects to establish aircraft installation compliance, he should develop and provide the necessary installation data in accordance with applicable aircraft requirements.
(3) If the engine type certification effort incorporates findings of compliance for aircraft installation items (i.e., to FAR Part 23, 25, 27, or 29 requirements) then such should be identified on the engine TCDS.
C. The engine installation instructions should incorporate information on the means of limiting, and on the quality of engine compressor bleed air available for airframe use. Design bleed air quality, limit(s), and the means of limiting should be verified by the failure modes and effects analysis and by testing, as appropriate. An example of the need for such information is seen in the certification of FAR Part 23 turbine powered aircraft: Turbine engine bleed air systems of turbine powered airplanes must be investigated to determine that, if the bleed air system is used for direct cabin pressurization, it is not possible for hazardous contamination of the cabin air system to occur in the event of lubrication system failure.
d. The engine installation instructions should incorporate statements of instrumentation types, ranges, required precision, and accuracies for those engine parameters required for safe operation. These statements should be based upon the applicantselected ratings for the specific engine design, as verified and substantiated throughout the type certification process, particularly the block tests.
18. Section 33.7, Enqine Ratinqs and Operatinq Limitations.
Section 33.7 Engine ratings and operating limitations.
(a) Engine ratings and operating limitations are established by the Administrator and included in the engine certificate data sheet specified in Section 21.41 of this chapter, including ratings and limitations based on the operating conditions and information specified in this section, as applicable, and any other information found necessary for safe operation of the engine. (b) For reciprocating engines, ratings and operating limitations are established relating to the following: (1) Horsepower or torque, r.p.m., manifold pressure, and time at critical pressure altitude and sea level pressure altitude for--
(i) Rated maximum continuous power (relating to unsupercharged operation or to operation in each supercharger mode as applicable); and (ii) Rated takeoff power (relating to unsupercharged operation or to operation in each supercharger mode as applicable).
(2) Fuel grade or specification. (3) Oil grade or specification. (4) Temperature of the-- (i) Cylinder; (ii) Oil at the oil inlet; and (iii) Turbosupercharger turbine wheel inlet gas. (5) Pressure of-- (i) Fuel at the fuel inlet; and (ii) Oil at the main oil gallery. (6) Accessory drive torque and overhang moment. (7) Component life. (8) Turbosupercharger turbine wheel r.p.m. (c) For turbine engines, ratings and operating limitations are established relating to the following: (1) Horsepower, torque, or thrust, r.p.m., gas temperature, and time for-- (i) Rated maximum continuous power or thrust (augmented);
(ii) Rated maximum continuous power or thrust (unaugmented);
(iii) Rated takeoff power or thrust (augmented); (iv) Rated takeoff power or thrust (unaugmented); (v) Rated 30 Minute OEI power; (vi) Rated 2-l/2 Minute OEI power; (vii) Rated Continuous OEI power; and (viii) Auxiliary power unit (APU) mode of operation. (2) Fuel designation or specification. (3) Oil grade or specification. (4) Hydraulic fluid specification. (5) Temperature of-- (i) Oil at a location specified by the applicant; (ii) Induction air at the inlet face of a supersonic engine, including steady state operation and transient over-temperature and time allowed; (iii) Hydraulic fluid of a supersonic engine; (iv) Fuel at a location specified by the applicant; and
(v) External surfaces of the engine; if specified by the applicant.
(6) Pressure of-- (i) Fuel at the fuel inlet; (ii) Oil at a location specified by the applicant; (iii) Induction air at the inlet face of a supersonic engine, including steady state operation and transient overpressure and time allowed; and (iv) Hydraulic fluid.
(7) Accessory drive torque and overhang moment. (8) Component life. (9) Fuel filtration. (10) Oil filtration. (11) Bleed air.
(12) The number of start-stop stress cycles approved for each rotor disc and spacer. (13) Inlet air distortion at the engine inlet. (14) Transient rotor shaft overspeed r.p.m., and number of overspeed occurrences. (15) Transient gas overtemperature, and number of overtemperature occurrences. (16) For engines to be used in supersonic aircraft engine rotor windmilling rotational r.p.m.
***
Guidance: The INTENT of this section is to publicly document the engine ratings and limitations data and other information necessary for safe operation of the engine.
Incorporations: AC 91-33A, "Use of Alternate Grades of Aviation Gasoline for Grade 80/87 and Use of Automotive Gasoline," dated July 1984.
References:
1. RTCA Document DO-160B.
2. SAE Committee Report No. AE4EL.
3. AC 21-6~, "Production Under Type Certificate Only", dated July 1, 1982.
4. AC 21-lB, "Production Certificate", dated May 10 1976.
a. Tests. Specific block tests are conducted to establish the various rated powers and thrusts, and the maximum and minimum operating limitations.
(1) The effects of altitude on engine ratings and operating limitations should be determined acceptably. This may be accomplished by means of altitude chamber testing, flight testing, simulated altitude testing, or analytical data using proven methodology.
(2) The ratings' limiting maximum operating parameters should be qualified by operation as indicated in the 150-hour FAA endurance test. Other limitations may be qualified by testing in which the limiting values may be the average attained for appropriate durations.
Special or additional tests may be necessary, at (3) times, to qualify some limitations for either complex engines, such as turbine engines with several r&or systems when limiting test conditions cannot be easily maintained for all rotors simultaneously, or where limits for components may be tested separately on rig tests. Specific examples are:
(i) Under certain ambient conditions, it may not be possible to simultaneously exercise to its respective speed limitation, each rotor of a multiple rotor engine during endurance test running. In such a case, and if approved by the cognizant FAA project manager or engineer, the test may be replicated as necessary to demonstrate each respective limitation, as also discussed under the "Section 33.87, Endurance Test" paragraph of this AC.
(ii) Engine electronic control devices such as full authority digital electronic controls (FADECs), require substantiation of tolerance to the effects of lightning strikes. This substantiation is interpreted to be necessary under the general requirements of FAR Section 33.91(a). Current practice is to require an installations simulation of the complete enginefurnished FADEC system, including cables and connectors, to be subjected to direct and induced lightning strike tests. This effort is typically conducted in accordance with the guidance information provided in References 1 and 2 above. The primary expected outcomes of this testing are definition of the lightning energy levels which the FADEC system can tolerate without adverse affects, and the level of shielding or other protection which the airframer will need to provide upon installation of the FADEC system in the aircraft.
(4) Military test data and reports may be used for certification purposes, if they are determined by the FAA type certification project manager or engineer to satisfy the criteria of the appropriate FAR Part 33 section, and of the conformity inspection requirements of Section 21.53.
b. Ratinqs and Limitations. Rated engine powers and thrusts are usually established on the basis of engine operation on a test stand, in its normal operating configuration; but usually with, at least, a test stand inlet in place of the aircraft installation hardware.
(1) Ratings are included on the engine TCDS.
(2) All operating limitations that may be considered by the applicant to affect flight safety, if exceeded, are to be noted in the model description and should include such items as the maximum values of: Engine pressure ratio (EPR); torque; rotorspeeds; powers; gas path temperatures; component temperatures; manifold pressure; vibration levels; fuel and
lubricant pressures and temperatures; time at ratings; and number of excursions at ratings.
C. Production and Overhauled Enqines. Although discussion of production engines would normally be considered beyond the scope of type certification, the following information may be useful:
(1) Each engine newly produced under a type certificate P-C) only, or under a production certificate, must be tested to assure that engine output is not less than the TC ratings and within each rating's respective associated operating limitations. (See References 3 and 4 above).
(2) It should be recognized that engine manufacturers and overhaulers will typically deliver engines with some degree of performance margin. This margin is usually based on a business agreement between the engine supplier and the installer or user.
(i) The important point is that there is no regulatory basis for engines to have more than minimum type certificated (specification) power/thrust available at delivery, whether in new or overhauled condition.
(ii) A further point is that in-service engines must always be capable of delivering the type certificate rating minimum performance, again, within the respective rating's operating limitations. Otherwise, the engine must be removed from further service and minimum performance restored before return to service.
(3) There are special cases wherein some in-service engine applications have been approved for subsequent operations to lesser performance levels than established during initial type certification. These cases are known as having deteriorated power operation approvals. Such cases have been approved only following extensive reevaluation of the engine and the aircraft to the deteriorated performance level, against the original type certification basis. This approval is limited to the specific initial operator's route structure.
19. Section 33.8, Selection of Enqine Power and Thrust Ratinqs.
Section 33.8 Selection of engine power and thrust ratings.
(a) Requested engine power and thrust ratings must be selected by applicant. (b) Each selected rating must be for the lowest power or thrust that all engines of the same type may be expected to produce under the conditions used to determine that rating.
***
- Guidance. The INTENT of this section is self-evident.
Incorporations: None.
References: None.
The objective of this requirement is to establish, on a uniform basis, the power or thrust ratings which new engines, and engines restored to new condition, are required to produce. These ratings are used in establishing aircraft performance for which consistent minimum performance is desired. Ratings selected by the applicant are established by FAA block tests. Ratings are typically based on specific atmospheric conditions, for the static case, with no customer bleed, no power extraction, and 100 percent recovery of inlet and exhaust losses. The applicant's experience on the calibrated output of a number of engines, of both the applicable new model and of engines of closely similar design characteristics, should be reviewed to evaluate the range of output expected in all other engines of that type. The selected ratings should be consistent with the output of the lowest output engine anticipated.
Chap 3
35 (and 36) par 19
.-
SECTION 2. SUBPART B--DESIGN AND CONSTRUCTION; GENERAL
SECTION 2. SUBPART B--DESIGN AND CONSTRUCTION; GENERAL
20. Section 33.14, Start-Stop Cvclic Stress (Low-Cycle Fatique).
Section 33.14 Start-stop cyclic stress (low-cycle fatigue).
By a procedure approved by the FAA, operating limitations must be established which specify the maximum allowable number of start-stop stress cycles for each rotor structural part (such as discs, spacers, hubs, and shafts of the compressors and turbines), the failure of which could produce a hazard to the aircraft. A startstop stress cycle consists of a flight cycle profile or an equivalent representation of engine usage. It includes starting the engine, accelerating to maximum rated power or thrust, decelerating, and stopping. For each cycle, the rotor structural parts must reach stabilized temperature during engine operation at maximum rated power or thrust and after engine shutdown, unless it is shown that the parts undergo the same stress range without temperature stabilization.
***
Guidance. The INTENT of this section is to establish cyclic life limits using FAA-approved methodology for rotating structural components whose failure could produce a hazard to the aircraft.
Incorporations: AC 33.3, "Turbine and Compressor Rotors Type Certification Substantiation Procedures," dated September 9, 1968.
References: None.
The guidance embodied in the "Incorporations" above, with respect to determination of service life limits, is still considered valid.
a. Some applicants have pre-approved procedures on file with the FAA for establishing initial (and increases of) low cycle fatigue (LCF) lives. Such procedures should be utilized where they exist.
b. The FAA requires the applicant to define the LCF verification test cycle, based on the most severe mission cycle expected in service. The determination of the most severe mission cycle expected in service is based on the concurrence of the FAA engine certification project manager with the applicant's proposed definition.
(1) It is determined logically, based on the type of engine, types of airframe applications, and anticipated service
usage. In rare cases, specific airframe applications during the - time of the engine certification program are not known, and, therefore, more speculative, but conservative, approaches may need to be used. In all cases, the FAA's installation office may be consulted to assist in determining the mission cycle.
(2) The test cycle basis should, in part, incorporate some excursions to the redline limits of gas path temperature, rotational speeds, torques, pressures, etc., associated with the maximum ratings used in the mission cycle. Consider such excursions that could reasonably be expected to occur within the extremes of ambient temperature and takeoff altitude conditions encountered during the engine's service life.
(3) The supporting data required for LCF qualification includes mechanical and thermal stress analyses and tests, and material analyses and tests. Since there are various acceptable methods of determining maximum temperature gradients, the FAA does not advocate that any particular methodology be applied for thermal analyses. Test engine rotor structural parts should attain a stabilized temperature for each applied test cycle.
C. Increases in service life limits, similar to the determination of initial life limits, will need to be based on a representative severe operating cycle, identified from service experience. Programs to increase service life limits should be based on further cyclic testing and analysis of in-service parts that have attained a reasonable percentage of their life limits.
d. FAA findings of compliance with existing FAR Section 33.14 are based, in part, on the applicant's definition of the flight cycle profile, or equivalent representation of engine usage. Implementation of this aspect of the rule, in the case of OEI rated engines, requires addressing the use of OEI ratings at a realistic frequency representative of actual (expected) inservice use.
(1) To date, the service experience with OEI rated engines is that use of OEI ratings, following a true case of one engine having failed, is an extremely rare event. Thus, it is considered totally unrealistic to mandate the use of OEI ratings as a constituent of each flight cycle.
(2) However, the applicant is still required, in all cases, to account for low cycle fatigue effects, based on the anticipated usage of OEI ratings during the life of the engine. This could be accomplished, for example, by adding a reasoned finite number of cycles to the expended life of the appropriate components for each OEI power excursion.
21. Section 33.15, Materials.
Section 33.15 Materials.
The suitability and durability of materials used in the engine must-- (a) Be established on the basis of experience or tests; and
Conform to approved specifications (such as (b) industry or military specifications) that ensure their having the strength and other properties assumed in the design data.
*Jr*
Guidance. The INTENT of this section is self-evident.
Incorporations: AC 33-4, "Design Considerations Concerning the Use of Titanium in Aircraft Turbine Engines," dated July 28, 1983.
References: None.
The applicant should select approved specification materials in the design and construction of the engine to minimize the development of an unsafe condition of the engine. Although the regulations do not specifically address corrosion and deterioration, these factors need to be considered in the type certification process, particularly in the design stage. Examples are proposed use of non-corrosion resistant alloys in corrosionsusceptible areas and proposed use of galvanic materials in contact.
22. Section 33.17, Fire Prevention.
Section 33.17 Fire prevention.
(a) The design and construction of the engine and the materials used must minimize the probability of the occurrence and spread of fire. In addition, the design and construction of turbine engines must minimize the probability of the occurrence of an internal fire that could result in structural failure, overheating, or other hazardous conditions. (b) Except as provided in paragraphs (c), (d), and (e) of this section, each external line, fitting, and other component, which contains or conveys flammable fluid must be fire resistant. Components must be shielded or located to safeguard against the ignition of leaking flammable fluid. (c) Flammable fluid tanks and supports which are part of and attached to the engine must be fireproof or be enclosed by a fireproof shield unless damage by fire to
any non-fireproof part will not cause leakage or spillage of flammable fluid. For a reciprocating engine having an integral oil sump of less than 25-quart capacity, the oil sump need not be fireproof nor be enclosed by a fireproof shield.
(d) For turbine engines type certificated for use in supersonic aircraft, each external component which conveys or contains flammable fluid must be fireproof. (e) Unwanted accumulation of flammable fluid and vapor must be prevented by draining and venting.
***
Guidance. The INTENT of this section is to assure that design, materials, and construction techniques are used to minimize the occurrence and spread of fire.
Incorporations: AC 33-4, "Design Considerations Concerning the Use of Titanium in Aircraft Turbine Engines", dated July 28, 1983.
References:
1. SAE AS1055B, "Fire Testing of Flexible Hose, Tube Assemblies, Coils, Fittings, and Similar System Components," March 1, 1978.
2. SAE AIR 1377A, "Fire Test Equipment for Flexible Hose and Tube Assemblies," January 1980.
3. FAA Powerplant Engineering Report No. 3A, "Standard Fire Test Apparatus and Procedure," Revised March 1978.
4. FAA Report No. FAA-RD-79-51, "Titanium Combustion in Turbine Engines," dated July 1979; and JAR-E, Section 2, Paragraph ACJE53O(c), "Titanium Fires."
5. SAE Report No. 690436, "Ignition of Aircraft Fluids on High Temperature Engine Surfaces," by W.T. Westfield of the FAA.
6. FAA Report No. FAA-RD-75-155, "Ignition and Propagation Rates for Flames in a Fuel Mist," October 1975, by C.E. Polymeropoulos.
7. AC 20-135, "Powerplant Installation and Propulsion System Component Fire Protection Test Methods, Standards and Criteria," dated February 6, 1990.
a. The FAR Part 1 definitions of "fire resistant" and "fire proof" are very broad and are not quantified in terms of flame temperature and time of immersion. For purposes of engine certification, fire resistant should be associated with a test flame temperature of 2000 OF, for at least a 5-minute duration;
fireproof should be associated with a test flame temperature of - 2000 OF, for at least a 15-minute duration.
b. Fire test conditions to be applied should be established consistent with the intended use of the engine component or subsystem being evaluated. Examples of this are: sheet stock designed to be firewalls or fireshrouds; formed parts designed as oil tanks; castings designed as fuel pump bodies; seamless tubing designed as fuel and oil supply lines; etc.
C. The test flame should be applied at the component or subsystem location that is determined by analysis and/or inspection to be most critical to fire susceptibility. Additionally, the operating characteristics of the component or subsystem should be established consistent with those which would normally be expected to exist during actual engine fire conditions.
d. Fire susceptibility means not only the probable location of a fire, but also the specific location of the component or subsystem within the fire zone that may be least likely to survive the effects of a fire. Such a determination should consider, at least, the following potential factors: materials characteristics; parts geometry; local torching effects; joint seals; vibration characteristics; internal fluid levels, pressures, and flows; wicking of surface coatings; engine design requirement for installed engine, through nacelle exhaust ejector driven component cooling airflows; characteristics of probable leakage in forms of sprays, drops, streams; etc.
e. The fire test burner to be used should provide the desired 2000 OF flame temperature of sufficient size, and at an energy level (BTU/hr) appropriate to the geometry of the engine component or subsystem being evaluated. Further general guidance on burner configuration can be found in References 1, 2, and 3 above.
f. In all cases, fire test acceptance criteria should show no support of combustion by the constituent material being tested; no burn-through; no leakage of fluid-carrying or fluid-holding parts sufficient to increase the fire hazard; and fire-protecting parts should be capable of satisfactorily performing the functions for which they were designed.
g- Compliance with the requirements of Section 33.17(a) requires that the design and construction of turbine engines must minimize the probability of the occurrence of an internal fire that could result in structural failure, overheating, or other hazardous conditions. (See also Reference 4 above).
Available references relating to hot surface ignition - (HSIFOcriteria for fuels are consistent in that the HSI temperature for JP-type fuels is in the range of 425-500 OF (minimum) for the non-ventilated case. HSI temperature increases dramatically with increasing airflow. It is also influenced by the characteristics of the secondary cooling air and engine surface geometry, ventilation rates of the engine nacelle, direction and changes of direction of the cooling air, and changes in engine power while leakage is occurring. Further information on this topic is available in References 5 and 6 above.
23. Section 33.19, Durability.
Section 33.19 Durability.
(a) Engine design and construction must minimize the development of an unsafe condition of the engine between overhaul periods. The design of the compressor and turbine rotor cases must provide for the containment of damage from rotor blade failure. Energy levels and trajectories of fragments resulting from rotor blade failure that lie outside the compressor and turbine rotor cases must be defined. (b) Each component of the propeller blade pitch control system which is a part of the engine type design must meet the requirements of Section 35.42 of this chapter.
***
Guidance. The INTENT of this section is self-evident
Incorporations:
1. AC 33-4, "Design Considerations Concerning the Use of Titanium in Aircraft Turbine Engines," dated July 28, 1983.
2. AC 33-5, "Turbine Engine Rotor Blade Containment/Durability," dated June 18, 1990.
References: None.
a. This section addresses the generic safety requirement of engines between "overhaul" periods, in addition to specific design requirements for rotor blade containment and for propeller blade pitch control.
(1) The generic requirement is fulfilled by compliance not only to each of the appropriate sections of FAR Part 33, but also to the "grandfather" Sections of 21.33, "Inspection and tests," and 21.16, "Special conditions."
Chap 3 42 Par22
(2) Collectively, these speak to not only the basis for type certification, but more specifically to: (1) materials and products specifications; (2) conformance of parts to the drawings in the type design; (3) specification of manufacturing processes; and (4) construction and assembly specifications in the engine type design (drawings). Each of these items should be traceable in the type certification design documentation from the engine top assembly drawing.
b. This section also addresses the specific design requirements for rotor blade containment, whereas FAR Section 33.94 addresses the demonstration requirements; both are addressed in Incorporation 2. Essentially, the design (analysis) is borne out by testing to substantiate that the potential energy of the containment structure is greater than the kinetic energy of the released rotor blade debris.
24. Section 33.21, Enqine Coolinq.
Section 33.21 Engine cooling.
Engine design and construction must provide the necessary cooling under conditions in which the airplane is expected to operate.
***
Guidance. The INTENT of this section is self-evident.
Incorporations: None.
References: None.
Interpretations of this regulation have historically been limited to operating fluid, external engine surface, and component heat rejection considerations, particularly of reciprocating engines. However, inasmuch as the rule applies to "Design and Construction-General," it should be interpreted to apply to both reciprocating and turbine engines, and to all engine cooling considerations.
b. Evaluation of the engine cooling systems design should not only address operating fluid and external component cooling, but also internal flow path cooling of turbochargers, rotors, spacers, nozzles, combustors, cases, etc. Particular attention should be given to ensure that continued safe operation and integrity of the critical structural components, while operating in the intended environment, is maintained throughout the design life and/or time to inspection, as appropriate.
25. Section 33.23, Engine Mounting Attachments and Structure.
Section 33.23 Engine mounting attachments and structure.
(a) The maximum allowable limit and ultimate loads for engine mounting attachments and related engine structure must be specified. (b) The engine mounting attachments and related engine structure must be able to withstand-- (1) The specified limit loads without permanent deformation; and (2) The specified ultimate loads without failure, but may exhibit permanent deformation.
***
Guidance. The INTENT of this section is to specify the allowable limit and ultimate loads, as defined, for the engine mounting attachments and related engine structure.
Incorporations: None.
References: None.
a. Engine attachment (mount) limit loads are the maximum loads to be expected in service and include, in combination, static mount loads, operating engine maximum reactive torque loads, gyroscopic loads, and maximum ground and flight loads. Ultimate load capability of the engine attachment mount structure is substantiated by analysis and by limited rig and component testing, which should also serve to validate the applicant's analytical methodology.
b. Engine mounting attachments and structure design should include consideration of deterioration, and corrosion effects expected during the design life of the engine. Suitable methods of detection of pending faults and failures at, or between, inspection intervals to be approved, should also be given consideration.
26. Section 33.25, Accessory Attachments.
Section 33.25 Accessory attachments.
The engine must operate properly with the accessory drive and mounting attachments loaded. Each engine accessory drive and mounting attachment must include provisions for sealing to prevent contamination of, or unacceptable leakage from, the engine interior. A drive and mounting attachment requiring lubrication for external drive splines, or coupling by engine oil, must include provisions for sealing to prevent unacceptable loss of oil
and to prevent contamination from sources outside the - chamber enclosing the drive connection. The design of the engine must allow for the examination, adjustment, or removal of each accessory required for engine operation.
***
Guidance. The INTENT of this section is that design and construction of engine accessory drives and their mount pads permit proper engine operation when loaded; prevent contamination and excessive loss of oil; and permit inspection, adjustment, and removal of accessories.
Incorporations: None.
References: None.
If engine accessory drives are designed to protect the engine from potential unsafe conditions, such as those due to accessory seizure overtorque, by designed failure of a drive shaft shear section; then, it should be shown that the shear section will not fail under all normal operating load conditions, or otherwise result in damage or hazard to the engine or its subsequent aircraft installation.
27. Section 33.27, Turbine, Compressor, Fan and Turbosupercharser Rotors.
Section 33.27 Turbine, compressor, fan and turbosupercharger rotors.
(a) Turbine, compressor, fan, and turbosupercharger rotors must have sufficient strength to withstand the test conditions specified in paragraph (c) of this section. (b) The design and functioning of engine control devices, systems, and instruments must give reasonable assurance that those engine operating limitations that affect turbine, compressor, and turbosupercharger rotor structural integrity will not be exceeded in service. (c) The most critically stressed rotor component (except blades) of each turbine, compressor, and fan, including integral drum rotors and centrifugal compressors in an engine or turbosupercharger, as determined by analysis or other acceptable means, must be tested for a period of 5 minutes-- (1) At its maximum operating temperature, except as provided in paragraph (c)(2)(iv) of this section; and (2) At the highest speed of the following, as applicable:
120 percent of its maximum permissible r.p.m. if (i) tested on a rig and equipped with blades or blade weights.
(ii) 115 percent of its maximum permissible r.p.m. if tested on an engine. (iii) 115 percent of its maximum permissible r.p.m. if tested on a turbosupercharger driven by a hot gas supply from a special burner rig. (iv) 120 percent of the r.p.m. at which, while cold spinning, it is subject to operating stresses that are equivalent to those induced at the maximum operating temperature and maximum permissible r.p.m. (VI 105 percent of the highest speed that would result from failure of the most critical component or system in a representative installation of the engine. (vi) The highest speed that would result from the failure of any component or system in a representative installation of the engine, in combination with any failure of a component or system that would not normally be detected during a routine preflight check or during normal flight operation. Following the test, each rotor must be within approved dimensional limits for an overspeed condition and may not be cracked.
***
Guidance. The INTENT of this section is to assure engine rotor structural integrity, by design and functioning of engine control and instrumentation systems, to inhibit exceedances of operating limitations; and, to demonstrate that each engine rotor has sufficient strength to withstand a maximum overspeed condition without cracking.
Incorporations: None.
References: None.
a. If the engine bill-of-material includes instrumentation (including sensors), then such must be designed and must function so as to assure safe operation, (structural integrity of the inservice engine). Note that the rule requires the most critically stressed rotor component (including discs, spacers, cooling plates) of each turbine, compressor, and fan to be tested at a maximum overspeed condition for 5 minutes. Determination of the maximum overspeed condition needs to consider the 6 cases defined in the rule -- including shaft failures which decouple a turbine rotor from its load. Rotor shafts are not considered "prime reliable" in that it is assumed that shaft failures will occur, both as a single failure and in combination with another undetected or dormant failure.
b. A rotor burst test, in lieu of the presently required 5minute overspeed test, could be found as an acceptable equivalent means of compliance. In the case of output shaft (low) turbines,
- the rotor burst test would be performed, in conjunction with an abrupt load decouple test, to demonstrate the existence of adequate margin between the peak speed and the burst speed. The actual burst speed must be corrected to account for the effects of gas path temperature (i.e., actual engine at maximum operating temperature versus spin pit temperature at burst), and test specimen actual material properties versus specification minimum material properties. Acceptance criteria must show at least a 5.0 percent speed margin between the abrupt decouple peak speed and the corrected burst speed.
C. The following table, provided as a historical reference, correlates the rotor integrity regulation and its guidance, including significant differences:
-
TABLE 27-l. ROTOR INTEGRITY REGULATIONS/GUIDANCE
TABLE 27-l. ROTOR INTEGRITY REGULATIONS/GUIDANCE
REGULATION & CORRESPONDING SIGNIFICANT GUIDANCE EFFECTIVITY DATE GUIDANCE & DIFFERENCES ISSUE DATE
FAR 33-13, 08/18/89 AC 33-3, o POST-TEST ACCEPTANCE FAR 33-12, 10/03/88 09/09/68 CRITERIA OF THE FAR TAKES FAR 33-11, 04/24/86 PRECEDENCE OVER THAT OF FAR 33-10, 03/26/84 THE AC. FAR 33-9, 10/14/80 FAR 33-8, 05/02/77 FAR 33-7, 02/01/77 FAR 33-6, 10/31/74
REGULATION & CORRESPONDING SIGNIFICANT GUIDANCE EFFECTIVITY DATE GUIDANCE & DIFFERENCES ISSUE DATE
FAR 33-5, 03/01/74 AC 33-3, o FAR DOES NOT FAR 33-4, 04/23/71 09/09/68 IDENTIFY POST-TEST ACCEPTANCE CRITERIA.
FAR 33-3, 04/03/67 AC 20-26, o POST-TEST ACCEPTANCE FAR 33-2, 07/06/66 CH.2 CRITERIA OF THE AC 07/08/65 REVISED BY CH.2. (PARAGRAPH 4C).
FAR 33 & AC 20-26 o SUPERSEDES FAA 33-1, 02/01/65 CH.l, 09/18/64; MEMORANDUM OF 02/09/59. AC 20-26, o OVERSPEED TEST 07/22/64 CONDITION ANALYSIS BASED ON FAILURE(S).
CAR 13-6, 04/22/64 FAA POLICY o ESTABLISHES CAR 13-5; 02/12/63 MEMORANDUM, REQUIREMENTS FOR CAR 13-4, 05/03/62 02/09/59 SUBSTANTIATION OF TURBINE CAR 13-3, 10/01/59 & COMPRESSOR ROTOR INTEGRITY. NOTE THAT THE OVERSPEED TEST CONDITION TO BE RUN IS BASED ON ANALYSIS OF CONTROL SYSTEM FAILURE(S) AND ON A FACTOR OF TAKEOFF
R.P.M., WHICHEVER YIELDS THE GREATEST STRESS. o MUST DEMONSTRATE OVERSTRESS MARGIN, BUT DOES NOT OFFER ACCEPTANCE CRITERIA.
CAR 13-2, 05/17/58 NONE N/A CAR 13-1, 08/12/57
CAR 13-2, 05/17/58 NONE N/A CAR 13-1, 08/12/57
28. Section 33.29, Instrument Connection. -
Section 33.29 Instrument connection.
(a) Unless it is constructed to prevent its connection to an incorrect instrument, each connection provided for powerplant instruments required by aircraft airworthiness regulations or necessary to insure operation of the engine in compliance with any engine limitation must be marked to identify it with its corresponding instrument.
(b) A connection must be provided on each turbojet engine for an indicator system to indicate rotor system unbalance.
***
Guidance. The INTENT of this section is to prevent misconnections of engine-required instrumentation, and to provide a drawing location for rotor unbalance sensing.
Incorporations: None.
References: None.
An acceptable method of complying with FAR Section 33.29(b) is to identify, on the engine installation drawing, the flange location for installation of the unbalance indicator transducer. Historically, "turbojet" has been interpreted to also include fan engines.
Chap 3 Par 28 49 (and 50)
SECTION 3. SUBPART C --DESIGN AND CONSTRUCTION; RECIPROCATING AIRCRAFT ENGINES
SECTION 3. SUBPART C --DESIGN AND CONSTRUCTION; RECIPROCATING AIRCRAFT ENGINES
29. Section 33.33, Vibration.
Section 33.33 Vibration.
The engine must be designed and constructed to function throughout its normal operating range of crankshaft rotational speeds and engine powers without inducing excessive stress in any of the engine parts because of vibration and without imparting excessive vibration forces to the aircraft structure.
***
Guidance. The INTENT of this section is self-evident.
Incorporations: None.
References: None.
30. Section 33.35, Fuel and Induction System.
Section 33.35 Fuel and induction system.
(a) The fuel system of the engine must be designed and constructed to supply an appropriate mixture of fuel to the cylinders throughout the complete operating range of the engine under all flight and atmospheric conditions. (b) The intake passages of the engine through which air or fuel in combination with air passes for combustion purposes must be designed and constructed to minimize the danger of ice accretion in those passages. The engine must be designed and constructed to permit the use of a means for ice prevention. (c) The type and degree of fuel filtering necessary for protection of the engine fuel system against foreign particles in the fuel must be specified. The applicant must show that foreign particles passing through the prescribed filtering means will not critically impair engine fuel system functioning. (d) Each passage in the induction system that conducts a mixture of fuel and air must be self-draining, to prevent a liquid lock in the cylinders, in all attitudes that the applicant establishes as those the engine can have when the aircraft in which it is installed is in the static ground attitude. (e) If provided as part of the engine, the applicant must show for each fluid injection (other than fuel) system and its controls that the flow of the injected fluid is adequately controlled.
Guidance. The INTENT of this section is self-evident.
Incorporations: None.
References: None.
31. Section 33.37, Iqnition System.
Section 33.37 Ignition system.
Each spark ignition engine must have a dual ignition system with at least two spark plugs for each cylinder and two separate electric circuits with separate sources of electrical energy, or have an ignition system of equivalent in-flight reliability.
***
Guidance. The INTENT of this section is self-evident.
Incorporations: None.
References: None.
The engine installation instructions should define the characteristics and interface requirements of all aircraft sources of electrical power required by the engine ignition system.
32. Section 33.39, Lubrication System.
Section 33.39 Lubrication system.
(a) The lubrication system of the engine must be designed and constructed so that it will function properly in all flight attitudes and atmospheric conditions in which the airplane is expected to operate. In wet sump engines, this requirement must be met when only one-half of the maximum lubricant supply is in the engine. (b) The lubrication system of the engine must be designed and constructed to allow installing a means of cooling the lubricant. (c) The crankcase must be vented to the atmosphere to preclude leakage of oil from excessive pressure in the crankcase.
***
Guidance. The INTENT of this section is self-evident.
Incorporations: None.
References: None.
SECTION 4. SUBPART D--BLOCK TESTS; RECIPROCATING AIRCRAFT ENGINES -
SECTION 4. SUBPART D--BLOCK TESTS; RECIPROCATING AIRCRAFT ENGINES -
33. Section 33.42, General.
Section 33.42 General.
Before each endurance test required by this subpart, the adjustment setting and functioning characteristic of each component having an adjustment setting and a functioning characteristic that can be established independent of installation on the engine must be established and recorded.
***
Guidance. The INTENT of this section is self-evident.
Incorporations: None.
References: None.
34. Section 33.43, Vibration Test.
Section 33.43 Vibration test.
(a) Each engine must undergo a vibration survey to establish the torsional and bending vibration characteristics of the crankshaft and the propeller shaft or other output shaft, over the range of crankshaft speed and engine power, under steady state and transient conditions, from idling speed to either 110 percent of the desired maximum continuous speed rating or 103 percent of the maximum desired takeoff speed rating, whichever is higher. The survey must be conducted using, for airplane engines, the same configuration of the propeller type which is used for the endurance test, and using, for other engines, the same configuration of the loading device type which is used for the endurance test. (b) The torsional and bending vibration stresses of the crankshaft and the propeller shaft or other output shaft may not exceed the endurance limit stress of the material from which the shaft is made. If the maximum stress in the shaft cannot be shown to be below the endurance limit by measurement, the vibration frequency and amplitude must be measured. The peak amplitude must be shown to produce a stress below the endurance limit; if not, the engine must be run at the condition producing the peak amplitude until, for steel shafts, 10 million stress reversals have been sustained without fatigue failure and, for other shafts, until it is shown that fatigue will not occur within the endurance limit stress of the material.
Continue reading ↓ 120 of 260 passages shown