Radar Vectors
Advisory Circular Cancelled Issued Mar 29, 2011 ANM-110 410 pages Copy saved Nov 18, 2026

AC 25-7B Flight Test Guide for Certification of Transport Category Airplanes

This advisory circular (AC) provides guidance for the flight test evaluation of transport category airplanes. This AC includes flight test methods and procedures to show compliance with the regulations contained in subpart B of Title 14, Code of Federal Regulations (14 CFR) part 25, which address airplane performance and handling characteristics. Part 25 has been amended significantly since the last revision of this AC and, likewise, guidance and policy have changed in many areas as experience has been gained. During this time period, technology has advanced as well, resulting in a need for new or modified test techniques. This revision, AC 25-7B, adds acceptable means of compliance for the regulatory changes associated with amendments 108, 109, and 115 to part 25, and a revised means of compliance for expansion of takeoff and landing data for higher airport elevations. Means of compliance associated with flight in icing conditions was removed as this material is now contained in AC 25-25.

This document is cancelled. It may have been replaced. Check the official source before relying on it.

Official source ↗ Open PDF

1. Purpose. This Change provides updated guidance material to ensure consistent application of certain airworthiness requirements adopted by Amendment 25-135 to 14 CFR part 25. Changed material is indicated by bold lines in the margins and at the top of each changed page with the change number and date. Some text, although not changed, has been rearranged to accommodate new material. 2. Principal Changes. a. Revised guidance regarding an acceptable means of compliance for VMU testing for geometry-limited airplanes to show compliance with § 25.107(e)(1)(iv). b. Revised guidance regarding an acceptable means of compliance for showing compliance with the static directional and lateral stability requirements of § 25.177. c. New guidance regarding an acceptable means of compliance for showing compliance with the roll capability requirements of § 25.253(a)(4). d. New guidance regarding an acceptable means of compliance for showing compliance with the speedbrake extension requirements of § 25.253(a)(5).

Page Control Chart Remove Pages Dated Insert Pages Dated Front Page 3/29/2011 Front page for 25-7B Change 1 12/7/11 i - xii 3/29/2011 i-xii 12/7/11 1-2 3/29/2011 1-2 12/7/11 24-293 3/29/2011 24-297 12/7/11 A1-5 – A1-7 3/29/2011 A1-5 – A1-7 12/7/11

Subject: Flight Test Guide For Certification of Transport Category Airplanes

Date: 12/07/11 Initiated By: ANM-110

AC No: 25-7B Change: 1

Ali Bahrami Manager, Transport Airplane Directorate Aircraft Certification Service

12/07/11 AC 25-7B Change 1

i

Table of Contents Paragraph Page No.

1. Purpose. … i

2. Principal Changes … i

2. Principal Changes … i

Introduction … 1

1. Purpose … 1

2. Applicability … 1

4. Background … 1

5. Related Publications … 2

Chapter 1 - General … 3

1. Applicability - § 25.1 [Reserved] … 3

2. Special Retroactive Requirements - § 25.2 [Reserved] … 3

Chapter 2 - Flight … 4

Section 1. General … 4

Section 1. General … 4

3. Proof of Compliance - § 25.21 … 4

4. Load Distribution Limits - § 25.23 [Reserved] … 16

5. Weight Limits and Center of Gravity Limits - §§ 25.25 and 25.27 … 16

[Reserved] … 16

6. Empty Weight and Corresponding Center of Gravity - § 25.29 … 16

[Reserved] … 16

7. Removable Ballast - § 25.31 [Reserved] … 16

8. Propeller Speed and Pitch Limits - § 25.33 … 16

Section 2. Performance … 17

Section 2. Performance … 17

9. General - § 25.101 … 17

10. Takeoff and Takeoff Speeds - §§ 25.105 and 25.107 … 19

11. Accelerate-Stop Distance - § 25.109 … 28

12. Takeoff Path - § 25.111 … 55

12/07/11 AC 25-7B Change 1

ii

Table of Contents (continued) Paragraph Page No.

13. Takeoff Distance and Takeoff Run - § 25.113 … 63

14. Takeoff Flight Path - § 25.115 … 67

15. Climb: General - § 25.117 … 69

16. Landing Climb: All-Engines-Operating - § 25.119 … 69

17. Climb: One-Engine-Inoperative - § 25.121 … 70

18. En Route Flight Paths - § 25.123 … 72

19. Landing - § 25.125 … 73

Section 3. Controllability and Maneuverability … 81

Section 3. Controllability and Maneuverability … 81

20. General - § 25.143 … 81

21. Longitudinal Control - § 25.145 … 94

22. Directional and Lateral Control - § 25.147 … 99

23. Minimum Control Speed - § 25.149 … 102

Section 4. Trim … 109

24. Trim - § 25.161 [Reserved] … 109

Section 5. Stability … 109

Section 5. Stability … 109

25. General - § 25.171. [Reserved] … 109

26. Static Longitudinal Stability and Demonstration of Static … 109

Longitudinal Stability - §§ 25.173 and 25.175 … 109

27. Static Directional and Lateral Stability - § 25.177 … 111

28. Dynamic Stability - § 25.181 … 116

Section 6. Stalls … 118

29. Stall Testing … 118

29. Stall Testing … 118

Section 7. Ground and Water Handling Characteristics … 134

30. General … 135

12/07/11 AC 25-7B Change 1

iii

Table of Contents (continued) Paragraph Page No.

Section 8. Miscellaneous Flight Requirements … 138

31. Vibration and Buffeting - § 25.251 … 138

32. High Speed Characteristics - § 25.253 … 143

Section 8. Miscellaneous Flight Requirements … 138

33. Out-of-Trim Characteristics - § 25.255 … 148

Chapter 3 - Structure … 152

Chapter 4 – Design and Construction … 153

Section 1. General [Reserved] … 153

Section 2. Control Surfaces [Reserved] … 153

Section 3. Control Systems … 153

34. General - § 25.671 … 153

35. - 45. [Reserved] … 153

Section 3. Control Systems … 153

46. Flap and Slat Interconnections - § 25.701 … 153

47. Takeoff Warning System - § 25.703. [Reserved] … 154

Section 4. Landing Gear … 154

48. - 51. [Reserved] … 154

52. Retracting Mechanism - § 25.729 … 154

53. Wheels - § 25.731 … 155

54. Tires - § 25.733 [Reserved] … 157

55. Brakes - § 25.735 … 157

Section 4. Landing Gear … 154

56. Skis - § 25.737 [Reserved] … 172

Section 5. Floats and Hulls … 172

57. - 59. [Reserved] … 172

Section 6. Personnel and Cargo Accommodations … 172

60. - 61. [Reserved] … 172

12/07/11 AC 25-7B Change 1

iv

Table of Contents (continued) Paragraph Page No.

62. Pilot Compartment View - § 25.773 … 173

Section 6. Personnel and Cargo Accommodations … 172

63. - 72. [Reserved] … 173

Section 7. Emergency Provisions … 173

73. Ditching - § 25.801 [Reserved] … 173

74. Emergency Egress Assist Means and Escape Routes - § 25.810 … 173

75. - 83. [Reserved] … 173

Section 8. Ventilation and Heating … 173

84. Ventilation - § 25.831 … 173

85. Cabin Ozone Concentration - § 25.832 [Reserved] … 174

Section 8. Ventilation and Heating … 173

86. Combustion Heating Systems - § 25.833 [Reserved] … 174

Section 9. Pressurization … 174

87. Pressurized Cabins - § 25.841 … 174

88. Tests For Pressurized Cabins - § 25.843 … 177

Section 10. Fire Protection [Reserved] … 178

Section 11. Miscellaneous [Reserved] … 178

Chapter 5 - Powerplant … 179

Section 1. General … 179

Section 1. General … 179

89. Installation - § 25.901. [Reserved] … 179

90. Engines - § 25.903 … 179

91. Automatic Takeoff Thrust Control System (ATTCS) - § 25.904 … 182

92. Propellers - § 25.905 … 184

93. Propeller Vibration and Fatigue - 25.907 [Reserved] … 184

94. Propeller Clearance - § 25.925 [Reserved] … 184

95. Propeller Deicing - § 25.929 … 185

96. Reversing Systems - § 25.933 … 185

12/07/11 AC 25-7B Change 1

v

Table of Contents (continued) Paragraph Page No.

97. Turbojet Engine Thrust Reverser System Tests - § 25.934. [Reserved] … 188

98. Turbopropeller-Drag Limiting Systems - § 25.937 … 188

99. Turbine Engine Operating Characteristics - § 25.939 … 190

100. Inlet, Engine, and Exhaust Compatibility - § 25.941. [Reserved] … 190

101. Negative Acceleration - § 25.943 … 190

102. Thrust or Power Augmentation System § 25.945. [Reserved] … 191

Section 2. Fuel System … 191

Section 2. Fuel System … 191

[103. - 108.] [Reserved] … 191

109. Unusable Fuel Supply - § 25.959 … 191

110. Fuel System Hot Weather Operation - § 25.961 … 193

[111. - 116.] [Reserved] … 195

117. Fuel Tank Vents and Carburetor Vapor Vents - § 25.975 … 195

[118. - 120.] [Reserved] … 197

Section 3. Fuel System Components … 197

Section 3. Fuel System Components … 197

[121. - 126.] [Reserved] … 197

127. Fuel Jettisoning System- § 25.1001 … 197

Section 4. Oil System [Reserved] … 200

Section 5. Cooling … 200

[128. - 130.] [Reserved] … 200

Section 6. Induction System … 200

131. Air Induction - § 25.1091 … 200

Section 6. Induction System … 200

132. Induction System Icing Protection - § 25.1093 … 202

[133. - 136.] [Reserved] … 204

Section 7. Exhaust System … 204

12/07/11 AC 25-7B Change 1

vi

Table of Contents (continued) Paragraph Page No.

137. General - § 25.1121 … 204

[138. - 140.] [Reserved] … 205

Section 8. Powerplant Controls and Accessories … 205

Section 8. Powerplant Controls and Accessories … 205

[141. - 154.] [Reserved] … 205

Section 9. Powerplant Fire Protection … 205

[155. - 158.] [Reserved] … 205

159. Drainage and Ventilation Of Fire Zones - § 25.1187 … 205

[160. - 164.] [Reserved] … 206

165. Fire Extinguishing Agents - § 25.1197 … 206

[166. - 169.] [Reserved] … 206

Chapter 6 - Equipment … 207

Section 1. General … 207

Section 1. General … 207

170. Equipment – Function and Installation - § 25.1301 … 207

171. Flight and Navigation Instruments - § 25.1303 … 240

172. Powerplant Instruments - § 25.1305. [Reserved] … 241

173. Miscellaneous Equipment - § 25.1307. [Reserved] … 241

174. Equipment, Systems, and Installations - § 25.1309 … 242

Section 2. Instruments: Installation … 242

Section 2. Instruments: Installation … 242

175. Arrangement and Visibility - § 25.1321. [Reserved] … 242

176. Warning, Caution, and Advisory Lights - § 25.1322. [Reserved] … 242

177. Airspeed Indicating System - § 25.1323 … 242

178. Static Pressure Systems - § 25.1325(d) and (e) … 246

179. Pitot Heat Indication Systems - § 25.1326. [Reserved] … 247

180. Magnetic Direction Indicator - § 25.1327. [Reserved] … 247

12/07/11 AC 25-7B Change 1

vii

Table of Contents (continued) Paragraph Page No.

181. Automatic Pilot System - § 25.1329 … 247

[182. - 185.] [Reserved] … 263

Section 3. Electrical Systems and Equipment … 264

Section 3. Electrical Systems and Equipment … 264

186. General - § 25.1351 … 264

187. Electrical Equipment and Installations - § 25.1353 … 266

188. Distribution System - § 25.1355 … 268

189. Circuit Protective Devices - § 25.1357. [Reserved] … 268

190. Electrical System Tests - § 25.1363 … 268

Section 4. Lights … 268

Section 4. Lights … 268

191. Instrument Lights - § 25.1381 … 268

192. Landing Lights - § 25.1383 … 269

193. Position Light System Installation - § 25.1385 … 269

[194. - 200.] [Reserved] … 269

201. Anti-Collision Light System - § 25.1401 … 269

202. Wing Icing Detection Lights - § 25.1403 … 270

Section 5. Safety Equipment … 270

Section 5. Safety Equipment … 270

[203. - 207.] [Reserved … 270

Section 6. Miscellaneous Equipment … 270

208. Electronic Equipment - § 25.1431 … 270

[209. - 223.] [Reserved] … 270

Chapter 7 – Operating Limitations and Information … 271

Section 1. General [Reserved] … 271

Section 2. Operating Limitations [Reserved] … 271

Section 3. Markings and Placards [Reserved] … 271

Section 3. Markings and Placards [Reserved] … 271

12/07/11 AC 25-7B Change 1

viii

Table of Contents (continued) Paragraph Page No.

Section 4. Airplane Flight Manual … 271

224. General - § 25.1581 … 271

[225. - 227.] [Reserved] … 271

Chapter 8 - Airworthiness: Miscellaneous Items … 272

Chapter 8 - Airworthiness: Miscellaneous Items … 272

228. Design and Function of Artificial Stall Warning and Identification Systems. __ 272

229. Reduced and Derated Thrust Takeoff Operations … 275

230. Runway Gradients Greater Than ± 2 Percent … 276

231. Criteria For Approval of Steep Approach To Landing … 277

232. Takeoff and Landing On Unpaved Runways … 281

233. Accountability of Performance Degradation Relative to Both Minor Design

Changes (External Posture) and Configuration Deviation List (CDL) Items … 284

234. Configuration Deviation List … 285

235. Spare Engine Pod … 287

236. Authorization For Ferry Flight With One Engine Inoperative - § 91.611 … 287

237. Instrument Landing System Weather Minima … 288

238. Takeoff Performance Credit For Alternate Forward Center of Gravity Limits. _ 289

239. Performance Credit For Automatic Propeller Drag Reduction Devices … 292

240. Airplane Backing Using Reverse Thrust … 293

12/07/11 AC 25-7B Change 1

ix

Table of Contents (continued)

Figures Figure Page No.

Figure 3-1. Weight Tolerance Limits … 6

Figure 3-2. Equivalent Weight Extrapolation … 7

Figure 3-3. Test Parameters That Normally Can Be Corrected … 9

Figure 3-4. Wind Profile Variation … 10

Figure 11-1. Accelerate-Stop Time Delays … 35

Figure 11-2. Accelerate-Stop Speed vs. Distance … 37

Figure 11-3. Anti-Skid System Response Characteristics … 41

Figure 11-4. Anti-Skid System Response Characteristics … 42

Figure 11-5. Anti-Skid System Response Characteristics … 44

Figure 11-6. Instantaneous Brake Force and Peak Brake Force … 47

Figure 11-7. Anti-Skid Efficiency – Wheel Slip Relationship … 49

Figure 11-8. Substantiation of the Optimal Slip Value … 51

Figure 13-1. Takeoff Distance on a Dry Runway … 63

Figure 13-2. Takeoff Distance … 64

Figure 13-3. Takeoff Distance On a Wet Runway … 65

Figure 13-4. Takeoff Run … 65

Figure 13-5. Takeoff Run … 66

Figure 13-6. Clearway Profiles … 67

Figure 14-1. Takeoff Segments & Nomenclature … 68

12/07/11 AC 25-7B Change 1

x

Table of Contents (continued) Figure Page No.

Figure 14-2. Net Takeoff Flight Path … 69

Figure 19-1. Landing Time Delays … 78

Figure 20-1. Sample Pitch Tracking Task … 89

Figure 20-2. A-PC Rating Criteria and Comparison To Mil Standard … 90

Figure 20-3 Example of Acceptable HQ Rating For A-PC Tendencies … 91

Figure 26-1. Longitudinal Static Stability … 111

Figure 29-1. Thrust Effect On Stall Speed … 123

Figure 29-2. CLMAX and Load Factor … 124

Figure 29-3. CLMAX vs Entry Rate … 126

Figure 29-4. CLMAX vs Weight and Flap Setting … 126

Figure 29-5. Stall Speed vs Weight and Flap Setting … 128

Figure 31-1. Maneuvering Characteristics … 142

Figure 31-2. Maneuvering Characteristics … 142

Figure 33-1. Mistrimmed Maneuvering Characteristics … 150

Figure 181-1 Altitude Loss versus Altitude Go-Around Mode … 255

12/07/11 AC 25-7B Change 1

xi

Table of Contents (continued)

Appendices

Appendix Page No.

Appendix 1 … A1-1

Appendix 1 … A1-1

Acronyms and Abbreviations … A1-1

Appendix 2 … A2-1

Function and Reliability Tests - § 21.35(b)(2) … A2-1

Appendix 3 … A3-1

Correction of Air Minimum Control Speed To Standard Conditions … A3-1

1. Theoretical Basis … A3-1

2. Constant Cn Method … A3-2

3. Graphical Method … A3-3

4. Equation Method … A3-7

4. Equation Method … A3-7

Appendix 4 … A4-1

History of Jet Transport Performance Standards … A4-1

Special Civil Air Regulation No. SR-422 … A4-2

Performance … A4-5

Airplane Flight Manual … A4-14

Operating Rules … A4-14

Special Civil Air Regulation No. SR-422A … A4-17

Performance … A4-25

Appendix 4 … A4-1

Airplane Flight Manual … A4-35

Operating Rules … A4-36

Special Civil Air Regulation No. SR-422B … A4-40

Performance … A4-43

Airplane Flight Manual … A4-54

12/07/11 AC 25-7B Change 1

xii

Table of Contents (continued)

Appendices

Appendix Page No.

Operating Rules … A4-55

Appendix 5 … A5-1

Appendix 5 … A5-1

Historical Development Of Accelerate-Stop Time Delays … A5-1

Figure 1. Accelerate-Stop Time Delays … A5-2

Figure 2. Accelerate-Stop Time Delays … A5-4

Appendix 6 … A6-1

FAA Handling Qualities Rating Method … A6-1

Figure 1. Airworthiness HQ Regulations Impacted/Outpaced by Technology … A6-2

Appendix 6 … A6-1

Figure 2. Probability vs. Consequence Graph … A6-3

Figure 3. Development of FAA HQRM Criteria … A6-4

Figure 4. Major Elements of Task-Oriented Handling Qualities Rating Method ___ A6-4

Figure 5. Probability Guidelines for Combined Occurrence Flight Conditions ____ A6-5

Figure 6. Flaps UP Flight Envelopes … A6-7

Figure 7. Flaps DOWN Flight Envelopes … A6-8

Figure 8. Pilot Ratings … A6-9

Figure 9. Probability Combination Leading to HQ Rating … A6-10

Figure 10. Probability Guidelines to Determine HQ Requirements … A6-11

Figure 11. General HQ Task Categories … A6-12

Figure 12. Minimum HQ Requirements … A6-13

Appendix 7 … A7-1

Appendix 7 … A7-1

Rudder Pedal Force-Limited Air Minimum Control Speed … A7-1

12/07/11 AC 25-7B Change 1

Introduction 1. Purpose. a. This Advisory Circular (AC ) provides updated guidance for the flight test evaluation of transport category airplanes. These guidelines provide an acceptable means of demonstrating compliance with the pertinent regulations of Title 14, Code of Federal Regulations (14 CFR) part 25. The methods and procedures described herein have evolved through many years of flight testing of transport category airplanes and, as such, represent current certification practice This AC is not mandatory and does not constitute a regulation. It describes acceptable means, but not the only means, for demonstrating compliance with the applicable regulation(s). The FAA will consider other methods of demonstrating compliance that an applicant may elect to present. If we become aware of circumstances that convince us that following this AC would not result in compliance with the applicable regulations, we will not be bound by the terms of this AC, and we may require additional substantiation or design changes as a basis for finding compliance.

This material does not change, create any additional, authorize changes in, or permit deviations from existing regulatory requirements. b. See Appendix 1 for a list of acronyms and abbreviations used in this AC. 2. Applicability. These methods and procedures are provided in the interest of certification approval for use during all transport category airplane flight test certification activities. This material is not to be construed as regulatory or having a mandatory effect. The procedures set forth herein are one acceptable means of compliance with applicable sections of part 25. Any alternative means proposed by the applicant should be given due consideration. Applicants are encouraged to use their technical ingenuity and resourcefulness in order to develop more efficient and less costly methods of complying with the requirements of part 25. Since these methods and procedures are only one acceptable means of compliance, individuals should be guided by the intent of the methods provided in this AC.

As deviations from the methods and procedures described in this AC may occur, FAA certification personnel will coordinate what they consider to be major deviations with the Transport Standards Staff (ANM-110) of the Transport Airplane Directorate. If in their judgment, however, a deviation is considered to be minor, coordination with ANM-110 may not be necessary. 3. Cancellation. AC-25-7B, “Flight Test Guide for Certification of Transport Category Airplanes, “dated March 29, 2011, is cancelled. 4. Background. Since AC 25-7 was released on April 9, 1986, it has been the primary source of guidance for flight test methods and procedures to show compliance with the regulations contained in subpart B of part 25, which address airplane performance and handling characteristics. AC 25-7 has been revised three times to reflect changes in the part 25 regulatory requirements, changes in guidance and policy, and advances in technology.

The first revision, AC 25-7A, updated the original AC to incorporate the policy and guidance material applicable to all sections of part 25, not just subpart B. The material related to regulations outside of subpart B superseded that contained in Order 8110.8, which was cancelled when AC 25-7A was issued. Change 1 to AC 25-7A added acceptable means of compliance for the regulatory changes

12/07/11 AC 25-7B Change 1

associated with amendments 92 and 98 to part 25. AC 25-7B added acceptable means of compliance for the regulatory changes associated with amendments 108, 109, and 115 to part 25, and revised guidance for expanding takeoff and landing data for airport elevations higher than those at which flight testing was conducted. Means of compliance associated with flight in icing conditions is removed as this material is now contained in AC 25-25. AC 25-7B Change 1 provides updated guidance material to ensure consistent application of airworthiness requirements adopted by Amendment 25-135 to 14 CFR part 25. 5. Related Publications. Certification personnel should be familiar with FAA Order 8110.4c, “Type Certification,” and FAA Order 8100.5A, “Aircraft Certification Service Mission, Responsibilities, Relationships, and Programs.” In this AC, reference is made to other FAA advisory circulars that provide guidance on various aspects of type certification and supplemental type certification.

Chapter 1 - General 1. Applicability - § 25.1 [Reserved] 2. Special Retroactive Requirements - § 25.2 [Reserved]

Chapter 2 - Flight

Section 1. General 3. Proof of Compliance - § 25.21. a. Explanation. In an effort to provide the necessary guidelines for the flight test evaluation of transport category airplanes, without producing a cumbersome document, this AC assumes a conventional transport airplane configuration. In general, a conventional airplane configuration is one with distinct wing and fuselage elements that are joined together, aftmounted horizontal and vertical stabilizers that are attached to the fuselage, and propulsion provided either by turbojet/turbofan engines that do not provide any significant increase in lift due to their operation or engine-driven propellers. The effects of non-conventional airplane configurations (e.g., blown flaps) on the compliance methods should be evaluated and determined based on the intent of the guidelines presented for conventional airplane configurations. (1) Section 25.21(a) - Proof of Compliance. (a) The burden of showing compliance with the flight requirements for an airworthiness certificate or a type certificate rests with the applicant.

Chapter 2 - Flight

The applicant should, at his own expense and risk, conduct such official flight tests as required by the FAA to demonstrate compliance with the applicable requirements. During the certification process, the applicant should make available the airplane, as well as all of the personnel and equipment necessary to obtain and process the required data. (b) If the airplane flight characteristics or the required flight data are affected by weight and/or center of gravity (c.g.), the compliance data must be presented for the most critical weight and c.g. position per § 25.21(a).

Unless the applicant shows that the allowable c.g. travel in one or more axes (e.g., lateral fuel imbalance) has a negligible effect on compliance with the airworthiness requirements, the applicant must substantiate compliance at the critical c.g. (c) The gross weight and c.g. tolerances specified in paragraphs 3a(3)(b)1 and 3 are test tolerances and are not intended to allow compliance to be shown at less than critical conditions. (d) Section 21.35(a)(3) requires that the test airplane be in conformity with its type design specifications. 1 This means that the test airplane must be in conformity with its type design specification as relates to the particular test being conducted. 2 Any deviation from conformity must be clearly shown to be of no consequence to the particular test being conducted. For example, if the slip resistant escape surface required by § 25.810(c) is not installed, the applicant must show that its presence would have no effect on measured airplane performance and flight characteristics.

(e) Section 21.35(b)(2) requires the applicant to conduct sufficient flight testing the FAA finds necessary to determine whether there is reasonable assurance that the airplane, its components, and its equipment are reliable and function properly. Appendix 2 to this AC provides guidance for showing compliance with this requirement. (2) Section 25.21(c) - Proof of Compliance (Altitude Effect on Flight Characteristics). (a) Any of the flying qualities, including controllability, stability, trim, and stall characteristics, affected by altitude must be investigated for the most adverse altitude conditions approved for operations. (b) Consideration should be given in the test program to aerodynamic control system changes with altitude (e.g., control throws or auto slats which are sometimes inhibited by Mach number at altitude). (3) Section 25.21(d) - Proof of Compliance (Flight Test Tolerances). (a) To allow for variations from precise test values, acceptable tolerances during flight testing must be maintained.

The purpose of these tolerances is to allow for variations in flight test values from which data are acceptable for reduction to the value desired. They are not intended for tests to be routinely scheduled at the lower weights, or to allow for compliance to be shown at less than the critical condition; nor are they to be considered as allowable inaccuracy of measurement. As an example, when demonstrating stability with a specified trim speed of 1.3 VSR1, the trim speed may be 1.3 VSR1 +3 knots or 3 percent; however, no positive tolerance is permitted when demonstrating the minimum prescribed trim speed of 1.3 VSR1 (Ref. § 25.161). (b) Where variation in the parameter on which a tolerance is allowed will have an effect on the results of the test, the results should be corrected to the most critical value of that parameter within the operating envelope being approved. If such a correction is impossible or impractical (e.g., performance at forward c.g.), the average test conditions should assure that the measured characteristics represent the actual critical value. 1 Weight limits.

Figure 3-1, below, presents weight tolerances that have been found acceptable for the specified flight tests. Many flight tests need to be conducted at or very near the maximum operating weight for the airplane configuration, particularly those tests used to establish airplane flight manual (AFM) performance information. As noted in paragraph (a) above, the purpose of the test tolerances is to allow for variations in flight test values, not to routinely schedule tests at less than critical weight conditions or to allow for compliance to be shown at less than the critical weight condition.

Figure 3-1. Weight Tolerance Limits

Flight Test Conditions Weight

Tolerance Limit

+5% +10%

Stall Speeds X

Stall Characteristics X

Climb Performance X

Takeoff Flight Paths X

Landing Braking Distance X

Landing Air Distance X

Takeoff Distance & Speed X

Accelerate-Stop Distance X

Maximum Energy RTOs X

Minimum Unstick Speed X

(aa) For follow-on airplane certification programs (e.g., minor gross weight increase), where it is desired to use an existing certificated data base from an aerodynamically similar model of the same airplane type, the test weight tolerance limits of figure 3-1 have also been applied as extrapolation limits to minimize additional test requirements.

(bb) For follow-on airplane certification programs, test data may be extrapolated to higher gross weights than specified in figure 3-1, if the available test data include an adequate range of weights and an appropriate number of points at the highest weight tested. If the test data analysis verifies the predicted effect of weight, then other extrapolation limits may apply.

(cc) Equivalent weight extrapolation limits. For follow-on airplane certification programs where it is desired to increase a maximum operating weight based on existing certified performance parameters that have weight as one of their independent terms, those parameters should be examined for equivalent compliance with the weight tolerance limits of figure 3-1. An example would be the reduction of an airplane’s landing flap position, to one approved on a similar model of the same airplane type, which would incur an increase in landing speeds and brake energy, relative to the original certificated landing flap, at any given weight. The brake energy, at the maximum certificated landing weight, should be calculated for the reduced landing flap. This brake energy should account for the increased landing speeds and reduced aerodynamic drag associated with the reduced flap setting. It should then be determined what equivalent gross weight would have rendered that brake energy with the original landing flap (see figure 3-2). The resulting equivalent gross weight should not exceed the certificated

maximum landing weight by more than the five percent weight extrapolation limit specified in figure 3-1. If the equivalent gross weight (at the existing landing flap setting) is not more than five percent greater than the certificated maximum landing weight, the reduced flap certification may be eligible for a limited flight test program (e.g., stall speed verification, handling characteristics, and qualitative landing demonstration). Further limitations may be imposed by the criteria of technical standard order (TSO) C135a (“Transport Airplane Wheels and Wheel and Brake Assemblies,” dated July 1, 2009).

Figure 3-2. Equivalent Weight Extrapolation

2 Wind Limits. For takeoff and landing tests, a wind velocity limit of 10 knots (from any direction) or 0.11 VSR1 (whichever is lower) at the height of the mean aerodynamic chord (MAC), as determined with the airplane in a static ground attitude, has been considered the maximum acceptable. When test wind velocity is to be measured at the wing MAC height, a measurement height of six feet above the ground should be considered as a limit to avoid possible measurement inaccuracies due to surface interference. Because of likely unsteady wind conditions, it is generally considered that takeoff and landing performance data obtained under runway wind conditions greater than 5 knots are likely to be inconsistent and unreliable. If performance data are obtained with winds greater than 5 knots, these data should not necessarily be ignored.

3 C.G. Limits. A test tolerance of +7 percent of the total c.g. range is intended to allow some practical relief for inflight c.g. movement. This relief is only acceptable when the test data general scatter is on both sides of the limiting c.g. or when c.g. correction from test c.g. to limit c.g. is acceptable.

4 Airspeed Limits. Normally, tests conducted within 3 percent or 3 knots (whichever is the higher) of the desired test speed are considered acceptable.

5 Thrust Limits. Thrust critical tests, such as minimum control speeds, should be conducted at the highest thrust (power) allowable on the engine given the constraints of temperature and altitude. It is then permitted to calculate further corrections to allow extrapolation of data to cover the entire operating envelope. These thrust corrections should be limited to 5 percent of test day thrust, unless a detailed analysis is performed. (See Appendix 7 of this AC).

(c) Because the tolerance values normally are not considered in the airplane design substantiation, it is not the purpose of these tolerances to allow flights at values in excess of those authorized in the type design. If such flights are to be conducted, adequate structural substantiation for the flight conditions should be available. These flights, however, are always conducted under controlled conditions and with the flight test crew’s full cognizance of the situation. Examples of such flights are:

1 Takeoff at greater than maximum takeoff weight for the purpose of reaching a test area at the maximum takeoff weight.

2 Landing at greater than maximum landing weights during the course of conducting takeoff tests.

3 Flights to obtain data for future approvals beyond that substantiated for the initial type design.

(d) The table in figure 3-3 indicates the cases in which corrections are normally allowed. Any corrections to flight test data should be made by methods that are agreed to by the FAA.

Figure 3-3. Test Parameters That Normally Can Be Corrected

Flight Test

Condition

Correctable Parameters

Wt. C.G. Airspeed Altitude Power/

Thrust

Wind

Airspeed calibration X --- --- --- --- ---

Stall speeds X X --- --- X ---

Climb performance X X X X X ---

Landing performance X --- X X --- X

Takeoff performance X X --- X X X

Accelerate-stop perf. X X --- X X X

Minimum control speed --- --- --- --- X ---

Minimum unstick speed X X X --- X ---

Buffet boundary X X --- X --- ---

(e) All instrumentation used in the flight test program should be appropriately calibrated and acceptable to the FAA test team.

(4) Section 25.21(f) - Proof of Compliance (Wind Measurement and Corrections). The relationship between the wind measured at one height and the corresponding wind at another height may be obtained by the following equation:

VW2 = VW1(H2/H1)1/7

VW2 = VW1(H2/H1)1/7

Where: H = Height above the runway surface

VW2 = Wind velocity at H2 VW1 = Wind velocity at H1

This equation is presented graphically below. Values of H less than 5 feet should not be used in this relationship.

Figure 3-4. Wind Profile Variation

(5) Wind Profile Variation for Test Data. The performance data of airplanes should be obtained in such a manner that the effect of wind on the test data may be determined. The test wind velocity should be corrected from the recorded height above the test surface to the height of the airplane wing mean-aerodynamic-chord. If the wind profile variation is not measured, the variation may be calculated using the equation in paragraph (4) above. The following examples are methods of handling wind profile variation data. Other methods have also been found acceptable. Example: Test Data

Given: o Height of mean-aerodynamic-chord with airplane on surface 8.0 ft. o Height of wind measurement 6.0 ft. o Measured wind velocity 4.8 kts.

0

10

20

30

40

50

60

70

0 10 20 30 40 50 60

WIND VELOCITY - KNOTS

WIND VELOCITY - KNOTS

HEIGHT ABOVE FIELD ELEVATION - FEET

10 meters

Results: o Test wind velocity with airplane 50 ft. above landing surface 4.8((50 + 8)/6)1/7 = 6.6 kts. o Test wind velocity with airplane 35 ft. above takeoff surface 4.8((35 + 8)/6)1/7 = 6.4 kts. o Test wind velocity with airplane on surface 4.8(8/6)1/7 = 5.0 kts.

HEIGHT ABOVE FIELD ELEVATION - FEET

(6) Wind Profile Variation for AFM Data. When expanding the data to the AFM conditions, the result should include the effective velocity, at the airplane’s wing meanaerodynamic-chord, which corresponds to the wind condition as measured at 10 meters (32.81 ft.) above the takeoff surface, and corrected for wind factors of § 25.105(d)(1).

Example: Airplane Flight Manual Data Given: o Height of mean-aerodynamic-chord with airplane on surface 8.0 ft. o Reported head wind at 10 meters 40.0 kts. o Section 25.105(d)(1) wind factor 0.5 Results: o Factored wind velocity with airplane 50 ft. above landing surface (0.5)(40)((50 + 8)/32.81)1/7 = 21.7 kts. o Factored wind velocity with airplane 35 ft. above takeoff surface (0.5)(40)((35 + 8)/32.81)1/7 = 20.8 kts. o Factored wind velocity with airplane on surface (0.5)(40)(8/32.81)1/7 = 16.3 kts.

(7) Airplane Airspeed Variation Due to Wind Profile Variation With Simultaneous Speed Changes Due to Airplane Dynamic Performance. In the reduction of test data and in the expansion of such data to AFM conditions, the increase or decrease of speed due to the dynamic effect of the forces on the airplane are manifested by only the change in ground speed. These changes in speed (zero wind speed changes) may be generalized either as speed increments or

speed ratios. The changes in airspeed due to wind profile are superimposed on these speed changes.

Example: Takeoff Test Data Given: o True airspeed at liftoff, VLOF 144.0 kts. o True airspeed at 35 ft. above takeoff surface 147.0 kts. o Test wind at liftoff 5.0 kts. o Test wind with airplane 35 ft. above takeoff surface 6.4 kts. Results: o Speed change due to airplane dynamic performance, zero wind speed change (V35-VLOF) = (147-6.4)-(144-5.0) 1.6 kts. Example: Takeoff--Airplane Flight Manual Data

Given: o Factored wind at liftoff 16.3 kts. o Factored wind with airplane 35 ft. above takeoff surface 20.8 kts. o Zero wind speed change, (V35-VLOF) 1.6 kts. o Zero wind speed change, (VLOF-VR) 0.5 kts. o True airspeed required at 35 ft. 150.0 kts. Results: o Ground speed required at 35 ft. 150-20.8 = 129.2 kts. o Ground speed at liftoff 129.2-1.6 = 127.6 kts. o True airspeed at liftoff 127.6+16.3 = 143.9 kts. o Ground speed at rotation 127.6-0.5 = 127.1 kts. o True airspeed at rotation (for distance calculations) 127.1+16.3 = 143.4 kts. o Airplane flight manual rotation speed, true airspeed 150-0.5-1.6 = 147.9 kts.

NOTE: The indicated airspeed at rotation (VR), given in the AFM, should be predicated on the required speed at 35 ft. minus the speed increment (V35-VR) assuming no airspeed change due to wind profile (i.e., use the “zero wind speed change” increments shown above). The proper rotation speed, assuming the airplane will gain 4.5 knots due to wind profile, is 143.4 knots. However, if this airspeed increase does not materialize, the airplane will be slow by 4.5 knots at 35 feet. It is therefore more desirable to allow the airplane to attain this 4.5 knots on the ground. Any reduction in field length margin of safety by this increase in VR

is adequately compensated for by the 50 percent wind factor. This also eliminates a requirement to adjust VR for wind. However, in calculating the AFM field lengths, the airspeed attained due to wind profile may be included.

Example: Landing--AFM Data Given: o Factored wind with airplane 50 ft. above landing surface 21.7 kts. o Factored wind with airplane on landing surface 16.3 kts. o Zero wind speed change for 50 ft. to touchdown (V50-VTD) 4.0 kts. o True airspeed required at 50 ft. 130.0 kts. Results: o Ground speed at 50 ft. 130-21.7 = 108.3 kts. o Ground speed at touchdown 108.3-4.0 = 104.3 kts. o True airspeed at touchdown 104.3+16.3 = 120.6 kts.

(8) Expansion of Takeoff and Landing Data for a Range of Airport Elevations.

(a) These guidelines apply to expanding AFM takeoff and landing data above and below the altitude at which the airplane takeoff and landing performance tests are conducted.

(b) Historically, limits were placed on the extrapolation of takeoff data. In the past, takeoff data could generally be extrapolated 6,000 feet above and 3,000 feet below the test field elevation when proven testing and data reduction methods were used. For extrapolations beyond these limits, a 2 percent takeoff distance penalty was to be applied for every additional 1,000 feet extrapolation. Such limitations were generally not applied to extrapolation of landing data, provided the effect of the higher true airspeed on landing distance was taken into account.

(c) Since then, considerably more experience has been gained both in terms of modeling airplane and propulsion system (i.e., turbine engines and propellers, where appropriate) performance and in verifying the accuracy of these models for determining high (and low) altitude takeoff and landing performance. This experience has shown that the soundness of the extrapolation is primarily a function of the accuracy of the propulsion system performance model and its integration with the airplane drag model. The basic aerodynamic characteristics of the airplane do not change significantly with altitude or ambient temperature, and any such effects are readily taken into account by standard airplane performance modeling practices.

(d) As a result, with installed propulsion system performance characteristics that have been adequately defined and verified, airplane takeoff and landing performance data obtained at one field elevation may be extrapolated to higher and lower altitudes within the limits of the operating envelope without applying additional performance conservatisms. It should be noted, however, that extrapolation of the propulsion system data used in the

determination and validation of propulsion system performance characteristics is typically limited to 3,000 feet above the highest altitude at which propulsion system parameters were evaluated for the pertinent power/ thrust setting. (See paragraph 9 of this AC for more information on an acceptable means of establishing and verifying installed propulsion system performance characteristics.)

(e) Note that certification testing for operation at airports that are above 8,000 feet should also include functional tests of the cabin pressurization system in accordance with paragraph 87b(3) of this AC. Consideration should be given to any sensitivity to, or dependency upon airport altitude, such as: engine and APU starting, passenger oxygen, autopilot, autoland, autothrottle system thrust set/operation.

(9) Tailwind Takeoff and Landing.

(a) Wind Velocities of 10 Knots or Less - Approval may be given for performance, controllability, and engine operating characteristics for operations in reported tailwind velocities up to 10 knots, measured at a 10 meter height, without specific flight tests.

(b) Wind Velocities Greater than 10 Knots.

1 Performance. It is considered that takeoff, rejected takeoff, and landing distances, measured in tailwind conditions greater than 10 knots, are unreliable for use in determining airplane performance. Wind conditions of such magnitude are generally not sufficiently consistent over the length of the runway or over the time period required to perform the test maneuver. The 150 percent operational tailwind velocity factor, required by §§ 25.105(d)(1) and 25.125(f), affords a satisfactory method for determination of airplane takeoff and landing performance information and limitations up to a limiting tailwind velocity of 15 knots when using a flight test data base obtained under zero wind conditions.

NOTE: The design requirements of § 25.479 (Level landing conditions) also require the effects of increased contact speeds to be investigated if approval for landings with tailwinds greater than 10 knots is desired.

2 Control Characteristics. Airplane control characteristics should be evaluated under the following conditions with the center of gravity at the aft limit and the test tailwind velocity equal to the proposed limit tailwind factored by 150 percent:

(aa) Takeoff. At light weight with maximum approved takeoff flap deflection, both all-engines operating and one-engine inoperative takeoffs should be evaluated.

(bb) Landing. Approach and landing at light weight with maximum approved landing flap deflection.

(cc) Determination of the increased ground speed effect on gear vibration, shimmy, flight director and/or autopilot instrument landing system (ILS) approaches, ground proximity warning systems (GPWS) sink rate modes, etc.

(dd) If engine idle thrust is increased to account for the increased tailwind velocity, ensure that deviations above the glideslope are recoverable.

3 Weight Limits. Consistent with the requirements of §§ 25.105(d)(1) and 25.125(f), the maximum takeoff and maximum quick turnaround weights should be determined using brake energies and tire speeds, as appropriate, calculated with the limit tailwind velocity factored by 150 percent.

4 Engine Operating Characteristics. Satisfactory engine operation should be demonstrated at the limit tailwind velocity factored by 150 percent. The demonstrations should include:

(aa) Zero groundspeed operation. (bb) Takeoff power setting procedure used for AFM performance (typically completed by approximately 80 knots), both manually and automatically (autothrottle).

(cc) Reverse thrust operations. 5 Airplane Flight Manual. The AFM should contain a statement that the limitation for tailwinds greater than 10 knots reflects the capability of the airplane as evaluated in terms of airworthiness but does not constitute approval for operation in tailwinds exceeding 10 knots.

b. Procedures. (1) The performance-related flight test procedures are discussed in each of the following paragraphs of this AC:

10. Takeoff and Takeoff Speeds 11. Accelerate-Stop Distance 12. Takeoff Path 13. Takeoff Distance and Takeoff Run 14. Takeoff Flight Path 15. Climb: General 16. Landing Climb 17. Climb: One Engine Inoperative 18. En Route Flight Path 19. Landing

(2) Performance Data for Multiple Flap or Additional Flap Positions. If approval of performance data is requested for flap settings at which no test data are available, the data may be obtained from interpolation of flight data obtained at no less than four flap settings that are within a constant configuration of other lift devices. If the span of flap settings is small and

previously obtained data provide sufficient confidence (i.e., the shape of the curves are known and lend themselves to accurate interpolation), data from three flap settings may be acceptable.

(3) Flight Characteristics for Abnormal Configurations (Ref. § 25.671(c)).

(a) For purposes of this AC, an abnormal configuration is an operational configuration that results from any single failure or any combination of failures not shown to be improbable.

(b) Flight characteristics for abnormal configurations may be determined by test or analysis to assure that the airplane is capable of continued safe flight and landing. Flight tests, if required, should be conducted at the critical conditions of altitude, weight, c.g., and engine thrust associated with the configuration, and at the most critical airspeed between the speed reached one second after stall warning occurs (see paragraph 29e(2)(h) of this AC) and the maximum operating airspeed for the configuration. 4. Load Distribution Limits - § 25.23 [Reserved]. 5. Weight Limits and Center of Gravity Limits - §§ 25.25 and 25.27 [Reserved]. 6. Empty Weight and Corresponding Center of Gravity - § 25.29 [Reserved]. 7. Removable Ballast - § 25.31 [Reserved]. 8. Propeller Speed and Pitch Limits - § 25.33.

a. Explanation. None. b. Procedures. The tachometers and the airspeed indicating system of the test airplane should have been calibrated within the last six months. With those conditions satisfied, the following should be accomplished:

(1) Determine that the propeller speeds and pitch settings are safe and satisfactory during all tests that are conducted in the flight test program within the certification limits of the airplane, engine, and propeller. This includes establishing acceptable low pitch (flight idle) blade angles on turbopropeller airplanes and verifying that propeller configurations are satisfactory at VMO/MMO to prevent propeller overspeed.

(2) Determine that the propeller speeds and pitch settings are safe and satisfactory during all tests that are conducted to satisfy the performance requirements.

(3) With the propeller governors operative and the propeller controls in full high revolutions per minute (r.p.m.) position, determine that the maximum takeoff power settings do

not exceed the rated takeoff r.p.m. of each engine during takeoff and climb at the best rate-ofclimb speed.

(4) With the propeller governors made inoperative by mechanical means, determine the maximum power, no-wind, static r.p.m.’s. With the propeller governors operating on the low pitch stop, the engine speeds must not exceed 103 percent of the maximum allowable takeoff r.p.m. or 99 percent of an approved maximum overspeed, as required by § 25.33(c). On turbopropeller engines, the engine speeds should not exceed the maximum engine speeds allowed by engine and propeller type designs. Note which systems were disabled and how the disablement was done. If maximum takeoff power torque or sea level standard conditions cannot be obtained on the test day, correct the data to these conditions by an acceptable means. A nowind condition is considered to be a wind of 5 knots or less. The static r.p.m. should be the average obtained with a direct crosswind from the left and a direct crosswind from the right.

(5) If the above determinations are satisfactory, then measure the low-pitch stop setting and the high-pitch stop setting. These data may have been obtained from the propeller manufacturer and may be used, provided the pitch stops have not been changed since the manufacturer delivered the propeller. If measured, the blade station should be recorded. Include these blade angles in the type certificate data sheet.

Section 2. Performance 9. General - § 25.101. a. Explanation. - Propulsion System Behavior. Section 25.101(c) requires that airplane “performance must correspond to the propulsive thrust available under the particular ambient atmospheric conditions, the particular flight conditions....” The propulsion system’s (i.e., turbine engines and propellers, where appropriate), installed performance characteristics are primarily a function of engine power setting, airspeed, propeller efficiency (where applicable), altitude, and ambient temperature. Determine the effects of each of these variables to establish the thrust available for airplane performance calculations.

b. Procedures.

(1) The intent is to develop a model of propulsion system performance that covers the approved flight envelope. Furthermore, it should be shown that the combination of the propulsion system performance model and the airplane performance model is validated by the takeoff performance test data, climb performance tests, and tests used to determine airplane drag. Installed propulsion system performance characteristics may be established via the following tests and analyses:

(a) Steady-state engine power setting vs. thrust (or power) testing. Engines should be equipped with adequate instrumentation to allow the determination of thrust (or power). Data should be acquired in order to validate the model, including propeller-installed

thrust, if applicable, over the range of power settings, altitudes, temperatures, and airspeeds for which approval is sought. Although it is not possible to definitively list or foresee all of the types of instrumentation that might be considered adequate for determining thrust (or power) output, two examples used in past certification programs are: (1) engine pressure rakes, with engines calibrated in a ground test cell, and (2) fan speed, with engines calibrated in a ground test cell and the calibration data validated by the use of a flying test bed. In any case, the applicant should substantiate the adequacy of the instrumentation to be used for determining the thrust (or power) output.

(b) Lapse rate takeoff testing to characterize the behavior of power setting, rotor speeds, propeller effects (i.e., torque, RPM, and blade angle), or gas temperature as a function of time, thermal state, or airspeed, as appropriate. These tests should include the operation of an automatic takeoff thrust control system (ATTCS), if applicable, and should cover the range of power settings for which approval is sought.

1 Data for higher altitude power settings may be acquired via overboost (i.e., operating at a higher than normal power setting for the conditions) with the consent of the engine and propeller manufacturer(s), when applicable. When considering the use of overboost on turbopropeller propulsion system installations to simulate higher altitude and ambient temperature range conditions, the capability to achieve an appropriate simulation should be evaluated based on the engine and propeller control system(s) and aircraft performance and structural considerations. Engine (gearbox) torque, rotor speed, or gas temperature limits, including protection devices to prohibit or limit exceedances, may prevent the required amount of overboost needed for performance at the maximum airport altitude sought for approval. Overboost may be considered as increased torque, reduced propeller speed, or a combination of both, in order to achieve the appropriate blade angle for the higher altitude and ambient temperature range simulation. Consideration for extrapolations will depend on the applicant’s substantiation of the proper turbopropeller propulsion system simulated test conditions.

2 Lapse rate characteristics should be validated by takeoff demonstrations at the maximum airport altitude for which takeoff approval is being sought. Alternatively, if overboost (see paragraph 1 above) is used to simulate the thrust setting parameters of the maximum airport altitude for which takeoff approval is sought, the takeoff demonstrations of lapse rate characteristics can be performed at an airport altitude up to 3,000 feet lower than the maximum airport altitude.

(c) Thrust calculation substantiation. Installed thrust should be calculated via a mathematical model of the propulsion system, or other appropriate means, adjusted as necessary to match the measured inflight performance characteristics of the installed propulsion system. The propulsion system mathematical model should define the relationship of thrust to the power setting parameter over the range of power setting, airspeed, altitude, and temperature for which approval is sought. For turbojet airplanes, the propulsion system mathematical model should be substantiated by ground tests in which thrust is directly measured via a calibrated load cell or equivalent means. For turbopropeller airplanes, the engine power measurement should be substantiated by a calibrated dynamometer or equivalent means, the engine jet thrust should be

established by an acceptable engine model, and the propeller thrust and power characteristics should be substantiated by wind tunnel testing or equivalent means.

(d) Effects of ambient temperature. The flight tests of paragraph 9b(l)(a) above will typically provide data over a broad range of ambient temperatures. Additional data may be obtained from other flight or ground tests of the same type or series of engine. The objective is to confirm that the propulsion system model accurately reflects the effect of temperature over the range of ambient temperatures for which approval is being sought (operating envelope). Because thrust (or power) data can usually be normalized versus temperature using either dimensionless variables (e.g., theta exponents or a thermodynamic cycle model), it is usually unnecessary to obtain data over the entire ambient temperature range. There is no need to conduct additional testing if:

1 The data show that the behavior of thrust and limiting parameters versus ambient temperature can be predicted accurately, and

2 Analysis based upon the test data shows that the propulsion system will operate at rated thrust without exceeding propulsion system limits.

(2) Extrapolation of propulsion system performance data to 3,000 feet above the highest airport altitude tested (but no higher than the maximum takeoff airport altitude to be approved) is acceptable, provided the supporting data, including flight test and propulsion system operations data (e.g., engine and propeller control, limits exceedance, and surge protection devices scheduling), substantiates the proposed extrapolation procedures. Considerations for extrapolation depend upon an applicant’s determination, understanding, and substantiation of the critical operating modes of the propulsion system. This understanding includes a determination and quantification of the effects that propulsion system installation and variations in ambient conditions have on these modes. 10. Takeoff and Takeoff Speeds - §§ 25.105 and 25.107.

a. Explanation. The primary objective of the takeoff tests required by § 25.107 is to determine the takeoff speed schedule for all takeoff configurations at all weight, altitude, and temperature conditions within the operational limits selected by the applicant. The provisions of § 25.105 are self evident and are not repeated or amplified in this discussion. Guidance material for unpaved runway evaluation is contained in Chapter 8 (paragraph 232) of this AC.

b. Procedures. Although the following speed definitions are given in terms of calibrated airspeed, the AFM presentations should be given in terms of indicated airspeed. Attention should be paid to all potential sources of airspeed error, but special consideration should be given to airplanes with electronic instruments in the cockpit that apply electronic filtering to the airspeed data. This filtering, which causes a time delay in the airspeed indication, can be a source of significant systematic error in the presentation of airspeed to the flightcrew. During a normal takeoff acceleration, the airplane will be at a higher speed than is indicated by the cockpit instrument, which can result in longer distances than are presented in the AFM, particularly in the event of a rejected takeoff near the indicated V1 speed. The effects of any time delays caused

by electronic filtering, pneumatic system lag, or other sources should be adequately addressed in the AFM speed and distance presentations. Further explanation of airspeed lag, particularly pertaining to airplanes with electronic instruments in the cockpit, and procedures for calibrating the airspeed indicating system (§ 25.1323(b)) are presented in paragraph 177 of this AC.

(1) Section 25.107(a)(1) - Engine Failure Speed (VEF). The engine failure speed (VEF) is defined as the calibrated airspeed at which the critical engine is assumed to fail and must be selected by the applicant. VEF cannot be less than the ground minimum control speed (VMCG).

(2) Section 25.107(a)(2) - Takeoff Decision Speed (V1). The takeoff decision speed (V1) may not be less than VEF plus the speed gained with the critical engine inoperative during the time interval between VEF and the instant at which the pilot takes action after recognizing the engine failure. This is indicated by pilot application of the first deceleration device such as brakes, throttles, spoilers, etc. during accelerate-stop tests, or by the first control input during VMCG testing. The applicant may choose the sequence of events. Refer to paragraph 11 of this AC, addressing § 25.109, for a more complete description of rejected takeoff (RTO) transition procedures and associated time delays. If it becomes evident in expansion of takeoff data for the AFM that excessive variation in V1 exists, resulting from the many performance variables involved (variations of +1.5 knots or +100 ft. have been found acceptable), then measures should be taken to ensure that scheduled performance variations are not excessive. Examples of such measures are small field length factors, or increments, and multiple web charts (acceleratego/stop, V1/VR) for a particular configuration.

(3) Section 25.107(b) - Minimum Takeoff Safety Speed (V2MIN).

(a) V2MIN, in terms of calibrated airspeed, cannot be less than:

1 1.1 times the VMCA defined in § 25.149.

2 1.13 times VSR for two-engine and three-engine turbopropeller and reciprocating engine-powered airplanes and for all turbojet airplanes that do not have provisions for obtaining significant reduction in the one-engine inoperative power-on stalling speed (i.e., boundary layer control, blown flaps, etc.). The value of VS to be used in determining V2MIN is the stall speed in the applicable takeoff configuration, landing gear retracted, except for those airplanes with a fixed landing gear or for gear-down dispatch.

(b) V2MIN may be reduced to 1.08 times VSR for turbopropeller and reciprocating engine-powered airplanes with more than three engines, and turbojet powered airplanes with adequate provisions for obtaining significant power-on stall speed reduction through the use of such things as boundary layer control, blown flaps, etc.

(c) For propeller-driven airplanes, the difference between the two margins, based upon the number of engines installed on the airplane, is because the application of power ordinarily reduces the stalling speed appreciably. In the case of the two-engine propeller-driven airplane, at least half of this reduction is eliminated by the failure of an engine. The difference in the required factors therefore provides approximately the same margin over the actual stalling speed under the power-on conditions that are obtained after the loss of an engine, no matter what the number of engines (in excess of one) may be. Unlike the propeller-driven airplane, the turbojet/turbofan powered airplane does not show any appreciable difference between the poweron and power-off stalling speed. This is due to the absence of the propeller, which ordinarily induces a slipstream with the application of power causing the wing to retain its lift to a speed lower than the power-off stalling speed. The applicant’s selection of the two speeds specified will influence the nature of the testing required in establishing the takeoff flight path.

(4) Section 25.107(c) - Takeoff Safety Speed (V2). V2 is the calibrated airspeed that is attained at or before the airplane reaches a height of 35 ft. above the takeoff surface after an engine failure at VEF using an established rotation speed (VR). During the takeoff speeds demonstration, V2 should be continued to an altitude sufficient to assure stable conditions beyond the 35 ft height. V2 cannot be less than V2MIN. In addition, V2 cannot be less than the liftoff speed, VLOF, which is defined in § 25.107(f). In accordance with § 25.107(c), V2 in terms of calibrated airspeed may not be less than VR plus the speed increment attained before reaching a height of 35 feet above the takeoff surface and a speed that provides the maneuvering capability specified in § 25.143(h). Section 25.111(c)(2) stipulates that the airplane must reach V2 before it is 35 feet above the takeoff surface and continue at a speed not less than V2 until it is 400 feet above the takeoff surface. These requirements were first expressed in SR-422A, paragraphs 4T.114(b)(4) and (c)(3) and 4T.116(e).

The intent of these requirements is discussed in the preamble to SR-422A, which states, in part, “For these reasons, this regulation permits the airplane to lift off the ground at a speed lower than the V2 speed. The concern that the regulation change was addressing was the overshoot of V2 after liftoff when it was required that the airplane attain V2 on, or near, the ground. It was therefore the intent of the regulation to allow an acceleration to V2 after liftoff but not to allow a decrease in the field length required to attain a height of 35 feet above the takeoff surface by attaining a speed greater than V2, under low drag ground conditions, and using the excess kinetic energy to attain the 35 foot height.

(a) In the case of turbojet powered airplanes, when the bulk of the one-engineinoperative data have been determined with idle cuts, V2, and its relationship to VR, should be substantiated by a limited number of fuel cuts at VEF. For derivative programs not involving a new or modified engine type (i.e., a modification that would affect thrust decay characteristics), fuel cuts are unnecessary if thrust decay characteristics have been adequately substantiated.

(b) For propeller-driven airplanes, the use of fuel cuts can be more important in order to ensure that the takeoff speeds and distances are obtained with the critical engine’s propeller attaining the position it would during a sudden engine failure. The number of tests that should be conducted using fuel cuts, if any, depends on the correlation obtained with the idle cut data and substantiation that the data analysis methodology adequately models the effects of a sudden engine failure.

(5) Section 25.107(d) - Minimum Unstick Speed (VMU).

(a) An applicant should comply with § 25.107(d) by conducting minimum unstick speed (VMU) determination tests with all engines operating and with one engine inoperative. If a stick pusher is installed, it should normally be active and set to the minimum angle-of-attack side of its rigging tolerance band. If desired, artificial stall warning systems may be disabled for this demonstration. (See paragraph (f) below for further discussion regarding the setting of stick pusher and stall warning systems during VMU testing.) During this demonstration, the takeoff should be continued until the airplane is out of ground effect. The airplane pitch attitude should not be decreased after liftoff.

(b) In lieu of conducting actual one-engine-inoperative VMU tests, the applicant may conduct all-engines-operating VMU tests that simulate and account for all pertinent factors that would be associated with an actual one-engine-inoperative VMU test. To account fully for pertinent factors, it may be necessary to adjust the resulting VMU test values analytically. The factors to be accounted for should include at least the following:

1 Thrust/weight ratio for the one-engine-inoperative range.

2 Controllability (may be related to one-engine-inoperative free air tests, such as VS, VMCA, etc.).

3 Increased drag due to lateral/directional control systems.

4 Reduced lift due to devices such as wing spoilers used for lateral control.

5 Adverse effects of any other systems or devices on control, drag, or lift.

(c) The number of VMU tests required may be minimized by testing only the critical all-engines-operating and one-engine-inoperative thrust/weight ratios, provided that the VMU speeds determined at these critical conditions are used for the range of thrust/weights appropriate to the all-engines-operating and one-engine-inoperative configurations. The critical thrust/weight is established by correcting, to the VMU speed, the thrust that results in the airplane achieving its limiting one-engine-inoperative climb gradient at the normally scheduled speed and in the appropriate configuration.

(d) Amendment 25-42, effective March 1, 1978, revised §§ 25.107(d) and 25.107(e)(1)(iv) in order to permit the one-engine-inoperative VMU to be determined by allengines-operating tests at the thrust/weight ratio corresponding to the one-engine-inoperative

condition. As revised, § 25.107(d) specifies that VMU must be selected for the range of thrust/weight ratios to be certificated, rather than for the all-engines-operating and one-engineinoperative conditions as was previously required. In determining the all-engines-operating thrust/weight ratio that corresponds to the one-engine-inoperative condition, consideration should be given to trim and control drag differences between the two configurations in addition to the effect of the number of engines operating. The minimum thrust/weight ratio to be certificated is established by correcting, to the VMU speed, the thrust that results in the airplane achieving its limiting engine-out climb gradient in the appropriate configuration and at the normally scheduled speed.

(e) To conduct the VMU tests, rotate the airplane as necessary to achieve the VMU attitude. It is acceptable to use some additional nose-up trim over the normal trim setting during VMU demonstrations. If additional nose-up trim is required, the additional considerations of paragraph (g), below, apply. VMU is the speed at which the weight of the airplane is completely supported by aerodynamic lift and thrust forces. Some judgment may be necessary on airplanes that have tilting main landing gear bogies. Determining the liftoff point from gear loads and wheel speeds has been found acceptable in past programs. After liftoff, the airplane should be flown out of ground effect. During liftoff and the subsequent climbout, the airplane should be fully controllable.

(f) VMU testing is a maximum performance flight test maneuver, and liftoff may occur very near the angle-of-attack for maximum lift coefficient. Also, even though pitch attitude may be held fairly constant during the maneuver, environmental conditions and transiting through ground effect may result in consequential changes in angle-of-attack. It is permissible to lift off at a speed that is below the normal stall warning speed, provided no more than light buffet is encountered. An artificial stall warning system (e.g., a stick shaker) may be disabled during VMU testing, although doing so will require extreme caution and depend upon a thorough knowledge of the airplane’s stall characteristics. If the airplane is equipped with a stick pusher, for flight test safety reasons it should normally be active and set to the minimum angle-of-attack side of its rigging tolerance band. However, depending on the airplane’s stall characteristics and the stick pusher design, disabling the pusher or delaying activation of the system until a safe altitude is reached may be the safer course. Again, this decision should be made only with a thorough knowledge of the airplane’s stall characteristics combined with a complete understanding of the stick pusher design.

(g) VMU Testing for Airplanes Having Limited Pitch Control Authority.

1 For some airplanes with limited pitch control authority, it may not be possible, at forward c.g. and normal trim, to rotate the airplane to a liftoff attitude where the airplane could otherwise perform a clean flyaway at a minimum speed had the required attitude been achieved. This may occur only over a portion of the takeoff weight range in some configurations. When limited pitch control authority is clearly shown to be the case, VMU test conditions may be modified to allow testing aft of the forward c.g. limit and/or with use of more airplane nose-up trim than normal. The VMU data determined with this procedure should be

12/07/11 AC 25-7B Change 1

corrected to those values representative of the appropriate forward limit; the variation of VMU with c.g. may be assumed to be like the variation of free air stalling speed with c.g. Although the development of scheduled takeoff speeds may proceed from these corrected VMU data, additional tests are required (see paragraph 2 below) to check that the relaxed VMU criteria have not neglected problems that might arise from operational variations in rotating airplanes with limited pitch control authority.

2 In the following assurance test, the airplane should demonstrate safe flyaway characteristics.

(aa) Minimum speed liftoff should be demonstrated at the critical forward c.g. limit with normal trim. For airplanes with a cutback forward c.g. at heavy weight, two weight/c.g. conditions should be considered. The heavy weight tests should be conducted at maximum structural or maximum sea level climb-limited weight with the associated forward c.g. The full forward c.g. tests should be conducted at the highest associated weight. These tests should be conducted at minimum thrust/weight for both the simulated one-engine-inoperative test (symmetrical reduced thrust) and the all-engines-operating case.

(bb) One acceptable test technique is to hold full nose-up control column as the airplane accelerates. As pitch attitude is achieved to establish the minimum liftoff speed, pitch control may be adjusted to prevent overrotation, but the liftoff attitude should be maintained as the airplane flies off the ground and out of ground effect.

(cc) Resulting liftoff speeds do not affect AFM speed schedules if the test proves successful and the resulting liftoff speed is at least 5 knots below the normally scheduled liftoff speed. Adjustments should be made to the scheduled VR, forward c.g. limit, etc., if necessary, to achieve this result.

(dd) This minimum 5 knot reduction below the scheduled liftoff speed provides some leeway for operational variations such as mis-trim, c.g. errors, etc., that could further limit the elevator authority. The reduced VMU margins of the minimum liftoff speeds demonstrated in this test, relative to those specified in § 25.107(e)(1)(iv), result from the reduced probability of a pitch control authority-limited airplane getting into a high drag condition due to overrotation.

(h) VMU Testing for Geometry Limited Airplanes.

1 For airplanes that are geometry limited (i.e., the minimum possible VMU speeds are limited by tail contact with the runway), § 25.107(e)(1)(iv)(B) allows the VMU to VLOF speed margins to be reduced to 108 percent and 104 percent for the all-engines-operating and one-engine-inoperative conditions, respectively. The VMU demonstrated should be sound and repeatable.

2 An airplane that is deemed to be geometry limited at the conditions tested is expected to be geometry limited over its entire takeoff operating envelope. If this is not the

12/07/11 AC 25-7B Change 1

case, the airplane is not considered geometry limited and the reduced VMU to VLOF speed margins do not apply.

3 One acceptable means for demonstrating compliance with §§ 25.107(d) and 25.107(e)(1)(iv) with respect to the capability for a safe liftoff and fly-away from the geometry limited condition is to show that at the lowest thrust-to-weight ratio for the all-enginesoperating condition:

(aa) In the speed range from 96 to 100 percent of the actual liftoff speed, the aft under-surface of the airplane should be in contact with the runway. Because of the dynamic nature of the test, it is recognized that contact will probably not be maintained during this entire speed range, so some judgment is necessary. It has been found acceptable for contact to exist approximately 50 percent of the time that the airplane is in this speed range.

(bb) Beyond the point of liftoff to a height of 35 feet, the airplane’s pitch attitude should not decrease below that at the point of liftoff, nor should the speed increase more than 10 percent.

(cc) The horizontal distance from the start of the takeoff to a height of 35 feet above the takeoff surface should not be greater than 105 percent of the distance determined in accordance with § 25.113(a)(2) without applying the 115 percent factor.

(i) VMU for a Stretched Version of a Tested Airplane.

1 It has been considered that the VMU speed represents the aerodynamic potential minimum liftoff speed related to a safe liftoff and fly-away, even though the body contact attitude may prevent achieving the lift coefficient (CL) for this speed. Such is the case when VMU is determined with body contact, whether or not geometry limited “credit” is sought. It is therefore concluded that a VMU schedule obtained on one model of an airplane type may be applied to a geometry limited stretched version of that tested airplane. The 108 and 104 percent speed factors of § 25.107(e)(1)(iv)(B), as discussed in paragraph 10b(5)(h)1, above, are only applicable to the stretched version if they were applicable to the tested airplane.

2 Since the concern for tail strikes is increased with the stretched airplane, the following should be accomplished, in addition to normal takeoff tests, when applying a shorter body airplane’s VMU schedule to the stretched derivative:

(aa) Scheduled rotation speeds (VR) for the stretched airplane should result in at least the required liftoff speed margins above VMU (i.e., 1.05 and 1.10, or 1.04 and 1.08, as applicable) of the shorter body airplane, corrected for the reduced runway pitch attitude capability and revised c.g. range of the stretched airplane.

(bb) At both the forward and aft c.g. limits, and over the thrust-to-weight range for each takeoff flap, the following abuse takeoff tests should be accomplished. The tests described in paragraphs (i) and (ii), below, should be accomplished with not more than occasional, minor (i.e., non-damaging) tail strikes.

12/07/11 AC 25-7B Change 1

(i) All-engines-operating, early rotation abuse tests specified in paragraph 10b(6)(c)2, including both the rapid rotations and over-rotations as separate test conditions.

(ii) One-engine-inoperative, early rotation abuse tests specified in paragraph 10b(6)(b).

(iii) All-engines-operating, moderate rotation rate (i.e., more rapid than normal) takeoff abuse tests, using the scheduled VR, and normal pitch attitude after liftoff. Tail strikes should not occur for this condition.

(6) Section 25.107(e) - Rotation Speed (VR).

(a) The rotation speed, (VR) in terms of calibrated airspeed, must be selected by the applicant. VR has a number of constraints that must be observed in order to comply with § 25.107(e):

1 VR may not be less than V1; however, it can be equal to V1 in some cases. 2 VR may not be less than 105 percent of the air minimum control speed (VMCA).

3 VR must be a speed that will allow the airplane to reach V2 at or before reaching a height of 35 ft. above the takeoff surface.

4 VR must be a speed that will result in liftoff at a speed not less than 110 percent of VMU (unless geometry limited) for the all-engines-operating condition and not less than 105 percent of the VMU (unless geometry limited) determined at the thrust/weight ratio corresponding to the one-engine-inoperative condition for each set of conditions such as weight, altitude, temperature, and configuration when the airplane is rotated at its maximum practicable rate.

(b) Early rotation, one-engine-inoperative abuse test.

1 In showing compliance with § 25.107(e)(3), some guidance relative to the airspeed attained at the 35 ft. height during the associated flight test is necessary. As this requirement dealing with a rotation speed abuse test only specifies an early rotation (VR-5 knots), it is interpreted that pilot technique is to remain the same as normally used for a oneengine-inoperative condition. With these considerations in mind, it is apparent that the airspeed achieved at the 35 ft. point can be somewhat below the normal scheduled V2 speed. However, the amount of permissible V2 speed reduction should be limited to a reasonable amount as described below.

2 These test criteria are applicable to all unapproved, new, basic model airplanes. They are also applicable to previously approved airplanes when subsequent abuse testing is warranted. However, for those airplanes where the criteria herein are more stringent than that previously applied, consideration will be given to permitting some latitude in the test criteria.

3 In conducting the flight tests required by § 25.107(e)(3), the test pilot should use a normal/natural rotation technique as associated with the use of scheduled takeoff speeds for the airplane being tested. Intentional tail or tail skid contact is not considered acceptable. Further, the airspeed attained at the 35 ft. height during this test should not be less than the scheduled V2 value minus 5 knots. These speed limits should not be considered or used as target V2 test speeds, but rather are intended to provide an acceptable range of speed departure below the scheduled V2 value.

4 In this abuse test, the simulated engine failure should be accomplished sufficiently in advance of the VR test speed to allow for engine spin-down, unless this would be below the VMCG, in which case VMCG should govern. The normal one-engine-inoperative takeoff distance may be analytically adjusted to compensate for the effect of the early thrust reduction. Further, in those tests where the airspeed achieved at the 35-ft. height is slightly less than the V2-5 knots limiting value, it will be permissible, in lieu of conducting the tests again, to analytically adjust the test distance to account for the excessive speed decrement.

(c) All-engines-operating abuse tests.

1 Section 25.107(e)(4) states that there must not be a “marked increase” in the scheduled takeoff distance when reasonably expected service variations such as early and excessive rotation and out-of-trim conditions are encountered. This has been interpreted as requiring takeoff tests with all engines operating with:

(aa) An abuse on rotation speed, and (bb) Out-of-trim conditions, but with rotation at the scheduled VR speed.

NOTE: The expression “marked increase” in the takeoff distance is defined as any amount in excess of one percent of the scheduled takeoff distance. Thus, the abuse tests should not result in field lengths more than 101 percent of the takeoff field lengths calculated in accordance with the applicable requirements of part 25 for presentation in the AFM.

2 For the early rotation abuse condition with all engines operating, and at a weight as near as practicable to the maximum sea level standard day takeoff weight limit, it should be shown by test that when the airplane is over-rotated at a speed below the scheduled VR, no “marked increase” in the scheduled AFM field length will result. For this demonstration, the airplane should be rotated at a speed 7 percent or 10 knots, whichever is less, below the scheduled VR. Tests should be conducted at a rapid rotation rate or should include an

overrotation of 2 degrees above normal attitude after liftoff. Tail strikes during this demonstration are acceptable if they are minor and do not result in unsafe conditions.

3 For reasonably expected out-of-trim conditions with all engines operating and as near as practicable to the maximum weight allowed under sea level standard day conditions, it should be shown that there will not be a “marked increase” in the scheduled AFM takeoff distance when rotation is initiated in a normal manner at the scheduled VR speed. (See paragraph 21b(7)(b) for additional guidance regarding the evaluation of flight characteristics for out-of-trim conditions.) The amount of mis-trim should be the maximum mistrim that would not result in a takeoff configuration warning, including taking into account the takeoff configuration warning system rigging tolerance. It is permissible to accept an analysis in lieu of actual testing if the analysis shows that the out-of-trim condition would not present unsafe flight characteristics or “marked increase” in the scheduled AFM field lengths.

(d) Stall Warning During Takeoff Speed Abuse Tests. The presumption is that if an operational pilot was to make an error in takeoff speeds that resulted in an encounter with stall warning, the likely response would be to recover aggressively to a safe flight condition rather than making a conscious effort to duplicate the AFM takeoff performance data. Therefore, the activation of any stall warning devices, or the occurrence of airframe buffeting during takeoff speed abuse testing, is unacceptable.

(7) Section 25.107(f) - Liftoff Speed (VLOF). The liftoff speed (VLOF) is defined as the calibrated airspeed at which the airplane first becomes airborne (i.e., no contact with the runway). This allows comparison of liftoff speed with tire limit speed. VLOF differs from VMU in that VMU is the minimum possible VLOF speed for a given configuration, and depending upon landing gear design, VMU liftoff is shown to be the point where all of the airplane weight is being supported by airplane lift and thrust forces and not any portion by the landing gear. For example, after the VMU speed is reached, a truck tilt actuator may force a front or rear wheel set to be in contact with the runway, even though the liftoff is in progress by virtue of lift being greater than weight. 11. Accelerate-Stop Distance - § 25.109.

a. Explanation. This section describes test demonstrations and data expansion methods necessary to determine accelerate-stop distances for publication in the FAA AFM, as required by § 25.1583(h) (by reference to § 25.1533). Amendment 25-92 revised some aspects of the part 25 accelerate-stop criteria and added new requirements related to the stopping capability of the airplane as affected by brake wear and wet runways. The changes imparted to the acceleratestop requirements by amendment 25-92 are listed below. (For other material related to the use of accelerate-stop distances, see parts 121 and 135 of the Code of Federal Regulations)

(1) Section 25.101(i) was added to require accelerate-stop distances to be determined with all the airplane wheel brake assemblies at the fully worn limit of their allowable wear range.

(2) Section 25.105(c)(1) was revised to require takeoff data to be determined for wet, in addition to dry, hard surfaced runways. At the applicant’s option, takeoff data may also be determined for wet runways that have grooved or porous friction course surfaces.

(3) Section 25.107(a)(2) was revised to remove the reference to “takeoff decision speed” from the definition of V1.

(4) Section 25.109 was revised to add a requirement to determine accelerate-stop distances for wet runways. Additionally, the requirement for the AFM expansion to include two seconds of continued acceleration beyond V1, with the operating engines at takeoff thrust, as introduced by amendment 25-42, was replaced with a distance increment equivalent to two seconds at V1. Also, the text of § 25.109(a) was modified to clarify that the accelerate-stop distances must take into account the highest speed reached during the rejected takeoff maneuver, including, as applicable, speeds higher than V1.

(5) Section 25.109(f) was added to permit credit for the use of reverse thrust in determining wet runway accelerate-stop distances (subject to the requirements of § 25.109(e)) and to explicitly deny reverse thrust credit for determining dry runway accelerate-stop distances.

(6) Section 25.109(i) was added to require a maximum brake energy accelerate-stop test to be conducted with not more than 10 percent of the allowable brake wear range remaining on each individual wheel-brake assembly.

(7) Section 25.735(h) was added to require the maximum rejected takeoff brake energy absorption capacity rating used during qualification testing to the applicable Technical Standard Order to be based on the fully worn limit of the brake’s allowable wear range.

NOTE: Section 25.735, including § 25.735(h) has been more recently revised by amendment 25-107.

(8) Section 25.1533(a)(3) was revised to add runway surface condition (dry or wet) as a variable that must be accounted for in establishing minimum takeoff distances. Section 25.1533(a)(3) was also revised to allow wet runway takeoff distances on grooved and porous friction course (PFC) runways to be established as additional operating limitations, but approval to use these distances is limited to runways that have been designed, constructed, and maintained in a manner acceptable to the FAA Administrator. b. The applicable part 25 regulations are § 25.109, and the following:

§ 25.101(f) Airplane configuration and procedures

§ 25.101(h) Pilot retarding means time delay allowances

§ 25.101(i) Worn brake stopping performance

§ 25.105 Takeoff configuration and environmental and runway

conditions

§§ 25.107(a)(l) & (2) Defines V1 and VEF speeds

§ 25.735 Brakes

§ 25.1301 Function and installation

§ 25.1309 Equipment, systems, and installation

§ 25.1533 Additional operating limitations - maximum takeoff weights and minimum takeoff distances

§ 25.1583(h) Airplane Flight Manual - operating limitations

§ 25.1587 Airplane Flight Manual - performance information c. Procedures. The following paragraphs provide guidance for accomplishing acceleratestop flight tests and expanding the resulting data for the determination of AFM performance information.

(1) Accelerate-stop testing. The following guidance is applicable to turbine-powered airplanes with and without propellers. Guidance regarding flight testing applies only to dry runway accelerate-stop distances. Guidance for expanding the flight test data to determine AFM distances applies to both dry and wet runways, unless otherwise noted. Further guidance for determining wet runway accelerate-stop distances is provided in paragraph 11c(4).

(a) In order to establish a distance that would be representative of the distance needed in the event of a rejected takeoff, where the first action to stop the airplane is taken at or below V1, a sufficient number of test runs should be conducted for each airplane configuration specified by the applicant. (For intermediate configurations, see paragraph 3 of this AC.)

(b) The guidance outlined in paragraph 11c(3) describes how to include allowances for any time delays, as required by § 25.101(h)(3), for the flightcrew to accomplish the rejected takeoff operating procedures.

(c) Section 25.101(i) states that the accelerate-stop distances must be determined with all the airplane wheel-brake assemblies at the fully worn limit of their allowable wear range. The fully worn limit is defined as the maximum amount of wear allowed before the brake is to be removed from the airplane for overhaul. The allowable wear should be defined in terms of a linear dimension in the axial direction, which is typically determined by measuring the wear pin extension.

1 The only accelerate-stop test that must be conducted at a specific brake wear state is the maximum brake kinetic energy demonstration, which must use brakes that have no more than 10 percent of the allowable brake wear range remaining, as required by § 25.109(i). (See paragraph 11c(2)(c) of this AC). The remainder of the accelerate-stop tests may be conducted with the brakes in any wear state as long as a suitable combination of airplane and dynamometer tests is used to determine the accelerate-stop distances corresponding to fully worn brakes. For example, dynamometer testing may be used to determine whether there is a

reduction in brake performance from the wear state used in the airplane tests to a fully worn brake. The airplane test data could then be adjusted analytically for this difference without additional airplane testing.

2 Either airplane-worn or mechanically-worn brakes (i.e., machined or dynamometer worn) may be used. If mechanically-worn brakes are used, it should be shown that they can be expected to provide similar results to airplane-worn brakes. This comparison can be based on service experience on the test brake or an appropriate equivalent brake, or on dynamometer wear test data when service data are unavailable.

(d) Section 25.109(f)(1) denies credit for the use of reverse thrust as a decelerating means in determining the accelerate-stop distance for a dry runway. This provision applies to both turbine engine and propeller engine reverse thrust. Credit for the additional deceleration available from reverse thrust is permitted for wet runway accelerate-stop distances, provided the thrust reverser system is shown to be safe, reliable, capable of giving repeatable results, and does not require exceptional skill to control the airplane. (See paragraph 11c(4)(e) for guidance related to obtaining accelerate-stop performance credit for reverse thrust on wet runways.)

(e) The accelerate-stop test runs should be conducted at weight/speed combinations that will provide an even distribution of test conditions over the range of weights, speeds, and brake energies for which takeoff data will be provided in the AFM. The effects of different airport elevations can be simulated at one airport elevation, provided the braking speeds employed are relevant for the range of airplane energies to be absorbed by the brakes. The limiting brake energy value in the AFM should not exceed the maximum demonstrated in these tests or the maximum for which the brake has been approved. (See paragraph 11c(2) for further guidance related to tests and analyses for the demonstration of the maximum brake energy absorption capability.)

(f) The V1 speeds used in the accelerate-stop tests need not correspond precisely to the AFM values for the test conditions since it may be necessary to increase or decrease the AFM V1 speed to investigate fully the energy range and weight envelope.

(g) A total of at least six accelerate-stop flight tests should be conducted. Unless sufficient data are available for the specific airplane type showing how braking performance varies with weight, kinetic energy, lift, drag, ground speed, torque limit, etc., at least two tests should be conducted for each configuration when the same braking coefficient of friction is being claimed for multiple aerodynamic configurations. These tests should be conducted on hard surfaced, dry runways.

(h) For approval of dispatch capability with anti-skid inoperative, nose wheel brakes or specified main wheel-brake(s) inoperative, automatic braking systems, etc., a full set of tests, as described in paragraph (g) above, should normally be conducted. A lesser number of tests may be accepted for “equal or better” demonstrations, to establish small increments or if adequate conservatism is used during testing.

(i) Either ground or airborne instrumentation should include means to determine the horizontal distance time-history.

(j) The wind speed and direction relative to the test runway should be determined and corrected to a height corresponding to the approximate height of the mean aerodynamic chord. (See paragraph 3 of this AC.)

(k) The accelerate-stop tests should be conducted in the following configurations:

1 Heavy to light weight as required.

2 Most critical c.g. position.

3 Wing flaps in the takeoff position(s).

4 Tire pressure: before taxi and with cold tires, set to the highest value appropriate to the takeoff weight for which approval is being sought.

5 Engine idle thrust: set at the recommended upper limit for use on the ground or the effect of maximum ground idle thrust may be accounted for in data analyses. For maximum brake energy and fuse plug no-melt tests, data analysis may not be used in place of maximum ground idle thrust.

Continue reading ↓ 120 of 1066 passages shown