AC 25-17A Transport Airplane Cabin Interiors Crashworthiness Handbook
This Advisory Circular (AC) provides acceptable certification methods, but not necessarily the only acceptable methods, for demonstrating compliance with the crashworthiness requirements of part 25, as amended through Amendment 25-112, of Title 14 of the Code of Federal Regulations (14 CFR) for transport category airplanes. The guidance in this AC is not mandatory nor a regulation.
Text read by OCR from a scanned file (30 of 893 pages). Check the original, as some words may be misread.
Change 1 Cover Page
Image of the Department of Transportation logo. U.S. Department of Transportation Federal Aviation Administration
Advisory Circular
Subject: Transport Airplane Cabin Interiors Crashworthiness Handbook
Date: 05/24/16 Initiated By: ANM-115
AC No: 25-17A Change: 1
1. PURPOSE. This change clarifies guidance for the head strike zone, to standardize application of the head strike zone when showing compliance with Title 14, Code of Federal Regulations (14 CFR) 25.785(b) and (d). Protecting the occupant’s head from serious injury requires determination of the zone that the head could strike, i.e., the head strike zone. Because inertial forces will cause the head to travel along the longitudinal axis of the airplane, when applicants show compliance for the inertia forces specified in §§ 25.561 and 25.562, the head strike zone should be oriented in the same direction (the airplane longitudinal axis) as the forces are applied. The guidance in the previous release of this AC did not state this to be the case, so some applicants misinterpreted the head strike direction to be aligned with the seat, regardless of angle of installation of the seat and the inertial forces. This interpretation was not consistent with § 25.785, which protects occupants in the emergency landing conditions specified in §§ 25.561 and 25.562. Additionally, a literal interpretation of the head strike zone depicted in AC 25-17A would include portions of the occupant’s own seat very close to the seat back and seat bottom cushions. This part of the zone is not considered likely to cause serious injury to the occupant’s head and has been removed from the zone.
2. PRINCIPAL CHANGES. Change 1 updates AC 25-17A, Transport Airplane Cabin Interiors Crashworthiness Handbook, dated May 18, 2009. We have added the change number and date of revision at the top of each changed page. We have also marked the changes with a vertical change bar in the margin. Specifically, Change 1 incorporates the following changes:
a. On pages 46, 59, 72, 85, 98, 112, 126, and 140, the definition of the head strike zone is modified to specify the zone is in the direction of the airplane longitudinal axis, and does not include those portions of the occupant’s own seat that are very close to the seat back and seat bottom cushions.
b. On pages 47, 60, 73, 86, 99, 113, 127 and 141, the figure showing the head strike zone is modified to show the zone is in the direction of the airplane longitudinal axis, and does not include those portions of the occupant’s own seat that are very close to the seat back and seat bottom cushions.
05/24/16 AC 25-17A Change 1
Page Control Chart
If you have suggestions for improving this AC, you may use the Advisory Circular Feedback form at the end of this AC.
Michael Kaszycki Acting Manager, Transport Airplane Directorate Aircraft Certification Service
Remove Pages Dated Insert Pages Dated
46 and 47 … 05/18/2009 46 and 47 … 05/24/2016
59 and 60 … 05/18/2009 59 and 60 … 05/24/2016
72 and 23 … 05/18/2009 72 and 23 … 05/24/2016
85 and 86 … 05/18/2009 85 and 86 … 05/24/2016
98 and 99 … 05/18/2009 98 and 99 … 05/24/2016
112 and 113 … 05/18/2009 112 and 113 … 05/24/2016
126 and 127 … 05/18/2009 126 and 127 … 05/24/2016
140 and 141 … 05/18/2009 140 and 141 … 05/24/2016
AC 25-17A Cover Page
Subject: TRANSPORT AIRPLANE CABIN INTERIORS CRASHWORTHINESS HANDBOOK
Date: 5/18/2009 Initiated By: ANM-110
AC No: 25-17A Change:
l. PURPOSE. This Advisory Circular (AC) provides acceptable certification methods, but not necessarily the only acceptable methods, for demonstrating compliance with the crashworthiness requirements of part 25, as amended through Amendment 25-112, of Title 14 of the Code of Federal Regulations (14 CFR) for transport category airplanes. The guidance in this AC is not mandatory nor a regulation.
2. APPLICABILITY.
a. Available guidance pertaining to part 25 is presented according to the amendment level of part 25 to which it applies. For modified airplanes certificated under part 25, the pertinent guidance may be obtained from this AC by reference to the applicable amendment level. (Compliance with later rules may be required in accordance with §§ 21.101(a) and 25.2, or with applicable operating rules as noted above.) Additional guidance may be included in this AC that pertains to either prior amendments or sections that have not been modified. This guidance has been developed to address issues that either have developed since the original issue of this AC, or were inadvertently omitted. The guidance presented in this AC for part 25 airplanes may be used for airplanes certificated under CAR 4b to the extent the rules contained in the older certification bases are the same as those of part 25. The guidance presented herein applies to part 25 through Amendment 25-112.
b. The guidance provided in this document is directed to airplane manufacturers, modifiers, foreign regulatory authorities, and FAA transport airplane type certification engineers, and their designees.
c. This material is neither mandatory nor regulatory in nature and does not constitute a regulation. It describes acceptable means, but not the only means, for demonstrating compliance with the applicable regulations. The FAA will consider other methods of demonstrating compliance that an applicant may elect to present. While these guidelines are not mandatory, they are derived from extensive FAA and industry experience in determining compliance with the relevant regulations. On the other hand, if we become aware of circumstances that convince us that following this AC would not result in compliance with the applicable regulations, we will
ii
not be bound by the terms of this AC, and we may require additional substantiation or design changes as a basis for finding compliance.
d. This material does not change, create any additional, authorize changes in, or permit deviations from, regulatory requirements.
3. CANCELLATION. ADVISORY CIRCULAR 25-17, Transport Airplane Cabin Interiors Crashworthiness Handbook, dated July 15, 1991, is canceled.
4. BACKGROUND.
a. Crashworthiness, as applied to airplane cabin interiors, denotes the incorporation in basic design of considerations pertinent to the protection of airplane occupants in a “survivable crash environment.” A survivable crash environment prevails when the cabin occupants are subjected to crash forces within human tolerance levels, and the structural integrity of the passenger space remains intact such that the occupants can rapidly evacuate the airplane. Structural design for airplane safety has embodied airworthiness and crashworthiness design objectives to varying degrees. Airworthiness design objectives pertain to the ability of the airframe to withstand design loads, or to maintain safety of flight of the airplane relative to the operational environment. Crashworthiness design objectives pertain to safety of the occupants relative to the airplane. Some aspects of crashworthiness, e.g., fuel tank/system design, fuselage deformation and prevention of post-crash fires, are beyond the scope of this AC.
b. Since the inception of federal civil aircraft certification standards, prime emphasis has focused on design for airworthiness, with a preference for application of static load tests, as opposed to dynamic. The emphasis on airworthiness is understandable, since structural and handling deficiencies were inherent in early airplane designs. Further, there was not enough theoretical or technical knowledge available from service experience to generate meaningful design parameters for crash survival. Likewise, in early design, as now, dynamic criteria have been difficult to ascertain. Except for standards for seat belts, seat static load requirements, and exits, crashworthiness was given very little attention until the post-World War II period. During subsequent years, the regulatory process expanded emphasis on crashworthiness. A significant change occurred in 1967, when the Federal Aviation Administration (FAA) promulgated a series of crashworthiness standards affecting transport category airplanes. Further changes were implemented in 1972. As reflected in the rule changes of 1967, the FAA's approach to crashworthiness principally involved three areas of concern: (1) protection of airplane occupants from crash impact; (2) minimizing development and severity of potential crash fire; and (3) rapid evacuation of airplane occupants. Each of these factors has been a focal point in the periodic upgrading of regulatory standards.
c. Part 4b of the former Civil Air Regulations (CAR) was recodified in 1965 as part 25 of 14CFR. The related policy material contained in Civil Aeronautics Manual (CAM) 4b was applicable to part 25 as originally recodified and to current part 25 except in areas that have been amended since recodification. Those policies are included in this AC and listed as guidance applicable to the original recodified version of part 25.
iii
d. This AC consists of the original part 25 of 14 CFR (1965 recodified version), followed by appropriate guidance. Amendments to the regulation are presented in chronological order, with those paragraphs changed by the amendment enclosed within [ ]. The complete regulation text is provided for each amendment. If guidance exists for an amended rule, it is presented following the regulation paragraphs. Guidance from previous amendments to the rule are reprinted for each applicable amendment of the regulation. At the end of the guidance paragraph within ( ) is the amendment level when the guidance was first applicable.
e. Certain changes may require compliance with rules later than the type certification basis. For example:
(1) § 21.101 the change product rule – helps determine when amended and supplemental type certification products need to utilize later amendment levels for areas of change.
(2) § 25.2 special retroactive requirements – requires, in part, that applicants for amended or supplemental type certification projects need to utilize amendment levels which may be later than those in the type certification basis of the airplane when the projects will result in an increase in the maximum seating capacity of the airplanes.
(3) Operating rules §§ 91.58, 121.310, 121.311, 121.312, 121.317, 121.318, 121.319, 125.113, 135.170, and Appendix A of part 135 of the CFR – require, in some cases, that airplanes operating under these parts have materials or equipment installed which are in excess of the type certification basis of the airplanes.
f. Advisory circulars listed in Appendix 3 may be revised after issuance of this AC. The latest available revision of the listed AC should be used.
/s/ Ali Bahrami
Ali Bahrami Manager, Transport Airplane Directorate Aircraft Certification Service,
iv
TABLE OF CONTENTS
Paragraph Page
1 – 10 [RESERVED]
SECTION 25.561 EMERGENCY LANDING CONDITIONS GENERAL
11. Regulation in Effect at Adoption of Part 25. 1 12. Amendment 25-23, Effective May 8, 1970. 2 13. Amendment 25-64, Effective June 16, 1988. 3 14. Amendment 25-91, Effective July 29, 1997. 4 15 – 20. [RESERVED]
Table of Contents
SECTION 25.562 EMERGENCY LANDING DYNAMIC CONDITIONS
21. Section 25.562 Did Not Exist Prior to Amendment 25-64. 7 22. Amendment 25-64, Effective June 16, 1988. 7 23 – 40. [RESERVED]
SECTION 25.772 PILOT COMPARTMENT DOORS
41. Section 25.772 Did Not Exist Prior to Amendment 25-33. 13 42. Amendment 25-33, Effective October 21, 1972. 13 43. Amendment 25-47, Effective December 24, 1979. 13 44. Amendment 25-72, Effective August 20, 1990. 15 45. Amendment 25-106, Effective January 15, 2002. 16 46 - 60. [RESERVED]
SECTION 25.783 DOORS
61. Regulation in Effect at Adoption of Part 25. 19 62. Amendment 25-15, Effective October 24, 1967. 22 63. Amendment 25-23, Effective May 8, 1970. 25 64. Amendment 25-54, Effective October 14, 1980. 28 65. Amendment 25-72, Effective August 20, 1990. 32 66. Amendment 25-88, Effective December 9, 1996. 36 67 - 80. [RESERVED]
SECTION 25.785 SEATS, BERTHS, SAFETY BELTS, AND HARNESSES
81. Regulation in Effect at Adoption of Part 25. 41 82. Amendment 25-15, Effective October 24, 1967. 53
v
83. Amendment 25-20, Effective April 23, 1969. 66 84. Amendment 25-32, Effective May 1, 1972. 79 85. Amendment 25-51, Effective March 6, 1980. 92 86. Amendment 25-64, Effective June 16, 1988. 106 87. Amendment 25-72, Effective August 20, 1990. 120 88. Amendment 25-88, Effective December 9, 1996. 134 89 - 100. [RESERVED]
SECTION 25.787 STOWAGE COMPARTMENTS
101. Regulation in Effect at Adoption of Part 25. 149 102. Amendment 25-32, Effective May 1, 1972. 149 103. Amendment 25-38, Effective February 1, 1977. 152 104. Amendment 25-51, Effective March 6, 1980. 155 105 - 120. [RESERVED]
SECTION 25.789 RETENTION OF ITEMS OF MASS
121. Section 25.789 Did Not Exist Prior To Amendment 25-32. 159 122. Amendment 25-32, Effective May 1, 1972. 159 123. Amendment 25-46, Effective December 1, 1978. 159 124 - 140. [RESERVED]
SECTION 25.791 PASSENGER INFORMATION SIGNS
141. Section 25.791 Did Not Exist Prior to Amendment 25-32. 161 142. Amendment 25-32, Effective May 1, 1972. 161 143. Amendment 25-72, Effective August 20, 1990. 162 144 - 160. [RESERVED]
SECTION 25.793 FLOOR SURFACES
161. Section 25.793 Did Not Exist Prior to Amendment 25-51. 165 162. Amendment 25-51, Effective March 6, 1980. 165 163 - 210. [RESERVED]
SECTION 25.795 SECURITY CONSIDERATIONS
211. Section 25.795 Did Not Exist Prior to Amendment 25-106. 167 212. Amendment 25-106, Effective January 15, 2002. 167 213 - 250. [RESERVED]
vi
SECTION 25.801 DITCHING
251. Regulation in Effect at Adoption of Part 25. 169 252. Amendment 25-72, Effective August 20, 1990. 171 253 - 270. [RESERVED]
SECTION 25.803 EMERGENCY EVACUATION
271. Regulation In Effect At Adoption Of Part 25. 175 272. Amendment 25-1, Effective June 7, 1965. 175 273. Amendment 25-15, Effective October 24, 1967. 176 274. Amendment 25-17, Effective June 20, 1968. 180 275. Amendment 25-20, Effective April 23, 1969. 185 276. Amendment 25-32, Effective May 1, 1972. 190 277. Amendment 25-46, Effective December 1, 1978. 195 278. Amendment 25-72, Effective August 20, 1990. 201 279 - 300. [RESERVED]
SECTION 25.805 FLIGHTCREW EMERGENCY EXITS
301. Amendment 25-72, Effective August 20, 1990. 205 302. Amendment 25-72, Effective August 20, 1990. 205 303 - 320. [RESERVED]
SECTION 25.807 PASSENGER EMERGENCY EXITS
321. Regulation in Effect at Adoption of Part 25. 207 322. Amendment 25-15, Effective October 24, 1967. 211 323. Amendment 25-32, Effective May 1, 1972. 219 324. Amendment 25-39, Effective February 10, 1977. 228 325. Amendment 25-46, Effective February 11, 1978. 236 326. Amendment 25-55, Effective April 26, 1982. 245 327. Amendment 25-67, Effective July 24, 1989. 254 328. Amendment 25-72, Effective August 20, 1990. 263 329. Amendment 25-88, Effective December 9, 1996. 270 330. Amendment 25-94, Effective March 25, 1998. 277 331 - 350. [RESERVED]
SECTION 25.809 EMERGENCY EXIT ARRANGEMENT
351. Regulation in Effect at Adoption of Part 25. 285 352. Amendment 25-1, Effective June 7, 1965. 285 353. Amendment 25-9, Effective June 30, 1966. 290 354. Amendment 25-15, Effective October 24, 1967. 292 355. Amendment 25-32, Effective, May 1, 1972. 296
vii
356. Amendment 25-34, Effective December 31, 1972. 301 357. Amendment 25-46, Effective December 1, 1978. 306 358. Amendment 25-47, Effective December 24, 1979. 312 359. Amendment 25-72, Effective August 20, 1990. 318 360 - 370. [RESERVED]
SECTION 25.810 EMERGENCY EGRESS ASSIST MEANS AND ESCAPE ROUTES
371. Section 25.810 Did Not Exist Prior to Amendment 25-72. 321 372. Amendment 25-72, Effective August 20, 1990. 321 373. Amendment 25-88, Effective December 9, 1996. 326 374 - 380. [RESERVED]
SECTION 25.811 EMERGENCY EXIT MARKING
381. Regulation in Effect at Adoption of Part 25. 333 382. Amendment 25-1, Effective June 7, 1965. 334 383. Amendment 25-15, Effective October 24, 1967. 339 384. Amendment 25-32, Effective May 1, 1972. 344 385. Amendment 25-46, Effective December 1, 1978. 349 386. Amendment 25-79, Effective September 27, 1993. 355 387. Amendment 25-88, Effective December 9, 1996. 360 388 - 390. [RESERVED]
SECTION 25.812 EMERGENCY LIGHTING
391. Section 25.812 Did Not Exist Prior to Amendment 25-15. 365 392. Amendment 25-15, Effective October 24, 1967. 365 393. Amendment 25-28, Effective September 25, 1971. 369 394. Amendment 25-32, Effective May 1, 1972. 373 395. Amendment 25-46, Effective December 1, 1978. 378 396. Amendment 25-58, Effective November 26, 1984. 383 397. Amendment 25-88, Effective December 9, 1996. 389 398 - 410. [RESERVED]
SECTION 25.813 EMERGENCY EXIT ACCESS
411. Regulation in Effect at Adoption of Part 25. 397 412. Amendment 25-1, Effective June 7, 1965. 403 413. Amendment 25-15, Effective October 24, 1967. 409 414. Amendment 25-17, Effective June 20, 1968. 417 415. Amendment 25-32, Effective May 1, 1972. 424 416. Amendment 25-46, Effective December 1, 1978. 432 417. Amendment 25-72, Effective August 20, 1990. 440 418. Amendment 25-76, Effective June 3, 1992. 450
viii
419. Amendment 25-88, Effective December 9, 1996. 461 420 - 440. [RESERVED]
SECTION 25.815 WIDTH OF MAIN AISLE
441. Regulation in Effect at Adoption of Part 25. 473 442. Amendment 25-15, Effective October 24, 1967. 474 443. Amendment 25-38, Effective February 1, 1977. 476 444 - 460. [RESERVED]
SECTION 25.817 MAXIMUM NUMBER OF SEATS ABREAST
461. Section 25.817 Did Not Exist Prior to Amendment 25-15. 479 462. Amendment 25-15, Effective October 24, 1967. 479 463 - 480. [RESERVED]
SECTION 25.819 LOWER DECK SERVICE COMPARTMENTS (INCLUDING GALLEYS)
481. Section 25.819 Did Not Exist Prior to Amendment 25-53. 481 482. Amendment 25-53, Effective August 31, 1980. 481 483. Amendment 25-110, Effective July 21, 2003. 483 484 - 600. [RESERVED]
SECTION 25.851 FIRE EXTINGUISHERS
601. Regulation in Effect at Adoption of Part 25. 487 602. Amendment 25-54, Effective October 14, 1980. 490 603. Amendment 25-72, Effective August 20, 1990. 493 604. Amendment 25-74, Effective May 16, 1991. 497 605 - 620. [RESERVED]
SECTION 25.853 COMPARTMENT INTERIORS
621. Regulation in Effect at Adoption of Part 25. 503 622. Amendment 25-15, Effective October 24, 1967. 508 623. Amendment 25-17, Effective June 20, 1968. 511 624. Amendment 25-23, Effective May 8, 1970. 515 625. Amendment 25-32, Effective May 1, 1972. 519 626. Amendment 25-51, Effective March 6, 1980. 523 627. Amendment 25-59, Effective November 26, 1984. 528 628. Amendment 25-60, Effective June 16, 1986. 532 629. Amendment 25-61, Effective August 20, 1986. 537 630. Amendment 25-66, Effective September 26, 1988. 542 631. Amendment 25-72, Effective August 20, 1990. 548
ix
632. Amendment 25-83, Effective March 6, 1995. 552 633 - 640. [RESERVED]
SECTION 25.854 LAVATORY FIRE PROTECTION
641. Section 25.854 Did Not Exist Prior to Amendment 25-74. 557 642. Amendment 25-74, Effective May 16, 1991. 557 643 - 650. [RESERVED]
SECTION 25.855 CARGO AND BAGGAGE COMPARTMENTS
651. Regulation in Effect at Adoption of Part 25. 559 652. Amendment 25-15, Effective October 24, 1967. 560 653. Amendment 25-32, Effective May 1, 1972. 561 654. Amendment 25-60, Effective June 16, 1986 563 655. Amendment 25-72, Effective August 20, 1990. 565 656. Amendment 25-93, Effective March 19, 1998. 567 657 - 660. [RESERVED]
SECTION 25.856 THERMAL/ACOUSTIC INSULATION MATERIALS
661. Section 25.856 Did Not Exist Prior to Amendment 25-111. 571 662. Amendment 25-111, Effective September 2, 2003. 571 663 - 670. [RESERVED]
SECTION 25.857 CARGO COMPARTMENT CLASSIFICATION
671. Regulation in Effect at Adoption of Part 25. 573 672. Amendment 25-32, Effective May 1, 1972. 576 673. Amendment 25-60, Effective June 16, 1986. 580 674. Amendment 25-93, Effective March 19, 1998. 583 675 - 730. [RESERVED]
SECTION 25.869 FIRE PROTECTION: SYSTEMS
731. Section 25.869 Did Not Exist Prior to Amendment 25-72. 587 732. Amendment 25-72, Effective July 20, 1990. 587 733 - 750. [RESERVED]
SECTION 25.1307 MISCELLANEOUS
751. Regulation in Effect at Adoption of Part 25. 589 752. Amendment 25-23, Effective May 8, 1970. 589
x
753. Amendment 25-46, Effective December 1, 1978. 590 754. Amendment 25-54, Effective October 14, 1980. 591 755. Amendment 25-72, Effective August 20, 1990. 592 756 - 780. [RESERVED]
SECTION 25.1359 ELECTRICAL SYSTEM FIRE AND SMOKE PROTECTION
781. Section 25.1359(d) Did Not Exist Prior to Amendment 25-32. 595 782. Amendment 25-32, Effective May 1, 1972. 595 783. Removed at Amendment 25-72, Effective August 20, 1990. 595 784 - 800. [RESERVED]
SECTION 25.1411 SAFETY EQUIPMENT—GENERAL
801. Regulation in Effect at Adoption of Part 25. 597 802. Amendment 25-32, Effective May 1, 1972. 599 803. Amendment 25-46, Effective December 1, 1978. 601 804. Amendment 25-53, Effective August 31, 1980. 603 805. Amendment 25-70, Effective November 27, 1989. 606 806. Amendment 25-79, Effective September 27, 1993. 608 807 - 820. [RESERVED]
SECTION 25.1413 SAFETY BELTS
821. Regulation in Effect at Adoption of Part 25. 613 822. Amendment 25-44, Effective December 4, 1978. 613 823. Amendment 25-51, Effective March 8, 1980. 614 824. Removed at Amendment 25-72, Effective July 20, 1990. 614 825 - 840. [RESERVED]
SECTION 25.1415 DITCHING EQUIPMENT
841. Regulation in Effect at Adoption of Part 25. 615 842. Amendment 25-29, Effective October 21, 1971. 617 843. Amendment 25-52, Effective September 9, 1980. 619 844. Amendment 25-72, Effective August 20, 1990. 622 845. Amendment 25-82, Effective June 21, 1994. 624 846 - 880. [RESERVED]
SECTION 25.1421 MEGAPHONES
881. Section 25.1421 Did Not Exist Prior to Amendment 25-41. 627 882. Amendment 25-41, Effective September 1, 1977. 627 883 - 900. [RESERVED]
xi
SECTION 25.1423 PUBLIC ADDRESS SYSTEMS
901. Section 25.1423 Did Not Exist Prior to Amendment 25-70. 629 902. Amendment 25-70, Effective November 27, 1989. 629 903. Amendment 25-79, Effective September 27, 1993. 629 904 – 920. [RESERVED]
SECTION 25.1439(a) PROTECTIVE BREATHING EQUIPMENT
921. Regulation in Effect at Adoption of Part 25. 631 922. Amendment 25-38, Effective February 1, 1977.. 631 923 - 970. [RESERVED]
SECTION 25.1447 EQUIPMENT STANDARDS FOR OXYGEN DISPENSING UNITS
971. Regulation in Effect at Adoption of Part 25. 633 972. Amendment 25-41, Effective September 1, 1977. 635 973. Amendment 25-87, Effective July 5, 1996. 637 974 - 1010. [RESERVED]
SECTION 25.1451 FIRE PROTECTION FOR OXYGEN EQUIPMENT
1011. Regulation in Effect at Adoption of Part 25. 641 1012. Removed at Amendment 25-72, Effective August 20, 1990. 641 1013 - 1040. [RESERVED]
SECTION 25.1541 MARKINGS AND PLACARDS—GENERAL
1041. Regulation in Effect at Adoption of Part 25. 643 1042 - 1060. [RESERVED]
SECTION 25.1557(a), (c), and (d) MISCELLANEOUS MARKINGS AND PLACARDS
1061. Regulation in Effect at Adoption of Part 25. 645 1062. Amendment 25-32, Effective May 1, 1972. 645 1063. Amendment 25-38, Effective February 1, 1977. 646 1064. Amendment 25-72, Effective August 20, 1990. 646 1065 - 1100. [RESERVED]
xii
SECTION 25.1561 SAFETY EQUIPMENT
1101. Regulation in Effect at Adoption of Part 25. 647 1102. Amendment 25-46, Effective December 1, 1978. 647 1103 - 1150. [RESERVED]
APPENDIX F TO PART 25 ACCEPTABLE PROCEDURES FOR FLAMMABILITY TESTING FOR COMPLIANCE WITH PART 25 FLAMMABILITY REQUIREMENTS
1151. Appendix F Did Not Exist Prior to Amendment 25-15. 649 1152. Appendix F, Amendment 25-15, Effective October 24, 1967. 649 1153. Appendix F, Amendment 25-32, Effective May 1, 1972. 650 1154. Appendix F, Amendment 25-55, Effective April 26, 1982. 653 1155. [Part I] Amendment 25-59, Effective November 26, 1984. 655 1156. Part I Amendment 25-72, Effective August 20, 1990. 658 1157. Part I Amendment 25-111, Effective September 2, 2003. 662 1158 - 1161. [RESERVED]
1162. Appendix F, Part II, Did Not Exist Prior to Amendment 25-59. 667 1163. Part II Amendment 25-59, Effective November 26, 1984. 667 1164. Part II Amendment 25-72, Effective August 20, 1990. 677 1165. Part II Amendment 25-94, Effective March 25, 1998. 685 1166 - 1170. [RESERVED]
1171. Appendix F, Part III, Did Not Exist Prior to Amendment 25-60. 693 1172. Amendment 25-60, Effective June 16, 1986. 693 1173 - 1177. [RESERVED]
1178. Appendix F, Part IV, Did Not Exist Prior to Amendment 25-61. 701 1179. Part IV Amendment 25-61, Effective August 20, 1986. 701 1180. Part IV Amendment 25-66, Effective September 26, 1988. 715 1181 - 1185. [RESERVED]
1186. Appendix F, Part V, Did Not Exist Prior to Amendment 25-66. 727 1187. Part V Amendment 25-66, Effective September 26, 1988. 727 1188 - 1192. [RESERVED]
1193. Appendix F, Part VI, Did Not Exist Prior to Amendment 25-111. 729 1194. Amendment 25-111, Effective September 2, 2003. 729 1195 - 1200. [RESERVED]
xiii
1201. Appendix F, Part VII, Did Not Exist Prior to Amendment 25-111. 743 1202. Appendix F, Amendment 25-111, Effective September 2, 2003. 743 1203 - 1207. [RESERVED]
APPENDIX J TO PART 25—EMERGENCY EVACUATION
1208. Appendix J Did Not Exist at Prior to Amendment 25-72. 759 1209. Appendix J, Amendment 25-72, Effective August 20, 1990. 759 1210. Appendix J, Amendment 25-79, Effective September 27, 1993. 761 1211 - 1300. [RESERVED]
Appendix 1. CROSS REFERENCE FOR PART 25 AT AMENDMENT 25-0 765 AND CAM 4b
Appendix 2. SYMBOLIC REGULATORY MESSAGES 767
Appendix 3. CRASHWORTHINESS ADVISORY CIRCULARS 773
Appendix 4. TEST PROCEDURES FOR EVALUATING NONSTANDARD 777 EXITS FOR TRANSPORT CATEGORY AIRPLANES
Appendix 5. CRASHWORTHINESS TECHNICAL STANDARD ORDERS 781
Appendix 6. INTERIOR COMPLIANCE CHECKLIST- EXAMPLE 783
Appendix 7. AMENDMENT BY AMENDMENT HISTORY OF 793 CRASHWORTHINESS REQUIREMENTS
Appendix 8. FIRE CONTAINMENT TEST METHODS 805
Appendix 9. ACRONYMS 813
Appendix 10. CROSS REFERENCE FOR PRE-AMENDMENT 25-72 AND 815 POST AMENDMENT 25-72
Appendix 11. FAA MEMORANDUM, 01-115-11, ORIGINAL RELEASE: 819 DATED NOVEMBER 6, 2001, LATEST REVISION, SUBJECT: CERTIFICATION OF STRENGTHENED FLIGHTDECK DOORS ON TRANSPORT CATEGORY AIRPLANES
Appendix 12. ESTABLISHING THE MAXIMUM PASSENGER SEATING 841 CAPACITY FOR AN AIRPLANE MODEL
xiv
Appendix 13. FAA POLICY MEMO ANM-03-115-31, “POLICY 845 STATEMENT ON CONDUCTING COMPONENT LEVEL TESTS TO DEMONSTRATE COMPLIANCE WITH §§ 25.785(B) AND (D)” DATED MAY 9, 2005
Appendix 14. FAA POLICY MEMO ANM-115-05-001, “POLICY 867 STATEMENT ON THE INSTALLATION OF “NO STOWAGE” PLACARDS ON SURFACES NOT DESIGNED OR INTENDED TO BE USED FOR STOWAGE
Appendix 15. FIGURES SHOWING REQUIRED AISLES, CROSS AISLES, 873 AND PASSAGEWAYS FOR TYPE A AND B EXITS
25.561 › Amendment 25-0
SECTION 25.561 EMERGENCY LANDING CONDITIONS GENERAL
11. REGULATION IN EFFECT AT ADOPTION OF PART 25.
a. Regulation.
(a) The airplane, although it may be damaged in emergency landing conditions on land or water, must be designed as prescribed in this section to protect each occupant under those conditions.
(b) The structure must be designed to give each occupant every reasonable chance of escaping serious injury in a minor crash landing when-
(1) Proper use is made of seats, belts, and all other safety design provisions;
(2) The wheels are retracted (where applicable); and
(3) The occupant experiences the following ultimate inertia forces relative to the surrounding structure:
(i) Upward-2.0 g.
(ii) Forward-9.0 g.
(iii) Sideward-1.5 g.
(iv) Downward-4.5 g, or any lesser force that will not be exceeded when the airplane absorbs the landing loads resulting from impact with an ultimate descent velocity of five f.p.s. at design landing weight.
(c) The supporting structure must be designed to restrain, under all loads up to those specified in paragraph (b) (3) of this section, each item of mass that could injure an occupant if it came loose in a minor crash landing.
b. Guidance. Paragraph (b). When testing a seat to demonstrate compliance with the static requirements of § 25.561, the testing should be conducted with an occupant center of gravity (CG) location as defined in NAS 809 (referenced in Technical Standard Order (TSO) C39) and AS8049 (referenced in the current version of TSO-C127). This CG location should be utilized in any airplane interface load analysis conducted. (Amendment 25-0)
25.561 › Amendment 25-23
12. AMENDMENT 25-23, Effective May 8, 1970.
a. Regulation.
(a) The airplane, although it may be damaged in emergency landing conditions on land or water, must be designed as prescribed in this section to protect each occupant under those conditions.
(b) The structure must be designed to give each occupant every reasonable chance of escaping serious injury in a minor crash landing when—
(1) Proper use is made of seats, belts, and all other safety design provisions;
(2) The wheels are retracted (where applicable); and
(3) The occupant experiences the following ultimate inertia forces [acting separately] relative to the surrounding structure:
(i) Upward-2.0g.
(ii) Forward-9.0g.
(iii) Sideward-1.5g .
(iv) Downward-4.5g, or any lesser force that will not be exceeded when the airplane absorbs the landing loads resulting from impact with an ultimate descent velocity of five f.p.s. at design landing weight.
(c) The supporting structure must be designed to restrain, under all loads up to those specified in paragraph (b)(3) of this section, each item of mass that could injure an occupant if it came loose in a minor crash landing.
b. Guidance. Paragraph (b). When testing a seat to demonstrate compliance with the static requirements of § 25.561, the testing should be conducted with an occupant center of gravity (CG) location as defined in NAS 809 (referenced in Technical Standard Order (TSO) C39) and AS8049 (referenced in the current version of TSO-C127). This CG location should be utilized in any airplane interface load analysis conducted. (Amendment 25-0)
25.561 › Amendment 25-64
13. AMENDMENT 25-64, Effective June 16, 1988.
a. Regulation.
(a) The airplane, although it may be damaged in emergency landing conditions on land or water, must be designed as prescribed in this section to protect each occupant under those conditions.
(b) The structure must be designed to give each occupant every reasonable change of escaping serious injury in a minor crash landing when—
(1) Proper use is made of seats, belts, and all other safety design provisions;
(2) The wheels are retracted (where applicable); and
(3) The occupant experiences the following ultimate inertia forces acting separately relative to the surrounding structure:
(i) [Upward, 3.0g.]
(ii) Forward, 9.0g.
(iii) [Sideward, 3.0g on the airframe; and 4.0g on the seats and their attachments.
(iv) Downward, 6.0g.
(v) Rearward, 1.5g]
(c) The supporting structure must be designed to restrain, under all loads up to those specified in paragraph (b)(3) of this section, each item of mass that could injure an occupant if it came loose in a minor crash landing.
[(d) Seats and items of mass (and their supporting structure) must not deform under any loads up to those specified in paragraph (b)(3) of this section in any manner that would impede subsequent rapid evacuation of occupants.]
b. Guidance.
(1) Paragraph (b). When testing a seat to demonstrate compliance with the static requirements of § 25.561, the testing should be conducted with an occupant center of gravity (CG) location as defined in NAS 809 (referenced in Technical Standard Order (TSO) C39) and AS8049 (referenced in the current version of TSO-C127). This CG location should be utilized in any airplane interface load analysis conducted. (Amendment 25-0)
(2) Paragraph (d). The permanent deformations of items of mass, such as galleys and closets, located near exits should not interfere with the opening of those exits. Also, shared
25.561 › Amendment 25-91
loading (loads imposed by the deformation of one furnishing onto an adjacent furnishing) between adjacent items of mass should be considered when determining maximum deformations. Refer to AC 25.562-1B “Dynamic Evaluation of Seat Restraint Systems & Occupant Protection on Transport Airplanes,” dated 1/19/96, Appendix 2 for policy concerning seat deformations for both §§ 25.561(d) and 25.562(c)(8). For § 25.561(d) only the forward, rearward, and sideward deformations are applicable. Deformations and possible load sharing between articles need only be considered for a common load case (e.g., 9g to 9g & 16g to 16g). The dynamic deflections of seats in particular do not have to be considered in conjunction with the static deflections of other articles when assessing possible load sharing. That is, when a seat substantiated under § 25.562 has interaction with another article substantiated under § 25.561, the assessment of load sharing is done using the § 25.561 deflections/reactions for both articles. (Amendment 25-64)
14. AMENDMENT 25-91, Effective July 29, 1997.
a. Regulation.
(a) The airplane, although it may be damaged in emergency landing conditions on land or water, must be designed as prescribed in this section to protect each occupant under those conditions.
(b) The structure must be designed to give each occupant every reasonable chance of escaping serious injury in a minor crash landing when-
(1) Proper use is made of seats, belts, and all other safety design provisions;
(2) The wheels are retracted (where applicable); and
(3) The occupant experiences the following ultimate inertia forces relative to the surrounding structure:
(i) Upward, 3.0g.
(ii) Forward, 9.0g.
(iii) Sideward, 3.0g on the airframe; and 4.0g on the seats and their attachments.
(iv) Downward, 6.0g.
(v) Rearward, 1.5g.
[(c) For equipment, cargo in the passenger compartments and any other large masses, the following apply:
(1) Except as provided in paragraph (c)(2) of this section, these items must be positioned so that if they break loose, they will be unlikely to:
(i) Cause direct injury to occupants;
(ii) Penetrate fuel tanks or lines or cause fire or explosion hazard by damage to adjacent systems; or
(iii) Nullify any of the escape facilities provided for use after an emergency landing.
(2) When such positioning is not practical (e.g. fuselage mounted engines or auxiliary power units) each such item of mass shall be restrained under all loads up to those specified in paragraph (b)(3) of this section. The local attachments for these items should be designed to withstand 1.33 times the specified loads if these items are subject to severe wear and tear through frequent removal (e.g. quick change interior items).]
(d) Seats and items of mass (and their supporting structure) must not deform under any loads up to those specified in paragraph (b)(3) of this section in any manner that would impede subsequent rapid evacuation of occupants.
b. Guidance.
(1) Paragraph (b). When testing a seat to demonstrate compliance with the static requirements of § 25.561, the testing should be conducted with an occupant center of gravity (CG) location as defined in NAS 809 (referenced in Technical Standard Order (TSO) C39) and AS8049 (referenced in the current version of TSO-C127). This CG location should be utilized in any airplane interface load analysis conducted. (Amendment 25-0)
(2) Paragraph (d). The permanent deformations of items of mass, such as galleys and closets, located near exits should not interfere with the opening of those exits. Also, shared loading (loads imposed by the deformation of one furnishing onto an adjacent furnishing) between adjacent items of mass should be considered when determining maximum deformations. Refer to AC 25.562-1B dated 1/10/2006, Appendix 2 for policy concerning seat deformations for both §§ 25.561(d) and 25.562(c)(8). For § 25.561(d) only the forward, rearward, and sideward deformations are applicable. Deformations and possible load sharing between articles need only be considered for a common load case (e.g., 9g to 9g & 16g to 16g) . The dynamic deflections of seats in particular do not have to be considered in conjunction with the static deflections of other articles when assessing possible load sharing. That is, when a seat substantiated under § 25.562 has interaction with another article substantiated under § 25.561, the assessment of load sharing is done using the § 25.561 deflections/reactions for both articles. (Amendment 25-64)
15 – 20. [RESERVED]
THIS PAGE INTENTIONALLY LEFT BLANK
SECTION 25.562 EMERGENCY LANDING DYNAMIC CONDITIONS
21. Section 25.562 Did Not Exist Prior to Amendment 25-64.
22. AMENDMENT 25-64, Effective June 16, 1988.
a. Regulation.
(a) The seat and restraint system in the airplane must be designed as prescribed in this section to protect each occupant during an emergency landing condition when-
25.500 Series › 25.562
(1) Proper use is made of seats, safety belts, and shoulder harnesses provided for in the design; and
(2) The occupant is exposed to loads resulting from the conditions prescribed in this section.
(b) Each seat type design approved for crew or passenger occupancy during takeoff and landing must successfully complete dynamic tests or be demonstrated by rational analysis based on dynamic tests of a similar type seat, in accordance with each of the following emergency landing conditions. The tests must be conducted with an occupant simulated by a 170-pound anthropomorphic test dummy, as defined by 49 CFR Part 572, Subpart B, or its equivalent, sitting in the normal upright position.
(1) A change In downward vertical velocity (∆V) of not less than 35 feet per second, with the airplane's longitudinal axis canted downward 30 degrees with respect to the horizontal plane and with the wings level. Peak floor deceleration must occur in not more than 0.08 seconds after impact and must reach a minimum of 14g.
(2) A change in forward longitudinal velocity (∆V) of not less than 44 feet per second, with the airplane's longitudinal axis horizontal and yawed 10 degrees either right or left, whichever would cause the greatest likelihood of the upper torso restraint system (where installed) moving off the occupant's shoulder, and with the wings level. Peak floor deceleration must occur in not more than 0.09 seconds after impact and must reach a minimum of 16g. Where floor rails or floor fittings are used to attach the seating devices to the test fixture, the rails or fittings must be misaligned with respect to the adjacent set of rails or fittings by at least 10 degrees vertically (i.e., out of Parallel) with one rolled 10 degrees.
(c) The following performance measures must not be exceeded during the dynamic tests conducted in accordance with paragraph (b) of this section:
(1) Where upper torso straps are used for crewmembers, tension loads in individual straps must not exceed 1,750 pounds. If dual straps are used for restraining the upper torso, the total strap tension loads must not exceed 2,000 pounds.
(2) The maximum compressive load measured between the pelvis and the lumbar column of the anthropomorphic dummy must not exceed 1,500 pounds.
(3) The upper torso restraint straps (where installed) must remain on the occupant's shoulder during the impact.
(4) The lap safety belt must remain on the occupant's pelvis during the impact.
(5) Each occupant must be protected from serious head injury under the conditions prescribed in paragraph (b) of this section. Where head contact with seats or other structure can occur, protection must be provided so that the head impact does not exceed a Head Injury Criterion (HIC) of 1,000 units. The level of HIC is defined by the equation:
Where:
t1 is the initial integration time, t2 is the final integration time, and a(t) is the total acceleration vs. time-curve for the head strike, and where
(t) is in seconds, and (a) is in units of gravity (g).
(6) Where leg injuries may result from contact with seats or other structure, protection must be provided to prevent axially compressive loads exceeding 2,250 pounds in each femur.
(7) The seat must remain attached at all points of attachment, although the structure may have yielded.
(8) Seats must not yield under the tests specified in paragraphs (b)(1) and (b)(2) of this section to the extent they would impede rapid evacuation of the airplane occupants.
b. Guidance.
(1) Refer to AC 25.562-1B, “Dynamic Evaluation of Seat Restraint Systems & Occupant Protection on Transport Airplanes,” dated 1/10/2006. (Amendment 25-64)
HIC = (t - t ) [ 1 (t - t )
t
t
a(t) dt ] [ 2 1 2 1 1
2 2.5 ∫ ]max
(2) Paragraph (c)(5). The FAA issued policy memorandum ANM-03-115-28, dated October 2, 2003, and titled “Policy Statement on Use of Surrogate Parts When Evaluating Seatbacks and Seatback Mounted Accessories for Compliance with §§ 25.562(c)(5) and 25.785(b) and (d). This policy may be used with any test method used to demonstrate compliance with blunt force trauma for items mounted on the seatback. The new policy may be used for demonstrating compliance with § 25.562(c)(5), Amendment 25-64, and is provided below. (Amendment 25-64)
(i) The FAA has determined that it is acceptable to use a surrogate test article made of 6061-T4 aluminum which meets the criteria below in lieu of an accessory for demonstrating compliance with §§ 25.562(c)(5) and 25.785(b) and (d) for blunt trauma assessments. An exception to the use of the surrogate test article occurs when the accessory is more rigid (deflects less and absorbs less energy during impact) than the plate defined in this memorandum. In that case, the accessory should be used in the test(s) and not a surrogate test article. The following criteria are applicable when using a surrogate test article during blunt trauma testing in accordance with §§ 25.562(c)(5) and 25.785(b) and (d): (Amendment 25-64)
(A) The surrogate part should be fabricated from 6061-T4 aluminum and have a minimum thickness of 0.238-inch (i.e., 0.25-inch minus a 0.012-inch manufacturing tolerance) at all locations. The length and width of the surrogate part should equal, within tolerances, the length and width of the actual part, respectively. (Amendment 25-64)
(B) The exposed surface of the surrogate part that will be impacted should be flat. That is, it is not required to have the contour of the accessory’s exposed surface represented by the surrogate part. Note that this is based on typical accessory installations, which are essentially mounted flush with the seatback and have a generally homogeneous contact area. Small variations in the surface due to the contour of plastic parts may be ignored. Designs that differ from this (e.g., a design with an exposed structural protrusion) might require the exposed surface of the actual part to be represented in order to adequately assess head injury potential. (Amendment 25-64)
(C) The weight of the surrogate part, and additional ballast if needed, should be ±10 percent of the weight of the actual part. (Amendment 25-64)
(D) The surrogate part should be located on the seatback in the same place (i.e., within manufacturing tolerances for mounting the actual part) where the actual part would be located in terms of the x and y coordinates in Figure 22-1. The surrogate part should be located such that the surface, which will be contacted during the test, is at the same location (i.e., within manufacturing tolerances for mounting the actual part) where the actual part would be in terms of the z coordinate (refer to figure 22-1). (Amendment 25-64)
(E) The surrogate part should be attached to the seat by the final production hardware or a conservative representation of the final production hardware. For substantiating blunt trauma requirements, a conservative representation of the attachment hardware would be at least as rigid as the actual hardware. The surrogate part should be mounted so that it would not move farther or faster, with respect to the seatback, than the actual part during the test. Note that
a conservative representation of the attachment hardware for determining HIC may not adequately represent the attachment hardware for substantiating it to § 25.562 loads. However, if the attachment hardware is adequately represented for substantiating it to § 25.562 loads, the test using a surrogate part may also be used to demonstrate that the attachment hardware will retain the actual accessory under § 25.562 loads. (Amendment 25-64)
(F) If the surrogate part cracks during a test, the test results are invalid. (Amendment 25-64)
(G) A surrogate part made of a material and thickness other than 6061-T4 aluminum in a nominal thickness of 0.25-inch may be used if an FAA Aircraft Certification Office finds that it is at least as rigid (i.e., it deflects less and absorbs less energy during the test). Surrogate test articles which are less rigid than the aluminum surrogate part defined above are not addressed in this AC. If an applicant desires to use a surrogate part which is less rigid, its use should be approved through the issue paper process (or equivalent) or by an FAA policy memorandum. Testing may be required to determine the acceptability of these less rigid surrogate parts. (Amendment 25-64)
FIGURE 22-1 SURROGATE PART INSTALLED ON SEATBACK
23 – 40. [RESERVED]
THIS PAGE INTENTIONALLY LEFT BLANK
25.772 › Amendment 25-47
SECTION 25.772 PILOT COMPARTMENT DOORS
41. Section 25.772 Did Not Exist Prior to Amendment 25-33.
42. AMENDMENT 25-33, Effective October 21, 1972.
a. Regulation.
(a) Except as provided in paragraph (b) of this section, if a lockable door is installed between the pilot compartment and the passenger compartment to comply with § 121.313(f) of this chapter, the emergency exit configuration of the airplane must be designed so that neither crewmembers nor passengers need use that door in order to reach the emergency exits provided for them.
(b) The provisions of paragraph (a) of this section do not apply to an airplane that-
(l) Has a maximum passenger seating configuration of 20 seats or less; or
(2) Is excepted from the equipment requirements of § 121.313(f) under the provisions of § 121.583(a) of this chapter.
b. Guidance. There is no guidance for this regulation.
43. AMENDMENT 25-47, Effective December 24, 1979.
a. Regulation.
(a) Except as provided in paragraph (b) of this section, if a lockable door is installed between the pilot compartment and the passenger compartment to comply with § 121.313(f) of this chapter, the emergency exit configuration of the airplane must be designed so that neither crewmembers nor passengers need use that door in order to reach the emergency exits provided for them. [However, for passenger configuration, means must be provided to enable flight crewmembers to directly enter the passenger compartment from the pilot compartment if the cockpit door becomes jammed.]
(b) The provisions of paragraph (a) of this section do not apply to an airplane that-
(1) Has a maximum passenger seating configuration of 20 seats or less; or
(2) Is excepted from the equipment requirements of § 121.313(f) under the provisions of § 121.583(a) of this chapter.
b. Guidance.
(1) Paragraph (a). Compliance may be shown by either analysis or demonstration. (Amendment 25-47)
(2) Paragraph (a). Acceptance of frangible doors. The following test procedure is acceptable to demonstrate that the door between the pilot compartment and the passenger compartment will not block the flight crewmembers' escape in the event the door is jammed. An acceptable means of showing compliance is by demonstrating that the door is frangible and the flightcrew participants can rapidly egress from the pilot compartment without assistance. (Amendment 25-47)
(i) The test should be conducted in an airplane, or a mockup if the mockup conforms to the production airplane's interior configuration. If a mockup is used, it should include the observer's seat(s), if they are part of the type design, and the bulkhead and door to be tested. The door should be blocked to simulate possible jamming from the top, bottom, and sides (closing and locking alone may not be adequate to simulate all possible jamming). If the fragments from the broken door could cause an obstruction to the escape routes for passenger emergency egress, and if an emergency evacuation demonstration is required by airworthiness regulations or operating rules, consideration should be given to include the passengers in the test. For emergency evacuation demonstrations with passengers, refer to § 25.803(c), Amendment 25- 15. (Amendment 25-47)
(ii) Two participants representing a pilot in the left crew seat and a copilot in the right crew seat should be used for the test. They should be persons with no special escape abilities. The crewmembers should be a female approximately 60-inches tall and weighing no more than 102 lbs and a male approximately 74-inches tall and weighing no less than 210 lbs. The foregoing statures and weights represent the 5th percentile female to 95th percentile male occupants respectively. The female participant will be instructed to break the door and be the first person to egress without assistance from the male participant. Instructions for enhancing the egress should be limited to those instructions that will be provided in the FAA-approved Airplane Flight Manual (AFM) or on the related placards. (Amendment 25-47)
(iii) The test should be conducted in night conditions. If conducted in a hangar during the day, the hangar should be draped and taped so that all sunlight is prevented from entering the hangar. Similar conditions should exist if conducted at night either in or out of a hangar. Lighting may be allowed at ground level to aid in leaving the area near the airplane providing the lighting is kept low and shielded so it does not aid evacuating the airplane. Use of emergency lighting is acceptable. (Amendment 25-47)
(iv) Personnel participating should be informed of the purpose of the demonstration and of the safety precautions. Safety of participants is the responsibility of the applicant, and should be considered to prevent injuries to the participants without compromising the test results. Participants may wear protective gear such as crash helmets, but the protective gear, tools, or any other device should not be used to break through the door. (Amendment 25-47)
25.772 › Amendment 25-72
44. AMENDMENT 25-72, Effective August 20, 1990.
a. Regulation.
[For an airplane that has a maximum passenger seating configuration of more than 20 seats and that has a lockable door installed between the pilot compartment and the passenger compartment:
(a) The emergency exit configuration must be designed so that neither crewmembers nor passengers need use that door in order to reach the emergency exits provided for them; and
(b) Means must be provided to enable flight crewmembers to directly enter the passenger compartment from the pilot compartment if the cockpit door becomes jammed.]
b. Guidance.
(1) Paragraph (b). Compliance may be shown by either analysis or demonstration. (Amendment 25-47)
(2) Paragraph (b). Acceptance of frangible doors. The following test procedure is acceptable to demonstrate that the door between the pilot compartment and the passenger compartment will not block the flight crewmembers' escape in the event the door is jammed. An acceptable means of showing compliance is by demonstrating that the door is frangible and the flightcrew participants can rapidly egress from the pilot compartment without assistance. (Amendment 25-47)
(i) The test should be conducted in an airplane, or a mockup if the mockup conforms to the production airplane's interior configuration. If a mockup is used, it should include the observer's seat(s), if they are part of the type design, and the bulkhead and door to be tested. The door should be blocked to simulate possible jamming from the top, bottom, and sides (closing and locking alone may not be adequate to simulate all possible jamming). If the fragments from the broken door could cause an obstruction to the escape routes for passenger emergency egress, and if an emergency evacuation demonstration is required by airworthiness regulations or operating rules, consideration should be given to include the passengers in the test. For emergency evacuation demonstrations with passengers, refer to § 25.803(c), Amendment 25- 15. (Amendment 25-47)
(ii) Two participants representing a pilot in the left crew seat and a copilot in the right crew seat should be used for the test. They should be persons with no special escape abilities. The crewmembers should be a female approximately 60-inches tall and weighing no more than 102 lbs and a male approximately 74-inches tall and weighing no less than 210 lbs. The foregoing statures and weights represent the 5th percentile female to 95th percentile male occupants respectively. The female participant will be instructed to break the door and be the first person to egress without assistance from the male participant. Instructions for enhancing the
25.772 › Amendment 25-106
egress should be limited to those instructions that will be provided in the FAA-approved Airplane Flight Manual (AFM) or on the related placards. (Amendment 25-47)
(iii) The test should be conducted in night conditions. If conducted in a hangar during the day, the hangar should be draped and taped so that all sunlight is prevented from entering the hangar. Similar conditions should exist if conducted at night either in or out of a hangar. Lighting may be allowed at ground level to aid in leaving the area near the airplane providing the lighting is kept low and shielded so it does not aid evacuating the airplane. Use of emergency lighting is acceptable. (Amendment 25-47)
(iv) Personnel participating should be informed of the purpose of the demonstration and of the safety precautions. Safety of participants is the responsibility of the applicant, and should be considered to prevent injuries to the participants without compromising the test results. Participants may wear protective gear such as crash helmets, but the protective gear, tools, or any other device should not be used to break through the door. (Amendment 25-47)
45. AMENDMENT 25-106, Effective January 15, 2002.
a. Regulation.
For an airplane that has a [lockable door installed between the pilot compartment and the passenger compartment:
(a) For airplanes with a maximum passenger seating configuration of more than 20 seats, the emergency exit configuration must be designed so that neither crewmembers nor passengers require use of the flightdeck door in order to reach the emergency exits provided for them;]
(b) Means must be provided to enable flight crewmembers to directly enter the passenger compartment from the pilot compartment if the cockpit door becomes jammed.
[(c) There must be an emergency means to enable a flight attendant to enter the pilot compartment in the event that the flightcrew becomes incapacitated.]
b. Guidance.
(1) Paragraph (b). Compliance may be shown by either analysis or demonstration. (Amendment 25-47)
(2) Paragraph (b). Acceptance of frangible doors. The following test procedure is acceptable to demonstrate that the door between the pilot compartment and the passenger compartment will not block the flight crewmembers' escape in the event the door is jammed. An acceptable means of showing compliance is by demonstrating that the door is frangible and the
flightcrew participants can rapidly egress from the pilot compartment without assistance. (Amendment 25-47)
(i) The test should be conducted in an airplane, or a mockup if the mockup conforms to the production airplane's interior configuration. If a mockup is used, it should include the observer's seat(s), if they are part of the type design, and the bulkhead and door to be tested. The door should be blocked to simulate possible jamming from the top, bottom, and sides (closing and locking alone may not be adequate to simulate all possible jamming). If the fragments from the broken door could cause an obstruction to the escape routes for passenger emergency egress, and if an emergency evacuation demonstration is required by airworthiness regulations or operating rules, consideration should be given to include the passengers in the test. For emergency evacuation demonstrations with passengers, refer to § 25.803(c), Amendment 25- 15. (Amendment 25-47)
(ii) Two participants representing a pilot in the left crew seat and a copilot in the right crew seat should be used for the test. They should be persons with no special escape abilities. The crewmembers should be a female approximately 60-inches tall and weighing no more than 102 lbs and a male approximately 74-inches tall and weighing no less than 210 lbs. The foregoing statures and weights represent the 5th percentile female to 95th percentile male occupants respectively. The female participant will be instructed to break the door and be the first person to egress without assistance from the male participant. Instructions for enhancing the egress should be limited to those instructions that will be provided in the FAA-approved Airplane Flight Manual (AFM) or on the related placards. (Amendment 25-47)
(iii) The test should be conducted in night conditions. If conducted in a hangar during the day, the hangar should be draped and taped so that all sunlight is prevented from entering the hangar. Similar conditions should exist if conducted at night either in or out of a hangar. Lighting may be allowed at ground level to aid in leaving the area near the airplane providing the lighting is kept low and shielded so it does not aid evacuating the airplane. Use of emergency lighting is acceptable. (Amendment 25-47)
(iv) Personnel participating should be informed of the purpose of the demonstration and of the safety precautions. Safety of participants is the responsibility of the applicant, and should be considered to prevent injuries to the participants without compromising the test results. Participants may wear protective gear such as crash helmets, but the protective gear, tools, or any other device should not be used to break through the door. (Amendment 25-47)
(3) Paragraph (c). Refer to Appendix 11, FAA Memorandum, 01-115-11, Original Release: dated November 6, 2001, Revised December 3, 2002, “Subject: Certification of Strengthened Flightdeck Doors on Transport Category Airplanes.” This policy memorandum outlines acceptable means of compliance with this paragraph and many other regulatory requirements that were affected by Amendment 25-106. (Amendment 25-106)
46 - 60. [RESERVED]
THIS PAGE INTENTIONALLY LEFT BLANK
25.783 › Amendment 25-0
SECTION 25.783 DOORS
61. REGULATION IN EFFECT AT ADOPTION OF PART 25.
a. Regulation.
(a) Each cabin must have at least one easily accessible external door.
(b) There must be a means to lock and safeguard each external door against opening in flight (either inadvertently by persons or as a result of mechanical failure). Each external door must be openable from both the inside and the outside, even though persons may be crowded against the door on the inside of the airplane. Inward opening doors may be used if there are means to prevent occupants from crowding against the door to an extent that would interfere with the opening of the door. The means of opening must be simple and obvious and must be arranged and marked so that it can be readily located and operated, even in darkness. Auxiliary locking devices may be used.
(c) Each external door must be reasonably free from jamming as a result of fuselage deformation in a minor crash.
(d) Each external door must be located where persons using them will not be endangered by the propellers when appropriate operating procedures are used.
(e) There must be a provision for direct visual inspection of the locking mechanism by crewmembers to determine whether external doors, for which the initial opening movement is outward (including passenger, crew, service, and cargo doors), are fully locked. In addition, there must be a visual means to signal to appropriate crewmembers when normally used external doors are closed and fully locked.
(f) Cargo and service doors not suitable for use as an exit in an emergency need only meet paragraph (e) of this section and be safeguarded against opening in flight as a result of mechanical failure.
b. Guidance.
(l) Paragraphs (b) through (e). The requirements of these paragraphs apply to all cabin and pilot compartment external doors usable for entrance or egress. It is not restricted to the main cabin door. Cargo and service doors not suitable for emergency egress need only comply with § 25.783(e) and be safeguarded against opening in flight as a result of mechanical failure. (Amendment 25-0)
(2) Paragraph (b). Auxiliary locking devices. (Amendment 25-0)
(i) The use of auxiliary locking devices is permitted. Such devices would include dual locking handles, other types of locking and safety devices, two position handles, and dual operation handles (where one operation such as pushing or pulling on the handle unlocks the latching mechanism and the second operation of turning the handle unlatches the door for opening). Auxiliary locking devices should be used only as an additional safety factor and should not be used as a means of correcting an inadequate design of the primary locking or latching means. The advantages to be gained from the installation of auxiliary or dual locking devices (safety chains and dual handle main locking means) should be weighed against the need to easily and rapidly open the door in case of emergencies so that the overall level of safety is as high as practicable. (Amendment 25-0)
(ii) All locking or safety means, including safety chains and latches of any kind, should be so positioned and designed that their presence, location and means of operation are obvious to one not familiar with door designs. (Amendment 25-0)
(A) The means of fastening safety devices should be sufficiently simple to make removal easy. (Amendment 25-0)
(B) Any emergency release mechanism installed to release the safety device should operate with a simple motion and upon the application of relatively small forces. (Amendment 25-0)
(C) All locking devices should be readily operable from both inside and outside of the airplane and be appropriately marked both inside and outside. (Amendment 25-0)
(iii) Auxiliary safety devices meeting the standards of paragraph (ii) above may be fastened in place during the entire flight. It will not be necessary to have such devices unlatched during takeoff and landing. Auxiliary safety devices such as safety chains or bars that do not meet the standards of paragraph (ii) above may be used provided operating instructions are installed at or near the device and a placard is installed requiring the removal of such devices prior to takeoff and landing. For related guidance, Refer to paragraph 351b(3). (Amendment 25- 0)
(3) Paragraph (b). Power operated external doors. Power operated doors should be so designed that the door can be opened by manual means even when power is inactivated. The loss of power should not cause the door to become unlatched. Since emergency landings, such as the wheels-up condition, may result in the severance of electrical wires or rupture of hydraulic and pneumatic lines, the power which may be needed for operation of the doors or exits may be lost. Similarly, it is conceivable that under emergency conditions, the electrical power source may be purposely interrupted to reduce the possibility of fire. (Amendment 25-0)
(4) Paragraphs (b) and (e). Means for safeguarding against inadvertent opening in flight. Auxiliary locking devices may be used to reduce the probability of inadvertent opening in flight provided they meet the standards and conditions covered above. (Amendment 25-0)
(i) It is acceptable to create a limited access zone in front of the door to eliminate the possibility of a passenger using the door handle as a steadying means and thereby inadvertently opening the door. Although providing a restricted zone by means of a barrier may appear to conflict with the requirements of § 25.813 for an unobstructed passageway to Type I, and Type II emergency exits, it is considered that it would contribute sufficiently to the overall safety of the airplane occupants to be permitted. This device may be a rope, chain, rigid bar or gate. Such installations should be waist high to provide the maximum benefits for an adult and the end fastenings should be simple to make removal easy. It is not considered acceptable to install full-length auxiliary doors, but waist-high rigid gates would be acceptable provided they open toward the door and will not block the opening of the cabin door in any way. The locking means should be one, which could be easily overridden such as a spring-loaded ball type latch. (Amendment 25-0)
(ii) Flexible gates such as those made from webbing are not acceptable on the basis that persons may become entangled during an emergency egress. The use of a barrier to prevent persons from inadvertently opening the door in flight does not eliminate the need for a safety means to provide for possible malfunctioning of the primary locking mechanism; however, the auxiliary safety means covered above may eliminate the need for a restricted zone. (Amendment 25-0)
(5) Paragraph (e). Direct visual inspection. The means of complying with paragraph (e) of this section will depend upon the type of door and locking mechanism used. In all cases there should be provisions to ascertain that an unsatisfactory condition does not exist after closing the door. In some instances a central window for viewing the position of the mechanism may be sufficient while other cases may require one or more windows in the door frame to permit inspection of the bayonet location relative to that portion of the lock in the door frame. The need for or the number and location of inspection openings or windows will depend on the type of door and locking mechanism used. (Amendment 25-0)
(6) Paragraph (e). Visual indicating system. The objective herein is to be able to ascertain by visual means that the door or locking means is sufficiently engaged to eliminate hazards emanating from an improperly closed door. Outward opening doors present a different problem from inward opening doors. (Amendment 25-0)
(i) The visual indicating system may consist of an indicator for each individual door, or a system connecting all doors in series. If the latter system is used, it need not necessarily show which door is not fully locked. (Amendment 25-0)
(ii) It is not necessary that more than one crewmember be able to ascertain by a visual signal that all external doors, normally used by the crew in supplying the airplane, or in loading and unloading passengers and cargo, are fully closed and locked. The visual signal should be located so that it may easily be seen by the appropriate crewmember from his station. (Amendment 25-0)
25.783 › Amendment 25-15
62. AMENDMENT 25-15, Effective October 24, 1967.
a. Regulation.
(a) Each cabin must have at least one easily accessible external door.
(b) There must be a means to lock and safeguard each external door against opening in flight (either inadvertently by persons or as a result of mechanical failure). Each external door must be openable from both the inside and the outside, even though persons may be crowded against the door on the inside of the airplane. Inward opening doors may be used if there are means to prevent occupants from crowding against the door to an extent that would interfere with the opening of the door. The means of opening must be simple and obvious and must be arranged and marked so that it can be readily located and operated, even in darkness. Auxiliary locking devices may be used.
(c) Each external door must be reasonably free from jamming as a result of fuselage deformation in a minor crash.
(d) Each external door must be located where persons using them will not be endangered by the propellers when appropriate operating procedures are used.
(e) There must be a provision for direct visual inspection of the locking mechanism by crewmembers to determine whether external doors, for which the initial opening movement is outward (including passenger, crew, service, and cargo doors), are fully locked. In addition, there must be a visual means to signal to appropriate crewmembers when normally used external doors are closed and fully locked.
(f) Cargo and service doors not suitable for use as an exit in an emergency need only meet paragraph (e) of this section and be safeguarded against opening in flight as a result of mechanical failure.
[(g) Each passenger entry door in the side of the fuselage must qualify as a Type A, Type I, or Type II passenger emergency exit and must meet the requirements of §§ 25.807 through 25.813 that apply to that type of passenger emergency exit. If an integral stair is installed at such a passenger entry door, the stair must be designed so that when subjected to the inertia forces specified in § 25.561, and following the collapse of one or more legs of the landing gear, it will not interfere to an extent that will reduce the effectiveness of emergency egress through the passenger entry door.]
b. Guidance.
(l) Paragraphs (b) through (e). The requirements of these paragraphs apply to all cabin and pilot compartment external doors usable for entrance or egress. It is not restricted to the
main cabin door. Cargo and service doors not suitable for emergency egress need only comply with § 25.783(e) and be safeguarded against opening in flight as a result of mechanical failure. (Amendment 25-0)
(2) Paragraph (b). Auxiliary locking devices. (Amendment 25-0)
(i) The use of auxiliary locking devices is permitted. Such devices would include dual locking handles, other types of locking and safety devices, two position handles, and dual operation handles (where one operation such as pushing or pulling on the handle unlocks the latching mechanism and the second operation of turning the handle unlatches the door for opening). Auxiliary locking devices should be used only as an additional safety factor and should not be used as a means of correcting an inadequate design of the primary locking or latching means. The advantages to be gained from the installation of auxiliary or dual locking devices (safety chains and dual handle main locking means) should be weighed against the need to easily and rapidly open the door in case of emergencies so that the overall level of safety is as high as practicable. (Amendment 25-0)
(ii) All locking or safety means, including safety chains and latches of any kind, should be so positioned and designed that their presence, location and means of operation are obvious to one not familiar with door designs. (Amendment 25-0)
(A) The means of fastening safety devices should be sufficiently simple to make removal easy. (Amendment 25-0)
(B) Any emergency release mechanism installed to release the safety device should operate with a simple motion and upon the application of relatively small forces. (Amendment 25-0)
(C) All locking devices should be readily operable from both inside and outside of the airplane and be appropriately marked both inside and outside. (Amendment 25-0)
(iii) Auxiliary safety devices meeting the standards of paragraph (ii) above may be fastened in place during the entire flight. It will not be necessary to have such devices unlatched during takeoff and landing. Auxiliary safety devices such as safety chains or bars that do not meet the standards of paragraph (ii) above may be used provided operating instructions are installed at or near the device and a placard is installed requiring the removal of such devices prior to takeoff and landing. For related guidance, Refer to paragraph 351b(3). (Amendment 25- 0)
(3) Paragraph (b). Power operated external doors. Power operated doors should be so designed that the door can be opened by manual means even when power is inactivated. The loss of power should not cause the door to become unlatched. Since emergency landings, such as the wheels-up condition, may result in the severance of electrical wires or rupture of hydraulic and pneumatic lines, the power which may be needed for operation of the doors or exits may be lost. Similarly, it is conceivable that under emergency conditions, the electrical power source may be purposely interrupted to reduce the possibility of fire. (Amendment 25-0)
(4) Paragraphs (b) and (e). Means for safeguarding against inadvertent opening in flight. Auxiliary locking devices may be used to reduce the probability of inadvertent opening in flight provided they meet the standards and conditions covered above. (Amendment 25-0)
(i) It is acceptable to create a limited access zone in front of the door to eliminate the possibility of a passenger using the door handle as a steadying means and thereby inadvertently opening the door. Although providing a restricted zone by means of a barrier may appear to conflict with the requirements of § 25.813 for an unobstructed passageway to Type I, and Type II emergency exits, it is considered that it would contribute sufficiently to the overall safety of the airplane occupants to be permitted. This device may be a rope, chain, rigid bar or gate. Such installations should be waist high to provide the maximum benefits for an adult and the end fastenings should be simple to make removal easy. It is not considered acceptable to install full-length auxiliary doors, but waist-high rigid gates would be acceptable provided they open toward the door and will not block the opening of the cabin door in any way. The locking means should be one, which could be easily overridden such as a spring-loaded ball type latch. (Amendment 25-0)
(ii) Flexible gates such as those made from webbing are not acceptable on the basis that persons may become entangled during an emergency egress. The use of a barrier to prevent persons from inadvertently opening the door in flight does not eliminate the need for a safety means to provide for possible malfunctioning of the primary locking mechanism; however, the auxiliary safety means covered above may eliminate the need for a restricted zone. (Amendment 25-0)
(5) Paragraph (e). Direct visual inspection. The means of complying with paragraph (e) of this section will depend upon the type of door and locking mechanism used. In all cases there should be provisions to ascertain that an unsatisfactory condition does not exist after closing the door. In some instances a central window for viewing the position of the mechanism may be sufficient while other cases may require one or more windows in the door frame to permit inspection of the bayonet location relative to that portion of the lock in the door frame. The need for or the number and location of inspection openings or windows will depend on the type of door and locking mechanism used. (Amendment 25-0)
(6) Paragraph (e). Visual indicating system. The objective herein is to be able to ascertain by visual means that the door or locking means is sufficiently engaged to eliminate hazards emanating from an improperly closed door. Outward opening doors present a different problem from inward opening doors. (Amendment 25-0)
(i) The visual indicating system may consist of an indicator for each individual door, or a system connecting all doors in series. If the latter system is used, it need not necessarily show which door is not fully locked. (Amendment 25-0)
(ii) It is not necessary that more than one crewmember be able to ascertain by a visual signal that all external doors, normally used by the crew in supplying the airplane, or in
25.783 › Amendment 25-23
loading and unloading passengers and cargo, are fully closed and locked. The visual signal should be located so that it may easily be seen by the appropriate crewmember from his station. (Amendment 25-0)
63. AMENDMENT 25-23, Effective May 8, 1970.
a. Regulation.
(a) Each cabin must have at least one easily accessible external door.
(b) There must be a means to lock and safeguard each external door against opening in flight (either inadvertently by persons or as a result of mechanical failure [or failure of a single structural element]). Each external door must be openable from both the inside and the outside, even though persons may be crowded against the door on the inside of the airplane. Inward opening doors may be used if there are means to prevent occupants from crowding against the door to an extent that would interfere with the opening of the door. The means of opening must be simple and obvious and must be arranged and marked so that it can be readily located and operated, even in darkness. Auxiliary locking devices may be used.
(c) Each external door must be reasonably free from jamming as a result of fuselage deformation in a minor crash.
(d) Each external door must be located where persons using them will not be endangered by the propellers when appropriate operating procedures are used.
(e) There must be a provision for direct visual inspection of the locking mechanism by crewmembers to determine whether external doors, for which the initial opening movement is outward (including passenger, crew, service, and cargo doors), are fully locked. In addition, there must be a visual means to signal to appropriate crewmembers when normally used external doors are closed and fully locked.
(f) Cargo and service doors not suitable for use as an exit in an emergency need only meet paragraph (e) of this section and be safeguarded against opening in flight as a result of mechanical failure [or failure of a single structural element].
(g) Each passenger entry door in the side of the fuselage must qualify as a Type A, Type I, or Type II passenger emergency exit and must meet the requirements of §§ 25.807 through 25.813 that apply to that type of passenger emergency exit. If an integral stair is installed at such a passenger entry door, the stair must be designed so that when subjected to the inertia forces specified in § 25.561, and following the collapse of one or more legs of the landing gear, it will not interfere to an extent that will reduce the effectiveness of emergency egress through the passenger entry door.
b. Guidance.
(l) Paragraphs (b) through (e). The requirements of these paragraphs apply to all cabin and pilot compartment external doors usable for entrance or egress. It is not restricted to the main cabin door. Cargo and service doors not suitable for emergency egress need only comply with § 25.783(e) and be safeguarded against opening in flight as a result of mechanical failure. (Amendment 25-0)
(2) Paragraph (b). Auxiliary locking devices. (Amendment 25-0)
(i) The use of auxiliary locking devices is permitted. Such devices would include dual locking handles, other types of locking and safety devices, two position handles, and dual operation handles (where one operation such as pushing or pulling on the handle unlocks the latching mechanism and the second operation of turning the handle unlatches the door for opening). Auxiliary locking devices should be used only as an additional safety factor and should not be used as a means of correcting an inadequate design of the primary locking or latching means. The advantages to be gained from the installation of auxiliary or dual locking devices (safety chains and dual handle main locking means) should be weighed against the need to easily and rapidly open the door in case of emergencies so that the overall level of safety is as high as practicable. (Amendment 25-0)
(ii) All locking or safety means, including safety chains and latches of any kind, should be so positioned and designed that their presence, location and means of operation are obvious to one not familiar with door designs. (Amendment 25-0)
(A) The means of fastening safety devices should be sufficiently simple to make removal easy. (Amendment 25-0)
(B) Any emergency release mechanism installed to release the safety device should operate with a simple motion and upon the application of relatively small forces. (Amendment 25-0)
(C) All locking devices should be readily operable from both inside and outside of the airplane and be appropriately marked both inside and outside. (Amendment 25-0)
(iii) Auxiliary safety devices meeting the standards of paragraph (ii) above may be fastened in place during the entire flight. It will not be necessary to have such devices unlatched during takeoff and landing. Auxiliary safety devices such as safety chains or bars that do not meet the standards of paragraph (ii) above may be used provided operating instructions are installed at or near the device and a placard is installed requiring the removal of such devices prior to takeoff and landing. For related guidance, Refer to paragraph 351b(3). (Amendment 25- 0)
(3) Paragraph (b). Power operated external doors. Power operated doors should be so designed that the door can be opened by manual means even when power is inactivated. The
loss of power should not cause the door to become unlatched. Since emergency landings, such as the wheels-up condition, may result in the severance of electrical wires or rupture of hydraulic and pneumatic lines, the power which may be needed for operation of the doors or exits may be lost. Similarly, it is conceivable that under emergency conditions, the electrical power source may be purposely interrupted to reduce the possibility of fire. (Amendment 25-0)
(4) Paragraphs (b) and (e). Means for safeguarding against inadvertent opening in flight. Auxiliary locking devices may be used to reduce the probability of inadvertent opening in flight provided they meet the standards and conditions covered above. (Amendment 25-0)
(i) It is acceptable to create a limited access zone in front of the door to eliminate the possibility of a passenger using the door handle as a steadying means and thereby inadvertently opening the door. Although providing a restricted zone by means of a barrier may appear to conflict with the requirements of § 25.813 for an unobstructed passageway to Type I, and Type II emergency exits, it is considered that it would contribute sufficiently to the overall safety of the airplane occupants to be permitted. This device may be a rope, chain, rigid bar or gate. Such installations should be waist high to provide the maximum benefits for an adult and the end fastenings should be simple to make removal easy. It is not considered acceptable to install full-length auxiliary doors, but waist-high rigid gates would be acceptable provided they open toward the door and will not block the opening of the cabin door in any way. The locking means should be one, which could be easily overridden such as a spring-loaded ball type latch. (Amendment 25-0)
(ii) Flexible gates such as those made from webbing are not acceptable on the basis that persons may become entangled during an emergency egress. The use of a barrier to prevent persons from inadvertently opening the door in flight does not eliminate the need for a safety means to provide for possible malfunctioning of the primary locking mechanism; however, the auxiliary safety means covered above may eliminate the need for a restricted zone. (Amendment 25-0)
(5) Paragraph (e). Direct visual inspection. The means of complying with paragraph (e) of this section will depend upon the type of door and locking mechanism used. In all cases there should be provisions to ascertain that an unsatisfactory condition does not exist after closing the door. In some instances a central window for viewing the position of the mechanism may be sufficient while other cases may require one or more windows in the door frame to permit inspection of the bayonet location relative to that portion of the lock in the door frame. The need for or the number and location of inspection openings or windows will depend on the type of door and locking mechanism used. (Amendment 25-0)
(6) Paragraph (e). Visual indicating system. The objective herein is to be able to ascertain by visual means that the door or locking means is sufficiently engaged to eliminate hazards emanating from an improperly closed door. Outward opening doors present a different problem from inward opening doors. (Amendment 25-0)
25.783 › Amendment 25-54
(i) The visual indicating system may consist of an indicator for each individual door, or a system connecting all doors in series. If the latter system is used, it need not necessarily show which door is not fully locked. (Amendment 25-0)
(ii) It is not necessary that more than one crewmember be able to ascertain by a visual signal that all external doors, normally used by the crew in supplying the airplane, or in loading and unloading passengers and cargo, are fully closed and locked. The visual signal should be located so that it may easily be seen by the appropriate crewmember from his station. (Amendment 25-0)
64. AMENDMENT 25-54, Effective October 14, 1980.
a. Regulation.
(a) Each cabin must have at least one easily accessible external door.
(b) There must be a means to lock and safeguard each external door against opening in flight (either inadvertently by persons or as a result of mechanical failure or failure of a single structural element [either during or after closure]). Each external door must be openable from both the inside and the outside, even though persons may be crowded against the door on the inside of the airplane. Inward opening doors may be used if there are means to prevent occupants from crowding against the door to an extent that would interfere with the opening of the door. The means of opening must be simple and obvious and must be arranged and marked so that it can be readily located and operated, even in darkness. Auxiliary locking devices may be used.
(c) Each external door must be reasonably free from jamming as a result of fuselage deformation in a minor crash.
(d) Each external door must be located where persons using them will not be endangered by the propellers when appropriate operating procedures are used.
[(e) There must be a provision for direct visual inspection of the locking mechanism to determine if external doors, for which the initial opening movement is not inward (including passenger, crew, service, and cargo doors), are fully closed and locked. The provision must be discernible under operational lighting conditions by appropriate crewmembers using a flashlight or equivalent lighting source. In addition, there must be a visual warning means to signal the appropriate flight crewmembers if any external door is not fully closed and locked. The means must be designed such that any failure or combination of failures that would result in an erroneous closed and locked indication is improbable for doors for which the initial opening movement is not inward.
(f) External doors must have provisions to prevent the initiation of pressurization of the airplane to an unsafe level if the door is not fully closed and locked. In addition,
it must be shown by safety analysis that inadvertent opening is extremely improbable.]
[(g)] Cargo and service doors not suitable for use as an exit in an emergency need only meet paragraph (e) of this section and be safeguarded against opening in flight as a result of mechanical failure or failure of a single structural element.
(h) Each passenger entry door in the side of the fuselage must qualify as a Type A, Type I, or Type II passenger emergency exit and must meet the requirements of §§ 25.807 through 25.813 that apply to that type of passenger emergency exit.
(i) If an integral stair is installed in a passenger entry door that is qualified as a passenger emergency exit, the stair must be designed so that under the following conditions the effectiveness of passenger emergency egress will not be impaired:
(1) The door, integral stair, and operating mechanism have been subjected to the inertia forces specified in § 25.561(b)(3), acting separately relative to the surrounding structure.
[(2) The airplane is in the normal ground attitude and in each of the attitudes corresponding to collapse of one or more legs of the landing gear.
(j) All lavatory doors must be designed to preclude anyone from becoming trapped inside the lavatory, and if a locking mechanism is installed, it be capable of being unlocked from the outside without the aid of special tools.]
b. Guidance.
(1) Refer to § 25.809 for related requirements, and AC 25.783-1, “Fuselage, Doors, Hatches, and Exits,” dated 12/10/86, for related guidance. (Amendment 25-54)
(2) Paragraph (b). Protection against inadvertent exit door openings is required, but at the same time, a single-motion handle operation to open a passenger door should be provided to facilitate emergency egress. Auxiliary locking devices that complicate the door opening process may be accepted as necessary, though undesirable, if it can be substantiated that there is no other practicable means of protecting against inadvertent exit door opening. (Amendment 25-54)
(i) Auxiliary locking devices that may initially be assumed to be necessary, in fact might be eliminated by assuring that the door is designed in accordance with human factors principles. A door that is opened by moving a handle from the up position to a down position represents a design contrary to the convention believed to be familiar to most people in the aircraft industry. Therefore, this design may lend itself to contributing to an inadvertent door opening, as has actually happened. In addition, a door handle that is in the up position when the door is closed lends itself to more easily being used as a handhold in flight, which may result in an inadvertent opening. The threat inherent in this design would practically mandate the inclusion of auxiliary locking devices, to the possible detriment of emergency egress capability.
On the other hand, a door handle which operates in a conventional manner (i.e., moves up to open, moves down to close) is not as prone to inappropriate operation, nor is it in a location as susceptible for use as a handhold in flight. Consequently, this design, in addition to being more user-friendly from a human factors viewpoint, may eliminate any need for auxiliary locking devices. (Amendment 25-54)
(ii) Handles which operate in a rotary manner (in a plane parallel to that of the door) are not known to have been implicated in any incidents as noted above, nor has clockwise versus counterclockwise rotary motion been known to be controversial in this regard (except that counterclockwise may be the most universally accepted convention for opening jars, faucets, etc.). Likewise, these handles have not been considered to represent the attractive handhold devices in flight that other types of handles might and, furthermore, they require a deliberate effort to actuate. (Amendment 25-54)
(iii) When it can be substantiated to the satisfaction of the FAA that auxiliary locking devices are necessary to comply with the inadvertent door opening requirements of §§ 25.783(a) and 25.809(f), and it is not through design defect that these devices are provided, any potentially adverse impact of these devices on emergency egress must be minimized through adherence to the available guidance pertinent to auxiliary locking devices. "Design defect" in this context may reasonably be considered to include designs which neglect to address known human factors concerns as highlighted herein. Auxiliary locking devices which are deemed to be not simple and obvious, are not acceptable. Devices which are hidden by design or color, recessed, contoured, camouflaged, or otherwise concealed to the degree that a naive person may need to read a placard to determine how to open the door are not simple and obvious, and are therefore not acceptable. Suitable demonstrations may be required to substantiate acceptability in this regard. (Amendment 25-54)
(3) Paragraphs (b) through (e). The requirements of these paragraphs apply to all cabin and pilot compartment external doors usable for entrance or egress. It is not restricted to the main cabin door. (Amendment 25-0)
(4) Paragraph (b). Auxiliary locking devices. (Amendment 25-0)
(i) The use of auxiliary locking devices is permitted. Such devices would include dual locking handles, other types of locking and safety devices, two position handles, and dual operation handles (where one operation such as pushing or pulling on the handle unlocks the latching mechanism and the second operation of turning the handle unlatches the door for opening). Auxiliary locking devices should be used only as an additional safety factor and should not be used as a means of correcting an inadequate design of the primary locking or latching means. The advantages to be gained from the installation of auxiliary or dual locking devices (safety chains and dual handle main locking means) should be weighed against the need to easily and rapidly open the door in case of emergencies so that the overall level of safety is as high as practicable. (Amendment 25-0)
(ii) All locking or safety means, including safety chains and latches of any kind, should be so positioned and designed that their presence, location and means of operation are obvious to one not familiar with door designs. (Amendment 25-0)
(A) The means of fastening safety devices should be sufficiently simple to make removal easy. (Amendment 25-0)
(B) Any emergency release mechanism installed to release the safety device should operate with a simple motion and upon the application of relatively small forces. (Amendment 25-0)
(C) All locking devices should be readily operable from both inside and outside of the airplane and be appropriately marked both inside and outside. (Amendment 25-0)
(iii) Auxiliary safety devices meeting the standards of paragraph (ii) above may be fastened in place during the entire flight. It will not be necessary to have such devices unlatched during takeoff and landing. Auxiliary safety devices such as safety chains or bars that do not meet the standards of paragraph (ii) above may be used provided operating instructions are installed at or near the device and a placard is installed requiring the removal of such devices prior to takeoff and landing. For related guidance, Refer to paragraph 351b(3). (Amendment 25- 0)
(5) Paragraph (b). Power operated external doors. Power operated doors should be so designed that the door can be opened by manual means even when power is inactivated. The loss of power should not cause the door to become unlatched. Since emergency landings, such as the wheels-up condition, may result in the severance of electrical wires or rupture of hydraulic and pneumatic lines, the power which may be needed for operation of the doors or exits may be lost. Similarly, it is conceivable that under emergency conditions, the electrical power source may be purposely interrupted to reduce the possibility of fire. (Amendment 25-0)
(i) It is acceptable to create a limited access zone in front of the door to eliminate the possibility of a passenger using the door handle as a steadying means and thereby inadvertently opening the door. Although providing a restricted zone by means of a barrier may appear to conflict with the requirements of § 25.813 for an unobstructed passageway to Type I, and Type II emergency exits, it is considered that it would contribute sufficiently to the overall safety of the airplane occupants to be permitted. This device may be a rope, chain, rigid bar or gate. Such installations should be waist high to provide the maximum benefits for an adult and the end fastenings should be simple to make removal easy. It is not considered acceptable to install full-length auxiliary doors, but waist-high rigid gates would be acceptable provided they open toward the door and will not block the opening of the cabin door in any way. The locking means should be one, which could be easily overridden such as a spring-loaded ball type latch. (Amendment 25-0)
(ii) Flexible gates such as those made from webbing are not acceptable on the basis that persons may become entangled during an emergency egress. The use of a barrier to prevent persons from inadvertently opening the door in flight does not eliminate the need for a safety
means to provide for possible malfunctioning of the primary locking mechanism; however, the auxiliary safety means covered above may eliminate the need for a restricted zone. (Amendment 25-0)
25.783 › Amendment 25-72
(6) Paragraph (e). Visual indicating system. The objective herein is to be able to ascertain by visual means that the door or locking means is sufficiently engaged to eliminate hazards emanating from an improperly closed door. Outward opening doors present a different problem from inward opening doors. (Amendment 25-0)
(i) The visual indicating system may consist of an indicator for each individual door, or a system connecting all doors in series. If the latter system is used, it need not necessarily show which door is not fully locked. (Amendment 25-0)
(ii) It is not necessary that more than one crewmember be able to ascertain by a visual signal that all external doors, normally used by the crew in supplying the airplane, or in loading and unloading passengers and cargo, are fully closed and locked. The visual signal should be located so that it may easily be seen by the appropriate crewmember from his station. (Amendment 25-0)
65. AMENDMENT 25-72, Effective August 20, 1990.
a. Regulation.
(a) Each cabin must have at least one easily accessible external door.
(b) There must be a means to lock and safeguard each external door against opening in flight (either inadvertently by persons or as a result of mechanical failure or failure of a single structural element either during or after closure). Each external door must be openable from both the inside and the outside, even though persons may be crowded against the door on the inside of the airplane. Inward opening doors may be used if there are means to prevent occupants from crowding against the door to an extent that would interfere with the opening of the door. The means of opening must be simple and obvious and must be arranged and marked so that it can be readily located and operated, even in darkness. Auxiliary locking devices may be used.
(c) Each external door must be reasonably free from jamming as a result of fuselage deformation in a minor crash.
(d) Each external door must be located where persons using them will not be endangered by the propellers when appropriate operating procedures are used.
(e) There must be a provision for direct visual inspection of the locking mechanism to determine if external doors, for which the initial opening movement is not inward (including passenger, crew, service, and cargo doors), are fully closed and locked. The provision must be discernible under operational lighting conditions by appropriate crewmembers using a flashlight or equivalent lighting source. In
addition, there must be a visual warning means to signal the appropriate flight crewmembers if any external door is not fully closed and locked. The means must be designed such that any failure or combination of failures that would result in an erroneous closed and locked indication is improbable for doors for which the initial opening movement is not inward.
(f) External doors must have provisions to prevent the initiation of pressurization of the airplane to an unsafe level if the door is not fully closed and locked. In addition, it must be shown by safety analysis that inadvertent opening is extremely improbable.
[(g) Cargo and service doors not suitable for use as emergency exits need only meet paragraphs (e) and (f) of this section and be safeguarded against opening in flight as a result of mechanical failure or failure of a single structural element.]
(h) Each passenger entry door in the side of the fuselage must qualify as a Type A, Type I, or Type II passenger emergency exit and must meet the requirements of §§ 25.807 through 25.813 that apply to that type of passenger emergency exit.
(i) If an integral stair is installed in a passenger entry door that is qualified as a passenger emergency exit, the stair must be designed so that under the following conditions the effectiveness of passenger emergency egress will not be impaired:
(1) The door, integral stair, and operating mechanism have been subjected to the inertia forces specified in § 25.561(b)(3), acting separately relative to the surrounding structure.
(2) The airplane is in the normal ground attitude and in each of the attitudes corresponding to collapse of one or more legs of the landing gear.
(j) All lavatory doors must be designed to preclude anyone from becoming trapped inside the lavatory, and if a locking mechanism is installed, it be capable of being unlocked from the outside without the aid of special tools.
b. Guidance.
(1) Refer to § 25.809 for related requirements, and AC 25.783-1, “Fuselage, Doors, Hatches, and Exits,” dated 12/10/86, for related guidance. (Amendment 25-54)
(2) Paragraph (b). Protection against inadvertent exit door openings is required, but at the same time, a single-motion handle operation to open a passenger door should be provided to facilitate emergency egress. Auxiliary locking devices that complicate the door opening process may be accepted as necessary, though undesirable, if it can be substantiated that there is no other practicable means of protecting against inadvertent exit door opening. (Amendment 25-54)
(i) Auxiliary locking devices that may initially be assumed to be necessary, in fact might be eliminated by assuring that the door is designed in accordance with human factors principles. A door that is opened by moving a handle from the up position to a down position represents a design contrary to the convention believed to be familiar to most people in the aircraft industry. Therefore, this design may lend itself to contributing to an inadvertent door opening, as has actually happened. In addition, a door handle that is in the up position when the door is closed lends itself to more easily being used as a handhold in flight, which may result in an inadvertent opening. The threat inherent in this design would practically mandate the inclusion of auxiliary locking devices, to the possible detriment of emergency egress capability. On the other hand, a door handle which operates in a conventional manner (i.e., moves up to open, moves down to close) is not as prone to inappropriate operation, nor is it in a location as susceptible for use as a handhold in flight. Consequently, this design, in addition to being more user-friendly from a human factors viewpoint, may eliminate any need for auxiliary locking devices. (Amendment 25-54)
(ii) Handles which operate in a rotary manner (in a plane parallel to that of the door) are not known to have been implicated in any incidents as noted above, nor has clockwise versus counterclockwise rotary motion been known to be controversial in this regard (except that counterclockwise may be the most universally accepted convention for opening jars, faucets, etc.). Likewise, these handles have not been considered to represent the attractive handhold devices in flight that other types of handles might and, furthermore, they require a deliberate effort to actuate. (Amendment 25-54)
Continue reading ↓ 120 of 2104 passages shown