AC 21.101-1B Establishing the Certification Basis of Changed Aeronautical Products
This advisory circular (AC) provides guidance for the application ofthe "Changed Product Rule (CPR)," pursuant to Title 14 ofthe Code ofFederal Regulations (14 CFR) 21.101, Designation ofapplicable regulations, and 21.19, Changes requiring a new type certificate, for changes made to type certificated aeronautical products.
AC 21.101-1B
Advisory
Circular
U.S. Department of Transportation Federal Aviation Administration
Subject: Establishing the Certification Basis of Changed Aeronautical Products
Date: March 11, 2016 AC No: 21.101-18 Initiated By: AIR-1 00
This advisory circular (AC) provides guidance for the application ofthe "Changed Product Rule (CPR)," pursuant to Title 14 ofthe Code ofFederal Regulations (14 CFR) 21.101, Designation ofapplicable regulations, and 21.19, Changes requiring a new type certificate, for changes made to type certificated aeronautical products.
If you have suggestions for improving this AC, you may use the feedback form at the end ofthis AC.
Acting ::~~~
Manager, Design, Manufacturing
& Airworthi Division Aircraft Certification Service
ness
AC 21.101-1B › CONTENTS
03/11/16 AC 21.101-1B
CONTENTS
Paragraph Page
ii
Chapter 1. Introduction … 1-1
1.1 Purpose … 1-1
1.2 Applicability … 1-1
1.3 Cancellation … 1-1
1.4 AC Content … 1-1
1.5 Terms Used in this AC … 1-3
Chapter 2. Overview of §§ 21.19 and 21.101 … 2-1
2.1 Section 21.19 … 2-1
2.2 Section 21.101 … 2-1
Chapter 3. Process for Establishing the Certification Basis for Changed Products … 3-1
3.1 Overview … 3-1
3.2 Step 1. Identify the Proposed Type Design Changes to an Aeronautical Product … 3-3
3.3 Step 2. Verify the Proposed Type Design Change is Not Substantial … 3-4
3.4 Step 3. Will you Use the Latest Standards? … 3-4
3.5 Step 4. Arrange Changes into Related and Unrelated Groups … 3-5
3.6 Step 5. Is Each Related or Unrelated Group a Significant Change? … 3-6
3.7 Proposing an Amendment Level for a Significant Change … 3-9
3.8 Proposing an Amendment Level for a Not Significant Change … 3-9
3.9 Step 6. Prepare your Proposed Certification Basis List … 3-9
3.10 Step 7. Do the Latest Requirements Contribute Materially to the Level of Safety and are They Practical? … 3-11
3.11 Step 8. Ensure Proposed Certification Basis is Adequate … 3-17
Chapter 4. Excepted Products under § 21.101(c) … 4-1
4.1 Excepted Products … 4-1
Chapter 5. Other Considerations … 5-1
5.1 Design-Related Operating Requirements … 5-1
5.2 FAA Policy … 5-1
5.3 A Baseline Product Consists of One Unique Type Design Configuration … 5-1
5.4 Predecessor Regulations … 5-2
03/11/16 AC 21.101-1B
CONTENTS (CONTINUED)
Paragraph Page
iii
5.5 Special Conditions, § 21.101(d) … 5-2
5.6 Effective Period for an Application to Change a Type Certificate, § 21.101(e) … 5-2
5.7 Other Category Aircraft, § 21.101(f) … 5-3
5.8 Clarification of § 21.101(g), Part 26 Requirements … 5-5
5.9 Documentation … 5-5
5.10 Incorporation of STCs into the Type Design … 5-6
5.11 Removing Design Changes … 5-6
5.12 The Certification Basis is Part of the Design Change … 5-7
5.13 Sequential Design Changes—Cumulative Effects … 5-7
Appendix A. Classification of Design Changes … A-1
Appendix B. Application Charts for Changed Product Rule … B-1
Appendix C. A Method to Determine the Changed and Affected Areas … C-1
Appendix D. Other Guidance for Affected Areas … D-1
Appendix E. Procedure for Evaluating Material Contribution to Safety or Impracticality of Applying Latest Requirements to a Changed Product … E-1
Appendix F. The Use of Service Experience in the Exception Process … F-1
Appendix G. Changed Product Rule Decision Record … G-1
Appendix H. Examples of Documenting the Proposed Certification Basis List … H-1
Appendix I. Related Documents … I-1
Appendix J. Definitions and Terminology … J-1
AC 21.101-1B › TABLES
03/11/16 AC 21.101-1B
CONTENTS (CONTINUED)
iv
FIGURES
Number Page
Figure 3-1. Developing a Proposed Certification Basis for a Changed Product Pursuant to § 21.101 … 3-2
Figure 3-2. Related and Unrelated Changes for Example of Increasing the Maximum Number of Passengers … 3-6
Figure 3-3. Affected Areas versus Not Affected Areas … 3-10
Figure 3-4. Design Change Affected Areas with Secondary Changes … 3-14
Figure C-1. Method to Determine the Changed and Affected Areas … C-1
Figure E-1. Safety Benefits versus Resources … E-2
TABLES
Number Page
Table A-1. Examples of Substantial Changes for Small Airplanes (Part 23) … A-1
Table A-2. Examples of Significant Changes for Small Airplanes (Part 23) … A-3
Table A-3. Examples of Not Significant Changes for Small Airplanes (Part 23) … A-14
Table A-4. Examples of Substantial Changes for Transport Airplanes (Part 25) … A-25
Table A-5. Examples of Significant Changes for Transport Airplanes (Part 25) … A-26
Table A-6. Examples of Not Significant Changes for Transport Airplanes (Part 25) … A-38
Figure 3-1 · page 4Picture of the page from the copy saved here
Table A-7. Examples of Substantial Changes for Rotorcraft (Parts 27 and 29) … A-49
Table A-8. Examples of Significant Changes for Rotorcraft (Parts 27 and 29) … A-50
Table A-9. Examples of Not Significant Changes for Rotorcraft (Parts 27 and 29) … A-56
Table A-10. Examples of Substantial Changes for Engines (Part 33) … A-64
Table A-11. Examples of Significant Changes for Engines (Part 33) … A-65
Table A-12. Examples of Not Significant Changes for Engines (Part 33) … A-72
Table A-13. Example of a Substantial Change for Propellers (Part 35) … A-80
Table A-14. Examples of Significant Changes for Propellers (Part 35) … A-80
Table A-15. Examples of Not Significant Changes for Propellers (Part 35) … A-84
Table B-1. Application Chart for § 21.101(a) and (b) and § 21.19 … B-1
Table B-2. Application Chart for § 21.101(c) Excepted Products … B-2
03/11/16 AC 21.101-1B
CONTENTS (CONTINUED)
TABLES (CONTINUED)
Number Page
v
Table C-1. Example of Associating a Physical Change with the Applicable Airworthiness Requirements … C-2
Table C-2. Example of a Functional Change, Affected Areas, and Associated Effects … C-3
Table C-3. Example of Associating Affected Areas with the Applicable Airworthiness Requirements … C-4
Table C-4. Example of a Combined List of Physical and Functional Changes with Applicable Airworthiness Requirements … C-5
Table H-1. Tabular Form for Documenting a Proposed Certification Basis … H-2
AC 21.101-1B › CHAPTER 1. INTRODUCTION
03/11/16 AC 21.101-1B
CHAPTER 1. INTRODUCTION
1.1 Purpose. This AC provides guidance for establishing the certification basis for changed aeronautical products pursuant to Title 14 of the Code of Federal Regulations (14 CFR) 21.101, Designation of the applicable regulations. The guidance is intended to help applicants and delegated organizations determine if it will be necessary to apply for a new type certificate (TC) under § 21.19, Changes requiring a new type certificate. The guidance describes the process for establishing the certification basis for an amended TC, supplemental type certificate (STC), and amended STC, detailing the requirements (evaluations, classifications, and decisions) throughout the process.
1.2 Applicability.
1.2.1 This AC is for applicants and holders of delegated organizations applying for amended TCs, STCs, or amended STCs.
1.2.2 This AC applies to major type design changes under § 21.101 for aeronautical products certificated under 14 CFR parts 21, 23, 25, 27, 29, 31, 33, and 35. References to “design change” include the design change and areas affected by the design change pursuant to § 21.101.
1.2.3 Minor type design changes are automatically considered not significant under the “does not contribute materially to the level of safety” provision of § 21.101(b).
1.2.4 This AC also applies to aircraft certificated under §§ 21.17(b), 21.19, 21.24, 21.25, and 21.27.
1.2.5 The term aeronautical product, or product, means a type certificated aircraft, aircraft engine, or propeller.
1.2.6 This AC is not intended to be used to determine the applicable aircraft noise, fuel venting, and exhaust emission requirements for changed products.
1.2.7 This AC is not mandatory and is not a regulation. This AC describes an acceptable means, but not the only means, to comply with § 21.101. However, if you use the means described in this AC, you must follow it entirely.
1.3 Cancellation. This AC cancels AC 21.101-1A, dated September 3, 2010.
1.4 AC Content. This AC contains 5 chapters and 10 appendices.
03/11/16 AC 21.101-1B
1.4.1 This chapter clarifies the purpose of this AC, describes its content, specifies the intended audience affected by this AC, clarifies which changes are within the scope of this AC, and references the definitions and terminology used in this AC.
1.4.2 Chapter 2 provides a general overview of §§ 21.101 and 21.19, clarifies the main principles and safety objectives, and directs applicants to the applicable guidance contained in subsequent chapters of this AC.
1.4.3 Chapter 3 contains guidance for implementation of § 21.101(b) to establish the type certification basis for changed aeronautical products. It describes in detail the various steps for developing the certification basis, a process that applies to all major design changes to aeronautical products. Chapter 3 also addresses § 21.19 considerations for identifying conditions under which an applicant for a type design change is required to submit an application for a new TC and provides guidance at which stage of the process this assessment is performed.
1.4.4 Chapter 4 provides guidance about products excepted from the requirement of § 21.101.
1.4.5 Chapter 5 contains considerations for—
• Design-related operating requirements,
• Determining which policy to apply to a design change,
• Defining a baseline product,
• Predecessor regulations,
• Using special conditions under § 21.101(d),
• The effective period of application for a change to a TC under § 21.101(e),
• Other category aircraft under § 21.101(f),
• Clarification of § 21.101(g) regarding 14 CFR part 26 requirements,
• Documenting revisions to the TC basis,
• Incorporating STCs into the type design,
• Removing design changes,
• Determining a certification basis after removing an approved design change, and
• Sequential design changes.
1.4.6 Appendix A contains examples of typical type design changes for small airplanes, transport airplanes, rotorcraft, engines, and propellers. The Federal Aviation Administration (FAA) has categorized these examples into individual tables according to the classifications of design change—“substantial,” “significant,” and “not significant.”
1.4.7 Appendix B contains application charts for applying the § 21.101 process, including the excepted process.
03/11/16 AC 21.101-1B
1.4.8 Appendix C contains one method for determining the changed and affected areas of a product.
1.4.9 Appendix D contains additional guidance on affected areas not discussed in other parts of this AC.
1.4.10 Appendix E provides detailed guidance with examples for evaluating the “impracticality” exception in the rule.
1.4.11 Appendix F provides guidance with examples on the use of relevant service experience in the certification process as one way to show that a later amendment may not contribute materially to the level of safety, allowing the use of earlier requirements.
1.4.12 Appendix G provides an example CPR decision record.
1.4.13 Appendix H provides examples of documenting a proposed certification basis list.
1.4.14 Appendix I lists the FAA regulations and orders related to this AC.
1.4.15 Appendix J lists the definitions and terminology applicable for application of the rule.
1.5 Terms Used in this AC.
1.5.1 The following terms are used interchangeably and have the same meaning: requirements, regulations, standards, and airworthiness standards.
1.5.2 The terms certification basis, type certification basis, and amendment are used interchangeably to refer to the groups of requirements defined above.
AC 21.101-1B › CHAPTER 2. OVERVIEW OF §§ 21.19 AND 21.101
03/11/16 AC 21.101-1B
CHAPTER 2. OVERVIEW OF §§ 21.19 AND 21.101
2.1 Section 21.19.
2.1.1 Section 21.19 requires an applicant to apply for a new TC for a changed product if the FAA finds that the change in design, power, thrust, or weight is so extensive that a substantially complete investigation of compliance with the applicable regulations is required.
2.1.2 Changes that require a substantial re-evaluation of the product’s compliance findings are referred to as “substantial changes.” For guidance, see paragraph 3.3 in chapter 3 of this AC. Appendix A of this AC provides examples of type design changes that will require a new TC.
2.1.3 If the FAA determines through § 21.19 that your proposed design change does not require a new TC, see § 21.101 for the applicable requirements to develop the certification basis for your proposed design change. For guidance, see chapter 3 and the examples in appendix A of this AC.
2.2 Section 21.101.
2.2.1 Section 21.101(a). Section 21.101(a) requires a change to a TC and the area affected by the change to comply with the latest requirements, unless the change meets the criteria for the exceptions identified in § 21.101(b) or (c). The intent of § 21.101 is to enhance safety by incorporating the latest requirements into the type certification basis for the changed product to the greatest extent practicable.
2.2.2 Section 21.101(b).
2.2.2.1 Section 21.101(b) pertains to when an applicant may show that a changed product complies with an earlier amendment of a regulation, provided that the earlier amendment is considered adequate and meets the criteria in § 21.101(b)(1), (2), or (3). When design changes involve features or characteristics that are novel and unusual as compared to the airworthiness standard at the proposed amendment, more recent airworthiness standards and/or special conditions will be applied for these features.
2.2.2.2 You can comply with the earlier requirements consistent with § 21.101(b), when—
2.2.2.2.1 A change is not significant (see § 21.101(b)(1));
2.2.2.2.2 An area, system, component, equipment, or appliance is not affected by the change (see § 21.101(b)(2));
03/11/16 AC 21.101-1B
2.2.2.2.3 Compliance with a later amendment for a significant change does not contribute materially to the level of safety (see § 21.101(b)(3)); or
2.2.2.2.4 Compliance with the latest amendment would be impractical (see § 21.101(b)(3)).
2.2.2.3 Earlier amendments may not precede the regulatory amendment level of the identified baseline product’s type certification basis and any requirement found in 14 CFR 23.2, 25.2, 27.2, and 29.2 or the applicable provision of part 26 related to the change.
2.2.2.4 Section 21.101(b)(1)(i) and (ii) pertain to design changes that meet the automatic criteria where the change is significant.
2.2.3 Section 21.101(c). Section 21.101(c) provides an exception from the requirements of § 21.101(a) for a change to certain aircraft with less than the specified maximum weight. If you apply for a type design change to an aircraft (other than rotorcraft) of 6,000 pounds or less maximum weight, or to a non-turbine powered rotorcraft of 3,000 pounds or less maximum weight, you can show that the changed product complies with the regulations incorporated by reference in the type certificate. You can also elect to comply or may be required to comply with the later regulations. See paragraph 4.1 of this AC for specific guidance on this provision.
2.2.4 Section 21.101(d). Section 21.101(d) provides for the use of special conditions, under § 21.16, when the proposed certification basis and any later regulations do not provide adequate standards to the proposed change because of a novel or unusual design feature.
2.2.5 Section 21.101(e). Section 21.101(e) prescribes the effective period that an application will remain valid for a change.
2.2.6 Section 21.101(f). Section 21.101(f) pertains to aircraft certificated in certain categories and special classes (e.g., gliders, airships, other nonconventional aircraft, and balloons certificated under 14 CFR part 31), including the engines and propellers installed on them, under the requirements of §§ 21.17(b), 21.24, 21.25, and 21.27 airworthiness requirements.
2.2.7 Section 21.101(g). Section 21.101(g) pertains to regulatory compliance of transport category airplanes with the applicable provisions of part 26 and/or corresponding later amendments to part 25. See paragraph 5.8 of this AC for additional details.
AC 21.101-1B › CHAPTER 3.
03/11/16 AC 21.101-1B
CHAPTER 3. PROCESS FOR ESTABLISHING THE CERTIFICATION BASIS FOR
CHANGED PRODUCTS
3.1 Overview.
3.1.1 The applicant and the FAA each have a responsibility under § 21.101(a) and (b). As an applicant for the certification of a type design change, you must show that the change and areas affected by the change comply with the latest applicable airworthiness requirements unless you propose exception(s) under § 21.101(b). If you are proposing exception(s), you should make a preliminary classification whether the change is “significant” or “not significant,” and propose an appropriate certification basis. The FAA is responsible for determining whether your classification of the change, and proposal for the certification basis, are consistent with the applicable rules and their interpretation. The FAA determination does not depend on whether the TC holder or applicant for an STC is originating the change. The certification basis can vary depending on the magnitude and scope of the change. The steps below present a streamlined approach for making this determination.
3.1.2 The tables in appendix A of this AC are examples of classifications of typical type design changes. See paragraph 3.6.3 of this chapter for instructions on how to use those tables.
3.1.3 If your proposed change is not in the examples provided in appendix A, you may use the following steps in conjunction with the flowchart in figure 3-1 of this AC to develop the appropriate certification basis for the type design change. For clarification, the design change discussed in the flowchart also includes areas affected by the design change pursuant to § 21.101. See paragraph 3.9.1 of this AC for guidance about affected areas.
CHAPTER 3. › Figure 3-1.
03/11/16 AC 21.101-1B
Figure 3-1. Developing a Proposed Certification Basis for a Changed Product
Pursuant to § 21.101
03/11/16 AC 21.101-1B
3.2 Step 1. Identify the Proposed Type Design Changes to an Aeronautical Product.
• Identify the type design you are changing (the baseline product).
• Identify the proposed change.
• Use high level descriptors.
3.2.1 Identify the Type Design You are Changing (the Baseline Product). Prior to describing the proposed change(s), it is important to clearly identify the specific type design configuration you are changing.
Note: For additional guidance on the baseline product, see paragraph 5.3 of this AC.
3.2.2 Identify the Proposed Change.
3.2.2.1 The purpose of this process step is to identify and describe the change to the aeronautical product. Changes to a product can include physical design changes and functional changes (e.g., operating envelope or performance changes). You must identify all changes and areas affected by the change, including those where you plan to use previously approved data. The FAA considers all of these changes and areas affected by the change part of the entire proposed type design and are considered as a whole in the classification of whether the proposed design change is substantial, significant, or not significant. The change can be a single change or a collection of changes. In addition to the proposed changes, consider the cumulative effect of previous relevant design changes incorporated since the last time the certification basis was upgraded. An applicant for a type design change must consider all previous relevant design changes and the amendment level of the certification basis used for these changes.
3.2.2.2 When you identify the proposed changes, consider previous relevant design changes that create a cumulative effect, as these may influence the decisions regarding the type of design change later in the process. By “previous relevant design changes,” the FAA means changes where effects accumulate, such as successive thrust increases, incremental weight increases, or sectional increases in fuselage length. You must account for any previous relevant design changes in the area affected by the proposed change that did not involve an upgrade of the certification basis in the proposed design change.
3.2.2.3 Example: An applicant proposes a 5 percent weight increase, but a previous 4 percent and another 3 percent weight increase was incorporated into this aircraft without upgrading the existing certification basis. In the current proposal for a 5 percent weight increase, the cumulative effects of the two previous weight increases that did not involve an upgrade of the certification basis will now be accounted for as an approximate 12 percent increase in weight. Note that the cumulative effects the applicant accounts
03/11/16 AC 21.101-1B
for are only those incremental increases since the last time the airworthiness requirements in the type certification basis applicable to the area affected by the proposed change were upgraded.
3.2.3 Use High Level Descriptors. To identify and describe the proposed changes to any aeronautical product, use a high level description of the design change that characterizes the intent of, or the reason for, the change. No complex technical details are necessary at this stage. For example, a proposal to increase maximum passenger-carrying capacity may require an addition of a fuselage plug, and as such, a “fuselage plug” becomes one possible high level description of this design change. Similarly, a thrust increase, a new or complete interior, an avionics system upgrade, or a passenger-to-cargo conversion are all high level descriptions that characterize typical changes to the aircraft, each driven by a specific goal, objective, or purpose.
3.2.4 Evolutionary changes that occur during the course of a certification program may require re-evaluation of the certification basis, and those changes that have influence at the product level may result in re-classification of the change.
3.3 Step 2. Verify the Proposed Type Design Change is Not Substantial.
3.3.1 Section 21.19 requires that you apply for a new TC for a changed product if the change in design, power, thrust, or weight is so extensive that a substantially complete investigation of compliance with the applicable regulations is required. A new TC could be required for either a single extensive change to a previously type certificated product or for a changed design derived through the cumulative effect of a series of design changes from a previously type certificated product.
3.3.2 A “substantially complete investigation” of compliance is required when most of the existing substantiation is not applicable to the changed product. In other words, you may consider the design change substantial if it is so extensive (making the product sufficiently different from its predecessor) that the design models, methodologies, and approaches used to demonstrate a previous compliance finding could not be used in a similarity argument. The FAA considers a change substantial when these approaches, models, or methodologies of how compliance was shown are not valid for the changed product.
3.3.3 If it is not initially clear that a new TC is required, appendix A of this AC provides some examples of substantial changes to aid in this classification. A substantial change requires application for a new TC. See §§ 21.17 and 21.19. If the change is not substantial, proceed to Step 3.
3.4 Step 3. Will you Use the Latest Standards? You can use the latest requirements for your proposed type design change and the area affected by the change. If you use the latest requirements, you will have met the intent
03/11/16 AC 21.101-1B
of § 21.101 and no further classification (significant or not significant) and justification is needed. Even though an applicant elects to use the latest certification requirements, the applicant will still be able to apply § 21.101 for future similar changes, and use the exceptions under § 21.101(b). However, the decision to comply with the latest requirements sets a new regulatory basis for all future related changes in the same affected area for that amended TC.
• If you are using the latest requirements, proceed to Step 6 (in paragraph 3.9 of this AC).
• If you are not using the latest requirements, proceed to Step 4 below.
3.5 Step 4. Arrange Changes into Related and Unrelated Groups.
3.5.1 You should now determine if any of the changes identified in Step 1 are related to each other. Related changes are those that cannot exist without another, are co-dependent, or a pre-requisite of another. For example, a need to carry more passengers could require the addition of a fuselage plug, which will result in a weight increase, and may necessitate a thrust increase. Thus, the fuselage plug, weight increase, and thrust increase are all related, high level changes needed to achieve the goal of carrying more passengers. A decision to upgrade the flightdeck to more modern avionics at the same time as these other design changes may be considered unrelated, as the avionics upgrade is not necessarily needed to carry more passengers (it has a separate purpose, likely just modernization). The proposed avionics upgrade would then be considered an unrelated (or a stand-alone) change. However, the simultaneous introduction of a new cabin interior is considered related since occupant safety considerations are impacted by a cabin length change. Even if a new cabin interior is not included in the product level change, the functional effect of the fuselage plug has implications on occupant safety (e.g., the dynamic environment in an emergency landing, emergency evacuation, etc.), and thus the cabin interior becomes an affected area. Figure 3-2 below illustrates the grouping of related and unrelated changes using the example of increasing the maximum number of passengers.
Figure 3-2 · page 16Picture of the page from the copy saved here
Note: If you plan changes in sequence over time, refer to the discussion on “sequential design changes” in paragraph 5.13 of this AC.
03/11/16 AC 21.101-1B
Figure 3-2. Related and Unrelated Changes for Example of Increasing the Maximum
Number of Passengers
The Aeronautical Product
CHAPTER 3. › Figure 3-2.
Affected Area
Affected Area
Grouping of Related Changes
(significant change)
Thrust Increase
(physical and performance changes)
MTOW Increase
(physical and performance changes)
Fuselage Stretch (physical change)
Changed Area
Comprehensive Flightdeck Upgrade
(typically, a stand-alone significant physical change)
Not Affected
Area
3.5.2 Once you organize the change(s) into groupings of those that are related and those that are unrelated (or stand-alone), proceed to Step 5 below.
3.6 Step 5. Is Each Related or Unrelated Group a Significant Change?
3.6.1 The applicant is responsible for proposing the classification of groups of related design changes or unrelated design changes as significant or not significant. Significant changes are product level changes that could result from an accumulation of changes, or occur through a single significant change that makes the changed product distinct from its baseline product. The grouping of related and unrelated changes is particularly relevant to the FAA’s significant Yes/No decision (§ 21.101(b)(1)) described in Step 5 of figure 3-1. The FAA evaluates each group of related changes and each unrelated (stand-alone) change on its own merit for significance. Thus, there may be as many evaluations for significance as there are groupings of related and unrelated changes. Step 1 of figure 3-1 explains the accumulation of changes that you must consider.
03/11/16 AC 21.101-1B
Additionally, § 21.101(b)(1) defines a design change as significant when at least one of three automatic criteria applies:
3.6.1.1 Changes where the General Configuration is Not Retained (Significant Change to General Configuration). A change to the general configuration at the product level is one that distinguishes the resulting product from other product models, for example, performance or interchangeability of major components. Typically, for these changes, an applicant will designate a new product model, although this is not required. For examples, see appendix A of this AC.
3.6.1.2 Changes where the Principles of Construction are Not Retained (Significant Change to Principles of Construction). A change at the product level to the materials and/or construction methods that affects the overall product’s operating characteristics or inherent strength and would require extensive reinvestigation to show compliance. For examples, see appendix A of this AC.
3.6.1.3 Product Level Changes that Invalidate the Assumptions used for Certification of the Baseline Product. Examples include—
• Change of an aircraft from an unpressurized to pressurized fuselage,
• Change of operation of a fixed wing aircraft from land-based to water-based, and
• Operating envelope expansions that are outside the approved design parameters and capabilities.
For additional examples, see appendix A of this AC.
3.6.2 The above criteria are used to determine if each change grouping and each stand-alone change is significant. These three criteria are assessed at the product level. In applying the automatic criteria and the examples in appendix A of this AC, you should focus on the design change and how it impacts the existing product (including performance, operating envelope, etc.). A design change cannot be classified or re-classified as a significant change on the basis of the importance of a later amendment level.
3.6.3 Appendix A of this AC includes tables of typical changes (examples) for small airplanes, transport airplanes, rotorcraft, engines, and propellers that meet the criteria for a significant design change. The appendix also includes tables of typical design changes that the FAA classifies as not significant. The tables can be used in one of two ways—
3.6.3.1 To identify the classification of a proposed design change listed in the table, or
03/11/16 AC 21.101-1B
3.6.3.2 In conjunction with the three automatic criteria, to help classify a proposed design change not listed in the table by comparison to determinations made for changes with similar type and magnitude.
3.6.4 In many cases, a significant change may involve more than one of these criteria and will be obvious and distinct from other product improvements or production changes. There could be cases where a change to a single area, system, component, or appliance may not result in a product level change. There could also be other cases where the change to a single system or component might result in a significant change due to its effect on the product overall. Examples may include the addition of winglets or leading edge slats, or a change in primary flight controls to a fly-by-wire system.
3.6.5 If an unrelated (stand-alone) change or a grouping of related changes is classified as—
3.6.5.1 Significant (§ 21.101(a)): You must comply with the latest airworthiness standards for certification of the design change and areas affected by change, unless you justify use of one of the exceptions provided in § 21.101(b)(2) or (3) to show compliance with earlier amendment(s). The final certification basis may consist of a combination of the requirements recorded in the certification basis ranging from the original aircraft certification basis to the most current regulatory amendments.
3.6.5.2 Not Significant (§ 21.101(b)(1)): You may comply with the existing certification basis unless the standards in the proposed certification basis are deemed inadequate. In cases where the existing certification basis is inadequate or no regulatory standards exist, later requirements and/or special conditions will be required. See paragraph 3.11 of this AC for a detailed discussion.
3.6.6 A new model designation to a changed product is not necessarily indicative that the design change is significant under § 21.101. Conversely, retaining the existing model designation does not mean that the design change is not significant. Significance is determined by the magnitude of the type design change.
3.6.7 The FAA determines the final classification of whether a design change is significant or not significant. To assist you in your assessment, the FAA has predetermined the classification of several typical design changes that you can use for reference, and these examples are listed in appendix A of this AC.
3.6.8 At this point, the determination of significant or not significant for each of the groupings of related changes and each stand-alone change is completed. For significant changes, if you propose to comply with an earlier requirement, use the procedure outlined in paragraph 3.7 below. For changes identified as not significant, see paragraph 3.8 below.
03/11/16 AC 21.101-1B
3.7 Proposing an Amendment Level for a Significant Change.
3.7.1 If the classification of the group of related changes is significant, all areas, systems, components, parts, or appliances affected by the change must comply with the airworthiness standards at the amendment level in effect on the date of application for the change. You can justify use of one of the exceptions in § 21.101(b)(2) and (3) to comply with an earlier amendment but no earlier than the existing certification basis. You must comply with any retroactive requirement found in §§ 23.2, 25.2, 27.2, 29.2 applicable on the date of the application for the change. See paragraphs 3.9 and 3.10 of this AC.
3.7.2 For transport category airplanes only, § 21.101(g) requires that you comply with any applicable provision of part 26 (related to the change), which is applicable on the date of the application for the change, unless you elected or were required to comply with later corresponding part 25 requirements.
3.7.3 The final certification basis may combine latest, earlier (intermediate), and existing regulations, but cannot contain regulations preceding the existing certification basis.
3.8 Proposing an Amendment Level for a Not Significant Change.
3.8.1 When the FAA classifies the type design change as not significant, the rule allows compliance with earlier amendments but not prior to the existing certification basis. Within this limit, the applicant may propose an amendment level for each certification standard for the affected area. However, you should be aware that the FAA will review your proposal for the type certification basis to ensure that the certification basis is adequate for the proposed change under Step 8. (See paragraph 3.11 of this AC.) You must also comply with the retroactive requirements found in §§ 23.2, 25.2, 27.2, 29.2, applicable on the date of the application for the change.
3.8.2 For transport category airplanes only, § 21.101(g) also requires that you comply with any applicable provision of part 26 (related to the change), which is applicable on the date of the application for the change, unless you elected or were required to comply with later corresponding part 25 requirements. You may comply with a specific airworthiness requirement or a subset of airworthiness requirements at later amendments. In such a case, any other airworthiness requirements that are directly related should be included in the certification basis for the change.
3.9 Step 6. Prepare your Proposed Certification Basis List. As part of preparing your proposed certification basis list, you must identify any areas, systems, components, equipment, or appliances of the product that are affected by the design change and the corresponding regulatory standards associated with these areas. For each group, you must assess the physical and/or functional effects of the change on any areas, systems, components, equipment, or appliances of the product. The characteristics affected by the change are not only physical changes, but also functional
CHAPTER 3. › Figure 3-3. Affected Areas versus Not Affected Areas
03/11/16 AC 21.101-1B
changes brought about by the physical changes. Examples of physical aspects are structures, systems, components, equipment, appliances, and software in combination with the affected hardware. Examples of functional characteristics are performance, handling qualities, aeroelastic characteristics, and emergency egress. The intent is to encompass all aspects where there is a need for re-evaluation, that is, where the substantiation presented for the product you are changing should be updated or rewritten. Appendix H of this AC contains two examples of how to document a proposed certification basis list.
3.9.1 An area affected by the change is any system, component, part, or appliance of the aeronautical product that you physically and/or functionally change. Figure 3-3 of this AC illustrates concepts of physical and functional changes of an affected area. Appendix C of this AC contains a method used to define the change and areas affected by the change. This appendix is meant to assist you when you propose a large, complex design change. For a type design change, it is important that you properly assess the effects of such change on any areas, systems, components, equipment, or appliances of the product because areas that have not been physically changed may still be considered part of the affected area. If a new compliance finding is required, regardless of its amendment level, it is an affected area.
Figure 3-3. Affected Areas versus Not Affected Areas
Physical Change
Functional Change
Not Affected Area
Significant Change and
Area Affected by the
Significant Change
The Aeronautical Product
03/11/16 AC 21.101-1B
Figure 3-3 · page 20Picture of the page from the copy saved here
3.9.2 An area not affected by a change can remain at the existing certification basis, provided you present to the FAA acceptable justification that the area is not affected.
3.9.3 For sample questions to assist in determining affected areas, see paragraph D.1 of appendix D of this AC.
3.9.4 Consider the following aspects of a type design change:
3.9.4.1 Physical Aspects. The physical aspects include direct changes to structures, systems, equipment, components, and appliances, and may include software/airborne electronic hardware changes and the resulting effect on systems functions.
3.9.4.2 Performance/Functional Characteristics. The less obvious aspect of the word “areas” covers general characteristics of the type certificated product, such as performance features, handling qualities, emergency egress, structural integrity (including load carrying), aeroelastic characteristics, or crashworthiness. A product level change may affect these characteristics. For example, adding a fuselage plug could affect performance and handling qualities, and thus regulations associated with these aspects would be considered part of the affected area. Another example is the addition of a fuel tank and new fuel conditioning unit. This change affects the fuel transfer and fuel quantity indication system resulting in the airplane’s unchanged fuel tanks being affected. Thus, the entire fuel system (changed and unchanged areas) may become part of the affected area due to the change in functional characteristics. Another example is changing turbine engine ratings and operating limitations affecting the engine rotors’ life limits.
3.9.5 All areas affected by the proposed design change must comply with the latest requirements, unless you show that demonstrating compliance with the latest amendment of a requirement would not contribute materially to the level of safety or would be impractical. Step 7 below provides further explanation.
3.9.6 The applicant should document the change and area affected by the change using high level descriptors along with the applicable regulations and their associated amendment levels. The applicant proposes this change in certification basis that the FAA will consider for documentation in the type certificate data sheet (TCDS) or STC, if they are different from that recorded for the baseline product in the TCDS.
3.10 Step 7. Do the Latest Requirements Contribute Materially to the Level of Safety and are They Practical? Pursuant to § 21.101(a), compliance with the latest airworthiness standards is required. However, exceptions may be allowed pursuant to § 21.101(b)(3). The applicant must provide justification to support the rationale for the application of earlier amendments
03/11/16 AC 21.101-1B
for areas affected by a significant change to document that compliance with later requirements in these areas would not contribute materially to the level of safety or would be impractical. Such justification should address all the aspects of the area, system, component, equipment, or appliance affected by the significant change. See paragraphs 3.10.1 and 3.10.1.4 of this AC.
3.10.1 Do the Latest Requirements Contribute Materially to the Level of Safety? You could consider compliance with the latest requirements to “not contribute materially to the level of safety” if the existing type design and/or relevant experience demonstrates a level of safety comparable to that provided by the latest requirements. In cases where design features provide a level of safety greater than the existing certification basis, you may use acceptable data, such as service experience to establish the effectiveness of those design features at mitigating the specific hazards by a later amendment. You must provide sufficient justification to allow the FAA to make this determination. An acceptable means of compliance is described in appendix E of this AC. Justification is sufficient when it provides a summary of the evaluation that supports the determination using an agreed evaluation method such as that in appendix E of this AC. This exception could be applicable in the situations described in the paragraphs below.
Note: Compliance with later requirements is not required where the amendment is of an administrative nature and made only to correct inconsequential errors or omissions, consolidate text, or clarify an existing requirement.
3.10.1.1 Improved Design Features. Design features that exceed the existing certification basis requirements, but do not meet the latest requirements, can be used as a basis for granting an exception under § 21.101(b)(3) since complying with the latest amendment of the requirements would not contribute materially to the level of safety of the product. If the FAA accepts these design features as justification for an exception, you must incorporate them in the amended type design configuration and record them, where necessary, in the certification basis. The description of the design feature would be provided in the TCDS or STC at a level that allows the design feature to be maintained, but does not contain proprietary information. For example, an applicant proposes to install winglets on a part 25 airplane, and part of the design involves adding a small number of new wing fuel tank fasteners. Assuming that the latest applicable amendment of § 25.981 is Amendment 25-102, which requires structural lightning protection, the applicant could propose an exception from these latest structural lightning protection requirements because the design change uses new wing fuel tank fasteners with cap seals installed. The cap seal is a design feature that exceeds the requirement of § 25.981 at a previous amendment level, but does not meet the latest Amendment 25-102. If the applicant can successfully substantiate that compliance with Amendment 25-102 would not materially increase the level of safety of the changed product, then this
03/11/16 AC 21.101-1B
design feature can be accepted as an exception to compliance with the latest amendment.
3.10.1.2 Consistency of Design. This provision gives the opportunity to consider the consistency of design. For example, when a small fuselage plug is added, additional seats and overhead bins are likely to be installed, and the lower cargo hold extended. These components may be identical to the existing components. The level of safety may not materially increase by applying the latest requirements in the area of the fuselage plug. Compliance of the new areas with the existing certification basis may be acceptable.
3.10.1.3 Service Experience.
3.10.1.3.1 Relevant service experience, such as experience based on fleet performance or utilization over time (relevant flight hours or cycles), is one way of showing that the level of safety will not materially increase by applying the latest amendment, so the use of earlier requirements could be appropriate. Appendix F of this AC provides additional guidance on the use of service experience, along with examples.
3.10.1.3.2 When establishing the highest practicable level of safety for a changed product, the FAA has determined that it is appropriate to assess the service history of a product, as well as the later airworthiness standards. It makes little sense to mandate changes to well understood designs, whose service experience has been acceptable, merely to comply with new standards. The clear exception to this premise is if the new standards were issued to address a deficiency in the design in question, or if the service experience is not applicable to the new standards.
3.10.1.3.3 There may be cases for rotorcraft and small airplanes where relevant data may not be sufficient or not available at all because of the low utilization and insufficient amount and type of data available. In such cases, other service history information may provide sufficient data to justify the use of earlier requirements, such as warranty, repair, and parts usage data; accident, incident, and service difficulty reports; service bulletins; airworthiness directives; or other pertinent and sufficient data collected by the manufacturers, authorities, or other entities.
3.10.1.3.4 The FAA will determine if proposed service experience levels necessary to demonstrate the appropriate level of safety as they relate to the proposed design change is acceptable.
3.10.1.4 Secondary Changes.
3.10.1.4.1 The design change proposed by the applicant can consist of physical and/or functional changes to the product. See figure 3-4 below. There may
CHAPTER 3. › Figure 3-4. Design Change Affected Areas with Secondary Changes
03/11/16 AC 21.101-1B
be aspects of the existing type design of the product that the applicant may not be proposing to change directly, but that are affected by the overall design change. For example, changing an airframe’s structure, such as adding a cargo door in one location, may affect the frame or floor loading in another area. Further, upgrading engines with new performance capabilities could require additional showing of compliance for minimum control speeds and airplane performance requirements. For many years, the FAA has required applicants to consider these effects, this practice is unchanged under the procedures of § 21.101.
Figure 3-4. Design Change Affected Areas with Secondary Changes
Physical Change
Functional Change
Not Affected Area
Significant Change and
Area Affected by the
Significant Change
The Aeronautical Product
Secondary
Changes
Figure 3-4 · page 24Picture of the page from the copy saved here
3.10.1.4.2 For each design change, it is important that the effects of the change on other systems, components, equipment, or appliances of the product are properly identified and assessed. The intent is to encompass all aspects where there is a need for re-evaluation, that is, where the substantiation presented for the product being changed should be reviewed, updated, or rewritten.
03/11/16 AC 21.101-1B
3.10.1.4.3 In assessing the areas affected by the design change, it may be helpful to identify secondary changes. A secondary change is a change in physical and/or functional aspects that is part of but consequential to a significant physical design change, whose only purpose is to restore, and not add or increase, existing functionality or capacity. The term “consequential” is intended to refer to—
• A change that would not have been made by itself; it achieves no purpose on its own.
• A change that has no effect on the existing functionality or capacity of areas, systems, structures, components, parts, or appliances affected by the design change.
• A change that would not create the need for: (1) new limitations or affect existing limitations; (2) a new airplane flight manual (AFM) or instructions for continued airworthiness (ICA) or a change to the AFM or ICA; or (3) special conditions, equivalent safety findings, or exemptions.
3.10.1.4.4 A secondary change is not required to comply with the latest requirements because it is considered “not contributing materially to the level of safety” and, therefore, eligible for an exception under § 21.101. Determining whether a change meets the description for a secondary change, and thus eligible for an exception, should be straightforward. Hence, the substantiation or justification need only be minimal. If this determination is not straightforward, then your proposed change is not a secondary change.
3.10.1.4.5 In some cases, a secondary area of change that restores functionality may in fact contribute materially to the level of safety by meeting a later amendment. If this is the case, it is not considered a secondary change.
3.10.2 Are the Latest Requirements Practical? The intent of § 21.101 is to enhance safety by applying the latest airworthiness standards to the greatest extent practicable. The concepts of contributing materially and practicality are linked. If compliance with the latest airworthiness standards does contribute materially to the level of safety, then the applicant may assess incremental costs to see if it is commensurate with the increase in safety. The additional resource requirements could include those arising from design changes required for compliance and the effort required to demonstrate compliance, but excludes resource expenditures for prior product changes. The cost of changing compliance documentation and/or drawings is not an acceptable reason for an exception.
3.10.2.1 Support your position that compliance is impractical with substantiating data and analyses. While evaluating your position and your substantiating data regarding impracticality, the FAA may consider other factors (e.g., the costs and safety benefits for a comparable new design).
03/11/16 AC 21.101-1B
3.10.2.2 A review of transport category projects showed that, in certain cases where the FAA allowed an earlier amendment of applicable requirements, the applicants made design changes that nearly complied with the latest amendments. In these cases, the applicants successfully demonstrated that full compliance would require a substantial increase in the outlay or expenditure of resources with a very small increase in the level of safety. These design features can be used as a basis for granting an exception under § 21.101(b)(3) on the basis of “impracticality.”
3.10.2.3 Appendix E of this AC provides additional guidance and examples for evaluating the impracticality of applying the latest requirements to a changed product for which compliance with the latest requirements would contribute materially to the level of safety of the product.
3.10.2.3.1 The exception of impracticality is a qualitative and quantitative cost/safety benefit assessment for which it is difficult to specify clear criteria. Experience to date with applicants has shown that justification of impracticality is more feasible when both the applicant and FAA agree at an earlier discussion that the effort (in terms of cost, changes in manufacturing, etc.) required to comply would not be commensurate with a small incremental safety gain. This would be clear even without the need to perform any detailed cost/safety benefit analysis (although an applicant could always use cost analysis to support an appropriate amendment level). However, there should be enough detail in the applicant’s rationale to justify the exception.
Note: An applicant should not base the impractical exception on the size of the applicant’s company or their financial resources. The applicant must evaluate the costs to comply with a later amendment against the safety benefit of complying with the later amendment.
3.10.2.3.2 For example, a complex redesign of an area of the baseline aircraft may be required to comply with a new requirement, and that redesign may make the changed product uncommon with respect to design and manufacturing processes from the existing family of models. Relevant service experience of the existing fleet of the baseline aircraft family would be required to show that there has not been a history of problems associated with the hazard that the new amendment in question was meant to address. In this way, the incremental cost/impact to the applicant is onerous, and the incremental safety benefit realized by complying with the later amendment would be minimal. This would be justified with a demonstrated acceptable service experience in relation to the hazard that the new rule addresses.
03/11/16 AC 21.101-1B
3.11 Step 8. Ensure Proposed Certification Basis is Adequate. The FAA considers a proposed certification basis for any design change (whether it is significant or not significant) to be adequate when—
• The airworthiness standards provide an appropriate level of safety for the intended change, and
• The change and the areas affected by the change do not result in unsafe design features or characteristics for the intended use.
3.11.1 For a change that contains new design features that are novel and unusual for which there are no later applicable airworthiness requirements at a later amendment level, the FAA will designate special conditions pursuant to § 21.16. The FAA will impose later airworthiness standards that contain adequate or appropriate safety standards for this feature, if they exist, in lieu of special conditions. An example is adding a flight critical system such as an electronic air data display on a part 25 airplane whose existing certification basis does not have lightning and high intensity radiated fields (HIRF) protection requirements. In this case, the FAA will require compliance with the regulations for lightning and HIRF protection, even though the FAA determined the change is not significant.
3.11.2 For new design features or characteristics that may pose a potential unsafe condition for which there are no later applicable airworthiness requirements, new requirements may be required to address § 21.21(b)(2).
3.11.3 In cases where inadequate or no airworthiness standards exist for the change in the existing type certification basis but adequate standards exist in a later amendment of the applicable airworthiness code, the later amendment will be made part of the type certification basis to ensure adequacy of its certification basis.
3.11.4 The FAA determines the final certification basis for a product design change. This may consist of a combination of those airworthiness standards ranging from the existing certification basis of the baseline product to the latest amendments and special conditions.
AC 21.101-1B › CHAPTER 4. EXCEPTED PRODUCTS UNDER § 21.101(C)
03/11/16 AC 21.101-1B
CHAPTER 4. EXCEPTED PRODUCTS UNDER § 21.101(C)
4.1 Excepted Products. For excepted products as defined in paragraph 4.1.1 below, the starting point for regulatory analysis is the existing certification basis for the baseline product.
4.1.1 Section 21.101(c) provides an exception to § 21.101(a) compliance with the latest requirements for aircraft (other than rotorcraft) of 6,000 pounds or less maximum weight, or to a non-turbine rotorcraft of 3,000 pounds or less maximum weight. In these cases, the applicant may elect to comply with the existing certification basis. However, the applicant has the option of applying later appropriate regulations. Special classes of aircraft—including gliders, airships, and primary category—are addressed in § 21.101(f), and not in § 21.101(c).
4.1.2 If the FAA finds that the change is significant in an area, the FAA may require the applicant to comply with a later regulation and any regulation the FAA finds is directly related. Starting with the existing certification basis, the FAA will progress through each later regulation to determine the amendment appropriate for the change. However, if an applicant proposes, and the FAA finds, that complying with the later amendment or regulation would not contribute materially to the level of safety of the changed product or would be impractical, the FAA may allow the applicant to comply with an earlier amendment appropriate for the proposed design change. The amendment may not be earlier than the existing certification basis. For excepted products, changes that meet one of the following criteria, in the area of change, are automatically considered significant if—
4.1.2.1 The general configuration or the principles of construction are not retained.
4.1.2.2 The assumptions used for certification of the area to be changed do not remain valid.
4.1.2.3 The change contains new features (not foreseen in the existing certification basis and for which appropriate later regulations exist). In this case, the FAA will designate the applicable airworthiness requirements, starting with the existing certification basis and progressing to the most appropriate later amendment level for the change.
4.1.2.4 The change contains a novel or unusual design feature. In this case, the FAA will designate the applicable special conditions appropriate for the change, pursuant to § 21.101(d).
4.1.3 The exception for products under § 21.101(c) applies to the aircraft only. Design changes to engines and propellers installed on these excepted aircraft are assessed as separate type certificated products using § 21.101(a) and (b).
AC 21.101-1B › CHAPTER 5. OTHER CONSIDERATIONS
03/11/16 AC 21.101-1B
CHAPTER 5. OTHER CONSIDERATIONS
5.1 Design-Related Operating Requirements. Some rules in other 14 CFR parts (e.g., parts 91, 121, 125, and 135) impose airworthiness standards that are not required for issuance of a TC or STC. If not already included in the certification basis, any such applicable airworthiness standards may be added to the type certification basis by mutual agreement between the applicant and the FAA. The benefit of adding these airworthiness standards to the type certification basis is to increase awareness of these standards, imposed by other 14 CFR parts, during design certification and future modifications to the airplane. The use of exceptions under § 21.101 is not intended to alleviate or preclude compliance with operating regulations.
5.2 FAA Policy. Once the certification basis has been established, the exceptions of § 21.101 are not applicable in determining which policy (e.g., ACs and policy statements) applies to the design change. Guidance on the use of policy is found in FAA Order 8110.4C, Type Certification, and Order 8110.48A, How to Establish the Certification Basis for Changed Aeronautical Products. In general, you should use the latest FAA policy in effect at the date of application. However, there might be cases where policy may differ depending on the amendment level of the rule (i.e., the intent of the regulation may be different). It is acceptable to use another means of compliance, provided it is agreed upon by the FAA. This is typically documented via an issue paper.
5.3 A Baseline Product Consists of One Unique Type Design Configuration. As mentioned in paragraph 3.2.1 of this AC, it is important to clearly identify the type design configuration to be changed. The baseline for a changed product consists of one unique type design configuration. This unique type design configuration is an approved product configuration that can be manufactured at one time or may consist of multiple approvals over time (e.g., airplane model with an approved STC incorporated). The applicant should identify the specific product configuration that will be modified. The FAA does not require an applicant to assign a new model name for a changed product. Therefore, there are vastly different changed products with the same airplane model name, and there are changed products with minimal differences that have different model names. Since the assignment of a model name is based solely on an applicant business decision, the identification of the baseline product, for the purposes of § 21.101, is one unique type design configuration, as mentioned above.
Note: The type design configuration, for this purpose, could be based on a currently approved configuration or based on a proposed future configuration that is expected to be approved at a later date but prior to the proposed changed product.
03/11/16 AC 21.101-1B
5.4 Predecessor Regulations. The airworthiness requirements in effect on the date of application are in parts 21, 23, 25, 27, 29, 31, 33, and 35. Consequently, when electing to comply with later requirements, the predecessor regulations (i.e., Civil Air Regulations (CARs)) are not considered in effect on the date of application. Predecessor regulations are not recognized under § 21.101(a), but may be allowed under § 21.101(b), (c), and (f).When choosing the amendment level of a regulation, all related regulations associated with that amendment level would have to be included.
5.5 Special Conditions, § 21.101(d). Section 21.101(d) allows for the application of special conditions, or for changes to existing special conditions, to address the changed designs where the proposed certification basis does not provide adequate standards for an area, system, component, equipment, or appliance related to the change. The objective is to achieve a level of safety consistent with that provided for other areas, systems, components, equipment, or appliances affected by the change by the other requirements of the proposed certification basis. The application of special conditions to a design change is not, in itself, a reason to classify it as either a substantial change or a significant change. When the change is significant with earlier requirements allowed through exceptions, or not significant, the level of safety intended by the special conditions must be consistent with the agreed certification basis.
5.6 Effective Period for an Application to Change a Type Certificate, § 21.101(e). According to § 21.101(e), an application for, or a change to, a TC for transport category aircraft is effective for five years from the date of application, and an application for a change to any other type certificate is effective for three years. The FAA intended this to ensure that the certification basis for the changed product is as current as practicable.
5.6.1 If the FAA has not approved a design change, or if it is clear that the FAA will not approve the change, within the time limit, the applicant may do either of the following: (1) file for a new application, or (2) file for an extension to the original application.
5.6.2 When filing an extension, the applicant must choose a completion date, then apply the applicable effectivity from § 21.101(e) to determine an effective application date. The effective application date must not precede the original date of application for the proposed design change and must not be later than the filing date for an extension.
5.6.3 If you request an extension to the application date, and the product change is significant, a new certification basis is required. The new certification basis requires the additional latest regulations effective through the new application extension date. However, the applicant may use earlier regulations by documenting justification that the latest regulations for the change would not contribute materially to the level of safety or would be impractical.
03/11/16 AC 21.101-1B
5.6.4 If the product change is not significant, you may continue to use the existing certification basis for product certification. However, if you make additional design changes to the product, and the FAA finds the existing certification basis for the change inadequate, the new certification basis will require later appropriate standards.
5.7 Other Category Aircraft, § 21.101(f). For aircraft type certificated under §§ 21.17(b), 21.24, 21.25, and 21.27, the certification basis for the changed product consists of the amendment levels of the applicable regulations that the FAA finds appropriate for the change in effect on the date of application for the change. When selecting a certification basis for a change, you can propose compliance to an earlier amendment using the provisions of § 21.101(b). The exceptions in § 21.101(c) do not apply to categories of products defined in § 21.101(f).
5.7.1 Special Classes Aircraft. For special classes of aircraft (e.g., gliders, airships, etc.) including any installed engines and propellers certificated pursuant to § 21.17(b), the applicable requirements are portions of those other airworthiness requirements in parts 23, 25, 27, 29, 31, 33, and 35 that the FAA finds appropriate for the aircraft and applicable to the specific type design, or such airworthiness criteria that the FAA finds an equivalent level of safety to those parts.
5.7.2 Primary Category Aircraft. For primary category aircraft certificated under § 21.24, the applicable airworthiness requirements are in parts 23, 27, 31, 33, and 35, or such other requirements the FAA finds appropriate. These requirements must be applicable to the specific design and intended use of the aircraft and provide a level of safety acceptable to the FAA.
5.7.3 Restricted Category Aircraft. For aircraft certificated in the restricted category under § 21.25(a)(1), the application of the latest regulations typically would be considered not to contribute materially to the level of safety or be practical for its intended use. However, if the airworthiness regulations applicable to the aircraft at the time the TC was issued do not provide an adequate level of safety for the design change, the application of later regulations will be required.
5.7.3.1 Features of the changed product that are “novel” or “unusual” to the original certificated restricted category product may be assessed against a later requirement that addresses the feature. In this case, the applicable airworthiness requirements in effect at the time of the existing restricted category TC may be viewed as a starting point, with subsequent amendments being examined, if necessary, to arrive at a requirement that provides an appropriate level of safety.
5.7.3.2 For the installation of turbo-propeller engines instead of reciprocating engines (either in a restricted category aircraft that was originally
03/11/16 AC 21.101-1B
certificated based on satisfactory military service experience or in a restricted category aircraft for which the original certification basis did not contain regulations for turbine engine installations), later amendments will be used to provide an appropriate level of safety for its intended operation. In addition, any change to the aircraft must be shown to be “safe for its intended use” as required by § 21.25. See Order 8110.56A, Restricted Category Type Certification, for additional details.
5.7.3.3 If the design change includes a new special purpose, it may require a re-evaluation of the regulations for certification. See Order 8110.56A, Chapter 3.
5.7.4 Military Aircraft Designs. Aircraft type certificated in the restricted category under § 21.25(a)(2) are accepted on the basis of the U.S. military use and other eligibility factors, instead of showing compliance with airworthiness standards in 14 CFR Chapter 1. (See Order 8110.56, Chapter 4, for additional details.) Many of these aircraft were not certificated to airworthiness standards; therefore, any modifications made to the military configuration must meet an equivalent civil certification basis derived from the airworthiness regulations contained in 14 CFR. This baseline certification basis is the airworthiness regulations (i.e., parts 23, 25, 27, 29, 33, or 35, or CARs, as appropriate) that were in effect on the date that the first military model was accepted for operational use by the U.S. Armed Forces. Section 21.101(f) requires the application of the latest amendments to significant changes to these products. However, since the latest amendments may not be appropriate for the aircraft’s intended use, earlier regulations are acceptable. They cannot predate the equivalent certification basis. If these regulations do not include airworthiness standards applicable to the change, later regulations appropriate to the product category will be applied. In addition, any design change to the aircraft must be shown to be “safe for its intended use” as required by § 21.25. See Order 8110.56A for additional details.
5.7.5 Surplus Military Aircraft. Aircraft type certificated under § 21.27 are entitled to a TC in the normal, utility, acrobatic, commuter, or transport category. These aircraft were designed and constructed in the United States, accepted for operational use, and declared surplus by the U.S. Armed Forces. These aircraft may be counterparts, and are considered equivalent, to the previously civil certificated aircraft. Product changes or modifications to these aircraft are certificated in the same manner as their civil counterparts.
5.7.6 Limited Category Aircraft. Limited category aircraft are surplus military aircraft, mostly from World War II, that were type certificated under CAR part 9 for use other than air transport. These aircraft are not permitted to carry persons or property for hire, and were accepted based on their previous military qualifications. A change to aircraft not supported by the military service history must comply with appropriate airworthiness standards. The level of safety associated with earlier standards may be acceptable for limited category aircraft.
03/11/16 AC 21.101-1B
5.8 Clarification of § 21.101(g), Part 26 Requirements.
5.8.1 Part 26 establishes requirements for support of continued airworthiness of and safety for transport category airplanes. The applicant must show compliance with each applicable provision of part 26, unless the applicant has elected or was required to comply with a corresponding amendment to part 25 that was issued on or after the date of the applicable part 26 provision. Section 21.101(g) does not allow an applicant to use an exception under § 21.101(b) for relief from complying with the applicable provisions of part 26.
5.8.2 The language in § 21.101(g) also recognizes that future part 25 amendments will be issued after the requirements in part 26 are established. Consequently, an applicant may be required to comply with a later part 25 amendment. Section 21.101(g) does not contain exception provisions for reverting to earlier part 26 requirements. However, under § 21.101(b) instead of complying with a later part 25 requirement, an applicant may be allowed to comply with an earlier part 26 or earlier part 25 requirement if justification is provided.
5.9 Documentation.
5.9.1 Documenting the Proposal. In order to efficiently determine and agree upon a certification basis with the FAA, the following information is useful to understand your position:
• The current certification basis of the product you are changing, including amendment level.
• The amendment level of all the applicable airworthiness requirements at the date of application.
• Your proposed certification basis, including amendment levels.
• Description of the affected area.
• If you propose a certification basis that includes amendment levels earlier than what was in effect at the date of application, include the exception as outlined in § 21.101(b) and your justification if needed.
Please see appendix H for examples of optional tools you can use to document your proposed certification basis.
5.9.2 Documenting the Significant/Not Significant Decision.
5.9.2.1 The FAA determines whether the design changes are significant or not significant, and this decision is documented on the Certification Project Notification according to FAA Order 8110.115, Certification Project Initiation and Certification Project Notification. However, the FAA provides an optional decision record for the applicant to make a predetermination to facilitate the FAA decision. This form is provided in
03/11/16 AC 21.101-1B
appendix G of this AC and follows the flowchart in figure 3-1 of this AC. If used, you should submit it along with the certification plan.
5.9.2.2 Design changes that are determined to be significant changes under § 21.101, the exceptions, and agreement of affected and unaffected areas is typically documented through the G-1 issue paper process. An example tool is provided in appendix H of this AC.
5.9.3 Documenting the Certification Basis.
5.9.3.1 The FAA will amend the certification basis for all design changes that result in a revision to the product’s certification basis on the amended TCDS or STC. The FAA will document the resulting certification basis because it is part of the compliance record required by FAA Order 8110.4C. For further information on documenting the certification basis, see FAA Order 8110.48A.
5.9.3.2 The FAA will document the certification basis of each product model on all STCs, including Approved Model List STCs.
5.10 Incorporation of STCs into the Type Design. The incorporation of STCs into the product type design may generate an additional major change when that change is needed to account for incompatibility between several STCs that were initially not intended to be applied concurrently.
5.10.1 If the incorporation of the STC(s) does not generate an additional major change, the incorporation is not evaluated pursuant to § 21.101. The existing certification basis should be updated to include the later amendments of the STC(s) being incorporated.
5.10.2 If the incorporation of the STC(s) generates an additional major change, the change must be evaluated pursuant to § 21.101, and the existing certification basis should be updated to include the amendments resulting from the application of § 21.101.
5.11 Removing Design Changes. Approved design changes may be removed after incorporation in an aeronautical product. These design changes will most commonly occur via an STC or service bulletin kit.
5.11.1 You should identify a product change that you intend at its inception to be removable as such, and you should develop instructions for its removal during the initial certification. The FAA will document the certification basis for both the installed and removed configuration separately on the TCDS or STC.
5.11.2 If specific removal instructions and a certification basis corresponding to the removed condition are not established at the time of the initial product change certification, the removal of design changes or portions of those changes may constitute a significant
03/11/16 AC 21.101-1B
change to type design. A separate STC or amended TC may be required to remove modifications and the resulting certification basis established for the changed product.
5.12 The Certification Basis is Part of the Design Change. A new design change may be installed in a product in production or via a service bulletin or STC. In terms of § 21.101, each of the approved design changes has its own basis of certification. If an applicant chooses to remove an approved installation (e.g., interior installation, avionics equipment) and install a new installation, a new certification basis may be required for the new installation, depending on whether the change associated with the new installation is considered significant compared to the baseline configuration that the applicant chooses. If the new installation is a not significant change, the unmodified product’s certification basis may be used (not the previous installation certification basis), provided the certification basis is adequate. For example, a transport category airplane is certified as a “green” configuration. The airplane certification basis does not include § 25.562 if it was manufactured prior to October 28, 2009. An interior is installed under an STC, and the applicant elects to include § 25.562 (dynamic seats) in the certification basis to meet specific operational requirements. At a later date, the airplane is sold to a non-part 121 operator (i.e., does not have the same operating requirements). A new interior is installed; there will be no requirement for § 25.562 to be included in the new certification basis.
5.13 Sequential Design Changes—Cumulative Effects.
5.13.1 If you intend to accomplish a product change by incorporating several design changes in a sequential manner, you should identify to the FAA up front when the first application is made. In addition, the cumulative effects arising from the initial change, and from all of the follow-on changes should be included as part of the description of the change in the initial proposal. The classification of the intended product change will not be evaluated solely on the basis of the first application, but rather on the basis of all the required design changes needed to accomplish the intended product change. If the FAA determines that the current application is a part of a sequence of related changes, then the FAA will re-evaluate the determination of significance and the resulting certification basis as a group of related changes.
5.13.2 Example: Cumulative Effects—Advancing the Certification Basis. The type certificate for airplane model X lists three models, namely X-300, X-200, and X-100. The X-300 is derived from the X-200, which is derived from the original X-100 model. An applicant proposes a design change to the X-300 airplane model. During the review of the X-300 certification basis and the regulations affected by the proposed change, it was identified that one regulation, § 25.571 (damage tolerance requirements), remained at the same amendment level as the X-100 original certification basis (exception granted on the X-200). Since the amendment level for this particular regulation was not changed for the two subsequent airplane models (X-200 and X-300), the applicant must now examine the cumulative effects of these two previous design
03/11/16 AC 21.101-1B
changes that are related to the proposed change and the damage tolerance requirements to determine whether the amendment level needs to advance.
AC 21.101-1B › APPENDIX A. CLASSIFICATION OF DESIGN CHANGES
A-1
APPENDIX A. CLASSIFICATION OF DESIGN CHANGES
The following tables of “substantial,” “significant,” and “not significant” changes are adopted by the FAA, Agência Nacional de Aviação Civil (ANAC), European Aviation Safety Agency (EASA), and Transport Canada Civil Aviation (TCCA) through international collaboration. The classification may change due to cumulative effects and/or combinations of individual changes.
A.1 Examples of Substantial, Significant, and Not Significant Changes for Small Airplanes (Part 23).
A.1.1 Table A-1 contains examples of changes that are “substantial” for small airplanes (part 23).
Table A-1. Examples of Substantial Changes for Small Airplanes (Part 23)
Example Description of Change Notes
1. Change in wing location (tandem, forward, canard, high/low).
Proposed change in design is so extensive that a substantially complete investigation of compliance with the applicable regulations is required.
2. Fixed wing to tilt wing. Proposed change in design is so extensive that a substantially complete investigation of compliance with the applicable regulations is required.
3. A change in the number of engines. Proposed change in design is so extensive that a substantially complete investigation of compliance with the applicable regulations is required.
4. Replacement of piston or turbo-prop engines with turbojet or turbofan engines.
Proposed change in design is so extensive that a substantially complete investigation of compliance with the applicable regulations is required.
A-2
Table A-1. Examples of Substantial Changes for Small Airplanes (Part 23) (continued)
Example Description of Change Notes
5. Change in engine configuration (tractor/pusher). Proposed change in design is so extensive that a substantially complete investigation of compliance applicable regulations is required.
with the
6. Increase from subsonic to supersonic flight regime.
7. Change from an all-metal to all-composite airplane. Proposed change in design is so extensive that a substantially complete investigation of compliance applicable regulations is required.
with the
8. Certificating a part 23 (or predecessor amendment airplane basis airplane such as CAR 3) into another regulatory category such as part 25.
APPENDIX A. CLASSIFICATION OF DESIGN CHANGES › Table A-2. Examples of Significant Changes for Small Airplanes (Part 23)
A-3
A.1.2 Table A-2 contains examples of changes that are “significant” for small airplanes (part 23).
Table A-2. Examples of Significant Changes for Small Airplanes (Part 23)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
1. Conventional tail to T-tail or V-tail, or vice versa.
Yes No Yes Change in general configuration. Requires extensive, structural flying qualities and performance reinvestigation. Requires new airplane flight manual (AFM) to address performance and flight characteristics.
2. Changes in wing configuration such as change in dihedral, changes in wing span, flap or aileron span, addition of winglets, or increase of more than 10 percent of the original wing sweep at the quarter chord.
Yes No Yes Change in general configuration. Likely requires extensive changes to wing structure. Requires new AFM to address performance and flight characteristics.
Note: Small changes to the wingtip or winglet are not significant changes. See table for “not significant” changes.
A-4
Table A-2. Examples of Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
3. Changes to tail configuration such as the addition of tail strakes or angle of incidence of the tail.
Yes No Yes Change in general configuration. Likely requires extensive changes to tail structure. Requires new AFM to address performance and flight characteristics.
Note: Small changes to tail are not significant changes.
4. Tricycle/tail wheel undercarriage change or addition of floats.
Yes No No Change in general configuration. Likely, at airplane level, general configuration and certification assumptions remain valid.
5. Passenger to freighter configuration conversion that involves the introduction of a cargo door or an increase in floor loading of more than 20 percent, or provision for carriage of passengers and freight together.
Yes No Yes Change in general configuration affecting load paths, aeroelastic characteristics, aircraft related systems, etc. Change in design assumptions.
A-5
Table A-2. Examples of Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
6. Replace reciprocating engines with the same number of turbo-propeller engines.
Yes No No Requires extensive changes to airframe structure, addition of aircraft systems, and new AFM to address performance and flight characteristics.
7. Addition of a turbo-charger that changes the power envelope, operating range, or limitations.
No No Yes Invalidates certification assumptions due to changes in operating envelope and limitations. Requires new AFM to address performance and flight characteristics.
A-6
Table A-2. Examples of Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
8. The replacement of an engine of higher rated power or increase thrust would be considered significant if it would invalidate the existing substantiation, or would change the primary structure, aerodynamics, or operating envelope sufficiently to invalidate the assumptions of certification.
No Yes Yes Invalidates certification assumptions. Requires new AFM to address performance and flight characteristics. Likely changes to primary structure. Requires extensive construction reinvestigation.
9. A change in the type of material, such as composites in place of metal, or one composite fiber material system with another (e.g., carbon for fiberglass), for primary structure would normally be assessed as a significant change.
No Yes Yes Change in principles of construction and design from conventional practices. Likely change in design/certification assumptions.
A-7
Table A-2. Examples of Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
10. A change involving appreciable increase in design speeds VD, VB, VMO, VC, or VA.
No No Yes Certification assumptions invalidated. Requires new AFM to address performance and flight characteristics.
11. Installation of a short takeoff and landing (STOL) kit.
No No Yes Certification assumptions invalidated. Requires new AFM to address performance and flight characteristics.
12. A change in the rated power or thrust could be a significant change if the applicant is taking credit for increased design speeds per example 10 of this table.
No No Yes Certification assumptions invalidated. Requires new AFM to address performance and flight characteristics.
A-8
Table A-2. Examples of Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
13. Fuel state such as compressed gaseous fuels or fuel cells. This could completely alter the fuel storage and handling systems and possibly affect the airplane structure.
No No Yes Changes in design/certification assumptions. Extensive alteration of fuel storage and handling systems.
14. A change in the flight control concept for an aircraft, e.g., to fly by wire (FBW) and side-stick control, or a change from hydraulic to electronically actuated flight controls, would in isolation normally be regarded as a significant change.
No No Yes Changes in design and certification assumptions. Requires extensive systems architecture and integration reinvestigation. Requires new AFM.
A-9
Table A-2. Examples of Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
15. Change to airplane’s operating altitude, or cabin operating pressure greater than 10 percent in maximum cabin pressure differential.
No No Yes This typically invalidates certification assumptions and the fundamental approach used in decompression, structural strength, and fatigue. May require extensive airframe changes affecting load paths, fatigue evaluation, aeroelastic characteristics, etc. Invalidates design assumptions.
16. Addition of cabin pressurization system.
No Yes Yes Extensive airframe changes affecting load paths, fatigue evaluation, aeroelastic characteristics, etc. Invalidates design assumptions.
17. Changes in types and number of emergency exits or an increase in maximum certificated passenger capacity.
Yes No Yes Emergency egress requirements exceed those previously substantiated. Invalidates assumptions of certification.
A-10
Table A-2. Examples of Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
18. A change in the required number of flightcrew that necessitates a complete flightdeck rearrangement, and/or an increase in pilot workload.
No No Yes Extensive changes to avionics and aircraft systems. Invalidates certification assumptions. Requires new AFM.
19. Expansion of an aircraft’s operating envelope.*
No No Yes*
*Some changes may be deemed “not significant” depending on the extent of the expansion.
An expansion of operating capability is a significant change (e.g., an increase in maximum altitude limitation, approval for flight in icing conditions, or an increase in airspeed limitations).
20. Replacement of an aviation gasoline engine with an engine of approximately the same horsepower utilizing, e.g., diesel, hybrid, or electrical power.
No No Yes A major change to the airplane. The general configuration and principles of construction will usually remain valid; however, the assumptions for certification are invalidated.
A-11
Table A-2. Examples of Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
21. Comprehensive flightdeck upgrade, such as conversion from entirely federated, independent electro-mechanical flight instruments to highly integrated and combined electronic display systems with extensive use of software and/or complex electronic hardware.
No No Yes Affects avionics and electrical systems integration and architecture concepts and philosophies.
This drives a reassessment of the human-machine interface, flightcrew workload, and re-evaluation of the original design flightdeck assumptions.
22. Introduction of autoland. No No Yes Invalidates original design assumptions.
23. Conversion from a safe life design to a damagetolerance-based design.
No No Yes Where the airframeestablished safe life limits change to damage tolerance principles, then use of an inspection program in lieu of the safe life design limit invalidates the original assumptions used during certification.
A-12
Table A-2. Examples of Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
24. Extensive structural airframe modification, such as a large opening in the fuselage.
Yes No No Requires extensive changes to fuselage structure, affects aircraft systems, and requires a new AFM to address performance and flight characteristics.
25. Fuselage stretch or shortening in the cabin or pressure vessel.
Yes No Yes Cabin interior changes are related changes since occupant safety considerations are impacted by a cabin length change. Even if a new cabin interior is not included in the product level change, the functional effect of the fuselage plug has implications on occupant safety (e.g., the dynamic environment in an emergency landing, emergency evacuation, etc.), and thus the cabin interior becomes an affected area.
A-13
Table A-2. Examples of Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
26. Conversion from normal category to commuter category airplane.
Yes No Yes Requires compliance with all commuter regulatory standards. In many cases, this change could be considered a substantial change to the type design. Therefore, a proposed change of this nature would be subject to FAA determination under § 21.19.
27. Installation of a full authority digital engine control (FADEC) on an airplane that did not previously have a FADEC installed.
No No Yes
A-14
A.1.3 Table A-3 contains examples of changes that are “not significant” for small airplanes (part 23).
Table A-3. Examples of Not Significant Changes for Small Airplanes (Part 23)
APPENDIX A. CLASSIFICATION OF DESIGN CHANGES › Table A-3.
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
1. Addition of wingtip modifications (not winglets).
No No No A major change to the airplane. Likely, the original general configuration, principles of construction, and certification assumptions remain valid.
2. Installation of skis or wheel skis.
No No No Although a major change to the airplane, likely the original general configuration, principles of construction, and certification assumptions remain valid.
3. Forward looking infrared (FLIR) or surveillance camera installation.
No No No Additional flight or structural evaluation may be necessary, but the change does not alter basic airplane certification.
4. Litter, berth, and cargo tie down device installation.
No No No Not an airplane-level change.
A-15
Table A-3. Examples of Not Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
5. Increased tire size, including tundra tires.
No No No Not an airplane-level change.
6. Replacement of one propeller type with another (irrespective of increase in number of blades).
No No No Although a major change to the airplane, likely the original general configuration, principles of construction, and certification assumptions remain valid.
7. Addition of a turbo-charger that does not change the power envelope, operating range, or limitations (e.g., a turbo-normalized engine, where the additional power is used to enhance high altitude or hot day performance).
No No No Not an airplane-level change.
8. Substitution of one method of bonding for another (e.g., change in type of adhesive).
No No No Not an airplane-level change.
A-16
Table A-3. Examples of Not Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
9. Substitution of one type of metal for another.
No No No Not an airplane-level change.
10. Any change in construction or fastening not involving primary structure.
No No No Not an airplane-level change.
11. A new fabric type for fabric-skinned aircraft.
No No No Not an airplane-level change.
12. Increase in flap speed or undercarriage limit speed.
No No No Although a major change to the airplane, likely the original general configuration, principles of construction, and certification assumptions remain valid.
13. Structural strength increases.
No No No Although a major change to the airplane, likely the original general configuration, principles of construction, and certification assumptions remain valid.
A-17
Table A-3. Examples of Not Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
14. Instrument flight rules (IFR) upgrades involving installation of components (where the original certification does not indicate that the airplane is not suitable as an IFR platform, e.g., special handling concerns).
No No No Not an airplane-level change.
15. Fuel tanks where fuel is changed from gasoline to diesel fuel and tank support loads are small enough that an extrapolation from the previous analysis would be valid. Chemical compatibility would have to be substantiated.
No No No Not an airplane-level change.
A-18
Table A-3. Examples of Not Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
16. Limited changes in a pressurization system, e.g., number of outflow valves, type of controller, or size of pressurized compartment, but the system must be resubstantiated if the original test data are invalidated.
No No No Although a major change to the airplane, likely the original general configuration, principles of construction, and certification assumptions remain valid.
17. Install a different exhaust system.
No No No Not an airplane-level change.
18. Changes in engine cooling or cowling.
No No No Not an airplane-level change.
19. Changing fuels of substantially the same type, such as AvGas to AutoGas, AvGas (80/87) to AvGas (100LL), ethanol to isopropyl alcohol, Jet B to Jet A.
No No No Although a major change to the airplane, likely the original general configuration, principles of construction, and certification assumptions remain valid.
A-19
Table A-3. Examples of Not Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
20. Fuels that specify different levels of “conventional” fuel additives that do not change the primary fuel type. Different additive levels (controlled) of MTBE, ETBE, ethanol, amines, etc., in AvGas would not be considered a significant change.
No No No Although a major change to the airplane, likely the original general configuration, principles of construction, and certification assumptions remain valid.
21. A change to the maximum takeoff weight of less than 5 percent, unless assumptions made in justification of the design are thereby invalidated.
No No No Although a major change to the airplane, likely the original general configuration, principles of construction, and certification assumptions remain valid.
22. An additional aileron tab (e.g., on the other wing).
No No No Although a major change to the airplane, likely the original general configuration, principles of construction, and certification assumptions remain valid.
A-20
Table A-3. Examples of Not Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
23. Larger diameter flight control cables with no change in routing, or other system design.
No No No Not an airplane-level change.
24. Autopilot installation (for IFR use, unless the original certification indicates that the airplane is not suitable as an IFR platform).
No No No Although a major change to the airplane, likely the original general configuration, principles of construction, and certification assumptions remain valid.
25. Increased battery capacity or relocate battery.
No No No Not an airplane-level change.
26. Replace generator with alternator.
No No No Not an airplane-level change.
27. Additional lighting (e.g., navigation lights, strobes).
No No No Not an airplane-level change.
28. Higher capacity brake assemblies.
No No No Not an airplane-level change.
A-21
Table A-3. Examples of Not Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
29. Increase in fuel tank capacity.
No No No Not an airplane-level change.
30. Addition of an oxygen system.
No No No Not an airplane-level change.
31. Relocation of a galley. No No No Not an airplane-level change.
32. Passenger to freight (only) conversion with no change to basic fuselage structure.
No No No Although a major change to the airplane, likely the original general configuration, principles of construction, and certification assumptions remain valid.
Requires certification substantiation applicable to freighter requirements.
33. New cabin interior with no fuselage length change.
No No No
34. Installation of new seat belt or shoulder harness.
No No No Not an airplane-level change.
A-22
Table A-3. Examples of Not Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
35. A small increase in center of gravity (CG) range.
No No No At airplane level, no change in general configuration, principles of construction, and certification assumptions.
36. Auxiliary power unit (APU) installation that is not flight essential.
No No No Although a major change to the airplane level, likely the original general configuration, principles of construction, and certification assumptions remain valid.
Requires certification substantiation applicable to APU installation requirements.
37. An alternative autopilot. No No No Not an airplane-level change.
38. Addition of Class B terrain awareness and warning systems (TAWS).
No No No Not an airplane-level change.
A-23
Table A-3. Examples of Not Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
39. Extending an established life limit.
No No No This extension may be accomplished by various methods, such as ongoing fatigue testing, service life evaluation, component level replacement, and inspections based on damage tolerance principles.
40. Flightdeck replacement of highly integrated and combined electronic display systems with other highly integrated and combined electronic display systems.
No No No Not significant if the architecture concepts, design philosophies, human-machine interface, or flight crew workload assumptions are not impacted.
41. Interior cabin reconfigurations are generally considered not significant. This includes installation of in-flight entertainment (IFE), new seats, and rearrangement of furniture.
No No No
A-24
Table A-3. Examples of Not Significant Changes for Small Airplanes (Part 23) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
42. Modification to ice protection systems.
No No No Re-certification required, but certification basis should be evaluated for adequacy.
APPENDIX A. CLASSIFICATION OF DESIGN CHANGES › Table A-4.
A-25
A.2 Examples of Substantial, Significant, and Not Significant Changes for Transport Airplanes (Part 25).
A.2.1 Table A-4 contains examples of changes that are “substantial” for transport airplanes (part 25).
Table A-4. Examples of Substantial Changes for Transport Airplanes (Part 25)
Example Description of change Notes
1. Change in the number or location of engines, e.g., four to two wing-mounted engines or two wing-mounted to two body-mounted engines.
Proposed change in design is so extensive that a substantially complete investigation of compliance with the applicable regulations is required.
2. Change from a high-wing to low-wing configuration. Proposed change in design is so extensive that a substantially complete investigation of compliance with the applicable regulations is required.
3. Change from an all-metal to all-composite airplane. Proposed change in design is so extensive that a substantially complete investigation of compliance with the applicable regulations is required.
4. Change of empennage configuration for larger airplanes (cruciform vs. ‘T’ or ‘V’ tail).
Proposed change in design is so extensive that a substantially complete investigation of compliance with the applicable regulations is required.
5. Increase from subsonic to supersonic flight regime. Proposed change in design is so extensive that a substantially complete investigation of compliance with the applicable regulations is required.
APPENDIX A. CLASSIFICATION OF DESIGN CHANGES › Table A-5.
A-26
A.2.2 Table A-5 contains examples of changes that are “significant” for transport airplanes (part 25).
Table A-5. Examples of Significant Changes for Transport Airplanes (Part 25)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
1. Reduction in the number of flightcrew (in conjunction with flightdeck update).
No No Yes Extensive changes to avionics and aircraft systems. Impact to crew workload and human factors, pilot type rating.
2. Modify an airplane to add certification for flight in icing conditions by adding systems such as ice detection and ice protection.
Yes No Yes New aircraft operating envelope. Requires major new systems installation and aircraft evaluation. Operating envelope changed.
3. Conversion—passenger or combination freighter/passenger to all freighter, including cargo door, redesign floor structure and 9g net or rigid barrier.
Yes No Yes Extensive airframe changes affecting load paths, aeroelastic characteristics, aircraft related systems for fire protection, etc. Design assumptions changed from passenger to freighter.
A-27
Table A-5. Examples of Significant Changes for Transport Airplanes (Part 25) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
4. Conversion from a cargo to passenger configuration.
Yes No Yes Completely new floor loading and design. Redistribution of internal loads, change in cabin safety requirements, system changes.
5. Increase in cabin pressurization greater 10 percent. than
No No Yes A change greater than 10 percent in operational cabin pressure differential is a significant change since it requires extensive airframe changes affecting load paths, fatigue evaluation, or aeroelastic characteristics, invalidating the certification assumptions.
6. Addition of leading slats.
edge Yes No Yes The addition of leading edge slats is significant since it requires extensive changes to wing structure, adds aircraft systems, and requires a new AFM to address performance and flight characteristics.
A-28
Table A-5. Examples of Significant Changes for Transport Airplanes (Part 25) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
7. Fuselage stretch or shortening in the cabin or pressure vessel.
Yes No Yes Cabin interior changes are related changes since occupant safety considerations are impacted by a cabin length change. Even if a new cabin interior is not included in the product level change, the functional effect of the fuselage plug has implications on occupant safety (e.g., the dynamic environment in an emergency landing, emergency evacuation, etc.), and thus the cabin interior becomes an affected area.
8. Extensive structural airframe modification, such as installation of a large telescope with large opening in the fuselage.
Yes No No These types of structural modifications are significant since they require extensive changes to fuselage structure, affect aircraft systems, and require a new AFM to address performance and flight characteristics.
A-29
Table A-5. Examples of Significant Changes for Transport Airplanes (Part 25) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
9. Changing the number of axles or number of landing gear done in context with a product change that involves changing the airplane gross weight.
Yes No No This type of landing gear change with an increase in gross weight is significant since it requires changes to aircraft structure, affects aircraft systems, and requires AFM changes, which invalidate the certification assumptions.
10. Primary structure changes from metallic material to composite material.
No Yes No Change in principles of construction and design from conventional practices.
11. An increase in design weight of more than 10 percent.
No No Yes Design weight increases of more than 10 percent result in significant design load increase that invalidates the assumptions used for certification, requiring re-substantiation of aircraft structure, aircraft performance, and flying qualities and associated systems.
A-30
Table A-5. Examples of Significant Changes for Transport Airplanes (Part 25) (continued)
Example Description of change
Is there a change to the general configuration? § 21.101(b)(1)(i)
Is there a change to the principles of construction? § 21.101(b)(1)(i)
Have the assumptions used for certification been invalidated? § 21.101(b)(1)(ii) Notes
12. Installation of winglets, modification of existing winglets, or other changes in wing tip design.
Continue reading ↓ 120 of 251 passages shown