Radar Vectors
Advisory Circular Cancelled Issued Apr 21, 1971 AIR-120 92 pages Copy saved Nov 17, 2026

AC 20-73 Aircraft Ice Protection

Provides information relating to the substantiation of ice protection systems on aircraft.

This document is cancelled. Cancelled by 20-73A. Check the official source before relying on it.

Official source ↗ Open PDF

Advisory U.S. Department of Transportation Federal Aviation Circular Administration

Subject: AIRCRAFT ICE PROTECTION Date: 21 April 71 AC No. 20-73

Initiated by : FS-140 Change:

FOREWORD

1. PURPOSE. This advisory circular contains information

relating to the substantiation of ice protection systems on

aircraft.

2. REFERENCE. Federal Aviation Regulations, Sections

23.1093(b), 23.1583(h), 25.1093(b), 25.1419, 25.1583(e), 27.1093(b), 27.1583(e), 29.1093(b), and 29.1583(e).

3. SCOPE. The procedures described in this advisory circular

are presented for guidance purposes only and are not

mandatory or regulatory in nature. Other methods may be equally effective and acceptable.

/s/ R. S. Sliff

Acting Director Flight Standards Service

TABLE OF CONTENTS

TABLE OF CONTENTS

Page No.

CHAPTER 1. TYPES OF SYSTEMS 1

1 1. General

2. Hot Air Systems 1 3. Electrical Resistance Systems 1 4. Liquid Systems 1 5. Expandable Boot Systems 2

CHAPTER 2. DESIGN FACTORS 3

SECTION 1. GENERAL 3

6. General 3

SECTION 2. METEOROLOGICAL DATA 3

7. General 3 8. LWC 3 9. Droplet Diameter 4 10. Temperature 5 11. Use of Meteorological Data for Design 5

SECTION 3. OPERATIONAL FACTORS 6

SECTION 3. OPERATIONAL FACTORS 6

12. Airplane Operational Factors 6 13. Helicopter Operational Factors 7 14. Engine Operational Factors 7 15. Holding Phase 8

SECTION 4. OTHER FACTORS 8

16. Ice Shedding 8 17. Ice Shapes 9 18. Unprotected Surface 10

CHAPTER 3. DESIGN ANALYSIS 11

19. General 11

20. Airframe Surface, Wings, Empennage, Control

20. Airframe Surface, Wings, Empennage, Control

Surface, etc. 12 21. Engine Inlets, Windshields, and Instruments 14 22. Engine and Propeller Systems 15 23. Summary of Design Procedures 17

CHAPTER 4. TESTS 19

SECTION 1. GENERAL 19

24. General 19

SECTION 2. TEST METHODS 19

25. Natural Icing Flight Tests 19 26. Dry Air Flight Tests 21 27. Flying Tanker Tests 21 28. Self-Contained Spray Rig Tests 22 29. Icing Tunnel Tests 22 30. Combination of Methods 23 31. Ice Shedding 23

SECTION 3. TEST PROCEDURES 24

SECTION 3. TEST PROCEDURES 24

32. Airframe Surfaces, Wings, Empennage, Control

Surfaces, Engine Inlets, Windshields, and

Instruments, etc., Systems 24 33. Engines 25 34. Helicopter Engine Inlet and Rotor 27

SECTION 4. FINDING ICING CONDITIONS FOR TEST PURPOSES 28

35. General 28 36. Finding Ice in Stratoform Clouds 29 37. Finding Ice in Cumuliform Clouds 30

CHAPTER 5. SUMMARY OF RECOMMENDED PROCEDURES FOR TYPE

CHAPTER 5. SUMMARY OF RECOMMENDED PROCEDURES FOR TYPE

CERTIFICATION 33

38. Airframe Manufacturer 33 39. Engine Manufacturer 33

APPENDIX 1. BIBLIOGRAPHY (2 pages) 1

APPENDIX 2. SELECTED BIBLIOGRAPHY OF UNCLASSIFIED

NASA-NACA AIRCRAFT ICING REPORTS (11 pages) 1

CHAPTER 1. TYPES OF SYSTEMS

CHAPTER 1. TYPES OF SYSTEMS

1. GENERAL. There are four types of systems used for

anti-icing or de-icing exposed surfaces. These are:

a. Hot air systems.

b. Electrical resistance systems.

c. Liquid systems.

d. Expandable boot systems.

A brief discussion of each type follows:

2. HOT AIR SYSTEMS. Hot air systems are used on most of the

large jet transports because of the availability of hot air from the engines, and the relative efficiency and reliability of these systems. Hot air is used to anti-ice or de-ice leading edge wing panels and high lift devices,

empennage surfaces, engine inlet and air scoops, radomes, and some types of instruments. Systems whose sources of hot

air are separate heat exchangers have also been used where

CHAPTER 5. SUMMARY OF RECOMMENDED PROCEDURES FOR TYPE

CHAPTER 5. SUMMARY OF RECOMMENDED PROCEDURES FOR TYPE

CERTIFICATION 33

38. Airframe Manufacturer 33 39. Engine Manufacturer 33

APPENDIX 1. BIBLIOGRAPHY (2 pages) 1

APPENDIX 2. SELECTED BIBLIOGRAPHY OF UNCLASSIFIED

NASA-NACA AIRCRAFT ICING REPORTS (11 pages) 1

CHAPTER 1. TYPES OF SYSTEMS

CHAPTER 1. TYPES OF SYSTEMS

1. GENERAL. There are four types of systems used for

anti-icing or de-icing exposed surfaces. These are:

a. Hot air systems.

b. Electrical resistance systems.

c. Liquid systems.

d. Expandable boot systems.

A brief discussion of each type follows:

2. HOT AIR SYSTEMS. Hot air systems are used on most of the

large jet transports because of the availability of hot air from the engines, and the relative efficiency and reliability of these systems. Hot air is used to anti-ice or de-ice leading edge wing panels and high lift devices,

empennage surfaces, engine inlet and air scoops, radomes, and some types of instruments. Systems whose sources of hot

air are separate heat exchangers have also been used where

engines cannot supply the required air mass flows or temperatures.

3. ELECTRICAL RESISTANCE SYSTEMS. Electrical systems have been

used on several larger transport aircraft. These systems are generally de-icing rather than anti-icing because of the large power requirements for continuous operation. Various

cycles are devised and tested to provide the most effective system at the least expenditure of power. Because these systems usually require large amounts of power and are less reliable than hot air systems, they have not been widely used on large transport aircraft except for small areas such as windshields, propeller boots, pitot tubes, static ports, radio masts, air scoop inlets, radomes, etc., and in some

instances on the horizontal stabilizers.

4. LIQUID SYSTEMS. Liquid systems using glycol, alcohol, or

mixtures of these and other chemicals have been devised for such applications as wing panels, windshields, engine inlets, and propellers. Several methods have been devised

for applying the liquid to the protected surfaces. For

large surfaces, porous materials through which the liquid is pressure fed, have been used. Sprays and slinger rings have also been used in such areas as windshields and propellers. Liquids may be used either to de-ice or anti-ice protected

surfaces. The quantity of liquid which can be carried may impose a limitation. Because the flow of liquid must be regulated by small orifices and these orifices are subject

to clogging, these systems have not found general usage on large jet transport aircraft.

5. EXPANDABLE BOOT SYSTEMS. Expandable boot systems consisting

of sectionalized panels have been used extensively on reciprocating-engine-powered aircraft and on many small

turbine-powered aircraft. These panels have been used with good results on wing and empennage leading edges, radomes,

and other areas. These systems are generally not suitable

for use on engine inlets or propellers where ice ingestion or propeller unbalance would be a hazard.

CHAPTER 2. DESIGN FACTORS

CHAPTER 2. DESIGN FACTORS

SECTION 1. GENERAL

6. GENERAL. Ice protection systems are designed to provide

protection when the aircraft is exposed to the conditions leading to icing likely to be encountered in service. Determination of the design conditions involves

consideration of the following:

SECTION 1. GENERAL

a. The meteorological conditions of FAR 25, Appendix C.

b. The operational conditions which would affect the

accumulation of ice on protected and unprotected

surfaces of the aircraft.

c. The operational conditions of the engine and propeller

(if applicable) which would affect the accumulation of ice and/or the availability of energy to operate the

system.

SECTION 2. METEOROLOGICAL DATA

SECTION 2. METEOROLOGICAL DATA

7. GENERAL. The meteorological data in FAR 25 Appendix C are

divided into continuous maximum conditions and intermittent maximum conditions. The two divisions are the results of analyses performed by NACA of data collected from many sources over a period of time. Continuous maximum conditions are defined by Figures 1, 2, and 3 of Appendix C

of FAR 25. Intermittent maximum conditions are defined by Figures 4, 5, and 6 of Appendix C of FAR 25. The data in

Appendix C are not intended to imply that icing conditions of both types are limited to the altitudes described in

Appendix C. The data used to develop the curves were the results of a statistical analysis performed by NACA which

recognizes the random nature of meteorological data. Meteorological data are defined in terms of liquid water content (LWC), droplet diameter (Dd), and temperature (T),

and each of these parameters is involved in the

determination of the design points.

8. LIQUID WATER CONTENT. LWC gm/(m cubed) is of prime interest

to the designer because it influences the maximum quantity of ice that can accumulate. All of the liquid to which a surface is exposed, however, does not collect on the surface. Water collection is a function of flight speed, airfoil geometry, droplet size, and other ambient conditions, in addition to LWC. Data covering conditions within a specific cloud type indicate that there is a definite relationship between LWC, temperature, pressure altitude, and droplet diameter. Statistical analysis of data covering many icing encounters, in contrast with that shown for conditions in a single cloud type, indicates that high LWCs are associated with high temperatures and low

droplet diameters and vice versa. This trend is shown in the FAR curves. Figures 3 and 6 of the FAR curves showing the variation of LWC factor with distance are primarily of interest in predicting the amount of ice which can

accumulate on unprotected surfaces during a selected period of exposure. However, for the design of ice protection

systems, the unadjusted values of 17.4 nautical miles for

stratiform clouds and 2.6 nautical miles for cumuliform clouds are used to obtain the design LWC value.

9. DROPLET DIAMETER. All the water contained in the swept

volume of a cloud formation does not impinge on the exposed surfaces. Impingement rate is a function of droplet size as well as quantity. The large drops due to their increased

inertia have the higher impingement rate. Drops occur in many sizes in nature. The distributions most commonly used

are shown in the following table.

TABLE I

TABLE I

Total LW in Each a/(a sub 0) Size Group -- % Distributions --------------------------------------------------------­

A B C D E --------------------------------------------------------­

5% 1.00 0.56 0.42 0.31 0.23

10% 1.00 0.72 0.61 0.52 0.44

20% 1.00 0.84 0.77 0.71 0.65

30% 1.00 1.00 1.00 1.00 1.00

20% 1.00 1.17 1.26 1.37 1.48

10% 1.00 1.32 1.51 1.74 2.00

5% 1.00 1.49 1.81 2.22 2.71

--------------------------------------------------------­

The size of droplets contained in a distribution is expressed as the ratio of the average diameter "a" in each

group to the volume median drop diameter "a sub 0." Due to the difficulty in measuring the distribution of droplet sizes in an icing cloud, however, it has become common practice to refer to a mean effective drop diameter -- MED. The MED divides a distribution so that the volume of water contained in drops of a larger diameter than the MED is equal to the volume of water contained in drops of a smaller diameter. An MED of 20 microns has been successfully used to determine the water catch rate and an MED of 50 microns

has been successfully used to determine the impingement

limits. However, the complete range of droplet sizes should be considered to establish the most severe conditions.

10. TEMPERATURE. Temperature affects the severity of an icing

encounter in many ways. Data indicate that the highest LWC concentrations occur at the higher temperatures as

previously indicated. This trend can be seen in the FAR curves. Temperature affects the impingement computations which involve viscosity, density, and the quantity of heat, Q, required to anti-ice or de-ice a surface. In this respect, a system design is usually chosen such that the Q sub A available exceeds the Q sub R required for a chosen

group of meteorological and operational conditions.

11. USE OF METEOROLOGICAL DATA FOR DESIGN.

a. LWC, droplet diameter, and temperature are used to

determine the water catch rate, M sub T, and extent of ice accumulation on a surface. The collection rate is given by the following equation:

M sub T = 0.3296 (E sub M) V(LWC) tC

where:

M sub T = Mass of water intercepted 1b/hr/ft of

airfoil span

0.3296 = Conversion factor (will vary with the units used)

E sub M = Collection efficiency of airfoil %

LWC = Liquid Water Content gm/(m cubed)

t = Airfoil thickness % of chord length

C = Chord length ft.

V = Airplane speed MPH

The airfoil thickness may sometimes be expressed as h/c

where h is the projected height of the airfoil normal to the flight path. The collection efficiency defined as the ratio of the mass of liquid water collected by a surface to the mass of liquid water contained in the swept volume of the surface at a given angle of attack,

is a function of flight speed, droplet size, body geometry, ambient temperature and pressure.

b. The collection efficiency of a surface can be determined

either by analysis or test. This requires a knowledge

of the flow field around the surface. Flow field data determine the streamlines around a surface, and hence, the drag forces acting on a droplet. The pressure distribution may be determined analytically or

experimentally by wind tunnel or flight tests. Once the pressure distribution is known, the flow field can be calculated.

c. In some cases, the impingement characteristics can be

estimated by a "matching technique" by which a particular airfoil section is compared to a model of

known impingement characteristics. Plots and tables

relating the various functional parameters used to determine collection efficiency are available.

"Matching techniques" should be used with caution on sections where the airfoil section is subjected to

influences which did not exist when impingement characteristics were established on the reference model. Such influences would include but are not limited to engine air flow into an inlet duct, propeller wash on various surfaces, wing downwash effects on aft mounted

engine inlets, etc.

d. The ultimate point at which a droplet impinges on a

surface is the resultant of inertia as well as drag forces. A 20-micron droplet diameter is usually used to determine water catch rates; however, the entire range of values should be considered. A droplet diameter of 40 microns is often used to determine impingement

limits. In some cases, the water catch due to the increased droplet size may be ignored; however, the manufacturers should show that consideration was given

to such limits.

SECTION 3. OPERATIONAL FACTORS

12. AIRPLANE OPERATIONAL FACTORS.

a. The determination of the most severe conditions for

SECTION 3. OPERATIONAL FACTORS

which an icing system is to be designed involves

consideration of the operational characteristics of the airplane. Operational regimes such as climb, cruise,

hold, and descent are usually investigated at various altitudes. For airplanes with low-speed, high-lift devices, the operational regime during which these

devices are used may be the most severe. In other cases, the cruise condition may be the most severe because of the lift, drag, or control problems associated with the buildup of ice on exposed surfaces.

Service experience indicates that holding in icing conditions for as much as 45 minutes is an operational

condition that may be encountered.

b. The airplane attitude can contribute to the formation of

ice on critical areas. The type and shape of ice

formation, and the surface on which the ice forms are, among other things, functions of airspeed and angle of

attack.

c. For a given set of meteorological conditions, the rate

and extent of ice accumulation is a function of flight speed as well as airfoil or body geometry.

d. Small bodies moving at high speeds encountering large

droplets will exhibit a high collection efficiency. The flow field associated with larger bodies results in a smaller collection efficiency.

e. The duration of the exposure of an airplane to severe

icing conditions is dependent on the flight speed of the

aircraft and the extent of the icing cloud. However,

icing tunnel tests show that the accumulations of ice on a surface are not always in a linear relationship with

time, especially for accumulations of glaze ice. Ice growth changes the airfoil characteristics and causes a continual change in collection rate above the initial rate; therefore, extrapolating ice accumulations as a linear function of time can be very misleading.

13. HELICOPTER OPERATIONAL FACTORS. Current development of

helicopter rotor system de-icing or anti-icing means has not provided systems or hardware deemed acceptable by helicopter

manufacturers. Therefore, all helicopters to date have been restricted against operating in icing conditions. This restriction does not insure that icing conditions will not

be encountered inadvertently. Therefore, it is necessary that the powerplant be protected against the effects of ice

accumulation as specified in the regulations; however, continuing exposure to icing conditions may cause the helicopter to become incapable of sustaining flight. In view of this, there appears to be little constructive purpose in requiring an indefinite protection of the helicopter powerplant installation against ice conditions as

long as the protection that is provided assures a level of safety equivalent to that required by the regulations throughout conditions and duration of exposure under which

flight can be maintained.

14. ENGINE OPERATIONAL FACTORS.

a. The engine operational factors to be considered in

determining the most severe conditions are directly

related to aircraft operational procedures because changes in airplane speed and attitude are usually accompanied by changes in engine power requirements. The prime factors to be evaluated are the quantity and temperature of air available from the engine and the

airflow through the engine during the most critical operational mode. These factors are especially critical for evaluation of hot air systems where the air source is the engine. The airflow through the engine is critical in terms of the flow field around the inlet lip and the engine inlet. The flow field must be known in

order to determine the heat transfer relationships

between the heated surfaces, the hot air used to heat the surfaces, and the quantity of water impinging on the

surfaces. During some operational modes, the inlet static pressure and temperature are below ambient. In marginal icing conditions, this reduction in temperature may be sufficient to cause ice to form in the inlet.

b. Engine inlets, inlet air screens, and inlet lips are

considered to be more critical with respect to accumulations of ice on surfaces exposed to engine airflow due to the possibility of an appreciable quantity of ice being ingested into the engine. Ice ingestion can cause serious damage to compressor or fan

blades. Runback water can also refreeze on unprotected surfaces of the inlet and, if excessive, can reduce engine airflow or distort the flow pattern in such a manner as to excite compressor or fan blades to critical

frequencies.

c. Various engine operational modes have an effect on the

collection of ice on propeller surfaces of

propeller-driven aircraft. Propeller surfaces are treated similarly to other surfaces in determining the extent and degree of ice protection required. The greatest quantity of ice normally collects on the spinner and inner radius of the propeller. Aerodynamic

heating and centrifugal force tend to eliminate ice from the other surfaces. Propeller areas on which ice may accumulate and be ingested into the engine should be

anti-iced, rather than de-iced, to reduce the probability of ice being shed into the engine.

d. In addition to the foregoing, the buildup of ice on

unprotected surfaces and the general operational conditions prevalent during an icing encounter place further emphasis on the necessity for maintaining an acceptable level of power output.

15. HOLDING PHASE. Effective ice protection of an entire

aircraft during holding procedures may become the most critical consideration for design of the ice protection systems. The continual growth in numbers of aircraft operations imposes further air traffic burdens at terminal areas where holding is often necessary. Consequently, the selection of suitable altitudes to avoid or reduce the

severity of icing becomes more difficult with these increasing operations.

SECTION 4. OTHER FACTORS

SECTION 4. OTHER FACTORS

16. ICE SHEDDING. When ice is shed during or after an ice

encounter, it may create a hazard by entering engine inlet ducts or by striking and damaging other parts of the aircraft. The aircraft design should consider these hazards and appropriate steps should be taken to prevent unwanted buildup and release of large pieces of ice that could cause

hazardous malfunctioning or substantial damage to the engine or aircraft. Maximum ice shedding usually occurs after an ice encounter when the aircraft is flown into outside air temperatures above freezing. Ice can be expected to be shed from wing and empennage leading edges, windshields, the fuselage nose, pitot masts, antennae, propellers, rotors,

etc. Engine inlet ducts and other parts of aircraft located in the path of released ice are susceptible to ice

damage. Experience indicates that small turbine engines are more sensitive to compressor blade damage and adverse engine operation during ice ingestion than are the larger turbine

engines.

17. ICE SHAPES.

a. The critical shapes that can be expected to form on

unprotected surfaces can be established by flight tests in natural ice conditions, if the critical temperature LWC and drop size associated with these shapes can be

found.

b. Ice shapes vary with the above factors as well as with

airfoil sweep, thickness, and angle of attack.

c. Extensive natural icing and icing tunnel experience has

been documented and correlation of laboratory ice shapes with ice shapes observed under natural conditions on a specific airfoil is reasonable.

d. The effects of the maximum shapes and all lesser

quantities and shapes of ice on the aircraft flight

characteristics should be investigated. This investigation should not be limited to analysis, but should include a demonstration of a capability for continued safe flight and subsequent landing. A flight demonstration of an aircraft equipped with artificial

ice shapes can be dangerous if approached with

insufficient caution.

e. Wind tunnel and/or dry air flight tests with ice shapes

should be utilized. If an ice shape that is most critical for both handling characteristics and performance can be determined, then it is only necessary to flight test the most critical shape; otherwise, various shapes should be flight tested to investigate

the aircraft's controllability, maneuverability, stability, performance, trim and stall characteristics for all combinations of weight, c.g., flap and landing

gear configurations. Where practicable, the most critical ice shapes should be tested in combination with all other expected ice accretions to determine the full impact on aircraft performance.

18. UNPROTECTED SURFACES.

a. Aircraft normally include surfaces on which ice will

accumulate and for which no ice protection is provided. The airplane will be able to operate safely under the specified icing conditions only if the effect of ice

accumulation on these surfaces has been shown not to

introduce a hazard.

b. To establish the airplane's tolerance to the continuous

accumulation of ice on unprotected surfaces, flight tests should explore stratiform icing clouds (continuous

maximum Fig. 1) for a period of time representative of today's air traffic "holding" conditions. The "holding" configurations of the airplane (flaps, gear, drag devices) and recommended speed range should be explored and defined. It is recommended that the tests include a

continuous exposure for at least 45 minutes. If the handling characteristics are found to deteriorate below those specified for stability and control, the airplane

certification limitations should state the maximum holding time. A precautionary note should be provided in the airplane flight manual to warn the crew of the

possibility that, during prolonged encounters, ice

buildup on the unprotected surfaces may not be visible to the crew.

c. NOTE: There is usually some unprotected protuberance or

surface visible to the crew, such as windshield wipers, pod pylons, landing lights, which could serve (by location and ice dimension) as an ice datum. If there

is no protuberance normally visible to the crew, it would be helpful to provide one for this purpose.

CHAPTER 3. DESIGN ANALYSIS

CHAPTER 3. DESIGN ANALYSIS

19. GENERAL.

a. The overall objective of the design analysis should be

that no combination of meteorological conditions in the FAR 25 envelopes coupled with any engine-airplane operational condition in the airplane operational envelope will result in an accumulation of ice on

any surface which will cause an unsafe operating condition.

b. Different design approaches are needed for both airframe and powerplant (engine or engine and propeller) ice

protection systems. Aircraft surfaces may be more tolerant to ice accretion than engine and engine inlet surfaces, and the design approach applied to an airframe system may differ somewhat from those applied to an engine system. The airplane operational envelope can be precisely defined but the engine and propeller operational envelopes should consider all possible applications and installations. An aircraft surface's

greater tolerance to ice accretions should be demonstrated before omitting all possible applications

and installations from the performance envelope. Airframe systems may be designed for either complete

evaporation or running wet operation in continuous maximum conditions provided an exposure to such conditions followed by an exposure to an embedded intermittent condition will not cause an unsafe condition to develop. Engine inlets and associated airframe ducting should meet the same general

meteorological design criteria.

c. Design margins for each system will be established by

the simultaneous consideration of meteorological factors, airplane-engine operational factors, and any other pertinent factor which might be involved.

d. The most critical conditions applicable to the design of

engine inlet and propeller systems should be developed from a consideration of the entire array of meteorological and operational conditions within the operational envelope of the engine. Design points should be sufficiently defined in terms of

meteorological and operational factors for the agency to

determine how the severity of these factors was established. The determination of the most critical conditions should be made with a specific design objective in mind. An evaporative system may be permitted to run wet under some conditions, and some ice buildup may be acceptable if safety of flight is not

jeopardized.

e. The frequency and duration of icing encounters also

determine the severity of the conditions for which a system should be designed. Continuous maximum conditions interspersed with intermittent maximum conditions occur in the U.S. and other areas of the

world, and international usage of airplanes dictates the need for a design to cover this situation.

f. For design purposes, different areas of the aircraft may

require a different approach on the basis of the tolerance to ice accumulation without resulting hazard.

20. AIRFRAME SURFACES, WINGS, EMPENNAGE, CONTROL SURFACES, ETC.

a. A choice should be made in the early design stages of

the icing system to determine which portion of these areas should be protected. Those surfaces of the

airplane directly exposed to stagnation flow conditions

usually accumulate the largest quantity of ice. These include the radome, wing and tail surface leading edges,

radio masts, air scoops, etc. Leading edge high-lift devices should receive special attention because of

their location and functional importance. The selection of the surfaces to be protected is made after a careful consideration of the most severe meteorological and operating conditions, the probable extent of ice accumulations on exposed surfaces, the effects of such accumulations on lift, drag, and controllability of the aircraft, and the operation of aircraft systems. Consideration of climb, cruise, hold, descent, and

approach performance should be provided under operating conditions specified. Some ice buildup may be tolerable on some surfaces if the airplane has sufficient power or

thrust to offset the additional lift and drag forces and no unsatisfactory operating condition results. Control surfaces may be more critical than airframe surfaces in

this respect. The extent of the icing protection needed for various air scoops is directly related to the need for such protection to maintain satisfactory operation of an essential system.

b. After the extent of protection has been determined, a

heat balance between the heat "Q sub R" required and the

heat "Q sub A" available should be reached. "Q sub R" required is determined by the type of system chosen (evaporative or running wet), the quantity of water impinging on the surface, temperature of the water and air mixture, and the external flow field around the surfaces. Q sub A available is determined from an analysis of the engine bleed flow and temperature

conditions, at the most critical operating condition.

For electrical systems, the power required for the heat input must be determined.

c. The choice between a de-icing and an anti-icing system

may be influenced by an assessment of such factors as effect of shedding ice onto other surfaces or engine inlets, the complexity of a cyclic system, and the availability of a sufficient quantity of heat. The power requirements for electrical ice protection systems may influence the choice between cyclic and non-cyclic systems, areas covered by each, and the interval of the

cycle. After due consideration of the foregoing design factors, the manufacturer can establish the airframe system design points in terms of LWC, droplet diameter,

and temperature together with those factors necessary for the agency to determine by tests that all design

objectives have been met.

d. The following charts illustrate, but should not limit,

the meteorological conditions considered in the design analysis.

CONTINUOUS MAXIMUM INTERMITTENT MAXIMUM -------------------------------------------------------------­

CONTINUOUS MAXIMUM INTERMITTENT MAXIMUM -------------------------------------------------------------­

Temp - degree F. LWC Dd Temp - degree F. LWC Dd --------------------------- ----------------------------­

32 0.8 32 2.925

14 0.6 14 2.5 -4 0.3 15 -4 1.925 15 -22 0.2 -22 1.1 … -40 .25 32 0.5 … 14 0.3 32 1.75 -4 0.2 25 14 1.45 -22 0.1 -4 1.125 25 … -22 0.7 32 0.15 -40 0.15 14 0.10 … -4 0.06 40 32 0.75 -22 0.04 14 0.50 -4 0.35 40 -22 0.25 -40 0.05 …

32 0.40 14 0.30 -4 0.20 50 -22 0.10 -40 0.05 …

The pressure altitude associated with each temperature should be selected from Figure 2 and 5.

e. In addition to the meteorological conditions under

consideration, appropriate operational parameters including such factors as speed, altitude, engine power settings, etc., should be varied over the aircraft operating envelope to determine the combination or combinations of meteorological and operating parameters which result in the most critical design point or

points. Because of the large number of variables involved in these design considerations, more than one critical design point may exist for both intermittent

maximum and continuous maximum meteorological conditions.

f. The design analysis should indicate that no hazardous

quantity of ice will form on the surfaces under

consideration when exposed to intermittent maximum and continuous maximum icing conditions consistent with the

operational needs of the aircraft.

21. ENGINE INLETS, WINDSHIELDS, AND INSTRUMENTS.

a. The accumulation of ice on the engine inlet nose cowl,

bulletnose, and other areas of the aircraft which could affect engine operation is generally more critical from the standpoint of continued safe operation than ice accumulation on aircraft surfaces discussed in item 20

above. Design meteorological conditions remain the same, but operational conditions, particularly with

respect to the surface flow conditions, may vary considerably. Although a fixed-engine operational condition is assumed for design of the airframe icing system, engine airflow may vary considerably during a relatively stable airplane operational condition. This is due in part to the variation in airplane response to changes in engine thrust or power output. This lag or

variation is a factor in the determination of the most critical conditions for these areas of the airplane. Long curved inlets are particularly susceptible to snow, slush, and ice crystal impingement on the curved surfaces. Vortex generators or other boundary layer control devices should be evaluated to determine the effects of ice accumulations on these surfaces.

b. The most probable engine operational mode associated

with a particular airplane operational mode is normally the basis for the design of airframe icing systems. However, due consideration should be given to the need

for increased reliance on engine thrust or power output

during severe icing conditions and to the possibility that the engine may be actually operated through a wide range of power settings during such an encounter.

c. Ice protection should be provided for all instruments

essential for safe operation of the airplane which are subject to ice impingement or to runback and refreeze. The functioning of essential static ports should not be adversely affected by ice accumulation, freezing of

runback water from forward surfaces, or water and slush from the landing gear during takeoff and landing. It is possible that slush ingestion and water, ingested at a

lower altitude, might freeze when the airplane ascends to higher altitudes and lower temperatures. Some of the instruments that might be affected are pitot tubes, EPR

total pressure probes, and certain types of stall

indicators. These instruments are generally protected by electrical resistance systems because of the small

areas involved and the need to maintain ice-free operation in all icing conditions.

d. The forward surfaces of windshields should be protected

to provide visibility during the most severe icing conditions. While these surfaces are generally protected by electrical resistance systems because of

small areas involved, there is also the need to require duplication to maintain ice-free operation in all icing

conditions.

e. The techniques for determining the most critical design

points are similar to those previously discussed in item

20.

(1) The design analysis should indicate that the engine

inlet ice protection system will preclude the formation of any ice which could adversely affect

continued safe engine operation or cause serious

loss of power when exposed to the meteorological conditions as defined in Appendix C of FAR 25 in

combination with the aircraft operational needs and aircraft envelope.

(2) Engine inlets are frequently designed to be

evaporative under continuous maximum icing conditions and running wet under intermittent maximum conditions. Service experience indicates

that this approach has been satisfactory provided adequate precautions are taken to prevent hazards due to possible runback and refreeze.

22. ENGINE AND PROPELLER SYSTEMS. In defining the most severe

conditions for the design of icing systems for the engine, propeller, and related components, the manufacturer should not only give consideration to the icing envelopes in Figures 1, 2, 4, and 5 of Appendix C to FAR 25, but to the entire environmental and operational envelopes.

a. Engine.

(1) The engine icing system should be designed to cope

with the most severe meteorological conditions occurring simultaneously with the most severe engine and/or propeller (if applicable) operational conditions. Critical design points for both

continuous maximum and intermittent maximum conditions should be developed. Procedures for

determining water catch rate, impingement data, Q sub A available, and Q sub R required are similar

to those previously discussed for aircraft systems. The flow field around engine surfaces should be

based on the pressure and velocity relationships of the air flowing through the engine.

(2) The principal differences in the design approach

applicable to airframe and engine systems arise

from the need for reliability of the engine during severe icing encounters to insure that an aircraft

will have sufficient power to enable it to continue flight to an area of less severe meteorological

conditions.

(3) Although the engine manufacturer generally may have

some idea of the eventual application of his

engine, he cannot be sure that some future application will not be totally different from that planned. Therefore, the ice protection system should not be limited to a specific application or specific airplane operational envelope.

(4) In addition to the foregoing, the buildup of ice on

unprotected surfaces of the aircraft and the aircraft operational conditions during an icing

encounter place further emphasis on the necessity for reliable engine performance. Engine struts,

nose cones, and inlet guide vanes, if unprotected, may be subject to accumulating excessive ice deposits. When heated surfaces are employed for keeping these surfaces free of ice, the possibility of runback and refreezing should be considered. The first-stage fan or compressor blading of axial

flow engines should also be evaluated for possible

ice accumulation, with the ice protection system operating, when provided, but usually they are

minor due to the centrifugal forces present. The

larger fan blades may, however, develop accumulations at low r.p.m. near the blade root

areas. It is not considered essential to eliminate ice buildup at the engine face, but any ice buildup allowed on an operating engine should be kept to a

minimum to prevent possible damage from ice

ingestion and to ensure reliable engine operation.

(5) An accumulation of ice on any engine surface would

be considered unsafe if it caused a serious loss of power or thrust, caused airflow disturbances which

excited harmonic compressor or fan blade frequencies, became large enough to cause serious engine damage when ingested, caused damage to adjacent structure or engine components when detached by centrifugal force from rotating surfaces, caused an unbalance of rotating

components which produced vibrations greater than those for which the engine had been approved, caused damage due to reduced clearance between rotating and stationary components, or caused any

other erratic engine operation.

b. Propeller.

Propeller operation would be considered unsafe if an accumulation of ice caused a serious loss of thrust

horsepower, caused an unsafe engine condition to develop, caused damage to adjacent structure when

detached by centrifugal force, caused vibrations which could result in engine or structural failure, or caused any other erratic engine, propeller, or airplane

operation.

23. SUMMARY OF RECOMMENDED DESIGN PROCEDURES. In summarizing

the procedures for developing a design analysis, an approach

similar to the following may be utilized:

a. Choose a sufficient number of airplane and engine

operational conditions to cover that portion of the operational envelope which lies within the meteorological envelopes of Figures 1, 2, 4, and 5 of

Appendix C to FAR 25.

b. For aircraft, develop appropriate engine and propeller

(if applicable) operational conditions associated with each airplane operational condition.

c. Determine the flow field around the surface under

consideration.

d. Select adequate sets of meteorological values in terms of LWC, Dd, and T for both continuous and intermittent

conditions sufficient to cover the entire applicable range of values in Figures 1, 2, 4, and 5 of Appendix C

to FAR 25, and establish the water impingement rate on the various areas of the surface under consideration.

e. Determine surfaces requiring ice protection.

f. Determine the "Q sub R" required to satisfy the system

demands.

g. Determine "Q sub A" available for the system under

consideration.

h. On the basis of the various items above, predict system

performance including surface temperatures.

i. Those combinations which result in the most marginal

surface temperatures establish the critical design

points.

CHAPTER 4. TESTS

CHAPTER 4. TESTS

SECTION 1. GENERAL

24. GENERAL.

a. The considerations of meteorological and operational

factors were discussed in Chapters 2 and 3 to indicate how the performance of an icing system can be predicted from an analysis of a combination of these factors. Chapter 4 outlines procedures for testing ice protection systems in terms of these factors.

SECTION 1. GENERAL

b. Assuming that a system has been designed in accordance

with the foregoing design approach that the design points can be justified as being the most severe, testing at the design points is all that would be required to show compliance with the regulations. Tests

should be adequate to verify the manufacturer's analysis and selection of critical design points.

SECTION 2. TEST METHODS

SECTION 2. TEST METHODS

25. NATURAL ICING FLIGHT TESTS.

a. One of the best methods for determining the performance

of any aircraft ice protection system is to subject the

aircraft and the protection system to natural icing conditions and to demonstrate that the airplane can be safely operated while exposed to the icing conditions defined by Figure 1 and Figure 4 of Appendix C to FAR

25. Natural icing tests are required prior to certification for operation in icing conditions.

b. For flights in search of icing conditions, it is

preferable to select the geographical area and seasonal period and to watch the weather map for the desired wind

direction, velocity, cloud condition, and temperature. Efforts should be made to find an area where air traffic will permit step climbs through stratoform

clouds to seek out the high LWC level of the cloud.

c. Ice formation resembling those produced in icing tunnels

(within the area of the envelope bounded by LWC of 0.3 to 0.55, with drop size of approximately 20 microns, and in a temperature range of 26 degrees F. to 30 degrees

F.) has been observed on many occasions within a very narrow altitude range (200 to 500 feet). This sometimes occurs just below a temperature inversion altitude where there is a mild underrunning of cold air (lifting warm

air).

d. The flight test aircraft should have instrumentation to

determine liquid water content and droplet size or a means of determining ice accretion rate and the extent

of impingement from which these parameters can be established. Rotating cylinders, calibrated in an icing tunnel, have been employed but with mixed success because of boundary layer variations and difficulty with storage. A calibrated liquid water content indicator can be used to determine liquid water content. Drop size can be approximated from the extent of impingement

on any shape with known impingement characteristics or

by other acceptable means. Oil slides have been used with some success with carefully controlled procedures

and correlation when feasible with other techniques.

e. State-of-the-art airborne icing measurement

instrumentation, however, has shortcomings. A simple but imprecise indicator of the liquid water content and drop size values of Figure 1 in Appendix C is the observation and photographing of ice buildup on an

unprotected surface and correlation (corrected for velocity) with similar buildup under measured conditions in an icing tunnel. When the conditions of Figure 1 have been obtained, the airplane should be investigated for handling qualities to explore the effect of ice

accretion on the unprotected surfaces.

f. For an airplane of new design (planform) and for aft

mounted engines, where ice shedding from the wing leading edge can cause engine damage or flameout, the

aircraft flight test program should require determination of the effects of ice shedding.

g. Finding cumuliform icing conditions of Figure 4 severity

involves seasonal, geographical, and time of day

considerations. Experience indicates that the most representative and readable condition will occur:

(1) In a mild cold front system with "building" cells.

(2) Over generally flat terrain.

(3) With warmer moist air reaching the freezing level

between 8,000 to 12,000 feet.

(4) Flying parallel to the front through a series of

altitudes.

This type of frontal system usually provides an escape route to the sunny side for qualitative evaluation and photography of ice shapes and dimensions.

h. Conditions to be avoided because of hazard or lack of

useful data are:

(1) Late afternoon highly active line squalls.

(2) Snow and hail.

(3) Central U.S.A. in "tornado alley."

(4) Contour holes on airborne radar.

i. The value of natural icing flight tests can vary with

the following:

(1) Correlation of test results with analysis

predictions.

(2) Ability to compare with previous designs.

(3) Extent of icing tunnel tests as basic criteria.

(4) Extent of successful correlation of flight skin

temperature surveys in dry and wet air full-scale tests with similar shapes and temperatures investigated in the icing tunnel.

(5) Correlation of natural icing test buildup on

representative or known sections with icing tunnel shapes, considering correction for time and

airspeed.

(6) The absence of unprotected ice-catching

protuberances, such as antennas, scoops, struts,

etc.

26. DRY AIR FLIGHT TESTS. Dry air flight tests can be used to

verify many of the design objectives of an icing system. These tests may be conducted as a preliminary to natural icing tests to check the function and performance of all system components and compatibility of systems. Calculated engine bleed air mass flows for developing thrust setting curves can be verified, and models of predicated ice shapes can be installed on unprotected surfaces and evaluated in

terms of lift, drag, and controllability factors of the airplane. An analysis of heat requirements and availability at various operational conditions can be performed from data

collected during dry air tests.

27. FLYING TANKER TESTS. Flying tanker tests have been used

chiefly by the military to verify satisfactory operation of icing systems in simulated icing conditions. Equipping an

airplane for this type of test can be very expensive for a manufacturer in terms of the actual time such equipment would be used in a certification program, and the limitations of such equipment in simulating an actual icing

encounter. Turbulence, inability to expose the complete airplane to icing conditions at a given time, and problems in calibrating the LWC and droplet size of the tanker spray are some of the difficulties encountered with tanker tests.

Droplet size has not been easily controlled by spray rigs, nor has liquid water content been easily determined. LWC produced by the spray rig is a function of the distance between the test airplane and the rig since the water disperses very quickly. For these reasons, such tests are not generally considered adequate for showing full

compliance with the regulations.

28. SELF-CONTAINED SPRAY RIG TESTS.

a. Certain areas or test sections of airplane icing systems

can be tested by installing spray rigs on the airplane in such a manner as to cause impingement on the surfaces during flight. Some of the limitations applicable to

tanker tests also apply to spray rig tests. Test rigs of this nature are expensive to develop and install on

test aircraft.

b. An additional advantage of this type of testing is the

ability to control the distance between the spray section and the test section. The downstream meteorological environment produced by an artificial spray cloud is a function, among other things, of the distance between the test section and the spray rig

producing the cloud.

c. The major disadvantage of this method is the possible

disruption to the flow field around the test surface due to the presence of the rig itself. This feature may produce unrealistic impingement characteristics which are difficult to evaluate. The size and weight restrictions of the spray rig structure also limit the area that can be subjected to the spray. Because of the limitations of this test method, it is not generally considered adequate for showing full compliance with the regulations; however, this does not eliminate its use as a development tool or for testing relatively small areas for icing.

29. ICING TUNNEL TESTS. Icing tunnel tests are perhaps the

least expensive and most accurate method for determining the

performance of an icing system under various conditions.

There are several icing tunnels in existence which have the capability to control LWC, droplet size, and temperature conditions quite accurately over their range of capabilities. The advantages of ice tunnel test facilities are their ability to control the meteorological conditions through a range of values, to simulate a variety of operational conditions, and to measure performance quite

accurately. Instrumentation is generally more extensive and accurate than flight test instrumentation. The disadvantages of ice tunnel tests are their inability to simulate altitude effects or the effects of ice

accumulations on unprotected surfaces, and their inability to provide the combined operational and meteorological conditions that exist during an icing encounter of the full

scale airplane. Turbulence, sidewall effects, size, and scaling factors can be problems in ice tunnel tests. Most tunnels are very small and obtaining aerodynamic and thermodynamic similarity for models of large components can be difficult. A dimensional analysis of the aerodynamic and

thermodynamic parameters which describe the full-scale system should be undertaken prior to model tests to assure

similarity between the full-scale and model-scale systems. Full-scale values may be determined from natural icing

flight tests, dry air flight tests, spray rig tests, tanker tests, or any combination of these tests.

30. COMBINATION OF METHODS. Flight tests in natural icing

conditions under design point meteorological and operational conditions provide the most desirable method for showing

compliance with the regulations. For substantiation, however, a combination of methods may be necessary. The most desirable combination of methods would usually comprise

icing tunnel tests at the design points, with dry air and natural icing tests of the full-scale system under actual flying conditions. Data obtained by the flight tests can be

used to verify the manufacturer's analysis and ice tunnel data. The flight tests should also assure that no severe operational or design deficiency exists.

31. ICE SHEDDING.

a. The path of ice released from the aircraft is affected

by many variables, such as ice shape and density, aircraft attitude and altitude, airspeed, air flow, manner in which the ice is released, etc. Therefore, it may be difficult on some configurations to show that ice released will not enter into engine inlet ducts or strike and damage other parts of the aircraft. A

desirable approach for resolving an apparent "ice shedding" problem is to install anti-icing provisions in

critical areas. The same procedures used to substantiate other aircraft anti-icing systems are

applicable.

b. If anti-icing provisions are not installed in critical

ice shedding areas, then investigations should be conducted to show that ice which sheds off of the

aircraft will not cause an unsafe condition. "Ice

shedding" investigations should be made during and after ice encounters. Sufficient encounters in all intended

operation conditions should be made to assure there is

no hazard associated with the release of ice. In addition to the usual measurements and observations made during ice encounter tests, the following additional instrumentation and/or observations are suggested:

(1) Motion pictures to record the trajectory of ice

released from the aircraft.

(2) Photopanel for turbine-engine-powered aircraft to

record EGT, EPR, and RPM for the purpose of detecting adverse effects on engine operation.

(3) Visual examination of the aircraft for damage

before and after ice encounters, especially in the area of the engine compressor and inlet.

SECTION 3. TEST PROCEDURES

SECTION 3. TEST PROCEDURES

32. AIRFRAME SURFACES (WINGS, EMPENNAGE, CONTROL SURFACES,

ENGINE INLETS, WINDSHIELDS, AND INSTRUMENTS, ETC.) SYSTEMS.

a. Ice Tunnel Tests.

(1) For ice tunnel tests of these areas, design point values of LWC, Dd, and T should be established in

the tunnel at the pressure, temperature, velocity, etc., defined by the design operational conditions. Models should be designed to assure that Reynolds numbers and other dimensionless parameters are maintained as closely as possible to the full

scale value. They should be mounted to simulate the flight attitude associated with the most severe

conditions. If flaps or other devices are used to produce the proper flow field conditions,

instrumentation should be provided to show that test and design values are in general agreement. In an ice tunnel test of an evaporative system, all of the impinging water should evaporate. In an ice

tunnel test of a non-evaporative or running wet system, the predicted amount of runback water should not be exceeded and any ice that forms on critical surfaces should be within the limits predicted in the design analysis and confirmed as

acceptable by flight tests.

(2) Liquid systems tested in an icing tunnel should

preclude ice formation on the protected surfaces for the designed period of protection with flow of

temperature depressant fluids within the design

value.

b. Tanker or Spray Rig Tests. Tanker tests have been

useful as a development tool but can be dangerous or produce misleading results because of sharp variations in the water cloud and catch that come with changes in

distance behind the tanker. Spray rig tests of full scale aircraft may be used in the substantiation of the critical design points, provided the spray can be calibrated to produce the design LWC and droplet

diameter and the tests are conducted under flight conditions representative of the design point

conditions.

c. Dry Air and Natural Ice Tests.

(1) Dry air and natural icing tests of full-scale

aircraft should be conducted as closely as possible

to design point conditions to reduce the uncertainty associated with extensive extrapolations. These tests should demonstrate the effectiveness of the icing system under natural

conditions. The tests should also provide the means by which the buildup of ice on running wet

and unprotected surfaces can be evaluated with respect to the engine operational characteristics

and with respect to the lift, drag, and controllability of the airplane. Ridges on models simulating predicted ice accumulations should be installed on full-scale aircraft during dry air

flight tests to show that these accumulations will not cause an unsafe aerodynamic condition.

(2) The natural icing tests should demonstrate that no

hazardous accumulations of ice occur which could cause an unsafe condition to develop when icing is encountered. Sufficient testing in natural ice conditions should be accomplished to confirm

assumptions made in the manufacturer's analysis and to establish that the extrapolations are accurate

within acceptable limits.

33. ENGINES.

a. General.

(1) For complying with FAR 33.67, the icing conditions

defined by charts in Appendix C of Part 25 are given as the general flight icing conditions which may be encountered. The Appendix C charts cover such a wide range of conditions and combinations of

the various icing parameters that numerous data test points would seem to be indicated. However, experience with turbine engines has indicated that the critical conditions can be covered adequately by engine icing tests covering only a few specific

conditions coupled with acceptable analyses, dry

air tests, rig tests, or experience with similar engines.

(2) The U.S. military services, for many years, have

been qualifying engines to two specific conditions for sea level testing. Compliance with military testing has been accepted for FAA engine certification in several instances and has provided

acceptable results. Recent experience has indicated the desirability of considering the effects of a ground icing fog, which may cause an

unsafe condition due to excessive ice accumulation in prolonged ground operation at low-power

settings. The following guidelines are provided to assist in establishing acceptable testing programs and to promote uniform levels of compliance.

(3) Engines requiring ice protection systems should

have the capability of de-icing the protected surfaces, as it is generally assumed that icing

conditions may be encountered in operation without

immediate recognition of the fact by the pilot. In the event a satisfactory automatic anti-icing system actuation control is provided, this matter

may be recognized; however, current engine protection systems employ manual actuation, necessitating the de-icing capability. A one-minute actuation delay is assumed to cover the probable delay in system actuation.

(4) Engines whose features inherently preclude adverse

ice collection and buildup at all times do not require de-icing or anti-icing systems.

b. Acceptable means of compliance.

(1) The engine should be capable of operating

acceptably under the meteorological conditions of Appendix C of FAR 25 over the engine operating

envelope and under conditions of ground fog.

(2) Experience has indicated that testing to the points

set forth in the following table and schedule has been considered a successful means of showing

compliance if used in conjunction with the critical conditions determined in the design analysis.

Icing Condition 1 2 3 --------------------------------------------------------------­

Liquid Water Content, gr/(meter cubed) 2. 1. 2.

Atmospheric temperature, degrees F. 23. -4. 29.

Mean effective water droplet diameter, microns 25. 15. 40.

minimum

(a) Operate the engine steadily under icing conditions

1 and 2 for at least 10 minutes each at takeoff setting, 75 percent and 50 percent of M.C. and at flight idle setting, then accelerate from flight

idle to takeoff. If ice is still building up at the end of 10 minutes, continue running until the

ice begins to shed or until the engine will no longer operate satisfactorily.

(b) Operate steadily at ground idle setting for at

least 30 minutes under icing condition 3 followed by acceleration to takeoff setting.

(c) While at cruise and flight idle, for engines with

icing protection systems, operate for at least one minute in the icing atmosphere prior to turning on the icing protection system.

(3) Engine operation in these icing conditions should be

reliable, uninterrupted, without any significant adverse effects, and include the ability to continue in operation and accelerate. Some power reduction is acceptable at idle power settings but all other

operation should be unaffected.

(4) Special consideration and tests should be conducted to

adequately substantiate:

(a) Engines with inlet screens.

(b) Engines with air passages which might accumulate

snow or ice due to restrictions or contours.

(c) Unprotected surfaces upon which ice may build up in

rare instances to significant degrees for longer

exposures than specified above.

34. HELICOPTER ENGINE INLET AND ROTOR. If comparative testing

of the engine inlet and the rotor system is to be used to establish equivalent safety, it should be conducted under

conditions which provide known values for water content, droplet size, and temperature. However, cloud horizontal extent need not be considered if it can be positively established that all icing conditions which result in significant ice accretion on the engine inlet also result in

intolerable ice accumulations on the helicopter rotors. Sufficient variations of the icing parameters should be

investigated to assure that the condition found critical for the engine inlet is also critical for the rotor system.

Experience has shown that at high ambient temperature (above 25 degrees F.) rotor ice shedding occurs at time intervals which prevent ice buildups.

SECTION 4. FINDING ICING CONDITIONS FOR TEST PURPOSES

SECTION 4. FINDING ICING CONDITIONS FOR TEST PURPOSES

35. GENERAL

a. Aircraft icing has been the subject of a great deal of

discussion, but actual operational encounters with icing

conditions have been rarely documented. Scheduled flight operation in icing conditions is not unusual, while finding natural icing conditions for testing aircraft ice protection systems can be a problem during aircraft certification programs. For example, after a fruitless search for icing conditions in the Northwest during the month of February, the test aircraft accumulated a heavy buildup of ice on a letdown to home base.

35. GENERAL

b. In another related experience, it was reported that on a flight between Shannon and London in a stratoform cloud

at 6,000 feet (temperature 28 degrees F. to 30 degrees F.), a very heavy accumulation of ice was observed on

the unprotected surfaces. The captain (with 20,000+ hours flying time) stated that it was the heaviest ice accumulation he had ever seen. Another altitude was requested but it was denied because 3,000 ft., 4,000 ft., and 7,000 ft. altitudes were occupied. Airplanes at other altitudes reported only a trace of ice.

c. These experiences and others support the contention that

ice intensity corresponding to Figure 1, Appendix C, is

confined to a small vertical segment of the atmosphere and that one could look a long time at other altitudes

and honestly report that "we could not find ice."

d. In another cited instance, two Convair 240's aircraft,

one northbound and one southbound, were using the same airway over Philadelphia at 1,000 feet vertical

separation. The northbound airplane encountered severe ice, while the southbound encountered just a trace of

ice.

e. The operational pilot and the test pilot have no way of

predicting or seeing the level at which high accretion

rate would be encountered. One would like to avoid it and the other wants to find it. The solution for both

is the same. If possible, change altitude.

f. The test group should make arrangements to "work" an

area where an altitude band can be cross-sectioned;

otherwise, time could be needlessly wasted.

g. The rate of accretion, ice shape, and ice hardness

varies over the envelopes of Figures 1 and 4 of FAR 25, Appendix C. Figures 1, 2, 4, and 5 are a compilation of

service experience and icing tunnel data which define the likely areas in nature where ice would be

encountered.

h. Ice accretion will occur on any object moving through a

cloud when the temperature is below freezing.

(1) The rate of ice buildup will vary with:

(a) The water density of the cloud, i.e., liquid

water content.

(b) The velocity of the object.

(c) The size and shape of the object.

(d) The temperature of the air and the temperature

of the object.

(e) The temperature of the water drops.

(2) The shape and consistency of ice buildup will vary

with:

(a) Temperature of the object, the cloud, and the

water drop.

(b) The velocity of the object, as it (the

temperature rise) affects the surface temperature.

(c) Thickness ratio of the object and "sweep" with

respect to the free stream.

These items have been listed to emphasize the fact that ice accretion on unprotected portions of the airplane, or on wing and tail surfaces with anti-icing/de-icing system turned off, varies with the factors previously mentioned. Ice buildup observed by the flight crew on various parts of the airplane may be compared with NACA ice tunnel data accumulated under controlled conditions of liquid water content and droplet size. The flight crew can also estimate the icing intensity of the

stratus cloud they are exploring and determine whether they are actually traversing FAR 25, Appendix C,

conditions. If they are not collecting ice at the desired rate, they should move to another altitude in search of the high water content level.

36. FINDING ICE IN STRATOFORM CLOUDS. The following conclusions

are based on practical experience and success in finding icing conditions in stratoform cloud conditions:

a. The water catch rate or ice accretion rate will decrease

with decreasing temperature below +32 degrees F.

b. Dense stratoform clouds being lifted to higher altitude

over rising terrain occasionally have LWC higher than required. Flight over mountainous terrain should be avoided because of inconsistencies in the relationship

between liquid water content and temperature.

c. For given temperature, the shape of the ice accretion

will vary with droplet size.

d. Conditions approaching rain, such as large drops

spattering on the windshields or intermittent sharp increase in catch rate, should be avoided. These conditions indicate that there is a rain-producing cloud above the stratoform cloud and that intermittent (Figure

4) conditions are being encountered.

e. It should be recognized that the variation in LWC with

temperature (for a given drop size) in Figure 1 is an

expression of the predicted variation of cloud density with temperature. One should choose what is believed to be critical temperature for the type of protection

system involved.

f. Icing conditions of the intensity of Figure 1 frequently

occur in very moist air masses blowing inland from warmer seas, such as the Gulf of Mexico, the Japan

current, and the Gulf Stream.

g. The super-saturated clouds lift and cool as they move

over the land mass. Random seeking of ice is time consuming and wasteful. Adequate planning will increase the chance of success. It is advisable to wait until

the weather map shows the correct direction of air movement, heavy clouds over a large area, and freezing level at 6,000 to 8,000 feet; then crisscross the area in step climbs.

37. FINDING ICE IN CUMULIFORM CLOUDS.

a. The meteorological condition which yields reasonably

consistent icing can be found in a mild or building

(cold) frontal system.

b. The weather map, the patience to await the formation of

icing conditions, the ability to start the flight on short notice, and airborne weather radar are the best tools to locate this condition.

c. Intense line squalls should be avoided, such as those

prevalent in "tornado alley" in central U.S. and all

"contour holes" in radar. These conditions contain extreme vertical air currents, which produce large variations in LWC, drop size, and temperature. The ice catch in severe line squalls will probably be very erratic and conditions change so rapidly that

instrumentation is useless.

d. Also, it is best to avoid mountainous areas, because the

mechanical lifting causes erratic vertical variations in temperature and only complicate finding the correct altitude (temperature).

e. Fall and early spring are generally the best seasons to

find ice. Excessive snow usually occurs in winter and

hail usually occurs in summer. The ideal cold front can provide the opportunity of making runs at a series of

altitudes parallel to the front and yet provide an escape route to the sunny side to photograph unprotected portions or ice-measuring rods.

CHAPTER 5. SUMMARY OF RECOMMENDED PROCEDURES FOR TYPE CERTIFICATION

CHAPTER 5. SUMMARY OF RECOMMENDED PROCEDURES FOR TYPE CERTIFICATION

38. AIRFRAME MANUFACTURER. The airframe manufacturer should

submit a design analysis which has as its prime objective the determination of the critical design points and the prediction of performance of protective systems for those

areas of the airplane for which he has certification

responsibility. The selection of these points should involve consideration of all the factors covered in this

advisory circular. The manufacturer's test proposal should be submitted and agreement reached on procedures before

testing is begun.

39. ENGINE MANUFACTURER. The engine manufacturer should submit

a design analysis which has as its prime objective the establishment of sufficient critical design points to assure that the engine can function adequately in continuous maximum and intermittent maximum conditions. The selection of these points should involve consideration of all the factors covered in this advisory circular. The manufacturer's test proposal should be submitted and test procedures agreed upon before testing is begun. Testing should be conducted at sufficient points throughout

the power or thrust range to demonstrate that no

unsatisfactory engine operational feature exists under these conditions.

APPENDIX 1. BIBLIOGRAPHY

APPENDIX 1. BIBLIOGRAPHY

1. Lewis, William and Bergrun, Norman: A Probability Analysis

of the Meteorological Factors Conducive to Aircraft Icing in the United States. NACA TN No. 2738, 1952.

2. Hacker, P.T. and Dorsch, R.G.: A Summary of Meteorological

Conditions Associated with Aircraft Icing and a Proposed Method of Selecting Design Criteria for Ice Protection Equipment. NACA TN No. 2569, 1951.

1. Lewis, William and Bergrun, Norman: A Probability Analysis

3. Mises, Von R.: Theory of Flight, McGraw Hill, 1945.

4. Kellogg, D.P.: Foundations of Potential Theory. Frederick Ungar Publishing Co., 1929.

5. Messinger, B.L.: Equilibrium Temperature of an Unheated

Surface as a Function of Airspeed. Journal of Aeronautical Sciences, Vol. 20, No. 1, January, 1953.

6. Selection of an Ice Detector for Jet and Turboprop Aircraft.

Rosemount Engineering Report No. 1688P.

7. Rays, George P.: Airborne Instrumentation System for

Measuring Meteorological Phenomena Inside Thunderstorms.

Armed Services Technical Information Agency. Technical Documentary Report No. ASD-TOR-63-231, May, 1963.

8. Trunor, Oleg Konstantinanich: Some Results of Experimental

8. Trunor, Oleg Konstantinanich: Some Results of Experimental

Flights in Natural Icing Conditions and Operation of Aircraft Terminal Ice Protection Systems. Paper presented at the International Ice Protection Conference, D. Napier

and Son, Ltd., May, 1960.

9. Vickers-Viking Fluid De-Icing Trials 1950. Published by

T.K.S. (Aircraft De-Icing) Limited, Drayton House, London. 1950.

10. O'Neil, J.E. and Ldrazil, J.A.: Investigation of Methods of

Anti-Icing Gas Turbine Inlet Components. Wright Air Development Center, Power Plant Laboratory. WADC Technical Report 56-202, June, 1956.

11. Tribus, Myron: Modern Icing Technology. Engineering

Research Institute, University of Michigan, ARDC Project M992-E, January, 1952.

12. Weiner, Frederick R.: Use of the K sub 0 Correlation in

Preliminary Design and Scale Model Icing. North American Aviation. Report No. NA-64-126, February, 1964.

13. Sogin, Harold H.: A Design Manual for Thermal Anti-Icing

Systems. Wright Air Development Center. WADC Technical Report 54-313, Dec. 1954.

14. Baxter, D.C.: A Review of Radiation Scattering Methods for

Measuring Cloud Droplet Size. National Research Council of Canada. Report No. MP-40, April, 1954.

15. Petach, Alex: A Summary of Aircraft Icing Criteria. The Boeing Co. Vertol Division.

16. Rudolph, J.D.: Outline of Tests Conducted by North American

Aviation at Mt. Washington during the 1950-51 Icing Season Project Summit. North American Aviation, Inc. May, 1951.

17. Fraser, Don: Note on the Flight Testing and Assessment of

17. Fraser, Don: Note on the Flight Testing and Assessment of

Icing Protection Systems. Low Temperature Laboratory, Ottawa, Canada. Lecture No. 12b. University of Michigan.

18. Orr, J.L.: Electro-Thermal De-Icing Systems. Low

Temperature Laboratory. Ottawa, Canada. Lecture No. 8, University of Michigan.

19. Neel, Carr B.: A Procedure for the Design of Air-Heated Ice

Prevention Systems. NACA TN 3130.

20. Authored by a Working Group of the NACA Subcommittee on

20. Authored by a Working Group of the NACA Subcommittee on

Meteorological Problems: Meteorological Problems Associated with Commercial Turbojet Aircraft Operation. NACA RM 54L29,

1955.

21. Kleinknecht, Kenneth S.: Flight Investigation of the Heat

Requirements for Ice Prevention on Aircraft Windshields. NACA RM E7G28.

22. Jones, Alun R.: An Investigation of a Thermal Ice

Prevention System for a Twin-Engine Transport Airplane.

NACA Report No. 862. 1964.

23. Lewis, William: Icing Zones in a Warm Front System with

23. Lewis, William: Icing Zones in a Warm Front System with

General Precipitation. NACA TN 1392, 1947.

24. Aircraft Ice Protection. Report of Symposium. April

28-30, 1969. Department of Transportation, Federal Aviation

Administration.

APPENDIX 2. SELECTED BIBLIOGRAPHY OF UNCLASSIFIED

NASA-NACA AIRCRAFT ICING REPORTS

NASA-NACA AIRCRAFT ICING REPORTS

Meteorology of Icing Clouds

1. Bergrun, N.R. and Lewis, Wm.: A Probability Analysis of the

Meteorological Factors Conducive to Aircraft Icing in the United States. NACA TN 2738, 1952.

2. Hacker, P.T. and Dorsch, R.G.: A Summary of Meteorological

Conditions Associated with Aircraft Icing and a Proposed Method of Selecting Design Criterions for Ice Protection Equipment. NACA TN 2569, 1951.

3. Jones, A.R. and Lewis, Wm.: Recommended Values of

Meteorological Factors to be Considered in the Design of Aircraft Ice Prevention Equipment. NACA TN 1855, 1949.

4. Kline, D.B.: Investigation of Meteorological Conditions

Associated with Aircraft Icing in Layer-Type Clouds for 1947-48 Winter. NACA TN 1793, 1949.

5. Kline, D.B. and Walker, J.A.: Meteorological Analysis of Icing Conditions Encountered in Low-Altitude Stratiform

Clouds. NACA TN 2306, 1951.

6. Lewis, Wm.: Icing Properties of Non-Cyclonic Winter

Stratus Clouds. NACA TN 1391, 1947.

7. Lewis, Wm. and Hoecker, W.H., Jr.: Observations of Icing

Conditions Encountered in Flight During 1948. NACA TN 1904,

1949.

8. Lewis, Wm., Kline, W.B. and Steinmetz, C.P.: A Further

Investigation of the Meteorological Conditions Conducive to Aircraft Icing. NACA TN 1424, 1947.

9. Perkins, P.J.: Preliminary Survey of Icing Conditions

Measured During Routine Transcontinental Airline Operation. NACA RM E52J06, 1952.

10. Perkins, P.J.: Statistical Survey of Icing Data Measured on

Scheduled Airline Flights over the United States and Canada.

NACA RM E55F28a, 1955.

11. Perkins, P.J.: Icing Frequencies Experienced During Climb

and Descent by Fighter-Interceptor Aircraft. NACA TN 4314,

1958.

12. Perkins, P.J. and Kline, D.B.: Analysis of Meteorological Data Obtained During Flight in a Supercooled Stratiform

Cloud of High Liquid Water Content. NACA RM E51D18, 1951.

13. Perkins, P.J., Lewis, W. and Mulholland, D.R.: Statistical

Study of Aircraft Icing Probabilities at the 700- and

500-Millibar Levels over Ocean Areas in the Northern Hemisphere. NACA TN 3984, 1957.

14. Perkins, P.J.: Summary of Statistical Icing Cloud Data

Measured Over United States and North Atlantic, Pacific, and

Arctic Oceans During Routine Aircraft Operations. NASA Memo CCE-169, 1959.

Fundamental Properties of Water

1. Levine, J.: Statistical Explanation of Spontaneous Freezing

of Water Droplets. NACA TN 2234, 1950.

2. Dorsch, R.G., and Hacker, P.T.: Photomicrographic

Investigation of Spontaneous Freezing Temperatures of

Supercooled Water Droplets. NACA TN 2142, 1950.

3. Hacker, P.T.: Experimental Values of the Surface Tension of

Supercooled Water. NACA TN 2510, 1951.

4. Dorsch, R.G., and Boyd, B.: X-Ray Diffraction Study of the Internal Structure of Supercooled Water. NACA TN 2532,

1951.

5. Dorsch, R.G., and Levine, J.: A Photographic Study of

Freezing of Water Droplets Falling Freely in Air. NACA RM E51C17, 1952.

6. Lowell, H.H.: Maximum Evaporation Rates of Water Droplets

Approaching Obstacles in the Atmosphere. NACA TN 3024, 1953.

7. Hardy, J.K.: Kinetic Temperature of Wet Surfaces. A Method

of Calculating the Amount of Alcohol Required to Prevent Ice, and the Derivation of the Psychometric Equation. ARC R&M 2830, 1953. NACA ARR 5G13, 1945. See also WR A-8.

Meteorological Instruments

1. Neel, C.B., Jr. and Steinmetz, C.P.: The Calculated and

Measured Performance Characteristics of a Heated-Wire

Liquid-Water-Content Meter for Measuring Icing Severity. NACA TN 2615, 1952.

2. Lewis, Wm., Perkins, P.J., and Brun, R.J.: Procedure for

Measuring Liquid-Water Content and Droplet Sizes in

Supercooled Clouds by Rotating Multicylinder Method. NACA RM E53D23, 1953.

3. McCullough, S., and Perkins, P.J.: Flight Camera for

Photographing Cloud Droplets in Natural Suspension in the

Atmosphere. NACA RM E50K01a, 1951.

4. Perkins, P.J.: Flight Instrument for Measurement of

Liquid-Water Content in Clouds at Temperatures Above and

Below Freezing. NACA RM E50J12a, 1951.

5. Perkins, P.J., McCullough, S., and Lewis, R.D.: A

Simplified Instrument for Recording and Indicating Frequency and Intensity of Icing Conditions Encountered in Flight. NACA RM E51E16, 1951.

6. Brun, R.J., Levine, J., and Kleinknecht, K.S.: An

Instrument Employing Coronal Discharge for Determination of Droplet Size Distribution of Clouds. NACA TN 2458, 1951.

7. Levine, J., and Kleinknecht, K.S.: Adaptation of a Cascade

Impactor to Flight Measurement of Droplet Size in Clouds. NACA RM E51G05, 1951.

8. Howell, W.E.: Comparison of Three Multicylinder Icing Meters and Critique of Multicylinder Method. NACA TN 2708,

1952.

9. Jones, A.R., and Lewis, W.: A Review of Instruments

Developed for the Measurement of the Meteorological Factors

Conducive to Aircraft Icing. NACA RM A9C09, 1949.

10. Neel, C.B.: A Heated-Wire Liquid-Water-Content Instrument

and Results of Initial Flight Test in Icing Conditions. NACA RM A54I23, 1955.

11. Hacker, P.T.: An Oil-Stream Photomicrographic Aeroscope for

Obtaining Cloud Liquid-Water Content and Droplet Size

Distributions in Flight. NACA TN 3592, 1956.

Impingement of Cloud Droplets

1. Bergrun, N.R.: An Empirical Method Permitting Rapid

Determination of the Area, Rate, and Distribution of Water­

Drop Impingement on an Airfoil of Arbitrary Section at Subsonic Speeds. NACA TN 2476, 1951.

2. Bergrun, N.R.: A Method for Numerically Calculating the

Area and Distribution of Water Impingement on the Leading Edge of an Airfoil in a Cloud. NACA TN 1397, 1947.

3. Brun, R.J., Serafini, J.S., and Moshos, G.J.: Impingement

of Water Droplets on an NACA 651-212 Airfoil at an Angle of Attack of 4 Degrees. NACA RM E52B12, 1952.

4. Hacker, P.T., Brun, R.J., and Boyd, B.: Impingement of

Droplets in 90 Degree Elbows with Potential Flow, NACA TN 2999, 1953.

5. Serafini, J.S.: Impingement of Water Droplets on Wedges and

Diamond Airfoils at Supersonic Speeds. NACA Rep. 1159,

1954. (Supersedes NACA TN 2971).

6. Brun, R.J., Gallagher, H.M., and Vogt, D.E.: Impingement of

Water Droplets on NACA 65A-004 Airfoil and Effect of Change in Airfoil Thickness from 12 to 4 Percent at 4 Degrees Angle

of Attack.

7. Brun, T.J., Gallagher, H.M., and Vogt, D.E.: Impingement of

Water Droplets on NACA 65(sub 1)-208 and 65(sub 1)-212 Airfoils at 4 Degrees Angle of Attack. NACA TN 2952, 1953.

8. Brun, R.J., and Mergler, H.W.: Impingement of Water

Droplets on a Cylinder in an Incompressible Flow Field and Evaluation of Rotating Multicylinder Method for Measurement

of Droplet-Size Distribution, Volume Median Droplet Size, and Liquid-Water Content in Clouds. NACA TN 2904, 1953.

9. Brun, R.J., Serafini, J.S., and Gallagher, H.M.:

Impingement of Cloud Droplets on Aerodynamic Bodies as Affected by Compressibility of Air Flow Around the Body.

NACA TN 2903, 1953.

10. Guibert, A.G., Janssen, E., and Robbins, W.M.:

Determination of Rate, Area, and Distribution of Impingement of Waterdrops on Various Airfoils from Trajectories Obtained

on the Differential Analyzer. NACA RM 9A05, 1949.

11. Dorsch, R.G., and Brun, R.J.: A Method for Determining

Cloud-Droplet Impingement on Swept Wings. NACA TN 2931, 1953.

12. Brun, R.J., and Dorsch, R.G.: Impingement of Water Droplets on an Ellipsoid with Fineness Ratio 10 in Axisymmetric Flow.

NACA TN 3147, 1954.

13. Dorsch, R.G., Brun, R.J., and Gregg, J.L.: Impingement of

Water Droplets on an Ellipsoid with Fineness Ratio 5 in

Axisymmetric Flow. NACA TN 3099, 1954.

14. Dorsch, R.G., and Brun, R.J.: Variation of Local

Liquid-Water Concentration about an Ellipsoid of Fineness Ratio 5 Moving in a Droplet Field. NACA TN 3153, 1954.

15. Brun, R.J., Gallagher, H.M., and Vogt, D.E.: Impingement of

Water Droplets on NACA 65A004 Airfoil at 8 Degrees Angle of

Attack. NACA TN 3155, 1954.

16. Brun, R.J., and Dorsch, R.G.: Variation of Local

Liquid-Water Concentration about an Ellipsoid of Fineness Ratio 10 Moving in a Droplet Field. NACA TN 3410, 1955.

17. von Glahn, U., Gelder, T.F., and Smyers, W.H.: A

Dye-Tracer Technique for Experimentally Obtaining Impingement Characteristics of Arbitrary Bodies and a Method for Determining Droplet Size Distribution. NACA TN 3338, 1955.

18. Dorsch, R.G., Saper, P.G., and Kadow, C.F.: Impingement of

Water Droplets on a Sphere. NACA TN 3587, 1955.

19. Lewis, Wm., and Brun, R.J.: Impingement of Water Droplets on a Rectangular Half Body in a Two-Dimensional

Incompressible Flow Field. NACA TN 3658, 1956.

20. Brun, R.J., and Vogt, D.E.: Impingement of Water Droplets

on NACA 65A004 Airfoil at 0 Degrees Angle of Attack. NACA

TN 3586, 1955.

21. Brun, R.J., Lewis, Wm., Perkins, P.J., and Serafini, J.S.:

Impingement of Cloud Droplets on a Cylinder and Procedure for Measuring Liquid-Water Content and Droplet Sizes in

Supercooled Clouds by Rotating Multicylinder Method. NACA Rep. 1215, 1955. (Supersedes NACA TN's 2903, 2904, and NACA RM E53D23)

22. Brun, R.J.: Cloud-Droplet Ingestion in Engine Inlets with

Inlet Velocity Ratios of 1.0 and 0.7. NACA Report 1317 (supersedes NACA TN 3593), 1956.

23. Gelder, T.F.: Droplet Impingement and Ingestion by

Supersonic Nose Inlet in Subsonic Tunnel Conditions. NACA TN 4268, 1958.

24. Gelder, T.F., Smyers, W.H. and von Glahn, U.H.: Experimental Droplet Impingement on Several Two-Dimensional

Airfoils with Thickness Ratios of 6 to 16 Percent. NACA TN 3839, 1956.

25. Hacker, P.T., Saper, P.G. and Kadow, C.F.: Impingement of

Droplets in 60 Degree Elbows with Potential Flow. NACA TN 3770, 1956.

26. Lewis, J.P. and Ruggeri, R.S.: Experimental Droplet

Impingement on Four Bodies of Revolution. NACA TN 4092, 1957.

27. Brun, R.J. and Vogt, D.: Impingement of Cloud Droplets on 36.5-Percent-Thick Joukowski Airfoil at Zero Angle of Attack

and Discussion of Use as Cloud Measuring Instrument in Dye Tracker Technique. NACA TN 4035, 1957.

28. von Glahn, U.H.: Use of Truncated Flapped Airfoils for Impingement and Icing Tests of Full-Scale Leading-Edge

Sections. NACA RM E56E11, 1956.

Propeller Icing Protection

1. Selna, J. and Darsow, J.F.: A Flight Investigation of the

Thermal Performance of an Air-Heated Propeller. NACA TN 1178, 1947.

2. Lewis, J.P., and Stevens, H.C., Jr.: Icing and De-Icing of

a Propeller with Internal Electric Blade Heaters. NACA TN 1691, 1948.

3. Lewis, J.P.: De-Icing Effectiveness of External Electric

Heaters for Propeller Blades. NACA TN 1520, 1948.

4. Perkins, P.J., and Millenson, M.B.: An Electric Thrust

Meter Suitable for Flight Investigation of Propellers. NACA RM E9C17, 1949.

5. Mulholland, D.R., and Perkins, P.J.: Investigation of

Effectiveness of Air-Heating a Hollow Steel Propeller for Protection Against Icing I - Unpartitioned Blades. NACA TN

1586, 1948.

6. Perkins, P.J. and Mulholland, D.R.: Investigation of

Effectiveness of Air-Heating a Hollow Steel Propeller for Protection Against Icing II - 50-Percent Partitioned Blades. NACA TN 1587, 1948.

7. Mulholland, D.R., and Perkins, P.J.: Investigation of

Effectiveness of Air-Heating a Hollow Steel Propeller for

Protection Against Icing III - 25-Percent Partitioned Blades. NACA TN 1588, 1948.

8. Gray, V.H., and Campbell, R.G.: A Method for Estimating

Heat Requirements for Ice Prevention on Gas-Heated Hollow Propeller Blades. NACA TN 1494, 1947.

9. Neel, C.B., Jr.: An Investigation Utilizing an Electrical

Analogue of Cyclic De-Icing of a Hollow Steel Propeller with an External Blade Shoe. NACA TN 2852, 1952.

10. Neel, C.B., Jr.: An Investigation Utilizing an Electrical

Analogue of Cyclic De-Icing of Hollow Steel Propellers with

Internal Electric Heaters. NACA TN 3025, 1953.

11. Bright, L.G., and Neel, C.B., Jr.: The Effect of the Ice

Formations on Propeller Performance. NACA TN 2212, 1950.

Induction System Icing Protection

1. Coles, W.D.: Investigation of Icing Characteristics of a

Typical Light-Airplane Engine Induction System. NACA TN 1790, 1949.

2. Coles, W.D., Rollin, V.G., and Mulholland, D.R.: Icing

Protection Requirements for Reciprocating-Engine Induction Systems. NACA TR 982, 1950.

3. Lewis, J.P.: Investigation of Aerodynamic and Icing

Characteristics of a Flush Alternate-Inlet Induction-System Air Scoop. NACA RM E53E07, 1953.

Turbine-Type Engine and Inlet Icing Studies

1. Acker, L.W.: Natural Icing of an Axial-Flow Turbojet Engine

in Flight for a Single Icing Condition. NACA RM E8F01a, 1948.

2. Acker, L.W.: Preliminary Results of Natural Icing of an

Axial-Flow Turbojet Engine. NACA RM E8C18, 1948.

3. Gray, V.H., and Bowden, D.T.: Icing Characteristics and

Anti-Icing Heat Requirements for Hollow and Internally Modified Gas-Heated Inlet Guide Vanes. NACA RM E50I08, 1950.

4. Lewis, J.P. and Ruggeri, R.S.: An Investigation of Heat Transfer from a Stationary and Rotating Ellipsoidal Forebody

of Fineness Ratio 3. NACA TN 3837, 1956.

5. Ruggeri, R.S. and Lewis, J.P.: Investigation of Heat Transfer from a Stationary and Rotating Conical Forebody.

NACA TN 4093, 1957.

6. von Glahn, U.H., and Blatz, R.E.: Investigation of Power

Re-Requirements for Ice Prevention and Cyclical De-Icing of

Inlet Guide Vanes with Internal Electric Heaters. NACA RM

E50H29, 1950.

7. von Glahn, U.H., Callaghan, E.E. and Gray, V.H.: NACA

Investigations of Icing-Protection Systems for Turbojet­

Engine Installation. NACA RM E51B12, 1951.

8. von Glahn, U., and Blatz, R.E.: Investigation of

Aerodynamic and Icing Characteristics of Water-Inertia­

Separation Inlets for Turbojet-Engine Ice Protection. NACA RM E50E03, 1950.

Wing Icing Protection

1. Hardy, J.K.: An Analysis of the Dissipation of Heat in

Conditions of Icing from a Section of the Wing of the C-46 Airplane. NACA TR 831, 1945.

2. Bergrun, N.R., and Neel, C.B.: The Calculation of the Heat

Required for Wing Thermal Ice Prevention in Specified Icing Conditions. NACA TN 1472, 1947.

3. Gray, V.H., Bowden, D.T., and von Glahn, U.: Preliminary

Results of Cyclical De-Icing of a Gas-Heated Airfoil. NACA RM E51J29, 1952.

4. Lewis, J.P., and Bowden, D.T.: Preliminary Investigation of

Cyclic De-Icing of an Airfoil Using an External Electric

Heater. NACA RM E51J30, 1952.

5. Gelder, T.F., and Lewis, J.P.: Comparison of Heat Transfer

from Airfoil in Natural and Simulated Icing Conditions.

NACA TN 2480, 1951.

6. Callaghan, E.E., and Serafini, J.S.: A Method for Rapid

Determination of the Icing Limit of a Body in Terms of the

Stream Conditions. NACA TN 2914, 1953.

7. Callaghan, E.E., and Serafini, J.S.: Analytical

Investigation of Icing Limit for Diamond-Shaped Airfoil in Transonic and Supersonic Flow. NACA TN 2861, 1953.

8. Ruggeri, R.S.: De-Icing and Runback Characteristics of

Three Cyclic Electric, External De-Icing Boots Employing

Chordwise Shedding. NACA RM E53C26, 1953.

9. Gray, V.H., and Bowden, D.T.: Comparison of Several Methods

of Cyclic De-Icing of a Gas-Heated Airfoil. NACA RM E53C27,

1953.

10. Neel, C.B., Jr.: The Design of Air-Heated Thermal Ice­

Prevention Systems. (Presented at the Airplane Icing Information Course at the University of Michigan, March 30 - April 3, 1953).

11. Bowden, D.T.: Investigation of Porous Gas-Heated Leading­

Edge Section for Icing Protection of a Delta Wing. NACA RM E54I03, 1955.

12. Gray, V.H., and von Glahn, U.H.: Heat Requirements for Ice

Protection of a Cyclically Gas-Heated, 36 Degree Swept

Airfoil with Partial-Span Leading-Edge Slat. NACA RM E56B23, 1956.

13. Gowan, W.H. and Mulholland, D.R.: Effectiveness of Thermal­

Pneumatic Airfoil-Ice-Protection System. NACA RM E50K10a, 1951.

Performance Penalties

1. von Glahn, U.H., and Gray, V.H.: Effect of Ice Formations

on Section Drag of Swept NACA 63A-009 Airfoil with Partial­

Span Leading-Edge Slat for Various Modes of Thermal Ice Protection. NACA RM E53J30, 1954.

2. Gray, V.H., and von Glahn, U.H.: Effect of Ice and Frost

Formations on Drag of NACA 65(sub 1)-212 Airfoil for Various

Modes of Thermal Ice Protection. NACA TN 2962, 1953.

3. Preston, G.M., and Blackman, C.C.: Effects of Ice

Formations on Airplane Performance in Level Cruising Flight.

NACA TN 1598, 1948.

4. Gelder, T.F., Lewis, J.P., and Koutz, S.L.: Icing

Protection for a Turbojet Transport Airplane: Heating Requirements, Methods of Protection, and Performance Penalties. NACA TN 2866, 1953.

5. Bowden, D.T.: Effect of Pneumatic De-Icers and Ice

Formations on Aerodynamic Characteristics of an Airfoil.

NACA TN 3564, 1956.

6. Gray, V.H.: Correlations Among Ice Measurements,

Impingement Rates, Icing Conditions and Drag of a 65A004 Airfoil. NACA TN 4151, 1958.

7. Gray, V.H. and von Glahn, U.H.: Aerodynamic Effects Caused by Icing of an Unswept NACA 65A-004 Airfoil. NACA TN 4155,

1958.

8. Gray, V.H.: Prediction of Aerodynamic Penalties Caused by

Ice Formations on Various Airfoils. NASA TN D-2166, 1964.

Windshield Icing Protection

1. Holdaway, G.H., Steinmetz, C.P., and Jones, A.R.: A Method

for Calculating the Heat Required for Windshield Thermal Ice Prevention Based on Extensive Flight Test in Natural Icing Conditions. NACA TN 1434, 1947.

2. Ruggeri, R.S.: Preliminary Data on Rain Deflection from

Aircraft Windshields by Means of High-Velocity Jet-Air

Blast. NACA RM E55E17a, 1947.

Cooling Fan Icing Protection

1. Lewis, J.P.: Wind-Tunnel Investigation of Icing of an

Engine Cooling-Fan Installation. NACA TN 1246, 1947.

Radome Icing Protection

1. Lewis, J.P.: An Analytical Study of Heat Requirements for Icing Protection of Radomes. NACA RM E53A22, 1953.

2. Lewis, J.P., and Blade, R.J.: Experimental Investigation of

Radome Icing and Icing Protection. NACA RM E52J31, 1953.

Inlet and Vent Icing Protection

1. Ruggeri, R.S., von Glahn, U., and Rollin, V.G.:

Investigation of Aerodynamic and Icing Characteristics of Recessed Fuel-Vent Configurations. NACA TN 1789, 1949.

Jet Penetration

1. Callaghan, E.E., and Ruggeri, R.S.: Investigation of the

Penetration of an Air Jet Directed Perpendicularly to an

Airstream. NACA TN 1615, 1948.

2. Ruggeri, R.S., Callaghan, E.E., and Bowden, D.T.:

Penetration of Air Jets Issuing from Circular, Square, and Elliptical Orifices Directed Perpendicularly to an

Airstream. NACA TN 2019, 1950.

3. Callaghan, E.E., and Bowden, D.T.: Investigation of Flow

Coefficients of Circular, Square, and Elliptical Orifices at High Pressure Ratios. NACA TN 1947, 1949.

4. Ruggeri, R.S.: General Correlation of Temperature Profiles

Downstream of a Heated Air Jet Directed at Various Angles to

Airstream. NACA TN 2855, 1952.

5. Callaghan, E.E., and Ruggeri, R.S.: A General Correlation

of Temperature Profiles Downstream of a Heated Air Jet Directed Perpendicularly to an Airstream. NACA TN 2466,

1951.

Heat Transfer

1. Gray, V.H.: Improvements in Heat Transfer for Anti-Icing of

Gas-Heated Airfoils with Internal Fins and Partitions. NACA TN 2126, 1950.

2. Gray, V.H.: Simple Graphical Solution of Heat Transfer and

Evaporation from Surface Heated to Prevent Icing. NACA TN 2799, 1952.

3. Callaghan, E.E.: Analogy between Mass and Heat Transfer

with Turbulent Flow. NACA TN 3045, 1953.

4. Coles, W.D., and Ruggeri, R.S.: Experimental Investigation

of Sublimation of Ice at Subsonic and Supersonic Speeds and

its Relation to Heat Transfer. NACA TN 3104, 1954.

5. Coles, W.D.: Experimental Determination of Thermal

Conductivity of Low-Density Ice. NACA TN 3143, 1954.

6. Coles, W.D.: Icing Limit and Wet-Surface Temperature

Variation for Two Airfoil Shapes under Simulated High-Speed

Flight Conditions. NACA TN 3396, 1955.

7. von Glahn, U.: Preliminary Results of Heat Transfer from a

Stationary and Rotating Ellipsoidal Spinner. NACA RM E53F02, 1953.

Miscellaneous

1. Gray, V.H.: Correlation of Airfoil Ice Formations and Their

Aerodynamic Effects with Impingement and Flight Conditions. (Presented at the SAE National Aeronautics Meeting - Sept. 30 - Oct. 5, 1957), SAE Preprint No. 225.

2. von Glahn, U.H.: The Icing Problem: Current Status of NACA

Techniques and Research. (Paper presented at Ottawa AGARD Conference), June 10-17, 1955. AG 19/P9.

3. von Glahn, U.H.: Some Considerations of the Need for Icing

Protection of High-Speed, High-Altitude Airplanes. NACA Conference on Some Problems of Aircraft Operation, November

17-18, 1954.

4. Lewis, W. and Perkins, P.J.: A Flight Evaluation and

Analysis of the Effect of Icing Conditions on the PG-2 Airship. NACA TN 4220, 1958.

5. Lewis, W.: Icing Conditions to be Expected in the Operation

of High-Speed, High-Altitude Airplanes. NACA Conference on Some Problems of Aircraft Operation, November 17-18, 1954.

6. NACA Conference on Aircraft Ice Prevention. A compilation

of the Papers Presented by NACA Staff Members. June 26-27,

1947.

7. Gray, V.H.: Heat Requirements for Ice Prevention on

Gas-Heated Propellers. (Presented at SAE Annual Meeting, January 9-13, 1950), SAE Preprint No. 424.

8. Bowden, D.T., Gensemer, A.E., and Speen, C.A: Engineering

Summary of Airframe Icing Technical Data. Federal Aviation

2 1 Apr 71 AC 20- 73

CHAPTER 4. TESTS

CHAPTER 4. TESTS

SECTION 1. GENERAL

24. GENERAL.

a. The considerations of meteorological and operational factors were discussed in Chapters 2 and 3 to indicate h.Jw the performance of an icing system can he predicted from an analysis of a combination of these factors. Chapter 4 outlines procedures for testing ice protection systems in terms of these factors.

SECTION 1. GENERAL

h. Assuming that a system has been designed in accordance with the

foregoing design approach that the design points can be justified as being the most severe, testing at the design points is all that would be required to show compliance with the regulations. Tests should be adequate to verify the manufacturer's analysis and selection of critical design points.

SECTION 2. TEST METHODS

SECTION 2. TEST METHODS

25. NATURAL ICING FLIGHT TESTS.

a. One of the best methods for determining the performance of any aircraft ice protection system is to subject the aircraft and the protection system to natural icing conditions and to demonstrate

that the airplane can be safely operated while exposed to the icing conditions defined by Figure 1 and Figure 4 of Appendix C to FAR 25. Natural icing tests are required prior to certification

for operation in ~cing conditions.

h. For flights in search of icing conditions, it is preferable to

select the geographical area and seasonal period and to watch the weather map for the desired wind direction, velocity, cloud condition, and temperature. Efforts should be made to find an area where air traffic will permit step climbs through stratoform clouds to seek out the high LWC level of the cloud.

c. Ice formation resembling those produced in icing tunnels (within

the area of the envelope bounded by LWC of 0.3 to 0.55, with drop size of approximately 20 microns, and in a temperature range of 26° F. to 30° F.) has been observed on many occasions within a very narrow altitude range (200 to 500 feet). This sometimes occurs just below a temperature inversion altitude where there is a mild underrunning of cold air (lifting warm air).

Chap 4 Par 24 Page 19

AC 20- 7 3 2 I Apr 71

d. The flight test aircraft should hnvl' instrumentation to dl•tt•nni•w

liquid water content and droplet siz<.• or a means of determining ice accretion rate and the extent of impingement from which these parameters can be established. Rotating cylinders, calibrated in an icing tunnel, have been employed but with mixed success because of boundary layer variations and difficulty with storage. A calibrated liquid water content indicator can be used to

determine liquid water content. Drop size can be approximated from the extent of impingement on any shape with known impingement characteristics or by other acceptable means. Oil slides have been used With some success with carefully controlled procedures and correlation when feasible with other techniques.

e. State-of-the-art airborne icing measurement instrumentation,

however, has shortcomings. A simple but imprecise indicator of the liquid water content and drop size values of Figure 1 in Appendix C is the observation and photographing of ice buildup

on an unprotected surface and correlation (corrected for velocity) with similar buildup under measured conditions in an icing tunnel. When the conditions of Figure 1 have been obtained, the airplane

should be investigated for handling qualities to explore the effect of ice accretion on the unprotected surfaces.

f. For an airplane of new design (planform) and for aft-mounted engines, where ice shedding from the wing leading edge can cause

engin~ damage or flameout, the aircraft flight test program should require determination of the effects of ice shedding.

g. Finding cumuliform icing conditions of Figure 4 severity involves

seasonal, geographical, and time of day considerations. Experience indicates that the most representative e.nd readable condition will occur:

(1) In a mild cold front system with 11building 11 cells.

(2) Over generally flat terrain.

(3) With warmer moist air reaching the freezing level between

8,000 to 12,000 feet.

(4) Flyir~ parallel to the front through a series of altitudes.

This type of frontal system usually provides an escape route to

the sunny side for qualitative evaluation and photography of ice shapes and dimensions.

Chap 4 Par 25

21 Apr 71 AC 20-73

21 Apr 71 AC 20-73

(h) Conditions to be avoided because of hazard or lack of useful data

are:

(1) Late afternoon highly active line squalls.

(2) Snow and hail.

(3) Central U.S.A. in "tornado alley."

(4) Contour holes on airborne radar.

(i) The value of natural icing flight tests can vary with the

following:

(1) Correlation of test results with analysis predictions.

(2) Ability to compare with previous designs.

(3) Extent of icing tunnel tests as basic criteria.

(4) Extent of successful correlation of flight skin temperature

surveys in dry and wet air full-scale tests with similar shapes and temperatures investigated in the icing tunnel.

(5) Correlation of natural icing test buildup on representative or known sections with icing tunnel shapes, considering correction for time and airspeed.

(6) The absence of unprotected ice-catching protuberances, such as antennas, scoops, struts, etc.

26. DRY AIR FLIGHT TESTS. Dry air flight tests can be used to verify many of the design objectives of an icing system. These tests may be conducted as a preliminary to natural icing tests to check the function and performance of all system components and compatibility of systems. Calculated engine bleed air mass flows for developing thrust setting curves can be verified, and models of predicted ice shapes can be installed on unprotected surfaces and evaluated in terms of lift, drag, and controllability factors of the airplane. An analysis of heat requirements and availability at various operational conditions can be performed from data collected during dry air tests.

27. FLYING TANKER TESTS. Flying tanker tests have been used chiefly by the military to verify satisfactory operation of icing systems in simulated icing conditions. Equipping an airplane for this type of test can be very expensive for a manufacturer in terms of the actual time such equipment would be used in a certification program, and the limitations of such equipment in simulating an actual icing encounter.

Chap 4

Par 25 Page 21

AC 20-73 21 Apr 71

Turbulence, inability to expose the complctt· airplane to icing conditions at a given time, and problems in cnlilnating the LWC and droplet size of the tanker spray are some of the difficulties encountered with tanker tests. Droplet size has not been easily controlled by spray rigs, nor has liquid water content been easily determined. LWC produce4 by the spray rig is a function of the distance between the test airplane and the rig since the water disperses very quickly. For these reasons, such tests are not generally considered adequate for showing full compliance with the regulations.

28. SELF-CONTAINED SPRAY RIG TESTS.

a. Certain areas or test sections of airplane icing systems can be

tested by installing spray rigs on the airplane in such a manner as to cause impingement on the surfaces during flight. Some of the litnitations applicable to tanker tests also apply to spray rig tests. Test rigs of this nature are expensive to develop and install on test aircraft.

b. An additional advantage of this type of testing is the ability

to control the distance between the spray section and the test section. The downstream meteorological environment produced by an artificial spray cloud is a function, among other things, of the distance between the test section and the spray rig producing the cloud.

c. The major disadvantage of this method is the possible disruption

to the flow field around the test surface due to the presence of the rig itself. This feature may produce unrealistic impingement characteristics which are difficult to evaluate. The size and weight restrictions of the spray rig structure also

limit the area that can be subjected to the spray. Because of the limitations of this test method, it is not generally considered adequate for showing full compliance with the regulations; however, this does not eliminate its use as a development tool or for testing relatively small areas for icing.

29. ICING TUNNEL TESTS. Icing tunnel tests are perhaps the least expensive and most accurate method for determining the performance of an icing system under various conditions. There are several icing tunnels in existence which have the capability to control LWC, droplet size, and temperature conditions quite accurately

over their range of capabilities. The advantages of ice tunnel test facilities are their ability to control the meteorological conditions through a range of values, to simulate a variety of operational conditions, and to measure performance quite accurately. Instrumentation is generally more extensive and accurate than flight test instrumentation. The disadvantages of

Chap 4 Par 27

21 Apr 71 AC 20- lJ

21 Apr 71 AC 20- lJ

ice tunnel tests are their inability to simulate altitude effects or the effects of ice accumulations on unp1otected surfaces, and their inability to provide the combined operational and meteorological conditions that exist during an icing encounter of the full-scale airplane. Turbulence, sidewall effects, size, and scaling factors can be problems in ice tunnel tests. Most tunnels are very small and obtaining aerodynamic and thermodynamic similarity for models of large components can be difficult. A dimensional analysis of the aerodynamic and thermodynamic parameters which describe the full-scale system should be undertaken prior to model tests to assure similarity between the full-scale and model-scale systems. Full-scale values may be determined from natural icing flight tests, dry air flight tests, spray rig tests, tanker tests, or any combination of these tests.

30. COMBINATION OF METHODS. Flight tests in natural icing conditions under design point meteorological and operational conditions provide the most desirable method for showing compliance with the regulations. For substantiation, however, a combination of methods may be necessary. The most desirable combination of methods would usually comprise icing

tunnel tests at the design points, with dry air and natural icing tests of the full-scale system under actual flying conditions. Data obtained by the flight tests can be used to verify the manufacturer's analy~is and ice tunnel data. The flight tests should also assure that no severe operational or design deficiency exists.

31. ICE SHEDDING.

a. The path of ice releas.ed from the aircraft is affected by many variables, such as ice shape and density, aircraft attitude and

altitude, airspeed, air flow, manner in which the ice is released, etc. Therefore, it may be difficult on some configurations to show that ice released will not enter into engine inlet ducts or strike and damage other parts of the aircraft. A desirable approach for resolving an apparent "ice shedding" problem is to install anti-icing provisions in critical areas. The same procedures used to substantiate other aircraft anti-icing syste~s are applicable.

b. If anti-icing provisions are not installed in critical ice shedding areas, then investigations should be conducted to show that ice which sheds off of the aircraft will not cause an unsafe condition.

"Ice shedding" investigations should be made during and after ice encounters. Sufficient encounters in all intended operation conditions should be made to assure there is no hazard associated with the release of ice. In addition to the usual measurements and

Chap 4 Par 29 Page 23

AC 20-73 21 Apr 71

observations made during ice encounter tests, the following additional instrumentation and/or observations arc suggested:

(1) Motion pictures to record the trajectory of ice released

from the aircraft.

(2) Photopanel for turbine-engine-powered aircraft to record EGT, EPR, and RPM for the purpose of detecting adverse effects on engine operation.

(3) Visual examination of the aircraft for damage before and

after ice encounters, especially in the area of the engine compressor and inlet.

SECTION 3. TEST PROCEDURES

SECTION 3. TEST PROCEDURES

32. AIRFRAME SURFACES (WINGS, EMPENNAGE, CONTROL SURFACES, ENGINE INLETS, WlNDSiuELDS. AND INSTRUMENTS, ETC. ) SYSTEMS.

a. Ice Tunnel Tests.

(1) For ice tunnel tests of these areas, design point values of LWC, Dd, and T should be established in the tunnel at the

pressure, temperature, velocity, etc., defined by the design operational conditions. Models should be designed to assure that Reynolds m.unbers and other dimensionless parameters are maintained as closely as possible to the full-scale value. They should be mounted to simulate the flight attitude associated with the most severe conditions. If ·flaps or other devices are used to produce. the proper flow field conditions, instrumentation should be provided to show that

test and design values are in general agreement. In an ice tunnel test of an evaporative system, all of the impinging water should evaporate. In an ice tunnel test of a non-evaporative or running wet system, the predicted amount of runback water should not be exceeded and any ice

Continue reading ↓ 120 of 165 passages shown