AC 150/5345-39D Specification for L-853, Runway and Taxiway Retroreflective Markers
Contains the Federal Aviation Administration (FAA) standards for retroreflective markers for airport runways and taxiways. Version D changes Paragraph 3.4.2.2, Cylindrical Markers, to increase the marker diameter and surface area, and Paragraph 3.4.3.1, Mounting System, to clarify Type II marker mounting and tethering requirements. Effective six months after the issue date of this AC, only equipment qualified per these specifications will be listed in AC 150/5345-53, Airport Lighting Equipment Certification Program.
This document is no longer current. Cancelled by 150/5345-39E. Check the official source before relying on it.
Advisory Circular
U.S. Department of Transportation Federal Aviation Administration
Subject: SPECIFICATION FOR L-853,
RUNWAY AND TAXIWAY RETROREFLECTIVE MARKERS
Date: 09/26/11 Initiated by: AAS-100
AC No.: 150/5345-39D Change:
1. PURPOSE. This Advisory Circular (AC) contains the Federal Aviation Administration (FAA) standards for retroreflective markers for airport runways and taxiways.
2. EFFECTIVE DATE. Effective six months after the issue date of this AC, only equipment qualified per the specifications herein will be listed per AC 150/5345-53, Airport Lighting Equipment Certification Program.
3. CANCELLATION. AC 150/5345-39C, FAA Specification L-853, Runway and Taxiway Retroreflective Markers, dated September 14, 2006 is cancelled.
4. APPLICATION. The Federal Aviation Administration (FAA) recommends the guidance and specifications in this Advisory Circular for retroreflective markers. In general, use of this AC is not mandatory. However, use of this AC is mandatory for all projects funded with federal grant monies through the Airport Improvement Program (AIP) and with revenue from the Passenger Facility Charges (PFC) Program. See Grant Assurance No. 34, “Policies, Standards, and Specifications,” and PFC Assurance No. 9, “Standards and Specifications.” All retroreflective marker designs contained in this standard are the only means acceptable to the Administrator to meet the lighting requirements of Title 14 CFR Part 139, Certification of Airports, Section 139.311, Marking, Signs and Lighting.
5. PRINCIPAL CHANGES.
a. Paragraph 3.4.2.2b is added to clarify the Type II retroreflective marker maximum cylinder
diameter.
b. Paragraph 3.4.2.2c is added to clarify the standard height requirement of a Type II retroreflective
marker.
c. Paragraph 3.4.3.1 is reworded to clarify Type II marker mounting system requirements.
6. METRIC UNITS. To promote an orderly transition to metric units, this AC contains both English and metric dimensions. The metric conversions may not be exact metric equivalents and, until there is an official changeover to the metric system, the English dimensions will govern.
7. COMMENTS OR SUGGESTIONS for improvements to this AC should be sent to:
Manager, Airport Engineering Division Federal Aviation Administration ATTN: AAS-100 800 Independence Avenue, S.W. Washington DC 20591
8. COPIES OF THIS AC. The Office of Airport Safety and Standards is in the process of making ACs available to the public through the Internet. These ACs may be found through the Federal Aviation Administration (FAA) home page (www.faa.gov). Michael J. O’Donnell Director of Airport Safety and Standards
1.1.2 Classification. › 1.2.2 Styles.
SECTION 1. SCOPE AND CLASSIFICATION.
1.1.1 Scope.
This specification covers the requirements for retroreflective markers for airport runways and taxiways.
1.1.2 Classification.
Two types and two styles of retroreflective markers are covered by this specification.
1.2.1 Types.
a. Type I, Semiflush Marker for Centerline Marking
b. Type II, Elevated Marker for Edge Marking.
1.2.2 Styles.
The style designation applies to Type I markers only:
a. Style I, Plowable Markers.
b. Style II, Non-plowable Markers
2.1 General. › 2.1.3 American Society for Testing and Materials (ASTM) Standard.
SECTION 2. REFERENCED DOCUMENTS.
2.1 General.
The following is a listing of documents referenced in this AC:
2.1.1 Federal Aviation Administration (FAA) Publications.
2.1.1.1 FAA Advisory Circulars (ACs).
AC 150/5345-53 Airport Lighting Equipment Certification Program
AC 150/5340-30 Design and Installation Details for Airport Visual Aids
2.1.2 Military and Federal Publications.
2.1.2.1 Military Standard.
MIL-STD-810F Environmental Engineering Considerations and Laboratory Tests 1 January 2000
2.1.2.2 Federal Specifications and Standards.
L-P-380 Plastic Molding Material Methacrylate
2.1.3 American Society for Testing and Materials (ASTM) Standard.
ASTM D 4280-08 Standard Specification for Extended Life Type, Nonplowable, Raised Retroreflective Pavement Markers
ASTM D 4383-05 Standard Specification for Plowable, Raised Retroreflective Pavement Markers.
ASTM D 4956-09 Standard Specification for Retroreflective Sheeting for Traffic Control
2.1 General. › 2.1.4 Document Sources.
2.1.4 Document Sources.
FAA ACs may be obtained from:
Website: http://www.faa.gov/airports/resources/advisory_circulars/ Military standards and specifications publications may be obtained from:
DAPS/DODSSP Building 4, Section D 700 Robbins Avenue Philadelphia, PA 19111-5094 Telephone: (215) 697-2179 FAX: (215) 697-1460 Website: https://assist.daps.dla.mil/online/start/ NOTE: User must establish and be approved for a personal account to download documents. See ASSIST website instructions.
Federal specifications and standards may be obtained from:
Federal Supply Services Specification Section 470 L'Enfant Plaza East SW Suite 8100 Washington, DC 20407
Telephone: (202) 619-8925 FAX: (202) 619-8985 Website: https://assist.daps.dla.mil/online/start/ NOTE: User must establish and be approved for a personal account to download documents. See ASSIST website instructions.
ASTM standards may be obtained from:
ASTM International 100 Barr Harbor Drive P.O. Box C700 West Conshohocken, PA 19428-2959
Telephone: (610) 832-9585 FAX: (610) 832-9555 Website: http:/www.astm.org
3.1.1.2 Configuration. › 3.1.1.2.2 Type II Lens Retroreflectors.
SECTION 3. REQUIREMENTS.
3.1 Retroreflective Material Requirements.
3.1.1 General.
3.1.1.1 Construction.
Retroreflective material is designed to reflect light at an oblique angle back toward its source. Two types of retroreflective material are in wide use:
a. Sealed plastic lenses with a smooth face and a prismatic configuration on the back (referred
to herein as lens retroreflectors).
b. Flexible sheeting with a smooth face, embedded optical retroreflective elements, and an
adhesive backing (referred to herein as sheet retroreflectors).
3.1.1.2 Configuration. The configuration of the retroreflective material on a marker should be designed to maximize its visibility. When the viewer is facing the marker, it must be visible as a single color with a continuous unbroken surface. Separated color strips (bands) of the same color or differing colors laid out across the marker face must not be used. In the case of a bidirectional marker, only a single color per side must be visible.
3.1.1.2.1 Type I Lens Retroreflectors.
Type I, Semiflush Marker for Centerline Marking, is to be used as centerline marker only. The configuration of the Type I marker will be as follows:
a. Runway centerline markers will be white in color.
b. Taxiway centerline markers will be green in color.
3.1.1.2.2 Type II Lens Retroreflectors. The configuration of the Type II marker will be as follows:
a. Runway edge markers will be solid white in color.
b. Taxiway edge markers will be solid blue in color.
c. Runway threshold markers will be green in color.
d. Runway end markers will be red in color.
e. Runway threshold markers and runway end markers may be combined in one bidirectional
marker.
3.1.3 Lens Retroreflector Requirements. › 3.1.3.1 Specific Intensity (SI).
3.1.1.2.3 Type II Sheet Retroreflectors.
a. Runway edge markers will be solid white in color.
b. Taxiway edge markers will be solid blue in color.
c. Runway threshold markers will be green in color.
d. Runway end markers will be red in color.
e. Runway threshold markers and runway end markers may be combined in one bidirectional
marker.
3.1.2 Sheet Retroreflector Requirements.
a. The sheet retroreflector material must be manufactured and perform per the requirements of
ASTM D 4956-09, Standard Specification for Retroreflective Sheeting for Traffic Control. The manufacturer may use Class 1 through 4 adhesive backings.
b. The sheet retroreflector material used must be Type III Sheeting or higher per ASTM D
4956-09. See ASTM D 4956-09, Table 4, Type III Sheeting, for the minimum reflection coefficients (RA) for colors white, green, red, and blue.
3.1.3 Lens Retroreflector Requirements.
3.1.3.1 Specific Intensity (SI).
a. Lens retroreflectors used in Type I markers must have the minimum SI per Table 1.
b. Lens retroreflectors used in Type II markers must have the minimum specific intensities (SI)
per Table 2.
c. The values listed in both tables are for a clear (white) lens retroreflector. Red and green lens
retroreflectors must be at least 25 percent of this value and blue must be at least 8 percent of this value.
Table 1. Minimum SI for clear (white) Type I markers.
Observation angle (degrees) Entrance angle (degrees) Specific intensity (candelas
per foot-candle) 0.2 0 3.0 0.2 20 Right 1.2 0.2 20 Left 1.2
SECTION 3. REQUIREMENTS. › 3.2 Environmental Requirements.
Table 2. Minimum SI per unit area for clear (white) Type II lens retroreflectors.
Observation angle (degrees) Entrance angle (degrees) Specified brightness (candelas per foot-candle per
square inch) 0.1 0 14.0 0.1 20 5.6 0.167 0 10.0 0.167 20 4.0 0.33 0 7.0 0.33 20 2.8
3.1.3.2 Chromaticity.
a. For Type I lens retroreflector markers, the approved colors are per paragraph 3.1.1.2.1. Style
I markers must meet the color boundaries only (no other parts of the standard are applicable) per ASTM D4383-05, Standard Specification for Plowable, Raised Retroreflective Pavement Markers, paragraph 6.2, Color. Style II markers must meet the color boundaries only (no other parts of the standard are applicable) per ASTM D4280-08, Standard Specification for Extended Life Type, Nonplowable, Raised Retroreflective Pavement Markers, paragraph 6.2.4, Color.
b. The colors approved for use on Type II lens retroreflector markers are per paragraph 3.1.1.2.2
and must meet the color boundaries only (no other parts of the standard are applicable) per ASTM D4280-08, paragraph 6.2.4, Color.
c. The markers may be unidirectional, bi-directional with the same color, or bi-directional with
two different colors. The particular color depends on the intended use.
3.1.3.3 Fabrication.
a. The lens retroreflector must be one of the colors specified in paragraphs 3.1.1.2.1 and
3.1.1.2.2.
b. The lens retroreflectors must consist of a transparent plastic face (the lens) and an opaque
back fused to the lens (under heat and pressure) around the entire perimeter to form a homogeneous unit permanently sealed against dust, water, and water vapor.
c. The lens retroreflector must consist of a smooth front surface free from projections or
indentations other than for identification and a rear surface bearing a prismatic configuration so that it will effect total internal reflection of light.
d. The manufacturer's trademark must be molded legibly into the face of the lens.
e. The lens retroreflector shell material must conform to Federal Specification L-P-380, Plastic
Molding Material Methacrylate, Type I, Class 3.
3.2 Environmental Requirements.
All retroreflector markers must withstand the following environmental conditions:
3.2.1 Temperature.
Exposure to any temperature from -67° F to +149° F (-55° C to +65° C).
3.2.2 Wind.
Exposure to wind speeds up to 100 mph (161 kilometers per hour (km/h)) from any direction.
3.2.3 Salt Fog.
3.3 Type I Marker. › 3.3.2 Dimensions.
Exposure to a salt-laden atmosphere.
3.2.4 Sunshine.
Exposure to solar radiation.
3.2.5 Weather.
Exposure to all normal operating environmental conditions.
3.2.6 Humidity.
Exposure to any relative humidity between 10 and 95 percent.
3.3 Type I Marker.
3.3.1 Design.
a. Style I markers must withstand the impact of a snowplow blade without damage or must be
configured so that the blade passes over the marker.
b. The base must have adequate area to dissipate the loading specified in paragraph 4.2.8 and
provide for secure bonding to the pavement.
c. The marker may be unidirectional or bi-directional, depending on the user's requirements.
d. The design of the marker must minimize scratching and abrasion of the retroreflective
material.
3.3.2 Dimensions.
a. The Type I marker must not project more than 3/4 inch (20 mm) above the pavement surface.
b. All corners and edges of the marker projecting above the pavement must be rounded to a
minimum radius of 1/8 inch (3 mm).
c. The minimum retroreflective area in each viewing direction must be 1.5 in2 (9.7 cm2) for
Style I markers and 3 in2 (19.3 cm2) for Style II markers.
3.3.3 Bonding.
a. Type I, Style I and II markers bonded to the pavement surface must have a clean, flat, hard,
rough-textured surface that will promote bonding.
b. The bonding material must be specified or supplied by the manufacturer and must meet the
3.4.2 Dimensions. › 3.4.2.2 Cylindrical Markers.
requirements of paragraph 4.2.6.
3.4 Type II Marker.
3.4.1 Design.
a. There are three configurations of Type II markers:
(1) Plane (flat) surface with lens retroreflectors attached;
(2) Plane (flat) surface with sheet retroreflectors attached; or
(3) Cylindrical surface with sheet retroreflectors attached.
b. The marker must be as compact as practical while presenting the required retroreflective area.
c. The retroreflective material must be at least 2 inches (5.1cm) above the ground when
mounted or 3 inches (7.6 cm) if a frangible coupling is used.
3.4.2 Dimensions.
3.4.2.1 Plane Markers.
a. For a plane surface Type II marker with lens retroreflectors, the retroreflector surface area
must be at least 6.5 in2 (41.9 cm2).
b. For a plane surface Type II marker with sheet retroreflector material, the retroreflector
surface area must be at least 24 in2 (155 cm2).
c. If the plane markers are bidirectional, the surface areas in paragraphs 3.4.2.1a and b represent
the required retroreflector surface area facing each direction.
3.4.2.2 Cylindrical Markers.
a. For a cylindrical surface marker, at least 96 in2 (619 cm2) of sheet retroreflector material must
be wrapped uniformly about the cylinder. The sheeting must extend up to the top of the cylinder.
b. The maximum cylinder diameter must not exceed 8 inches (20.3 centimeters).
c. The standard installed height of the reflector must be 14 inches (35.6 centimeters) above
finish grade. See the installation requirements for the height of the edge reflector versus distance from the defined pavement edge in AC 150/5340-30.
3.4.3 Construction. › 3.4.3.3 Materials.
3.4.3 Construction.
3.4.3.1 Mounting System.
a. The manufacturer must provide a mounting system that is appropriate for the type of surface
(asphalt, grass, concrete).
b. The mounting system must withstand the required wind loading per paragraph 3.2.2.
c. The mounting system must be designed to prevent the marker or its components from being
ingested by jet aircraft.
3.4.3.2 Type II Marker Frangibility and Tethering.
a. The Type II marker must be designed to be either flexible or mounted with a frangible fitting
(with a breaking point no more than 3 inches above grade) so that it will minimize damage to an aircraft if it strikes the marker.
b. To utilize a non-frangible mounting, the Type II marker must readily bend or flex when
struck so as to minimize damage to an aircraft or vehicle.
c. Each Type II marker and mounting system must withstand a wind speed of 100 mph (161
km/h) without permanent deformation and must retain its original shape and position in winds up to 50 mph (80 km/h).
d. A tether anchor hard point is required for Type II markers that are designed to break rather
than bend or flex. The tether must be a weather and corrosion resisting material capable of securing the retroreflector when separated from its base or mounting stake and prevent a Foreign Object Debris (FOD) hazard.
3.4.3.3 Materials.
a. Any metal used in the Type II marker or associated mounting hardware must be corrosion
resisting, plated, or treated to resist corrosion.
b. The Type II plane-type (flat) markers and mounting hardware must be constructed so that the
plane orientation will not change when the marker is subjected to the specified wind conditions.
c. The sheet retroreflector material for all Type II markers must be securely fastened to the
marker body so that it will not slip or loosen when exposed to the specified environmental conditions.
4.2 Qualification Tests. › 4.2.2 High Temperature Test.
SECTION 4. EQUIPMENT QUALIFICATION REQUIREMENTS.
4.1 Qualification Procedures.
Procedures for qualifying equipment to be furnished under the Federal grant assistance program for airports are in AC 150/5345-53, Airport Lighting Equipment Certification Program.
4.2 Qualification Tests.
The following tests must be performed on each unit submitted for qualification, to demonstrate compliance with the specifications:
4.2.1 Retroreflector Material.
a. This section specifies tests for the retroreflector material component of the marker.
b. For Type II markers using sheet retroreflector material, the manufacturer must submit the
material to the third party certification body for testing. In lieu of testing, the manufacturer may provide a certificate of compliance (issued by the material supplier) to the third party certification body attesting that the material meets the standards in ASTM 4956-09.
c. All Type I or Type II markers using lens retroreflectors must be tested by the third party
certification body.
4.2.1.1 Sheet Retroreflector Material.
The sheet retroreflector material must pass the tests listed for Type III or higher sheeting in ASTM Standard D4956-09, Standard Specification for Retroreflective Sheeting for Traffic Control, Paragraph 7, Test Methods.
4.2.1.2 Lens Retroreflectors.
a. Type I, Style I lens retroreflectors must meet the requirements for specific intensity and
chromaticity in paragraph 3.1.3. See ASTM D4383-05, Standard Specification for Plowable Raised Retroreflective Pavement Markers, Paragraph 10, Test Methods, for test procedures.
b. Type I, Style II lens retroreflectors must meet the requirements for specific intensity and
chromaticity in paragraph 3.1.3. See ASTM D4280-08, Standard Specification for Extended Life Type, Nonplowable Raised Retroreflective Pavement Markers, paragraph 9, Test Methods, for test procedures.
4.2.2 High Temperature Test.
a. Nonmetallic markers must be subjected to a temperature of +149° F ±3.6° (+65° C ±2.0°) for
a period of not less than 7 hours.
b. Any evidence of heat damage, such as deformation, blistering, cracking or crazing of plastic
material, or deterioration of filler material, will be cause for rejection.
4.2.3 Low Temperature Test.
a. Nonmetallic Type I and II markers must be subjected to a temperature of -67° F ± 3.6 (-55°
C ±2.0°) for a period of 24 hours.
b. Evidence of damage will be cause for rejection.
4.2 Qualification Tests. › 4.2.8 Type I Marker Load Test.
4.2.4 Salt Fog Test.
a. Markers with no ferrous metal are exempt from this test. The sample marker (with all
accessory hardware) must be subjected to a salt fog test per MIL-STD-810F, Method 509.4, Salt Fog, paragraph 4.5.2, Procedure.
b. The test duration must be 48 hours exposure and 48 hours drying.
c. Analyze any corrosion for its immediate and potential long-term effects on the proper
functioning and structural integrity of the test item.
4.2.5 Sunshine Test.
a. A sunshine test must be conducted per MIL-STD-810F, Method 505.4, Solar Radiation,
paragraph 4.4.3, Procedure II for all Type I and II markers with nonmetallic exterior parts.
b. The markers must be subjected to a minimum of 56 cycles. Any evidence of deterioration
will be cause for rejection.
4.2.6 Type I Marker Bond Test.
a. A 2 1/4-in. ±1/4 in. (5.7 cm ± 0.6 cm) diameter steel fitting must be bonded to the bottom
surface of the Type I marker with an adhesive material specified for use with the marker.
b. After the adhesive material cures, the steel fitting must be pulled away from the marker at a
force not greater than 2,500 pounds (1133.9 kg).
c. The adhesive material and bottom surface of the marker is considered unsatisfactory if there
is complete separation with a pull of less than 1,500 pounds (680.3 kg).
4.2.7 Type I Seal Test.
a. To demonstrate the integrity of the watertight gasket seal, Type I markers must be subjected
to the immersion test described in MIL-STD-810F, Method 512.4, Immersion, paragraph 4.4.2, Procedure I.
b. Any evidence of water or condensation in the marker housing is considered unsatisfactory
performance.
4.2.8 Type I Marker Load Test.
a. This test must be the last test performed.
b. The Type I marker must be bonded to a flat steel plate mounted in a standard testing machine.
4.2 Qualification Tests. › 4.2.9 Type II Marker Wind Load Test.
c. The load must be applied to the top part of the marker through a block of rubber, 4 inches (10
cm) in diameter, 1 inch (2.5 cm) thick with Shore A hardness of 55 to 70.
d. A total of 10,000 pounds (4,536 kg) must be applied uniformly over the area of the rubber at
a rate of not greater than 2,500 pounds (1,134 kg) per minute.
e. The results will be considered unsatisfactory if there is any permanent deformation, cracking,
or breaking of any materials used.
4.2.9 Type II Marker Wind Load Test.
a. The Type II marker and its mounting system must be subjected to wind load tests.
b. Apply a wind load of 50 mph (80 km/h) for 10 minutes to a flexible marker to demonstrate
that the marker remains upright at this wind speed.
c. Apply a wind load of 100 mph (161 km/h) for 10 minutes to all Type II markers; the markers
and mounting system must not show any signs of permanent distortion or failure.
d. An equivalent static force calculated from the wind velocities in paragraphs 4.2.9b and c may
be used to demonstrate the wind loading requirement. The equivalent force must be applied perpendicular to the vertical axis of the Type II marker.
SECTION 5. PRODUCTION TEST REQUIREMENTS.
5.1 Production Tests.
A visual examination must be performed on all components to verify proper materials, dimensions, finish, and quality of workmanship.
section 5. PRODUCTION TEST REQUIREMENTS. › 5.2 Production Test Records.
5.2 Production Test Records.
Records showing actual test results of all tests required by paragraph 5.1 must be maintained for a period of three years by the manufacturer.
Intentionally left blank.