Radar Vectors
Advisory Circular Cancelled Issued Feb 18, 2002 AAS-100 96 pages Copy saved Nov 18, 2026

AC 150/5220-10C Guide Specification for Water/Foam Aircraft Rescue and Firefighting Vehicles

Contains performance standards, specifications, and recommendations for the design, construction, and testing of a family of aircraft rescue and firefighting (ARFF) vehicles.

This document is no longer current. Cancelled by 150/5220-10D. Check the official source before relying on it.

Official source ↗ Open PDF

CANCELLED

Advisory U.S. Department of Transportation Circular Federal Aviation Administration

Subject: GUIDE SPECIFICATION FOR WATER/FOAM AIRCRAFT RESCUE AND FIRE FIGHTING VEHICLES

1. PURPOSE. This advisory circular (AC) contains performance standards, specifications, and recommendations for the design, construction, and testing of a family of aircraft rescue and fire fighting (ARFF) vehicles.

Subject: GUIDE SPECIFICATION FOR WATER/FOAM AIRCRAFT RESCUE AND FIRE FIGHTING VEHICLES

2. CANCELLATION. AC 150/5220-10B, Guide Specification for Water/Foam Aircraft Rescue and Fire Fighting Vehicles, dated October 20, 1997, is canceled.

3. APPLICATION. The Federal Aviation Administration (FAA) recommends the use of the guidance in this publication for the preparation of ARFF vehicle specifications. For airport projects David L. Bennett's signatureDAVID L. BENNETT Director, Office of Airport Safety and Standards

Date: 2/18/02 AC No: 150/5220-10C Initiated by: AAS-100 Change:

receiving Federal grant-in-aid assistance, the use of these standards is mandatory. At certificated airports, the use of equipment meeting these standards satisfies the requirements of Title 14 Code of Federal Regulations (CFR) Part 139, Certification and Operations, Land Airports Serving Certain Air Carriers, Subpart D-Operations, Subparagraph 139.317, “Aircraft Rescue and Fire Fighting: Equipment and Agents.” Features or design details not listed as required or optional in this document are not considered necessary unless a justification acceptable to the FAA is provided.

CANCELLED

CANCELLED

CONTENTS

CHAPTER 1. INTRODUCTION … 1

Section 1. General Characteristics … 1

1. DEFINITIONS … 1 2. EXPECTED USE … 1 3. VEHICLE CLASS … 1 4. RESERVED … 1

Section 2. Ergonomics … 1

5. CREW SPACE … 1 6. RIDE QUALITY … 1 7. CONTROLS … 2 8. SAFETY FEATURES … 2

Section 3. Design Criteria … 2

Section 3. Design Criteria … 2

9. PERFORMANCE … 2 10. FLEXIBILITY … 2 11. MAINTAINABILITY … 2 12. COMPONENT PROTECTION … 3 13. PAINTING, MARKING, AND LIGHTING … 3 14. INSULATION, WATERPROOFING, AIR CONDITIONING, AND WINTERIZATION … 3 15. MATERIALS … 4 16. THROUGH 19. RESERVED … 4

CHAPTER 2. AUTOMOTIVE SYSTEM … 5

Section 1. Frame … 5

Section 1. Frame … 5

20. BALANCE AND CLEARANCES … 5 21. DIMENSIONS … 5 22. LOAD RATING … 5

Section 2. Body Components … 5

23. COACH WORK … 5 24. COMPARTMENTS … 5 25. HANDRAILS … 6 26. RUNNING BOARDS, STEPS, WALKWAYS, AND TOWING DEVICES … 6

Section 3. Cab and Accessories … 6

27. CONTROLS … 6 28. CREW SPACE AND DOORS … 7 29. EQUIPMENT … 8 30. INSTRUMENTS AND WARNING LIGHTS … 8

Section 4. Driveline and Controls … 8

Section 4. Driveline and Controls … 8

31. AXLES … 8 32. BRAKE SYSTEM … 9 33. STEERING … 9 34. SUSPENSION … 10 35. TRANSFER CASE … 10

i

CANCELLED

36. TRANSMISSION … 10 37. WHEELS AND TIRE ASSEMBLY … 10

Section 5. Electrical System … 11

38. COOLANT HEATER … 11 39. LIGHTING AND MARKING SYSTEM … 11 40. POWER SUPPLIES … 12 41. STARTER … 12 42. WIRING … 12 43. RADIO EQUIPMENT … 13

Section 6. Engine and Accessories … 13

Section 6. Engine and Accessories … 13

44. COOLING SYSTEM … 13 45. EXHAUST SYSTEM … 14 46. FUEL SYSTEM … 14 47. GOVERNOR … 14 48. LUBRICATION … 14 49. POWER REQUIREMENT … 14 50. WINTERIZATION–OPTION … 15

Section 7. Automotive Performance … 15

51. ACCELERATION … 15 52. BRAKE SYSTEM … 15 53. DYNAMIC AND STATIC STABILITY … 15 54. ENVIRONMENTAL CONDITIONS … 15 55. GRADABILITY … 15 56. OPERATIONAL RANGE … 15 57. TOP SPEED … 16 58. OFF-ROAD HIGH-MOBILITY SUSPENSION … 16 59. DRIVER’S ENHANCED VISION SYSTEM (DEVS) … 16 60. THROUGH 69. RESERVED … 16

CHAPTER 3. FIRE EXTINGUISHING SYSTEMS … 19

CHAPTER 3. FIRE EXTINGUISHING SYSTEMS … 19

Section 1. Dry Chemical–Option … 19

70. AGENT CONTAINER(S) AND COMPONENTS … 19 71. AGENT DELIVERY PIPING AND VALVES … 19 72. PROPELLANT, PROPELLANT CONTAINERS, AND COMPONENTS … 19

Section 2. Clean Agent–Option … 20

73. AGENT CONTAINER AND COMPONENTS … 20 74. AGENT DELIVERY PIPING AND VALVES … 20 75. PROPELLANT, PROPELLANT CONTAINERS, AND COMPONENTS … 20

Section 3. Foam Concentrate System … 21

Section 3. Foam Concentrate System … 21

76. CONCENTRATE PROPORTIONER … 21 77. CONCENTRATE RESERVOIR AND PIPING … 21

Section 4. Water System … 22

78. PIPING, COUPLINGS, CONNECTIONS, AND VALVES … 22 79. WATER PUMPS AND PUMP DRIVE … 22 80. WATER RESERVOIR AND PIPING … 23

ii

CANCELLED

Section 5. Handlines, Reels, and Compartments … 24

Section 5. Handlines, Reels, and Compartments … 24

81. HANDLINES … 24 82. WOVEN JACKET HOSE AND REEL HOSE COMPARTMENTS … 24

Section 6. Turrets, Man-rated Aerials, and Undertruck Nozzles … 25

83. PRIMARY TURRET … 25 84. SECONDARY TURRET … 25 85. HIGH-REACH, EXTENDABLE TURRET–OPTION … 25 86. MAN-RATED AERIALS … 27 87. DUAL AGENT TURRET … 27 88. UNDERTRUCK NOZZLES … 27

Section 7. Agent System Performance … 28

Section 7. Agent System Performance … 28

89. COMPLEMENTARY AGENT SYSTEM–OPTION … 28 90. WATER/FOAM AGENT APPLICATORS … 28 91. THROUGH 99. RESERVED … 28

CHAPTER 4. QUALITY ASSURANCE … 33

Section 1. General Consideration … 33

100. CRITERIA FOR VEHICLE ACCEPTANCE … 33 101. TECHNICAL SERVICE, PERFORMANCE DOCUMENTATION, AND TRAINING … 33 102. NAMEPLATES AND INSTRUCTION PLATES … 34

Section 2. Certification of Performance … 34

Section 2. Certification of Performance … 34

103. COMPONENT MANUFACTURER'S CERTIFICATION … 34 104. VEHICLE MANUFACTURER'S CERTIFICATION … 35

Section 3. Prototype Vehicle Performance Test … 35

105. PROTOTYPE TEST LIST … 35 106. BRAKE SYSTEMS PERFORMANCE … 36 107. COMPLEMENTARY AGENT SYSTEM … 37 108. ELECTRICAL CHARGING SYSTEM … 40 109. BODY AND CHASSIS FLEXIBILITY … 41 110. WATER/FOAM AGENT SYSTEM … 42 111. GRADABILITY … 50 112. RADIO INTERFERENCE SUPPRESSION … 50 113. SIREN SOUND OUTPUT: DIRECTION AND MAGNITUDE … 51 114. STABILITY: DYNAMIC … 52 115. STEERING SYSTEM: RESISTANCE AND TURNING DIAMETER … 53 116. UNDERBODY CLEARANCES … 53 117. VISIBILITY: INCLUDED ANGLES FROM THE DRIVER'S SEAT … 54 118. VEHICLE INTERIOR NOISE LEVEL … 55 119. STABILITY: STATIC/SIDE SLOPE (TILT TABLE) … 55 120. RESERVED … 55

Section 4. Production Vehicle Performance Acceptance Tests … 55

Section 4. Production Vehicle Performance Acceptance Tests … 55

121. PRODUCTION TEST LIST … 56 122. ACCELERATION … 56 123. AIR COMPRESSOR CAPACITY … 56 124. BALANCE/WEIGHT DISTRIBUTION … 57 125. BRAKING CONTROL … 58

iii

CANCELLED

126. WATER/FOAM PROPORTIONER(S) TOLERANCE … 59 127. WATER/FOAM SOLUTION PUMP DISCHARGE STABILITY … 59 128. DUAL PUMP DISCHARGE STABILITY … 60 129. PRESSURE TEST OF PIPING AND CONNECTIONS … 61 130. PUMP AND ROLL CAPABILITY … 61 131. ROOF TURRET DISCHARGE RATE … 62 132. TOP SPEED … 62 133. STABILITY: STATIC/SIDE SLOPE (TILT TABLE) … 62 134. PIERCING/PENETRATION NOZZLE TESTING … 623

APPENDIX 1. DEFINITIONS … 1

APPENDIX 1. DEFINITIONS … 1

APPENDIX 2. OFF-PAVEMENT MOBILITY … 1

APPENDIX 3. EQUIPMENT FOR AIRCRAFT RESCUE AND FIRE FIGHTING OPERATIONS … 1

APPENDIX 4. PURCHASER ELECTION OF SUBSYSTEM COMPONENTS … 1

TABLES

1. Minimum Usable Water (Rated Capacity) … 1 2. Automotive Performance Standards … 18 2M. Automotive Performance Standards (Metric) … 19 3. Extinguishing Agent System Performance Standards … 30 3M. Extinguishing Agent System Performance Standards (Metric) … 31 3A. Extinguishing Agent System Performance Standards (High-Reach Extendible Turret–Option) … 32 4. Foam Quality Standards … 33

Appendix 3 A3-1. Worksheets For Subsystem Component Selection … 2

Appendix 3 A3-1. Worksheets For Subsystem Component Selection … 2

FIGURES

Appendix 2 A-2.1. Figure A-2.1. Location of Landing and Takeoff Accidents (Source: ALPA) … 4

iv

CANCELLED

CHAPTER 1. INTRODUCTION.

Section 1. General Characteristics.

1. DEFINITIONS. Terms with meanings unique or specifically related to aircraft rescue and fire fighting (ARFF) vehicle design, construction, and performance requirements are contained in Appendix 1.

Appendix 2 A-2.1. Figure A-2.1. Location of Landing and Takeoff Accidents (Source: ALPA) … 4

2. EXPECTED USE. This guide specification covers two classes of all-wheel drive, diesel-powered ARFF vehicles having a mechanical water/foam system designed for extinguishing flammable and combustible liquid fuel fires. The dry chemical and Clean Agent, or approved equivalent complementary agent systems described in Chapter 3, are acceptable optional additions to the basic vehicle when dictated by local operational needs. However, the primary function of the vehicles described in this guide specification is to

provide an optimum level of ARFF suppression capability for the lowest practical cost. These vehicles may also be suitable for other fire protection assignments at the airport. Vehicles complying with this basic specification meet the ARFF vehicle requirements of 14 CFR Part 139.

3. VEHICLE CLASS. The vehicle payload consists principally of the minimum usable (rated capacity) quantities of water shown in Table 1 and sufficient foam concentrate to mix at the appropriate concentration with twice that water quantity.

4. RESERVED.

Table 1. Minimum Usable Water (Rated Capacity).

Class Gallons Liters

1 1,500 5,685

2 3,000 and over 11,370 and over

Section 2. Ergonomics.

5. CREW SPACE.

a. All crew space shall be restricted to the interior of a fully enclosed cab with approved, 3-point restraints as minimum seat belts or shoulder harness system.

b. Where practicable, instruments shall be used in preference to warning lights. If warning lights are used, a means to readily test the condition of all warning light bulbs shall be provided.

c. Instruments and warning lights shall be displayed so that they will be useful, convenient, and visible to the driver.

d. The instrument panel(s) shall either be easily removable as units or hinged for back access. Quick disconnect fittings shall be used for all electrical connections to the instrument panel. All instruments, except liquid filled gauges, shall be illuminated. Labels for control and instruments should be backlit or illuminated.

e. All rotating or reciprocating parts, all parts with operating temperatures above 120° F (49° C), or that are electrically energized or are of such a nature or so located as to be a hazard to the safety of operating and maintenance personnel during their normal duties, shall be insulated, enclosed, or guarded as appropriate for the specific hazard and its location.

f. All space that is occupied or from which work is performed during operations, servicing, and maintenance of the vehicles shall be free from hazardous protrusions, sharp edges, cracks, or other elements that might reasonably be expected to cause injury to personnel.

6. RIDE QUALITY.

a. The design objective for the vehicle ride quality shall be to permit safe operation over rough roads and adverse terrain found at the airport of intended service at speeds of at least 35 mph (56 km/h) without causing injury to the operating personnel

CANCELLED

(wearing seat belts), loss of vehicle control, or damage to the vehicle.

b. The design objective for all vehicle and fire extinguishing system controls shall be to permit driving and fire fighting operations that do not require effort by operating personnel in excess of the limits specified in the current version of MIL-STD-1472, Human Engineering Design Criteria for Military Systems, Equipment and Facilities.

7. CONTROLS.

a. All the controls necessary for the full operation of the vehicle and for activating the fire fighting system shall be within reach of the driver. Controls for the fire extinguishing system(s) shall also be within easy reach of a second crew station or duplicated for that crew station. All cab-mounted controls shall be identified by function and/or limitation with permanent backlit labels.

b. Fire fighting equipment and controls located on the vehicle exterior shall be placed between 24 inches (61 cm) and 72 inches (183 cm) above the ground, catwalks, or deck plates, as applicable.

c. All controls located on the exterior of the vehicle shall be labeled with an illuminated permanent label identifying function and/or limitation.

8. SAFETY FEATURES.

a. A warning siren/device shall be provided, and it shall—

(1) Be a multitone, multivolume state-of-theart device commonly used in the industry on emergency vehicles. The control(s) shall be accessible to both the driver and a second crew member.

(2) Produce a minimum sound of 95 dB(A) at 100 feet (30 m) directly in front of the vehicle and 90 dB(A) at 100 feet (30 m) and 45 degrees left and right of front center.

(3) Have a speaker mounted as far forward and low as possible and be protected from drippings from the turret and water splashed up by the tires.

b. A horn shall be provided and mounted in accordance with National Fire Protection Association (NFPA) 1901 so as to achieve optimum sound projection to the front of the vehicle. A control button or horn ring shall be located at the steering wheel.

c. A “vehicle backing” warning device, audible up to 25 feet (7.6 m) behind the vehicle, shall be provided. Shifting the transmission into reverse shall activate this device. The volume of the warning device shall be self-adjusting based upon ambient noise.

Section 3. Design Criteria.

9. PERFORMANCE. The design objective for the vehicle and the fire extinguishing system shall be performance in accordance with Chapter 2, Section 7, Automotive Performance. Performance for the fire extinguishing system shall be in accordance with Chapter 3, Section 7, Agent System Performance. Manufacturers shall be required to identify their loaded apparatus’s center of gravity as well as the safe operating envelope of the loaded vehicle to include side slope maneuverability and high-speed cornering. Manufacturers shall provide a data plate that contains all the information, at a minimum, presented in Figure 1-4.5 of NFPA 414, Standard for Aircraft Rescue and Fire-Fighting Vehicles, current edition. This data plate shall be installed in the cab of the vehicle and visible to the operator.

10. FLEXIBILITY. The design objective for the vehicle frame, suspension, and mounting of major components shall be to provide the capability for diagonally opposite wheel motion up to 14 inches

(36 cm) above the ground without raising the remaining wheels from the ground or causing interference or parts failure.

11. MAINTAINABILITY. The vehicle design shall be such that it—

a. Uses the fewest number of different parts consistent with the specified performance.

b. Permits maintenance with commercially available, general purpose mechanic tools and equipment (metric sizes are permitted if required tools are “standard” and “commercially available” to the extent possible). The vehicle manufacturer shall provide and document in the maintenance manual introduction any special or nonstandard tools required and any unique test equipment required to perform operator/owner maintenance and service.

CANCELLED

c. Limits the number of tools and the variety of spare parts required for maintenance by such design practices as reducing the variety of bolt sizes, light bulb sizes, wire gauges, tubing, and pipe sizes as consistent with safety and performance requirements.

d. Uses disconnect plugs, receptacles, junction boxes, bus bars, multiple-line connectors in the electrical systems, and readily detachable fittings in hydraulic and pneumatic systems, as applicable. All disconnect points shall be clearly labeled. All hydraulic and pneumatic lines and electrical wires shall be color-, function-, or number-coded.

e. Includes pilots, guides, slides, carriages, or other features where such provisions can add to the ease of removal and installation or attachment of components.

f. Uses a fastener system that is easily disassembled and reassembled for all cabinets and body-work that must be removed for access for maintenance and removal of components for repair or replacement. Uses fasteners—not limited to brackets, nuts, bolts, washers, screws, and rivets—of stainless steel or other materials resistant to corrosion.

g. Locates drains, filler plugs, grease fittings, hydraulic line-bleeders, and checkpoints so that they are readily accessible and do not require special tools for proper servicing.

h. Ensures that the installation of each major subsystem or critical part can only be in its proper operating position.

i. Provides accessible connections, where needed, to attach troubleshooting, analytical, and diagnostic equipment to appropriate vehicle subsystems.

j. Operates with standard commercial lubricants. Grease and oil seals shall be of a design and located to provide accessibility for inspection, servicing, and replacement. Access to lubrication points shall be provided by means of an easy opening door or hinged panel. Lubrication fittings shall be located in accessible, protected positions. Parts or assemblies that are not readily accessible for direct lubrication, or are likely to be overlooked because of inaccessibility, shall have extended fittings. A safety chain shall attach filler caps to lubrication fill points where practical.

k. Includes, as optional, the installation of continuous duty cycle lubrication systems for suspension lubrication points and other mechanical

equipment joints to increase the duty cycle of components and extend the useful life of the vehicle.

12. COMPONENT PROTECTION.

a. All oil, hydraulic, air, water, foam concentrate, and electrical system conduits, tubing, and hoses shall be located in protected positions. They shall be secured to the frame or body structure and, except where a through-frame connector is necessary, shall be fitted with protective looms or grommets at each point where they pass through panels or structural members.

b. All radiator grills, louvers, lamps, tie rods, drive shafts, piping, and other vulnerable components shall be protected by component location or by guards adequate to prevent damage from brush, stones, logs, etc. likely to be encountered by the vehicle during offroad performance.

13. PAINTING, MARKING, AND LIGHTING. Vehicles shall be painted and marked in accordance with the standards of AC 150/5210-5B, Painting, Marking, and Lighting of Vehicles Used on an Airport.

14. INSULATION, WATERPROOFING, AIR CONDITIONING, AND WINTERIZATION.

a. Insulation shall be fire and water resistant and of a type that will not pack or settle. Provision shall be made to allow the drainage of water from between the walls by gravity flow. The average heat loss shall not exceed 0.24 BTU/ft2 (0.76 W/m²) per degree Fahrenheit per hour. All insulation that could be exposed to abrasion or damage from equipment storage or operator activities shall be provided with a protective covering. All insulation that will be located on the exterior of the vehicle shall be protected from damage or exposure by a permanent cover to be constructed to match the vehicle exterior.

b. All components shall be designed, installed, and/or protected so that their normal function will not be impaired by heavy rains, road splash, formation of condensation, or the spillage of extinguishing agents from nozzles and fittings, recharging operations, or leaks in the piping system.

c. The normal temperature design criteria shall be for vehicle use in a temperature range of 32° F (0° C) to 115° F (43.5° C).

d. If, in the judgment of the purchaser, the operational practices of the ARFF service at a specific airport warrant the use of air conditioning, a system that meets current automotive/truck and environmental

CANCELLED

protection standards for vehicle air conditioning may be specified by the purchaser. The use of the air conditioning shall not change the acceptable pass/fail criteria for any of the performance tests of the vehicle or the fire fighting system.

e. If, in the judgment of the purchaser, the climatic conditions combined with the normal operational procedures at a specific airport warrant the use of special freeze protection, a winterization system that meets the requirements of Paragraph 50 may be specified by the purchaser.

15. MATERIALS.

a. Materials not specifically covered by this specification or applicable referenced specifications or standards shall be of the best quality currently used in commercial practice for ARFF vehicle fabrication.

b. Dissimilar metals shall not be in contact with each other. Metal plating or metal spraying of dissimilar base metals to provide electromotively compatible abutting surfaces is acceptable. The use of dissimilar metals separated by suitable insulating material is permitted, except in systems where bridging

of insulation materials by an electrically conductive fluid can occur.

c. Materials that deteriorate when exposed to sunlight, weather, or operational conditions normally encountered during service shall not be used or shall have a means of protection against such deterioration that will not prevent compliance with performance requirements.

d. Protective coatings that chip, crack, or scale with age or extremes of climatic conditions or on exposure to heat shall not be used.

e. The use of proven, nonmetallic materials in lieu of metal is permitted if that use contributes to reduced weight, lower cost, or less maintenance and there is no degradation in performance or increase in long-term operations and maintenance costs.

16. THROUGH 19. RESERVED.

CANCELLED

CHAPTER 2. AUTOMOTIVE SYSTEM.

Section 1. Frame.

20. BALANCE AND CLEARANCES.

a. The weight shall be distributed as equally as practical over the axles and tires of the fully laden vehicle.

(1) The difference in tire load between tires on any axle shall not exceed 5 percent of the average tire load for that axle.

(2) The difference in load between axles shall not exceed 10 percent of the load on the heaviest axle.

(3) The front axle shall not be the most heavily loaded axle.

EXCEPTION: The front axle may be the most heavily loaded axle in those cases where options specified by the purchaser cannot be practically engineered to conform to this requirement. However, if the front axle is the most heavily loaded, the weight difference between it and any other axle shall not exceed 5 percent. In addition, none of the component ratings shall be exceeded to accommodate this deviation in the balance/weight distribution AND all other performance requirements of this specification shall be met.

(4) Under no circumstances shall axle and tire manufacturer's ratings be exceeded in an effort to comply with any of the above.

b. The fully loaded vehicle shall be able to meet the side slope stability standards of Table 2, Performance Parameter 2.

c. See Table 2, Performance Parameters 4 through 8, for standard clearances.

21. DIMENSIONS.

a. The overall height, length, and width of the vehicle shall be the smallest dimensions consistent with the rated payload for its class and the operational performance requirements of the vehicle.

b. Although payload and operational performance are of primary importance, costeffectiveness and local functional consideration (e.g., existing door, bridge, and tunnel clearances) may dictate that one or more specific dimensional requirements be specified by the purchaser.

22. LOAD RATING.

a. The functional load rating of the frame shall equal or exceed the actual gross vehicle weight (GVW). The GVW includes complete chassis; cab with attachments, accessories, and equipment; the body with rated agent payload, including a full complement of crew, fuel, lubricant, coolant, firefighter protective clothing, equipment, and breathing apparatus in appropriate numbers; and fire fighting handtools and appliances.

b. The frame shall not be altered during installation of the fire protection package in any way that will reduce its load rating.

Section 2. Body Components.

23. COACH WORK. Parts shall be fabricated from materials that will provide the lightest weight consistent with the needs for strength, as well as heat and corrosion resistance. Safety of the crew shall be a primary consideration in coach work, especially the protection of occupants during a roll over.

24. COMPARTMENTS. The compartments shall be of weather-tight construction and equipped with closures. Closures shall have positive holding mechanisms in both open and closed positions and may be of track/roll or hinge/swing type.

All compartments shall—

a. Be provided with weather proof lights that are switched to automatically light when compartment doors are opened and the vehicle master switch is in the “on” position.

b. Include vent(s) with a total of at least 10 squares inches (64.5 cm²) of ventilation.

c. Have a drain to allow collected water to run out under the vehicle.

CANCELLED

d. Be equipped with an indicator light in the cab or on the instrument panel and an audible signal to advise the operator when a compartment door is open.

e. All compartments shall contain a highly visible, permanently affixed label clearly stating the maximum weight that can be placed therein based upon tilt table certification testing.

25. HANDRAILS. Handrails or a guardrail shall be provided for personnel safety at all steps, walkways, and elevated workstations, including along the vehicle tank top or tank-top fill area. The rail material shall be heat and corrosion-resistant or provided with a low-maintenance, durable, and sunlight-, weather-, heat-, and corrosionresistant finish. The finish should be slip resistant.

26. RUNNING BOARDS, STEPS, WALKWAYS, AND TOWING DEVICES.

a. Running boards, step surfaces, ladder rungs, walkways, and catwalks shall have antiskid treads, deck plates, handrails, and guards, as applicable.

(1) The height between steps shall be less than 20 inches (50 cm).

(2) The lower steps shall be less than 24 inches (60 cm) from the ground. The lowermost

steps may extend below the angle of approach or departure or ground clearance limits if they are designed to swing clear.

(3) The tread of the bottom steps shall be at least 8 inches (20 cm) in width and succeeding steps at least 16 inches (40 cm) in width.

(4) The full width of all steps shall have at least 6 inches (15 cm) of unobstructed toe room or depth when measured from and perpendicular to the front edge of the weight-bearing surface of the step.

b. Catwalks and deck plates that provide access to equipment mounted on the vehicle shall withstand the loads imposed by personnel while performing normal service and operational functions.

c. Two towing hooks/eyes with shackles shall be attached directly to the frame rails at the front and rear of the vehicle. The purchaser may request a pintle hook having a 30,000-pound capacity rating be attached to the rear frame cross member of the vehicle if its presence will not interfere with other components necessary for the required performance. The towing devices may be allowed to intrude into the 30-degree approach angle in order to provide ease of connection if needed.

Section 3. Cab and Accessories.

27. CONTROLS. Unless otherwise noted, the following cab-mounted controls shall be provided as applicable for the safe and efficient operation of the vehicle:

Accelerator Pedal Agent Flow Control Air Conditioner Controls, if specified Brake Pedal Complementary Agent/System Activation, if specified Differential Lock Control Headlight Dimmer Control Heated Mirror Control, if specified Dome Light Switch Manual/Door Activated, with

white/red or green light selector switch as specified Engine Shutdown Switch Foam Concentrate Reservoir Control Valve Headlight Switch Heater/Defroster Controls Horn Control

Ignition Switch Master Electrical Disconnect Switch Panel Lights Switch with Dimmer Parking Brake Control Power Adjustable Mirror Control Siren Switch with Microphone Switch(es) for Exterior Lights, as specified in

Paragraph 39 Switch(es) for Emergency Beacon(s)/ Strobe(s) Switch(es) for Non-Emergency Amber (Yellow)

Beacon(s)/Strobe(s), if specified Starter Switch Tilt/Telescoping Steering Wheel Column Transmission Range Selector Turret Control Water Flow Control Valve Windshield Deluge System Control, if specified Windshield Wiper and Washer Controls

CANCELLED

28. CREW SPACE AND DOORS.

a. The cab shall—

(1) Have seats for a driver and at least one additional crewmember. The purchaser may specify additional crew positions if they have a local operational requirement.

(2) Have space for the instruments, radios, controls, and the safety equipment required for the number of firefighters intended to occupy the cab, without hindering crew operations.

(3) Have door(s) that open to at least a 90degree angle and are located on each side of the cab with appropriate steps and hand grabs. The location of vehicle components or mounted fire fighting equipment shall not obstruct the cab entrances/exits or obstruct visibility through the windshield or driver view of mirror.

(4) Be constructed and/or so mounted on the vehicle frame so as to meet the provisions of Paragraph 10.

(5) Be constructed to prevent cab collapse in the event of a vehicle rollover.

(6) Be weathertight and fully insulated in accordance with the provisions of Paragraph 14.

b. The cab roof shall have gutters of sufficient size to prevent foam and water from dripping on the windshield and side windows during turret operation. All cab fresh air vents/intakes shall be baffled and drained in such a way that wind-driven rainwater and/or water-foam solution sprayed on the vehicle cannot flow into the crew compartment through the air intakes. Fresh air intakes need to be placed and sealed so as to minimize ground fire and/or smoke from a fire environment from entering into the crew space.

c. All glass shall be a laminated or tempered, tinted safety type that meets applicable Federal standards and shall be free of imperfections that affect visibility.

d. The design and arrangement of the cab and components shall optimize visibility for a seated driver having an eye height of 31.75 inches (80 cm).

(1) The lateral field of vision shall be at least 90 degrees left and right of center.

(2) The ground must be visible to the driver at a point at least 15 feet (4.5 m) and beyond from the vehicle through the left two-thirds of the included angle of vision and 30 feet (9 m) from the vehicle through the right third of the included angle.

EXCEPTION: Proportional modification of the horizontal visibility range is acceptable for other than a left-mounted driver seat.

(3) The angle of visibility above the horizontal for the seated driver looking through the front cab windows shall be at least 5 degrees. For vehicles equipped with high-reach, extendible turrets, the angle of visibility above the horizon shall extend to a point 30 feet (9 m) above ground level at a distance of 15 feet (4.5 m) in front of the vehicle.

(4) Restriction of the horizontal angle of vision by window frames, corner and doorposts, etc. shall not exceed 7 degrees per obstruction.

(5) Forward vision for the driver, looking through the windshield between the forward corner posts of the cab, shall be unobstructed.

EXCEPTION: A center post is acceptable if the width is under 2 inches (50 mm) and there are no blind areas at a distance of 40 feet (12 m) from the vehicle when viewed by the driver using both eyes and sitting in a normal operating position.

e. Cab interior noise level at the driver's ear position (eye height in Paragraph (d) above) shall not exceed 85 dB(A) as specified in Paragraph 2-11.3 of NFPA 414.

f. An adjustable rearview mirror with a flat glass area of at least 60 square inches (385 cm2) on each side of the vehicle shall be included. In addition to each flat mirror, a wide-angle convex mirror of at least 7 square inches (45 cm2) shall be provided. Power adjustable mirrors are required, with their controls installed within easy reach of the driver. Heated mirrors may be specified by the purchaser.

g. At least one front overhead or two sidemounted (one on each side of the windshield) mirror(s) shall be provided to permit the vehicle operator a clear view of the area in front of the vehicle that is not within the operator's direct view.

h. The purchaser may specify a monitoring and data acquisition system (MADAS) for the collection of various performance measurements to monitor, as a minimum, the following:

CANCELLED

(1) Vehicle speed (2) Vehicle heading (3) Lateral acceleration (4) Vertical acceleration (5) Longitudinal acceleration and deceleration (6) Engine rpm (7) Throttle position (8) Steering input (9) Vehicle braking input (pedal position and

brake pressure) (10) Date, time, and location for all data

collected

The MADAS shall be capable of scoring the measurements and the time intervals, starting at least 120 seconds before and ending at least 15 seconds after any serious incident. The system shall be designed so that the data being recorded will not be lost or overwritten immediately after the incident due to the use of an emergency shutoff or a master electrical disconnect switch.

i. A lateral stability indicator that is preset by manufacturer for sensitivity and that provides both visual and audio signals and warnings to the driver shall be provided.

29. EQUIPMENT. The following shall be provided as applicable:

Air Conditioner, if specified Backup monitor, if specified Cab Dome Light, Red/White Crew Seats(s), with approved three-point seat belts Driver's Seat, up and down and fore and aft

adjustable, bucket-type with approved threepoint seatbelt FLIR Camera, with a 10-inch minimum monitor Heater/Defroster, with 200 BTU output per cubic

foot of cab space, blower capacity equal to one cab volume per minute, fresh air intake, and ducts to windshield

Navigation and/or Tracking subsystems of a

Driver’s Enhanced Vision System (DEVS), if specified Siren/Audible Emergency Warning Device Sun Visors, two or more Windshield Deluge System, if specified Windshield Washers, two or more with a large

capacity reservoir Windshield Wipers, two or more with delayed and multispeed capability

30. INSTRUMENTS AND WARNING LIGHTS. The following instruments and warning lights shall be provided in the cab as applicable:

Air Pressure (brake and other air-driven accessories) Complementary Agent Tank–Charged Light, if

applicable Compartment Door Indicator Differential Lock Indicator Beacon/Strobe Indicator (s) Engine Coolant Temperature Engine Oil Pressure Engine Tachometer(s) Foam Agent Tank Level Indicator, with test switch Foam Pump Pressure Indicator, if applicable Fuel Level Headlight Beam Indicator High-reach Turret Deployed Indicator, if a high-

reach turret is specified Illuminated Side/Slope Inclinometer Lateral Stability Indicator with visual and audible

alarm Low Air Pressure Warning Low Oil Pressure/High Water Temperature Audible/Visual Alarm Low Engine Coolant Audible/Visual Alarm Speedometer/Odometer Voltmeter, expanded scale Water Pump Pressure Water Tank Level Indicator, with test switch

Section 4. Driveline and Controls.

31. AXLES.

a. The axles shall be rated and certified as required by Paragraphs 100.a.(1) and 103.a as being suited for the intended use. The axle manufacturer's approved rating shall not be raised by the vehicle manufacturer to conform to the requirements of this specification.

b. Front and rear axles shall have adequate capacity to carry the fully loaded vehicle under all intended operating conditions. The maximum variation in axle tread shall not exceed 20 percent of the tire(s) sectional width at rated load.

c. Tractive power at each wheel shall be achieved by use of torque proportioning differentials or other suitable automatic devices that will ensure that

CANCELLED

each wheel of the vehicle is driven independently of the other wheels.

d. Front axles shall be equipped with steering drive ends designed to eliminate fluctuations in angular velocity of the wheels when cramped either left or right at all normal operating speeds.

32. BRAKE SYSTEM. A brake system shall be provided that has been tested and certified in accordance with the applicable requirements of Paragraphs 104, 105, and 106. The system shall include an all-wheel, split-circuit, power-assisted service brake; a modulatable emergency brake; and a parking brake.

a. Air supply. Vehicles supplied with air brakes shall have—

(1) A compressor that shall—

(a) Be engine driven.

(b) Have capacity sufficient to increase air pressure in the supply and service reservoirs from 85 to 100 psi (552 to 690 kPa) when the engine is operating at the vehicle manufacturer's maximum recommended revolutions per minute, in 25 seconds or less.

(c) Have the capacity for buildup of tank pressure from 5 psi (35 kPa) to the pressure required to release the spring brakes within 12 seconds.

(d) Have an automatic air drying system immediately downstream from the compressor.

(2) A service air reservoir that shall—

(a) Have a volume at least 12 times the total combined brake chamber volume at full stroke. If the reservoir volume, inclusive of supply lines and air dryer volumes, is greater than the minimum required, proportionately longer buildup time is acceptable using the following formula:

Actual reservoir capacity x 25 Maximum Time (sec) = Required reservoir capacity

and

(b) Have drains and safety valves, as necessary for safe and efficient operation. Drains shall be located at the lowest point of the vehicle and be accessible from the side(s) of the vehicle.

(3) When an auxiliary 110/220 VAC air compressor is specified by the purchaser, the shoreline electrical connection, which will release automatically (auto-eject) without damage to the vehicle upon starting the vehicle, shall be supplied.

(4) An automatic release (auto-eject) air connection for the charging of air tanks from an external air source.

(5) Visual and audible low air pressure warning devices. The low-pressure warning device shall be visible and audible from inside the cab.

b. Emergency Brake.

(1) The emergency brake shall be operable by the driver and shall be capable of modulation through the use of the service brake control.

(2) The emergency brake shall be capable of meeting the emergency brake stopping distance standard of Table 2, Performance Parameter 11, with the failure of only a single part in the service brake system other than failure of a common valve, manifold, brake fluid housing, or a break chamber housing.

c. Parking Brake. The parking brake shall be operable by the driver and shall meet the parking brake holding performance standard of Table 2, Performance Parameter 12.

d. Service Brake. A service brake powered by air, hydraulic, or air over hydraulic at the manufacturer’s option, which meets the applicable performance standards of Table 2, shall be acceptable.

(1) A chamber shall be provided for each brake for each wheel and shall be mounted so that no part of any chamber hangs below the bottom of the axle on which it is mounted.

(2) The service brake shall be capable of providing at least one power-assisted stop with the vehicle engine off that meets the service brake stopping distance standard of Table 2, Performance Parameter 10.

(3) An Anti-Lock Brake System (ABS) shall be provided and included for all wheels.

33. STEERING. All vehicles shall have powerassisted steering.

a. The power assist shall have sufficient capacity so no more than 15 pounds (6.8 kg) pull is necessary on

CANCELLED

the steering wheel rim to turn the vehicle wheels from lock to lock of the fully loaded vehicle when stationary.

b. The design of the steering mechanism shall permit manual steering to bring the fully loaded vehicle to a safe stop after power-assist failure.

c. The vehicle shall perform as follows when driven on a steering pad around a 100-foot (30 m) radius circle:

(1) With increasing speed, the steering angle shall increase; oversteer is not acceptable.

(2) The vehicle shall remain on the prescribed path until achieving a speed at least equal to the standard specified in Table 2, Performance Parameter 3.

d. The wall-to-wall turning diameter shall be no greater than three times the length of the vehicle.

e. A tilt/telescoping steering wheel/column shall be provided.

34. SUSPENSION.

a. The axles and suspension system shall be such that the total unsprung weight of the vehicle will not be greater than 20 percent of the in-service GVW.

b. Double-acting hydraulic shock absorbers or an equivalent energy-absorbing device shall be provided for all axles or bogies, as applicable.

c. Energy absorbing stops shall be installed so as to prevent damage to axles, drive shafts, the engine oil pan, or any other portions of the chassis from bottoming.

35. TRANSFER CASE.

a. The transfer case shall be certified as suitable for the intended service in accordance with the requirements of Paragraph 103.

b. A transfer case that is either separate or integral with the transmission, shall be acceptable, at the manufacturer’s option.

c. A single- or a two-speed transfer case, as required to meet the performance requirements, shall be acceptable, at the manufacturer’s option.

d. A transfer case that has either a front axle disconnect, a center differential with automatic or manual lockout, or an overriding clutch to compensate

for difference in travel between front and rear wheels, shall be acceptable, at the manufacturer’s option.

e. A transfer case that either engages the front and rear axles at all times, engages all axles automatically, or that is driver-operator selectable to engage all-wheel drive and that will not allow the vehicle to stall as long as the tires of engaged axle(s) have traction shall be acceptable, at the manufacturer’s option.

36. TRANSMISSION.

a. The transmission shall be certified as suitable for the intended service in accordance with the requirements of Paragraph 103.

b. The transmission shall be a continuous drive system. Either hydrostatic, hydrostatic/automatic, or automatic powershift, incorporating a torque converter with suitable torque ratio, shall be acceptable, at the manufacturer’s option. The use of a transfer case to achieve the required performance is acceptable, at the manufacturer’s option.

c. The transmission range selector shall have all positions clearly identified and back lit.

d. All drive-line components shall have the same power ratings; i.e., no reduction in transfer through bulkheads.

e. The hydraulic system shall include oil pumps, oil filter and screens, a hydraulic control system, and an oil cooling system capable of limiting the transmission temperature to the maximum recommended by the transmission manufacturer.

f. In addition to meeting the acceleration, gradability, and top speed standards of Paragraphs 51, 55, and 57, the transmission shall have sufficient spacing of intermediate ranges to provide a smooth, uniformly spaced transfer of power over the entire operating range.

37. WHEELS AND TIRE ASSEMBLY.

a. The wheel and tire assembly, including the recommended tire inflation pressure, shall be certified in accordance with Paragraph 103 as being suitable for the intended service.

b. Rim and tire rating shall conform to Federal Motor Vehicle Safety Standards (FMVSS), Standards No. 119 and 120, and applicable tire and rim

CANCELLED

association recommendations for the type and size of tires furnished.

c. All tires, rims, and wheels shall be identical.

d. The tires shall provide good lateral stability during off-road use in the terrain and climatic conditions expected at the intended airport. They shall also demonstrate safe on-road handling characteristics for operation on wet pavement.

e. Tires shall have a rated capacity at least equal to the load imposed on each tire measured at each wheel at the ground.

f. Tires shall be repairable and replaceable. There shall be a spare tire and wheel/rim assembly provided with, but not mounted on, the vehicle.

NOTE: The principle objective in the selection of the wheel and tire assemblies is to enhance the offpavement performance on the terrain encountered at the intended airport and, at the same time, meet highway automotive performance standards. However, the offpavement and overall handling characteristics of a vehicle depend on a number of other factors in addition to tire selection. Additional information to aid the purchaser during specification development, as well as during consultations with the vehicle and tire manufacturers, is provided in Appendix 2.

g. When specified by the purchaser, all tires (including spare) shall include beadlocks. A beadlock press shall also be provided for any quantity of vehicles purchased.

h. All wheels and tires shall be new; retreads are unacceptable for emergency service.

Section 5. Electrical System.

38. COOLANT HEATER. An engine coolant preheating device with thermostat shall be provided, which, at the manufacturer's option, may be of the immersion or circulating type. It shall have sufficient capacity to maintain the engine at the manufacturer's recommended temperature for rapid starting and immediate high initial engine performance.

39. LIGHTING AND MARKING SYSTEM.

a. The lighting and marking system, including reflectors, beacons, and clearance lights, shall satisfy the applicable State and Federal safety standards.

b. The system shall include—

(1) Two or more sealed beam halogen headlights with upper and lower driving beams.

(2) Two spotlights mounted on the roof or high-reach turret.

(3) At least one taillight and one stoplight or one combination taillight/stoplight on each side of the rear of the vehicle in the lower quadrant and a duplicate set of taillight/stoplight in the upper quadrant.

(4) Turn signals, front and rear, with selfcanceling control; a visual as well as audible indicator; and a four-way flasher switch.

(5) Reflectors, markers, and clearance lights meeting all applicable FMVSS.

(6) Nonglare-type engine compartment light(s), arranged to illuminate both sides of the engine and with switches(s) located in the engine compartment.

(7) Two backup lights, one installed on each side of the rear of the vehicle.

(8) One or more emergency flashing beacon(s) or strobe(s) as required by vehicle design to meet visibility requirements from the sides, front, and rear of the vehicle. For recognition, the color red shall be used alone or in combination with other colors if it is an operational requirement.

(9) Nonglare-type compartment light(s), arranged to illuminate the inside of all storage, maintenance access, and piping compartments.

c. The purchaser may specify the following options:

(1) Spotlights, quartz lights, fog lights, and area/service lighting.

(2) If, under normal local operational procedures, there are circumstances where it is desirable to identify the status of an ARFF vehicle as other than an ARFF vehicle in emergency response status, at least one amber (yellow) flashing beacon or strobe shall be provided in addition to the requirements of Paragraph 39.b.

CANCELLED

40. POWER SUPPLIES.

a. All components such as the alternator, circuit breakers, etc. shall be as waterproof/water resistant as the state-of-the-art permits without the use of marine quality components. They shall be accessibly mounted and protected against exterior and engine heat.

b. One of the following electrical systems shall be provided:

(1) 12-volt electrical and starting.

(2) 12-volt electrical/24-volt starting.

(3) 24-volt electrical and starting.

c. For 12-volt systems, alternators shall be provided that have a minimum curb idle charging rate of 160 amps. For 24-volt systems, an alternator shall be provided that has a minimum curb idle charging rate of 80 amps. In either case, the alternator(s) shall have a total current output capacity adequate to service the full operational electrical load of the vehicle, including all equipment and accessories specified. In addition, a 20percent reserve alternator capacity shall be provided. The alternator(s) shall have automatic regulation.

NOTE: Provisions to handle the additional load imposed by the winterization kit and/or air conditioning shall be included, when appropriate.

d. A weatherproof, grounded, polarized male plug(s) as required to service the anticipated electrical load, suitable for receiving 110-volts AC from an outside electrical supply, shall be provided.

(1) The plug(s) shall be mounted as specified by the purchaser.

(2) The plug(s) shall be wired to a built-in battery conditioner, the engine coolant pre-heating device, and the on-board air compressor, if specified.

(3) The plug(s) shall be designed to automatically release (auto-eject) as specified by the purchaser.

(4) The matching female receptacle(s) shall be provided with the vehicle.

e. A battery system shall be provided as follows:

(1) The system shall contain at least two 12-volt, maintenance free, batteries connected in an approved manner.

(2) The system shall have sufficient cold cranking battery capacity that meets the engine manufacturer’s recommendation for the lowest ambient starting temperature.

(3) Batteries shall be securely mounted and protected against mechanical damage, water spray, and engine and exhaust heat.

f. If an enclosed battery compartment is provided, it shall be adequately ventilated. The battery connections and the batteries shall be readily accessible for removal and installation, as well as for examination, test, and maintenance. The manufacturer may install roll out trays to provide the required accessibility.

g. A battery charger shall be provided on the vehicle and shall—

(1) Operate with inputs from 120 or 240 volts AC.

(2) Be able to supply an uninterrupted source of 12 or 24 volts DC.

(3) Provide full charge, when needed, to all batteries without interruption or causing any damage. It should have an automatic descending rate of charge input based on the status of the batteries being charged. It should incorporate the capability to descend from a high rate of input to a low rate and totally shut off to prevent overcharge of batteries.

(4) Be provided with grounded AC receptacle to allow automatic release (auto-eject) connection from an external electrical power supply.

(5) Have a built-in circuit to protect the battery from deep discharge or from damage during high current demands, such as those caused by starting the engine.

41. STARTER. An electric starting device shall be provided. When operating under maximum load, the current draw shall not cause a voltage drop sufficient to adversely affect the function of other electrical equipment required to operate during the startup process.

42. WIRING.

a. All wiring shall be numbered or color- or function-coded for proper identification. Wiring shall be of stranded conductors and of a wire gauge commensurate with the anticipated maximum electrical load of the circuit.

CANCELLED

2/18/02

b. Wires shall be insulated in accordance with the applicable standards of the Society of Automotive Engineers (SAE).

c. All connections shall be made with lugs or terminals mechanically secured to the conductors.

d. Wiring shall be secured in place and protected from heat, oil, lubricants, fire fighting agents, and physical damage. Appropriate circuit breakers shall be provided. Circuit breaker panels shall be easily accessible for service. A diagram and labeling scheme shall be affixed to the inside of the removable or hinged panel cover over the breakers. A copy of this diagram shall also be included in the maintenance manual.

e. Where wiring passes through sheet metal or structural components, rubber grommets shall be used to protect wiring and wiring looms. Precaution must be taken in all areas to guard against chafing or excessive strain.

43. RADIO EQUIPMENT.

a. Provisions shall be made by the purchaser to mount the radio(s) and the associated controls so they are operable by both the driver and at least one other crewmember without leaving the cab or removing their seat belts. The mounting provisions shall take into consideration the fact that radio operating equipment may include boom/microphone headsets with appropriate controls, radio interconnects, and remote or foot-operated push-to-talk switches, as specified by the purchaser. If a vehicle is to be equipped with headsets, storage boxes shall be provided to protect this

AC 150/5220-10C

equipment. The layout of headset controls should allow the headset wires to come from behind the operator so that the wires do not stretch across the cab.

b. Radio mounting locations shall be located so as to—

(1) Not restrict or interfere with the operation of any existing equipment or accessories.

(2) Not restrict cab visibility through the windshield.

(3) Not cause a hazard or obstruction to personnel.

c. The vehicle shall be wired and equipped as follows:

(1) Dedicated radio leads shall be provided to the dash instrument panel and marked and tagged with permanent tags.

(2) The radio power lead(s) shall be provided with circuit protection separately for each.

(3) The radio leads shall be 12 volts, negative ground.

d. The vehicle shall be provided with radio interference protection in accordance with SAE J551/4, Test Limits and Methods of Measurement of Radio Disturbance Characteristics of Vehicles and Devices, Broadband and Narrowband, 150kHz to 1000MHz, or an equivalent radio interference suppression standard.

Section 6. Engine and Accessories.

44. COOLING SYSTEM.

a. The vehicle manufacturer shall certify and provide appropriate documentation in accordance with Paragraphs 100.a(2) and 104 that the complete cooling system installation is suitable for the intended service.

b. The cooling system shall be provided with an automatic thermostat.

c. If a liquid-cooled system is provided, it shall—

(1) Have the capacity to stabilize the engine coolant temperature within the engine manufacturer's prescribed limits under operational conditions at the

ambient temperature range normally encountered at the airport.

(2) Have drain cocks installed at the low point of the cooling system and at such other points as may be necessary to drain the system completely.

d. If an air-cooled system is provided, it shall have the capacity to stabilize the cylinder head and oil temperatures within the engine manufacturer's prescribed limits under operational conditions at the ambient temperature range normally encountered at the airport.

e. When provided, radiator or air inlet shutters shall be automatic and “fail safe” in the open position.

CANCELLED

f. A cooling system filter/conditioner shall be provided.

45. EXHAUST SYSTEM.

a. The vehicle manufacturer shall certify that the exhaust system is suitable for the intended service.

b. The engine exhaust system shall be constructed of rust-resistant materials and shall be designed and installed so as to prevent the discharge of exhaust toward the ground, engine, or cab air intake or onto vehicle tires. A curved exhaust stack or a straight exhaust pipe with rain cap shall be provided as specified. Exhaust termination requirements that conform with existing Fire Station Diesel Exhaust Entrapment Systems shall be provided, as required.

c. The exhaust system exit shall be located to prevent exhaust gasses from entering the closed cab under all operational conditions and shall include a suitable heavy-duty, commercially available muffler.

d. System components shall be protected from damage that could result from traversing off-road terrain.

e. ARFF vehicle/engines must meet all applicable Federal emission standards and regulations.

46. FUEL SYSTEM.

a. The vehicle manufacturer shall provide a fuel system that meets the engine manufacturer's installation approval and shall certify that the fuel system is suitable for the intended service.

b. All components shall be installed in a protected location or otherwise protected from operational damage, exhaust heat, and exposure to ground fires.

c. The fuel tank(s) shall—

(1) Be constructed of an approved material.

(2) Have an accessible drain plug at the bottom of the fuel tank.

(3) Have a filler pipe (accessible from outside of the cab) that is at least 2.25 inches (5.7 cm) in diameter.

(4) Have sufficient capacity to provide for a minimum of 30 miles (48 km) of highway travel at

45 mph (73km/h) average plus 2 hours of pumping at the full-rated discharge.

(5) Be so located and mounted that it will prevent gravity feed.

d. An approved filter, mounted in an accessible location, shall be provided for each fuel supply line. The fuel supply line filter should be installed in such a manner that allows the free flow fueling of the vehicle without causing back ups and spills.

e. A fuel water separator shall be provided, and heated if specified.

47. GOVERNOR. An engine governor that will not adversely affect the automotive or extinguishing agent system performance shall be provided. The governor shall be set to limit engine speed so that it cannot exceed the maximum rpm recommended by the engine and driveline component manufacturers.

48. LUBRICATION.

a. The engine and transmission shall operate efficiently and without detrimental effect to any drive train components when lubricated with standard, commercially available lubricants in accordance with the recommendations of the engine and transmission manufacturers.

b. The engine oil and transmission fluid filters shall be of the full-flow type with a replaceable spin-on element.

c. All moving parts requiring lubrication shall have a means of providing for such lubrication. There shall be no pressure lubrication fittings where their normal use would damage grease seals or other parts.

d. The vehicle shall be serviced prior to delivery with lubricants, brake and hydraulic fluids, and a cooling system fluid suitable for use in the temperature range expected at the airport.

49. POWER REQUIREMENT.

a. The engine(s) shall be an internal combustion diesel capable of developing the torque and horsepower needed to meet the automotive performance standards in Table 2 and the extinguishing agent discharge performance standards in Table 3. This power requirement shall be achieved without exceeding a “no load” governed speed at the peak of a certified gross brake horsepower (bhp) curve.

b. The engine shall be capable of meeting the specified performance standards while operating on commercial grade diesel fuel.

CANCELLED

50. WINTERIZATION–OPTION.

a. Vehicles purchased for use in areas where it is common industrial practice to winterize vehicles shall have a winterization kit installed.

b. The winterization kit shall not detract from the performance of the vehicle or the fire fighting system in ambient temperatures up to 115° F (43.5° C).

c. The winterization kit shall provide sufficient insulation and heating capacity, by means of hot circulating liquids and forced air heat exchangers, to permit satisfactory operation of the vehicle and fire fighting systems for a period of at least 2 hours at ambient temperatures as low as -40º F (-40° C) with the vehicle fully operational and the engine running. At the end of this 2-hour period, the vehicle shall be capable of successfully discharging its agent(s).

Section 7. Automotive Performance.

51. ACCELERATION. Each vehicle shall meet the applicable standard of Table 2, Performance Parameter 9.

52. BRAKE SYSTEM. The stopping and holding performance for each type of brake shall meet the applicable standards of Table 2, Performance Parameters 10, 11, and 12.

53. DYNAMIC AND STATIC STABILITY. The vehicle shall be able to:

a. Pump while rolling in both directions across a 20-percent (12-degree) side slope with extinguishing agents being discharged in any direction of turret azimuth at maximum-rated turret capacity without unanticipated stream interruption or vehicle instability. Pumping capacity shall supply an intermittent discharge, as desired.

b. Remain stationary while headed in either direction across a 20-percent (12-degree) side slope and while the steering is being moved to a maximum turning angle both right and left without any vehicle instability.

c. Meet the applicable side slope stability standard of Table 2, Performance Parameter 2.

d. Meet the applicable dynamic balance standard of Table 2, Performance Parameter 3.

54. ENVIRONMENTAL CONDITIONS. The vehicle shall be capable of withstanding the following conditions without detrimental effect to subsequent operation of the vehicle or any of the fire extinguishing systems:

a. Dust particles, as encountered in desert areas.

b. The corrosive effects of salt fog.

c. Material decay from fungus and mildew.

d. Relative humidity up to 100 percent, as well as wind driven snow, sleet, rain, and vehicle selfsplashing of water.

e. Ambient temperature ranging from 32° F to 115° F (0° C to 43.5° C). (See Paragraph 50 for winterization.) If winterization is necessary, the temperature performance range shall extend to at least -40° F (-40° C).

55. GRADABILITY. The vehicle shall be able to—

a. Ascend a smooth, dry, paved road having a 20-percent grade and maintain a speed of at least 8 mph (13 km/h).

b. Ascend, stop, start, and continue ascending and descend, stop, start, and continue descending on a 20-percent grade at a speed of at least 2 mph (3.2 km/h) with extinguishing agents being discharged at maximum-rated capacity from the primary turret(s).

c. Ascend and descend a dry, hard surface incline having a 50-percent grade at not less than 1 mph (1.6 km/h).

d. Climb a vertical wall at least 18 inches (45 cm) high and negotiate terrain that will deflect the opposite wheels of the truck in alternatively contrary directions at least 14 inches (36 cm) without the remaining wheels losing traction.

56. OPERATIONAL RANGE. The fully loaded vehicle shall be able to—

a. Operate continuously for 25 miles (40 km) at speeds up to 60 mph (96 km/h). The test route shall include agricultural lands, paved and unpaved roads, and grades typical of those encountered at the intended airport. During this performance evaluation, the

CANCELLED

vehicle shall operate in all-wheel drive. At least 5 miles (8 km) of this operation shall be off-road travel.

b. Operate on smooth, dry, level pavement through a range from 1 mph (1.6 km/h) to at least 10 mph (16 km/h) while discharging agents from the primary turret(s) at rated maximum capacity without interruption.

c. Negotiate pooled water to a depth of 2 inches (5 cm) for a distance of at least 150 feet (45 m) at a speed of at least 40 mph (65 km/h) without engine flooding/stalling, loss of directional control, loss of braking, or electrical system(s) shorting.

d. Operate for 10 minutes on dry, paved roadway at not more than 2 mph (3.2 km/h) at an engine speed that does not result in rough, irregular operation.

e. Ascend a dry, paved incline having an 8percent grade for a distance of 0.25 mile (0.4 km) at a speed of not less than 20 mph (32 km/h).

f. Negotiate (J Turn) a 90-degree, 150-foot radius turn at 30 mph (48 km/h) on smooth, dry, level pavement without loss of directional control or stability.

57. TOP SPEED. The vehicle shall be able to consistently reach a top speed of 65 mph (104 km/h) and maintain a constant speed of at least 60 mph (96 km/h) on typical paved, level (grades of less than 1 percent) highway surfaces for a minimum distance of 20 miles (32 km) without showing overheat symptoms in any portion of the cooling system or power train.

58. OFF-ROAD HIGH-MOBILITY SUSPENSIONS.

a. An off-road, high-mobility suspension system resulting in no more than 0.5 g rms acceleration at the seat of the vehicle when traversing an 8-inch (24 cm) half round at 35 mph (56 km/h) shall be provided. Such suspension systems include, but are not limited to, independent, passive struts, semi-active, active/reactive, and articulated.

b. If specified by the purchaser, the system shall include a central tire inflation/deflation system supporting an off-road response at 35 mph (56 km/h) when operating within the runway safety area over similar terrain near the improved surface areas of the

airfield. Typically, this area has been moderately graded, has had most major obstructions removed, and has a sod cover.

59. DRIVER’S ENHANCED VISION SYSTEM (DEVS). DEVS equipment can aid normal operations and provide an additional margin of safety for airport rescue response during periods of very low-visibility operations. DEVS equipment improves emergency response time during periods of low visibility, reduces the probability of secondary accidents often associated with poor weather and low-visibility conditions, and improves command and control in the event of an aircraft incident or accident. A complete DEVS comprises three subsystems: night vision, navigation, and tracking. The provision of each subsystem shall be subject to the criteria below. Because of the complexity of a DEVS, procurement and installation may be optional and by separate contract and shall comply with AC 150/5210-19, Driver’s Enhanced Vision System (DEVS).

a. Night vision. The purpose of the night vision subsystem is to improve the ARFF vehicle driver’s ability to see at night and through smoke, fog, and adverse weather; it consists of a Forward Looking InfraRed (FLIR) camera and a minimum 10-inch monitor in the cab. This subsystem shall be provided on all vehicles.

b. Navigation. Using a differential GPS and a moving map display inside the cab, the navigation subsystem shows ARFF vehicle drivers their location, the accident site, and the path between to ensure rapid advance toward the site. When the airport is required to have a Surface Movement Guidance and Control System (SMGCS), the purchaser may specify the addition of this system. If specified, it shall be compatible with an existing tracking subsystem.

c. Tracking. The vehicle tracking subsystem allows an overview of all vehicles at the command center and provides reliable digital communications with vehicles. It is composed of a display at the command center and a digital radio datalink between the command center and vehicles. This subsystem shall be provided when the airport is required to have a SMGCS, the subsystem does not presently exist at the airport, and it is specified by the purchaser.

60. THROUGH 69. RESERVED.

CANCELLED

Table 2. Automotive Performance Standards

PERFORMANCE PARAMETER FOR FULLY

PERFORMANCE PARAMETER FOR FULLY

LOADED VEHICLE VEHICLE CLASS

1 2

1. Minimum Rated Water Capacity (gallons): 1,500 3,000 and over

2. Side Slope Stability:

Degrees

Percent Grade

30°

58%

30°

58%

3. Dynamic Balance: Minimum Speed on 100-foot Radius Circle (mph) 22 22

4. Approach and Departure: Angles 30° 30°

5. Interaxle Clearance: Angle 12° 12°

5. Interaxle Clearance: Angle 12° 12°

6. Underbody Clearance: 18" 18"

7. Underaxle Clearance at Differential Housing Bowl:

13" 13"

8. Wall-to-Wall Turning Diameter: Less than 3 x vehicle length

9. Maximum Acceleration Time from 0 to 50 mph (seconds): 25 35

10. Service Brake:

Stopping Distance from: 20 mph 40 mph

9. Maximum Acceleration Time from 0 to 50 mph (seconds): 25 35

Hold Fully Loaded Vehicle:

Maximum 35' Maximum 131'

40' 160'

Minimum 50% grade Ascending and Descending

11. Emergency Brake:

Stopping Distance from 40 mph

Maximum 288'

12. Parking Brake:

Hold Fully Loaded Vehicle

Minimum 20% grade Ascending or Descending

13. Evasive Maneuver Test (NATO Lane Change):

35 mph

14. J-Turn Test: 90-degree, 150-foot Radius Turn

14. J-Turn Test: 90-degree, 150-foot Radius Turn

30mph

CANCELLED

Table 2M. Automotive Performance Standards (Metric)

PERFORMANCE PARAMETER FOR

FULLY LOADED VEHICLE VEHICLE CLASS

1 2

1. Minimum Rated Water Capacity (liters): 5,685 11,370 and over

2. Side Slope Stability:

Degrees

Percent Grade

1. Minimum Rated Water Capacity (liters): 5,685 11,370 and over

30°

58%

30°

58%

3. Dynamic Balance: Minimum Speed on 30meter Radius Circle (km/h)

35 35

4. Approach and Departure: Angles 30° 30°

5. Interaxle Clearance: Angle 12° 12°

6. Underbody Clearance (cm): 46 46

7. Underaxle Clearance at Differential Housing Bowl (cm):

33 33

8. Wall-to-Wall Turning Diameter: Less than 3 x vehicle length

9. Maximum Acceleration Time from 0 to 80 km/h (seconds): 25 35

9. Maximum Acceleration Time from 0 to 80 km/h (seconds): 25 35

10. Service Brake:

Stopping Distance from: 32 km/h 64 km/h

Hold Fully Loaded Vehicle:

Maximum 11 m Maximum 40 m

14 m 48 m

Minimum 50% grade Ascending and Descending

11. Emergency Brake:

Stopping Distance from 64 km/h

Maximum 86 m

12. Parking Brake:

Hold Fully Loaded Vehicle

Minimum 20% grade Ascending or Descending

13. Evasive Maneuver Test (NATO Lange Change):

56km/h

14. J-Turn Test: 90-degree, 46-meter Radius Turn

14. J-Turn Test: 90-degree, 46-meter Radius Turn

48km/h

CANCELLED

CHAPTER 3. FIRE EXTINGUISHING SYSTEMS.

Section 1. Dry Chemical–Option.

70. AGENT CONTAINER(S) AND COMPONENTS.

a. The dry chemical container(s) shall—

(1) Be constructed and stamped in accordance with the American Society of Mechanical Engineers (ASME) Code for Unfired Pressure Vessels.

(2) Be certified in accordance with Paragraph 103.c.

(3) Be able to hold at least 450 usable pounds (204 kg) of a potassium-based dry chemical fire extinguishing agent.

(4) Have an accessible fill opening that is easy to open and close and be provided with a compatible funnel to permit filling from dry chemical storage containers. The overall design shall allow filling without the removal of any of the extinguisher piping or any major component other than the fill cap.

(5) Have a pressure relief device conforming to appropriate ASME codes that will protect both the container and the low-pressure piping.

(6) Include a gauge that indicates the pressure in the agent container at all times.

b. A check valve shall be provided in the gas piping to prevent the agent from being forced back into the propellant gas line.

c. A quick-acting agent system activation control shall be accessible to the seated driver and at least one other crew position. A similar control shall be located near the agent handline.

d. The agent pressurization system shall ensure fluidization of the dry chemical at the time of activation. Designs that include the automatic movement of the chemical or chemical container to help fluidize the contents shall also include a manual operating feature.

e. There shall be provisions for purging agent from all piping and hose after use without discharging the remaining chemical. Also, there shall be provisions for the depressurization of the chemical container without the loss of the remaining chemical.

f. Dash pressure gauges shall be installed that, when the system is activated, will allow the vehicle operator to determine the propellant reservoir status as well as the system operating pressure.

71. AGENT DELIVERY PIPING AND VALVES.

a. The piping, couplings, and valves shall be sized to provide the gas flow into the system and the agent flow out of the chemical container needed to meet the requirements of Table 3, Performance Parameter 1.a and b.

b. All piping and fittings shall conform to the appropriate ASME code. The completed system shall be designed and installed so as to withstand the recommended working pressure of the system.

c. The integrity of the installed discharge piping shall be tested at a pressure equal to 150 percent of the system working pressure.

d. Material for all piping, couplings, and valves shall be resistant to agent, weather, and galvanic corrosion.

e. Piping shall be securely mounted and provided with flexible couplings where needed to minimize stress.

f. When more than one agent discharge outlet is provided, the size and design of piping, pressure regulators, and fittings shall provide design flow to each outlet.

g. All valves shall be of the quarter-turn type, selected for ease of operation and freedom from leaks.

72. PROPELLANT, PROPELLANT CONTAINERS, AND COMPONENTS.

a. The propellant gas shall be either dry nitrogen or dry air. Sufficient container capacity shall be provided to ensure enough gas to discharge all of the agent and to permit purging of all pipes and hose lines after use.

b. All propellant gas cylinders and valves shall comply with U.S. Department of Transportation (DOT) requirements. Cylinders shall bear the DOT marking, including evidence of a current hydrostatic test and shall be certified in accordance with Paragraph 103.f.

CANCELLED

c. In addition to the provisions in Paragraph 70.f, pressure gauges shall be provided on the agent tank and propellant tank that will indicate the pressure on the propellant gas system downstream of the pressure regulator and in the propellant cylinder at all times.

d. Cylinder valves, gauges, and piping shall be arranged or protected to preclude accidental mechanical damage during fire fighting operations.

e. The pressure reduction system shall automatically reduce the normal storage cylinder pressure to (and hold it at) the designed operating pressure of the dry chemical container. The regulator may be of a type without pressure indicating gauges.

(1) Pressure regulating devices shall be equipped with a spring-loaded relief valve that will relieve any excess pressure that may develop in the regulator.

(2) All pressure regulating devices shall be sealed or pinned at the designed operating pressures after final adjustment by the system manufacturer and shall be certified in accordance with Paragraph 103.g.

(3) Regulators must be of a high-flow variety that allows a rapid buildup time for system pressure for a full system charge and operation.

f. A device shall be provided that allows for servicing the propellant cylinder by one person from ground level. The purchaser may specify that the device be manual or electric.

Section 2. Clean Agent–Option

Section 2. Clean Agent–Option

73. AGENT CONTAINER AND COMPONENTS.

a. The container material shall be suitable for the storage of Clean Agent and shall be constructed in accordance with ASME Code for Unfired Pressure Vessels and stamped. The container shall have—

(1) A capacity of at least 460 pounds of Clean Agent.

(2) A fill coupling of sufficient size to allow agent tank filling without loss of agent. It shall permit tank filling without the removal/disconnection of any piping or major components. The fill coupling shall be provided with a dust cap secured to the coupling with a safety chain.

(3) A means of determining the contents of the container as a guide in recharging partial loads and to prevent overfilling of the tank.

(4) A gauge that indicates the pressure in the agent container at all times.

b. A means of pressure relief conforming to appropriate ASME codes shall be provided for the chemical container and piping. A check valve shall be provided in the gas piping to prevent agent from being forced back into the propellant gas line.

c. The manufacturer shall make provisions for the purging of agent from the discharge piping and hose without discharging the chemical remaining in the container and for the depressurization of the chemical container without the loss of the remaining chemical.

74. AGENT DELIVERY PIPING AND VALVES.

a. The piping, couplings, and valves shall be sized to provide the gas flow into the system and the agent flow out of the chemical container needed to meet the requirements of Table 3, Performance Parameter 2.

b. The applicable requirements of Paragraph 71.b through 71.g also apply.

75. PROPELLANT, PROPELLANT CONTAINERS, AND COMPONENTS. The requirements of Paragraph 72 also apply.

CANCELLED

Section 3. Foam Concentrate System.

76. CONCENTRATE PROPORTIONER.

a. A foam concentrate proportioning system shall be provided to control the ratio of foam concentrate to water in the water/foam solution being discharged from all orifices normally used for ARFF operations.

(1) The proportioning system for a 6-percent concentrate shall be sufficiently accurate to provide for the discharge of finished foam within the range of 5.5percent to 7-percent foam concentrate in the discharged water/foam solution.

(2) If a foam concentrate other than 6 percent is used, the precision range shall be modified in direct ratio. Thus, a 3-percent concentrate shall be in the 2.8to 3.5-percent concentrate range in the discharged solution.

b. This precision shall be maintained for all individual discharges and for the maximum simultaneous discharge rate of all turrets, handlines, and ground sweeps while delivering the quantity of concentrate required to meet the agent discharge requirements of Table 3.

77. CONCENTRATE RESERVOIR AND PIPING.

a. Materials used in reservoir construction and piping shall be compatible with the foam concentrate, the water/foam solution, and water and shall not be subject to corrosive or acidic reaction caused by foam concentrate or water.

b. A rigid or a flexible foam concentrate reservoir shall be acceptable, at the manufacturer’s option.

(1) If the reservoir is separate from the water tank, the mounting of the reservoir shall limit the transfer of torsional strains from the chassis to the reservoir.

(2) The reservoir shall be separate and distinct from the crew compartment, engine compartment, and chassis and removable as a unit.

(3) The reservoir(s) shall have a working capacity sufficient for two tanks of water based on the percent foam concentrate used at the airport.

(4) Flexible reservoirs shall be supported in a manner that does not depend on the fluid level in either the foam or water reservoirs for its structural integrity.

(5) For other than lifetime warranted tanks, provisions shall be made for access for internal and external inspection and service. Reservoirs large enough to require baffles shall be provided with access to each baffled compartment.

(6) The reservoir shall be fitted with a sump, complete with antiswirl baffles, and a 1.5-inch (38 mm) minimum diameter drain with a valve and an accessible control.

(7) The reservoir outlet(s) shall be located above the bottom of the sump and shall permit a continuous flow of foam concentrate to the proportioning system with that system supporting the discharge standards of Table 3 during the discharge of two consecutive tanks of water.

(8) Reservoirs shall be vented to permit the required fill rate without exceeding the design working pressure and to permit emptying at the maximum design flow rate without danger of collapse. The vent outlets shall prevent spillage of foam concentrate on vehicle components.

c. The fill system shall be capable of delivering foam concentrate to the reservoir at a rate at least equal to the maximum use rate of the foam proportioning system.

(1) The bottom fill connection shall be provided and shall be no more than 60 inches (150 cm) from the ground. The inlet shall be fitted with stainless steel strainers of 1/4-inch (6 mm) mesh and shall have check valves or be so constructed that no more than 0.25 gal (1l) of foam is lost from the reservoir during connection or disconnection of the foam resupply line. An isolation valve shall be installed on the foam line as it leaves the tank to allow easy maintenance on foam plumbing.

(2) A top fill opening shall be provided and equipped with a No. 10 gauge mesh, corrosion resistant (stainless steel or equal) screen, and a 5-gallon agent container opener to permit the rapid emptying of 5gallon containers into the reservoir(s). The fill line from the trough shall introduce foam concentrate into the reservoir so as to minimize foaming.

d. The foam concentrate piping shall be sized to permit the flow rates needed to meet the agent discharge requirements of Table 3 and shall be arranged to prevent water from entering the foam reservoir.

CANCELLED

e. The foam concentrate piping shall be so concentrate pumps, can be flushed with water from the arranged that the entire system, including any foam water tank without contaminating the foam reservoir.

Section 4. Water System.

78. PIPING, COUPLINGS, CONNECTIONS, AND VALVES.

a. A pressure relief valve shall be fitted to the discharge system that is set to ensure discharge standards can be met and that surges above the designed operating pressure are relieved.

b. Hose connections shall have National (American) Standard fire hose coupling threads.

EXCEPTION: Adapters, securely attached to each outlet, shall be acceptable if local couplings do not meet National (American) Standards as specified in NFPA 1963, Standard for Screw Threads and Gaskets for Fire Hose Connections, and the outlet(s) with adapters do not add to the width or length of the vehicle.

c. All water system piping on the suction side of the pump shall be tested to detect leaks. All water and foam solution discharge piping, together with the agent pump(s), shall be tested at 150 percent of the normal system operating pressure.

d. If two pumps are used, they shall be arranged in parallel with a manifold so that either or both may supply any discharge outlet at the required operating pressure. During single pump operation, total discharge capacity may be proportionally reduced.

e. Piping, couplings, and valves shall be sized to provide agent flow to all discharge devices operating to the applicable standards of Table 3.

f. A drain shall be provided in the suction system at the lowest point with a valve for draining all of the liquid from the pumping system.

g. A drainage system, with collector tubing from the low points on pump(s) and piping, shall be provided.

h. All valves shall be selected for ease of operation and leak-free design.

i. Material for all piping, couplings, and valves shall be selected to avoid corrosion.

j. Piping shall be securely mounted and provided with flexible couplings to minimize stress from chassis flexing. Union, gasketed, or fittings shall be provided where required to facilitate removal of piping.

k. The purchaser may specify a limited structural exterior panel, which includes—

(1) Engine instruments and pump controls, including a tachometer, an oil pressure gauge, a temperature gauge, and a pressure control; pump shift; manual metering control; two compound suctionpressure gauges; water tank isolation valve; and panel lights.

(2) Either one or two 2-1/2-inch discharged valves shall be provided. Each discharge valve shall be provided with pressure gauge and bleeder. One manual metering control shall be provided.

(3) One 2-1/2-inch and one large diameter suction inlet connection with bleeder shall be provided, if specified.

l. A priming pump and reservoir shall be provided if specified.

79. WATER PUMPS AND PUMP DRIVE.

a. The water pump drive, if common with the vehicle drive, shall have sufficient power to meet the automotive performance and water/foam agent discharge standards of Tables 2 and 3, individually and simultaneously, as applicable.

b. If an independent pump engine is used, it shall—

(1) Have fuel, electrical, lubrication, hydraulic, and coolant requirements that are compatible with the chassis engine.

(2) Have sufficient power capacity to meet the water/foam agent discharge standards of Table 3 under all normal vehicle operational modes and environmental conditions.

(3) Be certified by the manufacturer as suitable for the intended service.

CANCELLED

c. The water pump(s) shall—

(1) Have sufficient capacity to supply the water/foam solution at the pressures and volumes required to simultaneously fulfill the discharge standards of Table 3.

(2) Be a centrifugal type. The manufacturer may provide either single- or multiple-stage pumps.

(3) Be gravity primed from the vehicle reservoir, regardless of the water level in the tank. The associated piping shall be designed and installed so as to prevent air lock.

EXCEPTION: If design considerations require the water pump to be mounted above the bottom of the water tank, it shall have an automatic priming system and provisions shall be made to prevent the loss of prime during intermittent pumping operations, particularly when the water level falls below the pump inlet level.

(4) Be constructed of materials that are compatible with water, water/foam solutions, and foam concentrate. If specified, a bronze water pump shall be supplied if local water conditions require additional protection from corrosive, acidic, or saltwater conditions.

d. The design, construction, and installation of the pump, pump drive system, and associated piping and controls shall—

(1) Allow the vehicle motive drive to be engaged while pumping operations are in progress without damage to or lurching of the vehicle.

(2) Permit the engagement of the pump at any engine and vehicle speed combination encountered during a normal vehicle operations profile.

(3) Allow pump engagement during vehicle operations, without engine stall and without causing more than a slight and momentary reduction in the engine speed, or damage to any of the components.

e. The manufacturer shall provide a means of automatically preventing the water pump and, if applicable, the foam pump from overheating while engaged and operating at zero discharge.

80. WATER RESERVOIR AND PIPING.

a. The water reservoir shall—

(1) Have a minimum rated capacity (working capacity) that meets the water quantity standard presented in Table 3, Performance Parameter 7.

(2) Be constructed of material suitable (i.e., stainless steel, bronze, brass or stainless steel flexible material) for service with the water intended to be used by the purchaser.

(3) Have sufficient longitudinal and transverse baffles with baffle openings that are not inline.

(4) Be equipped, for other than lifetime warranted tanks, with removable manhole covers, plates, or removable tops to permit access to the sump.

(5) Be fitted with a sump, complete with antiswirl baffles, a 2.5-inch (6.5 cm) main water tank drain and another low-point drain as required, an isolation valve, and a quarter-turn valve that has an accessible handle.

(6) Have a top-fill opening diameter of at least 8 inches (20 cm), a screen with maximum ¼-inch (6.4 mm) mesh, and a gasketed, latchable cap.

(7) Be vented to permit filling and overfilling at the rate specified in Paragraph 80.c and discharging in accordance with Table 3 without exceeding the design operating pressure or causing the reservoir to collapse. Overflow shall be directed to the ground.

(8) Have one 2.5-inch water tank fill connection with bleeder valve for Class 1 vehicles and one 4.5–inch tank fill connection with 4-inch plumbing valve with a 4.5-inch X 2.5-inch reducer with cap for Class 2 vehicles. The purchaser shall specify the size of thread connections.

b. The discharge piping shall be sized to allow sufficient water to the pump for the simultaneous operation of all turrets, ground sweeps, handlines, and undertruck nozzles, at the applicable discharge rates specified in Table 3.

c. Each connection and corresponding fill piping shall be sized to permit filling in no more than 2 minutes when the supply source provides sufficient volume at 80 psi (5.5 Bar) at the reservoir fill connection. If required, the capability of filling the water tank directly by drafting shall be provided.

CANCELLED

Section 5. Handlines, Reels, and Compartments.

81. HANDLINES.

a. There shall be a minimum of two handlines with nozzles for the discharge of water/foam that may be of the woven jacket or reeled type as specified by the purchaser. Reeled swing-out type hoses are acceptable, at the purchaser’s option. These handlines are to be located on either side (front or rear) or at the rear of the vehicle. If a complementary agent system is provided, the handline shall be “twinned” with one or both of the reeled water/foam handlines as specified by the purchaser. If a twin agent handline is specified for a dry chemical system, a nozzle that will entrain or capture dry chemical within the master stream of water agent flow may be provided if specified by the purchaser.

b. If selected by the purchaser, the reeled complementary and water/foam handlines shall—

(1) Be able to meet the discharge performance standard of Table 3, Performance Parameter 3, with the hose fully unrolled.

(2) Have at least 150 feet (45 m) of hose on each water/foam reel or each dedicated complementary agent reel. A complementary twinned agent reel shall have at least 100 feet (30 m) of hose.

(3) Be equipped with a variable pattern, pistol-grip shutoff-type nozzle that meets the discharge and pattern performance standard of Table 3, Performance Parameter 3, for both water and foam and be certified to meet NFPA 1964, Standard for Spray Nozzles and Tips.

(4) Electric rewind shall be provided for each hose reel.

c. If selected by the purchaser, the woven jacket water/foam handlines shall—

(1) Be able to meet the discharge performance standard of Table 3, Performance Parameter 4, with the hose fully stretched.

(2) Have at least 150 feet (45 m) of hose in each handline.

(3) Be equipped with a variable pattern, pistol-grip shutoff-type nozzle that meets the discharge and pattern performance standard of Table 3, Performance Parameter 4, for both water and foam and be certified to meet NFPA 1964.

(4) Meet the requirements of NFPA 1961, Standard for Fire Hose.

(5) Be stored and preconnected in a hose compartment.

NOTE: See the “NOTE” following Paragraph 110.d.(13) for a clarification of the handline test discharge rate conditions.

d. If selected by the purchaser, each preconnected handline shall be equipped with a system that will allow it to be advanced when the pump pressure is at minimum, where the pump rpm will advance only after the nozzle(s) is opened and return again to low rpm when flow is stopped for standby operation to prevent pump overheat and damage. This system shall not eliminate or override the normal pumping mode controls in the cab.

82. WOVEN JACKET HOSE AND REEL HOSE COMPARTMENTS.

a. Each woven jacket hose compartment shall—

(1) Have capacity for at least 150 feet (45 m) of 1.50-inch (38 mm) or 1.75-inch (44 mm) multiple jacket hose, as specified.

(2) Be fabricated from corrosion-resistant material and designed and constructed to drain by gravity.

(3) Be smooth and free from all projections that might damage the hose.

(4) Have no other equipment mounted or located where it will obstruct the removal of the hose.

(5) Be not more than 6 feet (1.8 m) above the ground unless installed on a reel.

(6) Have located in or adjacent to it a manually operated quarter-turn ball-type valve that controls the flow to each handline.

(7) Be weathertight and fitted with a closure that can be secured in either the open or closed position.

(8) Be stored on a roll out tray, which will maximize compartment storage space. The purchaser may also specify that the manufacturer provide an adjustable shelf with roll out tray in the upper part of

CANCELLED

2/18/02

each pre-connected hose compartment, above the stored hose.

b. Each hose reel shall—

(1) Be positioned to permit hose line removal by one person from any position in a 120-degree horizontal sector in front of the reel.

(2) Be equipped with a friction brake that will prevent the hose from unrolling when the vehicle is in motion.

(3) Be equipped with a power rewind with manual override.

AC 150/5220-10C

(4) Have located adjacent to it a manually operated, quarter-turn, ball-type valve that controls the flow to each handline.

c. Each hose reel compartment shall—

(1) Be provided with hose rollers on the left, right, and bottom edges of the reel compartment.

(2) Be weathertight and fitted with a closure that can be secured in either the open or closed position.

Section 6. Turrets, Man-rated Aerials, and Undertruck Nozzles.

83. PRIMARY TURRET. A primary turret can be either a roof or bumper turret.

a. One primary turret that meets the discharge and pattern standards of Table 3, Performance Parameter 5, shall be provided. It shall—

(1) Rotate at least 90 degrees to either side of center.

(2) Have a total traverse of at least 180 degrees.

(3) Elevate at least 45 degrees above the horizontal.

(4) Be capable of both high- and low-flow agent distribution and include a means of indicating to the driver/operator which flow rate is being distributed.

(5) Be fitted with nozzles that entrain or capture dry chemical application within the master stream of water agent flow if a dry chemical discharge from the primary turret is specified.

(6) Be operated with power-assist or as otherwise specified.

b. Roof-mounted turrets (optional flow) may have flow rates reduced by 200 gpm if the ground bumper turret flow rate is increased by the same amount.

c. Where the turret control is in the cab, operating forces shall be less than 30 pounds (13.5 kg).

A device to indicate turret azimuth and elevation shall be provided.

d. Turrets with a flow rate of 500 gpm (1.893 l/min) or more shall permit selection of either 50 percent or 100 percent of the rated turret discharge.

84. SECONDARY TURRET. A secondary turret can be either a roof or bumper turret. A power joystick controlled secondary turret shall be provided that meets the discharge and pattern standards of Table 3, Performance Parameter 6. It shall—

a. Have controls located in the cab within easy reach of the driver and a second crewmember.

b. Rotate 90 degrees to either side of center.

c. Have a total traverse of at least 180 degrees.

d. Elevate at least 45 degrees above the horizontal.

e. Be capable of automatic oscillation through a total traverse of at least 180 degrees with controls to adjust the oscillation angles, where specified by the purchaser.

85. HIGH-REACH EXTENDABLE TURRET– OPTION. There are many advantages to the highreach extendable turret. It allows firefighters to position their primary turret in an attack position, which will provide the most efficient use of agent. This position may range from ground level to a high-mounted engine or to the fuselage. The discharge of agent can begin while the vehicle is moving. A high-reach turret can be

CANCELLED

provided with penetrating nozzles as well as systems to discharge secondary agents.

a. If selected as the primary turret by the purchaser, the device provided shall—

(1) Meet the requirements of NFPA 1901, Standard for Automotive Fire Apparatus, latest edition. It shall achieve an 11-degree (20-percent) side slope with the extendable turret fully elevated and the nozzle rotated uphill at maximum horizontal rotation while discharging at maximum flow rate.

(2) Meet the functional requirements of Paragraph 84.a, b, and c for a conventional roof turret.

(3) Meet the primary water/foam agent turret discharge requirements of Table 3A, Performance Parameter 2, for high flow and Performance Parameter 3 for low flow, while in the bedded position.

(4) Meet the foam quality standards of Table 4 for the applicable foam applicator and foam type.

(5) Function during ARFF operations without the need for outriggers or other ground contact stabilizers that would render the vehicle immobile or hinder its maneuverability.

(6) Achieve the elevation and reach needed to service the highest tail-mounted engine for the type of aircraft specified by the purchaser and start application of agent within 30 seconds of activating the deployment cycle. The high-rise, telescoping, and/or articulating movement of the boom/tower shall be accomplished with not more than two adjacent lever controls and may be manual or automated, as specified by the purchaser, for preselected positioning of the elevation and reach. If automated, these functions shall be provided with a manual override positioning capability. All elevated and extendable turret should have an “auto-bed” feature.

(7) Be capable of applying agent to the upper level interior area of the most current wide body jet, height of 34 feet (10 m) from ground, with the vehicle positioned a horizontal distance of 20 feet (6 m) from the side of the aircraft so as not to impede evacuation or endanger the vehicle operator. In addition, the device must be capable of positioning the nozzle assembly at or near ground level at a minimum of 15 feet (4.5 m) in front of vehicle and be capable of applying an agent to the interior of the aircraft through cargo bay openings, passenger doorways, and emergency exits on the type

of aircraft, while the aircraft is in either the gear-up or gear-down landing position.

(8) Have a range of motion so as to permit positioning of the nozzle to direct a fire fighting agent stream at least 90 degrees to the longitudinal axis of the fuselage for interior fire extinguishment.

(9) Be capable of providing for horizontal movement of the boom along the aircraft of at least 30 degrees left and right of the vehicle centerline so as not to require repositioning or movement of the ARFF vehicle, including yellow flashing light to indicate to the operator when rotation exceeds 15 degrees. This horizontal rotation must be accomplished without the deployment of stabilizers or outriggers that might cause a delay in positioning or emergency movement of the rescue vehicle.

(10) Have sufficient backup systems to allow for override of the single-lever boom control and hydraulic system (or other power source) if the primary system becomes disabled.

(11) If the vehicle is provided with a dry chemical discharge, be fitted with nozzles that entrain or capture dry chemical application within the master stream of water agent flow if specified by the purchaser.

b. If specified by the purchaser as both a primary water/foam and a dry chemical turret (i.e., to function as a dual-agent turret system), the device shall meet the agent discharge performance of Table 3, Item 8.a, b, and c while in the bedded position.

c. For non-man-rated devices, the purchaser may specify either an adjustable or dual flow rate nozzle that will allow flow rates and patterns suitable for interior aircraft fire fighting.

d. Requirements for non-man-rated aerials (highreach turrets) have advantages during initial response where fast knockdown and penetration of the fuselage are critical to the mission. If a non-man-rated device is specified by the purchaser, it shall have the tools and devices needed for a driver or another operator to remotely perform the interior aircraft and tail-mounted engine fire fighting functions. The following are examples of such tools/devices:

(1) If specified, an auxiliary agent line capable of discharging either dry chemical or Clean Agent or approved equivalent through an appropriate nozzle while the device is extended out and up to its maximum operational reach. It shall meet the

CANCELLED

minimum auxiliary agent flow rate and pattern requirements of Table 3A.

(2) Remote optics capable of sufficient resolution to permit overall fire scene surveillance when fully extended and to provide the driver/operator with the detail needed for placement of the penetration device on the aircraft hull for proper piercing. The camera and associated lighting shall be designed and installed for exterior environmental operating conditions normally encountered by ARFF vehicles. A monitor (10 inches or larger) shall be cab-mounted in a road-worthy manner and readily accessible to the driver/operator.

(3) Skin penetrator/agent applicator—for penetration of the fuselage to access passenger cabin or cargo compartment fires from outside the aircraft. It shall be moveable in conjunction with the water/foam nozzle to allow proper placement with the nozzle control. It shall have a minimum flow requirement of 250 gpm (948 l/m).

(4) A roof window or observation window that allows the cab occupants to see the high-reach extendible turret device from their seated positions if the cab design precludes such observation. This window shall be transparent or lightly tinted to reduce glare. It shall not interfere with the range or operation of the high-reach extendible turret or any other existing components. The window shall be protected or guarded from damage by the operation or bedding of the high-reach device.

86. MAN-RATED AERIALS. For airports servicing wide-body aircraft, which have adequate garaging facilities and sufficient staffing, man-rated aerial devices provide certain abilities offered by no other ARFF apparatus. Man-rated aerials provide safe stable platforms for personnel and equipment during fire fighting operations and a means of gaining access to aircraft or high-mounted engines and other highmounted aircraft positions and systems.

a. If a man-rated device is specified by the purchaser, access and load ratings shall allow a properly equipped firefighter to use the tools and water/foam or auxiliary agent handlines necessary to perform the functions associated with interior aircraft fire fighting and fight tail-mounted engine fires from the fully extended device. Tip load rating shall be a minimum of 500 pounds (225 kg) as determined by NFPA 1901. If the device is equipped with a ladder attached to the boom or sections for continuous egress, it shall meet the requirements of NFPA 1901.

b. When specified by the purchaser, a man-rated aerial shall be equipped with adjustable or dual flow rate nozzle that will allow flow rates and patterns suitable for interior aircraft fire fighting. If provided, the nozzle shall be adjustable or dual flow rate at the manufacturer’s option.

c. If a man-rated aerial is specified by the purchaser, it shall meet the requirements of NFPA 1901.

87. DUAL AGENT TURRET. If a dual-agent turret is specified by the purchaser, it shall—

a. Meet the applicable discharge and pattern standards of Table 3, Performance Parameters 5 and 8.

b. Be capable of being depressed to discharge water/foam agent to within 30 feet (9 m) of the front bumper of the vehicle at full output using a dispersed stream.

c. If specified by the purchaser, a nozzle that entrains or captures dry chemical within the master stream of the water agent flow shall be provided.

88. UNDERTRUCK NOZZLES. If specified by the purchaser, a minimum of three (3) water/foam undertruck nozzles shall be provided so that the combined spray pattern will cover the total undertruck area as well as the inner sides of the wheels and tires.

CANCELLED

Section 7. Agent System Performance.

89. COMPLEMENTARY AGENT SYSTEM– OPTION.

a. If a dry chemical system is specified by the purchaser, it shall meet the standards of Table 3, Performance Parameter 1.

b. If a Clean Agent or approved equivalent substitute system is specified by the purchaser, it shall meet the standards of Table 3, Performance Parameter 2.

90. WATER/FOAM AGENT APPLICATORS.

a. Each water/foam agent handline shall be capable of delivering a finished foam solution that meets the applicable rate, range, and pattern standards of Table 3, Performance Parameters 3 or 4.

b. Each water/foam agent handline shall deliver finished foam of a quality that meets the applicable standards of Table 4.

c. Each water/foam agent turret shall be capable of delivering a finished foam solution that meets the applicable rate, range, and pattern standards of Table 3, Performance Parameters 5 or 6, as applicable.

d. Each water/foam agent turret shall deliver a finished foam of a quality that meets the applicable standards of Table 4.

All water/foam applicator performance requirements are based on the assumption that foam used to perform the tests is an approved foam concentrate; e.g., will pass the military AFFF foam specification 50 ft² fire test and the burnback resistance test.

91. THROUGH 99. RESERVED.

CANCELLED

Table 3. Extinguishing Agent System Performance Standards.

AGENT SYSTEM PERFORMANCE

AGENT SYSTEM PERFORMANCE

PARAMETER

VEHICLE CLASS

1 2

1. Dry Chemical Handline: a. Discharge Rate b. Range

> 5 lbs per sec < 7 lbs per sec

At least 25 feet

2. Clean Agent or Approved Equivalent Handline: a. Discharge Rate b. Range

> 5 lbs per sec < 7 lbs per sec

At least 25 feet

3. Reeled Water/Foam Handline: a. Nozzle Flow Rate: + 5% b. Straight Stream Pattern c. Dispersed Stream Pattern

VEHICLE CLASS

> 60 gpm (or 95gpm for 1.25-in. i.d. hose) > 50 ft reach > 20 ft reach and > 15 ft wide

4. Woven Jacket Water/Foam Handline: a. Nozzle Flow Rate: +5% b. Straight Stream Pattern c. Dispersed Stream Pattern

> 125 gpm or lower as specified > 65 ft reach > 20 ft reach and > 15 ft wide

5. Primary Turret Discharge: a. Flow Rate (gpm): (-0%, +10%) b. Stream Pattern/Distances:

750 1,200

(1) Straight/Far Point (ft) 190 250 (2) Dispersed/Far Point (ft) 65 75 (3) Dispersed/Width (ft) 35 35

6. Secondary Turret: a. Flow Rate (gpm): (-0%, +10%) b. Flat Patter Distances: (1) Near Point

(2) Width (ft) (3) Far Point (ft)

c. Straight Stream:

300 300

< Within 30 feet of front bumper

> 30 > 50

> 30 > 50

Range at least 150 feet

7. Water Tank: Minimum Rate Capacity (gal)

7. Water Tank: Minimum Rate Capacity (gal)

Percent Deliverable:

a. On level b. On 20% side slope c. On 30% ascending/descending grade

1,500 3,000 and above

100% 75% 75%

100% 75% 75%

8. Dry Chemical Turret Discharge: a. Flow Rate: b. Range, Far Point: c. Width:

> 16 lbs per second

> 100 ft

> 17 ft

CANCELLED

Table 3M. Extinguishing Agent System Performance Standards (Metric).

Continue reading ↓ 120 of 299 passages shown