Order 8900.2A General Aviation Airman Designee Handbook w/Change 3
This document is cancelled. Cancelled by 8900.2B. Check the official source before relying on it.
Sect › 3. When differences in guidance appear between this order and the…
Distribution: Electronic Only Initiated By: AFS-600
CHANGE
U.S. DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION 8900.2A CHG 2
National Policy Effective Date:
1/5/16
SUBJ: General Aviation Airman Designee Handbook
1. Purpose of This Order. This order provides mandatory standardized procedures and policy for those who administer aviation mechanic, parachute rigger, or pilot oral and practical tests, as well as issue Temporary Airman Certificates.
2. Audience. The primary audience is designees responsible for administering oral and practical tests and issuing Temporary Airman Certificates.
3. Where You Can Find This Order. You can find this order on the MyFAA employee Web site at https://employees.faa.gov/tools_resources/orders_notices. Inspectors can access this order through the Flight Standards Information Management System (FSIMS) at http://fsims.avs.faa.gov. Air carriers (operators) can find this order on the FAA’s Web site at http://fsims.faa.gov. This order is available to the public at http://www.faa.gov/regulations_policies/orders_notices.
4. Explanation of Policy Changes. This change:
• Restores content to Chapter 6, paragraph 26, Knowledge and Skill Elements for DPRE. • Updates for clarification, Figure 6-2P, Minimum Equipment and Tool List, in Chapter 6. • Clarifies in Chapter 7, paragraph 6 that references to Practical Test Standards (PTS) also apply to Airman Certification Standards (ACS). • Updates information regarding Flight Simulation Training Devices (FSTD) in Chapter 7, paragraph 12. • Removes AFS-800 from the Airman Certification Representative (ACR) selection process in Chapter 7, paragraph 118. • Revises flight instructor refresher ‘clinic’ to ‘course’ (FIRC) and ‘sponsor’ to ‘provider’.
5. Disposition of Transmittal Paragraph. This change will remain in FSIMS until superseded by a revision to this order.
Sect › Director, Flight Standards Service
1/5/16 8900.2A CHG 2
PAGE CHANGE CONTROL CHART
Remove Pages Dated Insert Pages Dated
Pages iii thru v 3/31/15 Pages iii thru v 1/5/16
Pages viii thru x 3/31/15 Pages viii thru x 1/5/16
Page 1-5 3/31/15 Page 1-5 1/5/16
Pages 6-21 3/31/15 Pages 6-21 and 6-22 1/5/16
Pages 6-61 thru 6-70 3/31/15 Pages 6-62 thru 6-69 1/5/16
Page 7-8 3/31/15 Page 7-8 1/5/16
Page 7-12 3/31/15 Page 7-12 1/5/16
Page 7-23 3/31/15 Page 7-23 1/5/16
Pages 7-133 thru 7-135 3/31/15 Pages 7-133 thru 7-135 1/5/16
Page A-1 3/31/15 Page A-1 1/5/16
John S. Duncan Director, Flight Standards Service John S. Duncan's signature
Distribution: Electronic Only Initiated By: AFS-600
CHANGE
U.S. DEPARTMENT OF TRANSPORTATION 8900.2A CHG 1 FEDERAL AVIATION ADMINISTRATION
National Policy Effective Date:
6/12/15
SUBJ: General Aviation Airman Designee Handbook
1. Purpose of This Order. This order provides mandatory standardized procedures and policy for those who administer aviation mechanic, parachute rigger, or pilot oral and practical tests, as well as issue Temporary Airman Certificates.
2. Audience. The primary audience is designees responsible for administering oral and practical tests and issuing Temporary Airman Certificates.
3. Where You Can Find This Order. You can find this order on the MyFAA employee Web site at https://employees.faa.gov/tools_resources/orders_notices. Inspectors can access this order through the Flight Standards Information Management System (FSIMS) at http://fsims.avs.faa.gov. Air carriers (operators) can find this order on the FAA’s Web site at http://fsims.faa.gov. This order is available to the public at http://www.faa.gov/regulations_policies/orders_notices.
4. Explanation of Policy Changes. This change restores the original content of the recurrent training interval table in Chapter 3, paragraph 3.
5. Disposition of Transmittal Paragraph. This change will remain in FSIMS until superseded by a revision to this order.
PAGE CHANGE CONTROL CHART
Remove Pages Dated Insert Pages Dated
Page iii 3/31/15 Page iii 6/12/15
Page 3-2 thru 3-3 3/31/15 Page 3-2 thru 3-3 6/12/15
John Barbagallo Deputy Director, Flight Standards Service
U.S. DEPARTMENT OF TRANSPORTATION ORDER FEDERAL AVIATION ADMINISTRATION 8900.2A National Policy
Effective Date:
3/31/15
SUBJ: General Aviation Airman Designee Handbook
1. In 2006, Aviation Safety (AVS) published Federal Aviation Administration (FAA) Order VS 1100.2, Managing AVS Delegation Programs, which provided direction for the management and oversight of AVS delegation programs, including Flight Standards Service (AFS) designees. During the next 2 years, the AVS Delegation Steering Group, which included representation from AFS, identified important goals including the integration of AFS designee policy. An AFS working group, including policy holders for each General Aviation (GA) airman designee type, was formed to work on this consolidated order. This order contains integrated procedures for the selection, appointment, oversight, training, renewal, termination, and appeal of AFS GA airman designees in accordance with Order VS 1100.2.
2. This order contains procedures for authorized GA airman designees and inspectors to conduct certificate holder oral and practical tests and issue Temporary Airman Certificates.
3. When differences in guidance appear between this order and the current edition of FAA Order 8900.1, Flight Standards Information Management System (FSIMS), Volume 13, Flight Standards Designees, use the document with the most current revision date. This order also applies to all aviation safety inspectors (ASI) (referred to in this order as ASIs or inspectors) who review and approve airman application and testing files for GA airman designees.
John S. Duncan Director, Flight Standards Service
Distribution: Electronic Only Initiated By: AFS-600
Sect › 6. Aviation Mechanic Tests … 6-3
1/5/16 8900.2A CHG 2
iii
Table of Contents
Paragraph Page
Chapter 1. General Information
1. Purpose of This Order … 1-1 2. Audience … 1-1 3. Where You Can Find This Order … 1-1 4. What This Order Cancels … 1-1 5. Explanation of Policy Changes … 1-2 6. Delegation/Rescission of a Designee Authorization … 1-2 7. Role of the Designee … 1-2 8. Definitions … 1-3 9. Office Information and Points of Contact (POC) … 1-5
Chapter 2. Selection and Appointment
1. Selection … 2-1 2. Appointment … 2-3 3. General Eligibility Requirements … 2-4
Chapter 3. Oversight, Training, and Renewal
1. Oversight … 3-1 2. Initial Training Seminar … 3-1 3. Recurrent Training … 3-2 4. Expiration … 3-3 5. Renewal … 3-3 6. Knowledge and Skill … 3-4
Chapter 4. Termination and Appeal
1. Termination … 4-1 2. Types of Termination … 4-1 3. Termination Letter … 4-1 4. Appeal … 4-1
Chapter 5. Privileges, Limitations, and Responsibilities
1. Privileges … 5-1 2. Limitations … 5-2 3. Responsibilities … 5-3
Chapter 6. Designated Mechanic Examiner (DME) and Designated Parachute Rigger
Examiner (DPRE) Program Section 1. DME—General … 6-1
1. Additional Requirements for Appointment … 6-1 2. DME Designations Issued … 6-2 3. Designee Materials … 6-2 4. Security … 6-3 5. FAA Certification Policy … 6-3 6. Aviation Mechanic Tests … 6-3
1/5/16 8900.2A CHG 2
iv
Table of Contents (Continued)
Sect › 5. Designee COA Letters … 7-10
Paragraph Page
Section 2. DME—Conducting and Grading Tests … 6-4
7. Preparation: Conduct a Pretest Interview … 6-4 8. Knowledge and Skill Elements for DME … 6-5 9. Applicant Eligibility … 6-6 10. Conducting the Tests … 6-8 11. Evaluating Applicant Performance … 6-10 12. Recording the Results of Tests … 6-12 13. When the Applicant Passes … 6-12 14. Applicants Under 18 Years of Age … 6-14 15. When the Applicant Fails … 6-14 16. Issuance of FAA Form 8060-4 by a DME When Oral and Practical Tests are Not Administered … 6-15 17. Reconstruction of a Lost Certification File … 6-16 18. Disposition of Files … 6-16
Section 3. DPRE—General Information … 6-18
19. Additional Requirements for Appointment … 6-18 20. DPRE Designations Issued … 6-19 21. Designee Materials … 6-19 22. Security … 6-19 23. FAA Certification Policy … 6-20 24. Parachute Rigger Tests … 6-20
Section 4. DPRE—Conducting and Grading Tests … 6-20
25. Preparation: Conduct a Pretest Interview … 6-20 26. Knowledge and Skill Elements for DPRE … 6-21 27. Applicant Eligibility … 6-23 28. Conducting the Tests … 6-25 29. Evaluating Applicant Performance … 6-26 30. Recording the Results of Tests … 6-28 31. When the Applicant Passes … 6-28 32. Applicants Under 18 Years of Age … 6-29 33. When the Applicant Fails … 6-30 34. Issuance of FAA Form 8060-4 by a DPRE When Oral and Practical Tests are Not Administered … 6-31 35. Reconstruction of a Lost Certification File … 6-32 36. Disposition of Files … 6-32
Chapter 7. Designated Pilot Examiner (DPE) Program
Section 1. General … 7-1
1. Additional Qualifications … 7-1 2. Specific Eligibility Requirements … 7-3 3. Types of Designation … 7-7 4. Additional Designations … 7-9 5. Designee COA Letters … 7-10
Sect › 42. Instrument Flying Skills—Partial Panel … 7-48
1/5/16 8900.2A CHG 2
v
Table of Contents (Continued)
Paragraph Page
Section 2. Conduct Practical Test/Certification Functions … 7-12
6. General … 7-12 7. Testing Applicants Trained by the Designee … 7-16 8. Designee Limitations … 7-17 9. Status of Designees During Practical Tests … 7-17 10. Aircraft Used for Practical Tests … 7-20 11. Aircraft Equipment … 7-22 12. Flight Simulation Training Devices (FSTD) … 7-23 13. Engine Shutdown on Multiengine Airplanes During the Practical Test … 7-23 14. Structure of the Practical Test … 7-24 15. Practical Test Discontinuance … 7-25 16. Repeating Maneuvers on Practical Tests … 7-26 17. Practical Test Briefings … 7-26 18. Segmented Practical Tests (Planned) … 7-27 19. Retest in Event of Failure … 7-27 20. Accidents and Incidents During Practical Tests … 7-28 21. PTS … 7-28 22. Prerequisites for Practical Tests … 7-28 23. Verification of an Applicant’s Identity … 7-33 24. Illegal Substance Conviction … 7-33 25. Completion of FAA Form 8710-1 … 7-33 26. Preparation of the Certification File … 7-34 27. Review of an Designee’s Decision … 7-35 28. Issuance of FAA Form 8060-4 … 7-35 29. Limitations … 7-36 30. Issuance of FAA Form 8060-5 … 7-37 31. Part 141 Stage Checks … 7-38 32. Blue Seal Certificates … 7-38 33. Flight and Duty Time as a DPE … 7-38 34. Procedures … 7-39
Section 3. Issue a Student Pilot Certificate … 7-43
35. General … 7-43 36. Nonrenewable … 7-44 37. Procedures … 7-44
Section 4. Special Emphasis Items … 7-47
38. Special Emphasis Items … 7-47 39. Dangers Associated with Simulation of Power Failure in Single-Engine Airplanes by the Interruption of Fuel Flow … 7-47 40. Pilot External Vigilance (Scan Program) … 7-47 41. Accurate Position Reporting and Collision Avoidance … 7-48 42. Instrument Flying Skills—Partial Panel … 7-48
Sect › 72. General … 7-77
vi
Table of Contents (Continued)
Paragraph Page
Section 5. Flight Reviews and Competency Checks … 7-49
43. Flight Reviews and Competency Checks … 7-49 44. Designee or Inspector Participation … 7-49 45. Application for a Flight Review or Competency Check … 7-49 46. Combining Flight Reviews and Competency Checks … 7-49 47. Evaluating the Flight Review … 7-50 48. Length of Review … 7-50 49. Logbook Endorsements … 7-50 50. Recent Instrument Experience under § 61.57 … 7-51 51. High Performance Airplane Check under § 61.31(f) … 7-52 52. Complex Airplane Check under § 61.31(e) … 7-52 53. Self-Launching or Powered Sailplane Flight Checks … 7-52 54. Night Vision Goggles (NVG) Training, Endorsement, and Qualification for Pilots and Flight Instructors … 7-52
Section 6. Conduct a Recreational Pilot Certification, Including Additional
Category/Class Ratings at the Recreational Pilot Certification Level … 7-55 55. General … 7-55 56. Additional Category and Class Ratings … 7-57 57. Upgrading to a Private Pilot Certificate … 7-57 58. Procedures … 7-58
Section 7. Conduct a Sport Pilot Certification … 7-62
59. General … 7-62 60. Procedures … 7-63
Section 8. Conduct a Private Pilot Certification, Including Additional Category/Class
Ratings at the Private Pilot Certification Level … 7-66 61. General … 7-66 62. Eligibility Requirements … 7-66 63. Limitations … 7-68 64. Categories and Classes … 7-69 65. Recreational Pilot Upgrades … 7-69
Section 9. Conduct a Commerical Pilot Certification, Including Additional
Category/Class Ratings at the Commerical Pilot Certification Level … 7-70 66. General … 7-70 67. Eligibility Requirements … 7-70 68. Categories and Classes … 7-72 69. Instructor Privileges in Lighter-than-Air Aircraft … 7-73 70. Complex Airplane Requirements … 7-73 71. Procedures … 7-73
Section 10. Conduct an Airline Transport Pilot Certification, Including Additional
Category/Class Ratings at the Airline Transport Certification Level … 7-77 72. General … 7-77
Sect › 101. Denial of Renewal or Reinstatement … 7-122
vii
Table of Contents (Continued)
Paragraph Page
Section 11. Conduct an Instrument Rating Certification … 7-78
73. General … 7-78 74. Eligibility Requirements … 7-79 75. Types of Instrument Ratings Issued … 7-80 76. Flight Controls … 7-80 77. Use of Nonapproved Instrument Approach Procedures (IAP) … 7-80 78. Limitations … 7-80 79. Procedures … 7-81
Section 12. Conduct a Pilot Type Rating Certification … 7-85
80. General … 7-85 81. Pilot Type Rating That May Be Performed as Either a Single Pilot or With an SIC .... 7-87 82. Procedures … 7-98
Section 13. Procedures for Issuing a Second-in-Command Pilot Type Rating … 7-102
83. General … 7-102
Section 14. Conduct a Private Pilot Certification for Weight Shift Control and Powered
Parachute, Including Additional Category/Class Ratings at the Private Pilot Certification Level … 7-102 84. General … 7-102 85. Eligibility Requirements … 7-102 86. Limitations … 7-104 87. Categories and Classes … 7-104 88. Procedures … 7-105
Section 15. Conduct a Flight Instructor with a Sport Pilot Rating Practical Test for an
Initial, Renewal, or Reinstatement … 7-109 89. General … 7-109 90. General Procedures Initial Certification … 7-109 91. General Procedures for Renewal or Reinstatement … 7-111 92. Denial of Renewal or Reinstatement … 7-111 93. Gold Seal Flight Instructor Certificates … 7-112 94. Category and Class Privileges for a Flight Instructor Certificate with a Sport Pilot Rating … 7-112 95. Procedures … 7-113
Section 16. Conduct a Flight Instructor Practical Test for an Initial, Renewal,
Reinstatement Certification, or an Additional Category/Class Rating to a Flight Instructor Certificate … 7-116 96. General … 7-116 97. Knowledge Test … 7-118 98. Practical Test … 7-118 99. Eligibility Requirements … 7-119 100. General Procedures for Renewal or Reinstatement … 7-121 101. Denial of Renewal or Reinstatement … 7-122
Sect › 128. Procedures … 7-158
1/5/16 8900.2A CHG 2
viii
Table of Contents (Continued)
Paragraph Page
102. Gold Seal Flight Instructor Certificates … 7-122 103. Category, Class, and Instrument Ratings Placed on a Flight Instructor Certificate .. 7-123 104. Limitations … 7-123 105. Procedures … 7-123
Section 17. Conduct Pilot Proficiency Checks as a Pilot Proficiency Examiner … 7-128
106. General … 7-128 107. Limitations … 7-128 108. Experience Requirements for Designation as a PPE … 7-129 109. Practical Test … 7-130 110. COA Letter … 7-130 111. Additional Designations … 7-130 112. PIC Proficiency Check Procedures … 7-130 113. Proficiency Check Records … 7-131
Section 18. Accomplish Designation/Issue Certificates as an ACR, Limited to
Examining Authority under Part 141 … 7-131 114. General … 7-131 115. Selection of ACRs … 7-132 116. Certification of Graduates … 7-133
Section 19. Accomplish Designation/Issue Certificates as an ACR Employed Solely by
an FIRC Provider … 7-133 117. General … 7-133 118. Selection of ACRs … 7-134 119. Flight Instructor Certificate and Ratings Issued on the Basis of Military Competence by an MCE … 7-135 120. Certification of Graduates … 7-138
Section 20. Accomplish Designation/Conduct Functions as an MCE, FPE, GIE,
and FIRE … 7-139 121. Background … 7-139 122. General Information for MCE and FPE Designations … 7-140 123. Pilot Certificates and Ratings Issued on the Basis of Military Competence by an MCE … 7-143 124. Compliance with Other Provisions … 7-144 125. Designation of an FIRE … 7-144 126. Designation of a GIE … 7-145
Section 21. Accomplish Issuance of a U.S. Pilot Certificate Based on a Foreign Pilot
License … 7-146 127. General Information … 7-146 128. Procedures … 7-158
Sect › 6-2L. FAA Form 8060-4, Temporary Airman Certificate … 6-59
1/5/16 8900.2A CHG 2
ix
Table of Contents (Continued)
Paragraph Page
Section 22. IACRA Process … 7-163
129. General … 7-163 130. Procedures … 7-163
Chapter 8. Adminstrative Information
1. Distribution … 8-1 2. Deviations … 8-1 3. Suggestions or Comments … 8-1
Appendix A. Acronyms and Abbreviations … A-1
Appendix B. Directive Feedback Information … B-1
List of Figures
Figure Page
6-1. Instructions for Completing FAA Form 8610-2, Airman Certificate and/or Rating Application … 6-33 1. Procedures for Completing FAA Form 8610-2 … 6-33 2. Privacy Act … 6-34 3. Complete the Top Section … 6-35 4. Block I—Applicant Information … 6-35 5. Block II—Certificate or Rating Applied for On Basis of— … 6-39 6. Block III—Record of Experience … 6-41 7. Block IV—Applicant’s Certification … 6-43 8. Block V—I Find This Applicant Meets the Experience Requirements of 14 CFR Part 65 and is Eligible to Take the Required Tests … 6-44 9. For FAA Use Only … 6-45 10. Results of Oral and Practical Tests … 6-45 11. Designated Examiner’s Report … 6-46 12. Applicant’s Certification … 6-46 13. FAA Inspector’s Report … 6-47 6-2A. FAA Form 8610-2, Airman Certificate and/or Rating Application … 6-48 6-2B. FAA Form 8610-2, Airman Certificate and/or Rating Application … 6-49 6-2C. Attachment for FAA Form 8610-2, Airman Certificate and/or Rating Application .... 6-50 6-2D. FAA Form 8610-2, Airman Certificate and/or Rating Application … 6-51 6-2E.
FAA Form 8610-2, Airman Certificate and/or Rating Application … 6-52 6-2F. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) .... 6-53 6-2G. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) .... 6-54 6-2H. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) .... 6-55 6-2I. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) .... 6-56 6-2J. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) .... 6-57 6-2K. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) .... 6-58 6-2L. FAA Form 8060-4, Temporary Airman Certificate … 6-59
Sect › 7-14A.
1/5/16 8900.2A CHG 2
x
List of Figures (Continued)
Figure Page
6-2M. FAA Form 8060-4, Temporary Airman Certificate … 6-60 6-2N. Example Statement of Additional Instructions … 6-60 6-2O. Airman Computer Test Report for Aviation Mechanic Airframe (AMA) … 6-61 6-2P. Minimum Tool and Equipment List … 6-62 6-3A. FAA Form 8610-2, Airman Certificate and/or Rating Application … 6-70 6-3B. FAA Form 8610-2, Airman Certificate and/or Rating Application (Front Side) … 6-71 6-3C. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) .... 6-72 6-3D. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) .... 6-73 6-3E. FAA Form 8610-2, Airman Certificate and/or Rating Application (Reverse Side) .... 6-74 6-3F. Example Statement of Additional Instruction … 6-75 6-3G. Airman Computer Test for Parachute Rigger … 6-76 6-3H. FAA Form 8060-4, Temporary Airman Certificate … 6-77 6-3I. FAA Form 8060-4, Temporary Airman Certificate … 6-78 6-3J. FAA Form 8060-4, Temporary Airman Certificate … 6-79 6-4A. Airframe and Powerplant Mechanic Oral and Practical Planning Sheet (Front Side) … 6-80 6-4B.
Airframe and Powerplant Mechanic Oral and Practical Planning Sheet (Reverse Side) … 6-81 6-4C. Parachute Rigger Oral/Practical Test Planning Sheet … 6-82 7-1. Experience Required for Initial Designation as a Sport Pilot Examiner … 7-4 7-2A. Experience Required for Initial Designation as Private Pilot Examiner … 7-5 7-2B. Experience Required for Initial Designation as Commercial Pilot Examiner … 7-5 7-3A. Experience Required for Initial Designation as a Commercial and Instrument Rating Examiner … 7-6 7-3B. Experience Required for Initial Designation as an Airline Transport Pilot Examiner … 7-6 7-4. Recent Pilot-in-Command Experience Required … 7-7 7-5. Vintage Airplane Groups … 7-12 7-6. ICAO Level 4 English Language Proficiency Criteria … 7-165 7-7. Sample FAA Form 8410-1, Airman Proficiency/Qualification Check … 7-166 7-8A. Pilot Examiner Test Guide … 7-167 7-8B. Sport Pilot Examiner Test Guide … 7-171 7-9A. Sample Letter of Discontinuance (Pilot) … 7-175 7-9B. Sample Letter of Discontinuance (Sport Pilot) … 7-176 7-10. Airman Knowledge Test Report … 7-177 7-10A.
Airman Knowledge Test Report … 7-178 7-11. Letter from Part 141 School with Knowledge Test Examining Authority … 7-179 7-12. Sample Transporation Security Administration Approval Letter … 7-180 7-13. FAA Form 8710-1, Airman Certificate and/or Rating Application (Front) … 7-181 7-13A. FAA Form 8710-1, Airman Certificate and/or Rating Application (Back) … 7-182 7-14. Sample of FAA Form 8710-11, Airman Certificate and/or Rating Application—Sport Pilot (Front Side) … 7-183 7-14A. Sample of FAA Form 8710-11, Airman Certificate and/or Rating Application—Sport Pilot (Reverse Side) … 7-184
Sect › 7-32. Verification of Authenticity Form and Instructions … 7-204
xi
List of Figures (Continued)
Figure Page
7-15. Sample FAA Form 8060-4, Temporary Airman Certificate (Pilot) … 7-185 7-15A. Sample FAA Form 8060-4, Temporary Airman Certificate (Sport Pilot) … 7-186 7-16. Center Thrust Limitation … 7-187 7-17. Sample FAA Form 8060-5, Notice of Disapproval of Application (Pilot) … 7-188 7-17A. Sample FAA Form 8060-5, Notice of Disapproval of Application (Sport Pilot) … 7-189 7-18. Sample Application for a Part 141 Stage Check … 7-190 7-19. Sample FAA Form 8420-2, Medical Certificate____ Class and Student Pilot Certificate … 7-191 7-20. Sample Student Pilot Certificate … 7-192 7-21. Sample Recreational Pilot Certificate … 7-193 7-22. Sample Private Pilot Certificate with Recreational Pilot Category Privileges … 7-194 7-23. Sample Commercial Pilot Certificate … 7-195 7-24. Sample ATP Certificate with Instrument Privileges Shown … 7-196 7-25. Sample Second-in-Command Limitation … 7-197 7-26. Sample SIC Pilot Type Rating Temporary Airman Certificate … 7-198 7-27. Sample SIC Pilot Type Rating Application for Graduates of Approved Training Programs (Parts 141/142) … 7-199 7-28. Sample SIC Pilot Type Rating Application for Graduates of Approved Training Programs (Parts 135/121) … 7-200 7-29. Sample SIC Pilot Type Rating Application for § 61.55 Applicants … 7-201 7-30. SIC Pilot Type Rating Application Completed by an Authorized Designated Examiner or an APD … 7-202 7-31. Sample Gold Seal Flight Instructor Certificate (Pilot) … 7-203 7-31A. Sample Gold Seal Flight Instructor Certificate with a Sport Pilot Rating … 7-204 7-32. Verification of Authenticity Form and Instructions … 7-204
Note › Note
Chapter 1. General Information
1. Purpose of This Order.
a. Mandatory Standardized Procedures and Policy. This order provides mandatory standardized procedures and policy for those who administer aviation mechanic, parachute rigger, or pilot oral and practical tests, as well as issue Temporary Airman Certificates. It also emphasizes the importance of the designee’s knowledge of administering oral and practical tests. Compliance with these mandatory procedures ensures that airman applicants meet a satisfactory level of competence and workmanship required for certification. This order does not relieve Federal Aviation Administration (FAA) personnel from instructing and providing guidance to designees.
b. Types of General Aviation (GA) Airman Designees Covered in This Order. Throughout this order, Technical Personnel Examiner (TPE) references will refer to Designated Mechanic Examiners (DME) and Designated Parachute Rigger Examiners (DPRE) collectively. When necessary, DMEs and/or DPREs may be specifically identified if applicable only to that designee type. For the purposes of this order, Designated Pilot Examiners (DPE) will refer to Private Pilot Examiners (PE), Commercial and Instrument Rating Examiners (CIRE), Commercial Pilot Examiners (CE), Airline Transport Pilot Examiners (ATPE), Flight Instructor Examiners (FIE), National Designated Pilot Examiners, Flight Engineer Examiners (NDPE/FEE), Sport Pilot Examiners (SPE), Sport Pilot Flight Instructor Examiners (SFIE), and Pilot Proficiency Examiners (PPE), as well as pilot examiners with administrative privileges only including: Airman Certification Representatives (ACR), Flight Instructor Renewal Examiners (FIRE), Foreign Pilot Examiners (FPE), Ground Instructor Examiners (GIE), and Military Competency Examiners (MCE).
Note: This order does not apply to check airmen/check pilots and Aircrew Designated Examiners (ADE) serving in programs approved under Title 14 of the Code of Federal Regulations (14 CFR) parts 91 subpart K (part 91K), 121, 125, and 135. It also does not apply to Training Center Evaluators (TCE) who serve at training centers certificated under 14 CFR part 142.
2. Audience. The primary audience is designees responsible for administering oral and practical tests and issuing Temporary Airman Certificates.
3. Where You Can Find This Order. You can find this order on the MyFAA employee Web site at https://employees.faa.gov/tools_resources/orders_notices. Inspectors can access this order through the Flight Standards Information Management System (FSIMS) at http://fsims.avs.faa.gov. Air carriers (operators) can find this order on the Federal Aviation Administration’s (FAA) Web site at http://fsims.faa.gov. This order is available to the public at http://www.faa.gov/regulations_policies/orders_notices.
4. What This Order Cancels. This order cancels FAA Order 8900.2, General Aviation Airman Designee Handbook, dated September 30, 2008.
Note: Implementation procedures for the new PTS and test generator (for DMEs): Both the current PTS and the new test generator procedures will be in
Sect › 7. Role of the Designee.
effect until 6 months after the effective date of this order, at which time, all tests must be administered under the new PTS and test generator guidelines. Newly appointed DMEs must use the new PTS/test generator upon completion of initial training.
5. Explanation of Policy Changes. This revision incorporates updated information, procedural and policy changes, and new guidance. These changes include the following:
a. Certificate of Authority (COA) Letter. FAA Form 8430-9, Certificate of Authority, and letters of authorization (LOA) are no longer issued. In this revision, all previous references to an LOA are now referred to as a COA. See Chapter 7, Section 1, paragraph 5 for further information.
b. Test Observation. This revision changes how the designee will conduct their first test. This revision also changes DME appointment requirements. See Chapter 6, Section 1, subparagraph 1a(3).
c. Conducting and Grading Tests. This revision changes how the designee will notify the FAA, and also changes how practical tests are developed. See Chapter 6, Section 2, paragraph 10.
d. Original FAA Form 8610-2. This revision changes requirements for an applicant’s graduation or completion certificate from an AMTS. See Chapter 6, Section 2, subparagraph 9d(2)(a).
e. Conducting Practical Tests. This revision requires the designee to notify the FAA before testing. See Chapter 7, Section 2, paragraph 6.
f. Procedures for Issuing a Second-in-Command (SIC) Pilot Type Rating. This revision refers the designee to FAA Order 8900.1, Flight Standards Information Management System (FSIMS), Volume 5, Chapter 2, Section 5 for completing the certification function.
g. Flight Simulation Training Devices (FSTD). This revision changes requirements for FSTDs, personal computer-based aviation training devices (PCATD), basic aviation training devices (BATD), and advanced aviation training devices (AATD). See Chapter 7, Section 2, paragraph 12.
h. Verification of an Applicant’s Identity. This revision adds Transportation Security Administration (TSA) requirements for foreign nationals. See Chapter 7, Section 2, paragraph 23.
6. Delegation/Rescission of a Designee Authorization. Title 49 of the United States Code (49 U.S.C.) § 44702 empowers the FAA Administrator to delegate to private individuals any function relating to the examination, inspection, and testing of airman applicants.
7. Role of the Designee. Designees have been an important part of the FAA’s support to the flying public for over 60 years. During that time, designees successfully completed thousands of certification activities on the FAA’s behalf. The designee function is vital to enhancing the
Sect › h. Designated Pilot Examiner (DPE). A DPE is an individual, appointed…
FAA’s public service role and enhancing overall safety in the National Airspace System (NAS). The FAA and its designees are in a symbiotic relationship. The FAA appoints designees to leverage its workforce and provide certification services to the public, and the designee provides certification services to the public in accordance with FAA policy and guidance. One component of this relationship involves how the FAA views the designee, as well as how the designee views the FAA.
8. Definitions. This paragraph contains definitions for FAA forms and terms commonly used in this order. Appendix A contains a list of acronyms used in this order.
a. Airman Medical Certificate. An airman medical certificate is a valid certificate issued under 14 CFR part 67, Medical Standards and Certification.
b. Aviation Maintenance Technician School (AMTS). An FAA-approved school for aviation mechanics. Graduation from the appropriate course of a certificated AMTS is one way for mechanic applicants to meet the experience requirement.
c. Aviation Safety Inspector (ASI). An FAA employee with the necessary technical qualifications who is responsible for developing, administering, investigating, and enforcing safety regulations for airmen, aircraft, and aircraft operations. In most cases, ASIs are also responsible for the oversight of designees.
d. Aviation Safety Technician (AST). An FAA employee who provides technical support and assistance to ASIs.
e. COA Letter. A COA letter is issued to each Flight Standards GA designee to specify their authority and appropriate limitations for a given appointment period.
Note: FAA Form 8430-9 and LOAs are no longer issued, but may remain in effect until expiration, unless surrendered or terminated before that time.
f. Designated Mechanic Examiner (DME). A DME is an individual, appointed in accordance with 14 CFR part 183, § 183.25, who holds a valid aviation mechanic certificate, possesses technical knowledge and experience required for aviation mechanic certification, and meets the general qualification requirements set forth in Chapter 2 and the DME-specific qualifications set forth in Chapter 6 of this order.
g. Designated Parachute Rigger Examiner (DPRE). A DPRE is an individual, appointed in accordance with § 183.25, who has a high level of knowledge in the subject areas required for parachute rigger certification, holds a master parachute rigger certificate for the particular designation, and meets the general qualification requirements in Chapter 2, and the DPRE-specific qualifications set forth in Chapter 6 of this order.
h. Designated Pilot Examiner (DPE). A DPE is an individual, appointed in accordance with § 183.23, who meets the general qualification requirements in Chapter 2 and the DPE-specific qualifications in Chapter 7. For the purposes of this order, a DPE is a PE, CIRE, CE, ATPE, FIE, PPE, NDPE/FEE, SPE, or SFIE. It also includes designees with administrative privileges only: ACR, FIRE, FPE, GIE, and MCE.
Sect › t. FAA Form 8710-12, Light-Sport Standardization Board-Designated Pilot…
i. Designee. Designee is the general term used in this order to describe a representative of the FAA Administrator authorized by law and appointed in accordance with the applicable provisions of § 44702 or part 183, Representatives of the Administrator, to examine, test, and/or make inspections necessary to issue airman or aircraft certificates. For the purposes of this order, designee refers to individual examiner designations, including TPEs and DPEs.
j. FAA Form 8000-5, Certificate of Designation. FAA Form 8000-5 is a certificate issued to a designee by the managing FAA office authorizing the designee privileges. Throughout this order, it is referenced as FAA Form 8000-5.
k. FAA Form 8060-4, Temporary Airman Certificate. FAA Form 8060-4 is a Temporary Airman Certificate issued to a successful airman applicant.
l. FAA Form 8060-5, Notice of Disapproval of Application. FAA Form 8060-5 is issued by a DPE to an unsuccessful airman applicant.
m. FAA Form 8110-28, Application and Statement of Qualification (DME/DPRE/Designated Airworthiness Representative-Maintenance (DAR-T). FAA Form 8110-28 is the application used by DME/DPRE applicants for appointment and renewal.
n. FAA Form 8420-2, Medical Certificate … Class and Student Pilot Certificate. FAA Form 8420-2 is issued to an airman applicant who meets the requirements for a Student Pilot Certificate by an Aviation Medical Examiner (AME) and serves as both a medical certificate and a Student Pilot Certificate.
o. FAA Form 8610-2, Airman Certificate and/or Rating Application. FAA Form 8610-2 is used by mechanic and parachute rigger applicants when applying for an airman certificate and/or rating.
p. FAA Form 8710-1, Airman Certificate and/or Rating Application. FAA Form 8710-1 is used by pilot applicants (other than sport pilot applicants) when applying for an airman certificate and/or rating.
q. FAA Form 8710-2, Student Pilot Certificate. FAA Form 8710-2 is issued to a qualified student pilot applicant.
r. FAA Form 8710-10, Designated Pilot Examiner Application. FAA Form 8710-10 is the application used by DPE applicants (other than SPE/SFIE applicants) to submit to the National Examiner Board (NEB) or managing FAA office, as applicable.
s. FAA Form 8710-11, Airman Certificate and/or Rating Application – Sport Pilot. FAA Form 8710-11 is used by sport pilot applicants when applying for an airman certificate and/or rating.
t. FAA Form 8710-12, Light-Sport Standardization Board-Designated Pilot Examiner Candidate Application. FAA Form 8710-12 is the application used by SPE/SFIE applicants to submit to the NEB.
Sect › d. Experimental Aircraft Association (EAA). The EAA is an international…
1/5/16 8900.2A CHG 2
u. Minimum Tool and Equipment List. Tools and equipment necessary to administer the General, Airframe, & Powerplant practical tests. See Figure 6-2P.
v. Flight Instructor Refresher Course (FIRC). FIRCs provide a method by which instructors can renew their instructor certificates.
w. Integrated Airman Certification and/or Rating Application (IACRA). The IACRA system is an Internet-based (paperless) method of processing airman applications.
x. Managing FAA Office. The managing FAA office refers to the geographically assigned office responsible for managing and providing oversight for designees. Previous references to Flight Standards District Office (FSDO) and International Field Office (IFO) are now referenced as the managing FAA office.
y. Pilot’s Bill of Rights (PBR). See FAA Order 8900.1, Volume 5, Chapter 5, Section 2 for details on PBR.
z. Scenario-Based Training (SBT). A training system that uses a highly structured script of real-world experiences to address flight-training objectives in an operational environment.
aa. Technical Personnel Examiner (TPE). TPE encompasses many types of GA designees. In previous versions of this order, TPE was a common reference for only DME and DPRE. Although most references to TPE have been removed in this revision, any TPE references remaining still apply only to DME and DPRE.
9. Office Information and Points of Contact (POC). The following offices play a role in designee management, from reviewing applicant qualifications to processing certification paperwork and writing policy for designee management. This list is not intended to be inclusive; however, it is provided as a resource for additional guidance where applicable.
a. Airman Certification Branch (AFS-760). AFS-760, which is part of the FAA Civil Aviation Registry (AFS-700), has final authority for the issuance of permanent airman certificates and maintenance of certification records. AFS-760 is located at the Mike Monroney Aeronautical Center (MMAC) in Oklahoma City, OK.
b. Designee Quality Assurance Branch (AFS-650). AFS-650, which is part of AFS-600, collects National Examiner Board (NEB) application materials from designee applicants.
c. Designee Standardization Branch (AFS-640). AFS-640, which is part of AFS-600, develops and conducts a variety of standardization seminars both domestically and internationally that are used by designees, designee applicants, representatives of delegations, and FAA personnel for initial training and renewal purposes.
d. Experimental Aircraft Association (EAA). The EAA is an international organization of aviation enthusiasts interested in flying, building, and restoring recreational aircraft. The EAA considers application materials submitted by NDPE/FEE applicants and recommends qualified designee applicants.
Sect › h. Regulatory Support Division (AFS-600). AFS-600 promotes safety by…
e. General Aviation & Commercial Division (AFS-800). AFS-800 is the FAA AFS division responsible for developing national policies, standards, systems, procedures, and programs for GA and advising senior FAA management on GA matters.
f. Light Sport Aviation Branch (AFS-610). AFS-610, which is part of AFS-600, manages and provides oversight of the SPE, SFIE, and the light-sport aircraft repairman training programs.
g. National Examiner Board (NEB). A board convened to oversee the designee application and screening process for AFS.
h. Regulatory Support Division (AFS-600). AFS-600 promotes safety by educating and advising users through the development, implementation, analysis, and distribution of technical information including airmen testing, designee standardization, and management of aviation data systems.
Sect › (a) DME/DPRE Applicants.
Chapter 2. Selection and Appointment
1. Selection.
a. Application. The managing Federal Aviation Administration (FAA) office selects qualified applicants for designee appointment. When selecting qualified candidates, the managing FAA office considers the recommendations from knowledgeable members of the aviation community. The National Examiner Board (NEB), or other evaluating entity, receives applications and reviews designee applications for the general eligibility requirements in paragraph 3 of this chapter.
(1) Designee applicants must complete an application package and submit it to the NEB for review and consideration. The package must contain a letter from the FAA office where the functions will be performed specifying that the complete application package has been reviewed and the applicant meets all the general requirements specified in paragraph 3 of this chapter. The application package must be mailed to: FAA, National Examiner Board, Attn: Designee Quality Assurance Branch (AFS-650), P.O. Box 25082, Oklahoma City, OK 73125-0082. Applicants should retain a copy of all application documents submitted to the FAA.
Note: Applicants requesting designation as an Airman Certification Representative (ACR), Flight Instructor Renewal Examiner (FIRE), Foreign Pilot Examiner (FPE), Ground Instructor Examiner (GIE), Military Competency Examiner (MCE), or Pilot Proficiency Examiner (PPE) must send their completed application forms directly to the managing FAA office for processing. Applicants already holding ACR, FIRE, FPE, GIE, MCE, or PPE designations and are applying for a designation to perform certification functions in an aircraft must submit an application for designation directly to the NEB.
Note: National Designated Pilot Examiner and Flight Engineer Examiner (NDPE/FEE) applicants must already possess an active DPE before submitting an NDPE/FEE application directly to the Experimental Aircraft Association (EAA) for consideration. The EAA submits recommendations of qualified designee applicants to: FAA, General Aviation and Commercial Division (AFS-800), 800 Independence Avenue S.W., Washington, DC 20591 for selection and appointment consideration.
Note: Current FAA employees will not be appointed as designees until their employment with the FAA has ended. FAA employees may not apply to the NEB earlier than 120 calendar-days before their actual date of retirement or separation from the agency. The application must include a letter of recommendation from the manager at their last assigned office. Appointments will be limited to functions performed while employed by the FAA, or other experience within the aviation industry. If a former FAA employee submits an application beyond 3 years from the date of separation, all application requirements apply.
(a) DME/DPRE Applicants. All DME/DPRE applicants must complete FAA Form 8110-28, Application and Statement of Qualification (DME/DPRE/DAR-T). The
Sect › (b) Demand/convenience to the public, as determined by the:
application package must also include legible copies of the applicable airman certificates held by the designee applicant.
(b) DPE Applicants. DPE applicants, other than Sport Pilot Examiner (SPE)/Sport Pilot Flight Instructor Examiner (SFIE) applicants, must complete FAA Form 8710-10, Designated Pilot Examiner Application. SPE/SFIE applicants must complete FAA Form 8710-12, Light-Sport Standardization Board-Designated Pilot Examiner Candidate Application. The application package must include a legible copy of airman and flight instructor certificates held by the designee applicant, and a copy of the designee applicant’s valid medical certificate (at least third class), if appropriate.
(2) The NEB will review designee applications (with the exception of ACR, FIRE, FPE, GIE, MCE, NDPE/FEE, and PPE) and rank those applicants meeting the requirements, when applicable. The NEB will notify the applicant (by letter) of the results.
Note: If the NEB determines a designee applicant is not qualified, the NEB Recorder will retain the application file for 4 calendar-months from the month of the evaluation, pending an appeal or request for additional information. At the end of the 4th calendar-month, the NEB Recorder will transfer the designee applicant’s application file to the NEB’s electronic database and discard the paper copies of the application file.
(3) The appointing FAA office will notify the NEB when it has determined a need for and possesses the ability to manage a designee.
(4) The appointing FAA office will notify the selected designee applicant. The selected designee applicant will register for and attend an initial training seminar. After the candidate successfully completes the initial training seminar, the designee applicant will provide the appointing FAA office with the certificate of completion from the initial training seminar.
Note: Designee applicants must successfully complete the initial training seminar before appointment. The designee applicant must be appointed within the 12-calendar-month period following completion of the initial training seminar. If the appointment process does not begin during the 12 calendar-months, the applicant must retake the initial training seminar. Once appointed, the recurrent training seminar is due 24 months after completing the initial training seminar.
b. Need for and Ability to Manage a Designee. Successfully meeting the eligibility requirements does not guarantee appointment as a designee. The managing FAA office, within its sole discretion, determines the need for and ability to manage a designee.
(1) Determining Need. The managing FAA office considers several factors in determining the need for a designee including, but not limited to:
(a) Activity level of current designees performing similar work in the managing FAA office’s geographical area.
(b) Demand/convenience to the public, as determined by the:
Sect › c. Serving Outside the United States. A designee may be appointed to…
• Ability to provide examinations within a reasonable period of time, and • Number of complaints from the public for lack of availability of certification.
(c) Geographic dispersion as determined by the distance an applicant must travel to get to the designee.
Note: The need for a new designee is driven by the needs of the public and not by the impact on other existing designees or the desires of air operators/agencies.
(2) Determining the Ability to Manage. The managing FAA office reviews several criteria to determine the ability to manage a designee including, but not limited to:
(a) Effect of workload on inspectors,
(b) Funding (e.g., travel allocation) needed to oversee the designee workforce, and
(c) Availability of trained ASIs (specialists) and/or managers.
2. Appointment. The appointing FAA office will complete the FAA Form 8000-5, Certificate of Designation, and a Certificate of Authority (COA) letter for presentation to the designee.
Note: By signing the designee application, the designee applicant acknowledges that the designation is a privilege, not a right, and that the FAA Administrator can terminate any designation at any time or for any reason he or she deems appropriate.
a. Applying for Reinstatement. Reinstatement is used in instances where a former designee is applying for privileges, after the not-for-cause termination of his or her designation, to the last managing FAA office that previously had jurisdiction over the designee. Former designees wishing to apply for reinstatement must submit the completed application directly to the managing FAA office and are not required to apply to the NEB if they previously held the same type of designation. The managing FAA office, in its sole discretion, will determine if there remains a need for the designee, and if it possesses the ability to manage the designee as described in subparagraph 1b. The former designee must meet the applicable training requirements described in this order.
b. Applying for Relocation. Designees may relocate to a different geographical area without applying to the NEB if the receiving FAA office agrees to the transfer. The designee must submit a new application to the receiving FAA office. The originating office must transfer the entire designee file to the gaining office.
c. Serving Outside the United States. A designee may be appointed to serve outside the United States if there is a demonstrated need that such designation will serve U.S. citizens abroad and that an FAA office can properly supervise the designee’s activities. The designee is subject to limitations as provided by current FAA policy regarding the certification of airmen outside the United States.
Note › Note
3. General Eligibility Requirements. The managing office must carefully consider all of the requirements before designating an applicant or renewing a designee. The general requirements for appointment, which are reviewed by the NEB, are:
a. Minimum Age. Minimum age of 23 years for all designees.
b. Personality Traits. Must exhibit integrity, professionalism, and sound judgment.
c. Training Requirement. Must have satisfactorily completed the applicable training requirement before appointment/renewal as a designee.
d. Knowledge of Guidance Materials. Must have access to, and adequate knowledge of, the current regulations, policies, directives, and related guidance material appropriate to authorized functions.
e. Command of English Language. Must be able to fluently read, write, speak, and understand the English language.
f. Objectivity. Must maintain the highest degree of objectivity while performing authorized functions.
g. Good Record. Must have a good record in the aviation industry.
h. Technology Access. Must have internet access, as well as access to a computer and printer with hardware/software sufficient to support the required activities.
Note: A designee is not required to be a U.S. citizen.
Note: Additional eligibility requirements for specific designee types are included in the applicable designee type specific chapters (Chapters 6 and 7) of this order.
Sect › 2. Initial Training Seminar.
Chapter 3. Oversight, Training, and Renewal
1. Oversight. Each designee operates under the direct supervision of the Federal Aviation Administration (FAA) office that holds the designation file, referred to as the managing FAA office. Supervision of designees includes the following functions:
a. Resolve Questions. FAA personnel who supervise the activities of designees must always welcome the opportunity to discuss current rules, procedures, and standards with designees upon request to resolve any questions the designee may have relating to their performance and responsibilities. Designees will direct any questions to their managing FAA office.
b. Test Observation. The FAA will observe Designated Mechanic Examiners (DME), Designated Parachute Rigger Examiners (DPRE), and Designated Pilot Examiners (DPE) when conducting their first test. Thereafter, FAA personnel may inspect or observe the designee at any time with or without prior notice.
c. Instruction. The designee must receive specific instructions from the managing FAA office regarding the proper conduct of his or her authorized functions.
d. Document and Submit Certification Files. Designees must submit certification files to the managing FAA office regardless of test results (pass or fail) within 7 calendar-days of the test date. DMEs must submit certification files to the managing FAA office regardless of test results (pass, fail, or not tested) within 7 calendar-days of the test date.
e. Check Knowledge and Accuracy of Certification Files. A critical component of the certification process is the accuracy of the certification files. The managing FAA office may check the designee’s aeronautical knowledge and certification procedures at any time.
2. Initial Training Seminar. Successful completion of the initial standardization seminar is a prerequisite for designation. Under most circumstances, if a designee applicant arrives after a course has started, the course manager will not permit that person to attend the remainder of the seminar. If he/she is more than 1 hour late, the course manager will not permit completion of the seminar. Should circumstances warrant accepting a late arrival, the course manager will require the applicant to make up the missed instruction with the instructor outside of normal class hours. Once the applicant has accomplished this, he/she will take the final examination with the class. Designees or applicants will be marked absent after 15 minutes has elapsed from the announced start time at the beginning of each day or after the announced start time following a scheduled break. Designees or applicants marked absent twice in the same seminar will not receive credit for the training and will not be allowed to complete the final examination with the class.
Note › Note
6/12/15 8900.2A CHG 1
Designee Type Initial Training Requirement DME/DPRE Initial Technical Personnel Examiner (TPE) Standardization Seminar DPE Initial Pilot Examiner Standardization Seminar
Note: Information regarding designee standardization seminars is available on the Designee Registration System Web site at https://av-info.faa.gov/DsgReg/default.aspx.
Note: Currently, initial training for certain designee types, including Airman Certification Representative (ACR), Flight Instructor Renewal Examiner (FIRE), Foreign Pilot Examiner (FPE), Ground Instructor Examiner (GIE), Military Competency Examiner (MCE), and Pilot Proficiency Examiner (PPE) applicants, are conducted by the managing FAA office.
3. Recurrent Training. Each designee is encouraged to attend safety meetings, aviation seminars, and other programs that contribute to the technical skills required for the designation. The designee is responsible for ensuring their training currency. Only after successful completion of the initial training (or initial standardization seminar) can the designee register for the recurrent training seminar. Attendance at a recurrent training seminar is mandatory. Designees or applicants will be marked as absent after 15 minutes has elapsed from the announced start time at the beginning of each day, or after the announced start time following a scheduled break. Designees or applicants marked as absent twice in the same course will not receive credit for the training and will not be allowed to complete the final examination with the class. The Certificate of Completion issued to those who successfully complete a recurrent training seminar will expire in the specified time period (see below) from the date shown on the certificate. The designee must forward a copy of the Certificate of Completion to the managing FAA office. The recurrent training requirements are set forth below:
Designee Type Recurrent Training Requirement DME 24 calendar-months—Recurrent Designated Mechanic Examiner Standardization Seminar DPRE 24 calendar-months—Recurrent Designated Parachute Rigger Examiner Standardization Seminar DPE performing flight checks in an 24 calendar-months—Recurrent Designated Pilot aircraft or FSTD Examiner Course Part I (Web-based) and Part II (one-day seminar) Administrative Privileges: ACR, FIRE, 24 calendar-months—Administrative Pilot Examiner FPE, GIE, or MCE Standardization Course (Web-based only)
Note: Designees may complete the Designated Pilot Examiner Initial Standardization seminar, conducted by AFS-640, in lieu of the recurrent training seminar to meet the recurrent requirement set forth in Chapter 3, paragraph 3 of this order.
Note: A designee must not exercise his or her designation privileges unless his or her training is current and up to date.
FAA Form 8710-6. › FAA Form 8710-6.
6/12/15 8900.2A CHG 1
4. Expiration. Initial appointment is for a period of 1 year. After the initial appointment period, the managing FAA office will determine the duration of the designation. The duration of the designation cannot exceed 3 years. The expiration date appears on the designee’s Certificate of Authority (COA) letter.
5. Renewal. A designee may be renewed if the continuation of the designation is justified, and the designation is in the FAA’s interest. The designee is responsible for submitting a timely renewal package. The FAA office must notify the designee that renewal has occurred and issue a new COA letter. A designation will be renewed under the following conditions:
• The managing FAA office determines that a need still exists; • The managing FAA office still has the ability to manage the designee; and • The designee continues to meet the eligibility requirements in Chapter 2, paragraph 3 and the specific requirements listed in the applicable designee type-specific chapter of this order.
a. Annual Meeting. The designee must attend an annual meeting held by the managing FAA office to discuss designee procedures, problems, and designation renewal.
b. Designee Maintains Designation. When conducting tests, each designee must maintain the applicable airman certificate(s), the general eligibility requirements listed in Chapter 2, paragraph 3 and the specific eligibility requirements in the designee type-specific chapters (Chapter 6 for DME/DPRE, and Chapter 7 for DPE) of this order.
c. Training Requirements. The recurrent training requirements in Chapter 3, paragraph 3 of this order must be completed.
d. Renewal Application Package. The designee must apply for renewal to the managing FAA office at least 45 calendar-days before the expiration of the designation. It is the designee’s responsibility to complete the renewal application package. The package must include:
(1) A copy of the designee’s current COA letter or previously issued FAA Form 8430-9, Letter of Authority;
(2) A record of all designee activity conducted since the issuance or last renewal of their designation;
(3) A current certificate of training showing the designee has successfully completed an initial or recurrent training seminar; and
(4) Additional application materials (as indicated below).
Designee Type Renewal Application Requirements DME/DPRE FAA Form 8110-28 with blocks 1, 2, 4, 5, 6, 7, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 22, 23, and 23a completed. The managing FAA office will approve the application for renewal by completing applicable blocks on the FAA application form. DPE FAA Form 8710-6.
Sect › 6. Knowledge and Skill.
e. COA Letter. After expiration of the designee’s COA letter, the designee may not exercise the privileges of the designation unless he or she has a current COA letter signed by the managing FAA office.
6. Knowledge and Skill. The determination that the designee’s knowledge of and application of current procedures and standards are adequate for renewal of the designation may be based on oversight of the designee and the designee’s attendance at a meeting or seminar conducted for the purpose of standardization.
Sect › c. Written Termination Appeal. If the designee wishes to appeal his or…
Chapter 4. Termination and Appeal
1. Termination. Termination is the action by the Federal Aviation Administration (FAA) to rescind a designation at any time for any reason the Administrator considers appropriate.
2. Types of Termination.
a. Termination for Cause. Termination for cause is a negative finding based on a designee’s performance. In the event that a reexamination of an airman under Title 49 of the United States Code (49 U.S.C) § 44709 becomes necessary due to an inadequate test performed by the designee, the managing office must immediately terminate the designee.
b. Termination Not-for-Cause. Termination not-for-cause can be for any reason not specific to a designee’s performance (e.g., lack of need for the designee or ability to manage the designee by the managing FAA office).
Note: A designee may voluntarily surrender a designation at any time. This voluntary surrender should be made in writing, sent to the managing FAA office manager, and be accompanied by the designee’s Certificate of Authority (COA) letter or previously issued FAA Form 8430-9, Letter of Authority.
3. Termination Letter. Designations are terminated under the general conditions contained in Title 49 of the United States Code (49 U.S.C.) § 44702. The managing FAA office manager makes the decision to terminate a designee. The decision regarding the termination of a designation will be provided to the designee in writing. Upon notification of termination (verbal or written) by the designee's managing FAA office, the designee must immediately cease the exercise of his or her designee privileges. In the case of verbal notification, the managing FAA office must follow up with written notification.
4. Appeal. The designee or designee applicant may request an appeal under certain circumstances. (Refer to FAA Order 8900.1, Flight Standards Information Management System (FSIMS), Volume 13, Chapter 5, Section 3, Termination and Appeal).
a. Appeal of Nonselection/Nonappointment. The National Examiner Board (NEB) handles appeals of nonselection. Contact the Designee Quality Assurance Branch (AFS-650) for further information.
b. Nonappeal Termination. Termination based on the lack of need, the inability of the managing FAA office to manage the designee, loss of a prerequisite certification, or failure to meet training requirements cannot be appealed.
c. Written Termination Appeal. If the designee wishes to appeal his or her termination, the designee must make the request in writing within 14 calendar-days of receipt of the written notification of the FAA office manager’s decision to the regional appeal panel by sending a letter to the FAA office manager requesting an appeal.
Note: The regional appeal panel’s decision is final. › Note: The regional appeal panel’s decision is final.
d. Written Notification. The designee will be notified in writing of the appeal panel’s decision within 60 calendar-days.
Note: The regional appeal panel’s decision is final.
Chapter 5. Privileges, Limitations, and Responsibilities
1. Privileges. A designee is authorized to:
a. Accept Airman Certificate/Rating Application. Accept applicable airman certificate and/or rating applications for airman certificates and ratings.
Sect › (1) If the applicant has a valid verification letter of authenticity…
Designee Type FAA Form Designated Mechanic Examiner FAA Form 8610-2 (DME)/Designated Parachute Rigger
Examiners (DPRE) Designated Pilot Examiner (DPE) FAA Form 8710-1 or FAA Form 8710-11
b. Conduct Tests. All tests must be in the English language, appropriate to the Federal Aviation Administration (FAA) Certificate of Authority (COA) letter held by the designee, and in accordance with the appropriate practical test standards (PTS).
c. Charge Reasonable Applicant Fees. The designee must ensure that the applicant understands all fees charged, including the fee for retesting after failure, before the designee accepts the airman certificate and/or rating application.
Note: Ensure that the DME/DPRE only accepts payment from the applicant or on behalf of the applicant and that the designee remains a private person acting as a representative of the Administrator in accordance with Title 14 of the Code of Federal Regulations (14 CFR) part 183, subpart C.
d. Issue Temporary Airman Certificates. Issue Temporary Airman Certificates only to applicants who have been tested and found qualified for the certificate or rating sought. The managing FAA office may remove this authorization and retain this privilege. In this case, limitations will be entered on the COA.
e. Accept Pilot Applications (DPE Only). DPEs may accept pilot applications for new pilot certificates and/or ratings (for which the DPE holds that designation and authority) and any pilot certificate that is administrative in nature (e.g., second-in-command (SIC) type rating or English language endorsement), provided the DPE has received initial training from the managing FAA office and recurrent training, offered by AFS-640 every 24 calendar-months thereafter.
(1) If the applicant has a valid verification letter of authenticity and makes an appropriate application, DPEs may accept applications for 14 CFR part 61, § 61.75 pilot certification that are issued on the basis of a foreign pilot license, for adding the “English Proficient” endorsement, paper to plastic pilot certificates, as well as replacement of the § 61.75 pilot certificate. Section 61.75 pilot certificate holders will not be able to apply via the web. This requires the applicant to apply in person so there will be positive identification at the time of application to an appropriately authorized DPE, Foreign Pilot Examiner (FPE), FAA aviation safety technician (AST), or FAA aviation safety inspector (ASI). DPEs and FPEs must comply with the guidance in Chapter 7, Sections 20 and 21.
Sect › i. Airman Knowledge Test. When a knowledge test is required, a designee…
(2) DPEs may not accept an application for a name change, citizenship change, DOB change, gender change, dual citizenship, any other changes to personal data, or for the removal of an English language limitation. If the guidance in the appropriate FAA order specifically requires a managing FAA office to handle the applicant, then a DPE may not perform that function. Changes of a personal nature (name change, sex change, removal of the English language limitation, etc.) that specifically require the applicant to perform the certification action at the managing FAA office must be performed by authorized FAA personnel at the managing FAA office.
2. Limitations.
a. Observing a Test. A designee must not allow anyone other than an ASI to observe a test. For designee training purposes only, exceptions may be authorized in writing by the managing FAA office.
b. Locations. DMEs/DPREs must not conduct tests at locations not listed as a base of operation on the current COA letter held by the designee, unless authorized by the managing FAA office. DPEs must not conduct tests at locations outside their geographically assigned area, unless geographic expansion is authorized (see subparagraph 2l).
c. Computerized Airman Knowledge Tests. A designee must not conduct or monitor any portion of computerized airman knowledge tests.
d. Expired Temporary Airman Certificate. A designee must not reissue or amend any expired Temporary Airman Certificate.
e. Permanent Airman Certificate. A designee must not endorse, amend, alter, or issue any permanent airman certificate.
f. Applicable PTS. A designee must not exempt any applicant from the testing requirements in the applicable PTS.
g. Teaching/Testing. A designee must not combine teaching with testing during the testing of an applicant.
h. Proof of Eligibility. A designee must not conduct tests unless an applicant presents proof of eligibility as prescribed in the applicable 14 CFR part (as set forth below):
Designee Type 14 CFR DME/DPRE Part 65 DPE Part 61 and Part 141
Note: Additional limitations that are designee type specific are located within the designee type-specific chapters of this order.
i. Airman Knowledge Test. When a knowledge test is required, a designee must not conduct an oral and a practical test unless the applicant provides the required airman knowledge test results with a passing score.
Sect › 3. Responsibilities.
Note: This does not apply to aviation mechanic applicants authorized to test in accordance with 14 CFR part 65, § 65.80 or master parachute rigger applicants that hold a senior certificate.
j. Applicant Further Study. A designee must not temporarily suspend a test to allow the applicant further study, and then continue the same test later.
k. Number of Applicants. A designee conducting an oral and/or practical test must not test more than one applicant at a time. To clarify “at a time”: when a designee begins a test with an applicant, prior to accepting an application from another airman, the designee will terminate the first test with the issuance of a Temporary Airman Certificate, a notice of disapproval, or a letter of discontinuance.
l. Geographical Area. A designee must not test an applicant outside the authorized geographical area. For a DPE, the test must start and conclude within the authorized geographical area. If a designee wants to administer tests outside the geographical area of the managing FAA office, the designee must:
(1) Request authorization in writing from the managing FAA office.
(a) Provide the date and address of the testing site in writing.
(b) Make the request in writing at least 7 working days prior to the scheduled activity.
Note: The managing FAA office with jurisdiction over the test site may evaluate the facilities, equipment, current publications, and test materials required to conduct a test for the certificate and/or rating(s) sought.
(2) Receive approval in writing from the designee’s managing FAA office, as appropriate. The managing FAA office will coordinate with the geographical office (receiving office).
(3) The designee submits the certification file to his or her managing FAA office. The receiving FAA office with jurisdiction over the test location may request copies of any files for tests conducted by the designee in their area.
m. Language Requirement. A designee must not conduct tests in any language other than English.
n. Applications Not Accepted. Designees must not accept applications for medical Statements of Demonstrated Ability (SODA) or for the reexamination of airmen under Title 49 of the United States Code (49 U.S.C.) § 44709.
3. Responsibilities. Each designee must represent the Administrator in a manner that reflects positively on the FAA.
Sect › e. Knowledge and Skill. A designee must maintain a high degree of…
a. Honor Appointments. Designees should honor appointments made as promptly as possible. The designee is also expected to make his or her services available to all applicants on an equitable basis.
b. Undivided Attention. Designees must give undivided attention to the applicant during the entire testing period.
c. Private/Confidential Discussion. Designees must ensure that discussion following any test is private and is confidential.
d. FAASTeam Seminars/Events. The FAA encourages designees to participate in FAA Safety Team (FAASTeam) seminars and events. The FAA values the participation of designees as FAASTeam representatives in providing support for safety meetings.
e. Knowledge and Skill. A designee must maintain a high degree of knowledge and skill in the subject areas required for airman certification, evaluation, and testing techniques.
Sect › (d) Five years continuous experience immediately before designation…
Chapter 6. Designated Mechanic Examiner (DME) and Designated Parachute
Rigger Examiner (DPRE) Program
Section 1. DME—General
1. Additional Requirements for Appointment. The procedures contained in this chapter apply to inspectors, DMEs, authorized to conduct aviation mechanic or parachute rigger oral and practical tests and issue Temporary Airman Certificates. DMEs will conduct tests in accordance with the applicable practical test standards (PTS). Inspectors must carefully consider all of the following issues before designating or renewing a designee. In addition to meeting the general designee eligibility requirements in Chapter 2, a designee applicant must meet the following additional requirements, which will be reviewed by the appointing Federal Aviation Administration (FAA) office:
a. For DME Appointment.
(1) Evidence of a high level of knowledge and experience in the subject areas required for aviation mechanic certification in both reciprocating and turbine-engine aircraft.
(2) Previously held a valid aviation mechanic certificate for 5 years with the rating(s) for which a designation is to be issued.
(3) Applicants must also meet one of the following experience requirements listed below.
Note: These requirements may not be combined.
(a) Five years experience actively exercising the privileges of a valid aviation mechanic certificate in accordance with Title 14 of the Code of Federal Regulations (14 CFR) part 65, § 65.81(a) on U.S.-registered civil aircraft. Three of the 5 years of experience required must be immediately before designation.
(b) Five years experience performing maintenance on U.S.-registered civil aircraft while employed by an FAA Repair Station (14 CFR part 145). Three of the 5 years of experience required must be immediately before designation.
(c) Five years experience performing maintenance on U.S.-registered civil air carrier aircraft operating under 14 CFR part 121 or 135. Three of the 5 years of experience required must be immediately before designation.
(d) Five years continuous experience immediately before designation instructing aviation maintenance while employed by an FAA Aviation Maintenance Technician School (AMTS) (14 CFR part 147). Also, the applicant must have been concurrently (in addition to the 5 years of experience as an instructor for an AMTS 14 CFR part 147 certificate) and actively exercising the privileges of a valid aviation mechanic certificate in accordance with § 65.81(a) for three years on U.S.-registered civil aircraft (certificated and maintained in accordance with 14 CFR.)
Sect › 3. Designee Materials.
Note: Applicants should provide enough verifiable detail in their application package to allow the National Examiner Board (NEB) to determine that they meet the general eligibility requirements of Chapter 2 of this order as well as those requirements specific to the applicable designee type.
(4) Have a fixed base of operation equipped to support testing in accordance with the required equipment contained in the Minimum Tools and Equipment List (MTEL) located in Figures 6-2P. This includes both reciprocating and/or turbine engine aircraft.
(a) The fixed base of operation, equipment, and materials must allow an applicant to demonstrate the basic skills for the certificate and rating sought. The managing FAA office will monitor the status of equipment periodically to ensure compliance.
(b) Use Airworthy aircraft, other aircraft, aircraft subassemblies, operational mockups, or other aids for testing airman applicants.
(c) All tools, equipment, current publications, materials, etc., required to complete a project assignment are included in the computer-generated practical tests. See Figure 6-2P for the required equipment list.
b. Limitations. In addition to the general limitations in Chapter 5, DMEs:
(1) Must not conduct oral and practical tests at any location unless it is adequately equipped with available equipment and material necessary for conducting the tests. For DMEs, this includes the required equipment contained in the Minimum Tools and Equipment List (see Figure 6-2P).
(2) Must not conduct an oral or practical test in any language other than the English language.
2. DME Designations Issued. The DME can be issued the following designations:
a. Airframe. Conducts aviation mechanic airframe rating oral and practical tests and the general oral and practical test, when required.
b. Powerplant. Conducts aviation mechanic powerplant rating oral and practical tests and the general oral and practical test, when required.
c. Airframe and Powerplant (A&P). Conducts aviation mechanic A&P ratings, oral and practical tests, and the general oral and practical test, when required.
3. Designee Materials. The managing FAA office should provide each designee with materials appropriate to the designation. The managing FAA office may issue some or all of the designee materials at the time of appointment. With the exception of the FAA Form 8060-4, the material can also be found on the Internet, or through common sources such as the Government Printing Office (GPO). The following materials (current editions) are necessary to perform DME duties:
• II—Airframe Structures. › • II—Airframe Structures.
a. FAA Order 8900.2, General Aviation Airman Designee Handbook.
b. FAA Form 8610-2, Airman Certificate and/or Rating Application (Stock No. 0052-00-026-8004).
c. FAA Form 8060-4, Temporary Airman Certificate (Stock No. 0052-00-049-5001).
d. FAA Form 337, Major Repair and Alteration (Stock No. 0052-00-025-8000).
e. Title 14 CFR Part 65, Certification: Airmen Other Than Flight Crewmembers.
f. Title 14 CFR Part 183, Representatives of the Administrator.
g. FAA-S-8081-26, Aviation Mechanic General Practical Test Standards (PTS).
h. FAA-S-8081-27, Aviation Mechanic Airframe Practical Test Standards (PTS).
i. FAA-S-8081-28, Aviation Mechanic Powerplant Practical Test Standards (PTS).
4. Security. Each DME is responsible for establishing and carrying out appropriate security procedures. The security of the controlled material is important to prevent compromise, and to ensure the applicants meet the aeronautical skill standards for aviation mechanic certificates and ratings.
a. Materials. The DME must ensure adequate security of all test questions or projects (printed or downloaded). These materials must not be used for any other purpose.
b. Access. The DME must secure the aforementioned material in a manner that will not allow unauthorized access (e.g., a locked drawer, cabinet, or closet). Only authorized representatives of the FAA Administrator will receive access to secured material. The DME should refer any public request for the secured material to the managing FAA office.
5. FAA Certification Policy. DME must evaluate the oral and practical tests to determine if an applicant’s performance is acceptable or unacceptable. The primary discriminator in the airman certification process is the oral and practical test. Standard grading criteria and objective examination ensure a level of basic knowledge and skills in all subjects required for the rating sought.
6. Aviation Mechanic Tests. The PTS are contained in three separate booklets (General, Airframe, and Powerplant), which consist of knowledge (oral question) elements and skill (practical project) elements in each of the 5 sections. Section I, General, is required for either the airframe or powerplant rating and applies to both. Sections I, II, and III are required for the airframe rating. Sections I, IV, and V are required for the powerplant rating. See Chapter 6, Section 2, paragraph 8 for information concerning previously passed section I. These test sections include:
• I—General. • II—Airframe Structures.
Sect › d. Advise of Retesting. Advise applicant of § 65.19 retesting after…
• III—Airframe Systems and Components. • IV—Powerplant Theory and Maintenance. • V—Powerplant Systems and Components.
Note: Aviation mechanics oral and practical tests are required to be downloaded from the Designee Standardization Branch’s (AFS-640) oral and practical test generator.
Section 2. DME—Conducting and Grading Tests
7. Preparation: Conduct a Pretest Interview. The DME must accomplish the pretest interview face-to-face, by telephone/fax, through email, or by other methods that will allow the DME to:
a. Discuss Testing Details. Discuss fees, testing procedures, projects, and type of equipment to be used and what the applicant should expect if they pass, fail, or do not complete the test.
(1) Charge a Reasonable Fee. The DME may charge a reasonable fee to each applicant for handling the forms and reports incident to the issuance of an aviation mechanic certificate, for the use of the DME’s facilities, equipment, and materials, and service in administering the oral and practical tests.
(2) Fee Agreement. The DME and the applicant should reach a mutual understanding and agreement of the total fee for the services before beginning the tests. An agreement in writing may be to the advantage of both the DME and the applicant
b. Advise of Testing Schedule. Advise the applicant when the day’s activities terminate, and when testing resumes if more than 1 day is needed.
c. Ensure the Applicant’s Eligibility. (See paragraph 9.)
(1) Review the applicant’s FAA Form 8610-2 for completeness and correctness. The DME must have the applicant correct any errors. This may require the applicant to return to the FAA office where authorization was obtained.
(2) Review the applicant’s current written test results that are applicable to the rating(s) sought.
(3) Have the applicant indicate, in the event that he or she passes all of the required tests, how he or she will respond to the two questions listed in block IV, “APPLICANT’S CERTIFICATION,” located on the reverse side of FAA Form 8610-2. There may be a need to have managing FAA office involvement if the applicant would be required to answer “YES” to either of the questions.
d. Advise of Retesting. Advise applicant of § 65.19 retesting after failure provisions and restrictions.
Sect › (2) For the DME: The General Section of the Test.
Note: DME must notify the managing FAA office, in writing, before conducting all oral and practical tests. This can be done by email, fax, or other written means acceptable to the managing FAA office. The managing FAA office will establish specific procedures for this notification.
Note: These procedures must include annotation to indicate if the applicant was authorized to test by an inspector from an FAA office other than the DME’s managing FAA office.
8. Knowledge and Skill Elements for DME.
a. Download Knowledge and Skill Elements. DMEs must use the knowledge (oral) and skill (practical) elements downloaded from AFS-640’s Web site (https://av-info.faa.gov/DsgReg/Login.aspx) to administer the oral and practical tests. The completed test planning sheet must be included in the certification package sent to the managing FAA office.
(1) If the DME downloads and administers a test, the test planning sheet must be forwarded with the certification package to the managing FAA office. The tests must not be copied or reused. Generated tests not used must be destroyed.
(2) The DME is required to use questions and projects obtained from the Internet based Oral and Practical Test Question Generator at: https://av-info.faa.gov/DsgReg/Login.aspx. Select and develop required tests and then download the applicable types of tests to be administered.
(3) Each test is downloaded for each specific applicant and must not be copied or reused.
b. Prescribed Length of Time. The testing period must be long enough to make a valid determination in each subject area/Area of Operation for the rating sought. Take appropriate time to ensure that all required knowledge element questions and skill element practical projects have been completed for the rating sought.
(1) Progressive Tests Must Not Be Given. Although it may be necessary to continue a test for more than 1 day, tests must not be allowed to continue for long periods. Progressive testing is defined as testing which continues for more than 4 sessions in a 4-day period. Suspending the test to allow the applicant further study is not allowed. Both the applicant and the designee should plan the testing times so the applicant completes most of the test once it commences.
Note: A session is defined as any break in testing that is separated by more than 2 hours.
(2) For the DME: The General Section of the Test. The DME should not begin a test with the intent of testing the General section only. Applicants for an airframe rating must take sections I, II, and III. Applicants for a powerplant rating must take sections I, IV, and V. An applicant is not required to take section I, General, of a knowledge or skill test for a mechanic rating if it was previously passed. Proof of passing may be in the following forms:
Sect › (a) Evaluate the experience documents and verify them, if necessary.
• A mechanic certificate with the alternate rating; or • FAA Form 8610-2 that shows section I, General, has been passed within the preceding 24 calendar-months (although other sections may not have been passed).
9. Applicant Eligibility.
a. Furnish Current, Government-Issued Identification. Applicants must furnish current, valid, government-issued identification with a photograph and signature. If FAA Form 8610-2 is completed at an FAA office, the approving inspector will record the method of identification (e.g., passport, U.S. military identification, or U.S. driver’s license, including state of issuance), number, and expiration date in the “REMARKS” area of FAA Form 8610-2. The DME will verify the applicant’s identification before testing. If the means of identification was provided in the “REMARKS” area, the DME will verify the identification and initial the inspector’s entry. (Sample entry: Oklahoma Driver’s License #123456789 exp. 01/31/20XX.) If the means of identification was not previously entered in the “REMARKS” area or the means of identification provided by the applicant is different from the one listed in the “REMARKS” area, the DME will make the entry in the “REMARKS” area and initial the entry. (See Figures 6-2F to 6-2K (mechanic applicants).)
Note: The aviation safety inspector (ASI)/DME will have the applicant fill out the Pilot’s Bill of Rights (PBR) acknowledgement (refer to FAA Order 8900.1, Flight Standards Information Management System (FSIMS), Volume 7, Chapter 8, Section 1) prior to filling out FAA Form 8610-2.
b. Meet English Language Requirements. Both designees and ASIs share the responsibility for determining if applicants meet the English language requirements. (Before accepting the application and beginning the practical test for certificate or rating, the designee/ASI must evaluate the applicant’s English fluency using the appropriate guidance.) The current edition of Advisory Circular (AC) 60-28, English Language Skill Standards Required by 14 CFR Parts 61, 63, and 65, provides guidance for airman applicants, designees, and ASIs in determining English language skills required for airman certification.
c. Original FAA Form 8610-2.
(1) Only maintenance or avionics inspectors who hold the mechanic certificate with airframe and/or powerplant ratings are authorized to review and endorse block V of FAA Form 8610-2.
(2) All applicants claiming civilian and/or military experience as a basis for qualification must have the experience evaluated and verified by an inspector before taking the required test. The inspector may, as a matter of office procedures, reproduce and retain copies of FAA Form 8610-2 and documented evidence presented by the applicant. The ASI will:
(a) Evaluate the experience documents and verify them, if necessary.
Note › Note
(b) Have the applicant complete FAA Form 8610-2 (two originals). (See Figures 6-2A, 6-2B, 6-2D, and 6-2E.) Provide a copy of Figure 6-1 to the applicant. Instruct the applicant to detach, if necessary, and read the “PRIVACY ACT” area of FAA Form 8610-2.
(c) Review FAA Form 8610-2 for completeness, sign, and complete block V of FAA Form 8610-2 (both originals), and return them if the applicant meets the experience requirements. Return all experience documents to the applicant. Both original FAA Form 8610-2 applications must be retained by the applicant to present to a DME or ASI for the oral and practical tests.
d. Two Originals.
(1) The applicant submits two originals of FAA Form 8610-2, Airman Certificate and/or Rating Application, before testing begins. The applicant must complete FAA Form 8610-2 in accordance with Figure 6-1, Instructions for Completing FAA Form 8610-2, Airman Certificate and/or Rating Application, which includes the instructions for completing FAA Form 8610-2. The ASI or designee should provide FAA Form 8610-2, which can be found at www.faa.gov, and give detailed instructions for completing it correctly. (The ASI or designee must copy Figure 6-1 and provide it to the applicant until FAA Form 8610-2 is revised with written instructions attached.) Advise the applicant to read the supplemental information attached to FAA Form 8610-2 (see Figure 6-1).
Note: All signatures must be original, in dark ink, with the name printed or typed below or next to the signature.
Note: The block V endorsement must not be restricted to a specific FAA office or region.
Note: An applicant is not required to present his or her application to an FAA office for reauthorization unless there is evidence that his or her original authorization is in question. Any evidence should be attached on a separate sheet of paper or annotated in the remarks section.
(2) For the DME: Applicants attending or graduating from an approved AMTS.
(a) The designee must ensure the graduation certificate or certificate of completion includes the following:
• Name and certificate number of the AMTS; • Graduation date; • Curriculum from which the applicant graduated (i.e., airframe and/or powerplant); • Name of the applicant; and • Signature from authorized school official.
Note: If the designee has reason to question the validity of the graduation certificate, contact the managing FAA office prior to starting the test.
Sect › (a) For the DME
Note: A copy of the graduation certificate or certificate of completion will be attached to the certification file, and must be sent to AFS-760 through the DME’s managing FAA office.
(b) Taking Oral and Practical Tests Before Taking Airman Knowledge Tests. AMTS students may be authorized by the managing FAA office to take the oral and practical tests before the computerized airman knowledge test in accordance with § 65.80.
1. Each student must complete the front of FAA Form 8610-2 (both originals). FAA Form 8610-2 must show the AMTS’s name and location (block II, item D1), AMTS’s certificate number (block II, item D2), curriculum in which student is enrolled (block II, item D3), and graduation date (block II, item D4). Applicants should not check block II, item D, “GRADUATE OF APPROVED COURSE.”
2. AMTSs must show that each student is in the final phase of training and has maintained satisfactory progress at the school.
Note: The student must be within 45 calendar-days of completing that phase of the curriculum. If enrolled in the airframe only or powerplant only curriculum, the student must be within 45 calendar-days of completion of the general and airframe curriculum or the general and powerplant curriculum. If the applicant is enrolled in the powerplant curriculum, and has completed the general and airframe curriculum, he or she must be within 45 calendar-days of completion of the powerplant curriculum. If the student is enrolled in the combined A&P curriculum, he or she must be within 45 calendar-days of completion of the complete curriculum for the combined A&P, have made satisfactory progress, and be prepared for the test. The proper AMTS official must complete block II, item E, (1) and (2).
3. Inspectors must complete block II, item F, (1), (2), (3), and (4). The FAA authorization expiration date must not be later than the anticipated graduation date. Process the completed file through the managing FAA office. (The managing FAA office has authorized testing of any student by a DME by completing block II, item F, (1), (2), (3), and (4).)
10. Conducting the Tests.
a. Conducting the Oral Test.
(1) Oral questions may be used at any time during the practical test.
(a) For the DME: All oral test questions must be downloaded from the Designee Registration System (DRS) test generator. Results of oral questions must only be recorded as Pass, Fail, or Not Tested. Ask a minimum of four but no more than seven questions in each subject area. (Example: one question missed in the minimum of four required questions equals 75 percent; two questions missed in the minimum of four questions will require an additional three questions to be asked. Provided the applicant did not fail any further questions, the applicant would score 71 percent). The applicant must successfully answer at least 70 percent of
Sect › (4) Provide all tools, equipment, and reference materials for the…
the oral questions asked in each subject area. Each subject area must be passed in order to pass a section.
Note: All unused generated tests must be destroyed.
(2) An applicant’s answers to oral questions must show an understanding of the subject and ability to apply knowledge. Do not allow an applicant’s skill of oral expression or ability to memorize details affect oral test evaluation. If necessary, additional exploratory questions may be used to verify the applicant’s understanding of the subject area, but will not be considered as part of the test.
(3) To determine if the oral questions are answered correctly, the DME must be able to reference information (e.g., manufacturer’s data, ACs, and 14 CFR), and be objective in making the determination.
(4) Although the answers to the oral questions should be available in the CFRs, manufacturer’s maintenance data, or other aviation related data, the applicant must be able to successfully answer all oral questions without the use of any reference materials.
b. Conducting the Practical Test. All questions and practical projects downloaded from the DRS test generator must be tested. Results of practical questions must only be recorded as Pass, Fail, or Not Tested.
(1) Make an objective determination of the applicants performance in each subject area tested.
Note: All required projects shall be successfully accomplished on the first attempt.
(2) Personally observe all practical projects in their entirety performed by the applicant.
(3) Determine if the applicant’s completed project is acceptable. Be objective in making this determination. The applicant must be able to demonstrate satisfactory proficiency and competency using basic aircraft mechanic skills. The applicant must demonstrate an approval for return to service standard, where applicable, and demonstrate the ability to locate and apply the required reference materials, where applicable. For instances where an approval for return to service standard cannot be achieved, the applicant must be able to explain why the return to service standard cannot be met (e.g., when tolerances are outside of a product’s limitations).
(4) Provide all tools, equipment, and reference materials for the subject area elements downloaded from the oral and practical test generator. These materials must include, but are not limited to: 14 CFR, Type Certificate Data Sheets (TCDS), Airworthiness Directives (AD), ACs, manufacturer’s technical and parts manuals, service information, and any other instructions and/or reference materials that are necessary for the objective accomplishment of the assigned subject area element(s). All reference material must be unmarked and in good condition. The applicant’s use of other reference material, not provided by the DME, is prohibited. Use of nonprogrammable calculators is permitted where appropriate. The use of electronic devices with
Sect › (6) Application of appropriate rules.
camera capabilities (i.e., tablets, cell phones, etc.) is prohibited. Applicants may use personal tools and equipment at the discretion of the DME.
11. Evaluating Applicant Performance. Do not expect an applicant to be competent in all phases of overhaul, maintenance, alteration, and repair, or be highly skillful in performing complex manipulative operations. However, expect the applicant to have developed basic skills and be able to demonstrate them during the practical test. Inform the applicant of the level of performance expected before beginning each project. DMEs can find the required performance levels in the PTS.
a. For the DME. When it becomes obvious during the test that an applicant cannot perform at an acceptable level and has already failed a subject area, the DME must discontinue testing in that section. The DME must discontinue the testing any time there is a failure of a subject area in a section.
Note: Knowledge Questions (Oral). Once the applicant has failed a subject area in the Knowledge Questions (Oral) test in a section, the entire oral section must be retested. The applicant must retake the appropriate section failed at the next retest examination. The applicant will be retested on all oral questions from each subject area in the previous failed section. This process will continue until the applicant passes each section.
Note: Skill Element Projects (Practical). Once the applicant has failed a subject area in the Skill Element practical test in a section, the entire section must be retested. The applicant must retake the appropriate section failed at the next retest examination. The test generator will carry over the last failed project in a section to the retest examination. This process will continue until the applicant passes each section.
b. Standards. Include the following standards in DME observations for evaluating applicant performance:
(1) Approach to the project; proper information and tools; preparation of the equipment; and observation of safety precautions.
(2) Cleaning, preparing, and protecting parts; skill in handling tools; thoroughness and cleanliness.
(3) The functions of the units or systems of the assigned project; use of current maintenance and/or overhaul procedures.
(4) Final inspection for safety and operation.
(5) Completion of required forms and records.
(6) Application of appropriate rules.
Sect › (2) Present an appropriate computerized Airman Knowledge Test Report…
(7) Attitude toward safety, manufacturer’s recommendations, and acceptable industry practices.
c. Test Planning Sheets Are Required for Each Oral and Practical Test Given. Forward test planning sheets to the managing FAA office with the certification file. An example of a planning sheet is included in Figure 6-4A. The managing FAA office may also require additional information on the planning sheets.
Note: The applicant’s signature on the planning sheet verifies the test was given to the applicant and the test times and dates listed are accurate, and the designee should explain the significance of the signature on the planning sheet.
Note: Copies of test planning sheets are no longer required to be kept in the managing FAA office file and should be included in certification packages forwarded to the Airmen Certification Branch (AFS-760). However, FAA offices may choose to retain a copy of the test planning sheet in the designee’s file.
d. Tests Not Completed.
(1) If the test cannot be completed in the allotted timeframe, the designee will correctly mark both FAA Forms 8610-2 (two originals) on the reverse side. Forward this test not completed file to the managing FAA office within 7 calendar-days. When practical, schedule a retest for the areas not completed at the time the test is discontinued. Treat this retest as if the applicant had failed those portions not tested. (See subparagraphs 11e.)
(2) For the DME: Correctly mark for the subject areas completed. Incomplete subject areas will not be marked as a failure on the FAA Form 8610-2 (two originals). In addition, the DME shall place a statement in the “REMARKS” area indicating why the test was not completed. Some examples are located in the figures at the end of this chapter.
Note: Do not start any test without the intent to complete the testing for the issuance of a certificate and at least one rating or an added rating.
e. Retests. Retest applicants in all areas of the oral and/or practical tests in the section(s) listed as failed, that were not tested, or that have expired. When application is made for a retest after failure of a previous test or tests not completed, the applicant must:
(1) Complete FAA Form 8610-2 (both originals) in accordance with the instructions furnished by the DME or ASI.
Note: FAA Form 8610-2, block V does not need to be signed by an ASI if a copy of the original FAA Form 8610-2 (with authorizing signature) is attached to the file.
(2) Present an appropriate computerized Airman Knowledge Test Report (AKTR). All sections of the test must have been passed within the previous 24 calendar-months.
Sect › b. Return Original. Give one original of FAA Form 8610-2 to the…
(3) Present his or her original of FAA Form 8610-2 from the previous oral and practical tests showing the sections or Areas of Operation failed, not completed, or for which passing credit has expired (mechanic applicants only).
(4) If the retest is within 30 calendar-days of the previous test, present a statement by a person authorized in § 65.19 that the applicant received additional instruction for each subject failed and the applicant is ready for retesting. This statement of training is required only when the applicant failed portions of the test. This statement of training is not required for subject areas not completed on the previous test. (See Figures 6-2N.)
12. Recording the Results of Tests. Record the results of oral and practical tests on the reverse side of FAA Form 8610-2.
a. When the applicant has demonstrated an acceptable level of competence, workmanship, and safety in each subject area, check the “PASS” box for that portion of the section (oral or practical test) and enter the expiration date. If the applicant fails, check the “FAIL” box and fill out the QUES. NO and/or PROJ. NO. box, as appropriate, with the project number or the oral question number(s) that was (were) failed, but do not enter an expiration date when the applicant fails the section. Make all entries in permanent dark ink. See paragraph 15 for procedures to follow if an applicant fails.
b. The expiration date for each oral and practical test section is 24 calendar-months after the section is passed. (Example: A test section passed on any day in August 2011 will expire on 08/31/2013.)
13. When the Applicant Passes. When the applicant has passed all the required sections of both the oral and practical tests, the designee who administered the test must:
a. Complete Reverse Side of FAA Form 8610-2. Complete as follows:
(1) Enter the date the test was completed, sign the form, and enter his or her designation number in the spaces provided on the reverse of FAA Form 8610-2 (both originals).
(2) Require the applicant (at the time the Temporary Airman Certificate is issued) to complete the “APPLICANT’S CERTIFICATION” area on the reverse side of FAA Form 8610-2 (both originals), following the Designated Examiners Report. Use the “APPLICANT’S CERTIFICATION” area to verify the applicant still meets the conditions and requirements of §§ 65.11 and 65.12.
Note: At the time of issuance of FAA Form 8060-4, the inspector and/or the designee must request a telephone number where the applicant may be reached during the next 120 calendar-days in the event of application problems. The telephone number must be recorded in the “REMARKS” area on the back of the application. If a telephone number is not available, write “NO TELEPHONE.” The inspector and/or the designee may also request an email address.
b. Return Original. Give one original of FAA Form 8610-2 to the applicant.
Sect › (4) Forward the typed original FAA Form 8060-4, the computerized…
c. Prepare Temporary Airman Certificate. If authorized on the COA, prepare FAA Form 8060-4 unless otherwise directed by the managing FAA office. (See Figures 6-2L to 6-2M.) Issue the duplicate copy to the applicant. Forward the original typed copy with the certification file to the managing FAA office. Ensure FAA Form 8060-4 reflects the applicant’s current information. Changes involving the applicant’s name, gender, nationality (including dual citizenship), and/or date of birth (DOB) must be referred to the managing FAA office.
(1) Entries for the applicant’s copy may be printed in ink; however, a typed original, signed by the issuing DME, must accompany the certification file, which must be forwarded to the managing FAA office. The applicant need not sign the copy sent to the managing FAA office.
(2) AFS-760 will issue all original airman certificates with a unique certificate number during the processing of the airman file. The airman’s Social Security Number (SSN) can still be collected on FAA Form 8610-2, but the word “PENDING” must be placed in the certificate number block III of FAA Form 8060-4. If the airman does not wish to provide his or her SSN to the FAA, the applicant must place the words “DO NOT USE” in the SSN block of the application. Airman certificates presently using the SSN as a certificate number will continue to be issued with that number unless the applicant requests a unique number. If the airman requests a unique number when applying for an added rating, the word “PENDING” must be placed in the certificate number block of FAA Form 8060-4.
d. When Authorized under § 65.80 (Mechanic Applicants Only). If the applicant has been authorized under § 65.80 to take the oral and practical tests before the computerized airman knowledge tests and passes them, the designee will do the following:
(1) Give the applicant a completed and signed original of FAA Form 8610-2. This original is required when the applicant applies for a certificate after passing the computerized airman knowledge tests.
(2) Send the applicant’s other signed original of FAA Form 8610-2, the test planning sheet, and the PBR to the managing FAA office within 7 calendar-days. The managing FAA office will forward the file to AFS-760.
(3) When the applicant passes the airman knowledge tests, the applicant may present the computerized AKTR(s) along with an original of FAA Form 8610-2 to the nearest FAA office or an appropriately rated DME. At that time, an FAA Form 8060-4 will be issued with the appropriate ratings. The applicant must complete and sign the “APPLICANT’S CERTIFICATION” area. The “APPLICANT’S CERTIFICATION” area and the “FAA INSPECTOR’S REPORT” area are the only entries required. AFS-760 is aware of testing procedures for applicants under § 65.80. Provide the applicant with a copy of the original FAA Form 8610-2 (for use in case the certification file is lost).
Continue reading ↓ 120 of 804 passages shown