Radar Vectors
FAA Order Cancelled Issued Jul 25, 2005 AFS-420 53 pages Copy saved Nov 18, 2026

Order 8260.53 Standard Instrument Departures that Use Radar Vectors to Join RNAV Routes

This document is cancelled. Cancelled by 8260.58A. Check the official source before relying on it.

Official source ↗ Open PDF

Distribution: A-W(AS/ND/AT/AF/FS)-3; AVN-100 (200 cys); AMA-200 (80 cys); Initiated by: AFS-420 A-X(FS/AF/AT/AS)-3; ZVS-827; and Special Military and Public Addressees

ORDER

8260. 53

STANDARD INSTRUMENT DEPARTURES

THAT USE RADAR VECTORS TO

JOIN RNAV ROUTES

July 25, 2005

U. S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

FEDERAL AVIATION ADMINISTRATION

RECORD OF CHANGES

CHANGE SUPPLEMENTS CHANGE SUPPLEMENTS

TO OPTIONAL USE TO OPTIONAL USE BASIC BASIC

FAA Form 1320-5 SUPERSEDES PREVIOUS EDITION

Page i (and ii)

FOREWORD This order provides the criteria to evaluate the use of radar vectors to join the initial departure fix (IDF) of an area navigation (RNAV) standard instrument departure (SID). This document is to be used in conjunction with the latest editions of Orders 8260.3, United States Standard for Terminal Instrument Procedures (TERPS); 8260.44, Civil Utilization of Area Navigation (RNAV) Departure Procedures; and 8260.46, Departure Procedure (DP) Program. Area navigation offers significant advantages in establishing routes for departures. However, due to difficulties in implementation, there was a moratorium on developing new RNAV SIDs during 2003 and part of 2004. Radar vectoring affords the flexibility of routing and allows an aircraft to attain sufficient altitude/distance to achieve a satisfactory navigation solution prior to using RNAV. Signed by John M. Allen James J. Ballough Director, Flight Standards Service

FAA Form 1320-5 SUPERSEDES PREVIOUS EDITION

Page iii

TABLE OF CONTENTS Page STANDARD INSTRUMENT DEPARTURES THAT USE

RADAR VECTORS TO JOIN RNAV ROUTES 1.0 Purpose -----------------------------------------------------------------------------------1 2.0 Distribution -------------------------------------------------------------------------------2 3.0 Effective Date-----------------------------------------------------------------------------2 4.0 Background ------------------------------------------------------------------------------2 5.0 Definitions ---------------------------------------------------------------------------------2 5.1 Along-Track (ATRK) Fix Displacement Tolerance ( FDT)---------------------2 5.2 Area Navigation (RNAV)---------------------------------------------------------------2 5.3 Climb Gradient (CG)--------------------------------------------------------------------2 5.4 Cross Track (XTRK) FDT--------------------------------------------------------------3 5.5 Departure End of Runway (DER) ---------------------------------------------------3 5.6 Departure Altitude -----------------------------------------------------------------------3 5.7 Departure Procedure Termination

TABLE OF CONTENTS Page STANDARD INSTRUMENT DEPARTURES THAT USE

Fix----------------------------------------------3 5.8 Distance of Turn Anticipation (DTA) ------------------------------------------------3 5.9 DME/DME Navigation ------------------------------------------------------------------3 5.10 Fix Displacement Tolerance (FDT) -------------------------------------------------3 5.11 Fly-By Waypoint -------------------------------------------------------------------------3 5.12 Fly-Over Waypoint ----------------------------------------------------------------------3 5.13 Global Navigation Satellite System (GNSS)--------------------------------------3 5.14 Global Positioning System (GPS) ---------------------------------------------------4 5.15 Inertial Reference Unit (IRU) ---------------------------------------------------------4 5.16 Initial Climb Area (ICA)-----------------------------------------------------------------4 5.17 Initial Departure Fix (IDF)--------------------------------------------------------------4 5.18 Obstacle Areas and Surfaces --------------------------------------------------------4 5.18.1 Obstacle Evaluation Area

(OEA) or Obstacle Clearance Area (OCA)-----4 5.18.2 Obstacle Clearance Surface (OCS) ------------------------------------------------4 5.18.3 Obstacle Identification Surface (OIS) ----------------------------------------------4 5.19 Pilot Navigation Area (PNA) ----------------------------------------------------------5 5.20 Radar Vector Area ----------------------------------------------------------------------5 5.21 Required Navigation Performance (RNP)-----------------------------------------5 5.22 RNAV Minimum Reception Altitude (MRA) ---------------------------------------5 5.23 RNAV Route ------------------------------------------------------------------------------5 5.24 Standard Instrument Departure (SID) ----------------------------------------------5 5.25 TERPS -------------------------------------------------------------------------------------5 5.26 Waypoint (WPT) -------------------------------------------------------------------------5 5.27 Waypoint Displacement Area/Fix Displacement Area -------------------------6 6.0

General-------------------------------------------------------------------------------------6 6.1 Procedure Identification----------------------------------------------------------------7 6.2 Initial Departure Fix (IDF)--------------------------------------------------------------7 6.2.1 Placement ---------------------------------------------------------------------------------7 6.2.2 SID Limited to One Initial Departure Fix -------------------------------------------7 6.2.3 Maximum Intercept Angle -------------------------------------------------------------7 6.3 RNAV Minimum Reception Altitudes ----------------------------------------------8 6.3.1 GPS, GNSS, or DME/IRU Minimum Reception Altitude-----------------------8

Page iv

TABLE OF CONTENTS (Continued) Page 6.3.2 DME/DME RNAV Minimum Reception Altitude (MRA) --------------------------- 8 6.3.3 RNAV MRAs --------------------------------------------------------------------------------- 8 6.3.4 Altitude for Each Subsequent Segment----------------------------------------------- 8 6.4 Climb Gradient ------------------------------------------------------------------------------ 8 6.5 SID Overview -------------------------------------------------------------------------------- 8 6.5.1 Radar Vector Area-------------------------------------------------------------------------- 8 6.5.2 Pilot Navigation Area ---------------------------------------------------------------------- 8 6.5.3 RNAV Route --------------------------------------------------------------------------------- 8 7.0 Radar Vector Area (RVA)----------------------------------------------------------------10 7.1 Alignment ------------------------------------------------------------------------------------10 7.2 Area

-------------------------------------------------------------------------------------------10 7.3 Obstacle Clearance -----------------------------------------------------------------------10 7.3.1 Radar Departure Inclined Obstacle Evaluation Surfaces------------------------10 7.3.2 Radar Departure Level Obstacle Clearance Surface-----------------------------11 7.3.3 Mitigating Obstacle Penetrations ------------------------------------------------------11 7.3.4 Lateral Obstacle Clearance Below MVA/MIA---------------------------------------11 7.3.5 Vectoring Prohibited Areas--------------------------------------------------------------12 7.3.6 Vectoring Within a Designated Boundary -------------------------------------------13 7.3.7 Obstacle Evaluation for Vectoring Within a Designated Boundary -----------14 7.3.8 Height of the OIS or OCS at the Runway/ICA Boundary ------------------------15 7.4 RVA Altitude --------------------------------------------------------------------------------16 7.5 Minimum Distance-------------------------------------------------------------------------16

7.6 Climb Gradient -----------------------------------------------------------------------------16 7.6.1 CG Calculations to Mitigate a Penetration of the Inclined OIS-----------------17 7.6.2 CG for the ICA and Straight-Ahead Portion of Climb-----------------------------17 7.6.3 CG for Use after the Initial Climb to the First Turn Altitude ---------------------20 8.0 Pilot Navigation Area (PNA) ------------------------------------------------------------22 8.1 Alignment ------------------------------------------------------------------------------------22 8.1.1 Sector Size ----------------------------------------------------------------------------------22 8.1.2 Alignment of DER and PNA-------------------------------------------------------------23 8.2 Area -------------------------------------------------------------------------------------------23 8.2.1 PNA -------------------------------------------------------------------------------------------23 8.2.2 PNA Obstacle Evaluation Area---------------------------------------------------------24 8.2.3 PNA Buffer Area

---------------------------------------------------------------------------25 8.2.4 IDF Turn Area ------------------------------------------------------------------------------26 8.3 Obstacle Clearance -----------------------------------------------------------------------29 8.3.1 PNA Inclined Obstacle Evaluation Surfaces----------------------------------------29 8.3.2 PNA Level Obstacle Clearance Surface---------------------------------------------30 8.3.3 Mitigating Obstacle Penetrations ------------------------------------------------------30 8.4 PNA Altitude --------------------------------------------------------------------------------30 8.4.1 PNA Minimum Altitude -------------------------------------------------------------------30 8.4.2 PNA Boundary Minimum Crossing Altitude -----------------------------------------31 8.5 Minimum Distance/Maximum CG from DER to the PNA Boundary ----------31 8.5.1 CG Calculation -----------------------------------------------------------------------------31 8.5.2 CG Calculation to be

Published--------------------------------------------------------32 8.5.3 Flight Track Distance to the PNA------------------------------------------------------32 8.6 Climb Gradient -----------------------------------------------------------------------------32

Page v (and vi)

TABLE OF CONTENTS (Continued) Page 8.6.1 CG from DER to PNA Boundary-------------------------------------------------------- 32 8.6.2 CG from PNA Boundary to the IDF ---------------------------------------------------- 32 8.6.3 CG to Mitigate a Penetration of the PNA Inclined OCS--------------------------- 33 8.6.4 CG to Mitigate a Penetration of the PNA OIS for Obstacles Within the Extended ICA Splay When the PNA OIS Continues from the RVA OIS/OCS -------------------------------------------------------------------------------------- 34 8.6.5 CG to Mitigate a Penetration of the PNA OIS for Obstacles Outside the Extended ICA Splay When the PNA OIS Continues from the RVA OCS 34 8.6.6 CG to Mitigate a Penetration of the PNA OIS When the OIS Originates at the Height of the RVA Level OCS ------------------------------------ 36 8.6.7 End of PNA Inclined Obstacle Surface and CG Evaluation---------------------- 38 9.0 RNAV Route --------------------------------------------------------------------------------- 38 9.1 Alignment

------------------------------------------------------------------------------------- 38 9.2 Area -------------------------------------------------------------------------------------------- 39 9.3 Obstacle Clearance ------------------------------------------------------------------------ 39 9.3.1 MCA Inclined Obstacle Clearance Surface ------------------------------------------ 40 9.3.2 RNAV Route Level Obstacle Clearance Surface----------------------------------- 40 9.3.3 Obstacle Measurements------------------------------------------------------------------ 41 9.4 RNAV Route Altitude ---------------------------------------------------------------------- 42 9.4.1 RNAV Route Minimum Altitude --------------------------------------------------------- 42 9.4.2 Minimum Crossing Altitude--------------------------------------------------------------- 43 10.0 Coordination, Documentation, and Processing ------------------------------------- 43 11.0 Information Update------------------------------------------------------------------------- 43

Par 1.0 Page 1

STANDARD INSTRUMENT DEPARTURES THAT USE

STANDARD INSTRUMENT DEPARTURES THAT USE

RADAR VECTORS TO JOIN RNAV ROUTES

1.0 PURPOSE.

This order provides the criteria to evaluate the use of radar vectors to join the initial departure fix (IDF) of an RNAV standard instrument departure (SID). As a matter of operational necessity, Air Traffic (AT) may require the use of radar vectors to pre-position departing aircraft prior to authorizing area navigation (RNAV) (see figure 1). This order is to be used in conjunction with the latest editions of Orders 8260.3, United States Standard for Terminal Instrument Procedures (TERPS); 8260.44, Civil Utilization of Area Navigation (RNAV) Departure Procedures; and 8260.46, Departure Procedure (DP) Program.

RADAR VECTORS TO JOIN RNAV ROUTES

Figure 1. Radar Vectors to Join RNAV Routes

RADAR VECTORS

RADAR VECTORS

RADAR VECTORS

RADAR VECTORS

INITIAL DEPARTURE FIX

RNAV ROUTE

RADAR VECTORS

Page 2 Par 2.0

2.0 DISTRIBUTION.

This order is distributed in Washington Headquarters to the branch level in the Offices of Airport Safety and Standards and Communications, Navigation, and Surveillance Systems; Air Traffic, Airway Facilities, and Flight Standards Services; to the National Flight Procedures Office and the Regulatory Standards Division at the Mike Monroney Aeronautical Center; to branch level in the regional Flight Standards, Airway Facilities, Air Traffic, and Airports Divisions; special mailing list ZVS-827, and to Special Military and Public Addressees. 3.0 EFFECTIVE DATE. September 1, 2005 4.0 BACKGROUND. RNAV operations offer significant advantages in establishing routes for departures. However, due to difficulties in implementation, there was a moratorium on developing new RNAV SIDs during 2003 and part of 2004. Radar vectoring affords flexibility of routing and allows an aircraft to attain sufficient altitude/distance to achieve a satisfactory navigation solution prior to using RNAV. 5.0 DEFINITIONS.

RADAR VECTORS

NOTE: Additional definitions and explanations are in Orders 8260.3, Volume 4; 8260.44; and in the Aeronautical Information Manual (Pilot/Controller Glossary). 5.1 ALONG-TRACK (ATRK) Fix Displacement Tolerance (FDT). The FDT measured along the designated flight track (see paragraph 5.10). 5.2 AREA NAVIGATION (RNAV). RNAV operations provide enhanced navigational capability to the pilot. RNAV equipment can compute the airplane position, actual track and ground speed, and then provide meaningful information relative to a route of flight selected by the pilot. Typical RNAV equipment will provide the pilot with distance, time, bearing, and cross-track error relative to the selected “TO” or “active” waypoint (WP) and the selected route. Several navigational systems with different performance characteristics are capable of providing area navigational functions. Present day RNAV includes inertial navigation system (INS), distance measuring equipment (DME/DME), global positioning system (GPS), and wide area augmentation system (WAAS). Modern multi-sensor systems can integrate one or more of the above sensors/systems to provide a more accurate and reliable navigational system. Due to the different levels of performance, the wide range of RNAV capabilities can provide diverse airspace solutions incorporating different levels of lateral obstacle clearance protection. 5.3 CLIMB GRADIENT (CG). Aircraft climb requirement expressed in feet per nautical mile (NM) or percentage; i.e. 200 ft/NM or 3.29% (see paragraphs 7.6 and 8.6).

Par 5.4 Page 3

5.4 CROSS-TRACK (XTRK) FDT. The FDT measured perpendicular left or right of the designated flight track (see paragraph 5.10). 5.5 DEPARTURE END OF RUNWAY (DER). The end of the area declared suitable for takeoff. 5.6 DEPARTURE ALTITUDE.

An altitude at the end of the departure evaluation area that satisfies the requirements for en route operations or for off route/off airway operations. 5.7 DEPARTURE PROCEDURE TERMINATION FIX. The fix that ends the RNAV SID route, and may be located either within the en route structure or outside the en route structure (using transitions to enter the en route structure). 5.8 DISTANCE OF TURN ANTICIPATION (DTA).

A distance preceding a fly-by waypoint (WP) at which an aircraft is expected to start a turn to intercept the course/track of the next segment. 5.9 DME/DME NAVIGATION. The use of distance measuring equipment (DME) facilities for navigation. 5.10 FIX DISPLACEMENT TOLERANCE (FDT). The FDT is the largest distance from the plotted position of a waypoint/fix

for an aircraft attempting to fly over the waypoint/fix considering all system error components. (Also see Waypoint Displacement Area/Fix Displacement Area, ATRK, and XTRK.) See paragraphs 5.1 and 5.4. 5.11 FLY-BY WAYPOINT. A waypoint where a turn is initiated prior to reaching the fix/waypoint. 5.12 FLY-OVER WAYPOINT. A waypoint over which an aircraft is expected to fly before the turn is initiated. 5.13 GLOBAL NAVIGATION SATELLITE SYSTEM (GNSS). The GNSS is a worldwide position and time determination system, which includes one or more satellite constellations, aircraft receivers, and system integrity monitoring. GNSS is augmented as necessary to support the required navigation performance for the actual phase of operation. The U.S. GNSS is the Global Positioning System.

Page 4 Par 5.14

5.14 GLOBAL POSITIONING SYSTEM (GPS). GPS is a U. S. satellite-based radio navigational, positioning, and time transfer system operated by the Department of Defense (DOD). The system provides highly accurate position and velocity information and precise time on a continuous global basis to an unlimited number of properly equipped users. 5.15 INERTIAL REFERENCE UNIT (IRU). Airborne equipment that can be used for navigation even during periods without sensor inputs. An IRU uses gyros and the previous sensor inputs, or ground reference points, to dead reckon until regaining sensor reception. 5.16 INITIAL CLIMB AREA (ICA). An area beginning at the DER to provide unrestricted climb to at least 400 ft above DER elevation. 5.17 INITIAL DEPARTURE FIX (IDF). The first published fix/waypoint used for the departure. In this order, the IDF denotes the beginning of the RNAV portion of the SID. NOTE: IF is used for coding (per ARINC 424) of the IDF. The “IF” acronym is also used in conjunction with the intermediate fix of an instrument approach procedure. 5.18 OBSTACLE AREAS AND SURFACES.

5.18.1 Obstacle Evaluation Area (OEA) or Obstacle Clearance Area (OCA). The area, defined by criteria, that is evaluated for obstacles. 5.18.2 Obstacle Clearance Surface (OCS). A surface within the OEA/OCA where obstacle penetrations are not allowed. The OCS may be either an inclined surface or a flat surface. The required obstruction clearance (ROC) (sometimes referred to as required obstacle clearance) is the difference between the OCS and the lowest planned aircraft altitude. 5.18.3 Obstacle Identification Surface (OIS). An OIS is the surface within the OEA/OCA where the surface is not required to clear obstacles, but the more prominent obstacles must be mitigated or identified for use in aircrew planning and operation. An example of mitigation of an OIS penetration is establishing a minimum climb gradient to raise the OCS above an obstacle. An example where the more prominent obstacles that penetrate an OIS must be identified for use in aircrew planning and operation is the initial climb area for the first 200 ft of climb after takeoff.

Par 5.18.3 Page 5

NOTE: The terms OIS and OCS are sometimes used interchangeably. As used in this document, they are not interchangeable; they differ in regard to whether it is allowable to have penetrations of the surface. 5.19 PILOT NAVIGATION AREA (PNA). An area used to transition from radar vectoring to the area navigation route. The PNA is bounded by two lines, represented by the maximum intercept courses leading to the IDF, enclosed by an arc of specified radius centered on the IDF (see figure 3 and paragraph 8.0). 5.20 RADAR VECTOR AREA (RVA). The area in which radar vectors are provided. The RVA extends from the runway(s) to the PNA arc boundary (see figure 3 and paragraph 7.0). 5.21 REQUIRED NAVIGATION PERFORMANCE (RNP). A statement of the required navigational performance for operation within a defined airspace. Note that there may be additional requirements beyond accuracy applied to a particular RNP level. 5.22 RNAV MINIMUM RECEPTION ALTITUDE (MRA). The minimum altitude required to form an RNAV solution. This is based on the

minimum height/altitude that aircraft systems can begin RNAV operations, that flight procedures allow the use of RNAV, and that available sensors can generate an RNAV solution. The RNAV MRA depends on the navigation source required for the SID (see paragraph 6.3). 5.23 RNAV ROUTE. The RNAV route begins at the IDF and contains all subsequent segments including transitions (see figure 3 and paragraph 9.0). 5.24 STANDARD INSTRUMENT DEPARTURE (SID). A preplanned IFR ATC departure procedure printed in graphic form for pilot/controller use to provide obstacle clearance and a transition from the terminal area to the appropriate en route structure. SIDs are primarily designed for system enhancement to expedite traffic flow and to reduce pilot/controller workload. ATC clearance must be received prior to flying a SID. 5.25 TERPS. Order 8260.3, United States Standard for Terminal Instrument Procedures. 5.26 WAYPOINT (WPT). An RNAV fix defined in terms of latitude/longitude coordinates. Waypoints are used to establish beginning and ending points of RNAV departure route segments.

Page 6 Par 5.27

5.27 WAYPOINT DISPLACEMENT AREA/FIX DISPLACEMENT AREA. The rectangular area formed around and centered on the plotted position of a waypoint/fix. This describes the region in which the aircraft could be placed when attempting to fly over the waypoint considering all system error components. Its dimensions are plus-and-minus the appropriate along-track and cross-track fix displacement tolerance values. (Also see Fix Displacement Tolerance.) 6.0 GENERAL.

When a SID begins with radar vectors, it may serve one or more runways at single or multiple airports. En route transitions are permitted. However, transitions must not originate at the IDF. A single RNAV course must be defined from the IDF. Terminate the basic DP at or beyond the first WP encountered after the IDF. Establish the termination fix within the en route structure OR, provide a transition(s) from the termination fix to the en route structure (see figure 2).

Par 6.0 Page 7

Figure 2. RNAV Route

INITIAL DEPARTURE

INITIAL DEPARTURE

FIX

DP TERMINATION

FIX

TRANSITION

TRANSITION

TRANSITION

RECIPROCAL RNAV OUTBOUND

COURSE

MAX

45°

MAX

45°

INTERCEPT

INTERCEPT

6.1 PROCEDURE IDENTIFICATION. See Order 8260.46, appendix 2. 6.2 INITIAL DEPARTURE FIX (IDF). The IDF must be a fly-by waypoint. A track to fix (TF) leg must follow the IDF. 6.2.1 Placement. Locate the IDF within the distance requirements outlined in paragraphs 7.0 and 8.0. Coordinate the location of the IDF with Air Traffic. 6.2.2 SID Limited to One Initial Departure Fix. Each SID is limited to one IDF. Where more than one IDF is required, an additional SID(s) must be developed. 6.2.3 Maximum Intercept Angle. The maximum intercept angle to join the IDF is ± 45° relative to the reciprocal of the RNAV course outbound from the IDF (see figure 2).

RECIPROCAL RNAV OUTBOUND

Page 8 Par 6.3

6.3 RNAV MINIMUM RECEPTION ALTITUDES. 6.3.1 GPS, GNSS, or DME/IRU RNAV Minimum Reception Altitude. To establish the MINIMUM RNAV reception altitude for SIDs that require GPS, or GNSS, or IRU, use no less than the designated height above the DER elevation. That height will be 2,000 ft for Type A procedures or 500 ft for Type B procedures. 6.3.2 DME/DME RNAV Minimum Reception Altitude (MRA).

To establish the MINIMUM RNAV reception altitude for SIDs that authorize DME/DME, use no less than 2,000 ft above the DER or the computer model predicted altitude, whichever is higher. The computer model prediction is subsequently verified through flight inspection. 6.3.3 RNAV MRAs will be rounded up (not rounded down). Typical rounding is to the next higher 100-ft (MSL) increment.

NOTES: 1. The RNAV MRA based on DME/DME inputs is usually higher than the RNAV MRA based on GPS/GNSS inputs or the use of IRU. 2. The RNAV MRA is location specific; the RNAV MRA might be higher at location X than at location Y. 3. The RNAV MRA denotes the availability of PCG. 4. See paragraphs 7 through 9 for additional factors that apply to establishing altitudes. 6.3.4 The altitude for each subsequent segment of the departure must be at or above the altitude of the previous segment, even if the subsequent segment would qualify for a lower altitude due to lower MRA and lower obstacles/terrain. 6.4 CLIMB GRADIENT. Climb gradients are used in this order for either obstacle clearance or to reach the RNAV MRA or an ATC required altitude. Gradients in excess of 200 ft per NM are to be submitted for publication. When a climb gradient is required in order to reach the RNAV MRA, submit that climb gradient for publication as an ATC climb gradient, not an obstacle climb gradient. If there is a requirement for both an obstacle climb gradient and an ATC climb gradient, always publish the obstacle climb gradient. Publish the ATC climb gradient when it is higher than the obstacle climb gradient. 6.5 SID OVERVIEW. A SID incorporating radar vectors to join RNAV (see figure 3) is comprised of: 6.5.1 A radar vector area (see paragraph 7.0), 6.5.2 A pilot navigation area (see paragraph 8.0), and 6.5.3 An RNAV route (see paragraph 9.0).

Par 6.5.3 Page 9

Figure 3. SID Overview

DER MUST BE INSIDE THIS LINE

MAXIMUM INTERCEPT

MAXIMUM INTERCEPT

DER MUST BE INSIDE THIS LINE

INITIAL DEPARTURE

FIX

RVA

PNA

PNA ARC

PNA

RVA

RVA

RVA

RVA

RVA

RNAV ROUTE

Page 10 Par 7.0

7.0 RADAR VECTOR AREA (RVA). Radar systems authorized to vector departing IFR aircraft may be used to vector to RNAV routes. 7.1 ALIGNMENT.

RNAV ROUTE

The radar area and the RNAV route must be aligned in a manner that meets the RNAV intercept requirements (± 45°). See paragraph 6.2. 7.2 AREA.

The obstacle evaluation area is the area available for radar vectoring for the SID. NOTE: The area and minimum vectoring altitudes/minimum IFR altitudes (MVAs/MIAs), intended for radar vectoring to RNAV routes, are determined by Air Traffic and should be in the procedure request. 7.3 OBSTACLE CLEARANCE. For each runway used in the SID, evaluate the RVA using an inclined obstacle surface and a level obstacle surface (see figure 4).

Figure 4. Departure Obstacle Evaluation Surfaces

RUNWAY

DER

40:1 OIS

MVA/MIA

ROC USED FOR RADAR

ROC USED FOR RADAR

ROC DEPARTURE

LEVEL OCS

IF OBSTACLE PENETRATES INCLINED OIS -

MITIGATION

REQUIRED

FOR OBSTACLES

BELOW BOTH

SURFACES - NO MITIGATION

REQUIRED

IF OBSTACLE PENETRATES

LEVEL OCS -

MITIGATION

REQUIRED 7.3.1 Radar Departure Inclined Obstacle Evaluation Surfaces. The purpose of an inclined (also called sloping or rising) obstacle identification surface or obstacle clearance surface is to ensure obstacle clearance for aircraft that are climbing. Because the evaluation uses a rising surface, procedures developed on the basis of this evaluation must not restrict the aircraft’s climb until reaching the MVA/MIA.

LEVEL OCS -

Par 7.3.1a Page 11

7.3.1 a. The departure inclined obstacle identification surface rises at 40:1 from the DER, ICA baseline, runway, or from the edge of the initial climb area. For each runway authorized for the departure, evaluate for diverse departure as specified in Order 8260.3, Volume 4, chapter 2. Terminate the 40:1 OIS upon reaching the departure level OCS. When the inclined 40:1 OIS does not reach the departure level OCS in the RVA, continue the inclined 40:1 OIS evaluation in to the PNA. 7.3.1 b. The departure inclined obstacle clearance surface is used if obstacles penetrate the 40:1 OIS. Determine an OCS, at a steeper slope than the OIS, which will clear obstacles. See paragraphs 7.3.3 and 7.6 and figure 5. 7.3.2 Radar Departure Level Obstacle Clearance Surface.

The purpose of the departure level OCS is to ensure obstacle clearance if the aircraft have to level off at the MVA/MIA. The level OCS is at an elevation equal to the MVA/MIA minus the ROC. The ROC is specified in applicable FAA directives used for developing MVAs/MIAs. 7.3.3 Mitigating Obstacle Penetrations.

If the 40:1 OIS is clear, departures are authorized in any direction from the evaluated runway and no further TERPS action is required (see figures 4 and 5). If the inclined OIS/OCS has obstacle penetrations, use the obstacle-avoidance methods described in Order 8260.3, Volume 4, and Order 8260.46, Departure Procedure (DP) Program, table 1, to mitigate the penetration(s), with the intended goal of retaining standard takeoff minimums and standard climb gradients to the extent possible.

Figure 5. Mitigating Obstacle Penetrations

7.3.4 Lateral Obstacle Clearance Below MVA/MIA.

If Air Traffic requests evaluation of an area(s) for vectoring below the MVA/MIA, provide data on any obstacle(s) that penetrates the OCS to allow appropriate buffers. 7.3.4 a. The buffer distance, 3 or 5 NM, for vectoring below an MVA/MIA is the same as the buffer distance for MVA/MIA chart sectors.

Page 12 Par 7.3.4b

7.3.4 b. The buffer area may be reduced, near the departure runway, using the splay defined in Order 8260.3, Volume 4, paragraph 2.2, for the initial assigned heading(s). Note that the splay, as described and illustrated in TERPS paragraph 2.2, extends from the departure reference point (DRP), or from the ICA, or from the outer boundary radius of the first turn. The splay provides at least 20 degrees separation between the assigned initial headings and penetrating obstacles. One example is the vectoring prohibited area 1 in figure 6. Another example is the initial portion of the obstacle evaluation area in figure 8. 7.3.4 c. The inclined OIS originates from the ICAB, the runway, and the ICA. It extends upward within the vectoring areas and the buffer areas until reaching the level OCS associated with the MVA/MIA. 7.3.5 Vectoring Prohibited Areas. 7.3.5 a. A vectoring prohibited area/sector is used to laterally avoid the penetrating obstacle(s) (see figure 6). Boundaries of any vectoring prohibited area/sector must provide at least the buffer distance, described in para- graph 7.3.4, from all penetrating obstacle(s). Additional guidance is in Order 8260.3, Volume 4, paragraphs 2.2 and 2.3.

Figure 6. Example of Vectoring Prohibited Areas

AREA WITH OBSTACLES THAT PENETRATE 40:1 OIS

VECTORING PROHIBITED

AREA 3

VECTORING PROHIBITED

AREA 1

VECTORING PROHIBITED

AREA 2

VECTORING

AREA

VECTORING

AREA

ALLOW FOR AIRCRAFT TURN RADIUS

IN EVERY DIRECTION

WHERE TURNS ARE

AUTHORIZED

WHERE TURNS ARE

VECTORING

AREA

15°

15°

ICA +500’

20°

DRP

REQUIRES

BUFFER DISTANCE

SPLAY REQUIRED

FROM OBSTACLE

MAXIMUM AUTHORIZED

INITIAL HEADING IS PARALLEL TO 20° SPLAY

OBSTACLE THAT

PENETRATES

40:1 OIS

REQUIRES

BUFFER DISTANCE

VECTORING

AREA

Par 7.3.5b Page 13

7.3.5 b. To allow enough distance for aircraft to turn prior to a vectoring prohibited area/sector, the distance between the ICA and the boundary of a vectoring prohibited area/sector, must be equal to or greater than an aircraft turn distance. Use a turn distance based on the “Outer Boundary Radius” in Order 8260.3, Volume 4, chapter 3, table 3-2. This minimum distance requirement does not apply to sectors used for the initial heading(s) from the runway. For example, in figure 6 the minimum distance requirement does not apply to vectoring prohibited area 1; but it does apply between the ICA and the boundary of vectoring prohibited areas 2 and 3. 7.3.6 Vectoring Within a Designated Boundary. When requested by air traffic, evaluate a radar departure vectoring area/sector for obstacle clearance. The designated boundary must provide the obstacle clearance buffer distance from penetrating obstacles. The designated boundary may be moved further away from penetrating obstacles, for reasons such as air traffic flow, airspace, or environmental needs, but must not be moved closer than the buffer distance. See figure 7 for an example area.

BUFFER DISTANCE

Figure 7. Vectoring Within a Boundary to Reach MVA/MIA

DER

OBSTACLE CONSTRAINTS

OBSTACLE CONSTRAINT

OBSTACLE CONSTRAINTS 3 OR 5 NM BUFFER

3 OR 5 NM BUFFER

POSSIBLE BOUNDARY

BASED ON OBSTACLE

CLEARANCE ONLY

DESIGNATED BOUNDARY

BASED ON OTHER CONSTRAINTS

ICA

DESIGNATED BOUNDARY

DESIGNATED BOUNDARY

DESIGNATED BOUNDARY

VECTORING

AREA

VECTORING

AREA

D

ES

IG

NAT

ED

BOU

NDA

RY

Page 14 Par 7.3.7

7.3.7 Obstacle Evaluation for Vectoring Within a Designated Boundary. The obstacle evaluation area for a radar departure vectoring area/sector includes a buffer beyond the designated boundary of the vectoring area (see figure 8). Use the buffer distance described in paragraph 7.3.4.

Figure 8. OEA for Vectoring Within a Boundary to Reach MVA/MIA

DER

DER

20°

20°

DRP

DRP

OBSTACLE CONSTRAINTS

OBSTACLE CONSTRAINTS

OBSTACLE CONSTRAINT

OBSTACLE CONSTRAINTS

POSSIBLE BOUNDARY

BASED ON OBSTACLE

CLEARANCE ONLY

DESIGNATED BOUNDARY

BASED ON OTHER CONSTRAINTS

ICA

DESIGNATED BOUNDARY

DESIGNATED BOUNDARY

VECTORING

AREA

VECTORING

AREA

D

ES

IG

NAT

ED

BOU

NDA

RY

3 OR 5 NM BUFFER

3 OR 5 NM BUFFER

3 OR 5 NM BUFFER

3 OR 5 NM BUFFER

3 OR 5 NM BUFFER

3 OR 5 NM BUFFER

3 OR 5 NM BUFFER

ICA

DESIGNATED BOUNDARY

DESIGNATED BOUNDARY

RANGE OF INITIAL HEADINGS

3 OR 5 NM BUFFER

OBSTACLE EVALUATION AREA

OBSTACLE EVALUATION

AREA

OBSTACLE EVALUATION

AREA

Par 7.3.8 Page 15

7.3.8 Height of the OIS or OCS at the Runway/ICA Boundary. 7.3.8 a. For an initial climb to 400 ft, the height of the OIS or OCS at the ICA end is 303.81 ft above the DER elevation.

OBSTACLE EVALUATION

Figure 9. Height of ICA Obstacle Clearance Surface - Profile View

DER

RUNWAY

TURN ALTITUDE

HEIGHT OF OIS/OCS AT END OF ICA

E

CLIMB GRADIENT

OIS/OCS

ICA LENGTH

ROC

7.3.8 b. When climbing to an altitude higher than 400 ft above the DER, calculate the height of the OIS or OCS (HOCS) at the end of the ICA (see figure 9), based on the turn altitude, as follows:

ICA LENGTH

HOCS = ((Turn Altitude - E) X .76) + E Where:

HOCS = Height (MSL) of the origin, at end of ICA, for OIS/OCS measurements Turn Altitude = Lowest altitude authorized for the first turn after departure DERe = Departure end of runway (DER) elevation E = Origin starting elevation, at DER/ICAB. Use DERe for ICA calculations. ICAB = Initial Climb Area Baseline NOTES: 1. Use this formula where the initial climb is to an altitude rather than a fix or distance. 2 If various turn altitudes are allowed, use the lowest altitude for this calculation. When a specific turn altitude is not assigned, use DERe + 400 ft.

3. For the value “.76,” in the departure obstacle surface formulas, you may substitute a value with a greater number of digits; for example, you may substitute “.7595” or “.759514435” for the “.76.”

4. DOD procedures may use the DOD option in Order 8260.3, Volume 4, paragraph 1.4.1, as follows: HOCS = Turn Altitude – ROC, Where ROC = 48 X length of ICA, Where length of ICA = (Turn Altitude – E) / CG. 5. If the ICA OIS has penetrations of 35 ft or less, also use Order 8260.3, Volume 4, paragraph 1.3, and applicable policy letters. Note that the applicable policy letters, and paragraph 1.3, as modified, address using a runway length reduction rather than an origin increase as allowed by the earlier (superseded) criteria.

Page 16 Par 7.3.8b

Figure 10. Height of Obstacle Clearance Surface - Cross Section View

40:1 OCS

40:1 OCS

MVA/MIA MVA/MIA

MVA/MIA MVA/MIA

ROC ROC

DEPARTURE LEVEL SURFACE OCS DEPARTURE LEVEL SURFACE OCS

CROSS SECTION VIEW

IF OBSTACLE PENETRATES INCLINED OCS -

MITIGATION

REQUIRED

IF OBSTACLE PENETRATES INCLINED OCS -

MITIGATION

REQUIRED

FOR OBSTACLES

BELOW BOTH

SURFACES - NO MITIGATION

REQUIRED

FOR OBSTACLES

BELOW BOTH

BELOW BOTH

SURFACES - NO MITIGATION

REQUIRED

IF OBSTACLE PENETRATES

LEVEL OCS -

MITIGATION

REQUIRED

IF OBSTACLE PENETRATES

LEVEL OCS -

MITIGATION

REQUIRED

ICA

HOCS HOCS

ICA BOUNDARY

Aircraft turning

right Aircraft turning

left

7.3.8 c. For evaluating “diverse A area” obstacles, use the height of the OIS/OCS (HOCS) at the ICA end (MSL) as the origin elevation at the ICA boundary (see figure 10). The “diverse A area” is based on Order 8260.3, Volume 4, para- graph 2.1. It includes obstacles to the side of the runway, to the side of the ICA, or beyond the ICA and outside of the ICA splay.

ICA BOUNDARY

NOTE: This order modifies the “diverse A area” to exclude the extended splay area, which is grouped with the ICA in order to base the CG calculations from the DER/ICAB rather than the end of the ICA. 7.3.8 d. For evaluating “diverse B area” obstacles, the OIS/OCS origin elevation, at the DRP, is at least 400 ft above the airport elevation. If the turn altitude is higher than 400 ft above the airport elevation, the “diverse B area” origin elevation equals the turn altitude (MSL). See figure 10. The “diverse B area” is determined using Order 8260.3, Volume 4, paragraph 2.1 and includes obstacles, encountered after turning, that are behind the departure reference line. 7.4 RVA ALTITUDE.

The RVA minimum altitude is the altitude to which aircraft must climb before a

level off is allowed. Plan on the RVA altitude(s) being the applicable MVA/MIA from existing radar procedures, unless Air Traffic requests a redesign. 7.5 MINIMUM DISTANCE. The distance from the DER to the PNA boundary must be sufficient to allow aircraft to reach the PNA minimum altitude (see paragraphs 8.4 and 8.5). 7.6 CLIMB GRADIENT.

Apply the standard climb gradient of 200 ft per NM from Order 8260.3, Volume 4 unless a higher gradient is required by the calculations below. Before implementing a higher than standard CG also consider relocating the IDF and/or the PNA.

Par 7.6.1 Page 17

7.6.1 CG Calculations to Mitigate a Penetration of the Inclined OIS.

The obstacle climb gradient calculation for the inclined OCS depends on the location of the obstacle. For obstacles within the ICA or within the extended splay lines of the ICA (figure 11), use paragraph 7.6.2. For all other obstacles within the OEA, use paragraph 7.6.3. 7.6.2 CG for the ICA and Straight-Ahead Portion of Climb. 7.6.2 a. The evaluation of the straight-ahead portion of the climb extends to the termination of the OIS originating at the DER. 7.6.2 a. (1) The termination altitude of the inclined OIS equals the level OCS, which is in each MVA/MIA sector, the MVA/MIA minus the ROC. 7.6.2 a. (2) The distance (in feet) from the DER to the OIS/OCS termination is calculated by multiplying the OIS/OCS slope times the rise of the OIS/OCS. The rise is the termination altitude minus the origin (DER) elevation.

NOTE: This distance to the OIS/OCS termination will also be used in paragraph 8.6.3.

Page 18 Par 7.6.2a(2)

Figure 11. Inclined OIS Measurements and

Climb Gradient Calculations

DER

20°

20° DRP

BUFFER

ICA

BUFFER

OBSTACLE EVALUATION

OBSTACLE EVALUATION

AREA

APPLY THE “CG AFTER TURN”

FORMULA HERE

APPLY THE “CG AFTER TURN”

FORMULA HERE

APPLY THE “CG AFTER TURN”

FORMULA HERE

APPLY SAME CG FORMULA

AS USED FOR ICA

APPLY CG FORMULAS FROM PARAGRAPH 7.6

UNTIL THE TERMINATION OF THE INCLINED OCS

TERMINATION OF THE INCLINED OCS

OBSTACLE EVALUATION

AREA

DESIGNATED BOUNDARY

DESIGNATED BOUNDARY

DESIGNATED BOUNDARY

EXTENSION OF ICA SPLAY

EXTENSION OF ICA SPLAY

Primary Area Obstacle Clearance Surface 40:1 7.6.2 b. For obstacles within the ICA or within the extended splay lines of the ICA and prior to the termination of the OIS originating at the DER, determine the obstacle clearance climb gradient from the DER/ICAB to an obstacle as follows:

EXTENSION OF ICA SPLAY

CG = O - E .76 D

Where CG = Climb gradient, in ft per NM, that provides the minimum ROC O = Obstacle (MSL) elevation E = CG origin starting (MSL) elevation. Use DERe as the origin elevation for obstacles within the ICA or within the extended splay lines of the ICA. D = Distance (NM) from DER or ICA baseline (ICAB). See figure 12.

NOTES: 1. CG formula is from Order 8260.3, Volume 4, Chapter 1, paragraph 1.4.1. DOD procedures may use the DOD option in paragraph 1.4.1. 2. In addition to obstacles within the ICA, this CG formula also applies to obstacles beyond the ICA that are within the extension of the ICA splay lines

Par 7.6.2b Page 19

and prior to the termination point of the inclined OIS that originates from the DER. See figures 11 and 12 for RVA obstacles. 3. Measurements for obstacle distance (D) for CG calculations are made from the same origin as the measurements for the OIS/OCS calculations. 4. If the CG is required to avoid obstacles within 3 statute miles of the DER, provide ceiling and visibility values as an alternative to the CG. See Order 8260.46, table 1. 5 If the ICA OIS has penetrations of 35 ft or less, use Order 8260.3, Volume 4, paragraph 1.3, and applicable policy letters. Note that the applicable policy letters, and paragraph 1.3 as modified, address using a runway length reduction rather than an origin increase as allowed by the earlier (superseded) criteria. 6. The relationship between OCS and CG is as follows: OCS = 8000 / CG and CG = 8000 / OCS 7. After determining a higher CG or a higher turn altitude (TA), recalculate the ICA length. For an initial climb to an altitude, ICA length equals (TA – E) / CG.

Figure 12. Measurements to Obstacles Within ICA

or Extended Splay Lines

Primary Area Obstacle Clearance Surface 40:1

+500’

7.6.2 c. Determine the “climb to” altitude (CTA) for the CG as follows:

CTA = E + (CG X D)

Where CTA = Climb-to altitude (MSL) for climb gradient termination E = CG origin starting (MSL) elevation. Use DERe for ICA calculations. CG = Climb gradient in feet per NM D = Distance (NM) from DER or ICA baseline (ICAB) to obstacle (see figure 11).

CTA = E + (CG X D)

Page 20 Par 7.6.2c

NOTES: 1. Climb to Altitude formula is from Order 8260.3, Volume 4, paragraph 1.4.2. 2. This CTA is for the ICA and straight ahead climb CG in paragraph 7.6.2a. 3. This formula provides the minimum/optimum CTA for an individual obstacle. For multiple obstacles that require climb gradients, apply Order 8260.3, Volume 4, paragraph 1.4.4, and applicable policy letters.

7.6.3 CG for Use after the Initial Climb to the First Turn Altitude. 7.6.3 a. The evaluation for after the initial climb extends from the ICA, or runway, to the termination of the OIS originating at the ICA/runway. 7.6.3 a. (1) The termination altitude of the inclined OIS equals the level OCS, which is, in each MVA/MIA sector, the MVA/MIA minus the ROC. 7.6.3 a. (2) The distance (in feet) from the ICA/runway to the OIS/OCS termination is calculated by multiplying the OIS/OCS slope times the rise of the OIS/OCS. The rise is the termination altitude minus the origin altitude.

NOTE: This distance to the termination of the inclined OIS will also be used in paragraph 8.6. 7.6.3 b. For obstacles outside the ICA and outside of the extended splay lines of the ICA, determine the obstacle clearance climb gradient from the ICA/runway to an obstacle as follows:

CG = O - E .76 D

Where

CG = Climb gradient in feet per NM O = Obstacle (MSL) elevation E = CG origin starting (MSL) elevation For origin elevation, use the elevation of the OCS at the area A/B origin D = Distance (NM) from the runway or ICA boundary to the obstacle

NOTES: 1. This CG is a variation of Order 8260.3, Volume 4, chapter 1, para- graph 1.4.1. DOD procedures may use the DOD option in paragraph 1.4.1. 2. This “after reaching a turn altitude” formula is based on the aircraft having already accomplished the initial climb, allowing the use of a higher origin. 3. Use this formula with the “diverse A area” origin elevation for obstacles to the side of the runway, or to the side of the ICA, or outside of the extended splay lines of the ICA. Use this formula with the “diverse B area” origin elevation for obstacles behind the departure reference line, as shown in Order 8260.3, Volume 4, paragraph 2.1. 4 Measurements for obstacle distance (D) for CG calculations are made from the same origin as the measurements for the OIS/OCS calculations.

Par 7.6.3c Page 21

7.6.3 c. Determine the “climb to” altitude (CTA) for the “after turn” CG, as follows:

CTA = TA + (CG X D) For a “diverse A area” obstacle CTA = TA + 126 + (CG X D) For a “diverse B area” obstacle

Where

CTA = Climb-to altitude (MSL) for climb gradient termination TA = Turn altitude (the minimum aircraft altitude at the end/side of the ICA) CG = Climb gradient in feet per NM from the ICA/DRP to an obstacle D = Distance (NM) from the runway or ICA boundary to the obstacle

NOTES: 1. “Climb to” altitude formula is a variation of Order 8260.3, Volume 4, paragraph 1.4. 2. Use this CTA formula with the CG calculation in paragraph 7.6.3b. 3 For CTA calculation with a “diverse A area” controlling obstacle, the CG starting (MSL) elevation is the TA. 4. For CTA calculation with a “diverse B area” controlling obstacle, the CG starting (MSL) elevation is the TA plus 126 feet (Note: 126 is based on 96/.76). 5. This formula provides the minimum/optimum CTA for an individual obstacle. For multiple obstacles that require climb gradients, apply Order 8260.3, Volume 4, paragraph 1.4.4, and applicable policy letters.

Page 22 Par 8.0

8.0 PILOT NAVIGATION AREA (PNA).

The PNA is bounded by two lines and an arc (see figure 13). The lines represent

the maximum intercept courses and the arc allows a distance to begin area navigation.

Figure 13. Example of Pilot Navigation Area

INITIAL DEPARTURE

FIX (IDF)

Where = Design Intercept Angle (Maximum of 45°) PNAr = Pilot Navigation Area (PNA) Radius θ

FIX DISPLACEMENT

AREA

RNAV OUTBOUND COURSE

RNAV OUTBOUND COURSE

θ

θ

PNAr

PNAr

PNA

PNA

MAXIMUM INTERCEPT ANGLE

MAXIMUM

INTERCEPT

ANGLE

8.1 ALIGNMENT.

Align the PNA to the RNAV course (paragraph 9.0) outbound from the IDF. Measure the intercept angles from the reciprocal of the RNAV outbound course. 8.1.1 Sector Size. The MINIMUM sector size is 30° (see figure14).

MAXIMUM INTERCEPT ANGLE

Par 8.1.1 Page 23

Figure 14. Examples of Minimum Sector Size for PNA

INITIAL DEPARTURE

FIX

INITIAL DEPARTURE

FIX

RNAV

OUTBOUND COURSE

PNA

PNA

15°

15°

RNAV

OUTBOUND COURSE

PNA

RECIPROCAL

RECIPROCAL

30°

MINIMUM

SECTOR

SIZE 30°

INTERCEPT

ANGLE

INTERCEPT

ANGLE

INTERCEPT

ANGLE

INTERCEPT

OUTBOUND COURSE

ANGLE

8.1.2 Alignment of DER and PNA. To qualify for this type SID, the departure end of each authorized runway must be located within the area formed by the maximum intercept angles extended from the PNA to the extremities of the RVA (see figure 3). When that alignment cannot be met, approval is required from Flight Standards Service. Approval requests need to include documentation of the size of OCA considered and an explanation of how the aircraft will be brought within the maximum intercept angles in sufficient time to turn to the IDF. 8.2 AREA. 8.2.1 PNA. This is the area that is identified to air traffic, as sufficient to start pilot navigation. Construct the PNA centered on the IDF, bounded by the maximum intercept courses, and using the PNA arc radius (PNAr) distance from table 1.

Table 1. Pilot Navigation Area Arc Radius

PNA Altitude and Airspeed

Radius for Level 1

Radius for Level 2

Below 10,000 MSL and At or Below 250 KIAS 6 NM 7 NM

At or Above 10,000 MSL or Above 250 KIAS 9 NM 10 NM

Page 24 Par 8.2.1a

8.2.1 a. The altitude, for application of table 1, is generally determined using the method in Order 8260.44, paragraph 12.3.2 along the flight track distance (see paragraph 8.5.1) However, when that calculation indicates an altitude at or above 10,000 MSL at the IDF, also consider any altitude restrictions and radar assigned altitudes. If aircraft will be limited to below 10,000 MSL at the IDF (and not authorized in excess of 250 KIAS), use the “Below 10,000 MSL” row in the table, even if the calculation indicates an altitude above10,000 MSL. 8.2.1 b. The airspeed, for application of table 1, is generally determined by the standard speed in Order 8260.44, paragraph 11.1 (250 KIAS below 10,000 and 310 KIAS above 10,000). Exceptions: if a speed in excess of 250 KIAS will be published/coded for the procedure or if a speed in excess of 250 KIAS is otherwise authorized to be used below 10,000 MSL, for example by high performance aircraft, use the row for “Above 250 KIAS. 8.2.1 c.

Both the altitude and airspeed requirements must be met in order to use the smaller radius values in the top row of table 1. 8.2.1 d. The level of RNAV criteria for use in table 1 is the level used for design of the RNAV route outbound from the IDF. To use level 1 criteria, the procedure must be limited to the RNAV “Type” and/or RNP level indicated in Order 8260.46 and the IDF must be within 30 NM of the departure airport. 8.2.1 e. For intercept angles smaller than 45o and/or airspeed less than 250 KIAS, a reduction to the PNA arc radius values in table 1 may be requested. Reduced PNA arc radius values require approval from Flight Standards Service. 8.2.2 PNA Obstacle Evaluation Area. In addition to the area identified for pilot navigation (paragraph 8.2.1), also evaluate a PNA buffer area (paragraph 8.2.3) and an IDF turn expansion area (paragraph 8.2.4) for required obstacle clearance (see figure 15). Evaluate from the PNA boundary through the OEA to the latest reception of the IDF.

Par 8.2.2 Page 25

Figure 15. PNA Obstacle Evaluation Area

INITIAL DEPARTURE

INITIAL DEPARTURE

FIX (IDF)

Where = Design Intercept Angle (Maximum of 45°) PNAr = Pilot Navigation Area (PNA) Radius θ

See paragraph 8.2.4 for IDF turn area to be evaluated for PNA OCA

Latest Reception

of Fix

FIX DISPLACEMENT

AREA

See Paragraph 8.2.4

for IDF turn area

See paragraph 8.2.3

FIX DISPLACEMENT

for buffer area

See paragraph 8.2.3

for buffer area

See paragraph

8.2.1 for PNA

RNAV OUTBOUND COURSE

FDT θ

θ

PNAr

PNAr

PNA

PNA

4 NM

4 NM

4 NM

MAXIMUM INTERCEPT ANGLE

MAXIMUM

INTERCEPT

ANGLE

4 NM

8.2.3 PNA Buffer Area.

An obstacle buffer surrounds the PNA on the RNAV route side of the PNA and

MAXIMUM INTERCEPT ANGLE

extends to the latest reception of the IDF (see figure 16). The buffer is normally 4 NM. However, when the radar system used to vector aircraft to the PNA uses a 5 NM buffer, as indicated in Order 8260.19, use 5 NM for this buffer also.

Page 26 Par 8.2.3

Figure 16. PNA Buffer Area

INITIAL DEPARTURE

INITIAL DEPARTURE

FIX (IDF)

Where

= Design Intercept Angle (Maximum of 45°) PNAr = Pilot Navigation Area (PNA) Radius 4 NM is the normal buffer. The buffer increases to 5 NM when required by paragraph 8.2.3.

θ

See Paragraph 8.2.4 for turn area to be evaluated

for PNA OCA

Latest Reception

FIX (IDF)

of Fix

FIX DISPLACEMENT

AREA

See Paragraph 8.2.4 for turn area to be evaluated

for PNA OCA

NOTE: The area after

the IDF FDT is not evaluated for PNA OCA

RNAV

OUTBOUND COURSE

FDT θ

θ

PNAr

PNAr

PNA

PNA

4 NM

4 NM

4 NM

MAXIMUM INTERCEPT ANGLE

MAXIMUM

INTERCEPT

ANGLE

4 NM

8.2.4 IDF Turn Area.

MAXIMUM INTERCEPT ANGLE

The IDF turn area is a maneuvering area required to transition from the PNA to the RNAV route and requires expansion of the PNA and RNAV route areas, as shown in figures 17 and 18. The turn area construction is based on aircraft using a distance of turn anticipation (DTA) as they “fly-by” the IDF. Connect to the RNAV route area as follows: 8.2.4 a. Construct areas for the PNA (paragraph 8.2.1), PNA buffer (paragraph 8.2.3), and for the RNAV route (paragraphs 9.1 and 9.2). 8.2.4 b. Connect a DTA expansion line equal to 1/2 of the maximum IDF intercept angle, to each point of tangency (points E and J in figures 17 and 18) at the PNA buffer boundary. Extend this line to intersect both the primary and secondary boundary of the RNAV route (to points B and A and to points M and N in figures 17 and 18).

Par 8.2.4b Page 27

Figure 17. Connecting PNA to RNAV Route,

±45° Intercept Angle

IF

C

B

A

L

K

H

Q

R M

N

G

O

P

J

I

E

D

(TANGENT POINT)

(TANGENT POINT)

(TANGENT POINT)

1/2 INTERCEPT ANGLE

1/2 INTERCEPT ANGLE

LATEST ATRK FDT

+45°

-45°

THIS EXAMPLE

THIS EXAMPLE

22.5°

22.5°

F

8.2.4 c. Construct a line perpendicular to the RNAV course at the latest IDF fix displacement tolerance (FDT) measured along the flight track (ATRK). Extend the line to intersect the DTA expansion line or the RNAV route secondary boundary, whichever occurs last (to points C and L in figures 17 and 18). 8.2.4 d. The PNA obstacle evaluation area is enclosed by points C-E, PNA buffer arc to F, F-G, PNA arc to H, H-I, PNA buffer arc to J, J-L, and L-C in figure 17. Evaluate the area enclosed by points C-D-K-L-C as both a part of the PNA OEA and a part of the OEA of the first segment of the RNAV route. Evaluate this area as all primary area. 8.2.4 e. Extend the route secondary boundary as necessary to intersect the DTA expansion line, even if the intersect point occurs PRIOR to the latest along-track FDT. An example is point M in figure 18.

THIS EXAMPLE

8.2.4 e. (1) A 30-degree intercept is shown in figure 18 as an example of when it is required to extend the route secondary boundary to the DTA expansion line.

Page 28 Par 8.2.4e(1)

Figure 18. Connecting PNA to RNAV Route, Example Using +45°/-30° Intercept Angle Construction

IDF

THIS EXAMPLE

RNAV ROUTE

RNAV ROUTE

C

B

A

M

DTA EXPANSION LINE

L L’

N

R

Q H

J

I

G

P

O

K

F

D

(TANGENT POINT)

E (TANGENT POINT)

1/2 INTERCEPT ANGLE

EXTEND SECONDARY BOUNDARY TO INTERSECT DTA EXPANSION LINE AT POINT M

DTA EXPANSION LINE

BEGIN SECONDARY AREA

AT LINE A-B

BEGIN SECONDARY AREA

AT LINE M-N

LATEST ATRK FDT

LATEST ATRK FDT

+45°

-30° THIS EXAMPLE

15°

22.5°

8.2.4 e. (2) The PNA obstacle evaluation area is enclosed by points C-E, PNA buffer arc to F, F-G, PNA arc to H, H-I, PNA buffer arc to J, J-M, M-L, L-C in figure 18. Evaluate the area enclosed by points C-D-K-M-L-L’-C as both a part of the PNA OEA and a part of the OEA of the first segment of the RNAV route. Evaluate this area as all primary area except for the segment M-L-L’-M which may be considered as secondary area. 8.2.4 f. If the point of tangency (point E or point J) is on or inside the RNAV route SECONDARY boundary line (extended), connect the DTA expansion line to the earliest ATRK FDT line of the IDF (connecting point J to R or point E to O).

-30° THIS EXAMPLE

NOTE: This paragraph only needs to be considered for small intercept angles. For example, when points R and O are 6 NM from the RNAV route and the PNA radius is 7 NM, this paragraph only applies at an intercept angle of 16.6 degrees or smaller. 8.2.4 g. If the point of tangency (point E or point J) is on or inside the RNAV route PRIMARY boundary line (extended), connect the DTA expansion line to the earliest ATRK FDT line of the IDF (connecting point J to Q or point E to P).

NOTE: This paragraph only needs to be considered for a zero degree intercept angle (where intercepts are planned for only one side of the RNAV course, as shown in the lower portion of figure 14).

Par 8.3 Page 29

8.3 OBSTACLE CLEARANCE. Evaluate the PNA OEA with an inclined OIS/OCS and a level OCS. Use the inclined OIS/OCS until reaching the level OCS. Use the level OCS from the PNA boundary, or maximum intercept line, until abeam the latest reception point of the Initial Departure Fix (line C-L in figures 17 and 18). 8.3.1 PNA Inclined Obstacle Evaluation Surfaces.

The PNA inclined OIS rises at a 40:1 slope (see figures 19 and 20). Use a higher OCS, and associated CG, if there are penetrations of the 40:1 OIS. The starting height of the OIS at the PNA boundary equals the height of the RVA OIS/OCS. If a minimum crossing altitude (MCA) at the PNA boundary is requested, see paragraph 8.4.2. Terminate the inclined OIS/OCS if it reaches the level OCS associated with the PNA altitude.

Figure 19. PNA OIS/OCS Continuing from RVA OIS/OCS

The RVA inclined OCS, when it is lower than the

level OCS, continues

into the PNA

Terminate the

Inclined OCS if it reaches the PNA level OCS

Boundary

RVA PNA

RVA PNA

Level

OCS

Level OCS

MVA / MIA

Departure Runway(s)

Radar Vector Area (RVA)

Minimum CG

PNA Inclined OCS Inclined OCS

Pilot Navigation

Area (PNA)

ROC ROC

Page 30 Par 8.3.1

Figure 20. PNA OCS Starting at Height of RVA Level OCS

RVA climb gradient

The RVA level OCS, when it is lower than the

ROC ROC

inclined OCS, is the beginning height for

the PNA OCS

Departure Runway(s)

Radar Vector Area (RVA)

Pilot Navigation

Area (PNA)

Inclined OCS

ROC

MVA / MIA ROC

Level OCS

Boundary

RVA PNA

MVA / MIA

Altitude

8.3.2 PNA Level Obstacle Clearance Surface.

Use the ROC indicated in Order 8260.19, chapter 3, section 7.

MVA / MIA

NOTES: 1. This is the same ROC and same rounding method used for radar sectors. 2. Also see accuracy requirements in Order 8260.19, chapter 2, section 11. 8.3.3 Mitigating Obstacle Penetrations.

The preferred method of obstacle mitigation is to use a less onerous route. The next choice is a climb gradient, using paragraph 8.6. Also see Order 8260.3, Volume 4, and Order 8260.46. 8.4 PNA ALTITUDE. The PNA minimum altitude (PNAma) is the altitude aircraft must reach to safely proceed through the PNA to the IDF. Provide this altitude to Air Traffic as indicated in Order 8260.46. 8.4.1 PNA Minimum Altitude. Determine the PNAma as the higher of the following: 8.4.1 a. RNAV Minimum Reception Altitude. See paragraph 6.3. 8.4.1 b. Altitude Based on Obstacle Clearance.

Par 8.4.1b Page 31

Evaluate the OEA from the PNA boundary to the latest reception of the IDF (see paragraph 8.3). 8.4.1 c. Altitude Based on Airspace Analysis of the PNA OEA. Evaluate the PNA OEA using Order 8260.19, paragraph 504, and Order 7400.2, Procedures for Handling Airspace Matters, Part 4. Apply a terminal rather than an en route airspace buffer when evaluating the PNA.

8.4.1 d. Altitude Based on Other Operational Factors. Operational necessity may require an altitude increase. Examples include Air Traffic Control (ATC) requests, minimum crossing altitude (MCA), radar and communications coverage, noise abatement, national security, or environmental. 8.4.1 e. Altitude Based on Flight Inspection. If the flight inspection indicates a higher altitude is required, use that altitude. An example would be to recommend an increase based on precipitous terrain. 8.4.2 PNA Boundary Minimum Crossing Altitude.

The recommended design is for aircraft to cross the PNA boundary at or above the PNA minimum altitude, as calculated in paragraph 8.4.1. If a PNA boundary minimum crossing altitude is established, it must be at or above the RNAV MRA. Raise the starting height of the PNA inclined OCS, described in paragraph 8.3.1, to a height that equals the PNA boundary minimum crossing altitude minus the ROC indicated in Order 8260.19, chapter 3, section 7. An MCA must provide the ROC; that is, no penetrations of the PNA inclined OCS are allowed. 8.5 MINIMUM DISTANCE/MAXIMUM CG FROM DER TO THE PNA BOUNDARY. The minimum distance from the DER to the PNA boundary must be sufficient to allow aircraft to reach the PNA minimum altitude. When a PNA altitude is determined or modified, verify the distance/gradient to the PNA boundary. 8.5.1 CG Calculation. Calculate this ATC CG along the shortest flight distance allowed by the radar vectoring procedures, as follows: CG = (PNAma – DERe) / FTD. Where CG = ATC Climb Gradient from takeoff to the PNAma PNAma = Pilot navigation area minimum altitude (paragraph 8.4.1) DERe = Departure end of runway elevation FTD = Minimum flight track distance from takeoff to the PNA 8.5.1 a. If using the straight-line distance from DER to PNA, as an approximation of the FTD in the CG formula above, indicates an acceptable gradient, there is no requirement to estimate the flight track distance.

Page 32 Par 8.5.1b

8.5.1 b. If the estimated flight track distance is required and if ATC provides an estimate of the shortest flight track distance, use that estimated distance as the FTD for this CG calculation. 8.5.1 c. If estimated distance or vectoring procedure information is not provided, use a flight track distance defined by an initial climb to 400 ft (or higher minimum turn altitude if one is specified) then along the shortest allowable headings/routes to proceed toward the initial departure fix. 8.5.2 CG Calculation. Submit the CG from this calculation to be published if it is greater than the applicable obstacle CG/standard CG. 8.5.2 a. This CG is an ATC climb gradient, rather than an obstacle CG, if required under this paragraph. 8.5.2 b. The “climb-to” altitude is the PNA minimum altitude, if a CG is required. 8.5.3 The flight track distance to the PNA must not require a climb gradient in excess of 500 ft per NM, unless approval is obtained from Flight Standards. Before submitting a request for a climb gradient of more than 500 ft per NM to reach an RNAV MRA, also consider modifying vectoring procedures or changing the location of the PNA, or requiring IRU or GPS (if that would lower the CG). 8.6 CLIMB GRADIENT.

Apply the standard climb gradient of 200 ft per NM from TERPS Volume 4 unless a higher gradient is required. 8.6.1 CG from DER to PNA Boundary. See paragraph 8.5. 8.6.2 CG from PNA Boundary to the IDF. 8.6.2 a. When an altitude restriction is required at the IDF, such as an MCA or an operational/ATC restriction, determine the climb gradient from the PNA boundary to the IDF as follows:

CG = (IDFxa – PNAma) / PNAr Where CG = Climb gradient required from the PNA boundary to the IDF IDFxa = Initial departure fix minimum crossing altitude/restriction PNAma = Pilot navigation area minimum altitude PNAr = Pilot navigation area radius (estimated distance through the PNA)

NOTES: 1. This is a variation of the CG formula in Order 8260.3, Volume 4, para- graph 1.4.

Par 8.6.2a Page 33

2. This formula applies when the Initial Departure Fix minimum crossing altitude is required for either obstacle clearance reasons or other reasons, such as ATC. Submit the CG, for publication, as an obstacle CG if the crossing altitude is an MCA required for obstacle clearance; otherwise, submit it as an ATC CG. 3. If a minimum crossing altitude at the PNA boundary was established, use that crossing altitude instead of the PNAma in the formula. 4. An example calculation is an initial departure fix minimum crossing altitude of 4,000 ft MSL, a pilot navigation area minimum altitude of 1,900 ft MSL, and a pilot navigation area radius of 7 NM gives a CG of 300 ft per NM. 5. An example of submitting a climb gradient is as follows: With no obstacle CG required in the RVA or the RNAV route and the CG calculated above, the values to submit would be a CG of 300 ft per NM (from takeoff) to 4,000 MSL. An alternative for the CG termination is until crossing [waypoint name of the IDF]. 8.6.2 b. If the climb gradient from the PNA altitude to the IDF minimum crossing altitude requires higher than the standard climb gradient, take one of the following actions: 8.6.2 b. (1) Raise the pilot navigation area minimum altitude. 8.6.2 b. (2) Re-orient the RNAV route. 8.6.2 b. (3) Relocate the IDF. 8.6.2 b. (4) Publish a climb gradient. Use the climb gradient calculations from paragraph 8.6.2a. 8.6.2 b. (5) A combination of the actions listed above.

NOTE: If changes are made to distances, routes or altitudes, you must evaluate again any related gradients, distances, or altitudes that are adversely affected by the change. 8.6.3 CG to Mitigate a Penetration of the PNA Inclined OIS.

The obstacle climb gradient calculation, for the inclined OIS/OCS, depends on

the location of the obstacle and the origin of the inclined OIS. Use the applicable paragraph as indicated in table 2.

Page 34 Par 8.6.3

Table 2. Climb Gradient Calculation –

Determining Paragraph to Use

Location of Obstacle

Origin of PNA Inclined OIS

Within Extended ICA Splay

Outside Extended ICA Splay

PNA OIS Continues from the RVA Inclined OCS

Paragraph

8.6.4 Paragraph

8.6.4 Paragraph

8.6.5

PNA OIS Starts at the RVA Level OCS Paragraph 8.6.6

8.6.4 CG to Mitigate a Penetration of the PNA OIS for Obstacles Within the Extended ICA Splay When the PNA OIS Continues from the RVA OIS/OCS. 8.6.4 a. An obstacle(s) must be within the extended splay lines of the ICA to use this paragraph. Figure 21 shows example obstacle measurements from the DER/ICAB to obstacles C, D, E, F, and G. 8.6.4 b. The PNA inclined OIS/OCS must originate at the same height as the RVA inclined OIS/OCS, as shown in figure 19, to use this paragraph. See para- graph 7.6.2a for the termination altitude and distance of the RVA inclined OCS. 8.6.4 c. The climb gradient calculation is done as indicated in paragraph 7.6.2b.

8.6.4 d. For the “climb to” altitude, use the PNA minimum altitude, from para- graph 8.4, unless a lower altitude is needed. For an obstacle within the extended splay lines of the ICA (see figure 21), the CTA may be established as low as the value calculated in paragraph 7.6.2c.

Par 8.6.4d Page 35

Figure 21. Measurements to Obstacles Within the ICA Splay - When PNA OIS/OCS Continues from RVA

INITIAL DEPARTURE

FIX (IDF)

Latest Reception

of Fix

Extension of ICA Splay Line

Extension of ICA Splay Line

RNAV

COURSE PNA

A

B C D

E

F G

H

I J

K

L

MAXIMUM INTERCEPT ANGLE

MAXIMUM

INTERCEPT

MAXIMUM INTERCEPT ANGLE

ANGLE

Primary Area Obstacle Clearance Surface 40:1

DER

Departure

Runway

8.6.5 CG to Mitigate a Penetration of the PNA OIS for Obstacles Outside the Extended ICA Splay When the PNA OIS Continues from the RVA OCS. 8.6.5 a. An obstacle(s) must be outside the extended splay lines of the ICA to use this paragraph to determine the obstacle clearance climb gradient. Figure 22 shows example obstacle measurements from the ICA to obstacles A, B, H, I, J, K, and L for the example runway 07. Measurements are the shortest distance to the obstacle from the DRP, runway, or ICA as shown for the example runway 16. 8.6.5 b. The PNA inclined OIS/OCS must originate at the same height as the RVA inclined OIS/OCS, to use this paragraph. See paragraph 7.6.3a for the termination altitude and distance of the RVA inclined OIS. 8.6.5 c. The climb gradient calculation is done as indicated in paragraph 7.6.3b.

8.6.5 d. For the “climb to” altitude, use the PNA minimum altitude, from para- graph 8.4, unless a lower altitude is needed. For an obstacle outside the extended splay lines of the ICA (figure 22), the CTA may be established as low as the value calculated in paragraph 7.6.3c.

Page 36 Par 8.6.5d

Figure 22. Measurements to Obstacles Outside ICA Splay - When PNA OIS/OCS Continues from RVA

INITIAL DEPARTURE

INITIAL DEPARTURE

FIX (IDF)

Latest Reception

of Fix

Extension of ICA Splay Line

Extension of ICA Splay Line

RNAV

COURSE PNA

A

B C D

E

F G

H

I J

K

L

Maximum Intercept Angle

Maximum

Intercept

Angle

Measurements for departure from runway 16 to obstacles A,B,C,D and E are from the runway 16 DRP

COURSE PNA

Measurement for departure from runway 16 to obstacle F uses the shortest distance (perpendicular) from runway 16

Measurements for departure from runway 16 to obstacles G,H,I,J,K and L are from the runway 16 ICA

Primary Area Obstacle Clearance Surface 40:1

DER

End of ICA

DER

DRP

ICA

ICA

Departure

Runway 17

Departure Runway 16

8.6.6 CG to Mitigate a Penetration of the PNA OIS When the OIS Originates at the Height of the RVA Level OCS. 8.6.6 a. An obstacle(s) may be either inside or outside the extended splay lines of the ICA to use this paragraph. Figure 23 shows example obstacle measurements using the shortest distance from the PNA boundary, or the maximum intercept lines, to all obstacles. 8.6.6 b. The RVA inclined OIS/OCS must have reached the RVA level OCS as shown in figure 20. The PNA inclined OIS starts at the height of the RVA level OCS.

Par 8.6.6c Page 37

8.6.6 c. Calculate the obstacle clearance climb gradient, when the PNA inclined OIS starts at the height of the RVA level OCS, as follows:

CG = O - E .76 D

Where

CG = Climb gradient in ft per NM O = Obstacle (MSL) elevation E = CG origin starting (MSL) elevation. For origin elevation, use the elevation of the RVA OCS at the PNA boundary. D = Distance (NM) from the PNA boundary, or intercept lines, to the obstacle.

NOTES: 1. This CG is a variation of Order 8260.3, Volume 4, chapter 1, para- graph 1.4.1. DOD procedures may use the DOD option in paragraph 1.4.1. 2. Measurements for obstacle distance (D) for CG calculations are made from the same origin as the measurements for the OIS/OCS calculations. 8.6.6 d. The “climb to” altitude is the PNA minimum altitude, from paragraph 8.4.

Page 38 Par 8.6.6d

Figure 23. Measurements to Obstacles - When PNA OIS/OCS Starts at the Height of the RVA Level OCS

INITIAL DEPARTURE

INITIAL DEPARTURE

FIX (IDF)

Latest Reception

of Fix

RNAV

COURSE PNA

A

B

C D

E

F G

H

I J

K

L

Maximum Intercept Angle

Maximum

Intercept

Angle

Primary Area Obstacle Clearance Surface 40:1

DER

DER

DRP

ICA

ICA

Departure

Runway 07

Departure Runway 16

Measurements for all runways are from the closest point on the PNA Boundary or, for obstacles A, B, and L, from the maximum intercept angle line. The origin height is the RVA level OCS elevation.

COURSE PNA

8.6.7 End of PNA Inclined Obstacle Surface and CG Evaluation.

Obstacle measurements and climb gradient calculations under paragraphs 8.6.4,

8.6.5, and 8.6.6 are only required until the inclined OIS/OCS reaches the height of the PNA level surface OCS. Then, the inclined OIS/OCS is terminated and PNA obstacle mitigation is through the level OCS and establishing the PNA altitude. 9.0 RNAV ROUTE.

The RNAV route begins at the IDF and includes all subsequent segments including transitions. 9.1 ALIGNMENT. The RNAV route obstacle clearance area for the first RNAV segment is aligned on the outbound course from the IDF.

Par 9.2 Page 39

9.2 AREA.

Apply level 2 (RNP 2.0) route width, as described in Order 8260.44, to the RNAV route segment of the SID. Exception: You may use level 1 (RNP 1.0) criteria, within 30 NM of the departure airport, if the conditions and limitations stated in Orders 8260.44 and 8260.46 are met. If level 1 criteria are used, the area width beyond 30 NM is the same as level 2 primary and secondary area widths. Additional area for the IDF turn area must be considered in the obstacle evaluation of the RNAV route as indicated in paragraph 8.2.4 (see figure 24).

Figure 24. Area for First Segment of RNAV Route

INITIAL DEPARTURE

INITIAL DEPARTURE

FIX

RNAV OUTBOUND COURSE

RNAV ROUTE OCA IS FROM ORDER 8260.44

SEE PARAGRAPH 8.2.4 FOR THE IDF TURN AREA

SECONDARY AREA

SECONDARY AREA

EARLIEST ALONG TRACK FDT

1 NM (LEVEL 1) OR 2 NM (LEVEL2)

1 NM (LEVEL 1) OR 2 NM (LEVEL2)

2 NM (LEVEL 1) OR 4 NM (LEVEL2)

2 NM (LEVEL 1) OR 4 NM (LEVEL2)

PRIMARY AREA

PRIMARY AREA

PRIMARY AREA

SEE PARAGRAPH 8.2.4 FOR THE IDF TURN AREA

9.3 OBSTACLE CLEARANCE. Evaluate the RNAV route area, including the IDF turn expansion area, each subsequent segment, and each transition using Orders 8260.3, 8260.44, and 8260.46. The Obstacle evaluation area starts abeam the earliest reception point (the earliest along-track fix displacement tolerance) of the IDF and continues until abeam the latest reception point (the latest along-track fix displacement tolerance) of the next fix or waypoint (see figure 25).

SEE PARAGRAPH 8.2.4 FOR THE IDF TURN AREA

Page 40 Par 9.3

Figure 25. RNAV Route Obstacle Evaluation Area

IDF RNAV ROUTE

C

B

A

M

L L’

N

R

Q H

J

I

G

P

O

K

F

D

E

1/2 INTERCEPT ANGLE

1/2 INTCP ANGLE

BEGIN SECONDARY AREA

AT LINE A-B

LATEST RECEPTION OF NEXT WAYPOINT - END OF OEA FOR RNAV ROUTE FIRST SEGMENT MINIMUM ALTITUDE AND BEGIN

OEA FOR NEXT SEGMENT MCA

OEA FOR NEXT SEGMENT MCA

USING INCLINED OCS.

LATEST RECEPTION OF IDF - BEGIN OEA FOR RNAV ROUTE MCA

USING INCLINED OCS

EARLIEST RECEPTION

OF IDF - BEGIN OEA FOR RNAV ROUTE MINIMUM ALTITUDE USING LEVEL OCS

NEXT WAYPOINT NEXT SEGMENT

OF RNAV

ROUTE

BEGIN SECONDARY AREA

AT LINE M-N

LATEST ATRK FDT

LATEST ATRK FDT

PNA

PNA

9.3.1 MCA Inclined Obstacle Clearance Surface.

The MCA OCS starts at the latest reception (latest ATRK FDT) of the previous segment, as shown by line C-L in figure 25 and rises as described in Order 8260.3, Volume 1 or Volume 4, as applicable. The starting height begins at the lower of the inclined or level surface height from the previous segment, as shown in figures 26 and 27. Terminate the inclined OCS upon reaching the level OCS associated with the RNAV route segment MEA or minimum altitude. 9.3.2 RNAV Route Level Obstacle Clearance Surface.

Use the surfaces and ROC as described in Order 8260.3, Volume 1 or Volume 4, as applicable.

Par 9.3.2 Page 41

Figure 26. MCA OCS Continuing from Previous OCS

The PNA inclined OCS, when it is lower than the PNA level OCS, is the origin

of the MCA inclined OCS

If obstacles are below both surfaces, no mitigation is required

Terminate the

Inclined OCS when it reaches

the level OCS

Latest Reception

of IDF

IDF

Earliest Reception

of IDF

RNAV Route

Level OCS

PNA Level OCS

MCA Inclined OCS PNA Inclined OCS

FDT FDT

FDT FDT

Pilot Navigation

Area (PNA)

RNAV Route

Figure 27. MCA OCS Starting from Level OCS

The PNA level OCS when it is lower than the

PNA inclined OCS,

is the origin of the MCA inclined OCS

If obstacles are below both surfaces, no mitigation is required

Terminate the

Inclined OCS when it reaches

the level OCS

Latest Reception

of IDF

IDF

Earliest Reception

of IDF

RNAV Route

Level OCS

PNA Level OCS

PNA Inclined OCS MCA Inclined OCS

FDT FDT

Pilot Navigation

Area (PNA)

RNAV Route

9.3.3 Obstacle Measurements.

Obstacle measurements are the shortest distance from the start of the inclined OCS to the obstacle within the primary area and perpendicular to the course within the secondary area, as shown in figure 28.

Page 42 Par 9.3.3

Figure 28. Obstacle Areas and Measurements

PREVIOUS

FIX

NEXT

FIX

AREA IS FROM ORDER 8260.44

AREA IS FROM ORDER 8260.44

AND TERPS

ABEAM PLOTTED FIX

START OF MCA

INCLINED OCS ABEAM PLOTTED FIX

LATEST

ALONG TRACK FDT

EARLIEST

ALONG TRACK FDT

LEVEL OBSTACLE CLEARANCE SURFACE

FOR DEPARTURE SEGMENT

LATEST

ALONG TRACK FDT

Secondary Area Obstacle Clearance Surface 12:1

Use En Route Criteria For Secondary Areas

ALONG TRACK FDT

Instead of 12:1 OCS When Required By TERPS Volume 1, Chapter 17

Primary Area Obstacle Clearance Surface 40:1

Use En Route Criteria For Primary Areas

Instead of 40:1 OCS When Required By TERPS Volume 1, Chapter 17 9.4 RNAV ROUTE ALTITUDE. Publish a minimum altitude/minimum en route altitude (MEA) for all segments following the IDF. Publish a minimum crossing altitude when required. 9.4.1 RNAV Route Minimum Altitude. The MINIMUM altitude for each segment of the RNAV Route is the higher of: 9.4.1 a. Previous Segment Altitude. Use at least the PNA minimum altitude (paragraph 8) in determining the altitude for the first segment after the IDF. Then, use at least the previous segment altitude for each following segment. 9.4.1 b. Altitude Based on Obstacle Clearance. Use paragraph 9.3, and Order 8260.3, Volume 4 or, when applicable, Volume 1, chapter 17. 9.4.1 c. Altitude Based on Airspace Analysis. Use Orders 8260.19 and 7400.2.

Par 9.4.1d Page 43 (and 44)

9.4.1 d. Altitude Based on Other Operational Factors/Operational Necessity. Examples include noise abatement, environmental, ATC operational requirements/restrictions, radar and communications coverage, or national security. 9.4.1. e. Altitude Based on Flight Inspection. A minimum altitude resultant from flight inspection. 9.4.2 Minimum Crossing Altitude. Evaluate each segment for MCA using Order 8260.3, Volume 4 or Volume 1, chapter 17, as applicable. You may raise a previous segment minimum altitude to meet the subsequent segment MCA calculated altitude (and remove the need for publishing the MCA) when there is no adverse effect on the previous segment gradient. 10.0 COORDINATION, DOCUMENTATION, AND PROCESSING. Refer to Order 8260.46. 11.0 INFORMATION UPDATE. For your convenience, FAA Form 1320-19, Directive Feedback Information, is included at the end of this order to note any deficiencies found, clarifications needed, or suggested improvements regarding the contents of this order. When forwarding your comments to the originating office for consideration, please use the “Other Comments” block to provide a complete explanation of why the suggested change is necessary.

FAA Form 1320-19 (8-89)

Directive Feedback Information Please submit any written comments or recommendations for improving this directive, or suggest new items or subjects to be added to it. Also, if you find an error, please tell us about it. Subject: Order 8260.53, Standard Instrument Departures that Use Radar Vectors to Join RNAV Routes To: DOT/FAA Flight Procedure Standards Branch, AFS-420 P.O. Box 25082 Oklahoma City, OK 73125 (Please check all appropriate line items) … An error (procedural or typographical) has been noted in paragraph … on page … … Recommend paragraph … on page … be changed as follows: (attach separate sheet if necessary) … In a future change to this directive, please include coverage on the following subject: (briefly describe what you want added): … Other comments: … I would like to discuss the above. Please contact me. Submitted by: … Date: … FTS Telephone Number: Routing Symbol: …