Order 8110.100B Special Airworthiness Information Bulletin
U.S. DEPARTMENT OF TRANSPORTATION ORDER FEDERAL AVIATION ADMINISTRATION
U.S. DEPARTMENT OF TRANSPORTATION ORDER FEDERAL AVIATION ADMINISTRATION
National Policy 8110.100B
07/24/2013
SUBJ: Special Airworthiness Information Bulletin
1. Purpose of This Order. This order shows you how to develop and issue a special airworthiness information bulletin (SAIB).
2. Audience. All Federal Aviation Administration (FAA) employees and managers who write or approve SAIBs.
3. Where to Find this Order? You can find this order on the Directives Management System (DMS) Web site at https://employees.faa.gov/tools resources/orders notices/ or http://www.faa.gov/regulations policies/orders notices/ and the FAA's Regulatory and Guidance Library (RGL) Web site at http://rgl.faa.gov.
4. What This Order Cancels. This order cancels FAA Order 8110.1 00A, Special Airworthiness Information Bulletin, dated 09/18/l 0.
5. Explanation of Changes. We revised this order to:
a. Add guidance regarding when not to use an SAIB. See paragraph 9d.
b. Highlight the need to coordinate with the certifying civil aviation authority (CAA) for imported products. See paragraph 1 la(3).
c. Clarify what information should be included when drafting an SAIB. See paragraphs 11 b(2), 11 b( 4), and appendix A.
6. Effective Date. This order is effective on 08/21/13.
7. Purpose of an SAIB. We developed the SAIB as an information tool to alert, educate, and make recommendations to the aviation community about ways to improve the safety of a product. The target audience may be narrow or broad, from parachute riggers to type clubs. An SAIB contains non-regulatory, non-mandatory information and guidance for safety issues that do not meet the criteria for airworthiness directive (AD) action under Title 14 of the Code of Federal Regulations (14 CFR) part 39.
8. When to Use an SAIB.
a. The decision when to use an SAIB is determined by each product directorate's decision-making process for continued operational safety, which will, in most cases, be the result of going through the process outlined in FAA Order 8110.107, Monitor Safety/Analyze Data. Any criteria or guidance developed to clarify when to use an SAIB must include, as a minimum, the guidance provided in this order.
b. An SAIB should only be used to offer information about ways to improve a product's
Distribution: Electronic Distribution Initiated By: AIR-110
safety. It is advisory in nature, and not mandated by regulatory action. In particular, an SAIB may be used to notify the aviation community of the following:
(1) An airworthiness concern that has not yet been determined to be an unsafe condition. The SAIB must clearly state that, at the time the SAIB is issued, the airworthiness concern is not an unsafe condition that would warrant AD action under
14 CFR part 39. The SAIB may reference recommended actions from service information.
(2) An unsafe condition on aircraft with a special airworthiness certificate, such as for the purpose of amateur-built, which do not have a type certificate. Without a type certificate, these aircraft have no approved type design; therefore, we will not issue an AD for them. The SAIBs for these aircraft are still recommended actions and not mandatory.
(3) Information on an approved alternative method of compliance (AMOC) to an AD. Only the identity ofpersons or organizations that have received an AMOC approval should be specified in the SAIB. Other information regarding the content or substance of an AMOC must be handled under the Freedom of Information Act.
c. An SAIB may also be used to request voluntary reporting of information on the safety of a product (e.g., inspection results). Under the provisions ofthe Paperwork Reduction Act of 1995 (44 U.S.C. 3501 et seq.), the Office of Management and Budget (0MB) has approved the collection of information. The 0MB control number is 2120-0731.
9. When Not to Use an SAIB. As previously stated, an SAIB is a non-mandatory document that is advisory in nature. It only makes recommendations and, therefore, must not be used to:
a. Correct an unsafe condition on type certificated products. When determining that an airworthiness concern is an unsafe condition, including one identified by issuance of mandatory continuing airworthiness information (MCAI), do not use an SAIB to convey the required corrective actions. Additionally, an SAIB cannot be used to:
(1) Identify an interim corrective action while an AD is being developed.
(2) Clarify any requirements specified in an AD. If clarification is needed, revise or supersede the AD.
(3) Grant special exemptions or an AMOC to ADs. The AMOC process is the correct process to deviate from an AD.
b. Recommend changes to the limitation section of the airplane/rotorcraft flight manual (AFM/RFM) or the airworthiness limitations section (ALS) in the instructions for continued airworthiness (ICA). Issue an AD to change these mandatory requirements.
c. Change approved maintenance actions. Refer any recommended changes to an operator's maintenance program to the appropriate flight standards district office (FSDO) for review and approval.
d. Provide guidance, instructions, or training to FAA aviation safety engineers (ASE) or aviation safety inspectors (ASI) regarding certification or field approval activities. Use
directives, policy memos, or other methods (e.g., issue papers) to convey the necessary information.
10. Responsibilities.
a. AIR Headquarters Offices are responsible for drafting and approving SAIBs for programs or processes of assigned responsibility ( e.g., technical standard orders (TSO)).
b. Directorates and Aircraft Certification Offices (ACO).
(1) Directorates, and the AC Os they oversee, are responsible for developing SAIBs for their products of assigned responsibility. (See FAA Order 8100.5, Aircraft Certification Service, Mission, Responsibilities, Relationships, and Programs, for specific product responsibility.) For SAIBs dealing with an appliance or article having a TSO authorization (TSOA) or a TSO Letter of Design Approval (LODA), the ACO overseeing that approval holder is responsible for drafting the SAIB.
(2) Directorates are responsible for reviewing and approving SAIBs for content and document quality. Each directorate must assign a focal point for receiving SAIBs and establish a review process to ensure appropriate content and formatting. Directorate approval and aircraft evaluation group (AEG) acceptance of each SAIB is necessary before publication. In cases of dispute whether an SAIB is necessary, the directorate manager, or his/her designee, will provide the final decision.
c. Engineering Procedures Office (AIR-110). This office:
(1) Assigns SAIB numbers,
(2) Publishes and maintains SAIBs on the RGL Web site (http://rgl.faa.gov), and
(3) Distributes SAIBs electronically.
11. Procedures for Developing and Issuing an SAIB.
a. Development. The ASE or appropriate personnel must first determine if an SAIB is the appropriate action for a specific situation.
(1) For ASEs within an ACO or directorate, use the product directorate's continued operational safety (COS) decision-making process. When an SAIB is appropriate, consult with DAHs, AEG, other CAAs, industry groups, and other sources to ensure the information you will convey is accurate and correct.
(2) For headquarters' ASEs or appropriate personnel, consult with your manager or their designee.
(3) For imported products, consult with the certifying CAA prior to issuing an SAIB that substantially deviates or is additional to guidance issued by the certifying authority.
b. Drafting. Draft the SAIB using the template in appendix A. SAIBs should be uniform in format, style, and quality. Follow the F AA's plain language principles in FAA Order 1000.36, FAA Writing Standards. Attach or insert drawings or figures electronically. When drafting the SAIB, you must:
(1) Include a subject title using Air Transport Association (ATA) or Joint Aircraft System/Component (JASC) subject titles that clearly and concisely reflect the content of the SAIB (for example, Landing Gear). Contact your directorate AD focal point (e.g., AD Coordinator) for a copy ofthe ATA/JASC document. You may add to the ATA/JASC subject title if further clarification is necessary.
(2) Identify all known applicable type certificated makes and models in the Introduction section (highlight them by using bold font). Use the type certificate data sheet to designate the correct DAH, make, and model. Include common names of aircraft only when needed for clarification.
(3) Clearly state, if applicable, that the purpose of the SAIB is to correct an unsafe condition on an aircraft with a special airworthiness certificate in the experimental category that does not have a type certificate.
(4) Clearly state that we have determined that no regulatory action is necessary at this time because the airworthiness concern is not an unsafe condition that would warrant an FAA AD under 14 CFR part 39. It is not required to provide justification as to why the airworthiness concern does not meet the criteria of an AD.
(5) If requesting information, include the following sentence after the request:
"Under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq.), the 0MB has approved the information collection contained in this SAIB, and assigned 0MB Control Number 2120-073 l ."
(6) If revising an SAIB, supplement the original paragraph(s) in the Introduction section with an explanation of why it is being revised. Do not delete the original introduction or background paragraphs.
c. Approval.
(1) For SAIBs initiated by the ACO or directorate, coordinate with the appropriate AEG personnel responsible for the product (except for TSOA or LODA) and send the draft SAIB to the assigned focal point at the directorate responsible for the product, or for TSOA or LODA the directorate that has geographic responsibility for the TSO approval holder. Coordination with the ACO manager is at the discretion of each office. Directorates will review and approve the SAIB to ensure that the SAIB does not state mandatory or regulatory information or directions, and adheres to this order. Directorates are also responsible for reviewing each SAIB for clarity and readability.
(2) For SAIBs initiated by headquarters, obtain approval from your office manager or their designee.
d. Issuance. When the SAIB is approved by the directorate or headquarters office as appropriate, email it to AIR-110 for publication at "9-AMC-AIR140-lnformation [email protected]". Include the SAIB, attachments (if applicable), and an email comment confirming directorate/headquarters approval of the SAIB.
e. Publication.
(1) Before publishing the SAIB, AIR-110 will assign an SAIB number as follows:
(a) [calendar year (CY)-numerical count]. For example, 04-16 is 16th SAIB issued by the FAA in CY 2004.
(b) For revised SAIBs, the originally published SAIB number followed by an "Rl" (or R2, R3, etc., as appropriate), for example CE-04-16Rl. AIR-110 will also change the date of the new SAIB document to reflect the current revision date.
(2) AIR-110 publishes an electronic (pdt) copy of the SAIB to the RGL site. To receive a published copy, directorates, ACOs, AEG personnel, and other interested persons should subscribe to SAIBs for the specific product and model of interest using the instructions on the RGL Web homepage. AIR-110 no longer distributes SAIBs through paper mailings.
(3) AIR-110 will publish an SAIB in RGL within two (2) business days of receiving it. Iffaster handling is required, the directorate/headquarters office must obtain prior approval from the Manager, AIR-110.
f. Revision. Since SAIBs are not mandatory, only revise them for a substantive change (that is, affecting the substance or specific recommendations in the SAIB). The same level of coordination may not be necessary for the revision as for the original issue. At a minimum, the ASE ( or appropriate personnel) should coordinate the revision with either the assigned focal point at the directorate responsible for the product or the headquarters office manager ( or his/her designee, as appropriate. For TSOA or LODA, coordinate the revision with the directorate that has geographic responsibility for the TSO approval holder.
12. Distribution. Distribute this order to the Office of the Chief Counsel (including all counsel in the regional offices); the Flight Standards Service (including regional FSDOs, flight standards field facilities, and AEG); and to the branch levels in the Aircraft Certification Service (directorates, ACOs, and aircraft certification field offices).
13. Suggestions for Improvement. If you find any deficiencies, need clarification, or want to suggest improvements to this directive, send a written or electronic copy of FAA Form 1320-19, Directives Feedback Information, to the Aircraft Certification Service, Administrative Services Branch, AIR-510, Attention: Directives Management Officer or you can provide your feedback by using the automated Directive Feedback System on the Web at http://avsdfs.avs.faa.g0v/default.aspx. If you urgently need an interpretation, contact the Engineering Procedures Office, AIR-110, at ( 405) 954-4103. Always use FAA Form 1320-19 to follow-up each verbal conversation. FAA Form 1320-19 can be found in appendix B and at https://emplo1ees.faa.gav/documentLibrarv/media/form/faa 1320-19.pdf.
14. Records Management. Refer to Orders 0000.1, FAA Standard Subject Classification System; 1350.14, Records Management; and 1350.15, Records, Organization, Transfer and Destruction Standards; or your Records Management Officer or Directives Management Officer for guidance regarding retention or disposition of records.
~G,.1.4_
s:,o,._ David W. Hempe
Manager, Aircraft Engineering Division Aircraft Certification Service
07/24/2013 8110.100B Appendix A Appendix A. Template
FAA SPECIAL AIRWORTHINESS Aviation Safety INFORMATION BULLETIN
SAIB: SUBJ: [Insert subject title] Date: This is information only. Recommendations aren't mandatory.
Introduction
This Special Airworthiness Information Bulletin ... [refer to paragraph 11b ofthis order for required information].
At this time, the airworthiness concern is not an unsafe condition that would warrant airworthiness directive (AD) action under Title 14 ofthe Code of Federal Regulations (14 CFR) part 39.
Background
[Insert briefexplanation for SAIB]
Recommendations
[Insert recommended actions]
For Further Information Contact
[Insert name], Aerospace Engineer, [Insert office address]; phone: (xxx) xxx-xxxx; fax: (xxx) xxx-xxxx; email: XXXX.
(Optional) For Related Service Information Contact
[Insert company name], [Insert company address]; phone: (xxx) xxx-xxxx; fax: (xxx) xxx-xxxx.
0
07/24/2013 8110.100B Appendix B
Appendix B. FAA Form 1320-19, Directive Feedback Form
Appendix B. FAA Form 1320-19, Directive Feedback Form
U S Department of Transportation
Federal Aviation Administration
Directive Feedback Information
Please submit any written comments or recommendation for improving this d1rect1ve, or suggest new items or subjects to be added to It Also, 1f you find an error, please tell us about It
Subject Order 8110 100B
To: Directives Management Officer at [email protected]
(Please check all appropriate /me items)
D An error (procedural or typographical) has been noted in paragraph ___ on
page __ _
D Recommend paragraph ___ on page ___ be changed as follows
(attached separate sheet ,t necessary)
D In a future change to this order, please include coverage on the following subject (briefly describe
what you want added)
D Other comments
D I would like to discuss the above Please contact me
Submitted by … Date …
Telephone Number … Routing Symbol …
FAA Form 1320-19 (10-98)