Radar Vectors
FAA Order Cancelled Issued Nov 1, 2002 AIR-230 167 pages Copy saved Nov 18, 2026

Order 8100.7C Aircraft Certification Systems Evaluation Program (ACSEP)

This document is cancelled. Cancelled by 8100.7D. Check the official source before relying on it.

Official source ↗ Open PDF

Distribution: A–W(IR)–3; A–X(CD)–3; A–FAC–0 (ALL); AMA–220 (5 copies); AFS–600 (3 copies); AEU–100 (ALL)

Initiated By: AIR–100/200

CHANGE

U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

ORDER 8100.7C

CHG 3

National Policy

Effective Date:

1/30/2009

SUBJ: Aircraft Certification Systems Evaluation Program

ORDER 8100.7C

1. Purpose. This change incorporates a modification to paragraph 55 and appendix 5, section 6, paragraph 1 to add a review of a sample of Production Approval Holder (PAH) supplier audit records. This change will allow the Aircraft Certification Systems Evaluation Program (ACSEP) evaluators to verify supplier compliance to quality requirements, corrective action, verification, and closure of those issues documented by the PAH. In addition, it will require the suppliers that are selected for review to be identified on the special emphasis page of the ACSEP report.

a. Paragraph 55, Evaluation of System Elements, was changed to add new subparagraph d, PAH Supplier Records. The new subparagraph provides information pertaining to the types of reports eligible for review, the method of documentation of the reports reviewed, supplier identification, and noted noncompliances. Paragraph 55d also establishes the purpose of the results for use in later evaluations.

b. Appendix 5, section 6, paragraph 1, Supplier Control, was changed to add subparagraphs a, Review of PAH supplier audit records; b, Recording Reviews; and c, Recording Noncompliances. These new subparagraphs provide information to the evaluator regarding the number of supplier reports to be reviewed and the method and detail for documenting results.

2. Who This Change Affects. This change to Order 8100.7C will be used by the following offices during the conduct of an ACSEP activity or during training: the Washington headquarters branch levels of the Aircraft Certification Service, the branch level in the directorate Aircraft Certification Service divisions, all Aircraft Certification Service offices, the Aircraft Certification Service branch at the Federal Aviation Administration Academy, the Regulatory Support Division of the Flight Standards Service, and the Brussels Aircraft Certification Branch.

3. Disposition of Transmittal Paragraph. Retain this transmittal sheet until the directive is cancelled by a new directive.

8100.7C CHG 3 1/30/2009

ii

PAGE CHANGE CONTROL CHART Remove Pages Dated Insert Pages Dated iii 10/12/2005 iii 10/12/2005 iv 10/12/2005 iv 1/30/2009 25 5/29/2008 25 1/30/2009 26 10/12/2005 26 1/30/2009 27 5/29/2008 27 1/30/2009 28 thru 29 10/12/2005 28 thru 36 1/30/2009 30 thru 31 11/26/2007 32 thru 34 10/12/2005 APPENDIX 5 73 thru 84 10/12/2005 APPENDIX 5 73 thru 84 1/30/2009

/s/ Frank P. Paskiewicz Manager, Production and

Airworthiness Division, AIR-200

Distribution: A-W (IR/FS/VN) -3; A-X (CD/FS) -3; A-FFS-0 (MAX); A-FAC- 0 (LTD); AMA-220 (10 copies); AMA-250 (10 copies); AFS-600 (3 copies); AVR-20 (LTD); AEU-00/200

Initiated By: AIR-200

CHANGE

U.S. DEPARTMENT OF TRANSPORTATION

U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

ORDER 8100.7C

CHG 2

National Policy

Effective Date: May 29, 2008

SUBJ: Aircraft Certification Systems Evaluation Program

1. Purpose. This change incorporates a modification to paragraph 42 a, and paragraph 43 to revise the minimum notification time from 90 days to 60 days. This change will allow the appropriate notification to occur within the stated time for evaluations that are scheduled in the months immediately following the latest release date of the annual schedule established in paragraph 33 d. The change also removes the requirement for the notification to be in writing or be documented.

ORDER 8100.7C

a. Paragraph 42 a., Lead Evaluation Office, page 21, was changed to remove the requirement for written notification and to establish that the notification does not need to be documented. The minimum notification time was changed to at least 60 calendar days before each directorate evaluation.

b. Paragraph 43, ACO, MIO, MIDO, and CMO Managers, page 21, was changed to remove the requirement for written notification and to change the minimum notification time to at least 60 calendar days. This paragraph was also changed to establish that the notification does not need to be documented.

2. Who This Change Affects. This order is distributed to the Washington Headquarters division levels of the Aircraft Certification Service and Flight Standards Service; to the branch levels of the Aircraft Certification Service; to the branch levels in the regional Flight Standards Divisions and Aircraft Certification Directorates; to all Flight Standards District Offices and International Field Offices; to all Aircraft Certification Offices (ACO); to all Certificate Management Offices and all Manufacturing Inspection District and Satellite Offices; to the Aircraft Certification and Airworthiness Branches at the FAA Academy; and to the Flight Standards International Field Offices.

3. Disposition of Transmittal Paragraph. Retain this transmittal sheet until the directive is cancelled by a new directive.

8100.7C CHG 2 5/29/2008

ii

CHANGE CONTROL CHART Remove Pages Dated Insert Pages Dated

21/22 10/12/2005 21/22 5/29/2008

/s/ Frank Paskiewicz Manager, Production and Airworthiness Division

Distribution: A–W(IR)–3; A–X(CD)–3; A–FAC–0 (ALL); AMA–220 (5 copies); AFS–600 (3 copies); AEU–100 (ALL)

Initiated By: AIR–100/200

CHANGE U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

ORDER 8100.7C

CHG 1

National Policy

Effective Date:

11/26/2007

SUBJ: Aircraft Certification Systems Evaluation Program (ACSEP) 1. Purpose. This change is issued to reflect the implementation of revised certificate management guidance. As a result, certain guidance and procedures affecting evaluation team leader currency that are specific to ACSEP have been revised to reflect the number of evaluations conducted each fiscal year. Also the requirement for quarterly tabulation and transmittal of a summary of errors from ACSEP reports has been eliminated. 2. Who this change affects. This change to Order 8100.7C will be used by the following offices during the conduct of an ACSEP activity or during training: the Washington headquarters branch levels of the Aircraft Certification Service, the branch level in the regional Aircraft Certification Service divisions, all Aircraft Certification Service offices, the Aircraft Certification Service branch at the Federal Aviation Administration Academy, the Regulatory Support Division of the Flight Standards Service, and the Brussels Aircraft Certification Branch.

3. Disposition of Transmittal Paragraph. After filing the attached pages, this change transmittal should be retained.

PAGE CHANGE CONTROL CHART Remove Pages Dated Insert Pages Dated 11 10/12/05 11 10/12/05 12 10/12/05 12 11/26/07 29 10/12/05 29 10/12/05 30 10/12/05 30 11/26/07 31 10/12/05 31 11/26/07 32 10/12/05 32 10/12/05 /s/ John Hickey Director, Aircraft Certification Service

Distribution: A–W(IR)–3; A–X(CD)–3; A–FAC–0 (ALL); AMA–220 (5 copies); AEU–100 (ALL); AVR–20 (3 copies); AFS–600 (3 copies)

Initiated by: AIR–100/200

ORDER 8100.7C

AIRCRAFT CERTIFICATION SYSTEMS

AIRCRAFT CERTIFICATION SYSTEMS

EVALUATION PROGRAM

October 12, 2005

DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

RECORD OF CHANGES DIRECTIVE NO. 8100.7C

CHANGE TO BASIC SUPPLEMENTS OPTIONAL CHANGE TO BASIC SUPPLEMENTS OPTIONAL

FAA Form 1320-5 (6-80) USE PREVIOUS EDITION

CHANGE TO BASIC SUPPLEMENTS OPTIONAL CHANGE TO BASIC SUPPLEMENTS OPTIONAL

10/12/2005 8100.7C

Page i (and ii)

FOREWORD

This order provides guidance and assigns responsibility for the implementation of the Aircraft Certification Systems Evaluation Program. This program is a vital element within the Federal Aviation Administration (FAA) mission of continued operational safety. This program uses a team of FAA engineering, flight test, and manufacturing inspection personnel to evaluate control of FAA-approved type design after initial approval by the FAA at production approval holders (PAH) and associated facilities.

The program will determine whether production approval holders are meeting the applicable requirements of Title 14, Code of Federal Regulations (14 CFR) and complying with the procedures established to meet those requirements. It also will survey the application of standardized evaluation criteria not required by 14 CFR or FAA-approved data to identify national trends that may require development of new or revised regulations, policy, and guidance.

The program is dynamic and contains provisions for continuous improvement. All Aircraft Certification Service personnel participating in this program are strongly encouraged to identify difficulties in implementing this program and to recommend improvements to the National Certificate Management Improvement Team.

/s/ John Hickey Director, Aircraft Certification Service

10/12/2005 8100.7C

Page iii

TABLE OF CONTENTS

TABLE OF CONTENTS

CHAPTER 1. GENERAL

Paragraph Page

1. Purpose … 1 2. Distribution … 1 3. Cancellation … 2 4. Effective Date … 2 5. Explanation of Changes … 2 6. Definitions … 2 7. Forms … 4 8. Authority To Change This Order … 4 9. Relation to Other Directives … 4 10. Requests for Information … 4 11. Acronyms … 4 12. Scope … 4 13. Information Currency … 4 14. Deviations … 4 15. Records Management … 5 16. Reserved … 5

CHAPTER 2. ACSEP EVALUATOR APPOINTMENT AND TRAINING

CHAPTER 2. ACSEP EVALUATOR APPOINTMENT AND TRAINING

17. General … 7 18. Appointing Officials … 7 19. Criteria for Candidate Selection … 7 Figure 2–1. Criteria for Candidate Selection and Team Member Appointment … 8 20. Criteria for Appointment … 8 Figure 2–2. Criteria for Team Leader Appointment … 10 21. Review of Appointment … 11 22. Reinstatement of Evaluators Failing To Meet Appointment Review Criteria … 12 23.–30. Reserved … 12

CHAPTER 3. SELECTION AND SCHEDULING OF ACSEP EVALUATIONS

CHAPTER 3. SELECTION AND SCHEDULING OF ACSEP EVALUATIONS

31. ACSEP Evaluation Intervals … 13 32. Selection of Facilities To Be Evaluated … 13 33. Scheduling of ACSEP Evaluations … 13 34. Selection of ACSEP Evaluators … 15 Table 3–1. Selecting a PI or AE as an Evaluator … 17 35. AIR Joint Scheduling Committee … 18 36. Notification of Facilities To Be Evaluated … 19 37. Modifications to Scheduled Evaluations … 20 38. Nonscheduled ACSEP Evaluations … 20 39.–41. Reserved … 20

8100.7C CH 3 1/30/2009

Page iv

CHAPTER 4. ACSEP EVALUATION PROCEDURES

CHAPTER 4. ACSEP EVALUATION PROCEDURES

SECTION 1. ACSEP EVALUATION PREPARATIONS

Paragraph Page

42. Lead Evaluation Office … 21 43. ACO, MIO, MIDO, and CMO Managers … 21 44. Evaluation Team Leader or Principal Evaluator … 21 45. Evaluation Team Member … 23 46.–51. Reserved … 23

SECTION 2. CONDUCT OF THE EVALUATION

SECTION 2. CONDUCT OF THE EVALUATION

52. Team Leader or Principal Evaluator Coordination With Facility Representative ... 24 53. Preevaluation Team Meeting … 24 54. Preevaluation Conference … 24 55. Evaluation of System Elements … 25 56. Recording Noncompliances … 27 57. Evaluation Meetings … 27 58. Postevaluation Conference … 30 59.–61. Reserved … 30

SECTION 3. POSTEVALUATION ACTIVITIES

SECTION 3. POSTEVALUATION ACTIVITIES

62. Preparing the ACSEP Evaluation Report … 31 63. Quality Review of the ACSEP Evaluation Report … 31 64. Sending the ACSEP Evaluation Report … 32 65. Requesting Corrective Action … 33 66.–71. Reserved … 33

CHAPTER 5. ACSEP AND CMIS

72. Purpose … 34 73. Files … 34 74. Database Management … 34 75. Use of the Database … 35 76.–81. Reserved … 35

APPENDIX 1. ACRONYMS

APPENDIX 1. ACRONYMS

1. Applicability … 1

10/12/2005 8100.7C

Page v

APPENDIX 2. PREPARATION OF CLAUSES FOR CONTRACTS FOR SUPPORT SERVICES

Paragraph Page

1. Purpose … 1 2. Sample Clauses and Attachment … 1 Figure 1. Sample Certificate of Nondisclosure … 2

APPENDIX 3. PREPARATION OF THE NOTIFICATION LETTER TO A PAH OR ASSOCIATE FACILITY

APPENDIX 3. PREPARATION OF THE NOTIFICATION LETTER TO A PAH OR ASSOCIATE FACILITY

1. Purpose … 1 2. Information To Include in the Notification Letter … 1 Figure 1. Sample Paragraphs for the Notification Letter … 2 Figure 2. Sample FAA Form 8100–7, ACSEP Evaluation Customer Feedback Report … 3

APPENDIX 4. NOTIFICATION LETTER REQUIREMENTS

1. Purpose … 1 2. Description … 1 Figure 1. Notification Letter Requirements Summary … 1

APPENDIX 5. FORMAT FOR STANDARDIZED EVALUATION CRITERIA FOR PAHs AND ASSOCIATE FACILITIES

APPENDIX 5. FORMAT FOR STANDARDIZED EVALUATION CRITERIA FOR PAHs AND ASSOCIATE FACILITIES

Part A Standardized Evaluation Criteria for PAHs and Associated Facilities … 1 Sec. 1 Organizational Management … 3 Sec. 2 Design Control … 13 Sec. 3 Software Quality Assurance … 19 Sec. 4 Manufacturing Processes … 27 Sec. 5 Manufacturing Controls … 49 Sec. 6 Supplier Control … 73 Part B Preparation Instructions for FAA Form 8100-4, ACSEP Survey Sheet for Production Approval Holders … 85 Figure 1. Sample FAA Form 8100–4 … 86

APPENDIX 6. PREPARATION INSTRUCTIONS FOR FAA ACSEP EXECUTIVE SUMMARY

APPENDIX 6. PREPARATION INSTRUCTIONS FOR FAA ACSEP EXECUTIVE SUMMARY

1. Purpose … 1 2. Specific Guidance … 1 Figure 1. Sample Executive Summary for PAHs and Associate Facilities … 2 Figure 2. Sample Executive Summary for Facilities with No Noncompliances 3

8100.7C 10/12/2005

Page vi

APPENDIX 7. PREPARATION INSTRUCTIONS FOR ACSEP EVALUATION SPECIAL EMPHASIS ITEMS

APPENDIX 7. PREPARATION INSTRUCTIONS FOR ACSEP EVALUATION SPECIAL EMPHASIS ITEMS

Paragraph Page 1. Purpose … 1 2. Specific Guidance … 1 Figure 1. Sample ACSEP Evaluation Special Emphasis Items for PAHs and Associate Facilities …

2

APPENDIX 8. PREPARATION INSTRUCTIONS FOR ACSEP EVALUATION LESSONS LEARNED

APPENDIX 8. PREPARATION INSTRUCTIONS FOR ACSEP EVALUATION LESSONS LEARNED

1. Purpose … 1 2. Specific Guidance … 1 Figure 1. Sample ACSEP Evaluation Lessons Learned … 2

APPENDIX 9. PREPARATION INSTRUCTIONS FOR FAA FORM 8100–3, ACSEP EVALUATION REPORT, COVER PAGES

1. Purpose … 1 2. Preparing the Front of the Form … 1 Figure 1. Sample FAA Form 8100–3 (Front) … 2 3. Preparing the Back of the Form … 3 Figure 2. Sample FAA Form 8100–3 (Back) … 4

APPENDIX 10. PROCESS FOR SENDING ACSEP EVALUATION REPORTS

APPENDIX 10. PROCESS FOR SENDING ACSEP EVALUATION REPORTS

1. Purpose … 1 2. Description … 1 Figure 1. Process for PAHs and Associate Facilities … 1

10/12/2005 8100.7C

Par 1 Page 1

CHAPTER 1. GENERAL

1. PURPOSE.

a. This order establishes and describes the Federal Aviation Administration (FAA) Aircraft Certification Systems Evaluation Program (ACSEP). This program, an element of certificate management, is a vital element within the FAA’s mission of continued operational safety and is excluded from the Department of Transportation’s plan to reduce internal regulations by 50 percent. FAA Order 8120.2, Production Approval and Certificate Management Procedures, defines the entire certificate management program. However, there are processes in this order that are automated in the Certificate Management Information System (CMIS) program. All of these processes must be performed within CMIS. Other evaluations, audits, or inspections may be required in accordance with directorate or headquarters directives. The ACSEP is a comprehensive evaluation program that accomplishes the following:

CHAPTER 1. GENERAL

(1) Applies standardized systems evaluation to the continued integrity of the design data after initial approval by the FAA at production approval holders (PAH) and associate facilities. The ACSEP does not reevaluate the approval of previously approved data such as quality manuals and design data.

(2) Ascertains whether PAHs and associate facilities meet the applicable requirements of Title 14, Code of Federal Regulations (14 CFR) and comply with procedures established to meet those requirements.

(3) Surveys the application of standardized evaluation criteria not required by 14 CFR or FAA-approved data to identify national trends that may require development of new or revised regulations, policy, and guidance.

(4) Provides customer focus through the establishment of a database for analyzing evaluation results and for reporting trends in continued operational safety upon which FAA customers may act.

(5) Provides continuous improvement by continually evaluating lessons learned and customer feedback reports, and considering proposed improvements by FAA internal and external customers.

(6) Provides for employee involvement by establishing and maintaining a professional staff of trained evaluators composed of aviation safety inspectors, aerospace engineers, flight test engineers, and flight test pilots.

b. All processes defined in this order that are automated in the CMIS, must be performed in CMIS. Because CMIS automates some of the evaluation processes, there may be differences in CMIS processes and the stated manual processes defined in this order. Where this is the case, the automated process in CMIS takes precedence over the manual process stated in this order.

2. DISTRIBUTION. This order is distributed to the Washington headquarters branch levels of the Aircraft Certification Service, to the branch level in the regional Aircraft Certification Service divisions, to all Aircraft Certification Service offices, to the Suspected Unapproved Parts Program Office, to the Aircraft Certification Service branch at the Federal Aviation Administration Academy, to the Regulatory Support Division of the Flight Standards Service, and to the Brussels Aircraft Certification Branch.

8100.7C 10/12/2005

Page 2 Par 3

3. CANCELLATION. FAA Order 8100.7B, Aircraft Certification Systems Evaluation Program, dated November 1, 2002, and all associated changes are canceled.

4. EFFECTIVE DATE. All evaluation requirements and references related to delegated facilities have been removed effective November 11, 2005.

5. EXPLANATION OF CHANGES. The following significant changes are contained in this revision:

a. Removed all reference to delegated facilities from this order.

b. Renumbered appendixes because of the removal of appendix 7 regarding delegated facilities.

c. Added information on the use of the CMIS and when it is to be used.

6. DEFINITIONS. The following definitions apply to the conduct and administration of an ACSEP:

a. Assigned Engineer (AE). An FAA engineer to whom the Aircraft Certification Office (ACO) manager has assigned responsibility for an ACSEP evaluation at a particular design approval facility.

b. Associate Facility. A facility approved as an extension to a PAH. The facility is owned and operated by the same corporate management as the original PAH that controls the design and quality of the product/part thereof, except for companies participating in joint-production and/or coproduction business agreements. The associate facility must be listed as a manufacturing facility on the production certificate (PC) or letter of authorization for other production approvals, for example, a parts manufacturer approval (PMA) or technical standard order (TSO) authorization.

c. Certificate Management Information System (CMIS). Electronic data system that incorporates several aspects of Certificate Management functions. Functions available within CMIS are certification management tasks, and the planning, scheduling and conducting of evaluations.

d. Established Industry Practice. A widely followed method of operating that achieves consistent performance of specific functions. Examples of established industry practices include a calibration recall system and an internal audit system.

e. Evaluator. An individual the FAA appoints to perform ACSEP evaluations.

f. FAA-Approved Data. Data specifically approved by the FAA or FAA-delegated representatives, including any document referenced therein. These data may include design drawings, manuals, procedures, and specifications.

g. Facility. A physical location where a PAH or associate facility performs all or part of the system element functions relevant to the approval authority granted by the FAA.

h. Geographic Manufacturing Inspection District Office (MIDO) or Certificate Management Office (CMO). An MIDO or CMO that performs certificate management of an associate facility located in its geographical area of responsibility on the basis of a request from another MIDO or CMO.

10/12/2005 8100.7C

Par 6 Page 3

i. Lead Evaluation Office. A directorate office or branch assigned to coordinate an ACSEP evaluation.

j. Noncompliance. A PAH’s or associate facility’s operating practice found to be inconsistent with 14 CFR, FAA-approved data, or internal procedures. A supplier’s operating practice found to be inconsistent with a PAH’s or associate facility’s purchase order requirements is considered to be a noncompliance by the PAH or associate facility. Refer to Order 8120.2 for an explanation of the four types of noncompliance.

k. Objective Evidence. All the means by which any alleged fact tends to be established or disproved. These means must be factual, convincing, relevant, valid, reliable, and complete. Examples of objective evidence include interview statements, photographs, charts, maps, diagrams, documents, and records. Documents and records include items such as work travelers, inspection documents, FAA-approved drawings, PMA and TSO approval letters, airworthiness approval tags (FAA Form 8130–3, Airworthiness Approval Tag), and calibration logs.

l. Principal Evaluator. An FAA-appointed team leader who acts as the sole evaluator for the performance of an ACSEP evaluation at a specific facility.

m. Principal Inspector (PI). A manufacturing inspector who has been assigned certificate management responsibility of a particular PAH or associate facility.

n. Procedure. A specific way to perform an activity or function that is documented and usually contains the purposes and scope of the activity or function: what is to be done and by whom; when, where, and how the activity or function is to be done; the materials, equipment, and documents to be used; and how the activity or function is to be controlled and recorded.

o. Production Approval Holder (PAH). The holder of a PC, Approved Production Inspection System (APIS), PMA, or TSO authorization, who has primary responsibility to control the design and quality of a product or part thereof.

p. Requesting MIDO or CMO. An office that requests associate facility certificate management from another office having geographic responsibility of the area in which the facility is located.

q. Resource Targeting. A method of grouping and categorizing PAHs and associate facilities that provides for effective FAA certificate management resource deployment.

r. Standardized Evaluation Criteria. Questions developed for each system element that FAA ACSEP evaluation teams use to plan and document the evaluation. The applicable 14 CFR requirements, appropriate FAA advisory circulars (AC) and directives, international standards and specifications, and established industry practices are the basis for these questions. Refer to appendixes 6 and 7.

s. System. An activity or function that may affect the maintenance of an FAA-approved design, quality data, or the design approval system.

8100.7C 10/12/2005

Page 4 Par 6

t. System Element. A specific activity or function that may affect the maintenance of FAA-approved design or quality data, such as design data control, manufacturing controls, and supplier control. Such activities are subject to evaluation of the adequacy and implementation of approved procedures.

7. FORMS. All forms used in the performance and administration of ACSEP evaluations are provided by the Production Airworthiness Division (AIR–200) in electronic format as found in the CMIS program.

8. AUTHORITY TO CHANGE THIS ORDER. The issuance, revision, or cancellation of the material in this order is the responsibility of the AIR Aircraft Engineering Division (AIR–100) and AIR–200. These divisions will accomplish all changes, as required, to carry out the FAA’s responsibility to provide for evaluations of PAHs.

9. RELATION TO OTHER DIRECTIVES. Orders referenced in this directive list only the basic order number. The user must establish that the latest revision/amendments are being used.

10. REQUESTS FOR INFORMATION. All public requests for information regarding completed ACSEP and non-ACSEP evaluations and related database information will be processed in accordance with the Freedom of Information Act (refer to FAA Order 1270.1, Freedom of Information Act Program).

11. ACRONYMS. Acronyms are listed in appendix 1 to this order.

12. SCOPE. The ACSEP will evaluate all PC, APIS, PMA, and TSO authorization holders, and their associate facilities assessed as category 1 and 2 facilities in resource targeting groups I through III. See Order 8120.2. PAHs assessed by resource targeting as category 3 facilities, suppliers, and holders of a letter of TSO design approval are not subject to the ACSEP. However, the ACSEP team leader may extend an ACSEP evaluation at a PAH to key suppliers, and subtier suppliers or processors to verify the PAH is satisfactorily controlling its suppliers. The AIR directorates will implement the ACSEP. AIR–100 and AIR–200 will support the ACSEP.

13. INFORMATION CURRENCY. Any deficiencies found, clarifications needed, or improvements to be suggested regarding the content of this order should be forwarded to the Planning and Financial Resources Management Branch, AIR–530, Attention: Directives Management Officer, for consideration. Your assistance is welcome. FAA Form 1320–19, Directive Feedback Information, is located on the last page of this order for your convenience. If an interpretation is urgently needed regarding evaluations at PAHs, contact the Evaluations and International Programs Branch, AIR–230, at 202–267–8361. Also use Form 1320–19 as a followup to any verbal conversation.

14. DEVIATIONS. Adherence to the procedures in this order is necessary for uniform administration of this directive material. If a deviation becomes necessary, the FAA employee involved must ensure the deviations are substantiated, documented, and concurred with by the appropriate supervisor. The deviation must be submitted to AIR–100 and AIR–200 for review and approval. The limits of Federal protection for FAA employees are defined by Title 28, United States Code § 2679.

10/12/2005 8100.7C

Par 15 Page 5 (and 6)

15. RECORDS MANAGEMENT. For guidance regarding retention or disposition of records, consult your office Records Management Officer/Directives Management Officer or refer to FAA Order 0000.1, FAA Standard Subject Classification System, FAA Order 1350.14, Records Management, and FAA Order 1350.15, Records Organization, Transfer, and Destruction Standards.

16. RESERVED.

10/12/2005 8100.7C

Par 17 Page 7

CHAPTER 2. ACSEP EVALUATOR APPOINTMENT AND TRAINING

CHAPTER 2. ACSEP EVALUATOR APPOINTMENT AND TRAINING

17. GENERAL. The appointing officials designated in paragraph 18 will select ACSEP evaluator candidates who have attained a specified level of experience, or a combination of experience and education, as engineers, flight test pilots, or aviation safety inspectors, and who have demonstrated technical knowledge and skills. A candidate will receive formal classroom ACSEP evaluation training and serve as an evaluator-in-training during ACSEP evaluations under the direct supervision of an appointed ACSEP team leader, before appointment as an ACSEP evaluation team member. Before appointment, a candidate for evaluation team leader will have participated in ACSEP evaluations as an appointed team member and will perform as a team leader-in-training under the direct supervision of an appointed ACSEP team leader. Both evaluation team members and leaders will be subject to periodic reevaluation by the cognizant appointing official.

18. APPOINTING OFFICIALS. The following directorate and headquarters managers are authorized to select ACSEP evaluator candidates and to appoint qualified candidates as ACSEP team members or team leaders within their respective organizations:

a. ACO managers and ACO branch managers.

b. Manufacturing inspection office (MIO), MIDO, and CMO managers.

c. Directorate Standards Staff managers.

d. AIR–100 manager.

e. AIR–200 manager.

19. CRITERIA FOR CANDIDATE SELECTION. The appointing official will select engineering, flight test or aviation safety inspector candidates on the basis of the following criteria (see figure 2–1):

a. Candidates have attained at least one of the following specified levels of experience or a combination of experience and education in their specific disciplines:

(1) At least 8 years of technical experience in aerospace manufacturing or design, or in the evaluation thereof.

(2) Technical or trade school certificate with 6 years of technical experience in aerospace manufacturing or design, or in the evaluation thereof.

(3) Associate’s degree in engineering or science disciplines, with 5 years of technical experience in aerospace manufacturing or design, or in the evaluation thereof.

(4) Bachelor’s degree or higher in engineering or science disciplines, with 3 years of technical experience in aerospace manufacturing or design, or in the evaluation thereof.

8100.7C 10/12/2005

Page 8 Par 19

FIGURE 2–1. CRITERIA FOR CANDIDATE SELECTION

FIGURE 2–1. CRITERIA FOR CANDIDATE SELECTION

AND TEAM MEMBER APPOINTMENT

8 years technical experience in aerospace

mfg. or design, or

evaluation?

Tech or trade school certificate +6 yrs tech experience in aerospace mfg. or design,

or evaluation?

No

Assoc degree in Engineering or Science +5 yrs tech experience in

AND TEAM MEMBER APPOINTMENT

aerospace mfg. or design,

or evaluation?

No

Bachelor's degree in Engineering or Science

+3 yrs tech experience in aerospace mfg. or design,

or evaluation?

No

Satisfactory completion of ACSEP

training course?

CANDIDATE NOT

ELIGIBLE FOR APPOINTMENT

No

Yes Yes Yes Yes

Participation in at least 2 ACSEP evaluations as an evaluator-in-training?

ELIGIBLE FOR APPOINTMENT

Yes

Yes

CANDIDATE ELIGIBLE FOR APPOINTMENT AS ACSEP TEAM MEMBER

No

No

b. Candidates have demonstrated technical knowledge in aerospace manufacturing or design, conceptual understanding of FAA goals and objectives, effective communication and interpersonal skills, good human relations, and coherent writing ability.

CANDIDATE ELIGIBLE FOR APPOINTMENT AS ACSEP TEAM MEMBER

20. CRITERIA FOR APPOINTMENT. Appointment is the formal process of certifying an ACSEP candidate as an ACSEP team member or team leader on the basis of successful completion of all requirements (see figures 2–1 and 2–2).

a. Team Member. Candidates must meet the following minimum requirements before appointment as a team member (see figure 2–1):

(1) Satisfactory completion of the ACSEP team training course and written examination. The course will provide training in the policy established in this order, including the techniques for applying the standardized evaluation criteria contained in appendixes 6 and 7, and in coordinating team member involvement.

NOTE: The Planning and Program Management Division, AIR–500, will ensure classes are scheduled on the basis of service priorities as given in the training requirements process.

10/12/2005 8100.7C

Par 20 Page 9

(2) Participation of the candidate, and demonstration of the knowledge and skills acquired during ACSEP team training in at least two ACSEP evaluations as an evaluator-in-training.

NOTE: The candidate’s appointing official must schedule the candidate’s participation as an evaluator-in-training to be completed in as short a timeframe as possible to maximize the candidate’s use and retention of acquired knowledge and experience.

(3) The candidate’s appointing official is responsible for performing the following activities in evaluating the team member candidate:

(a) Consider the candidate’s previous experience and education.

(b) Consider the product complexity, facility size, and complexity of system elements evaluated in ACSEP evaluations in which the candidate participated.

(c) Discuss with team leader(s) of evaluations in which the candidate participated to determine the candidate’s ACSEP evaluation readiness.

(d) Review ACSEP evaluation reports for evaluations in which the candidate participated.

(e) Review, when necessary, FAA Form(s) 8100–7, ACSEP Evaluation Customer Feedback Report, for evaluations in which the candidate participated.

(f) Interview the candidate.

(g) Discuss with the candidate any weaknesses or deficiencies in his or her evaluation readiness identified during the participation phase. Both parties will work to reduce or eliminate these weaknesses or deficiencies through additional training, additional ACSEP evaluations, National Aviation Safety Inspection Program/Regional Aviation Safety Inspection Program audits, or other similar activities that will increase the candidate’s evaluation readiness.

(4) On the basis of satisfactory results of the evaluation of the candidate as listed in paragraph 20a(3), the candidate’s appointing official will appoint the candidate as a team member.

b. Team Leader. Candidates must meet the following minimum requirements before appointment as a team leader (see figure 2–2):

(1) Current appointment as an ACSEP evaluation team member.

(2) Participation in at least three evaluations as an appointed ACSEP evaluation team member. The candidate’s appointing official may request reduction of the requirement by providing documented justification to the appointing official’s manager. The responsibility for requesting any reduction of the requirement rests solely with the candidate’s appointing official.

8100.7C 10/12/2005

Page 10 Par 20

FIGURE 2–2. CRITERIA FOR TEAM LEADER APPOINTMENT

FIGURE 2–2. CRITERIA FOR TEAM LEADER APPOINTMENT

Appointment as

ACSEP Team

Member?

Participated in at least 3 evaluations as a

team member?

Yes

Written justification from appointing official

for reduction of

requirement?

No

CANDIDATE NOT

ELIGIBLE FOR APPOINTMENT

No

Participated in at least 3 evaluations

ELIGIBLE FOR APPOINTMENT

as a team leader-in-

training?

Yes Manager approval?

Yes

Yes

No

Written justification from appointing official

for reduction of

requirement?

Manager approval?

Yes

No No

No

CANDIDATE ELIGIBLE FOR APPOINTMENT AS

ACSEP TEAM LEADER

Yes

Yes

No

(3) Participation as a team leader-in-training, and demonstration of knowledge and skills acquired during ACSEP team training in at least three ACSEP evaluations under the direct supervision of an appointed ACSEP evaluation team leader. The candidate’s appointing official may request reduction of the requirement by providing documented justification to the appointing official’s supervisor. The responsibility for requesting any reduction of the requirement rests solely with the candidate’s appointing official.

ACSEP TEAM LEADER

NOTE: The candidate’s appointing official must schedule the candidate’s participation as a team leader-in-training to be completed in as short a timeframe as possible to maximize the candidate’s use and retention of acquired knowledge and experience.

10/12/2005 8100.7C

Par 20 Page 11

(4) The candidate’s appointing official is responsible for performing the following activities in evaluating the team leader candidate:

(a) Consider the candidate’s previous experience and education.

(b) Consider the product complexity, facility size, and complexity of system elements evaluated in ACSEP evaluations in which the candidate participated.

(c) Discuss with team leader(s) of evaluations in which the candidate participated to determine the candidate’s team leadership abilities.

(d) Review ACSEP evaluation reports for evaluations in which the candidate participated.

(e) Review, when necessary, FAA Form(s) 8100–7 for evaluations in which the candidate participated.

(f) Interview the candidate.

(g) Discuss with the candidate any weaknesses or deficiencies in their team leadership abilities identified during the participation phase. Both parties will work to reduce or eliminate these weaknesses or deficiencies through additional training, additional ACSEP evaluations, National Aviation Safety Inspection Program/Regional Aviation Safety Inspection Program audits, or other similar activities that will increase the candidate’s leadership abilities.

(5) On the basis of satisfactory results of the evaluation of the candidate as listed in paragraph 20b(4), the candidate’s appointing official will appoint the candidate as a team leader.

c. The candidate’s appointing official will document and track the completion of the requirements in paragraphs 20a and 20b for all ACSEP candidates. Upon successful completion of the requirements, the appointing official will appoint the candidate as an ACSEP evaluation team leader or team member and will formally notify the candidate of his or her appointment in writing. Ensure the appointment document includes the individual’s discipline and office identification.

NOTE: Provide written notification of appointment before the evaluator’s first scheduled ACSEP evaluation as a team member or team leader.

21. REVIEW OF APPOINTMENT. The cognizant appointing official (1) reviews the participation in ACSEP evaluations by each evaluator under their appointment authority, (2) notifies evaluators in writing of decisions not to continue their appointment, and (3) determines the currency and continued validity of appointments as follows.

a. Evaluation Team Members. Review evaluation team members’ participation annually. Ensure team members have accomplished the following requirements, as a minimum:

(1) Participated at an interval of once or more every 2 fiscal years as an ACSEP evaluation team member or team leader, or conducted PI or district office audits in accordance with Order 8120.2.

NOTE: A supplier control audit does not count toward the continued appointment of an ACSEP team member.

8100.7C 11/26/2007

Page 12 Par 21

(2) Demonstrated knowledge and skill in ACSEP evaluations, as determined from sources such as the ACSEP evaluation report, team leaders, cognizant managers, and satisfactory corrective action for any shortcomings in knowledge or skills noted and discussed with the team member during the interim period.

b. Evaluation Team Leaders. Review evaluation team leaders’ participation annually. Ensure team leaders have accomplished the following requirements, as a minimum:

(1) Participated at an interval of once or more during a 2-fiscal-year period as an ACSEP evaluation team leader or as a team leader for a PI or district office audit with multiple team members in accordance with Order 8120.2.

NOTE: A supplier control audit does not count toward the continued appointment of an ACSEP team leader.

(2) Demonstrated knowledge and skill in ACSEP evaluations, as determined from sources such as the ACSEP evaluation report, cognizant managers, and satisfactory corrective action for any shortcomings in knowledge or skills noted and discussed with the team leader during the interim period.

22. REINSTATEMENT OF EVALUATORS FAILING TO MEET APPOINTMENT REVIEW CRITERIA. Cognizant appointing officials may reinstate evaluators under their appointment authority who have not met the appointment review criteria listed in paragraph 21. Use the following criteria to determine eligibility for reinstatement:

a. Team members and leaders who have not met participation requirements may be reinstated after acceptable participation as an evaluator-in-training, or as a team leader-in-training as applicable, in two ACSEP evaluations.

b. Team members who have not demonstrated ACSEP evaluation knowledge or skills may be considered for reinstatement by repeating the formal ACSEP team member appointment program listed in paragraph 20a.

c. Team leaders who have not demonstrated ACSEP evaluation knowledge or skills may be reinstated as a team member after acceptable participation as an evaluator-in-training in two ACSEP evaluations. Consideration for reinstatement as a team leader must then follow the formal ACSEP team leader appointment program listed in paragraph 20b.

23.–30. RESERVED.

10/12/2005 8100.7C

Par 31 Page 13

CHAPTER 3. SELECTION AND SCHEDULING OF ACSEP EVALUATIONS

CHAPTER 3. SELECTION AND SCHEDULING OF ACSEP EVALUATIONS

31. ACSEP EVALUATION INTERVALS. Evaluation intervals for PAHs and associate facilities are identified in Order 8120.2.

32. SELECTION OF FACILITIES TO BE EVALUATED. Procedures for selecting PAHs and associate facilities to be evaluated are identified in Order 8120.2.

33. SCHEDULING OF ACSEP EVALUATIONS. After all facilities have been selected for evaluation in accordance with paragraph 32, each directorate will be responsible for scheduling ACSEP evaluations at the selected facilities. Use the following procedures:

a. Estimate the onsite duration of each evaluation according to the evaluation interval listed in paragraph 31. Consider the quality and/or engineering procedures and processes required to be in place, the number of applicable system elements, when known (see appendix 5), the size and physical layout of the facility to be evaluated (single or multiple locations), and product complexity. Allow enough time to ensure that compliance to the applicable 14 CFR and FAA-approved data will be fully evaluated. Use the following list as a guide for estimating, in terms of only facility size, the onsite duration of the evaluation (excluding travel times):

(1) Small facility with less than 100 total full-time persons: 1 to 5 working days onsite.

(2) Medium facility with 100 to less than 400 total full-time persons: 3 to 5 working days onsite.

(3) Large facility with 400 to less than 2,000 total full-time persons: 5 to 10 working days onsite.

(4) Very large facility with 2,000 or more total full-time persons: 7 to 15 working days onsite.

NOTE: When estimating the onsite duration, include only those persons who are used to support the PAH activity.

b. Assign all scheduled evaluations a distinct ACSEP number, consisting of the fiscal year, directorate code (NE—Engine and Propeller Directorate, CE–Small Airplane Directorate, SW—Rotorcraft Directorate, or NM—Transport Airplane Directorate), and the evaluation order sequence. For example, 00CE123 represents the 123rd evaluation planned for completion by the Small Airplane Directorate during fiscal year 2000. Some of the scheduled evaluations will be identified at the AIR Joint Scheduling Committee meeting as evaluations to be led by AIR–200, in accordance with paragraph 35.

NOTE: Do not reassign ACSEP numbers from canceled evaluations. Each scheduled evaluation must be uniquely identified.

8100.7C 10/12/2005

Page 14 Par 33

c. Identify the lead evaluation office for each evaluation. This office is usually the one that performs certificate management responsibility at the facility to be evaluated. For an associate facility subject to certificate management under the handoff procedure described in Order 8120.2, the lead evaluation office is the geographic office receiving the handoff. The lead evaluation office is responsible for—

(1) Coordinating the notification letter (see paragraph 36), and

(2) Notifying the selected team leader and team members (see paragraph 42).

d. Prepare an evaluation schedule for 1 fiscal year based on the facility selection criteria in paragraph 32 and the duration of each evaluation. Annually prepare the schedule no later than July 31.

(1) Prepare the schedule in quarterly increments using the following guidelines:

(a) ACSEP number.

(b) Scheduled start date of each evaluation.

(c) Duration of each evaluation.

(d) Facilities and types of approvals to be evaluated.

(e) Resource targeting group assignment, as applicable.

(f) Product lines or authorized functions at the facilities to be evaluated.

(g) Number and disciplines of evaluators assigned to each evaluation.

(h) Additional evaluators required beyond the directorate’s resources.

(i) Number and disciplines of evaluators-in-training and team leaders-in-training.

(j) Total number of evaluations scheduled by quarter and for the fiscal year.

(k) Applicable project number(s).

(2) To facilitate the merging of directorate schedules into a master schedule, as required by paragraph 35, AIR–200 will provide a common software format to the ACO, MIO, MIDO, and CMO managers for documenting the items listed in paragraph 33d(1).

(3) The ACO, MIO, MIDO, and CMO managers should schedule approval holders having multiple approvals, such as a PC and a PMA, so as to evaluate all approvals during one evaluation.

(4) When an approval holder has multiple facilities that require significant resources and time to evaluate, the ACO, MIO, MIDO, and CMO managers should consider scheduling the facilities individually.

10/12/2005 8100.7C

Par 33 Page 15

e. Designate an assigned engineer. On the basis of the data collected for paragraphs 31 through 33d, the ACO manager determines the need to assign an FAA engineer responsibility relating to a scheduled ACSEP evaluation at a particular design approval facility. The AE must answer questions from the evaluators regarding the FAA-approved design or the design approval system in place. The AE also must coordinate any corrective action required regarding the FAA-approved design or the design approval system.

34. SELECTION OF ACSEP EVALUATORS. The ACO, MIO, MIDO, and CMO managers select appointed ACSEP evaluators to perform each scheduled evaluation. Determine the number and types of evaluators required for each evaluation according to the following criteria:

a. Number of Evaluators Required. Determine the total number of evaluators required to ensure that compliance to the applicable 14 CFR and FAA-approved data would be fully evaluated.

(1) Estimate the number of evaluators required according to the following minimum criteria:

(a) Resource targeting group assigned for type of facility.

(b) Number and complexity of applicable quality, engineering, flight test, and facility procedures and processes in place.

(c) Number of applicable system elements, when known (see appendix 5).

(d) Number of suppliers to which the evaluation will be extended, when known.

(e) Size and physical layout of the facility to be evaluated (single or multiple locations).

(f) Product or design approval system complexity.

(2) Use the following as a guide for estimating the number of ACSEP evaluators required. Increase or decrease the number of estimated evaluators shown below, depending on your review of the criteria contained in paragraph 34a(1) and your confidence that compliance to the applicable 14 CFR and FAA-approved data will be fully evaluated:

(a) Small facility with less than 100 full-time persons: 1 to 3 evaluators (including team leader).

(b) Medium facility with 100 to less than 400 total full-time persons: 1 to 5 evaluators (including team leader).

(c) Large facility with 400 to less than 2,000 total full-time persons: team leader plus 5 to 10 evaluators.

8100.7C 10/12/2005

Page 16 Par 34

(d) Very large facility with 2,000 or more total full-time persons: team leader plus up to 10 evaluators.

NOTE: When estimating the number of evaluators required, include only those full-time persons who are used to support the PAH facility activity.

(3) If it is determined that one evaluator is required, select an appointed team leader to perform the evaluation; this evaluator is referred to as the principal evaluator. If two or more evaluators are selected for an evaluation, they will constitute an ACSEP evaluation team. Select an appointed team leader and the required number of appointed team members.

b. Types of Evaluators Required. Use the criteria identified in paragraphs 34a(1)(a) through (f) and the following criteria to determine the types of evaluators required:

(1) Select appointed ACSEP evaluators who have appropriate knowledge of the evaluation criteria identified in appendix 5 applicable to the facility to be evaluated and, as appropriate, to the product(s) authorized by the approval (for example, select a propulsion engineer when an engine manufacturer is to be evaluated and select a flight test pilot when a flight test program is to be evaluated). When making this determination, consider the following:

(a) It is not necessary to select both engineers and inspectors for a small facility that does not have both engineering and manufacturing capabilities.

(b) Select appointed ACSEP evaluators, as appropriate, to maintain continued appointment in accordance with paragraph 21.

(c) Do not include any appointed evaluators who were previously employed by the facility to be evaluated within 2 years of the scheduled evaluation.

(d) Determine whether evaluators will be made available throughout the duration of the evaluation. Each evaluator is expected to fully participate in each evaluation. Base any decision to limit participation on the established AIR priorities. Notify the team leader of any limited participation by evaluators.

(2) For evaluations led by AIR–200, the AIR Joint Scheduling Committee identifies general team compositions during its annual meeting or telephone conference, on the basis of the ACSEP master schedule (refer to paragraph 35). The ACO, MIO, MIDO, CMO, and AIR–200 managers select appointed ACSEP evaluators to fill these requirements using the criteria listed in paragraph 34b(1).

10/12/2005 8100.7C

Par 34 Page 17

c. Selection of PI and AE as Team Leaders or Evaluators. To the greatest extent practicable, the PI and the AE will not be selected as team leaders on ACSEP evaluations of facilities for which they have certificate management or surveillance responsibilities. Use the guidelines in table XX to select the PI and/or AE as evaluators:

Table 3–1. Selecting a PI or AE as an Evaluator

Number of Persons Performing the Evaluation PAH Facility Procedure

One- or two-person Do not select the responsible certificate management PI. Do not select the AE if the AE is the engineer assigned design responsibility for the facility to be evaluated.

NOTE: For evaluations with at least three team members, the ACO, MIO, MIDO, and CMO managers, to the greatest extent practicable, will select as evaluators the PI, or assistant PI as appropriate, and/or the AE. The ACO, MIO, MIDO, and CMO managers should assess the logistical and personal burden of selecting the PI and/or AE for all applicable evaluations, and should assign the PI and/or AE to evaluations through which the greatest benefit may be obtained. Three- or four-person Select as a team member either the responsible certificate management PI or the AE, if the AE is the engineer assigned design responsibility for the facility to be evaluated. If the AE is not assigned design responsibility, both the AE and the responsible certificate management PI may be selected as team members. Five-person or greater Select as a team member either the responsible certificate management PI or AE, or both.

d. Selection of Evaluators-in-Training and Team Leaders-in-Training.

(1) Determine the number of appointed evaluators required for the ACSEP evaluation before assigning evaluators-in-training. Assign evaluators-in-training only to evaluations for which a team is required. Do not assign evaluators-in-training to a principal evaluator. Evaluators-in-training will supplement appointed evaluators. Do not substitute evaluators-in-training for appointed ACSEP evaluators, or evaluation team leaders-in-training for appointed ACSEP evaluation team leaders.

(2) Do not assign more than two evaluators-in-training or more than one team leader-in-training to any one evaluation. Try to assign each evaluator-in-training or team leader-in-training to different team leaders during the participation phase of the training.

(3) In cases where evaluators-in-training or team leaders-in-training from other directorates or AIR–100/200 are proposed to be used in an evaluation, coordinate with the appointing managers to establish their eligibility.

8100.7C 10/12/2005

Page 18 Par 34

e. Additional Resource Requirements. Additional evaluators beyond the directorate’s available resources may be required depending on the size of the facility; type and complexity of product, service, or design approval system; and overall evaluation objectives. Each directorate should present these additional resources during the Joint Scheduling Committee meeting as indicated in paragraph 35. For resource requirements identified after the Joint Scheduling Committee meeting, the directorate should request additional support from other areas of AIR. If these sources of support are not available, the directorate may obtain outside support services to augment directorate resources. Criteria for obtaining outside support service personnel are included in paragraph 35a(2).

35. AIR JOINT SCHEDULING COMMITTEE. The Joint Scheduling Committee is composed of the ACSEP headquarters project manager and an ACO and MIO manager from each directorate. When a directorate has appointed a certificate management coordinator, the directorate may assign that coordinator to the committee in place of an ACO and MIO manager. However, the certificate management coordinator must have the authority to commit resources and adjust schedules as necessary. The ACSEP headquarters project manager is the chairperson of the committee. The committee must coordinate the directorates’ annual evaluation schedules into an ACSEP master schedule, coordinate additional resources required, and identify the general team compositions to support evaluations led by AIR–200.

a. After each of the directorates prepares an updated annual evaluation schedule, the ACSEP headquarters project manager will convene a meeting or telephone conference of the Joint Scheduling Committee. The committee will accomplish the following tasks:

(1) The committee must identify general team compositions for evaluations to be led by AIR–200 as follows:

(a) Team leader from AIR–200.

(b) Team members from the directorate responsible for the facility to be evaluated, to the extent practicable, on the basis of the number of evaluators previously identified on the directorate’s evaluation schedule.

(c) When needed, the balance of the team members from other areas of AIR on the basis of the ACSEP master schedule.

(2) After the ACSEP master schedule is coordinated and the AIR–200-led evaluations are staffed, the committee must review any directorate requests for additional evaluation team members required to support the evaluations. The committee will identify available resources from other areas of AIR. If these sources of support are not available, the committee may recommend the use of outside support services to augment directorate resources. Support service personnel will be qualified and creditable quality assurance experts and technology specialists and will meet the criteria for candidate selection specified in paragraph 19. Directorates will obtain any required support service personnel in accordance with budgetary directives. Appendix 2 contains sample contract clauses relating to obtaining support services.

10/12/2005 8100.7C

Par 35 Page 19

NOTE: The cognizant directorate will complete all necessary administrative measures required for facility access by support service personnel before the scheduled ACSEP evaluation. The measures may include obtaining any security clearances from the prospective facility, ensuring personnel have signed a certificate of nondisclosure for confidentiality of information (see appendix 2), and ensuring personnel are aware of their limitations (as agreed to between the directorate and the facility to be evaluated) of access and entry to the facility’s proprietary or sensitive processes or systems.

(3) AIR–200 must transcribe all schedules and related decisions into written committee proceedings and provide one copy to each directorate and AIR–100.

b. Each directorate must transmit schedule changes electronically to AIR–200 at least monthly. Evaluations added to the master schedule will be assigned a new ACSEP number in accordance with paragraph 33b. AIR–200 will maintain the master schedule and update it quarterly.

36. NOTIFICATION OF FACILITIES TO BE EVALUATED. The lead evaluation office identified in accordance with paragraph 33c will notify facilities using the sample formats in appendixes 3 and 4. Coordinate with the responsible PI to ensure the letter does not arrive during scheduled shutdown periods or during any other extended periods when the letter may not be acted upon. For notifications of first-time ACSEP evaluations, inform the facility that ACSEP reference material is available on the FAA’s Web site and AIR’s Regulatory and Guidance Library Web site. If the facility cannot access these Web sites, provide the reference material to the facility. Appendix 4 provides a summary of notification letter requirements. Notify facilities as follows:

a. PAH/Associate Facility. The lead evaluation office will perform these tasks:

(1) Prepare the notification letter and send it to the facility to be evaluated no later than 50 calendar days before the evaluation.

(2) Provide a copy of the notification letter to the designated evaluation team leader or principal evaluator, the PI, and the AE.

b. Changes After Notification Letter Is Sent. As appropriate, notify the facility, responsible PAH or associate facility, requesting MIDO or CMO, AIR–200, and the team leader or principal evaluator of any changes to the evaluation schedule or team composition after the notification letter has been sent.

8100.7C 10/12/2005

Page 20 Par 37

37. MODIFICATIONS TO SCHEDULED EVALUATIONS. Every effort will be made to maintain established evaluation schedules. However, modifications to the evaluation schedule should be considered under special circumstances. The ACO, MIO, MIDO, and CMO managers will jointly reschedule any affected evaluation in coordination with the PI, AE, and the team leader or principal evaluator, and notify AIR–200 of the change in schedule. Special circumstances that may warrant modifications to the evaluation schedule include—

a. Risk to evaluators’ safety,

b. Change in a facility’s production or delegation status from active to inactive,

c. Involvement of the FAA in a facility’s labor-management dispute,

d. Reduction in the effectiveness of the evaluation, and

e. A nonscheduled ACSEP evaluation that requires scheduled resources (see paragraph 38).

38. NONSCHEDULED ACSEP EVALUATIONS. The ACO, MIO, MIDO, and CMO managers may also conduct nonscheduled ACSEP evaluations when situations warrant, as determined by directorate offices or Washington headquarters. Nonscheduled ACSEP evaluations will be planned, conducted, and reported in accordance with this order to the greatest extent practicable. Appropriate emphasis on planning the evaluation should be provided despite the reduced time that may be available between the decision to conduct the nonscheduled ACSEP evaluation and the actual conduct of the evaluation. Situations that may warrant a nonscheduled ACSEP evaluation include the following:

a. Accidents and incidents,

b. Deliberate violations,

c. Repetitive service difficulty reports,

d. Excessive owner/operator complaints,

e. PAH’s or associate facility’s refusal/failure to take appropriate corrective action,

f. PAH’s or associate facility’s inability to control suppliers,

g. Renewal of a PAH’s or associate facility’s production activity after a prolonged period of inactivity, and

h. Any other situation as deemed necessary in the interest of safety.

39.–41. RESERVED.

5/29/2008 8100.7C CHG 2

Par 42 Page 21

CHAPTER 4. ACSEP EVALUATION PROCEDURES

SECTION 1. ACSEP EVALUATION PREPARATIONS

SECTION 1. ACSEP EVALUATION PREPARATIONS

42. LEAD EVALUATION OFFICE. Perform the following evaluation preparations, as a minimum:

a. Notify, in writing, the selected evaluation team leader and team members, or the principal evaluator, at least 60 calendar days before each directorate evaluation. The notification does not need to be documented.

b. Ensure logistical support for an evaluation within the geographical area.

43. ACO, MIO, MIDO, and CMO MANAGERS. Notify in writing all evaluators within the directorate selected for AIR–200-led evaluations and evaluations in support of other directorates. Send notification at least 60 calendar days before each evaluation. Send a notification to the lead evaluation office and AIR–200. The notification does not need to be documented.

44. EVALUATION TEAM LEADER OR PRINCIPAL EVALUATOR. Coordinate evaluation preparation. The team leader provides orientation to team members, and assigns system elements to team members. These actions, as appropriate, require coordination with the PI, AE, and the facility to be evaluated. The team leader or principal evaluator will perform the following, as appropriate:

a. Upon receipt of a copy of the notification letter, contact the lead evaluation office to identify the responsible PI and AE and obtain from the PI and AE such items as the following:

(1) Applicable FAA-approved procedures, including engineering and quality manuals, procedures manuals, and handbooks, when practical. Obtain documentation in electronic format, if available, to simplify copying and distribution to team members. If applicable data are available only electronically, work with the PI or AE to identify relevant documents and to obtain printed copies of only those pages necessary to support the ACSEP evaluation.

(2) Current facility data available in the CMIS.

(3) Known or suspected problem areas, including any areas the PI and AE would like special emphasis on during the evaluation, such as requests to conduct a product audit in accordance with Order 8120.2.

(4) Current self-disclosure items reported under FAA Order 2150.3, Compliance and Enforcement Program, appendix 1, Compliance/Enforcement Bulletin No. 92–2, Reporting and Correction Policy and Implementing Guidance for Holders of Production Approvals, that are in the process of corrective action.

(5) Agreements made between the cognizant ACO, MIO, MIDO, or CMO and the facility to be evaluated.

(6) Facility access information, including badges and security clearances.

(7) Lodging information.

8100.7C 10/12/2005

Page 22 Par 44

(8) Any other items necessary to prepare for the evaluation.

b. Prepare a written evaluation plan for conducting the evaluation. The evaluation plan includes the following items:

(1) Name and address of the facility to be evaluated.

(2) Dates of the evaluation.

(3) Names of the team leader and members (when more than one evaluator is selected).

(4) Evaluation objectives. List the reason for the ACSEP evaluation and what information is expected to be obtained during the evaluation (for example, establish facility compliance with the procedures established to meet the applicable requirements of 14 CFR or establish cause of repetitive service difficulty reports).

(5) Type(s) of approval.

(6) Type certificate (TC) or supplemental type certificate (STC) number, as applicable.

(7) Current product line.

(8) Number of employees associated directly with the production approval activity.

(9) List of top-level FAA-approved procedures (for example, quality manual index of procedures, procedures manual, PMA approval letter, and TC data sheets).

(10) FAA/facility agreements in effect; for example, agreement on frequency of submittal of minor design changes.

(11) Plant layout.

(12) Organizational chart.

(13) Major processes.

(14) Unusual features of the product, manufacturing and inspection methods, or design approval system.

(15) Self-disclosure items under Order 2150.3, appendix 1, Compliance/Enforcement Bulletin No. 92–2.

(16) Special emphasis items recommended by the PI and AE.

(17) System element, to include product audit, assignments (when more than one evaluator is selected).

(18) Access information, including facility point of contact.

5/29/2008 8100.7C CHG 2

Par 44 Page 23

(19) Lodging information.

(20) Equipment required (for example, notebook computer, safety shoes, and coveralls).

c. Coordinate assignments, requirements, and arrangements with team members as far in advance of the evaluation as possible, but no later than 30 calendar days before the evaluation. Notify team members immediately of changes in schedule, assignments, requirements, and arrangements. Provide copies of all relevant facility documents to team members, when feasible.

NOTE: Information contained in the previous year’s annual ACSEP report may be used to assist the team leader in focusing resources in the event of time constraints.

d. Forward an FAA certificate of nondisclosure (see appendix 2) to any outside support service personnel assigned no later than 35 calendar days before the evaluation. Obtain signed statements no later than 25 calendar days before the evaluation and forward them to the facility via the PI.

e. Notify the lead evaluation office immediately of changes in team numbers or composition.

f. Coordinate with the certificate management PI or AE, or geographic PI, as appropriate, to resolve specific planning problems relating to the facility to be evaluated.

g. Arrange, as appropriate, for the availability of a notebook computer and portable printer for the duration of the evaluation, and for the accomplishment of postevaluation activities. Use of a notebook computer during the evaluation will allow for quick access and search of ACSEP documentation and for preparation of high-quality documents for presentation during the postevaluation conference.

45. EVALUATION TEAM MEMBER. Perform these tasks:

a. Upon notification by the team leader, confirm availability for the evaluation, system elements assigned, and travel arrangements.

NOTE: Notify the team leader immediately if you become unavailable for the evaluation.

b. Before the evaluation, review all material provided by the team leader, the PI, or the AE appropriate to the assigned system elements. When possible, make a preliminary selection of the procedures you plan to evaluate.

46.–51. RESERVED.

8100.7C 10/12/2005

Page 24 Par 52

SECTION 2. CONDUCT OF THE EVALUATION

SECTION 2. CONDUCT OF THE EVALUATION

52. TEAM LEADER OR PRINCIPAL EVALUATOR COORDINATION WITH FACILITY REPRESENTATIVE. The team leader or principal evaluator will coordinate with the designated representative of the facility to be evaluated to ensure administrative arrangements for items such as team access, escorts, meeting rooms, and safety and security requirements are complete.

53. PREEVALUATION TEAM MEETING. The team leader and all team members meet in advance of starting the evaluation, usually at the facility to be evaluated. They review the following evaluation elements, as appropriate, for proper coordination and understanding:

a. Current quality system or design approval system, and corrective action history of the facility to be evaluated in the selected areas.

b. Team functional assignments.

c. Evaluation plan.

d. Evaluation objectives.

e. Working relationship of the facility to be evaluated with the FAA.

f. Organizational structure of the facility to be evaluated.

g. Approved quality system documents, including any quality manual or quality data submitted by APIS or PMA holders to describe their inspection systems.

h. Approved design approval system documents, including any procedures manual or handbook.

i. Agreements made between the cognizant ACO, MIO, MIDO, or CMO and the facility to be evaluated.

54. PREEVALUATION CONFERENCE. Soon after arrival at the facility to be evaluated, the evaluation team leader or principal evaluator conducts a preevaluation conference with appropriate senior management, cognizant supervisory personnel, and other appropriate personnel of the facility who will be associated with the evaluation, including escorts. The team leader or principal evaluator must perform the following tasks, as appropriate:

a. Introduce team members and support service personnel.

b. Give a brief overview of ACSEP, highlighting the cooperative intention of the evaluation.

c. Provide the evaluation’s scope and objectives.

d. Review details of the evaluation agenda, including the standardized evaluation criteria and procedures to be used.

e. Review administrative arrangements for the postevaluation conference.

1/30/2009 8100.7C CHG 3

Par 54 Page 25

f. Discuss FAA Form 8100–7 sent with the notification letter to the facility being evaluated. Explain that this form is designed to obtain senior management assessment of the conduct of the ACSEP evaluation and is used by the FAA for continuous quality improvement of the certificate management program. Encourage senior management to complete the form and send it to the address on the form within 30 calendar days of the postevaluation conference.

g. Allow time for a question-and-answer session.

55. EVALUATION OF SYSTEM ELEMENTS. The ACSEP evaluation team evaluates up to six system elements and conducts at least one product audit at PAHs and associate facilities. Each system element addresses a specific activity or function that may affect the maintenance of FAA-approved design or quality data. Each system element is defined in appendix 5. The ACSEP evaluation team will perform the following tasks, as appropriate:

a. Review FAA-approved quality systems manuals or procedures manuals/handbooks to determine if current data ensure regulatory requirements are met, if conforming products and parts are manufactured, and if design approval systems are maintained and controlled.

b. Review design system, design approval system, and quality system data to determine if current data are FAA-approved.

c. Review other facility procedures (related to the production approval facility) that are not part of the facility’s FAA-approved data to determine if the current procedures impact any of the system elements.

d. Review PAH supplier records by selecting a random sample of PAH supplier audit reports. (Refer to appendix 5, section 6, paragraph 1a.)

(1) The reports may consist of onsite evaluations, mail-in surveys, third-party evaluations, or a combination of all three. The reports must be reviewed for compliance with the PAHs’ quality control system requirements. This may include, but is not limited to, the following conditions:

(a) Adherence to scheduled frequency of supplier control audits.

(b) Appropriate documentation of audits. This includes a signature by an appropriate authority, and attachment of required certifications and test documents.

(c) Determination of whether noncompliances provide evidence of root cause, corrective action, followup, and closure.

(d) If a history of similar noncompliances is evident, determination of whether the PAH is appropriately conducting root cause analysis and applying corrective action.

(2) The ACSEP report’s Special Emphasis page will be used to record the following information under the section, “Note to MIO Manager and Cognizant Principal Inspector”:

8100.7C CHG 3 1/30/2009

Page 26 Par 55

(a) Total number of audit reports reviewed.

(b) Identification of suppliers reviewed.

(c) Total number of noncompliances documented for all supplier reports reviewed.

NOTE 1: A later revision to CMIS will allow the data from the supplier audit report to be applied to FAA Form 8100–4, ACSEP Survey Sheet for Production Approval Holders.

NOTE 2: The results will be used for two purposes: (1) to identify areas that may require more focused attention during evaluation of the supplier control system element; and (2) as input into the following year’s risk-based resource targeting assessment of the PAH.

(3) Any noncompliance noted during the review of PAH supplier audit reports will be recorded under supplier control system element criteria number 602. Noncompliance will also be documented in accordance with paragraph 56 of the order.

NOTE: Paragraph 55d, and appendix 5, section 6, paragraph 1a, apply only to PAH facilities that use suppliers in the process of manufacturing FAAapproved products. Review of supplier records should be started early in the evaluation process to allow for additional time in case issues are noted.

e. Evaluate compliance to facility procedures and quality requirements. Prioritize evaluation according to any special concerns raised by the PI or AE. Use the standardized evaluation criteria in appendix 5 to determine the depth of the evaluation in the subject area. Evaluate, as necessary, a combination of document and product review to determine if the system element meets applicable requirements.

NOTE: The standardized evaluation criteria are a list of questions and related statements of condition in appendix 5 used primarily to plan and document the results of the evaluation of each system element in a standardized manner. The criteria are designed to cross all the functional areas within a facility’s organization that have the greatest potential to impact the integrity of the FAA-approved design and product quality. All responses to the questions are direct inputs to the database from which trend analysis is accomplished. Each evaluator should be knowledgeable of all the criteria applicable to the system element assigned to be evaluated and should strive to evaluate as many of the procedures, requirements, and products related to the criteria as time allows.

f. Select at least one team member to conduct at least one product audit at a PAH or associate facility of a manufactured product (for example, characteristic dimensioning, processing attributes, and physical examination) to determine compliance with current system procedures and quality requirements. Refer to Order 8120.2 for product audit areas, criteria, and procedures for recording audit results.

1/30/2009 8100.7C CHG 3

Par 55 Page 27

NOTE 1: Aviation safety engineers (ASE) who are currently active team members/leaders will gain experience conducting product audits by assisting an aviation safety inspector (ASI) who is part of the team and is conducting the required product audit and/or during certificate management functions, which includes conducting a product audit.

NOTE 2: New ASEs will gain experience in performing product audits by assisting ASIs during scheduled ACSEP evaluations as part of their evaluator-in-training requirements and/or assisting during certificate management functions, which includes conducting a product audit.

g. On the basis of facility procedures or quality requirements, identify and document additional standardized evaluation criteria questions and statement-of-condition practices and principles not contained in appendix 5 that were required to document what was evaluated. Write or type additional criteria and statement-of-condition practices and principles, and include the appropriate reference to the facility procedures or quality requirements and the evaluator’s recommendation of the system element to which the criteria and statement of condition apply. Team members must present new criteria and statement-of-condition practices and principles to the team leader as soon as they are completed.

h. Detect and report nonconformances and areas that may require additional evaluation by the PI or AE.

56. RECORDING NONCOMPLIANCES. Evaluators will record all noncompliances on FAA Form 8100–6, Noncompliance Record, or electronic equivalent, according to the guidelines in Order 8120.2.

NOTE: Record as a certification-related noncompliance any condition that questions the certification basis. Address the noncompliance on the Executive Summary (refer to paragraphs 57b (2) (c) and 62b, and appendix 6) and as a special emphasis item in the evaluation report (refer to paragraphs 57b(2)(d) and 62c, and appendix 7).

57. EVALUATION MEETINGS.

a. Daily Meeting. The team leader or principal evaluator holds the following daily meetings, as appropriate:

(1) Meeting with Evaluation Team Members. The team leader will review and discuss the following with team members:

(a) Status of the evaluation.

(b) Problems encountered.

(c) Plan of the next day’s evaluation.

(d) All Form(s) 8100–6, or electronic equivalent, prepared during the day to ensure correctness, adequacy, and completeness.

8100.7C CHG 3 1/30/2009

Page 28 Par 57

(2) Meeting/Communication With PI and AE. The team leader or principal evaluator ensures the certificate management PI and AE, and the geographic PI, as applicable, are informed of all discussions concerning the status of the evaluation. This meeting should occur daily when the PI and AE are part of the evaluation team. Otherwise, coordinate with the PI and AE to establish the method and frequency at which these discussions should occur.

(3) Meeting With the Evaluated Facility’s Designated Representative. The team leader or principal evaluator holds a brief meeting daily with the evaluated facility’s designated representative to discuss the progress of the evaluation, including problems encountered, the status of actions requested by the team, schedule changes, and the coordination of further evaluation activities.

b. Final Critique Meeting/Evaluation Wrap-Up. At the conclusion of the evaluation, the team leader holds a final critique meeting. The principal evaluator allows time to finalize the details of the evaluation. The team leader and members or the principal evaluator do the following, as appropriate:

(1) Team Members or Principal Evaluator.

(a) Complete all required Form(s) 8100–6, or electronic equivalent. When using an electronic equivalent, print to paper when all information has been entered. Team members discuss Form(s) 8100–6 with the team leader to determine if there are any possible violations of the applicable requirements of 14 CFR. The team leader must resolve any disagreement on noncompliance(s). The lead evaluation office, or requesting MIDO or CMO, as applicable, must determine the level of corrective action required (see paragraph 65).

(b) Ensure all true copies of objective evidence are attached to the appropriate Form(s) 8100–6, or electronic equivalent, appropriately referenced, and clearly identified in accordance with Order 2150.3.

(c) Complete Form 8100–4 or electronic equivalent in accordance with appendix 5. When using an electronic equivalent, print to paper when all information has been entered. Prepare original forms as follows:

1 PAH or Associate Facility. Prepare one original Form 8100–4.

2 Facility With Multiple Production Approvals. Prepare one original Form 8100–4. Base the survey responses on the criteria for the highest-level quality requirement; for the purposes of ACSEP, the quality levels, from highest to lowest, are PC, TSO authorization, APIS, and PMA. For example, if a facility has a PMA and a TSO authorization, prepare one Form 8100–4 based on the TSO authorization criteria.

(2) Team Leader or Principal Evaluator.

(a) Resolve team disagreements on specific noncompliances.

(b) Discuss all noncompliances with the certificate management PI or AE, delegated facility AE, and geographic PI, as applicable.

1/30/2009 8100.7C CHG 3

Par 57 Page 29

(c) Prepare the ACSEP Evaluation Executive Summary (see appendix 6). Prepare original forms as follows:

1 PAH or Associate Facility. Prepare one original summary.

2 Facility With Multiple Production Approvals. Prepare one original summary. For example, if a facility has a PMA and a TSO authorization, prepare one original summary.

(d) Identify and record specific problems or concerns that the ACSEP evaluation team believes require further action and that should be brought to the attention of the ACO, MIO, MIDO, or CMO managers, the geographic PI, the AE, and the flight standards principal maintenance inspector (as appropriate). Use the instructions in appendix 7 to record these special emphasis items. Prepare original documents as follows:

1 PAH or Associate Facility. Prepare one original document.

2 Facility With Multiple Production Approvals. Prepare only one original document. For example, if a facility has a PMA and a TSO authorization, prepare one original document.

(e) Discuss with team members, as appropriate, and record any lessons learned during the ACSEP evaluation that may improve ACSEP policy or evaluation techniques. Use the instructions in appendix 8. Prepare only one original document and include copies with each report.

(f) Verify that signed original Form(s) 8100–6 have been prepared for inclusion, as applicable, in each ACSEP evaluation report to be sent to the responsible certificate management MIDO, CMO, or ACO having delegation oversight. See paragraph 62f. Each report to be sent must include all applicable Form(s) 8100–6. When a signed original Form 8100–6 is applicable to two or more reports, do the following:

1 Reproduce the signed original Form(s) 8100–6 as required for inclusion in the applicable ACSEP evaluation report(s) to be sent to the responsible certificate management MIDO or CMO having oversight.

2 Identify all true copies of the signed form in accordance with Order 2150.3.

(g) Provide a copy of the completed final draft Form(s) 8100–6 to the certificate management PI or AE, and the geographic PI, as applicable, when they are present.

(h) Verify the required number of true copies of objective evidence have been prepared for inclusion, as applicable, in each ACSEP evaluation report to be sent to the responsible certificate management MIDO or CMO having oversight.

(i) Provide all true copies of objective evidence to the certificate management PI or AE, when present. When the PI or AE is not present, forward the copies in accordance with the applicable instructions in paragraph 64a. If the objective evidence will be necessary as a reference during preparation of the evaluation report, make a separate copy and identify each page as “For Reference Only.”

8100.7C CHG 3 1/30/2009

Page 30 Par 57

(3) Certificate Management PI or AE, or Geographic PI (When Present). As appropriate, consider providing a copy of the completed final draft Form(s) 8100–6 to the facility’s management. Clearly mark each copy as “DRAFT” before release.

58. POSTEVALUATION CONFERENCE. The team leader or principal evaluator must conduct a postevaluation conference with appropriate senior management and cognizant supervisory personnel of the evaluated facility. The team leader or principal evaluator must do the following, as appropriate:

a. Introduce FAA personnel not previously introduced at the preevaluation conference.

b. Give a brief presentation of the overall results of the evaluation, using each completed ACSEP Evaluation Executive Summary as a reference:

(1) Provide a copy of each completed ACSEP Evaluation Executive Summary to the evaluated facility’s designated representative.

(2) Summarize all noncompliances. Mention only noncompliances previously discussed with the certificate management PI and AE, the geographic PI, as applicable, and facility personnel.

c. Explain the purpose and use of the ACSEP database.

d. Explain corrective action and followup procedures.

NOTE: Emphasize that the PI or AE may conduct additional investigations into noncompliances reported in the ACSEP evaluation report. The results of these investigations may be included with the letter requesting corrective action for the ACSEP evaluation noncompliances.

e. Remind senior management about FAA Form 8100–7 and encourage them to complete the form and send it to the address on the form within 30 calendar days of the postevaluation conference.

f. Request final comments. Clarify any misunderstandings or disagreements before departure.

g. Adjourn the ACSEP evaluation.

59.–61. RESERVED.

1/30/2009 8100.7C CHG 3

Par 62 Page 31

SECTION 3. POSTEVALUATION ACTIVITIES

SECTION 3. POSTEVALUATION ACTIVITIES

62. PREPARING THE ACSEP EVALUATION REPORT. The team leader or principal evaluator must prepare the ACSEP evaluation report. When a facility has one or more production approvals, prepare one original evaluation report. Format and compile each original evaluation report in the following order:

NOTE: Ensure the evaluation report identifies only noncompliances presented at the postevaluation conference.

a. FAA Form 8100–3, ACSEP Evaluation Report, or printed copy of electronic equivalent (appendix 9). Each form or printed copy must be an original and signed. Prepare an original form or printed copy for each PAH affected.

b. ACSEP Executive Summary or printed copy of electronic equivalent (appendix 6). Each summary must be an original and signed. Prepare an original summary or printed copy for each PAH affected.

c. ACSEP Evaluation Special Emphasis Items or printed copy of electronic equivalent (appendix 7). Prepare an original list of special emphasis items or printed copy for each PAH affected.

d. ACSEP Evaluation Lessons Learned or printed copy of electronic equivalent (appendix 8). Prepare an original list of lessons learned or printed copy for each evaluation.

e. Form 8100–4 or printed copy of electronic equivalent (appendix 5, part B). Prepare an original form or printed copy for each PAH facility affected.

f. Form 8100–6 or printed copy of electronic equivalent. Include signed originals, or true copies of the signed form when identical signed original Form(s) 8100–6 are required for two or more reports. See paragraph 57b(2)(f). Each report must include all applicable Form(s) 8100–6 and any objective evidence. Each copy of the objective evidence must be a true copy of the original documents, identified as indicated in paragraph 57b(1)(b). Include true copies for each PAH affected.

NOTE: Do not include reproductions of true copies of objective evidence in an original evaluation report. Objective evidence must be a true copy signed and dated in accordance with Order 2150.3.

63. QUALITY REVIEW OF THE ACSEP EVALUATION REPORT. The ACSEP Evaluation Report contains the data that forms the basis of corrective action requests (see paragraph 65) and the ACSEP national database described in chapter 5 of this order. To this end, the evaluation report must be accurate and complete. Directorate managers (or delegated individuals) must establish a review process within their directorates that ensures accuracy and completion of the evaluation report before distribution.

8100.7C CHG 3 1/30/2009

Page 32 Par 64

64. SENDING THE ACSEP EVALUATION REPORT. The team leader or principal evaluator and the responsible ACO and MIO managers (or designated individuals) will process the evaluation report as follows (see appendix 10):

a. Team Leader or Principal Evaluator.

(1) PAH/Associate Facility.

(a) Send, or transmit electronically, an original evaluation report to the review point within 15 working days of the postevaluation conference. The review point must return the report to the team leader or principal evaluator for correction and/or continued processing within 5 working days of receipt.

(b) Send, or transmit electronically, the original evaluation report to the responsible certificate management MIO manager within 5 working days of receipt of review point comments. Do not send copies of objective evidence to the MIO manager. Send all true copies of any objective evidence to the certificate management PI.

(c) Send, or transmit electronically, at the same time as the original report, one copy of the evaluation report to the cognizant ACO manager and to AIR–200. The copy for the ACO manager may be tailored to the requirements of the ACO manager but will always include copies of any objective evidence that the ACO manager may require to investigate identified special emphasis items. Do not send copies of objective evidence to AIR–200.

(d) Send, or transmit electronically, at the same time as the original report, one copy of the evaluation report to the immediate supervisor of any evaluators-in-training assigned to the team.

b. Certificate Management MIO Manager.

(1) Send, or transmit electronically, the original evaluation report to the certificate management PI within 3 working days of receipt of the report from the ACSEP team leader.

(2) Include any additional evaluation documents that the team leader provides.

c. Certificate Management ACO Manager.

(1) Send, or transmit electronically, the evaluation report copy to the AE within 3 working days of receipt of the report from the ACSEP team leader.

(2) Include all copies of any objective evidence received. When transmitting the report electronically, send the true copies of the objective evidence under separate cover.

NOTE: ACO investigations of special emphasis items identified during the conduct of an ACSEP evaluation should be coordinated with the responsible MIDO or CMO.

1/30/2009 8100.7C CHG 3

Par 65 Page 33

65. REQUESTING CORRECTIVE ACTION. The PI must request corrective action in accordance with Order 8120.2.

66.–71. RESERVED.

8100.7C CHG 3 1/30/2009

Page 34 Par 72

CHAPTER 5. ACSEP AND CMIS

72. PURPOSE. CMIS will provide a capability to detect shifts in performance and statistically significant trends for the industry as a whole and for different segments of the industry. It also will identify trends emerging in the performance of ACSEP evaluations.

CHAPTER 5. ACSEP AND CMIS

73. FILES. CMIS will contain selected information from all ACSEP evaluations conducted. It will contain selected facility information, records of noncompliance for each ACSEP evaluation conducted, records of each Form 8100–4 and 8100–6 survey, records of lessons learned, and records of customer feedback reports.

74. DATABASE MANAGEMENT. AIR–220 will monitor CMIS and will do the following, as appropriate:

a. Review the database as follows:

(1) Examine new entries.

(2) Note shifting levels of performance in different segments of the industry, including any statistically significant differences in the system elements when compared at all PAHs and associate facilities.

(3) Highlight potential trends emerging in particular aspects of the system elements.

(4) Analyze trends emerging in particular aspects of the system elements.

(5) Highlight trends emerging in the performance of ACSEP evaluations.

b. Provide selected data and reports.

NOTE: All report recipients will use the information only internally and will not issue any reports outside of AIR. Refer to paragraph 10 of this order.

c. Obtain, as required, outside support services to augment its resources with qualified and creditable experts and specialists to support database management and system analyses in accordance with budgetary directives and in coordination with AIR–500. Sample contract clauses relating to obtaining support services are contained in appendix 2 to this order.

NOTE: AIR–220 will complete all necessary FAA administrative measures before assignment of support service personnel to database management and system analyses. These measures include ensuring personnel have signed a certificate of nondisclosure for confidentiality of information (see appendix 2).

1/30/2009 8100.7C CHG 3

Par 75 Page 35 (and 36)

75. USE OF THE DATABASE. Directorates may use CMIS to obtain reports on noncompliances, frequently used 14 CFR references, and industry compliance. They may use the database to detect shifts in performance and statistically significant trends for different segments of the industry. Directorates also may use the database to assist in scheduling.

76.–81. RESERVED.

Page 1 (and 2)

APPENDIX 1. ACRONYMS

APPENDIX 1. ACRONYMS

1. Applicability. The acronyms listed apply to this entire order.

14 CFR Title 14, Code of Federal Regulations AC Advisory Circular AC Form Aeronautical Center Form ACO Aircraft Certification Office ACSEP Aircraft Certification Systems Evaluation Program AD Airworthiness Directive AE assigned engineer AFM airplane flight manual AFMS airplane flight manual supplement AIR Aircraft Certification Service AIR–100 Aircraft Engineering Division AIR–200 Production and Airworthiness Division AIR–220 Airworthiness Certification Branch AIR–500 Planning and Program Management Division APIS Approved Production Inspection System ASI Aviation Safety Inspector CMO certificate management office CMIS Certificate Management Information System FAA Federal Aviation Administration FSDO flight standards district office MIDO manufacturing inspection district office MIO manufacturing inspection office MRB Materials Review Board NDI nondestructive inspection PAH production approval holder PC production certificate PI principal inspector PMA parts manufacturer approval STC supplemental type certificate TC type certificate TSO technical standard order

APPENDIX 2. PREPARATION OF CLAUSES FOR CONTRACTS FOR SUPPORT SERVICES

APPENDIX 2. PREPARATION OF CLAUSES FOR CONTRACTS FOR SUPPORT SERVICES

1. PURPOSE. This appendix provides sample contract clauses and a sample certificate of nondisclosure for use in contracts for obtaining services to support ACSEP evaluations, database management, and system analyses.

2. SAMPLE CLAUSES AND ATTACHMENT. The following sample clauses provide the minimum requirements to be included in a contract for support services. Figure 1 shows a sample attachment to the Confidentiality of Information clause requiring support service personnel to agree to its terms and conditions.

a. The following clause is applicable to all contractors:

H.1 Confidentiality of Information.

a. To the extent that the work under this contract requires that the contractor be given access to confidential or proprietary business or technical information belonging to the Government or other companies, designees, contractors, or competitors, or to the extent that in performing the work under this contract, the contractor gains access to Government data through any means, then the contractor must, after receipt thereof, treat such information as confidential and agree not to appropriate such information to its own use or to disclose such information to third parties unless specifically authorized by the contracting officer in writing; however, the foregoing obligations must not apply to the following:

(1) Information that, at the time of receipt by the contractor, is in public domain.

(2) Information that is published after receipt thereof by the contractor or otherwise becomes part of the public domain through no fault of the contractor.

(3) Information that the contractor has in its possession at the time of receipt thereof and was not acquired directly or indirectly from the Government or other companies.

(4) Information that the contractor can demonstrate was received by it from a third party who did not require the contractor to hold it in confidence.

b. The contractor must execute the certificate set forth as attachment 1 for each employee who will participate as an evaluator under this contract. The certificate must be presented by the contractor’s employees or forwarded by the FAA to various companies who may be evaluated under the contract.

APPENDIX 2. PREPARATION OF CLAUSES FOR CONTRACTS FOR SUPPORT SERVICES

FIGURE 1. SAMPLE CERTIFICATE OF NONDISCLOSURE

FIGURE 1. SAMPLE CERTIFICATE OF NONDISCLOSURE

Attachment 1. Certificate of Nondisclosure

The undersigned hereby agrees to the terms and conditions set forth in the clause below:

H.1 Confidentiality of Information.

a. To the extent that the work under this contract requires that the contractor be given access to confidential or proprietary business or technical information belonging to the Government or other companies, designees, contractors, or competitors, or to the extent that in performing the work under this contract, the contractor gains access to Government data through any means, then the contractor must, after receipt thereof, treat such information as confidential and agree not to appropriate such information to its own use or to disclose such information to third parties unless specifically authorized by the contracting officer in writing; however, the foregoing obligations must not apply to the following:

(1) Information that, at the time of receipt by the contractor, is in public domain.

(2) Information that is published after receipt thereof by the contractor or otherwise becomes part of the public domain through no fault of the contractor.

(3) Information that the contractor has in its possession at the time of receipt thereof and was not acquired directly or indirectly from the Government or other companies.

(4) Information that the contractor can demonstrate was received by it from a third party who did not require the contractor to hold it in confidence.

b. The contractor must execute the certificate set forth as attachment 1 for each employee who will participate as an evaluator under this contract. The certificate must be presented by the contractor’s employees or forwarded by the FAA to various companies who may be evaluated under the contract.

… … Authorized Contractor Agent Date Contractor Employee Date

Page 3 (and 4)

APPENDIX 2. PREPARATION OF CLAUSES FOR CONTRACTS FOR SUPPORT SERVICES

APPENDIX 2. PREPARATION OF CLAUSES FOR CONTRACTS FOR SUPPORT SERVICES

b. The following clause is applicable to support service personnel who will support ACSEP evaluations and should be used in conjunction with clause H.1:

H.2 Relationships. The contractor must provide support to the Government by completing work assigned under this contract. Support must be provided in the following areas: auditing of quality and engineering functions; collection, evaluation, and processing of data; and written documentation of incidents not in compliance with ACSEP evaluation criteria. The contractor must not provide technical direction under the contract. The contractor must abide by any limitations of access and entry to proprietary or sensitive processes or systems that the Government may stipulate. Although the effort under this contract may include the collection and processing of data, as well as the formulation of noncompliances and recommendations, the final disposition of all information must remain the sole province of the Government.

c. The following clause is applicable to support service personnel who will support database management or system analysis and should be used in conjunction with clause H.1:

H.2 Relationships. The contractor must provide support to the Government by completing work assigned under this contract. Support must be provided in the following areas: input, analysis, and trending of data; and compilation of analytical reports. The final disposition of all information must remain the sole province of the Government.

Continue reading ↓ 120 of 296 passages shown