Radar Vectors
FAA Order Cancelled Issued Aug 28, 2019 AJV-P 20 pages Copy saved Nov 18, 2026

Order JO 7110.126A Consolidated Wake Turbulence (CWT) Separation Standards

This order provides procedural guidance to FAA Order JO 7110.65, Air Traffic Control, related to the use of Consolidated Wake Turbulence procedures and separation minima

This document is cancelled. Cancelled by JO 7110.126B. Check the official source before relying on it.

Official source ↗ Open PDF

ORDER JO 7110.126A Air Traffic Organization Policy

Effective Date: September 28, 2019

SUBJ: Consolidated Wake Turbulence (CWT) Separation Standards

1. Purpose of This Order. This order provides procedural guidance to F AA Order JO 7110.65, Air Traffic Control, related to the use of Consolidated Wake Turbulence procedures and separation minima.

2. Audience. This order applies to all Air Traffic Organization (ATO) personnel authorized to use this order and anyone involved in the implementation and monitoring of Consolidated Wake Turbulence separation standards.

3. Where Can I Find This Order? This change is available on the FAA Website at http://faa.gov/air_traffic/publications and https://employees.faa.gov/tools_resources/orders_notices/.

4. What This Order Cancels. FAA Order JO 7110.126, Consolidated Wake Turbulence Radar Separation Standards, dated July 17, 2018, and all changes to it are cancelled.

5. Explanation of Changes.

a. This change incorporates select wake turbulence separation minima and associated phraseology from FAA Order JO 7110.65 and FAA Order JO 7110.123. RECAT Phase II separation minima between certain aircraft categories are leveraged to remove wake turbulence separation requirements wherein any Heavy aircraft follows a Lower Heavy aircraft and an Upper Small aircraft follows an Upper Large (including the B757) aircraft. These changes, and others such as replacing aircraft weight classes with aircraft wake turbulence categories in some instances, are captured in the following paragraphs: 2-1-20b., 2-4-14b. and c., 2-4-21d. and e., 3- 3-5b.1., 3-7-3a. and b., 3-9-6c. through n., 3-9-7a. through b.1., 3-9-8b.3., 3-9-9c., 3-10-3b., 3-10- 4c. and d., 3-10-10 NOTE-1, 3-11-1d., 4-8-11b.2., 6-1-4, 6-1-5, 6-7-5, and 7-2-1.

b. Editorial and format changes were made where necessary. Revision bars were not used to indicate any of the listed changes.

6. Requirements.

a. Facilities must receive a Letter of Authorization from the Director, Air Traffic Procedures, AJV–8, prior to the implementation of CWT procedures.

b. At facilities authorized to use this order for air traffic control services, the applicable provisions of FAA Order JO 7110.65, Air Traffic Control, are superseded by the corresponding provisions contained in this order.

c. Personnel providing air traffic control service must receive training on CWT procedures prior to implementation, or prior to assuming an operational position if the training occurs post implementation.

d. Terminal Automation Systems must have the CWT functions activated and all operational personnel appropriately trained prior to the use of this order.

Distribution: Electronic Initiated By: AJV-8 Mission Support, Terminal Procedures

… …

e. Tower facilities must be equipped with a Flight Data Input/Output (FDIO), Electronic Flight Strip Transfer System (EFSTS), an equivalent electronic flight progress strip system, or develop manual procedures to indicate the wake category on flight progress strips.

f. Facility documents must be updated, as appropriate, to reflect CWT procedures.

g. Facilities must submit a weekly report of any wake encounter reports and Mandatory Occurrence Reports (MOR) concerning wake turbulence for the first six months after implementation.

h. Air Traffic Procedures, AJV–8, must notify Safety and Technical Training, who will in turn notify Air Traffic Safety Oversight Services (AOV) of facilities authorized to use CWT procedures and separation minima.

7. Background. Over the past several years, knowledge about wake vortex behavior in the operational environment has increased due to multiple advances in measurement techniques, available automated surveillance data, and improved understanding of physical processes. The FAA has undertaken an effort to recategorize the existing fleet of aircraft and modify the associated wake turbulence separation minima. Prior to this effort, approach and departure wake turbulence separation minima were mostly based on Maximum Certificated Gross Takeoff Weight (MCGTOW). Updates in methodology make some wake turbulence separation standards in FAA Order JO 7110.65 result in greater than necessary separation distances. For example, in some instances, Heavy-behind-Heavy separation in FAA Order JO 7110.65 is four miles. This separation is appropriate for a B767 following a B747, but not necessary when the B747 is following the B767.

FAA Order JO 7110.659 (RECAT 1.5) classified aircraft according to certificated takeoff weight, landing speed, wingspan, and the aircraft’s ability to withstand a wake encounter. FAA Order JO 7110.123 (RECAT Phase II), Appendix A and Appendix B, described a pairwise separation matrix developed for the most common ICAO type identifier aircraft. Each aircraft was addressed as both a leader and a follower in each pair. The development of a pairwise separation matrix relied on wakebased data, rather than weight-based data. Separation reductions were achieved with a better understanding of wake behavior and with pairwise separation of aircraft. CWT used the most operationally advantageous separation standards from the four previous sets of standards while retaining the use of all time-based wake turbulence separation standards from FAA Order JO 7110.65. CWT is based on a nine category system that further refines the grouping of aircraft, provides throughput gains at many of today’s constrained airports, and is manageable for all airports throughout the NAS.

All five sets of wake turbulence separation standards have been reviewed by Safety and Technical Training (AJI) and accepted/approved for operational use by AOV. The RECAT Phase II methodology that went into developing FAA Order JO 7110.123 determined that there is no need for wake turbulence separation for any Heavy aircraft following Lower Heavy aircraft, nor for Upper Small aircraft following Upper Large aircraft, including B757s. The goal of this revision to CWT is to incorporate these reductions in wake turbulence separation standards into sections of Chapter 3 and Chapter 6 in an effort to capitalize on operational efficiencies while continuing to provide throughput gains at many of the airports throughout the NAS.

Natking Estevez Date Director (A), Air Traffic Procedures

Appendix A

Appendix A

Appendix A

Aircraft Wake Categories

Category A – A388. Category B – Pairwise Upper Heavy aircraft. Category C – Pairwise Lower Heavy aircraft Category D – Non-Pairwise Heavy aircraft.

Category E – B757 aircraft. Category F – Upper Large aircraft excluding B757 aircraft. Category G – Lower Large aircraft. Category H – Upper Small aircraft with a maximum takeoff weight of more than 15,400 pounds up to 41,000 pounds. Category I – Lower Small aircraft with a maximum takeoff weight of 15,400 pounds or less.

TBL A–1 Aircraft Types Categorized A

Super

B Upper Heavy

C Lower Heavy

D Non-Pairwise

Heavy

E

B757

F

Upper Large

G

Lower Large

H Upper

Small

I Lower

Small

A388 A332 A306 A124 DC85 B752 A318 C130 AT43 E170 ASTR BE10 A333 A30B A339 DC86 B753 A319 C30J AT72 E45X B190 BE20 A343 A310 A342 DC87 A320 CVLT CL60 E75L BE40 BE58 A345 B762 A3ST E3CF A321 DC93 CRJ1 E75S B350 BE99 A346 B763 A400 E3TF B712 DC95 CRJ2 F16 C560 C208 A359 B764 A50 E6 B721 DH8D CRJ7 F18H C56X C210 B742 C17 AN22 E767 B722 E190 CRJ9 F18S C680 C25A B744 DC10 B1 IL62 B732 GL5T CRJX F900 C750 C25B B748 K35R B2 IL76 B733 GLEX DC91 FA7X CL30 C402 B772 MD11 B52 IL86 B734 GLF5 DH8A GLF2 E120 C441 B773 B703 IL96 B735 GLF6 DH8B GLF3 F2TH C525 B77L B741 K35E B736 MD82 DH8C GLF4 FA50 C550 B77W B743 KE3 B737 MD83 E135 SB20 GALX P180 B788 B74D L101 B738 MD87 E145 SF34 H25B PAY2 B789 B74R MYA4 B739 MD88 LJ31 PA31 C5 B74S R135 MD90 LJ35 PC12 C5M B78X T144 LJ45 SR22 BLCF T160 LJ55 SW3 BSCA TU95 LJ60 C135 VMT SH36 C141 SW4 NOTE – 1. The A225 is treated as a NOWGT aircraft.

2. TBL A-1 lists the most common aircraft for all Wake Categories, and is not an all-inclusive list. However, aircraft automation databases list all aircraft that have been assigned an aircraft type designator. Entering the appropriate aircraft type designator will allow automation systems such as Standard Terminal Automation Replacement System (STARS) and Airport Surface Detection Equipment Model X (ASDE-X) to display the appropriate aircraft wake category for all assigned aircraft.

A1

Appendix B

Appendix B

Amend the following paragraphs in FAA Order JO 7110.65:

2–1–20. WAKE TURBULENCE CAUTIONARY ADVISORIES

Title through a.3., No Change

b. Issue cautionary information to any aircraft if in your opinion wake turbulence may have an adverse effect on it. When traffic is known to be a Category A aircraft, include the word Super in the description. When traffic is known to be a Category B, C, or D aircraft, include the word Heavy in the description.

2–1–20. WAKE TURBULENCE CAUTIONARY ADVISORIES

NOTE− Wake turbulence is generated when an aircraft produces lift. Because the location of wake turbulence is difficult to determine, the controller is not responsible for anticipating its existence or effect. Aircraft flying through a Super/Heavy aircraft’s flight path may have an increased chance of a wake encounter.

REFERENCE– AC 90-23, Aircraft Wake Turbulence. P/CG Term – Aircraft Wake Categories. P/CG Term –Wake Turbulence.

No further changes to paragraph

2–3–4. TERMINAL DATA ENTRIES

2–3–4. TERMINAL DATA ENTRIES

Title through TBL 2-3-3, block 2A, No Change

TBL 2-3-3

Block Information Recorded

3. Number of aircraft if more than one, aircraft wake category indicator, type of aircraft, and aircraft equipment suffix.

TBL 2–3–3, block 4 through TBL 2–3–4, block 2A, No Change

TBL 2-3-4

Block Information Recorded

3. Number of aircraft if more than one, aircraft wake category indicator, type of aircraft, and aircraft equipment suffix.

TBL 2–3–4, block 4 through TBL 2–3–5, block 2A, No Change

TBL 2-3-5

Block Information Recorded

3. Number of aircraft if more than one, aircraft wake category indicator, type of aircraft, and aircraft equipment suffix.

No further changes to paragraph

2–4–14. WORDS AND PHRASES

2–4–14. WORDS AND PHRASES

Title through a., No Change

b. The word Super must be used as part of the identification in all communications with or about Category A aircraft.

c. The word Heavy must be used as part of the identification in all communications with or about Category B, C, or D aircraft.

No further changes to paragraph

2–4–21. DESCRIPTION OF AIRCRAFT TYPES

2–4–21. DESCRIPTION OF AIRCRAFT TYPES

Except for Category A, B, C, and D aircraft, describe aircraft as follows when issuing traffic information:

a. through c.2. Example, No Change

d. When issuing traffic information to aircraft following a Category A aircraft, specify the word Super before the manufacturer's name and model.

EXAMPLE− “Super A-Three-Eighty” or “Super A-Three-Eighty-Eight.”

e. When issuing traffic information to aircraft following a Category B, C, or D aircraft, specify the word Heavy before the manufacturer's name and model.

EXAMPLE– “Heavy C-Seventeen.”

“Heavy Boeing Seven Forty-Seven.”

No further changes to paragraph

3–3–5. BRAKING ACTION ADVISORIES

3–3–5. BRAKING ACTION ADVISORIES

Title through b., No Change

1. Issue the latest braking a ction report for the runway in use to each arriving and departing aircraft early enough to be of benefit to the pilot. When possible, include reports from Category A, B, C, or D aircraft when the arriving or departing aircraft is a Category A, B, C, or D aircraft.

No further changes to paragraph

3–7–3. GROUND OPERATIONS

3–7–3. GROUND OPERATIONS

WAKE TURBULENCE APPLICATION

Avoid clearances which require:

a. Category A, B, C, or D aircraft to use greater than normal taxiing power.

b. Category H and I aircraft or helicopters to taxi in close proximity to taxiing or hover-taxi helicopters.

NOTE− Use caution when taxiing smaller aircraft/helicopters in the vicinity of larger aircraft/helicopters. Controllers may use the words “rotor wash”, “jet blast”, or “prop wash” when issuing cautionary advisories.

WAKE TURBULENCE APPLICATION

EXAMPLE− “Follow Boeing 757, Runway Three-Six Left, taxi via Alpha. C aution jet blast.”

or

When appropriate,

“Follow CH-53, Runway Two-One, taxi via Bravo. C aution rotor wash.”

REFERENCE− AC 90−23, Aircraft Wake Turbulence, Para 10 and Para 11.

No further changes to paragraph

3–9–6. SAME RUNWAY SEPARATION

3–9–6. SAME RUNWAY SEPARATION

Title through WAKE TURBULENCE APPLICATION, No Change

c. Do not issue clearances which imply or indicate approval of rolling takeoffs by Category A, B, C, or D aircraft except as provided in Paragraph 3−1−14, Ground Operations When Volcanic Ash is Present.

d. Do not issue clearances to a Category H or I aircraft to line up and wait on the same runway behind a departing Category A, B, C, or D aircraft to apply the necessary intervals.

REFERENCE−

C 90−23, Aircraft Wake Turbul A ence.

e. The minima in Paragraph 5−5−4, Minima, subparagraph g, TBL 5-5-1 may be applied in lieu of the time interval requirements in subparagraphs f, g, and h. When Paragraph 5−5−4 TBL 5-5-1 minima is applied, ensure that the appropriate radar separation exists at or prior to the time an aircraft becomes airborne.

REFERENCE− FAA Order JO 7210.3, Para 2–1–16, Authorization for Separation Services by Towers. FAA Order JO 7210.3, Para 10–5–3, Functional Use of Certified Tower Radar Displays.

NOTE− 1. The pilot may request additional separation, but should make this request before taxiing on the runway.

2. Takeoff clearance to the following aircraft should not be issued until the time interval has passed after the preceding aircraft begins takeoff roll.

f. Separate aircraft taking off from the same runway or a parallel runway separated by less than 2,500 feet (See FIG 3−9−4):

1. Category B, C, D, E, F, G, H, or I aircraft behind Category A aircraft – 3 minutes.

2. Category B, C, D, E, F, G, H, or I aircraft behind Category B or D aircraft – 2 minutes.

3. Category E, F, G, H, or I aircraft behind Category C aircraft – 2 minutes.

FIG 3–9–4 Same Runway Separation

g. Separate Category I aircraft behind Category E aircraft by 2 minutes when departing:

1. The same runway or a parallel runway separated by less than 700 feet. (See FIG 3–9–5 and FIG 3–9–6.)

FIG 3–9–5 Same Runway Separation

FIG 3–9–6 Parallel Runway Separated by Less than 700 Feet

2. A parallel runway separated by 700 feet or more, if flight paths will cross. (See FIG 3–9– 7.)

h. Separate aircraft departing from a parallel runway separated by 2,500 feet or more if projected flight paths will cross (See FIG 3−9−8):

1. Category B, C, D, E, F, G, H, or I aircraft behind Category A aircraft – 3 minutes.

2. Category B, C, D, E, F, G, H, or I aircraft behind Category B or D aircraft – 2 minutes.

3. Category E, F, G, H, or I aircraft behind Category C aircraft – 2 minutes.

FIG 3–9–8 Parallel Runways Separated by 2,500 Feet or More

i. Separate aircraft when operating on a runway with a displaced landing threshold if projected flight paths will cross, when either a departure follows an arrival or an arrival follows a departure by the following minima:

1. Category B, C, D, E, F, G, H, or I aircraft behind Category A aircraft – 3 minutes.

2. Category B, C, D, E, F, G, H, or I aircraft behind Category B or D aircraft - 2 minutes.

3. Category E, F, G, H, or I aircraft behind Category C aircraft - 2 minutes.

4. Category I aircraft behind Category E aircraft – 2 minutes.

j. Separate an aircraft behind another aircraft that has departed or made a low/missed approach when utilizing opposite direction takeoffs or landings on the same or parallel runways separated by less than 2,500 feet by the following minima:

1. Category B, C, D, E, F, G, H, or I aircraft behind Category A aircraft – 4 minutes.

2. Category B, C, D, E, F, G, H, or I aircraft behind Category B or D aircraft - 3 minutes.

3. Category E, F, G, H, or I aircraft behind Category C aircraft - 3 minutes.

FIG 3–9–7 Parallel Runway Separated by 700 Feet or More Projected Flight Paths Cross

k. Separate a Category I aircraft behind a Category E aircraft that has departed or made a low/missed approach by 3 minutes when utilizing opposite direction takeoffs or landings from:

1. The same runway or a parallel runway separated by less than 700 feet.

2. A parallel runway separated by 700 feet or more if projected flight paths will cross.

l. Do not approve pilot requests to deviate from the required intervals contained in subparagraphs f through k.

PHRASEOLOGY− HOLD FOR WAKE TURBULENCE.

REFERENCE− FAA Order JO 7110.126, Para 3−9−7, Wake Turbulence Separation for Intersection Departures.

m. Separate a Category I aircraft behind a Category F or G aircraft that has departed or made a low/missed approach when utilizing opposite direction takeoffs on the same runway by 3 minutes unless a pilot has initiated a request to deviate from the time interval. In the latter case, issue a wake turbulence cautionary advisory before clearing the aircraft for takeoff. Controllers must not initiate or suggest a waiver of the time interval.

NOTE− A request for takeoff does not initiate a waiver request.

n. Inform aircraft when it is necessary to hold in order to provide the required time interval.

3–9–7. WAKE TURBULENCE SEPARATION FOR INTERSECTION DEPARTURES

3–9–7. WAKE TURBULENCE SEPARATION FOR INTERSECTION DEPARTURES

a. Apply the following wake turbulence criteria for intersection departures:

1. Separate a Category I aircraft taking off from an intersection on the same runway (same or opposite direction takeoff) behind a departing Category H aircraft by ensuring that the aircraft does not start takeoff roll until at least 3 minutes after the preceding aircraft has taken off.

2. Separate a Category I aircraft taking off from an intersection on the same runway (same or opposite direction takeoff) behind a departing Category F or G aircraft by ensuring that the aircraft does not start takeoff roll until at least 3 minutes after the preceding aircraft has taken off.

3. Separate a Category I aircraft taking off from an intersection (same or opposite direction takeoff) behind a preceding departing Category E aircraft by ensuring that the aircraft does not start takeoff roll until at least 3 minutes after the Category E aircraft has taken off from:

(a) The same runway or a parallel runway separated by less than 700 feet.

(b) Parallel runways separated by 700 feet or more, or parallel runways separated by 700 feet or more with the runway thresholds offset by 500 feet or more, if projected flight paths will cross.

4. Separate aircraft departing from an intersection on the same runway (same or opposite direction takeoff), parallel runways separated by less than 2,500 feet, and parallel runways separated by less than 2,500 feet with the runway thresholds offset by 500 feet or more, by ensuring that the aircraft does not start take-off roll until the following intervals exist after the preceding aircraft has taken off:

(a) Category B, C, D, E, F, G, H, or I aircraft behind Category A aircraft – 4 minutes.

(b) Category B, C, D, E, F, G, H, or I aircraft behind Category B or D aircraft – 3 minutes.

(c) Category E, F, G, H, or I aircraft behind Category C aircraft – 3 minutes.

NOTE− Apply Para 3-9-6, Same Runway Separation, subpara f, to parallel runways separated by less than 2,500 feet with runway thresholds offset by less than 500 feet.

5. Inform aircraft when it is necessary to hold in order to provide the required time interval.

PHRASEOLOGY− HOLD FOR WAKE TURBULENCE.

NOTE− Aircraft conducting touch-and-go and stop-and-go operations are considered to be departing from an intersection.

REFERENCE− FAA Order JO 7110.65, Para 3−8−2, Touch−and−Go or Stop−and−Go or Low Approach.

b. The time interval is not required when:

1. A pilot has initiated a request to deviate from the time intervals contained in subparagraph a.1 or a.2.

NOTE− A request for takeoff does not initiate a waiver request; the request for takeoff must be accomplished by a request to deviate from the time interval.

b.2. through b.3., No Change

NOTE– Not authorized with a Category A aircraft as the lead or departure aircraft.

No further changes to paragraph

3–9–8. INTERSECTING RUNWAY/INTERSECTING FLIGHT PATH OPERATIONS Title through WAKE TURBULENCE APPLICATION, No Change. 3. Separate an aircraft taking off behind a landing or departing aircraft on an intersecting runway if flight paths will cross (See FIG 3–9–11 and FIG 3–9–12.):

(a) Category B, C, D, E, F, G, H, or I aircraft behind Category A aircraft – 3 minutes. (b) Category B, C, D, E, F, G, H, or I aircraft behind Category B or D aircraft – 2 minutes. (c) Category E, F, G, H, or I aircraft behind Category C aircraft – 2 minutes. (d) Category I aircraft behind Category E aircraft – 2 minutes.

FIG 3–9–11 Departure Behind Departure on Intersecting Runway

FIG 3–9–12 Departure Behind Arrival on Intersecting Runway

No further changes to paragraph

3–9–9. NONINTERSECTING CONVERGING RUNWAY OPERATIONS

3–9–9. NONINTERSECTING CONVERGING RUNWAY OPERATIONS

Title thru WAKE TURBULENCE APPLICATION, No Change

c. Separate aircraft taking off behind a landing or departing aircraft on a converging runway if projected flight paths will cross (See FIG 3–9–18 and 3–9–19):

1. Category B, C, D, E, F, G, H, or I aircraft behind Category A aircraft – 3 minutes.

2. Category B, C, D, E, F, G, H, or I aircraft behind Category B or D aircraft – 2 minutes.

3. Category E, F, G, H, or I aircraft behind Category C aircraft – 2 minutes.

4. Category I aircraft behind Category E aircraft – 2 minutes.

FIG 3–9–18 Converging Runway Separation

NOTE− Takeoff clearance to the following aircraft should not be issued until the time interval has passed from when the preceding aircraft began takeoff roll.

Subparagraph d, delete

FIG 3–9–19 Converging Runway Separation

No further changes to paragraph

3–10–3. SAME RUNWAY SEPARATION

3–10–3. SAME RUNWAY SEPARATION

Title through WAKE TURBULENCE APPLICATION, No Change

b. Issue wake turbulence advisories, and the position, altitude if known, and the direction of flight of departing or arriving aircraft on the same runway or parallel runways separated by less than 2,500 feet to:

1. Category B, C, D, E, F, G, H, and I aircraft behind Category A, B, or D aircraft.

2. Category E, F, G, H, or I aircraft behind Category C aircraft.

3. Category I aircraft behind Category E aircraft.

REFERENCE− AC 90−23, Aircraft Wake Turbulence, Para 12, Pilot Responsibility. FAA Order JO 7110.65, Para 3−10−10, Altitude Restricted Low Approach.

EXAMPLE− 1. “Runway two seven left cleared to land, caution wake turbulence, heavy Boeing 747 departing runway two seven right.”

2. “Number two follow Boeing 757 on 2-mile final. Caution wake turbulence.”

3. “Traffic, Boeing 737 on 2−mile final to the parallel runway, runway two six right, cleared to land. Caution wake turbulence.”

No further changes to paragraph.

3–10–4. INTERSECTING RUNWAY/INTERSECTING FLIGHT PATH SEPARATION

3–10–4. INTERSECTING RUNWAY/INTERSECTING FLIGHT PATH SEPARATION

Title through WAKE TURBULENCE APPLICATION, No Change.

c. Separate aircraft landing behind a departing aircraft on a crossing runway if the arrival will fly through the airborne path of the departure by the appropriate radar separation or the following intervals: (See FIG 3–10–10):

1. Category B, C, D, E, F, G, H, or I aircraft behind Category A aircraft – 3 minutes.

2. Category B, C, D, E, F, G, H, or I aircraft behind Category B or D aircraft – 2 minutes.

3. Category E, F, G, H, or I aircraft behind Category C aircraft – 2 minutes.

4. Category I aircraft behind Category E aircraft – 2 minutes.

d. Issue wake turbulence cautionary advisories including the position, altitude if known, and direction of flight of Category A, B, C, D, or E aircraft to:

REFERENCE ­ AC 90−23, Aircraft Wake Turbulence, Para 11, Pilot Responsibility.

FIG 3–10–10 Intersecting Runway Separation

1. Aircraft landing on a crossing runway behind a departing aircraft that requires wake turbulence separation behind it if the arrival flight path will cross the takeoff path behind the departing aircraft rotation point. (See FIG 3–10–11.)

FIG 3–10–11 Intersecting Runway Separation

EXAMPLE– “Runway niner cleared to land. Caution wake turbulence, Heavy C−Seventeen departing runway one five.”

2. All VFR aircraft landing on a crossing runway behind an arriving Category A, B, C, or D aircraft and VFR Category I aircraft landing on a crossing runway behind a Category E aircraft, if the arrival flight paths will cross. (See FIG 3-10-12.)

FIG 3–10–12 Intersecting Runway Separation

EXAMPLE− “Runway niner cleared to land. Caution wake turbulence, Boeing Seven Fifty Seven landing runway three six.”

REFERENCE FAA Order JO 7110.65, Para 7-4-4, Approaches to Multiple Runways.

No further changes to paragraph

3–10–10. ALTITUDE RESTRICTED LOW APPROACH

3–10–10. ALTITUDE RESTRICTED LOW APPROACH

Title to NOTE-1, No Change

NOTE− 1. The 500 feet restriction is a minimum. Higher altitudes should be used when warranted. For example, 1,000 feet is more appropriate for Category A, B, C, or D aircraft operating over unprotected personnel or Category H or I aircraft on or near the runway.

No further changes to paragraph

3–11–1. TAXI AND GROUND MOVEMENT OPERATION

3–11–1. TAXI AND GROUND MOVEMENT OPERATION

Title through WAKE TURBULENCE APPLICATION, No Change

d. Avoid clearances that require Category H or I aircraft or helicopters to taxi in close proximity to taxiing or hover-taxi helicopters.

No further changes to paragraph

4–8–11. PRACTICE APPROACHES

4–8–11. PRACTICE APPROACHES

Title through a.1.(b), No Change

2. Where procedures require application of IFR separation to VFR aircraft practicing instrument approaches, IFR separation in accordance with Chapters 3 through 7 must be provided. Controller responsibility for separation begins at the point where the approach clearance becomes effective. Except for Category A, B, C, or D aircraft, 500 feet vertical separation may be applied between VFR aircraft and between a VFR and an IFR aircraft.

REFERENCE– FAAO JO 7110.126, Para 5-5-4, Minima, Subparagraphs g and h. FAAO JO 7210.3, Para 6-4-4, Practice Instrument Approaches. FAAO JO 7210.3, Para 10-4-5, Practice Instrument Approaches.

No further changes to paragraph

5–5–4. MINIMA

5–5–4. MINIMA

Title through a.4., No Change

NOTE− Wake turbulence procedures specify increased separation minima required for certain categories of aircraft because of the possible effects of wake turbulence.

b. through f. NOTE 3, No Change

WAKE TURBULENCE APPLICATION

g. Separate aircraft by the minima specified in TBL 5–5–1 in accordance with the following:

WAKE TURBULENCE APPLICATION

1. When operating within 2,500 feet and less than 1,000 feet below the flight path of the leading aircraft over the surface of the earth of a Category A, B, C, or D aircraft.

2. When operating within 2,500 feet and less than 500 feet below the flight path of the leading aircraft over the surface of the earth of a Category E aircraft.

3. When departing parallel runways separated by less than 2,500 feet, the 2,500 feet requirement in subparagraph 2 is not required when a Category I aircraft departs the parallel runway behind a Category E aircraft. Issue a wake turbulence cautionary advisory and instructions that will establish lateral separation in accordance with subparagraph 2. Do not issue instructions that will allow the Category I aircraft to pass behind the Category E aircraft.

NOTE– 1. The application of paragraph 5–8–3, Successive or Simultaneous Departures, satisfies this requirement.

2. Consider runways separated by less than 700 feet as a single runway because of the possible effects of wake turbulence.

REFERENCE– FAA Order JO 7110.65, Para 3–9–6, Same Runway Separation.

TBL 5–5–1 Wake Turbulence Separation for Directly Behind

Follower

A B C D E F G H I

Leader

A 4.5 NM 6 NM 6 NM 7 NM 7 NM 7 NM 7 NM 8 NM

B 3 NM 4 NM 4 NM 5 NM 5 NM 5 NM 5 NM 5 NM

C 3.5 NM 3.5 NM 3.5 NM 5 NM 5 NM

D 3 NM 4 NM 4 NM 5 NM 5 NM 5 NM 5 NM 5 NM

E 4 NM

F

G

H

I

h. ON APPROACH. In addition to subparagraph g, separate an aircraft on approach behind another aircraft to the same runway by ensuring the separation minima in TBL 5–5–2 will exist at the time the preceding aircraft is over the landing threshold.

C 3.5 NM 3.5 NM 3.5 NM 5 NM 5 NM

NOTE− Consider parallel runways less than 2,500 feet apart as a single runway because of the possible effects of wake turbulence.

TBL 5–5–2 Wake Turbulence Separation for On Approach

Follower

A B C D E F G H I

Leader

A 4.5 NM 6 NM 6 NM 7 NM 7 NM 7 NM 7 NM 8 NM

B 3 NM 4 NM 4 NM 5 NM 5 NM 5 NM 5 NM 6 NM

C 3.5 NM 3.5 NM 3.5 NM 5 NM 6 NM

C 3.5 NM 3.5 NM 3.5 NM 5 NM 6 NM

D 3 NM 4 NM 4 NM 5 NM 5 NM 5 NM 6 NM 6 NM

E 4 NM

F 4 NM

G

H

I

i., No Change

j. TERMINAL. 2.5 nautical miles (NM) separation is authorized between aircraft established on the final approach course within 10 NM of the landing runway when operating in single sensor slant range mode and aircraft remain within 40 miles of the antenna, and:

1. Wake turbulence separation must be applied in accordance with TBL 5–5–2;

2. An average runway occupancy time of 50 seconds or less is documented;

3. CTRDs are operational and used for quick glance references;

REFERENCE– FAA Order JO 7110.65, Para 3−1−9, Use of Tower Radar Displays.

4. Turnoff points are visible from the control tower.

No further changes to paragraph

5–8–3. SUCCESSIVE OR SIMULTANEOUS DEPARTURES

5–8–3. SUCCESSIVE OR SIMULTANEOUS DEPARTURES

TERMINAL

Except for when wake turbulence separation is required, separate aircraft departing from the same airport/heliport or adjacent airports/heliports in accordance with the following minima provided radar identification with the aircraft will be established within 1 mile of the takeoff runway end/helipad and courses will diverge by 15 degrees or more.

REFERENCE– FAA Order JO 7110.65, Para 3–9–7, Wake Turbulence Separation for Intersection Departures. FAA Order JO 7110.65, Para 3–9–8, Intersecting Runway/Intersecting Flight Path Operations. FAA Order JO 7110.65, Para 5–5–4, Minima, Subparagraph g.

NOTE 1 through FIG 5–8–3, No Change

FIG 5–8–3 NOTE, REFERENCES, Delete

b. through FIG 5–8–5, No Change

FIG 5–8–5 NOTE, Delete

No further changes to paragraph

6–1–4. ADJACENT AIRPORT OPERATION

6–1–4. ADJACENT AIRPORT OPERATION

TERMINAL

WAKE TURBULENCE APPLICATION The ATC facility having control jurisdiction at adjacent airports must separate arriving or departing IFR aircraft on a course that will cross the flight path of an aircraft requiring wake turbulence separation in accordance with the following:

a. Category B, C, D, E, F, G, H, or I aircraft behind Category A aircraft – 3 minutes.

b. Category B, C, D, E, F, G, H, or I aircraft behind Category B or D aircraft – 2 minutes.

c. Category E, F, G, H, or I aircraft behind Category C aircraft – 2 minutes.

d. Category I aircraft behind Category E aircraft – 2 minutes.

FIG 6-1-1 Adjacent Airport Operation – Arrival

FIG 6-1-2 Adjacent Airport Operation – Departure

6–1–5. ARRIVAL MINIMA

6–1–5. ARRIVAL MINIMA

TERMINAL

WAKE TURBULENCE APPLICATION

a. Separate IFR aircraft landing behind other arriving aircraft to the same runway, a parallel runway separated by less than 2,500 feet, or a crossing runway if projected flight paths will cross:

1. Category B, C, D, E, F, or G aircraft behind Category A aircraft – 3 minutes.

WAKE TURBULENCE APPLICATION

2. Category H or I aircraft behind Category A aircraft – 4 minutes.

3. Category B, C, D, E, F, or G aircraft behind Category B or D aircraft – 2 minutes.

4. Category E, F, or G aircraft behind Category C aircraft – 2 minutes.

5. Category H or I aircraft behind Category B, C, or D aircraft – 3 minutes.

6. Category I aircraft behind Category E aircraft – 3 minutes.

b. Separate IFR aircraft landing behind an arriving aircraft to a parallel runway separated by less than 2,500 feet, or a crossing runway if projected flight paths will cross:

1. Category B, C, D, E, F, G, H, or I aircraft behind Category A aircraft – 3 minutes.

2. Category B, C, D, E, F, G, H, or I aircraft behind Category B or D aircraft – 2 minutes.

3. Category E, F, G, H, or I aircraft behind Category C aircraft – 2 minutes.

4. Category I aircraft behind Category E aircraft – 2 minutes.

FIG 6–1–3 Arrival Minima Landing Behind an Arriving Aircraft Requiring Wake Turbulence Separation

6–7–5. INTERVAL MINIMA

6–7–5. INTERVAL MINIMA

a. Except as provided in subparagraph b, use a 2–minute or 5–mile radar interval as the minimum between successive approaches.

REFERENCE− FAA Order JO 7110.65, Para 5−9−5, Approach Separation Responsibility. FAA Order JO 7110.65, Para 6−7−1, Application. FAA Order JO 7110.65, Para 6−7−2, Approach Sequence.

WAKE TURBULENCE APPLICATION

WAKE TURBULENCE APPLICATION

b. Use the following times or radar intervals as the minimum:

1. Behind Category A aircraft:

(a) Category B, C, or D aircraft – 3 minutes or 6 miles.

(b) Category E, F, or G aircraft – 3 minutes or 7 miles.

(c) Category H or I aircraft – 4 minutes or 8 miles.

2. Category H or I aircraft behind Category B, C, or D aircraft – 3 minutes or 6 miles.

c. Increase the interval as necessary, considering the following:

1. Relative speeds of the aircraft concerned.

2. Existing weather conditions.

3. Distance between the approach fix and the airport.

4. Type of approach being made.

No further changes to paragraph

7–2–1. VISUAL SEPARATION

7–2–1. VISUAL SEPARATION

Visual separation may be applied when other approved separation is assured before and after the application of visual separation. To ensure that other separation will exist, consider aircraft performance, wake turbulence, closure rate, routes of flight, known weather conditions, and aircraft position. Weather conditions must allow the aircraft to remain within sight until other separation exists. Visual separation is not authorized when the lead aircraft is a Category A aircraft.

REFERENCE− FAA Order JO 7110.126, Para 2−1−20, Wake Turbulence Cautionary Advisories. FAA Order JO 7110.65, Para 2−1−21, Traffic Advisories. FAA Order JO 7110.65, Para 3−1−9, Use of Tower Radar Displays. FAA Order JO 7110.65, Para 5−9−5, Approach Separation Responsibility. FAA Order JO 7110.65, Para 7−4−1, Visual Approach. FAA Order JO 7110.65, Para 7−4−2, Vectors for Visual Approach. FAA Order JO 7110.65, Para 7−4−4, Approaches to Multiple Runways. FAA Order JO 7210.3, Para 4−3−2, Appropriate Subjects. FAA Order JO 7210.3, Para 10−3−9, Visual Separation. P/CG Term− Visual Approach. P/CG Term− Visual Separation.

No further changes to paragraph

7–4–3. CLEARANCE FOR VISUAL APPROACH

7–4–3. CLEARANCE FOR VISUAL APPROACH

Title through c.3. NOTE, No Change

d. Inform the trailing aircraft of the lead aircraft’s manufacturer and/or model when wake turbulence separation is required.

EXAMPLE− “Cessna Three Four Juliet, following a heavy Boeing 747, 12 o’clock, seven miles.”

or

“Cessna Three Four Juliet, following a Seven-Fifty-Seven, 12 o’clock, four miles.”

REFERENCE− FAA Order JO 7110.65, Para.2−4−21, Description of Aircraft Types. FAA Order JO 7110.65, Para 5–5–4, Minima, Subparagraph g.

NOTE-­ Visual separation is not authorized when the lead aircraft is a Category A aircraft.

REFERENCE– FAA Order JO 7110.65, Para 7–2–1, Visual Separation.

No further changes to paragraph

7–4–4. APPROACHES TO MULTIPLE RUNWAYS

7–4–4. APPROACHES TO MULTIPLE RUNWAYS

Title through c., No Change

c. In addition to the requirements in Paragraph 7−2−1, Visual Separation, Paragraph 7−4−1, Visual Approach, Paragraph 7−4−2, Vectors for Visual Approach, and Paragraph 7−4−3, Clearance for Visual Approach, the following conditions apply to visual approaches being conducted simultaneously to parallel, intersecting, and converging runways, as appropriate:

1. Parallel runways separated by less than 2,500 feet. Unless approved separation is provided by ATC, an aircraft must report sighting a preceding aircraft making an approach (instrument or visual) to the adjacent parallel runway. When an aircraft reports another aircraft in sight on the adjacent final approach course and visual separation is applied, controllers must advise the succeeding aircraft to maintain visual separation. Do not permit an aircraft to overtake another aircraft when wake turbulence separation is required.

NOTE– Visual separation is not authorized when the lead aircraft is a Category A aircraft.

REFERENCE– FAA Order JO 7110.65, Para 5–5–4, Minima, Subparagraph g. FAA Order JO 7110.65, Para 7–2–1, Visual Separation.

No further changes to paragraph

7–6–7. SEQUENCING

Title through c.1., No Change

2. When parallel runways are less than 2,500 feet apart, do not permit an aircraft to overtake another aircraft established on final within the facility’s area of responsibility when wake turbulence separation is required.

7–6–7. SEQUENCING

REFERENCE– FAA Order JO 7110.65, Para 5–5–4, Minima, Subparagraph g.