Radar Vectors
FAA Order Cancelled Issued Mar 21, 2000 AFS-400 14 pages Copy saved Nov 18, 2026

Order 6750.24D Instrument Landing System and Ancillary Electronic Component Configuration and Performance Requireme

This document is cancelled. Cancelled by 6750.24E. Check the official source before relying on it.

Official source ↗ Open PDF

Text read by OCR from a scanned file. Check the original, as some words may be misread.

U.S. DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION 6750.24D ORDER

U.S. DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION 6750.24D ORDER

3/21/00

SUBJ: INSTRUMENT LANDING SYSTEM AND ANCILLARY ELECTRONIC COMPONENT CONFIGURATION AND PERFORMANCE REQUIREMENTS.

1. PURPOSE. This order specifies the instrument landing system (ILS) and ancillary electronic component configuration and performance requirements for the various categories of low visibility flight operations.

2. DISTRIBUTION. This order is distributed to the director level in the Office of System Safety; to the branch level in the Offices of Airport Safety and Standards, Aviation System Standards, and National Airspace System Implementation; to the Flight Standards, Aircraft Certification, Air Traffic, Air Traffic System Requirements, and Airway Facilities Services; to the branch level in the regional Flight Standards, Air Traffic, Airway Facilities, and Airports Divisions; to all Flight Standards District, and Certificate Management Offices; to all International Field Offices; to all Airport Traffic Control Towers, and Flight Service Stations; to Airway Facilities General National Airspace Sectors, Air Route Traffic Control Center Sectors, and Sector Field Offices and Units; and to all Airports District Offices.

3. CANCELLATION. Order 6750.24C, Instrument Landing System (ILS) and Ancillary Electronic Component Configuration and Performance Requirements, dated August 4, 1993, is canceled.

4. SCOPE. The requirements of this order apply only to public Standard Instrument Approach Procedures (SIAPs) as well as identified special approach procedures.

5. DEFINITIONS.

a. Continuity. Is the quality which relates to the rarity of radiated signal interruptions during any approach. The level of continuity of service of the localizer and/or the glidepath is expressed in terms of the probability of not losing the radiated guidance signals.

b. Integrity. Is the quality that relates to the trust which can be placed in the correctness of the information supplied by the facility. The level of integrity of the localizer and/or the glidepath is expressed in terms of the probability of not radiating false guidance signals.

6. EXPLANATION OF APPENDICES.

a. Appendix 1. Lists the basic ILS ground system components, explains the effect on operations when a component is abnormal or inoperative, and prescribes the action requirements.

Distribution: A-W(SY)-1; A-W(AS/VN/NI/FS/IR/AT/RS/AF)-3; Initiated By: AFS-400 A-X(FS/AT/AF/AS)-3; A-FFS-4, 5, 7, 9 (STD); A-FAT-2, 5 (STD); A-FAF-2, 3, 7 (STD); A-FAS-1 (STD); AMA-200 (80 cys)

b. Appendix 2. Contains the ILS classification system which was developed by the International Civil Aviation Organization (ICAO) All Weather Operations Panel for guidance material in Annex 10 to the Convention on International Civil Aviation. The “Class" designation is used to differentiate between the various performance capabilities of Types I, II, and III ILS equipment, including differences in performance between equipment generically classified as the same “Type."

7. SYSTEM COMPONENT REQUIREMENTS. If Title 14 of the Code of Federal Regulations (14 CFR) part 97, Standard Instrument Approach Procedures, must be amended due to a removed or never-installed component, advise the appropriate Flight Procedures Office and Flight Inspection Office.

a. Localizer and Glide Slope.

(1) Dual transmitters are an installation requirement when the LS will be used to support operations which place a high degree of reliance on ILS guidance for positioning through touchdown. This applies to most Category (CAT) I autoland operations, which require level 3 integrity and continuity of service as described in Appendix 2.

(2) The following is the minimum class of performance (Appendix 2) required for an ILS to support a published part 97 CAT I or III, Standard Instrument Approach Procedure (SIAP):

(a) Class I/T/2 for operations not less than runway visual range (RVR) 1000.

(b) Class I/D/3 for operations not less than RVR 700.

(c) Class III/E/3 for operations not less than RVR 600.

(d) Class /E/4 for operations less than RVR 600.

(3) To maintain the class of performance required for any given operation, the ILS shall be flight inspected and the necessary maintenance inspections performed accordingly. See Appendix 2, paragraph 5, for additional maintenance information on ILS equipment without automated integrity tests.

(4) A request for CAT I or IIIIII operational approval using an ILS with a lower class of performance than specified for a part 97 SIAP may be approved by the Director, Flight Standards Service, AFS-1, if it can be demonstrated that an equivalent level of positioning assurance can be achieved by other means, (i.e., infrared enhancements, millimeter wave radar). Refer to the latest edition of Order 8400.8, Procedures for the Approval of Facilities for FAR Part 121 and Part 135 CAT Operations, and Order 8400.13, Procedures for Approval of Cateogry I Operations and Less Than Standard Category I Operations on Type 1 Facilities.

3/21/00 6750.24D

b. Marker Beacons. An outer marker (or suitable substitute – see paragraph 7c. and Appendix 1) is required for CAT I operations. Middle marker beacons are not required for new Category I ILS installations. An inner marker is required for CAT II operations below RVR 1600 (see Appendix 1).

c. Compass Locator and Distance Measuring Equipment. These aids increase operational flexibility and may be needed for transition to the final approach segment, based on the SIAP design. Also, they may be used as a substitute for the outer marker.

d. Localizer Far Field Monitor (FFM). This equipment provides additional monitoring of the localizer signal in the runway approach area. Although lengthy (15 to 120 seconds typical) time delays are used to prevent nuisance alarms, the FFM is a useful indicator of critical area incursions and localizer antenna array problems not detected by the localizer integral monitors. Installation of FFM equipment is required to support CAT II and I operations. Because of the high degree of reliance placed on the localizer for CAT I automatic landings, the FFM shall be remotely monitored during CAT II/ operations.

e. Runway Visual Range (RVR) System.

(1) Touchdown. A touchdown sensor is an installation requirement for CAT I or I operations.

(2) Midpoint. A midpoint sensor is an installation requirement for all CAT III operations, and for CAT II operations below RVR 1,600 on runways in excess of 8,000 feet.

(3) Rollout. A rollout sensor is an installation requirement for all CAT II operations, and for CAT I operations below RVR 1,600.

f. Approach Lighting Systems. If installed, this equipment supports reduced visibility minima for CAT I operations. An Approach Lighting System with Sequenced Flashing Lights (ALSF), CAT I or II Configuration, is required for CAT III and IIII operations respectively.

g. Touchdown Zone and Runway Centerline Lights. These lights are required for CAT II and III operations and for CAT I operations below RVR 2,400.

h. Runway Edge Lights. Edge lights are required for the approval of straight-in minima at night. A high intensity capability is required for RVR minima and CAT II and II operations.

i. Taxiway Lights. For operations below RVR 600, at least one continuation of taxiway centerline lighting, extending from the runway to the ramp/apron area, is required. All taxiways which are illuminated during these operations shall be provided with red stop bar lights. Stop bar lights shall be controlled by the air traffic control tower when the illuminated taxiway leads into or across any runway being used in operations below RVR 600.

Par 7 Page 3

8. REMOTE MONITORING REQUIREMENTS.

a. General. Order 8260.19, Flight Procedures and Airspace, paragraphs 212 and 213, defines four categories of navigational aids monitoring and the utilization of those monitoring categories. (These categories should not to be confused with categories of flight operations.) The monitoring categories describe combinations of executive (capable of shutdown) and remote status monitoring. For a facility to be used for instrument flight procedures without limitation, both executive and remote status monitors must be operational (monitoring category 1). Consult Order 8260.19 for additional details.

b. CAT II and III Operations.

(1) All ILS or ancillary electronic components which support CAT II and III operations shall be monitored by personnel who are capable of determining whether the combined components' capability can support continued operation following the loss of, or abnormal status of, a required component. The monitoring personnel shall be cognizant of the contents of this order and equipped to carry out the necessary action requirements promptly.

(2) The remote control/status indicator panel for a Type IS (e.g., TI Mark III, Wilcox CAT III, Wilcox Mark 20) is equipped with category status lights in addition to the standard equipment on/off/abnormal lights. The category status lights are intended to conveniently provide the operational status of the ILS to the local control personnel; that is, the lights enunciate the highest category of operation which the ILS is capable of supporting and will downgrade the category following the loss or change to abnormal status of a required system component. Although in some cases this downgrading is more stringent than that required in Appendix 1, the category status lights shall be considered valid and appropriate Notice to Airmen (NOTAM) action shall be initiated, unless the following conditions can be met:

(a) An ILS technician is continuously monitoring the ILS equipment monitor panel. The panel must be displaying the status of all subsystems which normally provide electronic inputs to the category status light circuitry.

(b) The technician has the capability to immediately communicate with air traffic or any other personnel assigned the responsibility of notifying the pilot of an inoperative component or change in operational status per the checklist in Appendix 1.

(c) There is a written agreement between the local airway facilities and air traffic personnel that the category status lights can be disregarded, that the technician will monitor the required parameters and inform air traffic personnel of any change in equipment status, and that air traffic personnel will implement the checklist in Appendix 1.

c. Visual Aid Lights.

(1) Runway edge, centerline, and touchdown zone lights which support CAT II or III operations shall be remotely monitored, or an interim procedure shall be implemented to visually

3/21/00 6750.24D

verify their operation. Remote monitoring systems shall be capable of detecting when more than 10 percent of the lights are inoperative. The lighting system/configuration shall be considered inoperative when more than 10 percent of the lights are not functioning. The interim procedure to visually verify operation of runway edge, centerline, and touchdown zone lights shall assure a visual inspection is conducted prior to the commencement of CAT I or III operations and repeated through physical inspections and/or pilot reports at least every 2 hours thereafter if still in CAT II or IIIII conditions.

(2) Taxiway lights and individual airport/runway lights do not have to be remotely monitored. However, they shall be inspected at an interval which assures that it would be very unlikely that no more than 10 percent of the lights and two adjacent lights would be inoperative, taking into consideration lamp life, environmental conditions, quality of power, etc.

9. RESTORATION REQUIREMENTS. When the visibility at an airport which provides CAT I or II operational service is, or is forecast to be, at or less than 1/2 statute mile, the LS equipment restoration priority shall be level B1 or higher as necessary to support continuous maintenance coverage locations, etc. Refer to the latest edition of Order 6030.31, Restoration of Operational Facilities.

10. LOCALIZER CRITICAL AREAS. The latest edition of Order 6750.16, Siting Criteria for Instrument Landing Systems, describes localizer and glide slope critical areas which shall be marked and protected from parking and the unlimited movement of surface and air traffic, to ensure the continuous integrity of the signal received by the user aircraft.

a. The entire length of the longitudinal axis of the aircraft shall be clear of the critical area when conditions are such that the area must be protected. An aircraft with its longitudinal axis aligned with the edge of a critical area is not considered to be violating the critical area.

b. The worst case alignment of an aircraft for critical area considerations is with its longitudinal axis perpendicular to the runway (e.g., an aircraft departing the runway after landing or taxiing across the runway).

c. The airport authority which controls ground traffic movements must assure that appropriate controls and devices are correctly located, and specific holding instructions implemented when necessary, to protect the critical areas from ground traffic approaching or departing an active runway if the critical area dimension exceeds the distance of the normal runway holding position marking from the runway centerline. Also, procedures must be implemented to determine when an aircraft is clear of the critical area when exiting the runway. Taxiway centerline lead-off lights, where installed, shall be color-coded as alternating green and yellow to denote the critical area. For taxiways not equipped with centerline lights, a “Critical Area Boundary" sign may be installed on the back side of the ILS sign to indicate the critical area boundary.

d. Where the standard critical area has a significant adverse impact on a specific taxi route, etc., it may be possible through operational constraints to provide relief on a case-by-case

Par 8 Page 5

basis (e.g., considering the varying size of aircraft). Mathematical modeling techniques are readily available to facilitate this consideration.

11. DIRECTIVE FEEDBACK. Any deficiencies found, clarifications needed, or suggested improvements regarding the content of this order should be forwarded to the originating office, Attention: Directives Management Officer, for consideration. Your assistance is welcome. Federal Aviation Administration Form 1320-19, Directive Feedback Information, is located on the last page of this order for your convenience. If an interpretation is urgently needed, you may call the originating office for guidance, but you should also use the tearout sheet as a follow up to verbal conversation.

L. Nicholas Lacey Director, Flight Standards Service.

Component Situation

Localizer One transmitter is (LOC) and inoperative. Glide Slope (GS) NOTE: 2 transmitters required to commence CAT II or CAT III operations.

Far Field At least one sensor Monitor (FFM) (receiver subsystem) Sensor(s) operating & not in alarm

All sensors (receiver subsystems) inoperative or in alarm

NOTES:

(1)

APPENDIX 1. ABNORMAL CHECKLIST

APPENDIX 1. ABNORMAL CHECKLIST

CAT Effect Action Requirement 3/21/00

1 No effect Corrective maintenance

No effect if one transmitter fails during CAT II Expedite corrective maintenance operations. See NOTE 1.

111 Denies CAT IIl operations below RVR600 The facility/organization responsible shall ensure that appropriate NOTAM action is NOTE 1: Should weather improve to CAT I for at taken, and expedite corrective least four hours and subsequently deteriorate to maintenance. CAT II/III conditions, standby equipment must be restored prior to resuming CAT Il/IIl operations. All No effect Corrective maintenance

1 No effect Corrective maintenance

All If ILS critical areas are known to be clear, continue Cat I -- Corrective maintenance operations. Should weather improve to CAT I for at least four hours and subsequently deteriorate to Cat II & IlI - Expedite corrective CAT II/III conditions, FFM sensor(s) must be maintenance restored prior to resuming CAT II/IIí operations. (NOTE: FFM installation not required for CAT I operations; if installed, however, use the preceding text.)

Where the action requirement is to inform the aircraft of the inoperative component situation, do so in accordance with the latest edition of Order 7110.65, Air Traffic Control, in paragraphs 4-70 (4-6-1), Airport Conditions, and 3-32 (3-3-3), Timely Information. Pilots will adjust minima/discontinue operations predicated on the inoperative component notification in accordance with the inoperative components table, the approved operations specifications, and/or Federal Aviation Àdministration (FAA) ietter of authorization.

(1)

Where the action requirement is to Initiate a Notice to Airmen (NOTAM) to disallow the operation, do so in accordance with the latest edition of Order 7930.2, Notices to Airmen, in the section on NAVAIDS, Communlcations Outlets, and Service.

"CAT" (Category) INDICATES THE OPERATION BEING CONDUCTED OR APPROVED

(2)

Page 1

Appendix 1 6750.24D

Appendix 1 6750.24D

Page 2

Component Situation

FFM Remote Status indications not Monitoring available or abnormal Indicator (e.g., remoting lines out of service, FFM bypassed); NOTE: These indications typically have time delays of 15-120 seconds. LOC or GS One monitor in a dual- Executive channel system fails, (Integrity) reducing system Monitors integrity level. (excludes FFM function)

Outer Marker Inoperative Beacon (OM); Compass Locator (COMLO); Distance Measuring Equipment (DME) Middle Marker Inoperative Beacon (MM)

CAT

All

11

All

All

APPENDIX 1. (continued)

APPENDIX 1. (continued)

Effect Action Requirement Appendix 1 6750.24D

If ILS critical areas are known to be clear, continue Cat I -- Corrective maintenance operations. Should weather improve to CAT I for at least four hours and subsequently deteriorate to Cat II & III - Expedite corrective CAT I/II conditions, FFM sensor(s) must be maintenance restored prior to resuming CAT Il/IIi operations. (NOTE: FFM installation not required for CAT operations; if installed, however, use the preceding text.)

No effect (dual monitors not required) Corrective maintenance

No effect if fails during CAT Il operations. Should Expedite corrective maintenance weather improve to CAT I for at least four hours and subsequently deteriorate to CAT Il conditions, failed monitor must be restored prior to resuming operations.

Denies operations Initiate NOTAM action and expedite corrective maintenance If the final approach fix (FAF) can be identified by Notify aircraft; initiate NOTAM action and one or more of these facilities and/or another corrective maintenance NAVAID (e.g., radar), or published waypoint, there is no effect." If the FAF cannot be identified (e.g., no method available for timing of descent), nonprecision operations cannot be conducted.

No effect Notify aircraft; initiate NOTAM action and corrective maintenance

3/21/00

Component Situation

Inner Marker Inoperative Beacon (IM)

Touchdown Inoperative RVR (Somne operators using aircraft equipped with failoperational rollout control systems are authorized to continue operations with any one transmissometer temporarily inoperative) Midpoint RVR Inoperative (Some operators using aircraft equipped with failoperational rollout control systems are authorized to continue operations with any one transmissometer temporarily inoperative)

Rollout RVR Inoperative (Some operators using aircraft equipped with failoperational rollout control systems are authorized to continue operations with any one transmissometer temporarily inoperative)

Page

3

CAT

1

111 1

I&lll

1

1

11

APPENDIX 1. (continued)

Effect

No effect

Limits lowest visibility to RVR 1600 unless aircraft equipped with radio altimeter and Standard Instrument Approach Procedure (SIAP) does not prohibit its use.

No effect Increases CAT I minima to 1/2 mile

Denies operations

No effect

Increase CATIl minima to RVR 1600 unless rollout RVR is operative -- i.e., rollout can be used as a substitute.

Denies operations

No effect

Required for minima below RVR 1600 unless midpoint RVR is operative -- i.e., midpoint can be used as a substitute.

Denies operations

Action Requirement 3/21/00

Notify aircraft; initiate NOTAM action

Notify aircraft; initiate NOTAM action

Notify aircraft; initiate NOTAM action Notify aircraft of the inoperative component, and initiate NOTAM action.

Notify aircraft of the inoperative component, and initiate NOTAM action. Expedite corrective maintenance.

Notify aircraft of the inoperative component, and initiate NOTAM action.

Notify aircraft of the inoperative component, and initiate NOTAM action. Expedite corrective maintenance.

Notify aircraft of the inoperative component, and initiate NOTAM action. Expedite corrective maintenance. Notify aircraft of the inoperative component, and initiate NOTAM action.

Notify aircraft of the inoperative component, and initiate NOTAM action. Expedite corrective maintenance.

Notify aircraft of the inoperative component, and initiate NOTAM action.

Expedite corrective maintenance. Appendix 1 6750.24D

Page 4

Component

Approach Lighting System (Éxcluding ŠFL/RAIL)

Approach Lighting System

Power Source for Approach Lighting System (Éxcluding SFL/RAIL) Sequence Flashing Lights (SFL/RAIL)

Standby Power Source for SFL/RAIL

Situation

Inoperative

ALSF being operated as SALSR

Main or standby (commercial) power source inoperative

Inoperative

Inoperative

CAT

1

1

II & IIII1

II & IIII1

II&IIIIII

1

1

I

11

APPENDIX 1. (continued)

Effect

Increases visibility to 3/4 mile or RVR 4000

Denies operations

No effect

CATIl and all CATIIl operations are permitted, provided the ALS can continue to operate as a SALS.

No effect

Denies operations unless lights can be visually or are remotely monitored continuously, and aircraft can be informed immediately if a failure occurs.

APPENDIX 1. (continued)

RAIL: Increases visibility to 3/4 mile or RVR 4000 SFL: No effect

Denies operations

No effect No effect

Denies operations unless lights can be visually or are remotely monitored continuously, and aircraft can be informed immediately if a failure occurs.

No effect

Action Requirement Appendix 1 6750.24D

Notify aircraft of the inoperative component, and initiate NOTAM action.

Notify aircraft of the inoperative component, and initiate NOTAM identifying inoperative component. Expedite corrective maintenance. Notify aircraft ALSF is inoperative as above. Issue NOTAM indicating ALSF RWYXX Inop. SALSR Approach Lighting System is available UFN (date). With notation that CATII operators verify CATIl with SALSR authorization. None

Initiate NOTAM action and expedite corrective maintenance.

Notify aircraft of the inoperative component, and initiate NOTAM action.

Notify aircraft of the inoperative component, and initiate NOTAM action. Expedite corrective maintenance.

Expedite corrective maintenance. None

Initiate NOTAM action and expedite corrective maintenance.

Initiate NOTAM action and expedite corrective maintenance.

3/21/00

Component Situation

Standby Power Inoperative Source for TDZL and/or RCLS Lights

Runway Edge More than 10% of the Lights runway edge lights are not functioning

Standby Power Inoperative Source for Runway Edge Lights

Taxiway Visibility is less than Centerline RVR 600, and more Lights than 10% of the lights on the active taxiway(s) are not functioning

Page 5 (and 6)

CAT

l1

111 1

1&11

APPENDIX 1. (continued)

Effect

No effect

Denies operations unless lights can be visually or are remotely monitored continuously, and aircraft can be informed immediately if a failure occurs.

Denies operations Day: Minima below RVR 2,400 not authorized. Night: Denies TITLE 14 CFR Part 97 straight-in landing minima

Denies operations

No effect

Denies operations unless lights can be visually or are remotely monitored continuously, and aircraft can be informed immediately if a failure occurs. Not Applicable

Denies operations below RVR 600 unless alternate procedures have been approved by Air Traffic and Flight Standards.

Action Requirement 3/21/00

None

Initiate NOTAM action and expedite corrective maintenance.

Initiate NOTAM action and expedite corrective maintenance. Notify aircraft of the inoperative component, and initiate NOTAM action.

Notify aircraft of the inoperative component, and initiate NOTAM action. Expedite corrective maintenance. None

Notify aircraft of the inoperative component, and initiate NOTAM action. Expedite corrective maintenance. None

Notify aircraft of the inoperative component, and initiate NOTAM action. Expedite corrective maintenance.

Appendix 1 6750.24D

Appendix 1 6750.24D

3/21/00 6750.24D Appendix 2

APPENDIX 2. ISTRUMENT LANDING SYSTEM (ILS) CLASSIFICATION SYSTEM

1. The ILS classification system specified in this appendix provides a more comprehensive method of describing ILS performance than the Facility Performance Category (CAT) method alone.

APPENDIX 2. ISTRUMENT LANDING SYSTEM (ILS) CLASSIFICATION SYSTEM

2. A. facility's “Class" of performance is defined by using three characters as follows:

a. I, II, or III: With the exception of Localizer Facility Performance CAT IIII course structure, this character indicates conformance to the facility performance category standards contained in the International Civil Aviation Organization (ICAO) Annex 10, unless superseded by a Federal Aviation Administration (FAA) directive.

b. A, B, C, T (Threshold), D, or E: This character defines the ILS point to which the localizer conforms to the Facility Performance CAT II course structure tolerances.

c. 1, 2, 3, or 4: This number indicates the level of integrity and continuity of service given in Appendix 2, Table 1.

(1) Level 1 rated ILS equipment is used to support low visibility operations for which positioning guidance below approximately 200 feet height above touchdown (HAT) is provided by other means, such as visual cues.

(2) Level 2 rated ILS equipment is used to support reduced visibility operations for which positioning guidance below 100 feet HAT is supplemented by other means, such as visual cues.

(3) Level 3 rated ILS equipment is used to support operations which place a high degree of reliance on ILS guidance for positioning through touchdown.

(4) Level 4 rated LS equipment is used to support operations which place a high degree of reliance on ILS guidance throughout touchdown and rollout.

3. As an example, an ILS that conforms to the ICAO Annex 10 Facility Performance CAT standards, meets the CAT III localizer course structure criteria to ILS point “D," and conforms to the integrity and continuity of service objectives of level 3 would be described as “Class ID3." An ILS which conforms to ICAO Annex 10 Facility Performance CAT I standards, has a localizer CAT III course structure to point “E," and conforms the integrity and continuity of service objectives of level 2 would be described as “Class IE2." However, when facility performance standards are monitored to CAT II standards, this same facility having a localizer CAT III course structure to point “E," and conforming to the integrity and continuity of service objectives to level 2 would be described as “Class IIE2."

6750.24D 3/21/00 Appendix 2

APPENDIX 2. (continued)

APPENDIX 2. (continued)

Table 1. -- Minimum Localizer (LOC) and Glide Slope (GS) Integrity and Continuity Levels

Level Integrity Continuity MTBO (Hours)

1 Not demonstrated, or less than required for Level 2

2 1 - 1x10-7 in any one 1 - 4x10-6 in any period 1000

landing of 15 seconds

1 Not demonstrated, or less than required for Level 2

3 1 - 0.5x10-9 in any one 1 - 2x10-6 in any period 2000

landing of 15 seconds

4 1 - 0.5x10-9 in any one 1 - 2x10-6 in any period

landing of: 30 seconds (LOC) 4000 (LOC)

15 seconds (GS) 2000 (GS)

NOTES:

1. Some earlier design ILS equipment types have been determined to require minimum demonstrated Mean Time Between Outage (MTBO) performance, and/or manual integrity tests, to conform to the Integrity and Continuity level requirements of Table 1. Texas Instruments Mark IIII, Wilcox Category III (also known as Mark III and Mark I), and GRN-27 IILS equipment must exhibit the MTBO values in Table 1.

2. In addition to the MTBO requirements, the GRN-27 ILS must pass a weekly (Level 2) or Daily (Levels 3 and 4) manual integrity test. This is accomplished by simulating a monitor fault and confirming that the appropriate automatic equipment transfer or shutdown occurs. For example, if a GRN-27 ILS supports CAT I operations, the integrity test must be performed every 24 hours, or prior to allowing landing operations below runway visual range (RVR) 1,200, and repeated every 24 hours thereafter if CAT I conditions continue to exist. If the required integrity cannot be maintained, CAT III operations are not authorized and may not continue, and Notice to Airmen (NOTAM) action must be taken.

3. Mean Time Between Outage (MTBO) is calculated by dividing a facility's total in service time by the number of unanticipated operational outages during the same period. For existing facilities, it is determined using historical data that has been established over at least a one-year period. Pending actual performance data for new or upgraded facilities, it can be determined by using the anticipated performance record that can be RÉASONABLY expected considering the past performance of similar facilities using the same equipment and installation procedures.

4. Additional information on integrity and continuity of service is contained in Attachment C to Part 1 of the ICAO Annex 10, Volume I.

5. As of March 1998, ICAO has proposed changes to ICAO Annex 10 as a result of AWOP 16. Some of the proposals affect integrity and continuity requirements, and these changes have NOT been included in Appendix 2, Table 1.

U.S. Department of Transportation Federal Aviation Administration

Directive Feedback Information

Please submit any written comments or recommendations for improving this directive, or suggest new items or subjects to be added to it. Also, if you find an error, please tell us about it,

Subject: Order _6750.24D, Instrument Landing System (ILS) and Ancillary Electronic Component Configuration and Performance Requirements

To: Directive Management Officer,

(Please check all appropriate line items)

An error (procedural or typographical) has been noted in paragraph on page

Recommend paragraph on page be changed as follows: (attach separate sheet if necessary)

In a future change to this directive, please include coverage on the following subject (briefly describe what you want added):

Other comments:

I would like to discuss the above. Please contact me.

Submitted by: Date:

FTS Telephone Number: Routing Symbol:

FAA Form 1320-19 (8-89)