Radar Vectors
FAA Order Current Issued Dec 30, 1987 ADS-110 22 pages Copy saved Nov 17, 2026

Order 6740.6 U.S. National Aviation Standard for the Nondirectional Beacon (NDB) Automatic Direction Finder (ADF) System

Official source ↗ Open PDF

ORDER 1 6740.6

U.S. NATIONAL AVIATION STANDARD FOR THE NDB/ADF SYSTEM

12/ ?fJ/87

DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

Distribution: A-W( FS/WS/PO/IA/EU/ES/PM/TO/TR)-3; A-W(VN )-2; Initiated By: AES-31 0 A-X(AF)-3; A-Z-3; A-FAF-0

FOREWORD

During the early 1960's, many thought that NDB's would disappear with the wide implementation of VOR/DME/TACAN. However, while the NDB has evolved from a primary to a secondary navigation aid, it has hardly disappeared. Quite to the contrary, it now outnumbers VOR stations by a factor of more than 2 to 1. No end of service is foreseen between now and the year 2000 because of the wide

FEDERAL AVIATION ADMINISTRATION

and increasing acceptance by aviation users and the lack of an acceptable replacement system.

The NDB/ADF System, like most aeronautical systems, will continue to evolve in response to user needs. The number of FAA NDB's will remain stable and future growth primarily will be non-Federal in nature. As the system evolves, proper operation and compatibility among elements of the system must be maintained. This order is intended to provide guidance in this endeavor.

Under the Federal Aviation Act of 1958, as amended, 49 USC Section 1301 et seq., the FAA is charged with providing for the regulation and promotion of civil aviation in order to best foster its development and safety, and to provide for the safe and efficient use of the airspace by both civil and military aircraft. Explicitly, the Administrator shall develop, modify, test,

and evaluate systems, procedures, facilities, and devices defining their performance characteristics as needed. This effort is directed toward meeting the need for safe and efficient navigation and traffic control of all civil and military aircraft operating in a common civil/military National Airspace System.

-· ,-" {~~

Administrator

Page i (and iil

12/30/87 6 7 40. 6

TABLE OF CONTENTS

TABLE OF CONTENTS

Page No.

CHAPTER 1. GENERAL 1

1. Purpose 1 2. Distribution 1 3. Definitions 1 4. Authority to Change This Order 1 5. Applicability 1 6. The NDB/ADF System Characteristics 1 7.-19. Reserved 2

CHAPTER 2. NDB/ ADF SYSTEM 5

20. NDB/ADF System Description 5 21. Rated Coverage Volume 5 22. Effective Coverage Volume 5 23. Operational Service Volume 5 24. Standard Service Volumes 5 Figure 2-1. NDB Service Volume Ranges 5 25. Service Limitations Due to Ionospheric Reflections 6 26. Radiofrequency (RF) Allocations 6 27. Frequency Congestion 7 28. Station Passage 7 29. Station Identification Code Characteristics 7 30. Identification Code 8 31. Station Voice Transmissions 8 32. Airborne Components 8 33. NDB/ADF-Bearing Accuracy 8 34. Use of Other Than NDB Ground Stations 9 35. En Route Use of NDB's 9 36. Use of an NDB as a Compass Locator (COMLO) 9 37. Nonprecision Approach, NDB Location 9 38. Flags and Warnings 9 39. Pilot Monitoring During Use 10 40.-59. Reserved 10

CHAPTER 2. NDB/ ADF SYSTEM 5

Page iii

6740.6 12/30/87

Page No.

CH~PTER 3. OPE~TION~L CH~~~CTERISTICS OF NOB GROUND 17

ST~TIONS

60. Introduction 17 61. Emission Characteristics 17 62. Frequency Tolerance 17 63. Field Strength 17 64. Power Limitations 18 65. Single Carrier NOB's 18 66. Dual Carrier NDB 1 s 18 67. Identification Code Modulations 18 68. Monitoring 18 69. Grounding 18 70.-89. Reserved 18

CH~PTER 4. OPER~TION~L CH~R~CTERISTICS FOR ~DF COMPONENTS 23

CH~PTER 4. OPER~TION~L CH~R~CTERISTICS FOR ~DF COMPONENTS 23

90. Introduction 23 91.. Receiver Sensitivity 23 92. Receiver Selectivity 23 Figure 4-l. Current ADF Receiver Selectivity 23 Figure 4-2. Future AOF Receiver SeLectivity 24 93. Station Identification 24 94. Bearing Information 24 95. Bearing ~ccuracy 24 96. Radiation 24 97. DeV'elopment of Flag and t.Jarning Functions 24

~PPENDIX l. DEFINITIONS ~ND ~CRONYMS (2 Pages) 1

~PPENDIX 2. SYSTEM BE~RING ~CCU~CY (3 Pages) l Figure l. Combined Error Determination 2

~PPENDIX 3. NOB FREQUENCIES 1

~PPENDIX 3. NOB FREQUENCIES 1

Page iv

l~!~0/87 6740.6

CHAPTER 1. GENERAL

1. PURPOSE. This order establishes the Nondirectional Beacon (NDB) Automatic Direction Finder (ADF) U.S. National Aviation Standard defining the performance required of the system and its components. This standard defines the application and performance characteristics as well as some operational

CHAPTER 1. GENERAL

limitations and restrictions for NDB and ADF equipment in the United States. For ground and airborne components, this material identifies signal, functional, and performance characteristics required to meet operational requirements and

to provide compatibility between components of the system.

2. DISTRIBUTION. This order is distributed to branch level in the Offices of Flight Standards, Airworthiness, Aviation Policy and Plans, International Aviation, Europe, Africa, and Middle East Office, Systems Engineering Service, Program Engineering and Maintenance Service, Air Traffic Operations Service,

and Air Traffic Plans and Requirements Service; division level in the Aviation Standards National Field Office; branch level in the regional Airway Facilities Divisions and the FAA Technical Center; and to the Airway Facilities Field and Sector Offices.

3. DEFINITIONS. Appendix 1, Definitions and Acronyms, contains the definitions and acronyms used in this order.

4. AUTHORITY TO CHANGE THIS ORDER. The Director, Systems Engineering Service, may issue changes to this order. The Administrator reserves the authority to approve changes which establish policy, delegate authority, or assign responsibility.

5. APPLICABILITY. The National standard applies to all NDB ground equipment and ADF airborne equipment used in the National Airspace System (NAS).

6. THE NDB/ADF SYSTEM CHARACTERISTICS.

a. The ADF component characteristics apply in entirety to those components used in aircraft operations performed under Instrument Flight Rules

(IFR). However, for other aircraft operations, the applicability is limited to requirements identified in chapter 4 as essential to prevent impairment of services to other NAS users.

b. In all cases where a parameter and associated tolerance is identified herein, ground stations shall be maintained within these limits by quality

assurance methods including monitoring, periodic ground or flight inspections, or a combination of these methods.

c. Operators of airborne systems designed, installed, and operated in accordance with this order can expect to achieve the system performance which

the order js designed to provide.

Chap 1 Par l Page l

6740.6 12/30/87

d. It is recognized that certain existing NDB equipment characteristics may not comply with all requirements of this order. Specific NDB equipment characteristics that are identified which deviate from the requirements of this order will be corrected or replaced as practical; but not later than l year

from the date of this order unless a waiver is authorized by the cognizant regional office.

7.-19. RESERVED.

Chap Page 2 (thru 4) Par 6

l

CHA.PTER 2. NDB/ A.DF SYSTEM

CHA.PTER 2. NDB/ A.DF SYSTEM

20. NDB/A.DF SYSTEM DESCRIPTION. Tne NDB/A.DF System is a snort distance air navigation system. The ground component provides properly equipped aircraft with bearing and identification referenced to the selected ground component. The system provides navigation signals to all civil and military aviation for

the safe and efficient conduct of aircraft operations, exercise of air traffic control, and use of airspace. The NOB is an International Civil Aviation Organization standard navigation aid. The NOB/ADF System nas been allocated radio spectrum in the aeronautical radionavigation service. The primary purpose of the NDB/ADF System is for navigation. While other services may be provided by the system, they are less important than the navigation information. The identification signal is an integral part of the navigation signal since, without the identification, the navigation information cannot be validated.

21. RATED COVERAGE VOLUME. Rated coverage is the volume of airspace around an NOB, within whicn the strength of the vertical field of the groundwave meets or exceeds the minimum field strength as specified in paragraph 63a.

22. EFFECTIVE COVERA.GE VOLUME. Effective coverage is tne volume of airspace around an NOB, within which bearings can be obtained with a total system accuracy of 10 degrees to the right or left of course. In general, a facility's effective coverage volume is smaller than the rated coverage volume.

23. OPERA.TrONA.L SERVrCE VOLUME. Operational coverage is tne volume of airspace around an NDB which is advertised by the FAA as available for airborne use. The operational coverage shall not exceed the rated coverage or the effective coverage on any azimutn or at any elevation. NOB's are available for use within their operational service volumes. Outside this airspace reliable service may not be available.

24. STA.NDA.RD SERVICE VOLUMES. NOB's are classified according to their intended use. The ranges of NDB service volumes are sho~n in figure 2-1. The distances (radius) are tne same at all altitudes.

FIGURE 2-l. NOB SERVICE VOLUME RA.NGES

CLA.SS orsTANCE (RA.DIUS)

COMLO 15 nmi

MH 25 nmi H 50 nmi HH 75 nmi

FIGURE 2-l. NOB SERVICE VOLUME RA.NGES

NOTE: Service volume ranges of individual facilities may be less than that indicated. Restrictions to service volumes are first publisned in the Notice to A.irmen (NOTA.M) and tnen with tne alphabetical listing of tne navigation aid (NAVA.ID) in tne A.irport/Facility Directory.

Cnap 2 Par 20 Page 5

6 7 40. 6 12/30/87

25. SERVICE LIMITATIONS DUE TO IONOSPHERIC REFLECTIONS. ;,ow fre0,ency (LF) radiation propagates both as a groundwave and as a skywave. The groundwave is used for navigation. The skywave is generally un~e1ia~le fo~ navigational use due to bearing inaccuracies. A given NOB

1 s g;:-oundwave is so:2:~tines simultaneously receivable with a skywave which can cause interference and degrade, or make unusable, the navigation signal. This inte~:erence can occur in two ways called "night effect" and "skywave interference ...

a. Skywave interference is a situation in which any skywave is large enough to interfere with a given NDB's groundwave. At night, the reflective properties of the ionosphere increase and the skywave can be substantially

larger than during the day. When a skywave is large enough to interfere with a groundwave, this situation is aptly called "skywave interference." When the skywave of a facility interferes with its own groundwave, this type of skywave

interference is called "night effect. •• Skywave interference is subject to diurnal, seasonal, and irregular changing properties of the ionosphere. It is not possible to predict precisely when and where skywave interference will occur or the severity of its effect on the NDB/ADF System operations. Skywave interference manifests itself in one or more of the following ways: erroneous bearings, "hunting" of the ADF needle, garbling of the identification signal,

and/or the presence of atore than one identification signal.. Skywave interference is most likely to occur from shortly before sundown until shortly after sunrise.

b. Night effect is a situation in which the groundwave and skywave of a given NDB are simultaneously receivable at large distances from the NDB. Tflhen this occurs, it is unlikely that reliable bearings can be obtained if the groundwave does not exceed the skywave by at least 10 decibels (dB). In most cases, this is not an operational concern because NDB's are generally used at short ranges as terminal or transition facilities. At short range night effect is not a problem. At very long ranges, however, night effect can present bearing accuracy problems .. Therefore, the maximum operational service volume shall not extend beyond the range where the groundwave will exceed the skywave by 10 dB. The maximum allowable range is dependent on the NDB frequency and on ground conductivity. However, it is independent of NDB power since increasing the transmitter power increases both the groundwave and the skywave ..

26. RADIOFREQUENCY (RF) ALLOCATIONS. The NDB/ADF System is allocated radio spectrum in the aeronautical radionavigation service. Specific frequencies allocated for NDB/ADF use are listed in Appendix 3, NDB Frequencies.

Chap 2 Page 6 Par 25

12j:iJ/87 6740.6

27. FREQUENCY CONGESTION.

a. Background. During the 1975-1985 time period, there was a dramatic growth in the number of NDB's. Of the more than 2,000 NOB's in this country, over two-thirds are non-Federal ground .stations. Growth in the number of non-Federal systems has been many times larger than growth in the number of Federal systems. This trend is expected to continue. Eventually, the NDB/ADF System will be replaced; however, at this time the replacement system has not been identified. No end of service can be foreseen in this century because of the wide and increasing user acceptance and the lack of an acceptable, proven replacement system.

b. Congestion. NDB frequency congestion has been a longstanding problem both in this country and in Europe. In the United States, congestion is most severe in California, along the East Coast, and along the Gulf of Mexico. In these and other areas, frequency congestion makes it difficult or impossible to make frequency assignments for new NDB's. In an effort to alleviate this problem, the FAA requested that the Radio Technical Commission for Aeronautics

(RTCA) form a special committee to develop and recommend improved ADF standards. This effort was completed and the resulting standards were published in 1982. In the long term, the tighter selectivity of such avionics will provide some relief to the congestion problem. In the near term, however, frequency congestion will continue to constrain the number of new NDB assignments which can be made.

28. STATION PASSAGE. The sharp reduction in signal strength directly over the station known as the cone of confusion or cone of silence shall not exceed a total of 40 degrees (i.e., ~20 degrees as measured from the vertical above the NDB).

29. STATION IDENTIFICATION CODE CHARACTERISTICS. Each NDB shall transmit an identification signal in International Morse Code at least three times each 30 seconds, equally spaced within that interval. Voice identification shall not be permitted. The characteristics of the identification code shall be as follows:

a. The dots shall be a time duration of 0.1 second to 0.125 second and the dashes shall be three times the duration of a dot.

b. The time between dots and dashes of a code letter shall be the length of a dot.

c. The time between consecutive letters of the identification code group shall be the length of three (3) dots.

Chap 2 Par 27 Page 7

6740.6 12/30/87

30. IDENTIFICATION CODE. The NDB identification code shall be as follows:

a. Standard Identification Code. With the exception of the two cases outlined in subparagraphs band c, all NDB's shall transmit a three-letter

identification code. This code shall be transmitted at intervals equal to sixty-four (64) dot lengths.

b. Compass Locator (COMLO). COMLO's shall transmit a two-letter identification code derived from the identification code of the instrument landing system (ILS) with which it is associated. The identification code shall be transmitted at intervals equal to forty-eight (48) dot lengths.

c. 'IDB's That Are Not Part of the NAS. With NDB's that are not a part of the NAS, it is permissible to add one digit to the standard three-letter identific3tion code. This four-character code (three letters, one number) shall be transmitted at intervals equal to eighty {80) dot lengths.

d. Code Suppression. The NDB identification code shall not be suppressed during voice transmissions.

e. Absence of Identification. The absence of an identification code shall serve as an indication that the NDB is unusable or out of service.

31. STATION VOICE TRANSMISSIONS. The NDB can be used as an outlet for automated weather observing system and other weather system broadcasts until an alternate method of disseminating this information becomes available. However, the primary purpose of NDB

1 s is to provide ·navigational aid and, therefore, NDB's should not be retained solely to satisfy voice broadcast requirements. The quality of voice transmission from an NDB can be a problem because of antenna bandwidth limitations and susceptibility to noise from manmade and natural sources. When installed, NDB voice coverage will be usable to at least two-thirds of the rated service volume.

32. AIRBORNE CO~PONENTS. Airborne components of the system consist of ADF equipment which conforms to the requirements of chapter 4 of this order.

33. NDB/ADF-BEARING ACCURACY. The basic purpose of an NDB is to allow an AUF-equipped aircraft to fly from point A to point B and to stay within a defined airspace in the process. For terminal and transition NDB 1s, this airspace is the obstacle clearance zone. This zone is based on NDB- and ADFbearing accuracy. The total system accuracy is approximately +10 degrees. {See appendix 2).

Chap 2 PqeB Par 30

34. USE OF OTHER THAN NDB GROUND STATIONS. In addition to NDB's, ADF receivers can also receive and process signals from amplitude modulation (AM) broadcast stations, maritime radio beacons, and several other types of

stations. Pilots have used such stations as aids during a visual flight rules (VFR) flight for a long time. However, these stations are neither flight inspected nor a part of the NAS. A VFR flight using such ground stations as a sole means of navigation is uncertified; pilots fly at their own risk. An IFR flight using such ground stations shall not be permitted.

35. EN ROUTE USE OF NDB'S. Except as noted in subparagraphs a, b, and c, NDB's will not be used as en route navigation aids.

a. NOB's may be used as en route aids in Alaska when other NAVAID 1 s are unavailable. Airspace protection shall be increased to compensate for the accuracy limitations in such cases.

b. NDB's may be used on a temporary basis as substitute NAVAID 1 s to support an air route when a Very High Frequency Omnidirectional Radio Range is out of service.

c. NDB's may be used together with Distance Measuring Equipments for the air route structure system. This may include terminal approaches in Alaska.

36. USE OF AN NDB AS A COMLO. When an NDB is colocated with a marker beacon and used in conjunction with an ILS, it is commonly referred to as a COMLO. Where a COMLO is used as a supplement to an ILS, it should be located at the

outer marker beacon site. Due to the frequency congestion in the LF and medium frequency bands, use of a COMLO at the middle marker, in addition to one at the outer marker, is not recommended.

37. NONPRECISION APPROACH, NDB LOCATION. Where an NDB serves as a final approach fix in the absence of an ILS, the NDB should be located at a site equivalent to an outer marker site. Site selection shall take into account the appropriate obstacle clearance requirements.

38. FLAGS AND WARNINGS. Unlike most navigation aids, the NDB/ADF System generally does not provide a warning or a flag if the received signal is deficient in level or quality. The pilot must determine whether the received signal is reliable by listening to the identification and observing the needle movements. The reception of two different identification signals simultaneously or the lack of any identification means that the ADF bearing is unreliable. Similarly, unusual needle variations are also an indication of unreliable bearing. Since the NDB/ADF System provides no other warning or flag, the pilot must monitor both station identification and ADF needle variation while making use of the NDB/ADF System.

1\

Chap 2 Par 34 Page 9

6740.6 12/ ?JJ/87

39. PILOT MONITORING DURING USE. ADF navigation requires that the pilot monitor the audio output of the ADF receiver (i.e., the NDB identification and all other received signals including background noise) and the needle action of

the bearing indicator. Whenever there is a question as to the reliability of the NDB signal, the pilot should switch to another form of navigation. There are some potential problems of which the pilot should be aware such as, RF

interference from other NOB's, skywave interference (paragraph 25), and adverse

~,7eather and precipitation static (p-static). Adverse 1';1eather and p-static can affect the reception of NDB signals. This is caused primarily by thunderstorms; frictional charging from neutral snow, ice, dust, or particles in the atmosphere; and engine charging.. The duration of these effects can be momentary or they can last for the duration of the flight.

40.-59. RESERVED.

Chap 2 Page 10 ( thru 16) Par 39

CHAPTER 3. OPERATIONAL CHARACTERISTICS OF NDB GROUND STATIONS

CHAPTER 3. OPERATIONAL CHARACTERISTICS OF NDB GROUND STATIONS

60. INTRODUCTION. This chapter identifies signal characteristics and tolerances of the NDB ground station. This chapter represents performance that shall be provided throughout the operational service volume.

61. EMISSION CHARACTERISTICS. The mean power of any unwanted emissions supplied to the antenna transmission line, as compared with the mean power of the fundamental, shall be in accordance with the following:

a. On any frequency removed from the assigned frequency by more than 100 percent, up to and including 150 percent of the authorized bandwidth, at least 25 dB attenuation.

b. On any frequency removed from the assigned frequency by more than 150 percent, and up to and including 300 percent of the authorized bandwidth, at least 35 dB attenuation.

c. On any frequency removed from the assigned frequency by more than 300 percent of the authorized bandwidth~ for transmitters with mean power of 5 kilowatts or greater, at least 80 dB attenuation; and for transmitters with mean power less than 5 kilowatts, at least 43 plus 10 log10 (mean power of

the fundamental in watts) dB attenuation; i.e., 50 microwatts absolute level.

62. FREQUENCY TOLERANCE. The frequency tolerance of the NDB carrier shall comply with the following:

a. The RF carrier of all stations shall be within 0.01 percent of the assigned frequency.

b. With dual carrier NOB's, the requirements of this paragraph refer to the continuous carrier as opposed to the keyed carrier that provides the station identification.

63. FIELD STRENGTH.

a. Minimum Field Strength. Throughout the operational coverage volume, the minimum field strength shall not be less than 50 microvolts per meter (uv/m), which is the minimum value allowed at the alarm point. This is equivalent to 70 uv/m at peak power. (50 uv/m = 34 dBuv/m; 70 uv/m = 37 dBuv/m). dBuv/m are dB's with respect to one microvolt.

b. Flight Inspection Guidance. Minimum field strength settings will be based on flight inspection guidance. Correlation of flight inspection results will be made with the measurements of antenna current and impedance made by the maintenance technician during routine checks of the facility. Also, the selection of airborne locations and times that the field strength is measured is important in order to avoid abnormal results for the locality concerned; locations on air routes in the area around the beacon are operationally most significant.

Chap 3 Par 60 Page 17

5740.6 12/30/87

64. POWER LIMITATIONS. NDB radiated power shall not exceed by more than 2 dB that power which is necessary to provide a field strength of 70 uv/m, at peak power, throughout the operational service volume (see paragraph 63a).

65. SINGLE CARRIER NDB'S. A "single carrier" NDB is a double sideband sys tern. It r ad ia tes a continuous wave ( C\V) carrier on the assigned frequency. The identification signal is provided by keyed AM of the carrier frequency. The emission designator is 2K04A2A for a single carrier NDB with 1020 Hz modulation. The emission designator is 800HA2A for a single carrier NDB with 400 Hz modulation.

56. DUAL CARRIER NDB'S. A "dual carrier" NDB is a single sideband system (full carrier). It radiates a CW carrier on the assigned frequency. The identification signal is provided by on/off keying of a second carrier. This second carrier is transmitted at a frequency equal to the carrier frequency plus the frequency of the modulation tone. For example, at a carrjer frequency of 200kHz, the second carrier would be approximately 200.4 kHz (400Hz

identification) or 201.02 kHz (1020Hz identification). The emission designator is 1Kl2XXA for a dual carrier NOB with 1020 Hz modulation. The emission designator is SOOHXXA for a dual carrier NDB with ~00 Hz modulation.

67. IDENTIFICATION CODE MODULATIONS. The characteristics of the identification code shall conform to the following:

a. Modulation Frequency. The modulation frequency shall be either 400 +25Hz or 1020 +50 Hz.

b. Depth of Modulation. The depth of modulation of the carrier of an NDB should be as great as pqssible. Ninety-five percent modulation, as measured at the transmitter, should be a goal. This goal is dependent upon the antenna systems frequency bandwidth, frequency of the modulation signal, and the condition of the antenna. ~ith these constraints conSidered, the modulation level should be as great as practical without distorting the navigation or identification signal.

68. MONITORING. The radiated signal shall be monitored and removed from service upon recognition of unsafe operations.

69. GROUMDING. Frequency planning is done on the assumption that the field strength and the equivalent isotropic radiated power (•EIRP) will be maintained within the proper tolerances. If the grounding resistance is high (due to insufficient grounding), the radiation efficiency will be lower and the EIRP will have an increased sensitivity to changes in climatic conditions and other

factors. Consequently, in all cases, the grounding system should be the best possible, taking into account local circumstances.

70.-89. RESERVED.

Chap 3 Page 18 (thru 22) Par 64

CHAPTER 4. OPERATIONAL CHARACTERISTICS FOR ADF COMPONENTS

CHAPTER 4. OPERATIONAL CHARACTERISTICS FOR ADF COMPONENTS

90. INTRODUCTION. This chapter specifies the functional capability and performance characteristics required of the ADF component. The term "component" describes the complete aircraft installation. This includes the antenna and its transmission line, the receiver, electrical power source(s),

identification signal reproduction devices, and the bearing indicator~ Airborne components used in IFR operations must meet all Federal Aviation

Regulation requirements. For non-IFR operations, the requirements are limited to those of paragraphs 91 through 96. Components should be capable of performing as specified throughout the operational service volume. The applicable performance requirements should be met when the ground stations are operating in accordance with this order.

91. RECEIVER SENSITIVITY. Based on the field strength specified in paragraph 63, the airborne component shall provide the sensitivity necessary to display the bearing information with the accuracy specified. Clear and distinct reproduction of the identification signal shall be provided in the mode used for navigation. Greater sensitivity is not recommended. Excessive sensitivity makes the receiver unnecessarily susceptible to electromagnetic interference. It also encourages use of the NDB's beyond their operational service volume, where the airspace is not flight inspected and where frequency

protection is not guaranteed.

92. RECEIVER SELECTIVITY. The selectivity of the airborne component shall be sufficient to assure adequate rejection of undesired' signals. Currently, the frequency assignment process provides protection to airborne components that meet or exceed the selectivity of figure 4-1. Future airborne components shall be designed to meet the improved selectivity of figure 4-2.

FIGURE 4-1. CURRENT ADF RECEIVER SELECTIVITY

FIGURE 4-1. CURRENT ADF RECEIVER SELECTIVITY

Frequency One-Signal Two-Signal Difference Se lee t i vi ty Selectivity

0 kHz 0 dB +12 dB +1 kHz 0 dB +11 dB +2 kHz 3 dB + 7 dB +3 kHz -15 dB - 5 dB +4 kHz -29 dB -19 dB +5 kHz -42 dB -32 dB +6 kHz Less than -48 dB Less than -38 dB

NOTE: Two-signal selectivity defines the minimum desired to undesired signal ratio (D/U ratio) for which an ADF shall be able to provide satisfactory navigation information.

Chap 4­ Par 90 Page 23

6 7 40. 6 12/30/87

FIGURE 4-2. FUTURE AUF RECEIVER SELECTIVITY

FIGURE 4-2. FUTURE AUF RECEIVER SELECTIVITY

Frequency One-Signal Two-Signal Difference Selectivity Selectivity

0 kHz 0 dB +12 dB +1 kHz 0 dB +10 dB +1.5 kHz -6 dB + 4 dB +2 kHz -12 dB - 2 dB +3 kHz -27 dB -17 dB -H kHz -42 dB -32 dB +s kHz -57 dB -47 dB +6 kHz -72 dB -62 dB +7 kHz Less Than -80 dB Less Than -70 dB

93. STATION IDENTIFICATION. In the navigation mode, the airborne component shall provide the pilot with positive identification of the ground component.

94. BEARING INFORMATION. The airborne component shall display, >nan

una~biguous manner, the direction of arrival of the radio signal to which the receiver is tuned.

95. BEARING ACCURACY. The indicated bearing shall not differ from the direction of arrival of the radio signal to which the airborne component is

tuned by more than 3 degrees. This shall apply at all bearing pos~t~ons for tuned frequencies in the 190-535 kHz range. (Also see appendix 2).

96.. RADIATION. Radiation from airborne components shall not resul_t ~n degradation of .operational use to other sys tern users.

37. DEVELOPMENT OF FLAG AND WARNING FUNCTIONS. With today's technology, flag and warning functions can be added easily to the ADF receiver. Several receiver types have been marketed with this capability.

Chap 4 Page 24 Par 92

12/30/87

ADF

AGL

AM

AWOS

COMLO

cw

dB

dBuv/m

DME

D/U Ratio

EIRP

FAA

FM

ft

Hz

ICAO

IFR

ILS

kHz

km

LF

WM

LMM

6740.6 Appendix 1

PPENDIX 1. DEFINITIONS AND ACRONYMS

PPENDIX 1. DEFINITIONS AND ACRONYMS

utomatic Direction Finder

bove Ground Level

mplitude Modulation

utomated Weather Observing System

ompass Locator

ontinuous Wave

ecibels

ecibels with respect to one microvolt

istance Measuring Equipment

esired to Undesired Signal Ratio

quivalent Isotropic Radiated Power

A

A

A

A

A

C

C

D

D

D

D

E

Federal Aviation Administration

Frequency Modulation

Feet

Hertz

International Civil Aviation Organization

Instrument Flight Rules

Instrument Landing System

Kilohertz

Kilometer

Low Frequency

Locator, Outer Marker

Locator, Middle Marker

6740.6 Appendix

m

MF

MSL

NAS

NAVAID

NDB

nmi

NOTAM

p-static

RF

RSS

(S+N/N)

TACAN

TIS

uv/m

VFR

VOR

12/30/87

Me.ter

Medium Frequency

Mean Sea Level

National Airspace System

Navigation Aid

Nondirectional Beacon

Nautical Mile

Notice to Airmen

Precipitation Static

Radiofrequency

Root-Sum-Square

Signal Plus Noise-to-Noise Ratio

Tactical Air Navigation

Traveler's Information Service

Microvolt Per Meter

Visual Flight Rules

Very High Freq._uency Omnidirectional Radio Range

12/30/87 6740.6 Appendix 2

APPENDIX 2. SYSTEM BEARING ACCURACY

APPENDIX 2. SYSTEM BEARING ACCURACY

l. SYSTEM ACCURACY. The accuracies described and quantified in paragraph 2 represent the normal error budget for an NDB/ADF System that includes basic avionics with analog indicators, a typical NDB ground station and an environment that does not include excessive environmental errors. Margin for pilot-induced flight technical error is also included.

2. COMBINED ERROR COMPONENT DEFINITION. The error terms are defined as follows:

a. Environmental Error (Ee). Environmental error is the error attributable to such factors as irregular terrain (mountain ridges, sharp

dis~ontinuities in ~rounci conductivity, etc.) and atmospheric noise.

b. ADF Receiver Error (Ea) .. ADF receiver error is that error attributable to the inability of the airborne equipment to determine correctly

the direction of signal arrival relative to the aircraft heading. This element embraces all factors in the ADF receiver which intr0duce errors in the information presented to the pilot.

c. Instrumentation Error (Ei). Instrumentation error is that error attributable to the inability of the airborne equipment to display correctly

the bearing as determined by the ADF receiver.

d. Quadrantal Error (Eq). Quadrantal error is the angular error of a measured bea~ing caused by disturbances due to the characteristics of the

aircraft.

e. Tilt Error (Et)? Tilt error is the error which occurs as a function of the angle that an ·aircraft is banked during flight.

f. Flight Technical Error (Ef). Flight technical error refers to the accuracy with which the pilot controls the aircraft. It is measured by user's success in causing the indicated aircraft position to match the indicated command for desired position~ It does not include procedural blunders.

g. Combined Error (Es). Combined error is the total system error. It takes into account not only the environmental error but also all of the various types of errors attributable to the airborne equipment, the flight technical error, and the quadrantal error.

3. AIRBORNE BEARING ERROR DEFINITION. The term "airborne bearing error" will be considered to include airborne component error, instrumentation error, and quadrantal error.

6740.6 12/30/87 A.ppend ix 2

~. ERROR COMBINATION. Based on the assumptions that the variable errors from tne 'larious sources are normally distributed and independent, they may oe

~omoined in Root-Sum-Squares (RSS) fashion. Thus, the static error standard ieviations obtained Erom tne various contributing sources may be combined

·~:':JL!~trically rather than arithmetically by taking the square root of the sum c·: ::~1.eir squares.

a. Environmental Error (Ee). This component of error is basically uucontrollable. The FA~'s only recourse is to flight check the faciiitie~ and to ~estrict them by NOTAM in any airspace where the combined error is

un~cceptable. tf tne combined error is unacceptable over an appreciable po:ci::ion of th.e service volume, it may be appropriate not to commission the

·:).. ADF Receiver Error (Ea). This component is estimated to be +3 degrees.

c.. Instrumentation Error (Ei). "i:t\is component is estimated to be +2 rl:-:csrees.

d~ Quadrantal Error (Eq). ~fter compensation, this component is

estir1~ated to be .:!:.,5 ciegrees~

~. Tilt Error (Et). Tilt error is a function of the banKing angle of the aircr:aft. Tilt error is not operationally significant.

f~ Flignt Technical Error (Ef). This component is estimated to be +3 d.·-:;rees. Although this error may not be completely independent of other errc·o, independence is assumed in this analysis.

~· Combined Error Determination. Figure 1 presents the RSS method for com. ':!ing-the preV"iously mentioned errors. Based on this determination, the "var :.able" Environmental Error is fixed to a limit of +7.28 degrees by tne use oE Lt:c other error values as fixed max.imum limits.

FIGURE 1. COMBINED ERROR DETERMINATION

FIGURE 1. COMBINED ERROR DETERMINATION

~- .-,·..,.iron:nental Error ( Ee): Variable

.11.:J'l Receiver Error ( Ea): +3 Degrees '"'.Strumentation Error ( E i): +2 Degrees !odrantal Ercor (Eq): +5 Degrees

;_ •i.ght rechnica 1 Error ( E f): +3 Degrees

·>,mt>ined Error: (Ee2 + Ea2 + Ei2 + Eq2 + Ef2)1/2 = (Ee2 + 9 + 4 + 25 + 9)1/2

(Ee2 + 47)1/2 Combined error shall be within :!:_ 10 degrees.

12/30/87 6740.6 Appendix 2

5. LIMITATIONS. The accuracies described in this appendix are applicable to the 190-535 kHz frequency range. The frequencies 435 kHz to 510 kHz are not available for NDB assignment.

12/30/87 6740.6 Appendix 3

APPENDIX 3. NOB FREQUENCIES

APPENDIX 3. NOB FREQUENCIES

1~ AERONAUTICAL RADIONAVIGATION~ In the United States, NOB's operate in a band of the RF spectrum allocated, in parts, to the aeronautical radionavigation service. The FAA, in accordance with National and International agreements, allocates frequencies for NOB use from this band. These

r~strictions, as listed under Remarks~ and the frequency band they apply to are presented as follows:

Frequency (kHz) Remarks 190 200 No voice transmissions permitted.

200-275 Voice transmissions may be permitted.

275-285 Maritime radionavigation is allowed on a secondary basis only. Voice transmissions may be permitted.

285-325 Aeronautical radionavigation allowed on a secondary basis only~ No voice transmissions permitted.

325-335 Maritime radionavigation allowed on a secondary basis. Voice transmissions may be permitted.

335-415 Voice transmissions may be permitted.

415-435 Shared with the Maritime Mobile Service. No voice transmissions permitted.

435-495 Not available for NOB use.

495-505 Not available for NDB use. International Distress Frequency band.

505-510 Not available for NDB use.

510-525 Shared with Maritime Mobile Service. No voice transmissions permitted.

525-535 Shared with the Traveler's Information Service, 530 kHz. No voice transmissions permitted.

NOTE: All voice transmissions~are on a secondary basis; i.e., navigation takes precedence.

Page l