Radar Vectors
FAA Order Current Issued Nov 17, 2005 AJW-1C 473 pages Copy saved Nov 18, 2026

Order 6050.32B Spectrum Management Regulations and Procedures Manual

Official source ↗ Open PDF

Text read by OCR from a scanned file (9 of 473 pages). Check the original, as some words may be misread.

6050_32B.pdf › 01_Cover_Page_6050.32B_111705.pdf

6050.32B ORDER

SPECTRUM MANAGEMENT REGULATIONS

AND PROCEDURES MANUAL

November 17, 2005

DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION

Distribution: A-WYZ-1; A-X(AF/AT)-2; A-FOF-O (SUPV)

Initiated By: Tech Ops ATC Spectrum Engineering Services (ASR-1)

CHANGE U.S. DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION 6050.32B ORDER

6050_32B_CHG_3 › 6050.32B_CHG3_Final_6-11-19 Cover JP Signature Page from Website

CHG 3 Effective Date: 06/11/2019

SUBJ: Spectrum Management Regulations and Procedures Manual

1. Purpose. The current Standard Service Volume (SSV) classes for the VOR/DME/TACAN systems are being augmented with new geometrically larger SSVs to support Performance-Based Navigation.

The purpose of this change is to update the Frequency Protected Service Volume (FPSV) dimensions in FAA Order 6050.32B to accommodate the new SSVs.

2. Who this Change Affects. This change is prepared for all FAA personnel, contractors and staff who utilize and employ FAA Order 6050.32B for spectrum engineering and analysis impacting aviation.

3. Where can I find This Order. You can find this order at www.faa.gov. Click on "Regulations & Policies" and then select "Orders & Notices." Or simply visit https://www.faa.gov/regulations policies/orders notices/.

4. Disposition of Transmittal Paragraph. The transmittal paragraph is for introduction and concept understanding only. All necessary and pertinent documentation has been elsewhere provided for the formal upates.

PAGE CHANGE CONTROL CHART

Remove Pages Dated Insert Pages Dated Table of Contents Table of Contents Page ix and x 11/17/05 Page ix and x 06/11/19

Base Document Base Document Page 91 (thru 94) 11/17/05 Page 91 (thru 95) 06/11/19 APPENDIX 3 APPENDIX 3 Page 7 thru 10 11/17/05 Page 7, 8, 8a, 9, 10 06/11/19

Vice President, Technical Opefations Services Jefey.lanty Plant

Distribution: Electronic Initiated By: AJW-1C

6050_32B_CHG_3 › Signed_Order_6050.32B

CHANGE U.S. DEPARTMENT OF TRANSPORTATION 6050.32B FEDERAL AVIATION ADMINISTRATION CHG 2

11/12/2008

SUBJ:SPECTRUM MANAGEMENT REGULATIONS AND PROCEDURES MANUAL

1. Purpose.Correct the identification of frequency bands which require a proponent building or modifying a facility to file a notice under Federal Air Regulation (FAR) Part 77, to ensure there are no obstacles or radio transmission hazards to aviation.

2. Audience. FAA spectrum management officers.

3. Where can I Find This Order. You can find this order on the Directives Management System (DMS) website: https://employees.faa.gov/tools_ resources/orders notices/.

4. Explanation of Changes. In Chapter 8 (Airspace Evaluation), Paragraph 801c, sub-item (1), a number of frequencybands have been eliminated, thus correcting the information provided in FAA Order 6050.32B and making the information consistent with the recent revision of FAR Part 77.

There will be no air traffic system functional or operational changes resulting from this action.

While the changes only occur on Page 71, Page 72 is also included in the change, since these two pages (71 and 72) are printed back-to-back on the same page.

5.Disposition of Transmittal.Retain this transmittal.

PAGE CONTROL CHART

Remove Pages Dated Insert Pages Dated 71 11/17/05 71 11/12/08 11/17/05 72 11/17/05

Steve Zaidman Vice President, Technical Operations Services

Distribution: A-WYZ-1; A-X(AF/AT)-2; Initiated By:AJW-63 A-FOF-O (SUPV)

6050_32B_CHG_3 › 6050_32_B_Chg_1

CHANGE U.S. DEPARTMENT OF TRANSPORTATION 6050.32B FEDERAL AVIATION ADMINISTRATION CHG 1 National Policy

5/15/2008

SUBJ: SPECTRUM MANAGEMENT REGULATIONS AND PROCEDURES MANUAL

1. Purpose.Modify the usage designations of 121.5 and 123.45 MHz to make them consistent with International Civil Aviation Organization (ICAO) standards.

2. Audience. FAA spectrum management officers.

3. Where Can I Find This Order. You can find this order on the Directives Management System (DMS) website: https://employees.faa.gov/tools resources/orders notices/.

4. Explanation of Changes. Section 4.1.3.2.1 of ICAO Annex 10, Volume V designates the frequency 123.45 MH for air-to-air communications to enable aircraft engaged in flights over remote and oceanic areas out of range of VHF ground stations to exchange necessary operational information and to facilitate the resolution of operational problems. To include this information in 6050.32B, two changes have been made: (1) a new paragraph 908 (Special Use of 123.45 MHz) has been added to Chapter 9 (VHF/UHF Air/Ground Communications Frequency Engineering), Page 86, and (2) a note has been added to the frequency block 123.325- 123.475 MHz on Page 1 of Appendix 2 (Technical Data for VHF/UHF Communications Frequency Engineering), Figure 1 (VHF Allocations – 118-137 MHz).(It should be noted that within the United States, including Alaska, Hawaii and its possessions, the frequency 123.45 MHz is designated for non-government flight test operations.)

In addition, in 6050.32B, also in Figure 1 of Appendix 2, the functional designation of 121.5MHz was wrongly stated as “Emergency Search and Rescue". This usage designation for 121.5 MHz has been changed to "Emergency Frequency", which reflects its long-term usage, and makes the designation fully consistent with Section 4.1.1.1 of ICAO Annex 10, Volume V.

There will be no air traffic control system functional or operational changes resulting from these actions.

Since 6050.32B is printed on both the front and back sides of each page, the change on Page 86 to Chapter 9 will also require the replacement of Page 85, even though there is no change to Page 85. Likewise, the changes to Appendix 2, Page 1, will also require the replacement of Page 2to that appendix.

Distribution:A-WYZ-1; A-X(AF/AT)-2; Initiated By:AJW-63 A-FOF-O(SUPV)

5/15/2008

6050.32BCHG1

5. Disposition of Transmittal. Retain this transmittal.

PAGE CONTROL CHART

Remove Pages 85 86 1 (Appendix 2) 2 (Appendix 2)

Steve Zaidman

Dated 11/17/05 11/17/05 11/17/05 11/17/05

Insert Pages 85 86 1 (Appendix 2) 2 (Appendix 2)

Dated 11/17/05 5/15/2008 5/15/2008 11/17/05

U.S. DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION ORDER

6050.32B

Effective Date: 11/17/05

SUBJ: Spectrum Management Regulations and Procedures Manual

The radio spectrum is both a precious and limited National resource. Within the Federal Aviation Administration (FAA), Technical Operations ATC Spectrum Engineering Services is the sole authority for the spectrum allocation for new systems during equipment research and design as well as the FAA's single point-of-contact for coordination of operating frequencies with other Federal agencies and civil organizations.

6050_32_B_Chg_1 › 02_Foreward_6050.32B_111705.pdf

Each country exercises its own sovereign rights in its use of the spectrum. Because radio transmission cannot be limited to a national border, international agreements and management practices are necessary. It is of utmost importance that we manage the radio spectrum efficiently and effectively in order to support air traffic requirements of our National Airspace System (NAS).

This order on spectrum policy and management is for the purpose of presenting spectrum engineering policy, guidance, and criteria to spectrum engineers. It is an update of technical information from many sources and offers the spectrum engineer a widely based tool necessary to manage the radio spectrum used to support the NAS.

Dissemination of this order throughout the Agency and to interfacing organizations will provide various offices a single source of knowledge of the functions and responsibilities of international and national regulation of the radio spectrum.

The magnitude of spectrum utilization in terms of amount and variety of equipment, power, emission characteristics, time-on-the-air, and geographical coverage is rapidly increasing and will continue to do so. Congestion, especially in the navigational aids and air/ground communications frequency bands, is a persistent problem that can lead to interference and, thus, the limiting or denial of required services. Conflicts in communications, radar, and navigational aids usually can be resolved; but resolution often requires time, money, and modification of service requirements. In peacetime, this may be simply annoying. In a national emergency, it could be devastating.

A communications, navigational aid, or radar facility out-of-service for interference is just as useless as one out for technical defects. Efficient, effective, and informed management of the spectrum is a prerequisite to the solution of congestion within FAA's purview. This can only be accomplished by professiopalspectrum engineering coupled with a dedicated staff of spectrum engineers and managers with appropriate authdrity to carry out their task.

Steve Zaidman Vice President/Technical Operations Services

Distribution: A-WYZ-1; A-X(AF/AT)-2; Initiated By: Tech Ops ATC Spectrum A-FOF-O (SUPV) Engineering Services (ASR-1)

6050_32_B_Chg_1 › 03_Table_ Cont_6050.32B_111705.pdf

11/17/05 6050.32B

TABLE OF CONTENTS Paragraph … Page CHAPTER 1. GENERAL 1. Purpose … 1 2. Distribution … 1 3. Cancellation … 1 4. Explanation of Changes … 1 5. Forms … 2 6. thru 199. Reserved … 2 CHAPTER 2. THE RADIO FREQUENCY (RF) SPECTRUM 200. RF Spectrum … 7 201. Makeup of the Spectrum … 7 202. Spectrum Limitation Considerations … 7 203. thru 299. Reserved … 9 CHAPTER 3. HISTORY, AUTHORITIES AND RESPONSIBILITIES 300. General Considerations … 17 301. International Organizations … 17 Figure 3-1. Partial Organizational Chart of the ITU … 18 Figure 3-2a. ICAO Assembly Organization Chart … 20 Figure 3-2b. ICAO Secretariat Organization Chart … 20 302. National Organizations - General … 21 Figure 3-3. Federal Communications Commission … 22 Figure 3-4. National Telecommunications and Information Administration … 24 Figure 3-5. Partial Organization Chart of the IRAC … 25 Figure 3-6. AAG Controlled Bands … 26 Figure 3-7. Bands Under Coordination Control of FAA Field Coordinators … 27 Figure 3-8. Technical Operations ATC Spectrum Engineering Services … 28 Figure 3-9. Summary of Frequency Bands Supporting Aviation … 29 303. Technical Operations ATC Spectrum Engineering Services … 30 304. Service Area Frequency Management Office (FMO) … 30 305. thru 399. Reserved … 31 CHAPTER 4. SPECTRUM MANAGEMENT EVALUATION CRITERIA 400. General … 33 401. Criteria … 33 402. Subjects of Evaluation … 33 403. thru 499. Reserved … 35 CHAPTER 5. FREQUENCY COORDINATION 500. General … 41 501. Headquarters … 41 502. Field-Headquarters … 41

Page i

6050.32B Table of Contents - continued 11/17/05

503. Field-External … 41 504. Field-Special … 42 Figure 5-1. Sample Memorandum To Aviation Event Sponsor … 44 505. Field-Internal … 46 506. Documents … 47 507. thru 599. Reserved … 48 CHAPTER 6. TRANSMITTER AUTHORIZATION DOCUMENTS AND CALL LETTER ASSIGNMENTS 600. Purpose … 53 601. Facility Transmitting Authorization Document (FTA) … 53 Figure 6-1. FAA Form 6050-1. Facility Transmitting Authorization (Reduced) … 54 Figure 6-2. TIOA Forms For Mobile/Portable/Handheld Transmitters … 54 602. Requests For Frequency Action … 55 Figure 6-3. Sample of a Typical Service Area Frequency Request Form (Reduced) … 55 603. Call Letter Assignment … 56 604. Land Mobile Call Signs … 56 Figure 6-4. User Organization Identifiers … 57 605. Station Identification Requirements … 57 606. thru 699. Reserved … 57 CHAPTER 7. HIGH FREQUENCY ASSIGNMENT PROCEDURES 700. General … 63 Figure 7-1. Ionospheric Layers Illustrated … 64 701. International HF Requirements … 64 702. National HF Requirements … 65 Figure 7-2. NRCS Frequencies … 65 703. HF Engineering … 66 704. Assigned vs. Window Frequency … 66 705.

Propagation and Circuit Reliability … 66 706. Sunspot Numbers … 66 707. Solar Flare/Storm Reporting Procedures … 67 Figure 7-3. Smoothed Monthly Sunspot Numbers Jan 1749 - Apr 1996 … 67 708. thru 799. Reserved … 67 CHAPTER 8. AIRSPACE EVALUATION 800. General … 71 801. Part 77 … 71 802. Title 49, Section 44718 … 72 803. Intranet Obstruction Evaluation/Airport Airspace Analysis (IOE/AAA) Web-based System 72 804. Washington Headquarters Reviews … 72 805. Electromagnetic Evaluation … 73 806. Airspace Analysis Model (AAM) … 73 807. Determinations … 74 808. Non-Broadcast Evaluations … 74 809. thru 899. Reserved … 76 CHAPTER 9. VHF/UHF AIR/GROUND COMMUNICATIONS FREQUENCY ENGINEERING

Page ii

11/17/05 Table of Contents - continued 6050.32B

900. Purpose … 81 901. Communications Frequency Allocations … 81 902. Basic Principles of Communications Frequency Engineering … 81 903. Special Issues To Be Considered … 82 904. Automatic Terminal Information Service (ATIS) Voice Outlet Assignment Criteria … 82 905. AWOS/ASOS Frequency Assignment Criteria … 83 906. Backup Communications … 84 907. Temporary Assignments … 85 908. thru 999. Reserved … 86 CHAPTER 10. NAVIGATIONAL AID (NAVAID) FREQUENCY ENGINEERING 1000. Purpose … 91 1001. NAVAID Frequency Allocation … 91 Figure 10-1. NAVAID Band Use … 91 1002. Basic Principles of NAVAID Frequency Engineering … 91 1003. NAVAID Frequency Engineering Methods … 92 1004. Equivalent Signal Ratio (ESR) … 92 1005. Expanded Service Volume (ESV) … 92 1006. Special Issues To Be Considered … 92 1007. thru 1099. Reserved … 94 CHAPTER 11. LOW/MEDIUM FREQUENCY (L/MF) GROUND NAVIGATIONAL AIDS 1100. Purpose … 99 1101. General Considerations … 99 1102. Frequency Allocation For L/MF Facilities … 100 Figure 11-1. L/MF NAVAID Frequency Allocations … 101 1103.

Engineering Considerations For L/MF Frequency Selection … 102 Figure 11-2. Estimated Ground Conductivity in the United States … 103 1104. Basic Tools … 104 Figure 11-3. Coverage and Interference Prediction Curves … 105 1105. Engineering Procedures … 106 1106. Practical Example … 107 Figure 11-4. Geographic Separation Example … 107 1107. Airborne Measurements … 108 1108. thru 1199. Reserved … 108 CHAPTER 12. MICROWAVE DATA/COMMUNICATIONS LINKS FREQUENCY ENGINEERING 1200. Purpose … 111 1201. Frequency Bands Available For Radio Links … 111 Figure 12-1. Bands Currently Used by FAA For Radio Links … 111 1202. International Coordination Requirements … 112 1203. Technical Standards For Links … 112 1204. The General Procedure For Microwave Link Intersite Frequency Engineering … 112 Figure 12-2. Typical Parabolic Microwave Antenna Radiation Pattern … 114 Figure 12-3. Power Budget Study For a Microwave Link … 116 1205. Frequency Engineering For the 932-935 and 941-944 MHz Bands … 117 1206. Frequency Engineering For the 1710-1850 MHz Band … 117

Page iii

6050.32B Table of Contents - continued 11/17/05

1207. Frequency Engineering For RCL in the 7125-8500 MHz Band … 118 Figure 12-4. Example of Tests 4 and 5 Prohibited Zones … 119 Figure 12-5. Standard RCL Frequency Family For 7125-8400 MHz … 120 Figure 12-6. Sample of Frequency Selection, Test 4 and 5 … 121 1208. Frequency Engineering For the LDRCL in the 7125-8500 MHz Band … 121 1209. Frequency Engineering For the 14.5000-14.7145 and 15.1365-15.3500 GHz Bands … 122 Figure 12-7. Current TML Channelization Plan … 123 1210. Frequency Engineering for LDRCL For the 21.2-23.6 GHz Band … 124 Figure 12-8. 21.2-23.6 GHz LDRCL Frequency Assignment Plan … 124 1211. Special Path Considerations … 124 Figure 12-9. Space Diversity … 125 Figure 12-10. Frequency Diversity … 125 Figure 12-11. Hybrid Frequency/Space Diversity … 126 1212. Paths With Passive Reflectors … 126 Figure 12-12. Periscope or Top Reflector Antenna System … 127 Figure 12-13. Single Billboard Passive Antenna … 127 Figure 12-14. Double Billboard Passive Antenna … 128 1213. Mapping … 128 1214. thru 1299. Reserved … 128

CHAPTER 13. RADAR AND AIR TRAFFIC CONTROL RADAR BEACON SYSTEM (ATCRBS) FREQUENCY ENGINEERING 1300. Policy … 137 1301. General Assignment Procedures … 138 1302. PRR Assignment of ATCRBS … 139 Figure 13-1. Display Time Exposure For a Radial Flight Showing Ringaround … 140 Figure 13-2. Display View of a Real and a False Target … 141 1303. PRR Assignment Process … 141 Figure 13-3. Radar and Associated Beacon Capabilities … 144 1304. Frequency Assignment Process in the Radar Frequency Bands … 144 Figure 13-4. Radar Frequency-Distance Separation Criteria … 145 1305. Frequency Assignments in the 1215-1390- MHz Band … 145 Figure 13-5. ARSR-1/2 Staggered PRR and PRT Values (High) … 146 Figure 13-6. ARSR-1/2 Staggered PRR and PRT Values (Low) … 147 Figure 13-7. ARSR-3 PRR Capabilities … 149 Figure 13-8. ARSR-3 Average VIP PRTs … 150 Figure 13-9. ARSR-4 Crystal Oscillator, Stabilized Local Oscillator (STALO) and Transmit Frequencies … 151 1306. Frequency Assignment Process in the 2700-3000 MHz Band … 152 Figure 13-10. ASR-7E Primary Radar Frequency Pairs … 153 Figure 13-11. ASR-7 and Associated Beacon Staggered PRR and PRT … 154 Figure 13-12. ASR-8 and Associated Beacon Staggered PRR and PRT … 155 Figure 13-13. Typical ASR-8 Receiver Susceptibility Pass Band … 156 Figure 13-14. ASR-9 Radar and Beacon PRRs … 157 1307. Frequency Assignments in the 5600-5650 MHz Band … 158 1308. Frequency Assignments in the 9000-9200 MHz Band … 158 1309. Frequency Assignments in the 15.7-16.2 GHz Band … 159 1310. thru 1399. Reserved … 159 CHAPTER 14. RADIO FREQUENCY INTERFERENCE

Page iv

11/17/05 Table of Contents - continued 6050.32B

1400. Interference Problems … 167 1401. Interference Reporting … 167 1402. Administrative Procedures … 168 1403. Internal Procedures … 170 1404. Interference Locating Equipment … 170 1405. Interference Locating Techniques … 172 Figure 14-1. Image Frequency Relationships … 175 1406. Direction Finding (Below 1000 MHz) … 178 1407. Direction Finding (Above 1000 MHz) … 180 Figure 14-2. Radar Interference DF Example … 181 1408. "Running Rabbit" Interference … 181 Figure 14-3. Running Rabbits Patterns … 182 1409. Electronic Attack (EA) … 183 1410. Power Line Interference … 183 1411. Digital Radio Systems … 184 1412. ELT Problems … 184 1413. Records of Unusual Previous Cases … 184 1414. thru 1499. Reserved … 184 CHAPTER 15. RADIO FREQUENCY INTERFERENCE MONITORING VANS (RFI VANS) 1500. Introduction … 189 Figure 15-1. RFIM Functional Block Diagram … 189 1501. Control and Responsibility … 190 1502. RFI Van Use … 190 1503. Instrumentation … 190 1504. RFI Van System Operation … 193 Figure 15-2. MCS Canned Measurements Startup Screen … 193 1505.

Radar and ATCRBS Antenna Pattern Recording … 194 Figure 15-3. Recording Setup and Sample tape … 194 Figure 15-4. Examples of Antenna Patterns On CCSA Printouts … 196 1506. High-Speed Recorder Calibration and Operation … 197 1507. Spectrum Analysis … 198 Figure 15-5. Photo of Spectrum From a Spectrum Analyzer … 198 Figure 15-6. CCSA-Produced Radar Spectrum Plot … 199 Figure 15-7. A DC Bucking Voltage System For X-Y Plotters … 200 Figure 15-8. Sample Spectrum Plot of a Rotating Radar … 202 1508. Frequency Measurements … 202 1509. Off-The-Air PRR Measurement … 203 Figure 15-9. Block Diagram of One Method of Measuring PRR … 204 Figure 15-10. Scope Displays For Correct and Incorrect Measurement … 205 1510. thru 1599. Reserved … 205 CHAPTER 16. IONIZED AND NONIONIZED RADIATION MEASUREMENTS 1600. Purpose … 215 1601. General … 215 Figure 16-1. Process for Obtaining a Radiation Hazard Measurement … 216 1602. Importance of Measurements … 217 1603. FMO Participation Limitation … 217

Page v

6050.32B Table of Contents - continued 11/17/05

1604. Importance of Accuracy … 217 1605. Instrument Calibration … 217 1606. Availability … 217 1607. Ramifications … 218 1608. Measurement Philosophy … 218 1609. Measurement Considerations … 218 1610. Measurement Standards and Procedures … 219 1611. Ionized Radiation Measurement Procedures … 220 1612. Non-Ionized Radiation Measurement and Procedures … 221 Figure 16-2. Radars Used by FAA With Power Densities >MPE … 224 1613. Measurement Considerations and Reference Data … 225 Figure 16-3. Non-Ionizing MPE – Uncontrolled Environment … 226 Figure 16-4. Non-Ionizing MPE – Controlled Environment … 227 Figure 16-5. Ionizing TLV … 228 Figure 16-6a. Letter of Agreement Safety Program Responsibilities … 229 Figure 16-6b. Letter of Agreement Safety Program Responsibilities … 230 Figure 16-6c. Letter of Agreement Safety Program Responsibilities … 231 Figure 16-6d. Letter of Agreement Safety Program Responsibilities … 232 1614. thru 1699. Reserved … 232 CHAPTER 17. LAND MOBILE AND OTHER FM COMMUNICATIONS SYSTEMS FREQUENCY ENGINEERING 1700. General … 235 1701. Frequency Engineering … 235 1702.

Systems Basics … 235 1703. C3/NRCS … 235 Figure 17-1. C3/NRCS Communications Frequency Plan … 235 Figure 17-2. Example of a Repeater/Base/Portable/Mobile FM System … 236 1704. RF Voice/Data Link Systems … 237 1705. Miscellaneous Radio Links … 237 1706. Narrow Band Requirements … 238 1707. thru 1799. Reserved … 238 CHAPTER 18. ELECTRONIC ATTACK (EA) EVALUATIONS 1800. Purpose … 241 1801. Definitions … 241 1802. Applicable Regulations and Documents … 242 1803. Responsibilities … 242 1804. Analysis of EA Request … 243 1805. Conclusions … 244 1806. Operational Band and Channel Codes … 244 Figure 18-1. Frequency Band Designations … 245 1807. Frequency Band Correlation … 246 Figure 18-2. Frequency Band Correlation … 246 1808. EA Coordination Requirements by Frequency Band … 246 Figure 18-3a. Coordination Level Required by Channel and Frequency … 247 Figure 18-3b. Coordination Level Required by Channel and Frequency … 248 Figure 18-3c. Coordination Level Required by Channel and Frequency … 249

Page vi

11/17/05 Table of Contents - continued 6050.32B

Figure 18-3d. Coordination Level Required by Channel and Frequency … 250 Figure 18-3e. Coordination Level Required by Channel and Frequency … 251 Figure 18-3f. Coordination Level Required by Channel and Frequency … 252 Figure 18-3g. Coordination Level Required by Channel and Frequency … 253 Figure 18-3h. Coordination Level Required by Channel and Frequency … 254 Figure 18-3i. Coordination Level Required by Channel and Frequency … 255 1809. thru 1899. Reserved … 255 CHAPTER 19. AUTOMATED ENGINEERING 1900. Purpose … 261 1901. Automated Frequency Manager (AFM) … 261 1902. AFM Agenda System … 261 1903. Airspace Analysis Model (AAM) … 261 1904. RFI and RADHAZ Data Base … 261 1905. Expanded Service Volume (ESV) Management System (ESVMS) … 261 1906. Radio Coverage Analysis System (RCAS) … 261 1907. Overview of the AFM … 262 1908. AFM Agenda System … 263 1909. Airspace Analysis Model (AAM) … 264 1910. RFI and RADHAZ Support … 265 1911. ESV … 267 1912. thru 1999. Reserved … 267 APPENDIX 1. AIRSPACE EVALUATION SECTION 1. BACKGROUND AND PROCEDURES 1. Introduction … 1 2. Background … 1 3.

FM Broadcast Tolerances … 1 Figure 1. FM Channels and Center Frequencies … 2 Figure 2. Spurious Emission Level of an FM Broadcast Transmitter on 107.9 MHz … 4 4. TV Broadcast Tolerances … 4 5. AM and Other Non-Broadcast Station Standards … 5 6. Standard FPSVs For FAA Facilities … 5 Figure 3. TV Channels and Associated Frequencies … 6 Figure 4. Idealized Standard TV Channel Spectrum … 7 7. Evaluation Procedure Outline … 7 8. Data Assembly … 7 Figure 5. Evaluation Procedure Outline Chart … 8 9. Intermod Study … 9 10. Ground Facilities … 9 Figure 6. Typical FAA VHF and UHF RCF Ground Antenna Gain Vs. Frequency Plots … 11 Figure 7. Example of Plot For Calculating Slant Range … 13 11. Airborne Receivers … 13 12. Samples … 14 Figure 8. Relative Gain of Airborne COMM and NAV Antennas … 15 Figure 9a. FAA Form 7460-1, Notice of Proposed Construction or Alteration … 16 Figure 9b. Addenda to FAA Form 74670-1 Notice of Proposed Construction or

Page vii

6050.32B Table of Contents - continued 11/17/05

Alteration … 17 Figures 10. thru 14. Reserved … 17 13. thru 16. Reserved … 17 SECTION 2. ENGINEERING PROCEDURES FOR OE CASES FOR FM BROADCAST AND ILS/VOR 17. Purpose … 23 18. OE Case Evaluation Procedure … 23 Figure 15. Sample OE Case Worksheet For FM … 24 Figure 16. Sample PC CIRCLE Report … 26 Figure 17. Sample GROUND.WK1 Report … 27 19. Example of AAM Program For FM/ILS … 28 Figure 18. AAM Program Sample Search Plot … 29 Figure 19a. AAM Program Sample RFI.PRT Printout … 30 Figure 19b. AAM Program Sample RFI.PRT Printout (continued) … 31 Figure 20. AAM Sample Plot of Predicted RFI - Horizontal - KHTN … 32 Figure 21. AAM Sample Plot of Predicted RFI - Horizontal - PROP … 33 Figure 22. AAM Sample Plot of Predicted RFI - Vertical - KHTN … 34 Figure 23. AAM Sample Plot of Predicted RFI - Vertical - PROP … 35 Figures 24. thru 30. Reserved … 35 20. thru 24. Reserved … 35 SECTION 3. ENGINEERING PROCEDURES FOR OBSTRUCTION EVALUATION (OE) CASES OF NON-FM BROADCAST 25. Status … 41 26. Non-FM BC Study Procedures … 41 27. A Non-FM BC Example … 42 Figure 31.

Sample Non-FM Worksheet … 43 Figure 32. Paragraph 26 a. (1) Example GROUND.WK1 Printout … 44 Figure 33. Paragraph 26 a. (3) Example IM Program Configuration … 45 Figure 34. Paragraph 26 a. (4) Example of IM Program Printout … 45 APPENDIX 2. TECHNICAL DATA FOR VHF/UHF COMMUNICATIONS FREQUENCY ENGINEERING Figure 1. VHF Allocations - 118-137 MHz … 1 1. VHF/UHF Frequency Engineering … 2 2. FPSV … 2 Figure 2. FPSVs … 2 Figure 3. High Altitude Enroute and Local Control FPSVs to Approximate Scale and As Normally Shown Pictorially … 3 Figure 4. Example of En Route Dimensions … 3 Figure 5. Typical Terminal FPSV Dimensions … 4 3. ATC Assignment Criteria … 5 4. RLOS … 5 Figure 6. Comparison of Distance to Horizon From the Same Altitude Between Actual and Hypothetical 4/3 Earth Radius … 6 5. Intersite Frequency Engineering Procedures … 7 Figure 7. Cochannel Configuration For Undesired/Desired Distance Ratio … 7

Page viii

6050_32B_CHG_3 › TOC3-final_ix-x 06-11-2019 (004)

06/11/19 Table of Contents - continued 6050.32B CHG 3

6. Intersite Cochannel Analysis By the Table Method … 8 Figure 8. Mileage Separation Tables For Usual FPSVs … 8 7. Adjacent Channel Considerations … 8 Figure 9. Adjacent Channel Vertical Separation … 9 Figure 10. 1st Adjacent Channel Separation Required … 10 8. Intersite Cochannel Analysis … 10 Figure 11. Cochannel Analysis by Calculation … 11 Figure 12. Comparison of D/U and Distance Between Facilities With One Tailored

Service Volume … 11 9. Cosite Interference Considerations … 11 10. Limits of Coverage Charts … 12 Figure 13. Limits of Coverage - VHF - Antenna Height = 10' … 13 Figure 14. Limits of Coverage - VHF - Antenna Height = 25' … 14 Figure 15. Limits of Coverage - VHF - Antenna Height = 50' … 15 Figure 16. Limits of Coverage - VHF - Antenna Height = 75' … 16 Figure 17. Limits of Coverage - VHF - Antenna Height = 100' … 17 Figure 18. Limits of Coverage - VHF - Antenna Height = 150' … 18 Figure 19. Limits of Coverage - UHF - Antenna Height = 10' … 19 Figure 20. Limits of Coverage - UHF - Antenna Height = 20' … 20 Figure 21. Limits of Coverage - UHF - Antenna Height = 30' … 21 Figure 22. Limits of Coverage - UHF - Antenna Height = 40' … 22 Figure 23. Limits of Coverage - UHF - Antenna Height = 50' … 23 Figure 24. Limits of Coverage - UHF - Antenna Height = 75' … 24

APPENDIX 3. NAVAID FREQUENCY ENGINEERING DATA AND PROCEDURES

SECTION 1. FREQUENCY/CHANNELIZATION CHART

Figure 1a. Channel and Frequency Pairing With DME Pulse Time/Codes … 1 Figure 1b. Channel and Frequency Pairing With DME Pulse Time/Codes (cont'd) … 2 Figure 1c. Channel and Frequency Pairing With DME Pulse Time/Codes (cont'd) … 3 Figure 1d. Channel and Frequency Pairing With DME Pulse Time/Codes (cont'd) … 4 Figure 1e. Channel and Frequency Pairing With DME Pulse Time/Codes (cont'd) … 5 Figure 1f. Channel and Frequency Pairing With DME Pulse Time/Codes (cont'd) … 6

SECTION 2. VOR AND DME/TACAN FREQUENCY ENGINEERING

1. Frequency Engineering … 7 Figure 2a. Standard Service Volumes (SSV) … 8 Figure 2b. VOR Service Volumes … 8a Figure 2c. DME Service Volumes … 8a 2. Frequency Engineering Procedures … 9 3. Intersite Analysis By the Table Method For VOR … 9 4. Intersite Analysis By the Table Method For DME/TACAN … 9 5. DME/TACAN Required Separation … 9 6. Use of the Larger Separation Requirement … 10 7. Permissible Use of Tables … 10 Figure 3. VOR/VOR Cochannel Separations … 10

Page ix

6050.32B CHG 3 Table of Contents - continued 06/11/19

Figure 4. VOR/VOR Interim 1st Adjacent Channel -50 kHz- Separations … 11 Figure 5. VOR/VOR Final 1st Adjacent Channel -50 kHz- Separations … 11 Figure 6. VOR/VOR 2nd Adjacent Channel -100 kHz- Separations … 12 Figure 7. VOR/LOC Interim 1st Adjacent Channel -50 kHz- separations … 12 Figure 8. VOR/LOC Final 1st Adjacent Channel -50 kHz- Separations … 13 Figure 9. DME/TACAN Cochannel Separations … 13 Figure 10. DME/TACAN 1st Adjacent Channel Separations … 14 8. Intersite Analysis By the Calculation Method … 14 Figure 11. VOR, DME and TACAN Antenna Gain Figures … 15 9. Sample of Cochannel Intersite Analysis By the Calculation Method … 16 Figure 12. VORTAC Cochannel Intersite Analysis Plot … 16 10. Intersite Analysis of Adjacent Channels … 17 Figure 13. VORTAC 2nd Adjacent Channel Intersite Analysis … 17 11. Differences In Site Elevation … 18 12. thru 13. Reserved … 18 Figure 14. VOR Facility Separation Curves For ESR = +14 dB … 19 Figure 15. VOR Facility Separation Curves For ESR = +17 dB … 20 Figure 16. VOR Facility Separation Curves For ESR = +20 dB … 21 Figure 17.

VOR Facility Separation Curves For ESR = +23 dB … 22 Figure 18. VOR Facility Separation Curves For ESR = +26 dB … 23 Figure 19. VOR Facility Separation Curves For ESR = +29 dB … 24 Figure 20. VOR Facility Separation Curves For ESR = +32 dB … 25 Figure 21. ESR Ratio - VOR/VOR @ 1,000' … 26 Figure 22. ESR Ratio - VOR/VOR @ 5,000' … 27 Figure 23. ESR Ratio - VOR/VOR @ 10,000' … 28 Figure 24. ESR Ratio - VOR/VOR @ 15,000' … 29 Figure 25. ESR Ratio - VOR/VOR @ 18,000' … 30 Figure 26. ESR Ratio - VOR/VOR @ 20,000' … 31 Figure 27. ESR Ratio - VOR/VOR @ 30.000' … 32 Figure 28. ESR Ratio - VOR/VOR @ 40,000' … 33 Figure 29. ESR Ratio - VOR/VOR @ 50,000' … 34 Figure 30. ESR Ratio - VOR/LOC. VOR Is Desired @ 1,000' … 35 Figure 31. ESR Ratio - VOR/LOC. VOR Is Desired @ 5,000' … 36 Figure 32. ESR Ratio - VOR/LOC. VOR Is Desired @ 10,000' … 37 Figure 33. ESR Ratio - VOR/LOC. VOR Is Desired @ 15,000' … 38 Figure 34. ESR Ratio - VOR/LOC. VOR Is Desired @ 18,000' … 39 Figure 35. ESR Ratio - VOR/LOC. VOR Is Desired @ 20,000' … 40 Figure 36. ESR Ratio - VOR/LOC. VOR Is Desired @ 30,000' … 41 Figure 37.

ESR Ratio - VOR/LOC. VOR Is Desired @ 40,000' … 42 Figure 38. ESR Ratio - VOR/LOC. VOR Is Desired @ 50,000' … 43 Figure 39. DME/TACAN Facility Separation Curves For ESR = +2 dB … 44 Figure 40. DME/TACAN Facility Separation Curves For ESR = +5 dB … 45 Figure 41. DME/TACAN Facility Separation Curves For ESR = +8 dB … 46 Figure 42. DME/TACAN Facility Separation Curves For ESR = +11 dB … 47 Figure 43. DME/TACAN Facility Separation Curves For ESR = +14 dB … 48 Figure 44. DME/TACAN Facility Separation Curves For ESR = +17 dB … 49 Figure 45. DME/TACAN Facility Separation Curves For ESR = +20 dB … 50 Figure 46 ESR Ratio - DME/TACAN to DME/TACAN @ 1,000' … 51 Figure 47. ESR Ratio - DME/TACAN to DME/TACAN @ 18,000' … 52 Figures 48 thru 60. Reserved … 52 Page x

11/17/05 Table of Contents - continued 6050.32B

SECTION 3. ILS AND DME FREQUENCY ENGINEERING 14. Frequency Engineering For ILS and DME … 61 Figure 61. LOC Front Course FPSV … 61 Figure 62. LOC Back Course FPSVs … 62 Figure 63. FPSV For ILS GS … 63 Figure 64. FPSVs For DMEs Associated With ILS … 63 15. Frequency Engineering Procedures … 64 16. Intersite Analysis By the Table Method For ILS LOCs … 65 17. Intersite Analysis By the Table Method For ILS-DME … 65 18. ILS-DME Required Separation … 65 19. Use of The Larger Separation Requirement … 66 20. ILS Associated DME Adjacent Channel Undesired … 66 Figure 65. LOC Separation Distances Defined … 66 Figure 66. LOC/LOC Cochannel Radii Separations … 67 Figure 67. LOC/LOC 1st Adjacent Channel - 50 kHz - Separations - Interim … 67 Figure 68. LOC/LOC 1st Adjacent Channel - 50 kHz - Separations - Final … 68 Figure 69. LOC/VOR 1st Adjacent Channel - 50 kHz - Separations - Interim … 68 Figure 70. LOC/VOR 1st Adjacent Channel - 50 kHz - Separations - Final … 69 Figure 71. LOC/VOR 2nd Adjacent Channel - 100 kHz - Separations … 69 Figure 72. ILS-DME Cochannel Separations … 70 Figure 73.

ILS-DME 1st Adjacent Channel Separations … 70 21. Intersite analysis of ILS by Calculation Method … 71 Figure 74. LOC Antenna Gains and Graph Reference … 72 Figure 75. Critical Point Separation Distance … 73 22. Special Consideration For ILSs on Opposite Ends of a Runway … 73 Figure 76. LOC Intersite Analysis By Calculation … 74 23. LOC Calculation Example … 74 Figure 77. DME and TACAN Antenna Gain Figures … 76 Figure 78. DME Intersite Analysis by Calculation … 76 24 DME Calculation Example … 77 25. ILS Markers … 78 26. thru 30. Reserved … 78 Figure 79. LOC Facility Separation Curves For ESR = -52 dB … 79 Figure 80. LOC Facility Separation Curves For ESR = -49 dB … 80 Figure 81. LOC Facility Separation Curves For ESR = -46 dB … 81 Figure 82. LOC Facility Separation Curves For ESR = -43 dB … 82 Figure 83. LOC Facility Separation Curves For ESR = -40 dB … 83 Figure 84. LOC Facility Separation Curves For ESR = -37 dB … 84 Figure 85. LOC Facility Separation Curves For ESR = -34 dB … 85 Figure 86. LOC Facility Separation Curves For ESR = -31 dB … 86 Figure 87.

LOC Facility Separation Curves For ESR = -28 dB … 87 Figure 88. LOC Facility Separation Curves For ESR = -25 dB … 88 Figure 89. LOC Facility Separation Curves For ESR = -22 dB … 89 Figure 90. LOC Facility Separation Curves For ESR = -19 dB … 90 Figure 91. LOC Facility Separation Curves For ESR = -16 dB … 91 Figure 92. LOC Facility Separation Curves For ESR = -13 dB … 92 Figure 93. LOC Facility Separation Curves For ESR = -10 dB … 93 Figure 94. LOC Facility Separation Curves For ESR = -7 dB … 94 Figure 95. LOC Facility Separation Curves For ESR = -4 dB … 95

Page xi

6050.32B Table of Contents - continued 11/17/05

Figure 96. LOC Facility Separation Curves For ESR = -1 dB … 96 Figure 97. LOC Facility Separation Curves For ESR = +2 dB … 97 Figure 98. LOC Facility Separation Curves For ESR = +5 dB … 98 Figure 99. LOC Facility Separation Curves For ESR = +8 dB … 99 Figure 100. LOC Facility Separation Curves For ESR = +11 dB … 100 Figure 101. LOC Facility Separation Curves For ESR = +14 dB … 101 Figure 102. LOC Facility Separation Curves For ESR = +17 dB … 102 Figure 103. LOC Facility Separation Curves For ESR = +20 dB … 103 Figure 104. LOC Facility Separation Curves For ESR = +23 dB … 104 Figure 105. LOC Facility Separation Curves For ESR = +26 dB … 105 Figure 106. LOC Facility Separation Curves For ESR = +29 dB … 106 Figure 107. LOC Facility Separation Curves For ESR = +32 dB … 107 Figure 108. ESR ratio - LOC/VOR. LOC Is Desired Facility @ 1,000' … 108 Figure 109. ESR ratio - LOC/VOR. LOC Is Desired Facility @ 4,500' … 109 Figure 110. ESR ratio - LOC/VOR. LOC Is Desired Facility @ 6,250' … 110 Figure 111. LOC LPD (14-10) and (20-10) Antenna Radiation Patterns … 111 Figure 112.

LOC V Ring Antenna Radiation Pattern … 112 Figure 113. LOC Travelling Wave - 8 el Antenna Radiation Pattern … 113 Figure 114. LOC Travelling Wave - 14 el Antenna Radiation Pattern … 114 Figure 115. LOC LPD 8 El Antenna Radiation Pattern … 115 Figure 116. LOC LPD 14 el Antenna Radiation Pattern … 116 Figure 117. LOC LPD GRN-29 Antenna Radiation Pattern … 117 Figure 118. LOC Travelling Wave 14/6 Antenna Radiation Pattern … 118 Figure 119. LOC Parabolic Narrow Antenna Radiation Pattern … 119 Figure 120. LOC Parabolic Wide Antenna Radiation Pattern … 120 Figure 121. LOC MRN-7 Dipole Antenna Radiation Pattern … 121 Figure 122. LOC Redlich LPD (14-10) Antenna Radiation Pattern … 122 Figure 123. LOC Mod. V Ring Antenna Radiation Pattern … 123 Figure 124. LOC 1201 Dipole Antenna Radiation Pattern … 124 Figure 125. LOC 1203 Dipole Antenna Radiation Pattern … 125 Figure 126. LOC 1204 Dipole Antenna Radiation Pattern … 126 Figure 127. LOC 1261 Dipole Antenna Radiation Pattern … 127 Figure 128. LOC STAN37 Dipole Antenna Radiation Pattern … 128 Figure 129.

LOC Twin Tee Antenna Radiation Pattern … 129 Figure 130. LOC Standard 14 el V-Ring Antenna Radiation Pattern … 130 Figure 131. DME Unidirectional Antenna Radiation Pattern … 131 Figure 132. DME Bi-directional Antenna Radiation Pattern … 132 Figures 133. thru 140. Reserved … 132 SECTION 4. CHECKING AN FAA PROPOSED ILS FREQUENCY WITH THE AAM 31. ILS Frequency Study Procedure … 139 32. Step By Step Study Procedure … 139 33. Study Results … 140 34. thru 40. Reserved … 140 Figure 141a. AAM Printout Page 1 … 141 Figure 141b. AAM Printout Page 2 … 142 Figure 142a. AAM Printout Page 1 … 143 Figure 142b. AAM Printout Page 2 … 144 Figure 142c. AAM Printout Page 3 … 145 Figure 142d. AAM Printout Page 4 … 146

Page xii

11/17/05 Table of Contents - continued 6050.32B

Figure 142e. AAM Printout Page 5 … 147 Figure 142f. AAM Printout Page 6 … 148 Figures 143. thru 154. Reserved … 148 SECTION 5. NAVAID RECEIVER TEST FACILITIES FREQUENCY ENGINEERING 41. Frequency Engineering For VOT Test Facilities … 151 42. Frequency Engineering For Secondary Receiver Test Facilities … 151 43. VOT Frequency Engineering By the Table Method … 152 Figure 155. Cochannel Separation of VOT and Operating VORs … 152 Figure 156. LOC Radii Defined, Cochannel … 152 Figure 157. Cochannel Separation of ILS and ILS-Test … 153 44. VOT Frequency Engineering By the Calculation Method … 153 Figure 158. VOR Versus Cochannel VOT By Calculation … 153 45. thru 50. Reserved … 154 Figure 159. VOR/VOT Cochannel Facility Separation Curves +14 dbW … 155 Figure 160. VOR/VOT Cochannel Facility Separation Curves +17 dBW … 156 Figure 161. VOR/VOT Cochannel Facility Separation Curves +20 dBW … 157 Figures 162. thru 164. Reserved … 157 SECTION 6. ESV FREQUENCY ENGINEERING 51. Frequency Engineering For ESV … 165 52. Minimum Power Available Requirements … 165 Figure 165.

Power Available Requirements For NAVAID Receivers … 165 53. An Example Of Power Availability … 165 Figure 166. Power Available - VOR … 166 54. The Interrelationship Of the VOR and DME/TACAN ESV … 166 55. VOR/DME/TACAN ESV Determination Procedure … 166 Figure 167. Critical Point Measurement of an ESV … 167 Figure 168. Example of VOR ESV By Calculation … 167 56. ILS-DME ESV Determination Procedure … 168 57. ESV Special Considerations … 168 Figure 169. Sample ESV Record Format … 169 58. thru 62. Reserved … 169 Figure 170. Power Available Curves - 100 W - VOR 0-50 nmi … 170 Figure 171. Power Available Curves - 100 W - VOR 0-220 nmi … 171 Figure 172. Power Available Curves - 5 kW - TACAN 0-50 nmi … 172 Figure 173. Power Available Curves - 5 kW - TACAN 0-220 nmi … 173 Figure 174. Power Available Curves - 100 W - Cardion DME 0-50 nmi … 174 Figure 175. Power Available Curves - 100 W - Cardion DME 0-220 nmi … 175 Figure 176. Power Available Curves - 100 W - Montek DME 0-50 nmi … 176 Figure 177. Power Available Curves - 100 W - Montek DME 0-220 nmi … 177 Figure 178.

Power Available Curves - 1 kW - Cardion DME 0-50 nmi … 178 Figure 179. Power Available Curves - 1 kW - Cardion DME 0-220- nmi … 179 Figure 180. Power Available Curves - 1 kW - Montek DME 0-50 nmi … 180 Figure 181. Power Available Curves - 1 kW - Montek DME 0-220 nmi … 181 Figure 182. Power Available Curves - 100W - FA10153 DME 0-50 nmi … 182 Figure 183. Power Available Curves - 100W - FA10153 DME 0-220 nmi … 183

Page xiii

6050.32B Table of Contents - continued 11/17/05

Figure 184. Power Available Curves - 100W - dBS5100A DME 0-50 nmi … 184 Figure 185. Power Available Curves - 100W - dBS5100A DME 0-220 nmi … 185 Figure 186. Reserved … 185 SECTION 7. MLS AND DME/P FREQUENCY ENGINEERING 63. Frequency Engineering For MLS and DME/P … 197 Figure 187. FPSV For MLS Approach Azimuth/Data Coverage … 197 Figure 188. FPSV For MLS Approach Elevation Coverage … 198 Figure 189. FPSV For MLS Back Azimuth/Data Coverage … 199 Figure 190. FPSV For MLS DME/P … 200 Figure 191. Interim MLS Cochannel and Adj. Channel Separation D/U Values … 201 Figure 192. DME/P Cochannel and Adjacent Channel Separation D/U Values … 201 64. Frequency Engineering Procedures … 202 65. MLS Intersite Analysis By Table Method … 202 Figure 193. Interim MLS Cochannel Separation Distance … 202 66. DME/P Intersite Analysis By Table Method … 203 Figure 194. MLS DME/P Assignment Criteria … 203 67. thru 70. Reserved … 203 Figures 195 thru 200 Reserved … 203 SECTION 8. LOCAL AREA AUGMENTATION SYSTEM FREQUENCY ENGINEERING 71. Frequency Engineering … 211 Figure 201.

LAAS/LAAS/VOR Separation Criteria … 211 72. Frequency Engineering Procedures … 212 73. Intersite Analysis by the Table Method for LAAS … 212 Figure 202. LAAS/LAAS Cochannel Separations … 212 Figure 203. LAAS/VOR Interim 1st Adjacent Channel 50 kHz Separations … 213 Figure 204. LAAS/VOR Final 1st Adjacent Channel 50 kHz Separations … 213 APPENDIX 4. TECHNICAL DATA FOR VHF/UHF/SHF LINKS Figure 1. Technical Parameters, ATT FR8 RCL … 1 Figure 2. FR8 Interference Susceptibility Curves … 2 Figure 3. Technical Parameters, TML … 3 Figure 4. TML Interference Susceptibility Curves … 4 Figure 5. FAA Low Density RCL Path Design Criteria … 5 Figure 6. MDR 6X08 Specifications … 6 Figure 7. Nomograph For Free Space Propagation Loss … 7 Figure 8. Nomograph For Parabolic Antenna Gain … 8 Figure 9. Available Computer Analysis Models … 9 APPENDIX 5. GLOSSARY (9 pages) … 1 APPENDIX 6. EMISSION DESIGNATORS (2 pages) … 1 APPENDIX 7. FORMULAS USED IN THIS ORDER (1 page) … 1

Page xiv

11/17/05 Table of Contents - continued 6050.32B

APPENDIX 8. SOME PROCEDURES FOR RADAR ANTENNA VERTICAL PATTERN MEASUREMENT BY SOLAR MEANS 1. General … 1 2. Two Methods of Solar Measurements … 1 3. Manual Measurement … 1 Figure 1. Block Diagram of Manual Measurement … 2 Figure 2. Sample Recording With Calibration, Time and Amplitude Markings … 5 Figure 3. Sample Plot of Analyzed Recording … 6 4. Automated Measurement … 6 Figure 4. Automated Radar Antenna Solar Measurement Block Diagram … 7 5. Documentation … 8

Page xv (and xvi)

TOC3-final_ix-x 06-11-2019 (004) › 04_Chap 01_6050.32B_111705.pdf

11/17/05 6050.32B

CHAPTER 1. GENERAL 1. PURPOSE. This order establishes and describes the spectrum management function in the Federal Aviation Administration (FAA) and delineates policies and procedures for the allocation and engineering of this scarce resource. 2. DISTRIBUTION. This order is distributed to the director level in headquarters, the William J. Hughes Technical Center, and the Mike Monroney Aeronautical Center; to division level in the Technical Operations, Enroute and Oceanic, and Terminal Service Areas; and to all field offices with a supervisory distribution. 3. CANCELLATION. This order cancels and supersedes Order 6050.32A, dated May 1, 1998. 4. EXPLANATION OF CHANGES. a. Many chapters and appendices have been updated and expanded to reflect, in particular, current FAA policy and ensure appropriate guidance in addressing the broad range of issues related to aeronautical radio frequency spectrum engineering and usage. A number of the more significant changes are highlighted in the following items.

b. Chapter 8 has been updated with new guidance on Obstruction Evaluation notification requirements and automation tools. c. Chapter 9 has been updated to include guidance regarding the Sustaining Backup Emergency Communications (BUEC) systems, as well as guidance on temporary frequency assignments for, in particular, Air Shows and Fire Fighting. d. Chapters 14 and 15 have been updated to reflect the current automation and analysis tools to better detect, document, and resolve radio frequency interference (RFI) cases. e. Chapter 16 has been expanded to address guidelines for radiation hazard measurements and related procedures, as a result of the cancellation on April 22, 1999, of FAA Order 3910.3A, Radiation Health Hazards and Protection, dated October 19, 1983. f. Chapter 17 has been updated to reflect new frequency allotments, a new channel plan, additional fixed communications systems, and new transmit emission standards. g. Chapter 19 has been renamed to Automated Engineering (previously Automated Frequency Manager (AFM)) and expanded to more broadly reflect the increased use of automation in satisfying spectrum engineering and analysis functions. h. Appendix 2 has been updated to reflect new policy changes to the engineering criteria and frequency uses that have been developed for the Air-Ground VHF Communications frequency bands. i. A new Appendix 3, Section 8 has been added to address Local Area Augmentation System (LAAS) frequency engineering.

6050.32B Chapter 1 - continued 11/17/05

Page 2 (thru 6)

5. FORMS. The following forms may be obtained from the FAA Depot through normal supply channels (see the latest edition of Order 1330.3): a. FAA Form 6050-1, Facility Transmitting Authorization, NSN 0052-00-688-6001; unit of issue: sheet. b. FAA Form 6050-2, Transmitter Identification and Operation Authorization, NSN 0052-00-694-9000; unit of issue: sheet. c. FAA Form 6050-4, Expanded Service Volume Request, NSN 0052-00-845-6000, unit of issue: set. 6. thru 199. RESERVED.

TOC3-final_ix-x 06-11-2019 (004) › 05_Chap 02_6050.32B_111705.pdf

11/17/05 6050.32B

CHAPTER 2. THE RADIO FREQUENCY (RF) SPECTRUM 200. RF SPECTRUM. The RF or electromagnetic spectrum is a finite natural resource used by every country in the world. The internationally used frequency unit is the "Hertz," named for an early pioneer in spectrum research. The Hertz (Hz) is defined as one cycle per second (cps), with further prefixes from the Greek to indicate multipliers. One thousand Hz is defined as 1 kiloHertz (kHz), one million Hz is 1 MegaHertz (MHz) and one billion Hz is 1 GigaHertz (GHz), etc. The electromagnetic spectrum emissions of interest, which are called the radio frequency bands, begin at 10 kHz and end at 300 GHz. Above 300 GHz are visible light, X-rays, gamma rays and other electromagnetic phenomena. 201. MAKEUP OF THE SPECTRUM. a. By international agreement, the radio spectrum is divided into major bands in frequency decimal multiples of three. The radio spectrum was originally defined in terms of metric system wavelengths.

The three multiple came into use because the speed of light and electromagnetic propagation is about 300 million meters per second in free space. The length of a full wavelength is 3 x 108 meters per second (m/s) divided by the frequency in Hz. Noting this frequency/wavelength relationship, a frequency of 3 MHz calculates to 100 meters for a full wavelength. b. These decade bands of frequencies have international defined names, using common terms. For example, the band of frequencies from 30 kHz to 300 kHz is named Low Frequency (LF) and 300 kHz to 3 MHz is designated Medium Frequency (MF). The bands continue from LF and MF to High (HF), Very High (VHF), Ultra High (UHF) and Super High (SHF) with continuations above and below these ranges. The frequency band names are divided by decimal breaks defined in wavelengths; e.g., 300 kHz is 1000 meters, 3,000 kHz is 100 meters, etc. The United States uses frequency in Hz as the unit for specific administrative tracking of spectrum assignments. 202. SPECTRUM LIMITATION CONSIDERATIONS. a.

Aeronautical safety systems shall be accommodated in aeronautical spectrum which is specifically allocated for the service being satisfied and which is used exclusively by aeronautical safety systems. This ensures protection from non-aeronautical users so that the high levels of integrity and availability required by civil aviation can be met. b. Congestion within the available spectrum is not the only factor limiting its use. First and primarily are the international agreements and treaties to which the United States is a signatory. These matters are covered in detail in chapter 3. Second is the necessary frequency bandwidth required to convey the transmitted information. Other considerations are spectrum efficiency, propagation, capacity, equipment, economics and interference. c. International agreements divide the spectrum into bands for either exclusive or shared use by a specific service. The aeronautical service is just one of many defined services which have allocations in specific and limited bands.

The aeronautical mobile (R) and aeronautical radionavigation services are directly related to safety of life and property in the air. Therefore, most such bands are allocated exclusively worldwide, where the operations deal directly with operation of aircraft. Ancillary aeronautical services, such as fixed microwave point-to-point systems, are shared with other users. d. Aeronautical service frequency bands are distributed throughout the radio spectrum.

6050.32B Chapter 2 - continued 11/17/05

e. Propagation characteristics play a major role in the limitations on use of the assigned spectrum. LF and MF operate primarily on groundwave and can cover hundreds or thousands of miles day or night quite reliably. HF uses the ionosphere to reflect signals for great distances around the earth, but are greatly affected by day-to-night and seasonal changes. Beginning around the VHF band, "radio line-of-sight" (RLOS) propagation conditions exist. RLOS extends the visual line-of-sight distance by virtue of the phenomenon that radio waves "bend" near large objects such as the earth. See the Appendix 2 for details. At VHF frequencies and above, radio signals travel in a straight line, modified by the bending of the path due to the RLOS effect. Large metallic or electrically-conducting objects such as steel buildings will attenuate, retard or deflect the signal's path. Signal reflection occurs under some conditions, but it is not considered as a reliable path except where the reflector is a part of the planned path. f.

Technical equipment, particularly its changing style as the state-of-the-art progresses, places severe restrictions on the spectrum engineer in engineering frequencies. For example, the original channel assignments in the VHF communications band were every 200 kHz on the odd frequencies between 118.1 and 126.9 MHz, e.g., 118.1, 118.3, etc. Congestion required narrowing the channels to 100 kHz so frequencies could then be assigned on every decimal frequency, 118.1. 118.2, etc. While technically the number of channels doubled per MHz, all could not be used simply. There were still thousands of 200 kHz channeled transceivers in use. It took years of education and finally agency orders to permit the spectrum engineer full use of the 100 kHz channels. Subsequent congestion brought further reduction to 50 kHz, then currently to 25 kHz channels, yet protection for a "grandfather" period for older operating equipment always must be given. g. Economics also has a very big impact on the spectrum engineer's ability to engineer frequencies.

As described in subparagraph e, even though revised frequency engineering allocations establishes additional channels, they may not necessarily be able to be used. Whether airline or a private aircraft owner, the ability to meet all the requirements for new equipment to meet technological advances is limited by the ability to pay for it. h. Interference can be defined as any undesired signal or energy which prohibits or degrades the normal reception of the desired signal. It can be divided into three broad categories; adjacent channel or cochannel radio sources, man-made electrical noise, and natural solar and atmospheric noise. (1) Adjacent channel or cochannel interference is caused by undesired radio transmissions which the receiving device is unable to separate from the desired transmission. Adjacent channel interference is caused by emitters using nearby channels and occurs because of the inability of the pass band of the victim receiver to discriminate against near-frequency signals.

Cochannel interference is caused by emitters using the same frequency which are too close geographically. Proven radio frequency spectrum engineering criteria are used by the spectrum engineer to establish an interference-free assigned frequency. (2) Man-made interference is the most common and most insidious. The sources are limitless, from "plastic welders," to electric motors of all types, to the incidental and spurious radiation of other transmitters. In addition, there are cases of intentional interference, so-called "bogus" or "phantom" controllers, which FAA must investigate (and prosecute) with the help of other agencies. (3) Solar and atmospheric noise are outside human control. The sun emits an enormous amount of energy throughout the spectrum, varying in day-to-day intensity and frequency. In frequencies through VHF, solar radiation and atmospheric noise such as lightning and precipitation static are significant. From UHF and above, noise generated internally in equipment is the controlling factor.

11/17/05 Chapter 2 - continued 6050.32B

(4) Intermodulation is defined as the presence of unwanted signals at the output of a less-than-ideal amplifier resulting from modulation of the components of a complex waveform by each other in a nonlinear system. When two or more signals are applied to a nonlinear device, a mixing or intermodulation action results and signals are produced, having frequencies equal to the sums and differences of the original input signals, among other signals. An otherwise linear device may be driven into nonlinear operation in the presence of strong external signal levels. Although most cases occur in receivers, problems do occur when two or more transmitters start radiating a mixed frequency created when a mix occurs in their final amplifiers, particularly when their antennas are in close proximity. Detailed information will be found in Appendix 2. (5) Desensitization is the deterioration of reception of a desired signal due to the proximity of a very strong signal. The source of the problem could be of any frequency theoretically, but in practice, communications frequencies usually are effected only by very strong signals below about 1 GHz. The strong signal drives the receiver into non-linear function, desensitizing normal reception as well as generating many unwanted spurious signals within the receiver. 203. thru 299. RESERVED.

Page 9 (thru 16)

11/17/05 6050.32B

CHAPTER 3. HISTORY, AUTHORITIES, AND RESPONSIBILITIES 300. GENERAL CONSIDERATIONS. The FAA, as one of the major users of the RF spectrum in the United States, has an important national role in the management of frequencies. In turn, the nation has a major responsibility to the rest of the world in the orderly development and application of the RF spectrum within the international community. To acquaint the reader with the need for effective spectrum management within the agency, this chapter presents an historical background of the development and current national and international administrative authorities and responsibilities. Although it complicates the task, agency spectrum management is bound by many international treaties, as well as the regulatory framework imposed by the dual spectrum control entities in the United States: the Federal Communications Commission (FCC) and the National Telecommunications and Information Administration (NTIA). 301. INTERNATIONAL ORGANIZATIONS. a. International Telecommunication Union (ITU). (1) ITU.

TOC3-final_ix-x 06-11-2019 (004) › 06_Chap 03_6050.32B_111705.pdf

The ITU is an arm of the United Nations, with its headquarters in Geneva, Switzerland. It is the fundamental authority for spectrum allocation and management. The ITU currently has a membership of nearly 190 nations, and 650 Sector Members (companies). The organization is one of the oldest international groups in existence. In 1932, it became the successor to the International Telegraph Union that was created in 1865. (2) ITU Authority. The ITU expresses its authority through the same channels as any other multilateral treaty system. Regulations adopted by this international body must then be ratified further and signed by the various administrations (nations) represented. These regulations are developed at conferences and through negotiation where representatives of member nations formulate recommendations that are presented to the plenary body in session for formal voting action leading to adoption.

The adopted policies are then published and include detailed regulations and policies in such areas as terminology, assignment and use of frequencies, band allocations, frequency registration, technical specifications, measures against interference, administrative provisions for stations and distress and safety procedures. (3) Structure of the Union. An organizational diagram of the ITU, showing major functions of concern to the FAA, is presented in figure 3-1. Some major activities and elements of the Union are as follows: (a) Plenipotentiary Conference. Meeting at intervals of normally not less than 5 years, the Plenipotentiary Conference determines the general policies for fulfilling the purposes of the Union. It reviews the work of the Union and revises the Convention (organization definition) if considered necessary. (b) World Radiocommunication Conference (WRC). A WRC is normally convened every three to four years to consider specific radiocommunication matters.

A WRC may revise the Radio Regulations, or deal with any radiocommunication matter of worldwide character in accordance with its agenda. The Radio Regulations constitute an international treaty on radiocommunication and cover the use of the radio frequency spectrum by radiocommunication services. (c) Council. The Council sets the final agenda for a WRC, normally two years before the conference is held.

6050.32B Chapter 3 - continued 11/17/05

FIGURE 3-1. PARTIAL ORGANIZATIONAL CHART OF THE ITU

11/17/05 Chapter 3 - continued 6050.32B

(d) Secretary General. The Secretary General is responsible to the Council for external relations, public information and other directed functions. The office provides secretarial services for all conferences and publishes the monthly journal services in several languages for distribution to member nations. (e) Radiocommunication Sector. The Radiocommunication Sector is one of three major Sectors directly under the authority of the Plenipotentiary Conference and the Council. Its primary functions are to provide for international frequency registration, technical and administrative support to radiocommunication study groups, to provide conference and assembly support and to provide seminars and training. b. International Civil Aviation Organization (ICAO). ICAO is to the international scene as FAA is to the national, except that it is only advisory, without authority to enforce its recommendations. Member nations, including the United States, strive for strict adherence to ICAO standards. See figure 3-2.

The following is a summary of the ICAO goals: (1) Ensure safe and orderly growth of international aviation throughout the world. (2) Encourage the arts of aircraft design and operation for peaceful purposes. (3) Encourage the development of airways, airports and air navigation facilities for international civil aviation. (4) Meet the needs of the people of the world for safe, regular, efficient and economical air transport. (5) Prevent economic waste caused by unreasonable competition. (6) Ensure that rights of contracting nations are respected fully and those nations given equal opportunity. (7) Promote safety of flight in international air navigation.

(8) Annexes to the ICAO Convention (the "Chicago Convention" which established ICAO) establish international standards and recommended practices (SARPs) for aeronautical requirements such as licensing, airworthiness, security, air traffic, search and rescue, communications, etc. "Standards" are necessary for the safety or regularity of international aviation and "recommended practices" are desirable for the safety or regularity of international aviation.

6050.32B Chapter 3 - continued 11/17/05

FIGURE 3-2a. ICAO ASSEMBLY ORGANIZATION CHART

FIGURE 3-2b. ICAO SECRETARIAT ORGANIZATION CHART

11/17/05 Chapter 3 - continued 6050.32B

(9) ICAO operates and functions as follows: (a) The Assembly is the sovereign body of ICAO and includes over 180 Contracting States. It meets at least once every three years and handles broad policy issues. Each contracting State has one vote on an issue. (b) The Council is the governing body of ICAO. It is a resident body comprised of 33 representatives from Member States elected by the Assembly for three-year terms. One of the primary duties of the Council is to adopt SARP's and incorporate these as Annexes to the Convention to achieve international uniformity/standardization and improve air safety, efficiency and regularity of flight. The U.S. has had a representative member on the Council since the beginning of ICAO. (c) The Air Navigation Commission (ANC) is comprised of 15 qualified technical experts from Member States appointed by the Council. ANC is responsible for examining, coordination and planning all of ICAO's work in the air navigation field and is the principal body concerned with developing SARPs.

The ANC forms panels and study groups consisting of outside technical experts to study specific issues and make recommendations to the Council. A technical expert nominated by the U.S. has been a member of the Commission since the beginning of ICAO. This expert has historically had an FAA background. 1. While Headquarters Monitors work on nearly all ICAO Panels, the two which routinely address radio spectrum issues and on which Headquarters participates, are the Aeronautical Mobile Communications Panel (AMCP) and the Global Navigation Satellite System Panel (GNSSP). Working Group F of the AMCP addresses aeronautical radio spectrum issues in general, and develops the ICAO position for WRCs. 2. AMCP studies aeronautical mobile communications issues and develops SARPs for airground communications, satellite communications and associated systems. GNSSP is developing the SARPs for the future Global Navigation Satellite System (GNSS). (d) The Air Transport Committee normally does not address radio spectrum issues.

It is comprised of representatives from Member States who are appointed by the Council. Its work includes research and recommendations such as policy guidance on airport and route facility economics and management. It considers air transport issues in global conferences. The Air Transport Committee also forms panels and study groups to process its work. (e) The Secretariat serves as ICAO's permanent administrative body. The Secretariat staff maintains ICAO documents and its bodies include the Air Navigation Bureau, the Aviation Security Branch and the Technical Assistance Bureau. The Secretariat also administers the Seven Regional ICAO Offices which develop and implement regional aviation initiatives. 302. NATIONAL ORGANIZATIONS - GENERAL. Each member nation of ITU is free to set up its own procedures for authorizing the use of the spectrum within its nation, but consistent with the international table of allocations approved by the last ITU conference.

Exceptions may be taken to specific allocations, but a member nation must notify ITU and be subject to conflicting use by other member nations following the allocations. a. United States International Relations. In the United States, the State Department is responsible for the international representation of the United States in ITU (as well as ICAO) forums, utilizing the full technical and administrative support by all concerned United States agencies. The State Department acts as the ITU voting member. The vote represents the consensus of an extensive NTIA/FCC preparatory process, or when a consensus cannot be reached, the official position of the President. The State Department provides the liaison between the United States and other governments when conflicts arise over application of the ITU Radio Regulations.

6050.32B Chapter 3 - continued 11/17/05

b. United States Domestic Structure. The Communications Act of 1934, as amended, established a dual system of control of the spectrum within the United States. The FCC administers all the spectrum assigned to and operated by non-Federal agencies. The Act also specifies that all Federal agencies will have their spectrum needs administered and authorized by a separate agency, currently the NTIA in the Department of Commerce (DOC). Both agencies, FCC and NTIA, work together to formulate recommendations for national control of the spectrum, as well as supply the Department of State with a consensual position for international conferences. c. FCC. (1) Jurisdiction. The FCC has jurisdiction over all non-Federal Government spectrum and spectrum users in the United States. This includes not only broadcast, amateur, industrial, and civil aviation as it applies to licensing the operators and equipment, but also State and municipal government entities as well. (3) Organization. The Commission is composed of five commissioners, appointed by the President with the advice and consent of the Senate. They serve 5-year staggered terms, so one term expires each year. There can be no more than three commissioners from the same political party. One of the members is appointed by the President to be Chair. A simplified block diagram of FCC organization is found in figure 3-3.

FIGURE 3-3. FEDERAL COMMUNICATIONS COMMISSION

11/17/05 Chapter 3 - continued 6050.32B

d. NTIA. (1) Jurisdiction. NTIA has authority and responsibility for use of the Federal portion of the spectrum by all Federal agencies, including the DOD and the FAA. It is empowered by the same Act as FCC, but has only the Federal agencies' spectra to administer. NTIA and FCC work closely together, since a good portion of the radio spectrum is shared between Federal and non-Federal users requiring joint action. A block diagram of NTIA is shown in figure 3-4. (2) Responsibilities. NTIA is responsible for administering that portion of the spectrum allocated to Federal use. It is empowered to authorize Federal agencies, which demonstrate appropriate needs and satisfy specific requirements, to use the spectrum. They can also withdraw that authorization or modify it if required. NTIA is also bound by the ITU Radio Regulations. FAA's interface with NTIA is normally only at the Washington level.

6050.32B Chapter 3 - continued 11/17/05

FIGURE 3-4. NATIONAL TELECOMMUNICATIONS

AND INFORMATION ADMINISTRATION

11/17/05 Chapter 3 - continued 6050.32B

(3) Organization. The NTIA Administrator serves as the Special Assistant to the President for Telecommunications. NTIA is currently located in Washington in the DOC. It has no field offices, but in effect does have various "field representatives" in other agencies in the field. For instance, each FAA service area Frequency Management Officer (FMO) is the NTIA's field coordinator for all radar beacons and all radars within certain radar bands. This includes military and non-Federal radars and radar beacons. (a) Interdepartment Radio Advisory Committee (IRAC). The IRAC, chaired by the NTIA Deputy Associate Administrator for Domestic Spectrum Management, is one of the most important bodies which interfaces with FAA frequency management. Authorization for all FAA frequencies, including our Land Mobile networks comes through IRAC from NTIA. The IRAC is the working arm of NTIA, composed of 20 members, each an agency of the Federal Government, including FAA. See figure 3-5. FAA participates and provides technical expertise to all subcommittees of the IRAC.

FIGURE 3-5. PARTIAL ORGANIZATION CHART OF THE IRAC (b) Spectrum Planning Subcommittee (SPS). The SPS carries out IRAC functions which relate to planning for the use of the electromagnetic spectrum. This includes the apportionment of spectrum space for the support of established or anticipated radio services, as well as the apportionment of spectrum space between or among Government and non-Government activities. (c) Technical Subcommittee (TSC). The TSC is a subcommittee of IRAC which examines the technical aspects of the use of the electromagnetic spectrum. (d) Radio Conference Subcommittee (RCS). The RCS advises the IRAC in those functions relating to preparing for ITU radio conferences. This includes the development of recommended U.S. proposals and positions.

6050.32B Chapter 3 - continued 11/17/05

(e) Emergency Planning Subcommittee (EPS). In general, the EPS formulates, guides, and reviews National Security Emergency Preparedness (NSEP) planning for Federal spectrum-dependent systems. (f) Space Systems Subcommittee (SSS). The SSS, chaired by the NTIA, is responsible to the IRAC for international registration of Government within the ITU forum. (g) Frequency Assignment Subcommittee (FAS). The FAS is an IRAC subcommittee, which operates to accomplish all the engineering and coordination for each agency's frequency requests. To facilitate its work, FAS has specialized groups to assist with the enormous task of checking and coordinating every frequency request. The following are the two most important groups to FAA: 1. Aeronautical Assignment Group (AAG). The AAG, chaired by the FAA, handles only those frequencies which deal with aeronautical services, both Federal and non-Federal. In so doing, it can tentatively "authorize" frequencies in that service directly to the FMO in the service area after assuring the request meets all IRAC and FAA requirements. Aeronautical frequencies approved by AAG must be approved by the FAS before they become final. The frequency bands under AAG control are shown in figure 3-6.

FIGURE 3-6. AAG CONTROLLED BANDS 190-285 kHz 285-435 kHz* 510-535 kHz* 74.8-75.2 MHz 108-121.9375 MHz inclusive 123.5875-128.8125 MHz inclusive 132.0125-136.0000 MHz inclusive 328.6-335.4 MHz 978-1020 MHz inclusive 1030 MHz 1031-1087 MHz inclusive 1090 MHz 1104-1146 MHz inclusive 1157-1213 MHz inclusive 5000-5250 MHz inclusive *In these bands, only applications for stations in the Aeronautical Radionavigation Service shall be sent to the AAG.

2. Military Assignment Group (MAG). The MAG does the same work as AAG, except for the military fixed and mobile communications bands controlled by DOD, 225.000-328.600 MHz and 335.400-399.950 MHz only. FAA requests for use of those frequencies for A/G facilities must go through MAG for initial approval. (h) Field Coordinators. Because the IRAC lacks expertise in some areas, it needs field assistance in its enormous task of coordinating some operations. As a result, the FAA and the DOD Area Frequency Coordinators (AFC) are tasked with pre-coordination of some portions of the spectrum before the frequency request is submitted to FAS or IRAC.

11/17/05 Chapter 3 - continued 6050.32B

1. FAA Field Coordinators have responsibility for coordinating certain radar frequency bands. This entails the FMOs having to engineer each new radar or beacon request proposed for operation in their service area, whether civilian test, military, other Federal agency use or FAA. Once the frequency or (in the case of radar beacon) the Pulse Repetition Rate (PRR) has been engineered, it must be given to Technical Operations ATC Spectrum Engineering Services for submission to IRAC through channels. Those bands are shown in figure 3-7.

FIGURE 3-7. BANDS UNDER COORDINATION CONTROL

OF FAA FIELD COORDINATORS 1030 MHz Airborne Radar Beacons (Interrogators) 1090 MHz Ground Transponders 1215-1400 MHz Radar (typically en route radar) 2700-2900 MHz Radar (typically terminal and weather radar) 9000-9200 MHz Radar (typically DOD precision approach radar)

2. DOD AFCs have a similar responsibility but for the telemetry bands 1435-1535 MHz and 2310-2390 MHz. FAA does not use these bands. DOD AFC responsibilities are covered in the NTIA Manual, chapter 8. (4) Spectrum chart. A wall size detailed graphic representation of the full spectrum is published by NTIA and is available from Technical Operations ATC Spectrum Engineering Services upon request. e. FAA. The spectrum management function in FAA is totally within the purview of Technical Operations ATC Spectrum Engineering Services. The latest edition of Orders 1100.1, FAA Organization - Policies and Standards, 1100.2, Organization - FAA Headquarters and 1100.5, FAA Organization - Field delineate the specific functions of the office. Figure 3-8 provides a block diagram of Technical Operations ATC Spectrum Engineering Services. Figure 3-9 lists the bands of frequencies with which FAA is concerned.

6050.32B Chapter 3 - continued 11/17/05

FIGURE 3-8. TECHNICAL OPERATIONS ATC SPECTRUM ENGINEERING SERVICES

Office of ATC Spectrum Engineering

Services

Program Director

Chief Systems Engineer Secretary

Management and

Program Analyst

Spectrum Planning and

International

Office

Spectrum Assignment and Engineering Office

Mike Monroney

Aeronautical

Center

William J. Hughes

Technical Center

11/17/05 Chapter 3 - continued 6050.32B

FIGURE 3-9. SUMMARY OF FREQUENCY BANDS SUPPORTING AVIATION

9 - 14 kHz OMEGA Navigation System 90 - 110 kHz LORAN C Navigation System * 190 - 435 kHz Nondirectional Beacon * 510 - 535 kHz Nondirectional Beacon 2100 - 28,000 kHz High Frequency Communications * 74.8 - 75.2 MHz NAVAID (Marker Beacon) * 108 - 112 MHz NAVAID (VOR, ILS Localizer) * 112 - 118 MHz NAVAID (VOR, LASS and SCAT-I)) * 118 - 137 MHz VHF Air/Ground Communications 62 - 174 MHz Fixed, mobile Communications 225.0 - 328.6 MHz UHF Air/Ground Communications * 328.6 - 335.4 MHz NAVAID (ILS Glide Slope) 335.4 - 399.9 MHz UHF Air/Ground Communications 406.0 - 406.1 MHz Satellite Emergency Position Indicating Radio Bcn 406.1 - 420.0 MHz Fixed, Mobile Communications 932 - 935 MHz Fixed Communications 941 - 944 MHz Fixed Communications * 960 - 1215 MHz NAVAID (TACAN/DME, etc.) * 978 MHz ADS-B (UAT) * ** 1030 MHz Radar Beacon, TCAS, Mode S * ** 1090 MHz Radar Beacon, TCAS, Mode S * 1176.45 MHz Planned Global Positioning System (L5) 1227.6 MHz Global Positioning System (L2) ** 1215 - 1390 MHz Air Route Surveillance Radar 1544 - 1545 MHz Emergency Mobile Satellite Communications 1545 -

1559 MHz Aeronautical Mobile Satellite (R) (Downlink) 1559 - 1610 MHz GPS (L1), GLONASS 1645.5 - 1646.5 MHz Emergency Mobile Satellite Communications 1646.6 - 1660.5 MHz Aeronautical Mobile Satellite (R) (Uplink) 1710 - 1850 MHz Low Density Microwave Link ** 2700 - 2900 MHz Airport Surveillance Radar, Weather Radar 2900 - 3000 MHz Weather Radar 3700 - 4200 MHz ANICS (commercial satellite downlink) 4200 - 4400 MHz Airborne Radio altimeter * 5000 - 5250 MHz NAVAID (Microwave Landing System) 5350 - 5470 MHz Airborne Radar and Associated Airborne Beacon 5600 - 5650 MHz Terminal Doppler Weather Radar 5925 - 6425 MHz ANICS (commercial satellite uplink) 7125 - 8500 MHz Radio Communications Link 8750 - 8850 MHz Airborne Doppler Radar ** 9000 - 9200 MHz Military Precision Approach Radar 9300 - 9500 MHz Airborne Radar and Associated Airborne Beacon 11.70 - 12.20 GHz FAATSAT (commercial satellite downlink) 13.25 - 13.40 GHz Airborne Doppler Radar 14.00 - 14.50 GHz FAATSAT (commercial satellite uplink) 14.50 - 15.35 GHz Television (Video) Microwave Link 15.70 - 16.20 GHz Airport Surface

Detection Equipment (ASDE III) 21.20 - 23.60 GHz Microwave Link (Multi-use) 24.45 - 24.65 GHz Airport Surface Detection System (ASDE II) * denotes AAG bands engineered by FAA; see NTIA Manual ** denotes those bands for which FAA is national coordinator; see NTIA Manual

6050.32B Chapter 3 - continued 11/17/05

303. TECHNICAL OPERATIONS ATC SPECTRUM ENGINEERING SERVICES. The following are the major assigned functions for Technical Operations ATC Spectrum Engineering Services: a. Focal point within the FAA for all radio spectrum matters. Develops and executes FAA radio frequency spectrum policy, plans and standards. b. Engineers, obtains authorizations and protects those frequency assignments necessary to satisfy the requirements of the National Airspace System (NAS). c. Provides engineering support to service area and field facilities in the resolution and prevention of radio frequency interference to NAS facilities. d. Manages the classified frequency management data and associated secure computer facility at Headquarters. e. Performs engineering analysis of frequency assignment proposals by Government agencies, the FCC (for non-Government aviation use), Canada, Mexico and other countries to determine the impact on the NAS, and to preclude radio frequency interference to NAS facilities and services. f.

Represents the agency on the IRAC and other Government and industry spectrum management committees and working groups and Federal advisory committees which address spectrum issues. g. Serves as the manager of aeronautical frequencies in the United States. Manages and engineers those aeronautical frequencies identified for AAG management and chairs that group. In addition, the NTIA has delegated band coordinator responsibilities to the FAA for radar (1215-1390, 2700-2900 and 9000-9200 MHz bands) and the radar beacon (1030/1090 MHz) systems. h. Assists in developing the United States' position and inputs for use in various international meetings. Represents the United States at those ITU and ICAO meetings that require frequency management technical expertise and which address or impact civil aviation matters. I. Maintains the FAA radio frequency portion of the Federal Government's recovery communications (RCOM) mobilization plans. j.

Conducts engineering studies relating to incorporation of future communications, navigation and surveillance (CNS) systems within assigned portions of the radio spectrum in accordance with the NAS Capital Investment Plan (CIP) and FAA Research, Engineering and Development Plan. k. Executes the electromagnetic radiation hazard measurement program, both ionizing and non-ionizing, for all FAA equipment and systems. l. Administers the electromagnetic compatibility portion of the agency's airspace case program. 304. SERVICE AREA FREQUENCY MANAGEMENT OFFICE (FMO). The following are the major functions assigned to the service area frequency management office: a. Serves as the focal point within the service area for all frequency matters. b. Investigates and resolves Radio Frequency Interference (RFI) problems.

11/17/05 Chapter 3 - continued 6050.32B

c. Validates and forwards frequency requirements with specific recommended frequencies to Technical Operations ATC Spectrum Engineering Services. d. Performs electromagnetic compatibility studies. e. Performs radiation hazard measurements. f. Controls and maintains the service area RFI Monitoring Van(s) (RFIM Van). 305. thru 399. RESERVED.

Page 31 (thru 32)

07_Chap 04_6050.32B_111705.pdf › CHAPTER 4. SPECTRUM MANAGEMENT EVALUATION CRITERIA

11/17/05 6050.32B

CHAPTER 4. SPECTRUM MANAGEMENT EVALUATION CRITERIA 400. GENERAL. This chapter provides the evaluation criteria to measure the field level spectrum management function effectiveness. 401. CRITERIA. The service area spectrum management function evaluations shall be conducted in accordance with the latest edition of Order 1800.14, Airway Facilities Evaluation Program. 402. SUBJECTS OF EVALUATION. The FAA service area spectrum management office performance shall be measured against the following evaluation criteria. a. Compliance With Standards and Guidelines. Service area spectrum management personnel shall be familiar with and strictly apply as appropriate, ITU, ICAO, FCC, NTIA and FAA published regulations governing frequency matters. b. Efficiency and Economy. (1) Personnel functions shall be defined by workload description statements, which accurately define the work performed by the FMO, that accompany the generic position descriptions. (2) Cross-training shall be accomplished to provide essential coverage of specialized areas.

(3) Economy of personnel and material shall be pursued actively in all operational phases. c. Spectrum Engineering. (1) Frequencies shall be engineered properly (prior to formal assignment) with respect to radiation, propagation, emission and power factors, including engineering consideration of protection from potential interference. (2) The FMO shall be the focal point and provide guidance and expertise in frequency matters to all service area elements. (3) Guidance shall be provided to the service area’s planning elements in advance of programming actions concerning the spectrum bands to be used, radiated power and emission characteristics of the new facilities and any limitations which appear because of legal or technical restrictions. Likewise, timely spectrum engineering guidance shall be provided to non-Federal entities, other Federal agencies and DOD elements desiring to establish aeronautical systems.

(4) Service area radiating systems shall be evaluated periodically, consistent with established review plans, for compliance with emission and performance standards, with deviations and recommendations reported for correction. (5) The FMO will coordinate with DOD organizations within their service areas as necessary, to ensure that electronic attack activity (including chaff operations, electronic jamming, etc.), does not impact the NAS. (6) Airspace cases will be analyzed in such a manner as to ensure that non-Federal users do not cause interference to critical aeronautical facilities.

6050.32B Chapter 4 - continued 11/17/05

(7) The FMO shall conduct electromagnetic compatibility studies, as necessary, to determine the effect of proposed systems on current NAS systems. (8) The FMO should participate in the site selection and installation planning for all new NAS facilities and systems. (9) The FMO should visit service area centers and TRACONs periodically in order to review requirements for radio spectrum to support NAS operations. d. Interference resolution. (1) Frequency interference problems to the NAS from any source shall receive priority attention and be corrected in minimum time. (2) Close working relationships shall be established with other agency elements in Technical Operations Services, Enroute and Oceanic Services, Terminal Services, Flight Standards (FS), and Airports, as well as local FCC and DOD frequency personnel, to assure rapid correction of interference problems. (3) Every effort shall be made to terminate or correct an interfering device in lieu of a frequency change to solve a problem.

(4) Appropriate data on incidents shall be entered into the RFI data base and engineering reports shall be prepared, describing problems, their resolution and recommendations regarding action to be taken to preclude recurrence. Copies of the reports shall be furnished to all entities involved and Technical Operations ATC Spectrum Engineering Services. (5) FMO offices shall have operable mobile and portable electronic interference detection equipment in addition to an RFIM van. Calibration shall be maintained for all critical equipment. e. Frequency assignment records. (1) The Government Master File (GMF) shall be kept current. (2) Frequency utilization shall be reviewed periodically, consistent with established review plans. The reports on the reviews shall include followup actions taken. (3) Frequency Transmitting Authorizations (FTA) for all FAA transmitters shall be issued by the FMO to the appropriate FAA authority for posting. When visiting a facility, the FMO should review the FTA for posting and accuracy.

(4) Procedures shall be established that use the available automated capabilities to determine quickly the status of all frequency assignment actions. (5) Filing procedures shall be established to assure rapid retrieval of correspondence and record information. f. Planning. (1) Arrangements shall be made to assure that FMOs receive information regarding frequency requirements for new facilities as soon as known, to assure the availability of frequencies.

11/17/05 Chapter 4 - continued 6050.32B

Page 35 (thru 40)

(2) FMO staff members shall maintain awareness of new system developments and techniques to provide information to planning offices. (3) Frequency assignment shall be obtained in time to enable installation personnel to order necessary crystals, filters, etc., prior to scheduled installations. (4) Maintain an awareness of the current status of projects to ensure that frequency records are kept updated. g. Coordination. (1) Channels of communication shall be established and maintained with appropriate military representatives and offices, FCC district and monitoring offices, other Federal spectrum users, interference resolution organizations and representatives of non-Federal aviation industry spectrum users. (2) Other FAA entities, such as Enroute and Oceanic Services, Terminal Services, FS, and non- Fed Coordinator shall be apprised of FMO functions and capabilities. (3) Coordination requirements for frequency matters in ITU, IRAC, ICAO and FCC regulations and procedures shall be adhered to.

(4) Procedures shall be established and maintained to assure close coordination with adjacent service areas. h. Radiation Hazard Survey. The FMO is the single point-of-contact in the service area for performing designated radiation hazard measurements, both ionizing and non-ionizing, and is responsible for the definitive measurements of radiation levels. (See Chapter 16). (1) FMOs shall conduct radiation hazard measurements and prepare reports as required. (2) Technical Operations ATC Facilities, Environmental, Energy Conservation, and Occupational Safety and Health (EEOSH) Services has overall program management responsibility for environmental hazards, including radiation hazards.

(3) In addition, the following functions are assigned to FMOs through Order 3900.19B: (a) Coordinate and consult with the Industrial Hygiene Program Manager in providing advice and information on matters pertaining to radiation health hazards in FAA operations. (b) Coordinate with the Industrial Hygiene Program Manager, the Industrial Investigations Program Manager and the Safety and Health Managers in responding promptly to reports of radiation health hazards. (c) Perform radiation health hazards surveys on new and modified facilities that house equipment, systems or substances capable of producing external ionizing or non-ionizing radiation fields, and others as required. 403. thru 499. RESERVED.

TOC3-final_ix-x 06-11-2019 (004) › 08_Chap 05_6050.32B_111705.pdf

11/17/05 6050.32B

CHAPTER 5. FREQUENCY COORDINATION 500. GENERAL. a. Any frequency assignment MUST be coordinated before it can be processed and authorized. The very nature of radio signal radiation makes it a candidate for interference to another frequency, thus all interested parties must be in agreement before a reliable frequency can be assured. There are five major areas of coordination within the FAA spectrum management function. They are headquarters, field-headquarters, field-external, field-special and field-internal. Each has its own requirements and peculiarities, thus requires separate explanation. b. As a general policy, only one frequency will be assigned for each individual requirement. For example, only one VHF A/G communications (COMM) frequency will be assigned for each Air Route Traffic Control Center (ARTCC) sector. Frequencies designated as "back-up" or "spare" are not authorized. 501. HEADQUARTERS.

All coordination with other Federal agencies, except as discussed in paragraphs 503 through 505, and any with foreign governments, is accomplished only by Technical Operations ATC Spectrum Engineering Services. Numerous coordination procedures have been developed for various frequency usages and are listed in the NTIA Manual of Regulations and Procedures for Federal Radio Frequency Management (NTIA Manual) in paragraph 8.3. This includes the east coast National Radio Quiet Zone (NRQZ). 502. FIELD-HEADQUARTERS. For new programs and systems, Technical Operations ATC Spectrum Engineering Services engineers may do the initial planning, engineering frequency applications. All routine aeronautical COMM, NAV and radar frequencies are engineered in the field and then forwarded to Technical Operations ATC Spectrum Engineering Services prior to being forwarded to Frequency Assignment Subcommittee for approval and eventual inclusion in the Government Master File. 503. FIELD-EXTERNAL.

In general, the FMO is urged to form a close working relationship with the field representatives of agencies with whom the FMO will work. A partial list of such agencies and the FMO's responsibilities are as follows: a. Inter-service area Work Force Support. Service areas can better adjust to peak workload conditions by establishing a seamless environment so that service areas can provide support to each other to accomplish functions as peaks occur. This inter-service area support would be provided at the request of the service areas needing the support. Headquarters may, in some cases, provide funding for this support. b. FCC Field Office. The FMO should become well acquainted with the Engineer in Charge of any FCC Field Office(s) in the FMO's service area. Interference dealing with a non-Federal transmitter will be coordinated with the local FCC. All communications with the local FCC representatives shall go through the regional FMO. c. DOD AFC. DOD has established AFCs within designated areas of the United States and possessions.

These AFCs represent DOD in their respective areas and have coordination authority over all the military services in their areas. If any DOD AFC has area encompassing any of the FMO's service area, it is imperative that the FMO become well acquainted with the AFC, since all military frequency coordination with FAA within the AFC's area of responsibility will be with the DOD AFC. See NTIA Manual, Chapter 8 and Annex D, for areas of responsibility, contacts, and telephone numbers. d. Military AFCs. The three main military departments, Army, Navy and Air Force, have their own service coordinators. Each service has a specific area of influence and each area is spelled out in the NTIA Manual,

6050.32B Chapter 5 – continued 11/17/05

Annex D. Just as with the DOD AFCs, it is important that the FMO become acquainted with these officials whose control areas are within the various service areas. e. United States Forest Service (USFS) and Bureau of Land Management (BLM). The person who has frequency coordination responsibility in USFS and the BLM in each service area is one that each FMO should know. In those service areas where forest fires are a problem, requests will be coming in at odd times for VHF COMM frequencies to use for the duration of a fire for communication with water-drop aircraft. Knowing the contact in advance is a great time saver. f. Search and Rescue (SAR) Groups. There are a large number of SAR groups in the country. Most are state or municipal governments, but a few are citizens groups who are interested in volunteering in searches for lost or downed aircraft. They are the ones who will request temporary frequency authorizations for Emergency Locator Transmitter (ELT) tests. g. Local Aviation Groups.

Local aviation groups are a source of information and frequently come to the FMO for assistance with new frequency requirements. For instance, an airport owner wanting a new Aeronautical Advisory Station (Unicom) frequency will come to the FMO. In addition, these groups have a lot of general information that can benefit the FMO. Included in this category are AOPA, ATA, Civil Air Patrol (CAP) and similar organizations. h. Other Federal Agencies. It is to the advantage of the FMO to be involved with other Federal agencies in the service area that use the radio spectrum. A good working relationship with other agencies is to the benefit of all. When another Federal agency causes interference to FAA frequencies, contact with the local agency’s technical personnel will bring much faster resolution to the problem than trying to resolve the problem at the national level. 504. FIELD-SPECIAL. The FMO may receive special requests not covered by the normal processes.

In such cases, the FMO must take particular care in fulfilling them and should consider all parameters before acting or referring to headquarters. When action is taken, Technical Operations ATC Spectrum Engineering Services shall be notified promptly if the FMO has taken or is contemplating taking action. Some of these actions are: a. ELT Tests. Various SAR groups wish to train their pilots at periodic intervals. To do so, they use an ELT, hidden by one of their group in some relatively remote area to test how long it takes for the pilots to locate it from the air, using whatever direction-finding equipment or techniques they have at their disposal. Refer to subparagraphs (1) and (2) below for the procedure on how to accommodate these requests. (1) The ELT test frequency is 121.775 MHz, as specified in Advisory Circular 91-44. Training SHALL NOT be conducted on 121.5 MHz or 243.0 MHz.

(2) When a group wishes to conduct ELT training, they shall contact the FMO and provide the following information: (a) Date and time of the test. (b) Site coordinates. (c) Organization name and the name of a responsible person in the organization. (d) A telephone number will be attended during the entire ELT test so that in the event of emergency or unacceptable interference, the test can be terminated quickly.

11/17/05 Chapter 5 - continued 6050.32B

b. Forest Firefighting Frequencies. USFS and BLM have interagency agreements with FAA for temporary use of A/G COMM frequencies to communicate with water-dropping aircraft during a forest fire. Some states also have firefighting aircraft and may contact FAA. The detailed procedure is left to the individual FMO. It is not uncommon for the firefighting agency to call the FAA duty officer Sunday midnight (or other inconvenient hours) requesting FAA permission to use a VHF COMM frequency. In addition, it is FAA's responsibility to publish the firefighting director's contact frequency in the NOTAM that establishes the temporary flight restrictions (TFR) for firefighting operations. This is to allow media aircraft access to the area to collect news information. (1) The fire services have proved beyond a doubt that the first 15 minutes of a fire determines whether it can be controlled promptly. The FMO should have a list of available frequencies at ready access, which means that the FMO and staff engineers will have them at home, too.

The requesting agency should be advised at the time of authorization to call the FMO or the duty officer as soon as the frequency is no longer needed. (2) The FMO shall forward a completed frequency assignment to Technical Operations ATC Spectrum Engineering Services, and may notify Technical Operations ATC Spectrum Engineering Services by phone of any frequency use that has been authorized. c. Fly-ins. Various groups request Terminal Services to provide a temporary control tower for special events of usually one to three days duration. To do that, Terminal Services must be provided with frequencies for the temporary tower or other requirements. On occasion, this might be a UHF frequency, if military aircraft are involved. Mostly, however, the request from Terminal Services will ask for a local control and a ground control frequency. The frequency 123.1 MHz may be used for a tempo control tower when coordinated with SAR, if air safety considerations are met.

(1) Initial contact between the aviation event sponsor and the FAA is normally with either the Flight Standards District Office (FSDO) or Area Director of Terminal Operations for the geographic service area of concern at least 45 days prior to the event. If temporary use of frequencies for control of the event's air traffic is needed, or if the assigned frequencies at the air show's location will be used differently than presently authorized, the Area Director of Terminal Operations for the geographic service area of concern or Flight Standards Field Office (FSFO), as appropriate, will contact the service area FMO for advice, or the sponsor may contact the service area FMO directly. (2) The aviation event sponsor may have proposed frequencies desired for use, for example, either FCC-controlled frequencies in the 122.8-123.0 MHz band for non-FAA use (UNICOM), (MULTICOM) or specific FAA air traffic control frequencies.

The FMO will advise the aviation event sponsor whether the proposed frequencies are acceptable and whether the frequencies being proposed are too congested to allow proper control of the aviation event. If the sponsor has no recommended frequencies or has chosen frequencies which are not acceptable to the FAA, then the FMO will advise the FSFO with a service area coordination number [for an example, see subparagraph (3)] and temporary frequencies, as needed. (3) A coordination number (for example, GL T030043) will be provided to the event sponsor for each frequency which is coordinated for the event use. The FMO will enter the temporary frequencies into the automated frequency management system to document their use. The frequency assignment will include both start and stop dates for the new assignment. (4) The FMO will forward a memorandum to the aviation event sponsor noting the coordination and frequencies to be proposed to the FCC for use. A courtesy copy of this document will be provided to Technical Operations ATC Spectrum Engineering Services.

An example of such a memorandum is shown in Figure 5-1.

6050.32B Chapter 5 – continued 11/17/05

FIGURE 5-1. SAMPLE MEMORANDUM TO AVIATION EVENT SPONSOR Subject: Coordination of Frequencies for Special Aeronautical Events From: Service Area Frequency Management Office To: Aviation Special Event Sponsor As coordinated on (date), this office has no objections to your use of the following frequency for use at (name) air show. The following applies: Frequency Coordinated: Power/Emission: Description of Antenna: Location of Transmitter (include geographical coordinates): Class of Station: Dates/Times to be Used: FAA Service Area Coordination Number: In order to obtain Special Temporary Authority to use this frequency, you must submit a request to the Federal Communications Commission (FCC) via the FCC internet address (currently http://wireless.fcc.gov/), and follow the directions under “online filing”, in order for them to review your application. Please cite the above FAA Service Area Coordination Number on your application documents to expedite FCC processing. Please contact (name) at FAA (Service Area) Frequency Management Office, (telephone), if you have further questions. (Signature)

cc: Area Director of Terminal Operations; Service Area Non-Fed Coordinator; HQ FAA/Technical Operations ATC Spectrum Engineering Services

11/17/05 Chapter 5 - continued 6050.32B

(5) After coordination with the FAA service area FMO, the sponsor will be expected to submit all required forms and fees to the FCC for a special temporary authority (STA) for use of the coordinated frequencies as required by the FCC rules. The sponsor may do this either by letter, telegram, fax or e-mail. (6) Upon receipt of the memorandum from the service area, Technical Operations ATC Spectrum Engineering Services will coordinate with the FCC and, in addition, will forward a memorandum to the FCC Licensing Division, Gettysburg, Pennsylvania, noting the FAA service area coordination number and stating that FAA has no objection to the temporary use of the frequencies for the aviation event. (7) In most cases, the FCC will issue the STA to the sponsor no later than 15 days prior to the event provided that all required forms and fees are received at their office within 30 days of the event. d. Non-Federal Requirements. (1) FCC licenses all non-Federal NAVAID and air-to-ground (A/G) COMM facilities.

The owner or sponsor of the facility must obtain airspace and frequency approval by FAA while processing the application for a transmitting license through FCC. The following is the order of priority for assigning frequencies to non-Federal facilities after airspace approval has been granted. (a) Public use airport tower or NAVAID providing Instrument Flight Rules (IFR) service. (b) Private use airport tower or NAVAID providing IFR service. (c) Public or private use Visual Flight Rules (VFR) or en route advisory service. (2) FAA must advise sponsors in subparagraph (c) above that frequency assignments can be taken away from the facility with a one year notice to satisfy a more critical requirement. The sponsor must also be advised that, if frequency changes are required to assign a channel to the facility, the sponsor must reimburse FAA for the cost of the changes. (3) Non-Federal NAVAIDs must be in the NAS. If it is to be private, the applicant shall be advised that a proposed frequency will be engineered if possible.

However, since it is not in the NAS, it is subject to withdrawal for a NAS facility, if the frequency is required at a later date. Lastly, the applicant must be advised in writing that if a frequency is engineered, it will be reserved for only one year. After that, it will be withdrawn if not used. Extensions can be given only upon a showing of definite progress in procuring FCC license and equipment delivery. Flight Standards has to concur with the request. If the NAVAID is a Compass Locator (COMLO), the power limit is 25 watts (W). If a VOR or ILS, the power and service volume will be of terminal class. (4) If a COMM frequency, it also is reserved for only one year. The power limit shall be 10 W. (5) Equipment shall be FCC type-approved and the applicant shall be so advised. (6) Licenses for Non-Federal radio navigation aids. (a) Proponent actions: 1. The proponent fills out an FAA Form 7460-1 and submits it to the appropriate service area Non-Fed Coordinator.

6050.32B Chapter 5 – continued 11/17/05

2. At the same time, the proponent submits an FCC Form 406 (Application for License) to the FCC Licensing Division at Gettysburg, Pennsylvania. (b) Service area actions: 1. Upon receipt of the FAA Form 7460-1 from the proponent, the FAA service area Non-Fed Coordinator will forward the request to Air Traffic Organization System Operations Services. 2. Air Traffic Organization System Operations Services will initiate an airspace case (as needed) and register the proponent with Aeronautical Information Management (AIM) in System Operations Airspace and AIM. 3. Air Traffic Organization System Operations Services returns the FAA Form 7460-1 to the service area Non-Fed Coordinator who then submits the form to the service area FMO. 4. The Service Area FMO engineers the appropriate frequency, prepares a temporary frequency application and forwards it to FAA Headquarters. At the same time, the FMO also extracts the applicable information from the FAA Form 7460-1 to prepare a memorandum to the FCC indicating the status of the proponent's request. (c) FCC actions: 1.

The FCC Licensing Division receives the FCC memorandum, logs it for tracking purposes and forwards it to FCC Headquarters. 2. FCC Headquarters processes the memorandum and forwards it to FAA Headquarters. (d) FAA Headquarters actions; 1. FAA engineers and selects a frequency to satisfy the requirement (based on the temporary frequency assigned by the service area FMO) and forwards the application to NTIA for approval. 2. FAA electronically forwards a copy of the FCC memorandum, with the coordinated frequency, to FCC Headquarters. 3. When the frequency application is approved by NTIA, the FCC Licensing Division issues the license to the proponent. e. Electronic Attack (EA) Missions. EA missions are military exercises whereby electromagnetic signals are radiated intentionally to cause interference to other military units being tested for EA defense. See chapter 18 for a detailed discussion. f. Unusual Request. Unusual requests will be received from time to time, and there is no way to cover them all here.

When not covered by specific instructions herein or by headquarters directive, all requests for unusual needs should be telephoned or faxed to Technical Operations ATC Spectrum Engineering Services. 505. FIELD-INTERNAL. All of the foregoing paragraphs in this chapter have dealt mostly with coordination outside the service area office. But coordination within the service area office is as essential as outside. The style of frequency coordination will vary with the service area because of the various configurations of the spectrum management functions. At least the following shall be included:

11/17/05 Chapter 5 - continued 6050.32B

a. Air Traffic. Except for a few land mobile system needs, all frequencies engineered are to meet an air traffic service need. Thus the FMO must coordinate closely with Enroute and Oceanic Services, and Terminal Services, personnel as appropriate. This is not only to meet the current need, but also to be aware of service planning so that efficient spectrum usage in the future may be taken into account. b. Flight Standards. The same logic applies here, particularly as it relates to NAVAIDs. But if FS needs to change a route or vector, an Expanded Service Volume (ESV) or even a new NAVAID may be required. Frequent meetings with FS personnel are recommended. c. New requirements for COMM, NAVAID, and radar facilities. Attendance at program review meetings within the Service Area office and at System Management Offices (SMO) by the FMO is essential to provide as much advance notice as possible of new facilities and programs to permit advanced planning. d. Adjacent Service Areas. FMOs should coordinate frequently with their counterparts in adjacent service areas.

This is particularly important when a planned facility's interference range infringes upon an adjacent service area’s territory. When a frequency request is filed with Technical Operations ATC Spectrum Engineering Services, it is assumed that the FMO has coordinated with any affected adjacent service areas. 506. DOCUMENTATION. The FMO is required to have many sources of documentation in order to effectively coordinate. At least the orders and documents listed in subparagraphs a.- u. below, as applicable, shall be maintained by the FMO. a. NTIA Manual Of Regulations and Procedures For Federal Radio Frequency Management. b. FCC Rules and Regulations. c. ICAO Annex 10. d. Government Master File on CD-ROM e. FCC Aeronautical Frequency List (see CFR 47, Part 87 -- Aviation Services). f. The Daily National Automated Performance Reporting System (NAPRS) data report. g. Aeronautical Information Manual. h. ITU Radio Regulations. i. Military Joint ECM Regulation, CJCSI, Performing Electronic Warfare in the United States and Canada. j.

The latest edition of Order 7610.4, Special Military Operations. k. The latest edition of Order 7400.2, Procedures for Handling Airspace Matters. m Federal Aviation Act of 1958, revised April 1981. n. The latest edition of the Federal Aviation Regulations, Part 77. o. The latest edition of Order 7350.6, Locations Identifier Handbook.

6050.32B Chapter 5 – continued 11/17/05

p. The latest edition of Order 1380.40, Airway Facilities SMO Level Staffing Standard System. q. Sectional Aeronautical Charts. r. VFR Terminal Area Charts. s. Airport Facility Directory. t. U. S. Terminal Procedures. u. DOD Flight Information publications. 507. thru 599. RESERVED.

Page 48 (thru 52)

TOC3-final_ix-x 06-11-2019 (004) › 09_Chap 06_6050.32B_111705.pdf

11/17/05 6050.32B

CHAPTER 6. TRANSMITTING AUTHORIZATION DOCUMENTS

AND CALL LETTER ASSIGNMENTS

600. PURPOSE. This chapter describes the procedures for issuing and posting transmitter authorization documents and the guidelines for assigning call signs to all transmitters. 601. FACILITY TRANSMITTING AUTHORIZATION DOCUMENT (FTA). All transmitters authorized must have appropriate documentation posted for identification and certification purposes. In FAA, there are two basic forms, a certificate style and a metallic label. a. For all fixed, base, and land transmitters, the certificate is used. Currently, it is FAA Form 6050-1, Facility Transmitting Authorization. See figure 6-1. (1) Each facility shall have its own document and its unique document number for file purposes. The number shall consist of two letters identifying the service area, followed by a number. The letters and numbers will remain for that site as long as the site exists.

Whenever there are modifications to any assignment at that facility, a new document shall be issued, with an added letter starting with "A." When the assignments are subsequently modified, documents will contain sequential sub-letters, "B," "C," etc. until "Z." After "Z," the letter will start again at "A." The original document shall be posted at the site. (2) The Automated Frequency Management program (AFM) now in use for frequency request/authorization will generate one FTA for each facility. This program will contain a database of all FTA's issued. (3) Emission designators for major FAA systems can be found in the appendix. b. For all mobile transmitters, the identification label, FAA Form 6050-2, Transmitter Identification and Operation Authorization (TIOA), shall be used. For hand held transceivers, either the Form 6050-2 or a smaller equivalent may be used. The call letters of the unit will by typed or inked on it before applying to the transmitter.

Because the metallic labels stick very firmly, any changes in call letters should be accomplished by placing the replacement label directly over the old one. The procedure for assignment of call letters will be covered later. If the unit is transferred to a different organization or shipped to the FAA Depot for exchange and repair, a new identification label will be issued. A sample of both TIOA forms is shown in figure 6-2.

6050.32B Chapter 6 – continued 11/17/05

FIGURE 6-1. FAA FORM 6050-1, FACILITY TRANSMITTING AUTHORIZATION (REDUCED)

FIGURE 6-2. TIOA FORM FOR MOBILE/PORTABLE/HANDHELD TRANSMITTERS

11/17/05 Chapter 6 - continued 6050.32B

602. REQUESTS FOR FREQUENCY ACTION. Frequency requests from entities within the service area hould be standardized for record purposes. This will assure the FMO receives all the information needed with

e request. A sample service area form is shown in figure 6-3.

RE 6-3. SAMPLE OF TYPICAL SERVICE AREA FREQUENCY REQUEST FORM (REDUCED)

s th

FIGU

6050.32B Chapter 6 – continued 11/17/05

03. CALL LETTER ASSIGNMENT. All transmitters that are in use shall be identified by assigned call tters to meet international requirements, to help users know with whom they are communicating and to identify ignals in case of interference.

a. Most NAVAIDS are identified in accordance with Order 7350.6, Location Identifier Handbook.

b. Communications facilities are voice identified by facility; e.g., "Denver Tower," "Kansas City Center," tc.

c. HF, VHF, and UHF non-aeronautical service voice transmitters are identified by standardized lpha-numeric call signs. They are the systems described in Chapter 17, Land Mobile and Other FM

ommunications Systems Frequency Engineering.

(1) HF call signs will be issued by Technical Operations ATC Spectrum Engineering Services in ccordance with the standard operating procedure "Procedure for Assigning Call Signs," a policy letter to the ervice areas.

(2) VHF/UHF Land Mobile call systems shall be managed and issued by the FMO in accordance with aragraphs 604 and 605.

04. LAND MOBILE CALL SIGNS. Land mobile call signs shall be formulated and assigned in accordance ith subparagraphs a. through e., below.

a. FM Repeater stations call signs shall consist of the prefix "FAA" followed by the repeater's three- or ur-character facility identifier, as shown in the Facility Master File (FMF).

b. FM Base, Mobile, and Portable transmitters call signs shall consist of the most commonly recognized rea identifier where the station is located, followed by a user identifier issued according to figure 6-4.

c. Stations located at a service area office use the service area identifier. Special organizations will be entified as follows:

Washington Headquarters AHQ

Metropolitan Wash. Airports MWA

FAA William J. Hughes ACT Technical Center

Mike Monroney AAC Aeronautical Center

6 le s e a C a s p 6 w fo a id

11/17/05 Chapter 6 - continued 6050.32B

ORGANIZATION IDENTIFIERS

on headquarters, FAA William J. Huges Technical Center, Mike Monroney

100-199

200-299

d. An alphabetic character following the user identifier will identify the station type thus:

B - Base station

Continue reading ↓ 120 of 706 passages shown