Radar Vectors
FAA Order Current Issued Dec 4, 1974 AJW-183 7 pages Copy saved Nov 18, 2026

Order 4650.20A Reporting and Replacement of Items Failing Under Warranty

Official source ↗ Open PDF

Text read by OCR from a scanned file. Check the original, as some words may be misread.

ORDER DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION 4650.20A

ORDER DEPARTMENT OF TRANSPORTATION FEDERAL AVIATION ADMINISTRATION 4650.20A

12/4/74

SUBJ: REPORTING AND REPLACEMENT OF ITEMS FAILING UNDER WARRANTY

1. PURPOSE. This order revises existing procedures for recording warranty information and the reporting and replacement of items failing under warranty.

SUBJ: REPORTING AND REPLACEMENT OF ITEMS FAILING UNDER WARRANTY

2. DISTRIBUTION. This order is distributed to branch level in the Logistics, Airway Facilities and Systems Research and Development Services in FAA headquarters; section level in the Logistics and Airway Facilities Divisions in the regions; branch level in the FAA Depot and Aeronautical Centcr Procurement Division; twenty-five copies to NAfEC Logistics Division and minimum distribution to all field offices and facilities.

3. GANCELLATION. Order 4650.20, Reporting and Replacement of items failing under warranty, dated March 21, 1974, is cancelled.

4. BACKGROUND. Order, IM 4250.6, established responsibilities and guidelines for the reporting of items failing under warranty and the related supply support processes, but was not distributed below regional office level. This revised order recognizes office designation changes due to regional reorganizations and provides uniform field procedures for failure reporting.

5. SCOPE. The provisions of this order are applicable to all non-aircraft equipment and supply items purchased by an FAA procurement office and those acquired from the FAA Depot that are covered by a manufacturer's warranty.

The FAA Depot processes for warranty program management and documentation are covered in Chapter 10 of AC Order 4650.1, FAA Depot Matericl Management Handbook.

6. WARRANTY DATA. The method of recording/maintaining warranty records will vary depending upon the acquisition source and the types of items involved.

a. Eguipment.

(1) Field offices shall maintain the following information for each piece of equipment received that is covered by warranty.

Distribution: WAF/LG/RD-3; RAF/LG-4; CDE/CPR-3; Initiated By: ALG-110 NLG-50(25 cys); FOF-0 (minimim)

4650.20A 12/4/74

Date Accepted Date Installed Date Warranty Expires Contract/P.O, Number

(2) Contracts issued by the Logistics Service Contracts Division normally require that each contractor affix a stamp with the above elements to each piece of equipment. The "Date Accepted" reflects final government acceptance, origin or destination, as applicable, and field installation personnel shall enter "Date Installed" and "Date Warranty Expires."

The "Date Installed" is the date the equipment was initially energized at the field facility in the case of installation by FAA personnel. In the case of contract installation (turn-key), it is the date installation is accepted by FAA.

b. Supplies. Supply items which are covered by warranty will be identified by the contractor, as specified by the contract, by information affixed to the item or container. In those instances where warranty data is on the container, records shall be prepared as specified in Paragraph 6a(1) to insure data availability if the container is lost or destroyed.

Although the majority of supply items are not covered by warranty, several types of items, both Depot and Region support, are customarily covered. These include, but are not limited to:

(1) Electric motors, transformers, relays and compressors.

(2) Electron tubes.

(3) Circuit boards or components thereof.

7. FAILURE REPORTING.

a. Nationally Furnished Items. When a nationally furnished item (Washington or FAA Depot Acquisition) fails within the warranty period, it shall be reported by the Airway Facilities Technican or Field Logistics Specialist, as applicable, to the FAA Depot (AAC-485) within five days after failure. Maintenance action shall be limited to replacement except in emergancy situations where repair is necessary to ayoid an outage.

(1) Sector personnel shall prepare and submit a completed FAA Form 4650-10, Warranty Failure Report (App. 1) for each equipment or supply item failing during the contract or order warranty period, in accordance with the instructions contained on the reverse side of the form. With respect to Block 26, Failure Narrative, describe

Page 2 Par 6

12/4/74 4650.20A

in narrative form the conditions prior to, at the time of, and subsequent to the failure. This narrative must also explain cause of failure, what was done to effect repairs, assistance in repairing, and any suggestions to prevent such failures. The determination, as to whether the failed part is replaceable under the warranty, is based on such narrative.

(2) The F & E Installation Technican shall provide sector personnel all data necessary to prepare Warranty Failure Reports for all warranty items failing during installation/test prior to commissioning.

(3) The distribution of FAA Form 4650-10, Warranty Failure Report, shall be as follows:

FAA Depot (AAC-485) - original and first two copies Regional Logistics Division - one copy Washington, ALG-400 - one copy Facility - one copy

b. Locally (Region) Furnished Items. The "warranty" failure of a locally furnished item, equipment or supply, shall be reported to the procuring office by letter or telephone if an adjustment cannot be worked out by the field office through a local authorized manufacturer's representative.

c. Failure Report Number (3 Positions). Sequential numbers, used as a suffix to the facility supply support code shall serve as failure report numbers. The numbering sequence should be constructed to differentiate between failure reports for nationally furnished and locally furnished items. FAA Form 4650-l0 should not be used to report failures of locally furnished items.

8. SUPPLY SUPPORT. The submission of FAA Form 4650-10 to thc FAA Depot does not constitute a requisition action for a replacement item. Replacement items shall be acquired in accordance with the provisions of FAA Order 4650.12A, Local Purchase, Paragraph 6 and FAA Order 4250.9, Field Inventory Management and Replenishment, Chapters 2 and 4. Requisitions placed on the FAA Depot for warranty item failure replacement shall be identified as such and shall reference the failure report number.

9. DISPOSITION OF DEFECTIVE ITEMS. Items, equipment or supply, failing under warranty, except thosc locally furnished items satisfactorily adjusted by a manufacturer's representative, shall be retained pending disposition instructions from the Depot or regional procurement office.

25

Par 7 Page 3

4650.20A 12/4/74

If disposition instructions are not received within 90 days, a Speed Memo, with enclosed copy of the failure report, shall be forwarded to the applicable office as a follow-up. If disposition instructions are not received within the following 30 days (120 days total) the item may be disposed of in accordance with the provisions of FAA Order 4800.2, Utilization and Disposal of Excess and Surplus Property.

When disposition instructions specify shipment of a defective unit to the manufacturer or elsewhere, the shipment shall be supported by FAA Form 1660 Requisition/Invoice (App. 2). Distribution of FAA Form 1660 is as follows:

Parts 1 & 2 Consignee (with failure report) Part 3 (nationally furnished item) AAC-485 Part 3 (locally furnished item) Region Procurement Part 4 Region Logistics Division (ref. failure no.) Part 5 Logistics Service (ALG-400) Part 6 Retain for future reference.

*10. FORMS AVAILABILITY. FAA Form 4650-10 Warranty Failure Report is available from the FAA Depot under NSN:0052-00-030-5002, unit of issue - (pads).

R. F. FRAKES Director, Logistics Service

Page 4 Par 9

12/4/74 4650.20A Appendix 1

RIS: LG 4250.3 PARTMENT OF TRANSPORTATION DATE OF REPORT CONTROL NUMBER (DEPOT USEI DERAL AVIATION ADMINISTRATION WARRANTY FÁILURE REPORT PART I - FACILITY DATA PART II - EQUIPMENT DATA 1. Facility Report No. 6. Name (System/Facility) 7. FA Type No.

2. Region Logistics Specialist 3. Phone 8. Manufacturer 9. Serial No. FTS : Comm: 10. Date Received I1. Date Operative 4. Facility Address 12. Date Failed 13. Date Warranty Exp.

14. Contract/Order No. (Equipment) 5. Contract No./Order No. (Applicable to failed items)

PART III - FAILED COMPONENT DATA (Above Equipment On/y) 15. Part No. 16. Noun 17.. Manufacturer 18. Serial No. 19. Ref: Designation 1 T 20. National Stock No. 21. Qty. 22. Date Operative 23. Date Failed 24. Date Warranty Exp.

EM 25. Replace. Rqn. from Depot? 26. Failure Narrative - Hours Operation

N RQN# : 0. DATE PRI NO WHY

N RQN# : 0. DATE PRI NO WHY

15. Part No. 16. Noun 17. Manufacturer 18. Serial No. 19. Ref. Designation

20. National Stock No. 21. Qty. 22. Date Operative 23. Date Failed 24. Date Warranty Exp.

M 25. Replace. Ran. from Depot? 26. Failure Narrative - Hours Operation N RQN# : 0. DATE PRI NO_ WHY

15. Part No. 16. Noun 17. Manufacturer 18. Serial No. 19. Ref. Designation 1 TE 20. National Stock No. 21. Qty. 22. Date Operative 23. Date Failed 24. Date Warranty Exp.

M 25. Replace, Rqn. from Depot? 26. Failure Narrative - Hours Operation N RQN# : 0. DATE PRI NO_ WHY

15. Part No. 16. Noun 17. Manufacturer 18. Serial No. 19. Ref. Designation 1 T 20. National Stock No. 21. Qty. 22. Date Operative 23. Date Failed 24. Date Warranty Exp.

25. Replace. Rqn. trom Depot? 26. Failure Narrative - Hours Operation N RQN# 0. DATE PRI NOI WHY FAA Form 4650-10 (4-74) SUPERSEDES FAA FORM 419

4650.20A Apendix 1 12/4/74

PREPARATION INSTRUCTIONS

PREPARATION INSTRUCTIONS

PART I - FACILITY DATA 1. Supply Support code and three position numeric suffix 2. thru 5. Self explanatory

PART II – EQUIPMENT DATA 6. Complete alpha name of Facility 7. FA designation 8. Equipment manufacturer 9. thru 14. Self explanatory

PART III – FAILED COMPONENT DATA (identify each item no, by A, B, etc.) 15. Manufacturer's part number (instruction book) 16. thru 19. Self explanatory 20. National Stock Number - replaces Federal Stock Number 21. Quantity failed 22. thru 24. Self explanatory 25. Cite requisition number, date and priority if replacement item was requested from the FAA Depot. 1f not, why? 26. Narrative - continue on additional sheet if necessary

NOTE: If five or more different items are to be reported for the same equipment and contract/ purchase order number, this form may be used as a continuation sheet. To insure proper identification, Blocks 1 and 5 must be filled in.

DISTRIBUTION INSTRUCTIONS FAA Depot - original and first two copies Regional Logistics Division - one copy Washington, ALG-400 - one copy Facility - one copy

12/4/74 4650.20A Appendix 2

ROUTING FEDERAL AVIATION AGENCY

REQUISITION INVOICE PREPARED BY PREPARED BY

Sirnature Pouting Symhol REQ'N OUTGOING NO. INCOMING NO. NO'S Document Ct1 Nunher

DATE DATE X DATE SIGNATURE METHOD OF SHIPMENT CARRIERS (INCLUDE FINAL CARRIER, IF KNOWN)

GOVT B/L NO. DATE SMIPPED TITLE APALS SIGNATURE TOTAL WEIGHT NUMBER OF PAČKAGES

REQUISITION INVOICE PREPARED BY PREPARED BY

TITLE X SHIP TO: (CONSIGNEE) FROM (CONSIGNOR) FAA, Office Street Address City. State ZIP

RELEASED BY MARK FOR: Signature TITLE x

ITEM NO. CATALOG NO. ITEM DESCRIPTION QUANTITY AND UNIT UNIT PRICE AMOUNT DOLLAR PACKAGE NO.

PETURN OF ITEM FAILING UNDEP WARPANTY

X x x X

((Peference Priority-Pequisition Numher and Tvne-FAA 4650-10 No & Date))

PETURN OF ITEM FAILING UNDEP WARPANTY

ACCOUNTING CLASSIFICATION AND CODES TOTAL AMOUNT APPROPRIATION AND LIMITATION DO NOT USE ALLOTMENT DISTRIBUTION PROJECT OR AMOUNT OF INVOICE

REIMBURSEMENT REQUIRED

NO DISTRIDUTION PLAN CERTIFICATION: I CERTIFY ALL ITEMS RECEIVED IN GOOD CONDITION. EXCEPT AS NOTED HEREON SIGNATURE TITLE DATE PAGE 1 OF PAGES