Order 3900.19B Occupational Safety and Health Program
This order establishes policy, delegates authority, and assigns broad responsibilities to ensure each FAA organization complies with the Occupational Safety and Health Act requirements and related regulations as noted within this document. This order is specific to OSH policy and protecting employees from injury and illness. This order is written in broad terms to address the entire FAA
This document is cancelled. Cancelled by 3900.19C. Check the official source before relying on it.
Text read by OCR from a scanned file (2 of 161 pages). Check the original, as some words may be misread.
Distribution: A-W(minus NS)-1; A-W(NS)-2; A-X(minus AT/FS/HR/AM/AF)-1; Initiated By:AEE-200 A-X(AT/FS/HR/AM)-2; A-X(AF)-3; A-Y(minus ES/HR)-1; A-Y(ES/HR)-2; A-Z(minus (FM/HR)-1; A-Z(FM/HR)-2; A-F0F-0 (LTD)
ORDER
3900.19B
FAA OCCUPATIONAL SAFETY AND HEALTH
PROGRAM
Originally issued April 29, 1999
FAA OCCUPATIONAL SAFETY AND HEALTH
Updated to include subsequent chapters March 8, 2006
DEPARTMENT OF TRANSPORTATION
FEDERAL AVIATION ADMINISTRATION
Foreword Page i (through ii)
FOREWORD
This order establishes the policy framework and assigns responsibility for an effective agencywide employee safety and health program. The goal of the program is to ensure that FAA employees are provided with places and conditions of employment that are free from recognized hazards that cause or are likely to cause death or serious physical harm.
FEDERAL AVIATION ADMINISTRATION
In accordance with the terms agreed to during the 1994 realignment of the FAA occupational safety and health program, detailed implementation guidance will be provided separately by the Airway Facilities Service to serve the day-to-day management and operation of the program.
This order plus AAF-generated implementation guidance are intended to meet the requirements established by the Occupational Safety and Health Act, which was passed by Congress on December 29, 1970. The FAA Administrator is required by law to establish and maintain an agencywide occupational safety and health program that is consistent with the legal requirements of Public Law 91-596, Occupational Safety and Health Act of 1970; Executive Order 12196, Occupational Safety and Health Programs for Federal Employees; 29 CFR Part 1960, Basic Program Elements for Federal Employee Occupational Safety and Health Programs; and DOT Order M 3902.7B, Occupational Safety and Health Management Manual.
It should be noted that some of the procedures contained within this order may appear to be implementation guidance (e.g., paragraph 901, Employee Report of Hazardous Condition). However, 29 CFR Part 1960 requires that certain basic programmatic procedures be incorporated into any Federal agency occupational health and safety program as policy. Such procedures were added in this document to meet the Federal requirements.
If problems arise that may not be sufficiently described in this order, consult the FAA Office of Environment and Energy for further assistance.
Table of Contents
TABLE OF CONTENTS CHAPTER 1 GENERAL 1-1 1. PURPOSE 1-1 2. DISTRIBUTION 1-1 3 CANCELLATIONS 1-1 4. BACKGROUND 1-1 5. EXPLANATION OF CHANGES 1-2 6. FORMS 1-2 7. AUTHORITY TO ISSUE CHANGES TO THIS ORDER 1-2 8. POLICY 1-2 9. STANDARDS 1-2 10. OCCUPATIONAL SAFETY AND HEALTH PROGRAM REQUIREMENTS 1-3 11. DEFINITIONS 1-4 12 RESPONSIBILITIES OF HEADQUARTERS OFFICES 1-5 13. RESPONSIBILITIES OF THE REGIONS AND CENTERS 1-9 14. RESPONSIBILITIES OF ALL FAA SUPERVISORS AND EMPLOYEES 1-11 CHAPTER 2 WORKPLACE INSPECTIONS, ABATEMENT PROGRAMS, AND VARIANCES 2-1 200. GENERAL 2-1 201. INSPECTION OF WORKPLACES 2-1 202. ABATEMENT OF UNSAFE AND UNHEALTHFUL CONDITIONS AND PRACTICES 2-2 203. VARIANCES 2-2 CHAPTER 3 SAFETY AND HEALTH ORGANIZATION 3-1 300. GENERAL ORGANIZATION 3-1 301. REGION/CENTER SAFETY AND HEALTH PROGRAM 3-1 302. POLICIES AND PROCEDURES 3-2 303. PLANNING AND DECISIONMAKING PROCESS 3-2 CHAPTER 4 PROFESSIONAL QUALIFICATIONS AND TRAINING OF OSH STAFF (RESERVED) CHAPTER 5 SAFETY AND HEALTH MANAGEMENT INFORMATION SYSTEM 5-1 500. GENERAL 5-1 501. MISHAP REPORTING 5-1 502. HAZARD REPORTING 5-1 503. SAFETY INFORMATION (OPTIONAL) 5-1 CHAPTER 6 OCCUPATIONAL SAFETY AND HEALTH TRAINING AND AWARENESS PROGRAM 6-1 600. GENERAL 6-1 601. MISHAP REPORTING 6-1 602. HAZARD REPORTING 6-1 603. SAFETY INFORMATION (OPTIONAL) 6-1 CHAPTER 7 MISHAP REPORTING AND INVESTIGATION 7-1 700. GENERAL 7-1 701. MISHAP INVESTIGATION 7-1 702. REPORTING OF OCCUPATIONAL INJURIES OR ILLNESSES 7-2 703. RECORDKEEPING 7-3 704. FATAL AND CATASTROPHIC ACCIDENTS 7-3 705. MOTOR VEHICLE MISHAPS 7-3
Table of Contents
706. OTHER MISHAPS 7-3 Figure 7-1 FAA FORM 3900-6, FAA MISHAP REPORT 7-4 Figure 7-2 FAA FORM 3900-6 DEFINITIONS TABLE 7-6 Figure 7-3 ACCIDENT INVESTIGATION CHECKLIST 7-11 CHAPTER 8 EVALUATION OF THE OSH PROGRAM (RESERVED) CHAPTER 9 REPORTS BY EMPLOYEES ON HAZARDOUS CONDITIONS 9-1 900. GENERAL 9-1 901. EMPLOYEE REPORT OF HAZARDOUS CONDITION 9-1 902. ALLEGATIONS OF REPRISAL 9-2 CHAPTER 10 FALL PROTECTION PROGRAM 10-1 1000. GENERAL 10-1 1001. SCOPE 10-1 1002. DEFINITIONS 10-1 1003. PROGRAM ELEMENTS 10-2 Figure 10-1. CROSS REFERENCES TO OSHA & NATIONAL CONSENSUS STANDARDS 10-5 Figure 10-2. FAA ELEVATED WORK SURFACE JOB CATEGORIES 10-7 CHAPTER 11 CONFINED SPACE ENTRY PROGRAM 11-1 1100. GENERAL 11-1 1101. SCOPE 11-1 1102. DEFINITIONS 11-1 1103. PROGRAM ELEMENTS 11-2 CHAPTER 12 OCCUPATIONAL MEDICAL SURVEILLANCE PROGRAM 12-1 1200. GENERAL 12-1 1201. BACKGROUND 12-1 1202. GOALS AND OBJECTIVES 12-1 1203. SCOPE 12-1 1204. DEFINITIONS 12-1 1205. KEY PROGRAM ELEMENTS 12-2 1206. NATIONAL OCCUPATIONAL MEDICINE SURVEILLANCE PROGRAM OVERSIGHT TEAM (NOMSPOT) 12-2 1207. RESPONSIBILITIES 12-3 Figure 12-1 EXAMPLES OF OSHA REGULATIONS THAT INCLUDE MEDICAL SURVEILLANCE REQUIREMENTS 12-6 CHAPTER 13 HAZARDOUS ENERGY CONTROL PROGRAM (LOCKOUT/TAGOUT) 13-1 1300. GENERAL 13-1 1301. SCOPE 13-1 1302. POLICY 13-1 1303. DEFINITIONS 13-1 1304. KEY PROGRAM ELEMENTS 13-2 CHAPTER 14 RADIATION SAFETY PROGRAM 14-1 1400. GENERAL 14-1 1401. BACKGROUND 14-1 1402. RELATED PUBLICATIONS 14-2 1403. GOALS AND OBJECTIVES 14-2 1404. SCOPE 14-2 1405. DEFINITIONS 14-3
Table of Contents
1406. KEY RADIATION SAFETY PROGRAM ELEMENTS 14-5 1407. NIR EMPLOYEE EXPOSURE CRITERIA 14-6 1408. IONIZING RADIATION EMPLOYEE EXPOSURE CRITERIA 14-6 1409. RADON EXPOSURE CRITERIA 14-7 1410. RESPONSIBILITIES 14-7 Figure 14-1 OSHA RESPONSE CONCERNING FAA’s ADOPTION OF CONSENSUS RADIATION SAFETY SANDARDS 14-11 Figure 14-2 INTERIM POLICY #AEE097-02, EVALUATION OF POTENTIAL RADIO FREQUENCY (RF) RADIATION HAZARD AT PLANNED AND EXISTING CHILD CARE CENTERS, DATED APRIL 21, 1997 14-13 CHAPTER 15 ASBESTOS CONTROL PROGRAM 15-1 1500. GENERAL 15-1 1501. BACKGROUND 15-1 1502. GOALS AND OBJECTIVES 15-1 1503. SCOPE 15-1 1504. STANDARDS 15-1 1505. DEFINITIONS 15-2 1506. KEY ASBESTOS CONTROL PROGRAM ELEMENTS 15-5 1507. ACRONYMS 15-11 Figure 15-1 POLICY MEMO #AEE09-01, MEDICAL SURVEILLANCE REQUIREMENTS FOR FAA EMPLOYEES FOLLOWING UNANTICIPATED, EPISODIC RELEASES OF ASBESTOS CONTAINING DUST, DATED DECEMBER 23, 1996 15-12 CHAPTER 16 THERMAL STRESS PREVENTION PROGRAM 1600. GENERAL 16-1 1601. BACKGROUND 16-1 1602. STANDARDS 16-1 1603. DEFINITIONS 16-2 1604. KEY PROGRAM ELEMENTS 16-3 CHAPTER 17 BLOODBORNE PATHOGENS CONTROL PROGRAM 1700. GENERAL 17-1 1701. BACKGROUND 17-1 1702. GOALS AND OBJECTIVES 17-1 1703. SCOPE 17-1 1704. DEFINITIONS 17-1 1705. KEY BLOODBORNE PATHOGENS PROGRAM ELEMENTS 17-2 CHAPTER 18 RESERVED CHAPTER 19 FAA HAZARD COMMUNICATION PROGRAM 1900. GENERAL 19-1 1901. BACKGROUND 19-1 1902. SCOPE 19-1 1903. GOALS AND OBJECTIVES 19-1 1904. DEFINITIONS 19-1 1905. KEY PROGRAM ELEMENTS 19-3 CHAPTER 20 RESPIRATORY PROTECTION PROGRAM 2000. GENERAL 20-1 2001. BACKGROUND 20-1 2002. SCOPE 20-1
Table of Contents
2003. GOALS AND OBJECTIVES 20-1 2004. DEFINITIONS 20-1 2004. DEFINITIONS (Continued) 20-2 2005. KEY RESPIRATIOR PROGRAM ELEMENTS 20-2 CHAPTER 21 HEARING CONSERVATION PROGRAM 2100. GENERAL 21-1 2101. BACKGROUND 21-1 2102. CANCELLATION 21-1 2103. SCOPE 21-1 2104. GOALS AND OBJECTIVES 21-1 2105. DEFINITIONS 21-1 2106. KEY PROGRAM ELEMENTS 21-3 Figure 21-1 PERMISSIBLE NOISE EXPOSURE 21-9 CHAPTER 22 FIRST AID PROGRAM 2200. GENERAL 22-1 2201. BACKGROUND 22-1 2202. SCOPE 22-1 2203. DEFINITIONS 22-1 2204. KEY FIRST AID PROGRAM ELEMENTS 22-1 POLICY MEMO #AEE002-01, CLARIFICATION OF ORDER 3900.19B, CHAPTER 22, FIRST AID CHAPTER 23 JOB HAZARD ANALYSIS 2300. PURPOSE 23-1 2301. BACKGROUND 23-1 2302. SCOPE 23-1 2303. GOALS AND OBJECTIVES 23-1 2304. TRAINING 23-1 2305. STEPS IN THE JHA PROCESS 23-2 2306. RECORDS 23-3 Figure 23-1 JOB HAZARD ANALYSIS WORKSHEET 23-4 CHAPTER 24 FIRE PREVENTION PROGRAM 2400. GENERAL 24-1 2401. GOALS AND OBJECTIVES 24-1 2402. SCOPE 24-1 2403. DEFINITIONS 24-1 2404. BASIC PROGRAM ELEMENTS 24-2 2405. FIRE PROTECTION EQUIPMENT 24-3 2406. FAA FACILITIES AND OPERATIONS 24-4 CHAPTER 25 FAA PERSONAL PROTECTIVE EQUIPMENT 2500. GENERAL 25-1 2501. GOALS AND OBJECTIVES 25-1 2502. SCOPE 25-1 2503. KEY PROGRA.M REQUIREMENTS 25-1 CHAPTER 26 RESERVED CHAPTER 27 RESERVED CHAPTER 28 RESERVED CHAPTER 29 RESERVED CHAPTER 30 RESERVED
Table of Contents
CHAPTER 31 OFFICE SAFETY 3100. GENERAL 31-1 3101. SCOPE 31-1 3102. STANDARDS 31-1 3103. KEY PROGRAM ELEMENTS 31-1 Figure 31-1 EXAMPLES OF OFFICE SAFETY TOPICS 31-3 CHAPTER 33 TOXIC AND HAZARDOUS SUBSTANCES CONTROL PROGRAM 3300. GENERAL 33-1 3301. GOALS AND OBJECTIVES 33-1 3302. SCOPE 33-1 3303. STANDARDS AND GUIDELINES 33-1 3304. PROGRAM REQUIREMENTS 33-1 CHAPTER 34 ELECTRICAL SAFETY 3400. GENERAL 34-1 3401. GOALS AND OBJECTIVES 34-1 3402. SCOPE 34-2 3403. KEY PROGRAM ELEMENTS 34-2 3404. USE OF EQUIPMENT 34-5 3405. SELECTION AND USE OF SAFETY RELATED WORK PRACTICES 34-5 3406. USE OF PERSONAL PROTECTIVE EQUIPMENT 34-6 3407. TRAINING 34-8 3408. DEFINITIONS 34-8
Chap 1 Page 1-1 Par 1
CHAPTER 1. GENERAL
CHAPTER 1. GENERAL
1. PURPOSE. This order establishes broad roles, responsibilities, and accountability for operating an Occupational Safety and Health (OSH) Program in the Federal Aviation Administration (FAA). This order assigns requirements of the Occupational Safety and Health Act, Public Law 91-596; Executive Order 12196, Occupational Safety and Health Programs for Federal Employees; and 29 Code of Federal Regulations Part 1960, Basic Program Elements for Federal Occupational Safety and Health Programs. This order implements DOT (Department of Transportation) 1000.17, Administrative Services Policy Functions.
2. DISTRIBUTION. This order is distributed to the director level in the Washington headquarters, regions, and centers; to the division level in the NAS Transition and Integration; to the division level in regional Air Traffic, Flight Standards, Human Resource Management, and Aviation Medical Divisions; to the branch level in the regional Airway Facilities Divisions; to the Environmental, Safety, and Emergency Management and Human Resource Management Divisions at the Aeronautical Center; and the Facilities Services and Engineering and Human Resource Management Divisions at the Technical Center; and a limited distribution to all field offices and facilities.
3. CANCELLATIONS.
a. Order 3900.6A, Occupational Safety Program for Airway Facilities Personnel, dated January 21, 1972.
b. Order 3900.14C, Safety Climbing Equipment at Existing NAS Facilities, dated February 23, 1972.
c. Order 3900.19A, Occupational Safety and Health, dated July 20, 1982.
d. Order 3900.23, Report of AF Occupational Safety Program, dated February 22, 1971.
e. Order 3900.24A, Accident and Fire Reporting, dated February 27, 1976.
f. Order 3900.49, Control of Hazardous Energy During Maintenance, Servicing, and Repair, dated July 17, 1992.
g. Order 3910.2A, Occupational Health Programs, dated January 5, 1973.
h. Order 3910.3A, Radiation Health Hazards and Protection, dated October 19, 1983.
i. Order 3910.5, Asbestos Control, dated February 19, 1986.
4. BACKGROUND. The occupational safety and health regulations of Federal, state, and local governments have become increasingly stringent over the past several years. Effective June 1993, the FAA Executive Board agreed to consolidate the occupational safety and health policy and implementation functions, with realignment of functions to the Office of Environment and Energy (AEE) and the NAS Transition and Integration (ANS).
Page 1-2 Chap 1 Par 5
5. EXPLANATION OF CHANGES. The order has been revised to include:
a. New roles and responsibilities to reflect the current FAA organizational structure and assignment of program responsibilities.
b. Updated chapters containing program elements necessary to the establishment and implementation of an agencywide occupational safety and health program in accordance with current standards and issuances of the Occupational Safety and Health Administration (OSHA). See paragraph 9, Standards.
c. Details on establishing and conducting an occupational safety and health committee have been removed and are now incorporated in a charter available through AEE. See paragraph 10a(2).
d. Authority for clearing changes or adding new chapters to this order. See paragraph 7.
e. Consolidation of previously separate occupational safety and health orders into this order. For example, FAA Order 3910.3A, Radiation Health Hazards and Protection, and FAA Order 3910.5, Asbestos Control, were canceled, the policies updated, and added to this order as chapters 14 and 15, respectively.
6. FORMS. FAA Form 3900-6, FAA Mishap Report, is included in Chapter 7, Accident Reporting and Investigation, as Figure 7-1.
7. AUTHORITY TO ISSUE CHANGES TO THIS ORDER. The Director of AEE has the authority to add new chapters or change existing chapters after appropriate coordination with stakeholder organizations. The Administrator reserves the authority to establish or change policy, delegate authority, or assign responsibility as necessary.
8. POLICY. This order sets the policy for the framework of the overall agency OSH program.
a. General. The FAA is committed to providing for the occupational safety and health of employees, preventing accidental loss of material resources, avoiding facility interruptions due to accident or fire, and enforcing a system of formal accountability. The FAA OSH program shall have top management commitment and support. The program shall integrate activities at all levels into FAA day-to-day operations.
b. Program Management. An OSH program must include, at a minimum, the following elements: program/project planning, forecasting requirements, budgeting, general and specific training, inspections and followup, including abatement, and developing evaluation standards to measure progress.
9. STANDARDS.
a. Occupational Safety and Health Standards. DOT and FAA have adopted the OSHA standards published in 29 CFR Part 1910, "Occupational Safety and Health Standards for General Industry," and 29 CFR Part 1926, "Safety and Health Regulations for Construction.” The standards apply to FAA workplaces. Variances from OSHA standards may be sought, as covered in Chapter 2, Workplace Inspections, Abatement Programs, and Variances.
b. Existing FAA OSH Orders. This FAA OSH program and related FAA orders shall be periodically reviewed for currency with OSHA standards and FAA organizational changes. The FAA OSH Program Manager for Policy (OSHPM/P), located in the Office of Environment and Energy (AEE), shall conduct the review. Orders not meeting OSHA standards shall be revised or revoked. For FAA orders found to be inconsistent due to changes in OSHA standards, the most current OSHA standard shall apply.
Chap 1 Page 1-3 Par 9
(1) The OSHPM/P shall attempt to resolve any conflicts with standards of another agency/jurisdiction involving FAA employee operations.
(2) The FAA OSHPM/P shall elevate unresolved conflicts to the FAA’s Designated Agency Safety and Health Official (DASHO), and finally to the appropriate DOT office for resolution.
c. Consensus Standards. FAA will apply OSHA standards and other non-FAA regulatory or current industry/consensus standards to equipment, operations, or workplaces. Non-FAA regulatory or consensus standards include, but are not limited to, those published by the American National Standards Institute (ANSI), American Society for Testing and Materials (ASTM), DOT, Environmental Protection Agency (EPA), and National Fire Protection Association (NFPA).
10. OCCUPATIONAL SAFETY AND HEALTH PROGRAM REQUIREMENTS. The FAA OSH Program shall include the following:
a. Program Elements. The elements of an occupational safety and health program include:
(1) A safety and health organization encompassing a comprehensive headquarters, regional, and center program, consistent with this order and with OSHA regulations. (Chapter 3, Safety and Health Organization)
(2) Safety and health committees at the national, regional, and field level. Occupational Safety, Health, and Environmental Compliance Committees (OSHECCOM) were established by charter on March 17, 1996. These committees advise and assist management in implementing and monitoring safety and health programs and provide a forum for information exchange.
(3) Qualified safety and health professionals with equipment, competence, and training available to recognize and evaluate workplace hazards and to suggest means to abate those hazards. (Chapter 4, Professional Qualifications and Training of OSH Staff)
(4) A safety awards program aimed at promoting positive employee response and personal accountability in safety and health activities.
(5) Written policies, programs, and procedures that provide appropriate direction, guidance, and program requirements.
(6) Budgets and plans at each operating level, ensuring appropriate financial and other resources are requested for OSH program implementation and administration.
(7) A safety and health management information system to record and track accidents, injuries, and illnesses. (Chapter 5, Safety and Health Management Information System)
(8) A program to transmit information on pending safety and health legislation or new regulations to appropriate staff; e.g., use of intranet homepages.
b. Training. A comprehensive occupational safety and health training program shall be established to incorporate general and job-specific training based on an individual’s duties and the workplace. (Chapter 6, Training and Awareness Programs)
Page 1-4 Chap 1 Par 10
c. Workplace inspection and abatement. Formal facility inspections and informal selfassessments will be conducted annually. Formal procedures for hazard abatement and accident investigations of injuries, incidents, and illnesses will be established. (Chapter 1, General; and Chapter 7, Accident Reporting and Investigation)
d. Measures of effectiveness. Measures to evaluate OSH program effectiveness will be established within the FAA. The OSH program will be audited and evaluated to track its success quantitatively and to identify areas requiring increased attention.
e. Dissemination of occupational safety and health program information. A copy of this order and related headquarters or region/center OSH orders and implementation guidelines shall be made available for inspection to each supervisor, OSHECCOM committee members, employee representatives, and employees. These shall also be made available to the Secretary of Labor or designee upon request.
11. DEFINITIONS.
a. Center refers to the Mike Monroney Aeronautical Center and the William J. Hughes Technical Center.
b. Designated Agency Safety and Health Official (DASHO) is the individual responsible for the management and administration of the safety and health program in the agency, as designated or appointed by the head of the agency. At the headquarters level, the DASHO is the Assistant Administrator for Policy, Planning, and International Aviation, API-1. In the regions and centers, the Regional Administrator or Center Director will appoint a Designated Region/Center Safety and Health Official (DR/CSHO) based on respective region/center needs and preferences.
c. Facility is a single physical location where agency business is conducted or where services or operations are performed. Where distinctly separate activities are performed at a single physical location, each activity shall be treated as a separate establishment. Typically, an “establishment” as used in this order refers to a field activity, regional office, center, installation, or site.
d. Management Representative is a supervisor or management official as defined in a labor management relations program.
e. Region/Center Occupational Safety and Health Manager (ROSHM/COSHM) is the technical person responsible for the employee safety and health program at the regional and center level. The ROSHM/COSHM serves as advisor to the RPMES and management on occupational safety and health issues and is a permanent voting member of the regional or center OSHECCOM.
f. Regional Program Manager for Environment and Safety (RPMES) serves as the regional and center associate program manager in performing the environmental compliance and occupational safety and health program implementation responsibilities and providing implementation guidance for compliance at regional division levels. The RPMES maintains copies of field OSHECCOM minutes and reports and is a permanent, voting member of the regional or center OSHECCOM.
g. Reprisal is any act of restraint, interference, coercion, or discrimination against an employee for exercising rights under E. O. 12196 and 29 CFR 1960 or for participating in the agency’s safety and health program.
Chap 1 Page 1-5 Par 11
h. Technically Qualified Safety Personnel:
(1) OSH Professionals: safety specialists, safety managers, safety engineers, or industrial hygienists; or equally qualified agency, military, or non-Government personnel who meet the basic qualifications of the above classifications as defined by AHR standards and recommended by the region/center occupational safety and health manager.
(2) Collateral Duty Safety and Health (CDSH) Personnel: personnel having sufficient OSH training and experience to perform general workplace safety inspections.
12. RESPONSIBILITIES OF HEADQUARTERS OFFICES.
a. The Operations Center (ADA-30) in the Office of the Deputy Administrator shall notify the OSHPM/P within 4 hours of all incidents covered by OSHA reporting requirements. These incidents include fatalities and/or when three or more employees are involved in an accident and hospitalized on an in-patient basis.
b. The Assistant Administrator for Policy, Planning, and International Aviation (API) shall:
(1) Serve as the DASHO to assist the Administrator in ensuring a comprehensive OSH program for FAA employees.
(2) Develop agency OSH policies, issue directives, and make recommendations.
(3) Initiate programs and actions to ensure compliance with applicable standards, policies, and requirements.
(4) Serve as a member of the FAA National OSHECCOM as defined in the OSHECCOM Charter. Also, act for the Administrator in interdepartmental safety and health matters.
c. The Office of Environment and Energy (AEE) within API shall:
(1) Establish OSH program policies consistent with OSH regulations and standards.
(2) Review guidelines and directives produced by other FAA organizations to implement OSH policies.
(3) Serve as FAA’s focal point for OSH policy issues for internal and external organizations, and provide OSH program liaison services for the FAA. Serve as the official point of contact for all OSH Freedom of Information Act (FOIA) inquiries. Provide these services for interactions with OSHA, National Institutes for Occupational Safety and Health (NIOSH), Environmental Protection Agency (EPA), the unions, and other regulatory or advisory agencies.
(4) Interpret OSHA regulations and industry/consensus standards.
(5) Conduct OSH program oversight assessments throughout the agency. (Chapter 8, Evaluation of the OSH Program.)
(6) Identify the training required to comply with all Federal Occupational Safety and Health and Environmental Compliance regulations, and provide a general definition of who should receive the training.
(7) Sponsor and oversee the FAA OSHECCOM as identified in the OSHECCOM Charter.
Page 1-6 Chap 1 Par 12
(8) Provide AEE budget needs to ANS and participate in budget discussions, as appropriate, to provide clarification of these needs for the national FAA Occupational Safety and Health Program.
(9) Develop and administer the FAA OSH Mishap Reporting and Safety Management Information System (SMIS), including trend analysis and data tracking.
(10)Track and initiate appropriate action for all employee allegations of discrimination, reprisal, or restraint as a result of his or her participation in the FAA Occupational Safety and Health Program.
d. The Office of the Chief Counsel (AGC) shall:
(1) Provide top management commitment and support of the OSH program per E.O. 12196.
(2) Determine the legal sufficiency of FAA occupational safety and health contracts, procedures, and correspondence.
(3) Provide legal advice and guidance on OSH implementation and compliance issues.
e. All Associate/Assistant Administrators shall:
(1) Provide top management commitment and support for the OSH program.
(2) Implement OSH policies within their respective organizations.
(3) Ensure that Washington headquarters and regional subordinate managers are aware of OSH requirements with which they must comply, and that they implement the agency OSH policies.
(4) Ensure adequate funds and resources are requested to comply with applicable OSH policies and regulations, such as training, travel, personal protective equipment (PPE), etc. These requests should be made according to the 2500 budget series orders.
(5) Ensure that their policies, procedures, and directives are updated as new occupational safety and health policies are issued.
(6) Designate an OSH person (as defined in paragraph 11h) for their respective line of business (LOB) who will serve as the point of contact to coordinate OSH issues with ANS and assist in the implementation of the agency OSH program.
(7) Ensure that OSH training needs are identified and addressed.
(8) Ensure that written procedures are in place to protect employees from discrimination, reprisal, or restraint as a result of their participation in the FAA Occupational Safety and Health Program.
f. The Assistant Administrator for Financial Services (ABA) shall ensure that the agency’s budget request includes adequate funding for OSH program needs.
g. The Assistant Administrator for Human Resource Management (AHR) shall:
(1) Serve as the agency’s focal point for the Office of Workers’ Compensation Program (OWCP), including claims processing, case management, and reassigning workers on light duty assignments.
(2) Ensure that all FAA OSH policies, training, and procedures are compatible with established labor and employee practices and meet regulatory requirements.
Chap 1 Page 1-7 Par 12
(3) Ensure that all FAA OSH program policies are consistent with affirmative action employment programs for minorities, physically challenged, veterans, and other special emphasis groups.
(4) Ensure that OWCP information is coordinated with OSH program managers and the Federal Air Surgeon for the purpose of measuring program effectiveness for setting program priorities.
(5) Ensure that position descriptions and employment standards accurately and specifically reflect the use of PPE, training requirements, participation in medical monitoring programs, and an ability to perform safely those duties that could affect the employee’s safety and health.
(6) Make hazardous duty pay and environmental differential pay determinations, in coordination with AEE, ANS, and AAM personnel, based on hazard assessment, AHR polices, OSHA standards, and OPM regulations (if applicable).
(7) Ensure that funds are requested to administer the Workers’ Compensation Program.
(8) Ensure that management and supervisory position descriptions reflect safety responsibilities and that performance reviews measure performance in meeting occupational safety and health requirements in accordance with OSHA standards.
h. The Associate Administrator for Research and Acquisitions (ARA) shall:
(1) Ensure compliance with all standards, as identified in paragraph 9, in the design and acquisition of emerging and deployed systems/equipment and real property management.
(2) Develop procedures to incorporate the most current version of the standards referenced in paragraph 9 into the requirements documents, requests for offer, FAA acquisition management system documents, contracts, designs, and acceptance testing protocols. Integrated product teams (IPT) and product teams (PT) shall include ANS as an extended team member in their program plans.
(3) Ensure designs apply human factors, practices, and principles and reflect concerns such as, but not limited to, minimizing employee exposures, hazardous component disposal, and safe operations and maintenance by using a life cycle and systems safety approach.
(4) Establish agencywide procedures to include compliance with all standards as identified in paragraph 9 of this order.
(5) Identify and ensure correction of OSH issues and concerns for FAA’s national headquarters [Federal Office Building (FOB 10A)] and coordinate with ANS as necessary.
(a) Appoint and train collateral duty safety personnel for FOB 10A to support the agency OSH program.
(b) Implement OSH policies within FOB 10A.
i. The Office of Aviation Medicine (AAM) shall:
(1) Provide medical evaluations, monitoring, and support as required by policy.
(2) Provide policy development technical support to the Office of Environment and Energy.
(3) Make recommendations on OWCP injury claims and light duty assignments.
Page 1- 8 Chap 1 Par 12
(4) Develop procedures to maintain occupational safety and health medical surveillance records in accordance with OSHA regulations and FAA policy.
(5) Ensure that adequate funds are requested to administer the medical surveillance programs that are required by OSHA.
(6) Ensure that appropriate medical surveillance information is coordinated with OSH program managers.
j. The NAS Transition and Integration Program (ANS) within the Airway Facilities Service (AAF) shall:
(1) Manage, coordinate, and direct the implementation of the FAA OSH program across lines of business/staff office boundaries.
(2) Request, allocate, and budget for all prioritized Facilities and Equipment (F&E) OSH requirements necessary for program implementation and management. Include all areas appropriate for F&E funding across lines of business and staff offices in accordance with the 2500 budget series orders.
(3) Develop guidance and planning documents to implement the FAA OSH program.
(4) Identify and prioritize requirements for all FAA OSH training. Assist the Resources Management Program (AFZ) in developing training.
(5) Provide technical support to ensure that OSH considerations are included in the life cycle management process.
(6) Provide technical assistance as appropriate to appropriate AF organizations to ensure that OSH guidance is included in AF technical and maintenance orders and related publications.
(7) Provide technical support in the development of Acquisition Management System (AMS) implementation procedures to incorporate all standards into requirements documents, contracts (including pre-contract awards), designs, and acceptance testing protocols.
(8) Provide technical support in the development of AMS requirements documents that reflect concerns such as, but not limited to, minimizing employee exposures, hazardous component disposal, safe operations/maintenance, system safety, and human factors.
(9) Provide technical assistance as needed to all national headquarters, regional, and center organizations on OSH implementation issues.
(10)Provide periodic updates to national headquarters management on OSH program progress, potential problems, and trends.
(11)Provide technical assistance as needed to headquarters building management on matters dealing with the safety and health of headquarters personnel.
(12)Provide technical or programmatic advice and/or assistance to ARA for OSH issues related to FOB 10A as necessary.
Chap 1 Page 1-9 Par 12
k. The Spectrum Policy and Management Program (ASR) within AAF shall:
(1) Serve as the agency focal point for information about ionizing and nonionizing radiation emission characteristics of all FAA-owned or -leased equipment.
(2) Coordinate with ANS in evaluating potential health hazards associated with employee exposure to radiation emissions from FAA-owned or -leased equipment.
(3) Assist AEE in developing and revising policy on employee exposure to radiation hazards related to FAA-owned or -leased equipment.
(4) Incorporate radiation safety into frequency spectrum engineering practices and when developing telecommunications and network planning.
(5) Ensure funds are requested to conduct surveys, training, and special studies.
(6) Ensure Frequency Management Officers schedule periodic radiation surveys and coordinate the scheduled and special request surveys with the RPMES’s and/or ROSHM’s/COSHM’s.
l. The Resources Management Program (AFZ) within AAF shall:
(1) Serve as the agency’s primary focal point for development, execution, and tracking of centralized OSH training across the lines of business in accordance with priorities set by ANS.
(2) Ensure funds are requested for OSH training requirements.
13. RESPONSIBILITIES OF THE REGIONS AND CENTERS.
a. Regional Administrators, AXX-1; Director, Mike Monroney Aeronautical Center (AMC-1), and Director, William J. Hughes Technical Center (ACT-1) shall:
(1) Provide top management commitment and support for the OSH program, to include the enforcement of safety regulations.
(2) Ensure that the Centers’ (AMC and ACT responsibility only) programs address OSH requirements in the planning, funding, and operation process.
(3) Incorporate applicable OSH requirements into specifications as well as contracts for inspection, construction, maintenance, and replacement of airway systems, facilities, and equipment; and acquisition of goods and services.
(4) Designate an executive level safety and health official as the DR/CSHO based on respective region/center needs and preferences.
(5) Ensure adequate funds and resources are requested to comply with applicable OSH policies and regulations like training, travel, and PPE. These requests should be made through the appropriate line of business and according to the 2500 budget series orders.
(6) Provide OWCP information to ROSHM’s/COSHM’s and regional flight surgeons for accident prevention purposes.
Page 1-10 Chap 1 Par 13
(7) Incorporate OSH requirements into existing and future technical training courses provided by the Aeronautical Center. (AMC responsibility only.)
b. Regional Airway Facilities Division Manager, AXX-400, Facility Management Program Director, AMP-1, and Facilities Services and Engineering Program Director, ACT-600 shall:
(1) Provide top management commitment and support for the OSH program.
(2) Manage and coordinate the implementation of the region/center OSH program across division/staff office boundaries to include planning and funding functions, as applicable.
(3) Assist division/staff offices in implementing the OSH program in their organizations.
(4) Ensure region/center resource requirements for OSH programs identified by all divisions are submitted to ANS.
(5) Provide an adequate number of technically qualified staff to support the region/center OSH program.
(6) Ensure procedures are in place to respond to employee reports of imminent danger or other immediate hazard concerns to protect employee safety. (Chapter 9, Reports by Employees on Hazardous Conditions)
(7) Ensure that written guidance and procedures are in place to expedite the notification of safety-related accidents, fatalities, and incidents to the emergency operations center or facility.
c. Regional Flight Surgeons (AXX-300) shall:
(1) Implement medical surveillance requirements in their region or center in accordance with this order and any written guidance provided by stakeholders; e.g., ANS.
(2) Ensure that funding for occupational medical services, including periodic medical monitoring, is addressed in the budgetary review process or elevated to the National Occupational Medicine Surveillance Program Oversight Team (NOMSPOT) in accordance with paragraph 1206.
(3) Ensure that occupational medical monitoring services are provided to all FAA employees who have been determined by AXX-400 as meeting regulatory requirements for inclusion in the region/center medical surveillance program. When there is a disagreement on the criteria or indications for examinations, the issue shall be resolved in accordance with the region/center OSH program and AAM guidance.
(4) Review available industrial hygiene exposure monitoring and/or related job hazard analyses prior to providing medical services.
(5) Coordinate changes to the region/center medical surveillance program with AAM and AXX-400.
(6) Provide AXX-400 with the results of employee medical monitoring for use in determining procedures to take to eliminate employee exposure to toxic and hazardous materials.
Chap 1 Page 1-11 Par 13
d. All Regional and Center Division Managers shall:
(1) Provide top management commitment and support for the agency OSH program.
(2) Implement OSH policies within their respective organization.
(3) Ensure that adequate funds and resources are requested in order to comply with applicable OSH policies and regulations like training, travel, and PPE. These requests should be made through the appropriate line of business and according to the 2500 budget series orders.
(4) Ensure all divisional programs and projects address current OSH requirements.
(5) Designate a representative as a contact point to work with the ROSHM/COSHM on OSH issues.
(6) Require supervisors to identify employee OSH training needs and provide input during the annual budget formulation.
(7) Provide appropriate representation and participation in the regional OSHECCOM.
(8) Appoint and train collateral duty safety personnel to assist in OSH program responsibilities.
14. RESPONSIBILITIES OF ALL FAA SUPERVISORS AND EMPLOYEES.
a. All Supervisors shall:
(1) Ensure that workplaces are inspected to identify and correct hazards and that completed job safety analyses (JSA) are available for appropriate work practices. Ensure that the results of the inspections and JSA’s are documented and maintained in accordance with OSHA standards.
(2) Ensure that all employees are trained in safety awareness and in safety precautions appropriate for their assigned tasks. Ensure the training records are documented and maintained in accordance with OSHA standards.
(3) Enforce safety rules and regulations and require the use of PPE when its use is dictated by job requirements.
(4) Ensure that accidents are investigated and that reports are completed to determine why they occurred. (Chapter 7, Accident Reporting and Investigation)
(5) Utilize the safety committee, collateral duty, and other occupational safety and health personnel as a source of advice and assistance.
(6) Ensure that all work-related injuries and illnesses are reported in accordance with prescribed procedures.
(7) Ensure annual inspections are conducted and documented.
(8) Provide commitment to the safety and health program.
Page 1-12 Chap 1
Par 14
b. All FAA Employees shall:
(1) Observe safe work practices, including the use of PPE, and comply with FAA and OSHA safety and health policies and standards.
(2) Promptly report unsafe and/or unhealthful working conditions, situations, work-related injuries, illnesses, and accidents to supervisors. (Chapter 9, Reports by Employees on Hazardous Conditions)
(3) Attend applicable OSH-related training sessions and committee meetings and comply with medical surveillance requirements.
(4) Provide commitment to the safety and health program.
Chap 2 Page 2-1 Par 200
CHAPTER 2. WORKPLACE INSPECTIONS, ABATEMENT PROGRAMS,
AND VARIANCES
AND VARIANCES
200. GENERAL.
a. Designated OSH personnel shall inspect all FAA workplaces at least annually to ensure safe and healthful working conditions. OSH workplace inspections shall occur at appropriate times and utilize methods that preclude or minimize disruption of the FAA’s mission and operations.
b. Designated OSH personnel are:
(1) OSH Professionals: safety specialists, safety managers, safety engineers, or industrial hygienists; or equally qualified agency, military, or non-Government personnel who meet the basic qualifications of the above classifications as defined by AHR standards and recommended by the region/center occupational safety and health manager.
(2) Collateral Duty Safety and Health (CDSH) Personnel: personnel having appropriate OSH training and experience to perform general workplace safety inspections.
201. INSPECTION OF WORKPLACES. Each FAA facility, including offices, shall be inspected by technically qualified safety personnel, who possess appropriate equipment to recognize unsafe and unhealthful working conditions in that workplace. For an OSHA inspection, a “facility” is a single physical location where business is conducted or where services or operations are performed. Facility managers are responsible for ensuring each facility is inspected. Inspections may occur concurrently with regularly scheduled maintenance. Inspection findings shall be documented.
a. Workplaces and agency facilities shall be categorized as a general workplace or increased risk workplace based upon an evaluation of the operations by OSH professionals. A list shall be maintained of increased risk workplaces. For each of the increased risk workplaces, a list of associated facilities shall be identified; e.g., facility (ARTCC), workplace (battery room), location or room number (basement). The list shall be updated at least annually with the revision date documented. However, workplaces shall be added to the increased risk list as soon as it is indicated that conditions change and the risk increased; i.e., accident reports, medical monitoring results, construction projects, etc.
b. Increased risk workplaces shall be inspected at least twice a year by an OSH professional. Regions/centers shall follow implementation guidelines established by FAA headquarters for classification of increased risk workplaces.
c. Non-FAA workplaces in which FAA personnel are present for short duration; e.g., air carrier establishments, do not require annual OSH inspections. However, provisions will be made to ensure the safety and health of FAA employees while in the contractor facility. Annual inspections are required for workplaces not owned by the FAA, in which FAA personnel are assigned on a full-time basis, e.g., ATCT. OSH personnel will ensure inspections are conducted. The responsibilities and conditions for the inspections will be delineated in real property agreements.
d. Additional inspections may be conducted beyond those required above, in order to ensure program viability and the elimination of hazards. These inspections may be announced or unannounced.
e. Inspections shall be conducted in accordance with 29 CFR 1960 and in a manner to preclude unreasonable disruption of the operations of the workplace and shall be consistent with the established and written region/center OSH program.
f. Documentation will be prepared by the inspector for each workplace inspection and made available upon request by region/center, headquarters, or authorized employee representatives.
Page 2-2 Chap 2 Par 201
g. Documentation shall contain, at a minimum, date of inspection, deficiencies, applicable regulatory references, abatement plans, name of inspector, and any other information as required by the region/center OSH program. Inspectors are encouraged to document proactive initiatives. Inspections uncovering no findings will be documented with date of inspection and name of inspector. Electronic systems may be used as documentation to facilitate the recording of the inspection. Documentation shall be maintained in accordance with 29 CFR 1960.
h. Notices of Unsafe or Unhealthful Working Conditions will be prepared, issued, and posted in accordance with 29 CFR 1960 and consistent with the established and written region/center OSH program.
202. ABATEMENT OF UNSAFE AND UNHEALTHFUL CONDITIONS AND PRACTICES.
a. An abatement plan is required for all unsafe and unhealthful conditions found during an inspection, reported by employees, or identified through other means; i.e., accidents, construction activities, system safety analysis, etc., which cannot be corrected within 30 calendar days. Responsibilities for the abatement plan will be established by the region/center OSH program.
b. The abatement plan will contain at the least the following standard data:
(1) Date of hazard.
(2) Location of hazard.
(3) Description of hazard.
(4) Estimated hazard severity and accident probability.
(5) Interim control measures.
(6) Description of the abatement action, including estimated cost and completion date.
(7) Closeout statement, indicating completed abatement action, actual cost, and date of completed action.
c. Abatement plans will be reviewed and followed up per 29 CFR 1960.30 by designated OSH personnel and kept in a central location as stated in the region/center OSH program.
203. VARIANCES. Variances from accepted OSHA standards may be requested in certain cases. Variances must clearly demonstrate an equivalent or greater level of employee protection.
a. Variance requests shall be reviewed in accordance with the established region/center OSH program and forwarded to ANS for initial processing. The written request will include:
(1) Description of the adverse condition.
(2) Identification of the applicable safety and health standard.
(3) Rationale for noncompliance.
(4) Description of the proposed alternative action.
Chap 2 Page 2-3 Par 203
(5) Explanation of how the alternative action will provide equivalent or greater protection.
(6) Description of interim protective measures until a decision is made by Washington headquarters and the Secretary of Labor.
b. ANS will review the variance request for adequacy and recommend whether or not it should be forwarded to the Secretary of Labor. ANS will forward the request to AEE for review and approval by the DASHO and official transmittal to the Secretary of Labor.
c. Requests not meeting equivalent protection criteria shall be returned by the office denying the request to the originator with an explanation for nonapproval.
Chap 3 Page 3-1 Par 300
CHAPTER 3. SAFETY AND HEALTH ORGANIZATION
300. GENERAL ORGANIZATION. An effective safety and health organization shall provide the roles, responsibilities, and authorities necessary to furnish each FAA worker with conditions of employment and a workplace free from recognized hazards. The organizational roles, responsibilities, and authorities shall be specified and implemented and periodically reviewed and revised as necessary.
CHAPTER 3. SAFETY AND HEALTH ORGANIZATION
a. Communications. Safety and health responsibilities must be defined in a formal statement and communicated so that managers, personnel, and safety and health staff understand their responsibilities.
b. Formal Organization Systems. Job descriptions of safety and health personnel shall clearly delineate responsibilities and reflect existing duties. Safety and health performance measures shall be job specific, and staff functional performance shall be evaluated during performance reviews.
c. Staffing. Full-time and collateral safety and health personnel shall be assigned to execute the safety and health program adequately. The operation unit’s total safety and health mission, goals, and objectives must be considered in determining the required number of personnel.
301. REGION/CENTER SAFETY AND HEALTH PROGRAM. Each region/center organization’s safety and health program will have standard safety and health program functions and tasks as part of the normal daily routine. The elements of a comprehensive safety and health program shall include:
a. Principal staff advisors, consultants, and coordinators for planning, organizing, directing, and evaluating region/center safety and health efforts.
b. Guidance for developing and implementing occupational safety and health plans and procedures according to OSHA regulations and FAA policy.
c. Policies and procedures to be used by regional and center managers and supervisors for unique activities.
d. Resources necessary to perform the OSH program.
e. Procedures to obtain professional assistance to eliminate unsafe or unhealthful conditions.
f. Procedures to assist supervisors in carrying out their safety and occupational health responsibilities.
g. Procedures for obtaining technical assistance in accident investigation and reporting according to FAA policy.
h. Accident data collection, analysis, and document preparation procedures.
i. A method to track completion of corrective measures or recommendations as appropriate to ensure a safe and healthful workplace.
j. Procedures to ensure safe practices and physical standards are incorporated into operating manuals, procedures, directives, and plans and that the documents are kept current.
k. Procedures for reviewing emergency plans.
l. Occupational safety and health training at all levels.
Page 3-2 Chap 3 Par 301
m. Close coordination with other FAA divisions and branches on safety-related issues.
n. Requirements for routine inspections and evaluations of safety programs and activities in accordance with chapter 1.
o. Procedures for performing planning and in-process engineering reviews for operations impacting worker OSH programs.
p. Liaison with counterparts in other Federal, state, or local agencies, ensuring cooperation on mutual interest issues.
q. Occupational safety and health reference material.
r. Requirements for membership on planning boards, ensuring existing and potential occupational safety and health issues are addressed.
302. POLICIES AND PROCEDURES.
a. The FAA employee safety and health program shall include clear written policies and procedures that provide appropriate direction and guidance. FAA policies and procedures shall be accessible to all personnel. Copies of safety and health standard operating procedures shall be available at each workplace, or, at a minimum, a central location, on the Internet, or on E-mail.
b. Routine procedural reviews shall be conducted as needed for changes in internal procedures or as a result of changes in safety and health regulations or FAA directives.
c. The FAA encourages the full support and participation of each employee in the Occupational Safety and Health Program. No employee shall be subject to discrimination, reprisal, or restraint as a result of his or her participation in the FAA Occupational Safety and Health Program.
303. PLANNING AND DECISIONMAKING PROCESS.
a. Each operating level shall systematically prepare budgets and financial plans to ensure appropriate financial and human resources are available to implement the OSH program.
b. Organizations shall conduct periodic safety and health reviews for all capital projects, research and development projects, and all major maintenance modifications.
CHAPTER 4. PROFESSIONAL QUALIFICATIONS AND TRAINING OF OSH STAFF
(Reserved)
CHAPTER 5. SAFETY AND HEALTH MANAGEMENT INFORMATION SYSTEM (Reserved)
CHAPTER 6. OCCUPATIONAL SAFETY AND HEALTH TRAINING AND AWARENESS
CHAPTER 6. OCCUPATIONAL SAFETY AND HEALTH TRAINING AND AWARENESS
PROGRAM (Reserved)
.
Chap 5 Page 5-1
CHAPTER 5. SAFETY AND HEALTH MANAGEMENT INFORMATION SYSTEM 500. GENERAL. The Safety Management Information System (SMIS) will be used to support FAA compliance with the reporting requirements set forth in 29 CFR 1960. It can also help management begin to use some of the best practices in mishap prevention. The FAA had a variety of independent mishap reporting schemes throughout the regions for years. The FAA has now deployed a system that brings all the FAA automation together and provides general safety information to employees and allows them to report workplace hazards. The system is located at http://smis.faa.gov and provides a tool through which supervisors are required to report mishaps. The system will allow Regional and Center Occupational Safety and Health Managers (ROSHM/COSHM) to use the data to track hazard abatement and mishap trends, which they send to affected managers. Supervisors and managers are then required to plan and budget for the abatement in accordance with 29 CFR 1960.7 and in Chapter 1, paragraphs 10(a)(6), 12(e)(4), 13(a)(5), and 13(d)(3) of this order.
Supervisors have been assigned user IDs and passwords and can call AMI-200 if they experience difficulty accessing the website. AEE-200 is the System Administrator. 501. MISHAP REPORTING. Chapter 7, Mishap Reporting and Investigation, requires employees to report all work-related injuries, illnesses, motor vehicle accidents, and property damage to supervisors. Supervisors and managers are required to investigate mishaps and report them using the website. If access to the website is not available, supervisors will complete the paper version of FAA Form 3900-6 and submit to the ROSHM/COSHM in accordance with procedures established by the lines of business (LOB), Region or Center.
a. The initial notification shall be provided to the immediate supervisor by the affected employee.
b. The immediate supervisor or manager will enter mishap information into the SMIS website. 502. HAZARD REPORTING. Procedures in Chapter 9, Reports by Employees on Hazardous Conditions, require employees to report orally or in writing to supervisors, any unsafe, unhealthful, or unsatisfactory work condition that may result in injury, illness, or property loss. The employee may use FAA Form 1800-1, Unsatisfactory Condition Report, and submit it in accordance with established procedures in FAA Order 1800.6. The supervisor will use SMIS to report OSH hazards electronically, but if access to the website is not available, then Form 1800-1 may be used.
a. The employee shall provide the initial verbal or written notification of an unsafe, unhealthful, or unsatisfactory condition to the immediate supervisor.
b. If the written notification is a UCR, the supervisor does not need to enter the hazard into SMIS, since the UCR will eventually be input electronically into SMIS.
c. If the notification was provided orally or in writing in accordance with Chapter 9 of this Order, then the immediate supervisor will enter the hazard information into SMIS.
d. SMIS is designed to notify the ROSHM via electronic mail. 503. SAFETY INFORMATION (OPTIONAL). 29 CFR 1960.12 (c) requires the dissemination of occupational safety and health program information. Supervisors may use safety information on the website for safety briefings to promote general safety awareness.
a. Safety Campaigns. Supervisors can download seasonal safety newsletter information and incentive program material for dissemination among the immediate workforce.
b. Success Stories. Any FAA employee can submit a Seatbelt Survivor story, Safety Success story or other Lesson Learned by submitting the story to on cc:Mail to [email protected].
Page 5-2 Chap 5
c. Optional Safety Training Information. Lines of Business (LOB) are responsible for identifying, developing, and providing OSH training for their employees. Generic, sample training programs are provided on this website and may be used by LOBs in establishing training requirements. The courses are also available in video, or CD format from AFZ-100. Supervisors shall consult with their LOB OSH point of contact to determine what OSH training is required.
d. Optional Safety Program Evaluation Criteria. AEE is developing specific Program Evaluation criteria for their use in National LOB Program Evaluations. These criteria will be available for each LOB to use to self assess their OSH Program and for supervisors to better understand how their safety performance contributes to LOB OSH success.
e. Optional Facility Safety Inspection. Annual workplace inspections are required by paragraph 201 of Chapter 2 of Order 3900.19B, Workplace Inspections, Abatement Programs, and Variances. Lines of business shall develop procedures to ensure these inspections are conducted. A generic OSH facility inspection aid is included in the SMIS for LOBs information and use as appropriate
Chapter 6 Page 6-1 1
Chapter 6 Page 6-1 1
CHAPTER 6. OCCUPATIONAL SAFETY AND HEALTH TRAINING AND
AWARENESS PROGRAM 600. GENERAL. This chapter delineates standards and program elements for the FAA Occupational Safety and Health (OSH) Training and Awareness Program. Regulatory training requirements are contained in 29 CFR 1910, “Occupational Safety and Health Standards for General Industry," 29 CFR 1926, “Safety and Health Regulations for Construction,” and 29 CFR 1960, “Basic Program Elements for Federal Employee Occupational Safety and Health Programs and Related Matters. In addition, recognized national consensus standards are published by organizations such as the American National Standards Institute (ANSI), and the National Fire Protection Association (NFPA) and other related standards setting organizations. 601. BACKGROUND. a. The FAA is committed to developing and maintaining well-trained, qualified, and competent personnel to operate and maintain FAA facilities and perform work tasks in a safe and reliable manner. This training chapter is a catalyst for managers to use to meet these expectations.
CHAPTER 6. OCCUPATIONAL SAFETY AND HEALTH TRAINING AND
It is important for FAA managers to be actively involved in the development and implementation of their facility's initial and continuing training programs, the identification of training needs, and the review and approval of training materials. b. Training programs shall provide the basic OSH knowledge and skills to perform intended job functions. Training may include a combination of classroom, computer-based instruction, self-study, and on-the-job instruction. 602. SCOPE. This chapter describes the elements of an OSH training program for FAA personnel, not including occupational safety and health professionals, as described in 29 CFR 1960.2(s). 603. PROGRAM ELEMENTS. a. Training of Top Management Officials. The FAA shall provide top management officials with orientation and recurrent learning experiences, which will enable them to manage their occupational safety and health program in accordance with 29 CFR 1960.57. Such orientation should include coverage of section 19 of the OSH Act, Executive Order 12196 and the FAA agency safety and health program.
Assistant Administrators, Associate Administrators, Service Directors, Office Directors, Regional Administrators, and Regional Division Managers are top managers. The content of this training will provide top managers with current knowledge needed to be able to:
(1) Communicate the FAA’s OSH goals and objectives to all employees.
(2) Assign safety and health roles and responsibilities.
(3) Recognize training resources necessary to carry out assigned tasks.
(4) Ensure managerial and supervisory accountability for OSH performance.
(5) Support the OSH program.
(6) Ensure that OSH policies, goals, and objectives are evaluated.
(7) Ensure accident reporting and investigation procedures are followed.
(8) Support facility inspection standards.
Page 6-2 Chapter 6
(9) Incorporate OSH program elements into the planning and budget process.
(10) Ensure hazards are identified and abated. b. Training of Supervisors. The FAA shall provide initial and recurrent occupational safety and health training for supervisory employees that includes: Supervisory responsibilities for providing and maintaining safe and healthful working conditions for employees, the agency occupational safety and health program, section 19 of the Act, Executive Order 12196, occupational safety and health standards applicable to the assigned workplaces, agency procedures for reporting hazards, agency procedures for reporting and investigating allegations of reprisal, and agency procedures for abatement of hazards. The supervisory training should include the introductory and specialized courses and materials that will enable supervisors to recognize and eliminate, or reduce, occupational safety and health hazards in their working units.
Such training shall also include the development of requisite skills in managing the FAA’s safety and health program within the work unit, including the training and motivation of their employees toward assuring safe and healthful work practices. c. Training for OSHECCOM Committee Members. OSHECCOM committee members shall be trained in accordance with 29 CFR 1960.58 and as outlined in the OSHECCOM Charter. d. Contractor Requirements. Contract statements of work shall require contractors to comply with all applicable federal, state and local OSH training regulations and to conduct their own OSH compliance training for their employees. The FAA shall provide site-specific information and/or training to protect contract employees from recognized workplace hazards on FAA premises. e. Training for Employees and Employee Representatives. All FAA employees shall receive initial and recurrent safety and health training, including specialized job safety training appropriate to the work performed. The FAA shall adhere to 29 CFR 1960.59(a) and (b).
Employee OSH training must occur when: an employee is hired or reassigned, new equipment or processes are introduced, procedures are revised or updated, or when employee performance indicates a need for additional training. At a minimum, the content of this training shall provide employees with the awareness needed to be able to:
(1) Recognize safety risks in the workplace.
(2) Become aware of employee OSH rights and responsibilities.
(3) Use personal protective equipment properly.
(4) Report all mishaps and hazards to supervisors and managers.
(5) Follow mishap prevention and hazard abatement programs.
(6) Achieve certification or qualification, if required by the job. f. Training Records. All safety training shall be documented in accordance with OSHA regulations and applicable FAA orders. Documentation shall be readily available for OSH program audits.
Page 119 Chap 7
CHAPTER 7. MISHAP REPORTING AND INVESTIGATION
CHAPTER 7. MISHAP REPORTING AND INVESTIGATION
700. GENERAL. This chapter outlines FAA requirements based on OSHA regulation 29 CFR 1904. Region or Center Occupational Safety and Health (OSH) program offices must provide all reports referenced in this chapter to AHR, AFZ and AEE on request. The Safety Management Information System (SMIS) at http://smis.faa.gov/ shall be used for reporting mishaps. 701. MISHAP INVESTIGATION.
a. A mishap includes an OSHA recordable occupational injury or illness (see paragraph 702, Reporting of Occupational Injuries or Illnesses) as well as an incident that results in no injury and is limited to property damage.
b. The immediate supervisor must consult with the Regional Occupational Safety and Health Manager (ROSHM) to ensure that an investigation is conducted for Class A, B and C mishaps. The immediate supervisor should also conduct mishap investigations for Class D motor vehicle accidents, fires, equipment and property damage. (See Figure 7-2, Line 17 of this chapter for Mishap Classes).
c. The purpose of mishap investigation is to reduce the potential for recurrence. All causal factors must be identified and fully explored. The extent of mishap investigation should reflect on the seriousness of the mishap. In any event, all OSHA recordable injuries and illnesses must be investigated according to OSHA regulations and FAA policy.
d. The immediate supervisor, or designee must investigate and provide a written report of the results using Figure 7-1, FAA Form 3900-6, FAA Mishap Report or its successor. The SMIS website at http://smis.faa.gov/ must be used for mishap investigation by all supervisors who have web access. The SMIS will E-Mail the ROSHM in the location where the mishap occurs, and the ROSHM in the region where the person is assigned to aid in completing a thorough investigation. The ROSHM and line of business OSH point of contact will provide technical guidance in mishap reporting and investigation.
e. Form 3900-6 (or succeeding form) must be forwarded to the ROSHM or line of business OSH points of contact within seven working days. Electronic submission using http://smis.faa.gov/ is highly preferred. Investigations of deaths must begin within 24 hours. Reports identifying potentially serious conditions should be investigated within 3 working days and within 7 working days for other than serious conditions.
702. REPORTING OF MISHAPS.
a. Process.
(1) Employees must promptly report mishap to immediate supervisor. (2) Supervisors must complete reports as pointed out in paragraph 702b. (3) Supervisors must determine the “mishap class” for example, A, B, C, D, N, and “incident type”; for example, injury, illness, property damage, motor vehicle damage, first aid, near miss. See Figure 2 FAA Mishap Form 3900-6 Definitions.
(4) SMIS enables the supervisor to use the secure FAA intranet to automatically maintain the OSHA Log 300 Log and OSHA 300A summary, and print it out as needed. The supervisor shall report injuries and illnesses when the mishap involves any of the following:
(a) Death occurred in the performance of duty (b) An injury resulting in 1 or more days of lost time (c) Loss of consciousness (d) Restricted work activity (e) Transfer to another job or light duty
Par 700
Page 120 Chap 7
(f) Medical treatment beyond first aid, or (g) An occupational illness
(5) OSH professionals and Office of Workers’ Compensation Program (OWCP) Specialists shall insure that FAA form 3900-6 and /or CA-1 or CA-2 reports respectively are sufficiently complete to simplify hazard identification and trend analysis. SMIS provides automatic notification to OSH personnel when mishaps have been entered.
b. Injury & Illness Reports.
(1) After an employee notification of injury or illness supervisors will continue to follow OWCP procedures in 20 CFR 10.100 and complete the supervisory portion of either the CA-1 (for injuries) or CA-2 (for illnesses). The employee must give the completed form to the Regional/Center OWCP Specialist. Management is responsible for completing FAA Form 3900-6 on the web at: http://smis.faa.gov for all property damage, fires and motor vehicle mishaps and injury/illness mishaps. Supervisors who do not have access to the web may give a paper version of FAA Form 3900-6 (copied from this chapter) to the Regional or LOB OSH Professional, who will enter the data.
(2) If the employee wants to file Form CA-1 or CA-2, he/she must initiate it promptly and forward it to the supervisor for completion of the supervisory section and signature. Printable copies of the blank CA-1, CA-2, and CA-6 forms are available under the “Forms” tab in SMIS. The employee must give the completed form to the FAA Workers’ Compensation Specialist. The form may be completed for all work-related injuries or illnesses regardless of whether the injury or illness results in actual or expected lost time, or medical expense. A copy should be given to the Regional or LOB OSH Professional.
(3) The investigation report should include details from local police, fire, and autopsy reports.
c. Timelines.
(1) Supervisors must ensure the Establishment/Facility Manager has the information necessary to complete the Log of Occupational Injuries and Illnesses within 6 days of receipt. This requirement is met automatically by completing Form 3900-6 in SMIS. If the employee wants to file form CA-1 or CA-2, he/she must forward it to the Regional OWCP Specialist who will then forward the forms to the Department of Labor within 10 working days of the supervisor’s receipt of the form.
(2) Management is responsible for providing first notice to the OSHA area office of any death or the in-patient hospitalization of three or more employees involved in one incident within 8 hours after the incident. When a work place incident occurs during OSHA’s off hours, the SSC or facility manager will contact OSHA’s recording service at 1-800-321-OSHA. In addition, management must notify the ROSHM and Line of Business OSH professional as soon as possible. The ROSHM and OSH professional shall report the incident to AEE-200 and AFZ-800 within 24 hours. AEE is the liaison to OSHA and will formally report mishaps to OSHA. The report must relate the circumstances of the mishap, names of the individuals involved, any actions taken by the FAA, the number of deaths, or injuries and illnesses, and the extent of injury. AEE will provide the Office of Federal Agency Programs a summary report, as 29 CFR.1904 requires.
(3) DOT Order 3910.1C requires drug or alcohol testing immediately after the mishap occurs, if management suspects drug or alcohol use, especially in the case of motor vehicle accidents. The Internal Substance Abuse Program’s “Site Coordinators Handbook” is available on the web at: http://www.faa.gov/avr/aam/isap/.
(4) Supervisors shall forward a copy of the lost time report to the OWCP regional coordinator for verification at the end of each calendar year. 703. RECORDKEEPING. Supervisors must enter injury/illness data on the OSHA 300 log within 6 days of the incident. The OSHA 300 Log must contain injury/illness data from the previous calendar year and be posted from February 1st through April 30th in a prominent place in the Establishment. SMIS is
Par 702
Page 121 Chap 7
designed to allow management to automatically update and maintain OSHA 300 Logs for their Establishments. The “Establishment” is determined by selecting the Location ID and Facility type within SMIS. These records must be maintained for a period of 5 years. SMIS also contains CA-1, CA-2 and CA- 6 data from the WCIS database and makes it available to ROSHMS and designated LOB contacts to use in performance of their duties. 704. FATAL AND CATASTROPHIC MISHAPS.
a. Supervisors will report all deaths that occurred while an employee was performing work duties. The 3900-6 will be submitted in SMIS.
b. The supervisor sends the CA-6 form to the appropriate AHR office for processing by OWCP. c. The AXX-400, AMP-1, or ACT-1 will appoint an investigation team for an on-duty death or for the hospitalization of three or more employees that occurs because a single mishap.
(1) The team will prepare a written report and forward it through the designated region or center LOB contact to AFZ-800 and AEE-200 within 15 days after completing the investigation.
(2) OSHA regulation 29 CFR 1960.70b and 29 CFR 1960.70c and paragraph 704c below describe the minimum procedures for the investigation team.
d. Investigation reports should include proper documentation, photographs, employee interviews, witness reports, measurements, and other relevant information. A checklist of items to be covered in the narrative report is shown as Figure 7-2, Checklist of Information to be Included in the Mishap Investigation Report.
e. Report copies will be provided to the Establishment (facility) Manager, the appropriate OSH committee, AXX-400, regional administrator, center director, and national headquarters. Distribution will be made in accordance with the region or center OSH program. If requested, the report must be available to the Secretary of Labor or a representative. 705. MOTOR VEHICLE MISHAPS. A motor vehicle accident is an occurrence involving a Federal Government-owned, leased, or rented vehicle, or privately owned vehicle while operated on official Federal Government business. This kind of mishap may result in death, injury or property damage of two thousand dollars ($2000) or more. A vehicle operator or their supervisor must complete the following forms;
a. SF-91, Accident Investigation Data, b. SF-94, Statement of Witness, c. CA-6 form for all deaths (and forward through the appropriate AHR office to OWCP). 706. OTHER MISHAPS. The contracting officer’s technical representative (COTR) must assure contractors give a written report for all incidents involving property damage or OSHA recordable employee injuries to the Establishment or System Maintenance Office Manager, Office of Procurement and Property Management. The COTR shall provide a copy of the report to the ROSHM within 48 hours of the mishap. When visitor mishaps occur, the Establishment Manager and the Security Official will complete a report and forward it to the Program Services Section, AXX-400, within 2 working days of the incident. The ROSHM must have authority to conduct full and independent investigations of visitor mishaps. 706-799. RESERVED.
Par 703
Page 122 Chap 7
Figure 7-1. FAA Form 3900-6, FAA Mishap Report
Fig 7-1
Page 123 Chap 7
Figure 7-1. FAA Form 3900-6, FAA Mishap Report, contd.
FAA Form 3900-6 (October 2003)
Fig 7-1
Page 124 Chap 7
Figure 7-2. FAA FORM 3900-6 DEFINITIONS TABLE
Block Heading Definitions 1 Injury Injuries result from mishaps that produce a wound or other adverse condition of the body caused by external force, including physical stress or strain. The damage to a person’s body can result from exposure to a single hazardous event or incident, or series of events or incidents within a single day or work shift. An injury is OSHA-recordable if certain criteria are met. See definition in Block 7. 1 Illness Illnesses result from: mishaps that cause physiological harm or loss of capacity produced by a systemic infection; OR exposure to toxins, poisons, fumes, etc.; OR a continued or repeated physical stress or strain; OR other continued and repeated exposures to conditions of the work environment, typically over a long period of time. Examples include: Musculoskeletal disorders (such as carpal tunnel syndrome), sensitivity to chemicals, and back strain if attributable to long term lifting. An illness is OSHA-recordable if certain criteria are met. See definition in Block 7. 1 Property Damage
A property damage incident is one where one or more FAA-owned/leased, or GSA-controlled, facilities, systems, equipment, or other personal or real property has been damaged. Property damage is classified in Block 17 as Mishap Classes A, B, C, D, and N and may require that an investigation be performed. See the definitions for Blocks 17 and 58. If this block is checked, provide the requested information in Section III. 1 Motor Vehicle A motor vehicle incident where damage occurs to an FAA-owned/leased, or GSA-controlled, government motor vehicle, or to a privately owned vehicle (POV) used on official FAA business. Vehicles driven by FAA personnel under temporary duty (TDY) conditions are considered on-duty. For the purpose of mishap prevention, all FAA motor vehicle mishaps and near misses must be recorded on this form, regardless of damage dollar value. 1 First Aid A first aid incident means any one-time treatment and subsequent observation of minor scratches, cuts, burns, splinters, insect bites, and so forth, which do not ordinarily require medical care. Such treatment and observation are considered first aid even though provided by a physician or registered professional personnel. 29 CFR 1904.7(b)(5)(ii) provides the following list of all treatments considered first aid for recordkeeping purposes:
• Using a non-prescription medication at non-prescription strength • Administering tetanus immunizations (but other immunizations such as Hepatitis B or rabies are considered medical treatment) • Cleaning, flushing, or soaking wounds on the surface of the skin • Using wound coverings such as bandages, gauze pads, butterfly bandages, steri-strips (but other wound closing devices such as sutures, staples, etc. are considered medical treatment) • Using hot or cold therapy • Using any non-rigid means of support, such as elastic bandages, wraps, non-rigid back belts (but devices with rigid stays or other systems designed to immobilize parts of the body are considered medical treatment) • Using temporary immobilization devices while transporting an accident victim (e.g., splints, slings, neck collars, back boards) • Drilling of a fingernail or toenail to relieve pressure or draining fluid from a blister • Using eye patches • Removing foreign bodies from the eye using only irrigation or a cotton swab
Fig 7-2
Page 125 Chap 7
Block Heading Definitions • Removing splinters or foreign material from areas other than the eye by irrigation, tweezers, cotton swabs, or other simple means • Using finger guards • Using massages (but physical therapy or chiropractic treatment are considered medical treatment), or • Drinking fluids for relief of heat stress 1 Near Miss A near miss incident occurs when a person was able to avoid injury and/or illness, and when no property damage occurs. A near miss is not OSHArecordable, but documentation of near misses is important for developing mishap prevention strategies. 1 Other Other incidents include: chemical spills, fires, violent acts, damage due to acts of nature, etc. 2 Incident Description
Thoroughly describe the incident answering the basic questions of who did what, when, where, how, and why. 7 OSHA Recordable
Mishaps are OSHA-recordable if they involve any of the following and are work-related:
• Death • Days away from work • Restricted work or transfer to another job • Medical treatment beyond first aid • Loss of consciousness • A significant injury or illness diagnosed by a physician or other licensed health care professional Ref: 29 CFR 1904 Subpart C – Recordkeeping Forms and Recording Criteria. 11 WCIS Case Number
A Workers’ Compensation Information System (WCIS) case number is assigned by the workers’ compensation system when a CA-1, CA-2, or CA-6 is filed. The workers’ compensation specialists in the regional Human Resource Management Divisions use WCIS for processing and tracking purposes. The number can be obtained from Human Resources, or through a search of the WCIS data feed in SMIS. 13 Location ID A Location Identifier stands for the name and the location of an airport, navigation aid, weather station, and manned air traffic control facility in air traffic control, telecommunications, computer programming, weather reports, and related services (FAA Order 7350.7G, Location Identifiers). This form will use the 3-letter Location Identifiers listed in Section 6, Assignments Listing. For example, ZAN is listed as the 3-code identifier for the Anchorage, AK ARTCC. The identifiers can be viewed by clicking “Location ID Table” in the Support link near the top right side of each SMIS page. 14 General Location of Incident
A General Location is a broad description of where the incident occurred. For example, 53325 Airport Road, El Segundo, California. 15 Specific Location of Incident
A Specific Location is a detailed description of where the incident occurred. For example, Room 223 on the second floor, near the auxiliary backup generator. 16 On Premises Refers to mishaps that occur at FAA-owned or leased property, or GSAcontrolled property, and includes the primary work facility and other areas, such as storage facilities, cafeterias, and restrooms. 17 Mishap Category Mishaps shall be categorized for purposes of trend analysis into one of the following classes, based on degree of severity (Category A is most severe). Select only one category. If more than one category applies, then select the
category with greater severity. A mishap categorized as any of Class A through D must be investigated (Section V – see definition for Block 58).
• Class A Mishap
o Recordable damage of $1M or more
Fig 7-2
Page 126 Chap 7
Block Heading Definitions o A fatality or permanent total disability • Class B Mishap
o Recordable damage of $200K or more but less than $1M o A permanent partial disability o Inpatient hospitalization of 3 or more personnel • Class C Mishap
o Recordable damage between $10K and $200K o An injury resulting in a lost workday case involving 8 hours
or more away from work beyond the day or shift on which it occurred; or occupational illness that causes loss of time from work at any time. • Class D Mishap
o Total cost of $2K or more for property damage but less than
$10K. Property damage includes all government equipment and vehicles. o A nonfatal injury that does not meet the definition of a
Class C Mishap, and results in less than 8 hours of lost time. These include: loss of consciousness, permanent change of job due to injury/illness, or medical treatment beyond first aid. Examples: Individual loses consciousness from heat stress while working in high temperature environment; or individual is injured, goes to personal physician on same day of injury and returns to duty the next day. • Class N Mishap
o Total cost of $1 or more for property damage but less than
$2K. o Any other injury that does not meet the above class criteria.
These should be reported for trend analysis. Example: First Aid treatments; near misses. 19 Description of Injury/ Illness
Describe the injury or illness, describing clearly and concisely the nature and cause of injury that might not be captured fully by the codes in blocks 19-22. Please include contributing factors that led to the injury or illness, such as fatigue, insufficient training, lack of personal protective equipment, faulty equipment, prescription drugs, etc. This information will be helpful if an investigation is performed (Section V). 20 Nature of injury/Illness Codes
Nature of injury or illness names the principal physical characteristic of a disabling condition, such as sprain/strain, cut/laceration, or carpal tunnel syndrome. Useful resources for information on the listed conditions include the Bureau of Labor Statistics’ (BLS) Occupational Injury and Illness Classification Manual at http://www.bls.gov/iif/oshwc/oiicm1.pdf, and BLS’ new Injuries, Illnesses, and Fatalities (IIF) program at http://www.bls.gov/iif/. 21 Part of Body Affected
Also known as “Part of Body Affected,” this is directly linked to the nature of injury or illness cited, for example, back sprain, finger cut, or wrist and carpal tunnel syndrome. 22 23 Type of Injury/Illness Codes
Both Type and Source Codes are used to describe what caused the injury or illness. The Type Code stands for an action and the Source Code stands for an object or substance. If there are two different sources, please use the code for the initiating source of the incident. For example, if an employee tripped on the carpet and struck his head on a desk, use Type: 210 (Fell on same level) and Source: 0110 (walking/working surface). This example would not be coded Type: 120 (struck against) and Source: 0140 (furniture). If in doubt about the codes to use, please contact your Regional Safety and Health Manager or organizational OSH point of contact. If you do not find a suitable
Fig 7-2
Page 127 Chap 7
Block Heading Definitions code, select “Other – Specify” at the bottom of the list. You must then fill in the adjacent box before you can move forward through the form.
Adapted from: Recordkeeping and Reporting Guidelines for Federal Agencies (OSHA 2014 – 1986)
24 Total Days Lost Enter the calendar dates for the estimated/verified days lost or the estimated/verified total number of days lost. Do not include date of the mishap. (Alternatively, you can enter the total number of days in the totals box.) To enter the dates, begin with the first full day lost subsequent to the date of the mishap. The ending date should be the first full day the employee returns to work. This will provide an accurate automated calculation of the total days lost. For example, an employee was injured at noon on 1/2/03 and went home for the remainder of the day, returning to work on 1/15/03. You would select 1/3/03 as the first lost work day and 1/15/03 as the first day back at work. SMIS will correctly calculate 12 as the total days lost, including the weekends, in accordance with OSHA Part 1904, Recordkeeping. Please select whether the days provided are “estimated” or “verified.” Then select the person providing the data. This would be the regional occupational safety and health manager (ROSHM), the safety and environmental compliance manager (SECM), or the supervisor. This information can be updated through the Modify Mishap feature. 25 Total Restricted/ Job Transfer Days
Enter the calendar dates for the estimated/verified period that an employee will perform or has performed restricted work; or will be transferred or was transferred temporarily to another job. (Alternatively, you can enter the total number of days in the totals box.) To enter the dates, begin with the first full day of restricted or transferred activity. The ending date should be the first full day the employee returns to work. This will provide an accurate automated calculation of the total days lost. For example, an employee was injured at noon on 1/2/03 and went home for the remainder of the day, returning to work on 1/15/03. Restricted activity began on 1/15/03 and you estimate the employee will return to regular duty on 1/23/03. You would select 1/15/03 as the first full day of restricted activity and 1/23/03 as the first day back on regular duty. SMIS will correctly calculate 7 as the total restricted days, including the weekend, in accordance with OSHA Part 1904, Recordkeeping. Please select whether the days provided are “estimated” or “verified.” Then select the person providing the data. This would be the regional occupational safety and health manager (ROSHM), the safety and environmental compliance manager (SECM), or the supervisor. This information can be updated through the Modify Mishap feature. 26 Medical Treatment by Licensed Health Care Professional
This block should be checked “yes” if treatment of the injury or illness was administered by a licensed health care professional, such as a physician, Registered Nurse (RN), or a Physician’s Assistant (PA). OSHA’s Part 1904 states that medical treatment does not include:
• Visits to a physician or other licensed health care professional solely for observation or counseling; • The conduct of diagnostic procedures, such as x-rays and blood tests, including the administration of prescription medications used solely for diagnostic purposes (e.g., eye drops to dilate pupils); • or First Aid, even if provided by a licensed health care provider. (See the definition for First Aid in block 1). 27 Fatality The fatality box should be checked “yes” if the incident is work-related and:
• a legal death certificate has been issued by a licensed and authorized medical authority who has determined that the employee is deceased, or
Fig 7-2
Page 128 Chap 7
Block Heading Definitions • a CA-6 has been submitted 32 Description of Damage
Describe the damage, describing clearly and concisely contributing factors that led to the damage, such as fatigue, insufficient training, faulty equipment, etc. Where possible, include in the narrative descriptors for when, what, why, how, and who. This information will be helpful if an investigation is performed (Section V). 33 Types of Damage Codes
Select the best code that describes the major source/cause of the damage. For example, an auto accident using a government vehicle in icy conditions may be best classified as "Environmental Conditions". The selection should not identify what was damaged, but what caused the damage. 49 Cost Center Enter the employee’s cost center code. Cost center codes are used in all financial, personnel, payroll, and other management data systems for the purpose of identification of organizations. FAA Order 1375.7G is the source of these codes. The codes may be viewed by clicking “Cost Center Table” in the Support link on the right side of the SMIS Information page. 56 Location Identifier for OSHA 300
A Location Identifier stands for the name and the location of an airport, navigation aid, weather station, and manned air traffic control facility in air traffic control, telecommunications, computer programming, weather reports, and related services (FAA Order 7350.7G, Location Identifiers). This form will use the 3-letter Location Identifiers listed in Section 6, Assignments Listing. For example, ZAN is listed as the 3-code identifier for the Anchorage, AK ARTCC. See #13 above. 57 General Job Task The general job task is a broad description of what the individual has been
assigned to do, such as radar system calibration. 58 Specific Job Task
The specific job task is a narrow description of what the individual was doing at the time of the mishap, such as discharging a capacitor on a circuit board. 64 Investigation Performed
Completion of an investigation by technically qualified safety personnel (TQSP) is required for the mishaps categorized in Block 17 as Class A or Class B. A supervisor may initiate an investigation for Classes C, D, and N. Depending on the severity, additional investigation will be performed by the TQSP, such as a Regional Occupational Safety and Health Manager or his/her qualified designee, and/or the LOB OSH POC (if qualified), in accordance with Chapter 7 of Order 3900.19B. An investigation will provide valuable information that will help to identify future mishap prevention strategies. Further information about the investigation process is in Chapter 7 of Order 3900.19B. “Technically qualified safety personnel” is defined in paragraph 11h in Order 3900.19B. The categories of mishaps are defined in Block 17. 73 Investigation result
All investigation results shall include a chronological summary of the findings of fact, and a listing of all the causes and conclusions. Consideration should also include any relevant equipment involved, weather conditions, and what protective equipment was used. Also include whether alcohol or drugs were involved, and the number of personnel exposed. Finally, note if appropriate training and PPE was provided, list any pictorial exhibits, and provide any additional descriptive information that was not previously captured in other blocks of the 3900-6 form.
Fig 7-2
Page 129 Chap 7
Figure 7-3 . CHECKLIST OF INFORMATION TO BE RESEARCHED AS PART OF THE
MISHAP INVESTIGATION When preparing an investigation of the mishap/incident, the following should be collected and evaluated … Region, Organizational Routing Symbol … Unit Name … Location of Mishap/Incident … Date and Time of Mishap/Incident … Name of Individual(s) Involved in Mishap/Incident … SSN, Age, Sex … Grade and Job Title … Task assigned during incident (if applicable) … Total experience in the field … Experience in this area … Nature of Injury/Illness … Part of body affected … Severity … Narrative of events, including cause. Also include or consider: … Facility Type … Equipment Involved … Contaminants (if applicable) … Weather (if applicable) … Phase of Operation … Seat belt used? (If applicable) … Was personal protective equipment used? (if applicable) … Was fatigue a factor? … Were drugs or alcohol involved? … Any other human behavior factors involved? … Number of personnel exposed (if applicable) … Did injured party attend safety training? If so, when? … Name of individual operating equipment/vehicle other than injured party … Operator’s total experience … Operator’s total experience with type of equipment/vehicle … Actual Days Off … Actual Days Restricted … Were Forms CA-1, CA-2, and CA-6 completed and processed? … Personnel costs … Government property involved (ID/serial number) and estimated damages … Additional property involved (ID/serial number) and estimated damages … Liability Claimed … Operational days lost … Corrective Action Taken or Planned … Name and Title of individual preparing the report … Report Date … Photographs … Measurements … Interviews of witnesses, and/or employees … Accident/Illness occurs on overtime
Fig 7-3
Chap 9 Page 9-1 Par 900
CHAPTER 9. REPORTS BY EMPLOYEES ON HAZARDOUS CONDITIONS
900. GENERAL. This chapter is a condensed version of 29 CFR 1960.28. Refer to this CFR section if clarification is needed. Employee reports are designed to identify the existence of, or potential for, unsafe or unhealthful working conditions expeditiously. Once identified, the corrective action can be taken and completed. These reports are not to be used as grievances, nor should any employee fear any retribution from filing a legitimate report. Employees who believe an unsafe or unhealthful condition exists in their workplace are encouraged to report these conditions to their supervisor or to the appropriate safety and health official, and to request a workplace inspection. Employees who make a report may request their name be withheld.
CHAPTER 9. REPORTS BY EMPLOYEES ON HAZARDOUS CONDITIONS
901. EMPLOYEE REPORT OF HAZARDOUS CONDITION. Employees may report unsafe or unhealthful conditions either orally or in writing.
a. Process.
(1) The initial report shall be submitted to the immediate supervisor.
(2) The supervisor will notify the OSH professional as designated in the region/center OSH program.
(3) The OSH professional will ensure the report is written and entered into an appropriate log. The log will be provided to AXX-400, AMP-1, or ACT-600 for inclusion in the region/center OSH program documentation.
b. Reports.
(1) Initial report by employee shall contain the following information:
(a) Description of the hazard (include equipment name and system name, if applicable).
(b) Location of the reported unsafe or unhealthful condition.
(c) The employee name or name of the representative of the employee (the report may be submitted anonymously).
(d) Date and time when condition was found.
(e) Other information as deemed appropriate (e.g., suggested corrective action).
(2) Supervisor’s Report.
(a) At a minimum, the initial report from the employee.
(b) Approximate number of employees affected.
(c) Date reported to the supervisor.
(d) Suggested corrective action.
(e) Actions taken/status.
Page 9-2 Chap 9 Par 901
(3) OSH Professional’s Report.
(a) Indicate on the supervisor’s report whether the condition is imminent danger, serious, or other.
(b) Assign a log number to the report.
(4) Log Report.
(a) A file or reference number.
(b) Date and time of receiving a complaint.
(c) Location of the alleged hazardous condition; e.g., facility name, city, and state.
(d) A brief description of the alleged condition.
(e) Hazard classification; e.g., imminent danger, serious, other than serious.
(f) Date and nature of action taken.
c. Timelines.
(1) Imminent danger and serious conditions will be reported immediately.
(2) All others will be reported as soon as possible.
(3) Inspections and employee notification will be performed in accordance with the requirements set in 29 CFR 1960.28. These include the following:
(a) The ROSHM will inspect the workplace within 24 hours for reports of imminent danger conditions; within 3 working days for potentially serious conditions; and within 20 working days for other than serious safety and health conditions. An inspection may not be necessary if, through normal management action, the identified hazardous condition can be abated immediately.
(b) An employee reporting unsafe or unhealthful conditions shall be notified in writing within 15 calendar days if it is determined that no hazards exist and no inspection is planned based on the report. A copy of the notification will be provided to the field OSHECCOM committee. If an inspection or investigation is performed, the results shall be made available to the employee making the report within 15 calendar days after completion of the inspection for safety violations, or within 30 days for health violations.
(c) A copy of the employee reports of hazardous conditions logs for each facility shall be collected by each regional division manager and forwarded to the ROSHM, who shall forward the logs to ANS and AEE by January 15 of each year.
902. ALLEGATIONS OF REPRISAL All employees are protected from coercion, discrimination, or reprisals for filing a report of an unsafe or unhealthful working condition; for participation in the FAA OSH program; or for declining to perform his or her assigned task because of a reasonable belief the task poses an imminent risk of bodily harm or death (see 29 CFR 1960.46(a)). Employees may report allegations of reprisal orally or in writing to the ROSHM (Washington headquarters employees should file reports with ARA). The ROSHM will investigate these allegations and initiate appropriate action in accordance with procedures in the region/center OSH program. A copy of the investigation will be furnished to AEE within 30 days after completion of the investigation for forwarding to the Secretary of Labor.
903-999. RESERVED.
Chap 10 Page 10-1 Par 1000
CHAPTER 10. FALL PROTECTION PROGRAM
CHAPTER 10. FALL PROTECTION PROGRAM
1000. GENERAL. The purpose of a fall protection program is to protect employees working at elevated heights from injuries or death due to a fall. The Department of Labor lists falls as one of the leading causes of traumatic occupational death, and OSHA estimates that there are at least 68,000 fallrelated injuries annually in the construction industry alone. Fall protection standards are outlined in OSHA General Industry Standards under 29 CFR 1910.23 - 1910.29 and in OSHA Construction Standards under 29 CFR 1926, Subpart M, Fall Protection, 29 CFR 1926.104, Safety Belts, Lifelines, and Lanyards, 29 CFR 1926.105, Safety Nets, and 29 CFR 1926.106, Working Over or Near Water. National consensus standards also provide guidelines for technical issues related to fall protection and elevated work surface exposures and associated controls. Figure 10-1, Cross References to OSHA and national consensus standards, contains a cross reference of applicable American National Standards Institute (ANSI) and American Society for Testing and Materials (ASTM) standards to OSHA.
1001. SCOPE. This chapter applies to all FAA personnel. This includes, but is not limited to, personnel performing work on elevated work sites, personnel involved in design and acquisition, etc.
1002. DEFINITIONS.
a. Competent person. A person who, because of training and experience, is capable of providing program oversight. This includes identifying hazardous conditions in personal fall arrest systems or any component thereof as well as in their application and use with related equipment. This person is considered an expert climber, and has a potential exposure to falls due to the complexity of work being performed at these heights.
b. Ladder safety system. An assembly of components whose function is to arrest the fall of a user, including the carrier and its associated attachment elements (brackets, fasteners, etc.), safety sleeve, body support and connectors, wherein the carrier is permanently attached to the climbing face of the ladder or immediately adjacent to the structure.
c. Personal fall arrest system. A system used to arrest an employee in a fall from a working level. It consists of an anchorage, connectors, a body harness, and may include a lanyard, deceleration device, lifeline, or suitable combinations of these.
d. Qualified person. An individual with a recognized degree or professional certificate and extensive knowledge and experience in the subject field, who is capable of design, analysis, evaluation, and specifications in the subject work, project, or product (e.g., structural engineers, designers). This person must be an expert climber if job duties require climbing.
e. Qualified climber. An individual who, by virtue of physical capabilities, training, work experience, and job assignments, climbs standard structures that meet OSHA standards and are equipped with appropriate fall protection to perform routine tasks, and the climber is constantly protected by attachment to a ladder safety device or by a guardrail. This person performs construction activity using ladders and scaffolds below 10 feet.
f. Expert climber. An individual who, by virtue of physical capabilities, training, work experience, and job assignments, climbs standard structures that are not equipped with climbing safety devices; performs work at elevated sites (i.e., platforms, antenna cross members, top or back of radar antennas, etc.) that do not meet OSHA standards for walking/working surfaces; or is required to perform construction activity above 10 feet (i.e., use of portable ladders or scaffolds). This person is considered a qualified climber.
Page 10-2 Chap 10 Par 1003
1003. PROGRAM ELEMENTS. All FAA regions and centers, the NAS Implementation Engineering Center and Service Centers, and other region and center headquarters organizations who have employees exposed to fall hazards shall develop a fall protection program that includes the following elements:
a. Identification of Fall Hazards. Surveys of facilities shall be conducted and documented to identify fall hazards associated with all elevated work areas by persons who have received training and are qualified to identify and recognize such hazards.
b. Hazard Evaluation and Control.
(1) Existing and potential hazards of each elevated work surface shall be identified and procedures established by a competent person to ensure safe working conditions.
(2) Written fall protection procedures shall be developed to address non-routine (based upon employee risk and familiarity with operations) climbing operations or when the use of conventional fall protection systems are not feasible or create a greater hazard in use (e.g., during construction or modification of elevated work areas). The plan shall address applicable procedures like one-person and multi-person climbing operations, requirements for radio and/or telephone communications, special logistics for remote locations, and emergency rescue procedures. Fall protection procedures for construction-related activity must conform with the requirements of 29 CFR 1926.502.
c. Engineering Assessments. All elevated work surfaces shall be designed, constructed, and maintained to ensure that they support their maximum intended load. When surveys identify potential deficiencies with a structure or system, a determination shall be made by a qualified person to ensure that the surface has the strength and structural integrity to support employees working on them. When exposure to a fall hazard cannot be prevented through engineering controls (e.g., platforms, guardrails) or the use of elevated work platforms, fall arrest equipment shall be used. A qualified person shall evaluate modifications or installations of fall arrest systems to elevated work structures to ensure that the fall arrest systems perform as intended.
d. Selection of Equipment.
(1) Selection of fall protection equipment shall be approved by a competent or qualified person. All equipment shall meet applicable OSHA and ANSI standards and must be suitable for the work intended.
(2) Cages and wells. On fixed ladders installed later than 1 year following the effective date of this order, cages and wells are prohibited on fixed ladder installations over 20 feet in length, unless it can be shown by a competent person that they are the only feasible means of protection.
(3) Personal Fall Arrest System (PFAS). Personal fall arrest systems shall meet applicable OSHA and ANSI requirements and shall be selected by competent persons to match the particular work conditions and environment. Full body harnesses shall be worn unless alternative protection is approved by a competent person. Body belts are not acceptable as part of PFAS.
(4) The following factors shall be considered when selecting equipment and systems:
(a) Maintenance requirements.
(b) Performance specifications.
(c) Ease of use and worker productivity.
Chap 10 Page 10-3 Par 1003
(d) Environmental conditions.
(e) Installation (e.g., anchorage points, structural integrity).
e. Maintenance and Inspection.
(1) All equipment and systems shall be inspected and maintained in accordance with manufacturer’s specifications and OSHA and ANSI standards.
(2) Any PFAS with signs of damage, impact loading, or significant component defect shall be withdrawn from service immediately and evaluated for serviceability by a competent person or replaced.
(3) Maintenance and inspection activities shall be documented.
(4) All equipment and systems should be thoroughly inspected before each use.
f. Training and Qualifications.
(1) Employees shall receive training to recognize the hazards associated with elevated work surfaces and fall hazards in their area of operation and the procedures to follow to minimize these. Training shall be conducted by a competent person in accordance with OSHA regulations, ANSI requirements, and the manufacturer’s instructions. The level of training shall be consistent with an employee's job assignment as a qualified climber, expert climber, competent person, or qualified person. Figure 10-2, FAA Elevated Work Surface Job Categories, summarizes requirements for each level of climber.
(2) Refresher training shall be conducted whenever an employee who has already been trained does not have the understanding or demonstrated skill required by this chapter (e.g., due to changes in the workplace or changes in the types of fall protection systems or equipment to be used).
(3) All training shall be properly documented in the agency’s official training information system. Documentation shall include a written certification record that contains the name or other identifier of the employee trained, the date(s) of the training, and the signature of the competent person who performed the training.
(4) Employees shall be physically capable of performing assigned job duties and shall receive medical evaluations consistent with AAM guidance.
g. Emergency Rescue Procedures. Emergency and rescue procedures, consistent with the nature of the operations and the conditions of the elevated space, shall be established to rescue an employee should an emergency occur. Procedures shall include methods for summoning rescue and emergency services, for rescuing employees from heights, and for providing necessary medical services in a timely fashion.
h. Facilities, Systems, and Equipment Acquisitions. Fall protection requirements shall be incorporated as early as possible in all design, construction, renovation, maintenance, and other projects and programs. New facilities shall have fall protection meeting OSHA requirements built in to the system (e.g., approved tie-off points are permanently identified prior to commissioning). A qualified person or a competent person and, as appropriate, planners and engineers shall ensure designs and plans properly indicate location and type of fall arrest systems to be installed and that approved tie-off points are permanently identified prior to commissioning.
Page 10-4 Chap 10 Par 1003
i. Contracts.
(1) All contracts issued for work involving elevated surfaces must contain a provision that contractors must have a fall protection program in accordance with OSHA and state requirements. Safety programs shall be submitted in accordance with contract requirements.
(2) Contractors must provide their own appropriate fall arrest equipment and training. FAA will not issue fall protection equipment to contractors.
Chap 10 Page 10-5 Figure 10-1
Figure 10-1. CROSS REFERENCES TO OSHA & NATIONAL CONSENSUS STANDARDS
Subject Area OSHA Standard 29 CFR National Consensus Standard Ladders 1910.25 Portable Wood Ladders 1910.26 Portable Metal Ladders 1910.27 Fixed Ladders
Figure 10-1. CROSS REFERENCES TO OSHA & NATIONAL CONSENSUS STANDARDS
ANSI A14.1, Safety Requirements for Portable Wood Ladders ANSI A14.2, Safety Requirements for Portable Metal Ladders ANSI A14.3, Safety Requirements for Fixed Ladders ANSI A14.4, Safety Requirements for Job- Made Ladders ANSI A14.5, Safety Requirements for Portable Reinforced Plastic Ladders Step Bolts and Manhole Steps
1910.27 Fixed Ladders ASTM C478, Specifications for Precast Reinforced Concrete Manhole Sections ASTM A394, Specifications for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners Stairs 1910.24 Fixed Industrial Stairs ANSI A64.1, Requirements for Fixed Industrial Stairs Ramps and Bridging Devices
1910.30 Other Working Surfaces 1910.37 Means of Egress, General
ANSI MH14.1, Industrial Loading Dock Levelers and Dockboards
Work Surfaces 1910.23 Guarding Floor and Wall Openings and Holes
ANSI A58.1, Minimum Design Loads for Buildings and Other Structures ANSI A12.1, Safety Requirements for Floor and Wall Openings, Railings, and Toeboards Scaffolds 1910.29 Manually Propelled Mobile Ladder Stands and Scaffolds (towers) 1910.28 Safety Requirements for Scaffolds
ANSI A92.1, Manually Propelled Mobile Ladder Stands ANSI A10.8, Safety Requirements for Scaffolds Mobile Elevating Work Platforms, Mobile Ladder Stands, and Powered Industrial Truck Platforms
1910.66 Powered Platforms for Building Maintenance 1910.67 Vehicle-Mounted Elevating and Rotating Work Platforms
ANSI A92.3, Manually Propelled Elevating Work Platforms ANSI A92.1, Manually Propelled Mobile Ladder Stands
Page 10-6 Chap 10 Figure 10-1
Subject Area OSHA Standard 29 CFR National Consensus Standard Fall Protection Systems
1926 Subpart M, Parts: 1926.500 Scope, Application, and Definitions 1926.501 Duty To Have Fall Protection 1926.502 Fall Protection Systems Criteria and Practices
1926.503 Training 1926.105 Safety Nets 1926.106 Working Over or Near Water 1910 Standards: 1910.23 Guarding Floor and Wall Openings and Holes 1910.24 Fixed Industrial Stairs 1910.27 Fixed Ladders 1910.28 Safety Requirements for Scaffolding 1910.67 Vehicle-Mounted Elevating and Rotating Work Platforms 1910.268 Telecommunications
ANSI A10.11, Construction and Demolition Operations - Personnel and Debris Nets ANSI A10.14, Requirements for Safety Belts, Harnesses, Lanyards, Lifelines, and Drop Lines for Construction and Industrial Use ANSI A12.1, Safety Requirements for Floor and Wall Openings, Railings, and Toeboards ANSI A39.1, Safety Requirements for Window Cleaning ANSI Z359.1, Safety Requirements for Personal Fall Arrest Systems, Subsystems, and Components
Chap 10 Page 10-7 Figure 10-2
Figure 10-2. FAA ELEVATED WORK SURFACE JOB CATEGORIES How to use this table: Read down the duties column and then select the category furthest down the table in which the employee has one or more duties. That is the minimum level of job category to which the employee must be trained.
CATEGORY DUTIES PREREQUISITES Qualified Climber: Is a person who performs any of the duties specified for this category and has successfully completed the Qualified Climber training
Climbs structures that are 50 feet or less in height. Structures meet OSHA standards. Maintenance tasks performed. Climber always be protected by attachment to a ladder safety device or guardrail.
Expert Climber: Is a person who performs any of the duties specified for this category. Then, after meeting the prerequisites identified, has successfully completed Expert Climber training. Note: He/she may also be assigned duties specified for the Qualified Climber.
Maintenance tasks performed. Structures more than 50 feet in height. Structure may not meet OSHA standards. Performs construction work, if job duties require regardless of height. Conducts basic elevated work surface inspections, if job duties require.
Physically capable Has successfully completed Qualified Climber training
Competent Person: Is a person who performs any of the duties specified for this category. Then, after meeting the prerequisites identified, has successfully completed Competent Person training. He/she may also be assigned duties specified for the Qualified and/or Expert Climber categories.
Provides program oversight, if job duties require. Selects equipment and systems, if job duties require. Inspects fall protection equipment and systems, if job duties require. Heavy exposure to falls; majority of work performed at heights, if job duties require.
Physically capable Has successfully completed Qualified Climber training Has successfully completed Expert Climber training, if job duties require climbing Qualified Person: Is a person who performs any of the duties specified for this category. Then, after meeting the prerequisites identified, has successfully completed Qualified Person training. He/she may also be assigned duties specified for the Qualified Climber and/or Expert Climber and/or Competent Person categories.
May have program oversight, if FAA employee. Degreed (i.e., structural or equivalent engineering degree) or holds professional certification in fall protection-related disciplines. Extensive knowledge. Capable of design, analysis, and evaluation. Develops specifications related to work on elevated surfaces and the associated fall protection systems.
Physically capable Has successfully completed Qualified Climber training Has successfully completed Expert Climber training, if job duties require climbing Has successfully completed Competent Person training
Chap 11 Page 11-1 Par 1100
Continue reading ↓ 120 of 493 passages shown