Radar Vectors
FAA Order Cancelled Issued Oct 28, 2015 AJI-2 308 pages Copy saved Nov 18, 2026

Order JO 3120.4P Air Traffic Technical Training - Change 1

This order conveys instructions, standards, and guidance for the administration of air traffic (AT) technical training.

This document is no longer current. Cancelled by JO 3120.4R. Check the official source before relying on it.

Official source ↗ Open PDF

Text read by OCR from a scanned file (1 of 308 pages). Check the original, as some words may be misread.

Distribution: Electronic Initiated By: AJI-0

CHANGE U.S. DEPARTMENT OF TRANSPORTATION JO 3120.4P

CHG 1 FEDERAL AVIATION ADMINISTRATION

Effective Date: National Policy May 24, 2018

Air Traffic Technical Training SUBJ:

1. Purpose. This change incorporates policies from Federal Aviation Administration (FAA) Notices JO 3120.151, Air Traffic Technical Training at Special Event Temporary Control Towers, dated June 1, 2017; JO 3120.152, En Route Front Line Manager (FLM) Training Requirements, dated September 28, 2017; and the approved, but unpublished, notice to change Appendix B, Instructions for Completing FAA Form 3120-25, ATCT/ARTCC OJT Instruction/Evaluation Report.

Changes to Form 3120-25 and associated instructions resulted from a collaborative decision to focus attention on Air Traffic Organization (ATO) Top 5 safety issues such as misapplication of Instrument Flight Rules/Visual Flight Rules (IFR/VFR) conflict resolution, weather issuance, and Pilot Report (PIREP) solicitation/distribution during on-the-job-training. These changes add a new paragraph (5e) in Chapter 4, which addresses En Route FLM training requirements; a new Chapter 7, impacting technical training at special event temporary control towers; and a revised Appendix B, providing instructions for use of the newly updated on-the-job training report form.

2. Who This Change Affects. This change applies to ATO personnel and anyone using ATO air traffic training directives.

3. Disposition of Transmittal. Retain this transmittal until it is superseded by an order revision.

PAGE CHANGE CONTROL CHART Remove Pages Dated Insert Pages Dated ii-v 10/30/2015 ii to vi 05/24/2018 4-5 – 4-7 10/30/2015 4-5 – 4-8 05/24/2018 7-1 – 7-4 05/24/2018 B-1 to B-15 10/30/2015 B-1 – B-15 05/24/2018

05/24/2018 JO 3120.4P CHG 1

4. Administrative Information. Direct questions to the Training Policy and Programs Group (Air Traffic), AJI-24.

Jeffrey U. Vincent Acting Vice President Safety and Technical Training

ORDER JO 3120.4P Air Traffic Organization Policy

Effective Date:

10/30/2015

SUBJ: Air Traffic Technical Training

This order prescribes instructions, standards, and guidance for the administration of air traffic technical training. All persons involved in air traffic technical training are required to be familiar, and comply with, this order. Facilities must be in compliance with this order within 90 days of the effective date.

Terry Biggio Vice President, Safety and Technical Training Air Traffic Organization

Distribution: Electronic Initiated By: AJI-0 Safety and Technical Training

05/24/2018 JO 3120.4P CHG 1

ii

TABLE OF CONTENTS

Explanation of Changes … EC-1

Chapter 1. General Information … 1-1

1. Purpose of This Order … 1-1

2. Audience … 1-1

3. Where Can I Find This Order? … 1-1

4. What This Order Cancels … 1-1

5. Explanation of Policy Changes … 1-1

6. Background … 1-1

7. Location of ATC Training Courseware … 1-1

8. Word Meanings … 1-1

Chapter 2. Roles and Responsibilities … 2-1

1. ATO Safety and Technical Training (AJI) … 2-1

2. Service Units (Air Traffic Services, System Operations) … 2-1

3. FAA Academy … 2-1

4. Facility Personnel … 2-1

Chapter 3. Technical Training … 3-1

1. Identification of Training Requirements … 3-1

2. Changes, Modifications, and Waivers … 3-1

3. Interpretations to JO 3120.4 … 3-1

4. New Training Requirement … 3-1

5. Development of Training … 3-1

6. Call for Training … 3-1

7. Educational Opportunities for Non-FAA Personnel … 3-1

8. Radar Approach Control (RAPCON)/Radar Air Traffic Control Facility (RATCF) Training … 3-1

Chapter 4. Training Requirements for Air Traffic Control Specialists … 4-1

1. Initial Qualification Training … 4-1

2. Field Qualification Training … 4-1

3. Enrollment in Terminal Basic Radar Training (Course 50034) … 4-2

4. Weather Observers … 4-2

05/24/2018 JO 3120.4P CHG 1

iii

5. Proficiency Training … 4-3

6. Remedial Training … 4-6

7. Recertification Procedures … 4-6

8. Recertification Hours … 4-7

Chapter 5. Training and Proficiency Records and Reports … 5-1

1. Policy … 5-1

2. Responsibilities … 5-1

3. Training Reports … 5-1

4. Disposition of Records and Reports … 5-2

Chapter 6. Air Traffic Control Specialist On-the-Job (OJT) Training and Position

Certification … 6-1

1. General … 6-1

2. Facility Training Hours … 6-1

3. OJT and Position Certification … 6-1

4. Training Plan … 6-4

5. Performance Skill Checks … 6-4

6. Certification Skill Checks … 6-4

7. Suspension of Training … 6-6

8. Additional OJT Hours … 6-6

9. Training Review Process … 6-6

10. OJT and Certification Process Flowchart … 6-8

Chapter 7. Air Traffic Control Specialist Special Event Tower

Training Requirements … 7-1

1. General … 7-1

2. Roles and Responsibilities … 7-1

3. Special Events/Temporary Control Tower Specialist Training Requirements … 7-1

4. Special Event/Temporary Control Tower Documentation and Record Retention … 7-4

Appendix A. Instructions: Training and Proficiency Record (FAA Form 3120-1) … A-1

1. General .... … A-1

2. Section I. Employment Data … A-3

3. Section IIA. Air Traffic Certificates … A-3

4. Section IIB. Air Traffic Ratings … A-4

05/24/2018 JO 3120.4P CHG 1

iv

5. Section III. Qualification Training … A-5

6. Section IV. Equipment Certification … A-11

7. Section V. Proficiency (Recurrent, Refresher, Supplemental, Skill Enhancement), and Remedial Training … A-11

8. Section VI. Technical Appraisal … A-14

9. Section VII. Management and Other Training … A-14

10. Section VIII. Liaison Familiarization Travel … A-16

11. Section IX. Certified TRAX Records … A-16

Appendix B. Instructions: ATCT/ARTCC OJT Instruction/Evaluation Report

(FAA Form 3120-25) … B-1

1. Section 1. Introduction … B-1

2. Section 2. Using the Form … B-1

Appendix C. Instructions: FSS OJT Instruction/Evaluation Report

(FAA Form 3120-26) … C-1

1. Section 1. Introduction … C-1

2. Section 2. Using the Form … C-1

Appendix D. En Route Instructional Program Guide … D-1

1. Section 1. Introduction … D-1

2. Section 2. Stage 1: FAA Academy Training … D-2

3. Section 2A. Air Traffic Basics (En Route) … D-2

4. Section 2B. Initial En Route Training … D-2

5. Section 3. Stage 2: Assistant Controller Training (Flight Data) … D-4

6. Section 4. Stage 3: Non-radar and Radar Associate Controller Training … D-8

7. Section 5. Stage 4: Radar Controller Training … D-33

Appendix E. Flight Service Instructional Program Guide … E-1

1. Section 1. Introduction … E-1

2. Section 2. Stage 1: Initial Flight Service Training … E-2

3. Section 2A. Air Traffic Basics (Flight Service) … E-2

4. Section 2B. Flight Service Initial Training … E-4

5. Section 3. Stage 2: Facility Flight Service Training, Facility or Area Qualification/Certification … E-8

6. Section 3A. Area Knowledge … E-9

7. Section 3B. Flight Data … E-22

05/24/2018 JO 3120.4P CHG 1

v

8. Section 3C. NOTAM … E-23

9. Section 3D. Preflight … E-24

10. Section 3E. Inflight … E-25

11. Section 3F. Weather Observer … E-26

12. Section 3G. Broadcast … E-27

Appendix F. Terminal Instructional Program Guide … F-1

1. Section 1. Introduction … F-1

2. Section 2. Stage 1: FAA Academy Training … F-2

3. Section 2A. Air Traffic Basics (Terminal) … F-2

4. Section 2B. Initial Tower Cab Training … F-3

5. Section 2C. Terminal Basic Radar Training … F-4

6. Section 2D. TRACON Skill Enhancement Workshop … F-5

7. Section 3. Stage 2: Flight Data Position Training … F-6

8. Section 4. Stage 3: Clearance Delivery Position Training … F-11

9. Section 5. Stage 4: Ground Control Position Training … F-20

10. Section 6. Stage 5: Local Control/Cab Coordinator Position Training … F-35

11. Section 7. Stage 6: Non-Radar Training … F-47

12. Section 8. Stage 7: Radar/Handoff/Coordinator Controller Training … F-64

Appendix G. Traffic Management Instructional Program Guide … G-1

1. Section 1. Introduction … G-1

2. Section 2. Stage 1: FAA Academy Training … G-1

3. Section 3. Stage 2: Facility Traffic Management Qualification and Certification … G-3

4. Section 4. Instructions for Completing the TMC OJT Instruction/Evaluation Report FAA Form 3120-32 … G-6

Appendix H. Terminal and En Route Facility Controller-in-Charge Instructional Program Guide … H-1

1. Section 1. Introduction … H-1

2. Section 2. Stage 1: FAA Academy Training … H-1

3. Section 3. Stage 2: Facility Controller-in-Charge Qualification and Certification … H-3

4.Section 4. Stage 3: Facility Controller-in-Charge … H-5

5. Section 5. Instructions: CIC OJT Instruction/Evaluation Report (FAA Form 3120-36 … H-7

Appendix I. Reserved for OCEAN21 … I-1

vi

05/24/2018 JO 3120.4P CHG 1

Appendix J. Instructions for Completing the OJTI Candidate Abilities and Attributes Report, FAA Form 3120-148 … J-1

Appendix K. Definitions … K-1

Appendix L. Acronyms … L-1

Explanation of Changes

Explanation of Changes

Background: This order prescribes instructions, standards, and guidance for the administration of air traffic technical training. FAA Order JO 3120.4P has been created to reflect updates and changes in procedural and technical requirements for air traffic controller training.

General: Many changes are editorial and administrative in nature, including clarification of existing standards and guidance, typographical errors, resolution of formatting errors, and inaccurate and/or outdated information and terms.

Recent reorganization to Service Units also updated.

Chapter 1: Paragraph 7. The name of the repository for national courseware was renamed to ATC Training Courseware.

Chapter 2: Roles and responsibilities for Director of Technical Training (AJI-2), Air Traffic Manager (ATM), and Training Administrator (TA) modified to reflect organizational changes within the ATO.

Paragraph 1. Added annual requirement for AJI-2 to solicit facility best practices, responsive to OIG Report AV-2013-121, Recommendation 2.

Paragraph 4.a.(4) Removed requirements for contract training. (7) Added requirement for annual evaluation report for Tower Simulator System (TSS) from ATMs at Hub TSS facilities. (8) Removed requirement to notify regional office of pending change in status of Limited Aviation Weather Reporting Station (LAWRS).

Paragraph 4.b.(6) Added requirement to ensure National Training Database (NTD) is populated.

Chapter 4: Paragraph 1. Added new hire language and new Table 4-1 to reflect current Agency hiring practices. Subparagraph b, changed All Sources, General Public, or another “entry level,” to “All Sources – No Experience.”

Paragraph 2. Deleted “e. En Route and Terminal controllers entering the Traffic Management option should attend initial traffic management qualification training as soon as practical.” Deleted references to Academy graduates, VRAs, RMCs.

Paragraph 4. Weather Observers: Revised language in sub-topics, including new course numbers.

Paragraph 5.a. Recurrent Training: New language to clarify requirements. Removed requirement to identify Recurrent topics by October 1 to be delivered following year. Removed wake turbulence and line up and wait (LUAW) from Recurrent topics.

Paragraph 5.b. Refresher Training: Removed requirements for Land and Hold Short (LAHSO) and tower visibility procedures and markers. Realigned airspace intruder training topic to fall under Refresher Training topic (1), including airspace intruder and Domestic Events Network notification requirements.

Paragraph 5.b.(12) Changed requirement for Refresher Training simulation to include facilities with access to simulation capabilities.

Paragraph 5.d.(1) and (2) Skill Enhancement Training: Clarified FLM/STMC must identify training to be administered, rather than develop training. Changed “will” to “must”.

Paragraph 6.b. Clarified FLM/STMC must “identify” training, rather than “develop” training. Changed “will” to “must”.

Paragraph 7.a. Weather Observer Recertification: Removed references to National Weather Service (NWS).

Chapter 5: Paragraph 1.c. Added language to change the retention of entries in FAA Form 3120-1 Section V (Proficiency Training) and Section VIII (Liaison Familiarization Travel) to 5 years.

Chapter 6: Paragraph 2.a: Changed language to clarify FLM may suspend OJT, not training.

Paragraph 3.a.(1): Removed Note reference Air Traffic Assistants, FV-2154, providing OJT.

Paragraph 3.a.(2) Note 1: Clarified that a transferring OJTI must have worked the position involved for a minimum of 60 hours after certification prior to conducting OJT.

Paragraph 3.d. Note: Clarified that OJTI certification is only applicable to the facility/area in which the certification was conducted.

Paragraph 3.e: Added requirement that yearly evaluation of OJTI must include debrief, responsive to Independent Review Panel (IRP) Recommendation 36.

Paragraph 3.f: Added language to encourage OJTIs to contact Local Safety Councils for best practices.

Paragraph 7: Suspension of Training: Changed language to clarify FLM/STMC may suspend OJT, not training.

Paragraph 9.a.(1)(b): Training Review Process: Changed “Support Manager/OM”

to “second level manager or above”.

Paragraph 10: Added language describing Figure 6-1 that was inadvertently dropped during previous update to order, clarifying the flowchart is an abbreviated version of the OJT process and not a substitute for policy set forth in the order.

Appendices: All reformatted and renumbered for consistency.

Appendix A: Paragraph 1.j: Removed requirement to enter Section III notation that “surveillance approaches not conducted in this facility”.

Paragraph 7. Section V. Proficiency Training: Added language to change the retention of entries in Section V to 5 years.

Paragraph 9. Section VII. Management and Other Training: Added sentence that training completed by eLMS need not be entered in this section.

Paragraph 10. Section VIII. Liaison Familiarization Travel: Added language to change the retention of entries Section VIII to 5 years.

Appendix B: Block 11, a. (2) Fixed inadvertent error in “Needs Improvement” language, changed to match previous L version of this order. Block 14 added language that employees can add attachments for comments.

Appendix C: Section 2. Updated Figure C­ 1, Form 3120-26 to reflect removal of En Route Flight Advisory Service (EFAS) and Maintenance Job Tasks.

Section 3. Updated Figure C-2 to align existing positions with Job Subtasks.

Updated position Job Task, Job Subtask, and Indicators to reflect removal of EFAS and

Maintenance Job Tasks and reflect current practices.

Appendix D: Section 3. Stage 2. Paragraph 2. Prerequisite amended to read, “Successful completion of Initial En Route (Course 50148001 or current course) or individual meets direct entry qualifications established for specific hiring source.” Paragraph 6.b: Removed phase references to national lesson plans. Updated lesson plan 6 to current title.

Section 4. Stage 3. Paragraph 6.a.(1): Removed training requirement for ATC Review (ES-7-1).

Paragraph 6.a.(5): Added Cold Temperature Compensation to examples of additional requirements as identified by the facility.

Paragraph 6.b.(1). Removed phase references to national lesson plans.

Paragraph 7.a.(1): Removed phase references to national lesson plans. Updated lesson plans 50 and 55 to current titles. Added requirement for Unmanned Aircraft Systems (UAS) training.

Paragraph 7.a.(2) Changed DARC operations to backup system operations.

Section 5. Stage 4. Paragraph 6.a. Removed phase references to national lesson plans. Updated lesson plans 1, 3, 4, 14, and 15 to current titles. Added requirement for Time Based Flow Management (TBFM) training. Paragraph 6.b.(1), deleted “HOST.”

Paragraph 7.e.(2) Added to Vectoring complexity factor examples: VFR aircraft, TBFM, responsive to Corrective Action Request (CAR)-2012-003.

Paragraph 7.e.(8): Added to Service to VFR aircraft complexity factor examples: safety alerts, vectors, responsive to CAR-2012­ 003.

Paragraph 7.e.(18): Added Traffic Management Initiatives to complexity factor examples.

Paragraph 10.b.: Changed sentence to read, “Developmentals/CPC-ITs must receive a minimum of one hour of instruction on backup systems (e.g. VTABS, EBUS, BUEC, Emergency PTT, Guard, Standby transmitters, etc.), as determined by the TA, prior to certification on the first radar sector.”

Appendix E: Section 2B. Updated course number of Flight Service Initial Training. Removed Course 57511 prerequisite. Prerequisite changed for Initial FS training due to new hiring process and change of terms.

Changed references from Block to Module, where applicable.

Paragraph 1. Module 1 title changed to Introduction. Module 2 title changed to Weather Analysis and updated sub-topics. Module 3 title changed to Weather Radar Interpretation and updated sub-topics. Module 4 title changed to Satellite Interpretation and updated sub-topics. Module 5 title changed to Flight Plan Processing and updated sub-topics. Module 6 title changed to Broadcast and Weather Briefing Basics and updated sub-topics. Module 7 title changed to Preflight and updated sub-topics. Module 8 title changed to Inflight and updated sub-topics. Module 9 removed references to direction finder (DF) equipment. Module 10 title changed to Search and Rescue and updated sub-topics. Module 11 title changed to NOTAMs and updated sub-topics. Module 12 title changed to Weather Transmit and Data Edit and updated sub-topics: a. amended to read, “Provides students with an introduction to weather data retrieval, data entry and editing weather and Service B messages.” Module

13 title changed to Combined Lab Exercises and updated sub-topics.

Paragraph 2. Evaluation. a. Updated evaluations in (1) through (5) and sub-topic b.

Section 3. Stage 2. Added bullet for OASIS Specialist Training. Deleted bullet “En Route Flight Advisory Service (EFAS) (Course 55247): OJT for position qualification and certification to perform EFAS duties at the Flight Watch position. This course is available but not required for facility certification.”

Section 3F. Weather Observer. Updated language to remove references to National Weather Service (NWS). Updated Course 60004715 references.

Section 3H. Deleted entire section.

Appendix F: Section 2B. General: Removed references to Performance Verification (PV). Evaluation: Updated evaluation criteria to current process.

Section 2C. Introduction to Radar Control (Course 50055001) removed, unique content from this course is covered in Course 50043 (Basics) and Course 50034 (Terminal Basic Radar).

Section 2C. Terminal Basic Radar Training. Prerequisite: Changed to current process. Added current evaluation criteria.

Section 2D. “1. General:” amended to read, “This workshop provides advanced training for developmentals/CPC-ITs assigned to Level 9, 10, 11, and 12 radar facilities.” Updated Prerequisite to reflect new hiring practices.

Section 3. Stage 2. Paragraph 2.b. and c: Added UAS and TBFM training to list of nationally-developed training.

Section 5. Stage 4. Administration: Removed reference to contractor-supported training. Changed Note 2 to include towers with access to Tower Simulation Systems (TSS). Added Note 3 which clarifies responsibility for determining facilities that have access to TSS. Renumbered previous Note 3 to Note 4.

Paragraph 4.c.(9): Removed reference to Microwave Landing System (MLS).

Section 6. Stage 5. Administration. Changed Note 2 to include towers with access to TSS. Added Note 3 which clarifies responsibility for determining facilities that have access to TSS.

Section 6. Stage 5. Paragraph 1.b. (11) Replaced with Cold Temperature Compensation, if applicable. Previous (11) was removed as briefing requirement already covered in b.(1)(d).

Section 7. Stage 6. Paragraph 2.a: Corrected inaccurate national-developed lesson plans (1) through (10).

Paragraph 4.c.(1): Added (h) VFR/IFR, responsive to CAR-2012-003.

Section 8. Stage 7. Administration. Note 2. Changed language to clarify facilities with access to high-fidelity simulators.

Paragraph 2.e.(3): Changed language from “Provide VFR traffic advisories” to “Provide VFR traffic advisories and VFR/IFR separation”, responsive to CAR­ 2012-003.

Appendix G. Updated TMS to National Traffic Management Specialist (NTMS) throughout appendix.

Section 3. Stage 2. 55116 PART A. Added new prerequisite for certification of at least 2 control positions at the facility. Training

Content: Added (e) TBFM nationallydeveloped training course, as applicable.

Stage 2. 55116 PART B. Job Function. Added duties of the Arrival and Departure Coordinator in sub-topic k.

Appendix K: Added definition for Comprehensive Electronic Data Analysis and Reporting (CEDAR). Added definition for Simulation Fidelity. Removed definition of Performance Verification (PV) Process, and Air Traffic-Collegiate Training Initiative (AT-CTI).

Chapter 1. General Information

Chapter 1. General Information

1. Purpose of This Order. This order conveys instructions, standards, and guidance for the administration of air traffic (AT) technical training.

2. Audience. This order applies to all Air Traffic Organization (ATO) personnel, and anyone using ATO directives.

3. Where Can I Find This Order? You can find this order on the MyFAA employee website. Select “Orders & Notices” in the “Tools & Resources” drop down menu. Or use one of these links:

• http://www.faa.gov/regulations_policies/orders_notices/ • https://employees.faa.gov/tools_resources/orders_notices/ • http://faa.gov/air_traffic/publications

4. What This Order Cancels. JO 3120.4N, Air Traffic Technical Training, dated September 30, 2013, and all changes to it are canceled.

5. Explanation of Policy Changes. See page EC-1 in the previous section.

6. Background. JO 3120.4P is an update that reflects changes in procedural and technical requirements for AT technical training.

7. Location of ATC Training Courseware. ATC Training Courseware is located at: http://inet.atctraining.faa.gov/

8. Word Meanings.

a. “Must” means an action is mandatory.

b. “Should” means an action is recommended.

c. “May” means an action is permitted.

d. “Will” is used only to indicate futurity, not a requirement.

e. Singular words include the plural, plural words include the singular.

Chapter 2. Roles and Responsibilities

4. Facility Personnel. › a. Air Traffic Manager (ATM).

1. ATO Safety and Technical Training (AJI). AJI is responsible for developing an integrated technical training strategy to lead, direct, and guide the overall design, management, and delivery of technical training. AJI also develops policies and standards for ATO technical training.

The Director of Technical Training (AJI-2). AJI-2 is responsible for program guidance, effectiveness, technical accuracy, evaluation of air traffic technical training, coursework/curriculum development and review, maintenance, and oversight of national and FAA Academy-delivered courses. AJI-2 will solicit facility training best practices and conduct an annual review of this order, with stakeholder participation, no later than July 1 each year.

2. Service Units (Air Traffic Services, System Operations). Service units are responsible for implementation, administration, and evaluation of the AT technical training program.

3. FAA Academy. The FAA Academy supports the administration of the national AT Technical Training Program.

4. Facility Personnel. Facility personnel involved in AT technical training must maintain a comprehensive working knowledge of the procedures and guidelines outlined in this order and the applicable national and local training directives.

a. Air Traffic Manager (ATM). The ATM must ensure:

(1) Where authorized, a Support Manager is assigned the responsibilities of the Training Administrator (TA). Where no Support Manager is authorized, an individual is designated in writing to serve as the TA. The ATM may serve as the TA without written designation.

(2) A training program is established for certification and proficiency and is conducted in accordance with national, service area and local directives, and Instructional Program Guides (IPG).

Note: The ATM is encouraged to develop, if feasible, local collaborative training workgroups.

(3) The training program is described in a facility training directive.

(4) Individuals who conduct instructor-led training and/or develop lesson plans attend the Facility Instructor Training course (Course 10501 or equivalent), as soon as possible. The On-the-Job Training Instructor (OJTI) course does not satisfy this requirement.

Note: This training should occur within 6 months.

(5) FAA Form 3120-1 is initiated and maintained (see appendix A).

(6) Resource requirements necessary to conduct the facility training program are submitted to the appropriate service center or flight services (FS) information office. The service center may submit resource requirements to the service unit.

4. Facility Personnel. › b. TA.

(7) Tower Simulator Systems (TSS) Hub Facilities. An annual calendar year evaluation of the usage and effectiveness of the TSS is conducted, and a written report is forwarded to the Director, AJI-2, no later than March 1 of the following year. The report must be sufficiently detailed to identify the TSS hours used to satisfy proficiency and qualification training requirements. The report may also include recommendations for the usage and/or effectiveness of the TSS, facility-specific issues and initiatives, and other related data. Input from facilities that have access to the Hub TSS is mandatory. A sample report is available from AJI-2.

(8) For On-The-Job Training (OJT) and Certification:

(a) Individuals entering qualification training receive facility orientation and are briefed on the IPG contents that are pertinent to the current stage of training, facility training directive, and other associated directives prior to entering training.

(b) OJT is accomplished in accordance with this order.

(c) Training reports are properly completed and maintained.

(d) Facility target hours, minimum certification hours, and On-the-Job Familiarization (OJF) hours are established, maintained, and updated.

(e) All OJTIs and managerial personnel meet the qualification criteria in this order.

(f) OJTIs are recommended and designated in accordance with chapter 6.

(g) The training review process for non-supervisory personnel is conducted in accordance with this order.

(9) If training is unsuccessful, action is taken in accordance with Human Resources Policy Manual (HRPM) Volume 1: Employment (HRPM EMP) -1.14a., Collective Bargaining Agreement (CBA), and/or other directives.

(10) All information including national and local training orders and directives is made available to all facility personnel.

(11) Training teams receive support of the TA and Support Managers.

(12) Evaluate developmental/Certified Professional Controller-in-Training (CPC-IT) performance on a simulation scenario(s) when requested by the TA.

b. TA. The TA must:

(1) Administer the facility training program.

(2) Ensure that the facility training program is planned, conducted, assessed, and revised on a continuous basis.

(3) Administer the training contract at the local level.

(4) Ensure local course materials, visual aids, and control scenarios are developed, properly labeled, and continually updated to ensure technical accuracy.

4. Facility Personnel. › e. FLM/STMC.

(5) Maintain training documentation.

(6) Ensure the National Training Database (NTD) is populated.

(7) Plan and direct the training of personnel involved in the OJT/certification process.

(8) Attend the AT Facility Training Administration course (course 50310 or current course) as soon as possible after occupying the position.

c. Support Specialist. The Support Specialist assists in the administration of facility training.

d. Operations Manager (OM)/Traffic Management Officer (TMO). The OM/TMO provides oversight and direction to Front Line Managers (FLMs)/Supervisory Traffic Management Coordinators (STMCs) to ensure compliance with training directives and goals.

e. FLM/STMC. The FLM/STMC administers OJT, and identifies, and assigns Proficiency Training. The FLM/STMC (or as identified in the local training directive) must:

(1) Ensure OJTI qualifications are met.

(2) Ensure OJTIs have no other duties to perform during training sessions.

(3) Maintain currency and/or familiarization on positions where certifications are conducted.

(4) Conduct Performance and Certification Skills checks.

(5) Ensure OJT is conducted and documented in accordance with this order.

(6) Ensure position certification documentation is complete and logged on FAA Form 3120-1.

(7) Ensure FAA Form 3120-25/26/32/36, or its electronic equivalent, is signed.

(8) Serve as the training team lead.

(9) Make the final determination to amend an individual’s training plan.

(10) Make the final determination regarding certification.

(11) Make the determination regarding suspension of OJT.

(12) Address any reported extenuating circumstances that may impede the training progress of the developmental/CPC-IT/Traffic Management Coordinator in Training (TMC­ IT)/Full Performance Level in Training (FPL-IT).

4. Facility Personnel. › g. Developmental/ CPC-IT/ TMC-IT/ FPL-IT.

f. OJTI. The OJTI is responsible:

(1) To teach, coach, and demonstrate techniques to apply AT procedures. OJT instruction must be based on handbook requirements and procedures. It must also provide guidance on control judgment.

(2) To ensure that OJT includes preferred methods of teaching through a combination of instruction, demonstration, and practical application.

(3) To document and discuss/debrief each training session on FAA Form 3120­ 25/26/32/36, or electronic equivalent.

(4) For each training session conducted during the assigned shift, at least one OJT report for each position/consolidated position must be completed by each OJTI. It is permissible to combine reports if the OJTI trains the same developmental/CPC-IT/TMC-IT/FPL-IT on the same position on the same day. The OJTI must be:

(a) Plugged-in the same control position as the developmental/CPC-IT/TMC-IT/ FPL-IT when OJT is conducted.

(b) Responsible for all positions combined during training, even if the developmental/CPC-IT/TMC-IT/FPL-IT is certified on one or more of the positions that are combined.

g. Developmental/CPC-IT/TMC-IT/FPL-IT. The developmental/CPC-IT/TMC-IT/FPL­ IT must be physically and mentally prepared to receive OJT, exercise initiative, and study to ensure satisfactory training progress. They must be active participants in their training to achieve certification. The developmental/CPC-IT/TMC-IT/FPL-IT must:

(1) Perform operational assignments in order to maintain proficiency and currency.

(2) Review, discuss, and make suggestions to enhance the training plan with the other members of the training team.

(3) Ensure that all aspects of the training plan are understood.

(4) Review, discuss, and sign FAA Forms 3120-25/26/32/36, or their electronic equivalents.

(5) Immediately advise an FLM/STMC of any extenuating circumstance(s) that might impede training progress.

(6) Verify that all OJT/OJF times are recorded accurately.

(7) Engage in OJT only on positions that have been assigned.

(8) Be receptive to training performance feedback.

Chapter 3. Technical Training › 8. Radar Approach Control (RAPCON) or Radar Air Traffic Control…

Chapter 3. Technical Training

1. Identification of Training Requirements. National technical training requirements are established at the Headquarters (HQ) Service Unit Level: Air Traffic Services, System Operations (Flight Service Stations (FSS) and the David J. Hurley Air Traffic Control System Command Center (ATCSCC)). Technical training requirements are developed and implemented in collaboration with AJI.

2. Changes, Modifications and Waivers. Changes, modifications, and waivers to national training courses or this order must be submitted in writing to the Director of Technical Training (AJI-2), through the Service Center training managers and/or Headquarters of any Service Unit. Waiver renewal requests must be submitted to the Service Center 60 days prior to the expiration date. Unless otherwise specified, waivers are valid for 2 years, and will be signed by AJI-0.

Note: Requests may be submitted electronically with electronic signatures.

3. Interpretations to JO 3120.4. All requests for interpretations to this order must be forwarded to AJI-2, through the Service Center training managers.

Note: Requests may be submitted electronically with electronic signatures.

4. New Training Requirement. Requests for the development of new national courses/curricula must be submitted to AJI-2.

5. Development of Training. AJI-2 will take action to establish and maintain training programs for identified requirements using an Instructional Systems Design (ISD) process. Briefing items developed for controller information/awareness only are excluded from ISD requirements.

6. Call for Training. The ATO must identify organizational training requirements for inclusion in the annual call for training.

7. Educational Opportunities for Non-FAA Personnel. In accordance with national policy, orientation, familiarization, shadowing, or other educational opportunities may be provided at FAA facilities. Educational opportunities for individuals not employed by the FAA will be provided in accordance with FAA agreements and/or memoranda of understanding.

Note: The provisions of JO 3120.4 may or may not apply to federal or non-federal contract towers and FSSs. Training at FAA contract towers and FSS must be conducted in accordance with each contractor’s FAA-approved training plan.

8. Radar Approach Control (RAPCON) or Radar Air Traffic Control Facility (RATCF) Training. Military personnel assigned to jointly staffed approach control facilities must be provided training on radar control positions under FAA supervision.

a. To participate in radar control training, military personnel must possess an appropriate certificate (AC Form 8060-1, Control Tower Operator (CTO) Certificate; FAA Form 7220-1, Air

Traffic Control Specialist Certificate; or AC Form 8080-2, Airman Written Exam Report). Military personnel must meet FAA certification and currency requirements.

b. Training must be documented in FAA Form 3120-1 (see appendix A). All military participants who have successfully completed the training program must receive appropriate FAA certificates and ratings to be qualified for assignment to control positions under general supervision.

Chapter 4. Training Requirements for Air Traffic Control Specialists › 2. Field Qualification Training.

Chapter 4. Training Requirements for Air Traffic Control Specialists

1. Initial Qualification Training. The newly hired developmental must successfully complete initial qualification training for the selected option. Table 4-1 identifies the specific initial training requirements based on the hiring source (i.e., the type of vacancy announcement).

a. AT Basics (Courses 50043, 50043001, 50143, or 50243 or current course) is prerequisite to qualification training, as prescribed herein and in the Instructional Program Guide for the specific option.

b. Individuals hired under All Sources – No Experience job announcement, who satisfy any of the criteria specified below, may elect to skip AT Basics:

(1) Individual has completed courses that cover the required AT Basics objectives, OR

(2) Individual holds, or has previously held, an FAA-recognized AT Certification. These include the CTO certificate and facility certifications and/or ratings at military air traffic control facilities.

Table 4-1: Initial Qualification for New Hires

Hiring Source Initial Training Requirement

All Sources-No Experience • Required to successfully complete AT Basics course conducted at the FAA Academy. Employee may request to bypass with documented education or experience prior to onboarding.

• Required to successfully complete initial qualification training conducted at the FAA Academy for the appropriate option.

All Sources - Experience • Enter appropriate stage of field training at the facility based on experience.

2. Field Qualification Training. CPC-IT, FPL-IT, TMC-IT, and developmentals must receive qualification training at field facilities as outlined in this order and in facility directives. Qualification training must be conducted in accordance with the IPGs contained in this order.

a. CPCs transferring from the En Route option to the Terminal option or from the Terminal option to the En Route option need not attend initial qualification training for the new option or facility type at the FAA Academy. The specialist will be entered into the appropriate stage of field training as determined by the receiving facility ATM.

b. CPCs transferring from the tower-only option to a combined tower/Terminal RADAR Approach Control (TRACON) or TRACON-only option are required to complete Course 50034 or current course.

c. CPCs transferring from a tower to a tower or combined tower/TRACON to another combined facility or from a TRACON to a TRACON will be entered into the appropriate stage of field training as determined by the ATM.

Chapter 4. Training Requirements for Air Traffic Control Specialists › 4. Weather Observers.

d. En Route developmentals changing to a Terminal option, Terminal developmentals changing to the En Route option, and Terminal developmentals changing to a different facility type must attend initial qualification training for the new option or facility type.

e. En Route, Terminal, and Traffic Management controllers changing to the FS option who have not previously completed the FS initial training must enter FS training at the appropriate training facility.

f. FSS specialists changing to the En Route or Terminal option must complete initial qualification training identified for the option at the FAA Academy. A FSS specialist who has successfully completed either Terminal or En Route initial qualification training at the FAA Academy must be entered into the appropriate development stage of the training program as determined by the receiving facility ATM.

3. Enrollment in Terminal Basic Radar Training (Course 50034 or current course). Enrollment is limited to developmentals/CPC-ITs assigned to, or selected for, TRACON facilities, who have not been radar-certified at the CPC level at an FAA facility. Developmentals/CPC-ITs at visual flight rules (VFR) towers are not eligible to attend Course 50034. Developmentals/CPC-ITs at towers that meet the criteria to provide radar services must complete the Terminal Radar Qualification examination and the appropriate portions of Stage 7, Radar Control Training (see appendix F, Terminal Instructional Program Guide) as part of local control certification.

4. Weather Observers. Air Traffic Control Specialists (ATCS) at facilities that have weather observer responsibilities must:

a. Successfully complete Course 60004715 (LAWRS) and pass the Certification Examination contained in Course 60004715 with a score of 70 percent or greater.

b. ATCSs must receive at least 5 hours of OJT that includes operation of the weatherobserving equipment used at the facility, and complete a minimum of 5 observations.

c. In order to retain certification, the ATCS must complete one official or practice observation recorded on an MF1M-10C within the past 60 days.

d. ATCSs at facilities required to augment an Automated Surface Observing System (ASOS) or an Automated Weather Sensor System (AWSS) must:

(1) Successfully complete weather observer training and certification.

(2) Complete Course 57005 (ASOS) or Course 57089 (AWSS). OJT is required on the actual ASOS/AWSS equipment prior to completion of training.

(3) In order to retain this certification, the ATCS must be logged on the position

5. Proficiency Training. › b. Refresher Training.

responsible for ASOS/AWSS for at least 1 hour or complete one manual official or practice observation recorded on an MF1M-10C within the past 60 days.

Note: If only a portion of Courses 57005 or 57089 is required to meet the specific needs of the facility, only the portion(s) actually completed must be recorded on FAA Form 3120-1.

5. Proficiency Training. Proficiency Training is required for all personnel who maintain currency. This training includes Recurrent, Refresher, Supplemental, and Skill Enhancement. Training needs will differ from facility to facility, and should be tailored to meet identified requirements. All Proficiency Training must be documented on the employee’s FAA Form 3120­ 1, or electronic equivalent. When Recurrent Training is prescribed, AJI must provide instructions for its applicability, and specific instructions for documentation in FAA Form 3120­ 1 or electronic equivalent.

a. Recurrent Training. Recurrent Training is conducted via an 8-hour block of training, two rounds delivered yearly. Each round is comprised of approximately 4 hours of training typically selected from the topics listed below, and 4 hours of training on relevant and timely safety topics. The following items need not be duplicated in local Refresher Training:

(1) Safety alerts and traffic advisories, to include Minimum Safe Altitude Warning (MSAW) procedures and the relationship between charted minimum altitudes and underlying topography.

(2) Weather and other conditions that affect flight (e.g., icing, thunderstorms, wind shear, and VFR aircraft that encounter instrument flight rules (IFR) conditions).

(3) Bird activity information and dissemination.

(4) Runway Safety.

(5) Recovery in ATC Operations.

(6) Fatigue awareness.

b. Refresher Training. Each facility must maintain, in writing, an annual (calendar year) Refresher Training plan. Annual Refresher Training contains two elements: nationally and/or facility-developed curriculum and simulation training. Facilities are encouraged to review their quality control data (e.g., Quality Control Monitoring, Service Reviews, and Compliance Verification and data available in the Partnership for Safety Portal) to identify additional topics for annual Refresher Training in order to meet each facility’s changing needs. The following topics must be included unless designated by the TA as not applicable:

(1) Unusual situations, lost aircraft orientation, aviation security procedures (e.g., interceptor procedures and communications, Domestic Events Network (DEN) notification requirements), hijacking, airspace intruders, and other topics identified by the TA (Training on emergency situations should be based on real-life incidents and aircraft accidents, stressing a lessons-learned approach).

Note: Terminal and En Route personnel must receive lost aircraft orientation on an annual basis; FS personnel must receive lost aircraft orientation on a quarterly basis.

(2) Seldom-used procedures, such as transitioning to and applying non-radar separation and procedures for special flight handling.

(3) Facility procedures for Go Arounds and Missed Approaches (Towers only).

(4) Local airport de-icing plans (LADP).

(5) All certified weather observers who augment an ASOS or AWSS must receive at least semiannual LAWRS training, and at least annual training on the operator input device (OID). The LAWRS training should include, but is not limited to, seasonal changes, visibility markers, adverse weather situations, and common data entry errors. Observers who take manual observations must receive annual LAWRS training.

Note: The OID training may consist of a retake of individual sections of CBI Course 57005/57089 or current courses, as appropriate.

(6) Procedures and responsibilities for special use airspace (SUA)/special activity airspace (SAA). This training must include, but is not limited to, a review of military training routes (MTR) and the types of operations conducted on any MTR beginning in, passing through, or terminating within the controllers’ area of responsibility.

(7) Primary Backup Mode. Terminal personnel required to maintain radar currency must receive training on the use of the primary backup mode. All En Route personnel required to maintain currency must receive training on the use of the primary backup mode at Air Route Traffic Control Centers (ARTCCs) when and where applicable. This training must include:

(a) Transitioning to and from normal operations to backup operations.

(b) The unique radar/flight data processing used while operating in the backup configuration(s).

(c) Control and communication procedures associated with operation in the backup mode.

(8) En Route Decision Support Tool (EDST). When an area of specialization exclusively utilizes EDST, facilities must conduct training on the transition to/from an EDST environment to paper strips. Training with the paper strips must focus on the identification of possible aircraft conflictions, as well as strip marking procedures.

(9) Managerial Personnel/Controller-In-Charge (CIC). Operational Managers and CICs must receive a minimum of 1 hour of training and include the handling of accidents, incidents, unusual situations, upward reporting, Domestic Events Network (DEN) notification, and emergency events.

(10) Air Traffic Organization Operational Contingency Plan, in accordance with JO

5. Proficiency Training. › c. Supplemental Training.

05/24/2018 JO 3120.4P CHG 1

1900.47, ensures familiarity with procedures and airspace based on facility contingency plans (e.g., loss of radar, communications failure).

(11) Facilities that use Ocean21 (O21) must conduct annual training on the transition to/from the O21 environment to paper strips (dual channel failure procedures). Training with paper strips must focus on the identification of possible aircraft conflicts as well as strip marking procedures.

(12) Facilities with access to simulation capabilities such as AT Coach, ETG, Test Target Generator (TTG), TSS, Test and Training Laboratory (TTL), SIMFAST, and O21 lab must complete locally identified, evidence-based simulation training on the topics identified in paragraph 5.b., Refresher Training, deemed appropriate by the TA, a minimum of two hours of evidence-based simulation training per calendar year.

Note 1: CBI is not an acceptable form of simulation to satisfy the above requirements.

Note 2: ATMs/District Managers are expected to support the use of high fidelity simulators (e.g. ETG, TSS, TTL, O21) to the fullest extent possible. The Terminal District Manager, in coordination with AJI-2, is responsible to determine which facilities have access to the TSS.

c. Supplemental Training. All operational personnel must complete supplemental training prior to the use of new or revised procedures, regulations, or equipment. The TA must review all supplemental training and update local training materials as appropriate.

(1) EN ROUTE. Prior to first assumption of watch supervision duties for an out-of-area assignment, as described in FAA Order JO 7210.3, Facility Operation and Administration, paragraph 2-6-2(i), FLMs must have the required training and knowledge to effectively manage the operation. Facility training directives must include, as a minimum, the following:

(a) Training on:

i. Airspace

ii. Maps

iii. Equipment

iv. Letters of Agreement

v. Standard Operating Procedures

vi. General topics as assigned by the facility, such as resource management, overtime assignments, occupational safety, and flight data responsibilities

(b) Familiarity time requirements regarding:

i. Area OMs, Peer FLMs, and area workforce

ii. Operations (Traffic Flows/Sys Ops, SWAPs, Playbooks)

5. Proficiency Training. › d. Skill Enhancement Training (SET).

05/24/2018 JO 3120.4P CHG 1

iii. Contingency Plans

iv. Reference Guides on:

• Best Practices

• Airspace configurations

• Automation adaptations to include communications and airspace

• Satellite facility hours of operation

• Special Use Airspace

• Military operations

d. Skill Enhancement Training (SET). The purpose of SET is to improve an individual’s knowledge, skills, and abilities. SET may be assigned to individuals certified on at least one position. SET may not be used to correct deficient performance that resulted in decertification. For an individual not certified but training on at least one position, SET may be assigned to enhance specific skills, techniques, or knowledge, to assist in their success with the training program. SET may also be the result of an Event Review Committee (ERC) recommendation.

Note: SET is not the same as an Individual Performance Management (IPM) Operational Skills Assessment (OSA). OSA procedures are in JO 3400.20, Individual Performance Management (IPM) for Operational Personnel.

(1) SET for CPC/FPL/TMC.

(a) The FLM/STMC must assign SET in writing to include the specific skills and requirements necessary to accomplish this training.

(b) The FLM/STMC is responsible for determining the methods to be used in the training. Training must be tailored to meet the individual’s needs. Methods may include OJT, CBI, instructor-led training, self-directed study, and simulation. Evaluations may be used in SET if appropriate.

(c) SET must be documented on FAA Form 3120-25/26/32/36 or its electronic equivalent.

(d) SET must be documented in Section V of FAA Form 3120-1.

Note 1: If subsequent observation of performance indicates that the SET did not produce the expected results, further action may be required, such as Performance Skill Checks or Remedial Training.

Note 2: Record ATSAP SET as Type 4 training on FAA Form 3120-1 under Major Subject Areas as “ATSAP.” If an OJT form or electronic file, such as a CEDAR file, is used to

7. Recertification Procedures. › a. Weather Observer Recertification.

05/24/2018 JO 3120.4P CHG 1

document the ATSAP SET, those forms or files must be destroyed or deleted once successfully completed.

(2) SET for developmental/CPC-IT/TMC-IT/FPL-IT:

(a) The FLM/STMC must assign SET in writing. The written assignment must include the specific skills and requirements necessary to accomplish this training.

(b) The FLM/STMC is responsible for identifying the training to be administered to the specialist. Training must be tailored to meet the individual’s needs. Methods may include CBI, instructor-led training, self-directed study, and simulation (SET for developmentals may not include OJT; evaluations may be used in SET, if appropriate).

(c) SET must be documented on FAA Form 3120-25/26/32/36 or its electronic equivalent.

6. Remedial Training. The purpose of Remedial Training is to correct documented performance deficiencies. Remedial Training is mandatory if the individual has been decertified as a result of performance deficiencies. When an individual’s performance is deficient but the individual has not been decertified, Remedial Training may be conducted.

a. The FLM/STMC must assign Remedial Training in writing. The written assignment must include the specific area(s) to be covered and the reasons.

b. The FLM/STMC is responsible for identifying the methods to be used in the training. Training must be tailored to meet the individual’s needs. Methods may include, but are not limited to, CBI, instructor-led training, self-directed study, simulation, evaluation, and OJT.

c. Training provided as a result of performance deficiency must be documented as Remedial Training. When documenting Remedial Training due to a performance-related decertification, references must not be made to a reported occurrence in Section V.

Note: Although not presently defined as Proficiency Training, Remedial Training is still recorded in Section V of FAA Form 3120-1 and logged under Proficiency Training in TRAX. This requirement may change with the development of new tracking mechanisms.

7. Recertification Procedures. Personnel who fail to meet currency requirements and those who are decertified on one or more operational position(s) must be recertified prior to resuming operational duties. To be recertified, the specialist must demonstrate, under direct supervision, the ability to satisfactorily perform operational duties during normal workload conditions. Recertification may be accomplished by individual position or a single action covering multiple positions at the discretion of the ATM or designee. If recertification is not achieved, the ATM or designee must take action in accordance with Agency guidelines.

a. Weather Observer Recertification. To recertify as a weather observer, personnel who have not taken an observation within 60 days must demonstrate proficiency to an FLM or their designee. Personnel who have not taken an observation within 90 days must retake the weather observer certification exam. Recertifications due to a performance deficiency must be entered on

Chapter 4. Training Requirements for Air Traffic Control Specialists › 8. Recertification Hours.

05/24/2018 JO 3120.4P CHG 1

FAA Form 3120-1, Section VI, Technical Appraisal. All other recertifications must be recorded on FAA Form 3120-1, Section III, Qualification Training.

b. Pilot Weather Briefer. Individuals certified as pilot weather briefers must comply with the proficiency check requirements established by the FAA and outlined in JO 7220.4, FAA Certification of Pilot Weather Briefing and En Route Flight Advisory Service.

c. Documentation. FAA Form 3120-25 or FAA Form 3120-26, FSS OJT Instruction/Evaluation Report, must be used to document recertification. Instructions for completing these forms are found in appendices B and C. Traffic Management Recertification(s) must be recorded on FAA Form 3120-32. Instructions for completing this form are found in appendix G. Recertification(s) must be recorded on FAA Form 3120-1, Section III. Recertification due to a performance deficiency must be entered on FAA Form 3120-1, Section VI, Technical Appraisal.

8. Recertification Hours. At the discretion of the TA, personnel who have worked an operational position within the last 120 days may be recertified and returned to operational duties without additional training. Prior to recertification evaluation, they may receive training including but not limited to instructor-led training, simulation training, and/or OJT. OJT hours must not exceed 25 percent of the target hours established for developmentals with no previous experience.

a. Personnel who have not worked an operational position in the last 120 days, but have done so in the last year, must receive instructor-led training, simulation training, and OJT prior to recertification. OJT hours must not exceed 50 percent of the target hours established for developmentals with no previous experience.

b. Personnel who have not worked an operational position for a year or more must receive instructor-led training, simulation training, and OJT prior to recertification. OJT hours must not exceed the target hours established for developmentals with no previous experience.

Chapter 5. Training and Proficiency Records and Reports › 3. Training Reports.

Chapter 5. Training and Proficiency Records and Reports

1. Policy.

a. An FAA Form 3120-1, or its electronic equivalent, will be prepared for each ATCS individual and will be maintained as a permanent part of the employee’s training file. It must be used to record the results and the completion of training requirements for each qualification course, Proficiency Training, and other agency-approved courses. Employment data as well as AT certificates and ratings must also be documented in the record. The guidance contained in appendix A must be followed when making entries on FAA Form 3120-1, which is governed by the provisions of the Privacy Act of 1974.

b. For reporting purposes, the terms “student/trainee/developmental/CPC-IT/TMC-IT/FPL-IT” apply to anyone receiving training at the specialist, instructor, or supervisory level.

c. Entries in Sections V and VIII of FAA Form 3120-1 may be disposed of five years after the training occurs.

d. A facility may maintain sections of FAA Form 3120-1 outside of the orange jacket of the form. When sections are kept outside the orange jacket for accessibility of initialing, etc., precautions must be taken to ensure that the provisions of the Privacy Act and other record-maintenance requirements are met. Precautions must be taken to ensure that there is no mixing or confusing of the records.

e. Documentation of training received should be the same at a temporary and a permanent AT facility, with the following necessary variations at the temporary facility:

(1) No entries are necessary in sections I and IIA.

(2) Section IIB entries must include “(TEMPORARY)” after the name of the facility.

(3) Section III entries should correctly reflect that the training was completed, either in separate development stages/positions or as a single action (all positions combined).

(4) If no three-character identification is assigned to the facility, enter the full name in the “FAC IDENT” column.

(5) Make entries in sections IV through VIII only if appropriate to the operations.

2. Responsibilities.

a. The ATM or designee must be responsible for initiating and maintaining the employee’s FAA Form 3120-1.

b. FAA Academy, Air Traffic Division (AMA-500), must operate as a field facility for the purposes of this directive with respect to FAA Form 3120-1 management and administration.

3. Training Reports. A training report must be completed on the appropriate FAA OJT Instruction/Evaluation form for OJT sessions and simulated/simulation scenarios. Reports

Chapter 5. Training and Proficiency Records and Reports › 4. Disposition of Records and Reports.

reflecting certifications must contain the signature of the certifying official. Examples of the FAA forms and specific instructions regarding completion of training reports are contained in the appendices of this order and in facility training directives.

4. Disposition of Records and Reports.

a. Training documents (e.g., Training Plans, FAA Forms 3120-25/26/32/36, etc.) may be disposed of after certification on each position or, for the En Route option, after certification on each sector (e.g., D6/R6). Exception: Reports reflecting position certifications, re-certifications prior to being facility rated, and all written and performance-based examinations required by the IPG must be retained for 1 year after the employee is facility rated. Prior to these documents being disposed of, they should be offered to the employee.

b. In the event of a termination of employment due to a training failure, all training records, reports, training plans, etc., must be retained at the facility for a period of 1 year. After 1 year, if appropriate, they must be handled in accordance with national directives and JO 1350.14B; Records Management or current order.

Note: Procedures for record disposition may vary from service area to service area. Therefore, reference should be made to service area supplements regarding this process.

c. FAA Forms 3120-25/26/32/36 utilized for CPC/FPL/TMC recertification may be disposed of after the recertification has been documented with all appropriate signatures on the Training and Proficiency Record, FAA Form 3120-1, section III or TRAX.

d. Upon termination of employment, except for training failures, FAA Form 3120-1 must be forwarded to the appropriate Human Resource Management office.

e. The service area office may require retention of records beyond the periods specified above because of special circumstances (e.g., litigation, appeals, etc.). In these cases, facilities must comply with service area office instructions.

Chapter 6. Air Traffic Control Specialist On-the-Job Training (OJT) and Position Certification

3. On-the-Job Training (OJT) and Position Certification › a. Selection of OJTIs.

1. General. This chapter establishes requirements and procedures for standardization of instruction and evaluation of the OJT and position certification process.

2. Facility Training Hours. Each facility must establish target hours, minimum certification hours, and OJF hours for each operational position within the facility. Cross-sectional work groups will be used to recommend these hours. Evaluate established hours at least annually and, if necessary, adjust the hours. Facility training hours must be categorized based on the level and type of previous Air Traffic Control (ATC) experience. (e.g., those with no previous experience, employees transferring from like-type facility to like-type facility, employees transferring from lower level to higher level or high level to lower facility, etc.).

a. The employee’s FLM/STMC or designee may suspend OJT prior to completing all of the allotted target hours.

b. The FLM/STMC will ensure that OJT is productive and appropriate for the experience level of the developmental/CPC-IT/TMC-IT/FPL-IT.

c. When identified in the local training directive, ATMs may authorize training on consolidated/combined positions.

(1) OJT time may be allotted between the consolidated/combined positions based on traffic activity, as determined by the OJTI.

(2) If the developmental/CPC-IT/TMC-IT/FPL-IT is certified on one or more of the routinely consolidated/combined position(s) as identified in the local training directive, the total amount of OJT time must be allotted to the position on which the developmental/CPC-IT/TMC­ IT/FPL-IT is not certified.

3. OJT and Position Certification.

a. Selection of OJTIs. To be eligible to be selected as an OJTI, individuals must not be a management official, and must meet the following criteria:

(1) Certified at the CPC/TMC/FPL level.

(2) Certified a minimum of 12 months on positions involved.

Note 1: Transferring CPC-ITs/TMC-ITs/FPL-ITs with previous OJTI experience on the same type position are exempt from this. However, they must have worked the position involved for a minimum of 60 hours after certification prior to conducting OJT. The 60-hour requirement may be waived at the ATM’s or designee’s discretion for non-control positions.

Note 2: At ATC-8 or below facilities having a developmental/CPC-IT to CPC ratio of greater than 35 percent, the ATM or designee may select OJTIs for Flight Data (FD), Clearance

3. On-the-Job Training (OJT) and Position Certification › g. Training Teams.

Delivery (CD), and Ground Control (GC) once the individuals have been certified on the position for 6 months.

(3) Recommended by the employee’s FLM/STMC, per FAA Form 3120-148, OJTI Candidate Abilities and Attributes Report (appendix J).

b. Selection Panel. The ATM or designee will designate a panel to recommend OJTI candidates. The panel is composed of a minimum of two people, including any participant identified in current collective bargaining agreement(s). The panel must consider, at a minimum, the nominee’s performance, human relation skills, motivation, attitude, and objectivity. They must forward a recommendation to the ATM or their designee for their selection.

c. OJTI Training Requirements. Prior to being assigned OJTI duties, the selected individual must successfully complete the FAA Air Traffic OJTI course or OJTI Cadre course. Completion must be documented on FAA Form 3120-1, section VII.

d. OJTI Certification. To be certified as an OJTI, the employee’s FLM/STMC must directly observe the OJTI’s performance during their first OJT session. The FLM/STMC must document the certification. Certification must be entered on the employee’s FAA Form 3120-1, section III.

Note: OJTI Certification is only applicable for the facility/area in which the certification was conducted. If a CPC-IT/TMC-IT/FPL-IT transfers to another facility/area, an OJTI certification is required for the new facility/area. A transferring CPC-IT/TMC-IT/FPL-IT is not required to retake the FAA Air Traffic OJTI course or OJTI Cadre course.

e. OJTI Evaluation. Once yearly, an FLM/STMC must conduct an evaluation of OJTIs while they are performing OJTI duties, to include debrief. If the last evaluation occurred more than 12 months ago, an OJTI evaluation must be conducted within 30 days of resuming OJTI duties. The evaluation(s) must be documented as skill checks on the employee’s FAA Form 3120-1, section VI.

f. OJTI Best Practices. OJTIs are encouraged to share and review best practices, lessons learned, and optimum training techniques with their Local Safety Councils.

g. Training Teams. The FLM/STMC must establish a training team for the employee they are assigned. The training team must facilitate the training of the developmental/CPC-IT/TMC­ IT/FPL-IT by continuously assessing training progress and providing feedback. In order to meet individual and/or facility needs, the specific individuals on this team may change as the developmental/CPC-IT/TMC-IT’s/FPL-ITs training progresses.

(1) The training team must consist of:

(a) The employee’s FLM/STMC.

(b) At least two and no more than three OJTIs.

Note: Only one OJTI is required for a TMC-IT.

(c) The developmental/CPC-IT/TMC-IT/FPL-IT.

(d) Other person(s), as assigned by the ATM or designee.

(2) The FLM/STMC must:

(a) Act as the training team leader.

(b) Direct training by modifying the training plan as required.

(c) Facilitate training team functions and seek support of facility management and staff personnel when necessary.

(d) Review all training documentation and consider input from all training team

members.

(e) Identify and assign SET as needed.

(f) Provide feedback to include, but not limited to, an identification of strengths, weaknesses, and specific recommendations to improve performance to the training team.

(g) Ensure that performance feedback is provided to the developmental/CPC­ IT/TMC-IT/FPL-IT as soon as possible after each OJT session.

(3) The training team must:

(a) Develop and review the training plan and recommend modification to the developmental’s/CPC-IT’s/TMC-IT’s/FLP-IT’s FLM/STMC.

(b) Conduct training team meetings to ensure plan objectives are met in accordance with local directives.

(c) Make recommendations on the training progress and readiness for certification based on training history and observation of performance during simulation (if practical).

(d) Determine the operational positions for which OJF is required. OJF is required on at least two operational positions.

(e) Conduct the majority (51 percent or more) of OJT.

(f) When an identified training team member is unavailable to provide OJT, another OJTI may provide training.

(g) Provide performance feedback as soon as possible after OJT session(s) to include strengths, weaknesses, and specific recommendations.

(h) The OJTI must be plugged-in to the same position. Direct monitoring must be used when conducting OJT.

Chapter 6. Air Traffic Control Specialist › 6. Certification Skill Checks.

4. Training Plan. The employee’s FLM/STMC must ensure the training plan is developed and documented in writing before beginning OJT. The training plan(s) must include, but is not limited to, operational positions requiring OJF, training objectives, team members, positions, target hours, and minimum certification hours. Operational positions requiring OJF and the assignment of OJF hours are determined in local directives. OJF should be accomplished before beginning OJT and documented on FAA Forms 3120-25/26/32/36. Modifications to the training plan will be documented and discussed with the training team. Retention of training plans and all modifications must be in accordance with national directives and JO 1350.14B, Records Management or current order.

5. Performance Skill Checks. Performance skill checks must be used to assess the developmental/CPC-IT’s/TMC-IT’s/FPL-IT’s training progress and identify job task(s) that require improvement to achieve certification. Direct monitoring must be used when conducting performance skill checks. Performance skill checks may be performed on consolidated/combined position(s)/sector(s) only if training occurred on these consolidated/combined position(s)/sector(s).

Performance skill checks do not count toward OJT hours. Performance skill check(s) must:

a. Occur within the first 30 days after OJT begins, and then at least every calendar month on each position for which the developmental/CPC-IT/TMC-IT/FPL-IT is receiving OJT.

b. Be conducted by a FLM/STMC who maintains familiarity or currency on the operational position(s)/sector(s). Performance skill checks will normally be conducted by the employee’s FLM/STMC or as specified in the local training directive. If the FLM/STMC only maintains familiarity on an operational position/sector, an OJTI must be plugged-in at the same position/sector with the developmental/CPC-IT/TMC-IT/FPL-IT and the OJTI is responsible for the position/sector.

c. Be documented on FAA Form 3120-25/26/32/36, or its electronic equivalent, to include a description of performance and any specific feedback/recommendations. After consideration of previous performance during OJT, performance demonstrated during the skill check session, recommendations resulting from the skill check session and input from other training team members, the FLM/STMC will take one of the following actions: continuation of OJT, SET, suspension of OJT, or recommend a certification skill check. (A recommendation for certification skill check may occur only if the developmental/CPC-IT/TMC-IT/FPL-IT has completed minimum certification requirements).

6. Certification Skill Checks. Certification Skill Checks are an assessment used to determine if an individual demonstrates the knowledge and skill level necessary to certify on an operational position. Certification skill checks must be conducted on operational position(s)/sector(s) by the employee’s FLM/STMC or as identified in the facility’s training directive. Direct monitoring must be used when conducting certification skill checks.

Prior to conducting the certification skill check, the individual must be informed, a review of the training documentation must be conducted, and input from the training team should be considered. The assessment may require more than one session on the position.

Certification skill checks may be supplemented with verbal and/or written questions, simulation, or other methods. They may be performed on consolidated/combined position(s)/sector(s) only if training occurred on these consolidated/combined position(s)/sector(s). A certification on consolidated/combined position(s)/sector(s) certifies the employee on each of the individual position(s)/sector(s). Certification skill checks do not count toward OJT hours. Certification skill checks may be substituted for the monthly required performance skill checks identified above in paragraph 5. Position/Sector certification(s) must be documented on FAA Form 3120-1.

a. Certification skill checks must:

(1) Be conducted upon completion of assigned target hours.

(2) Be conducted upon completion of additional OJT hours if assigned.

(3) Be conducted by a FLM/STMC who maintains familiarity or currency on the operational position(s)/sector(s). If the FLM/STMC only maintains familiarity on an operational position/sector, an OJTI must be plugged-in at the same position/sector with the developmental/CPC-IT/TMC-IT/FPL-IT. The OJTI is responsible for the position/sector.

b. Certification skill checks may be:

(1) Conducted prior to completing target hours if minimum certification hours have been met.

(2) Conducted prior to exhausting the total additional hours if assigned.

(3) At facilities without FLM/STMC’s, the ATM/District Manager or their designee must perform the certification skill check.

c. The employee’s FLM/STMC, or as identified in the local training directive, may certify the individual or suspend OJT.

(1) For a certification skill check to result in certification, all applicable job subtasks must be rated as satisfactory or not observed. If a job subtask(s) are not observed during this assessment, the FLM/STMC must document that the developmental/CPC-IT/TMC-IT/FPL-IT has demonstrated satisfactory performance/knowledge for that job subtask through verbal/written questions, simulation, or other methods.

(2) After the certification skill check, the employee’s FLM/STMC must consider the following items prior to taking the appropriate action:

(a) The developmental’s/CPC-IT’s/TMC-IT’s/FPL-IT’s performance during OJT.

(b) The performance demonstrated during the certification skill check session.

(c) The recommendation(s) resulting from the certification skill check session.

(d) Input from other training team members.

Chapter 6. Air Traffic Control Specialist › 9. Training Review Process.

(3) The results of the certification skill check must be documented on FAA Forms 3120­ 25/26/32/36, or its electronic equivalent, and must include a description of performance and a recommendation for one of the following: certification, continuation of OJT, SET, or suspension of OJT.

7. Suspension of OJT. Suspension of OJT is an action taken by the developmental’s/CPC­ IT’s/TMC-IT’s/FPL-IT’s FLM/STMC or designee to temporarily stop OJT. There is no requirement to exhaust target hours and/or any additional OJT hours prior to suspension of OJT. The developmental/CPC-IT/TMC-IT/FPL-IT must be notified in writing of the documented performance deficiencies. OJT may be suspended without conducting a performance skill check. A training review must be conducted.

8. Additional OJT Hours.

a. Not guaranteed.

b. An OM/TMO, second level manager, or the ATM may assign additional OJT hours in cases where there is an expectation that certification will be accomplished within the additional period.

c. Additional hours must not exceed 20 percent of the target hours.

d. Review of training documents and consideration of input from the training team must be accomplished prior to the assignment of additional training hours.

e. There is no requirement to exhaust additional OJT hours.

f. Upon the completion of additional assigned OJT hours, a certification skill check must be conducted. The employee’s FLM/STMC must take one of the following actions:

(1) Certification, or

(2) Suspension of OJT.

g. Additional OJT hours must be documented in section III of FAA Form 3120-1.

9. Training Review Process. The purpose of the training review process is to ensure that opportunities for training success were utilized while maintaining the integrity of the training program. Training reviews must be conducted when requested by an ATM/District Manager, or when training has been suspended due to performance.

a. A training review must:

(1) Be conducted by a minimum of two individuals from any of the following, as assigned by the ATM/District Manager or their designee:

(a) A FLM/STMC other than the employee’s FLM/STMC. (If not available onsite, the District Manager may assign this duty to any FLM/STMC within the district.)

(b) A 2nd Level Manager or above at the facility where this position is staffed. (If not available onsite, the District Manager may assign this duty to any 2nd Level Manager or above in the District).

(c) TA/Support Specialist. (If not available onsite, the District Manager may designate any of these individuals from within the District.)

(2) Include a participant as designated by a collective bargaining agreement.

(3) Include an assessment of the training history on the position.

(4) Not include members of the training team.

(5) Provide a written statement of facts and recommendation to the ATM/District Manager. The document should include as a minimum, but is not limited to, the following:

(a) The trainee’s performance deficiencies.

(b) Actions the facility has taken to correct the trainee’s performance deficiencies.

(c) Whether or not training was conducted in accordance with JO 3120.4.

(d) Whether or not the trainee adhered to his/her responsibilities.

(e) Consistency of training (number of OJT hours per day, per week or per month, also number of OJTIs involved).

(f) Any extenuating circumstances.

(g) Recommendation (i.e., continuation of OJT or termination of training).

b. Training review may:

(1) Conduct interviews of the training team members and/or other individuals.

(2) Request information from the training team or other individuals.

c. ATM/District Manager must consider the training review’s statement of facts and recommendations when making their final determination for continuation or termination of training. The employee will be notified in writing of the Manager’s decision as soon as possible but not later than 30 days from the date of the suspension of OJT.

Note: If the ATM/District Manager assigns additional OJT hours, the number of hours/days must be finite. The provisions of chapter 6, section 8, Additional OJT Hours, are not applicable.

Chapter 6. Air Traffic Control Specialist › 10. OJT and Certification Process Flowchart.

10. OJT and Certification Process Flowchart. The flowchart in Figure 6-1 is an abbreviated version of the process that provides a general overview of the basic steps involved in the OJT and certification process. It is not intended as a complete description of the OJT and certification process, or as a substitute for the policy set forth in this order. The flowchart is intended to assist in the understanding of the OJT and certification process. Paragraph numbers have been included in the flowchart to reference the location of specific policy information in the body of the order.

Figure 6-1: OJT and Certification Process

Establish training team

(6.3.g)

Document training plan

(6.4)

Provide OJF

Provide OJT

Conduct performance

skill check

(6.5)

Conduct certification

skill check

(6.6)

Ready for certification?

Certified?

Continue OJT

Provide SET

(4.5)

Suspend OJT

Certify

Continue OJT

Provide SET

(4.5)

Suspend OJT

Provide additional OJT

hours if appropriate

(6.8)

Conduct training review

(6.9)

YES

NO

YES

NO

Chapter 7. › 3. Special Events/Temporary Control Tower Specialist Training…

05/24/2018 JO 3120.4P CHG 1

Chapter 7. Air Traffic Control Specialist Special Event Tower Training Requirements

1. General. Those assigned to Special Event Temporary Control Towers must complete the required training described in this chapter prior to performing safety-related air traffic control services at the temporary location. “Special Event Temporary Control Tower” refers to an operation that provides qualified personnel and equipment for the purpose of air traffic control services at a specified site for a period less than 120 days. These operations may include temporary tower deployments in support of aerial demonstrations, fly-ins, sporting events, both natural and man-made disasters, and similar events.

2. Roles and Responsibilities. Air traffic operational personnel involved in Special Event Temporary Control Towers must maintain a comprehensive working knowledge of the procedures and guidelines outlined in this order and other applicable national directives.

a. The Special Event Temporary Control Tower Air Traffic Manager must ensure that:

(1) Training is established, developed, and administered to provide required knowledge and skills to achieve a temporary tower rating as prescribed in this notice.

(2) Training and written/practical examinations are documented on a signed FAA Form 3120-25, ATCT/ARTCC OJT Instruction/Evaluation Report, or its electronic equivalent.

(3) Training documents are prepared and distributed in a timely manner.

(4) Training documents are retained in accordance with this chapter.

(5) Event-specific procedures are developed.

b. Other Special Event Temporary Control Tower operational personnel must:

(1) Hold a current FAA ATCT credential or Control Tower Operator Certificate.

(2) Receive ILT and/or self-study on event-specific procedures and related training materials in support of Special Event Temporary Control Towers.

3. Special Events/Temporary Control Tower Specialist Training Requirements.

a. Qualification Training Requirements:

(1) Because operational circumstances vary across event locations, for those Special Event Temporary Control Tower facilities staffed by agency personnel, the Air Traffic Manager and the NATCA Representative at the Special Event Temporary Control Tower must collaborate to determine the appropriate qualification training hours and the content for each event. Adequate duty time must be provided for completion of these requirements.

05/24/2018 JO 3120.4P CHG 1

(2) All operational personnel at Special Event Temporary Control Towers must attain an 80% passing grade of a written/practical examination that includes subjects in paragraph 2 of this section applicable to the event prior to performing safety-related air traffic control duties.

c. Event-Specific Training may include:

(1) Operational

(a) Best operating practices

(b) Available weather information, equipment, and capabilities (e.g., Automated Surface Observing System Augmentation)

(c) Status information area (SIA)

(d) Strip marking/pad management

(e) Reporting points

(f) Position description/duties

(g) Opposite Direction Operations (ODO)

(h) Waivered Procedures

(i) Frequencies

(j) Type/Mix of Traffic

(2) Notices to Airmen (NOTAMs)

(a) Tower hours of operation

(b) Temporary Flight Restriction (TFR)

(c) Aerobatic Demonstration Area

(d) Letters to Airmen (LTA)

(e) Special Flight Procedures

(3) Letters of Agreement (LOAs)

(a) Movement/non-movement areas

(b) Emergency procedures

(c) Adjacent/overlying air traffic facilities

05/24/2018 JO 3120.4P CHG 1

(4) Airport Layout/Diagram

(a) Aircraft parking and ground movement

(b) Airport elevation

(c) Runway numbers, lengths, and widths

(d) Surface composition (e.g., other than hard surface)

(e) Distance remaining from intersections

(f) Helipad or other landing surface areas

(g) Taxiway widths and restrictions

(h) Airport tenant/building locations

(i) Critical areas

(j) Airspace Requirements

(k) Hot Spots

(5) Equipment

(a) Radios

(b) Light guns

(c) Internal FM

(d) Automatic Terminal Information Service (ATIS)

(e) Airport lighting

(f) Approach lighting

(6) Emergency Procedures/Contingency Plan

(a) Flight Standards contact information

(b) Incident/accident documentation/reporting procedures

(7) Special Procedures

(a) Drones and Unmanned Aircraft Systems

(b) Ride hopper (i.e., rides for hire)

05/24/2018 JO 3120.4P CHG 1

(c) Reporting No Radio (NORDO) procedures

(8) Technical Operations Support

(a) Contact information

4. Special Event/Temporary Control Tower Documentation and Record… › b. Retention.

(b) Onsite or offsite available support

(9) Performance Expectations

(10) Airport Security

4. Special Event/Temporary Control Tower Documentation and Record Retention.

a. Documentation. Document the following on the FAA Form 3120-25:

(1) ILT/Self Study

(2) Written examinations

(3) Practical examinations

(4) Populate Block 12, Comments, with the following statement:

(a) Applicable written/practical examinations have been administered and completed successfully.

b. Retention. The certifying facility for the Special Event Temporary Control Tower will retain all training documentation in accordance with national directives, including:

(1) Facility rating and all supporting documentation

(2) Training manual and all related training material

Appendix A. › 1. General.

Appendix A

Appendix A. Instructions: Training and Proficiency Record (FAA Form 3120-1)

1. General. This appendix conveys instructions for recording employment data, training, and certification entries on FAA Form 3120-1. Examples of corresponding TRAX records are shown. TRAX, or eLMS if applicable, maintains all data logged on FAA Form 3120-1.

a. ATM or designee must ensure that training record entries conform to the requirements of this appendix. These requirements apply to all training occurring on or after the effective date of this order. The requirements described herein are not retroactive.

Note: Names entered on the orange cover portion are not required to conform to official payroll name.

b. Training, certifications, recertifications, and technical performance appraisals must be recorded in this record. Other data, such as temporary details, currency maintenance, awards, disciplinary actions, collateral duties, participation on committees, copies of training and other certificates, etc., should be maintained in working-level personnel records. Air Traffic Safety Oversight Service (AOV) credentialing actions are not required to be recorded on Form 3120-1. These records are maintained in the AOV Credentialing Program database.

c. When completing FAA Form 3120-1, enter only the required specific data. Training record entries must be complete and accurate. Entries must be typed or written in blue or black ink. If an entry must be changed, the incorrect entry must be lined out and the correct information must be inserted. Affected employees and the person making the change must initial the new entry. Computer TRAX records must be updated when certified TRAX records are changed.

d. All entries, including the employee’s initials and certification signature, must be recorded on FAA Form 3120-1 or the TRAX program no later than 120 calendar days following the month in which the training was completed. By initialing or signing, the employee acknowledges that the training recorded has been provided. Operating initials must be used. Certified TRAX records must be retained in section IX of the employee’s FAA Form 3120-1.

e. Entries on FAA Form 3120-1 that reflect position certification/recertification and performance reviews must be signed by the employee’s first-level manager, even though this individual may not have performed the position certification/recertification or appraisal. This signature indicates that the entry (information) logged on FAA Form 3120-1 is accurate.

f. The certification signature for any instructor-led training conducted, including briefings, indicates that the entry is correct. Therefore, the certification signature for instructor-led training entries may be that of the facility’s support specialist or an FLM/STMC who has knowledge that the training was conducted.

g. Manual entries must be single spaced. Blocks on the entry line for which no entry will be made must have a diagonal line drawn through them. Portions of a page not intended for future use must also have a diagonal line drawn through them.

Appendix A h. A signature stamp may be used by the certifying official or FLM/STMC as an aid to reduce workload. A signature stamp must only be used by the person whose signature is on the stamp.

i. Each training entry must have a separate signature and set of initials, except as noted in section V and TRAX.

j. Mandatory briefing items not pertaining to qualification, certification, proficiency, or management training (e.g., Standards of Conduct, Drug Awareness, The Performance Management System, etc.), must not be recorded on Form 3120-1.

Appendix A 2. Section I. Employment Data. The entries in this section pertain to specific employment information.

Appendix A. › 3. Section II A. Air Traffic Certificates.

Block A. EMPLOYEE’S NAME: Enter the employee’s full payroll name. In the event of a legal name change because of marriage or other reasons, put a single line through the old name and insert the new name and the date of the entry in this block. Do not obliterate the old name since it may be necessary to refer to this name at a later time. The employee must initial next to the name change. The person making the change must initial the new entry.

Block B. DATE EOD WITH FAA: Enter the date the employee entered on duty (EOD) with the FAA. Do not use the employee’s service computation date. The entry in this block is made only at the employee’s first facility of assignment.

Block C. FACILITY: Enter the facility’s three-character identifier, type, and level.

Block D. EOD: Enter the date the employee was officially assigned to the facility. Use the effective date shown on the official Notification of Personnel Action.

Block E. EMPL INIT: The employee must initial in this block.

Note: If the level of a facility changes while an employee is at the facility, make a new entry. Enter the date of the facility-level change in the EOD column.

Figure A-1: Section I, Employment Data

A Erica S. Smith Mapp 2/14/15

DATE EOD WITH FA 1/2/00

C

FACILITY

D

EOD

E

EMPL INIT

C

FACILITY

D

EOD

E

EMPL INIT

FAI FSS 4/2/00

APA ATCT ATC-6 5/1/05

OKC ATCT ATC-9 1/9/07

ZAU ARTCC ATC-12 1/20/09

3. Section II A. Air Traffic Certificates. This section relates to certificates that are required for the performance of AT duties and that are not specific to a particular location or area of operation. Do not enter pilot or flight inspection certificate information, etc. Data in this section should not be confused with ratings, which are described in section II B.

Block A. CERTIFICATE TITLE: Enter the title of the certificate.

Block B. CERTIFICATE NUMBER: Enter the certificate number. If no number is associated with the certificate, enter “N/A.”

4. Section II B. Air Traffic Ratings. › Figure A-3: Section II B, Air Traffic Ratings

EMPL.

Appendix A Block C. DATE ISSUED: Enter the date of issuance as shown on the certificate. If no date is shown on the certificate, enter the date of the entry.

Block D. EMPL INIT: The employee must initial in this block.

Figure A-2: Section II A, Air Traffic Certificates

CERTIFICATE TITLE CERTIFICATE DATE EMPL.

Control Tower Operator 457924411 4/15/00

Pilot Weather Briefing Certificate 68359 10/15/00

TWR Visibility Certificate 1234 10/19/02

Air Traffic Control Specialist N/A 11/16/03

4. Section II B. Air Traffic Ratings. The entries in this section relate to specific facility ratings, not to certificates. Ratings describe facility operational functions and are required for employees to perform the full range of duties associated with a particular area of specialization or facility. The use of the term “Facility” or “Area” indicates that the employee has successfully completed all the certification requirements for that facility or area.

Block A. RATING: Enter the title of the rating.

Block B. FACILITY: Enter the facility’s three-character identifier, level, and type.

Block C. DATE ISSUED: Enter the effective date of the rating.

Block D. EMPL INIT: The employee must initial in this block.

Figure A-3: Section II B, Air Traffic Ratings

RATING FACILITY DATE EMPL

Facility FAI FSS 10/4/00

Facility APA ATCT 3/3/04

Gateway Area ZKC ARTCC 3/12/06

Facility R90 TRACON 2/9/10

Appendix A. › 5. Section III. Qualification Training.

Appendix A 5. Section III. Qualification Training. Initial qualification training requirements are described in appendices D through F. Training relative to position qualification, including additional OJT hours and position recertification, must be recorded in this section.

Block A. DEVELOPMENT STAGE: Enter the course number. (Course title may be included). For En Route and Terminal field training, indicate whether the training was instructorled, simulated, OJT, and/or additional OJT. Facilities must indicate the position on which qualification has taken place if multiple positions are involved. For recertification, enter recertification and the positions involved.

Block B. FAC IDENT: Enter “AAC” if FAA Academy-conducted. Enter the three-character facility identifier if facility-conducted.

Block C. DATE STARTED: Enter the date the employee began training in this course.

Block D. NO OF AUTH HOURS: Enter the number of hours authorized to complete this course or the number of additional OJT hours authorized. The number of hours entered must not exceed those indicated in the appropriate directive. The hours allowed must be derived from the facility training directive. No entry is required in Block D for FAA Academy-conducted training.

Block E. EMPL INIT: The employee must initial in these blocks.

Block F. DATE COMPLETED: Enter the date the employee successfully completed, received an incomplete in, failed this training course, or was granted additional OJT hours. (If the employee did not successfully complete the training, enter “I” for incomplete or “F” for failed in Block A.)

Block G. HOURS: Enter the actual number of hours the employee used in this portion of the training program. No entry is required in Block G for FAA Academy-conducted training.

Block H. EMPL INIT: The employee must initial in these blocks.

Block I. CERTIFICATION SIGNATURE: The certifying official must sign or use a signature stamp in this block.

5. Section III. Qualification Training. › Figure A-4: Section III (Terminal Example)

Appendix A

Figure A-4: Section III (Terminal Example)

QUALIFICATION TRAINING

A

DEVELOPMENT STAGE

B

FAC IDENT

C

DATE STARTED

D

NO. OF AUTH HOURS

E

EMPL INIT

F

DATE COMPLETED

G

HOURS

H

EMPL INIT

I

CERTIFICATION SIGNATURE

50032 AAC 1/2/00 4/25/00

50034 AAC 11/30/00 12/17/00

55060 FD-TWR Instructor led

PHL 5/1/00 16 5/4/00 16

55060 FD-TWR OJT

PHL 5/8/00 20 5/15/00 18

55060 FD- Radar Instructor led

PHL 5/20/00 20 5/27/00 20

55060 Arrival Data OJT

PHL 6/1/00 30 6/11/00 28

55060 Dept. Data OJT

PHL 6/20/00 40 7/8/00 36

55061 CD Instructor led

PHL 7/20/00 5 7/21/00 5

55061 CD OJT PHL 7/24/00 20 7/30/00 18

55062 GC Instructor led

PHL 8/15/00 40 8/20/00 40

55062 GC OJT PHL 8/23/00 60 9/20/00 54

55063 LC Instructor led

PHL 9/25/00 40 9/30/00 40

FAA Form 3120-1.3 (5-98) NSN: 0052-00-863-7001

Appendix A

Figure A-4: Section III (Terminal Example, continued)

QUALIFICATION TRAINING A

DEVELOPMENT

STAGE

B

FAC

IDENT

C

DATE

STARTED

D

NO. OF

AUTH

HOURS

E

EMPL

INIT

F

DATE

COMPLETED

G

HOURS

H

EMPL

INIT

I

CERTIFICATION

SIGNATURE

55063 LC OJT PHL 10/10/00 100 11/19/00 70

55064 Non-radar Instructor led/Lab

PHL 12/22/00 40 1/4/01 40

55065 Radar Instructor led

PHL 1/10/01 80 1/24/01 80

55065 North Dept. OJT

PHL 1/27/01 90 3/28/01 90

55065 North Dept Addl. OJT

PHL 4/1/01 18 4/6/01 15

55065 South Dept. OJT

PHL 4/10/01 60 5/18/01 55

55065 West Arrival OJT

PHL 5/20/01 80 7/25/01 70

55065 East Arrival OJT

PHL 5/20/01 80 8/1/01 65

55065 Final Approach. OJT

PHL 7/15/01 50 8/27/01 45

Recertification – Tower Positions

9/10/01

OJT Instructor PHL 4/20/02

55073 CIC PHL 3/20/03 40 3/29/03 40

FAA Form 3120-1.3 (5-98) NSN: 0052-00-863-7001

5. Section III. Qualification Training. › Figure A-5: Section III (En Route Example)

Appendix A

Figure A-5: Section III (En Route Example)

QUALIFICATION TRAINING

A

DEVELOPMENT STAGE

B

FAC IDENT

C

DATE STARTED

D

NO. OF AUTH HOURS

E

EMPL INIT

F

DATE COMPLETED

G

HOURS

H

EMPL INIT

I

CERTIFICATION SIGNATURE

50132 AAC 1/2/98 4/4/98

55053 Instructor led

ZDV 4/22/98 48 5/1/98 48

55053 OJT ZDV 5/1/98 80 6/25/98 18.7

55054 Instructor led

ZDV 7/9/98 240 8/25/98 240

55054 LAB ZDV 8/28/98 120 11/30/98 120

55054 OJT RAP HIGH

ZDV 12/9/98 120 2/25/99 94

55054 OJT BFF HIGH

ZDV 4/10/99 80 5/25/99 65

55054 OJT RAP LOW

ZDV 7/9/99 80 8/15/99 56.5

FAA Form 3120-1.3 (5-98) NSN: 0052-00-863-7001

Appendix A

Figure A-5: Section III (En Route Example, continued)

QUALIFICATION TRAINING

A

DEVELOPMENT STAGE

B

FAC IDENT

C

DATE STARTED

D

NO. OF AUTH HOURS

E

EMPL INIT

F

DATE COMPLETED

G

HOURS

H

EMPL INIT

I

CERTIFICATION SIGNATURE

55055 Instructor led

ZDV 11/23/99 60 12/23/99 60

55055 LAB ZDV 1/8/00 160 3/20/00 160

55055 OJT RAP LOW

ZDV 12/1/00 80 2/12/01 80

55055 Add. Hrs OJT RAP LOW

ZDV 2/15/01 16 2/22/01 12

OJT Inst. East Area

ZDV 6/6/02

55055 LAB ZDV 11/1/03 8 11/5/03 8

55055 OJT ZDV 11/11/03 80 12/11/03 80

Recertification ­ East Area

2/15/03

FAA Form 3120-1.3 (5-98) NSN: 0052-00-863-7001

Appendix A

Figure A-6: Section III (FS Example)

QUALIFICATION TRAINING

A

DEVELOPMENT STAGE

B

FAC IDENT

C

DATE STARTED

D

NO. OF AUTH HOURS

E

EMPL INIT

F

DATE COMPLETED

5. Section III. Qualification Training. › Figure A-6: Section III (FS Example)

G

HOURS

H

EMPL INIT

I

CERTIFICATION SIGNATURE

55239 ENA 7/9/99 80 7/21/99 52

55242 ENA 9/12/99 160 9/24/99 70

55241 ENA 10/14/99 100 1/5/00 100

55241 Addl. Hrs. OJT ENA 1/8/00 20 1/15/00 15

OJT Inst. Flight Data ENA 9/12/00

55247 ENA 3/10/01 60 4/10/02 60

FAA Form 3120-1.3 (5-98) NSN: 0052-00-863-7001

Appendix A. › 7. Section V.

Appendix A 6. Section IV. Equipment Certification.

a. Only equipment training that specifically requires a certification examination must be entered in this section. The only equipment training that meets this requirement is the Terminal Radar Qualification Examination.

Note: The En Route Radar Qualification Examination must not be logged in this section.

b. Other equipment training that is associated with position certification, such as communications, lighting systems, recording, and other ATC equipment, must not be logged in this section. Such equipment training is considered part of the qualification process, and no need exists to separately record certification thereon. Refer to the appropriate instructional program guide for equipment certification requirements. If equipment training is provided as a result of facilities receiving new equipment (other than that requiring a certification examination), include as supplemental training in section V.

Block A. DATE: Enter the date of the equipment certification indicated on the appropriate certificate examination.

Block B. EQUIPMENT: Specify the type of equipment.

Block C. FAC IDENT: Enter the three-character facility identifier.

Block D. CERTIFICATION SIGNATURE: The certifying official must sign or use a signature stamp in this block.

Block E. EMPL INIT: The employee must initial in this block.

Figure A-7: Section IV, Equipment Certification

A

DATE

B

EQUIPMENT

C

FAC

IDENT

D

CERTIFICATION

SIGNATURE

E

EMPL

INIT

9/15/98 Radar Qualification Exam DFW

James Matthews JM

7. Section V. Proficiency (Recurrent, Refresher, Supplemental, Skill Enhancement), and Remedial Training. Entries in this section must specifically describe the training provided and may be disposed of 5 years after the training occurs. Refer to chapter 4, paragraph 5, Proficiency Training, for the type of training to be entered in this section. Air Traffic Safety Action Program (ATSAP) training must be recorded in this section with ATSAP as the major subject area and the type coded as 4.

a. ATM or designee is authorized to use coded entries in this section if a corresponding facility master sheet is maintained that specifically describes the training provided. This master sheet must be attached to the employee’s training record and forwarded to the receiving facility

Appendix A in the event the employee is transferred.

Note: A photocopy or other reproduction of FAA Form 3120-1.5, Proficiency Training, may be used in lieu of individual entries in each employee’s FAA Form 3120-1. When a reproduction is used, the following statement must be on the form where the employee’s signature is to be placed: “I certify that I have received the above Proficiency Training for

(Month) (Year)

(Specialist’s Signature) (Certification Signature)

b. Scheduled Proficiency Training may be entered in section V of FAA Form 3120-1 prior to the time the training is administered, under the following conditions:

(1) Only Blocks A, B, C, and E may be completed before the training is administered.

(2) Blocks D, F, and G must be completed after the training has been administered and in accordance with other requirements of this order.

(3) The date entered in Block A must reflect the date that information was entered in Blocks B, C, and E.

Block A. DATE: Record the date the training was entered on FAA Form 3120-1. A date stamp may be used.

Block B. MAJOR SUBJECT AREAS: Specifically describe or use a coded entry for refresher or supplemental training. Remedial and SET entries must specifically describe the training conducted. Coded entries must not be used for remedial or SET. If the facility is maintaining a master code/decode sheet, a single entry (e.g., 1/2) may be utilized if both refresher and supplemental training items were provided during a single briefing. If a master code/decode sheet is maintained, training items must be identified by a singular training type. If training is conducted via CBI, enter CBI. Training recorded as part of the ATSAP program must be recorded as ATSAP.

Block C. TYPE: Indicate the type of training by number: 1 = Refresher, 2 = Supplemental, 3 = Remedial, 4 = Skill Enhancement.

Note: SET will be encoded number 4. Continue to use FAA Form 3120-1.5 (dated 4/77) until supplies are exhausted. Make a written annotation explaining code 4 at the bottom of the form when entries appear on that page.

Block D. DATE COMPLETED: Enter the date the training was completed.

7. Section V. › Figure A-8

Appendix A Block E. HOURS: Indicate the number of actual training hours.

Block F. CERTIFICATION SIGNATURE: The certifying official must sign or use a signature stamp in this block.

Block G. EMPL INIT: The employee must initial in this block.

Figure A-8: Section V Proficiency (Recurrent, Refresher, Supplemental, Skill Enhancement), and Remedial Training

A

DATE

B

MAJOR SUBJECT AREAS

C

TYPE 1/

D

DATE COMPLETED

E

HOURS

F

CERTIFICATION SIGNATURE

G

EMPL INIT

1/15/00 Wake Turbulence Film 1 4/10/00 .5

2/1/00 57002, NOTAMs CBI 1 1/22/00 4.0

3/10/00 Aircraft Characteristics Climb Rates Vertical Separation Standards

3 3/3/00 2

5/1/00 Speed Control & Sequencing

4 4/10/00 1.2

6/22/00 Review: Radar Vector Procedures, Effect of Temperature on Climb Rates, Coordination (Facility SOP on Position Relief Briefings)

3 6/15/00 8

6/22/01 ETG Lab Problems 2, 8, 11, 21, 22, 23, 24, 25 3 6/21/01 16

6/30/01 Lost Aircraft Orientation 1 6/30/01 2

7/1/01 Pilot Weather Briefing 1 7/1/01 2

8/3/08 ATSAP 4 7/3/08 .5

8/3/08 VSCS ATCS Operations Course

2 7/27/08 16

1/ TRAINING

TYPE CODE 1 - Refresher 2 - Supplemental Enhancement

3 - Remedial 4 - Skill

FAA Form 3120-1.5 (5-98) NSN: 0052-00-863-8001

Appendix A 8. Section VI. Technical Appraisal. The technical appraisal section for all options must include the OJTI skill check described in chapter 6.

Block A. DATE COMPLETED: Enter the date shown on the appraisal form or the date the skill check was completed.

Appendix A. › 9. Section VII. Management and Other Training.

Block B. TECHNICAL APPRAISAL: Enter the position on which the appraisal took place, the type of appraisal, and the result (satisfactory or unsatisfactory). If the result is unsatisfactory, recertification is required prior to the resumption of operational or OJTI duties.

Block C. DATE DISCUSSED: Enter the date the appraisal was discussed with the employee.

Block D. CERTIFICATION SIGNATURE: For technical appraisals and OJTI skill checks, the employee’s FLM/STMC, even though this individual may not have performed the appraisal, must sign or use a signature stamp in this block.

Block E. EMPL INIT: The employee must initial in this block.

Figure A-9: Section VI, Technical Appraisal

A

DATE COMPLETED

B

TECHNICAL APPRAISAL

C

DATE DISCUSSED

D

CERTIFICATION SIGNATURE

E

EMPL INIT

9/25/00 East Arrival-OJTI Performance Skill Check—Satisfactory 9/25/00

10/1/02 RAP LOW- Performance Skill Check Unsatisfactory 10/1/02

FAA Form 3120-1.6 (5-98) NSN: 0052-00-863-9001

9. Section VII. Management and Other Training. All management and other agencyapproved training not previously listed must be entered in this section. This includes, but is not limited to, automation and other technical training, correspondence, college, out-of-agency, and instructor training courses. Only training that was completed during employment with FAA must be recorded in this section. Management and other training completed via eLMS need not be entered.

Block A. DATE: Enter the date the training was completed.

Block B. COURSE: Enter the course title and the FAA course number, if applicable, as described on the training certificate, transcript, or other official course document. Refer to the FAA Catalog of Training Courses or the CBI course catalog for this information. Regardless of length, all courses assigned an FAA course number or courses specified in FAA directives must

9. Section VII. Management and Other Training. › Figure A-10: Section VII, Management and Other Training

Appendix A be recorded in this section. All other courses of 8 hours or more must be recorded in this section. Courses of less than 8 hours may be recorded in this section if specified in a facility directive.

Block C. LOCATION: Enter the location where the training was conducted (e.g., FAA Academy, university name, facility, regional office, correspondence course, etc.).

Block D. HOURS: Enter the number of hours indicated in the FAA course catalog. If not contained in the catalog, use the hours in the course description document. Exception: For college/university courses, enter the number of quarter or semester credit-hours attained.

Block E. EMPL INIT: The employee must initial in this block.

Figure A-10: Section VII, Management and Other Training

A

DATE COMPLETED

B

COURSE

C

LOCATION

D

HOURS

E

EMPL INIT

5/5/90 ARTS IIIA for Automation Specialists, Phase V 53010 FAA Academy 240

6/12/91 Fundamentals of Supervision 14002 Correspondence Course

150

11/19/91 Aviation-A Global History Princeton University 3 Qtr.

9/8/98 Facility instructor Training 10501 FAA Academy 80

Continue reading ↓ 120 of 494 passages shown