Radar Vectors
FAA Notice Current Issued Sep 19, 2025 AFS-400 69 pages Copy saved Nov 18, 2026

Notice N 8900.752 Part P Operations Specifications (OpSpecs), Management Specifications (MSpecs), and Letters of Authorization (LOA) for Powered-Lift

This notice announces new Part P operations specification (OpSpec)/management specification (MSpec)/Letter of Authorization (LOA) templates for operators conducting Title 14 of the Code of Federal Regulations (14 CFR) part 194 powered-lift operations under 14 CFR parts 91, 91 subpart K (part 91K), and 135.

Official source ↗ Open PDF

5. Action.

Distribution: Electronic Only Initiated By: AFS-400

NOTICE

U.S. DEPARTMENT OF TRANSPORTATION

FEDERAL AVIATION ADMINISTRATION N 8900.752

National Policy

Effective Date: 9/19/25

Cancellation Date: 9/19/26

SUBJ: Part P Operations Specifications (OpSpecs), Management Specifications

(MSpecs), and Letters of Authorization (LOA) for Powered-Lift

1. Purpose of This Notice. This notice announces new Part P operations specification (OpSpec)/management specification (MSpec)/Letter of Authorization (LOA) templates for operators conducting Title 14 of the Code of Federal Regulations (14 CFR) part 194 powered-lift operations under 14 CFR parts 91, 91 subpart K (part 91K), and 135.

2. Audience. The primary audience for this notice is Flight Standards (FS) Safety Assurance principal inspectors (PI) with oversight responsibilities for operators using powered-lift under parts 91, 91K, and 135. The secondary audience includes FS personnel in the Office of Safety Standards.

3. Where You Can Find This Notice. You can find this notice on the MyFAA employee website at https://employees.faa.gov/tools_resources/orders_notices and the Dynamic Regulatory System (DRS) at https://drs.faa.gov. Operators and the public can find this notice on the Federal Aviation Administration’s (FAA) website at https://www.faa.gov/regulations_policies/orders_no tices and DRS.

4. Background. The FAA published part 194 to address regulatory barriers to safely incorporate powered-lift into the National Airspace System (NAS). The final rule enables the FAA to authorize parts 91, 91K, and 135 powered-lift operators to conduct terminal instrument procedures (IP) and specify airport authorizations and limitations. The FAA has assigned OpSpec/MSpec/LOA parts specific to the category of aircraft. Part C is for airplanes, Part H is for helicopters, and Part P is for the new powered-lift category. Guidance for the new Part P templates can be found in FAA Order 8900.1, Volume 3, Chapter 18, Section 9, Part P Operations Specifications—Powered-Lift Instrument Procedures, Airport Authorizations, and Limitations. Appendix A to this notice contains a list of new templates. Appendices B through Y to this notice provide examples of the new OpSpecs templates for a part 135 powered-lift operator.

5. Action. This change affects PIs with responsibility for the issuance, amendment, and oversight of OpSpecs/MSpecs/LOAs for powered-lift operators. PIs will review this notice and Order 8900.1 guidance prior to the issuance of OpSpecs/MSpecs/LOAs for powered-lift operators.

9/19/25 N 8900.752

6. Disposition.

6. Disposition. We have incorporated the information in this notice into Order 8900.1. Direct questions or comments concerning the information in this notice to the Flight Technologies and Procedures Division (AFS-400) at 202-267-8976 or [email protected].

Hugh Thomas for Lawrence Fields Executive Director, Flight Standards Service

Appendix A. List of New and Revised OpSpecs

9/19/25 N 8900.752 Appendix A

Appendix A. List of New and Revised OpSpecs

Table A-1. New OpSpec/MSpec/LOA Paragraphs

Paragraph 14 CFR Part Title

P048 91, 91K, 135, 121/135 Enhanced Flight Vision System (EFVS) Operations

P049 91K, 135, 121/135 Destination Airport Analysis Program

P059 91, 91K, 135, 121/135 Special Authorization Category I (SA CAT I) Instrument Approach and Landing Operations

P071 135, 121/135 Autopilot Minimum Use Altitudes/Heights (MUH)

P073 91, 91K, 135, 121/135 Vertical Navigation (VNAV) Instrument Approach Procedures (IAP) Using Minimum Descent Altitude (MDA) as a Decision Altitude (DA)

P085 135, 121/135 14 CFR Part 97 NDB, NDB/DME, VOR, VOR/DME, and TACAN Instrument Approach Procedures Using Substitute Means of Navigation

P101 91K, 135, 121/135 Terminal Instrument Procedures—Powered-Lift

P102 91K, 135, 121/135 Authorized Straight-In Instrument Approach Procedures

P103 91K, 135, 121/135 Straight-In Category I Approach Minima

P104 91, 91K, 135, 121/135 Powered-Lift Offshore Instrument Operations: Offshore Standard Approach Procedure (OSAP), Airborne Radar Approach (ARA), and Helicopter En Route Descent Area (HEDA) Operations

P105 91K, 135, 121/135 Alternate Airport IFR Weather Minimums

P106 135, 121/135 IFR Takeoff Minimums

P108 91, 91K, 135, 121/135 Category II and Category III Instrument Approach and Landing Operations

P110 91K, 135, 121/135 Automatic Landing Operations Other Than Categories II and III

P112 91K, 135, 121/135 Instrument Approach Operations Using an Area Navigation System

9/19/25 N 8900.752 Appendix A

Paragraph 14 CFR Part Title

P113 91K, 135, 121/135 Terminal Area IFR Operations in Class G Airspace and/or at Airports Without an Operating Control Tower—Nonscheduled Passenger and All-Cargo Operations

P114 91K, 135, 121/135 Powered-Lift Authorizations, Provisions, and Limitations into Certain Airports

P118 91K, 135, 121/135 Circle-to-Land Operations

P119 91K, 135, 121/135 Category I Contact Approach Procedures

P120 135, 121/135 Airports Authorized for Scheduled Operations

P121 135, 121/135 Terminal Area IFR Powered-Lift Operations in Class G Airspace—Scheduled Passenger Operations

P122 91, 91K, 135, 121/135 Special Instrument Procedures

P123 91K, 135, 121/135 IFR Operations for Powered-Lift Utilizing Required Navigation Performance (RNP) 0.3 for En Route and Terminal Operations

P384 91, 91K, 135, 121/135 Required Navigation Performance (RNP) Procedures with Authorization Required (AR)

(2) When authorized in Table 1 above for EFVS operations under §… › (b) When the latest reported visibility is at least RVR 1000 for the…

9/19/25 N 8900.752 Appendix B

Appendix B. Sample OpSpec P048, Enhanced Flight Vision System (EFVS)

Operations: 14 CFR Part 135

a. The certificate holder is authorized to conduct the Enhanced Flight Vision System (EFVS) operations under 14 CFR Part 91, § 91.176 as specified in this operations specification.

b. Authorized Powered-Lift, Equipment, and EFVS Operations. The certificate holder is authorized to conduct the EFVS operations using the aircraft and equipment listed in Table 1 below.

Table 1 – Authorized Powered-Lift, Equipment, and EFVS Operations

Powered-Lift

(M/M/S)

EFVS Equipment EFVS Operation(s) EFVS Operational

Credit

c. Provisions and Limitations.

(1) Minimum Visibility for Use with EFVS. The certificate holder is authorized to reduce the visibility minimums required to takeoff an aircraft under IFR or begin an IFR or over-the-top operation to destination airports, to begin the Final Approach Segment (FAS), or continue an IAP under 14 CFR Part 135.225, 135.219 and Part 194, at an airport in accordance with the EFVS.

(a) Reducing minimums for use with EFVS:

(i) Is not authorized for flight release of an aircraft to destination airports unless personnel assigned to operational control duties have successfully completed the certificate holder’s EFVS training.

(ii) Is not authorized for meeting alternate airport weather requirements for flight release purposes.

(b) Table 2A or 2B below must be used for determining IAP visibility minimums with the use of EFVS.

(2) When authorized in Table 1 above for EFVS operations under § 91.176(a) and if conducting eligible on demand operations, the certificate holder must only conduct those operations at airports:

(a) With a weather reporting facility operated by the U.S. National Weather Service (NWS), a source approved by the U.S. NWS, or a source approved by the Administrator; and

(b) When the latest reported visibility is at least RVR 1000 for the runway of intended landing or, if RVR is not reported, at least ¼ statute mile.

9/19/25 N 8900.752 Appendix B

Table 2A – Determining IAP Visibility Minimums with EFVS (RVR)

Visibility Required

Without the Use

of EFVS

25% Reduction Minimum Visibility with the Use of EFVS

33% Reduction Minimum Visibility with the Use of EFVS

50% Reduction Minimum Visibility with the Use of EFVS

1400 1100 1000 1000

1800 1400 1200 1000

2000 1500 1300 1000

2200 1700 1500 1100

2400 1800 1600 1200

2600 2000 1700 1300

3000 2300 2000 1500

3500 2600 2300 1800

4000 3000 2700 2000

4500 3400 3000 2300

5000 3800 3400 2500

5500 4100 3700 2800

6000 4500 4000 3000

9/19/25 N 8900.752 Appendix B

Table 2B – Determining IAP Visibility Minimums with EFVS (Statute Mile)

Visibility Required

Without the Use

of EFVS

25% Reduction Minimum Visibility with the Use of EFVS

33% Reduction Minimum Visibility with the Use of EFVS

50% Reduction Minimum Visibility with the Use of EFVS

½ ⅜ ¼ ¼

⅝ ½ ⅜ ⅜

¾ ½ ½ ⅜

⅞ ⅝ ½ ½

1 ¾ ⅝ ½

1 ⅛ 1 ¾ ⅝

1 ¼ 1 ¾ ⅝

1 ⅜ 1 1 ¾

1 ½ 1 ⅛ 1 ¾

1 ⅝ 1 ¼ 1 ¾

1 ¾ 1⅜ 1 ⅛ ⅞

1 ⅞ 1 ⅜ 1 ¼ 1

2 1 ½ 1 ⅜ 1

2 ½ 1 ⅞ 1 ½ 1 ¼

3 2 ¼ 2 1 ½

Appendix C. › b. Operations specification A057 must be issued for this authorization.

9/19/25 N 8900.752 Appendix C

Appendix C. Sample OpSpec P049, Destination Airport Analysis Program: 14 CFR

Part 135

a. The eligible on-demand certificate holder is authorized to use the Destination Airport Analysis Program described or referenced in this operations specification in accordance with 14 CFR Part 135, § 135.385(f) and § 194.306(hhh) and (iii).

[Enter procedures used for destination airport analysis program or manual reference.]

[Text Box]

b. Operations specification A057 must be issued for this authorization.

(5) The following, along with any applicable equipment otherwise… › (b) At least one radio altimeter (RA), although two are recommended.

9/19/25 N 8900.752 Appendix D

Appendix D. Sample OpSpec P059, Special Authorization Category I (SA CAT I)

Instrument Approach and Landing Operations: 14 CFR Part 135

a. The certificate holder is authorized to conduct Special Authorization Category I (SA CAT I) instrument approach and landing operations, when in compliance with 14 CFR Part 97 special aircrew and aircraft certification requirements, as specified in this operations specification.

b. The certificate holder is authorized SA CAT I landing minimums as low as a 150 foot decision height (DH) and 1400 Runway Visual Range (RVR) to approved runways without touchdown zone (TDZ) lights and/or runway centerline (RCL) lights in accordance with the following limitations and provisions:

(1) Each aircraft used to conduct SA CAT I operations must be equipped with an operable manual flight guidance system (FGS) certified and maintained to support a DH of 150 feet or lower.

(2) Required equipment approved as basis for SA CAT I authorization (e.g., Head-Up Display (HUD), Synthetic Vision Guidance System (SVGS)) must provide each pilot with course and glide path command guidance to the DH, while simultaneously providing the pilot flying (PF) with a continuous indication of the desired trajectory to the runway TDZ independent of the guidance used for the approach. The guidance system must also provide the PF with dynamic perception of aircraft position relative to the TDZ of the runway of intended landing to facilitate the transition to the visual segment of the approach by reducing the time needed for the acquisition of visual cues.

(3) An aircraft type and/or system previously approved for SA CAT I, based upon HUD equipment, is considered to meet the requirements of this operations specification.

(4) SA CAT I authorization is based upon.

[Select the applicable required approved equipment that is the basis of this SA CAT I authorization. MUST SELECT ONE.]

○ a certified HUD.

○ a certified SVGS displayed on a Head-Down Display (HDD).

○ either a certified HUD or a certified SVGS displayed on a Head-Down Display (HDD).

(5) The following, along with any applicable equipment otherwise required for CAT I IFR operations, must be installed and operating properly to conduct SA CAT I operations.

(a) Two independent navigation receivers, or equivalent, of each type intended for use.

(b) At least one radio altimeter (RA), although two are recommended.

Appendix D. › e. Maintenance. The certificate holder must incorporate the design…

9/19/25 N 8900.752 Appendix D

(c) Rain removal equipment for each pilot (e.g., windshield wiper, bleed air, or rain repellant).

(6) If SVGS is used to conduct SA CAT I operations, the certificate holder must ensure SVGS databases contain current data.

c. Additional Limitations and Provisions. The flightcrew must use the means of guidance authorized in subparagraph b(4) to the DH or to the initiation of missed approach, and the guidance must be continuously displayed on the approved system.

(1) After passing the final approach fix (FAF), a missed approach must be executed if the approach guidance system specified in subparagraph b(4), or any other airborne equipment required for the particular SA CAT I operation being conducted, becomes inoperative or is disengaged, unless the requirements of 14 CFR Part 91, § 91.175(c) can be met.

(2) The crosswind component on the landing runway must be 15 knots or less unless the Aircraft Flight Manual’s (AFM) crosswind limitation is more restrictive.

(3) The instrument approach procedure (IAP) must have published SA CAT I minimums.

(4) TDZ RVR reports for the landing runway are controlling. The mid-RVR report may NOT be substituted for the TDZ RVR report in SA CAT I operations.

(5) Single-pilot operations are not authorized for SA CAT I. The certificate holder must use a two-pilot flightcrew in aircraft appropriately equipped for two-pilot IFR.

d. Pilot Qualifications and Approved Training. The minimums prescribed in this operations specification are authorized for only those pilots in command (PIC) and seconds in command (SIC) who have completed the certificate holder’s SA CAT I training and qualification program approved by the Administrator, and have been qualified by one of the certificate holder’s check pilots or an FAA inspector, in each guidance system to be used for an SA CAT I operation specified in subparagraph b(4). The flightcrew must demonstrate proficiency in instrument approaches and landings to SA CAT I minimums or lower (e.g. CAT II or CAT III) using each FGS authorized for SA CAT I operations.

e. Maintenance. The certificate holder must incorporate the design approval holder’s (DAH) instructions for continued airworthiness (ICA) into its Continuous Airworthiness Maintenance Program (CAMP) or Approved Aircraft Inspection Program (AAIP) for the aircraft used in SA CAT I operations. This requirement includes cleaning, inspection, adjusting, testing and any other actions specified at time of FGS certification to maintain airworthiness.

Appendix E. › e. Required Training. The flightcrew must have successfully completed…

9/19/25 N 8900.752 Appendix E

Appendix E. Sample OpSpec P071, Autopilot Minimum Use Altitudes/Heights

(MUH): 14 CFR Part 135

a. The certificate holder is authorized to use autopilot minimum use altitudes/heights (MUH) in accordance with 14 CFR Part 135, § 135.93 and Part 194, § 194.306(c) and the provisions and limitations of this operations specification.

b. Approved Powered-lift M/M/S and Equipment. The certificate holder is authorized to operate with the approved powered-lift Make/Model/Series (M/M/S) and autopilot systems listed in Table 1 below at the associated MUHs. Powered-lift aircraft with the same M/M/S but equipped with a different autopilot model/version must be listed separately.

c. MUHs. Takeoff/initial climb and go-around/missed approach altitudes/heights are minimum engagement altitudes/heights. Enroute and Approach MUHs are autopilot disengage altitudes/heights. These altitudes/heights must be listed in Table 1 for each individual phase of flight. The altitudes/heights listed in Table 1 are above airport elevation, terrain, or touchdown zone elevation (TDZE) unless associated with a DA/H or MDA. If a height is not specified in the Aircraft Flight Manual (AFM), AFM Supplement or specified and approved by AFS-400 in coordination with the FSB, a minimum altitude/height will be indicated in Table 1. These are: Takeoff/Initial Climb; 500 ft., Enroute; 500 ft., and Approach; MDA/DA/H minus 50 ft. An altitude/height determined by the Administrator will be annotated with the acronym FAA next to the number (e.g., 150 ft. (FAA)).

Table 1 – Approved Powered-Lift, Equipment and MUHs

Powered-lift

M/M/S

Autopilot Manufacturer

Autopilot Model/Version

Minimum Use Altitudes/Heights (feet)

Takeoff/Initial Climb Enroute Approach

d. Provisions and Limitations.

(1) Operations specification P071 does not replace or override operations specifications P108 Category II and Category III Instrument Approach and Landing Operations or P110 Automatic Landing Operations Other Than Categories II and III.

(2) Operations. The certificate holder must not engage the autopilot unless the autopilot system is fully operational. The certificate holder must conduct operations in accordance with the airworthiness certification of the autopilot system.

(3) Airworthiness. The certificate holder must maintain the powered-lift M/M/S and equipment listed in Table 1.

e. Required Training. The flightcrew must have successfully completed the certificate holder’s approved training program curriculum on the equipment and instrument approach procedures (IAP) to be used.

(1) Serves a runway that has a published RNAV IAP (“RNAV (GPS),” “RNAV… › (d) Has a published VDA coincident with or higher than the barometric…

9/19/25 N 8900.752 Appendix F

Appendix F. Sample OpSpec P073, Vertical Navigation (VNAV) Instrument Approach Procedures (IAP) Using Minimum Descent Altitude (MDA) as a Decision

Altitude (DA): 14 CFR Part 135

a. The certificate holder is authorized to use a minimum descent altitude (MDA) as a decision altitude (height) (DA(H)) when using vertical navigation (VNAV) as advisory information on a Nonprecision Approach (NPA). The certificate holder will use operations specification P073 in conjunction with operations specification P103, Straight-in Category I Approach Minima. The certificate holder is authorized to conduct instrument approach operations using the following powered-lift aircraft and Area Navigation (RNAV) systems approved for these VNAV operations as listed in Table 1 below.

Table 1 – Authorized Powered-Lift and Equipment

Powered-Lift Type (M/M/S) Area Navigation System

(Model/Version) Remarks

b. This operations specification provides protection for the temporary altitude loss below the MDA when performing a missed approach at an MDA when used as a DA(H). The use of an MDA as a DA(H) does not ensure obstacle clearance when continuing the approach from the MDA to the landing runway. The certificate holder must see and avoid obstacles between the MDA and the runway when 14 CFR Part 91, § 91.175 and Part 194, § 194.302 requirements are met and the approach is continued below the MDA for landing.

Note: A vertical descent angle (VDA) is advisory. Flying the published VDA below the MDA does not guarantee obstacle clearance.

c. Authorized Approaches. The certificate holder may fly all 14 CFR Part 97 nonprecision straight-in instrument approach procedures (IAP) listed in their operations specification P102, Table 1, Authorized Instrument Approach Procedures, columns 1 and 2 using an MDA as a DA(H) if the approach being flown meets the requirements of subparagraph (1) or (2) below:

(1) Serves a runway that has a published RNAV IAP (“RNAV (GPS),” “RNAV (RNP),” or “GPS” in the title) with a published lateral navigation (LNAV)/VNAV or Required Navigation Performance (RNP) DA(H), and:

(a) Is selected from an approved and current database.

(b) Has the exact published final approach course as the RNAV IAP.

(c) The MDA is equal to or higher than the LNAV/VNAV or RNP DA(H).

(d) Has a published VDA coincident with or higher than the barometric vertical guidance (glideslope (GS)) on the published RNAV IAP. A published VDA is not required when using the LNAV minima line on an RNAV IAP that also has a published lateral approach procedures with vertical guidance (LPV) and/or LNAV/VNAV DA(H).

(1) When operating into an airfield with a 14 CFR Part 139 Visual Glide… › (b) The published final approach course must be within plus or minus 4…

9/19/25 N 8900.752 Appendix F

(2) Serves a runway that has a published instrument landing system (ILS), Global Positioning System (GPS) landing system (GLS), or RNAV IAP with LPV minima, and:

(a) Is selected from an approved and current database.

(b) Has the exact published final approach course as the ILS, GLS, or RNAV IAP.

(c) The MDA is equal to or higher than the ILS, GLS, or LPV DA(H).

(d) Has a published VDA coincident with or higher than the electronic GS on the published ILS, GLS, or RNAV IAP.

(i) A published VDA is not required on an ILS/Localizer (LOC) approach when the ILS GS is out of service and the approach is flown using LOC-only procedures.

(ii) A published VDA is not required when using the LNAV minima line on an RNAV IAP that also has a published LPV and/or LNAV/VNAV DA(H).

d. VNAV Path Angle Limits. The VNAV path angle must be in the range depicted in Table 2 below.

Table 2 – VNAV Path Angle Limits

Condition VNAV Path Angle Limits

Operating in Wing-borne Flight Mode, or Vertical-lift Flight Mode and AFM contains a

limitation against using copter procedures

2.75 – 3.77 degrees for Cat A, B, C, D 2.75 – 3.5 degrees for Cat E

Operating in Vertical-lift Flight Mode and AFM does not contain a limitation against using copter

procedures

2.75 – 5.7 degrees

e. Provisions and Limitations.

(1) When operating into an airfield with a 14 CFR Part 139 Visual Glide Slope Indicator (VGSI), the following requirements must be met:

(a) The VDA or GS on the published final approach course must be coincident with or higher than the published VGSI descent angle.

(b) The published final approach course must be within plus or minus 4 degrees of the runway centerline (RCL).

Note: The certificate holder must refer to the FAA Chart Supplement to verify that there are no VGSI restrictions if the final approach course is offset from the extended RCL.

Appendix F. › f. Required Training. Flightcrews must be trained in accordance with…

9/19/25 N 8900.752 Appendix F

(2) The certificate holder may use baro-VNAV as advisory information to an MDA when the airfield temperature is outside of the RNAV (GPS) or RNAV (RNP) IAP temperature range limitation if the following requirements are met.

(a) Do not use the MDA as a DA(H).

(b) The MDA must be equal to or higher than the DA(H).

(c) The MDA and DA(H) must have the same published final approach course.

(3) The VNAV path must cross at or above all stepdown fix altitudes. The stepdown fix crossing altitudes must be referenced on the barometric altimeter.

(4) The certificate holder may use a continuous descent final approach (CDFA) to an MDA not being used as a DA(H), but will begin the missed approach at an altitude above the MDA that will not allow the aircraft to descend below the MDA.

f. Required Training. Flightcrews must be trained in accordance with the certificate holder’s approved training program to include VNAV procedures and the IAPs listed in operations specification P102 before conducting operations authorized by this paragraph.

(2) IAPs must be selected by procedure name (e.g., line-selectable)… › (b) Heading-based legs associated with procedures may be flown using…

9/19/25 N 8900.752 Appendix G

Appendix G. Sample OpSpec P085, 14 CFR Part 97 NDB, NDB/DME, VOR, VOR/DME, and TACAN Instrument Approach Procedures Using Substitute Means

of Navigation: 14 CFR Part 135

a. The certificate holder is authorized to conduct 14 CFR Part 97 non-directional radio beacon (NDB), NDB/distance measuring equipment (DME), very high frequency omni-directional range station (VOR), VOR/DME, and Tactical Air Navigation System (TACAN) instrument approach procedures (IAP) using Area Navigation (RNAV) equipment with Global Positioning System (GPS) or a Wide Area Augmentation System (WAAS) as an active sensor.

b. Powered-Lift and Equipment Authorization. The certificate holder is authorized to conduct Part 97 NDB, NDB/DME, VOR, VOR/DME, and TACAN IAPs using the following powered-lift Make/Model/Series (M/M/S) and equipment listed in Table 1 below when operated in accordance with the approved Aircraft Flight Manual (AFM), or other approved FAA documents, and this operations specification.

Table 1 – Powered-Lift and Equipment Authorization

Powered-lift M/M/S

RNAV System(s) and Software

Limitations and Provisions Manufacturer Model Software Part/Version

c. Limitations and Provisions.

(1) The certificate holder is authorized to conduct NDB, NDB/DME, VOR, VOR/DME, and TACAN IAPs using the procedures described herein. This operations specification applies when the underlying Navigational Aid (NAVAID) (NDB, VOR, DME, or TACAN) is out of service and/or compatible powered-lift avionics are either not installed (automatic direction finder (ADF), DME, or TACAN) or not operational (VOR, ADF, DME, or TACAN). The certificate holder may need to coordinate with air traffic control (ATC) to receive clearance for a procedure when planning to use an RNAV system as a substitute means of navigation in lieu of an out-of-service NAVAID.

(2) IAPs must be selected by procedure name (e.g., line-selectable) from a current aircraft navigational database and conform to the charted procedure. The certificate holder is responsible for ensuring that the procedure as flown complies with the charted procedure. Department of Defense (DOD) IAPs are considered equivalent to Part 97 unless identified as “Not for Civil Use.”

(a) The navigational database must be obtained from an FAA-approved database supplier.

(b) Heading-based legs associated with procedures may be flown using manual technique (based on indicated magnetic heading) or, if available, extracted from the aircraft database.

c. Limitations and Provisions. › (8) Flightcrews must ensure that the required navigation system…

9/19/25 N 8900.752 Appendix G

(c) If the Aeronautical Information Regulation and Control (AIRAC) cycle will change during flight, the certificate holder must establish flightcrew procedures to ensure the accuracy of navigation data, to include suitability of navigation facilities used to define the procedures for flight. This can be accomplished by verifying electronic data in the expired database with current paper or electronic charts, as applicable. New and old paper/electronic aeronautical charts must be used to verify navigation fixes prior to dispatch. If an amended chart affecting navigation data is published for the procedure, the database must not be used to conduct the procedure.

(3) The certificate holder must ensure one of the following navigation data and flyability validation processes is used and satisfactorily completed prior to conducting operations covered by this operations specification:

(a) Ongoing, system-wide checks of navigation data and flyability.

(b) As needed, procedure-specific checks of navigation data and flyability.

(4) These processes must ensure navigation data (e.g., waypoint names, waypoint sequence, distance between waypoints, heading/course/track information, and vertical path angles) used in airborne equipment conform to published information. The following methods to check the flyability of procedure(s) are acceptable: suitable desktop analysis, simulator evaluation, or flight (in visual meteorological conditions (VMC)) that is compatible with all powered-lift and equipment listed in subparagraph b of this operations specification. If a procedure has previously been flown using compatible powered-lift M/M/S and equipment listed in subparagraph b of this operations specification and found satisfactory while monitoring raw data from the underlying NAVAID, the certificate holder is not required to complete additional flyability checks, provided the lateral path of the procedure has not been modified.

(5) Modification of approach waypoints is prohibited. Waypoints not overflown in compliance with an ATC clearance (e.g., direct-to clearance) may be deleted. This prohibition does not apply to altitude or speed changes that may be required to comply with an ATC clearance.

(6) The certificate holder must develop procedures to verify correct GPS operation if operating powered-lift that do not automatically alert the flightcrew to a loss of the GPS signal.

(7) Operation on NDB, NDB/DME, VOR, VOR/DME, and TACAN IAPs authorized under this operations specification requires a navigation system accuracy less than or equal to 1.0 nautical miles (NM) for initial and intermediate approach segments, 0.3 NM for Final Approach Segments (FAS), and 1.0 NM for Missed Approach Segments (MAS). These operations are not categorized as Required Navigation Performance (RNP) approaches, and do not constitute or require an RNP authorization.

(8) Flightcrews must ensure that the required navigation system accuracy for each flight segment is satisfied. The onboard navigation system performance monitoring and alerting functions of RNP equipment may be used to satisfy this requirement, provided this equipment is found suitable for these purposes. The certificate holder may use the manual setting of minimum RNP (e.g., 0.3 NM) prior to conducting an approach as a method to satisfy the requirements of subparagraphs c(6) and (7).

c. Limitations and Provisions. › (13) The certificate holder must not conduct any operation authorized…

9/19/25 N 8900.752 Appendix G

(9) Flightcrews are expected to maintain procedure centerlines (CL), as depicted by onboard lateral deviation indicators, displays, and/or flight guidance, during all operations described in this operations specification unless otherwise authorized to deviate by ATC or in the instance of an emergency condition. For normal operations, cross-track (XTK) error/deviation (the difference between the RNAV equipment computed path and the powered-lift position relative to the path) should be limited to +/- one-half of the navigation accuracy associated with the procedure segment (i.e., 0.5 NM for the initial and intermediate segments, 0.15 NM for the FAS, and 0.5 NM for the MAS). Brief deviations from this standard (e.g., overshoots or undershoots) during and immediately after turns, up to a maximum of one times the navigation accuracy (i.e., 1.0 NM for the initial and intermediate segments), are allowable.

(10) Flightcrews must execute a missed approach if the allowable navigation system accuracy and/or lateral XTK error is exceeded and unable to remain in VMC while proceeding to the runway using the visual references specified in 14 CFR Part 91, § 91.175 and Part 194, § 194.302 or Part 135, § 135.225 and Part 194, § 194.306, as applicable.

(11) The certificate holder may use RNAV substitution for planning purposes at an alternate airport for Part 97 NDB, NDB/DME, VOR, VOR/DME, and TACAN IAPs. This includes the authorization to use airports with an unmonitored NAVAID as an alternate. This authorization allows the unmonitored NAVAID to be treated as out of service within the context of this authorization only. The certificate holder must be authorized operations specification P105, Alternate Airport IFR Weather Minimums. When using this operations specifications and P105 Alternate Airport IFR Weather Minimums together for alternate planning purposes, the substituted approach must be considered a GPS-based IAP. The certificate holder must follow all P105 limitations and provisions regarding the use of GPS-based IAPs for alternate planning.

(12) The certificate holder must perform a receiver autonomous integrity monitoring (RAIM) availability prediction during flight planning. RAIM must be predicted to be available during periods of operation. The certificate holder must check WAAS Notices to Airmen (NOTAM) when using RNAV equipment with WAAS as an input.

(13) The certificate holder must not conduct any operation authorized by this operations specification unless each pilot satisfactorily completes the certificate holder’s approved training and qualification program for the equipment and any special procedures to be used.

b. If Applicable, Special Limitations and Provisions for Instrument… › (3) When the minima are specified only in meters, the certificate…

9/19/25 N 8900.752 Appendix H

Appendix H. Sample OpSpec P101, Terminal Instrument Procedures—

Powered-Lift: 14 CFR Part 135

a. The certificate holder is authorized to conduct powered-lift terminal instrument operations using the procedures and minimums specified in these operations specifications, provided one of the following conditions is met:

(1) The terminal instrument procedure used is prescribed by these operations specifications.

(2) The terminal instrument procedure used is prescribed by 14 CFR Part 97, Standard Instrument Approach Procedures.

(3) At U.S. military airports, the terminal instrument procedure used is prescribed by the U.S. military agency operating the airport.

(4) If authorized foreign airports, the terminal instrument procedure used at the foreign airport is prescribed or approved by the government of an ICAO contracting state. The terminal instrument procedure must meet criteria equivalent to that specified in either the United States Standard for Terminal Instrument Procedures (TERPS) or ICAO Document 8168-OPS, Procedures for Air Navigation Services-Aircraft Operations (PANS-OPS), Volume II.

b. If Applicable, Special Limitations and Provisions for Instrument Approaches at Foreign Airports.

(1) Terminal instrument procedures may be developed and used by the certificate holder for any foreign airport, provided the certificate holder determines that each procedure developed is equivalent to U.S. TERPS, ICAO PANS-OPS, MIPS criteria, or other special criteria approved by the headquarters Flight Technologies and Procedures Division (AFS-400). The visibility, RVR, or CMV is based on TERPS, EU-OPS 1 or ICAO Document 9365. The certificate holder must submit to the FAA a copy of the terminal instrument procedure with supporting documentation.

(2) At foreign airports, the certificate holder must not conduct terminal instrument procedures determined by the FAA to be “not authorized for United States air carrier use.” In these cases, the certificate holder may develop and use a terminal instrument procedure provided the certificate holder determines that each procedure developed is equivalent to U.S. TERPS, ICAO PANS-OPS, MIPS criteria, or other special criteria approved by the headquarters Flight Technologies and Procedures Division (AFS-400). The visibility, RVR, or CMV is based on TERPS, EU-OPS 1 or ICAO Document 9365. The certificate holder must submit to the FAA a copy of the terminal instrument procedure with supporting documentation.

(3) When the minima are specified only in meters, the certificate holder must use the metric operational equivalents as specified in the RVR Conversion Table (Table 1) or the Meteorological Visibility Conversion Table (Table 2) for both takeoff and landing. Values not shown may be interpolated.

b. If Applicable, Special Limitations and Provisions for Instrument… › (4) When operating at foreign airports where the published landing…

9/19/25 N 8900.752 Appendix H

Table 1 Table 2

RVR Conversion Meteorological Visibility Conversion

Feet Meters Statute Miles Meters

300 ft 75 m ¼ sm 400 m

400 ft 125 m 3/8 sm 600 m

500 ft 150 m 1/2 sm 800 m

600 ft 175 m 5/8 sm 1000 m

700 ft 200 m 3/4 sm 1200 m

1000 ft 300 m 7/8 sm 1400 m

1200 ft 350 m 1 sm 1600 m

1600 ft 500 m 1 1/8 sm 1800 m

1800 ft 550 m 1 ¼ sm 2000 m

2000 ft 600 m 1 ½ sm 2400 m

2100 ft 650 m 1 ¾ sm 2800 m

2400 ft 750 m 2 sm 3200 m

3000 ft 1000 m 2 ¼ sm 3600 m

4000 ft 1200 m 2 ½ sm 4000 m

4500 ft 1400 m 2 ¾ sm 4400 m

5000 ft 1500 m 3 sm 4800 m

6000 ft 1800 m

(4) When operating at foreign airports where the published landing minima are specified in RVR, the RVR may not be available, therefore the meteorological visibility is reported. When the minima are reported in meteorological visibility, the certificate holder must convert meteorological visibility to RVR by multiplying the reported visibility by the appropriate factor, shown in Table 3. The conversion of reported meteorological visibility to RVR is used only for Category I landing minima, and must not be used for takeoff minima, CAT II or III minima, or when a reported RVR is available.

Table 3 – [RVR = (reported meteorological visibility) X (factor)]

AVAILABLE LIGHTING DAY NIGHT

High Intensity Approach and runway lighting 1.5 2.0

Any type of lighting installation other than above 1.0 1.5

No lighting 1.0 N.A

b. Provisions and Limitations. › (3) The certificate holder may not use DA in lieu of MDA unless…

9/19/25 N 8900.752 Appendix I

Appendix I. Sample OpSpec P102, Authorized Straight-In Instrument Approach

Procedures: 14 CFR Part 135

a. The certificate holder is authorized to conduct operations using the types of instrument approach procedures (IAPs) listed in Table 1 below and must not conduct operations using any other types unless authorized by paragraph P108, Category II and Category III Instrument Approach and Landing Operations, P118, Circle to Land Operations, or P119, Category I Contact Approach Procedures, as applicable.

Table 1 – Authorized Instrument Approach Procedures

Non-Precision Approaches Without Vertical Guidance

Approaches With Vertical

Guidance (APV)

Precision Approach Procedures

(ILS & GLS)

Note: Approval for RNAV (GPS) approaches may be extended to include approval for “RNAV (GNSS)” and/or “RNP” titled approaches in foreign States. Certificate holder should consult applicable foreign Aeronautical Information Publications (AIP) and ensure navigation equipment equivalency. This approval does not extend to RNP approaches with authorization required (RNP AR).

b. Provisions and Limitations.

(1) Unless otherwise authorized by these operations specifications, the certificate holder must not use any IFR IAP at any U.S. civil, military, or joint-use airport unless:

(a) It is promulgated under 14 CFR Part 97, or

(b) The procedure has been constructed using United States Standard for Terminal Instrument Procedures (TERPS), or other criteria approved by the headquarters Flight Technologies and Procedures Division (AFS-400), or

(c) The procedure has been prescribed by the U.S. military agency operating the U.S. military airport.

(2) Runway Visual Range: TDZ RVR reports, when available for a particular runway, are controlling for all approaches to and landings on that runway.

(a) The mid RVR and rollout RVR reports (if available) provide advisory information to pilots.

(b) Visibility values below ½ statute mile are not authorized and must not be used.

(c) The mid RVR report may be substituted for the TDZ RVR report if the TDZ RVR report is not available.

(3) The certificate holder may not use DA in lieu of MDA unless paragraph P073 is authorized.

c. Provisions and Limitations for IAPs at Foreign Airports. › (4) For straight-in landing minima at foreign airports where an MDA(H)…

9/19/25 N 8900.752 Appendix I

(4) Unless otherwise authorized by paragraph P384, the certificate holder may not conduct any RNP authorization required (RNP AR) operations.

(5) Approach Procedures Using GPS or GPS Wide Area Augmentation System (WAAS). The certificate holder is authorized to conduct GPS and/or GPS WAAS instrument approach operations using the approved GPS and/or GPS WAAS equipment listed in paragraph B034 if “…. or GPS”, GPS, or RNAV (GPS) or RNAV (GNSS) is listed in Table 1 above. This authorization to conduct approaches using GPS and/or GPS WAAS is subject to the following limitations and conditions:

(a) The airborne GPS and/or GPS WAAS navigation equipment to be used must be approved for IFR operations, certified for the intended operation (LPV, LNAV/VNAV, LP or LNAV) and must contain current navigation data.

(b) Both the GPS constellation and the required airborne equipment must be providing the levels of availability, accuracy, continuity of function, and integrity required for the operation.

c. Provisions and Limitations for IAPs at Foreign Airports.

(1) Unless otherwise authorized by these operations specifications, the certificate holder must not use any IFR IAP at any foreign airport unless:

(a) The procedure has been constructed using criteria based on FAA Order 8260.3, or other criteria approved by the headquarters Flight Technologies and Procedures Division (AFS-400), or the procedure has been constructed using criteria prescribed by the ICAO Doc 8168, Procedures for Air Navigation Services, and,

(b) The visibility, RVR, or Converted Meteorological Visibility (CMV) is based on FAA Order 8260.3, or the applicable European Union (EU) or European Aviation Safety Agency (EASA) regulation or ICAO Doc 9365, Manual of All Weather Operations, Third Edition, and,

(c) The DH/MDA must not be below 200 feet HAT unless authorized by these operations specifications.

(2) The certificate holder may not conduct operations using RNP-AR or “RNP-Like” foreign procedures unless the certificate holder is authorized paragraph P384.

(3) Foreign approach lighting systems compliant with the ICAO Annex 14 Standards and Recommended Practices (SARPS) or equivalent to U.S. standards are authorized for non-precision, APV, and precision instrument approaches. Sequenced flashing lights are not required when determining the equivalence of a foreign approach lighting system to U.S. standards.

(4) For straight-in landing minima at foreign airports where an MDA(H) or DA(H) is not provided, the lowest authorized MDA(H) or DA(H) will be obtained as follows:

Appendix I. › ☐ d.

9/19/25 N 8900.752 Appendix I

(a) When an Obstruction Clearance Limit (OCL) is specified, the authorized MDA(H) or DA(H) is the sum of the OCL and the airport elevation. The MDA(H) may be rounded to the next higher 10-foot increment.

(b) When an Obstacle Clearance Altitude (OCA)/Obstacle Clearance Height (OCH) is specified, the authorized MDA(H) or DA(H) is equal to the OCA/OCH as adjusted by any operational requirement to increase the altitude/height. For non-precision approaches, the authorized MDA(H) may be expressed in intervals of 10 feet.

(5) When conducting an IAP outside the United States, the certificate holder must not operate an aircraft below the prescribed MDA(H) or continue an approach below the DA(H), unless the aircraft is in a position from which a normal approach to the runway of intended landing can be made and at least one of the following visual references is clearly visible to the pilot:

(a) Runway, runway markings, or runway lights.

(b) Approach light system (in accordance with 14 CFR § 91.175(c)(3)(i)).

(c) Threshold, threshold markings, or threshold lights.

(d) Touchdown zone (TDZ), TDZ markings, or TDZ lights.

(e) Visual glidepath indicator (such as VASI, PAPI).

(f) Runway end identifier lights.

(6) Approaches to runways with published minima as low as 1800 RVR (550m) without installed RCL and/or TDZ lighting or with inoperative RCL and/or TDZ lighting are authorized as long as the requirements of subparagraph c(1)(a-c) of this operations specification are met.

[Only select this subparagraph if the certificate holder complies with the PRM guidance and training located in 8900.1 Volume 3, Chapter 18, Section 9.]

☐ d. Precision Runway Monitor (PRM) Approaches. The certificate holder is authorized to conduct PRM approaches.

c. Operating in Vertical-lift Flight Mode: Powered-lift operating in… › (3) Straight-In Category I Precision Approach Procedures.

9/19/25 N 8900.752 Appendix J

Appendix J. Sample OpSpec P103, Straight-In Category I Approach Minima:

14 CFR Part 135

a. Except as provided in this paragraph, the certificate holder must not use any Category I IFR landing minimum lower than that prescribed by any applicable published instrument approach procedure. The IFR landing minimums prescribed in this paragraph are the lowest authorized (other than Airborne Radar approaches) for use at any airport.

b. High-Minimum PIC Provisions. A PIC who has not met the requirements of 14 CFR Part 135, § 135.225(e), and Part 194, § 194.306(vv) must use the high-minimum pilot RVR landing minimum equivalents as determined from Table 1 below.

Table 1 – High Minimum PIC RVR Landing Minimum Equivalents

RVR Landing Minimum as Published RVR Landing Minimum Equivalent required

for High-Minimum Pilots

RVR 1800 RVR 4500

RVR 2000 RVR 4500

RVR 2400 RVR 5000

RVR 3000 RVR 5000

RVR 4000 RVR 6000

RVR 5000 RVR 6000

c. Operating in Vertical-lift Flight Mode: Powered-lift operating in the vertical-lift flight mode whose aircraft flight manual (AFM) does not contain a limitation against using copter procedures are authorized to conduct straight-in precision instrument approach procedures using the following landing minimums provided that the fastest approach speed used in the final approach segment is 90 knots or less:

(1) The published Category A minimum descent altitude (MDA) or decision height (DH), as appropriate.

(2) One-half of the published Category A visibility/RVR minimum or the visibility/RVR minimums prescribed by Tables 1, 2 and 3 of this paragraph as applicable, whichever is higher.

(3) Straight-In Category I Precision Approach Procedures. The certificate holder must not use an IFR landing minimum for straight-in precision approach procedures lower than that specified in Table 2 below. Touchdown RVR reports, when available for a particular runway, are controlling for all approaches to and landings on that runway. (See Note 2.).

c. Operating in Vertical-lift Flight Mode: Powered-lift operating in… › (4) Straight-In Category I Non-Precision Approach Procedures.

9/19/25 N 8900.752 Appendix J

Table 2 – Precision Approach Minimums (Vertical-lift Flight Mode)

FULL ILS (See Note 1), MLS, or PAR

Final Approach segment at

90 Knots or less Final Approach segment

greater than 90 Knots

Approach Lights HAT Visibility (SM) TD RVR Visibility (SM) TD RVR

No Lights or ODALS or MALS

or SSALS 200 3/4 3500 3/4 4000

MALSR or SSALR or ALSF-1

or ALSF-2 200 1/4 1600 1/2 1800

MALSR with TDZ and CL or

SSALR with TDZ and CL or

ALSF-1/ALSF-2 with TDZ

and CL

200 1/4 1600 1/2 1800

Note 1: A full ILS requires an operative LOC, GS, and OM or FAF. A precision or surveillance radar fix, an NDB, VOR, DME fix, or a published minimum Glide Slope Intercept Altitude (GSIA) may be used in lieu of an outer marker.

Note 2: The midpoint RVR and rollout RVR reports (if available) provide advisory information to pilots. The midpoint RVR report may be substituted for the touchdown RVR report if the touchdown RVR report is not available.

(4) Straight-In Category I Non-Precision Approach Procedures. The certificate holder must not use an IFR landing minimum for straight-in precision approach procedures lower than that specified in Table 3 below. Touchdown (TD) RVR reports, when available for a particular runway, are controlling for all approaches to and landings on that runway. (See Note 6.)

Table 3 – Non-Precision Approach Minimums (Vertical-lift Flight Mode)

Final Approach segment at

90 Knots or less Final Approach segment

greater than 90 Knots

Approach Lights HAT (See Notes 1, 2 & 3)

Visibility

(SM) TD RVR Visibility

(SM) TD RVR

No Lights 250 3/8 2000 1 5000

ODALS or MALS

or SALS 250 3/8 (See Note 5)

1600 (See Note 5) 3/4 4000

MALSR or SSALR

or ALSF-1 or ALSF-2

250 1/4 (See Note 5)

1600 (See Note 5)

1/2 (See Note 4)

2400 (See Note 4)

DME ARC any light

Configuration 500 3/4 4000 1 5000

(1) Reduced Landing Minima – 200 feet DH and 1800 RVR. › (b) Should the FD, AP, or HUD malfunction or be disengaged during the…

9/19/25 N 8900.752 Appendix J

Note 1: For NDB approaches with a FAF, add 50 ft. to the HAT.

Note 2: For NDB approaches without a FAF, add 100 ft. to the HAT.

Note 3: For VOR approaches without a FAF, add 50 ft. to the HAT.

Note 4: For NDB approaches, the lowest authorized visibility is 3/4 and the lowest RVR is RVR 4000.

Note 5: For NDB approaches, the lowest authorized visibility is 3/8 and the lowest RVR is RVR 2000.

Note 6: The Mid RVR and Rollout RVR reports (if available) provide advisory information to pilots. The Mid RVR report may be substituted for the TDZ RVR report if the TDZ RVR report is not available.

d. Operating in Wing-borne Flight Mode or Vertical-lift Flight Mode: Powered-lift operating in wing-borne flight mode or operating in vertical-lift flight mode and whose AFM contains a limitation against using copter procedures, are authorized to conduct straight-in instrument approach procedures as follows:

(1) Standard Minimums (Precision and Non-Precision):

(a) The higher of 2400 RVR (½ SM) visibility or Table 1 as applicable.

e. Reduced Precision CAT I Landing Minima (Wing-borne Flight Mode):

(1) Reduced Landing Minima – 200 feet DH and 1800 RVR. The certificate holder is authorized precision CAT I landing minima as low as 1800 RVR to approved runways without TDZ lights and/or runway centerline (RCL) lights, including runways with installed but inoperative TDZ lights and/or RCL lights, in accordance with the following requirements:

(a) The authorized aircraft must be equipped with an approved FD (Flight Director), AP (Autopilot), or HUD (Head-Up Display) approved for at least CAT I operations that provides guidance to DA. The flightcrew must be required to engage the FD, AP, or HUD as applicable and use it to DA or initiation of missed approach unless adequate visual references with the runway environment are established that allow the safe continuation to a landing. Single pilot operations are prohibited from using the FD to reduced CAT I landing minima without the accompanying use of an AP or HUD.

(b) Should the FD, AP, or HUD malfunction or be disengaged during the approach, the flightcrew must execute a missed approach unless the approach can be continued with the use of an operational FD, AP, or HUD, or visual reference to the runway environment has been established.

9/19/25 N 8900.752 Appendix J

f. Provisions and Limitations at Foreign Airports. › (5) When conducting an IAP outside the United States, the certificate…

(c) The flightcrew must demonstrate the following type of procedures through proficiency check(s): At least one precision approach (ILS, GLS, and /or RNAV (GPS) with LPV) with a DA/HAT less than 250 feet using the FD, AP, or HUD as applicable.

(d) The Part 97 SIAP must have an 1800 RVR minimum.

f. Provisions and Limitations at Foreign Airports.

(1) If the certificate holder is authorized operations at foreign airports, the following criteria apply.

(a) The procedure has been constructed using criteria based on FAA Order 8260.3, or other criteria approved by the headquarters Flight Technologies and Procedures Division (AFS-400), or the procedure has been constructed using criteria prescribed by the ICAO Doc 8168, Procedures for Air Navigation Services, and,

(b) The visibility, RVR, or Converted Meteorological Visibility (CMV) is based on FAA Order 8260.3, or the applicable European Union (EU) or European Aviation Safety Agency (EASA) regulation or ICAO Doc 9365, Manual of All Weather Operations, Third Edition, and,

(c) The DH/MDA must not be below 200 feet HAT unless authorized by these operations specifications.

(2) The certificate holder may not conduct operations using RNP-AR or “RNP-Like” foreign procedures unless the certificate holder is authorized nonstandard paragraph P384 Required Navigation Performance (RNP) Procedures With Authorization Required (AR) and the procedures are authorized from within the applicable paragraph.

(3) Foreign approach lighting systems compliant with the ICAO Annex 14 Standards and Recommended Practices (SARPS) or equivalent to U.S. standards are authorized for non-precision, APV, and precision instrument approaches. Sequenced flashing lights are not required when determining the equivalence of a foreign approach lighting system to U.S. standards.

(4) For straight-in landing minima at foreign airports where an MDA(H) or DA(H) is not provided, the lowest authorized MDA(H) or DA(H) shall be obtained as follows:

(a) When an Obstruction Clearance Limit (OCL) is specified, the authorized MDA(H) or DA(H) is the sum of the OCL and the airport elevation. The MDA(H) may be rounded to the next higher 10-foot increment.

(b) When an Obstacle Clearance Altitude (OCA)/Obstacle Clearance Height (OCH) is specified, the authorized MDA(H) or DA(H) is equal to the OCA/OCH as adjusted by any operational requirement to increase the altitude/height. For non-precision approaches, the authorized MDA(H) may be expressed in intervals of 10 feet.

(5) When conducting an IAP outside the United States, the certificate holder must not operate an aircraft below the prescribed MDA(H) or continue an approach below the DA(H),

Appendix J. › ☐ g.

9/19/25 N 8900.752 Appendix J

unless the aircraft is in a position from which a normal transition and stabilized approach to the runway of intended landing can be made and at least one of the following visual references is clearly visible to the pilot:

(a) Runway, runway markings, or runway lights.

(b) Approach light system (in accordance with 14 CFR § 91.175(c)(3)(i)).

(c) Threshold, threshold markings, or threshold lights.

(d) Touchdown zone (TDZ), TDZ markings, or TDZ lights.

(e) Visual glidepath indicator (such as VASI, PAPI).

(f) Runway end identifier lights.

(6) Approaches to runways with published minima as low as 1800 RVR (550m) without installed RCL and/or TDZ lighting or with inoperative RCL and/or TDZ lighting are authorized as long as the requirements of subparagraph e(1)(a-c) of this operations specification are met.

[Select “Precision Runway Monitor (PRM) Approaches” authorization statement from checkbox below, if authorized.]

☐ g. Precision Runway Monitor (PRM) Approaches. The certificate holder is authorized to conduct PRM approaches.

(5) Descent below the MDA is not authorized whenever any of the… › (e) Surface mapping radar is not installed or is inoperative.

9/19/25 N 8900.752 Appendix K

Appendix K. Sample OpSpec P104, Powered-Lift Offshore Instrument Operations: Offshore Standard Approach Procedure (OSAP), Airborne Radar Approach (ARA),

and Helicopter En Route Descent Area (HEDA) Operations: 14 CFR Part 135

a. The certificate holder is authorized to conduct the following powered-lift offshore instrument operations listed in Table 1 below while operating in the vertical-lift flight mode, in accordance with the limitations and provisions of this operations specification and must not conduct powered-lift offshore instrument operations of any other type.

Table 1 – Authorized Powered-Lift Offshore Instrument Operations

Powered-

lift M/M/S

RNAV System/Radar

Offshore Operations

Additional Capabilities

Lowest Authorized

Altitude

Lowest Authorized

Visibility

Remarks, Limitations,

and Conditions Make

Model/

HW Part

Software

Part/ Ver. #

b. Limitations and Provisions. This authorization is subject to the following conditions and limitations:

(1) All operations authorized by this operations specification must be conducted in the vertical-lift flight mode and the Aircraft Flight Manual (AFM) cannot contain a limitation against using copter procedures.

(2) Descent must be entirely over water.

(3) Unless otherwise authorized by this operations specification, the certificate holder must not use any other Instrument Flight Rules (IFR) operation.

(4) The certificate holder must not use a minimum descent altitude (MDA) or visibility below the authorized values in Table 1 above.

(5) Descent below the MDA is not authorized whenever any of the following conditions exist:

(a) Any obstruction within a lateral distance of 0.5 nautical mile (NM) from the final approach course of an OSAP.

(b) Any obstruction within a lateral distance of 1 NM from the final approach course of an ARA.

(c) Any obstruction detected in the HEDA by onboard approved equipment, if not visually confirmed.

(d) A radio altimeter (RA) is not installed or is inoperative.

(e) Surface mapping radar is not installed or is inoperative.

c. Aircraft Proprietary Automated System. Use of an aircraft… › (5) The certificate holder has made revisions to the General Operations…

9/19/25 N 8900.752 Appendix K

(6) The lowest altitude used for IFR flight in any HEDA must not be lower than 400 ft above the surface.

(7) The airborne navigational equipment required to be used, including RA and weather radar (WX) with a ground mapping mode, must be approved for IFR operations.

(8) The required airborne equipment must provide the appropriate levels of availability, accuracy, continuity of function, and integrity for the operation.

(9) The operation has an approved source(s) of weather.

(10) The powered-lift must be equipped with one or more independent navigation system(s) suitable for navigating the aircraft along the route to be flown within the degree of accuracy required for Air Traffic Control (ATC) and:

(a) It can be shown that the aircraft is equipped with at least one other independent navigation system suitable, in the event of loss of the navigation capability of the single independent navigation system at any point along the route, for proceeding safely to a landing location and completing an instrument approach or offshore instrument operation; and

(b) The powered-lift has sufficient fuel so that the flight may proceed safely to a suitable landing location by use of the remaining navigation system, complete an instrument approach or offshore instrument operation, and land.

c. Aircraft Proprietary Automated System. Use of an aircraft proprietary automated system is authorized contingent upon the following conditions:

(1) The certificate holder’s powered-lift are properly modified in accordance with means approved by the FAA.

(2) The certificate holder has revised its General Maintenance Manual (GMM), inspections covering respective regulatory maintenance, and inspection programs to capture instructions for continued airworthiness (ICA) requirements.

(3) The certificate holder has revised its approved training program to establish a training and testing program for pilots that will be using the new system.

(4) The certificate holder will establish a means for the flightcrew to readily identify before flight which powered-lift have the enhanced proprietary automated system capability.

(5) The certificate holder has made revisions to the General Operations Manual (GOM) and flight deck checklist covering any procedural changes when using the automated approach system.

9/19/25 N 8900.752 Appendix K

(6) The certificate holder must not conduct such operations unless the certificate holder’s approved training program provides training for the equipment and procedures to be used.

c. Aircraft Proprietary Automated System. Use of an aircraft… › (7) The PIC and the SIC must have completed the certificate holder’s…

(7) The PIC and the SIC must have completed the certificate holder’s approved training program for the operations authorized in this operations specification.

9/19/25 N 8900.752 Appendix L

Appendix L. Sample OpSpec P105, Alternate Airport IFR Weather Minimums:

14 CFR Part 135

a. The certificate holder is authorized to conduct powered-lift operations using the alternate airport Instrument Flight Rules (IFR) weather minimums derived under the requirements of 14 CFR Part 91, §§ 91.169(c)(1)(ii)–(2) and part 194, 194.306(tt), 194.302(r)(1), as applicable, and in accordance with the provisions and limitations of this operations specification.

Appendix L. › d. Powered-lift aircraft operating in the wing-borne flight mode or…

b. IFR Alternate Airport Weather Minimums: When instrument flight rules require the certificate holder to designate an alternate airport such as takeoff alternate or destination alternate, the certificate holder must qualify the selected airport in accordance with the forecasted weather and airport capability requirements by using weather minimums derived from Table 1 or Table 2 as applicable.

c. Powered-lift aircraft operating in the vertical-lift flight mode and whose aircraft flight manual (AFM) does not contain a limitation against using copter procedures must use the weather minimums listed in Table 1 below.

Table 1 – Vertical-Lift Flight Mode IFR Alternate Airport Weather Minimums

Suitable Alternate Airport

Instrument Approach

Capability

Ceiling Visibility

Airports with at least one operational navigational facility providing a straight-in nonprecision approach procedure, or a CAT I precision approach procedure, or when applicable, a circling maneuver from an IAP.

A ceiling derived by adding 200 ft to MDA(H) or DA(H), as applicable.

1600 m or 1 statute mile (sm) but never less than the minimum visibility for the approach to be flown.

No suitable instrument flight procedure available, or no weather reporting capability present at the airport.

A ceiling allowing descent from the minimum enroute altitude (MEA), approach, and landing under basic VFR.

Visibility minimums are those allowing descent from the minimum enroute altitude (MEA), approach, and landing under basic VFR.

d. Powered-lift aircraft operating in the wing-borne flight mode or whose AFM contains a limitation against using copter procedures must use the weather minimums listed in Table 2 below.

e. Provisions and Limitations: › (7) For permitted operations outside the United States, because of…

9/19/25 N 8900.752 Appendix L

Table 2 – Wing-Borne Flight Mode IFR Alternate Airport Weather Minimums

Suitable Alternate Airport

Instrument Approach

Capability

Ceiling Visibility

For airports with at least one operational navigational facility providing a straight-in nonprecision approach procedure, or CAT I precision approach, or, when applicable, a circling maneuver from an IAP.

Add 400 ft to MDA(H) or DA(H), as applicable.

Add 1600 m or 1 statute mile (sm) to the landing minimum.

For airports with at least two operational navigational facilities, each providing a straight-in approach procedure to different suitable runways.

Add 200 ft to the higher DA(H) or MDA(H) of the two approaches.

Add 800 m or ½ sm to the higher authorized landing minimum of the two approaches used.

e. Provisions and Limitations:

(1) To use Table 1 minimums, the AFM must not contain a limitation against using copter procedures.

(2) In determining alternate airport weather minimums, the certificate holder must not use any IAP which specifies that alternate weather minimums are not authorized.

(3) The certificate holder must use only the alternate airport weather minimums derived from Table 1 or 2 as applicable. The certificate holder may apply the additive values from Table 1 or 2 to the Standard, Non-Standard, or Restricted Alternate minima, as applicable, to the suitable IAP selected at the alternate airport(s).

(4) When determining the suitability of an airport, forecast winds (including gusts) must be within operating limits (including reduced visibility limits) and within the manufacturer’s maximum demonstrated crosswind (or tailwind) limits.

(5) All conditional forecast elements below the lowest applicable operating minimums must be considered. Additives are applied only to the height value (H) rounded up to the next 100 ft value (if not a multiple of 100) to determine the required ceiling. Visibility additives should use like values (RVR additives to RVR, prevailing visibility to prevailing visibility).

(6) When dispatching under the provisions of the minimum equipment list (MEL), those MEL limitations affecting instrument approach minimums must be considered in determining alternate minimums.

(7) For permitted operations outside the United States, because of variations in the international metric weather forecasting standards, 700 m may be used in lieu of 800 m.

(9) Use of GPS-Based IAP Minimums at an Alternate Airport. › (e) The certificate holder may use suitable RNAV systems for flight…

9/19/25 N 8900.752 Appendix L

(8) The certificate holder must not use any Global Positioning System (GPS)-based instrument approach procedure (IAP) unless the certificate holder is authorized to conduct GPS-based IAP and meets the requirements in subparagraph e(5) above.

(9) Use of GPS-Based IAP Minimums at an Alternate Airport. The certificate holder may use GPS-based IAP minimums at an alternate airport with the powered-lift make, model, and series (M/M/S) listed in Table 3 below. If no authorizations appear in Table 3, GPS-based IAP minimums are not authorized at an alternate airport. Examples of GPS-based IAP include GPS, Area Navigation (RNAV) (GPS), and RNAV (Required Navigation Performance (RNP)). Use of GPS-based IAP minimums at the departure, en route, or destination alternate airport is authorized in the U.S. National Airspace System (NAS) and in any foreign State where GPS-based (or other Global Navigation Satellite System (GNSS)-based, including Satellite-based Augmentation System (SBAS)-based) approaches are authorized for alternate planning as determined by the applicable Aeronautical Information Publication (AIP).

Table 3 – GPS-Based IAP Authorizations

Powered-Lift M/M/S Conditions and Limitations Remarks

(a) Before the certificate holder is authorized to plan for the lines of minimums specified below, the certificate holder must be approved to conduct GPS-based IAP under operations specification P102, Basic Instrument Approach Procedures Authorizations—All Airports.

(b) When applicable, the certificate holder must also be approved to conduct GPS-based IAP under operations specification P122, Special Instrument Procedures for Powered-Lift Operations; and/or operations specification P123, IFR Operations for Powered-Lift Utilizing Required Navigation Performance (RNP) 0.3 En Route and Terminal Operations.

(c) For aircraft equipped with either a Technical Standard Order (TSO)-C129() or a TSO-C196() compliant navigation system a preflight receiver autonomous integrity monitoring (RAIM) prediction for the airport where the GPS-based IAP will be flown must be performed. The certificate holder must also ensure that the conventional approach (at destination) can be flown without reliance on GPS. The certificate holder must check Notices to Airmen (NOTAMs) as part of the preflight planning activities.

(d) For aircraft equipped with either a TSO-C145() or a TSO-C146() compliant navigation system, the certificate holder must review appropriate Aeronautical Information Services (AIS) and NOTAMs for wide area augmentation system (WAAS) service outages.

(e) The certificate holder may use suitable RNAV systems for flight planning at an alternate airport, provided planned availability of the substitute means of navigation is confirmed (e.g., NOTAMs and RAIM prediction for use of GPS and NOTAM/AIS checks for use of WAAS). The certificate holder may plan for a conventional approach at the destination and may plan to use a substitute means of navigation based on GPS at the alternate airport, not including substitution for the navigation aid providing lateral guidance on the Final Approach Segment (FAS), unless otherwise authorized. For example, the certificate holder may use GPS to

(f) The certificate holder may use GPS-based IAP with the powered-lift… › (iv) The aircraft must have a TSO-C145() or TSO-C146() compliant…

9/19/25 N 8900.752 Appendix L

substitute for an out-of-service Very High Frequency Omni-directional range (VOR) that supports an instrument landing system (ILS) Missed Approach Procedure (MAP) at an alternate airport (unless the procedure is “not authorized” via NOTAM).

(f) The certificate holder may use GPS-based IAP with the powered-lift M/M/S listed in Table 3 according to the conditions and limitations in subparagraphs e(9)(f)(i) through (iv), as indicated in the “Conditions and Limitations” column for each powered-lift M/M/S.

(i) The aircraft must have a TSO-C129() or TSO-C196() compliant navigation system which includes fault detection and exclusion (FDE) capability to utilize GPS-based IAP at either the destination or the alternate (not both). At the alternate, if not equipped with barometric vertical navigation (baro-VNAV) the certificate holder must only plan to use lateral navigation (LNAV) (or circling) minimum descent altitude (height) (MDA(H)).

(ii) The aircraft must have a TSO-C129() or TSO-C196() compliant navigation system that includes FDE capability and is equipped with baro-VNAV to utilize GPS-based IAP at either the destination or the alternate (not both). At the alternate, the certificate holder may plan to use LNAV (or circling) MDA(H) or LNAV/vertical navigation (VNAV) decision altitude (height) (DA(H)) if using baro-VNAV.

(iii) The aircraft must have a TSO-C145() or TSO-C146() compliant navigation system in order to utilize GPS-based IAP at both the destination and an alternate. At the alternate, if not equipped with and using baro-VNAV, the certificate holder must only plan to use LNAV (or circling) MDA(H).

(iv) The aircraft must have a TSO-C145() or TSO-C146() compliant navigation system in order to utilize GPS-based IAP at both the destination and an alternate. At the alternate, the certificate holder may plan to use LNAV (or circling) MDA(H) or LNAV/VNAV DA(H) if using baro-VNAV.

○ b. › (1) Provisions and Limitations.

9/19/25 N 8900.752 Appendix M

Appendix M. Sample OpSpec P106, IFR Takeoff Minimums: 14 CFR Part 135

a. Standard IFR Takeoff Minima: The certificate holder is authorized to use the IFR takeoff minimums specified in Table 1 subject to the provisions and limitations in this operations specification.

Table 1 – Powered-Lift Standard IFR Takeoff Minima

Condition Minimums

Two Engines or Less and Takeoff in:

• Wing-borne Flight Mode, or • Vertical-lift Flight Mode and restricted from conducting copter procedures

5000 RVR (1 SM)

Two Engines or Less and Takeoff in:

• Vertical-lift Flight Mode and not restricted from conducting copter procedures

2400 RVR (½ SM)

More than Two Engines 2400 RVR (½ SM)

(1) Provisions and Limitations:

(a) The operator must use the higher of the published takeoff minimums or the values listed in Table 1 to determine the required IFR takeoff minimums.

(b) RVR reports, when available for a particular runway, must be used for all takeoff operations on that runway.

(c) The Touchdown RVR report, if available, is controlling.

[Select Option 1 to authorize “Lower Than Standard Takeoff Minima”, OR Option 2 to authorize “Lower Than Standard Takeoff Minima” and “Approved Head Up Display (HUD)” OR Option 3 to authorize “Lower Than Standard Takeoff Minima” and “Pilot Assessment of Takeoff Visibility” OR Option 4 to authorize “ALL” three. Selecting an option is not a requirement.]

○ b. Lower Than Standard Takeoff Minima. When takeoff minima are equal to or less than the applicable standard takeoff minima, and the operation is conducted in compliance with the provisions and limitations of this operations specification, the certificate holder is authorized to use the lower than standard minima described below.

(1) Provisions and Limitations. The certificate holder must conduct all operations using the lower than standard takeoff minima described in this operations specification in compliance with Table 2 and the following

(d) RVR reports, when available for a particular runway, must be used… › (ii) For operations below RVR 1600 (500m):

9/19/25 N 8900.752 Appendix M

Table 2 – Lower Than Standard Takeoff Minima Requirements

Authorized RVR Minimum Runway Requirements

RVR 1600/500m High intensity runway lights (HIRL) or Operative runway centerline (CL) lights or Serviceable runway centerline marking (RCLM)

Touchdown (TD) – RVR 1200/350m Midpoint (Mid) – RVR 1000/300m (if installed) Rollout – RVR 1000/300m

Day: HIRL, CL lights or RCLM Night: HIRL or CL Lights

Touchdown (TD) – RVR 1000/300m Midpoint (Mid) – RVR 1000/300m (if installed) Rollout – RVR 1000/300m

CL Lights or HIRL and RCLM

Touchdown (TD) – RVR 600/175m Midpoint (Mid) – RVR 600/175m (if installed) Rollout – RVR 600/175m

HIRL and CL Lights

Touchdown (TD) – RVR 500/150m Midpoint (Mid) – RVR 500/150m (if installed) Rollout – RVR 500/150m

HIRL and CL Lights

(a) When a published takeoff minimum is greater than the applicable standard takeoff minimum and an alternate procedure (such as a minimum climb gradient compatible with airplane capabilities) is not prescribed, the certificate holder must not use a takeoff minimum lower than the published minimum.

(b) Single-engine passenger-carrying operations are not authorized.

(c) The certificate holder is authorized lower than standard takeoff minima for its 14 CFR Part 135 single-engine all-cargo operations in powered-lift aircraft. The requirements of subparagraphs d–g are not applicable to single-engine, all-cargo operations in powered-lift that are certificated for single pilot operation. However, the certificate holder must meet the takeoff performance requirements specified in 14 CFR Part 135 and Part 194.

(d) RVR reports, when available for a particular runway, must be used for all takeoff operations on that runway. All takeoff operations, based on RVR, must use RVR reports from the locations along the runway as follows:

(i) For operations at or above RVR 1600 (500m):

• The TDZ RVR report, if available, is controlling, • The mid RVR report may be substituted for an unavailable TDZ report.

(ii) For operations below RVR 1600 (500m):

• A minimum of two operative RVR reporting systems are required, • All available RVR are controlling except a far-end RVR report, which is advisory only.

○ b. › (1) Provisions and Limitations.

9/19/25 N 8900.752 Appendix M

Note: Extremely long runways (e.g., DEN 16R) utilize four RVR sensors: TDZ, mid, rollout, and far-end. When a fourth far-end RVR value is reported, it is not controlling and is not to be used as one of the two required operative RVR systems.

(e) In circumstances when RCLM or HIRL or CL Lights are not available, visibility or RVV ¼ SM may still be used, provided other runway markings or runway lighting provide pilots with adequate visual reference to continuously identify the takeoff surface and maintain directional control throughout the takeoff roll.

(f) Each aircraft must be operated with a flightcrew consisting of at least two pilots. Use of an autopilot in lieu of a required second in command (SIC) is not authorized.

(g) Each pilot station must have independently powered, operational equipment which displays a reliable indication of the following:

(i) Aircraft pitch and bank information, from a gyroscopic source.

(ii) Aircraft heading, from a gyroscopic source.

(iii) Vertical speed.

(iv) Airspeed.

(v) Altitude.

(h) Each pilot in command (PIC) must have at least 100 hours flight time as PIC in the specific make and model aircraft used under this authorization and must have satisfactorily completed the certificate holder’s approved training program which includes the methods to be used to ensure compliance with the performance limitations.

(i) Any SIC authorized by the certificate holder to manipulate the flight controls during takeoff must have at least 100 hours flight time as a pilot in the specific make and model aircraft and must have satisfactorily completed the certificate holder’s approved training program.

(j) For all takeoffs, each aircraft must be operated at a takeoff weight which permits the aircraft to achieve the performance equivalent to the takeoff performance specified in 14 CFR Part 135 and Part 194 or return to, and stop safely on, the takeoff area.

○ b. Lower Than Standard Takeoff Minima. When takeoff minima are equal to or less than the applicable standard takeoff minima, and the operation is conducted in compliance with the provisions and limitations of this operations specification, the certificate holder is authorized to use the lower than standard minima described below.

(1) Provisions and Limitations. The certificate holder must conduct all operations using the lower than standard takeoff minima described in this operations specification in compliance with Table 2 and the following

(d) RVR reports, when available for a particular runway, must be used… › (ii) For operations below RVR 1600 (500m):

9/19/25 N 8900.752 Appendix M

Table 2 – Lower Than Standard Takeoff Minima Requirements

Authorized RVR Minimum Runway Requirements

RVR 1600/500m High intensity runway lights (HIRL) or Operative runway centerline (CL) lights or Serviceable runway centerline marking (RCLM)

Touchdown (TD) – RVR 1200/350m Midpoint (Mid) – RVR 1000/300m (if installed) Rollout – RVR 1000/300m

Day: HIRL, CL lights or RCLM Night: HIRL or CL Lights

Touchdown (TD) – RVR 1000/300m Midpoint (Mid) – RVR 1000/300m (if installed) Rollout – RVR 1000/300m

CL Lights or HIRL and RCLM

Touchdown (TD) – RVR 600/175m Midpoint (Mid) – RVR 600/175m (if installed) Rollout – RVR 600/175m

HIRL and CL Lights

Touchdown (TD) – RVR 500/150m Midpoint (Mid) – RVR 500/150m (if installed) Rollout – RVR 500/150m

HIRL and CL Lights

(a) When a published takeoff minimum is greater than the applicable standard takeoff minimum and an alternate procedure (such as a minimum climb gradient compatible with airplane capabilities) is not prescribed, the certificate holder must not use a takeoff minimum lower than the published minimum.

(b) Single-engine passenger-carrying operations are not authorized.

(c) The certificate holder is authorized lower than standard takeoff minima for its 14 CFR Part 135 single-engine all-cargo operations in powered-lift aircraft. The requirements of subparagraphs d–g are not applicable to single-engine, all-cargo operations in powered-lift that are certificated for single pilot operation. However, the certificate holder must meet the takeoff performance requirements specified in 14 CFR Part 135 and Part 194.

(d) RVR reports, when available for a particular runway, must be used for all takeoff operations on that runway. All takeoff operations, based on RVR, must use RVR reports from the locations along the runway as follows:

(i) For operations at or above RVR 1600 (500m):

• The TDZ RVR report, if available, is controlling, • The mid RVR report may be substituted for an unavailable TDZ report.

(ii) For operations below RVR 1600 (500m):

• A minimum of two operative RVR reporting systems are required, • All available RVR are controlling except a far-end RVR report, which is advisory only.

(1) Provisions and Limitations. › (a) The PIC and the SIC must have completed the certificate holder’s…

9/19/25 N 8900.752 Appendix M

Note: Extremely long runways (e.g., DEN 16R) utilize four RVR sensors: TDZ, mid, rollout, and far-end. When a fourth far-end RVR value is reported, it is not controlling and is not to be used as one of the two required operative RVR systems.

(e) In circumstances when RCLM or HIRL or CL Lights are not available, visibility or RVV ¼ SM may still be used, provided other runway markings or runway lighting provide pilots with adequate visual reference to continuously identify the takeoff surface and maintain directional control throughout the takeoff roll.

(f) Each aircraft must be operated with a flightcrew consisting of at least two pilots. Use of an autopilot in lieu of a required second in command (SIC) is not authorized.

(g) Each pilot station must have independently powered, operational equipment which displays a reliable indication of the following:

(i) Aircraft pitch and bank information, from a gyroscopic source.

(ii) Aircraft heading, from a gyroscopic source.

(iii) Vertical speed.

(iv) Airspeed.

(v) Altitude.

(h) Each pilot in command (PIC) must have at least 100 hours flight time as PIC in the specific make and model aircraft used under this authorization and must have satisfactorily completed the certificate holder’s approved training program which includes the methods to be used to ensure compliance with the performance limitations.

(i) Any SIC authorized by the certificate holder to manipulate the flight controls during takeoff must have at least 100 hours flight time as a pilot in the specific make and model aircraft and must have satisfactorily completed the certificate holder’s approved training program.

(j) For all takeoffs, each aircraft must be operated at a takeoff weight which permits the aircraft to achieve the performance equivalent to the takeoff performance specified in 14 CFR Part 135 and Part 194 or return to, and stop safely on, the takeoff area

c. Approved Head-Up Display (HUD) Takeoff Guidance Systems Minima. The certificate holder is authorized to use takeoff minima of RVR 300 (75m) based upon the use of the HUD system installed in the aircraft.

(1) Provisions and Limitations.

(a) The PIC and the SIC must have completed the certificate holder’s approved training program for the operations authorized in this operations specification.

9/19/25 N 8900.752 Appendix M

(b) The certificate holder must use the HUD system to conduct the takeoffs.

(1) Provisions and Limitations. › (a) When a published takeoff minimum is greater than the applicable…

(c) HIRL and runway CL lights must be operative.

(d) Front course guidance must be displayed from a localizer that provides CAT III rollout guidance as indicated by a III/E/4 facility classification and landing minima of RVR 300. If the CAT III landing minima is greater than RVR 300 due to a localizer downgrade, these takeoffs are not authorized.

(e) Operations must be conducted to runways that are accessible by taxi routings which have operative taxiway CL lights that meet U.S. or ICAO criteria for CAT III operations; or other taxiway guidance systems approved for these operations. This taxiway guidance requirement is not applicable when operating in conditions at or above the certificate holder’s approved takeoff minima as depicted in Table 2.

○ b. Lower Than Standard Takeoff Minima. When takeoff minima are equal to or less than the applicable standard takeoff minima, and the operation is conducted in compliance with the provisions and limitations of this operations specification, the certificate holder is authorized to use the lower than standard minima described below.

(1) Provisions and Limitations. The certificate holder must conduct all operations using the lower than standard takeoff minima described in this operations specification in compliance with Table 2 and the following:

Table 2 – Lower Than Standard Takeoff Minima Requirements

Authorized RVR Minimum Runway Requirements

RVR 1600/500m High intensity runway lights (HIRL) or Operative runway centerline (CL) lights or Serviceable runway centerline marking (RCLM)

Touchdown (TD) – RVR 1200/350m Midpoint (Mid) – RVR 1000/300m (if installed) Rollout – RVR 1000/300m

Day: HIRL, CL lights or RCLM Night: HIRL or CL Lights

Touchdown (TD) – RVR 1000/300m Midpoint (Mid) – RVR 1000/300m (if installed) Rollout – RVR 1000/300m

CL Lights or HIRL and RCLM

Touchdown (TD) – RVR 600/175m Midpoint (Mid) – RVR 600/175m (if installed) Rollout – RVR 600/175m

HIRL and CL Lights

Touchdown (TD) – RVR 500/150m Midpoint (Mid) – RVR 500/150m (if installed) Rollout – RVR 500/150m

HIRL and CL Lights

(a) When a published takeoff minimum is greater than the applicable standard takeoff minimum and an alternate procedure (such as a minimum climb gradient compatible with

9/19/25 N 8900.752 Appendix M

airplane capabilities) is not prescribed, the certificate holder must not use a takeoff minimum lower than the published minimum.

(g) Each pilot station must have independently powered, operational… › (iii) Vertical speed.

(b) Single-engine passenger-carrying operations are not authorized.

(c) The certificate holder is authorized lower than standard takeoff minima for its 14 CFR Part 135 single-engine all-cargo operations in powered-lift aircraft. The requirements of subparagraphs d–g are not applicable to single-engine, all-cargo operations in powered-lift that are certificated for single pilot operation. However, the certificate holder must meet the takeoff performance requirements specified in 14 CFR Part 135 and Part 194.

(d) RVR reports, when available for a particular runway, must be used for all takeoff operations on that runway. All takeoff operations, based on RVR, must use RVR reports from the locations along the runway as follows:

(i) For operations at or above RVR 1600 (500m):

• The TDZ RVR report, if available, is controlling, • The mid RVR report may be substituted for an unavailable TDZ report.

(ii) For operations below RVR 1600 (500m):

• A minimum of two operative RVR reporting systems are required, • All available RVR are controlling except a far-end RVR report, which is advisory only.

Note: Extremely long runways (e.g., DEN 16R) utilize four RVR sensors: TDZ, mid, rollout, and far-end. When a fourth far-end RVR value is reported, it is not controlling and is not to be used as one of the two required operative RVR systems.

(e) In circumstances when RCLM or HIRL or CL Lights are not available, visibility or RVV ¼ SM may still be used, provided other runway markings or runway lighting provide pilots with adequate visual reference to continuously identify the takeoff surface and maintain directional control throughout the takeoff roll.

(f) Each aircraft must be operated with a flightcrew consisting of at least two pilots. Use of an autopilot in lieu of a required second in command (SIC) is not authorized.

(g) Each pilot station must have independently powered, operational equipment which displays a reliable indication of the following:

(i) Aircraft pitch and bank information, from a gyroscopic source.

(ii) Aircraft heading, from a gyroscopic source.

(iii) Vertical speed.

○ b. › (1) Provisions and Limitations.

9/19/25 N 8900.752 Appendix M

(iv) Airspeed.

(v) Altitude.

(h) Each pilot in command (PIC) must have at least 100 hours flight time as PIC in the specific make and model aircraft used under this authorization and must have satisfactorily completed the certificate holder’s approved training program which includes the methods to be used to ensure compliance with the performance limitations.

(i) Any SIC authorized by the certificate holder to manipulate the flight controls during takeoff must have at least 100 hours flight time as a pilot in the specific make and model aircraft and must have satisfactorily completed the certificate holder’s approved training program.

(j) For all takeoffs, each aircraft must be operated at a takeoff weight which permits the aircraft to achieve the performance equivalent to the takeoff performance specified in 14 CFR Part 135 and Part 194 or return to, and stop safely on, the takeoff area.

c. Pilot Assessment of Takeoff Visibility. The certificate holder is authorized to conduct pilot assessments of IFR Lower Than Standard Takeoff Minima when the TD RVR sensor is inoperative, or is not reported, or when actual conditions confirm that reported RVR is in error. ALL the following requirements must be met:

(1) The certificate holder has an approved procedure to determine actual visibility measured in number and type of runway lights that are seen, or markings of known spacing that are visible to the pilot when viewed from the cockpit in the takeoff position.

(2) All flight crewmembers will have completed approved training and checking in the specific procedures used to determine visibilities. Those procedures will cover the following requirements:

(a) How to determine actual visibility measured in number and type of runway lights that are seen, or markings of known spacing that are visible to the pilot when viewed from the flight deck in the takeoff position.

(b) Procedures for RVR assessment, determining that TD RVR sensor reports are in error, and takeoff and flight release coordination.

○ b. Lower Than Standard Takeoff Minima. When takeoff minima are equal to or less than the applicable standard takeoff minima, and the operation is conducted in compliance with the provisions and limitations of this operations specification, the certificate holder is authorized to use the lower than standard minima described below.

(1) Provisions and Limitations. The certificate holder must conduct all operations using the lower than standard takeoff minima described in this operations specification in compliance with Table 2 and the following

(d) RVR reports, when available for a particular runway, must be used… › (ii) For operations below RVR 1600 (500m):

9/19/25 N 8900.752 Appendix M

Table 2 – Lower Than Standard Takeoff Minima Requirements

Authorized RVR Minimum Runway Requirements

RVR 1600/500m High intensity runway lights (HIRL) or Operative runway centerline (CL) lights or Serviceable runway centerline marking (RCLM)

Touchdown (TD) – RVR 1200/350m Midpoint (Mid) – RVR 1000/300m (if installed) Rollout - RVR 1000/300m

Day: HIRL, CL lights or RCLM Night: HIRL or CL Lights

Touchdown (TD) – RVR 1000/300m Midpoint (Mid) – RVR 1000/300m (if installed) Rollout – RVR 1000/300m

CL Lights or HIRL and RCLM

Touchdown (TD) – RVR 600/175m Midpoint (Mid) – RVR 600/175m (if installed) Rollout – RVR 600/175m

HIRL and CL Lights

Touchdown (TD) – RVR 500/150m Midpoint (Mid) – RVR 500/150m (if installed) Rollout – RVR 500/150m

HIRL and CL Lights

(a) When a published takeoff minimum is greater than the applicable standard takeoff minimum and an alternate procedure (such as a minimum climb gradient compatible with airplane capabilities) is not prescribed, the certificate holder must not use a takeoff minimum lower than the published minimum.

(b) Single-engine passenger-carrying operations are not authorized.

(c) The certificate holder is authorized lower than standard takeoff minima for its 14 CFR Part 135 single-engine all-cargo operations in powered-lift aircraft. The requirements of subparagraphs d–g are not applicable to single-engine, all-cargo operations in powered-lift that are certificated for single pilot operation. However, the certificate holder must meet the takeoff performance requirements specified in 14 CFR Part 135 and Part 194.

(d) RVR reports, when available for a particular runway, must be used for all takeoff operations on that runway. All takeoff operations, based on RVR, must use RVR reports from the locations along the runway as follows:

(i) For operations at or above RVR 1600 (500m):

• The TDZ RVR report, if available, is controlling, • The mid RVR report may be substituted for an unavailable TDZ report.

(ii) For operations below RVR 1600 (500m):

• A minimum of two operative RVR reporting systems are required, • All available RVR are controlling except a far-end RVR report, which is advisory only.

(1) Provisions and Limitations. › (a) The PIC and the SIC must have completed the certificate holder’s…

9/19/25 N 8900.752 Appendix M

Note: Extremely long runways (e.g., DEN 16R) utilize four RVR sensors: TDZ, mid, rollout, and far-end. When a fourth far-end RVR value is reported, it is not controlling and is not to be used as one of the two required operative RVR systems.

(e) In circumstances when RCLM or HIRL or CL Lights are not available, visibility or RVV ¼ SM may still be used, provided other runway markings or runway lighting provide pilots with adequate visual reference to continuously identify the takeoff surface and maintain directional control throughout the takeoff roll.

(f) Each aircraft must be operated with a flightcrew consisting of at least two pilots. Use of an autopilot in lieu of a required second in command (SIC) is not authorized.

(g) Each pilot station must have independently powered, operational equipment which displays a reliable indication of the following:

(i) Aircraft pitch and bank information, from a gyroscopic source.

(ii) Aircraft heading, from a gyroscopic source.

(iii) Vertical speed.

(iv) Airspeed.

(v) Altitude.

(h) Each pilot in command (PIC) must have at least 100 hours flight time as PIC in the specific make and model aircraft used under this authorization and must have satisfactorily completed the certificate holder’s approved training program which includes the methods to be used to ensure compliance with the performance limitations.

(i) Any SIC authorized by the certificate holder to manipulate the flight controls during takeoff must have at least 100 hours flight time as a pilot in the specific make and model aircraft and must have satisfactorily completed the certificate holder’s approved training program.

(j) For all takeoffs, each aircraft must be operated at a takeoff weight which permits the aircraft to achieve the performance equivalent to the takeoff performance specified in 14 CFR Part 135 and Part 194 or return to, and stop safely on, the takeoff area.

c. Approved Head Up Display (HUD) Takeoff Guidance Systems Minima. The certificate holder is authorized to use takeoff minima of RVR 300 (75m) based upon the use of the HUD system installed in the aircraft.

(1) Provisions and Limitations.

(a) The PIC and the SIC must have completed the certificate holder’s approved training program for the operations authorized in this operations specification.

9/19/25 N 8900.752 Appendix M

(b) The certificate holder must use the HUD system to conduct the takeoffs.

(2) All flight crewmembers will have completed approved training and… › (b) Procedures for RVR assessment, determining that TD RVR sensor…

(c) HIRL and runway CL lights must be operative.

(d) Front course guidance must be displayed from a localizer that provides CAT III rollout guidance as indicated by a III/E/4 facility classification and landing minima of RVR 300. If the CAT III landing minima is greater than RVR 300 due to a localizer downgrade, these takeoffs are not authorized.

(e) Operations must be conducted to runways that are accessible by taxi routings which have operative taxiway CL lights that meet U.S. or ICAO criteria for CAT III operations; or other taxiway guidance systems approved for these operations. This taxiway guidance requirement is not applicable when operating in conditions at or above the certificate holder’s approved takeoff minima as depicted in Table 2.

d. Pilot Assessment of Takeoff Visibility. The certificate holder is authorized to conduct pilot assessments of IFR Lower Than Standard Takeoff Minima when the TD RVR sensor is inoperative, or is not reported, or when actual conditions confirm that reported RVR is in error. ALL the following requirements must be met:

(1) The certificate holder has an approved procedure to determine actual visibility measured in number and type of runway lights that are seen, or markings of known spacing that are visible to the pilot when viewed from the cockpit in the takeoff position.

(2) All flight crewmembers will have completed approved training and checking in the specific procedures used to determine visibilities. Those procedures will cover the following requirements:

(a) How to determine actual visibility measured in number and type of runway lights that are seen, or markings of known spacing that are visible to the pilot when viewed from the flight deck in the takeoff position.

(b) Procedures for RVR assessment, determining that TD RVR sensor reports are in error, and takeoff and flight release coordination.

[Select the applicable text from the following options. › (3) Operations must be conducted in accordance with RVR report…

9/19/25 N 8900.752 Appendix N

Appendix N. Sample OpSpec P108, Category II and Category III Instrument

Approach and Landing Operations: 14 CFR Part 135

a. The certificate holder is authorized to conduct [Category II/Category II and Category III] instrument approach and landing operations as authorized below using the limitations, provisions, procedures, and minimums specified in this paragraph.

b. Authorized Approach and Landing Minimums. The certificate holder is authorized to conduct the operations in subparagraph a using TDZ, mid, and rollout RVR minimums no lower than those prescribed for the specific make, model, and series (M/M/S) of aircraft listed below in Table 1 for CAT II operations and, if applicable, Table 2 for CAT III operations.

(1) For CAT II operations, TDZ RVR reports must be no lower than the approach chart minimums.

[Select the applicable text from the following options. If CAT III operations are authorized, select option 1; if CAT III operations are not authorized, select option 2. An option must be selected.]

○ (2) For all CAT III operations, TDZ and mid RVR reports must be no lower than the approach chart minimums.

OR

○ (2) CAT III operations are not authorized.

(3) Operations must be conducted in accordance with RVR report requirements in subparagraph d.

Table 1 – CAT II Aircraft Systems and Landing Minimums

Powered-Lift

M/M/S

Approach/ Landing System* DH TDZ/Mid/RO

RVR

Operational Equipment

and Limitations

Autopilot HUD FP HUD Autoland

150 DH 100 DH 1600/600/300 1200/600/300 1000/600/300

Note: * The term HUD assumes Manual HUD, HUD = CAT II certified Head-Up Display; FP HUD = CAT III certified Head-Up Display; Autopilot = autopilot use to DH followed by a manual landing; NA = Not Applicable.

Appendix N. › [Select the applicable text from the following radio-button options.

9/19/25 N 8900.752 Appendix N

Table 2 – CAT III Aircraft Systems and Landing Minimums

Powered-Lift

M/M/S

Approach/

Landing System*

Rollout System* DH/AH TDZ/Mid/RO

RVR

Operational

Equipment and Limitations

FP HUD FP Autoland FO Autoland FP Hybrid

None FP FO

50 DH 30 DH 200 AH 100 AH 50 AH

700/700/300 600/600/300 600/400/300 400/400/300 300/300/300

Note: * FP HUD = CAT III certified Head-Up Display; FP = Fail Passive Landing or Rollout Control System; FO = Fail Operational Landing or Rollout Control System; FP Hybrid = FP Autoland and FP HUD used together as a Hybrid Landing system; NA = Not Applicable.

c. Required Airborne Equipment. The flight instruments, radio navigation equipment, and other airborne systems required by the applicable section of 14 CFR and the FAA-approved AFM for the conduct of the operations authorized above in subparagraph a must be installed and operational. Any additional airborne equipment that is required must be operational and listed in Table 1 and, if applicable, Table 2.

d. Required RVR Reports. The certificate holder is authorized to conduct the operations described above in Table 1 and, if applicable, Table 2, if the following requirements for RVR reports are met. Only RVR reports for the runway of intended landing may be used.

(1) For all CAT II operations:

(a) TDZ, mid, and rollout RVR reports are controlling. Far end RVR reports are advisory.

(b) The TDZ RVR report is required.

(c) The mid RVR report is not required.

(d) The rollout RVR report is required for all operations at 1200 RVR and below, except as specified in subparagraph d(1)(e).

(e) If the rollout RVR report is unavailable, a mid or far end RVR report may be substituted. Mid RVR reports substituted for unavailable rollout reports must be 600 RVR or greater; far end reports substituted for unavailable rollout reports must be 300 RVR or greater.

(f) If only the TDZ RVR report is available, it must be at least 1400 RVR.

[Select the applicable text from the following radio-button options. If CAT III operations are authorized, select option 1; if CAT III operations are not authorized, select option 2. An option must be selected.]

9/19/25 N 8900.752 Appendix N

○ (2) For all CAT III operations:

(a) TDZ, mid, and rollout RVR reports are controlling. Far end RVR reports are advisory.

Appendix N. › f. CAT II Operations. The certificate holder is authorized to conduct…

(b) For operations using an FP landing system with an FP or FO rollout system, TDZ and either the mid or rollout RVR report are required.

(c) For operations using an FO landing system with an FP or FO rollout system, any two of the controlling RVR reports are required.

(d) For operations using a FP or FO landing system with no rollout system installed, the TDZ and mid RVR reports are required.

(e) For CAT III runways with no MID RVR sensor installed, both the TDZ and rollout RVR reports are required. In such cases, the rollout RVR report must be substituted for the missing MID RVR report.

(f) Where a far end RVR sensor is installed, the far end RVR report may be substituted for the rollout RVR report if that is not available.

(g) If the landing or rollout system degrades from FO to FP or the rollout system fails, the certificate holder is authorized to conduct operations in accordance with its MEL and AFM, using minimums no lower than those shown below (subparagraphs d(2)(g)(i)–(iii)) corresponding to the type of landing and/or rollout systems operable after the failure.

(i) Rollout system fails: Use landing minima no lower than 600/600/300 RVR.

(ii) FP landing system operable with FP or FO rollout system: Use landing minima no lower than 600/400/300 RVR.

(iii) FO landing system with FP rollout system operable: Use landing minima no lower than 400/400/300 RVR.

OR

○ (2) CAT III operations are not authorized.

e. Pilot Qualifications and Approved Training Programs. The minimums prescribed in this operations specification are authorized only for those pilots in command (PIC) and seconds in command (SIC) who have completed the certificate holder’s approved training program and who are qualified for the operations authorized above in subparagraph a by one of the certificate holder’s check pilots or an FAA inspector.

f. CAT II Operations. The certificate holder is authorized to conduct the subcategories of CAT II operations listed in Table 3 below in accordance with the other provisions of this OpSpec.

g. Operating Limitations. The certificate holder must not begin the… › (2) The crosswind component on the landing runway is less than the AFM…

9/19/25 N 8900.752 Appendix N

Table 3 – CAT II Subcategories Authorized

CAT II Operation TDZ/MID/RO

RVR Limitations

The certificate holder is authorized to conduct standard CAT II operations using autopilot or HUD to DH with a manually flown landing.

1600/600/300 1200/600/300

One of the CAT II approach systems listed in Table 1 must be used to the approach procedure DH.

The certificate holder is authorized to conduct standard CAT II operations with FP or FO CAT III Landing System.

1200/600/300 1000/600/300

Requires the use of an FP or FO Autoland or FP HUD listed in Table 1 to be flown to touchdown.

The certificate holder is authorized to conduct published SA CAT II instrument approaches and U.S. based standard CAT II instrument approaches when TDZ and/or centerline (CL) lighting are inoperative or the ALSF approach lights are operating in an SSALR or SSALS configuration

1200/600/300

Requires the use of an FP or FO Autoland or FP HUD listed in Table 1 to be flown to touchdown.

g. Operating Limitations. The certificate holder must not begin the Final Approach Segment (FAS) of an IAP authorized in subparagraph a unless the latest controlling RVR reports for the landing runway are at or above the minimums authorized for the operation being conducted and all of the following conditions are met:

(1) The following ground-based equipment must be operational:

(a) Localizer (LOC) and glideslope (GS).

(b) Outer marker or DME facility used to define the FAF unless a published waypoint or minimum GS intercept altitude fix is used in lieu of an outer marker or DME fix.

(c) For CAT II Radar Altimeter minimums Not Authorized (RA NA)-only, an inner marker to identify the DH.

(d) Runway lights: For standard CAT II and CAT III, TDZ lights, centerline (CL) lights, High Intensity Runway Lights (HIRL), or foreign equivalent. For SA CAT II, High Intensity Runway Lights (HIRL).

(e) Approach lights: For standard CAT II, Approach Lighting System with Sequenced Flashing Lights (ALSF), simplified short approach lighting system with runway alignment indicator lights (SSALR), simplified short approach lighting system (SSALS), or foreign equivalent. Sequence flashing lights (SFL) may be inoperative. For SA CAT II, medium intensity approach lighting system with runway alignment indicator lights (MALSR) is also acceptable. For CAT III, the approach lighting system may be inoperative.

(2) The crosswind component on the landing runway is less than the AFM crosswind limitations, or 15 knots or less, whichever is more restrictive.

(2) For CAT II operations without a CAT III FP or FO landing system: › (b) At the DH, if at least one of the following visual references for…

9/19/25 N 8900.752 Appendix N

(3) Once established on the FAS, all operations conducted using automatic rollout systems or FP HUD rollout guidance may continue if any RVR report decreases below the authorized minimums.

(4) The certificate holder must not conduct landing operations to any runway using autoland or FP HUD systems listed above in Table 1 or, if applicable, Table 2, unless the certificate holder determines that the flight control guidance system being used provides safe automatically (autoland) or manually (FP HUD) flown approaches and landings to be conducted at that runway.

(5) All CAT III and CAT II to 1000 RVR landing and subsequent ground operations must be conducted in accordance with the airport’s low visibility operations plan (e.g., U.S. Surface Movement Guidance and Control System (SMGCS), European Aviation Safety Agency (EASA), or ICAO criteria for CAT III operations).

(6) When conducting a CAT II or CAT III operation when the official weather observation is at or above 800 foot ceiling and 2 statute miles visibility, the crew must advise ATS of their intent and request ILS critical area protection. When conducting a CAT II or CAT III operation when the official weather observation is at or above standard CAT I minima, the crew must remain alert to any unsuitable system performance caused by a preceding arrival or departure aircraft passing through or over the ILS critical area. The operation must be discontinued if the crew is informed that ILS Critical Area protection cannot be provided, or unsuitable system performance is encountered.

h. Missed Approach Requirements. A missed approach must be initiated when any of the following conditions exist:

(1) For all CAT II operations:

(a) After passing the FAF, the approach guidance system or any other airborne equipment required for the CAT II operation being conducted becomes inoperative or is disengaged.

(b) Before arriving at DH, any of the required elements of the CAT II ground system becomes inoperative.

(2) For CAT II operations without a CAT III FP or FO landing system:

(a) At the DH, if the aircraft is not in a position from which a descent to a landing on the intended runway can be made at a normal rate of descent using normal maneuvers, and where that descent rate will allow touchdown to occur within the touchdown zone of the runway of intended landing.

(b) At the DH, if at least one of the following visual references for the intended runway is not distinctly visible and identifiable to the pilot:

○ (4) For all CAT III operations: › (c) When any GS or LOC failure occurs prior to touchdown.

9/19/25 N 8900.752 Appendix N

(i) The approach light system, except that the pilot may not descend below 100 feet above the touchdown zone elevation using the approach lights as a reference unless the red terminating bars or the red side row bars are also distinctly visible and identifiable.

(ii) The threshold.

(iii) The threshold markings.

(iv) The threshold lights.

(v) The touchdown zone or touchdown zone markings.

(vi) The touchdown zone lights.

(c) If, after passing the DH, these requirements are not continuously met.

(3) For CAT II operations with a CAT III FP or FO landing system:

(a) At the DH, if the pilot has not identified the required visual references with the TDZ or TDZ lights to verify that the aircraft will touchdown in the TDZ.

Note: In cases where the CAT II DH is higher than 100 feet above TDZE, a descent from the DH to 100 feet may be made with reference to the approach light system, except that the pilot may not descend below 100 feet above TDZE without identifying the required visual references with the TDZ or TDZ lights to verify that the aircraft will touchdown in the TDZ.

(b) If, after passing the DH, these requirements are not continuously met.

Note: If the certificate holder is authorized enhanced flight vision system (EFVS) operations under 14 CFR part 91, § 91.176(a), the certificate holder may use the EFVS to meet the visual reference requirements of subparagraphs h(2)(a) and (b) above but must still comply with all RVR and other limitations of this CAT II authorization.

[Select the applicable text from the following options. If CAT III operations are authorized, select option 1; if CAT III operations are not authorized, select option 2. An option must be selected.]

○ (4) For all CAT III operations:

(a) If the pilot determines that touchdown cannot be safely accomplished within the TDZ.

Continue reading ↓ 120 of 163 passages shown