Radar Vectors
Information for Operators Current Issued 2016 Flight Standards Service 2 pages Copy saved Nov 17, 2026

InFO 16012 Corrosion on Bell Helicopter Engine-Mount Leg-Assembly

Official source ↗ Open PDF

Distributed by: Flight Standards

http://www.faa.gov/other_visit/aviation_industry/airline_operators/airline_safety/info … An InFO contains valuable information for operators that should help them meet certain administrative, regulatory, or operational requirements, with relatively low urgency or impact on safety. The contents of this document do not have the force and effect of law and are not meant to bind the public in any way. This document is intended only to provide clarity to the public regarding existing requirements under the law or agency policies. Subject: Corrosion on Bell Helicopter Engine-Mount Leg-Assembly. Purpose: This InFO informs helicopter operators and repair facilities of potential failure of the engine- mount assemblies on Bell Helicopter models 206L1 and 206L3 due to corrosion. Background: On July 17, 2014, a Title 14 of the Code of Federal Regulations (14 CFR) Part 135, helicopter air ambulance (HAA) operator, conducted a fleet inspection of the engine mount leg assemblies on all their Bell Helicopter 206Ll and 206L3 aircraft.

The company reported, "During a recent engine change, a steel engine mount leg was discovered to be corroded from the inside out and cracked. Further inspection revealed 28 of the operator’s aircraft used the same type of steel construction for the engine mount leg assemblies. The HAA operator uses a total of 28 Bell 206Ll and 206L3 aircraft which represents 21% of their fleet. Discussion: Based on the information provided, Bell Helicopter has initiated an Operational Safety Notice (OSN); 206L-OSN-15-51, date January 21, 2015 about the engine mount leg assemblies. The company has changed the material from steel to corrosion resistant steel in the affected parts. See affected part numbers shown in the table below as part of the transition from steel to corrosion resistant steel (CRES).

Part Number Description Effectivity Tube Material

206-064-105-00I Lateral LIH leg Ll 45154-45840, L3 51001-51513 Steel

206-064-105-10I Lateral l LIH leg L3 5 1 5 1 4-SUB, L4 52001-SUB CRES

206-064-105-002 Lateral RIH leg L I 451 54-45840, L3 51 001-5151 3 Steel

206-064-105-102 Lateral RIH leg L3 51514-SUB, L4 52001-SUB CRES

206-064-106-00I FWD leg L1 451 54-45840, L3 51001-5151 3 Steel

206-064-106-I 0I FWD leg L3 51514-SUB, L4 52001-SUB CRES

206-064-107-001 AFT LIH leg L1 45154-45840, L3 51001-51513 Steel

206-064-107-I 0I AFT LIH leg L3 51514-SUB CRES

InFO

Information for Operators

U.S. Department of Transportation Federal Aviation Administration

InFO 16012 Original Issue:08/04/16 Revised 9/29/22 Flight Standards Service

Washington, DC

Distributed by: Flight Standards

Part Number Description Effectivity Tube

Material

206-064-107-I 09 AFT LIH leg L4 5200 I-SUB CRES

206-064-107-003 AFT R/H leg L145154-45840, L3 51001-51513 Steel

206-064-107-I 03 AFT R/H leg L3 51514-SUB CRES

206-064-107-111 AFT R/H leg L4 5200 I-SUB CRES

Service Difficulty Report Information. A review of the Service Difficulty Report (SDR) database for the above part numbers revealed 11 reports specifically related to engine-mount leg-assembly failure due to corrosion. The reports were submitted by air operators in the United States who use this type of aircraft. Recommended Action: Operators and repair facilities should familiarize themselves with the information in this InFO, as well as applicable Bell Helicopter Bulletins, Notices and Letters regarding the engine- mount leg-assembly, to be aware of and reduce the risk of possible accidents caused by corrosion. Operators and repair facilities should also pay close attention to the engine mount areas and associated components during inspections for signs of corrosion. Currently there are 201 BHT-206L1 and 203 BHT-206L3 aircraft registered in the United States that may be affected. Contact: Questions or comments regarding this InFO should be directed to the Aircraft Maintenance Division at (202) 267-1675, or via email at [email protected].