Radar Vectors
Handbook Historical Issued Jan 1965 434 pages Copy saved Nov 19, 2026

Aerodynamics for Navy Aviators

This document is historical. It may have been replaced. Check the official source before relying on it.

Official source ↗ Official PDF ↗

Text read by OCR from a scanned file (20 of 434 pages). Check the original, as some words may be misread.

TITLE

NA VAIR 00·801·80 AERODYNAMICS FOR NAVAL

AVIATORS

BY

H. H. HURT, JR.

UNIVERSITY OF SOUTHERN CALIFORNIA

DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. DESTRUCTION NOTICE - For unclassified, limited documents, destroy by any method that will prevent disclosure of contents or reconstruction of the document.

PUBLISHED BY DIRECTION OF COMMANDER, NAVAL AIR SYSTEMS COMMAND

REVISED JANUARY 1965 0800LP1114462

LIST OF CHANGED PAGES ISSUED

Reproduction for non-military use of the information or illustrations contained in this publication is not permitted without specific approval of the issuing service (NA VAIR or USAF). The policy for use of Classified Publications is established for the Air Force in AFR 205-1 and for the Navy in Navy Regulations, Article 1509 • ...------------- LIST OF CHANGED PAGES ISSUED

A

INSEIf LATEST C_ PAGES. DESTROY SUPERSEDED PAGES.

NOTE: The portion of the tut .ff'ecr:ecl by the current change ia indicated by • vertical line in the OUter margins

of the page.

• The aateritlt indicate. pagel dwtged, added or deleted by the turrent change,

ADDITIONAL COPIES OF THIS PUBLICATION MAY BE OBTAINED AS FOLLOWS,

USAF AC'flVITlES-In accordance with Technical Order No. 00-5-1. NA VY ACTIVmE~UJe DO FORM U'" and fllbmit in accordance with the inKruC:JiODi contained in NAVSUP PUB-

LICATION -4'7-Military Standard Requilitioning and Issue Procedures. Fot information on othtl' available maurW Ind details of distribution refer to NAVSUP PUBLICATION 2002 SECTION VIII, PART c .. d NAVAIR OO·IOOA. '

NAVAIR

NOTICE - 02 JANUARY 1965

NAVAIR 00-80T-80

02 JANUARY 1965

NAVAIR 00-80T-80 DATED 01 JAUARY 1965 CHANGED THE DISTRIBUTION STATEMENT AND DESTRUCTION NOTICE ON THE TITLE PAGE. PLEASE REMOVE AND DISCARD TITLE AND A PAGE AND REPLACE WITH ATTACHED CORRECTED COPY.

PLACE THIS NOTICE SHEET BEHIND TITLE PAGE AFTER COMPLETING REQUIRED ACTION.

NOTICE

NOTICE

NOTICE

NOTICE

0801LP1093899

0800LP1114462

PREFACE

PREFACE

The purpose of this textbook is to present the elements of applied aerodynamics and aeronautical engineering which relate directly to the problems of flying operations. All Naval Aviators possess a natural interest in the basic aerodynamic factors which affect the performance of all aircraft. Due .to the increasing complexity of modern aircraft, this natural interest must be applied to develop a sound understanding of basic engineering principles and an appreciation of some of the more advanced problems of aerodynamics and engineering. The safety and effectiveness of flying operations will depend greatly on the under- standing and appreciation of how and why an airplane flies. The principles of aerodynamics will provide the foundations for developing exacting and precise flying techniques and operational procedures.

The content of this textbook has been arranged to provide as com- plete as possible a reference for all phases of flying in Naval Aviation. Hence, the text material is applicable to the problems of flight train- ing, transition training, and general flying operations. The manner of presentation throughout the text has been designed to provide the elements of both theory and application and will allow either directed or unassisted study. As a result, the text material’will be applicable to supplement formal class Iectures and briefings and provide reading material as a background for training and flying operations.

Much of the specialized mathematical detail of aerodynamics has been omitted wherever it was considered unnecessary in the field of flying operations. Also, many of the basic assumptions and limita- tions of certain parts of aerodynamic theory have been omitted for the sake of simplicity and clarity of presentation. In order to contend with these specific shortcomings, the Naval Aviator should rely on the assistance of certain specially qualified individuals within Naval Avia- tion. For example, graduate aeronautical engineers, graduates of the Test Pilot Training School at the Naval Air Test Center, graduates of

the Naval Aviation Safety Officers Course, and technical representatives of the manufacturers are qualified to assist in interpreting and applying the more difficult parts of aerodynamics and aeronautical engineering. To be sure, the specialized qualifications of these individuals should be utilized wherever possible.

iii

NAVWEPS 00-801-80 PREFACE

The majority of aircraft accidents are due to some type of error of the pilot. This fact has been true in the past and, unfortunately, most probably will be true in the future. Each Naval Aviator should strive to arm himself with knowledge, training, and exacting, professional attitudes and techniques. The fundamentals of aerodynamics as pre- sented in this text will provide the knowledge and background for safe and effective flying operations. The flight handbooks for the air- craft will provide the particular techniques, procedures, and operating data which are necessary for each aircraft. Diligent study and continu- ous training are necessary to develop the professional skills and tech- niques for successful flying operations.

The author takes this opportunity to express appreciation to those who have assisted in the preparation of the manuscript. In particular, thanks are due to Mr. J. E. Fairchild for his assistance with the por- tions dealing with helicopter aerodynamics and roll coupling phenom- ena. Also, thanks are due to Mr. J. F. Detwiler and Mr. E. Dimitruk for their review of the text material.

HUGH HARRISON HURT, Jr. August 1959 University of Southern California Los Angelesj Cnlif.

iv

NAVWEPS OO-801-8O

TABLE OF CONTENTS

TABLE OF CONTENTS

TABLE OF CONTENTS

PREFACE.. ,., . iii

CHAPTER I: BASIC AERODYNAMICS

WING AND AIRFOIL FORCES

PROPERTIES OF THE ATMOSPHERE. 1

Static pressure Temperature Density Viscosity Standard atmosphere Pressure altitude Density altitude

BERNOULLI’S PRINCIPLE AND SUBSONIC AIRFLOW.. 4

Bernoulli’s equation,

Incompressible tlow

6

Variation of static pressure and velocity Kinetic and porcntial energy of flow Static and dynamic prcssurc, 4 Factors affecting dynamic pressure

Airspeed measurement.. . .

Stagnation prcssurc

9

Measurement of dynamic pressure

Pitot and static sources Indicated airspeed

DEVELOPMENT OF AERODYNAMIC FORCES..

Streamline pattern and pressure distribution. Generatioaoflift …

Circulation Pressure distribution

… 14

… 14 … 16

Airfoil terminology. Aerodynamic force coefficient . .

‘,:

Basic lift equation 2 3 Lift coefficient Dynamic prcssurc and surface area

”

NAVWEPS OO-EOT-80 TABLE OF CONTENTS

Interpretation of the lift equation.. . … .

Lift cocfficicnt versus angle of attack Stall speed and angle of attack Angle of attack versus velocity Primary control of airspeed … mrfou un cnacactectsucs. . . .

Section angle of attack and lift coefficient Ty ical section chvactctistics E&t of thickness and cambet Drag characteristics, . . . . . . . :.

Drag equation Drag cocficicnt versus angle of attack Lift-drag ratio Power-off glide pctformancc

Airfoil drag chanwteristics.. ) . . .

Section drag cocfficicnt Ty ical section characteristics E 2 ect of thickness and cunbcr Low drag sections FLIGHT AT HIGH LIFT CONDITIONS. . . . . . . . StaII speeds. . … . . .,. …

Maximum lift cc&cicnt Stall angle of attack ..,e * . . ~lrecrorwergnt … Effect of maneuvering flight,. .

Load factor ~ets~s bank angle Stall spad versus load factor

Effect of high lift devices., .

Effect on stall speed

Stall angle of attack and stall recovery. . . . . . HIGH LIFT DEVICES.

Types of high lift devices., .

Plain flap S S otted flap P

lit flap

Fowler flap Slots and slats

Boundary layer control

Operation of high lift devices.

Flap retraction and extension

Chan Effect o f

es in lift, drag, and trim

power DEVELOPMENT OF AERODYNAMIC PITCHING MOMENTS

Pressure distribution. .~. : . ! . : Center of pressure and aerodynamic center. Pitching moment coefficient. . ,

Effect of camber Effect of flaps Relationship between center of pressure, aerodynamic centet, and moment coefficient

Application to longitudinal stability. .

Stability and trim Effect of supersonic flow

PW

23

27

29

33

35

3.5

::

37

39

39 41

43

a: 49

51

vi

NAVWEPS OO-BOT-BO

TABLE OF CONTENTS

FRICTION EFFECTS.

Viscous Bow.. Boundarglayers …

Laminar flow Transition Turbulent flow

ReyooldsNumber …

Definition Skin friction versus Reynolds Number

Airflowseparatioa …

Pressure distribution Prcswrc gradient and boundary layer energy Factors affecting separation

Scaleeffect …

Effect on aerodynamic characteristics Reynolds Number correlation

PLANFORM EFFECTS AND AIRPLANE DRAG

EFFECT OF WING PLANFORM.. . . Descr1puon of planform

Area, span,, and chord Aspect ratm and taper Sweepback Mean aerodynamic chord Development of lift by a wing.. .

vortex system Ti and bound vortices I&cd flow and downwash Scction angle of attack Induced angle of attack

INDUCED DRAG. :

Induced angle of attack and inclined lift. Induced drag coefficient,

Effect of lift coefficient Effect of aspect ratio

Effectoflift … Effea of altitude.. EffectofsPeed … Effect of aspect ratio.

Lift and dra Influcncc of ow aspxt ratio configurations f

characteristics

EFFECT OF TAPER AND StiEEPtiACK.

Spanwise lift distribution localinducedflow … Effect on lift and drag characteristics. .‘,

STALL PATI’ERNS.

Pnvorablestallpattern … EffeaofpIanform …

Taper Sweepback

Modifications for stall characteristics.

vii

52

52 52

54

56

59

61

61

63

66

66 68

68

2; 71

74

74 76 76

77

::

NAVWEPS 00-801-80 TABLE OF CPNTENTS

PARASITE DRAG.

Sources of parasite drag. . Parasite drag coefficient.. . . . Parasite and induced drag.

Mi.li$z’.?1 p”‘““ite dr2g CxEciczt Airplane efficiency factor Equivalent parasite area

Effect of configuration. Effect of altitude., Effectofspeed …

AIRPLANE TOTAL DRAG..

Drag variation with speed Induced and parasite drag Stall speed Minimum drag Specific performance conditions Compressibility drag rise

CHAPTER 2. AIRPLANE PERFORMANCE

REQUIRED THRUST AND POWER

DEFINITIONS.

Pan&e 14 ;n&Ced drw _ _.- … - _- Thrustandpowerrequir~~:::::::::::::::::::::::::::::::::::::::::

VARIATION OF THRUST AND POWER REQUIRED

Effect of gross weight. Effect of configuratmn. Effect of altitude.

AVAILABLE THRUST AND POWER

PRINCIPLES OF PROPULSION.

Mass flow, velocity change, momentum change.. Newton’s laws, Wastedpower … : … Power available. Propulsion efficiency.

TURBOJET ENGINES

Operatingcycle … Function of the components.

Inlet or diffuser Compressor Combustion chamber Turbine Exhaust nozzle

Turbojet operating characteristics.. :_

Thrust and power available Effect of velocity Effect of engine speed Specific fuel consumption Effect of altitude Governing apparatus Steady state, acceleration, deceleration Instrumentation

viii

*am 87

87

91

;:

92

96

$6 97

99 101 101

104

104 104 104 106 106

107 109

116

NAVWEPS 00-SOT-80

TABLE OF CONTENTS

Pam Turbojet operating limitations 124 Exhaust gas temperature b&pr~$or stall or surge

Compressor inlet air temperature Engine speed Time limitations Thrust augmentation. 129

Afterburner Water injection The gas turbine-propeller combination. 132 Equivalent shaft horsepower Governing requirements Operating limitations performance characteristics

THE RECIPROCATING ENGINE, 135

Operating chatacterlsucs. . . 135

Operating cycle Brake horsepower Torque, RPM, and BMEP Normal combustion Preignition and detonation Fuel qualities Specific fuel consum tion Effect of altitude an supercharging 8 Effect of humidity

Operating limitations. 144 Detonation and preignition Water injection Time limitations Reciprocating loads AIRCRAFT PROPELLERS

Operating characteristics, 145

Flow patterns Propulsive cficiency Powerplant matching Governing and feathering

Operating limitations.. 148

ITEMS OF AIRPLANE PERFORMANCE

STRAIGHT AND LEVEL FLIGHT. 150 Equilibrium conditions Thrust and power required Thrust and powec available Maximum and minimum speed

CLIMB PERFORMANCE. 150 Steady and transient climb. 150 Forces acting on the airplane Climb angle and obstacle clcarancc Rate of climb, primary control of altitude Propeller and jet aircraft

Climb performance. 156 Effect of weight and altitude

Descending flight

ix

NAWEPS 00-801-8~ TABLE OF CONTENTS

RANGE PERFORMANCE. :;

General range performance. 158

Specific range, v&city, fuel flbw Specific endurance Cruise control and total range Range, propeller driven airplanes. 160

Aerodynamic conditions Effect of weight and altitude Reciprocating and turboprop airplanes

Range, turbojet airplanes. :. 164

Aerodynamic conditions Effect of weight and altitude Constant altitude and cruise-climb profiles

Effect of wind oh ‘PY~C … , … 168

ENDURANCE PERFORMANCE. 170

General endurance performance.. :. . 170

Spxific cndurancc, velocity, fuel flow

Effect of altitude op endurance, : . . . . . . 170

Propcllcr driven airplanes Turbojet aitplaocs

OFF-OPTIMUM RANGE AND ENDURANCE. 172

Reciprocating powered airplane.. 172 Turboprop powered airplane, , . . . 173 Turbojet powered airplane... . . I.. . 175

MANEUVERING PERFORMANCE. 176

Relationships of turning flight. . . . . . . 176

Steady turn, bank angle and load factor Induced drag Turning performance.. . . 178

Tom radius and turn rate Effect of bank aaglc and velocity Tactical performance, . 178

Maximum lift

FhZZF%3:~2:; pfOt”l~“CC

TAKEOFF AND LANDING PERFORMANCE.. .~, 1132

Relationships of accelerated motion. . 182

Acceleration, vclocit distance Uniform and nonum arm acceleration ,J

Takeoff performance.. . . . 164

Forces acting on the airplane Accelerated motion Factors of technique

Factors affecting takeo# performance. . 187

Effect of gross weight Rffcct of wind Effect of runway slope F’qxt takeoff vcloclty. Effect of altitude and tempcraturc Handbook data

Y

NAVWEPS OO-BOT-BO

TABLE OF CONTENTS

Landing performance.. . . . . 192

Forces acting on the airplane Accclanted motion Factors of technique Factors affecting landing performance. . . . 196

E&t of gross weight Effect of wind

Fg; ~~~~~~~;mpcntwc ro a Impmtance of handbook performance data. . . 200

CHAPTER 3. HIGH SPEED AERODYNAMICS

GENERAL CONCEPTS AND SUPERSONIC FLOW PATTERNS

NATURE OF COMPRESSIBILITY. …

Definition of Mach number … Sttbsonic, traasonic, supersonic, and hypersonic flight regimes … Compressible flow conditions … Comparison of compressible and incompressible flow …

TYPICAL SUPERSONIC FLOW PATTERNS., …

Obliqueshockwave … Normalshockwave … Ex nsionwave E t9”

… ect on velocity, Mach number, density, pressure, energy. .. : …

SECTIONS IN SUPERSONIC FLOW. …

nowpatterns … Pressure distribution. … Wavedrag … Location of aerodynamic center …

201

202 204 204 204

207

207 207 211 213

213

213 213 21s 21s

CONFIGURATION EFFECTS

TRANSONIC AND SUPERSONIC FLIGHT. . 215 Critical Mach ntlm~r 2 15 Shock wave formatton. … 218 Shock induced separation.. i.. Porcedivergence …

$2:

Phenomena of transonic flight.. . 218 Phenomena of supersonic Bight.. . 220

TRANSONIC AND SUPERSONIC CONFIGURATIONS. 220

Airfoil sections.. . 220 Transonic sections Supctsonic sections Wave drag characteristics Effect of Mach number on airfoil characteristics

Plaaform effects. , … , … 226 Effect of swcc ack p” Advantages o swcepback Disadvantages of sweepback Effect of nspct ratio and tip shape

Control surfaces. . … 236 Powered controls All movable surfaces

NAWEPS 00-801-80 TABLE OF CONTENTS

Supersonic engine inlets. . 238 Internal and external comprcsrion inlets Inlet performance and powerplant matching

Supersonic configurations. 240

AERODYNAMIC HEATING. 242

Ram temperature rise.. _. 242 Effect on structural materials and powerplant performance. 242

CHAPTER 4. STABILITY AND CONTROL

DEFINITIONS

STATIC STABIL .ITY … DYNAMIC STAB1 ‘LITY … TRIM AND CONTROLLABI ,LITY … AIRPLANE REFERENCE AXES …

LONGITUDINAL STABILITY AND CONTROL

STATIC LONGITUDINAL STABILITY. …

Generalconsiderations:. .. :,_~ … … .:..1... ... Contribution of the component surfaces … Wing Fuselage and nacelles Horizontal tail Power-off stability … Powereffects … Control force stability. … Maneuveringstability … Tailoring control forces …

LONGITUDINAL CONTROL …

Maneuvering control requirement. … Takeoff control requirement. … Landing control requirement. …

LONGITUDINAL DYNAMIC STABILITY. …

Phugoid … Short period motions …

MODERN CONTROL SYSTEMS …

Conventional Boosted Power operated

DIRECTIONAL STABILITY AND CONTROL

DIRECTIONAL STABILITY. …

Defimtuxu … ...

Contribution of the airplane components …

Vertical tail Wing Fuselage and nacelles Power effects .. Crawal conditions. …

DIRECTIONAL CONTROL … > …

Directional control requirements … … Adverseyaw …

xii

243 245 247 249

250

-25’0.

253

259 259 264 268 270

275

275 275 277

279

279 281

281

284

284

285

290

290

291 291

NAVWEPS 00-BOT-80

TABLE OF CONTENTS

Spinrecovety..; … Slipstream rotatmn. … Cross wind takeoff and landing. … Asymmetrical power …

LATERAL STABILITY AND CONTROL LATERAL STABILITY, …

Definlttons … CONTRIBUTION OF THE AIRPLANE COMPONENTS.

Wing … ~ … ~ Fuselage and wmg powton, …

Sweepback … Vertical tail … LATERAL DYNAMIC EFFECTS, …

Directional divergence Spiral divergence Dutch roll CONTROL IN ROLL … . . Rolhsg motmn of an airplane … Roliing performance, … Critical requirements. …

MISCELLANEOUS STABILITY PROBLEMS LANDING GEAR CONFIGURATIONS …

Tail wheel type Tricyde type Bicycle type SPINS AND PROBLEMS OF SPIN RECOVERY …

Principal prospin moments Fundamental principle of recovery Effect of configuration PITCH-UP., …

Definition

Contribution of the airplane components EFFECTS OF HIGH MACH NUMBER..

Longitudinal stability and control Directional stability Dynamic stability and damping PILOT INDUCED OSCILLATIONS.. _.

Pilot.control system-airplane coupling High q aed low stick force stability ROLL COUPLING.

Inertia and aerodynamic coupling Inertia and wind axes Natural pitch, yaw, and coupled pitch-yaw frequencies Critical roll rates Autorotative rolling Operating limitations HELICOPTER STABILITY AND CONTROL.

Rotor gyroscopic effects

Cyclic and collective pitch Lon

f

itudinal, lateral, and directional control Ang e of attack and velocity stability

Dynamic stability

xiii

Pace 291 294 294 294

294

295

295

298 298 298 298

299

300

300 301 305

305

307

313

313

314

315

319

NAVWEPS OO-BOT-80 TABLE OF CONTENTS

CHAPTER 5. OPERAilNG STRENGTH LIMITATIONS

GENERAL OEFlNlTlONS AND STRUCTURAL REQUlREMENTS

STATIC STRENGTH … ~.~~~.~ ~..~

Limit load Factor of safety Material properties

SERVICE LIFE

Pati Loa r

e consideration spectrum attd cumulative damage Creep considerations

AEROELASTIC EFFECTS.

Stiffness and rigidity

AIRCRAFT LOADS AND OPERATING LIMITATIONS FLIGHT LOADS-MANEUVERS AND GUSTS.

Loadfactor …

Maneuvering load factors.. .I Maximum lift capability Effect of gross weight ^ . ._ ClllStlOadtacfors … , …

Gust load increment Effect of gust intensity and lift curve slope Effect of wing loading and altitude Effect of overstrea.

THE V-n OR V-g DIAGRAM.

Effect of weight, configuration;altihtde, and symmetry of Ior-Ang Limit load factors Ultitnute load facvxs

Maximum lift capability Limit airspeed Operating env+pe Maneuver’speed and penetration of turbulence

EFFECT OF HIGH SPEED FLIGHT..

Critical gust Aileron reversal Divergence PIutter Compressibility problems

LANDING AND GROUND LOADS.

Landing load factor Effect of touchdown rate of descent Effect of gross weight Ported landing on unprepared .surfaces

EFFECT OF OVERSTRESS ON SERVICE Recognition of overstress’damage Importance of operating limitations

LIFE

,... ,..,

328

330

331

331 331

332

,’ 334

334

339

343

344

xiv

NAVWEPS 00401-80

TABLE OF CONTENTS

CHAPTER 6. APPLICATION OF AERODYNAMICS TO

SPECIFIC PROBLEMS OF FLYING

mrx PRIMARY CONTROL OF AIRSPEED AND ALTITUDE.. 349

Angle of attack versus airspeed Rate of climb and descent Flying technique

REGION OF REVERSED COMMAND. . 353

Regions of normal and reversed command Features of flight in the normal and reversed regions of command

THE ANGLE OF ATTACK INDICATOR AND THE MIRROR LANDING SYSTEM. . . 357

The angle of attack indicator The mirror landing system

THE APPROACH AND LANDING., 360

The approach The landing flare and touchdown Typical errors

THE TAKEOFF.. 365

Takeoff speed and distance Typical errors

GUSTS AND WIND SHEAR.. _. t,. 367 Vertical and horizontal gusts

POWER-OFF GLIDE PERFORMANCE. . 369 Glide angle and lift-drag ratio Factors affecting glide performance The flameout pattern

EFFECTOF ICE AND FROST ON AIRPLANE PERFORMANCE.. 373

Effect of ice Effect of frost

ENGINE FAILURE ON THE MULTI-ENGINE AIRPLANE. 376

Effecf of weight and altihtde Control requirements Effeti on performance Etrect of turning flight and configuration

GROUND EFFECT., _, 379

Aerodynamic influence of ground effect Ground effect on specific flight conditions

INTERFERENCE BETWEEN AIRPLANES IN FLIGHT.. 383

Effect of lateral, vertical, and IongiNdinal separation Collision possibility

NAVWEPS 00-BOT-BO TABLE OF CONTENTS

BRAKING PERFORMANCE. …

Friction cbaracte~istics Braking technique Typical errors of braking technique

REFCTSAL SPEEDS , LINE SPEEDS, AND CRITICAL FIELD LENGTH. …

Refusal speed

Line speeds Critical field length, multi-engine operation

SONIC BOOMS …

Shock waves and audible sound Precautions

HELICOPTER PROBLEMS …

Rotoraerodynamics … Retreating blade stall … Compressjbility effects … Autorotatton charactertsttcs … Powersettling …

THE FLIGHT HANDBOOK. … SELECTED REFERENCES. … Iklr\C” ,,“YL)\ …

Pam

387

391

396

399 400 402 404 405 408

411

413

414

xvi

Chapter 1 - BASIC AERODYNAMICS

NAVWEPS 00-BOT-BO BASIC AERODYNAMICS

Chapter 1

BASIC AERODYNAMKS

In order to understand the characteristics of his aircraft and develop precision flying tech- niques, the Naval Aviator must be familiar with the fundamentals of aerodynamics. There are certain physical laws which describe the behavior of airflow and define the various aerodynamic forces and moments acting on a

surface. These principles of aerodynamics pro- vide the foundations for good, precise flying techniques.

WING AND AIRFOIL FORCES

PROPERTIES OF THE ATMOSPHERE

The aerodynamic forces and moments acting on a surface are due in great part to the prop- erties of the air mass in which the surface is

operating.~ The composition, of the earth’s atmosphere by volume is approximately 78 percent. nitrogen, 21 percent oxygen, and 1

NAVWEe3 OO-BOT-80 BASIC AERODYNAMICS

percent water vapor, argon, carbon dioxide, etc. For the majority of all aerodynamic con- siderations air is considered as a uniform mixture of these gases. The usual quantities used to define the properties of an air mass are as follows:

STATIC PRESSURE. The absolute static pressure of the air is a property of primary

importance. The static pressure of the air at any altitude results from the mass of air supported above that level. At standard sea level conditions the static pressure of the air is 2,116 psf (or 14.7 psi, 29.92 in. Hg, etc.) and at 40,000 feet altitude this static pressure decreases to approximately 19 percent of the sea level value. The shorthand notation for the ambient static pressure is “p” and the standard sea level static pressure is given the

subscript “a” for zero altitude, pa. A more usual reference in aerodynamics and perform- ance is the proportion of the ambient sta~tic pressure and the standard sea level static pressure. This static pressure ratio is assigned

the shorthand notation of 8 (delta).

Altitude pressure ratio

Ambient static pressure =Standard sea level static pressure

6 = PIP0

Many items of gas turbine engine perform- ance are directly related to some parameter involving the altitude pressure ratio. TEMPERATURE. The absolute tempera- cure of the air is another important property. The ordinary temperature measurement by the Centigrade scale has a/datum at the freezing point of water but absolute zero temperature

is obtained at a temperature of -273“ Centi- grade. Thus, the standard sea level tcmpera- ture of 15” C. is an absolute temperature of 288”. This scale of absolute temperature using the Centigrade increments is the Kelvin scale, e.g., o K. The shorthand notation for the ambient air temperature is “T” and the stand- ard sea level air temperature of 288’ K. is signified by Ta. The more usual reference is,

the proportion of the ambient air temperature and the standard sea level air temperature. This temperature ratio is assigned the short- hand notation of 0 (theta).

Temperature ratio

Ambient air temperature =Standard sea level air temperature @=TITtl ,+273

288

Many items of compressibility effects and jet engine performance involve consideration of the temperature ratio.

DENSITY. The density of the air is a prop- erty of greatest importance in the study of aerodynamics. The density of air is simply the mass of air per~cubic foot of volume and

is a direct measure of the quantity of matter in each cubic foot of air. Air at standard sea lcvcl conditions weighs 0.0765 pounds per cubic foot and has a density of 0.002378 slugs per cubic foot. At an altitude of 40,000 feet the air density is approximately 25 percent of the sea level value.

The shorthand notation used for air density is p (rho) and the standard sea level air density is then pO. In many parts of aerodynamics it is very convenient to consider the proportion of the ambient air density and standard sea level air density. This density ratio is assigned the shorthand notation of c (sigma).

density ratio= ambient air density standard sea level air density

a = PIP0

A general gas law defines the relationship of pressure temperature, and density when there is no change of state or heat transfer. Simply stated this would be “density varies directly with pressure, inversely with temperature.” Using the properties previously defined,

density ratio= Pressure rat’o. temperature rat10

5550 NAVY

BASIC AERODYNAMICS NAVWEPS 00-80T-80

PlAVWEPS 00-8OT-80 BASIC AERODYNAMICS

This relationship has great application in aerodynamics and is quite fundamental and necessary in certain parts of airplane perform- ance.

VISCOSITY. The viscosity of the air is important in scale and friction effects. The coefficient of absolute viscosity is the propor- tion between the shearing stress and velocity gradient for a fluid flow. The viscosity of gases is unusual in that the viscosity is gen- erally a function of temperature alone and an

increase in temperature increases the viscosity. The coefficient of absolute viscosity is assigned the shorthand notation I, (mu). Since many parts of aerodynamics involve consideration of viscosity and density, a more usual form of viscosity measure is the proportion of the co- efficient of absolute viscosity and density. This combination is termed the “kinematic viscosity” and is noted by Y (nu).

kinematic viscosity

cc coefficient of absolute viscosity

density

v=PlP

The kinematic viscosity of air at standard sea level conditions is 0.0001576 square feet per second. At an altitude of 40,000 feet the kinematic viscosity is increased to 0.0005059 square foot per second.

In order to provide a common denominator for comparison of various aircraft, a standard

atmosphere has been adopted. The standard atmosphere actually represents the mean or average properties of the atmosphere. Figure 1.1 illustrates the variation of the most im- portant properties of the air throughout the standard atmosphere. Notice that the lapse rate is constant in the troposphere and the stratosphere begins with the isothermal region.

Since all aircraft performance is compared and,evaluated in the environment of the stand- ard atmosphere, all of the aircraft instrumenta- tion is calibrated for the standard atmosphere.

Thus, certain corrections must apply to the instrumentation as well as the aircraft per- formance if the operating conditions do not fit the standard atmosphere. In order to prop- erly account for the nonstandard atmosphere certain terms must be defined. Pressure .&itudc is the altitude in the standard atmosphere corresponditrg to a particular pressure. The aircraft altimeter is essentially a sensitive barometer calibrated to indicate altitude in the staotlard atmosphere. If the altimeter is set for 29.92 in. Hg the altitude indicated is the pressure altitude-the altitude in the stand- ard atmosphere corresponding to the sensed pressure. Of course, this indicated pressure altitude may not be the actual height above sea level due to variations in remperature, lapse rate; atniospheric pressure, and possible errors in the sensed pressure.

The more appropriate term for correlating aerodynamic performance in the nonstandard atmosphere is density &it&-the altitude in the standard atmosphere corresponding to a particular value of air density. The computa- tion of density altitude must certainly involve consideration of pressure (pressure altitude) and temperature. Figure 1.6 illustrates the manner in which pressure altitude and tem- perature combine to produce a certain density altitude. This chart is quite standard in use and is usually included in the performance section of the flight handbook. Many subject areas of aerodynamics and aircraft performance will emphasize density altitude and temperature as the most important factors requiring con- sideration.

BERNOULLI’S PRINCIPLE AND SUBSONIC AIRFLOW

All of the external aerodynamic forces on a surface are the result of air pressure or air fric- tion. Friction effects are generally confined to a thin layer of air in the immediate vicinity of the surface and friction forces are not the pre- dominating aerodynamic forces. Therefore,

Chapter 1 - BASIC AERODYNAMICS › Figure 1.1. Standard Altitude Table

NAVWEPS OO-ROT-80 BASIC AERODYNAMICS

ICAO STANDARD ATMOSPHERE

*GEOPOTENTIAL OF THE TROPOPAUSE

Figure 1.7. Standard Altitude Table

NAVWEPS 00401-80 BASIC AERODYNAMICS

the pressure forces created on an aerodynamic surface can be studied in a simple form which at first neglects the effect of friction and vis- cosity of the airflow. The most appropriate means of visualizing the effect of airflow and the resulting aerodynamic pressures is to study the fluid flow within a closed tube.

Suppose a stream of air is flowing through the tube shown in figure 1.2. The airflow at station 1 in the tube has a certain velocity, static pressure, and density. As the airstream approaches the constriction at station 2 certain changes must take place. Since the airflow is enclosed within the tube, the mass flow at any point along the tube must be the same and the velocity, pressure, or density must change to accommodate this continuity of flow. BERNOULLI’S EQUATION. A distin- guishing feature of submnic airflow is that changes in pressure and velocity take place with sniall and negligible changes in density. For this reason the study of subsonic airflow can be simplified by neglecting the variation of density in the flow and assuming the flow to be incomprmiblc. Of course, at high flow speeds whjch approach the speed of sound, the flow must be considered as compressible and “compressibility effects” taken into account. However, if the flow through the tube of figure 1.2 is considered subsonic, the density of the airstream is essentially constant at all sta- tions along the length.

If the density of the flow remains constant, static pressure and velocity are the variable quantities. As the flow approaches the con- striction of station 2 the velocity must increase to maintain the same mass flow. As the velocity increases the static pressure will de- crease and the decrease in static pressure which accompanies the increase in velocity can be verified in two ways:

(I) Newton’s laws of motion state the requirement of an unbalanced force to pro- duce an acceleration (velocity change). If the airstream experiences an increase in veloc- ity approaching the constriction, there must

be an unbalance of force to provide the ac- celeration. Since there is only air within the tube, the unbalance of force is provided by the static pressure at station 1 being greater than the static pressure at the constriction, station 2.

(2) The total energy of the air stream in the tube is unchanged. However, the air- .’ stream energy may be in two forms. The airstream may have a potential energy which is related by the static pressure and a kimtic energy by virtue of mass and motion. As the total energy is unchanged, an increase in velocity (kinetic energy) will be accompa- nied by a decrease in static pressure (poten- tial energy). This situation is analagous to a ball rolling along-a smooth surface. As the ball rolls downhill, the potential energy due to position is exchanged for kinetic energy of motion. If .friction- were negli- gibie, the change of potential energy would equal the change in ki,netic energy. This- is also the case for the airflow within the tube. The relationship of static pressure and veloc- ity is maintained throughout the length of the tube. As the flow moves past the constriction toward station 3, the velocity decreases and the static pressure increases.

The Bernoulli equation for incompressible flow is most readily explained ,by accounting for the energy of the~airflow within the tube. As the airstream has no energy added or sub- tracted at any point, the sum of the potential +id kinetic energy must be constant. The kinetic energy of an object is found by:

“KE. =%MV= where K;E. = kinetic energy, ft.-lbs.

M = mass, slugs

V’=velocity, ft./set. The kinetic energy of a cubic foot of air is:

K&x,,

where g= kinetic energy per cu. ft., psf

p=air density, slugs per cu. ft. V=ait velocity, ft./set.

Chapter 1 - BASIC AERODYNAMICS › Figure 1.2. Airflow Within a Tube

NAWEPS DD-BDT-BD BASIC AERODYNAMICS

INCREASEOVELOC

DECREASE0 HEIG

PE + KE = CONSTANT

Ftaure 1.2. Airflow Within a Tube

NAVWEPS 00-ROT-80 BASIC AERODYNAMICS

2500

2000

H=P+q

I

I 1500 I

ci P

d

1000

q

500 I

70K

P=21 16 PSF P = 2014 PSF P = 2133 PSF q= 34 PSF 9 = 136 PSF q= I7 PSF

H- 2150 PSF H = 2150 PSF H = 2150 PSF

Chapter 1 - BASIC AERODYNAMICS › Figure 1.3. Variation of Pressure in Tube

Figure 1.3. Variation o\ Pressure in Tube

If the potential energy is represented by the static pressure, p, the sum of the potential and kinetic energy is the total pressure of the air-

stream.

H=p+% P V’ where H=total pressure, psf (sometimes re- ferred to as “head ’ pressure) p=static pressure, psf. p=density, siugs per cu. ft. V= velocity, ft./set. This equation is the Bernoulli equation for ‘incompressible flow. It is important to ap- preciate that the term >$pV2 has the units of pressure, psf. This term is one of the most important in all aerodynamics and appears so frequently t&it is given the name “dynamic pressure” and the shorthand notation “4”.

q= dynamic pressure, psf

= jgpv2 With this definition it could be said that the sum of static and dynamic pressure in the flow tube remains constant.

Figure 1.3 illustrates the variation of static, dynamic, and total pressure of air flowing through a closed tube. Note that the total pressure is con,stant throughout the length and any change in dynamic pressure produces the same magnitude change in static pressure.

The dynamic pressure of a free airstream is the one ‘common denominator of all aero- dynamic forces and moments. Dynamic pres- sure represents the kinetic energy of the free airstream and is a factor relating the capability for producing changes in static pressure on a

surface. As defined, the dynamic, pressure varies directly as the density and the square of the velocity. Typical values of dynamic pres- sure, 4, are shown in table l-1 for various true airspeeds in the standard atmosphere. Notice that the dynamic pressure at some fixed veloc- ity varies directly with the density ratio at any altitude. Also, appreciate the fact that at an altitude of 40,oM) feet (where the density ratio, b, is 0.2462) it is necessary to have a true air velocity twice that at sea level in order to product the same dynamic pressure.

NAVWEPS 00-801-80 BASIC AERODYNAMICS

TABLE l-l. Effect of Speed and Altitvde on Dwzmnic Prerrure

True air

speed (fr./scc.)

m=

169 338 507 616 845 I, 013

-

,I I

c _-

AIRSPEED MEASUREMENT. If a sym- metrically shaped object were placed in a moving airstream, the flow pattern typical of figure 1.4 would result. The airstream at the very nose of the object would stagnate and the relative flow velocity at this point would be zero. The airflow ahead of the object pos- sesses some certain dynamic pressure and ambient static pressure. At the very nose of the object the local velocity will drop to zero and the airstream dynamic pressure will be converted into an increase in static pressure at the stagnation point. In other words, there will exist a static pressure at the stagnation point which is equal to the airstream total pressure-ambient static pressure plus dynamic pressure.

Around the surface of the object the airflow will divide and the local velocity will increase from zero at the stagnation point to some maximum on the sides of the object. If fric- tion and viscosity effects are neglected, the

Chapter 1 - BASIC AERODYNAMICS › Figure 1.4. Flow Pattern on a Symmetrical Object

NAVWEPS OO-EOT-80 BASIC AERODYNAMICS

FORWARD STAGNATION AFT STAGNATION POINT POINT

AIRSTREAM AHEAD STAGNATION PRESSURE HAS AMBIENT STATIC IS AIRSTREAM TOTAL PRESSURE AND DYNAMIC PRESSURE PRESSURE P+q

Ftgure 1.4. Flow Pattern on a Symmetrical Object

surface anflow continues to the aft stagnation point where the local velocity is again zero. The important point of this example of aero- dynamic flow is existence of the stagnation point. The change in airflow static pressure which takes place at the stagnation point IS equal to the free stream dynamic pressure, q.

The measurement of free stream dynamic pressure is fundamental to the indication of airspeed. In fact, airspeed indicators are sim- ply pressure gauges which measure dynamic pressure related to various airspeeds. Typical airspeed measuring systems are illustrated in figure 1.5. The pitot head has no internal flow velocity and the pressure in the pitot tube is equal to the total pressure of the airstream. The purpose of the static-ports is to sense the true static pressure of the free airstream. The total pressure and static pressure lines are attached to a differential pressure gauge and the net pressure indicated is the dynamic

pressure, q. The pressure gauge is then cali- brated to indicate flight speed in the standard sea level air mass. For example, a dynamic pressure of 305 psf would be realized at a sea

level flight ,speed of 300 knots.

Actually there can be many conditions of flight where the airspeed indicator does not truly reflect the actual velocity through the air mass. The corrections that must be applied are many and lisred in sequence below:

(1) The indicated airspeed (IAS) is the actual instrument indication for some given flight condition. Factors such as an altitude other than standard sea level, errors of the instrument and errors due to the installation, compressibility, etc. may create great vari- ance between this instrument indication and the actual flight speed.

(2) The calibrated airspeed (CM) is the result of correcting IAS for errors of the

NAVWEPS 00-807-80 BASIC AERODYNAMICS

PITOT-STATIC SYSTEM

w / :% . I. q

PITOT WITH SEPARATE

STATIC SOURCE

PRESSURE INDICATED BY GAUGE IS DIFFERENCE BETWEEN TOTAL AND STATIC PRESSURE, H-p= q

Chapter 1 - BASIC AERODYNAMICS › Figure 1.5. Airspeed Measurement

Figure. 1.5. Airspeed Measurement

instrument and errors due to position or lo- cation of the installation. The instrument error must be small by design of the equip- ment and is usually negligible in equjpment which is properly maintained and cared for. The position error of the installation must be small in the range of airspeeds involving critical performance conditions. Position errors are most usually confine,d to the static source in that the actual static pressure sensed at the static port may be different from the free airstream static pressure. When the .,aircraft is operated through a large range’ of angles of attack, the static pressure distribution varies ‘quite greatly and it becomes quite difficult to’minimize the static source error. In most instances a compensating group of static sources may

be combined to reduce the position error. In order to appreciate the magnitude of this problem, at flight speed near 100 knots a

0.05 psi position error is an airspeed error of 10 knots. A typical variation of air- speed system position error is illustrated in figure 1.6.

(3) The equivalent airspeed (PAS) is the result of correcting the (CAS) for compressi- bility effects. At high flight speeds the stagnation pressure recovered in the pitot tube is not representative of the airstream dynamic pressure due to a magnification

by compressibility. Compressibility of the airflow produces a stagnation pressure in the pitot which is greater than if the flow were incompressible. As a result, the air- speed indication is given an erroneous mag- nihcation. The standard airspeed indicator is calibrated to read correct when at standard sea level conditions and thus has a com- pressibility correction appropriate for these conditions. However, when the aircraft is operating above standard sea level altitude,

Revised January 1965

NAVWEPS 00-801-80 BASIC AERODYNAMICS

TYPICAL POSITION ERROR CORRECTION

INDICATED AIRSPEED, KNOTS

COMPRESSIBILITY CORREt

300

CALIBRATED AIRSPEED, KNOTS

Chapter 1 - BASIC AERODYNAMICS › Figure 1.6. Airspeed Corrections

Figure 1.6. Airspeed Corrections (sheet 1 of 2)

NAVWEPS 00-801-80 BASIC AERODYNAMICS

DENSITY ALTITUDE CHART

+g&

‘Id -30fl1111v AlISNxl

Figure 1.6. Airspeed Corrections (sheet 2 of 2)

NAVWEPS 00-SOT-80 BASIC AERODYNAMICS

the inherent compensation is inadequate and additional correction must be applied. The subtractive corrections that must be applied to CA$ depend on pressure altitude and CAS

and are shown on figure 1.6 for the subsonic flight range. The equivalent airspeed (EAS) is the flight speed in the standard sea level air mass which would produce the same free stream dynamic pressure as the actual flight condition.

(4) The true airspeed (TAS) results when the &4X is corrected for density altitude. Since the airspeed indicator is calibrated for the dynamic pressures corresponding to airspeeds at standard sea level conditions, variations in air density must be accounted for. To relate EAS and TAX requires con- sideration that the EAS coupled with stand- .ard sea level density produces the same dy-

namic pressure as the TAX Soupled with the

^^_._^ 1 .:.. 2---:... ,.f *L., bl:A.* rnrJ;r;m.. dCLUd, ‘all UcIIJIcy “I L11L “‘6°C C”IIUACI”L‘. From this reasoning, it can be shown that:

(TAS)2p=(EAS)2 po

d

- or, TAS=EAS 62 P

TAS= EAS 2

4

where TAX= true airspeed

EAS=equivalent airspeed p=actual air density PO= standard sea level air density

n=altitude density ratio, p/pa

The result shows that the TAX is a function of EAS and density altitude. Figure 1.6 shows a chart of density altitude as a function of pressure altitude and temperature. Each par- ticular density altitude fixes the proportion between TAX and EAS. The use of a naviga- tion computer requires setting appropriate values of pressure altitude and temperature on the scales which then fixes rhe proportion be- tween the scales of TAS and EAS (or TAS and CAS when compressibiliry corrections are applicable).

Revlted Jmuoy 1965 14

Thus, the airspeed indicator system measures dynamic pressure and will relate true flight velocity when instrument, position, compress- ibility, and density corrections are applied. These corrections are quite necessary for ac- curate determination of true airspeed and accurate navigation.

Bernoulli’s principle and the concepts of static, dynamic, and total pressure are the basis of aerodynamic fundamentals. The pressure distribution caused by the variation of local stack and dynamic pressures on a surface is the source of the major aerodynamic forces and moment.

DEVELOPMENT OF AERODYNAMIC FORCES

The typical airflow patterns exemplify the relationship of static pressure and velocity defined by Bernoulli. Any object placed in an airstream will have the a& to impact or stag- nate at some point near the leading edge. The pressure at this point of stagnation will be an absolute static pressure equal to the total pres- sure of the airstream. In other words, the static pressure at the stagnation point will be greater than the atmospheric pressure by the amount of the dynamic pressure of the air- stream. As the flow divides and proceeds around. the object, the increases in local ve- locity produce decreases in static pressure. This procedure of flow is best illustrated by the flow patterns and pressure distributions of figure 1.7.

STREAMLINE PATTERN AND PRES- SURE DISTRIBUTION. The flow pattern of the cylinder of figure 1.7 is characterized by the streamlines which denote the local flow direction. Velocity distribution is noted by the streamline pattern since the streamlines effect a boundary of flow, and the airflow between the streamlines is similar to flow in a closed tube. When the streamlines contract and are close together, high local velocities exist; when the streamlines expand and are far apart, low local velocities exist. At the

NAVWEPS 00-8OT-80 BASIC AERODYNAMICS

PEAK SUCTION

PRESSURE

PRESSURE DISTRIBUTION ON A 5v’ )ER

STAGNATION

NEGLECTING FRICTION

(PERFECT FLUID)

CONSIDERING FRICTION EFFECTS

(VISCOUS FLOW)

PRESSURE DISTRIBUTION ON A SYMMETRICAL AIRFOIL AT ZERO LIFT

-PEAK SUCTION

S

AFT STAGNATION POINT

NEGLECTING FRICTION

VISCOUS FLOW

Chapter 1 - BASIC AERODYNAMICS › Figure 1.7. Streamline Pattern and Pressure Distribution

Figure 1.7. Streamline Pattern and Pressure Distribution

NAVWEPS OO-BOT-80 BASIC AERODYNAMICS

forward stagnation point the local velocity is zero and the maximum positive pressure re- sults. As the flow proceeds from the forward stagnation point the velocity increases as shown by the change in streamlines. The local velocities reach a maximum at the upper and lower extremities and a peak suction pres- sure is produced at these points on the cylinder. (NOTE: Positive pressures are pressures above atmospheric and negative or .ruction pressures are less than atmospheric.) As the flow continues aft from the peak suction pressure, the diverging streamlines indicate decreasing local velocities and increasing local pressures. If friction and compressibility effects are not considered, the velocity would decrease to zero

at the aft stagnation point and the full stagna- tion pressure would be recovered. The pressure distribution for the cylinder in perfect fluid flow would be symmetrical and no net force (lift or dragj wvuid rcsuit. Of course, thr relationship between static pressure and ~eloc- ity along the surface is defined by Bernoulli’s equation.

The flow pattern for the cylinder in an actual

fluid demonstrates the effect of friction or viscosity. The viscosity of air produces a thin layer of retarded flow immediately adjacent to the surface. The energy expended in this “boundary layer” can alter the pressure dis- tribution and destroy the symmetry of the pattern. The force unbalance caused by the change in pressure distribution creates a drag force which is in addition to the drag due to

skin friction.

The streamline pattern for the symmetrical airfoil of figure 1.7 again provides the basis for the velocity and pressure distribution. At the leading edge the streamlines are widely diverged in the vicinity of the positive pres- sures. The maximum local velocities and suction (or negative) pressures exist where the streamlines are the closest together, One notable difference between the flow on the cylinder and the airfoil is that the maximum

velocity and minimum pressure points on the

airfoil do not ,necessarily occtir at the point of maximum thickness. However, a similarity does exist in that the minimum pressure points correspond to the points where the streamlines are closest together and this condition exists when the streamlines are forced to the great- est curvature.

GENERATION OF LIFT. An important phenomenon associated with the production of lift by an airfoil is the “circulation” im- parted to the airstream. The best practical illustration of this phenomenon is shown in figure 1.8 by the streamlines and pressure dis- tributions existing on cylinders in an airstream. The cylinder without circulation has a sym- metrical streamline pattern and a pressure dis-

tribution which creates n-0 n_et lift. If the cylinder is given a clockwise rotation and induces a rotational or circulatory flow, a dis- tinct change takes place in the streamline pat- tern and p’ess.~re &str~‘“u~~oii, The vriocitirs due to the vortex of circulatory flow cause increased 104 velocity on the upper surface of the cylinder and decreased local velocity on the lower surface of the cylinder. Also, the circulatory flow produces an upwash immedi- ately ahead and downwash immediately be- hind the cylinder and both fore and aft stagna- tion points are lowered.

The effect of the addition of circulatory flow is appreciated by the change in the pressure distribution on the cylinder. The increased local velocity on the upper surface causes an increase in upper surface suction while the decreased local velocity on the lower surface causes a decrease in lower surface suction. As a result, the cylinder with circulation will produce a net lift. This mechanically induced circulation-called Magnus effect-illustrates the relationship between circulation and lift and is important to golfers, baseball and tennis players as well as pilots and aerodynamicists. The curvature of the flight path of a golf ball or baseball rcluites an unbalance df force which is created by rotation of the ball. The pitcher that can accurately control a .powerful

NAVWEPS 00-8OT-80 BASIC AERODYNAMICS

CYLINDER WITHOUT CIRCULATION

INCREASED LOCAL VELOCITY

UPWASH mSWNWASH

----

\

LDECREASED LOCAL VELOCITY

CYLINDER WITH CIRCULATION

MAGNUS EFFECT BY ROTATING CYLINDER

AIRFOIL LIFT

-ZERO LIFT I

UPWASH

7 INCREASED LOCAL I ,-VELOCITY

POSITIVE LIFT

DECREASED LOCAL VELOCITY

Chapter 1 - BASIC AERODYNAMICS › Figure 1.8. Generation of Lift

Figure 1.8. Generation of Lift (sheet 1 of 2)

NAVWEPS 00-SOT-80 BASIC AERODYNAMICS

Figure 7.8. Generation of Lift (sheet 2 of 2)

NAVWEPS GO-BOT-BO BASIC AERODYNAMlCS

BASIC AIRFOIL SHAPE AND ANGLE OF ATTACK

ORIGINAL ANGLE OF ATTACK

AND DYNAMIC/PRESSURE, 9

ORIGINAL ANGLE OF ATTACK BUT INCREASED DYNAMIC PRESSURE

ORIGINAL ANGLE OF ATTACK AND DYNAMIC PRESSURE BUT ONE-HALF ORIGINAL SIZE

AIRFOIL SHAPE AND ANGLE OF ATTACK DEFINE

RELATIVE PRESSURE DISTRIBUTION

Chapter 1 - BASIC AERODYNAMICS › Figure 1.9. Airfoil Pressure Distribution

Figure 1.9. Airfoil Pressure Distribution

NAVWEPS 00-801-80 BASIC AERODYNAMICS

rotation will be quite a “curve ball artist” the golfer that cannot control the lateral mo- tion of the club face striking the golf ball will impart an uncontrollable spin and have trouble with a “hook” or “slice.” While a rotating cylinder can produce a net lift from the circulatory flow, the method is relatively inefficient and only serves to point out the relationship between lift and circula-, tion. An airfoil is capable of producing lift with relatively high efficiency and the process is illustrated in figure 1.8. If a symmetrical airfoil is placed at zero angle of attack to the airstream, the streamline pattern and pressure distribution give evidence of zero lift. HOW- ever, if the airfoil is given a positive angle of attack, changes occur in the streamline pattern and pressure distribution similar to changes caused by the addition of circulation to the cylinder. The positive angle of attack causes increased velocity on the upper surface with an increase in upper surface suction while the decreased velocity on the lower surface causes a decrease in lower surface suction. Also, upwash is generated ahead of the airfoil, the forward stagnation point moves under the leading edge, and a downwash is evident aft of the airfoil. The pressure distribution 0” the airfoil now provides a net force perpendicu- lar to the airstream-lift.

The generation of lift by an airfoil is depend- ent upon the airfoil being able to create circu- lation in the airstream and develop the lifting, pressure distribution on the surface. In all cases, the generated lift will be the net force caused by the distribution of pressure over the upper and lower surfaces of the airfoil. At low angles of attack, suction pressures usually will exist on both upper and lower surfaces. but the upper surface suction must be greater for positive lift. At high angles of attack near that for maximum lift, a positive pressure will exist on the lower surface but this will account for approximately one-third the net lift.

The effect of free stream density and velocity is a necessary consideration when studying the development of the various aerodynamic forces. Suppose that a particular shape of airfoil is fixed at a particular angle to the airstream. The relative velocity and pressure distribution will be determined by the shape of the airfoil and the angle to the airstream. The effect of varying the airfoil size, air density and air- speed is shown in figure 1.9. If the same air- foil shape is placed at the same angle to an airstream with twice as great a dynamic pres-

sure the magnitude of the pressure distribution will be twice as great but the r&rive shape of the pressure distribution will be the same. With twice as great a pressure existing over the surface, all aerodynamic forces and mo- ments will ~double. If a half-size airfoil ib placed at the same angle to the original air- stream, the magnitude of the pressure distri- bution is the same as the origina! airfoi! and again the relative shape of the pressure dis- tribution is identical. The same pressure act- ing on the half-size surface would reduce all aerodynamic forces to one-half that of the original. This similarity of flow patterns means that the stagnation point occurs at the same place, the peak suction pressure occurs at the same place, and the actual magnitude of the aerodynamic forces and moments depends upon the airstream dynamic pressure and the surface area. This concept is extremely im- portant when attempting to separate and ana- lyze the most important factors affecting the development of aerodynamic forces.

AIRFOIL TERMINOLOGY. Since the shape of an airfoil and the inclination to the airstream are so important in determining the pressure distribution, it is necessary to properly define the airfoil terminology. Figure 1.10 shows a typical airfoil and illustrates the various items of airfoil terminology (1) The chord line is a straight line connect- ing the leading and trailing edges of the airfoil.

Chapter 1 - BASIC AERODYNAMICS › Figure 1.10. Airfoil Terminology

NAVWEPS 00-8DT-80 BASIC AERODYN,AMlCS

LOCAT,ON DF THICKNESS

MAX. THICKNESS UPPER SURFACE

MEAN CAMBER

t CA

CH6RD

-I

t-

v LOCATION OF MAXIMUM CAMBER

RE;L:r;

0 7

LIFT

& 0 G

DRAG

a

Figure 1.10. Airfoil ~erminoh

\

NAVWEPS oOgOT-8O BASIC AERODYNAMICS

(2) The chord is the characteristic dimen- sion of the airfoil.

(3) The mean-camber line is a line drawn halfway between the upper and lower sur- faces. Actually, the chord line connects the ends of the mean-camber line.

(4) The shape of the mean-camber line is very important in determining the aerody- namic characteristics of an airfoil section. The maximum camber (displacement of the mean line from the chord line) and the Ioca- tion of the maximum camber help to define the shape of the mean-camber line. These quantities are expressed as fractions or per- cent of the basic chord dimension. A typi- cal iow speed airfoil may have a maximum camber of 4 percent located 40 percent aft of the leading edge.

(5) The thickness and thickness distribu- tion of the profile are important properties of a section. The maximum tbicknus and location of maximum thickness define thick- ness and distribution of thickness and are expressed as fractions or percent of the chord. A typical low speed airfoil may have a. maximum thickness of 12 percent located 30 percent aft of the leading edge. (6) The leading edge radius of the airfoil is the radius of curvature given the leading edge shape. It is the radius of the circle centered on a line tangent to the leading edge camber and connecting tangency pcints of upper and lower surfaces with the leading edge. Typi- cal leading edge radii are zero (knife edge)

to 1 or 2 percent.

(7) The Iift produced by an airfoil is the net force produced perpendicular to the n&a- tive wind.

(8) The drag incurred by an airfoil is the net force produced parallel to the relative wind.

(9) The angle of attack is the angle between the chord line and the relative wind. Angle of attack is given the shorthand notation a (alpha). Of course, it is important to dif- i ferentiate between pitch attitude angle and

angle of attack. Regardless of the condi- tion of flight, the instantaneous flight path of the surface determines the direction of the oncoming relative wind and the angle of attack is the angle between the instantaneous relative wind and the chord line. To respect the definition of angle of attack, visualize the flight path of the aircraft during a loop and appreciate that the relative wind is defined by the flight path at any point dur- ing the maneuver. Notice that the description of an airfoil profile is by dimensions which are fractions or percent of the basic chord dimension. Thus, when an airfoil. profile is specified a relative shape is described. (NOTB: A numerical sys- tem of designating airfoil profiles originated by the National ~Advisory Committee for Aero- nautics [NACA] is used to describe the main geometric features and certain aerodynamic properties. NACA Report Nol 824 wi!! pro- vide the detail of this system.)

AERODYNAMIC FORCE COEFFICIENT. The aerodynamic forces of lift and drag depend on the combined effect of many different vari- ables. The important single variables could IX:

(1) Airstream velocity (2) Air density (3) Shape or profile of the surface (4) Angle of attack (5) Surface area (6) Compressibility effects (7) Viscosity effects If the effects of viscosity and compressibility are not of immediate importance, the remain- ing items can be combined for consideration. Since the major aerodynamic forces are the result of various pressures distributed on a surface, the surface area will be a major factor. Dynamic prcssurc of the airstream is another common denominator of aerodynamic forces and is a major factor since the magnitude of a pressure distribution depends on the source energy of the free stream. The remaining major factor is the relative peJJ#re dittribution

existing on the surface. Of course, the ve- locity distribution, and resulting pressure dis- tribution, is determmed by the.shape or pro- file of the surface and the angle of a’track. Thus, any aerodynamic force can be repre-

sented as the product df three major factors:

the surface area of the objects the dynamic pressure of the airstream the coefficient or index of force determined

by the relative pressure distribution This relationship is expressed by the following equation :

F= C,qS where

F = aerodynamic force, lbs. C,=coeflicient of aerodynamic force ,iay;mic pressure, psf

S=surface area, sq. ft. In order to fully appreciate the importance of the aerodynamic force coe&cient, C,, the , above equation is rearranged to alternate forms :

In this form, the aerodynamic force coefficient Js appreciared as the aerodynamic force per surface area and dynamic pressure. In other words, the force coefficient is a dimensionless ratio between the average aerodynamic pres- sure (aerodynamic force.per ‘area) and the air- stream dynamic pressure. All the aerodynamic forces of lift and drag are studied on this basis- the common denominator in each case being surface area and dynamic pressure. By such a definition, a “lift coefficient” would .be the ratio between lift pressure and dynamic pres- sure; a “drag coefficient” would be the ratio between drag pressure and.:d.ynamic pressure. The use of the coefficient form of an aero- dynamic force is necessary since the force coellicient is:

(1) An index 04 the aerodynamic force independent of area, density, and velocity.

NAVWEPS m-60T-30 BASIC AERODYNAMICS

It is derived from the relative pressure and velocity distribution.

(2) Influenced only by the shape of the surface and angle of attack since these factors determine the pressure distribution.

(3) An index which allows evaluation of the effects of compressibility and viscosity. Since the effects of area, density, and velocity are obviated by the coefficient form, com- pressibility and viscosity effects can be separated for study. THE BASIC LIFT EQUATION. Lift has been dehned as the net force developed per- pendicular to the relative wind. The aero- dynamic force of lift on an airplane results from the generation of a pressure distribution

on the wing. This lift force is described by the following equation: L=C& where

L=lift, lbs. C, = lift coefficient.

q= dy;:mic pressure, psf +p S= wing surface area, sq. ft. The lift coefhcient used in this equation is the ratio of the lift pressure and dynamic pressure and is a function of the shape of the wing and angle of attack. If the lift coefficient of a conventional airplane wing planfoi-m were plotted versus angle of attack, the result would be typical of the graph of figure 1.11. Since the effects of speed, density, area, weight, alti- tude, etc., are eliminated by the coefficient form, an indication of the true lift capability is ob- tained. Each angle of attack produces a par- ticular lift coefficient since the angle of attack is the controlling factor in the pressure dis- tribution. Lift coeflicient increases with angle of attack up to the maximum lift coefficient, c L,,,~., and, as angle of attack is increased be- yond the maximum lift angle, the airflow is unable to adhere to the upper surface. The airflow then separates from the upper surface and stall occurs.

JNTERPRETATION OF THE LIFT EQUA- TION. Several important relationships are

Chapter 1 - BASIC AERODYNAMICS › Figure 1.11. Typical lift Characteristics

H P

LIFT COEFFICIENT

CL

LIFT PRESSURE

DYNAMIC PRESSURE

L

qs

600

ANGLE OF ATTACK, DEGREES

a

Figure 7.7 1. Typical lib Characteristics

NAVWEPS 00.401-80 BASIC AERODYNAMICS

Thus, a sea level airspeed (or EAS) of 100 knots would provide the dynamic pressure necessary at maximum lift to produce 14,250 Ibs. of lift. If the airplane were operated at a higher weight, a higher dynamic pressure would be required to furnish the greater lift and a higher stall speed would result. If the airplane were placed in a steep turn, the greater lift required in the turn would increase the stall speed. If the airplane were flown at a higher density altitude the TAX at stall would

increase. However, one factor common to each of these conditions is that the angle of attack at C,,,, is the same. It is important to realize that stall warning devices must sense

angle of attack (a) or pressure distribution (related to CL).

Another important fact related by the basic lift equation and lift curve is variation of angle

of attack and lift coefficient with airspeed. Suppose that the example airplane is flown in steady, wing 1eveJ flight at various airspeeds with lift equal to the weight. It is obvious that an increase in airspeed above the stall speed will require a corresponding decrease in lift coeflicient and angle of attack to maintain steady, lift-equal-weight flight. The exact relationship of lift coefficient and airspeed is evolved from the basic lift equation assuming constant lift (equal to weight) and equivaIent airspeeds.

derived from study of the basic lift equation and the typical wing lift curve. One impor- tant fact to be appreciated is that the airplane

shown in figure 1.11 stalls at the same angle of attack regardless of weight, dynamic pres- sure, bank angle, etc. Of course, the stall speed of the aircraft will be affected by weight,

bank angle, and other factors since the product of dynamic pressure, wing area, and lift co- efficient must produce the required lift. A rearrangement of the basic lift equation de- fines this relationship.

L = c&Y

using q =$ (I’ in knots, TAX)

solving for V, - V=17.2 & J L,J

Since the stall speed is the minimum flying speed necessary to sustain flight, the lift co- efficient must be the maximum (CL,,,,).

Suppose that the airplane shown in’ figure 1.11 has the following properties:

Weight = 14,250 lbs

Wing area=280 sq. ft.

C &=1.5

If the airplane is flown in steady, level flight at sea level with lift equal to weight the stall speed would be:

,- V.= 17.24&$

where

V.= stall speed, knots TAS

W= weight, lbs. (lift = weight)

va= 17.2 J (I.&4E;280)

= 100 knots

C‘ v, p -= - C %n.* 0 V

The example airplane was specified to have:

Weight = 14,250 lbs.

C L,,,=lS

V,= 100 knots EAS

The following table depicts the lift coefficients and angles of attack at various airspeeds in steady flight.

NAVWEPS 00-80T-80 BASIC AERODYNAMICS

loo … l.lm 1.30 20.00 110 … ,826 1.24 15.P 17.0 … ,694 1.04 12.7’ lY) … .444 .61 8.20 200 … 230 .38 4.6’ MO … ,111 .I7 2.10 4&l … .c453 .o!J 1.10 30.7 … ,040 .06 .T= 600 … .028 .04 .5O

Note that for the conditions of steady flight, each airspeed requites a specific angle of attack and lift coefficient. This fact provides a fun- damental concept of flying technique: Angle of attack is tbs primary Control of airspeed in steady flight. Of course, the control stick or wheel allows the pilot to control the angle of attack and, thus, control the airspeed in steady flight. In the same sense, the throttle controls the output of the powerplant and allows the pilot to control rate of climb and descent at various airspeeds.

The teal believers of these concepts ate pro- fessional instrument pilots, LSO’s, and glider pilots.. The glider pilot (or flameout enthusi- ast) has no recourse but to control airspeed by angle of attack and accept whatever rate of descent is incurred at the various airspeeds. The LSO must become quite proficient at judg-

ing the flight path and angle of attack of the airplane in the pattern. The more complete visual reference field available to the LSO allows him to judge the angle of attack of the airplane mote accurately than the pilot. When the airplane approaches the LSO, the precise judgment of airspeed is by the angle of attack rather than the rate of closure. If the LSO sees the airplane on the desired flight path but with too low an angle of attack, the

airspeed is too high; if the angle of attack is too high, the airspeed is too low and the ait- plane is approaching the stall. The mirror landing system coupled with an angle of attack indicator is an obvious refinement. The mit- tot indicates the desired flight path and the

NAVWEPS WOT-BO BASIC AERODYNAMICS

angle of attack indicator allows precision con- trol of the airspeed. The accomplished insttu- ment pilot is the devotee of “attitude” flying technique-his creed being “attitude plus power equals performance.” During a GCA approach, the professional instrument pilot controls airspeed with stick (angle of attack) and rate of descent with power adjustment.

Maneuvering flight and certain transient conditions of flight tend to complicate the relationship of angle of attack and airspeed. However, the majority of flight and, certainly, the most critical regime of flight (takeoff, ap- proach, and landing), is conducted in essen- tially steady flight condition.

AIRFOIL LIFT CHARACTERISTICS. Air- foil section properties differ from wing or airplane properties because of the effect of the planform. Actually, the wing may have vati- ous airfoil sections from root to tip with taper, twist, sweepback and local flow components in a spanwise direction. The resulting aeto- dynamic properties of the wing are determined by the action of each section along the span and the three-dimensional flow. Airfoil sec- tion properties are derived from the basic shape or profile in two-dimensional flow and the force coefficients are given a notation of lower case letters. For example, a wing or airplane lift coefficient is C, while an airfoil section lift coefficient is termed cr. Also, wing angle of attack is Q while section angle of attack is differentiated by the use of 01~. The study of

section properties allows an objective consider- ation of the effects of camber, thickness, etc.

The lift characteristics of five illustrative airfoil sections are shown in figure 1.12. The section lift coe&icient, c,, is plotted versus section angle of attack, olO, for five standard NACA airfoil profiles. One characteristic fea- ture of all airfoil sections is that the slope of the various lift curves is essentially the same. At low lift coefhcients, the section lift coeffi- cient increases approximately 0.1 for each degree increase in angle of attack. For each of the airfoils shown, a S’ change in angle of

Chapter 1 - BASIC AERODYNAMICS › Figure 1.12. Lift Characteristics of Typical Airfoil Sections

NAVWEPS OD-8OT-80

BASIC AERODYNAMICS

(DATA FROM NACA REPORT NO. 824)

SECTION ANGLE OF ATTACK

mo, DEGREES

Figure 1.12. Lift Characteristics of lypicol Airfoil Sections

attack would produce an approximate 0.5 change in lift coefficient. Evidently, lift,~curve slope is not a factor important in the selection of an airfoil.

An important lift property affected by the airfoil shape is the section maximum lift co- efficient, ci-. The effect of airfoil shape on ci- can be appreciated by comparison of the lift curves for the five airfoils of figure 1.12. The NACA airfoils 63X06,63-009, and 63i-012 ate symmetrical sections of a basic thickness distribution but maximum thicknesses of 6, 9, and 12 percent respectively. The effect of thickness on ~1% is obvious from an inspec- tion of these curves :

NACA 63-005 .~. :. Cl.82 9.0° NACA 6Mo9. 1.10 10.5~ NACA 63‘-01?,. 1.40 13.80

The 12-percent section has a cr- approxi- mately 70 percent greater than the 6-percent thick section. In addition, the thicker airfoils have greater benefit from the use of various high lift devices.

The effect of camber is illustrated by the lift curves of the NACA 4412 and 631-412 sections. The NACA 4412 section is a 12 percent thick airfoil which has 4 percent maximum camber located at 40 percent of the chord. The NACA 63i-412 airfoil has the same thickness and thickness distribution as the 631-012 but camber added to give a “design”’ lift coefficient (c, for minimum section drag) of 0.4. The lift curves for these two airfoils show that camber has a beneficial e&t on cl-.

ScCdO” %.I a0 for “&*

NACA 6h-312 (symmctricd) :. 1.40 13.e NACA 631-412 Whmd). 1.73 IS. z”

An additional effect of camber is the change in zero lift angle. While the symmetrical

NAVWEPS OO-BOT-BO BASIC AE,RODYMAMlCS

sections have zero lift at zero angle of attack, the sections with positive camber have nega- tive angles for zero lift.

The importance of maximum lift coefficient is obvious. If the maximum lift coefficient is high, the stall speed will be low. However, the high thickness and camber necessary for high section maximum lift coefficients may produce low critical Mach numbers and large twisting moments at high speed. In other words, a high maximum lift coefficient is just one of the many features desired of an airfoil section.

DRAG CHARACTERISTICS. Drag is the net aerodynamic force parallel to the relative

wind and its source is the pressure distribution and skin friction on the surface. Large, thick bluff bodies in an airstream show a predomi- nance of form drag due to the unbalanced pres-

sure distribution. However, streamlined bodies with smooth contours show a ptedomi- nance of drag due to skin friction. In a fashion similar to other aerodynamic forces, drag forces may be considered in the form of a coefficient which is independent of dynamic pressure and surface area. The basic drag equation is as follows:

D=GqS where

D=drag, lbs. C,= drag coefficient

q= dynamic pressure, psf

UP =z (V in knots, TAS)

S= wing surface area, sq. ft. The force of drag is shown as the product of dynamic pressure, surface area, and drag co- efficient, C,. The drag coefficient in this equation is similar to any other aerodynamic force coefficient-it is the ratio of drag pres- sure to dynamic pressure. If the drag co- efficient of a conventional airplane were plotted versus angle of attack, the result would be typical of the graph shown in figure 1.13. At low angles of attack the drag coefficient is low and small changes in angle of attack create only slight changes in drag coefficient. At

Chapter 1 - BASIC AERODYNAMICS › Figure 1.13. Drag Characteristics

NAVWEPS 00-BOT-80 BASIC AERODYNAMICS

I ANGLEOFATTACK,DEGREES

a

Figure 7.73. Drag Characteristics (sheet 1 of 21

CD

ANGLE OF ATTACK, DEGREES

a

Figure 7.13. Brag Characferistics (sheet 2 of 2)

NAVWEPS Oe8OT-80

BASIC AERODYNAMICS

higher angles of attack the drag coefficient is much greater and small changes in angle of

attack cause significant changes in drag. As stall occurs, a large increase in drag takes place.

A factor more important in airplane per- formance considerations is the lift-drag ratio, L/D. With the lift and drag data available for the airplane, the proportions of CL and CD can be calculated for each specific angle of attack. The resulting plot of lift-drag ratio with angle of attack shows that L/D increases to some maximum then decreases at the higher lift coefficients and angles of attack. Note that the maximum lift-drag ratio, (L/D),,,, occurs at one specific angle of attack and lift coefIi- cient. If the airplane is operated in steady flight at (L/D),,,, the total drag is at a mini: mum. Any angle of attack lower or higher than that for (L/D),,, reduces the lift-drag ratio and consequently increases -the total drag for a given airpiane iift.

The airplane depicted by the curves of Figure 1.13 has a maximum lift-drag ratio of 12.5 at an angle of attack of 6”. Suppose this airplane is operated in steady flight at a gross weight of 12,500 lbs. If flown at the airspeed and angle of attack corresponding to (L/D),.., the drag would be 1,000 lbs. Any higher or lower airspeed would produce a drag greater than 1,000 lbs. Of course, this same airplane could be operated at higher or lower gross weights and the same maximum lift-drag ratio of 12.5 could be obtained at the same angle of attack of 6”. However, a change’ in gross weight would require a change in airspeed to support the new weight at the same lift co- efficient and angle of attack.

Type airplane: (L/D) emz

High performance sailplane. 25-40 Typical patrol or transport.. 12-20 High Performance bomber. 2~25 Propeller powered trainer.. 1~15 J et trainer.. 14-16

Transonic fighter or attack.. lo-13

Supersonic fighter or attack. 4-9 (subsonic)

32 Revised Januay 1965

The configuration of an airplane has a great effect on the lift-drag ratio. Typical values of (L/D),.. are listed for various types of airplanes. While the high performance sail- plane may have. extremely high lift-drag ratios, such an aircraft has no real economic or tactical purpose. The supersonic fighter may have seemingly low lift-drag ratios in subsonic flight but the airplane configurations required for supersonic flight (and high [L/D]‘*

at high Mach numbers) precipitate this situa- tion.

Many important items of airplane perform- ance are obtained in flight at (L/D),... Typi- cal performance conditions which occur at (L/D),., are:

maximum endurance of jet powered air-

planes maximum range of propeller driven air-

planes maximum climb angle for jet powered air-

planes maximum power-off glide range, jet or

Prop

The most immediately interesting of these items is the power-off glide range of an air- plane. By examining the forces acting on an airplane during a glide, it can be shown that the glide ratio is numerically equal to the lift-drag ratio. For example, if the airplane in a glide has an (L/D) of 15, each mile of alti- tude is traded for 15 miles of horizontal dis- tance. Such a fact implies that the airplane should be flown at (L/D)- to obtain the greatest glide distance.

An unbelievable feature of gliding perform- ance is the effect of airplane gross weight. Since the maximum lift-drag ratio of a given airplane is an intrinsic property of the aero- dynamic configuration, gross weight will not affect the gliding performance. If a typical jet trainer has an (L/@- of 15, the aircraft 1 can obtain a maximum of 15 miles horizontal

distance for each mile of altitude. This would be true of this particular airplane at any gross

weight if the airplane is flown at the angle of attack for (L/D),. Of course, the gross weight would affect the glide airspeed neces- sary for this particular angle of attack but the glide ratio would be unaffected.

AIRFOIL DRAG CHARACTERISTICS. The total drag of an airplane is composed of the drags of the individual components and the forces caused by interference between these components. The drag of an airplane con- figuration must include the various drags due to lift, form, friction, interference, leakage, etc. To appreciate the factors which affect the drag of an airplane configuration, it is most logical to consider the factors which affect the drag of airfoil sections. In order to allow an objective consideration of the effects of thickness, camber, etc., the properties of two-dimensional sections must be studied. Airfoil section properties are derived from the basic profile in two-dimensional. flow and are provided the lower case shorthand notation to distinguish them from wing or airplane properties, e.g., wing or airplane drag coe5- cient is C, while airfoil section drag coefficient is c,.

The drag characteristics of three illustrative airfoil sections are shown in figure 1.14. The section drag coe&cient, c,, is plotted versus the section lift coefficient, cr. The drag on the airfoil section is composed of pressure drag and skin friction. When the airfoil is at low lift coe&cients, the drag due to skin friction predominates. The drag curve for a conven- tional airfoil tends to be quite shallow in this region since there is very little variation of skin friction with angle of attack. When the airfoil is at high lift coefficients, form or pressure drag predominates and the drag co- efficient varies rapidly with lift coefficient. The NACA 0006 is a thin symmetrical profile which has a maximum thickness of 6 percent located at 30 percent of the chord. This section shows a typical variation of cd and cr.

The NACA 4412 section is a 12 percent thick airfoil with 4 percent maximum camber at

NAVWEPS OO-EOT-RO BASIC AERODYNAMICS

40 percent chord. When this section is com- pared with the NACA 0006 section the effect of camber can be appreciated. At low lift coefficients the thtn, symmetrical section has much lower drag. However, at lift coeffi- cients above 03 the thicker, cambered section has the lower drag. Thus, proper camber and thickness can improve the lift-drag ratio of the section.

The NACA 63,412 is a cambered 12 percent thick airfoil of the ‘“laminar flow” type. This airfoil is shaped to produce a design lift coe5cient of 0.4. Notice that the drag curve of this airfoil has distinct aberrations with very low drag coefficients near the lift coeffi- cient of 0.4. This airfoil profile has its camber and thickness distributed to produce very low uniform velocity on the forward surface (mini- mum pressure point well aft) at this lift coeffi- cient. The resulting pressure and velocity distribution enhance extensive laminar flow in the boundary layer and greatly reduce the skin friction drag. The benefit of the laminar flow is appreciated by comparing the minimum drag of this airfoil with an airfoil which has one-half the maximum thickness-the NACA ooo6.

The choice of an airfoil section will depend on the consideration oftmany different factors. While the cI, of the section is an important quality, a more appropriate factor for con- sideration is the maximum lift coefficient of the section when various high lift devices are applied. Trailing edge flaps and leading edge high lift devices are applied to increase the

cr,, for low speed performance. Thus, an appropriate factor for comparison is the ratio of section drag coe5cient to section maximum lift coefficient with flaps-cd/crm,. When this quantity is corrected for compressibility, a preliminary selection of an airfoil section is possible. The airfoil having the lowest value of c&~, at the design flight condition (en- durance, range, high speed, etc.) will create the least section drag for a given .design stall speed.

NAVWEPS DD-BOT-BD BASK AERODYNAMICS

(DATA FROM NACA REPORT ~0.824)

SMOOTH SURFAC

e-L-- -.2 Cl .2 .4 .6 .8 LO’---I.2 1.4 1.6 1.8

SECTION LIFT COEFFICIENT

Cl

Chapter 1 - BASIC AERODYNAMICS › Figure 1.14. Drag Characteristics of Typical Airfoil Sections

Figure 1.14. Drag Characteristics of Typical Airfoil Sections

PLIGHT AT HIGH LIFT CONDITIONS

It is frequently stated that the career Naval Aviator spends more than half his life “below a thousand feet and a hundred knots.” Re- gardless of the implications of such a state- ment, the thought does cunnute the relation- ship of minimum flying speeds and carrier aviation. Only in Naval Aviation is there such importance assigned to precision control of the aircraft at high lift conditions. Safe operation in carrier aviation demands precision control of the airplane at high lift conditions.

The aerodynamic lift characteristics of an airplane are portrayed by the curve of lift coefficient versus angle of attack. Such a curve is illustrated in figure 1.15 for a specific airplane in the clean and flap down configura- tions. A given aerodynamic configuration ex- periences increases in lift coefficient with in- creases in angle of attack until the maximum lift coefficient is obtained. A further increase in angIe of attack produces stall and the lift coefficient then decreases. Since the maximum lift coefficient corresponds to the minimum speed available in flight, it is an important point of reference. The stall speed of the air- craft in level flight is related by the equation:

V7.=17.2

J--

c w

.ln2s where

V.-stall speed, knots TAS W=gross weight, lbs. c Lnoz= airplane maximum lift coefficient

csaltitude density ratio S= wing area, sq. ft.

This equation illustrates the effect on stall speed of weight and wing area (or wing load- ing, W/S), maximum lift coefficient, and alti- tude. If the stall speed is desired in EAS, the density ratio will be that for sea level (u= 1.000). EFFECT OF WEIGHT. Modern configu- rations of airplanes are characterized by a large percent. of the maximum gross weight being

NAVWEPS 00-BOT-RO BASIC AERODYNAMICS

fuel. Hence, the gross weight and stall speed of the airplane can vary considerably through- out the flight. The effect of only weight on stall speed can be expressed by a modified form of the stall speed equation where density ratio, c r,,,.,, and wing area are held constant.

V _i_z- K J v.,- K where

V*,=stall speed corresponding to some gross weight, WI V@a= stall speed corresponding to a dif-

ferent gross weight, WP

As an illustration of this equation, assume that a particular airplane has a stall speed of 100 knots at a gross weight of 10,000 lbs. The stall speeds of this Sam: airplane at other gross weights would be:

ll,W 100x 4, ‘&~=lO,

12,ooO 110 14,4al 120 9mJ 95 8,100 90

Figure 1.15 illustrates the effect of weight on

stall speed on a percentage basis and will be valid for any airplane. Many specific condi- tions of flight are accomplished at certain fixed angles of attack and lift coefficients. The effect of weight on a percentage basis on the speeds for any specific lift coefficient and angle of attack is identical. Note that at small variations of weight, a rule of thumb may express the effect of weight on stall speed- “a 2 percent change in weight causes a I per- cent change in stall speed.”

EFFECT OF MANEUVERING FLIGHT. Turning flight and maneuvers produce an effect on stall speed which is similar to the effect of weight. Inspection of the chart on figure 1.16 shows the forces acting on an airplane in a steady turn. Any steady turn requires that the vertical component of Iift be equal to

NAVWEPS OD-SOT-80 BASIC AERODYNAMICS

EFFECT OF FLAPS

CL LIFT COEFFICIENT

I

5 IO I5 20 25

ANGLE OtATTACK

EFFECT OF WEIGHT ON STALL SPEED

Chapter 1 - BASIC AERODYNAMICS › Figure 1.15. Flight at High Lift Conditions

Figure 1.15. Flight at High Lift Conditions

NAVWEPS 00-8OT-80 BASIC AERODYNAMICS

EFFECT OF HIGH LIET DEVICES. The primary purpose of high lift devices (flaps, slots, slats, etc.) is to increase the CLn, of the airplane and reduce the stall speed. The take- off and landing speeds are consequently re- duced. The effect of a typical high lift device is shown by the airplane lift curves of figure

1.15 and is summarized here:

weight of the airplane and the horizontal com- ponent of lift be equal to the centrifugal force. Thus, the aircraft in a steady turn develops a lift greater than weight and experiences in- creased stall speeds.

Trigonometric ‘relationships allow deter- mination of the effect of bank angle on stall

speed and load factor. The load factor, B, is the proportion between lift and weight and is determined by:

L fizz-- W

1 n=-

cos I$

where

n=load factor (or “G”) cos 6 = cosine of the bank angle, + (phi)

Typical values of load factor determined by this relationship are:

.+.- 00 130 300 450 600 759

n-l.00 1.035 1.154 1.414 z.ooo 4.ooo

The stall speed in a turn can be determined by:

where

v,+= stall speed at some bank angle +

V,= stall speed for wing level, lift-equal-

weight flight n=load factor corresponding to the bank angle

The percent increase in stall speed in a turn is shown on figure l.i6. Since this chart is predi- cated on a steady turn and constant CL,, the figures a!e valid for any airplane. The chart shows that no appreciable change in load fac- tor or stall speed occurs at bank angles less than 30“. Above 4S” of bank the increase in load factor and stall speed is quite rapid. This fact emphasizes the need for avoiding steep turns at low airspeeds-a flight condition common to stall-spin accidents.

c.mip~tion L. (II far C‘,

clun(tla~Up) … … 1.5 200 Php down. 2.0 IS.9

The principal effect of the extension of flaps is to increase the C,, and reduce the angle of attack for any given lift coefficient. The in- crease in CL,, afforded by flap deflection re- duces the stall speed in a certain proportion, the effect described by the equation:

- v,=v, z% J Ch,

where

V,,= stall speed with flaps down

v,=stall speed without flaps

C,= maximum lift coefficient of

the clean configuration

C&,= maximum lift coefficient

with flaps down

For example, assume the airplane described by the lift curves of figure 1.15 has a stall speed of 100 knots at the landing weight in the clean configuration. If the flaps are lowered the reduced stall speed is reduced to:

=86.5 knots

Chapter 1 - BASIC AERODYNAMICS › Figure 1.16. Flight at High Lift Conditions

NAVWWS 00-8OT-80 BASIC AERODYNAMICS

.#a, GANK~ANGLE, DEGREES

EFFECT OF c

LMAX

ONSTALL SPEED

250

200 ANT

150 %

100

50

IO 20 30 40 50

PERCENTDECREASE

IN STALL SPEED

Figure 7.76. Flight at High Liff Conditions

Revised Jarwary 1965

Thus, wirh rhe higher lift coefficienr available, less dynamic pressure is required to provide the necessary lift.

Because of the stated variation of stall speed with C-, large changes in CL- are necessary to produce significant changes in stall speed. This effect is illustrated by the graph in figure 1.16 and certain typical values are shown below:

Percent increase in CL. .~. 2 10 so loo 300

Percent reduction in stall speed 1 5 18 29 50

The contribution of the high lift devices must be considerable to cause large reduction in stall speed. The most elaborate combination of flaps, slots, slats, and boundary layer con- trol throughout the span of the wing would be required to increase C,- by 300 percent. A common case is that of a typical propeller driven transport which experiences a 70 per- cent increase in CzIM1 by full flap deflection. A typical single engine jet fighter with a thin swept wing obtains a 20 percent increase in CL- by full flap deflection. Thin airfoil sec- tions with sweepback impose distinct limita- tions on the effectiveness of flaps and the 20 percent increase in CL- by flaps is a typical- if not high-value for such a configuration. One factor common to maximum lift condi- tion is the angle of attack and pressure distri- bution. The maximum lift coefficient of a particular wing configuration is obtained at one angle of attack and one pressure distribu- tion. Weight, bank angle, load factor, density altitude, and airspeed have no direct effect on the stall angle of attack. This fact is sufficient justification for the use of angle of attack indi- cators and stall warning devices which sense pressure distribution on the wing. During flight maneuvers, landing approach, takeoff, turns, etc. the airplani will stall if the critical angle of attack is cxcccdcd. The airspeed ar which stall occurs will be determined by weight, load factor, and altitude but the stall

NAVWEPS OO-EOT-RO BASIC AERODYNAMICS

angle of attack is unaffected. At any parricu- lar altitude, the indicated stall speed is a func- tion of weight and load factor. An increase in altitude will produce a decrease in density and increase the true airspeed at stall. Also, an increase in altitude will alter compressibility and viscosity effects and, generally speaking, cause the in,&ztcd stall speed to increase. This parti&lar consideration is usually sig- nificant only above altitudes of 20,000 ft.

Recovery from stall involves a very simple concept. Since stall is precipitated by an excessive angle of attack, the angle of attack must be dccmmd. This is a fundamental princi- ple which is common to any airplane.

An airplane may be designed to be “stall- proof” simply by reducing the effectiveness of the elevators. If the elevators are not power- ful enough to hold the airplane to high angles of attack, the airplane cannot be stalled in any condition of flight. Such a requirement for a tactical military airplane would seriously re- duce performance. High lift coefficients near the maximum are required for high maneuver- ability and low landing and takeoff speeds. Hence, the Naval Aviator must appreciate the effect of the many variables affecting the stall speed and regard “attitude flying,” angle of attack indicators, and stall warning devices as techniques which allow more precise control of the airplane at high lift conditions.

HIGH LIFT DEVICES

There are many different types of high lift devices used to increase the maximum lift co- efficient for low speed flight. The high lift devices applied to the trailing edge of a section consist of a flap which is usually 15 to 25 per- cent of the chord. The deflection of a flap produces the effect of a large amount of camber added well aft on the chord. The principal types of flaps are shown applied to a basic sec- tion of airfoil. The effect of a 30’ deflection of a 25 percent chord flap is shown on the lift and drag curves of figure 1.17.

NAVWEPS 00-BOT-80 BASIC AERODYNAMICS

BASIC SECTION

PLAIN FLAP SPLIT FLAP

SLOTTED FLAP FOWLER FLAP

EFFECT ON SECTION-LIFT AND DRAG CHARACTERISTICS OF A 25% CHORD FLAP DEFLECTED 30°

I SLOTTED

3.0 -

2.5 -

2.0 -

1.5 -

I.O-

.5 -

0 -I- O

FOW&ER

SECTION ANGLE OF ATTACK SECTION DRAG COEFFICIENT

o,,, DEGREES cd

Chapter 1 - BASIC AERODYNAMICS › Figure 1.17. Flap Configurations

Figure 1.17. Flap Configurations

Revised January 1965

The plainjap shown in figure 1.17 is a simple hinged portion of the trailing edge. The effect of the camber added well aft on the chord causes a significant increase in cbr. In addi- tion, the zero lift angle changes to a more negative value and the drag increases greatly. The split flap shown in figure 1.17 consist of plate deflected from the lower surface of the section and produces a slightly greater change in c ImoT than the plain flap. However, a much larger change in drag results from the great turbulent wake produced by this type flap. The greater drag’may not be such a disadvan- rage when ir is realized that it may be advan- tageous to accomplish steeper landing ap- proaches over obstacles or require higher power from the engine during approach (to minimize engine acceleration time for waveoR).

The slottedPap is similar to the plain flap but the gap between the main section and flap leading edge is given specific contours. High energy air from the lower surface is ducted to the flap upper surface. The high energy air from the slot accelerates the upper surface

boundary layer and delays airflow separation to some higher lift coefficient. The slotted flap can cause much greater increases in c,,, than the plain or split flap and section drags are much lower.

The Fowkr&zp arrangement is similar to the slotted flap. The difference is that the de- flected flap segment is moved aft along a set of tracks which increases the chord and effects an increase in wing area. The Fowler flap is characterized by large increases in c,,, with minimum changes in drag. ,.

One additional factor requiring consider- ation in a comparison of flap types is the aero- dynamic twisting moments caused by the flap. Positive camber produces a nose down twisting moment-especially great when large camber is used well aft on the chord (an obvious implication is that flaps are not prac- tical on a flying wing or tailless airplane). The deflection of a flap causes large nose down moments which create important twisting

NAVWEPS OO-BOT-BO BASIC AERODYNAMICS

loads on the structure and pitching moments that must be controlled with the horizontal tail. Unfortunately, the flap types producing the greatest increases in c,,- usually cause the greatest twisting moments. The Fowler flap causes the greatest change in twisting moment while the split flap causes the least. This factor-along with mechanical complexity of the installation-may complicate the choice of a flap configuration.

The effectiveness of flaps on a wing con- figuration depend on many different factors. One important factor is the amount of the wing area affected by the flaps. Since a certain amount of the span is reserved for ailerons, the actual wing maximum lift prop- erties will be less than that of the flapped two-dimensional section. If the basic wing has a low thickness, any type of flap will be less effective than on a wing of greater thick- ness. Sweepback of the wing can cause an additional significant reduction in the effec- tiveness of flaps.

High lift devices applied to the leading edge of a section consist of slots, slats, and small

amounts of local camber. The fixed slot in a wing conducts flow of high energy air into the boundary layer on the upper surface and delays airflow separation to some higher angle of attack and lift coefficient. Since the slot alone effects no change in camber, the higher maximum lift coefficient will be obtained at a higher angle of attack, i.e., the slot simply delays stall to a higher angle of attack. An automatic slot arrangement consists of a leading edge segment (slat) which is free to move on tracks. At low angles of attack the slat is held flush against the leading edge by the high positive local pressures. When the section is at high angles of attack, the high local suction pressures at the leading edge create a chordwise force forward to actuate the slat. The slot formed then allows the section to continue to a higher angle of attack and produce a clno. greater than that of the

Chapter 1 - BASIC AERODYNAMICS › Figure 1.18. Effect of Slots and Boundary Layer Control

NAVWEPS CO-BOT-BO BASIC AERODYNAMICS

AUTOMATIC SLOT

BOUNDARYLAYERCONTROL BY UPPER SURFACE SUCTION

BOUNDARY LAYER CONTROL

BY FLAP AUGMENTATION

0 2.4 FIXED SLOT\ I

LOW SUCTION

,BASIC SECTION

NO SUCTION

0-l 0~ : -5 0 5 IO I5 20 0 5 IO I5 20 25

SECTION ANGLE OF ATTACK SECTION ANGLE OF ATTACK 00, DEGREES 00, DEGREES

Figure 7.18. Ekt of Slots and Boundary Layer Control

basic section. The effect of a fixed slot on the lift characteristics is shown in figure 1.18.

.UO~J ana’ &Z~J can produce significant in- creases in cl, but the increased angle of attack for maximum lift can be a disadvantage. If slots were the only high lift device on the wing, the high take off and landing angles of attack may complicate the design of the landing gear. For this reason slots or slats are usually used in conjunction with flaps since the flaps provide reduction in the maxi- mum lift angle of attack. The use of a slot has two important advantages: there is only a negligible change in the pitching moment due to the slot and no significant change in section drag at low angles of attack. In fact, the slotted section will have less drag than the basic section near the maximum lift angle for the basic section.

The slot-slat device finds great application in modern airplane configurations. The tail- less airplane configuration can utilize only the high lift devices which have negligible effect on the pitching moments. The slot and slat are often used to increase the cl- in high speed flight when compressibility effects are con- siderable. The small change in twisting mo- ment is a favorable feature for any high lift device to be used at high speed. Leading edge high lift devices are more effective on the highiy swept wing than trailing edge flaps since slats are quite powerful in controlling the flow pattern. Small amounts of local camber added to the leading edge as a high lift device is most effective on wings of very low thick- ness and sharp leading edges. Most usually

the slope of the leading edge high lift device is used to control the spanwise lift distribution on the wing.

‘Boundary larcr control devices are additional means of increasing the maximum lift coe&- cient of a section. The thin layer of airflow adjacent to the surface of an airfoil shows re- duced local velocities from the effect of skin friction. When at high angles of attack this boundary layer on the upper surface tends to

NAVWEPS OO-BOT-RO BASIC AERODYNAMICS

stagnate and come to a stop. If this happens the airflow will separate from the surface and stall occurs. Boundary layer control for high lift applications features various devices to maintain high velocity in the boundary layer to allay separation of the airflow. This con- trol of the boundary layer kinetic energy can be accomplished in two ways. One method is the application of a suction through ports to draw off low energy boundary layer and replace it with high velocity air from outside the boundary layer. The effect of surface suction boundary layer control on lift characteristics is typified by figure 1.18. Increasing surface suction produces greater maximum lift coe5- cients which occur at higher angles of attack. The effect is similar to that of a slot because the slot is essentially a boundary layer control device ducting high energy air to the upper surface.

Another method of boundary layer control is accomplished by injecting a high speed jet of air into the boundary layer. This method produces essentially the same results as the suction method and is the more practical in- stallation. The suction type BLC requires the installation of a separate pump while the “blown” BLC system can utilize the high pres- sure source of a jet engine compressor. The typical installation of a high pressure BU system would be the augmentation of a de- flected flap. Since any boundary layer control tends to increase the angle of attack for maxi- mum lift, it is important to combine the bound- ary layer control with flaps since the flap de- flection tends to reduce the angIe of attack for maximum lift

OPERATION OF HIGH LIFT DEVICES. The management of the high lift devices on an airplane is an important factor in flying opera- tions. The devices which are actuated auto- matically-such as automatic slats and slots- are usually of little concern and cause little complication since relatively small changes in drag and pitching moments take place. How- ever, the flaps must be properly managed by the pilot to take advantage of the capability

2.5

2.0

CL 1.5 LIFT COEFFICIENT 1.0 4

.5

0 -10 -5 0

FLAP RETRACTION

FLAPS DOWN

CLEAN CONFIGURATION

FLAP EXTENSION

5 10 15 20 25

ANGLE OF ATTACK α, DEGREES

BASIC AERODYNAMICS NAVWEPS 00-80T-80

2.5

FLAP RETRACTION 2.0

1.5 CONFIGURATION CLEAN

CL. 1.0

FLAPS DOWN

.5 FLAPEXTENSION

0 0 0.10 0.20 0.30

DRAG COEFFICIENT Co

Chapter 1 - BASIC AERODYNAMICS › Figure 1.19. Effect of Flaps on Airplane Characteristics

Figure 1.19. Effect of Flaps on Airplane Characteristics

of such a device. To illustrate a few principles of flap management, figure 1.19 presents the lift and drag curves of a typical airplane in the

clean and flap down configurations.

In order to appreciate some of the factors involved in flap management, assume that the airpIane has just taken off and the flaps are extended. The pilot should not completely retract the flaps until the airplane has sufficient speed. If the flaps are retracted prematurely at insufhcient airspeed, maximum lift coefi- cient of the clean configuration may not be able to support the airplane and the airplane will sink or stall. Of course, this same factor must be considered for intermediate flap posi- tions between fully retracted and fully ex- tended. Assume that the airplane is allowed to gain speed and reduce the flight lift coefii- cient to the point of flap retraction indicated on figure 1.19. As the configuration is altered from the “cluttered” to the clean configura- tion, three important changes take place: (1) The reduction in camber by flap re- traction changes the wing pitching moment and-for the majority of airplanes-requires retrimming to balance the nose up moment change. Some airplanes feature an automat-

ic retrimming which is programmed with flap deflection.

(2) The retraction of flaps shown on figure 1.19 causes a reduction of drag coeffi- cient at that lift coefficient. This drag reduction improves the acceleration of the airplane.

(3) The retraction of flaps requires an increase in angle of attack to maintain the same lift coefficient. Thus, if airplane accel- eration is low through the flap retraction speed range, angle of attack must be in- creased to prevent the airplane from sinking. This situation is typical after takeoff when gross weight, density altitude, and tempera- ture are high. However, some aircraft have such high acceleration through the flap re- traction speed that the rapid gain in air- speed requtres much less noticeable attitude change.

NAVWEPS OO-EOT-SO BASIC AERODYNAMICS

When the flaps are lowered for landing essen- tially the same items must be considered. Ex- tending the flaps will cause these. changes to take place:

(1) Lowering the flaps requires retrim- ming to balance the nose down moment change.

(2) The increase in drag requires a higher power setting to maintain airspeed and altitude.

(3) The angle of attack required to pro- duce the same lift coefficient is less, e.g., flap extension tends to cause the airplane to

“balloon.” An additional factor which must be consid- ered when rapidly accelerating after takeoff, or when lowering the flaps for landing, is the limit airspeed for flap extension. Excessive airspeeds in the flap down configuration may cause structural damage.

In many aircraft the effect of intermediate flap deflection is of primary importance in certain critical operating conditions. Small initial deflections of the flap cause noticeable changes in C’s,, without large changes in drag coefficient. This feature is especially true of the airplane equipped with slotted or Fowler flaps (refer to fig. 1.17). Large flap deflections past 30’ to 33’ do not create the same rate of change of Cs- but do cause greater changes in CD. A fact true of most airplanes is that the first 50 percent of flap deflection causes mwc than half of the total change in Cr.- and the last 50 percent of flap deflection causes mo~c than half of the total change in Cs.

Continue reading ↓ 120 of 1050 passages shown