Radar Vectors
Proposed Rule Proposed Issued Feb 12, 2009 5 pages Copy saved Nov 17, 2026

74 FR 7006 Airworthiness Directives; M7 Aerospace LP Models SA226-AT, SA226-T, SA226-TC, SA227-AC (C-26A), SA227-AT, SA227-BC (C-26A), SA227-CC, and SA227-DC (C-26B) Airplanes

We propose to supersede Airworthiness Directive (AD) 2008-12-16, which applies to certain M7 Aerospace LP SA226 and SA227 series airplanes. AD 2008-12-16 currently requires you to inspect wires and tube assemblies for chafing, arcing, or insufficient clearance between components. If chafing, arcing, or insufficient clearance between components is found, AD 2008-12-16 requires you to clear, repair, and/ or replace all chafed wires, components, and tube assemblies. AD 2008-12-16 also requires you to cover the four-gauge wires leaving the battery box with firesleeving and secure them with a clamp. Since we issued AD 2008-12-16, M7 Aerospace LP has notified us that Model SA227-BC (C-26A) was inadvertently left out of the Applicability section of the AD and they updated some of the service information due to parts availability. Operators have also identified issues with model applicability that needed clarification. Consequently, this proposed AD would retain the actions of AD 2008-12-16, add Model SA227-BC (C-26A) to the Applicability section, and regroup the models for clarification. We are proposing this AD to detect and correct chafing of electrical wires, components, and tube assemblies. This condition could result in arcing of exposed wires with consequent burning of a hole in a hydraulic line or the bleed air line. This failure could lead to a hydraulic fluid leak and a possible fire in the engine nacelle compartment.

This document is proposed. It may have been replaced. Check the official source before relying on it.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2009-0119; Directorate Identifier 2008-CE-068-AD] RIN 2120-AA64

Airworthiness Directives; M7 Aerospace LP Models SA226-AT, SA226-T, SA226-TC, SA227-AC (C-26A), SA227-AT, SA227-BC (C-26A), SA227-CC, and SA227-DC (C-26B) Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of Transportation (DOT).

Action

ACTION: Notice of proposed rulemaking (NPRM).

SUMMARY: We propose to supersede Airworthiness Directive (AD) 2008-12-16, which applies to certain M7 Aerospace LP SA226 and SA227 series airplanes. AD 2008-12-16 currently requires you to inspect wires and tube assemblies for chafing, arcing, or insufficient clearance between components. If chafing, arcing, or insufficient clearance between components is found, AD 2008-12-16 requires you to clear, repair, and/ or replace all chafed wires, components, and tube assemblies. AD 2008-12-16 also requires you to cover the four-gauge wires leaving the battery box with firesleeving and secure them with a clamp. Since we issued AD 2008-12-16, M7 Aerospace LP has notified us that Model SA227-BC (C-26A) was inadvertently left out of the Applicability section of the AD and they updated some of the service information due to parts availability. Operators have also identified issues with model applicability that needed clarification. Consequently, this proposed AD would retain the actions of AD 2008-12-16, add Model SA227-BC (C-26A) to the Applicability section, and regroup the models for clarification. We are proposing this AD to detect and correct chafing of electrical wires, components, and tube assemblies. This condition could result in arcing of exposed wires with consequent burning of a hole in a hydraulic line or the bleed air line. This failure could lead to a hydraulic fluid leak and a possible fire in the engine nacelle compartment.

Dates

DATES: We must receive comments on this proposed AD by April 13, 2009.

ADDRESSES: Use one of the following addresses to comment on this proposed AD:

• Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.

• Fax: (202) 493-2251.

Addresses

• Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590.

• Hand Delivery: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this proposed AD, contact M7 Aerospace Repair Station, 10823 NE Entrance Road, San Antonio, Texas 78216; telephone: (210) 824-9421; fax: (210) 804-7766; Internet: http://www.m7aerospace.com.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Werner Koch, Aerospace Engineer, ASW-150, Fort Worth Airplane Certification Office, 2601 Meacham Blvd., Fort Worth, Texas 76137; telephone: (817) 222-5133; fax: (817) 222-5960.

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to send any written relevant data, views, or arguments regarding this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include the docket number, "FAA-2009-0119; Directorate Identifier 2008-CE-068-AD" at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the proposed AD. We will consider all comments received by the closing date and may amend the proposed AD in light of those comments.

Comments Invited

We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive concerning this proposed AD.

Discussion

Five reports of chafing between the bleed air tube assembly and the electrical starter cables on M7 Aerospace LP SA226 and SA227 series airplanes, with one incident resulting in a fire, caused us to issue AD 2008-12-16, Amendment 39-15560 (73 FR 34615, June 18, 2008). AD 2008-12-16 currently requires the following on M7 Aerospace LP SA226 and SA227 series airplanes:

Discussion

• Inspect electrical wires and components, hydraulic tube assemblies, and bleed air tube assemblies, for sufficient clearance between components or any evidence of chafing or arcing;

• Clear, repair, and/or replace all chafed electrical wires and components, chafed hydraulic tube assemblies, and chafed bleed air tube assemblies; and

• Cover the four-gauge wires leaving the battery box with firesleeving and secure them with a clamp.

Since we issued AD 2008-12-16, M7 Aerospace LP has notified us that Model SA227-BC (C-26A) was inadvertently left out of the Applicability section of the AD and they updated some of the service information due to parts availability. Operators have also identified issues with the model applicability that needed clarification. Consequently, this proposed AD would retain the actions of AD 2008-12-16, add the Model SA227-BC (C-26A) to the Applicability section, and regroup the models for clarification. We are proposing this AD to detect and correct chafing of electrical wires, components, and tube assemblies.

This condition could result in arcing of the exposed wires with consequent burning of a hole in a hydraulic line or the bleed air line. This failure could lead to a hydraulic fluid leak and a possible fire in the engine nacelle compartment.

Relevant Service Information

We have reviewed the following service bulletins and procedures:

Relevant Service Information

Service bulletin Applicable models Procedures described

Fairchild Aircraft Corporation SA226 Series SA226-AT, SA226-T, and SA226-TC. Inspecting the battery cables

Service Bulletin 226-24-019, revised: and covering the four-gauge

November 21, 2008. wires leaving the battery box

with firesleeving and securing

them with a clamp.

Fairchild Aircraft Corporation SA227 Series SA227-AC, SA227-AT, and SA227-BC

Service Bulletin No. SB227-24-001, revised: (C-26A).

November 21, 2008.

M7 Aerospace SA226 Series Service Bulletin SA226-AT and SA226-TC … Rerouting the hydraulic tube

No. 226-24-020, revised: August 4, 2008. assemblies in the right wing

leading edge, rerouting the

battery cables and 22-gauge

wire bundle, and installing a

new access panel forward of

the battery box.

M7 Aerospace SA227 Series Service Bulletin SA227-AC and SA227-AT …

No. 227-24-002, revised: November 21, 2008.

M7 Aerospace SA226 Series Service Bulletin SA226AT, SA226-T, and SA226TC... Inspecting electrical wires and

No. 226-24-036, revised: November 21, 2008. components, hydraulic tube

assemblies, and bleed air tube

assemblies at the inboard wing

leading edge/battery box

areas, wing stations 51.167 to

81.174, and the feed-through

locations into the inboard

keelson.

M7 Aerospace SA227 Series Service Bulletin SA227-AC (C-26A), SA227-BC (C-

No. 227-24-019, revised: November 21, 2008. 26A), and SA227-AT.

M7 Aerospace SA227 Series Commuter Category SA227-CC and SA227-DC (C-26B)...

Service Bulletin No. CC7-24-010, revised: November 21, 2008.

FAA's Determination and Requirements of the Proposed AD

FAA's Determination and Requirements of the Proposed AD

We are proposing this AD because we evaluated all information and determined the unsafe condition described previously is likely to exist or develop on other products of the same type design. This proposed AD would supersede AD 2008-12-16 with a new AD that would retain the actions of AD 2008-12-16, add Model SA227-BC (C26A) to the Applicability section, and regroup the models for clarification. We are proposing this AD to detect and correct chafing of electrical wires, components, and tube assemblies. This proposed AD would require you to use the service information described previously to perform these actions.

Costs of Compliance

Costs of Compliance

We estimate that this proposed AD would affect 268 airplanes in the U.S. registry.

We estimate the following costs to do the proposed inspection:

Total cost per Total cost on

Labor cost Parts cost airplane U.S. operators

4 work-hours x $80 per hour = $320 … Not Applicable … $320 $85,760

We estimate the following costs to do any necessary modifications for certain Models SA226-AT, SA226-T, SA226-TC, SA227-AC, and SA227-AT airplanes referenced in M7 Aerospace SA226 Series Service Bulletin 226-24-019, revised: November 21, 2008; or M7 Aerospace SA227 Series Service Bulletin 227-24-001, revised: November 21, 2008. We estimate 88 airplanes may need this modification:

Total cost per Total cost on

Labor cost Parts cost airplane U.S. operators

13 work-hours x $80 per hour = $1,040 … $7 $1,047 $92,136

We estimate the following costs to do any necessary repairs for certain Models SA226-AT, SA226-TC, SA227-AC, and SA227-AT referenced in M7 Aerospace SA226 Series Service Bulletin 226-24-020, revised: August 4, 2008; or M7 Aerospace SA227 Series Service Bulletin 227-24-002, revised: November 21, 2008. We have no way of determining the number of airplanes that may need this repair:

Total cost per

Labor cost Parts cost airplane

50 work-hours x $80 per hour = $3,000 $7,000

$4,000 …

Authority for This Rulemaking

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in subtitle VII, part A, subpart III, section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

Regulatory Findings

We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that the proposed regulation:

1. Is not a "significant regulatory action" under Executive Order 12866;

2. Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.

Examining the AD Docket

Examining the AD Docket

You may examine the AD docket that contains the proposed AD, the regulatory evaluation, any comments received, and other information on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Office (telephone (800) 647-5527) is located at the street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. The FAA amends § 39.13 by removing Airworthiness Directive (AD) 2008-12-16, Amendment 39-15560 (73 FR 34615, June 18, 2008), and adding the following new AD:

§ 39.13 [Amended]

M7 Aerospace LP: Docket No. FAA-2009-0119; Directorate Identifier 2008-CE-068-AD.

Comments Due Date

(a) We must receive comments on this airworthiness directive (AD) action by April 13, 2009.

Affected ADs

(b) This AD supersedes AD 2008-12-16, Amendment 39-15560.

Applicability

(c) This AD applies to Models SA226-AT, SA226-T, SA226-TC, SA227-AC (C-26A), SA227-AT, SA227-BC (C-26A), SA227-CC, and SA227-DC (C-26B) airplanes, all serial numbers, that are certificated in any category.

Unsafe Condition

Unsafe Condition

(d) This AD results from five reports of chafing between the bleed air tube assembly and the electrical starter cables on M7 Aerospace LP SA226 and SA227 series airplanes with one incident resulting in a fire. We are proposing this AD to detect and correct chafing of electrical wires and components, hydraulic tube assemblies, and bleed air tube assemblies. This condition could result in arcing of the exposed wires with consequent burning of a hole in a hydraulic line or the bleed air line. This failure could lead to a possible hydraulic fluid leak and fire in the engine nacelle compartment.

Compliance

Compliance

(e) To address this problem, you must do the following, unless already done:

Actions Compliance Procedures

(1) For airplanes with the following Model Within 250 hours time-in-service Use the following service

Numbers (M/N) and Serial Numbers (S/N), (TIS) after July 23, 2008 (the information as applicable:

inspect the main battery leads running effective date of AD 2008-12- (A) For Models SA226-AT, SA226-

forward from the battery compartment for 16). T, and SA226-TC airplanes:

deterioration, cover the four-gauge wires Follow M7 Aerospace SA226

leaving the battery box with firesleeving, Series Service Bulletin No.

and secure them with a clamp: 226-24-019, revised: November

(i) M/N SA226-AT, S/N AT-001 through AT-419; 21, 2008; or Fairchild

(ii) M/N SA226-T, S/N T-201 through T-248; Aircraft Corporation SA226

(iii) M/N SA226-TC, S/N TC-201 through TC- Series Service Bulletin No. SB

419; 24-019, revised: May 17, 1983;

(iv) M/N SA227-AC (C-26A), S/N AC-420 through or

AC-539, AC-541, AC-543, AC-544, AC-547 (B) For Models SA227-AC (C-26A)

through AC-551; and and SA227-AT airplanes: Follow

(v) M/N SA227-AT, S/N AT-423 through AT-551. M7 Aerospace SA227 Series

Service Bulletin No. 227-24-

001, revised: November 21,

2008; or Fairchild Aircraft

Corporation SA227 Series

Service Bulletin No. SB24-001,

revised: May 17, 1983. (2) For airplanes with the following M/Ns and Before further flight after the Use the following service

S/Ns, reroute the hydraulic tube assemblies modification required in information as applicable:

in the right wing leading edge, reroute the paragraph (e)(1) of this AD and (A) For Models SA226-AT, and

battery cables and 22-gauge wire bundle, and you were not able to obtain a SA226-TC airplanes: Follow M7

install a new access panel forward of the minimum 0.50-inch clearance Aerospace SA226 Series Service

battery box: between the bleed air line and Bulletin No. 226-24-020,

(i) M/N SA226-AT, S/N AT-001 through AT-074; the tubing on the battery revised: August 4, 2008; or

(ii) M/N SA226-TC, S/N TC-201 through TC-419; cables. Fairchild Aircraft Corporation

(iii) M/N SA227-AC (C-26A), S/N AC-420 SA226 Series Service Bulletin

through AC-539, AC-541, AC-543, AC-544, AC- No. SB 24-020, revised:

547 through AC-550; and February 15, 1984; or

(iv) M/N SA227-AT, S/N AT-423 through AT-551. (B) For Models SA227-AC (C-26A)

and SA227-AT, airplanes:

Follow M7 Aerospace SA227

Series Service Bulletin No.

227-24-002, revised: November

21, 2008; or Fairchild

Aircraft Corporation SA227

Series Service Bulletin No.

SB24-002, revised: February

15, 1984.

(3) For airplane Models SA226-AT, SA226-T, Within 250 hours TIS after July Use the following service

SA226-TC, SA227-AC (C-26A), SA227-AT, SA227- 23, 2008 (the effective date of information as applicable:

CC, and SA227-DC (C-26B): Inspect electrical AD 2008-12-16). Repetitively (i) For Models SA226-AT, SA226-

wires and components, hydraulic tube thereafter inspect at intervals T, and SA226-TC airplanes:

assemblies, and bleed air tube assemblies at not to exceed 12 months. Follow M7 Aerospace SA226

the left hand and right hand (LH/RH) inboard Series Service Bulletin No.

wing leading edge/battery box areas, LH/RH 226-24-036, revised November

wing stations 51.167 to 81.174, and at all 21, 2008; or M7 Aerospace

feed-through locations into the LH/RH SA226 Series Service Bulletin

inboard keelson for any evidence of chafing No. 226-24-036, issued:

or arcing. September 19, 2007;

(ii) For Models SA227-AC (C-

26A) and SA227-AT, airplanes:

Follow M7 Aerospace SA227

Series Service Bulletin No.

227-24-019, revised: November

21, 2008; or M7 Aerospace

SA227 Series Service Bulletin

No. 227-24-019, issued:

September 19, 2007; or

(iii) For Models SA227-CC and

SA227-DC (C-26B) airplanes:

Follow SA227 Series Commuter

Category Service Bulletin No.

CC7-24-010, revised November

21, 2008; or SA227 Series

Commuter Category Service

Bulletin No. CC7-24-010,

issued September 19, 2007.

(4) For airplane Model SA227-BC (C-26A): Within 250 hours TIS after the Follow M7 Aerospace SA227

Inspect the main battery leads running effective date of this AD. Series Service Bulletin No.

forward from the battery compartment for any 227-24-001, revised: November

evidence of insulation deterioration. 21, 2008.

(5) For airplane Model SA227-BC (C-26A): Within 250 hours TIS after the Follow M7 Aerospace SA227

Inspect electrical wires and components, effective date of this AD. Series Service Bulletin No.

hydraulic tube assemblies, and bleed air Repetitively thereafter inspect 227-24-019, revised: November

tube assemblies at LH/RH inboard wing at intervals not to exceed 12 21, 2008.

leading edge/battery box areas, LH/RH wing months.

stations 51.167 to 81.174, and at all feed-through locations into the LH/RH inboard keelson for any evidence of insulation deterioration, chafing, or arcing.

(6) For all airplane Models: Clear, repair, Before further flight after any Use the service information

and/or replace all electrical wires and inspection required in from paragraphs (e)(1),

components, hydraulic tube assemblies, and paragraphs (e)(1), (e)(3), (e)(3), (e)(4), and (e)(5) of

bleed air tube assemblies, in the inspection (e)(4), and (e)(5) of this AD this AD, as applicable.

area and feed-through locations that show where any evidence of

any sign of insulation deterioration, insulation deterioration,

chafing, or arcing, as required. chafing, or arcing was found.

Note: Although not a requirement of this AD, you may incorporate Swearingen Aviation Corporation SA226 Series Service Bulletin No. 57-010, revised: December 5, 1975, on those airplanes that have not installed the access panel. Installation of the access panel will simplify the incorporation of the service bulletins referenced in this AD and future inspections of the areas of concern.

Alternative Methods of Compliance (AMOCs)

Alternative Methods of Compliance (AMOCs)

(f) The Manager, Fort Worth Airplane Certification Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Werner Koch, Aerospace Engineer, ASW-150, Fort Worth Airplane Certification Office, 2601 Meacham Blvd., Fort Worth, Texas 76137; telephone: (817) 222-5133; fax: (817) 222-5960. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.

Related Information

Related Information

(g) To get copies of the service information referenced in this AD, contact M7 Aerospace Repair Station, 10823 NE Entrance Road, San Antonio, Texas 78216; telephone: (210) 824-9421; fax: (210) 804-7766; Internet: http://www.m7aerospace.com. To view the AD docket, go to U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590, or on the Internet at http://www.regulations.gov.

Issued in Kansas City, Missouri, on February 6, 2009. Kim Smith, Manager, Small Airplane Directorate, Aircraft Certification Service.