Radar Vectors
Proposed Rule Proposed Issued Mar 1, 2007 6 pages Copy saved Nov 17, 2026

72 FR 9276 Airworthiness Directives; Pratt & Whitney JT9D-7R4 Turbofan Engines

The FAA proposes to supersede an existing airworthiness directive (AD) for Pratt & Whitney (PW) JT9D-7R4 turbofan engines. That AD currently requires inspection of the blade root thickness of 1st stage fan blades identified by part number (P/N) and serial number (SN) in the AD. This proposed AD would require the same actions but would correct 12 P/Ns, add 10 part SNs, and add the definition of next fan blade exposure to the compliance section. This proposed AD results from the discovery of inaccurate part quantity, part numbers, and serial numbers used in AD 2005-26-09. We are proposing this AD to prevent 1st stage fan blade fracture and uncontained engine failure, resulting in possible damage to the airplane.

This document is proposed. It may have been replaced. Check the official source before relying on it.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2005-23072; Directorate Identifier 2005-NE-38-AD] RIN 2120-AA64

Airworthiness Directives; Pratt & Whitney JT9D-7R4 Turbofan Engines

AGENCY: Federal Aviation Administration (FAA), Department of Transportation (DOT).

ACTION: Notice of proposed rulemaking (NPRM).

Summary

SUMMARY: The FAA proposes to supersede an existing airworthiness directive (AD) for Pratt & Whitney (PW) JT9D-7R4 turbofan engines. That AD currently requires inspection of the blade root thickness of 1st stage fan blades identified by part number (P/N) and serial number (SN) in the AD. This proposed AD would require the same actions but would correct 12 P/Ns, add 10 part SNs, and add the definition of next fan blade exposure to the compliance section. This proposed AD results from the discovery of inaccurate part quantity, part numbers, and serial numbers used in AD 2005-26-09. We are proposing this AD to prevent 1st stage fan blade fracture and uncontained engine failure, resulting in possible damage to the airplane.

Dates

DATES: We must receive any comments on this proposed AD by April 30, 2007.

ADDRESSES: Use one of the following addresses to comment on this proposed AD.

• DOT Docket Web site: Go to http://dms.dot.gov and follow the instructions for sending your comments electronically.

• Government-wide rulemaking Web site: Go to http://www.regulations.gov and follow the instructions for sending your comments electronically.

Addresses

• Mail: Docket Management Facility; U.S. Department of Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401, Washington, DC 20590-0001.

• Fax: (202) 493-2251.

• Hand Delivery: Room PL-401 on the plaza level of the Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Kevin Donovan, Aerospace Engineer, Engine Certification Office, FAA, Engine and Propeller Directorate, 12 New England Executive Park, Burlington, MA 01803-5299; telephone (781) 238-7743, fax (781) 238-7199.

SUPPLEMENTARY INFORMATION:

Comments Invited

Comments Invited

We invite you to send any written relevant data, views, or arguments regarding this proposal. Send your comments to an address listed under ADDRESSES. Include "Docket No. FAA-2005-23072; Directorate Identifier 2005-NE-38-AD" in the subject line of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the proposed AD. We will consider all comments received by the closing date and may amend the proposed AD in light of those comments.

We will post all comments we receive, without change, to http://dms.dot.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact with FAA personnel concerning this proposed AD. Using the search function of the DMS Web site, anyone can find and read the comments in any of our dockets, including the name of the individual who sent the comment (or signed the comment on behalf of an association, business, labor union, etc.). You may review the DOT's complete Privacy Act Statement in the Federal Register published on April 11, 2000 (65 FR 19477-78) or you may visit http://dms.dot.gov.

Examining the AD Docket

Examining the AD Docket

You may examine the docket that contains the proposal, any comments received and any final disposition in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Office (telephone (800) 647-5227) is located on the plaza level of the Department of Transportation Nassif Building at the street address stated in ADDRESSES. Comments will be available in the AD docket shortly after the DMS receives them.

Discussion

Discussion

On December 16, 2005, the FAA issued AD 2005-26-09, Amendment 39-14430 (70 FR 76381, December 27, 2005). That AD requires inspection of the blade root thickness of 1st stage fan blades identified by P/N and SN. That AD was the result of a report of a repair station that created an unapproved repair on 1st stage fan blades. That condition, if not corrected, could result in 1st stage fan blade fracture and uncontained engine failure, resulting in possible damage to the airplane.

Actions Since AD 2005-26-09 Was Issued

Actions Since AD 2005-26-09 Was Issued

Since AD 2005-26-09 was issued, we received comments on the AD requesting clarification. We considered those requests and have changed the compliance section in this proposed AD for clarification. We also found and corrected 12 incorrect P/Ns, and added 10 part SNs of affected 1st stage fan blades to Table 1 of this proposed AD. The comments and affected P/Ns and SNs are also discussed below.

Request To Clarify "At the Next 1st Stage Fan Blade Exposure"

Request To Clarify "At the Next 1st Stage Fan Blade Exposure"

Two air carriers request that we clarify "at the next 1st stage fan blade exposure," to prevent any in-service disruptions or delays. The commenter further states that the 1st stage fan blades can be exposed when:

• Some 1st stage fan blades are replaced due to in-service foreign object damage;

• A 1st stage fan hub is replaced and the same 1st stage fan blades are reused; and

• At shop visit when 1st stage fan blades are removed from the fan hub for cause or work scope.

We agree with adding a paragraph to the proposed AD which defines next 1st stage fan blade exposure. We have defined it as when any 1st stage fan blade is removed from the engine; or when the 1st stage fan hub is removed from the engine.

Suggestion To Report When Finding Affected 1st Stage Fan Blades

Suggestion To Report When Finding Affected 1st Stage Fan Blades

Air Canada suggests that operators finding any affected 1st stage fan blades should report back to the FAA. The commenter states that by requiring this reporting, all 520 of the blades can then be accounted for, and the FAA can close the AD. The commenter is also concerned that if some blades cannot be accounted for, such as blades already scrapped, misplaced, or shelved, then the AD will never be closed, and operators will be forced to verify the AD indefinitely at every 1st stage fan blade installation.

We do not agree. This proposed AD requires a onetime inspection for a specific population of 1st stage fan blades. If an operator has inspected and verified a certain set of 1st stage fan blades in accordance with the proposed AD, then at the next 1st stage fan blade exposure, only replacement blades that are listed in Table 1 of the proposed AD will require inspection and verification.

Request To Clarify or Remove Paragraph (e)

Request To Clarify or Remove Paragraph (e)

Air Canada states that compliance paragraph (e) mentions that the AD must be performed within the compliance times specified, but there are no times specified. The commenter requests this instruction be removed or clarified.

We partially agree. We revised the compliance times for clarification in the proposed AD.

Comment That "At Exposure" Limit Is Not a Practical Limit

Comment That "At Exposure" Limit Is Not a Practical Limit

ABX AIR claims that the "at exposure" limit in the AD is not practical. They said that "at exposure" will require the operators to set up a special inspection schedule to accomplish this onetime inspection which is not suitable for fleet operators.

We partially agree. Inspecting the affected parts at the next 1st stage fan blade exposure is sufficient. It is not necessary for operators to set up a special inspection schedule since this inspection does not impact the FAA-approved maintenance program procedures. However, for clarification, we added a definition for "next first stage fan blade exposure" to the proposed AD.

Request To Clarify "Before Installing the 1st Stage Fan Blades"

Request To Clarify "Before Installing the 1st Stage Fan Blades"

ABX AIR requests that we clarify "before installing the 1st stage fan blades" in paragraph (f). ABX believes the AD should contain a concise clarifying statement such as: "After the active date of this AD, no person may install, on any airplane, any blade listed in Table 1 of this AD unless the actions of this AD have already been accomplished."

We agree. We added a prohibition statement that states that after the effective date of this (proposed) AD, do not install any 1st stage fan blades listed in Table 1 of this AD on any airplane, unless the actions of this AD have been done to the 1st stage fan blades.

P/Ns Corrected, and P/Ns and SNs Added

P/Ns Corrected, and P/Ns and SNs Added

Since we issued AD 2005-26-09, we found and corrected 12 incorrect P/Ns, and added 10 part SNs of affected 1st stage fan blades in Table 1 of this proposed AD. The corrected numbers are as follows:

Corrected P/

Incorrect P/Ns Ns SNs

5001341-023 … 5001341-022 JW2313

5001341-024 … 5001341-022 JW2498

5001341-025 … 5001341-022 JW2541

5001341-026 … 5001341-022 JW2560

5001341-027 … 5001341-022 JW2589

5001341-028 … 5001341-022 JW2639

5001341-029 … 5001341-022 JW2760

5001341-030 … 5001341-022 JW2792

5001341-031 … 5001341-022 MO579

5001341-032 … 5001341-022 MG2825

5001341-033 … 5001341-022 MG5477

5001341-034 … 5001341-022 ND5917

The added part SNs are as follows:

PNs Added SNs

5001341-022 … JW4713

5001341-022 … MG6743

5001341-022 … ND6924

831021-003 … ND9177

831021-003 … ND9496

831021-003 … NS7894

831021-003 … NS8559

831021-003 … NS9072

804121 … PX3805

804121 … PX4266

Conclusion

Conclusion

We have carefully reviewed the available data, including the comments received, and determined that air safety and the public interest require proposing this AD with the changes described previously. We have determined that these changes will neither increase the economic burden on any operator nor increase the scope of the proposed AD.

FAA's Determination and Requirements of the Proposed AD

FAA's Determination and Requirements of the Proposed AD

We have evaluated all pertinent information and identified an unsafe condition that is likely to exist or develop on other products of this same type design. For that reason, we are proposing this AD, which would require:

• Checking the 1st stage fan blade for a circled, letter I, on the approved marking area of the outboard side of the blade platform. If the blade has this marking, no further action is required.

• Removing 1st stage fan blades without a circled, letter I, on the approved marking area of the outboard side of the blade platform if installed; and

• Inspecting the 1st stage fan blade root thickness; and

• Returning to service 1st stage fan blades that pass the inspection, after properly marking the blade.

Costs of Compliance

Costs of Compliance

We estimate that this proposed AD would affect 531 1st stage fan blades installed on JT9D-7R4 turbofan engines installed on airplanes of U.S. registry. We also estimate that it would take about 0.5 work-hour per 1st stage fan blade to perform the proposed actions, and that the average labor rate is $80 per work-hour. Based on these figures, we estimate the total cost of the proposed AD to U.S. operators to be $21,240.

Authority for This Rulemaking

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

Regulatory Findings

We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that the proposed AD:

1. Is not a "significant regulatory action" under Executive Order 12866;

2. Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Would not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD. See the ADDRESSES section for a location to examine the regulatory evaluation.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

Under the authority delegated to me by the Administrator, the Federal Aviation Administration proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. The FAA amends § 39.13 by removing Amendment 39-14430 (70 FR 76381, December 27, 2005), and by adding a new airworthiness directive to read as follows:

§ 39.13 [Amended]

Pratt & Whitney: Docket No. FAA-2005-23072; Directorate Identifier 2005-NE-38-AD.

Comments Due Date

(a) The Federal Aviation Administration (FAA) must receive comments on this airworthiness directive (AD) action by April 30, 2007.

Affected ADs

(b) This AD supersedes AD 2005-26-09.

Applicability

Applicability

(c) This AD applies to Pratt & Whitney (PW) JT9D-7R4 turbofan engines. These engines are installed on, but not limited to, Airbus A300 and A310, and Boeing 747 and 767 airplanes.

Unsafe Condition

(d) This AD results from the discovery of inaccurate part quantity, part numbers, and serial numbers used in AD 2005-26-09. We are issuing this AD to prevent 1st stage fan blade fracture and uncontained engine failure, resulting in possible damage to the airplane.

Compliance

Compliance

(e) You are responsible for having the actions required by this AD performed within the compliance times specified unless the actions have already been done.

(f) For 1st stage fan blades that are listed by part number (P/ N) and serial number (SN) in Table 1 of this AD, do the following:

Table 1.--Affected 1st Stage Fan Blades

P/Ns SNs

5001341-022 … JW2804

5001341-022 … JW0354

5001341-022 … ND5746

5001341-022 … ND5770

5001341-022 … JW3992

5001341-022 … ND8615

5001341-022 … JW0442

5001341-022 … JW2317

5001341-022 … ND8631

5001341-022 … ND8635

5001341-022 … JW4624

5001341-022 … NE0394

5001341-022 … NE0153

5001341-022 … NN8054

5001341-022 … JW4693

5001341-022 … ND7304

5001341-022 … MG6108

5001341-022 … MG5862

5001341-022 … MG5619

5001341-022 … NE0308

5001341-022 … NE0200

5001341-022 … MG6797

5001341-022 … JW0230

5001341-022 … ND5652

5001341-022 … ND5775

5001341-022 … JW0251

5001341-022 … ND5719

5001341-022 … JW0248

5001341-022 … ND5785

5001341-022 … ND5676

5001341-022 … ND5661

5001341-022 … JW0265

5001341-022 … ND5699

5001341-022 … ND5767

5001341-022 … JW0259

5001341-022 … ND5680

5001341-022 … ND5749

5001341-022 … JW0235

5001341-022 … ND5776

5001341-022 … ND8580

5001341-022 … MG6039

5001341-022 … ND9127

5001341-022 … JW4287

5001341-022 … JW0262

5001341-022 … JW0445

5001341-022 … JW4665

5001341-022 … MG5901

5001341-022 … NE0303

5001341-022 … ND8703

5001341-022 … JW4574

5001341-022 … JW4286

5001341-022 …

JW4491

5001341-022 … JW4630

5001341-022 … JW4391

5001341-022 … MG6550

5001341-022 … MG6776

5001341-022 … JW4586

5001341-022 … JW0352

5001341-022 … JW4261

5001341-022 … MG6135

5001341-022 … JW4685

5001341-022 … MG6772

5001341-022 … MG6793

5001341-022 … MG7111

5001341-022 … ND8618

5001341-022 … JW0644

5001341-022 … JW4631

5001341-022 … JW4651

5001341-022 … JW0234

5001341-022 … JW4646

804121 … NN9016

804121 … VJ3393

804121 … PX3694

804121 … RK9168

804121 … PX5023

804121 … VJ3324

804121 … VJ3504

804121 … NN9115

804121 … NN8936

804121 … PX3816

804121 … VJ3412

804121 … RK9163

804121 … VJ3447

804121 … RK9230

804121 … RK9109

804121 … PX4627

804121 … RK8990

804121 … SP9459

804121 … RK8656

804121 … NN8933

804121 … VJ3444

804121 … ND5864

804121 … NN9020

804121 … RK8905

804121 … SR1733

804121 … NN9047

804121 … PX3692

804121 … PX3786

804121 … NN9025

804121 … NN9007

804121 … RK9100

804121 … VJ3399

804121 … PX4970

804121 … PX5013

804121 … RK8904

804121 … NN8986

804121 … NN8829

804121 … VJ3459

804121 … RK9143

804121 … VJ3414

804121 … NN9028

804121 … SP1557

804121 … PX5003

804121 … PX5042

804121 …

VJ3475

804121 … ND7330

804121 … PX3714

831021-003 … NS8913

831021-003 … ND6512

831021-003 … ND6941

831021-003 … ND9576

831021-003 … NS7555

831021-003 … NS8286

831021-003 … NS7447

831021-003 … ND6488

831021-003 … ND8296

831021-003 … ND6956

831021-003 … ND7879

831021-003 … ND6509

831021-003 … ND9814

831021-003 … NN7331

831021-003 … ND6991

831021-003 … ND6894

831021-003 … NS6413

831021-003 … ND7344

831021-003 … ND6947

831021-003 … NN8732

831021-003 … ND8536

831021-003 … ND6946

831021-003 … ND6723

831021-003 … ND9294

831021-003 … ND9290

831021-003 … ND6013

831021-003 … ND8937

831021-003 … NS7160

831021-003 … NS6435

831021-003 … NS6591

831021-003 … ND9558

831021-003 … NS8479

831021-003 … NS9382

831021-003 … ND8965

831021-003 … ND9837

831021-003 … ND5959

831021-003 … NS6491

831021-003 … NS9072

831021-003 … ND9625

831021-003 … ND6714

831021-003 … ND6820

831021-003 … ND8972

831021-003 … NE0286

831021-003 … NE0347

831021-003 … ND8010

831021-003 … ND8956

831021-003 … ND9535

831021-003 … ND9831

831021-003 … NE0227

831021-003 … ND8283

831021-003 … ND9730

831021-003 … NN7656

831021-003 …

NS7775

831021-003 … ND9815

831021-003 … ND6135

831021-003 … NS8491

831021-003 … NS6395

831021-003 … NS8584

831021-003 … NN7272

831021-003 … MG7159

831021-003 … NS6592

831021-003 … ND7862

831021-003 … ND6684

831021-003 … NN7744

831021-003 … ND7480

831021-003 … ND7873

831021-003 … ND6827

831021-003 … ND6576

831021-003 … ND9261

831021-003 … NS8686

831021-003 … ND9052

831021-003 … ND6897

831021-003 … ND6565

831021-003 … NN8966

831021-003 … PX3707

831021-003 … NS7031

831021-003 … ND6584

831021-003 … ND9883

831021-003 … NS6535

831021-003 … ND7852

831021-003 … ND9662

831021-003 … ND7871

831021-003 … JW0106

831021-003 … ND8305

831021-003 … NS6409

831021-003 … NE0442

831021-003 … ND9095

831021-003 … ND9302

831021-003 … ND9023

831021-003 … ND8009

831021-003 … ND8477

831021-003 … ND7492

831021-003 … ND8776

831021-003 … ND6524

831021-003 … ND6704

831021-003 … ND8911

831021-003 … ND8789

831021-003 … ND8798

831021-003 … ND6407

831021-003 … ND7668

831021-003 … ND9179

831021-003 … NE0421

831021-003 … ND6513

831021-003 … ND6744

831021-003 … ND7654

831021-003 … ND7870

831021-003 … ND9759

831021-003 …

ND6561

831021-003 … ND5826

831021-003 … ND6031

831021-003 … ND8714

831021-003 … ND8872

831021-003 … ND6678

831021-003 … ND6629

831021-003 … ND8995

831021-003 … NE0302

831021-003 … ND6405

831021-003 … NS8300

831021-003 … NS8769

831021-003 … NS7147

831021-003 … ND6649

831021-003 … ND7766

831021-003 … NS7864

831021-003 … NS8734

831021-003 … ND6677

831021-003 … NS7911

831021-003 … ND8205

831021-003 … ND8804

831021-003 … ND6639

831021-003 … ND8994

831021-003 … ND7275

831021-003 … ND9195

831021-003 … ND6178

831021-003 … ND8639

831021-003 … ND9760

831021-003 … ND9108X

831021-003 … ND6427

831021-003 … ND6590

831021-003 … NS6551

831021-003 … JW1158

831021-003 … ND6412

831021-003 … ND7922

831021-003 … NS8678

831021-003 … ND8930

831021-003 … ND6596

831021-003 … ND9570

831021-003 … NN9027

831021-003 … ND6446

831021-003 … NE0275

831021-003 … ND9917

831021-003 … NS7919

831021-003 … NS7907

831021-003 … ND6583

831021-003 … NN7420

831021-003 … ND7746

831021-003 … ND8187

831021-003 … NN8999

831021-003 … ND6043

831021-003 … ND7880

831021-003 … NN7175

831021-003 … ND9816

831021-003 … ND8174

831021-003

… ND6045

831021-003 … NS7562

831021-003 … JW0075

831021-003 … ND6848

831021-003 … ND8531

831021-003 … ND6311

831021-003 … ND8144

831021-003 … ND5798

831021-003 … ND8113

831021-003 … ND9642

831021-003 … ND7436

831021-003 … ND9054

831021-003 … ND9683

831021-003 … ND5991

831021-003 … ND6026

831021-003 … ND6616

831021-003 … ND6530

831021-003 … NE0374

831021-003 … ND6364

831021-003 … ND7718

831021-003 … ND6473

831021-003 … ND6436

831021-003 … ND6887

831021-003 … ND6518

831021-003 … ND6479

831021-003 … NS6330

831021-003 … ND7264

831021-003 … ND8151

831021-003 … ND6562

831021-003 … NS8776

831021-003 … ND6519

831021-003 … ND7659

831021-003 … NS9049

831021-003 … NS6861

831021-003 … ND9571

831021-003 … ND9346

831021-003 … ND6501

831021-003 … NS8505

831021-003 … ND9338

831021-003 … ND9775

831021-003 … ND6485

831021-003 … ND7165

831021-003 … ND9371

831021-003 … ND9537

831021-003 … NS7889

831021-003 … ND7877

831021-003 … ND8670

831021-003 … ND9032

831021-003 … ND8781

831021-003 … ND8604

831021-003 … ND9329

831021-003 … ND9110

831021-003 … ND5997

831021-003 … ND6027

831021-003 … ND9589

831021-003

… ND6575

831021-003 … ND6592

831021-003 … ND6463

831021-003 … NS8583

831021-003 … NS8590

831021-003 … NS8567

831021-003 … NS6795

831021-003 … NS7110

831021-003 … NS6587

831021-003 … NS6404

831021-003 … ND6486

5001341-022 … JW0942

5001341-022 … ND9231

5001341-022 … JW4812

5001341-022 … ND6555

5001341-022 … M1375

5001341-022 … MG6627

5001341-022 … MG6794

5001341-022 … ND9399

5001341-022 … NE0084

5001341-022 … MG6252

5001341-022 … ND7422

5001341-022 … ND7043

5001341-022 … MG5722

5001341-022 … MG5918

5001341-022 … ND6984

5001341-022 … M0839

5001341-022 … M0922

5001341-022 … M0938

5001341-022 … M1117

5001341-022 … M0307

5001341-022 … JW3871

5001341-022 … M1125

5001341-022 … M1149

5001341-022 … JW2681

5001341-022 … M0270

5001341-022 … M1120

5001341-022 … M0205

5001341-022 … AE9352

5001341-022 … JW3492

5001341-022 … ND6148

5001341-022 … ND8907

5001341-022 … M1235

5001341-022 … MG5585

5001341-022 … ND8436

5001341-022 … MG5696

5001341-022 … ND8704

5001341-022 … JW2284

5001341-022 … JW2313

5001341-022 … JW2498

5001341-022 … JW2541

5001341-022 … JW2560

5001341-022 … JW2589

5001341-022 …

JW2639

5001341-022 … JW2760

5001341-022 … JW2792

5001341-022 … M0579

5001341-022 … MG2825

5001341-022 … MG5477

5001341-022 … ND5917

5001341-022 … JW1976

5001341-022 … JW2653

5001341-022 … JW2608

5001341-022 … JW2727

5001341-022 … JW2764

5001341-022 … JW2265

5001341-022 … JW2474

5001341-022 … JW2396

5001341-022 … JW3554

5001341-022 … JW2667

5001341-022 … MG2302

5001341-022 … MG3972

5001341-022 … JW3930

5001341-022 … ND6749

5001341-022 … M1172

5001341-022 … JW2104

5001341-022 … JW2519

5001341-022 … JW2640

5001341-022 … JW2517

5001341-022 … JW2663

5001341-022 … JW2823

5001341-022 … M0536

5001341-022 … JW2725

5001341-022 … MG5917

5001341-022 … JW0681

5001341-022 … JW0711

5001341-022 … JW0740

5001341-022 … JW0807

5001341-022 … JW1089

5001341-022 … JW1362

5001341-022 … JW2065

5001341-022 … MG2434

5001341-022 … MG2846

5001341-022 … JW0806

804121 … NN9854

804121 … NN9024

804121 … NN9032

804121 … PX5029

804121 … NN9050

804121 … NS8242

804121 … NS8260

804121 … PX4273

804121 … PX4378

804121 … RL0857

804121 … RX8763

804121 … NS8331

804121 … NN9824

804121 … MG6979

804121 … MG7023

804121 …

MG7055

804121 … RK8914

804121 … RL0023

804121 … PX4328

804121 … RK9008

804121 … TG1506

804121 … KK8226

804121 … MG2604

804121 … NS6691

804121 … RK8968

804121 … NN9917

804121 … RK7824

804121 … M1343

804121 … NS6559

804121 … NS7767

804121 … NE0363

804121 … PX3771

804121 … NN9972

804121 … RL0460

804121 … RK8310

804121 … SR2115

804121 … TG2826

804121 … PX5018

804121 … PX5002

831021-003 … ND7627

831021-003 … ND6890

831021-003 … ND7461

831021-003 … ND9616

831021-003 … NE0413

831021-003 … NS8825

831021-003 … NS6350

831021-003 … NS7168

831021-003 … NS7705

831021-003 … NS7848

831021-003 … ND9128

831021-003 … ND9541

831021-003 … ND9671

831021-003 … ND9684

831021-003 … NE0277

831021-003 … NE0384

831021-003 … NE0396

831021-003 … ND6421

831021-003 … ND6599

831021-003 … ND6614

831021-003 … ND7847

831021-003 … ND8346

831021-003 … ND8853

831021-003 … ND8915

831021-003 … NS8719

831021-003 … NS8838

831021-003 … NT0169

831021-003 … NS9584

831021-003 … ND6445

831021-003 … ND6834

831021-003 … ND7467

831021-003 … ND8887

831021-003 … ND6520

831021-003 … NS8611

831021-003 … NS7640

831021-003 …

NN7037

831021-003 … NN7590

831021-003 … NN8120

831021-003 … NN8573

831021-003 … NN9719

831021-003 … NS8784

831021-003 … TB6B367

831021-003 … NN9557

831021-003 … NN9710

831021-003 … NS8374

831021-003 … NS8770

831021-003 … NS9022

831021-003 … NS8416

831021-003 … NS6474

831021-003 … ND8912

831021-003 … NT0108

831021-003 … NS8836

831021-003 … NN8310

831021-003 … NS8559

5001341-022 … JW4713

5001341-022 … MG6743

5001341-022 … ND6924

831021-003 … ND9177

831021-003 … ND9496

831021-003 … NS7894

831021-003 … NS8559

831021-003 … NS9072

804121 … PX3805

804121 … PX4266

For Engines Installed on an Airplane

For Engines Installed on an Airplane

(1) For engines installed on an airplane with affected 1st stage fan blades installed, perform the actions in paragraphs (f)(3) through (f)(6)(ii) of this AD at the next 1st stage fan blade exposure.

For Engines Not Installed on an Airplane, or, for Affected 1st Stage Fan Blades Not Installed in an Engine

For Engines Not Installed on an Airplane, or, for Affected 1st Stage Fan Blades Not Installed in an Engine

(2) For engines not installed on an airplane with affected 1st stage fan blades installed, or, for affected 1st stage fan blades not installed in an engine, paragraph (h) of this AD applies.

1st Stage Fan Blade Check

(3) Check the 1st stage fan blade for a circled, letter I, on the approved marking area of the outboard side of the blade platform. If the blade has this marking, no further action is required.

1st Stage Fan Blade Check

(4) Remove 1st stage fan blades without a circled, letter I, on the approved marking area of the outboard side of the blade platform, if installed.

(5) Inspect the 1st stage fan blade root thickness. You can find information on inspecting the blade root thickness in PW Engine Manual Section 72-31-02, Inspect-01, and Repair-23.

(6) For 1st stage fan blades that pass the inspection referenced in paragraph (f)(5) of this AD:

(i) Vibropeen the letter I and a circle around that letter, on the approved marking area of the outboard side of the blade platform. You can find information on approved blade marking in the JT9D-7R4 Engine Manual, Section 72-31-02, Typical Repair-13, Mark Repair Codes.

(ii) Return the 1st stage fan blades to service.

Definition

Definition

(g) For the purposes of paragraph (f)(1) of this AD, next 1st stage fan blade exposure is:

(1) When any 1st stage fan blade is removed from the engine; or

(2) When the 1st stage fan hub is removed from the engine.

Prohibited Installation

(h) After the effective date of this AD, do not install any 1st stage fan blades listed in Table 1 of this AD on any airplane, unless the actions of this AD have been done to the 1st stage fan blades.

Alternative Methods of Compliance

Alternative Methods of Compliance

(i) The Manager, Engine Certification Office, has the authority to approve alternative methods of compliance for this AD if requested using the procedures found in 14 CFR 39.19.

Related Information

(j) None.

Issued in Burlington, Massachusetts, on February 23, 2007. Peter A. White, Acting Manager, Engine and Propeller Directorate, Aircraft Certification Service.