Radar Vectors
Proposed Rule Proposed Issued Dec 10, 2007 6 pages Copy saved Nov 17, 2026

72 FR 69630 Airworthiness Directives; Taylorcraft Aviation, LLC A, B, and F Series Airplanes

We propose to supersede Airworthiness Directive (AD) AD 2007-16-14, which applies to all Taylorcraft Aviation, LLC (Taylorcraft) A, B, and F series airplanes. AD 2007-16-14 currently requires you to do an initial visual inspection of the left and right wing front and aft lift struts for cracks and corrosion and replace any cracked strut or strut with corrosion that exceeds certain limits. If the strut is replaced with an original design vented strut, AD 2007-16-14 requires you to repetitively inspect those struts thereafter. Since we issued AD 2007-16-14, we determined that the eddy current inspection method does not address the unsafe condition for the long term. We also determined that Models FA-III and TG-6 airplanes are not equipped with the affected struts. Consequently, this proposed AD would retain the actions required in AD 2007-16-14, except it removes the eddy current inspection method (provides 24-month credit if already done using this method), adds the radiograph method as an inspection method, changes the Applicability section, and changes the compliance time between the repetitive inspections. We are issuing this proposed AD to detect and correct cracks and corrosion in the right and left wing front and aft lift struts. This condition, if not corrected, could result in failure of the lift strut and lead to in-flight separation of the wing.

This document is proposed. It may have been replaced. Check the official source before relying on it.

Official source ↗ Official PDF ↗

14 CFR Part 39

[Docket No. FAA-2007-0286; Directorate Identifier 2007-CE-086-AD] RIN 2120-AA64

Airworthiness Directives; Taylorcraft Aviation, LLC A, B, and F Series Airplanes

AGENCY: Federal Aviation Administration (FAA), Department of Transportation (DOT).

ACTION: Notice of proposed rulemaking (NPRM).

Summary

SUMMARY: We propose to supersede Airworthiness Directive (AD) AD 2007-16-14, which applies to all Taylorcraft Aviation, LLC (Taylorcraft) A, B, and F series airplanes. AD 2007-16-14 currently requires you to do an initial visual inspection of the left and right wing front and aft lift struts for cracks and corrosion and replace any cracked strut or strut with corrosion that exceeds certain limits. If the strut is replaced with an original design vented strut, AD 2007-16-14 requires you to repetitively inspect those struts thereafter. Since we issued AD 2007-16-14, we determined that the eddy current inspection method does not address the unsafe condition for the long term. We also determined that Models FA-III and TG-6 airplanes are not equipped with the affected struts. Consequently, this proposed AD would retain the actions required in AD 2007-16-14, except it removes the eddy current inspection method (provides 24-month credit if already done using this method), adds the radiograph method as an inspection method, changes the Applicability section, and changes the compliance time between the repetitive inspections. We are issuing this proposed AD to detect and correct cracks and corrosion in the right and left wing front and aft lift struts. This condition, if not corrected, could result in failure of the lift strut and lead to in-flight separation of the wing.

Dates

DATES: We must receive comments on this proposed AD by January 9, 2008.

ADDRESSES: Use one of the following addresses to comment on this proposed AD:

• Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments.

• Fax: (202) 493-2251.

Addresses

• Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590.

• Hand Delivery: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

For service information identified in this proposed AD, contact Taylorcraft Aviation, LLC, 2124 North Central Avenue, Brownsville, Texas 78521; telephone: 956-986-0700.

For Further Information Contact

FOR FURTHER INFORMATION CONTACT: Andrew McAnaul, Aerospace Engineer, ASW-150 (c/o MIDO-43), 10100 Reunion Place, Suite 650, San Antonio, Texas 78216; telephone: (210) 308-3365; fax: (210) 308-3370.

SUPPLEMENTARY INFORMATION:

Comments Invited

We invite you to send any written relevant data, views, or arguments regarding this proposed AD. Send your comments to an address listed under the ADDRESSES section. Include the docket number, "FAA-2007-0286; Directorate Identifier 2007-CE-086-AD" at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the proposed AD. We will consider all comments received by the closing date and may amend the proposed AD in light of those comments.

Comments Invited

We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive concerning this proposed AD.

Discussion

Reports of several corroded vented wing lift struts from different Taylorcraft series airplanes caused us to issue AD 2007-16-14, Amendment 39-15153 (72 FR 45153, August 13, 2007). AD 2007-16-14 currently requires the following on all Taylorcraft A, B, and F series airplanes:

Discussion

• Initial visual inspection of the left and right wing front and aft lift struts for cracks and corrosion;

• Replacement of any cracked strut or strut with corrosion that exceeds certain limits with either sealed or vented struts; and

• Repetitive eddy current or ultrasound inspection of any vented lift struts.

Since issuing AD 2007-16-14, we received several comments concerning the AD. We reviewed all comments submitted to the docket. The following are significant comments that influenced our decision to propose superseding AD 2007-16-14 with a new AD:

Comment FAA discussion

We received several requests to use the We approved the radiograph

We received several requests to use the We approved the radiograph

radiograph inspection method as an inspection procedure as an

alternative method of compliance AMOC for the repetitive

(AMOC) for doing the repetitive strut inspections required in AD

inspection. 2007-16-14, and the

manufacturer has added the

procedures for the radiograph

inspection to their revised

service bulletin.

We received several requests to Based on the inspection methods

increase the compliance time between used and the requirement to

repetitive inspections because the apply corrosion inhibitor to

Taylorcraft service information the strut interior at each

requires the application of corrosion inspection, we believe there

inhibitor to the interior of the strut is not an increased safety

inhibitor to the interior of the strut is not an increased safety

at each inspection. The commenters risk to the public by

also requested a longer compliance increasing the compliance time

time between repetitive inspections between the repetitive

for land planes compared to float inspections from 24 months to

equipped planes. 48 months for all airplanes.

We do not have sufficient

information to determine if a

different inspection interval

for land and float equipped

airplanes is valid.

We received a request to use Univair We have approved using these

part numbers (P/N) UA-A815 and UA-854 parts as an AMOC to AD 2007-16-

as a terminating action for the 14.

repetitive inspection requirement on Taylorcraft Models BC12-D/D1 and BCS12-D/D1 airplanes. We received several requests to install We did not intend to preclude used vented lift struts that have been owners from installing these inspected using the criteria specified parts. Vented lift struts that

in paragraph (e)(2) of AD 2007-16-14. are inspected using the

ultrasound or radiograph

inspection method, that meet

the Acceptance/Rejection

Criteria specified in

Taylorcraft Aviation, LLC

Service Bulletin No. 2007-001,

Revision B, dated October 15,

2007, and that are treated

with internal corrosion

protection are considered new

struts.

In addition to the comments above, we also received several reports of the following:

• The eddy current inspection method currently required in AD 2007-16-14 may not adequately address the unsafe condition for the long term; and

• Models FA-III (Airphibian) and TG-6 Conversion airplanes do not have the affected struts installed.

The following is a significant comment that did not influence our decision to propose superseding AD 2007-16-14 with a new AD:

Comment FAA discussion

We received several requests to use the Testing of Taylorcraft strut

We received several requests to use the Testing of Taylorcraft strut

Maule Fabric Tester as an AMOC for samples with the Maule Fabric

doing the repetitive strut inspection. Tester shows that both 1025

steel material, and to a

greater degree 4130 steel

material, resist showing a

positive dent indication until

doing the repetitive strut inspection. Tester shows that both 1025

a major portion of the wall

thickness is consumed.

Taylorcraft used 4130 steel in

a majority of their wing

struts during production. We

have not received any data

substantiating that

Taylorcraft wing struts can

still carry required

certification loads at the

reduced strut wall material

thickness indicated in the

testing.

Cracks and corrosion in the right and left wing front and aft lift struts, if not detected and corrected, could result in failure of the wing lift strut and lead to in-flight separation of the wing.

Relevant Service Information

Relevant Service Information

We reviewed Taylorcraft Aviation, LLC Service Bulletin (SB) No. 2007-001, Revision B, dated October 15, 2007.

The service information describes procedures for wing lift strut assembly corrosion inspection and/or replacement.

FAA's Determination and Requirements of the Proposed AD

FAA's Determination and Requirements of the Proposed AD

We are proposing this AD because we evaluated all information and determined the unsafe condition described previously is likely to exist or develop on other products of the same type design. This proposed AD would supersede AD 2007-16-14 with a new AD that would do the following:

• Retain the actions of AD 2007-16-14;

• Remove the eddy current inspection method, but allow a 24-month credit for those who already inspected once using the eddy current method;

• Remove Models FA-III (Airphibian) and TG-6 Conversion airplanes from the Applicability section;

• Add the radiograph inspection method;

• Increase the time interval between the repetitive inspections;

• Allow the installation of Univair P/Ns UA-A815 and UA-854 on Taylorcraft Models BC12-D/D1 and BCS12-D/D1 airplanes as a terminating action for the repetitive inspection requirement; and

• Allow the installation of used vented lift struts that have been inspected using ultrasound or radiograph inspection methods, meet the Acceptance/Rejection Criteria specified in Taylorcraft Aviation, LLC Service Bulletin No. 2007-001, Revision B, dated October 15, 2007, and have corrosion inhibitor applied to the interior of the strut. These lift struts are then subject to the repetitive 48-month inspection thereafter.

We have determined that the Maule Fabric Tester is not a viable AMOC to this AD.

This proposed AD would require you to use the service information described previously to perform these actions.

Costs of Compliance

Costs of Compliance

We estimate that this proposed AD would affect 3,119 airplanes in the U.S. registry.

We estimate the following costs to do the proposed visual inspection:

Total cost per Total cost on

Labor cost Parts cost airplane U.S. operators

1 work-hour x $80 per hour = $80 … Not applicable … $80 $249,520

We estimate the following costs to do the proposed repetitive ultrasound or radiograph inspection:

Total cost per

Labor cost Parts cost airplane

4 work-hours x $80 per hour = $320 Not applicable … $320

We estimate the following costs to do any necessary replacements that would be required based on the results of the proposed inspections. We have no way of determining the number of airplanes that may need this replacement:

Total cost per

airplane to

Labor cost Parts cost replace all 4 wing

lift struts

4 work-hours to replace all 4 Sealed front lift $1,670 + $1,276 +

struts x $80 per hour = $320. strut: $835 per $320 = $3,266.

strut. 2 per

airplane = $1,670.

Sealed aft lift

strut: $638 per

strut. 2 per

airplane = $1,276.

Original design vented lift struts are no longer manufactured. We have no way of determining the cost associated with obtaining a useable vented strut.

The estimated total cost on U.S. operators includes the cumulative costs associated with AD 2007-16-14 and any actions being added in this proposed AD.

Authority for This Rulemaking

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.

We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, "General requirements." Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

Regulatory Findings

We have determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that the proposed regulation:

1. Is not a "significant regulatory action" under Executive Order 12866;

2. Is not a "significant rule" under the DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and

3. Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

We prepared a regulatory evaluation of the estimated costs to comply with this proposed AD and placed it in the AD docket.

Examining the AD Docket

Examining the AD Docket

You may examine the AD docket that contains the proposed AD, the regulatory evaluation, any comments received, and other information on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Office (telephone (800) 647-5527) is located at the street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt.

List of Subjects in 14 CFR Part 39

List of Subjects in 14 CFR Part 39

Air transportation, Aircraft, Aviation safety, Safety.

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39--AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

PART 39--AIRWORTHINESS DIRECTIVES

Authority: 49 U.S.C. 106(g), 40113, 44701.

§ 39.13 [Amended]

2. The FAA amends § 39.13 by removing Airworthiness Directive (AD) 2007-16-14, Amendment 39-15153 (72 FR 45153, August 13, 2007), and by adding a new AD to read as follows:

Taylorcraft Aviation, LLC: Docket No. FAA-2007-0286; Directorate Identifier 2007-CE-086-AD.

Comments Due Date

Comments Due Date

(a) We must receive comments on this airworthiness directive (AD) action by January 9, 2008.

Affected ADs

(b) This AD supersedes AD 2007-16-14, Amendment 39-15153.

Applicability

(c) This AD applies to all serial numbers of Taylorcraft Models A, BC, BCS, BC-65, BCS-65, BC12-65 (Army L-2H), BCS12-65, BC12-D, BCS12-D, BC12-D1, BCS12-D1, BC12D-85, BCS12D-85, BC12D-4-85, BCS12D-4-85, (Army L-2G) BF, BFS, BF-60, BFS-60, BF-65, (Army L-2K) BF 12-65, BFS-65, BL, BLS, (Army L-2F) BL-65, BLS-65, (Army L-2J) BL12-65, BLS12-65, 19, F19, F21, F21A, F21B, F22, F22A, F22B, and F22C airplanes that:

Applicability

(1) Are certificated in any category; and

(2) Do not incorporate sealed wing front lift struts, part number (P/N) MA-A815, Univair P/N UA-A815 (for Models BC12-D/D1 and BCS12-D/D1 only), or FAA-approved equivalent P/N, and sealed aft lift struts, P/N MA-A854, Univair P/N UA-854 (for Models BC12-D/D1 and BCS12-D/D1 only), or FAA-approved equivalent P/N, for all struts.

Note 1: This AD applies to all Taylorcraft models listed above, including those models not listed in Taylorcraft Aviation, LLC Service Bulletin No. 2007-001, Revision B, dated October 15, 2007. If there are any other differences between this AD and the above service bulletin, this AD takes precedence.

Note 2: For the purposes of this AD, a used strut that has been inspected using the ultrasound or radiograph inspection method, meets the Acceptance/Rejection Criteria specified in Taylorcraft Aviation, LLC Service Bulletin No. 2007-001, Revision B, dated October 15, 2007, and is treated with internal corrosion protection, is considered a new strut.

Unsafe Condition

Unsafe Condition

(d) This AD results from our determination that the radiograph inspection method should be used in place of the eddy current inspection method currently required in AD 2007-16-14. We are issuing this AD to detect and correct corrosion or cracks in the right and left wing front and aft lift struts, which could result in failure of the lift strut and lead to in-flight separation of the wing with consequent loss of control.

Compliance

Compliance

(e) To address this problem, you must do the following, unless already done:

Actions Compliance Procedures

(1) Visually inspect the right Within the next 5 Follow Part 1 of

and left wing front and aft hours TIS after the Instructions

lift struts, (P/N A-A815 and P/ August 20, 2007 in Taylorcraft

N A-A854, or FAA-approved (the effective Aviation, LLC

equivalent P/Ns), along the date of AD 2007- Service Bulletin

entire bottom 12 inches of each 16-14), unless No. 2007-001,

strut for cracks and corrosion. one of the Revision A, dated

following August 1, 2007;

conditions is or Taylorcraft

met: Aviation, LLC

(i) The struts Service Bulletin

have been No. 2007-001,

replaced with Revision B, dated

parts specified October 15, 2007.

in paragraph

(e)(2)(i) of this

AD. No further

action is

required on those

struts.

(ii) The struts

have been

replaced with

parts specified

in paragraph

(e)(2)(ii) of

this AD and have

been installed

for less than 48

months. No visual

inspection is

required. These

parts are now

subject to the

repetitive

inspection

requirement

specified in

paragraph (e)(4)

of this AD.

(2) If any cracks are found Before further Following the

during the visual inspection flight after the Instructions in

required in paragraph (e)(1) of visual inspection Taylorcraft

this AD, replace the cracked required in Aviation, LLC

strut with the following paragraph (e)(1) Service Bulletin

applicable strut: of this AD. No. 2007-001,

required in paragraph (e)(1) of visual inspection Taylorcraft

Revision B, dated

October 15, 2007.

(i) A sealed front lift

strut, P/N MA-A815, Univair

P/N UA-A815 (for Models

BC12-D/D1 and BCS12-D/D1

only), or FAA-approved

equivalent P/N, a sealed

aft lift strut, P/N MA-

A854, Univair P/N UA-854

(for Models BC12-D/D1 and

BCS12-D/D1 only), or FAA-

approved equivalent P/N.

Installing these lift

struts terminates the

repetitive inspections

required by this AD for

that strut and no further

action is required.

(ii) A new vented front lift

strut, P/N A-A815, a new

vented aft lift strut, P/N

A-A854, or FAA-approved

equivalent P/Ns, that is

treated with internal

corrosion protection

specified in Taylorcraft

Aviation, LLC Service

Bulletin No. 2007-001,

Revision B, dated October

15, 2007. Installing one of

these lift struts is

subject to the repetitive

inspections required in

paragraph (e)(4) of this AD.

(3) If corrosion is found during Before further Follow Part 2 of

the inspection required in flight after the the Instructions

paragraph (e)(1) of this AD, do visual inspection in Taylorcraft

paragraph (e)(1) of this AD, do visual inspection in Taylorcraft

an ultrasound or radiograph required in Aviation, LLC

inspection to determine if the paragraph (e)(1) Service Bulletin

corrosion exceeds the of this AD. No. 2007-001,

Acceptance/Rejection Criteria Revision B, dated

specified in Taylorcraft October 15, 2007.

Aviation, LLC Service Bulletin All ultrasound or

No. 2007-001, Revision B, dated radiograph

October 15, 2007. inspections

required by this

AD must be done

by one of the

following:

(i) A Level II or

III inspector

certified in the

applicable

ultrasound or

radiograph

inspection method

using the

guidelines

established by

the American

Society of

Nondestructive

Testing or NAS

410 (formerly MIL-

STD-410);

(ii) An inspector

certified to

specific FAA or

other acceptable

government or

industry

standards, such

as Air Transport

Association (ATA)

Specifications

105-Guidelines

for Training and

Qualifying

Personnel in

Nondestructive

Testing Methods;

or

(iii) An FAA

Repair Station or

a Testing/

Inspection

Laboratory

qualified to do

ultrasound or

radiograph

inspections.

(4) If no corrosion or cracks (i) Initially Follow Part 2 of

are found during the visual inspect within the Instructions

inspection required in the next 3 months in Taylorcraft

paragraph (e)(1) of this AD, or after August 20, Aviation, LLC

if the inspection required in 2007 (the Service Bulletin

paragraph (e)(3) reveals that effective date of No. 2007-001,

the corrosion does not exceed AD 2007-16-14) or Revision B, dated

the Acceptance/Rejection within 48 months October 15, 2007,

Criteria specified in after installing using the

Taylorcraft Aviation, LLC a lift strut ultrasound or

Service Bulletin No. 2007-001, specified in radiograph

Revision B, dated October 15, paragraph inspection

2007, repetitively inspect (e)(2)(ii) of method.

thereafter using the ultrasound this AD, or radiograph inspection method whichever occurs

thereafter using the ultrasound this AD, or radiograph inspection method whichever occurs

and treat with internal later.

corrosion protection until all (ii) Repetitively

struts are replaced with the inspect

sealed struts specified in thereafter at

paragraph (e)(2)(i) of this AD. intervals not to

paragraph (e)(2)(i) of this AD. intervals not to

If any cracks are found or exceed 48 months,

corrosion is found that exceeds except as

the Acceptance/Rejection required by

Criteria specified in paragraph

Taylorcraft Aviation, LLC (e)(4)(iii) of

Service Bulletin No. 2007-001, this AD.

Revision B, dated October 15, (iii) If the

2007, during any of the initial

repetitive inspections required inspection was

repetitive inspections required inspection was

by this AD, take the necessary done using the

corrective actions as eddy current

applicable in paragraph (e)(5) method as

of this AD. specified in AD

2007-16-14, the

first ultrasound

or radiograph

repetitive

inspection must

be done within

the next 24

months after

doing the eddy

current

inspection.

Repetitively

inspect

thereafter at

intervals not to

exceed 48 months

using the

ultrasound or

radiograph

inspection method.

(5) If, during any inspection Before further Following the

required in paragraphs (e)(3) flight after the Instructions in

or (e)(4) of this AD, any inspection Taylorcraft

cracks are found or it is required in Aviation, LLC

determined that the corrosion paragraph (e)(3) Service Bulletin

exceeds the Acceptance/ or (e)(4) of this No. 2007-001,

Rejection Criteria specified in AD. Revision B, dated

Taylorcraft Aviation, LLC October 15, 2007.

Service Bulletin No. 2007-001, Revision B, dated October 15, 2007, replace the lift strut with the applicable lift strut specified in paragraph (e)(2)(i) or (e)(2)(ii) of this AD. (6) Do not install P/N A-A815, P/ As of 5 hours TIS Not applicable.

N A-A854, or FAA-approved after the

equivalent P/N, unless: effective date of

this AD.

(i) within the last 48

months it has been

inspected using the

ultrasound or radiograph

method;

(ii) meets the Acceptance/

Rejection Criteria; and

(iii) is treated with

internal corrosion

protection as specified in

Taylorcraft Aviation, LLC

Service Bulletin No. 2007-

001, Revision B, dated

October 15, 2007.

(7) As a terminating action for At any time after Not applicable.

the repetitive inspections the effective

required by this AD, all vented date of this AD. lift struts (P/Ns A-A815, A-A854, and FAA-approved equivalent P/Ns) may be replaced with sealed lift struts (P/Ns MA-A815, UA-A815 (for Models BC12-D/D1 and BCS12-D/D1 only), MA-A854, UA-854 (for Models BC12-D/D1 and BCS12-D/D1 only), or FAA-approved equivalent P/Ns).

Alternative Methods of Compliance (AMOCs)

Alternative Methods of Compliance (AMOCs)

(f) The Manager, Fort Worth Airplane Certification Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Andrew McAnaul, Aerospace Engineer, ASW-150 (c/o MIDO-43), 10100 Reunion Place, Suite 650, San Antonio, Texas 78216; telephone: (210) 308-3365; fax: (210) 308-3370. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO.

(g) AMOCs approved for AD 2007-16-14 are approved for this AD.

Related Information

Related Information

(h) To get copies of the service information referenced in this AD, contact Taylorcraft Aviation, LLC, 2124 North Central Avenue, Brownsville, Texas 78521; telephone: 956-986-0700. To view the AD docket, go to U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590, or on the Internet at http://www.regulations.gov.

Issued in Kansas City, Missouri, on December 3, 2007. John R. Colomy, Acting Manager, Small Airplane Directorate, Aircraft Certification Service.